This paper presents the results of the investigation of composite sinters W-TiB2 which were used as an electrode in the process of electro-spark deposition (ESD) and the examination of the deposited layers. The scope of the study includes detailed characteristics of powder mixtures, composite sinters made using the spark plasma sintering method (SPS) and layers deposited in the electro-spark process. The ESD process, using the W+30 vol.% TiB2 electrode, was carried out using an automated device. The substrates were made of copper and aluminium. The topography analysis of the surfaces of the composite layer and the evaluation of their wear resistance properties are also presented. The analysis of the results of research showed the possibility to obtain, using the SPS method, composite materials of good quality, which can be used as electrodes in the ESD process. The obtained layers had increased wear resistance in relation to the substrate material.

We present progress in fast, high-resolution imaging, material classification, and fault detection using hyperspectral X-ray measurements. Classical X-ray CT approaches rely on data from many projection angles, resulting in long acquisition and reconstruction times. Additionally, conventional CT cannot distinguish between materials with similar densities. However, in additive manufacturing, the majority of materials used are known a priori. This knowledge allows to vastly reduce the data collected and increase the accuracy of fault detection. In this context, we propose an imaging method for non-destructive testing of materials based on the combination of spectral X-ray CT and discrete tomography. We explore the use of spectral X-ray attenuation models and measurements to recover the characteristic functions of materials in heterogeneous media with piece-wise uniform composition. We show by means of numerical simulation that using spectral measurements from a small number of angles, our approach can alleviate the typical deterioration of spatial resolution and the appearance of streaking artifacts.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

Quality assurance has been one of the major challenges in laser-based additive manufacturing (AM) processes. This study proposes a novel process modeling methodology for layer-wise in-situ quality monitoring based on image series analysis. An image-based autoregressive (AR) model has been proposed based on the image registration function between consecutively observed thermal images. Image registration is used to extract melt pool location and orientation change between consecutive images, which contains sensing stability information. Subsequently, a Gaussian process model is used to characterize the spatial correlation within the error matrix. Finally, the extracted features from the aforementioned processes are jointly used for layer-wise quality monitoring. A case study of a thin wall fabrication by a Directed Laser Deposition (DLD) process is used to demonstrate the effectiveness of the proposed methodology.

Additive Manufacturing (AM) simplifies the fabrication of complex geometries. Its scope has rapidly expanded from the fabrication of pre-production visualization models to the manufacturing of end use parts driving the need for better part quality assurance in the additively manufactured parts. Machine learning (ML) is one of the promising techniques that can be used to achieve this goal. Current research in this field includes the use of supervised and unsupervised ML algorithms for quality control and prediction of mechanical properties of AM parts. This paper explores the applications of supervised learning algorithms - Support Vector Machines and Random Forests. Support vector machines provide high accuracy in classifying the data and is used to decide whether the final parts have the desired properties. Random Forests consist of an ensemble of decision trees capable of both classification and regression. This paper reviews the implementation of both algorithms and analyzes the research carried out on their applications in AM.

It is time-consuming for acquiring complete data by fully phase encoding in two orthogonal directions along with one frequency encoding direction. Undersampling in the 3D k-space is promising in accelerating such 3D MRI process. Though 3D undersampling can be conducted according to predefined probability density, the density based method is not optimal. Because of the large amount of 3D data and computational cost, it is challenging to perform data-driven and learning-based 3D undersampling and subsequent 3D reconstruction. To tackle this challenge, this paper proposes a deep neural network called EEUR-Net, realized by optimizing specific undersampling patterns for the fully-sampled 3D k-space data. Innovatively, our undersampling algorithm employs an end-to-end deep learning approach to optimize phase encoding patterns and uses a 3D U-Net for image reconstruction of undersampled data. Through end-to-end training, we obtain an optimized 3D undersampling pattern, which significantly enhances the quality of the reconstructed image under the same acceleration factor. A series of experiments on a knee MRI dataset demonstrated that, in comparison to standard random uniform, radial, Poisson and equispaced Cartesian undersampling schemes, our end-to-end learned undersampling pattern considerably improves the reconstruction quality of undersampled MRI images.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

Solar3D is an open-source software application designed to interactively calculate solar irradiation at three-dimensional (3D) surfaces in a virtual environment constructed with combinations of 3D city models, digital elevation models (DEMs), digital surface models (DSMs) and feature layers. The GRASS GIS r.sun solar radiation model computes solar irradiation based on two-dimensional (2D) raster maps for given day, latitude, surface and atmospheric conditions. With the increasing availability of 3D city models and demand for solar energy, there is an urgent need for better tools to computes solar radiation directly with 3D city models. Solar3D extends GRASS GIS r.sun from 2D to 3D by feeding the model with input, including surface slope, aspect and time-resolved shading, that is derived directly from the 3D scene using computer graphics techniques. To summarize, Solar3D offers several new features which, as a whole, distinguish itself from existing 3D solar irradiation tools: (1) the ability to consume massive heterogeneous 3D city models, including massive 3D city models such as oblique airborne photogrammetry-based 3D city models (OAP3Ds or integrated meshes); (2) the ability to perform near real-time pointwise calculation for duration from daily to annual; (3) the ability to integrate and interactively explore large-scale heterogeneous geospatial data. (4) the ability to calculate solar irradiation at arbitrary surface positions including at rooftops, facades and the ground. Solar3D is publicly available at https://github.com/jian9695/Solar3D.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

The evaluation of landslide hazard in seismic areas is based on a deterministic analysis to define the stability of the sites. However, deterministic analysis is not able to consider various uncertainties in the analysis process. This paper focuses on the results established by the probabilistic seismic hazard analysis and extends the probabilistic landslide hazard analysis to consider the uncertainties of opposing ground deformations and strength. The work studies the areas between Nibbiano and Sant'Erasmo inhabited centres in the Camerino municipality located in central Italy. The current state of the areas shows dangerous conditions for the building structures. In fact, all constructions present evidence of damage caused by both the 2016 earthquake and slope instability. The studies, carried out through careful geological survey and detailed geophysical investigations, are performed to define the geological, geomorphological and hydrogeological characteristics of the areas and also to run a new analysis aimed to define the material stress-strain behavior. Both inhabited Centers are located on debris deposits with highly variable thicknesses. The key point regards the definition of the depth of unstable mass, its position and its extension. Therefore, this contribution aims to summarize the knowledge of the landslide phenomenon that affected the area, trying to interpret its evolution with new field investigations. Indeed, during the first step, related to the geological and geomorphological detailed surveys, a remarkable geological model was obtained to better interpret the slope dynamics in relation to the structures of this section of the ridge. This model was also confirmed by the geophysical investigations. The study involves a more detailed definition of the landslide perimeter. Indeed, to analyze the phenomenon, it was necessary to study both the local seismic amplification with finite element 2D simulations and the slope stability conditions with finite 3D difference simulation.

Background. Currently, most of the research in breast cancer has been carried out in conventional two-dimensional (2D) cell culture due to its practical benefits, however, the three-dimensional (3D) cell culture is becoming the model of choice in cancer research because it allows cell-cell and cell-extracellular matrix (ECM) interactions, mimicking the native microenvironment of tumors in vivo. Methods. in this work, we evaluated the effect of 3D cell organization on the expression pattern of miRNAs (by Small-RNAseq) and mRNAs (by microarrays) in the breast cancer SKBR3 cell line and analyzed the biological processes and signaling pathways regulated by the differ-entially expressed protein-coding genes (DE-mRNAs) and miRNAs (DE-microRNAs) found in the organoids. Results. We obtained well-defined cell-aggregated organoids with a grape cluster-like morphology with a size up to 9.2×105 μm3. The transcriptomic assays showed that cell growth in organoids significantly affected (all p < 0.01) the gene expression patterns of both, miRNAs and mRNAs, finding 20 upregulated and 19 downregulated DE-microRNAs, as well as 49 upregulated and 123 downregulated DE-mRNAs. In silico analysis showed that a subset of 11 upregulated DE-microRNAs target 70 downregulated DE-mRNAs. These genes are involved in 150 gene on-tology (GO) biological processes such as regulation of cell morphogenesis, regulation of cell shape, regulation of canonical Wnt signaling pathway, morphogenesis of epithelium, regulation of cy-toskeleton organization, as well as in the MAPK and AGE-RAGE signaling KEGG-pathways. In-terestingly, hsa-mir-122-5p (Fold Change (FC)=15.4), hsa-mir-369-3p (FC=11.4), and hsa-mir-10b-5p (FC=20.1) regulated up to the 81 % of the 70 downregulated DE-mRNAs. Conclu-sion, the organotypic 3D cell-organization architecture of breast cancer SKBR3 cells impacts the expression pattern of miRNAs-mRNAs network mainly through overexpression of hsa-mir-122-5p, hsa-mir-369-3p, and hsa-mir-10b-5p. All these findings suggest that the interaction between cell-cell and cell-ECM as well as the change in the culture architecture impacts gene ex-pression, and therefore, support the pertinence of migrating breast cancer research from conven-tional cultures to 3D models.

Path planning in 3D environment is a fundamental research area for robots and autonomous vehicles. Based on the principle ``the shortest path consists of tangents'', RimJump* is proposed as a tangent-based path planning method suitable for finding the shortest path (both off-ground and on-ground) in 3D space (e.g., octomap and point cloud) for mobile platform to follow. RimJump* searches the tangent graph in the form of a path tree and considers the geometrical properties of the locally shortest path. Therefore, the method can provide all of the locally shortest paths that connect the starting point and the target, including the globally shortest path. And the time cost of RimJump* is insensitive to map scale increases in comparison to methods that search the whole passable space rather than the surface of the obstacle, e.g., Dijkstra and A*. In the Results, RimJump* is compared with other methods in terms of path length and time cost.

Background: Melatonin is a potent mitochondrial, cytoprotective and antioxidant molecule with potentially strong anti-aging properties. Topical melatonin has shown to improve the clinical signs of skin aging. Melatosphere™ is a new lipid-based delivery system able to improve stability and skin penetration of melatonin when used in topical formulations. No clinical studies, using objective instrumental data, are available so far regarding the positive effect of Melatosphere™ in improving wrinkles in women with mild-to-moderate skin aging. Study Aim: We evaluate, in an open prospective, evaluator-blinded trial, the effects on skin texture of 2 months treatment with a Melatosphere™ based cream. Subjects and Methods: 15 women aged >45 years with mild to moderate facial skin aging (Glogau score ≥2) participated in the trial, after their informed consent. An ANTERA 3D computer-assisted skin analysis evaluation for the assessment of coarse and fine wrinkles of the periorbital area and melanin content was performed at baseline and after two months of treatment. An evaluator-blinded Investigator Global assessment of skin elastosis, roughness, level of dyscromia, skin dryness and presence of actinic damage was also performed at the same time points using a 4-grade score from 0 (no sign) to 3 (severe sign). Results: At baseline the mean (SD) IGA score was 8.2(1.0). After 2 months the IGA score significantly decrease to 4.2(1.4) (49% reduction) (P=0.0007). ANTERA 3D evaluations showed a significant reduction in skin coarse and fine wrinkles volume in the target area of -31% and -18%, respectively. Melanin content was reduced significantly by -17%. Conclusion: Topical melatonin carried in Melatosphere improves in the short-term signs of skin aging evaluated clinically and by ANTERA 3D device in women with mild to moderate skin aging.

