The purpose of this study was to determine changes in the mechanical properties of the thigh and lower leg musculature during the early follicular and ovulatory phases. Subjects were 15 female university students with normal menstrual cycles. The early follicular and ovulatory phases were estimated by the basal body temperature method, ovulation kits, and salivary estradiol concentration measurement. The MyotonPRO digital palpation device (Myoton AS, Tallinn, Estonia) was used to measure muscle and tendon stiffness in the early follicular and ovulatory phases. Measurement sites were the rectus femoris (RF), vastus medialis (VM), patellar tendon (PT), medial head of gastrocnemius, soleus, and Achilles tendon. No significant differences in stiffness of all muscle tendons were identified between the early follicular and ovulatory phases. In the ovulatory phase, a significant positive correlation was seen between stiffness of RF and PT, and between stiffness of VM and PT. These results suggest that the stiffness of muscles and tendons of anterior sites of the thigh and posterior sites of the lower leg may not change between the early follicular and ovulatory phases. During the ovulatory phase, tendons may also be stiffer in individuals with stiffer anterior thigh muscles.

In this study, a 5vol. % (TiBw+TiCp)/Ti composite pancake with a diameter of 260mm was prepared by casting followed by open die forging in (α+β) phase region. The microstructures of the composite pancake are inhomogeneous, in terms of both matrix microstructure and distribution of reinforcements. The matrix microstructures were gradually refined from the periphery to centre of the pancake. The TiBw and TiCp reinforcements tend to be uniformly distributed in the centre region and. It is suggested that the microstructure difference can be mainly ascribed to the temperature variation from the periphery to the centre. Additionally, tensile testing results showed that the centre region of the composite pancake exhibits higher strength than the peripheral region. The strengthening mechanism and the softening behavior of the composite pancake with temperature is discussed.

Ventilation in prone position (PP) for 12 to 16 hours per day improves survival in ARDS. However, the optimal duration of the intervention is unknown. We performed a prospective observational study to compare the efficacy and safety of a prolonged PP protocol with conventional prone ventilation in COVID-19-associated ARDS. Prone position was undertaken if P/F <150 with FiO2>0.6 and PEEP>10cmH2O. Oxygenation parameters and respiratory mechanics were recorded before the first PP cycle, at the end of PP cycle and 4 hours after supination. We included 63 consecutive intubated patients with mean age 63.5 years. Of them, 37 (58.7%) underwent prolonged prone position (PPP group) and 26 (41.3%) standard prone position (SPP group). Median cycle duration for SPP group was 20 hrs and for PPP group 46 hrs (p<0.001). No significant differences in oxygenation, respiratory mechanics, number of PP cycles and rate of complications were observed between groups. The 28-day survival was 78.4% in the PPP group versus 65.4% in the SPP group (p=0.253). Extending the duration of PP was as safe and efficacious as conventional PP, but did not confer any survival benefit in a cohort of patients with severe ARDS due to COVID-19.

Although 7055 aluminum alloy is a deformed aluminum alloy and will show excellent mechanical properties after recrystallization after large deformation, it is a method to enrich its application range if rare earth is added and the rare earth phase dispersion is promoted by heat treatment. This article used optical microscopy, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD), micro Vickers hardness and room temperature stretching methods to study the as-cast 7055-xEr (x=0wt.%, 0.2wt.%, 0.4wt.%, 0.6wt.%, 0.8wt.%) aluminum alloy after being subjected to 460 oC×3h homogenization and 410 oC×1h solid solution+150 oC×12h aging treatment the changes in microstructure and properties. The results indicated that: when 0.2wt.%Er was added to 7055 aluminum alloy after solution at 410 oC×1h and aging at 150 oC×12h, the dendrite structure was significantly reduced, the grain thinning was obvious and the distribution was uniform, Al8Cu4Er phase appeared in the lamellar eutectic η-Mg(Zn,Al,Cu)2 structure at grain boundaries, and the hardness reached 168.8HV. The yield strength, tensile strength and elongation were 542.12Mpa, 577.67MPa and 8.36%, respectively.

Polyethylene terephthalate (PET) is nowadays one of the most used polymers for packaging applications. Modifications induced by service conditions and the optimal mean to recycle this matter several times have to be perfectly understood to allow a reuse for similar application (from bottle to bottle for example). The present study aims to compare physico-chemical properties, crystalline organization, and mechanical behaviour of virgin (vPET) and recycled PET (rPET). Using different combined experimental methods (Calorimetry, Small Angle X-ray Scattering, Atomic Force Microscopy, DMA, and uni-axial tensile test), it has been proven that even if there is no change in the crystallinity of PET, the crystallisation process shows some differences (size and number of spherulites). The potential impact of these differences on local mechanical characterization, at the lamella scale, is explored and tends to demonstrate the development of homogeneous microstructure, leading to well-controlled and relevant local mechanical properties. This approach increases the understanding of crystallisation of PET and recycled PET during forming processes such as thermoforming or injection stretch blow moulding (ISBM) where elongation at break can depend on the microstructure conditioned by the crystallisation process.

Although the dry ice method used to synthesize exfoliated graphite/graphene is little known and used, it has significant advantages over others: it is low cost, simple, and a large quantity of material can be obtained using some inorganic and highly available acids (which can be reused). Despite the above advantages, the main reason for its incipient development is the resulting presence of magnesium oxide in the final product. In the present work, three different treat-ments were tested to remove this remnant using some acid chemical leaching processes, making use of hydrochloric acid, aqua regia, and piranha solution. Based on the experimental evidence, it was found that using aqua regia and combining the leaching process with mechanical milling was the most efficient way of removing such a remnant, the residue being only 0.9 wt.%. This value is low when compared to that obtained with the other acid leaching solutions and purifi-cation process (2.8 - 29.6 wt.%). A mandatory high-energy mechanical milling stage was neces-sary during this treatment, in order to expose and dissolve the highly insoluble oxide without secondary chemical reactions on the graphenes. High-energy mechanical milling is an effective route to exfoliate graphite/graphene, which allows the magnesium oxide to be more susceptible to acid treatment. The obtained surface area was 504 m2g-1; this high value resulting from the in-tense exfoliation can potentiate the use of this material for a wide variety of applications.

The objective of this study is to conduct a mineralogical and chemical characterization of the mortars Roman archaeological site of Volubilis to rebuild spare mortars for restoration. We take samples of mortar, broken tile palate garden, and pavement mosaic Falavius Germanus houses. The analysis by X-ray diffraction reveals the coarse mortar Flavius Germanus is made of quartz and calcite with feldspar and probably, mica and dolomite in small amounts. The binder end is formed calcite and quartz. However, the broken tile mortar is formed by coarse particles, clay base mixed with a binder phase dominated by calcite. These results allowed us to reformulate spare mortars for the restoration of damaged Roman mosaics. The mortars are made up by 63.6% of lime and 36.4% of sand(with 4.19% of large grain, 71, 04% of coarse sand, 24.22%, of fine sand and 0.55% fines parts).The performance of these mortars was tested by mechanical testing.

The SARS-Cov-2 virus, which causes COVID 19, uses the cell surface protein ACE2 as receptor for entry into cells. Critically ill COVID-19 patients often require prolonged mechanical ventilation which can cause mechanical stress to lung tissue. In vitro studies have shown that expression of ACE2 in alveolar cells is increased following mechanical stretch and inflammation. Therefore, we analyzed transcriptome datasets of 480 (non-COVID-19) lung tissues in the GTex tissue gene expression database. We found that mechanical ventilation of the tissue donors increased the expression of ACE2 by more than two-fold (p<10^-6). Analyses of transcriptomes of mechanically ventilated mice in the GEO database indicate that this alveolar cell response to stretch and inflammation is mediated by the chemokine midkine. Using a novel big knowledge network approach (SPOKE) we also found in transcriptomes of pharmacological perturbations (LINCS) that corticosteroids down-regulate midkine in pulmonal cells, and confirmed this in GEO transcriptomes of animal studies. Thus, mechanical ventilation of patients with COVID-19 pneumonia may eo ipso facilitate viral propagation in the lung, further accelerating the pulmonal pathology that has necessitated mechanical ventilation in the first place. This vicious cycle presents a rationale for the temporary treatment with corticosteroids to modulate the midkine-ACE2 axis in ventilated COVID19 patients and for gentler ventilation protocols.

The mechanical properties of the materials stored inside agricultural silos influence the loads generated inside them. The different silo calculation methodologies allow predicting these loads under static and dynamic conditions if the mechanical properties of the stored materials are known. It has been known for many years that these properties are highly dependent on the moisture content of the material. However, to date there are not many studies focused on its determination. The goal of this research is the determination of the angle of internal friction, apparent cohesion, dilatancy angle and apparent specific weight of maize subjected to different moisture contents. Direct shear and oedometer assay devices were used for this purpose. In addition, the maize samples used were moistened using a climatic chamber. Moisture contents applied to maize sample ranged from 9.3% to 17.4%. The results obtained for the angle of internal friction and apparent cohesion, as well as those obtained for the apparent specific weight, were similar to those reported in the literature. However, the values obtained for the dilatancy angle of maize as a function of moisture content could not be compared because nothing has been published so far. The values obtained for this parameter overlap with those published for this material under ambient conditions. In addition, no direct relationship between the values obtained for this parameter and the moisture content of the sample could be found. Finally, the apparent specific weight increased with increasing moisture content of the samples, which differed from that published in the literature. The values provided here can be used for the optimization of storage and handling structures for granular agricultural materials using numerical methods.

The preparation of new materials based on starch for the development of biodegradable packaging is increasing, however, the poor properties of this biopolymer for this application causes an area of opportunities for the improvement of water vapour permeability (WVP), mechanical properties, thermal properties, hydrophilicity, water absorption, among others. Hence, starch has been combined with other polymers such as polyvinyl alcohol, which has shown an improvement in the mechanical properties of starch, also, the use of clays suggests that the properties of response to water can be improved. Therefore, in this work, the preparation and characterization of starch-PVA-nanoclay films prepared by solvent casting is reported. The results obtained suggest that the sonication of nanoclay is necessary to reach a good dispersion, which promotes a strong interaction among starch-PVA-nanoclay. In addition, the properties of WVP and mechanical properties of films improved with incorporation of nanoclay, the concentration of 0.5% w/v of nanoclay showed to be the best concentration due to concentrations of 1.0 and 1.5% w/v were poorer than 0.5% w/v. Accordingly, the successful incorporation of nanoclays into the matrix starch-PVA suggests that this material is a good candidate for use as packaging.

