Understanding the effect of staking sequences and identifying the damage occurring within a structure using a structural health monitoring system are the keys to an efficient design of composite-based parts. In this research, a combination of digital image correlation (DIC) and acoustic emission (AE) is used to locate and classify the type of damage depending on the stacking sequence of the laminate during flexural loading. A comparison of the strain field results for unidirectional, cross-ply, and quasi-isotropic laminates was made in a first attempt to discuss their global behavior and to correlate the different damage patterns with the possible failure mechanisms. The damage was then addressed using a comprehensive interpretation of the acoustic emission signatures using the K-means classification of the acoustic events. The development of each damage mechanism was correlated to the applied load and expressed as a function of the loading rate to highlight the effect of the stacking sequence. Finally, the results of DIC and AE were combined to improve the reliability of the damage investigation without limiting the failure mechanism to matrix cracking, interfacial failure, and fiber breakage, as expected by the unsupervised event clustering.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Maintenance of the human chromosomes stability requires a tight regulation of DNA replication to duplicate once and only once the entire genome of a single cell. In mammalians cells, origin activation is controlled in space and time by a cell specific and robust program called replication timing. About 100 000 of potential origins are loaded onto the chromatin at the G1 phase but only 20-30% are selected and active during the replication of a given cell. When the replication fork is slowed down by exogenous or endogenous sources, the cell need to activate more origins to complete the replication on time. Thus, the large choice of origins that can be activated may be a key player in the protection of the genome. The aim of this review is to discuss about the role of these dormant origins as housekeepers of the human genome in response to replicative stress.

High costs for the repair of concrete structures can be prevented if damage at an early stage of degradation is detected and precautionary maintenance measures are applied. To this end, we use numerical wave propagation simulations to identify simulated damage in concrete using convolutional neural networks (CNN). Damage in concrete subjected to compression is modeled at the mesoscale using the discrete element method. Ultrasonic wave propagation simulation on the damaged concrete specimens are performed using the rotated staggered finite-difference grid method. The simulated ultrasonic signals are used to train a CNN based classifier capable of classifying three different damage stages (microcrack initiation, microcrack growth and microcrack coalescence leading to macrocracks). The performance of the classifier is improved by refining the dataset via an analysis of the averaged envelope of the signal. The classifier using the refined dataset has an overall accuracy of 90%.

Critical infrastructures are those that are essential. For this type of infrastructure, it is necessary to implement analytical methodologies that will allow us to quickly obtain the susceptibility or resilience and possible damage generated in extreme precipitation episodes, through a holistic perspective in which the factors linked to hydrological risk intervene. In particular, urban hydraulic infrastructures are analyzed considering the degree of criticality, defined as the number of interactions on the different activities of the population. For this purpose, a hydrological risk analysis methodology is required. This methodology is focused on an integral approach of the system indicators to be analyzed and linked to the hydrological threat. This work proposes to delimit and analyze those factors that involve risk using an analytical expression. This model will estimate the damage to these infrastructures breaking down the factors involved in the risk equation and analyzing their variability according to the intrinsic characteristics linked to them as well as the interaction with external factors.

Water damage is one of the main causes of roads’ deterioration throughout their service life. This effect harms the adhesion and cohesion parameters of the asphalt mix, which leads to a decrease in the structural and functional characteristics of the road surface. This research focuses on studying the water susceptibility of hot mix asphalt mixtures using three different procedures: (1) UNE-EN 12697-12, (2) ASTM D4867, and (3) AASHTO T-283. The tests are carried out on reference mixtures and mixtures modified with polyethylene terephthalate (PET) particles as an additive. The results indicate that the incorporation of 6% PET allows the limits established by the UNE-EN 12697-12 standards to be exceeded, reaching 86% of the tensile strength ratio (TSR). However, for the ASTM D4867 and AASHTO T-283 standards, the results obtained concerning the water susceptibility of the bituminous mixtures were not as satisfactory because the established minimum limits were not reached (< 75%), which indicates that the procedure applied in a test can significantly modify the results of a later application.

Wildfires can be destructive to highway infrastructure. Despite the substantial number of wildfires experienced every year, research on the physical impacts of wildfire on highways has been understudied. This research examines historical and potential future highway physical damage from wildfires. To accomplish our research objectives, we examined three major areas related to physical harm to highways and the consequences of that damage – physical characteristics, roadway impacts, and traffic impacts. These categories were subsequently broken into additional metrics, the first being physical characteristics, which includes length of highway affected and reduced average daily traffic (RADT) impacts during the event. Roadway impacts were broken into the number of trees requiring removal (those that present a danger either standing or fallen), pavement damage (burning asphalt concrete), slope/rock scaling (loose hazard rocks/vegetation), and structural damage (guardrail, signs, and delineators). Traffic impacts included the need for traffic control, road closures required, and reduced annual average daily traffic (RAADT) impacts for the year. The physical characteristics on the three highways researched during the 2020 Oregon Labor Day wildfires (Beachie Creek, Archie Creek, and Holiday Farm) indicated less than 61% of the highways were affected. The highway impacts, which included damage from hazard trees, damage to various structures – guardrail, signs, and delineators as well as bridges, slope/rock scaling damage and pavement destruction – averaged 34% for the three highways, while the three of eight arterial highway routes studied in the Oregon Cascades saw a 21% reduction in AADT. Results from this study can be used not only to assess physical damage to highways from wildfires, but as a baseline for measuring and assessing potential future wildfire highway impacts.