We demonstrated a new approach to the production of three-dimensional-coated patterns using liquid route. Metallic perovskite oxides were coated onto three-dimensional (3D) microstructured substrates with different aspect ratios. The success of the method relies on the solution viscosity monitored by adding viscous liquid. The process of oxide thin films consists in three steps: preparing the precursor solution, coating the solution by spin-coating process onto three-dimensional-Si substrates and post-annealing. The chemical solution 3D-coating is conformal.

Prior to clinical trials, preclinical testing of oncology drug candidates is performed by evaluating drug candidates with in vitro and in vivo platforms. For in vivo testing, animal models are used to evaluate the toxicity and efficacy of drug candidates. However, animal models often display poor translational results as many drugs that pass preclinical testing fail when tested in humans, with oncology drugs exhibiting especially poor acceptance rates. The FDA Modernization Act 2.0 promotes alternative preclinical testing techniques, presenting the opportunity to use higher complexity in vitro models as an alternative to in vivo testing, including 3D cell culture models. 3D tissue cultures address many of the shortcomings of 2D cultures by more closely replicating the tumour microenvironment through a combination of realistic drug diffusion, paracrine signaling, cellular phenotype, and vascularization that can better mimic native human tissue. This review will discuss the common forms of 3D cell culture, including cell spheroids, organoids, organs-on-a-chip, and 3D bioprinted tissues. Their advantages and limitations will be presented, aiming to discuss the use of these 3D models to accurately represent human tissue and as an alternative to animal testing. The use of 3D culture platforms for preclinical drug development is expected to accelerate as these platforms continue to improve in complexity, reliability, and translational predictivity.

Transparent and high-hardness materials have become the object of wide interest. Most notably, it concerns technical glasses and crystals. A notable example is a sapphire – one of the most rigid materials having impressive mechanical stability and good optical properties. Nonetheless, using this material for 3D micro-fabrication is not straightforward due to its brittle nature. On the microscale, selective laser etching (SLE) technology is an appropriate approach for such media. Therefore, we present our research on c-cut crystalline sapphire microprocessing by using femtosecond radiation-induced SLE. Here we demonstrate a comparison between different wavelength radiation (1030 nm, 515 nm, 343 nm) usage for modification inscription and various etchants (Hydrofloridic acid, Sodium Hydroxide, Potassium Hydroxide and Sulphuric and Phosphoric acid mixture) comparison. We show that regular SLE etchants such as Hydrofluoric acid or Potassium Hydroxide are unsuitable materials for selective sapphire laser etching. Meanwhile, a 78% sulphuric and 22% phosphoric acid mixture at 270°C temperature is a good alternative for this process. We present the changes in the material after the separate processing steps. Finally, a protocol for advanced sapphire structure formation and a few exemplary structures are presented.

This paper analyses and evaluate the precision and the accuracy the capability of low-cost terrestrial photogrammetry by using many digital cameras to construct a 3D model of an object. To obtain the goal, a building façade has imaged by two inexpensive digital cameras such as Canon and Pentax camera. Bundle adjustment and image processing calculated by using Agisoft PhotScan software. Several factors will be included during this study, different cameras, and control points. Many photogrammetric point clouds will be generated. Their accuracy will be compared with some natural control points which collected by the laser total station of the same building. The cloud to cloud distance will be computed for different comparison 3D models to investigate different variables. The practical field experiment showed a spatial positioning reported by the investigated technique was between 2-4cm in the 3D coordinates of a façade. This accuracy is optimistic since the captured images were processed without any control points.

This paper explores the influence of various camera settings on the quality of 3D reconstructions, particularly in indoor crime scene investigations. Utilizing Neural Radiance Fields (NeRF) and Gaussian Splatting for 3D reconstruction, we analysed the impact of ISO, shutter speed, and aperture settings on the quality of the resulting 3D reconstructions. By conducting controlled experiments in a meeting room setup, we identified optimal settings that minimize noise and artifacts while maximizing detail and brightness. Our findings indicate that an ISO of 200, a shutter speed of 1/60 seconds, and an aperture of f/3.5 provide the best balance for high-quality 3D reconstructions. These settings are especially useful for forensic applications, architectural visualization, and cultural heritage preservation, offering practical guidelines for professionals in these fields. The study also highlights the potential for future research to expand on these findings by exploring other camera parameters and real-time adjustment techniques.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

While cycling presents environmental benefits and promotes a healthy lifestyle, the risks associated with overtaking maneuvers by motorized vehicles pose significant hindrances for many potential cyclists. Large-scale analysis of overtaking maneuvers could inform traffic researches and city planners on how to reduce these risks by better understanding these maneuvers. Drawing from the fields of sensor-based cycling research and of LiDAR-based traffic data sets, this paper provides a step towards addressing these safety concerns by introducing the Salzburg Bicycle 3d (SaBi3d) data set, consisting of LiDAR point clouds capturing car-to-bicycle overtaking maneuvers. The data set, collected using a LiDAR-equipped bicycle, facilitates detailed analysis of a large quantity of overtaking maneuvers without the need for manual annotation through enabling automatic labeling by a neural network. Additionally, a benchmark result for 3d object detection using a competitive neural network is provided as a baseline for future research. The SaBi3d data set is structured identically to the nuScenes data set, and therefore offers compatibility with numerous existing object detection systems. This work provides valuable resources for future researchers to better understand cycling infrastructure and mitigate risks, thus promoting cycling as a viable mode of transportation.

3D cell cultures have improved the evaluation of drugs for cancer therapy, due to their high similarity to solid tumors. In melanoma, autophagy appears to show a dual role depending on the progression of the disease. p62 protein has been proposed for the evaluation of autophagic flux since its expression is an indicator of the state of autophagy. Pentoxifylline (PTX) and Norcantharidin (NCTD) are drugs that have been shown to have anticancer effects in various types of cancer. In this work, B16F1 mouse melanoma cell line was used, from which two-dimensional (2D) monolayer cultures and three-dimensional (3D) organoids were carried out using the hanging drop technique. The expression of p62 was determined by western blot and immunofluorescences. Our results indicate that pentoxifylline reduces p62 expression in both types of culture. While Norcantharidin increases its expression in 3D cultures at 24 h. Therefore, these drugs could have a potential therapeutic use for the regulation of autophagy in melanoma, depending on the state of evolution of the disease.

This research presents the creation of a Virtual Reality experience for the Balzi Rossi museum, commemorating the centenary of Prince Albert I Grimaldi's archaeological work at the site. The project, a collaboration between the University of Genoa's 3D Lab Factory, Eurodrone, and the Balzi Rossi archaeological museum, aims to preserve and convey the site's heritage through advanced VR technology. Initially employing Unreal Engine 4, the team used photogrammetry for 3D reconstruction of the "Caviglione" and "Florestano" caves, notable for their ancient rock engravings. This first VR model, despite hardware limitations, provided an interactive exploration of the site. The subsequent development phase utilized Unreal Engine 5, incorporating Nanite technology for enhanced visual fidelity. This advancement resulted in a more detailed and immersive VR experience, presenting the Balzi Rossi cliff across different historical periods, including the Würm glaciation. Key to this phase was optimizing the VR experience for performance, focusing on stable frame rates and minimizing motion sickness, and integrating a multi-lingual interface for broader accessibility. Since November 2023, the VR setup at the Balzi Rossi Museum has been an educational and interactive feature, enabling visitors to explore the site's history virtually. This research demonstrates the potential of VR in cultural heritage preservation and education, providing a foundation for future technological improvements in the field.

When a limb suffers a fracture, rupture, or dislocation, it is traditionally immobilized with plaster. This may induce discomfort in the patient, excessive itching and sweating, which creates the growth of bacteria, leading to an unhygienic and difficulty to keep clean from treatment. Furthermore, if the plaster remains for a long period, it may cause lesions in the joints and ligaments. To overcome all these disadvantages, orthoses have emerged as important medical devices to help patients in rehabilitation, as well as for self-care of deficiencies in clinics and daily life. Traditionally, these devices are produced manually, which becomes time-consuming and error prone. From another point-of-view, it is possible to use imageology (X-ray or computed tomography) to scan the human body; a process that may help orthoses manufacturing but induces radiation to the patient. To overcome this great disadvantage, several types of 3D scanners, without any kind of radiation have emerged. This article describes the use of various types of scanners capable of digitizing the human body, to produce custom orthoses. Studies have shown that photogrammetry is the most used and most suitable 3D scanner for the acquisition of the human body in 3D. With this evolution of technology, it is possible to decrease the scanning time and it will be possible to introduce this technology in clinical environment.

Geotechnical investigation is an important site characterization process in engineering construction. Excavation pits and boreholes are popular geotechnical investigation methods for accessing subsurface soil and rock characteristics. Although they are accurate, they are limited to the discrete locations where tests are carried out. The demand for 3D representation has been increasing as an alternative for improved visualization of geotechnical investigations. This study developed a procedure for 3D modelling of geotechnical investigations using open-source software. It improves 3D visualization of geotechnical investigations and characterization of accuracy and uncertainty assessment. Presently, most geotechnical investigations do not regularly report uncertainty assessment despite its importance in risk analysis of the investigations. The procedure developed in this study was tested in a proposed site for construction of an Inland Container Depot where it depicted geotechnical soil properties with more than 80% accuracy on holdout samples. It was able to model both horizontal and vertical variations of the soil properties with quantification of uncertainty. More testing and wide applications are recommended.

Melanoma is a highly aggressive type of skin cancer produced by malignant transformation of melanocytes and it is usually associated with a poor prognosis. Clinically, melanoma has several stages associated with migration and invasion of the cells through the skin layers, rapid cell spreading and formation of tumors in multiple organs. The main problem is the emergence of resistance of melanoma to the applied methods of treatment, thus it is of primary importance to find more crucial signaling pathways that control the progression of this type of cancer and could be targeted to prevent melanoma spreading. The main life-threatening stage of melanoma is metastasis formation, and 3D cell spheroids are better suited for the study of this process. Using a combinative approach (RT-PCR, immunofluorescence, patch-clamp and calcium imaging) we showed the functional expression of mechanosensitive Piezo1 channels in SK-MEL-2 aggressive melanoma cell line. We found that chemical activation of Piezo1 by its selective agonist Yoda1 completely prevents melanoma spheroid formation, and could be considered as a novel approach for the prevention of melanoma development.

Free-edge effect is one of the factors affecting the mechanical properties of three-dimensional woven composites under tensile load. However, current research is relatively poorly understood regarding the effect of free-edge on the stiffness and strength of the material. This paper aims at examining the influence of free-edge effect on the mechanical properties of 3D woven composites under tension through experimental and simulation mathods. The three-dimensional DIC technique is used to collect the full-field strains on the specimen surface during the test, and the stress-strain differences in different regions in the width direction are analyzed, and the overlap of the curves in each region is found to be high. Experimental studies are conducted on specimens of different widths (within the range of 15-20 mm), and the results indicate that the differences in mechanical properties of 3D woven composites under tension loading in this width range are not significant. A progressive damage finite element model is developed for calculation and compared with experimental results.

The increased accessibility of drone technology and the wide use of Structure from Motion 3D scene reconstruction have transformed the approach for mapping inaccessible slopes undergoing active rockfalls. The Poggio Baldi landslide offers the possibility for many of these techniques to be deployed and integrated with the aim of defining a suitable workflow for the analysis of hazards in mountainous regions. The generation of multitemporal digital slope twins (2016 – 2019), informed a rockfall trajectory analysis that was carried out with a physical-based GIS model. We tested the rockfall scenario reconstructed and calibrated on the analysis of the rock mass characteristics and the geometrical and physical constraints given by the multi-temporal analysis of the SfM point clouds. This time-independent rockfall hazard analysis is a critical component to any subsequent holistic risk analysis on this case study, and any potential similar mountainous setting.

