The sustainable development of an area is highly dependable on reliable electrical energy supply. Microgrids are important in integrating distributed energy resources (DERs) using power electronic converters. However, microgrid control becomes challenging with the increasing number of distributed generators and loads. With the conventional droop control method, power contributions from DER converters cannot be accurately shared due to a mismatch of line impedances. In this paper, an augmented hierarchical control mechanism is proposed to solve the issues mentioned above. This hierarchical control mechanism consists of primary and secondary controllers. The primary stage utilized the droop controller to improve optimal power flow, mainly for the resistive network. The secondary stage is based on an improved methodology to compensate for the voltage and frequency variations during small and large signal disturbances. Moreover, the modelling and analysis for PMSG-based wind energy conversion systems are also presented. The response of the primary controller for the active and reactive power sharing is investigated. The analysis emphasizes the demonstration of optimal power-sharing under normal and abnormal conditions for the considered load. Finally, the suggested robust controller's performance is evaluated in MATLAB environment and simulation results show the proposed scheme's superiority under different operating conditions.

The main aim of this work is to present a step-by-step procedure to model and analyze the power loss distribution of three-level Gallium Nitride (GaN) inverters. It has been applied to three distinct three-phase three-levels voltage source inverters utilized in electric traction drives: Active Neutral Point Clamped, Neutral Point Clamped and T-Type Neutral Point Clamped. The proposed analytical power loss modelling, combined to an equivalent representation of the electrical machine demonstrated to be a viable solution to achieve a time-saving and low computational burden simulation platform, leading to satisfying accuracy results. This has been confirmed by comparing the results carried out from the simulations of a 110kW permanent magnet synchronous motor drive and those determined by considering a simplified circuital representation based on the proposed analytical power loss modelling.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Smart grids are seeing an increase in renewable energy and an enormous introduction of advanced power electronics, increasing the number of disturbance sources. This requires improving the accuracy of measurement systems capable of acquiring data for use in power system monitoring applications. Rogowski Coils (RCs) and Merging Units (MUs) are being widely deployed in controlling, metering, and monitoring of digital power systems. Because the performance of digital measurement devices has a direct influence on power measurement accuracy, it is critical to perform a laboratory calibration of these measurement instruments before they are installed in any project. To determine the magnitude and phase displacement errors of the RC+MU under normal and abnormal operating conditions, this article presents a comprehensive laboratory digital calibration system constructed from precise, readily available commercial products such as a fluxgate current transducer and a National Instrument. In addition, the analysis of measurement chain is affected by sources of uncertainty is discussed. The tests yield findings that are consistent with the relevant standards.

Thailand has formulated her climate change policy and updated relevant plans and policies to align with the goal of achieving carbon neutrality and net zero GHG emissions. This study investigates the optimal level of GHG mitigation in Thailand, taking into account the marginal abatement cost (MAC) and social cost of carbon (SCC). It evaluates how energy efficiency and renewable energy technologies influence GHG reduction in the power and industrial sector and illustrates policy recommendations that align with the 2020 to 2050 policy and plan period. The findings indicate that there may be instances where GHG mitigation potential is insufficient to reach the national mile-stone. In such cases, it becomes imperative to leverage all technologies within the marginal abatement cost curve (MACC) and also utilization of the social cost of carbon for policy decision making and meeting the desired goals. In certain scenarios, the adoption of additional technologies or measures may be necessary, such as flexible power generation and deploying carbon capture and storage or hydrogen which are high-cost technologies. Furthermore, preparations should be made for multiple levels of climate change policies and plans beyond 2030.

The paper proposes an innovative solution for managing and ensuring high energy efficiency of power supply systems at high non-linear loads. This is realized by maintaining optimal value of reliability indicators and high quality of power supply. The validation is carried out using analyzes and tests of quality of electromagnetic compatibility (EMC) for increased number of powered frequency converters. It has been proven that the effective use and reduction of energy consumption can be achieved thanks to the unique technological features of the employed electrical devices. This enables a normal operation of the system with decreased power and adequate control of energy processes. The problem of predicting power losses under changing conditions in a decentralized electrical network has been solved based on the theory of electromagnetic compatibility. The influence of the mains mode parameters and the indices of instantaneous distortion of current and voltage waveforms caused by the operation of converters on the resonance phenomena in power supply systems were investigated. Recommendations were developed for the selection of proper parameters of compensators for 6-10 kV and 0.4-0.66 kV circuits based on the analysis of the optimization problem when minimizing active power losses. Results of our findings may aid parties involved in designing and maintaining power networks in various applications, such as mines, etc.

Growing population, industrialization, and power requirements are adversely affecting the environment by increased greenhouse gases, resulting from fossil fuel burning. Global greenhouse gas mitigation targets have led the nations to promote clean and self-renewable sources of energy to address the environmental issue. Offshore wind power resources are relatively more attractive due to high winds, less turbulence, minimal visualization effects, and no interaction of infrastructure. The present study aims at conducting offshore wind power resources assessment (OWPRA) at some locations in the Gulf of North Suez. For this purpose, the long-term hourly mean wind speed (WS) and wind direction above means sea level (AMSL) and temperature and pressure data near surface is used. The data is obtained from ERA5 (fifth generation reanalysis for the global climate weather) at chosen six (L1-L6) offshore locations. The data covers a period of 43 years, between 1979 and 2021. The WS and direction are provided at 100 m AMSL while temperature and pressure are available near water surface level. At L1 to L6 locations, the log-term mean WS and wind power density (WPD) values are found to be 7.55 m/s and 370 W/m2, 6.37 m/s and 225 W/m2, 6.91 m/s and 281 W/m2, 5.48 m/s and 142 W/m2, 4.30 m/s and 77 W/m2, and 5.03 and 115 W/m2 and at 100 m AMSL; respectively. The higher magnitudes of monthly and annual windy site identifier indices (MWSI and AWSI) of 18.68 and 57.41 and 12.70 and 42.94 at L1 and L3 sites and generally lower values of wind variability indices are indicative of favourable winds source, which is also supported by higher magnitudes of mean WS, WPD, annual energy yields, plant capacity factors, and wind duration at these sites. The cost of energy, for the worst and the best cases are estimated as 10.120 USD/kWh and 1.274 USD/kWh at L5 and L1 sites corresponding to wind turbines WT1 and WT4. Based on the analysis, sites L1, L3, and L2 are recommended for wind farm development in order of preference. The wind variability and windy site identifiers indices introduced, will help decision-makers in deciding the potential windy sites with more confidence.

Over the past few years, there has been an increasing fascination with electric unmanned aerial vehicles (UAVs) because of their capacity to undertake demanding and perilous missions, while also delivering advantages in terms of flexibility, safety, and expenses. These UAVs are revolutionizing various public services, encompassing real-time surveillance, search and rescue operations, wildlife assessments, delivery services, wireless connectivity, and precise farming. To enhance their efficiency and duration, UAVs typically employ a hybrid power system. This system integrates diverse energy sources, such as fuel cells, batteries, solar cells, and supercapacitors. The selection of an appropriate hybrid power arrangement and the implementation of an effective energy management system are crucial for the successful functioning of advanced UAVs. This article specifically concentrates on UAV platforms powered by batteries, incorporating innovative technologies like in-flight recharging via laser beams and tethering. It provides an all-encompassing and evaluative examination of the current cutting-edge power supply configurations, with the objective of identifying deficiencies, presenting perspectives, and offering recommendations for future consideration in this domain.

Yaw misalignment can make a wake steer, which is an effective method to increase the power of wind farms, but it also increases the fatigue load of the turbines. In this paper, the method of combining yaw misalignment and pitch control (CYMP) is proposed to investigate the potential to mitigate wake interference, the wind velocity distribution and turbulence distribution in the wake, as well as the power and load changes of the wind turbine are studied, focusing on power in-crement and fatigue damage reduction. Although some studies have found that the method of CYMP are beneficial to increase power generation and reduce fatigue loads, there are no papers that have made a detailed analysis of the effects of wake turbulence, wind speed distribution, power, especially fatigue damage under this control. Simulation tool FAST.Farm is used to model and analyze wind farms, obtain the variation details of wake and provide simulation data for calculating power and fatigue load. The pitch control brings bias to the CYMP optimization results was neglected, the case studies show that the method of CYMP can reduce the fatigue load by 10.29% and increase the total power by 1.7% compared with only wake steering. The Model Predictive Control collaborative method based on CYMP is proposed, which can increase power by more than 2% and reduce thrust by more than 4% under 10m/s turbulent wind.

Accurately predicting the power of solar power generation can greatly reduce the impact of the randomness and volatility of power generation on the stability of the power grid system, which is beneficial for the balanced operation and optimized dispatch of the power grid system, and reduces operating costs. Solar PV power generation depends on weather conditions, which are prone to large fluctuations under different weather conditions. Its power generation is characterized by randomness, volatility and intermittency. Recently, the demand for further investigation and effective use on the uncertainty of short-term solar PV power generation prediction has been getting increasing attention in many application of renewable energy sources. In order to improve the predictive accuracy of output power of solar PV power generation and develop a precise predictive model, the authors worked predictive algorithms for the output power of a solar PV power generation system. Moreover, since short-term solar PV power forecasting is one of the important aspects for optimizing the operation and control of renewable energy systems and electricity markets, this review focuses on the predictive models of solar PV power generation, which can be verified in the daily planning and operation of a smart grid system. In addition, the predictive methods in the reviewed literature are classified according to the input data source used for accurate predictive models, and the case studies and examples proposed are analyzed in detail. The contributions, advantages and disadvantages of the predictive probabilistic methods are compared. Finally, the future studies of short-term solar PV power forecasting is proposed.

Electrical power quality is one of the main elements in power generation systems. At the same time, it is one of the most significant challenges regarding stability and reliability. Due to different switching devices in this type of architecture, different kinds of power generators, and non-linear loads are used for different industrial processes. As a result of this, the need to classify and analyze Power quality disturbance (PQD) to prevent and analyze the degradation of the system reliability affected by the non-linear and non-stationary oscillatory nature. This paper presents A Novel Mul-titasking Deep Neural Network (MDL) for the Classification and Analysis of Multiple Electrical Disturbances. The characteristics are extracted with a specialized and adaptive methodology for non-stationary signals, Empirical Mode Decomposition (EMD). The methodology’s design, devel-opment, and various performance tests are carried out with 28 different difficulty levels, such as severity, disturbance duration time, and noise in the 20 dB to 60 dB signal range. MDL was devel-oped with a diverse data set in difficulty and noise, with a quantity of 4500 records of different samples of multiple electrical disturbances. The analysis and classification methodology has an average accuracy percentage of 95% with multiple disturbances. In addition, an average accuracy percentage of 90% in analyzing important signal aspects for studying electrical power quality such as crest factor, Per Unit voltage analysis, Short Term Flicker Perceptibility (Pst), and Total Harmonic Distortion (THD), among others.

Lead-based ternary chalcogenide thin films of the (PbTe)1-x(PbS)x system were obtained by plasma-enhanced chemical vapor deposition technique (PECVD) under conditions of a nonequilibrium low-temperature argon plasma of an RF discharge (40.68 MHz) at a reduced pressure (0.01 Torr). High-purity elements were directly used as starting materials – Pb, S and Te. Plasma-chemical synthesis was carried out on the surface of of c-sapphire and silicon substrate. The physicochemical properties of the films were studied by various analytical methods. The dependence of the Seebeck coefficient, resistivity, and power factor on the structural properties and composition has been studied. The thermoelectric characteristics were found to be dependent on the film composition. Upon the selection of optimal sulfur concentration one can increase the power factor as compared to single phase PbS ot PbTe films.

The growing integration of renewable energy sources (RES) into the power system causes congestion to occur more frequently. In order to reduce congestion in the short term and to make the utilization of the power system more efficient in the long term, power flow control (PFC) in the transmission system has been proposed. However, exemplary studies show that congestion will increase also in the distribution system if the transmission system is expanded. For this reason, the potential of PFC to reduce congestion in a model of a real 110 kV distribution system is investigated. Several Unified Power Flow Controller (UPFC) devices are optimized in terms of their number and placement in the power system, their size, control parameters, and costs, by using a Parallel Tempering approach as well as a greedy algorithm. Two optimization variants are considered, one reducing the number of degrees of freedom by integrating system knowledge while the other is not. We find that near a critical grid state and disregarding costs, PFC can reduce congestion significantly (99.13 %). When costs of the UPFCs are taken into account, PFC can reduce congestion by 73.2 %. A basic economic analysis of the costs reveals that the usage of UPFCs is profitable. Furthermore, it is found that the reduction of the solution space of the optimization problem leads to better results faster and that, contrary to expectations, the optimization problem is simple to solve. The developed methods allow not only for the determination of the optimal use of UPFCs to minimize congestion, but also to estimate their profitability.