Hydrogel-based wearable electrochemical biosensors (HWEBs) are emerging biomedical devices that have recently received immense interest. The exceptional properties of HWEBs include excellent biocompatibility with hydrophilic nature, high porosity, tailorable permeability, the capability of reliable and accurate detection of disease biomarkers, suitable device-human interface, facile adjustability, and stimuli-responsive to the nanofiller materials. Although the biomimetic three-dimensional hydrogels can immobilize bioreceptors, such as enzymes and aptamers, without any loss in their activities. However, most HWEBs suffer from low mechanical strength and electrical conductivity. Many studies have been performed on emerging electroactive nanofillers, including biomacromolecules, carbon-based materials, and inorganic and organic nanomaterials, to tackle these issues. Non-conductive hydrogels and even conductive hydrogels may be modified by nanofillers as well as redox species. All these modifications have led to the design and development of efficient nanocomposites as electrochemical biosensors. In this review, both conductive-based and non-conductive-based hydrogels derived from natural and synthetic polymers are systematically reviewed. The main synthesis methods and characterization techniques are addressed. The mechanical properties and electrochemical behavior of HWEBs are discussed in detail. Finally, the prospects and potential applications of HWEBs in biosensing, healthcare monitoring, and clinical diagnostics are highlighted.

The aim of the present study was to describe and determine changes in the superelastic properties of NiTi archwires after clinical use and sterilization. Ten archwires from five different manufacturers (GAC, 3M, ODS, GC, FOR) were cut in two segments and evaluated using a three-point bending test in accordance with ISO 14841:2006. The centre of each segment was deflected to 3.1mm and then unloaded to 0 N to obtain a load-deflection curve. Deflection at the end of the plateau and forces at 3, 2, 1 and 0.5mm on the unloading curve were recorded. Plateau slopes were calculated at 2, 1 and 0.5mm of deflection. Data obtained were statistically analysed to determine differences (p&lt;0.001). Results showed that the degree of superelasticity and exerted forces differed significantly among brand groups. After three months of clinical use, FOR released a greater force for a longer activation period. GC, EURO and FOR archwires seemed to lose their mechanical properties. GC wires released more force than other brand wires after clinical use. Regarding superelasticity after sterilization, GAC, 3M and FOR wires recovered their properties, while EURO archwires lost more.

Polyacrylamide gel electrophoresis (PAGE) is widely used for studying proteins and protein-containing objects. However, it is employed most frequently as a qualitative method rather than a quantitative one. In this paper, we show the feasibility of routine digital image acquisition and mathematical processing of electrophoregrams for protein quantification. Both the well-studied model protein molecules (bovine serum albumin) and more complex real-world protein-based products (casein-containing isolate for sports nutrition), which were subjected to mechanical activation in a planetary ball mill to obtain samples characterized by different protein denaturation degrees, were used as study objects. Protein quantification in the mechanically activated samples was carried out. The degree of destruction of individual protein was shown to be higher compared to that of protein-containing mixture after mechanical treatment for an identical amount of time. The methodological approach used in this study can serve as guidance for other researchers who would like to use electrophoresis for protein quantification both in individual form and in protein mixtures. The findings prove that photographic imaging of gels followed by mathematical data processing can be applied for analyzing the electrophoretic data.

Mechanical response of bisphenol-F based epoxy cured with amine hardener was investigated in tensile testing. Different types of methods were considered in preparing the tensile samples in order to evaluate their effects on the tensile strength of the cured epoxy system. Specifically, four types of preparation methods were discussed to prepare the tensile samples were considered in the study. Further, the effect of different type of tensile samples on tensile strength of specimens was also considered in the analysis. The experimental results showed that the preparation methods affected the tensile strength of the specimens. Starting from the experimental results, an appropriate testing methodology is proposed for epoxy based nanocomposite composite specimens in order to reduce problems that may arise during the test and to optimize procedures for preparation of specimens.

(1) Background: Mechanical circulatory support (MCS) in myocardial infarction associated cardiogenic shock is subject to debate. This analysis aims to elucidate the impact of MCS timing on patient outcomes, based on data from the PREPARE CS registry.; (2) Methods: PREPARE CS prospective registry included consecutive patients experiencing cardiogenic shock (SCAI Classes C-E) and were referred for cardiac catheterization. Present analysis included a subset, in whom MCS was used and underwent coronary intervention due to myocardial infarction. Patients were categorized into Upfront group versus Procedural group, depending on the timing of MCS introduction in relation to PCI. Endpoint was the in-hospital mortality; (3) Results: In total 71 patients were included. MCS was started prior to PCI in 33 (46%) patients (Upfront), whereas 38 (54%) received MCS during or after PCI initiation (Procedural). Baseline characteristics and hemodynamic parameters were comparable. The Upfront group had a higher utilization of Impella® device compared to extracorporeal membrane oxygenation (67% vs 33%), while the Procedural group exhibited a balanced use (50% vs 50%). Most patients suffered of multi-vessel disease in both groups (82% vs 84%, respectively; p=0.99) and most patients required complex PCI procedure, the latter was more prevalent in the Upfront group (94% vs 71%, respectively; p=0.02). Rates of complete revascularization were comparable (52% vs 34%, respectively; p=0.16). Procedural CPR was significantly more frequent in the Procedural group (45% vs 79%, p&lt;0.05), still in-hospital mortality was similar (61% vs 79%, respectively; p=0.12); (4) Conclusions: Upfront implantation of MCS in myocardial infarction associated CS did not provide in-hospital survival benefit.

Composites, and especially carbon fiber reinforced plastics (CFRPs), are increasingly used in the automotive, aerospace, and aviation industries, and as a result, CFRP production has increased dramatically, leading to a corresponding increase of waste. Landfill and incineration of waste are likely to be restricted as a result of the legislation, thus highlighting the need for efficient recycling methods for CFRPs. However, the recycling of CFRP is very challenging, mainly due to the difficulty of removing the thermosetting matrix. This study reports a pre-screening of the solvolysis recycling process for CFRPs based on the mechanical properties of the recovered fibers. To this end, solvolysis tests were conducted on unidirectional CFRP samples under supercritical and subcritical conditions using acetone and water. The solvolysis tests were conducted for various conditions of temperature, pressure, and reaction time. The efficiency of the recycling processes has been evaluated through a morphological and a mechanical characterization of the recovered fibers. In most cases, the decomposition efficiency of the epoxy resin, measured in terms of mass, ranged between 90 and 100%. Moreover, the scanning electron microscopy images of the recovered fibers showed negligible traces of resin residues and no detectable signs of physical damage or any changes in morphology with regard to diameter. Finally, the single-fiber tension tests revealed that that the recovered fibers retained more than 61% of their initial Young's modulus and 70% of their tensile strength.

Steel slag and GBFS are wastes generated during the steel and iron smelting process, characterized by their considerable production rates and extensive storage capacities. After grinding, they are often used as supplementary cementitious materials. However, the intrinsic slow hydration kinetics of steel slag-GBFS cementitious material (SGM) when exposed to a pure water environment result in prolonged setting times and diminished early-age strength development. The incorporation of modifiers such as gypsum, clinker, or alkaline activators can effectively improve the various properties of SGM. This comprehensive review delves into existing research on the utilization of SGM, examining their hydration mechanisms, workability, setting time, mechanical strengths, durability, and shrinkage. Critical parameters including the performance of base materials (water-to-cement ratio, fineness, and composition) and modifiers (type, alkali content, and dosage) are scrutinized to understand their influence on the final properties of the cementitious materials. The improvement mechanisms of various modifiers on properties are discussed. This the promotes resource utilization of industrial solid wastes and provides theoretical and technical support for the application of SGM.

The topic of modification of magnesium oxychloride cement (MOC) via specific functional additives is very much pronounced in the research of alternative building materials. This study deals with the co-doping of MOC by 1D and 2D carbon nanomaterials in order to improve its mechanical properties while using tannic acid (TA) as a surfactant. Furthermore, the effect of TA on MOC also covers the improvement of water resistance. As a filler, three size fractions of standard quartz sand are used. The proposed types of MOC-based composites show promising results considering their mechanical, macro- and microstructural, chemical, and hygric properties. The use of 1D and 2D nanoadditives and their mixture enables the improvement of the flexural strength and most of all softening coefficient, the durability parameter characterizing the resistance of the prepared materials to water. For samples immersed in water for 24 h, the compressive strength of all modified composites tested was higher than that of the reference composite. Quantitatively, the developed co-doped composite shows mechanical parameters comparable to or even better than those of commonly used Portland cement-based materials, while maintaining high environmental efficiency. This indicates its potential use as an environmentally friendly alternative to Portland cement-based products.

With the advancement of Additive Manufacturing and its applications in various industrial segments, it becomes increasingly important to investigate the processability parameters associated with nano-reinforcement. This study examines the influence of infill parameters, such as patterns (hexagonal, triangular and concentric), shape (solid and honeycomb) and concentrations by mass of Carbon Nanotubes (CNTs) at 1.0 wt% and 2.0 wt% on the mechanical compression properties of the 3D printed material. In this sense, nanocomposites based on Polylactic Acid (PLA) matrix nano-reinforced by CNTs were characterized using the Scanning Electron Microscopy -SEM, X-ray Diffraction, Raman Spectroscopy techniques and mechanical analysis. The mechanical properties of both the matrix and the nanocomposites were determined through mechanical compression tests, in accordance with [1]. SEM revealed compacted regions, voids, and detachment in the structures. XRD characterization indicated PLA predominantly amorphous nature, while CNTs exhibited characteristic diffractions of carbon nanotubes. Raman characterization showcased bands and characteristic vibrations of CNTs and PLA, nanocomposites' vibrational modes combine those of CNTs and PLA. Mechanical compression analysis indicates a direct influence of infill pattern, shape, and nano-reinforcement. The triangle pattern outperformed other patterns, exhibiting a 15.03% increase compared to concentric and 8.8% compared to hexagon infill. In nanocomposites, all showed higher compressive strength than the matrix. For PLA/1.0%CNTs, strength was 16.8%, and for PLA/2.0%CNTs, it reached 39.2%. In honeycomb shapes with infill variations, the triangular pattern excelled with a 0.97% increase over concentric and 6.12% over hexagon patterns. Honeycomb results indicate a 59.6% increase for (PLA/1.0%CNTs) and a 0.48% increase for (PLA/2.0%CNTs) compared to the matrix. This study highlights 3D printing parameters, emphasizing the effectiveness of the triangular pattern and the enhanced strength with the addition of CNTs, providing insights to enhance products manufactured through Additive Manufacturing.