Beyond semantic segmentation,3D instance segmentation(a process to delineate objects of interest and also classifying the objects into a set of categories) is gaining more and more interest among researchers since numerous computer vision applications need accurate segmentation processes(autonomous driving, indoor navigation, and even virtual or augmented reality systems…) This paper gives an overview and a technical comparison of the existing deep learning architectures in handling unstructured Euclidean data for the rapidly developing 3D instance segmentation. First, the authors divide the 3D point clouds based instance segmentation techniques into two major categories which are proposal based methods and proposal free methods. Then, they also introduce and compare the most used datasets with regard to 3D instance segmentation. Furthermore, they compare and analyze these techniques performance (speed, accuracy, response to noise…). Finally, this paper provides a review of the possible future directions of deep learning for 3D sensor-based information and provides insight into the most promising areas for prospective research.

Polystyrene as a thin film on arbitrary substrates or pellets form defective graphene films or powders that can be dispersed in water and organic solvents. The materials were characterized by visible absorption, Raman and X-ray photoelectron spectroscopy, electron and atomic force microscopy and electrochemistry. Raman spectra of these materials show the presence of the expected 2D, G and D peaks at 2750, 1590 and 1350 cm^-1, respectively. The relative intensity of the G vs. the D peak is taken as a quantitative indicator of the density of defects in the G layer.

Osteoarthritis (OA) is a joint disease involving cartilage degeneration. This study aimed to compare properties of chondrocytes from less-affected (LA-Cartilage) and severely-affected (SA-Cartilage) of human OA articular cartilage. Based on Dougados classification, OA cartilage was classified into two groups; less-affected (Grade 0–1) and severely-affected (Grade 2–3). Chondrocytes from each group were cultured until passage (P) 4. Growth, migration, stem cell properties and chondrogenic properties under normal and inflammatory conditions, and the formation of in vitro 3D cartilage tissues were compared between groups. The growth and migratory properties of LA-chondrocytes and SA-chondrocytes were similar, except that the migration rate of SA-chondrocytes was significantly higher at P0 compared to LA-chondrocytes. Both LA-chondrocytes and SA-chondrocytes expressed mesenchymal stem cell markers and tri-lineage differentiation, but the expression of stem cell markers decreased significantly with increasing passage number. Exposure to inflammatory conditions induced distinct morphological changes and significant increases in expression of SOX9 at P4 and MMP3 at P1 for LA-chondrocytes. LA-chondrocytes and SA-chondrocytes able to develop into in vitro 3D constructs, but SA-chondrocytes exhibited superior cartilage-like properties. Chondrocytes from both less- and severely-affected regions are suitable to be used in clinical applications, however, chondrocytes from severely-affected regions could be a more favorable cell source.

Numerical weather prediction is an initial-value problem, for determination of the initial conditions, there are many methods and one of the most classical methods is variational methods in three dimensions, or 3D-Var. In this approach, with a defined cost function proportional to the square of the distance between the analysis and both the background and the observations, one can obtain the analysis. In the cost function, the background and the observations are reshaped to vectors; within this step, the order of the background error covariance matrix and the observational error covariance matrix becomes huge, which is not convenient to one to obtain the analysis. In this paper, according to the matrix analysis approach, we put forward some possible improvements to the dimension-reduction algorithm of 3D-Var, so that provide some references for data assimilation.

Background: Wilms tumor (WT) is the main renal tumor in children. SIOP-UMBRELLA Guidelines admit Nephron sparing surgery (NSS) in syndromic patients, and in small (&lt;300 ml) nonsyndromic unilateral WTs, without lymph node involvement, and with a substantial expected remnant renal function, after neoadjuvant chemotherapy. We report our prechemotherapy transperitoneal robot-assisted partial nephrectomy (RAPN) in a unilateral non-syndromic Wilms tumor. Methods: A 6-year-old-child showed an exophytic 3.6 cm diameter solid rounding mass involving the upper right renal pole at an incidental abdominal echotomography. CT-scan and abdominal MRI proved no local infiltration neither lymph node involvement was appreciated, suggesting an exophytic mass easily resectable through a NSS robotic approach, with a low risk of rupture and no subverted renal anatomy. The preoperative imaging was not suggestive for WT. A virtual 3D reconstruction of the tumor was performed. Results: the oncologic board approved a robot-assisted partial nephrectomy with the intraperitoneal approach. The histopathologic analysis displayed a WT. The patient underwent 10 vincristine-doses adjuvant chemotherapy. 28-months follow-up showed no tumor recurrence. Conclusions: Intraperitoneal RAPN can represent an opportunity for WT and needs to be assessed as a challenging possibility. This case suggests a potential role of prechemotherapy RAPN in the near future for highly selected patients.

In this paper, we present the idea of Self Supervised learning on the Shape Completion and Classification of point clouds. Most 3D shape completion pipelines utilize autoencoders to extract features from point clouds used in downstream tasks such as Classification, Segmentation, Detection, and other related applications. Our idea is to add Contrastive Learning into Auto-Encoders to learn both global and local feature representations of point clouds. We use a combination of Triplet Loss and Chamfer distance to learn global and local feature representations. To evaluate the performance of embeddings for Classification, we utilize the PointNet classifier. We also extend the number of classes to evaluate our model from 4 to 10 to show the generalization ability of learned features. Based on our results, embedding generated from the Contrastive autoencoder enhances Shape Completion and Classification performance from 84.2% to 84.9% of point clouds achieving the state-of-the-art results with 10 classes.

Electric energy has become essential nowadays not only for the daily life of each of us but also for the economy of different countries. The dissemination of geographic information plays an important role in national development as it facilitates communication between managers, investors, and consumers in this sector. Since the management of electricity network data was previously done in Tunisia based on paper maps and plans, the purpose of this article is to present a case of planning based on GIS, Web, and 3D Web GIS, which would have significant positive consequences on this sector from a technical and financial sides with an improvement in customer satisfaction and the creation of an intelligent electricity network which will be a real decision-making tool. This work draws up an inventory of the network MV (Medium Voltage)/LV (Low Voltage) of the region of Medjez El Bab which routes electricity to the big centers of consumption with access to MV/LV subscribers. The analysis of the network's impedance allowed carrying out different scenarios to optimize performance and obtain more realistic routes. Many thematic maps were produced as part of this project (Slope map, Land use map, map of the MV voltage domains, map of the MV/LV transformer stations power, etc.). A three-dimensional virtual city has been developed to visualize the graphical and attribute data for the study area. A Web and 3D Web GIS applications that allows the publication of the interactive maps on the Web as well as the database information have been developed to offer users the possibility of consulting the produced products by internet. Finally, a website related to the study was developed.

Recent advances in the research area of 3D magnetic topological solitons (hopfions) in restricted geometries are reviewed. The description of the magnetic solitons is based on macroscopic micromagnetic approach and the Landau-Lifshitz equation of the magnetization motion. The concepts of the gauge emergent vector potential and emergent magnetic field are widely used to calculate 3D topological charge (the Hopf index) of magnetic textures. The relation of the magnetic hopfions with classical field theory is demonstrated and a special role of the curvilinear toroidal coordinates in description of the hopfions is underlined. The hopfion stability and dynamics in ferromagnetic films and dots are considered. Some critical discussion of calculations of the magnetization emergent magnetic field and the Hopf index of the toroidal magnetic hopfions in restricted geometries is presented.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

In the world of digital avatars, three-dimensional (3D) human models are utilized to replicate real-world appearance and movements with a higher degree of realism compared to traditional 2D representations. Currently, extensive person-specific data capturing and 3D artists are required to create photorealistic avatars of existing people. Determining the 3D pose and articulation of an avatar from 2D images requires complex algorithms, a capability commonly found in the Visual Effects (VFX) industry but not readily available elsewhere. Hence, this study proposes an approach to generate 3D avatar from a 2D image of a person with uncanny resemblance and an accurate depiction of the subject’s likeness. The proposed approach, PIFu+CycleGAN, combines Pixel-aligned Implicit Function (PIFu) and cycleGAN for textured avatar construction. PIFu is specifically used to capture intricate details and arbitrary topology. Additionally, the hourglass architecture-based module is utilized for T-pose estimation for predicting the initial geometry and shape. Evaluating the proposed approach on the benchmark RenderPeople dataset, it outperforms the state-of-the-art models with values of 1.53 and 1.50 for the Chamfer and P2S distance, respectively. This indicates the creation of high-quality 3D meshes with promising textures, which are of exceptional quality and suitable for animation.

In the history, architects, engineers or artists traditionally visualized architectural, urban planning, urban design, or landscape design projects with physical models in a smaller scale to represent their ideas. The biggest problems of traditional materialistic models are the long production time and limitation of mobility. Thanks to advancements in digital technology, 3D models can now be generated easily from 2D blueprints using computer software. However, eventually the digitalized approach could not replace the whole industry of making physical models, because of a lack of stereoscopic 3D imaging of space and structures. In this study, we discuss two points: the normal procedure of visualizing 3D models in urbanism and architecture design projects; and proposal of the stereographic hologram visualization for 3D models created with CHIMERA hologram printer as a new approach to solve all the problems in spatial projects visualization of both digitalized and physical models. The experiment's results indicate that tabletop holograms' visualization quality can potentially replace traditional methods in the near future. Moreover, the input data for this method can be seamlessly integrated into current architectural and urban design workflows, making holograms a promising approach for 3D immersive content in this field.

The evaluation of nanostructured biomaterials and medicines is associated with 2D cultures that provide insight into the biological mechanisms at the molecular level, while critical aspects of the tumor microenvironment (TME) are provided by the study of animal xenograft models. More realistic models that can histologically reproduce human tumors are provided by tissue engineering methodologies of co-culturing cells of varied phenotypes, to provide 3D tumor spheroids that recapitulate the dynamic TME in 3D matrices. The novel approaches of 3D tumor models are combined with tumor tissue engineering (TTE) scaffolds including hydrogels, bioprinted materials, decellularized tissues, fibrous and nanostructured matrices. This review focuses on the use of nanostructured materials in cancer therapy and regeneration, and the development of realistic models for studying TME molecular and immune characteristics. Tissue regeneration is an important aspect of TTE scaffolds for restoring the normal function of the tissues, while providing cancer treatment. Thus, this article reports recent advancements on the development of 3D TTE models for antitumor drug screening, studying of tumor metastasis, and tissue regeneration. Also, this review identifies the great opportunities of 3D TTE scaffolds in the evaluation of the immunological mechanisms and processes involved in the application of immunotherapies.

Immediate load of full-arch rehabilitations over implants, specially over 4 implants are very well documented in the literature. More recently, the use of computed surgical guides to help the planning and the execution of these treatments, in many situations without the need of raising a flap, and diminishing the appearance of hematomas, bleeding and with less trauma to the patient has gained preference among implantologists. The objective of this case report is to show a clinical case of an immediate load full-arch fixed rehabilitation over 4 implants produced by 3D printing manufacturing technology, and placed with a computed surgical guide, in the same appointment, and the 24 months follow-up. The patient returned after 3 months to replace the immediate temporary fixed prosthesis for a new one, with metallic bar, better teeth and more delicate. Soft and hard tissue around the implants seemed to be stable, without signs of inflammation, either on the 3 or the 24 months follow-up. 3D printing of implants by direct metal laser sintering is a technology that seems to be promising for oral implantology, with solid studies showing reliable results, as seen in this single case. More clinical studies are necessary to testify its efficacy.