This paper presents an approach to damage identification in beams by modal curvatures based on the use of beamforming algorithms. These processors have been successfully used in acoustics for the last thirty years to solve the inverse problems encountered in source recognition and image reconstruction, based on ultrasonic waves. In addition, beamformers apply to a broader range of problems in which the forward solutions are computable and measurable, especially regarding the field of structural vibrations, where the use of such estimators has not received attention to date. In this paper, modal curvatures will play the role of the replica vectors of the imaging field. By means of numerical studies and experimental tests on a steel beam, we motivate the choice of modal curvatures as observed quantities. Furthermore, we compare the performance of the Bartlett and minimum variance distortionless beamformers (MVDR) with an estimator based on the simple minimization of the difference between model and measured data. The results suggest that the application of the MVDR beamformer is highly effective, especially in cases of slight damage between two sensors. MVDR enabled both damage localization, and quantification.

Seeing atomic configuration of single organic nanoparticles at sub-Å spatial resolution by transmission electron microscopy has been so far prevented by the high sensitivity of soft matter to radiation damage. The difficulty is related to the need to irradiate the particle with a total dose of few electrons/Å2, not compatible with the electron beam density necessary to search the low-contrast nanoparticle, to control its drift, to finely adjust the electro-optical conditions and particle orientation, and to finally acquire an effective atomic resolution image. On the other hand, the capability to study individual pristine nanoparticles, such as proteins, active pharmaceutical ingredients, and polymers, with peculiar sensitivity to the variation of the local structure, defects, and strain, would provide advancements in many fields, including materials science, medicine, biology, and pharmacology. Here we report direct sub-ångström resolution imaging at room temperature of pristine unstained crystalline polymer-based nanoparticles. This result is obtained by combining low-dose in-line electron holography and phase-contrast imaging on state-of-the-art equipment, providing an effective tool for the quantitative sub-angstrom imaging of soft matter.

In rock blasting for mining production, stress waves play a major role in rock fracturing along with explosion gases. Better energy distribution improves fragmentation and safety, lowers production costs, increases productivity, and controls ore losses and dilution. Blast outcomes vary significantly with the choice of the explosive and the properties of the rock mass encountered. This study analyzes the effects of rock mass and explosives properties on the blast outcomes through numerical simulation using data from the case study and later validates the simulation results from the field blast fragmentation. The outcomes suggest that, for a given set of rock properties, the choice of explosive has a major influence on the resulting fragmentation. Strong explosives favor large fracture extents in hard rocks, while less strong explosives offer a better distribution of explosive energy and fractures. The presence of rock structures such as rock con-tacts and joints influences the propagation of stress waves and fractures depending on the structures' material properties, intensity and orientations, and the direction and strength of the stress wave. To achieve effective fragmentation, the blast design should mitigate the effect of variability in the rock mass by ensuring adequate energy distribution within the limits of geo-metrical design.

Phenylketonuria is an inherited metabolic disorder that leads to neurobehavioral dysfunction. The main treatment is a low-phenylalanine diet and/or the cofactor tetrahydrobiopterin. Regular outpatient follow-up care and measurement of the phenylalanine level in the blood are required. We aimed to analyze the economic burden of phenylketonuria on families and the state. The pa-tients with phenylketonuria were divided into three groups according to their treatment: a low-phenylalanine diet group (n= 50), a tetrahydrobiopterin group (n= 44) and a group taking tetra-hydrobiopterin together with the diet (n= 25). A comparative cost analysis was carried out. The annual economic burden to the state was calculated to average €18801±15345 and was lowest in the diet group, then in the tetrahydrobiopterin group and highest in the tetrahydrobiopterin+diet group (p < 0.001). Out-of-pocket costs amounted to €1531±1173 per year, and indirect losses aver-aged €2125±1930 per year for all families. The economic loss was significantly lower in the fami-lies taking tetrahydrobiopterin than in the other groups (p=0.001). The combined use of medical nutrition and BH4 treatments has been shown to increase the economic harm to the state. Reim-bursing low-protein products and increasing the rate of patients eligible for financial allowances may reduce the economic harm to families.