Polymethyl methacrylate (PMMA) is a transparent thermoplastic with excellent optical properties, transparent surface, low moisture absorption, tensile and electrical resistance. In this study, the alloy was prepared through PMMA and cycloolefin copolymer (COC) due to some similar properties. The mechanical test showed that properties such as impact resistance, elongation, tensile, and flexural strength decreased by adding COC by up to 20% due to less incompatibility and miscibility, but mentioned properties improved by adding COC 40% due to sub-phase generation. The DSC and DMTA tests showed improvement in the thermal properties of alloys by adding 40% COC. SEM micrographs exhibited a softer surface and more phase elongation of the alloy. Finally, the sample was selected as the optimal sample in terms of mechanical properties irradiated by electron beam, and amplification results showed that a dose of 50 KGY increased the mechanical and thermal properties relatively.

Metal 3D printing technology is a promising manufacturing method, especially in the case of complex shapes. The quality of the printed product is still a challenging issue for mechanical applications. The anisotropy of the microstructure, imperfections, and residual stress are some of the issues that diminish the mechanical properties of the printed sample. The simulation could be used to investigate some technical details, and this research has tried to computationally study the metal 3D printing of austenitic stainless steel to address austenite microstructure and local yield strength. Two computational codes were developed in Visual basics 2015 to simulate the local heating/cooling curve and subsequent austenite microstructure. A stochastic computational code was developed to simulate austenite grain morphology based on calculated thermal history. Then Hall-Pitch equation was used to estimate the yield strength of the printed sample. These codes were used to simulate the effect of temperature of the printer’s chamber on microstructure and subsequent yield strength. The austenite grain topology is more columnar at a lower temperature. The percentage of the equiaxed zone will be increased at a higher chamber’s temperature. Almost a fully equiaxed austenite microstructure will be achieved at 800 C chamber’s temperature, but the last printed layer, which is columnar and can be removed by cutting then. The estimated local austenite grain size and the local yield strength in the equiaxed regions are in the range of 15 to 30 μm and 270 to 330 MPa at 800 C temperature of printer’s chamber, respectively.

For development and successful application of any material, a clear understanding of their mechanical behavior is one of the most important things, but when it comes to nanofibers networks it become a challenge due to, their high porosity, many scales in their structure, and characteristics non-linear. Therefore, an experimental methodology in conjunction with a theoretical model that can fully consider their characteristics is still needed. In this work we proposed a model that incorporates the propagation of the elastic waves in two-phase media to determine the effective elastic modulus of electrospun membranes of PLA/gelatin given the mechanical properties of nanofibers, shape, distribution and concentration. The model was verified via laser ultrasonic testing. It was found that the values predicted for the effective modulus by the model were higher than the values obtained from experimental results. One explanation is due to the experimental density. As a result, the P-Wave velocity from the model best fit to experimental results and it has the same behavior, decrees as the concentration of gelatin in the solution. These results indicate the model and experimental methodology can assist in the dressing of nanofibers networks and electrospun materials.

The aim of this work was to prepare bioplastics from renewable and biodegradable molecules. In particular, the bioplastics were produced by using as biopolymer source the grass pea (Lathyrus sativus L.) flour, the proteins of which were structurally modified by means of microbial transglutaminase, an enzyme able to catalyze isopeptide bonds between glutamines and lysines. We analyzed, by means of Zeta-potential, the flour suspension with the aim to choose which pH is more stable for the production of film-forming solutions. The bioplastics were produced by casting and they were characterized according to several technological properties. Optical analysis demonstrated that films cast in the presence of the microbial enzyme are more transparent compared to the untreated ones. Moreover, the visualization by Scanning Electron Microscopy demonstrated that the enzyme-modified films possessed a more compact and homogeneous structure. Furthermore, the presence of microbial transglutaminase allowed to obtain film more mechanically resistant. Finally, digestion experiments under physiological conditions performed in order to obtain information useful for applying these novel biomaterials as carriers in the industrial field, indicated that the enzyme-treated coatings might allow the delivery of bioactive molecules in the gastro-intestinal tract.

The hot rolling in the process chain of the aluminium rolled products present the critical element of material quality and influence on productivity. The desire to increase the letter demand modifications of hot rolling, consequential changes of microstructure, crystallographic texture, mechanical and formability properties must be knowledge and consistently considered in planning the rolling process and rolled product. Achieving lower thicknesses of the hot-rolled band would enable fewer passes with cold rolling; consequently, hot rolling with the same number of passes will complete with lower temperatures. Microstructural and texture characterization with the optical microscope and scanning electron microscope for the hot-rolled band 3.25 mm the smaller grains appeared in the center of the cross-section, unlike for the hot-rolled band 6 mm, the smaller grains were detected on the upper and bottom position of the cross-section. Furthermore, the comparison shows also that the hot-rolled band 6 mm has 64 % of random texture components and 83 % of recrystallized grains, and the proportional adjustment for the hot-rolled band 3.25 mm has the 42 % of random texture components and 55 % of recrystallized grains. For the mechanical testing results, the elongation values in rolling and transverse directions significantly differ just in the case of a hot rolled band of 3.25 mm. Consequently, the earing results are more than 1.5 % higher for the hot-rolled band, 3.25 mm, than the hot-rolled band, 6 mm.

Due to the manufacturing process of Additive Manufacturing (AM) Parts the mechanical properties cannot be predicted. The scope of the present work is to propose a predictive tool for the mechanical properties of AM parts through the use of Adaptive Neuro-Fuzzy Inference System (ANFIS). The Adaptive Neuro-Fuzzy Inference System (ANFIS) combines neural networks with fuzzy logic to generate a mapping between the inputs and the output. Real data experiments from different AM technologies and materials compose the initial dataset so a detailed investigation is conducted to gain knowledge of how different parameters affect the UTS, the elongation and the Young modulus of each experiment. Experimental data were also use to train, check and verify the methodology. The method is tested for FFF technology, PLA material and 3 point bending stress, with interesting results.

The developed microstructure features a long with mechanical properties in vacuum brazing of commercially pure Ti-alloy using Ti₂₀Zr₂₀Cu_60-x-Ni_x (x=10, 20, 30, 40 and 50) metallic filler. Brazing temperatures and holding times employed in this study were 1240-1279 K (967-1006^oC) for a period of 10 min, respectively. The mechanical properties of brazed joints were evaluated by nanoindention at a constant peak load of 5000 μN and tensile tests. The number of intermetallic phase, such as NiTi₂, Ti₂Cu, (Ti, Zr)₂Cu, (Ti, Zr)₂Ni, β(Ti, Zr), α-Ti and NiTi. The solid solution matrix have been identified at 1279 K out of these different regions the NiTi₂ rich region had the highest nanohardness of 17 GPa, It is interesting to note that among five different glasses, the Ti₂₀Zr₂₀Cu₁₀Ni₅₀ has the highest yield strength of 17 GPa, which is mainly due to NiTi₂ phase. Based on the tensile test results all cracks propagate along the brittle intermetallic compounds like NiTi₂ in the reaction layer the reduction of the strength of the joints and fracture behaviour upon propagation of the crack, which shows the morphological cleavage including facets characteristics.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

The Wolfram (W), Silicium (Si) and Molybdenum (Mo) doped Co-Cr biomedical alloy were fabricated by additive manufacturing method, which is part of powder metadology. The mixture of Wolfram (W), Silicium (Si), Chrome (Cr) and Cobalt (Co) alloy is known good wear and corrosion resistance among of biomedical applications. By addition of Molybdenum (Mo) into the structure of alloy, the structure become more stbale also increase the corrosion and wear resistance. In addition, the effects of secondary annealing process on the alloy were investigated. The microstructure of the produced alloy was analyzed by X-ray diffraction method XRD, Energy Dispersive X-Ray Analysis EDX and scanning electron microscope SEM. Moreover, Electrochemical corrosion test, micro hardness and density measurements were performed to investigate the mechanical properties of the alloy. As a result of the analyzes, the effects of Molydenum (Mo) doped and secondary annealing on the microstructure and mechanical properties of bioalloying were determined.

The strictness of the result of an excavation, whether mechanical or by means of explosives, is naturally conditioned by the objective, and therefore by the type of technique applied to achieve it. To attain the best results in terms of rock breakage and respect of the final profile, it’s important to evaluate the excavation specific energy and its optimization. This research focuses on evaluating the effects of different techniques on the quality of final walls in open-pit and underground operations. Different geometries and configurations can be applied to both quarrying and tunnelling blasts. The research is aimed to push contour blasts to their limits, and the main aspects are discussed in order to improve the blast parameters in the daily practice.

The construction industry generates significant CO2 emissions, and rebar is a major contributor to this environmental impact. Extensive research has been conducted to address this issue. Recent advancements have introduced algorithms to reduce rebar waste and consumption, demonstrating the feasibility of achieving near-zero rebar cutting waste (N0RCW) by considering special-length rebars. However, conventional lap splices, the most common rebar joint method, consistently consume excessive rebar quantities despite extending beyond their mandated zones. Conversely, couplers eliminate rebar lengths required for lapping splices, reducing the usage of rebar. Applying special lengths and couplers in heavily loaded structures like diaphragm walls can significantly reduce rebar usage and cutting waste, consequently reducing CO2 emissions and associated costs. This study aims to optimize rebar consumption and sustainability in diaphragm wall structures by integrating mechanical couplers with a special-length rebar approach. A case study confirmed a substantial reduction in purchased rebar usage (17.95% and 5.38%) and carbon emissions (15.24% and 2.25%) compared to the original design and previous study, respectively. Broadly implementing the proposed method across various buildings and infrastructure projects could further multiply these benefits, fostering the achievement of SDGs adopted by the United Nations for sustainable construction.

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

This paper mainly used database technology, machine learning, thermodynamic calculation, experimental verification, etc., on integrated computational materials engineering. The interaction between different alloying elements and the strengthening effect of precipitated phases are investigated mainly for martensitic ageing steels. Modelling and parameter optimization were performed by machine learning, and the highest prediction accuracy was 98.58%. Investigated the influence of composition fluctuation on performance and correlation tests to analyze the influence of elements from multiple perspectives. Furthermore, screen out the three-component composition process parameters with composition and performance with high contrast. Thermodynamic calculations studied the effect of alloying element content on the nano-precipitation phase, Laves phase, and austenite in the material. The heat treatment process parameters of the new steel grade were also developed based on the phase diagram. A new type of martensitic ageing steel was prepared by selected vacuum arc melting. The sample with the highest overall mechanical properties had a yield strength of 1887 MPa, a tensile strength of 1907 MPa, and a hardness of 58 HRC. The sample with the highest plasticity had an elongation of 7.8%. The machine learning process for the accelerated design of new ultra-high tensile steels was found to be generalizable and reliable.