Characters are one of the most important elements in composing digital animation. The appear-ance and voice of a character should be designed to express the personality and values of the character. However, it is not easy for animation producers to harmoniously match the appear-ance and voice of a character. Advances in deep learning technology have made it possible to overcome this limitation. To achieve this, firstly, an audio-visual dataset of characters is required. In this study, we construct and verify a Korean audio-visual dataset consisting of frontal face im-ages of various characters and short voice clips. We developed an application that can automati-cally extract the frontal face image and a short voice clip of a character by collecting videos up-loaded to YouTube. Through this, a dataset consisting of a total of 1,522 face images and a total of 7,999 seconds of voice clips was built based on 490 characters. Furthermore, we automatically la-bel characters by gender and age to validate the dataset. The dataset built in this study is expected to be used in various deep learning fields, such as classification, generative adversarial networks, and speech synthesis.

The 3D reconstruction of vermiculite-based sealing material was carried out based on CT scanning experiments and Avizo software. The precision and representation of the reconstructed digital core were tested by calculating the pore structure parameters and comparing them with the experimental results of mercury compression. Avizo is a perfect interface with Fluent software to perform micro-scale seepage simulation to explore the distribution of pressure and velocity fields during fluid transport. In this paper, a new approach is proposed to study the penetration leakage of non-metallic gaskets by using equivalent pore networks.

The three-dimensional Ising model on the m$\times$n$\times$l cubic lattice with the screw boundary condition along the ${\bf X}$ direction and the periodic boundary conditions along both ${\bf Y}$ and ${\bf Z}$ directions is exactly solved by using the $2^{mn}$-dimensional representation of the rotation group in $2mn$-dimensions, similar to the Kaufman's spinor approach in two dimensions. The exact partition function is obtained from two sets of $2^{mn-1}$ eigenvalues of the $2^{mn}$-dimensional transfer matrix {\bf V} corresponding to the even and odd eigenvectors, respectively. Such the eigenvalues are determined by the angles of the 2mn-dimensional rotation associated with {\bf V}.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

Existing methods for 3D human pose estimation mainly divide the task into two stages. The first stage identifies the 2D coordinates of the human joints in the input image, namely the 2D human joint coordinates. The second stage uses the results from the first stage as input to recover the depth information of human joints from the 2D human joint coordinates to achieve 3D human pose estimation. However, the recognition accuracy of the two-stage method relies heavily on the results of the first stage and includes too many redundant processing steps, which reduces the inference efficiency of the network. To address these issues, we propose the EDD, a fully End-to-end 3D human pose estimation method based on transformer architecture with Dual Decoders. By learning multiple human poses, the model can directly infer all 3D human poses in the image using a pose decoder, and then further optimize the recognition result using a joint decoder based on the kinematic relations between joints. With the attention mechanism, this method can adaptively focus on the most relevant features to the target joint, effectively overcoming the feature misalignment problem in the human pose estimation task and greatly improving the model performance. Any complex post-processing step, such as non-maximum suppression, is eliminated, further improving the efficiency of the model. The results show that the method achieves an accuracy of 87.4% on the MuPoTS-3D dataset, significantly improving the accuracy of end-to-end 3D human pose estimation methods.

The rapid development of electrochemical CO2 reduction offers a promising route to convert in-termittent renewable energy into products of high value-added fuels or chemical feedstocks. However, low faradaic efficiency, low current density, and a narrow potential range still limited the large-scale application of CO2RR electrocatalyst. Herein, monolith 3D bi-continuous nano-porous Bismuth (np-Bi) electrodes are fabricated via a simple one-step electrochemical dealloying strategy from Pb-Bi binary alloy. The unique bi-continuous porous structure ensures highly effective charge transfer, meanwhile the controllable millimeter-size geometric porous structure enables easy catalyst adjustment to expose highly suitable surface curvatures with abundant reactive sites. This results in a high selectivity of 92.6% and superior potential window (400 mV, selectivity >88%) for electrochemical reduction of carbon dioxide to formate. Our scalable strategy provides a feasible pathway for mass-producing high-performance and versatile CO2 electrocatalysts.

A key component of efforts to identify the biological and drug-specific aspects that contribute to therapeutic failure or unexpected exposure-associated toxicity is the study of drug-intestinal barrier interactions. While methods supporting such assessments are widely described for human therapeutics, there is relatively little information available for similar evaluation in support of veterinary pharmaceuticals. There is, therefore, a critical need to develop novel approaches for evaluating drug-gut interactions in veterinary medicine. Three-dimensional (3D) organoids can address these difficulties in a reasonably affordable system that circumvents the need for more invasive in vivo assays in live animals. However, a first step in the development of such systems is understanding organoid interactions in a 2D monolayer. Given the importance of orally administered medications for meeting the therapeutic need of companion animals, we demonstrate growth conditions under which canine colonoid-derived intestinal epithelial cells survive, mature, and differentiate into confluent cell systems with high monolayer integrity. We further examine the applicability of this canine colonoid-derived 2D model to assess the permeability of three structurally diverse, passively absorbed β-blockers (e.g., propranolol, metoprolol, and atenolol). Both absorptive and secretive apparent permeability (Papp) of these drugs at two different pH conditions were evaluated in canine colonoid-derived monolayers and were compared with that of Caco-2 cells. This proof-of-concept study provides promising preliminary results with regard to the utility of canine-derived organoid monolayers for species-specific assessments of therapeutic drug passive permeability.

Smart health applications have received significant attention in recent years. Novel applications hold significant promise to overcome many of the inconveniences faced by persons with disabilities throughout daily living. For people with blindness and low vision (BLV), environmental perception is compromised, creating myriad difficulties. Precise localization is still a gap in the field and is critical to safe navigation. Conventional GNSS positioning cannot provide satisfactory performance in urban canyons. 3D mapping-aided (3DMA) GNSS may serve as an urban GNSS solution, since the availability of 3D city models has widely increased. As a result, this study developed a real-time 3DMA GNSS-positioning system based on state-of-the-art 3DMA GNSS algorithms. Shadow matching was integrated with likelihood-based ranging 3DMA GNSS, generating positioning hypothesis candidates. To increase robustness, the 3DMA GNSS solution was then optimized with Doppler measurements using factor graph optimization (FGO) in a loosely-coupled fashion. This study also evaluated positioning performance using an advanced wearable system’s recorded data in New York City. The real-time forward processed FGO can provide a root-mean-square error (RMSE) with about 21 m. The RMSE drops to 16 m when the data is post-processed with FGO in a combined direction. Overall results show that the proposed loosely-coupled 3DMA FGO algorithm can provide a better and more robust positioning performance for the multi-sensor integration approach used by this wearable for persons with BLV.

Along with the popularity of the Internet, people are exposed to more and more ways of micro-videos, and a huge amount of micro-video data has emerged. micro-videos have gradually become the Internet content preferred by the public, and a large number of micro-video apps have also emerged, such as Tiktok and Kwai. Intelligent classification and mining of micro-videos can greatly enhance user experience, improve business operation efficiency and enhance user experience. Through deep intelligent analysis and mining of micro-videos, important information in micro-videos can be extracted to provide an important basis for beautifying videos, content appreciation, video recommendation, content search, etc. In the past, content understanding for short videos often used human work annotation, but in recent years, with the great success of deep convolutional neural networks in image recognition, short video content understanding based on this method has gradually developed. Nowadays, most recognition algorithms extract the feature representation of each frame independently and then fuse them. However, while extracting the feature representation, some low-level semantic features are lost, which makes the algorithm unable to accurately distinguish the category of the video. At present, the algorithm of micro-video recognition based on deep learning has surpassed the iDT algorithm, making these traditional methods fade out of people’s view. In this paper according to the micro-video classification task, a new network model is proposed to concatenate features of each modality into the overall features of various modalities through the network, and then fuse the various modal features with the attention mechanism to obtain the whole micro-video features, which will be used for classification. In order to verify the effectiveness of the algorithm proposed in this paper, experiments are conducted in the public dataset, and it is shown the effectiveness of our model.

This article describes the methodology used to identify the mathematical model that describes the correlations between the input parameters of an experiment and the parameters being followed. As a technological process, the aerodynamic separation was chosen, respectively, the behavior of a solid particle within an ascending vertical airflow. The experimental data obtained were used to identify two parameters, the average linear velocity, and the angular velocity, and through the Table Curve 3D program was developed a mathematical model which describes the dependence between the input parameters (the shape and size of the solid particle and the velocity of the airflow) and the monitored parameters. In order to determine a single mathematical equation that describes as accurately as possible the correlation between the input variables and those obtained, a pyramid-type analysis was designed. The determination of the mathematical equation started from the number of equations generated by the Table Curve 3D program, then the equations with a correlation coefficient greater than 0.85 were chosen, and finally, the common equations were identified. Respecting the working methodology was identified one equation which has for the average linear velocity a correlation coefficient r2 between 0.88-0.99 and 0.86-0.99 for the angular velocity.

Radar observation data with high temporal and spatial resolution are used in the data assimilation experiment to improve precipitation forecast of a numerical model. The numerical model considered in this study is Weather Research and Forecasting (WRF) model with double-moment 6-class microphysics scheme (WDM6). We calculated radar equivalent reflectivity factor using higher resolution WRF and compared with radar observations in South Korea. To compare the precipitation forecast characteristics of three-dimensional variational (3D-Var) assimilation of radar data, four experiments are performed based on different precipitation types. Comparisons of the 24-h accumulated rainfall with Automatic Weather Station (AWS) data, Contoured Frequency by Altitude Diagram (CFAD), Time Height Cross Sections (THCS), and vertical hydrometeor profiles are used to evaluate and compare the accuracy. The model simulations are performed with and with-out 3D-VAR radar reflectivity, radial velocity and AWS assimilation for two mesoscale convective cases and two synoptic scale cases. The radar data assimilation experiment improved the location of precipitation area and rainfall intensity compared to the control run. Especially, for the two convective cases, simulating mesoscale convective system was greatly improved.

The initial stability after implantology is paramount to the survival of the dental implant and the surface roughness of the implant plays a vital role in this regard. The characterisation of surface topography is a complicated branch of metrology, with a huge range of parameters available. Each parameter contributes significantly towards the survival and mechanical properties of 3D-printed specimens. The purpose of this paper is to experimentally investigate the effect of surface roughness of 3D-printed dental implants and 3D-printed dogbone tensile samples under areal height (Ra) parameters, amplitude parameters (average of ordinates), skewness (Rsk) parameters and mechanical properties. During the experiment, roughness values were analysed and the results showed that the skewness parameter demonstrated a minimum value of 0.596%. The 3D-printed dental implant recorded Ra with a 3.4 mm diameter at 43.23% and the 3D-printed dental implant with a 4.3 mm diameter at 26.18%. Samples with a complex geometry exhibited a higher roughness surface, which was the greatest difficulty of additive manufacturing when evaluating surface finish. The results show that when the ultimate tensile stress (UTS) decreases from 968.35 MPa to 955.25 MPa, Ra increases by 1.4% and when UTS increases to 961.18 MPa, Ra increases by 0.6%. When the cycle decreases from 262142 to 137433, Ra shows that less than a 90.74% increase in cycle is obtained. For 3D-printed dental implants, the higher the surface roughness, the lower the mechanical properties, ultimately leading to decreased implant life and poor performance.