We investigate a family of nonlinear partial differential equations which are singularly perturbed in a complex parameter and singular in a complex time variable at the origin. These equations combine differential operators of Fuchsian type in time and space derivatives on horizontal strips in the complex plane with a nonlocal operator acting on the complex parameter known as the formal monodromy around 0. Their coefficients and forcing terms comprise polynomial and logarithmic type functions in time and are bounded holomorphic in space. A set of logarithmic type solutions are shaped by means of Laplace transforms relatively to time and parameter and Fourier integrals in space. Furthermore, a formal logarithmic type solution is modeled which represents the common asymptotic expansion of Gevrey type of the genuine solutions with respect to the complex parameter on bounded sectors at the origin.

Purpose – Extend the Blade Element Momentum Theory (BEMT) such that rotors with pronounced cone and axis angle (tilt or yaw) can be calculated. Derive an equation for the speed ratio (lambda) as a function of Tip Speed Ratio (TSR), radius, blade, cone and axis angle. This converts the BEMT into an Unsteady BEMT or UBEMT. Present the Wagner rotor as one such rotor geometry. --- Methodology – Literature review and calculations. --- Findings – The UBEMT can be used to calculate highly unconventional rotor geometries. --- Research Limitations – Although the aerodynamic coefficients used in the UBEMT are from measurements in steady flow conditions, they can be used with success. --- Practical Implications – Also conventional Horizontal Axis Wind Turbines (HAWT) with noticeable cone and axis angle should be calculated with the UBEMT. The accuracy of power calculations of these HAWTs can be slightly improved. --- Originality – Analytic equations for rotors with cone and axis angle have barely been discussed.

Integrating large-scale wind energy in modern power systems is demanding more efficient mathematical models to properly address classical assumptions in power system problems. In particular, there are two main assumptions in power system problems with wind integration that have not been adequately studied yet; First, non-linear AC power flow equations have been linearized in most of the literature. Such simplifications can lead to inaccurate power flow calculations that may result in other technical issues. Second, wind power uncertainties are inevitable and have been mostly modelled using the traditional uncertainty modelling approaches, that may not be suitable for large-scale wind power integration. In this paper, we address both challenges: we present a tight second-order conic relaxation (SOCR) for optimal power flow (OPF) problem, and simultaneously, implement the new effective budget of uncertainty approach for uncertainty modelling that determines the maximum wind power admissibility first and then addresses the uncertainty in the model. To the best of our knowledge, this is the first study that proposes an effective robust second-order conic programming (ERSOCP) model that simultaneously addresses the issues of power flow linearization and wind power uncertainty with the new paradigm on the budget of uncertainty approach. Our numerical results show the merit of the proposed model against traditional linearized power flow equations as well as traditional uncertainty modelling approaches.

Wireless power transfer promises to revolutionize the way we use and power mobile devices. However, low transfer efficiencies prevent this technology from seeing wide scale real-world adoption. The aim of this work is to use quasioptics to develop a system composed of a dielectric lens fed by a phased array to reduce spillover losses, increasing the beam efficiency, while working on the antenna system’s Fresnel zone. The DC-RF electronics, digital beamforming and beam-steering by an FPGA, and radiating 4x4 microstrip patch phased array have been developed and experimented upon, while the lens has been designed and simulated. This paper details these preliminary results, where the phased array radiation pattern was measured, showing that the beam is being generated and steered as expected, prompting the lens construction for the complete system experimentation.

Motivated for improving the efficiency and reliability of wind turbine energy conversion, this paper presents an advanced control design that enhances the power regulation efficiency and re-liability. The constrained behaviour of the wind turbine is taken into account, by using the barrier Lyapunov function in the analysis of the Lyapunov direct method. This, consequently, guarantees that the generated power remains within the desired bounds to satisfy the grid power demand. Moreover, a Nussbaum-type function is utilized in the control scheme, to cope with the unpre-dictable wind speed. This eliminates the need for accurate wind speed measurement or estimation. Furthermore, via properly designed adaptive laws, a robust actuator fault-tolerant capability is integrated into the scheme, handling the model uncertainty. Numerical simulations are performed on a high-fidelity wind turbine benchmark model, under different fault scenarios, to verify the effectiveness of the developed design. Also, a Monte-Carlo analysis is exploited for the evaluation of the reliability and robustness characteristics against the model-reality mismatch, measurement errors and disturbance effects.

The power-generation capacity of grid-connected photovoltaic (PV) power systems is increasing. As output power forecasting is required by electricity market participants and utility operators for the stable operation of power systems, several methods have been proposed using physical and statistical approaches for various time ranges. A short-term (30 min ahead) forecasting method has been previously proposed by our laboratory for geographically distributed PV systems using motion estimation. This study focuses on an important parameter for estimating the proposed motion and optimizing the parameter. This parameter is important because it is associated with the smoothness of the vector field, which is the result of motion estimation and influences the forecasting accuracy. In the periods with drastic power output changes, the evaluation was conducted on 101 PV systems located within a circle of 15-km radius in the Kanto region of Japan. The results indicate that the absolute mean error of the proposed method with the optimized parameter is 10.3%, whereas that of the persistent prediction method is 23.7%. Therefore, the proposed method is effective in forecasting for periods when PV output changes drastically in a short time.

The paper deals with the Compound Inverse Rayleigh distribution, shown to constitute a proper model for the characterization of the probability distribution of extreme values of wind-speed, a topic which is gaining growing interest in the field of renewable generation assessment, both in view of wind power production evaluation and the wind-tower mechanical reliability and safety. The first part of the paper illustrates such model starting from its origin as a generalization of the Inverse Rayleigh model - already proven to be a valid model for extreme wind-speeds - by means of a continuous mixture generated by a Gamma distribution on the scale parameter, which gives rise to its name. Moreover, its validity to interpret different field data is illustrated, also by means of numerous numerical examples based upon real wind speed measurements. Then, a novel Bayes approach for the estimation of such extreme wind-speed model is proposed. The method relies upon the assessment of prior information in a practical way, that should be easily available to system engineers. In practice, the method allows to express one’s prior beliefs both in terms of parameters, as customary, and/or in terms of probabilities. The results of a large set of numerical simulations – using typical values of wind-speed parameters - are reported to illustrate the efficiency and the accuracy of the proposed method. The validity of the approach is also verified in terms of its robustness with respect to significant differences compared to the assumed prior information.

We study the efficient computation of power indices for weighted voting games with precoalitions amongst subsets of players (reflecting, e.g., ideological proximity) using the paradigm of dynamic programming. Starting from the state-of-the-art algorithms for computing the Banzhaf and Shapley-Shubik indices for weighted voting games we present a framework for fast algorithms for the three most common power indices with precoalitions, i.e. the Owen index, the Banzhaf-Owen index and the Symmetric Coalitional Banzhaf index, and point out why our new algorithms are applicable for large numbers of players. We discuss implementations of our algorithms for the three power indices with precoalitions in C++ and review computing times as well as storage requirements.

The recent advancements in the field of communication have led data sharing to become an integral part of today's smart cities with the evolution of concepts such as the internet of vehicles (IoV) paradigm. As a part of IoV, Electric Vehicles (EVs) have recently gained momentum as authorities have started expanding their Low Emission Zones (LEZ) in an effort to build green cities with low carbon footprints. Energy is one of the key requirements of EVs not only to support the smooth and sustainable operation of EV itself but to also ensure connectivity between the vehicles and infrastructure with controlling devices like sensors and actuators installed within an EV. In this context, renewable energy sources (such as wind energy) dramatically play their parts in the automobile sector towards designing the energy harvesting electric vehicles (EH-EV) to pare the energy reliance on the national grid. In this article, a novel approach is presented to achieve electric generation due to vehicle mobility to support the communication primitives in electric vehicles which enables plenty of IoV use cases in the presence of surplus energy at hand. A small-scale wind turbine is designed to harness wind power for converting it into mechanical power. This power is then fed to the onboard DC generator to produce electrical energy. Furthermore, the acquired power is processed through a regulation circuitry to consequently achieve the desired power supply for the end load, i.e. the batteries installed. The suitable orientation for efficient power generation is proposed on ANSYS-based aerodynamics analysis. The voltages induced by DC generator at No-Load condition are 35V while at Full-Load 25V are generated at rated current of 6.9A, along with the generation of power at around 100W (at constant voltage) at the rated speed of 90 mph for nominal battery charging. Moreover, the acquired data can be monitored via an android application interface by using a Bluetooth module.

We analyzed the peak spring tidal current speeds, annual mean tidal power densities (TPD) and annual energy production (AEP) obtained from experiment 06.1, referred as the "HYCOM model" throughout, of the three dimensional (3D), global model HYCOM in an area covering the Baja California Pacific and the Gulf of California. The HYCOM model is forced with astronomical tides and surface winds alone, and therefore is particularly suitable to assess the tidal current and wind-driven current contribution to in-stream energy resources. We find two areas within the Gulf of California, one in the Great Island Region and one in the Upper Gulf of California, where peak spring tidal flows reach speeds of 1.1 meters per second. Second to fifth-generation tidal stream devices would be suitable for deployment in these two areas, which are very similar in terms of tidal in-stream energy resources. However, they are also very different in terms of sediment type and range in water depth, posing different challenges for in-stream technologies. The highest mean TPD value when excluding TPDs equal or less than 50 W/m² (corresponding to the minimum velocity threshold for energy production) is of 172.8 W/m², and is found near the town of San Felipe, at (lat lon) = (31.006 -114.64); here energy would be produced during 39.00% of the time. Finally, wind-driven currents contribute very little to the mean TPD and the total AEP. Therefore, the device, the grid, and any energy storage plans need to take into account the periodic tidal current fluctuations, for optimal exploitation of the resources.

Although different assessments and evaluations of Dual-Miller cycle performed, specified output power and thermal performance associated with engine determined. Besides, multi objective optimization of thermal efficiency, Ecological Coefficient of performance ( ) and Ecological function ( ) by the mean of NSGA-II technique and thermodynamic analysis performed. The Pareto optimal frontier obtaining the best optimum solution is chosen by fuzzy Bellman-Zadeh, LINMAP, and TOPSIS decision-making techniques. Based on the results, performances of dual-Miller cycles and their optimization are improved.

The Doubly-Fed Induction Generator (DFIG) has significant features in comparison with Fixed Speed Wind Turbine (FSWT), which has popularized its application in power system. Due to partial rated back-to-back converters in the DFIG, Fault Ride-Through (FRT) capability improvement is one of the great subjects regarding new grid code requirements. To enhance the FRT capability of the DFIG, many studies have been carried out. Fault current limiting devices as one of the techniques are utilized to limit the current level and protect switches of the back-to-back converter from over-current damage. In this paper, a review is done based on fault current limiting characteristic of the proposed fault current limiting devices Therefore, Fault Current Limiters (FCLs) and Series Dynamic Braking Resistors (SDBRs) are mainly taken into account. Operation of all configurations including their advantages and disadvantages is explained. Impedance type and the fault current limiting devices’ location are two important factors, which significantly affect the DFIG behaviour in the fault condition. These two factors are basically studied by the simulation and their effects on the key parameters of the DFIG are investigated. Finally, future works in respect to the FCL application in the FRT improvement of the DFIG have also been discussed.

In this paper we discuss a problem of generalization of binomial distributed triangle, that is sequence A287326 in OEIS. The main property of A287326 that it returns a perfect cube n as sum of n-th row terms over k; 0 ≤ k ≤ n−1 or 1 ≤ k ≤ n, by means of its symmetry. In this paper we have derived a similar triangles in order to receive powers m = 5; 7 as row items sum and generalized obtained results in order to receive every odd-powered monomial n^2m+1; m ≥ 0 as sum of row terms of corresponding triangle. In other words, in this manuscript are found and discussed the polynomials D_m(n,k) and U_m(n,k), such that, when being summed up over k in some range with respect to m and n returns the monomial n^2m+1.

This paper proposes the impact of plug-in electric vehicles integrated into power distribution system based on voltage dependent control. The plug-in electric vehicles was modeled as the static load model in power distribution systems under balanced load condition. The power flow analysis is determined by using the basic parameters of the electrical network. The main point of this study are compare with voltage magnitude profiles, load voltage deviation, and total power losses of the electrical power system. There are investigating the affected from constant power load, constant current load, constant impedance load and plug-in electric vehicles load, respectively. The IEEE 33 bus test system is used to test the proposed method by assigning each load type to a balanced load in steady state and applied the solving methodology based on the bus injection to branch injection matric, branch current to bus voltage matrix, and current injection matrix to solve the power flow problem. The simulation results showed that the plug-in electric vehicles load had the lowest impact compared to other loads. The lowest plug-in values for the electric vehicle loads were 0.062, 119.67 kW and 79.31 kVar for the load voltage deviation, total active power loss and total reactive power loss, respectively. Therefore, this study can be verified that the plug-in electric vehicles load were affected to the lowest of the electrical power system in condition to same sizing and position. So that, in condition to the plug-in electric vehicles load added into the electrical power system with the conventional load type or complex load type could be considered that the affected from the plug-in electric vehicles load in next study.