Growing concerns about the greenhouse effect, global warming, and adverse climate changes primarily stemming from carbon dioxide (CO2) emissions in traditional Portland cement (OPC) used in civil engineering construction, have prompted a shift toward eco-friendly alternatives like geopolymer cement (GPC). Over the last few decades, significant advancements have been made in developing environmentally sustainable pavement construction materials such as GPC to mitigate global CO2 emissions. The success of geopolymer cement (GPC) as an eco-friendly alternative to OPC has garnered attention for its potential to lower carbon emissions and enhance durability. This is attributed to the sustainable production method of GPC, where industrial cementitious waste materials (such as fly ash (FA), metakaolin (MK), mine tailings (MT), slag, etc.) are combined with an eco-friendly alkaline activator and water through the geopolymerization process. Numerous studies on geopolymer concrete indicate that, like OPC, GPC exhibits comparable mechanical properties, including strength, fire resistance, chemical resistance, and durability. This review explores the properties and applications of GPC as a sustainable material in pavement construction, exploring key studies and advancements in geopolymer technology, particularly its suitability for pavement applications. The assessment covers the mechanical properties, long-term performance, and environmental impact of geopolymer-based pavements, providing a comprehensive overview to inform policymakers, engineers, and researchers about the viability of geopolymer-based materials as a sustainable solution for modern pavement construction.

Abstract: The chemical mechanical polishing (CMP) has been widely used for surface modification of critical materials and components and provided global planarization of topography with a low post-planarization slope high quality and efficiency. The colloidal silica slurries play an important role in the finishing processes of optical components. Monodisperse mesoporous silica nanospheres were synthesized with different surfactant by Stöber method. Their architectural features and texture parameters were characterized by XRD, FTIR, N2 adsorption–desorption isotherms, SEM, XPS, and TGA techniques. The spherical SiO2 products presented with the controllable 50-150 nm particle size and distribution. The AFM micrographs reveal that flat and smooth surfaces without distinct scratches residual particles are achieved by using the as-obtained composite particles as abrasives[The particle size of SiO2 slurry plays a critical role in the chemical-mechanical polishing process.

This study examines the effects of the δ phase and annealing twins on the hardness, Charpy impact toughness, and tensile properties of Inconel 718 fabricated using L-PBF. Two heat treatment methods, involving solid solution and precipitation hardening, were utilized. The δ phase was formed through solid solution heat treatment at 980C for 1 hour while annealing twins were generated at 1100C for 3 hours. After precipitation hardening, specimens with a higher concentration of  precipitates exhibited increased ultimate tensile strength (13%), yield strength (27%), and hardness (12%) compared to those with annealing twins. This can be attributed to the smaller grain size, subgrains, and δ precipitates, which contribute to the differences in mechanical strength. On the contrary, specimens with annealing twins showed significantly higher impact toughness (4 times) and ductility (twice) than those with δ precipitates. This is caused by the formation of  precipitates, which serve as sites for void formation and crack propagation, leading to a decrease in plasticity due to lattice mismatches with the matrix. Microstructural, compositional, phase, crystallographic, and fractographic analyzes were performed using OM, SEM, TEM and XRD techniques to identify the factors responsible for the variations in the measurements. The results demonstrate that the heat treatment method involving annealing twins significantly improves the ductility of Inconel 718 while maintaining the required mechanical strength.

Abstract: To compare the use of variable mechanical ventilation with conventional mechanical ventilation in porcine model of ARDS. Methods: Animals were divided into two groups (n = 6), conventional ventilation and variable ventilation with bi-oscillatory PEEP. For induction of ARDS, intravenous oleic acid was used until a P/F ratio of 200 to 300 mmHg. The animals were ventilated with pressure control, FiO2 1.0, inspiration-expiration ratio = 1:2, tidal volume 6 ml/kg with the initial respiratory rate adjusted to maintain an end tidal CO2 tension of 35 to 45 mmHg. Variable ventilation was characterized by the oscillation of PEEP from 5 to 10 cmH2O every 4 respiratory cycles, in convencional ventilation group PEEP was set from 5 cmH2O. Ventilatory, hemodynamic parameters, oxidative stress, antioxidant enzymes, Interleukin 8 (IL8) and 17-a (IL17a) and histological analyzes were evaluated; Results: The use of BiPEEP demonstrated improvement in lung compliance and PaO2 in relation to control. The levels of oxidative stress and antioxidant enzymes showed no significant difference. There was no difference in IL17a between groups. In IL8 there was a significant increase in the lung base of control in relation to BiPEEP, and a reduction in the apex of BiPEEP in relation to control. The control group showed changes in lung morphology characterized by cellular infiltrates, a thickening of the alveolar septae and atelectasis, which were attenuated in BiPEEP group; (4) Conclusions: The use of variable ventilation with bi-oscillatory level of PEEP demonstrates a potential ventilatory strategy in an experimental model of ARDS.

In the present work, the effects of ageing treatment on the microstructures of a near-β Ti alloy (TC18) are studied. The influence of ageing treatment on the tensile properties and failure mechanisms are systematically analyzed. It is found that the size and morphology of the primary α (αp) phases are insensitive to ageing temperature and time. Furthermore, the ageing temperature and time dramatically influence the precipitation of the secondary α (αs) phases. Massive αs phases precipitate and gradually coarsen, and finally weave together with increasing the ageing temperature or extending the ageing time. The thickness of αs phases is responsible for the material strengths, while the content of α phases can enhance the material ductility. The ductile characteristics of the alloy with coarser αs phases are more obvious than those with thinner αs phases. Therefore, the ageing treatment is helpful for the precipitation and homogeneous distribution of αs phases, which is essential for balancing the strengths and ductility of the studied Ti alloy.

Compared to tin lead alloys, lead-free tin alloys have lower toxicity, making them more widely used. In this study, Sn-20Bi-0.3Al-xY solders alloys were prepared. The effects of the addition of Y on its microstructure, micro-hardness, wettability and mechanical properties was investigated. The result showed that the addition of Y had significant effect on the refinement of Sn-20Bi-0.3Al-xY. From the spreading tests results, Y increased the wettability of the solders, however when the fraction of Y gradually increased, the wettability reduced. The ultimate tensile and hardness of Sn-20Bi-0.3Al-xY solders alloys were increased as the content of Y increasing.

The concern about consuming eco-friendly products has motivated research in the development of new materials. Therefore, films based on natural polymers have been used to replace traditional polymers. This study consists of a production of films based on gelatin reinforced with black pepper essential oil-loaded nanoemulsions and Cloisite Na⁺. The films were characterized by water vapor permeability, mechanical and thermal properties, surface contact angle, X-ray diffraction and scanning electron microscopy. It was observed that the films containing the nanoemulsion have higher permeability values and an increase in their mechanical resistance. The addition of nanoclay contributed to an increase in the surface hydrophobicity of the film and an increase in the tensile strength at break by about 150%. The addition of essential oil nanoemulsions led to an increase in thermal stability. The presence of clay dispersion contributed to the formation of a surface that was slightly rougher and grainier. The addition of the black pepper essential oil nanoemulsion resulted in an increase in porosity of the gelatin matrix. Through X-ray diffraction analysis, it was possible to conclude that both the polymeric gelatin matrix and the essential oils nanoemulsion are intercalated with the clay dispersion.

The effect of rare earth Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results showed that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites, and significantly improve the toughness of weld metal. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. However, excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties, and the corresponding values were 835MPa of tensile strength and 72 J of impact toughness. These findings suggest that the control of Pr6O11 can be an effective way to improve the impact toughness of weld metal.

The effect of Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results demonstrate that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites in the weld metal, and significantly improve the toughness. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. Excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties.

The main goal of this study was to introduce glycerol as a plasticizer to Polyvinyl Alcohol (PVA) membranes in order to increase their flexibility. The qualities of PVA membranes produced with various glycerol concentrations were evaluated. With the modified PVA membranes containing 5% glycerol, encouraging results were obtained. These membranes had superb optical characteristics and a 90% transmittance rate. This shows that the membranes are suited for applications needing excellent optical clarity since they permit light to travel through with little distortion. Importantly, FTIR analysis demonstrated that the addition of glycerol had no effect on the PVA membranes' chemical composition or structural integrity. In comparison to pure PVA Membrane, the modified membranes' water barrier qualities showed a considerable drop of up to 50%. The membranes are useful for applications requiring moisture management or breathability because of the decline, which points to an increase in permeability to water vapour. The large increase in flexibility, which was achieved by the PVA membranes containing 5% glycerol and beyond the brittleness typically associated with pure PVA, was a noteworthy discovery. The possible applications are expanded due to the increased flexibility, especially in industries where adaptability and flexibility are essential. Additionally, the addition of glycerol improved the thermal stability of the membranes, as they showed increased resistance to breakdown or decomposition at high temperatures. Additionally, the modified membranes' mechanical qualities were better than those of pure PVA, indicating that the glycerol addition improved their overall mechanical performance and tensile strength. PVA membranes were effectively made more flexible by adding 5% glycerol as a plasticizer. This led to membranes with superior optical qualities, reduced water barrier properties, greater flexibility, improved thermal stability, and maybe improved mechanical capabilities. These discoveries open up new opportunities for the use of these flexible PVA membranes in a range of settings, such as flexible packaging, biomedical materials, and other industries that need adaptive and flexible materials.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

In-situ grown C_0.3N_0.7Ti and SiC, which derived from non-oxide additives Ti₃SiC₂, are proposed to densify silicon nitride (Si₃N₄) ceramics with enhanced mechanical performance. Remarkable increase of density from 79.20% to 95.48% could be achieved for Si₃N₄ ceramics with 5vol% Ti₃SiC₂. The capillarity of decomposed Si from Ti₃SiC₂, and in-situ reaction between nonstoichiometric TiC_x and Si₃N₄ were believed to be responsible for densification of Si₃N₄ ceramics. An obvious enhancement of flexural strength and fracture toughness for Ti₃SiC₂ doped Si₃N₄ ceramics was observed. The maximum flexural strength of 795 MPa for Si₃N₄ composites with 5vol% Ti₃SiC₂ and maximum fracture toughness of 6.97 MPa^.m^1/2 for Si₃N₄ composites with 20vol% Ti₃SiC₂ are achieved when mixed powders are hot-press sintered at 1700℃. Pull out of elongated Si₃N₄ grains, crack bridging, crack branching and crack deflection were demonstrated to dominate enhance fracture toughness of Si₃N₄ composites.