Three-dimensional (3D) printing techniques have received considerable focus in the area of bone engineering due to its precise control in the fabrication of complex structures with customizable shapes, internal and external architectures, mechanical strength, and bioactivity. In this study, we design a new composition biomaterial consisting of polylactic acid (PLA), and halloysite nanotubes (HNTs) loaded with zinc nanoparticles (PLA+H+Zn). The hydrophobic surface of the 3D printed scaffold was coated with two layers of fetal bovine serum (FBS) on the sides and one layer of NaOH in the middle. Additionally, a layer of gentamicin was coated on the outermost layer against bacterial infection. Scaffolds were cultured in standard cell culture medium without the addition of osteogenic medium. This surface modification strategy improved material hydrophilicity and enhanced cell adhesion. Pre-osteoblasts cultured on these scaffolds differentiated into osteoblasts and proceeded to produce a type I collagen matrix and subsequent calcium deposition. 3D printed scaffolds formed from this composition possessed high mechanical strength and showed an osteoinductive potential. Furthermore, the external coating of antibiotics not only preserved the previous osteogenic properties of the 3D scaffold but also significantly reduced bacterial growth. Our surface modification model enabled the fabrication of a material surface that was hydrophilic and antibacterial, simultaneously, with an osteogenic property. The designed PLA+H+Zn may be a viable candidate for the fabrication of customized bone implants.

Paclitaxel is a natural, highly lipophilic anti proliferative drug widely used in medicine. We have studied the release of tritium-labeled paclitaxel (³H-PTX) from matrices destined for the coating of vascular stents and produced by the electrospinning method from the solutions of polycaprolactone (PCL) with paclitaxel (PTX) in hexafluoisoropropanol (HFIP) and/or solutions of PCL with PTX and human serum albumin (HSA) in HFIP or HIFP-dimethyl sulphoxide (DMSO) blend. The release of PTX has been shown to depend on the solvent and the composition of electrospinning solution, as well as the composition of the surrounding medium, particularly the concentration of free PTX and PTX-binding biomolecules present in human serum. It was shown that 3D matrices can completely release PTX without weight loss. Two-phase PTX release from optimized 3D matrices was obtained: ~27% of PTX was released in the first day, another 8% were released over the next 26 days. Wherein ~2.8%, ~2.3%, and ~0.25% of PTX was released on day 3, 9, and 27, respectively. Considering PTX toxicity, the rate of its diffusion through the arterial wall, and the data obtained the minimum cytostatic dose of the drug in the arterial wall will be maintained for at least three months.

AbstractWhile the technology is relatively new, low cost 3D printing has impacted many aspects of human life. 3D printers are being used as manufacturing tools for a wide variety of devices in a spectrum of applications ranging from diagnosis to implants to external prostheses. The ease of use and availability of 3D design software and low cost has made 3D printing an accessible manufacturing and fabrication tool in many research laboratories. 3D printers can print materials with varying density, optical character, strength and chemical properties providing platforms for a huge number of strategies that can be chosen for user’s needs. In this review, we focus on applications in biomedical diagnostics and how this revolutionary technique is facilitating development of low cost, sensitive and often geometrically complex tools. 3D printing in fabrication of microfluidics, supporting equipment, optical and electronic components of diagnostic devices is presented. Emerging diagnostic 3D bioprinting as a tool to incorporate living cells or biomaterials into 3D printing is also discussed.

This study aimed to assess the response of 3D printed PLA scaffolds biomimetically coated with apatite on human primary osteoblast spheroids and evaluate the biological response to its association with Bone Morphogenetic Protein 2 (rhBMP-2) in rat calvaria. PLA scaffolds were produced via 3D printing, soaked in simulated body fluid (SBF) solution, and characterized by physical-chemical, morphological, and mechanical properties. The in vitro biological response was assessed with human primary osteoblast (HOb) spheroids. The in vivo analysis was conducted through the implantation of 3D printed PLA scaffolds either alone, covered by apatite (PLA-CaP) or PLA-CaP loaded with rhBMP-2 (PLA-CaP+rhBMP-2) on critical-sized defects (8 mm) of rat calvaria. Increased cell adhesion and in vitro release of growth factors (PDGF, bFGF, VEGF) was observed for PLA-CaP scaffolds when pre-treated with FBS. PLA-CaP+BMP2 presented higher values of newly formed bone (NFB) than other groups at all experimental periods (p&lt;0.05), attaining 44.85% of NFB after 6 months. These findings indicate that functionalization of PLA scaffolds with biomimetic apatite can improve its biological properties in the presence of complex biological media. Its association with BMP2 may enhance bone repair, suggesting this strategy as a promising candidate for bone tissue engineering.

Currently, the number of approved veterinary medicines are limited, and human medications are used off-label. These approved human medications are of too high potencies for a cat or a small dog breed. Therefore, there is a dire demand for smaller doses of veterinary medicines. This study aims to investigate the use of three semi-solid extrusion 3D printers in a pharmacy or animal clinic setting for extemporaneous manufacturing of prednisolone containing orodispersible films for veterinary use. Orodispersible films with adequate content uniformity and acceptance values defined by the European Pharmacopoeia was produced with one of the studied printers, namely, the Allevi 2 bioprinter. Smooth and flexible films, with high mechanical strength, neutral pH, and low moisture content were produced with high correlation between prepared design and obtained drug amount, indicating that the Allevi 2 printer could successfully be used to extemporaneously manufacture personalized doses for animals at the point-of-care.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

Aiming to address the issue that the existing multi-view stereo reconstruction methods have insufficient adaptability to the repetitive patterns and weak textures in the multi-view images, this paper proposes a three-dimensional (3D) reconstruction algorithm based on feature enhancement and weight optimization MVSNet (Abbreviated as FEWO-MVSNet). To obtain accurate and detailed global and local features, we first develop an adaptive feature enhancement approach to obtain multi-scale information from the images. Second, we introduce an attention mechanism and a spatial feature capture module to enable high-sensitivity detection for weak texture features. Third, based on the 3D convolutional neural network, the fine depth map for multi-view images can be predicted and the complete 3D model is subsequently reconstructed. Last, we evaluated the proposed FEWO-MVSNet through training and testing on the DTU, BlendedMVS, and Tanks&amp;Temples datasets. The results demonstrate significant superiorities of our method for 3D reconstruction from multi-view images, with our method ranking first in accuracy and second in completeness when compared to the existing representative methods.

This paper reviews the measurement challenges associated with 3D scanning techniques in civil engineering. It explores the practical aspects of scanning buildings and complex surfaces through various case studies. The paper details the conventional use of Terrestrial Laser Scanning (TLS) for reconstructing the technical documentation of a hall. It then describes an unconventional application of this technique for measuring an ETICS (External Thermal Insulation Composite System) wall, aiming to detect microdeformations caused by environmental factors controlled within a climatic chamber. The measurements of the insulated wall were subsequently repeated using a metrological grade laser scanner. Numerical data was analyzed with inspection engineering methods. This approach yielded qualitative and quantitative results. Although the qualitative results were consistent, the quantitative data revealed some inconsistencies. To address discrepancies in the quantitative data, a comparative analysis was performed, which highlighted critical findings and areas of divergence.

Human Papillomavirus (HPV) related cancers account for a large percentage of cancers. The tumor microenvironment (TME) is a complex structure and contributes significantly to tumor development, progression, and invasion. The TME is particularly pronounced in HPV-related cancers and HPV is known to influence the TME. In cancer research, there is an urgent need for new models to deepen our understanding of the pathophysiology of the disease and to facilitate the development of innovative therapies. In this context, 3D cell culture has emerged as a promising method in cancer research, that offers significant potential compared to conventional approaches. 3D modelling can produce results that are more consistent with clinical outcomes without the ethical concerns and problems of animal models. In this review, our aim is to discuss the tumor microenvironment in HPV-related cancers and demonstrate the importance of advancing 3D cell culture models for this purpose.

Additive manufacturing (AM), commonly known as 3D printing, has emerged as a transformative technology in supply chain management (SCM). This abstract explores how AM influences various aspects of SCM, including inventory management, production processes, and logistics. By enabling on-demand production and reducing reliance on traditional manufacturing methods, AM minimizes inventory costs and enhances customization capabilities. It also facilitates localized production, which can reduce lead times and transportation costs. The integration of AM into SCM fosters greater flexibility and resilience, allowing businesses to respond more swiftly to market changes and disruptions. This study highlights both the opportunities and challenges associated with adopting AM, emphasizing the need for strategic adjustments to fully leverage its potential in modern supply chains.

Bladder cancer (BC) is one of the most lethal genitourinary malignancies owing to its propensity for recurrence and poor survival. The biochemical pathway, signal transducer and activator of transcription 3 (STAT3), has gained significance as a molecular pathway that promotes proliferation, invasion, and chemoresistance. In this study, we explored the targeting of STAT3 with TTI-101 and SH5-07 in bladder cancer (BCa) and elucidated the mechanisms in three-dimensional (3D) spheroid and tumoroid models. We optimized the growth of spheroids from human, rat, and mouse BCa cell lines (J82, NBT-II, and MB49, respectively), and tumoroids from BBN (N-butyl-N-(4-hydroxybutyl)-nitrosamine) induced rat bladder tumors. Cell viability was assessed using MTT and trypan blue assays. ATP production, ROS production, and calcium AM (CA)/EtBr staining were used to measure the spheroid and organoid inhibition and mitochondrial function. Western blot analysis was performed to evaluate the pharmacodynamic markers involved in cell proliferation, apoptosis, cancer stem cells (CSCs), and STAT3 signaling in BCa. We found that targeting STAT3 (using TTI-101 and SH5-07) significantly reduced the proliferation of BCa spheroids, and tumoroids, which was accompanied by decreased expression of pSTAT3, Cyclin D1, and PCNA. Our data also demonstrated that treatment with STAT3 inhibitors induced ROS production and cell death in BCa spheroids and organoids. STAT3 inhibition induced cell death was associated with the activation of caspase 3/7 and PARP cleavage. Moreover, TTI-101 and SH5-07 targets cancer stem cells by downregulating the expression of CD44 and CD133 in 3D models. This study provides the first evidence for the prevention of bladder cancer with small-molecule inhibitors TTI101 and SH5-07 via suppression of CSCs and STAT3 signaling.

A comparative analysis between Bidirectional Evolutionary Structural Optimization (BESO) and Smoothing-ESO (SESO), simultaneously considering Reliability-Based Topology Optimization (RBTO) and the structure's self-weight in the case of three-dimensional elasticity, is presented in this study. Due to the important role of the existence of uncertainties in making the structural design more realistic, geometry, volumetric fraction, modulus of elasticity, compliance, and loading are considered random variables with normal probability distribution. When adopting the First Order Reliability Method (FORM), the failure probability is calculated based on the reliability index. Furthermore, considering the influence of self-weight in problems involving large structures in civil engineering, especially in the case of bridges, makes the optimal configuration more reliable for design. A series of examples are covered to validate the methods presented, showing their efficiency and robustness.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.

In the last decade, three-dimensional (3D) printing has allowed the field of complex microfluidic channels to expand rapidly towards channels with variable cross-sections (i.e., beyond simple rounded media with a constant diameter) and channels. Whose trajectory can be outside a single plane and has gained numerous macro- and nanoscale manufacturing advances. Three-dimensional printing is being explored for various biomedical applications and the fabrication of nanomedicines using additive manufacturing techniques. Employing 3D-printed templates for macro-to-micro interfacing, a passively operated microfluidic device was designed. The research seeks to fabricate a biodevice that enables insulin microdosing, creating a subsystem like a microvalve and a microchannel matrix using additive manufacturing techniques. Our systems feature designs that enhance fluid dynamics without affecting the stability of the insulin. We propose using Humalog insulin in tropical climates (up to 30°C) without refrigeration for 28 days. The microvalve has a spiral trajectory with four outlet channels distributed along it. These channels align with the microchannels organized in a 10 mm x 15 mm matrix with 25 microchannels, each with a 770 µm internal diameter. The system delivers a dose of 2,3 mL in 6 minutes. We designed these systems for insulin micro-dosing, but they can also serve similar devices for other drugs.