To implement renewable energy resources, microgrid systems have been adopted and developed into the technology of choice to assure mass electrification in the next decade. Microgrid systems have a number of advantages over the conventional utility grid systems, however, it faces severe instability issues due to continually increasing constant power loads. To improve the stability of the entire system, load side compensation technique is chosen because of its robustness and cost effectiveness. In this particular occasion, a sliding mode controller is developed for microgrid system in the presence of CPL to assure certain control objective of keeping the output voltage constant at 480V. After that, the robustness analysis of the sliding mode controller against parametric uncertainties is presented. The sliding mode controller robustness against parametric uncertainties, frequency variations, and additive white Gaussian noise (AWGN) are illustrated in this paper. Later, the performance of the PID and sliding Mode controller is compared in case of nonlinearity, parameter uncertainties, and noise rejection to justify the selection of Sliding Mode controller over PID controller. All the necessary calculations are reckoned mathematically and results are verified in the virtual platform such as MATLAB/Simulink with the appreciable outcome.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus 13 voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ 14 constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources 15 on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar 16 PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed 17 using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of 18 simulation and statistical results of EO with other optimization techniques showed that EO is more effective 19 and superior.

Heat stress due to climate warming can significantly affect the synthesis of sex hormones in male adolescents, which can impair the ability of the hypothalamus to secrete gonadotropin-releasing hormone on the hypothalamic-pituitary-gonadal axis, which leads to a decrease in luteinizing hormone and follicle-stimulating hormone, which ultimately negatively affects spermatogenesis and testosterone synthesis. For optimal spermatogenesis, the testicular temperature should be 2–6°C lower than body temperature. Heat stress directly affects the testes, damaging them and re-ducing testosterone synthesis. Additionally, chronic heat stress abnormally increases the level of aromatase in Leydig cells, which increases estradiol synthesis while decreasing testosterone, lead-ing to an imbalance of sex hormones and spermatogenesis failure. Low levels of testosterone in male adolescents lead to delayed puberty and incomplete sexual maturation, negatively affect height growth and bone mineral density, and can lead to a decrease in lean body mass and an in-crease in fat mass. In order for male adolescents to acquire healthy reproductive capacity, it is recommended to provide sufficient nutrition and energy, avoid exposure to heat stress, and pro-vide foods and supplements to prevent or repair testosterone reduction, germ cell damage, and sperm count reduction caused by heat stress so that they can enter a healthy adulthood.

The recent demand for reducing pollutant and CO2 emissions from internal combustion engines has created an urgent need for the development of ultra-lean burn engines that ensure combus-tion stability and reducing knocking tendency. One of the most promising methods is the Pre-chamber Spark Ignition (PCSI) system, where a jet of high-energy reactive gases, produced by pilot combustion in a pre-chamber, ignites the main combustion event in the cylinder. Given the intricate phenomena inherent to PCSI systems, conducting 3D CFD studies is imperative for a comprehensive analysis and optimal design. Furthermore, the detailed CFD model, combined with the calibrated 0-D/1-D model, is anticipated to yield a significant amount of new data that would be difficult to obtain through experimental approaches, making it essential for advancing our understanding and optimization of these systems. However, recently published papers re-port that some state-of-the-art models developed for conventional SI operation may not be pre-dictive under the challenging conditions of TJI systems, particularly under lean conditions. This review elucidates the reasons behind the widespread adoption of CFD in the optimal design of PCSI engines. It presents significant examples and delves into the potential and challenges of employing CFD not just as a predictive tool but also as a design instrument for enhancing PCSI engine performance.

Given the context of global climate change, a worldwide increase in land surface temperature (LST) is anticipated, leading to the exacerbation and broadening of its impacts. This could jeopardize the environmental conditions in countries with a predominantly hot and harsh climate, such as Bahrain, one of the Cooperation Countries (GCC) nations. Conversely, Bahrain is currently experiencing significant population growth, leading to a surge in demand for land to accommodate the construction of additional residential developments. This circumstance allows investigation of the potential impact of land use and land cover alterations on the variation in Land Surface Temperature (LST). In order to accomplish this objective, a residential development project was executed within the timeframe spanning from 2013 to 2023. Four sets of Landsat 8 OLI/TIRS remote sensing datasets were selected, with each set corresponding to one of the four climate seasons. Each set consisted of two images: one capturing the study area before the commencement of the development process and the other depicting the study area after the completion of the development. The study area was analyzed by extracting the land surface temperature (LST), normalized difference vegetation index (NDVI), and normalized difference built-up index (NDBI) on various dates. Subsequently, correlation and regression analysis were employed to examine the interrelationships among these three variables. The findings demonstrated a notable rise in the mean land surface temperature throughout the spring and autumn seasons following the conclusion of land development activities. The findings indicate a positive and robust association between LST and NDBI across all seasons. Moreover, this relationship strengthened following the completion of development activities in the area. Conversely, there was a negative correlation between LST and NDVI prior to the region's development, which transformed into a positive relationship post-development. These results provide empirical support for the notion that small-scale residential developments contribute to a notable increase in LST, primarily driven by the expansion of impervious surfaces in built-up areas. The findings can potentially contribute to the formulation of localized adaptation strategies for small-scale residential development projects.

Triangles are an ever present feature in nature, which the building construction industry duly echoes. However, an exact expression intended to offer the radiant field due to any triangle in an upright or inclined position had not been identified by previous research. In this case, the author has been able to solve by direct integration, the canonical expression of radiative transfer. This result alone confers a myriad of possibilities that had been inconceivable before, for studying in detail the three-dimensional heat transfer behavior of volumes and figures in which triangles do manifest, such as fins, windows, roof-gables and louvers of various kinds. Typically, shading devices, when tilted, give rise in their extremes to rhomboidal shapes which were difficult to take into account or had to be subject to discretization and subsequent Monte Carlo methods in order to perform an approximate calculation of their emission. This implied a lengthy and inexact procedure that induced many errors and consumed computing time. We can now avoid all the former downsides due to the advances hereby presented. As the novel expression can be converted into an algorithm it will be advantageously employed for simulation. This significant finding dovetails in the intricate puzzle of radiated heat and we believe that their consequences will greatly affect the conception and design of HVAC devices, aircraft manufacturing and specifically building or lighting industries among others.

Climate change-induced temperature fluctuations pose a significant threat to crop production, particularly in the Southern Hemisphere. This study investigates the transcriptome and physiological responses of rapeseed to post-flowering temperature increases, providing valuable insights into the molecular mechanisms underlying rapeseed tolerance to heat stress. Two rapeseed genotypes, Lumen and Solar, were assessed under control and heat stress conditions in field experiments conducted in Valdivia, Chile. Results showed that seed yield and seed number were negatively affected by heat stress, with genotype-specific responses. Lumen exhibited a 9.3% average seed yield reduction, while Solar showed a 28.7% reduction. RNA-seq analysis of siliques and seeds revealed tissue-specific responses to heat stress, with siliques being more sensitive to temperature stress. Hierarchical clustering analysis identified distinct gene clusters reflecting different aspects of heat stress adaptation in siliques, with a role for protein folding in maintaining silique development and seed quality under high temperature conditions. In seeds, three distinct patterns of heat-responsive gene expression were observed, with genes involved in protein folding and response to heat showing genotype-specific expression. Gene coexpression network analysis revealed major modules for rapeseed yield and quality, as well as the trade-off between seed number and seed weight. Overall, this study contributes to understanding the molecular mechanisms underlying rapeseed tolerance to heat stress and can inform crop improvement strategies targeting yield optimization under changing environmental conditions.

The DNS of film boiling requires strong computational resources that are difficult to obtain for a daily CFD use by the practitioners of the industrial R&D experts. On the other hand, the film boiling experiments are associated with the usage of the expensive and highly sophisticated apparatus, and the research to this end is found to be relatively difficult due to high heat flow rates that are present in the process itself. When combined with a transient heat conduction in a solid, the problem becomes significantly difficult. Therefore, a novel method in computation of conjugate heat transfer during film boiling in a quiescent liquid has been proposed in this paper. The method relies on the solution of mass, momentum and energy conservation equations in a two-fluid framework, supplemented with the appropriate closures. Furthermore, the turbulent flow has been found as an important parameter in obtaining the accurate solution of the temperature field evolution in a solid specimen, via the proper modeling of turbulent kinetic energy (TKE) value, that has been imposed as a constant value, i.e., the frozen turbulence approach. It was found, in addition, that the appropriate TKE value can be obtained by use of Kelvin-Helmholtz instability theory in conjunction with the boundary layer theory. The obtained results show excellent agreement with the experimental data within the first 15 s of the experiment, i.e., the first ca. 10 % of the total duration of the film boiling mode of heat transfer. Furthermore, the heat transfer coefficient has matched the error bands prescribed by the authors of the paper that has presented the correlations, whilst the averaged values are far beyond this band, i.e., are slightly more than 30 % higher. The further inspection has revealed a measure of similarity between the computational result of the volume fraction field distribution and the experiment, thus confirming the capability of the method to obtain realistic interface evolution in time. The method has shown full capability for further pursuing the industrial-scale film boiling problems that involve turbulent flow and the conjugate heat transfer approach.

In this study, we focus on the effects of fuel bed representation and fire heat and smoke distribution in a coupled fire-atmosphere simulation platform for two landscape-scale fires: the 2018 Camp Fire and the 2021 Caldor Fire. The fuel bed representation in the coupled fire-atmosphere simulation platform WRF-Fire currently includes only surface fuels. Thus, we enhance the model by adding canopy fuel characteristics and heat release, for which a method to calculate the heat generated from canopy fuel consumption is developed and implemented in WRF-Fire. Furthermore, the current WRF-Fire heat and smoke distribution in the atmosphere is replaced with a heat-conserving Truncated Gaussian (TG) function and its effects are evaluated. The simulated fire perimeters of case studies are validated against semi-continuous, high-resolution fire perimeters derived from NEXRAD radar observations. Furthermore, simulated plumes of the two fire cases are compared to NEXRAD radar reflectivity observations followed by buoyancy analysis using simulated temperature and vertical velocity fields. The results show that while the improved fuel bed and the TG heat release scheme have small effects on the simulated fire perimeters of the wind-driven Camp Fire, they affect the propagation direction of the plume-driven Caldor Fire, leading to better-matching fire perimeters with the observations. However, the improved fuel bed representation together with the TG heat smoke release scheme leads to more realistic plume structure in comparison to the observations in both fires. The buoyancy analysis also depicts more realistic fire-induced temperature anomalies and atmospheric circulation when the fuel bed is improved.

Energy efficiency is, in principle, a simple idea: an output of human value, for example, vehicle-km traveled, divided by the needed input energy. Efficiency improvements are regarded by many as an important means of mitigating not only climate change, but also other environmental problems. Accordingly, many countries have efficiency ratings for appliances and efficiency standards for road vehicles. Despite the vast number of articles published on energy efficiency, few question whether it is a useful or accurate measure in its present form. This review addresses this lack, by a critical review of the literature, not only in energy efficiency, but in other areas of research, such as ‘energy services’, that can help broaden the scope of this idea, both geographically and conceptually. These shortcomings are illustrated in case studies of road passenger transport and buildings. The main findings are that energy efficiency inevitably has an ethical dimension, that feedbacks are more widespread than generally considered, and that conventional efficiency measures omit important energy input items, particularly those concerned with mining of the materials needed for renewable energy plants. Finally, the key results of this review are summarized, and its limitations are discussed, as is the future research needed to overcome these shortcomings.

The behavior of convective boundary conditions is studied to delineate their role in heat and mass relegation in the presence of radiation, chemical reaction, and hydromagnetic forces in three-dimensional Powell-Eyring nanofluids. Implications concerning non-Fourier’s heat flux and non-Fick’s mass flux with respect to temperature nanoparticle concentration were examined to discuss the graphical attributes of the principal parameters. An efficient optimal homotopy analysis method is used to solve the transformed partial differential equations. Tables and graphs are physically interpreted for significant parameters

Tumor cells exhibit a resistance-associated secretory phenotype involving extracellular vesicles (EVs) and heat shock proteins (HSPs). This response occurs in response to cell stress and cancer therapeutics. HSPs are stress-responsive molecular chaperones promoting proper protein folding, while also being released from cells with EVs as well as in free form as alarmins. We have here investigated the secretory phenotype of castration-resistant prostate cancer (CRPC) cells using proteome analysis. We have also examined the roles of the key co-chaperone CDC37 in stressome release, epithelial-to-mesenchymal transition (EMT), and tumor progression. A number of HSP family members and their common receptor CD91/LRP1 were enriched at high levels in CRPC cell-derived EVs among over 700 other protein species. The small EVs (30 to 200 nm in size, potentially exosomes) were released even in a non-heated condition from the prostate cancer cells, whereas EMT-coupled release of EVs (200 to 500 nm, likely ectosomes) with associated HSP90α was increased after heat shock stress (HSS). Lactate dehydrogenase, a marker of membrane leakage/damage of cells, was also released upon HSS from the prostate cancer cells. During this stress response, intracellular CDC37 was also transcriptionally inducible by heat shock factor 1, and knockdown of CDC37 decreased EMT-coupled release of EVs. Triple knockdown of CDC37, HSP90α, and HSP90β was required for efficient reduction of the chaperone trio and to reduce tumorigenicity of the CRPC cells in vivo. Taken together, the data indicated that CDC37 and HSP90 are essential for stressome release and for tumorigenesis in resistant cancer.