Thought runs through the mind like blood runs through our body to keep us alive. Like the mind, the body does not stay inert and is in constant motion. Not a single cell in our body is left inert unless cell is under stress or dying. These scenarios are reflected upon when a person is sick, the person lies in bed with less movement; however, is active when the person is healthy. The topic of mechanical stimulation has emerged due to the increasing understanding of the physical stimulations we face each day. Further understanding of the mechanically-regulated mechanism can help us explore the pathological events in a disease. Here, we reviewed the role of sensory proteins in pathological events that are observed in cardiomyopathy, cancer, respiratory, renal, obesity, genetics, physical injury and bacterial infection. Taken together, sensory proteins are mechanically-activated which assist reception of external physical stimulation and convert into biochemical to trigger intracellular signaling cascade.

Regenerated silk (RS) is a protein-based “biopolymer” that enables the design of new materials; here, we called “bionic” the process of regenerated silk production by a fermentation-assisted method. Based on yeast’s fermentation, here we produced a living hybrid composite made of regenerated silk nanofibrils and a single-cell fungi, the Saccharomyces cerevisiae yeast extract, by fermentation of such microorganisms at room temperature in a dissolution bath of silkworm silk fibers. The fermentation-based processing enhances the beta-sheet content of the RS, corresponding to a reduction in water permeability and CO₂ diffusion through RS/yeast thin films enabling the fabrication of a mechanically robust film that enhances food storage durability. Finally, a transfer print method, which consists of transferring RS and RS/yeast film layers onto a self-adherent paraffin substrate, was used for the realization of heat-responsive wrinkles by exploiting the high thermal expansion of the paraffin substrate that regulates the applied strain, resulting in a switchable coating morphology from the wrinkle-free state to a wrinkled state if the food temperature overcomes a designed threshold. We envision that such efficient and smart coatings can be applied for the realization of smart packaging that, through such a temperature-sensing mechanism, can be used to control food storage conditions.

The application of metal-matrix composite coatings for protecting and improving the service life of sliding components has demonstrated to have the potentials of meeting the requirements of a diverse range of engineering industries. Recently, a significant body of research has been devoted to study the mechanical and tribological performance of dispersion-strengthened MCrAlY coatings. These coatings belong to a class of emerging wear-resistant materials, offering improved properties and being considered as promising candidates for the protection of engineering structural materials exposed to tribological damage, especially at elevated temperature regimes. This paper attempts to comprehensively review the different reinforcements used in the processing of MCrAlY-based alloys and how they influence the mechanical and tribological properties of the corresponding coatings. Further, the major fabrication techniques together with their benefits and challenges are also reviewed. Discussion on the failure mechanisms of these coatings as well as the main determining factors are also included. In addition, a comprehensive survey of studies and investigations in recent times are summarized and elaborated to further substantiate the review.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

Aim: The aim of this study was to estimate the number of nurses who independently care for pa-tients with severe respiratory failure receiving mechanical ventilation (MV) or veno-venous ex-tracorporeal membrane oxygenation (VV-ECMO). Additionally, the study analyzed the actual role of nurses in the treatment of patients with MV and VV-ECMO. Methods: We conducted a cross-sectional study using postal surveys. The study included 725 Japanese intensive care units (ICUs). Descriptive statistics were conducted. Results: Among the 725 ICUs, we obtained 302 re-sponses (41.7%) and analyzed 282 responses. The median number of nurses per bed was 3.25. The median proportion of nurses who independently cared for patients with MV was 60% [IQR: 42.3-77.3]. The median proportion of nurses who independently cared for patients with VV-ECMO was 46.9 (35.7-63.3%) in the ICU experiencing VV-ECMO use. Concerning task-sharing, 33.8% of ICUs and nurses did not facilitate weaning from MV. Nurses always ti-trated sedatives in 44.5% of ICUs. Conclusion: Nurse staffing might be inadequate in all ICUs, es-pecially for severe respiratory failure. The proportion of competent nurses for caring for severe respiratory failure in ICUs should be considered when determining the work force of nurses.

Friction stir processing (FSP), a severe plastic deformation process, was applied on commercially pure Ti to obtain an improved microstructure. The process yielded a refined microstructure and higher mechanical properties at room temperature (RT). Yet the microstructure was found to contain bright bands demonstrating high hardness values of about 500 HV. High resolution scanning electron microscopy (HRSEM) as well as electron back scattering diffraction (EBSD) analysis indicated that these bands were composed of extra-fine equiaxed α-Ti grains with an average radius of 1-2 microns. In addition, a retained β-phase was detected at the boundaries of these α-Ti grains, together with a small quantity of separate β grains. The results of a fractography study conducted on broken tensile specimens showed that the FSP’ed material was free of defects and that the fracture started at these bands. It is proposed that these bright bands are due to excessive deformation occurring during the processing stage, leading to an accelerated dynamic recrystallization (DRX) process. In turn, these heavy deformation regions act as a strengthening constituent, making the material superior to the parent material as far as its mechanical RT properties are concerned. Consequently, this means that FSP of CP-Ti has the potential to serve as an industrial means of improving the mechanical properties of the material.

Regional mechanics of the heart is vital in the development of accurate computational models for the pursuit of relevant therapies. Challenges related to heart dysfunctioning are the most important sources of mortality in the world. For example, myocardial infarction (MI) is the foremost killer in sub-Saharan African countries. Mechanical characterisation plays an important role in achieving accurate material behaviour. Material behaviour and constitutive modelling are essential for accurate development of computational models. In most cases previously, the mechanical properties of the heart myocardium were assumed to be homogeneous. The main objective of this paper is to determine the mechanical material properties of healthy porcine myocardium in three regions, namely left ventricle (LV), mid-wall/interventricular septum (MDW) and right ventricle (RV). The biomechanical properties of the pig heart RV, LV and MDW were characterised using biaxial testing. The biaxial tests show the pig heart myocardium behaves non-linearly, heterogeneously and anisotropically. In this study, it was shown that RV, LV and MDW may exhibit slightly different mechanical properties. Data presented here may be helpful in regional tissue mechanics, especially for the understanding of various heart diseases and development of new therapies.

Hydrogels are three-dimensional crosslinked materials known for their ability to absorb water, exhibit high flexibility, biodegradability, biocompatibility, and mimic properties of different tissues in the body. However, their application is limited by inherent deficiencies in mechanical properties. To address this issue, reduced graphene oxide (rGO) and tannins (TA) were incorporated into alginate hydrogels (Alg) to evaluate the impact of the concentration of these nanomaterials on mechanical and adhesive, as well as cytotoxicity and wound healing properties. Tensile mechanical tests demonstrated improvements in tensile strength, elastic modulus, and toughness upon the incorporation of rGO and TA. Additionally, the inclusion of these materials allowed a greater energy dissipation during continuous charge-discharge cycles. However, the samples did not exhibit self-recovery under environmental conditions. Adhesion was evaluated on pig skin, revealing that higher concentrations of rGO led to enhanced adhesion, while the concentration of TA did not significantly affect this property. Moreover, adhesion remained consistent after 10 adhesion cycles, and contact time before the separation between the material and the surface did not affect this property. The materials were not cytotoxic and promoted healing in human fibroblast model cells. Thus, an Alg/rGO/TA hydrogel with enhanced mechanical, adhesive, and wound healing properties was successfully developed.

Aluminum alloy Al 2024-T3 were successfully joined using friction stir spot jwelding joining (FSSW). Satisfactory joint strengths were obtained at different welding parameters (tool rotational speed, tool plunge depth, dwell time) and tool pin profile (straight cylindrical, triangular and tapered cylindrical). Resulting joints were welded with welded zone. The different tools significantly influenced the evolution on the stir zone in the welds. Lap-shear tests were carried out to find the weld strength. Weld cross section appearance observations were also done. The macrostructure shows that the welding parameters have a determinant effect on the weld strength (x: the nugget thickness, y: the thickness of the upper sheet and SZ: stir zone). The main fracture mode was pull out fracture modes in the tensile shear test of joints. The results of tensile shear tests showed that the tensile-shear load increased with increasing rotational speed in the shoulder penetration depth of 0.2 mm. Failure joints were obrerved in the weld high shoulder penetration depth and insufficient tool rotation.

Aluminum matrix nanocomposites have been the subject of much attention due to their extraordinary mechanical properties and thermal stability. This research focuses on producing and characterizing an aluminum matrix reinforced with silicon carbide (SiC) nanometric particles. The conventional powder metallurgy route was used to produce the nanocomposites, and the dispersion and mixing process was carried out by ultrasonication. The conditions of the dispersion and the volume fraction of the SiC were evaluated in the production of the nanocomposites. Microstructural characterization was carried out using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD). Mechanical characterization was carried out using hardness and tensile tests. The dispersion agent was investigated, and isopropanol leads to better dispersion with fewer agglomerates. Increasing the volume fraction of the reinforcement improves the hardness of the nanocomposites. However, greater agglomeration of the reinforcement is observed for larger volume fractions. The greatest increase in hardness (77% increase compared to the hardness of the Al matrix) is obtained with 1.0 vol % of SiC, corresponding to the sample with the best dispersion. The mechanical characterization through tensile tests attests to the effect of the reinforcement on the Al matrix. The main strengthening mechanisms identified were the load transfer, the texture hardening, Orowan strengthening, and the increase in the density of dislocations in the nanocomposites.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

In 2011 over 1.7 million people were hospitalized because of a fragility fracture, and direct costs associated with osteoporosis treatment exceeded 70 billion dollars in the United States. Failure to reach and maintain optimal peak bone mass during adulthood is a critical factor in determining fragility fracture risk later in life. Physical activity is a widely accessible, low cost, and highly modifiable contributor to bone health. Here, we will review the evidence linking exercise and physical activity to bone health in women. Bone structure and quality will be discussed, especially in the context of clinical diagnosis of osteoporosis. We will review the mechanisms governing bone metabolism in the context of physical activity and exercise. Questions such as, when during life is exercise most effective, and what specific types of exercises improve bone health, will be addressed. Finally, we will discuss some emerging areas of research on this topic, and will summarize areas of need and opportunity.