To improve the measurement accuracy of three-dimensional rotation angle of the spherical joint, a novel approach is proposed in this study, which combines the magnetic detection by Hall sensor and surface feature identification by eddy current sensor. Firstly, a permanent magnet is embedded in the ball head of spherical joint, and Hall sensors are set and distributed in the ball socket to measure the variation of magnetic flux density when spherical joint rotating, which are related to 3D rotation angle. In order to further improve measurement accuracy and robustness, we also set grooves on the ball head and use eddy current sensors to synchronously identify the rotation angle of the ball head. After the combination of two signals is adopted, a measurement model is established using the RBF neural network by training, and realized real-time measurement of the 3D rotation angle of spherical joint. The feasibility and superiority of this method are validated through experiments. The experimental results indicated that the measurement accuracy is promoted substantially compared to the preliminary measurement scheme based on spherical coding, the average measurement error of single axis is reduced by 9'9". The root mean square errors for the measurement of 3D rotation angles in this proposed method are as follows: the pitch angle α has an error of 1'8", the yaw angle β has an error of 2'15", and the roll angle γ has an error of 29'6".

With increasing demand from unmanned driving and robotics, more attention has been paid to point cloud-based 3D object accurate detection technology. However, due to the sparseness and irregularity of the point cloud, the most critical problem is how to utilize the relevant features more efficiently. In this paper, we proposed a point-based object detection enhancement network to improve the detection accuracy in the 3D scenes understanding based on the distance features. Firstly, the distance features are extracted from the raw point sets and fused with the raw features about reflectivity of the point cloud to maximizing the use of information in point cloud. Secondly, we enhanced the distance features and raw features that we collectively refer to them as self-features of the key points in Set Abstraction (SA) layers with the self-attention mechanism, so that the foreground points can be better distinguished from the background points. Finally, we revised the group aggregation module in SA layers to enhance the feature aggregation effect of key points. We conducted experiments on the KITTI dataset and nuScenes dataset and the results show the enhancement method proposed in this paper has excellent performance.

In the realm of autonomous vehicle environment perception, the primary objective of point cloud target detection is to swiftly and accurately identify three-dimensional objects from point cloud data. To meet this requirement, the prevalent network architecture employed in the industry is the voxel-based PointPillars model. Nonetheless, this model faces challenges in maintaining detection accuracy when objects are obscured or diminutive in size. In response to this issue, we introduce AGPNet, a novel model that seamlessly integrates four key modules: Data Augmentation, Dynamic Graph CNN, Pillar Feature Net, and Detection Head (SSD). The Data Augmentation module enhances the adaptability of point cloud data to complex and ever-changing real-world environments. The Dynamic Graph CNN module endows the network structure with geometric features, which encapsulate not only the point itself but also its adjacent points. The Pillar Feature Net module translates three-dimensional point cloud data into pseudo-image data through the utilization of voxels. Subsequently, the Detection Head (SSD) module leverages this pseudo-image data to conduct target detection of three-dimensional objects. Our experiments, conducted on the KITTI dataset, demonstrate that our proposed method boosts object detection accuracy by 6-7 percentage points compared to the PointPillars model, while maintaining similar detection times.

We present a near real-time solution for 3D reconstruction from aerial images captured by consumer UAVs. Our core idea is to simplify the multi-view stereo problem into a series of two-view stereo matching problems. Our method applies to UAVs equipped with only one camera and does not require special stereo-capturing setups. We found that the neighboring two video frames taken by UAVs flying at a mid-to-high cruising altitude can be approximated as left and right views from a virtual stereo camera. Leveraging GPU-accelerated real-time stereo estimation, efficient PnP correspondence solving algorithms and extended Kalman filter, our system simultaneously predicts scene geometry and camera position/orientation from the virtual stereo cameras. Also, this method allows user selection of varying baseline lengths, which provides more flexibility given the trade-off between camera resolution, effective measuring distance, flight altitude, and mapping accuracy. Our method outputs dense point clouds at a constant speed of 25 frames per second and is validated on a variety of real-world datasets with satisfactory results.

The process of identifying and approving a new drug is a time-consuming and expensive procedure. One of the biggest issues to overcome is the risk of hepatotoxicity, which is one of the main reasons for drug withdrawal from the market. While animal models are the gold standard in preclinical drug testing, the translation of results into therapeutic intervention is often ambiguous due to interspecies differences in hepatic metabolism. The discovery of human induced Pluripotent Stem Cells (hiPSCs) and their derivatives has opened new possibilities for drug testing. We used mesenchymal stem cells and hepatocytes both derived from hiPSC, together with endothelial cells, to miniaturize the process of generating hepatic organoids. These organoids were then cultivated in vitro using both static and dynamic cultures. Additionally, we tested spheroids composed solely by induced hepatocytes. By miniaturizing the system, we demonstrated the possibility of maintaining the organoids, but not the spheroids, in culture for up to 15 days. This timeframe may be sufficient to carry out a hypothetical pharmacological test or screening. In conclusion, we propose that the hiPSC-derived liver organoids model could complement or, in the near future, replace the pharmacological and toxicological tests conducted on animals.

High efficiency and safety are critical factors in ensuring optimal performance and reliability of systems and equipment across various industries. Fault Monitoring (FM) techniques play a pivotal role in this regard by continuously monitoring system performance and identifying the presence of faults or abnormalities. However, traditional FM methods face limitations in fully capturing the complex interactions within a system and providing real-time monitoring capabilities. To overcome these challenges, Digital Twin (DT) technology has emerged as a promising solution to enhance existing FM practices. By creating a virtual replica or digital copy of a physical equipment or system, DT offers the potential to revolutionize fault monitoring approaches. This paper aims to explore and discuss the diverse range of predictive methods utilized in DT and their implementations in FM across industries. Furthermore, it will showcase successful implementations of DT in FM across a wide array of industries, including manufacturing, energy, transportation, and healthcare The utilization of DT in FM enables a comprehensive understanding of system behavior and performance by leveraging real-time data, advanced analytics, and machine learning algorithms. By integrating physical and virtual components, DT facilitates the monitoring and prediction of faults, providing valuable insights into the system’s health and enabling proactive maintenance and decision-making.

Recently, 3D printing techniques gained much attention in solid dosage form production. Even though the methods are increasingly studied, there are still many challenges in establishing an accurate content of active ingredients in the final products. In the present study, new experimental design techniques and statistical software were developed to identify and optimize a formula to predict the mass of the tablet to be 3D printed before it actually is. The first step was to develop a virtual 3D object in the FreeCad Software, then, using a CURA slicer software, the G-code Format was obtained. The tablets were printed using a Cartesian 3D printer based on the generated data. Finally, adapting the object sequencing mode, a predicted drug mass value was obtained. As expected, the oblong tablet's scaling directly influences its mass. The software generates a correlation coefficient (r) of 0.84, confirming the directly proportional relationship between scaling and tablet weight. However, the r values progressively decreased, indicating a poor correlation between tablet weight and other factors: infill density percent (r = 0.403) and wall thickness (r = 0.185). After repeating the 3D printing with the values ​​suggested by the software, tablets with a practical value of 1066 mg were obtained. Considering that the confidence interval calculated is [834.95—1165.05] and the experimental value is 1066 mg, it can be certified that the proposed model is valid.

Magnesium ions play an important immune-regulatory role during bone repair. For this study, we prepared micro-nano bioactive glass containing magnesium, which can release magnesium, silicon, and calcium ions and has a positive impact on osteogenic differentiation and vascular regeneration. In this study, MgMNBG was compounded and combined with PLGA and PCL for 3D printing. Afterwards, the physicochemical properties and bone repair performance of the scaffolds were evaluated through in vitro and in vivo experiments. We also investigated the effects of MgMNBG on osteogenic differentiation, immune regulation, and vascular regeneration. The results showed that MgMNBG can inhibit inflammation and promote osteogenesis and angiogenesis by regulating macrophages. PLGA/PCL/MgMNBG scaffolds have good osteogenic and angiogenic effects, and the composite scaffolds have excellent bone repair performance and potential application value.

The addition of biocarriers can improve the biological processes appearing in a bioreactor since their surface allows the immobilization, attachment, protection, and growth of microorganisms. In addition, the development of a biofilm layer allows the colonization of microorganisms in the biocarriers. The structure, composition, and roughness of the biocarriers' surface are crucial factors that affect the development of the biofilm. In the current work, the aluminosilicate zeolites 13X and ZSM-5 were examined as the main building components of the biocarrier scaffolds, using bentonite, montmorillonite, and halloysite nanotubes as inorganic binders in various combinations. 3D printing was utilized to form pastes into monoliths that underwent heat treatment. The 3d-printed biocarriers were subjected to a mechanical analysis, including density, compression, and nanoindentation tests. Furthermore, the 3d-printed biocarriers were morphologically and structurally characterized using nitrogen adsorption at 77 K (LN2), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The stress-strain response of the materials being studied was obtained through nanoindentation tests combined with finite element analysis (FEA). These tests were also utilized to simulate the lattice geometries under compression loading conditions to investigate their deformation and stress distribution in relation to experimental compression testing. The results indicated that the 3d-printed biocarrier 13X/halloysite nanotubes was endowed with high specific surface area and extended mesoporous structure. Due to these assets, its bulk density was one of the lowest observed amongst the biocarriers derived from the various combinations of materials. The biocarriers based on the 13X zeolite exhibited the highest mechanical stability and appropriate morphological features. The 13X/halloysite nanotubes scaffold exhibits a moderate hardness value compared to the rest, while it presents the highest value of modulus of elasticity. In conclusion, Aluminosilicate zeolites and their combination with clays and inorganic nanotubes afford 3d-printed biocarriers of various textural and structural properties, which can be utilized to improve biological processes.

The unsolved problem in three-dimensional surgical planning for patients with facial deformity, dysgnathia, or asymmetry is the lack of a normative database of “norm skulls” that can be used as treatment objectives. A study was conducted on 90 Eurasian persons (46 male and 44 female adults) with normal and balanced facial appearance, skeletal Class I pattern, and proper interincisal relationship with normal occlusion. Cone-beam computed tomography was performed. 18 landmarks were digitized and 3D cephalometric measurements of overall facial features, skull, midface and mandible were performed and analyzed by means of proportions calculated from the landmarks. Male and female skulls were analyzed as well as subdivisions revealed by cluster analysis. The data showed that four subtypes of skulls were distinguishable with statistical significance (p< 0,05). A male and a female type subdivided in a brachiocephalic and dolichocephalic phenotype could be identified. For each type then a mean shape was calculated by a Procrustes transformation, which in turn was used to create four template skulls from a male and a female skull by means of a thin plate spline transformation. The normative data of the subtypes can individually serve as a guide for orthodontic surgery, especially helpful in 3D plan-ning and execution of craniofacial operations.

UAV has become powerful devices for both practitioners and researchers. In recent years, there has been a substantial growth in the usage of UAV for a wide range of applications in research and engineering. UAV are mostly utilized for image capturing techniques due to their time savings, low cost, minimum field work, and high precision. The purpose of this study is to generate an accurate and reliable 3D modelling process using UAVs photogrammetric technology; hence this study allows the techniques to evaluate the practicability of modelling and mapping inaccessible tunnels using images recorded by UAVs and photogrammetry. As a result, the approach was always employed to depict the true state of the place. This research incorporates three experiments. The first experiment is to build a 3D model using only one-directional light source and evaluate the accuracy of 3D photogrammetric model and conducted at the concrete tunnel. The second one is to build a 3D model of underground sewer tunnel using different light sources one-directional and omni-directional. The last experiment was to build 3D model using an UAV system which is developed based on first and second experiment’s result, evaluate an accuracy of 3D photogrammetric model and conducted at the tunnel named in the research as a “pedestrian tunnel. There is certain limitation in this study such as Adding a payload to a drone changed its weight distribution, which affected its stability. If the payload was not properly balanced, it caused the drone to fly unevenly, making it more difficult to control.