Plants thriving in desert environments are suitable for studying mechanisms for plant survival under extreme seasonal climate variation. Zygophyllum dumosum Boiss, like many other Zygophyllaceae species, displays a unique epigenetic mechanism whereby the repressive markers di- and tri-methyl of H3K9 do not exist. We studied epigenetic mechanisms underlying seasonal growth cycles in Z. dumosum and their association with factors regulating basic cell functions. We showed strong association between rainfall and seasonal growth and the epigenetic marker of dimethyl H3K4, which disappears on entry into the dry season and the acquisition of dormant state. DNA methylation is not affected by lack of H3K9 di and tri methyl and changes in methylation pattern are apparent on entry into the dry season. Proteome analysis of acid soluble fractions revealed extensive reduction in ribosomal proteins and in proteins involved in chloroplasts and mitochondria activities during the dry seasons concomitantly with up-regulation of molecular chaperone HSPs. Our results highlight mechanisms underlying Z. dumosum adaptation to seasonal climate variation. Particularly, summer dormancy is associated with loss of the permissive epigenetic marker dimethyl H3K4, which might facilitate genome compaction, concomitantly with significant reduction in proteins involved in basic cell functions (i.e., protein synthesis, photosynthesis and respiration).

The aim of this research work consisted of assessing the effects of the COVID-19 pandemic on the interurban public transport system in a rural region with a sparse population density, considering the number of tickets sold and passengers in each locality, as well as the different connecting lines. From a methodological point of view and with the intention of identifying patterns to explain the behaviour of both routes and passengers, a series of variables were selected, becoming determining factors that sought to offer a solution to the search for a common trend. Additionally, data processing by means of statistical analysis and the application of Geographic Information Systems (GIS) tools complemented the procedure. The results obtained in the investigation were provided both by municipality and by interurban route. An interesting finding of the research was the uneven recovery of the municipalities. The localities closest to the attractor nucleus have recovered more quickly to pre-pandemic mobility levels due to their geographical proximity, larger population, higher income per household and the need to access certain public services. In terms of routes, all lines showed significant decreases in ticket sales, although with variations. Although passenger numbers have shown a gradual recovery, the initial loss was considerable, and pre-pandemic normality has not been completely achieved. The authors consider that future research should include other alternative means of transport in these interurban areas, incorporating variables to characterise passengers, such as age, gender...etc.

A “watch and wait” strategy, delaying treatment until active disease manifests, is adopted for most CLL cases; however prognostic models incorporating biomarkers have shown to be useful to predict treatment requirement. In our prospective O-CLL1 study including 224 patients, we investigated the predictive role of 513 microRNAs (miRNAs) on time to first treatment (TTFT). In the context of this study six well-established variables (i.e., Rai stage, beta-2-microglobulin levels, IGVH mutational status, del11q, del17p, and NOTCH1 mutations) maintained significant associations with TTFT in a basic multivariable model, collectively yielding a Harrell's C-index of 75% and explaining 45.4% of the variance in the prediction of TTFT. Concerning miRNAs, 73 out of 513 were significantly associated with TTFT in a univariable model; of these, 16 retained an in-dependent relationship with the outcome in a multivariable analysis. For 8 of these (i.e., miR-582-3p, miR-33a-3p, miR-516a-5p, miR-99a-5p, and miR-296-3p, miR-502-5p, miR-625-5p, and miR-29c-3p) a lower expression correlated with a shorter TTFT, whereas in the remaining eight (i.e., miR-150-5p, miR-148a-3p, miR-28-5p, miR-144-5p, miR-671-5p, miR-1-3p, miR-193a-3p, and miR-124-3p) the higher expression was associated with shorter TTFT. Integrating these miRNAs into the basic model significantly enhanced predictive accuracy, raising the Harrell’C index to 81.1% and the explained variation in TTFT to 63.3%. Moreover, the inclusion of the miRNA scores enhanced the Integrated Discrimination Improvement (IDI) and the Net Reclassification Index (NRI), underscoring the potential of miRNAs to refine CLL prognostic models and providing insights for clinical decision-making. In silico analyses on the differently expressed miRNAs revealed their potential regulatory functions of several pathways, including those involved in the therapeutic responses. To add a bio-logical context to the clinical evidence, a miRNA-mRNA correlation analysis revealed at least one significant negative correlation between 15 of the identified miRNAs and a set of 50 Artificial Intelligence (AI) selected genes, previously identified by us as relevant for TTFT prediction in the same cohort of CLL patients. In conclusion, the identification of specific miRNAs as predictors of TTFT holds promise for enhancing risk stratification in CLL to predict therapeutic needs. However, further validation studies and in-depth functional analyses are required to confirm the robustness of these observations and to facilitate their translation into meaningful clinical utility.

Concurrent Optical and Magnetic Stimulation (COMS) combines extremely low frequency electromagnetic and light stimulation modalities for enhanced wound healing. In this report, we investigated the potential mechanistic synergism between magnetic and light components by comparing their individual and combined cellular responses. Although each individual stimulation mode was capable of stimulating cell proliferation, magnetic fields exposure alone produced greater proliferation enhancement than light alone, yet their combined effects of were supra-additive of the individual responses. Reactive oxygen species were incrementally reduced by exposure to light, magnetics fields and their combination, where statistical significance was ultimately achieved. On the other hand, ATP production was significantly enhanced in response to magnetic exposure alone or in combination with light. These results suggest that mitochondrial respiratory efficiency was preferentially improved by the combination of the two stimuli. Protein expression related to cell proliferation was preferentially enhanced by the combinatory COMS modality as were the protein levels of the TRPC1 cation channel previously implicated as part of a calcium-mitochondrial signaling axis invoked by electromagnetic exposure and involved in proliferation. These results corroborate that light facilitates functional synergism with magnetic fields that ultimately impinge on mitochondria-dependent developmental responses. The aminoglycoside antibiotics (AGAs) have been previously shown to antagonize TRPC1-mediated magnetotransduction. Streptomycin applied during the exposure to any of the stimulation modes reduced proliferation enhancement, whereas streptomycin added after the exposure did not. Notably, the COMS modality and magnetic field exposure were capable of partially overcoming streptomycin antagonism of proliferation, whereas light alone was not. Transductional antagonism of combinatorial photon-electromagnetic effects by streptomycin thus aligns with previous studies showing that the AGAs block TRPC1-mediated magnetotransduction when applied during exposure. The prophylactic usage of the AGAs (neomycin) should be avoided during COMS therapy to maintain clinical efficacy and would be a common concern with most other electromagnetic regenerative paradigms.

Breast cancer is the most common cause of mortality due to cancer for woman both in Lithuania and worldwide. Chances of survival after diagnosis differ significantly depending on the stage of disease at the time of diagnosis and other factors. One way to estimate survival is to construct a Kaplan-Meier estimate for each factor value separately. However, in cases when it is impossible to observe a large number of patients (for example, in case of countries with lower numbers of inhabitants) dividing data into subsets, say, by stage at diagnosis may lead to results where some subsets contain too little data so that results of Kaplan Meier (or any other) method will become statistically incredible. The problem may become even more acute if the researcher would like to use more risk factors, such as stage at diagnosis, sex, place of living, treatment method, etc. Alternatively, Cox models are used to analyse survival data with covariates, and they don’t require dividing the data into subsets according to chosen risks factors (hazards).

Sums of M consecutive squared integers (a+i)^2 equaling squared integers (for a<=1, 0<= i<= M-1) yield remarkable regular linear features when plotting values of M in function of a. These features correspond to groupings of pairs of a values for successive same values of M around straight lines of equation mu*M = 2a and are characterized in this paper for rational values of mu.

The main channel for disseminating information is now the Internet. Users have different expectations for the calibre of websites regarding the posted and presented content. The WEB site's quality is influenced by up to 120 factors, each represented by two to fifteen attributes. A major challenge is quantifying the features and evaluating the quality of a website based on the feature counts. One of the aspects that determines a website's quality is its completeness, which focuses on the existence of all the objects and their connections with one another. It isn’t easy to build an expert model based on feature counts to evaluate website quality, so this paper has focused on that challenge. Both a methodology for calculating a website's quality and a parser-based approach for measuring feature counts are offered. We provide a multi-layer perceptron model that is an expert model for forecasting website quality from the "Completeness" perspective. The accuracy of the predictions is 98%, whilst the accuracy of the nearest model is 87%.

Low-sodium salt substitute (LSSS) has the potential in regulating sodium and potassium intake and has been available in China market for years. However, its real-world use and impact to sodium\potassium intake is unclear. Baseline data of 4000 adult participants who participated in three similar-designed randomized controlled trails were pooled together for this study. Self-reported awareness and use of LSSS were collected using the uniform questionnaire, and the 24-h urinary sodium and potassium excretion was used to estimate their dietary intake. Mixed-effects models were developed to assess the relationship between LSSS and 24-h urinary sodium and potassium excretion. 32.0% of the participants reported awareness of LSSS and 11.7% reported its current use. After adjusting location, sex, age, and education, compared with the group of participants unaware of LSSS, participants who were aware but not using LSSS and those who were using LSSS had a lower 24-h urinary sodium excretion by –356.1(95% CI: –503.9, –205.9) mg/d and –490.6(95% CI: –679.2, –293.7), respectively (p&lt;0.001). No significant difference was found for 24-h urinary potassium excretion and sodium-to-potassium ratio among the three groups (p&gt;0.05). In conclusion, although associated with lower sodium intake, the awareness and real-world use of LSSS are still very low in China.

As in every workplace, human sustainability in dental enterprises is connected to air and water quality, eco-friendly and naturally designed working spaces and 4R’s culture. Purpose of this study is to access the preferences and knowledge on circular economy and green building construction in a sample of students and dentists in Greece. Students (N1=93) and dentists (N2= 126) filled in e-questionnaires from April to December 2022. The response rate was 17,88% for N1 and 1.94% for N2. Data revealed that both students and dentists lack knowledge on circular economy (N1=67.7%, N2=68,25%), EU regulations on amalgam disposal (N1=64.5%, N2=58.73%) and plastic recycling (N1=76.34%, N2=76,98) while they do recycle at home (N1= 80.6%, N2=82.54%) and have participated in voluntary environmental actions (N1=58.1%, N2=66.67%). Gender influences the importance of factors related to green dental practices, with women students being more prone to answer positively as important for increase costs for network changes (p=0.02), lack of environmental awareness of manufacturers (p=0.057), and poor wastewater management (p=0.01). Students from urban areas are more prone to answer positively for lack of state financial support (p=0.02), low level of green design in the building (p=0.03), low direct financial benefit of a green dental office (p=0.04), low benefit to the reputation of the green dental office (p=0.02), lack of continuing education training seminars on green dentistry (p=0.05). For dentists, no significant relationships were observed except of a weak positive relationship in increase in costs for changes related to utility networks (p=0.08) while increased wasteful energy (p=0.12) and waste of dental materials (p=0.19) seemed important only for dentists in urban areas. Women dentists were more prone to answer positively on wasting energy (p=0.024) and use of unapproved disinfection products (p=0.036). The findings contribute ideas and solutions on green dental office buildings and sustainable behaviors through educational activities and social perspective of factors such as age, experience in dentistry, gender, and urbanism. It also inspires future multi-disciplinary research on dental quality assurance, psychology of environmentalism, economics, and behavioral science in dentistry.

Invasive weeds cause significant crop yield and economic losses in agriculture. The highest in-direct impact may be attributed to the role of invasive weeds as virus reservoirs especially within the commercial growing areas. The new tobamovirus tomato brown rugose fruit virus (ToBRFV), recently identified in the Middle-East, overcomes the Tm-22 resistance allele in the cultivated tomato varieties grown in greenhouses. In this study, we determined the role of invasive weed species as potential hosts for ToBRFV and pepino mosaic virus (PepMV). Out of all tested weed species, the invasive species So-lanum elaeagnifolium and S. rostratum, mechanically inoculated with ToBRFV, were positive for To-BRFV in both enzyme linked immunosorbent assay (ELISA) and RT-PCR tests. S. rostratum was also positive for PepMV. No conspicuous phenotype was observed on ToBRFV infected S. elaeagnifolium plants suggesting a hostplant associated defense response. S. rostratum plants inoculated with either ToBRFV alone or a mixture of ToBRFV and PepMV-IL, contained high ToBRFV levels. In addition, when inoculated with ToBRFV or PepMV-IL disease symptom manifestations were observed in S. rostratum plants and the symptoms were exacerbated upon mixed infections with both viruses. The distribution and abundance of both Solanaceae species increase the risks of virus transmission between species.