The current work shows the optimization in the preparation of nanosized titanium carbide (TiC) in-situ through mechanical alloying (MA). Metallic titanium (Ti) powders, along with two carbon sources, carbon nanotubes (CNTs), and stearic acid (SA), were used to reduce the particle size using a high-energy Spex800 mill. The combined use of 2 wt % of these carbon sources and n-heptane as a liquid process control agent (PCA) proved crucial in generating nanoscale powder composites through a simple and scalable synthesis process within a 4-hour timeframe. The use of 20 wt % of both carbon sources was compared to determine the ability of CNTs to form carbides and the decomposition of PCAs during mechanical milling. The result reveals structures like nanoblocks and nanolumps with and important size reduction. The structure and morphology of the composites and starting materials were evaluated through x-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM).

The solid-state welding method known as friction stir welding (FSW) bonds two metallic work parts, whether the same or different, by plastically deforming the base metal. The frictional resistance between both metallic work pieces causes them to produce heat, which produces plastic deformation and welds them. However, the weldability and strength of FSW joints mainly depend on the FSW parameters. This review work highlights the previous research work on the FSW parameters and their effects on the weldability and quality of the aluminum alloys joined with similar and dissimilar metals through the FSW method. About 150 research studies were systematically reviewed, and the articles included data from peer-reviewed journals. It has been concluded that the key parameters, including welding speed, “rotational speed”, “plunge depth”, “spindle torque”, “shoulder design”, “base material”, “pin profile” and “tool type", significantly affect the weldability of the aluminum joint through the FSW method. Also, the selection of these parameters is important and fundamental as they directly affect the joint. It is recommended that future work focus on FSW for aluminum. Among these, the most essential is the application of artificial intelligence (AI) techniques to select the optimum FSW parameters for aluminum welding.

The use of acoustic and magnetic methods of non-destructive testing to detect zones of stable localization of deformation in order to assess and predict the performance of long-term equipment is of scientific and practical interest at present. A structural-mechanical criterion has been developed, that reflects the revealed relationships between the structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests in the metal of long-term equipment made of structural 0.2 С steel and heat-resistant 0,12C-1Cr-1Mo-1V steel. The values of the structural-mechanical criteria Ks.-m for structural 0.2 С steel and for heat-resistant 0,12C-1Cr-1Mo-1V steel, corresponding to the moment of stable localization of deformation, are established. At the same time, it is recommended to replace the checked equipment nodes due to the exhaustion of the resource. The proposed and justified approach to assessing and predicting the performance and residual life of long-term power equipment, based on the identified relationships between the structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests and the calculation of the structural-mechanical criterion, was applied at a number of power plants in the Kemerovo region – Kuzbass. A methodology has been developed for evaluating the residual life, based on the identification and use of relationships between structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests and the calculation of a structural-mechanical criterion.

The paper concerns with the identification of current communication technologies and software functionalities from the field of digitalization and Industry 4.0, from the point of view of benefits and applicability for the machine manufacturer. In order to identify the relevant technologies and functionalities, both a descriptive and statistical literature research was carried out. As a result, both the currently most widespread technologies and eleven IT functionalities relevant to mechanical engineers were identified and described in terms of their application and implementation. In addition, a knowledge gap in the area of industry transfer in the field of Industry 4.0 / Digitalization was identified

The phosphogypsum (PG) pile of solid waste is of immense proportions and poses a grave threat to the ecological environment, with its reserves steadily increasing year after year. The urgent need for large-scale consumption and high-quality utilization of PG in industrial production has become apparent. The present study provides a comprehensive analysis of the correlation be-tween the macroscopic mechanical properties and microstructure of PG, elucidating the crystal morphology characteristics in different phases and outlining the crystallization preparation pro-cess. By integrating the physical and chemical properties of diverse PG phases with the intricacies associated with its preparation process, it is imperative to explore avenues for its high-value utili-zation, investigate possibilities for industrial-scale production, and analyze and predict the appli-cation trends and developmental directions in comprehensive PG utilization. These endeavors hold immense significance in guiding the realization of resource utilization potential inherent in PG.

The educational and play-related activities of children are proceeded mainly indoors in a kin-dergarten. The exposure of children to high concentrations of PM2.5 and CO2 indoors have leaded to various harmful effects and negatively impact educational outcomes in a kindergarten. Therefore, this study presents a numerical model of CO2 and PM2.5 concentration based on two classrooms in a kindergarten. Using this numerical model, we present different scenarios of oper-ating mechanical ventilation and air purifiers in kindergartens with the aim of optimizing for reducing the concentrations of CO2 and PM2.5. We found that the amount of ventilation required to maintain good air quality, per child, was approximately 20.4 m3/h. However, we also found that as the amount of ventilation increased, so did the concentration of indoor PM2.5; we found that this issue can be resolved through the use of a high-grade filter (i.e., a MERV 13 grade filter with a collection efficiency of 75%). This study provides a scientific basis for reducing PM2.5concentrations in kindergartens, while keeping CO2 levels low.

Polylactic acid (PLA) was modified with three types of MVOs, which are the epoxidized soybean oil (ESBO), maleinized sunflower oil (MSO) and maleinized olive oil (MOO), at different weight fractions. A co-rotating twin screw extruder was used to produce composite materials by melt mixing process. The effect of MVOs content, from 2.5% to 10%, on the morphology, mechanical properties, density and water absorption were investigated in detail. Addition of ESBO and maleinized vegetable oils leads to a slight decrease in density of PLA from 1.252 to 1.231 g/cm3. As the concentration of MVO in PLA increases, the amount of water absorption also increased and the highest water absorption value was observed in P10MSO. In general, the elastic modulus (EM) was slightly changed by the addition of MVO to PLA, while the tensile strength (TS) decreased. Due to the plasticizing effect of MVOs, an increase in the Izod impact strength was obtained.

Starch is a biopolymer with wide potential for the generation of new biodegradable packages due to its high availability and low price. However, due to its weak functional properties, it is necessary to limit the interaction of some hydroxyl, and to evaluate blends with other polymers to improve their performance. Glycerol plasticized acetylated corn starch films were developed by the casting method, and the impact of incorporating chitosan (TPS:CH) at various proportions (75:25, 50:50, and 25:75 v/v) was studied. The effect of the chitosan ratios on the films' physical, mechanical, water vapor barrier, and thermal properties was evaluated. Chitosan protonated amino groups promote the formation of intermolecular bonds, improving the tensile strength, the thermal stability, the water adsorption capacity, and the gas barrier of starch films. Where the film composed of TPS25-CH75 was the one that presented the best barrier to water vapor. These composite films are a good option for development of biodegradable packaging.

Radical prostatectomy (RP) is one of the recommended treatments to achieve oncological outcomes in localized prostate cancer. However, radical prostatectomy is a major abdominopelvic surgery. Venous thromboembolism (VTE) is a well-known complication associated with surgical procedures including RP. There is a lack of consensus regarding VTE prophylaxis in urological procedures. The aim of this systematic review was to investigate different aspects of VTE in post-Radical Prostatectomy patients. A comprehensive literature search was performed, and relevant data were extracted. The primary aim was to perform a systematic review and meta-analysis (wherever possible) of VTE occurrence in post-RP patients in relation to surgical approach, pelvic lymph node dissection, and type of prophylaxis (mechanical or combined prophylaxis). The secondary aim was to investigate- the incidence and other risk factors of VTE in post-RP patients. A total of 16 studies were included for quantitative analysis. Statistical methods for analysis included the DerSimonian-Laird random effects. We were able to conclude that the overall incidence of VTE in post-radical prostatectomy is 1% and minimally invasive procedures (MIS), including laparoscopic as well as robotic procedures for radical prostatectomy and RP without pelvic lymph node dissection (PLND) are associated with less risk of developing VTE. Additional pharmacological prophylaxis to mechanical methods may not be necessary in all cases and should be considered in high-risk patients only.

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FR). Significant amounts of FR are usually required to effectively affect the polymer burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC) and pentaerythritol (PER) and its composites containing additionally short basalt fibers (BF). Composites manufactured by twin-screw extrusion were subjected to four reprocessing cycles by injection molding, comprehensively analyzing structural, mechanical, and fire behavior changes in each cycle. The obtained results confirmed the safety of using the proposed flame-retardant system for polyamide, processed under the recommended process parameters, without the risk of significant changes in the structure despite the partial increase in flammability caused mainly by the degradation of the polymer.

The main motive of this study was to find an auxiliary application of the discarded agricultural remnants and poultry waste. Rice straw and chicken feathers are disposed off as landfills or incinerated causing pollution and environmental threats after their primary consumption. In this study epoxy composites were made using varying proportions of these raw and alkali treated materials. Flexural strength of the composites decreased till 35% fiber loading, followed by an increase. Chicken feather composites showed increased impact strength with fiber addition. Alkali treatment improved the mechanical properties of rice straw composites. Alkali treated chicken feather composites showed better impact strength but no significant change in flexural strength. Hybrid composites explicated enhanced properties both before and after alkali treatment corroborating noteworthy interfacial adhesion and synergistic effect of these fibers as ascertained from SEM images. The study evinced a better option for averting environmental problems by recycling these disposed materials.