Regeneration of biological tissues in medicine is challenging, and 3D bioprinting offers an innovative way to create functional multicellular tissues. One common way in bioprinting is bioink which is one type of the cell-loaded hydrogel. For clinical application, however, the bioprinting still suffers from satisfactory performance, e.g. in vascularization, effective antibacterial, immunomodulation and regulation of collagen deposition. Many studies have incorporated different bioactive materials into the 3D printed scaffolds to optimize the bioprinting. Here, we review a variety of additives added to the 3D bioprinting hydrogel. The underlying mechanisms and methodology for biological regeneration are important and will provide useful basis for future research.

The repurposing of licenced drugs for use against COVID-19 is one of the most rapid ways to develop new and alternative therapeutic options to manage the ongoing pandemic. Given the approximately 8,000 licenced compounds available from Compounds Australia that can be screened, this paper demonstrates the utility of commercially-available ex vivo/3D airway and alveolar tissue models. These models are a closer representation of in vivo studies compared to in vitro models, but retain the benefits of rapid in vitro screening for drug efficacy. We demonstrate that several existing drugs appear to show anti-SARS-CoV-2 activity against both Delta and Omicron Variants of Concern in the airway model. In particular, fluvoxamine, as well as aprepitant, everolimus, and sirolimus have virus reduction efficacy comparable to the current standard of care (remdesivir, molnupiravir, nirmatrelvir). Whilst these results are encouraging, further testing and efficacy studies are required before clinical use can be considered.

The soft robot has many degrees of freedom, strong environmental adaptability and good human-computer interaction ability. As the end-effector of the soft robot, the soft gripper can grasp objects of different shapes without destructivity. Based on the theoretical analysis of the soft robot, the kinematics model of the flexible gripper and the theoretical model of the bending deformation of the air cavity were established. Accordingly, the relationship between the bending angle of the soft gripper and the air pressure was determined. Through the application of finite element software, the bending degree of pneumatic network multi-cavity soft gripper was simulated by finite element software, and the influence of structural parameters of soft actuator on bending deformation was determined. In addition, with the 3D technology conducting the printing of soft gripper fixtures and molds, the injection molding the actuator and the human-computer interaction interface controlling the movement of the gripper, the adaptability of the soft gripper in grasping object was verified. The result shows that the software gripper possesses good flexibility and can better grasp objects of different shapes.

3D city models integrate heterogeneous urban data from multiple sources in a unified geospatial representation, combining both semantics and geometry. Although in the last decades, they are predominantly used for visualization, today they are used in a large range of tasks related to exploration, analysis, and management across multiple domains. The complexity of urban processes and the diversity of urban environment bring challenges to the implementation of 3D city models. To address such challenges, this paper presents the development process of a 3D city model of a single neighborhood in Sofia city based on CityGML 2.0 standard. The model represents the buildings in LOD1 with a focus on CityGML features of related to the buildings like building part, terrain intersection curve and address. Similar building models of 18 cities provided as open datasets are explored and compared in order to extract good modeling practices. As a result, workflows for generation of 3D building models in LOD1 are elaborated and improvements in the feature modeling are proposed. Two options of building model are examined: modeling of a building as a single solid and modeling of a building with separate building parts. Finally, the possibilities for visualization of the model in popular platforms such as ArcGIS Pro and Cesium Ion are explored.

There is need to address the challenges of organ shortage, through development of tissues and organs with alternatives to those of the allograft-kind. This illustrates the quest behind novel biofabrication strategies such as 3D bio-printing, which is necessary to create artificial multi-cellular tissues/organs. Several findings have been reported in this review. First, the role of ECM components in tissue regenerative medicine is presented. Different ECM components such as collagen, gelatin, elastin, fibronectin, laminins and glycosaminoglycans are concisely examined for their tissue regenerative medicine applications. Next, current state of research on extrusion-based 3D bio-printing techniques and their limitations are reviewed. For example, we show that cell viability is still a challenge with extrusion, while the use of natural polymers such as collagen in improving composites’ mechanical properties is limited. Lastly, we examine unresolved research questions necessary to advance the present state of research in the field.

Cancer cachexia is a multifactorial syndrome that is identified by ongoing muscle atrophy, along with functional impairment, anorexia, weakness, fatigue, anemia, reduced tolerance to antitumor treatments. Thus, reducing the patients’ quality of life. Cachexia alone causes about 22-25% of cancer deaths. This review covers the symptoms, mediators, available treatment, and prospects of 3D bioprinting for cancer cachexia. Studies about cachexia have shown several factors that drive this disease – protein breakdown, inflammatory cytokines activation, and mitochondrial alteration. Even with proper nutrition, physical exercises, anti-inflammatory agents, chemotherapy, and grafting attempts, standard treatment has been unsuccessful for cachexia. But the use of 3D bioprinting shows much promise compared to conventional methods by attempting to fabricate 3D constructs mimicking the native muscle tissues. In this review, some 3D bioprinting techniques with their advantages and drawbacks, along with their achievements and challenges in in-vivo applications have been discussed. Constructs with neural integration or muscle-tendon units aim to repair muscle atrophy. But it is still difficult to properly bio-print these complex muscles. Although progress can be made by developing new bio-inks or 3D printers to fabricate high-resolution constructs. Using secondary data, this review study shows prospects of why 3D bioprinting can be a good alternate approach to fight cachexia.

Pollen analysis as a part of palynology deals with the morphological determination of pollen and spores. Different technologies with different resolutions varying from simple light microscopy to highly elaborate electron microscopy are used for the examination, depending on the area of application (e.g. sedimentology, melissopalynology, forensic palynology, etc.). To answer the question of whether laser scanning microscopy (LSM) can replace scanning electron microscopy (SEM) for the determination of pollen species, 168 species were examined using LSM. It was concluded that LSM is both efficient and easy to handle. After preparing the fresh pollen, a 3D laser scan takes 5-10 minutes and unlike using SEM, the pollen does not have to be sputtered or processed. The 3D scans can be measured quickly and easily with the integrated software and there were no observable artifacts. At magnifications up to 8545x, the image quality is comparable to that of a sputtered SEM sample whereas at higher magnifications, the SEM method is superior. Overall, pollen display by LSM is much less time consuming and more cost effective than with the SEM method.

The control of the three-dimensional (3D) polymer network structure is important for permselective materials when specific biomolecules detection is needed. Here we investigate conditions to obtain a tailored hydrogel network that combine both molecular filtering and molecular capture capabilities for biosensing applications. Along this line short oligonucleotide detection in a displacement assay is set within PEGDA hydrogels synthetized by UV radical photopolymerization. To provide insights on the molecular filter capability, diffusion studies of several probes (sulforhodamine G and dextrans) with different hydrodynamic radii were carried out using NMR technique. Moreover, fluorometric analyses of hybridization of DNA oligonucleotides inside PEGDA-hydrogels shed light on the mechanisms of recognition in 3D, highlighting that mesh size and crowding effect greatly impact of hybridization mechanism onto polymer network. Finally, we found the best probe density and diffusion transport conditions to allow the specific oligonucleotide capture and detection inside PEGDA-hydrogels for oligonucleotide detection and the filtering out of higher molecular weight molecules.

Fluorescence-linked immunosorbent assay (FLISA) is a commonly used, quantitative technique for detecting biochemical based on antigen–antibody binding reactions using a well-plate platform. With the developments in the manufacturing technology of microfluidic systems, FLISA can be implemented onto microfluidic disk platforms, which allows the detection of trace biochemical with high resolutions. Apart from requiring a lower proportion of reagent (1/10), this method also reduces the time required for the entire process to less than an hour. The incubation process involves antigen–antibody binding reactions as well as the binding of fluorogenic substrates to target proteins. The protocol for FLISA on a microfluidic platform necessitates the appropriate execution of liquid reagent movements during each step in order to ensure sufficient binding reactions. Herein, we propose a novel microfluidic disk comprising a 3D incubation chamber. Vascular endothelial growth factor as concentration with ng mL-1 is detected sequentially using a benchtop process employing this 3D microfluidic disk. The 3D microfluidic disk is implemented without requiring manual intervention or additional procedures for liquid control. During the incubation process, microbead movement is controlled through centrifugal force, generated due to disk rotation, and gravitational force via bead sedimentation on the sloped floor of the chamber.

Metal 3D printing technology is a promising manufacturing method, especially in the case of complex shapes. The quality of the printed product is still a challenging issue for mechanical applications. The anisotropy of the microstructure, imperfections, and residual stress are some of the issues that diminish the mechanical properties of the printed sample. The simulation could be used to investigate some technical details, and this research has tried to computationally study the metal 3D printing of austenitic stainless steel to address austenite microstructure and local yield strength. Two computational codes were developed in Visual basics 2015 to simulate the local heating/cooling curve and subsequent austenite microstructure. A stochastic computational code was developed to simulate austenite grain morphology based on calculated thermal history. Then Hall-Pitch equation was used to estimate the yield strength of the printed sample. These codes were used to simulate the effect of temperature of the printer’s chamber on microstructure and subsequent yield strength. The austenite grain topology is more columnar at a lower temperature. The percentage of the equiaxed zone will be increased at a higher chamber’s temperature. Almost a fully equiaxed austenite microstructure will be achieved at 800 C chamber’s temperature, but the last printed layer, which is columnar and can be removed by cutting then. The estimated local austenite grain size and the local yield strength in the equiaxed regions are in the range of 15 to 30 μm and 270 to 330 MPa at 800 C temperature of printer’s chamber, respectively.

Solar Insolation is the major contributor of earth’s radiation and energy budget. The insolation reaching the surface is a prime input for eco-physiological processes such as evapotranspiration and photosynthesis. Therefore, it is as critical component to assess bio-energy and bio-fuel resources. It is also a crucial input to crop simulation model for yield forecasting and its further applications in solar energy solutions. Although ground observations are better for accuracy purpose, they have challenges of maintenance, regular calibration and upkeeping etc. This call for the continuous spatio-temporal satellite based observations barring the acceptable accuracy. In case of INSAT3D/3DR, Bhattacharya et al. (2015) have derived the surface insolation product which is being used widely. We propose a method of improvement in this product. It is envisaged that a correction applied with the help of ground truth estimates may enhance the utilization of insolation products derived from INSAT3D/3DR datasets. In the present study, surface insolation product derived from INSAT 3D/3DR data at an interval of 30 minutes each (collectively 15 minutes interval) with 4 km spatial resolution was used for duration from May-2017 to Apr-2019 over Nagpur. Ground truth observations for same duration were carried out with CNR4, which were used to correct the INSAT 3D/3DR surface insolation product using the statistical best-fit method. Corrected INSAT 3D/3DR products are found correlating with the ground values well with differences of approximately < 1 W/m2. Best-fit parameters evolved in the present study uses only 2 years of simultaneous ground and satellite data which can be further improved by multi-year data base. We propose better utilization of INSAT 3D/3DR based surface insolation products in the assessment of solar resource mapping over Nagpur (and possibly other regions, such as Bhandara) with the help of best-fit parameters as assessed in the present study.