Immune escape is observed with SARS-CoV-2 Omicron (Pango lineage B.1.1.529), the predominant circulating strain worldwide. Booster dose was shown to restore immunity against Omicron infection, however, real world data comparing mRNA (BNT162b2; Comirnaty) and inactivated vaccine (CoronaVac; Sinovac) homologous and heterologous boosting is lacking. A retrospective study was performed to compare the rate and outcome of COVID-19 in healthcare workers (HCWs) with various vaccination regime during a territory-wide Omicron outbreak in Hong Kong. During the study period 1 Feb – 31 Mar 2022, 3167 HCWs were recruited, 871 HCWs reported 746 and 183 episodes of significant household and non-household close contact. 737 HCWs acquired COVID-19 which were all clinically mild. Time dependent Cox regression showed that, comparing with 2-dose vaccination, 3-dose vaccination reduced infection risk by 31.7% and 89.3% in household contact and non-household close contact respectively. Using 2-dose BNT162b2 as reference, 2-dose CoronaVac recipient had significantly higher risk of being infected (HR 1.69 P<0.0001). Three-dose BNT162b2 (HR 0.4778 P<0.0001) and 2-dose CoronaVac + BNT162b2 booster (HR 0.4862 P=0.0157) were associated with lower risk of infection. Three-dose CoronaVac and 2-dose BNT162b2 + CoronaVac booster were not significantly different from 2-dose BNT162b2. The mean time to achieve negative RT-PCR or E gene cycle threshold 31 or above was not affected by age, number of vaccine dose taken, vaccine type and timing of the last dose. In summary, we have demonstrated lower risk of breakthrough SARS-CoV-2 infection in HCWs given BNT162b2 as booster after 2 doses of BNT162b2 or CoronaVac.

The option of decarbonizing urban freight transport using Battery Electric Vehicle (BEV) seems promising.However, there is currently a strong debate whether Fuel Cell Electric Vehicle (FCEV) might be the bettersolution. The question arises as to how a fleet of FCEV influences the operating cost, the Greenhouse Gas(GHG) emissions and primary energy demand in comparison to BEVs and to Internal Combustion EngineVehicle (ICEV). To investigate this, we simulate the urban food retailing as a representative share of urbanfreight transport using a multi-agent transport simulation software. Synthetic routes as well as fleet size andcomposition are determined by solving a Vehicle Routing Problem (VRP). We compute the operating costsusing a total cost of ownership (Total Cost of Ownership (TCO)) analysis and the use phase emissions as wellas primary energy demand using the Well To Wheel (WTW) approach. While a change to BEV results in 17 -23% higher costs compared to ICEV, using FCEVs leads to 22 - 57% higher costs. Assuming today’s electricitymix, we show a GHG emission reduction of 25% compared to the ICEV base case when using BEV. Currenthydrogen production leads to a GHG reduction of 33% when using FCEV which however cannot be scaled tolarger fleets. Using current electricity in electrolysis will increase GHG emission by 60% compared to the basecase. Assuming 100% renewable electricity for charging and hydrogen production, the reduction from FCEVsrises to 73% and from BEV to 92%. The primary energy requirement for BEV is in all cases lower and forhigher compared to the base case. We conclude that while FCEV have a slightly higher GHG savings potentialwith current hydrogen, BEV are the favored technology for urban freight transport from an economic andecological point of view, considering the increasing shares of renewable energies in the grid mix.

The importance of this study may be defined by using the smart techniques to earned value indicators of residential buildings projects in Republic of Iraq, only one development intelligent forecasting model was presented to predict Schedule Performance Index (SPI), Cost Performance Index (CPI), and To Complete Cost Performance Indicator (TCPI) are defined as the dependent. The approach is principally influenced by the determining numerous factors which effect on the earned value management, that involves Iraqi historical data. In addition, six independent variables (F1: BAC, Budget at Completion., F2: AC, Actual Cost., F3, A%, Actual Percentage., F4: EV, Earned Value. F5: P%, Planning Percentage., and F6: PV, Planning Value) were arbitrarily designated and satisfactorily described for per construction project. It was found that ANN has the capability to envisage the dust storm with a great accuracy. The correlation coefficient (R) has been 90.00%, and typical accuracy percentage has been 89.00%.

This paper presents an overview of the smart electro-clothing systems (SeCSs) targeted at health monitoring, sports benefits, fitness tracking, and social activities. Technical features of the available SeCSs, covering both textile and electronic components, are thoroughly discussed and their applications in the industry and research purposes have been highlighted. In addition, it also presents the developments in the associated areas of wearable sensor systems and textile-based dry sensors. As it became evident during the literature research, such a review on SeCSs covering all relevant issues has not been presented before. This paper will be particularly helpful for new generation researchers investigating the design, development, function and comforts of the sensor integrated clothing materials.

Over the past few decades, the growth of the urban population has been remarkable. Nowadays, 50% of the population lives in urban areas, and forecasts point that by 2050 this number will reach 70%. Today, 64% of all travel made is within urban environments and the total amount of urban kilometers traveled is expected to triple by 2050. Thus, seeking novel solutions for urban mobility becomes paramount for 21st century society. In this work, we discuss the performance of vehicular networks. We consider the metric Delta Network. The Delta Network characterizes the connectivity of the vehicular network through the percentage of travel time in which vehicles are connected to roadside units. This article reviews the concept of Delta Network and extends its study through the presentation of a general heuristic based on the definition of scores to identify the areas of the road network that should receive coverage. After defining the general heuristic, we show how small changes in the score computation can generate very distinct (and interesting) patterns of coverage, each one suited to a given scenario. In order to exemplify such behavior, we propose three deployment strategies based on simply changing the computation of scores. The results show that the strategies derived from the general heuristic are very interesting, all of them deploying roadside units in a circle pattern around the traffic epicenter.

Increased nutrient withdrawal by rapidly expanding intensive cropping systems, in combination with imbalanced fertilization, is leading to potassium (K) depletion from agricultural soils in Asia. There is an urgent need to better understand the soil K-supplying capacity and K-use efficiency of crops to address this issue. Maize is increasingly being grown in rice-based systems in South Asia, particularly in Bangladesh and North East India. The high nutrient extraction, especially K, however, causes concerns for the sustainability of maize production systems in the region. The present study was designed to estimate, through a plant-based method, the magnitude, and variation in K-supplying capacity of a range of soils from the maize-growing areas and the K-use efficiency of maize in Bangladesh. Eighteen diverse soils were collected from several upazillas (or sub-districts) under 11 agro-ecological zones to examine their K-supplying capacity from the soil reserves and from K fertilization (@ 100 mg K kg-1 soil) for successive seven maize crops grown up to V10-V12 in pots inside a net house. A validation field experiment was conducted with five levels of K (0, 40, 80, 120 and 160 kg ha-1) and two fertilizer recommendations based on “Nutrient Expert for Maize-NEM” and “Maize Crop Manager-MCM” decision support tools (DSSs) in 12 farmers’ fields in Rangpur, Rajshahi and Comilla districts in Bangladesh. Grain yield and yield attributes of maize responded significantly (P < 0.001) to K fertilizer, with grain yield increase from 18 to 79% over control in all locations. Total K uptake by plants not receiving K fertilizer, considered as potential K-supplying capacity of the soil in the pot experiment, followed the order: Modhukhali >Mithapukur >Rangpur Sadar >Dinajpur Sadar >Jhinaidah Sadar >Gangachara >Binerpota >Tarash >Gopalpur >Daudkandi >Paba >Modhupur >Nawabganj Sadar >Shibganj >Birganj >Godagari >Barura >Durgapur. Likewise in the validation field experiment, the K-supplying capacity of soils was 83.5, 60.5 and 57.2 kg ha-1 in Rangpur, Rajshahi, and Comilla, respectively. Further, the order of K-supplying capacity for three sites was similar to the results from pot study confirming the applicability of results to other soils and maize-growing areas in Bangladesh and similar soils and areas across South Asia. Based on the results from pot and field experiments, we conclude that the site-specific K management using the fertilizer DSSs can be the better and more efficient K management strategy for maize.

This paper deals with the environmental characterization of a large and densely populated area, with a poor reputation for contamination, considering the contribution of environmental features (air, soil, soil hydraulic and groundwater) and the potential effects on human health. The use of Geographic Information System (GIS) has made possible a georeferenced inventory and, by overlaying environmental information, an operational synthesis of comprehensive environmental conditions. The cumulative effects on environmental features were evaluated, taking into account superposition effects, by means of the spatial multicriteria decision analysis (S-MCDA). The application of the S-MCDA for converging the combination of heterogeneous factors, related to soil, land and water, deeply studied by heterogeneous groups of experts, constitutes the novelty of the paper. The results confirmed an overall higher potential of exposure to contaminants in the environment and higher mortality rates in the study area for some tumours, but hospital admissions for tumours were generally similar to the regional trend. Besides, mortality data may be strictly dependent on the poor socioeconomic conditions, quality of therapy and a lack of welfare in the area relative to the rest of Italy. Finally, as regards the possible relationship between presence of contaminants in the environment and health conditions of the population no definite conclusions can be drawn, although the present study encourages the use of the new proposed methods, that increase the possibilities for studying the combined effect of more environmental factors.

Intracellular aggregates of the alpha-synuclein protein result in cell loss and dysfunction in Parkinson’s disease and atypical parkinsonism, such as multiple system atrophy and dementia with Lewy bodies. Each of these neurodegenerative conditions, known collectively as alpha-synucleinopathies, may be characterized by a different suite of molecular triggers that initiate pathogenesis. The mechanisms whereby alpha-synuclein aggregates in turn mediate cytotoxicity also remain to be fully elucidated. However, recent studies have implicated the cell-to-cell spread of alpha-synuclein as the major mode of disease propagation between brain regions during disease progression. Here, we review the current evidence for different modes of alpha-synuclein cellular release, movement and uptake, including exocytosis, exosomes, tunnelling nanotubes, glymphatic flow and endocytosis. A more detailed understanding of the major modes by which alpha-synuclein pathology spreads throughout the brain may provide new targets for therapies that halt the progression of disease.

The COVID-19 pandemic has significantly reshaped global power dynamics, impacting economies, political landscapes, international relations, and technological advancements. Historically, pandemics have acted as catalysts for social and economic transformations, and COVID-19 has followed this pattern by intensifying existing trends and creating new opportunities for power shifts. Economically, the pandemic led to unprecedented disruptions, with East Asian countries demonstrating greater resilience and adaptability compared to Western economies. This has resulted in notable economic power shifts, particularly benefiting China, which experienced a swift recovery. Politically, the pandemic exacerbated geopolitical tensions, notably between the United States and China, while also fostering new forms of international cooperation, such as vaccine diplomacy and multilateral health initiatives. Technologically, the pandemic accelerated digital transformation and innovation in biotechnology, with significant advancements in healthcare systems. Socially, it exposed and exacerbated inequalities, prompting discussions on social justice and healthcare reforms. Environmentally, short-term improvements were observed, but the need for sustainable development and green recovery strategies became evident. This article examines these shifts, highlighting the interconnectedness of global challenges and the necessity for coordinated, multilateral responses to build a more equitable and sustainable future.

Big data is considered to be the solution to many complex problems, but its application appears to be relegated to the problems that are factorable (e.g., the tensor-like operations which reflect separable elements), not the non-factorable data from teamwork, team intelligence, and possibly not individual consciousness. In contrast, the quantum likeness of interdependence is set apart from the standard science of teams by recognizing a measurement problem between a team and its individual teammates, and between individual beliefs and actions. Teams that concern us are based on artificial intelligence (AI) and machine learning (ML) systems, which we find lacking for two reasons. First, neither AI nor ML models the human's timeless need for debate to solve a problem at the social level when facing uncertainty or complexity, where the debate of proposed actions serves to establish the boundaries of a problem in reality, no matter how complex nor uncertain. Second, at the individual level exists the illusion of a unified reality propagated by a bifurcated brain that we assume is split to determine a context with narrative and bounded spaces. We hypothesize that the quantum-likeness of interdependence applied to autonomous human-machine teams suggests that at the social level, debate models an individual's bifurcated brain, providing advantages for human-machine teams in freer systems over those oppressed by command and control systems (e.g., authoritarian regimes). Human-machine teams are coming, but they are not yet available, forcing us to rely on data from human systems. We close with plans for future research.