Hydrogel wound dressings hold great potential in eliminating bacteria and accelerating the healing process. However, it remains a challenge to fabricate hydrogel wound dressings that simultaneously exhibit excellent mechanical and photothermal antibacterial properties. Here we report the development of polydopamine-functionalized graphene oxide/calcium alginate/Polypyrrole cotton fabric-reinforced hydrogels (abbreviated as rGO@PDA/CA/PPy FHs) for tackling bacterial infections. The mechanical properties of hydrogels were greatly enhanced by cotton fabric reinforcement and an interpenetrating structure, while excellent broad-spectrum photothermal antibacterial properties based on the photothermal effect were obtained by incorporating PPy and rGO@PDA. Results indicated that rGO@PDA/CA/PPy FHs exhibited superior tensile strength in both the warp (289±62.1N) and weft directions (142±23.0N) similar to cotton fabric. By incorporating PPy and rGO@PDA, the swelling ratio was significantly decreased from 673.5% to 236.6%, while photothermal conversion performance was significantly enhanced with a temperature elevated to 45.0 ℃. Due to the synergistic photothermal properties of rGO@PDA and PPy, rGO@PDA/CA/PPy FHs exhibited excellent bacteria-eliminating efficiency for S. aureus (0.57%) and E. coli (3.58%) after exposure to NIR for 20 min. We believe that the design of fabric-reinforced hydrogels could serve as a guideline for developing hydrogel wound dressings with improved mechanical properties and broad-spectrum photothermal antibacterial properties for infected wound treatment.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Paper is a material whose mechanical properties are highly dependent on humidity and temperature. Which naturally also builds the relationship between the stiffness and strength of corrugated board and changing weather conditions. In this paper, attention is focused on the dependence of the physical properties of the cardboard on changes in humidity and temperature, which undergo dynamic fluctuations both during the production of corrugated board and during its storage. Two techniques were used to test this effect, namely numerical homogenization and global sensitivity analysis. Both methods were implemented to determine the theoretical relationships between the change in humidity and/or temperature in each layer of corrugated board and its global bending, compression and shear stiffness. The procedure was used to analyze different types of 5-ply and 3-ply cardboard. The obtained results allowed to build a complete map of the relationship between the change in humidity of selected layers and the strength characteristics of the full assembly.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

Synthetic materials such as Carbon, Kevlar, and Glass fibers are extensively utilized in various industries due to their superior characteristics including high stiffness, great strength, low den-sity, and high wear resistance, these advantages contributed to making them widespread in ap-plications like; aerospace, automobile, civil and electronics. This research is carried out to enhance the creep compliance of epoxy composite material by considering two types of fibers as reinforcement. A composite material is produced by combining two fibers, Kevlar fiber mixed with sika epoxy resin, along with Carbon fiber also mixed with sika epoxy resin using a Hand-Layup process. Experiments and numerical modeling are examined to offer a comprehensive understanding creep behavior of epoxy composite material in different weight ratios. Burger and Prony models are used to represent stress relaxation and creep strain of Visco-elastic material. According to the results, sika epoxy resin reinforced with Kevlar and Carbon fibers exhibits enhancement in the mechanical properties compared with pure epoxy. The use of Kev-lar/Sika epoxy composite results in higher creep compliance and modulus of elasticity compared with Carbon/Sika epoxy composite.

The effect of Al or Cu content on the microstructure and mechanical properties of continuous casting and extrusion Zn alloys has been studied by room temperature tensile test, X-ray diffraction, and scanning electron microscope. With the increase of Al content, the microstructure of continuous casting and extrusion Zn alloys slightly coarsens and the lamellar eutectic structure increases. The changes in the above structural factors result in a slight decrease in strength and a significant increase in elongation of Zn-Al alloys. The strength of Zn alloys increases as the Cu content increases, due to the increased content and size of the second phase in the Zn alloys. This means that the mechanical properties of Zn alloys can be adjusted by continuous casting and extrusion process, and the improvement of equipment capacity can improve the structure and morphology of the alloys.

Rationale: Examining trends in patient characteristics, processes of care and outcomes, across an epidemic, provides important opportunities for learning. Objectives: To report and explore changes in admission rates, patient characteristics, processes of care and outcomes for all patients with COVID-19 admitted to intensive care units (ICUs) in England, Wales and Northern Ireland. Methods: Population cohort of 10,287 patients with COVID-19 in the Case Mix Programme national clinical audit from 1 February to 2 July, 2020. Analyses were stratified by time period (pre-peak, peak, post-peak) and geographical region. Multivariable logistic regression was used to estimate differences in 28-day mortality, adjusting for patient characteristics over time. Main results: Admissions to ICU peaked simultaneously across regions on 1 April, with ongoing admissions peaking ten days later. Compared with pre- and post-peak periods, patients admitted during the peak were slightly younger but had greater respiratory and renal dysfunction. Use of invasive ventilation and renal replacement reduced over time. Twenty-eight-day mortality reduced from 43.5% (95% CI 41.6% to 45.5%) pre-peak to 34.3% (95% CI 32.3% to 36.2%) post-peak; a difference of −8.8% (95% CI: −5.2%, −12.3%) after adjusting for patient characteristics. London experienced the highest admission rate and had higher mortality during the peak period but a greater reduction in post-peak mortality. Conclusion: This study highlights changes in patient characteristics, processes of care and outcomes, during the UK COVID-19 epidemic. After adjusting for the changes in patient characteristics and first 24-hour physiology, there was substantial improvement in 28-day mortality over the course of the epidemic.

To investigate the effect of Polyvinylpyrrolidone (PVP) addition and consequently porosity, two different sets of membranes are manufactured, since PVP is a widely used poring agent which has an impact on the mechanical properties of the membrane material. The first set (PAN 1) includes PAN and the necessary solvent while the second set (PAN 2) is made of PAN and PVP. These membranes are put through several characterisation processes including tensile testing. The obtained data are used to model the static behaviour of the membranes with different geometries, but similar loading and boundary conditions that represent their operating conditions. This modelling process is undertaken by using finite element method. The main idea is to investigate how geometry affects the load-carrying capacity of the membranes. Alongside membrane modelling, their materials are modelled with representative elements with hexagonal and rectangular pore arrays (RE) to understand the impact of porosity on the mechanical properties. Exploring the results, the best geometry is found as the elliptic membrane with the aspect ratio 4 and the better RE as the hexagonal array which can predict the elastic properties with an approximate error of 12%.

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

In this study, carbon blocks were fabricated using isotropic coke and coal tar pitch as raw materials, with a variation in pressure during cold isostatic pressing (CIP). The CIP pressure was set to 50, 100, 150, and 200 MPa, and the effect of the CIP pressure on the mechanical and electrical properties of the resulting carbon blocks was analyzed. Microstructural observations confirmed that after the kneading, the surface of isotropic coke was covered with the pitch components. Subsequently, after the CIP, granules, which were larger than isotropic coke and the kneaded particles, were observed. The formation of these granules was attributed to the coalescence of kneaded particles under the applied pressing pressure. This granule formation was accompanied by the development of pores, some remaining within the granules, while others were extruded, thereby existing externally. The increase in the applied pressing pressure facilitated the formation of granules, and this microstructural development contributed to enhanced mechanical and electrical properties. At a pressing pressure of 100 MPa, the maximum flexural strength was achieved at 33.3 MPa, and the minimum electrical resistivity was reached at 60.1 μΩm. The higher the pressing pressure, the larger the size of the granules. Pores around the granules tended to connect and grow larger, forming crack-like structures. This microstructural change led to degraded mechanical and electrical properties. The isotropic ratio of the carbon blocks obtained in this study was estimated based on the coefficient of thermal expansion (CTE). The results confirmed that all carbon blocks obtained proved to be isotropic. In this study, a specimen type named CIP-100 exhibited the best performance in every aspect as an isotropic carbon block.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

In recent decades, low-yielding seismic devices based on the use of friction dampers have emerged as an excellent solution for the development of building structures with improved reparability and resilience. Achieving an optimal design for such low-yielding seismic devices requires precise control of bolt preloading levels and predictability of the friction coefficient (CoF) between the damper interfaces. While various types of friction devices exist, capable of providing significant energy dissipation, ongoing research is focused on the development of novel friction materials that exhibit a stable hysteretic response, high CoF values, minimal differences between static and dynamic CoF, and predictable slip resistance. In this context, an experimental campaign was conducted at the STRENGTH Laboratory of the University of Salerno to evaluate the behaviour of new friction shims employing specially developed metal alloys. Specifically, the influence of the characteristics of the contact surfaces in the sliding area on the behaviour and performance of the friction device was analysed. The tests followed the loading protocol recommended by EN12159 for seismic device qualification. Monitored parameters included preloading force values and the evolution of slip resistance. The friction value was determined, along with its degradation over time. Finally, the material's performance in terms of hysteretic behaviour was assessed, providing a comparison of the tested specimens in terms of slip force degradation and energy dissipation capacity.

Mechanical ventilation systems used in houses are designed to reduce carbon dioxide emissions while minimizing the energy loss resulting from ventilation. However, increase in indoor fine particulate (PM2.5) concentration because of external PM2.5, influx through the ventilation system poses a problem. In this study, we analyzed the changes in indoor PM2.5 concentrations via dis-tinguishing between cases of high and low outdoor PM2.5 concentrations, considering the effi-ciency of filters used in residential mechanical ventilation systems. When using minimum effi-ciency reporting value (MERV) 10 filters in the ventilation system, the outdoor PM2.5 concentra-tion was 5 μg/m³; the indoor PM2.5 concentration became 73% after 60 min compared to the ini-tial. When the outdoor PM2.5 concentration was 30–40 μg/m³, the indoor PM2.5 concentration reached 91%. However, when MERV 13 filters were used, the indoor PM2.5 concentration con-sistently dropped to 73–76% regardless of the outdoor PM2.5 concentration. Furthermore, by comparing the established equation with the mass-balance model, the error was confirmed to be within 5%, indicating good fit. This allows the prediction of indoor PM2.5 under various condi-tions when using mechanical ventilation systems, enabling the formulation of strategies to maintain indoor PM2.5 as recommended by the World Health Organization.

Studies have shown the benefits of endovascular treatment (EVT) in adult stroke cases, but its application in pediatric stroke remains controversial. Despite evidence of improved outcomes in adults, there are no established recommendations for EVT in children. Conducting individual case reports and case series is vital to understanding its potential advantages and disadvantages in this context. This case report presents a 9-year-old boy who experienced basilar artery occlusion leading to a stroke and was effectively treated with mechanical thrombectomy.

Cancer cells exhibit aberrant extracellular matrix mechanosensing due to altered expression of mechanosensory cytoskeletal proteins. Aberrant mechanosensing of the tumor microenvironment (TME) by cancer cells has been shown to be associated with cancer development and progression. Recent studies show that altered mechanosensing changes the mechanobiological properties of cells, and, in turn, cells become susceptible to mechanical perturbations. Due to an increasing understanding of cell biomechanics and cellular machinery, several approaches have emerged to target the mechanobiological properties of cancer cells and cancer-associated cells to inhibit cancer growth and progression. In this review, we summarize the progress that happened in the development of mechano-based approaches to target cancer by interfering with the cellular mechanosensing machinery and overall TME.

The global production of macadamia nuts has witnessed a significant increase, resulting in the accumulation of large quantities of discarded nutshells. These nutshells possess remarkable hardness and toughness, comparable to aluminum. Incorporating natural fillers to enhance the properties of composite materials for various applications, including light duty, structural, and semi-structural purposes, is a common practice. Given their inherent hardness and toughness, macadamia nutshells present an intriguing choice as fillers, provided that the manufacturing conditions are economically viable. With the urgent need to shift towards natural fillers and reduce reliance on synthetics, exploring macadamia nutshells as components of natural fiber composites becomes imperative. This review aims to comprehensively examine the existing body of knowledge on macadamia nutshells and their bio-synthetic polymer composites, highlighting key research findings, achievements, and identifying knowledge gaps. Furthermore, the article will outline prospective areas of focus for future research endeavors in this domain, aligning with the universal goal of minimizing synthetic materials.