Although conventional immunohistochemistry for neurotropic Rabies virus (RABV) usually shows a high preference for neurons, non-neuronal cells are also potential target cells and abortive infection of astrocytes is considered a main trigger of innate immunity in the CNS. While in vitro studies indicated differences between field and less virulent lab-adapted RABVs, a systematic and quantitative comparison of astrocyte tropism in vivo is lacking. Here, a recently developed solvent-based tissue clearing technique was used to measure the RABV cell tropism in infected brains. Immunofluorescence analysis of 1 mm-thick tissue slices enabled 3D segmentation and quantification of infection frequencies of astrocytes and neurons. Comparison of highly virulent street virus clones from fox, dog, and raccoon with three lab strains of intermediate and low virulence revealed remarkable differences in the ability to infect astrocytes in vivo. While all viruses and infection routes led to comparable neuron infection frequencies, striking differences were detected for the infection of astrocytes. Consistent and inoculation route-independent astrocyte infection by field viruses, together with route-dependent or undetectable astrocyte infection by lab-adapted or vaccine viruses strongly suggests a model in which the ability to establish productive astrocyte infection in vivo functionally distinguishes field and attenuated lab RABV strains.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

Buildability, i.e. the ability of a deposited material bulk to retain its dimmensions under increasing load, is an inherent prerequisite for formwork-free digital construction (DC). Since DC processes are relatively new, no standard methods of characterization are available yet. The paper at hand presents practice-oriented buildabilty criteria by taking various process parameters and construction costs into consideration. In doing so, direct links between laboratory buildability tests and target applications are established. A systematic basis for calculating the time interval (TI) to be followed during laboratory testing is proposed for the full-width printing (FWP) and filament printing (FP) processes. The proposed approach is validated by applying it to a high-strength, printable, fine-grained concrete. Comparative analyses of FWP and FP revealed that to test the buildability of a material for FP processes, higher velocities of the printhead should be established for laboratory tests in comparison to those needed for FWP process, providing for equal construction rates.

3D bioprinting holds great promise in the field of regenerative medicine as it can create complex structures in a layer-by-layer manner using cell-laden bioinks, making it possible to imitate native tissues. Current bioinks lack both the high printability and the biocompatibility required in this respect. Hence, the development of bioinks that are capable of both properties is needed. In our previous study, a furfuryl-gelatin based bioink, crosslinkable by visible light, was used for creating mouse mesenchymal stem cell-laden structures with high fidelity. In this study, lattice mesh geometries were printed in a comparative study to test against the properties of a traditional rectangular-sheet. After 3D printing and crosslinking, both structures were analysed for swelling and rheological properties, and their porosity estimated using scanning electron microscopy. Results showed that the lattice structure was relatively more porous but sturdy and exhibited a lower degradation rate compared to the rectangular-sheet. Further, the lattice allowed encapsulation of a greater number of cells, allowing them to proliferate to a greater extent compared to the rectangular-sheet that retained a lesser number of cells initially. All of these results collectively affirmed that the lattice poses as a superior scaffold design for tissue engineering applications.

3D plotting is an additive manufacturing technology enabling biofabrication, thus the integration of cells or biologically sensitive proteins or growth factors into the manufacturing process. However, most (bio-)inks developed for 3D plotting were not shown to be processed into clinical relevant geometries comprising critical overhangs and cavities, which would collapse without a sufficient support material. Herein, we have developed a support hydrogel ink based on methylcellulose (mc), which is able to act as support as long as the co-plotted main structure is not stable. Therefore, 6 w/v %, 8 w/v % and 10 w/v % mc were allowed to swell in water, resulting in viscous inks, which were characterized for their rheological and extrusion properties. The successful usage of 10 w/v % mc as support ink was proven by multichannel plotting of the support together with a plottable calcium phosphate cement (CPC) acting as main structure. CPC scaffolds displaying critical overhangs or a large central cavity could be plotted accurately with the newly developed mc support ink. The dissolution properties of mc allowed complete removal of the gel without residuals, once CPC setting was finished. Finally, we fabricated a scaphoid bone model by computed tomography data acquisition and co-extrusion of CPC and the mc support hydrogel.

A novel and simple method to improve the corrosion resistance of copper by constructing a 3D 1-dodecanethiol self-assembled monolayers (SAMs) in 3.5% NaCl solution is reported in this study. Several drops of 1% H3PO4 solution are thinly and uniformly distributed on copper surface to form a 3D nanostructure constituted by Cu3(PO4)2 nanoflowers. The anticorrosion properties of 1-dodecanethiol SAMs on copper surface and on copper surface treated with H3PO4 solution were evaluated. Results demonstrated that 1-dodecanethiol SAMs on bare copper surface exhibit good protection capacity, whereas a copper surface pretreated with H3PO4 solution can substantially enhance the corrosion resistance of 1-dodecanethiol SAMs.

Malignant cells cultured in three-dimensional (3D) models have been found to be phenotypically and biochemically different from their counterparts cultured conventionally. Since most of these studies employed solid tumor types, how 3D culture affects multiple myeloma (MM) cells is not well understood. Here, we compared MM cells (U266 and RPMI8226) in a 3D culture model with those in conventional culture. While the conventionally cultured cells were present in single cells or small clusters, MM-3D cells grew in large spheroids. We discovered that STAT3 was the pathway that was more activated in 3D in both cell lines. The active form of STAT3 (phospho-STAT3 or pSTAT3), which was absent in MM cells cultured conventionally, became detectable after 1-2 days in 3D culture. This elevated pSTAT3 level was dependent on the 3D environment, since it disappeared after transferring to conventional culture. STAT3 inhibition using a pharmacological agent, Stattic, significantly decreased the cell viability of MM cells and sensitized them to bortezomib in 3D culture. Using an oligonucleotide array, we found that 3D culture significantly increased the expression of several known STAT3 downstream genes implicated in oncogenesis. Since most primary MM tumors are naturally STAT3-active, studies of MM in 3D culture can generate results that are more representative of the disease.

We previously designed and synthesized dehydroxyepoxyquinomicin (DHMEQ) as an inhibitor of NF-κB based on the structure of microbial secondary metabolite epoxyquinomicin C. DHMEQ showed anti-inflammatory and anticancer activity in various in vivo disease models without toxicity. Cell detachment from the primary tumor and subsequent invasion are considered to be early phase of metastasis, while tumor cell attachment to the tissue and secondary tumor formation the late phase. The assay system for late phase was set up with intra-portal-vein injection of pancreatic cancer cells. Administration of DHMEQ was found to inhibit the liver metastasis possibly by decreasing the expression of MMP-9 and IL-8. Also when the pancreatic cancer cells treated with DHMEQ was inoculated into the peritoneal cavity of mice, the metastatic foci formation was inhibited. These results indicate that DHMEQ is likely to inhibit the late phase of metastasis. Meanwhile, we have recently employed three-dimensional (3D) culture of breast cancer cells for the model of early phase metastasis. DHMEQ inhibited the 3D invasion of breast cancer cells without toxicity. In this way, DHMEQ was shown to inhibit the late and early phases of metastasis. Thus, DHMEQ is likely to be useful for the suppression of cancer metastasis.

Inexpensive piezoelectric diaphragms can be used as sensors to facilitate both nozzle height setting and build platform leveling in FFF (Fused Filament Fabrication) 3D printers. Tests simulating nozzle contact are conducted to establish the available output and an output of greater than 8 Volts found at 20 ºC, a value which is readily detectable by simple electronic circuits. Tests are also conducted at a temperature of 80 ºC and, despite a reduction of greater than 80% in output voltage, this is still detectable. The reliability of piezoelectric diaphragms is investigated by mechanically stressing samples over 100,000 cycles at both 20 ºC and 80 ºC and little loss of output over the test duration is found. The development of a nozzle contact sensor using a single piezoelectric diaphragm is described.

The emergence of new methodologies and tools for digitizing objects belonging to the Cultural Heritage (CH) changed the paradigms adopted so far. Traditionally, the process to acquire artifacts required specialized and often costly equipment tailored to specific purposes. However, the development of more generalized, adaptable, and affordable tools led to novel approaches. This manuscript provides a glimpse into the evolving landscape of custom-made tools for digital documentation, both hardware and software, and their transformative impact on the digitization techniques, built to meet requirements of specific case studies, including ancient drawings, manuscripts, paintings, and museum objects. The advent of self-built instruments has revolutionized the way professionals work today, by leveraging a new generation of low-cost, adaptable gears, leading to unprecedented flexibility and efficiency, while facilitating the capture of high-quality digital representations of objects with minimal damage and preserving their integrity. The outcomes of instruments and tools specifically produced for the contexts described in this paper highlight their potential for promoting interdisciplinary collaboration, facilitating scholarly research, enhancing conservation efforts, and fostering cultural exchange. Ultimately, this research contributes to illustrate how custom software, in combination with recent devices such as smartphones and 3D printers, underscores the importance of adopting these innovative approaches to generate an ecosystem of tools and methods able to preserve, document, and promote the richness of our collective past for future generations.

Products made from petroleum-derived plastic materials are linked to many environmental problems such as greenhouse gas emissions and plastic pollution. It is desirable to manufacture products from environmentally friendly materials instead of petroleum-based plastic materials. Products made from biomass-fungi composite materials are biodegradable and can be utilized for packaging, construction, and furniture. In biomass-fungi composite materials, biomass particles (derived from agricultural wastes) serve as the substrate and the fungal hyphae network binds the biomass particles together. There are many reported studies on 3D printing of biomass-fungi composite materials. However, there are no reported studies on biodegradation of 3D printed samples from biomass-fungi composite materials. In this study, two types of biomass materials were used to prepare printable mixture hemp hurd and beechwood sawdust. The fungi strain used was Trametes versicolor. Extrusion based 3D printing was used to print samples. 3D printed samples were left for five days to allow fungi to grow. The samples were then dried in an oven for 4 hours at 120ºC to kill all the fungi in the samples. The samples were buried in the soil using a mesh bag and kept in an environmental chamber at 25℃ with a relative humidity of 48%. The weight of these samples was measured every week over the period of three months. Both types of samples (prepared from beechwood sawdust and hemp hurd, respectively) showed weight change after three months. Furthermore, the samples made from hemp hurd had more weight change than the samples made from beechwood sawdust. The SEM (scanning electron microscope) micrographs and FTIR (Fourier transform infrared) spectroscopy showed evidence of biodegradation of these samples.

Background: In high-risk breast cancer patients with skin infiltration the administration of a uniform dose to superficial tissues is fundamental in order to reduce local skin relapse. A personalized bolus may prevent the potential standard bolus’ inadequate dose distribution due to air gaps between the bolus and the skin. In this pilot study, we introduced in clinical practice the use of a personalized 3D printed bolus filled with ultrasound transmission gel. Methods: Seven patients undergoing radiotherapy after mastectomy were selected. 3D printed bolus dosimetric assessment was performed with MOSFET dosimeters on an anthropomorphic phantom and subsequently on three selected cases with increasing bolus shape irregularity. Acute/late toxicity and local control was assessed. Results: Overall, for the clinical cases the percentage median difference between measured and calculated doses was -2.7% (-7.0%÷4.9%). Median follow-up was 21 months. After two years, one patient showed G2 pain, one patient manifested G1 telangiectasia, one patient showed G1 hyperpigmentation, and two patients had no relevant toxicity. Conclusions: Personalized 3D-printed bolus filled with ultrasound gel may easily reproduce the standard bolus’ consistency providing an accurate coverage of the target area with tolerable acute/late toxicity grades. This is a pilot study and further investigations are needed.