Renewable energy especially insights into solar energy are crucial in the energy business cycle. In this paper, an impact study of meteorological variables on solar energy production is conducted. The paper discusses the pipeline of data analysis specific to the case study and exploits open-source machine-learning algorithms to build predictive models. RandomForestRegressor and XGBoosting regressors are used to build the predictive model. The application code is integrated into an analytic software service (Power BI) and tested on Solar energy Open Data of Saudi Arabia. The solar energy production is found to be high between 800-1000 barometric pressure locations. Global Horizontal Irradiation is found to increase when the atmospheric temperature is more than 34∘ C. The impact of relative humidity is that the produced energy is high at lower humidity points. The wind speed effect is that the produced energy is significant between 2 to 4 m/s and reaches its maximum at 2.4 m/s. The predictive models produce nearly real-time predictions with Random Forest with R²: 0.909. The paper provides Global Horizontal Irradiation estimation equations using meteorological coefficients generated by the trained regressor. The paper presents implementation methodologies and records various instances of test results. It highlights the efficacy of machine learning in predictive modeling for renewable energy applications.

The unprecedented progress in Artificial Intelligence (AI), particularly in deep learning algorithms with ubiquitous internet connected smart devices, has created a high demand for AI computing on the edge devices. This review studied commercially available edge processors, and the processors that are still in industrial research stages. We categorized state-of-the-art edge processors based on the underlying architecture, such as dataflow, neuromorphic, and Processing in-Memory (PIM) architecture. The processors are analyzed based on their performance, chip area, energy efficiency, and application domains. The supported programming frameworks, model compression, data precision, and the CMOS fabrication process technology are discussed. Currently, most of the commercial edge processors utilize dataflow architectures. However, emerging non-von Neumann computing architectures have attracted the industry in recent years. Neuromorphic processors are highly efficient for performing computation with fewer synaptic operations, and several neuromorphic processors offer online training for secured and personalized AI applications. This review found that the PIM processors show significant energy efficiency and consume less power compared to dataflow and neuromorphic processors. The future direction of the industry would be to implement state-of-the-art deep learning algorithms in emerging non-Von Neumann computing paradigms for low power computing on the edge devices.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

The inherent capabilities of the K-means++ algorithm to approximate system dynamics within complex systems are subjected by constructing a network structure that captures interconnections among identified components, extending its original purpose as a data clustering method and transforming it into a tool for systems analysis. Leveraging advanced measurement technologies and sophisticated data collection systems, the K-means++ algorithm unveils hidden relationships among components and identifies critical elements. This study explored the algorithm's potential, facilitating the identification of critical components to enhance system operation, control, optimization, and decision-making and examining the practicality and resiliency of the method in real-world application with noisy and limited data. A case study conducted on power systems (IEEE 39-bus and IEEE 300-bus systems) exemplifies K-means++'s capacity to accurately identify critical components and approximate system dynamics, supported by performance metrics affirming its effectiveness and robustness in system analysis through measurements of bus similarity within clusters based on standard deviation and comparison of net tie-line flows in equivalent networks with the original network across scenarios. Performance metrics, including the Silhouette Score, Davies-Bouldin Index, and Variation of Information (VI) score, further validated K-means++'s performance, yielding reliable and consistent results.

The improvement of energy efficiency of hydraulic systems remains to be an essential challenge for the industry, and the demand for more sustainable solutions is increasing. A main focus in this endeavor is the ability to eliminate or strongly reduce the use of throttle control valves which have been the preferred control element in industrial hydraulic systems for decades. Components have been subject to continuous evolution, and current industrial grade hydraulic pumps and motors are both efficient and reliable. Even though few percentages of energy efficiency can still be achieved, the main achievements in terms of efficiency is associated with novel system designs rather than further development of components. An area subject to increasing attention is the field of variable-speed displacement control, allowing to avoid the main control valve throttle losses. Systems using this technology are, however, mainly developed as standalone drive systems, necessitating maximum force, speed and power installed in each axis, with limited hydraulic power distribution capability as compared to valve controlled systems. An emerging field addressing this challenge is so-called electro-hydraulic variable-speed drive networks which allow to completely eliminate the use of control valves and enables power sharing both electrically and hydraulically, potentially reducing the necessary installed power in many cases. The idea of such a technology was first proposed in 2022, and so far developments reported in literature have mainly been of theoretical nature. This article presents the first ever experimental results for a dual cylinder electro-hydraulic variable-speed drive network prototype. The prototype has been developed for an industrial application, but has initially been implemented in a laboratory testbench. Extensive data acquisition has been conducted while subject to the associated industrial motion cycle, under different load conditions. The data is further used in combination with models to predict the total efficiency of the drive network prototype under higher loads than what could be achieved in the laboratory, suggesting a total efficiency from the electric supply to the cylinder pistons of 68 %. Re-configuring the prototype to a known standalone drive system structure implies comparable efficiencies. Finally, the drive network is theoretically compared to a valve drive solution, generally suggesting the prototype drive network to provide efficiency improvements of at least 40 % in comparison.

The analysis of the key factors which prevent or contribute to the promotion and development of the Power Purchase Agreements (PPAs) in order to meet the sustainability goals represents an important issue which worth being investigated, especially in the situation in which entering in bilateral relations inside this contract has a powerful meaning in achieving new climate targets, developing and improving the use of green energy, and promoting a sustainable green economy. The main goal of this research is to identify and analyze the main factors which help or pre-vent the promotion and development of a PPA, in order to meet the sustainability goals by promoting a green economy. For this research survey based on comparative analysis, questionnaires and interviews with energy experts, Spearman’s correlation matrix and IBM SPSS Statistics for Window are also used. The results suggest that although there are positive interest and an open attitude towards the PPA from both sides (sellers and buyers), but there is still place for improvement, the lack of knowledge or the insufficient measures taken so far being two of the reasons way until now in Romania we do not have a developed PPA market and the level of knowledge regarding this type of mechanism is quite low.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

To address the problems of wind abandonment in the regional integrated energy system (RIES), which occurs when cogeneration unit operates in a heat-determined electricity operation mode, and the low efficiency of the energy storage system in a low-temperature environment, we propose an optimal scheduling method for RIES based on fine energy storage and wind power dissipation. First, a fine energy storage model is established on the source side and the conditional value at risk(CvaR) theory is used to quantify the uncertainty of wind power; then a combined heat and power demand response mechanism is introduced on the load side to reduce the peak-to-valley difference between heat and power loads, and to promote the consumption of wind power. Finally, with the objective of minimizing the total cost of RIES optimal dispatch, the example is solved on the MATLAB platform. The simulation results show that compared with the traditional model, the proposed model is not only more adaptable to the low-temperature environment, but also can effectively improve the system economy and wind power consumption.

Road-embedded inductive power transfer (IPT) systems have the potential to accelerate the electrification of the transportation sector. For these systems to be economically viable however, they need to have a similar durability and lifespan compared to that of asphalt roads. One area that has lacked investigation is thermally induced stresses in a primary IPT pad, which is caused by the increase in temperature of the pad when it is energized and the differing thermal expansion of the materials within. This paper presents an experimental and a finite-element based methodology for investigating the thermal-mechanical behaviour of a ¼-scale double-D pad, which was energized while suspended in air, as well as energized when embedded in pavement. A focus was placed on the measurement and prediction of strains in the magnetic ferrite cores because of their brittleness. Ferrite strains were measured using a combination of resistive strain gauges and non-metallic Fibre Bragg Grating (FBG) sensors. Coupled electromagnetic-thermal-structural simulations were conducted to predict temperature and strains in the system, with temperature-dependent properties obtained through physical testing. At an ambient temperature of 50°C, the temperature in the middle of the copper litz wire coil was predicted to be 100°C in both the suspended and embedded case. There was excellent correlation to experimental results, with a difference of less than 10% for most temperature measurements. When energized, the pad was predicted to experience an upward bow due to its temperature rise, resulting bending strains in the ferrite cores. At an ambient temperature of 50°C, maximum tensile strain in the ferrites of the embedded pad was measured to be 62 microstrain (με), with a root-mean square error that was 18 με across three sensors. The experimental and validated numerical methodology can be applied to full-scale operational IPT pads to analyse and improve their thermal-mechanical performance.

Continuous greenhouse gas emissions are causing global warming and impacting the habitats of many animals. Researchers in the field of electric power are making efforts to mitigate this situation. Operating and maintaining the power grid in an economic, low-carbon, and stable is challenging. To address the issue, we propose a grid dispatching technique that combines prediction technology, reinforcement learning, and optimization technology. Prediction technology can forecast future power demand and solar power generation, while reinforcement learning and optimization technology can make charging and discharging decisions for energy storage devices based on current and future grid conditions. In the power system, the aggregation of distributed energy resources increases uncertainty, particularly due to the fluctuating generation of renewable energy. This requires the use of advanced predictive control techniques to ensure long-term economic and decarbonization goals. In this paper, we present a real-time dispatching framework that integrates deep learning-based prediction, reinforcement learning-based decision-making, and stochastic optimization techniques. The framework can rapidly adapt to target uncertainty caused by various factors in real-time data distribution and control processes. The proposed framework achieved global Champion in the NeurIPS Challenge 2022 competition and demonstrated its effectiveness in practical scenarios of intelligent building energy management.

Besides the increase in global energy demand, access to clean energy, reduction in greenhouse gas emissions caused by conventional power generation sources, energy security, and availability of electricity in remote villages in emerging nations are some of the factors that foster the use of renewable energy sources (RESs) in generating electricity. One of the aims of initiating microgrids (MGs) is to maximize the benefits of RES and alleviate the associated grid integration issues. Microgrids are made up of RES connected to electrical loads within clearly delineated electrical limits that operate as individual controllable units on the electrical network. It can operate in-dependently as well as in connection with the grid. The paper presents an overview of microgrids and investigates the system's performance when connected to and disconnected from the grid. Furthermore, in both modes of operation, the functioning and behavior of system components such as the bidirectional DC-DC converter and energy storage system (ESS) were evaluated. The architecture of the proposed microgrid consists of a small hydropower plant, a wind farm, and a battery energy storage system (BESS). The microgrid under investigation is modeled and simu-lated using MATLAB and Simulink.

In electric circuits, energy is delivered by electromagnetic fields through the space, as suggested by Kraus and Carver. They provide insights by showing electric/magnetic fields and Poynting vector directions around a DC circuit. In this work, the energy flow mechanism by Kraus and Carver is further studied theoretically for arbitrary terminal potentials of a DC power source.

In the past few years, the possibility to transfer power wirelessly has experienced growing interest from the research community. Since the wireless channel is subject to a large number of random phenomena, a crucial aspect is the statistical characterization of the energy that can be harvested by a given device. For this characterization to be reliable, a powerful model of the propagation channel is necessary. The recently proposed Generalized-K model has proven to be very useful, as it encompasses the effects of path-loss, shadowing and fast fading for a broad set of wireless scenarios, and it is analytically tractable. Accordingly, the purpose of this paper is to characterize, from a statistical point of view, the energy harvested by a static device from an unmodulated carrier signal generated by a dedicated source, assuming that the wireless channel obeys the Generalized-K propagation model. Specifically, using simulation-validated analytical methods, this paper provides exact closed-form expressions for the average and variance of the energy harvested over an arbitrary time period. The derived formulation can be used to determine a power transfer plan that allows multiple or even massive numbers of low-power devices to operate continuously, as expected from future network scenarios such as IoT or 5G/6G.

Load variations in any power system result in losses escalation and voltage drops. With the sensible and optimal allocation of distributed generators (DGs), these problems could be considerably mitigated. It has been seen in the priorly existing methods that ideally allocation of DGs has been carried out during fixed loads and constant power requirements. However, in real scenarios the loads are always variable and allocation of DGs must be done in accordance to the variations of the connected load. Therefore, the current paper addressed the aforementioned problem by distinctive optimal allocation of DGs for each variability of 24hour load horizon. However, the single exclusive solution is considered among all allocations of 24 hours. The min-max regret concept has been utilized in order to deal with such methodology. Altogether, 24 scenarios are analyzed wherein each scenario corresponds to a specific hour of the respective day. The optimal allocation of DGs in terms of their optimal sizing and placement has been carried out by using three algorithms including battle royal optimization (BRO), accelerated particle swarm optimization (APSO) and genetic algorithm (GA). The multi-objective optimization problem is evaluated on the basis of minimum value criterion of the multi-objective index (MO). MO comprises of active and reactive power losses and voltage deviation. Hence, in order to find robustness of proposed technique, Conseil international des grands réseaux electriques (CIGRE’s) MV benchmark model incorporating 14 buses has been considerably used as a test network. In the end the results of three proposed algorithms have been compared.