Two-dimensional (2D) materials have been a research hot topic in the passed decades due to their unique and fascinating properties. Among them, mechanical properties plays an important role for their application. However, there lacks an effective tool for high-throughput calculating, analysing and visualizing the mechanical properties of 2D materials. In this work, we present, mech2d package, a highly automated toolkit for calculating and analysing second-order elastic constants (SOECs) tensor and relevant properties of 2D materials with considering their symmetry. In the mech2d, the SOECs can be fitted by both strain-energy and stress-strain approach, where the energy or strain can be calculated by first-principles engine, such as VASP. As a key feature, the mech2d package can automatically submit and collect the tasks from local or remote machine with robust fault-tolerant ability, make it suitable for high-throughput calculation. The present code has been validated by several common 2D materials, including graphene, black phosphorene, GeSe2 and so on.

In contrast to the traditional fillers, clay, in particular, natural smectite clay represents an environmentally significant alternative to improve the properties of polymers. Compared to con-ventional nanofillers, smectite clay can effectively enhance the physical and mechanical properties of polymer nanocomposites with a relatively small amount of addition (< 5 wt%). The present study focuses on investigating the reinforcing efficiency of different amounts (up to 5 wt%) of a natural Brazilian smectite clay on the mechanical and thermal properties of poly(butylene terephthalate) (PBT) nanocomposites. Natural Brazilian clay modified by addition of quaternary salt and sodium carbonate (MBClay) was infused into the PBT polymer by melt extrusion, using a twin-screw extruder. It was found that the best properties for PBT were obtained at 3.7 wt% of modified BClay. Tensile strength at break exhibited an increase of about 60 %, flexural strength increased by 24 % and flexural modulus increased by 17 %. In addition, an increase in the crystallinity percentage of PBT/BClay nanocomposite was confirmed by DSC and XRD analysis, and a gain of about 45 % in HDT was successfully achieved due to incorporation of 3.7 wt% of MBClay.

Hippotherapy is a popular rehabilitation method for children with cerebral palsy (CP), which is done by riding an actual horse or a horse riding simulator (HRS) device. Riding a real horse is more expensive than using an HRS device due to its high maintenance cost. However, most HRS devices commonly sold in the market are designed as exercise devices, not rehabilitation devices. Most of them are designed to simulate a horse's walk, trot, canter, or gallop gait at various speeds. Hippotherapy aims to improve the walking ability of CP patients. Therefore, the device should aim to replicate the walking gait of a healthy human, the end goal of hippotherapy. This problem motivates us to design and build a specialized HRS device replicating the walking gait of a healthy human that is suitable for hippotherapy, which is achievable by simulating a horse walking gait with several adjustments. We first studied and observed the walking gait cycle of a horse, then analyzed and derived a formulation of it. We then continue by designing an HRS device using a single electrical rotational motor and mechanical means to replicate the walking gait of a horse, then tune it to an extent to replicate a human walking gait. To measure the performance of our design, we compare the gait of the user when riding our device versus walking.

Alternating TiB2-dcMS and Cr-HiPIMS layers are used to fabricate TiB2/Cr multilayer films. In-troducing a 5-nm-thick Cr interlayer deposited under a substrate bias of -60 V produces slight increases of both film hardness and elastic modulus. The TEM observation indicates that the Cr grains favor epitaxially growth on TiB2 interlayer, forming a coherent TiB2/Cr interface. This produces the hardness increasement. Mechanic measurement by using AFM illustrates that the coherent interface increases the elastic modulus of the Cr up to ~280 GPa, which is significantly higher than bulk material.

The paper deals with the problems of direct kinematics related to a 2T6R robot, the direct kinematics of the plane mechanism of the robot. The direct kinematics of this proposed new robot help to study the movement, including the dynamic one, to determine the forces in the mechanism and to model the possible trajectories of the final effector point, thus determining the robot's working space and some of its multiple possible uses. Two totally different methods were used to verify the calculation relations, the results obtained by both methods being practically identical. The first method used is an original trigonometric method, and the second is an original geometrically analytical method.

The article discusses the results of investigations performed during a thermo-mechanical treatment of forgings made of chromium-molybdenum 42CrMo4 grade steel. The treatment was realized during a regular series production. The forging process was combined with a heat treatment carried out directly after forging on a specially adapted station. Such a production technology will make it possible to eliminate the step of repeated heating of the forgings. On the example of an element of a steering gear, it was demonstrated how it is possible to perform an isothermal annealing process starting from the temperature at which the trimming of the forgings ends. During the cooling of the forgings, it is enough to maintain the temperature at the proper level in order for the exothermal phase transformation of austenite into pearlite to take place. With an appropriate design of the processing line, the heat released during the transformation could be used to maintain the applied temperature, thus limiting the consumption of energy needed to power the devices. The test results show that, with the properly selected temperature of isothermal annealing, it is possible to obtain an equilibrial ferritic-pearlitic structure in the required hardness scope. Introducing such a solution into the industrial practice would allow significant savings of the energy used for the heat treatment.

The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites. Pure Mg, Mg-3Sn alloy, and Mg-3Sn+0.2GNP alloy-nanocomposite were synthesized by powder metallurgy followed by hot extrusion. The microstructural characteristics of the bulk extruded samples were explored using X-ray diffraction, field-emission scanning electron microscopy, and optical microscopy and their mechanical properties were compared. The microhardness, tensile strength, and compressive strength of the Mg-3Sn alloy improved when compared to those of monolithic Mg sample and further improvements were displayed by Mg-3Sn+0.2GNP alloy-nanocomposite. No significant change in the compressive strain to failure was observed in both the alloy and the alloy-nanocomposite with respect to that of the pure Mg sample. However, an enhanced tensile strain to failure was displayed by both the alloy and the alloy-nanocomposite.

The paper presents an analysis of the possibility of producing traction brushes from waste materials. Brushes are used to ensure good electrical contact between the rail and the pantograph. Slides are produced in the process of hot pressing, with parameters of heating up to max 175 ⁰C, at the minimal pressure value of 200 MPa. The developed brushes with a high (55-60%) content of recycled materials have comparable characteristics to commercial brushes, and some of the prototypes are even more durable and break-resistant.

In this research, the feasibility of using bottom ashes generated by the combustion of biomass (olive pruning and pine pruning) as a source of aluminosilicates (OPBA) has been studied, replacing the metakaolin precursor (MK) in different proportions (0, 25, 50, 75 and 100 wt. % substitution) for the synthesis of geopolymers. As alkaline activator an 8 M NaOH solution and a Na2SiO3 have been used. The geopolymers were cured 24 hours in a climatic chamber at 60 ° C in a water-saturated atmosphere, subsequently demoulded and cured at room temperature for 28 days. The results indicated that the incorporation of OPBA waste, which have 19.7 wt. % of Ca, modifies the characteristics of the products formed after alkaline activation. In general terms, the incorporation of increasing amounts of calcium-rich ashes results in geopolymers with higher bulk density. The compressive strength increases with the addition of up to 50 wt. % of OPBA with respect to the control geopolymers, contributing the composition of the residue to the acquisition of a better behaviour mechanical. The results indicate the potential use of these OPBA waste as raw material to produce unconventional cements with 28-day curing strengths greater than 10 MPa, and thermal conductivities less than 0.35 W/mK.

In this work we produced biochar by coffee waste and use it as filler in epoxy resin composite with the aim to increase their electrical properties. The biochar and biochar based composite electrical conductivity were studied in function of applied pressure and compared with carbon black and carbon black composite. The applied pressure has the aim to investigate the behaviour of filler in powder or dispersed in composite in function of compression. Results showed that even if the coffee biochar has less conductivity if compared with carbon black in powder form, it has better conductivity in composite if compared with carbon black. Composite mechanical properties were tested and they are generally improved respect to neat epoxy resin.

Alumina dispersion-strengthened copper, Glidcop, is used widely in high-heat-load ultra-high-vacuum components for synchrotron light sources (absorbers), accelerator components (beam intercepting devices) and in nuclear power plants. Glidcop has similar thermal and electrical properties to OFE (oxygen free electrical) copper, but has superior mechanical properties, thus making it a feasible structural material; its yield and ultimate strength are equivalent to those of mild-carbon steel. The purpose of this work has been to develop a brazing technique to join Glidcop to Mo, using a commercial Cu-based alloy. The effects of the excessive diffusion of the braze along the grain boundaries on the interfacial chemistry and joint microstructure, as well as on the mechanical performance of the brazed joints, has been investigated. In order to prevent the diffusion of the braze into the Glidcop alloy, a copper barrier layer has been deposited on Glidcop by means of RF-sputtering.

The management of existing water distribution system (WDS) is challenged by ageing of infrastructure, population growth, increasing of urbanization, climate change impacts and environmental pollution. Therefore, there is a need for integrated solutions that support decision makers to plan today, while taking into account the effect of these factors in the mid and long term. The paper is part of a more comprehensive project, where advanced hydraulic analysis for WDS is coupled with a dynamic resources input-output analysis model. The proposed modeling solution can be used to optimize the performance of a water supply system while considering also the energy consumption and consequently the environmental impacts. Therefore, as a support tool in the management of a water supply system also in the intervention planning. Here a possible application is presented for rehabilitation/replacement planning while maximizing the network mechanical reliability and minimizing risk of unsupplied demand and pressure deficit, under given economic constraints.

Conventional pervious pavement materials (PPM) consist of cement and aggregate materials and are known for poor durability due to their brittle behavior. Herein, we fabricated polymeric PPMs from durable and abundant polyurethane (PU) to enhance the durability of the material and undertook mechanical and microscopic characterizations. PU-based PPM samples with varying aggregate sizes were produced and the compressive strength and water permeability of each were examined. The pore and tortuosity characteristics of the specimens were analyzed using X-ray micro-computed tomography (micro-CT). Through the micro-CT analysis, the morphological characteristics of the internal structures of PPM were identified and the correlations between the pore size distribution, connectivity, and tortuosity within the specimen were quantitatively analyzed. The microstructures derived from micro-CT were generated as a finite element model and the stress distribution generated inside was numerically determined.