With the rapid development of global offshore wind power, the demand for offshore wind power operation and maintenance is also increasing. Wisdomization of offshore wind farms is a practical need to improve the operation level and benefit of offshore wind farms. This paper first introduces the current development situation and characteristics of global offshore wind power, and expounds the current situation and main challenges of offshore wind power operation and maintenance market. Therefore, our paper discusses the innovation of offshore wind power operation and maintenance from the aspects of operation and maintenance management of offshore wind power, monitoring and analysis technology of units, far-reaching wind field monitoring and operation and maintenance risks. Then, combined with information technology and lean management concept, a smart operation and maintenance management platform for wind farms in far-reaching sea areas is built to explore centralized and intelligent operation and maintenance management mode, improve operation and maintenance efficiency of wind farms in far-reaching sea areas, and minimize operation and maintenance costs. Finally, through the research on the characteristics of 5G technology, combined with the practical experience of operation and maintenance, and in view of the characteristics of offshore wind farms, we analyze and propose several typical application scenarios of 5G technology in the intelligent operation and maintenance of offshore wind farms, which provides a new solution for the efficient operation and maintenance of offshore wind farms.

Integrated photovoltaic-fuel cell (IPVFC) systems, amongst other integrated energy generation methodologies are renewable and clean energy technologies that have received diverse research and development attentions over the last few decades due to their potential applications in a hydrogen economy. This article systematically updates the state-of-the-art of IPVFC systems and provides critical insights into the research and development gaps needed to be filled/addressed to advance these systems towards full commercialisation. The design methodologies, renewable energy-based microgrid and off-grid applications, energy management strategies, optimisations and the prospects as self-sustaining power source were covered. IPVFC systems could play an important role in the upcoming hydrogen economy since they depend on solar hydrogen which has almost zero emissions during operation. Highlighted herein are the progresses as well as the technical challenges requiring research efforts to solve to realise numerous potential applications of IPVFC systems such as in unmanned aerial vehicles, hybrid electric vehicles, agricultural applications, telecommunications, desalination, synthesis of ammonia, boats, buildings, and distributed microgrid applications.

A family of linear singularly perturbed Cauchy problems is studied. The equations defining the problem combine both partial differential operators together with the action of linear fractional transforms. The exotic geometry of the problem in the Borel plane, involving both sectorial regions and strip-like sets, gives rise to asymptotic results relating the analytic solution and the formal one through Gevrey asymptotic expansions. The main results lean on the appearance of domains in the complex plane which remain intimately related to Lambert W function, which turns out to be crucial in the construction of the analytic solutions. On the way, an accurate description of the deformation of the integration paths defining the analytic solutions and the knowledge of Lambert W function are needed in order to provide the asymptotic behavior of the solution near the origin, regarding the perturbation parameter. Such deformation varies depending on the analytic solution considered, which lies in two families with different geometric features.

The work is devoted to the study of a family of linear initial value problems of partial differential equations in the complex domain, dealing with two complex time variables. The use of a truncated Laplace-like transformation in the construction of the analytic solution allows to overcome a small divisor phenomenon arising from the geometry of the problem and represents an alternative approach to the one proposed in a recent work by the first two authors. The result leans on the application of a fixed point argument and the classical Ramis-Sibuya theorem.

A nonlinear singularly perturbed Cauchy problem with confluent fuchsian singularities is examined. This problem involves coefficients with polynomial dependence in time. A similar initial value problem with logarithmic reliance in time has been investigated by the author in a recent work, for which sets of holomorphic inner and outer solutions were built up and expressed as a Laplace transform with logarithmic kernel. Here, a family of holomorphic inner solutions are constructed by means of exponential transseries expansions containing infinitely many Laplace transforms with special kernel. Furthermore, asymptotic expansions of Gevrey type for these solutions relatively to the perturbation parameter are established.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

This paper presents a novel adaptive fault-tolerant neural-based control design for wind turbines with unknown dynamic and unknown wind speed. By utilizing the barrier Lyapunov function in the analysis of the Lyapunov direct method, the constrained behavior of the system is provided in which the rotor speed, its variation and generated power remain in the desired bounds. In addition, input saturation is also considered in terms of smooth pitch actuator bounding. Furthermore, by utilizing a Nussbaum-type function in designing the control algorithm, the unpredictable wind speed variation is captured without requiring accurate wind speed measurement, observation or estimation. Moreover, with the proposed adaptive analytic algorithms, together with the use of radial basis function neural networks, a robust adaptive and fault-tolerant control scheme is developed without the need for precise information about the wind turbine model nor the pitch actuator faults. Additionally, the computational cost of the resultant control law is reduced by utilizing a dynamic surface control technique. The effectiveness of the developed design is verified using theoretical analysis tools and illustrated by numerical simulations on a high-fidelity wind turbine benchmark model with different fault scenarios. Comparison of the achieved results to the ones that can be obtained via an available industrial controller shows the advantages of the proposed scheme.

Sediment transport is highly sensitive to flow conditions, showing significant increase during flood events. Based on this principle, this study set out to rank flood events occurring along river Trotuș (Romania) based on the amount of transported sediment and event duration. The 77 flood events recorded from 2000 to 2017 were ranked into 4 classes: type A (4%); type B (16%), type C (14%) and type D (66%). The sediment transport specific for the 4 types of flood events was related to the flow discharge (sediment rating curve and hysteresis effect), the specific stream power and the energy expenditure of these events. More than 60% of the hysteresis loops typical for flood events were clockwise, thus singling out the channel as the main sediment source. Ca. 74% of the total sediment yield was transported at stream power values higher than the 300 Wm-2 threshold, which was exceeded in less than 1% of the investigated timeframe. The changes occurring in the sediment transport rates after major floods show that these events are significant thresholds in the hydrogeomorphic evolution of river channels.

This paper aims to present a smart high speed battery charger, powered by a photovoltaic module array, for a LiFePO4 battery as a solar energy storage device. With a battery charging strategy, the presented battery charger involves a Buck converter as the core equipped with a simple maximum power point (MPP) tracker. Considering complexity reduction and easy hardware implementation, a constant voltage MPP tracking approach is adopted such that the maximum amount of output power can be delivered to the load in response to an arbitrary change in the solar radiation. A smart two-stage charging strategy, with a constant current mode followed by a constant voltage mode, is employed in such a way that the battery charge process can be accelerated largely, while the damage caused by overcharging can be prevented. In the end, the performance of this proposal is validated experimentally.

Oil immersed paper insulation condition is a crucial aspect of power transformer’s life condition diagnostic. The measurement testing database collected over the years made it possible for researchers to implement classification analysis to in-service power transformer. This article presents classification analysis of transformer oil-immersed paper insulation condition. The measurements data (dielectric characteristics, dissolved gas analysis, and furanic compounds) of 149 transformers with primary voltage of 150 kV had been gathered and analyzed. The algorithm used for developing classification model is Support Vector Machine (SVM). The model has been trained and tested using different datasets. Different models have been created and the best chosen, resulting in 90.63% accuracy in predicting the oil-immersed paper insulation condition. Further implementation was executed to classify oil-paper condition of 19 Transformers which Furan data is not available. The classification results combined, reviewed, and compared to conventional assessment methods and standards, confirming that the model developed has the ability to do classification of current oil-paper condition based on Dissolved Gasses and Dielectric Characteristics.

Compared with conventional methods of fault diagnosis for power transformers, which have defects such as imperfect encoding and too absolute encoding boundaries, this paper systematically discusses various intelligent approaches applied in fault diagnosis and decision making for large oil-immersed power transformers based on dissolved gas analysis (DGA), including expert system (EPS), artificial neural network (ANN), fuzzy theory, rough sets theory (RST), grey system theory (GST), swarm intelligence (SI) algorithms, data mining technology, machine learning (ML), and other intelligent diagnosis tools, and summarizes existing problems and solutions. From this survey, it is found that a single intelligent approach for fault diagnosis can only reflect operation status of the transformer in one particular aspect, causing various degrees of shortcomings that cannot be resolved effectively. Combined with the current research status in this field, the problems that must be addressed in DGA-based transformer fault diagnosis are identified, and the prospects for future development trends and research directions are outlined. This contribution presents a detailed and systematic survey on various intelligent approaches to faults diagnosing and decisions making of the power transformer, in which their merits and demerits are thoroughly investigated, as well as their improvement schemes and future development trends are proposed. Moreover, this paper concludes that a variety of intelligent algorithms should be combined for mutual complementation to form a hybrid fault diagnosis network, such that avoiding these algorithms falling into a local optimum. Moreover, it is necessary to improve the detection instruments so as to acquire reasonable characteristic gas data samples. The research summary, empirical generalization and analysis of predicament in this paper provide some thoughts and suggestions for the research of complex power grid in the new environment, as well as references and guidance for researchers to choose optimal approach to achieve DGA-based fault diagnosis and decision of the large oil-immersed power transformers in preventive electrical tests.

In this research paper, a hybrid Artificial Neural Network (ANN)-Fuzzy Logic Control (FLC) tuned Flower Pollination Algorithm (FPA) as a Maximum Power Point Tracker (MPPT) is employed to emend root mean square error (RMSE) of photovoltaic (PV) modeling. Moreover, Gaussian membership functions have been considered for fuzzy controller design. This paper interprets Luo converter occupied brushless DC motor (BLDC) directed PV water pump application. Experimental responses certify the effectiveness of the suggested motor-pump system supporting diverse operating states. Luo converter is newly developed dc-dc converter has high power density, better voltage gain transfer and superior output waveform and able to track optimal power from PV modules. For BLDC speed controlling there is no extra circuitry and phase current sensors are enforced for this scheme. The recentness of this attempt is adaptive neuro-fuzzy inference system (ANFIS)-FPA operated BLDC directed PV pump with advanced Luo converter has not been formerly conferred.

This study investigates the properties of solution processed hybrid pol-yimide, PI nanocomposites containing a variety of nanofillers, including polyaniline copolymer modified clay, PNEA, nanographene sheets, NGS, and carbon nanotube sheet, CNT-PVDF, respectively. Through a series of experiments, the flow behavior of poly(amic acid), PAA solution and PAA suspension containing polyaniline copolymer modified clay, PNEA was determined as a function of the shear rate, processing temperature and polymerization time. It is shown that the neat PAA solution exhibited a complex rheological behavior ranging from shear thickening to New-tonian behavior with increasing shear rate and testing temperature. The presence of modified clay in PAA solution significantly reduced the viscosity of PAA. Differential Scanning Calorimetry (DSC) analysis show that polyimide-nanographene sheets, PI NGS nanocomposites processed at high spindle speed (100 rpm) had lower total heat of decomposition which is indicative of improved fire retardancy. The effect of processing temperature on the specific capacitance of polyimide-CNT-PVDF composites containing electrodeposited polypyrrole fillers was determined by using cyclic voltammetry, CV. It was shown that the hybrid composite working electrode material processed at 90˚C produced a remarkably higher overall stored charge when compared to the composite electrode material processed at 250˚C. Consequently, the specific capacitance ob-tained at a scan rate of 5 mV/s for the hybrid nanocomposite processed at 90°C was about 858 F/g after 1 cycle, which is about 6.3 times higher than the specific capacitance of 136 F/g produced by the hybrid nanocomposite processed at 250°C. These findings show that the properties of the hybrid nanocomposites are remarkably influenced by the processing conditions and highlights the need for process optimization.

This study introduces a robust methodology utilizing Multi-Criteria Decision Analysis (MCDA) combined with the Analytic Hierarchy Process (AHP) to repurpose abandoned hydrocarbon fields for energy storage, supporting the transition to renewable energy sources. We use a geostatistical approach integrated with Python scripting to analyze reservoir parameters—including porosity, permeability, thickness, lithology, temperature, heat capacity, and thermal conductivity—from a decommissioned hydrocarbon field in Southeast Hungary. Our workflow leverages stochastic simulation data to identify potential zones for energy storage, categorizing them into high, moderate, and low suitability scenarios. This innovative approach provides rapid and precise analysis, enabling effective decision-making for energy storage implementation in depleted fields.

Combustion parameters are the important aspects in the development and research of an internal combustion engines. Hence present work is an attempt to develop an artificial neural network (ANN) model for anticipating the combustion characteristics of computerized CI DI VCR, four strokes, single cylinder, and water cooled engine using mixture of two biodiesel and diesel blends as a fuel. The two biodiesel selected are Jatropha and Simarouba and mixed in the ratio of 75:25. Two biodiesel mixtures is used for the preparation of various blends with diesel. Experiments are carried out at different compression ratio, at different % load and blends B20, B40, B60and neat diesel (B00) fuel to accumulate the assorted combustion data. The input variables are % load, compression ratio, blends and crank angle. The outputs well thought-out are cylinder pressure (CP), net heat release rate (NHRR), cumulative heat release (CHR), rate of pressure rise (RPR), mass fraction burned (MFB) and maximum cylinder pressure. The assessment is focused on developing artificial neural network for the prediction and verifying the combustion characteristics of engine. MATLAB software is used for analysis of different combustion aspects of the engine. Multilayer neural network perceptions are used with Feed-Forward Back Propagation algorithm with performance function for mapping the input and output parameters. The experimental outcomes are compared with ANN estimated results for the analysis. The outcome from the study authenticate that experimental results are in match with ANN results. The accuracy of the ANN model shows the developed model can effectively predict the engine combustion characteristics with excellent regression coefficients ‘R’ and its values are close to unity and the mean square errors are extremely less. ANN model approach is competent towards predicting the combustion aspect of diesel engine with good accuracy

The relocation of the Indonesian capital from Jakarta to Ibu Kota Nusantara (IKN) East Kalimantan IKN will affect several sectors. The change in land use from vegetated to developed land will lead to local climate changes, including the emergence of the urban heat island (UHI) phenomenon, which is reflected in a higher land surface temperature (LST) than the surrounding area. In this study, an analysis of UHI propagation was conducted on a seasonal (DJF, MAM, JJA, and SON), with 5 yearly periods from 2001 to 2020, study area in IKN and its buffer cities (Balikpapan, Samarinda, and Bontang). Terra-MODIS satellite data are processed using Google Earth Engine (GEE) platform and output is done using GrADS. UHI (high LST) is found in urban areas/buffer cities both spatially and temporally in every season, while UHI has not yet occurred in IKN (low LST) and suburban, rural, hilly areas, vegetated areas, and water bodies (lakes, rivers). The cross-sectional latitudinal and longitudinal analysis showed that the LST DJF2015-2020 from highest to lowest temperature are in Balikpapan City (36.84 OC), Samarinda City (36.13 OC), Bontang City (32.3 OC); and IKN zero point (28.82 OC). The UHI propagation was observed in 2001-2005, 2006-2010, 2011-2015, and most during 2016-2020. Seasonally, the UHI was most pronounced in the SON season, while on lowest UHI was observed in the MAM season.

A major advance of drug discovery and targeted therapy directed to cancer cells may be achieved by exploitation and immunomodulation of their unique biological property. This re-view summarizes our efforts to develop novel chemo-thermo-immuno-therapy (CTI therapy) by conjugating a melanogenesis substrate, N-propionyl cysteaminylphenol (NPrCAP: amine analog of tyrosine), with magnetite nanoparticles (MNP). In our approach, NPrCAP provides a unique drug delivery system (DDS) because of its selective incorporation into melanoma cells. It also functions as a melanoma-targeted therapeutic drug because of its production of highly reactive free radicals (melanoma-targeted chemotherapy). Moreover, utilization of MNP is a platform to develop thermo-immunotherapy because of heat shock protein (HSP) generation upon exposure to an alternating magnetic field (AMF). The feasibility of our approach was successfully shown in experimental in vivo and in vitro mouse melanoma models and in preliminary clinical trials to a limited number of advanced melanoma patients.

The aim of this work is to introduce a mathematical model representing the evolution of the temperature in a vegetation cover and the ground underneath it. Vegetation, and its interaction with soil, plays a very important role in the protection of soil surface from the action of sun and precipitations. A reduction in the vegetated mass increase the risk of desertification, soil erosion or surface runoffs which which can give rise to soil loss and sediment retention. These processes can favour climate change and global warming, which are major concerns nowadays. The mathematical model presented takes into account the main processes involved in vegetation cover and the interaction with the soil, among which, we can mention the Leaf Area Index, which is a dimensionless quantity defined as the one-sided green leaf area per unit ground surface area, or albedo and co-albedo which are clearly influenced by the vegetation. It is also considered a nonlinear heat capacity in the soil which incorporates the latent heat of fusion, when the phase change takes place. The numerical technique used to solve the mathematical model is based on a finite volume scheme with Weighted Essentially Non Oscillatory technique for spatial reconstruction and the third order Runge-Kutta Total Variation Diminishing numerical scheme is used for time integration. Some numerical examples are solved to obtain the distribution of temperature both in the vegetation cover and the soil.

We present the results on photothermal (PT) and heat conductive properties of nanogranular silicon (Si) films synthesized by evaporation of colloidal droplets (drop-casting) of 100 ± 50 nm sized crystalline Si nanoparticles (NP) deposited on glass substrates. Finite difference time domain (FDTD) and finite element mesh (FEM) modeling of absorbed light intensity and photo-induced spatial temperature distribution across the Si NP films were well correlated with the local temperatures measured by micro-Raman spectroscopy and used for determination of heat conductivities in the films of various thicknesses. Cubic-to-hexagonal phase transition in these films caused by laser heating was found to be heavily influenced by the film thickness and heat conductive properties of glass substrate, on which the films were deposited. Heat conductivities across the drop-casted Si nanogranular films were found to be in the range of lowest heat conductivities of other types of nanostructurely voided Si films due to enhanced phonon scattering across inherently voided topology, weak NP-NP and NP-substrate interface bonding within nanogranular Si films.

As the first time, 0D-1D-3D and fully 3D steady-state aero-thermo-fluid simulations of a structural oil-to-air Fan Outlet Guide Vane Cooler (FOGVC) in a jet engine are presented. Using the commercial softwares Ansys Fluent, the thermo-mechanical module of Ansys and the 1D fluid solver Flownex, 5 simulation types (3D fully conjugate heat transfer with and without a thin wall model, 3D with a thin wall model, 1D-3D coupled, 1D and 0D) corresponding to 4 levels of simplification in 3 possible domains (oil, oil-metal and oil-metal-air) have been compared to provide selection criteria when a determined level of accuracy in the simulations without prohibited computational times is desired. The methodologies are applied to two different oil internal cavities: an inverted U with rectangular cross section and a coil internal cavity with a circular cross section. The obtained results show that depending on the scope of the research (outlet oil temperature, dissipated heat rate or oil pressure drop) and the accuracy of the results, one method or the other may be used. Experimental data would be needed to validate the numerical results by all employed methodologies and geometries.

Specific climate adaptation and resilience measures can be efficiently designed and implemented at the regional and local level. Climate and environmental databases are of critical importance to achieving sustainability goals (SDGs) and for the efficient planning and implementation of suitable mitigation measures: Available databases can serve municipalities as a vital starting points to determine requirements, prioritize resources and allocate investments under consideration of commonly tight budget restrictions. High-quality geo, climate and environmental data are now available – data from remote sensing, i.e. Copernicus services will be of crucial importance. Forward-looking approaches exist to using such data to derive forecasts for urban planning process optimization for municipal administrations. On municipal level, however, the existing data have so far only been used to a limited extent, since there are no practical tools for urban planning that can be used to merge and meaningfully combine remote sensing data with local data and to further process and apply in municipal planning processes. Therefore, our project CoKLIMAx aims at the development of new digital products, advanced urban services and procedures, such as the development of practice-oriented technical tools that acquire various remote sensing and in-situ data sets for validation and further processing.

Extracellular vesicles (EV) released by tumor cells are a major aspect of the resistance-associated secretory phenotype (RASP), by which immune evasion can be established. Heat shock proteins (HSPs) are an evolutionarily conserved family of molecular chaperones, which stabilize proteins, minimize protein misfolding and aggregation within the cell, besides facilitating protein translocation, refolding and degradation. (i) Releases of extracellular HSPs (ex-HSP) and EV-associated HSPs (EV-HSP) are essential in RASP, by which molecular cotransfer of HSPs with oncogenic factors into recipient cells can promote cancer progression and resistance against stress such as hypoxia, radiation, chemicals, and immune system. (ii) RASP of tumor cells can eject anticancer drugs, molecularly targeted therapeutics, and immune checkpoint inhibitors with EVs. (iii) Cytotoxic lipids can be also released from tumor cells as RASP. Nevertheless, ex-HSP and EV-HSP can play immunostimulatory and immunosuppressive roles by binding to receptors such as LRP1/CD91/A2MR, scavenger receptors, and toll-like receptors expressed on recipient cells. Liquid biopsy of HSPs in body fluids may be useful in diagnosis, prognosis, and treatment in cancer. Regarding HSP90-targeted therapeutics, we summarize the pros, cons, and problem solutions in this review. Although production of HSPs are canonically induced by heat shock factor 1 (HSF1) and hypoxia-inducible factor 1 (HIF-1), recent studies discovered that production of HSPs is also regulated by matrix metalloproteinase 3 (MMP3) and heterochromatin protein 1 (HP1) and production of cochaperone CDC37 is reciprocally regulated by myeloid zinc finger 1 (MZF1) and SCAN-D1.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.

Background: Gestational trophoblastic neoplasia (GTN) is a rare tumor with an excellent prognosis. This study aimed to refine the FIGO risk score by incorporating immune nutritional factors. Methods: A retrospective analysis was conducted on women diagnosed with GTN between 2005 and 2019 who received chemotherapy (CT). Statistical tests (Wilcoxon, univariate, multivariate analyses) were used to assess associations with response to CT, and Cox regression models were applied to identify factors influencing overall survival (OS). immune nutritional FIGO (in-FIGO) risk score was calculated using significant variables and compared to the original FIGO score using ROC curves. Results: A total of 160 GTN patients were included. There was a positive association between CR and prognostic nutritional index (PNI) (p <0.0001) and neutrophils lymphocyte ratio (NLR) (p <0.001). In multivariate analysis, only PNI had a significant association (p= 0.001). A significant association was found between higher PNI (HR 0.95-IC 0.91-0.99, p= 0.019) and OS. ROC curves of the in-FIGO risk and FIGO risk scores were compared. For CR to chemotherapy, the in-FIGO score had higher sensitivity (71.6 vs. 61.5%), specificity (74.3 vs. 62.9%), and AUC (0.719 vs. 0.633) than the original FIGO score. For OS, the in-FIGO score demonstrated higher sensitivity (92% vs. 72.4%) but lower specificity (45.0% vs. 61.8%) and AUC (0.691 vs. 0.710) compared to the original FIGO score. Conclusions: PNI is a significant predictor of both CR and OS in women with GTN receiving CT. The in-FIGO score demonstrated improved sensitivity and specificity in predicting complete response to CT compared to the original FIGO score.

Esophageal cancer is an extremely deadly tumor that accounts for 5% of all cancer deaths. The two main subtypes of the disease are esophageal squamous cell carcinoma (ESCC) and esophageal adenocarcinoma (EAC). To date, few studies analyse EAC for transcriptional signatures associated with diagnosis and/or prognosis, while most focus on the analysis of transcriptional profiles of ESCC. In this study, we used single-cell RNA sequencing (scRNA-seq) analysis of CD45+ cells enriched from Tumors and matched Non Tumor tissues from therapy naїve patients to identify all types of immune cells present in tumor immune infiltrate and its transcriptional profile. In addi-tion, we analysed the entire transcriptome in a cohort of 23 patients whose tissue biopsies were taken from Tumors and matched with Non Tumor tissue. The transcriptional signatures we obtained were then used to stratify a large cohort of TCGA EAC patients, demonstrating a strong association with their prognosis, as well as the ability to predict a patient's clinical outcome and better define the prognosis of EAC after surgery. In addition, these features may lead patients to effective therapies including immunotherapy approaches.

This work presents a historical-epistemological analysis of the foundations of quantum mechanics. From a philosophical point of view, the relationships between quantum mechanics and scientific realism are highlighted, as well as the influence of the neo-positivist philosophy of the first decades of the 20th century. The great significance of measurement in the context of quantum mechanics is underlined, as an essential element in providing a coherent description of reality moving from the microcosm to the macrocosm, as well as the role that the measurement apparatus and the consciousness of the observer assume during the act of measurement, the ontological problem, the problem of the objectification of the wave function and the problem of the definition of discernibility. This is followed by an overview of the most important alternative proposals to the standard interpretation (Copenhagen interpretation), with particular reference to hidden variable theories, and other alternatives to standard quantum mechanics that profoundly modify the vision of reality, such as the Everett’s many-worlds theory, the QBism, the unified holistic approach.

When separation to the parameters of interest appears below resolution limit of the estimator, the ambiguity arises whether two parameter estimates relate to one source emitted twice or two close sources emitted once. In the paper, novel Bayes technique aimed to identify one/two sources below resolution limit by the pair of Gaussian estimates of a source(s) planar location as parameter is developed. Prior probabilities of the hypotheses on one/two sources are available from the analysis of physical characteristics of the emissions, assuming that they can be equally probable. The identifier recalculates a posteriori these probabilities subject to a distance between sources. It is applied to distinguish two location estimates obtained in the planar time difference of arrival mobile communication network. The work of the identifier is studied in the domain of closely spaced network users where covariance matrices of estimates are sufficiently approximated by the constant. The application gives an example of how the identifier revises the prior probabilities and can change thereby the initial preference of a hypothesis with a distance between users in some cases.