Current understanding of mechanisms of cellular resistance to genotoxic stress is incomplete but is critical for a variety of medical applications. Recent developments in the CRISPR/Cas technologies open new opportunities for targeted interrogation of resistance genes and pathways. In the present work, we used nuclease dead Cas9 constructs to achieve targeted overexpression of endogenous genes encoding two essential subunits of DNA damage sensor complex, XPC and HR23B, in HEK293T cells. Both individual and simultaneous overexpression of the two genes was achieved and the effects on cellular resistance to ionizing radiation and paraquat was examined. Using the fluorometric microculture cytotoxicity assay, we showed that simultaneous, but not separate overexpression of the two genes lead to a 30% increase in survivability. Irradiated cells that overexpressed both XPC and HR23B genes showed higher clonogenic capacity and proliferation rate compared to the irradiated transfection control as revealed by the clonogenic survival assay. Modulation of the gene expression did not affect cell resistance to paraquat. In summary, our results demonstrate a high potential of CRISPR/dCas9-enabled multiplex overexpression of stress-response genes in functionally justified combinations, exemplified here by the XPC-HR23B complex, for achieving an enhanced cellular radioresistance.

Lupus nephritis (LN) is a severe complication of systemic lupus erythematosus (SLE) and is considered one of the leading causes of mortality. Multiple immunological pathways are involved in the pathogenesis of SLE, which makes it imperative to deepen our knowledge about this disease's immunopathological complexity and explore new therapeutic targets. Since an altered redox state contributes to immune system dysregulation, this document briefly addresses the role of oxidative stress (OS), oxidative DNA damage, antioxidant enzymes, mitochondrial function, and mitophagy in SLE and LN. Although adaptive immunity's participation in the development of autoimmunity is undeniable, increasing data emphasize the importance of innate immunity elements, particularly the Toll-like receptors (TLRs) that recognize nucleic acid ligands, in inflammatory and autoimmune diseases. Here, we discuss the intriguing role of TLR7 and TLR9 in developing SLE and LN. Also included are the essential characteristics of conventional treatments and some other novel and little-explored alternatives that offer options to improve renal function in LN.

High temperature (HT) significantly affects the crop physiological traits and reduces the 12 productivity in plants. To increase yields as well as survival of crops under HT, developing heat13 tolerant plants is one of the main targets in crop breeding programs. The present study attempted 14 to investigate the linkage of the heat tolerance between the seedling and the reproductive growth 15 stages of tomato cultivars ’Dafnis‘ and ’Minichal’. This research was undertaken to evaluate heat 16 tolerance under two experimental designs such as screening at seedling stage and screening from 17 reproductive traits in greenhouses. Survival rate and physiological responses in seedlings of 18 tomatoes with 4-5 true leaf were estimated under HT (40 °C, RH 70%, day/night, respectively) and 19 under two control and HT greenhouse conditions (day time 28 °C and 40 °C, respectively). Heat 20 stress significantly affected physiological-chemical (photosynthesis, electrolyte conductivity, 21 proline) and vegetative parameters (plant height, shoot fresh weight, root fresh weight) in all 22 tomatoes seedlings. The finding revealed that regardless of tomato cultivars the photosynthesis, 23 chlorophyll, total proline and electrical conductivity parameters were varied in seedlings during the 24 heat stress period. The heat tolerance rate of tomatoes in the seedling stage might not be associated 25 always with reproductive parameters. HT reduced the fruit parameters likeas fruit weight (31.9%), 26 fruit length (14.1%), fruit diameter (19.1%) and fruit hardness (9.1%) in compared to NT under HT 27 in heat susceptible tomato cultivar ‘Dafnis’, while in heat tolerant cultivar ‘Minichal’ fruit length 28 (7.1%) and fruit diameter (12.1%) was decreased by the affect of HT but on the contrary fruit weight 29 (3.6%) and fruit hardness (8.3%) were increased. In conclusion, screening and selection for tomatoes 30 should be evaluated at the vegetative and reproductive stages with consideration of reproductive 31 parameters.

The paper explores the potential of a low-cost advanced video-based technique for the assessment of structural damage induced to buildings by seismic loading. A low-cost high-speed video camera was utilized for motion magnification (MM) processing of footages of a two-story reinforced concrete frame building subjected to shaking table tests. The damage after seismic loading was estimated by analyzing the dynamic behavior (i.e. in terms of modal parameters) and the structural deformations of the building in the MM videos. The results by MM were compared for method validation to damage assessment obtained by the analyses of conventional accelerometers and high-precision optical markers tracked by a passive 3D motion capture system. Also, 3D laser scanning to obtain an accurate survey of the building geometry before and after the seismic tests was carried out. In particular, accelerometers were also processed and analyzed by using several stationary and non-stationary techniques with the aim to analyze the linear behavior of the undamaged structure and the nonlinear structural behavior during damaging shaking table tests. The proposed MM-based procedure provided accurate estimate of the main modal frequency and the damage location through the analysis of modal shapes, which were confirmed by advanced analyses of accelerometric data.

The dynamic response of structural elements subjected to blast loading is a problem of growing interest in the field of defense and security. In this work, a novel computational tool for the rapid evaluation of the effects of explosions, hereafter referred as SimEx, is presented and discussed. The classical correlations for the reference chemical (1 kg of TNT) and nuclear (106 kg of TNT) explosions, both spherical and hemispherical, are used together with the blast wave scaling laws and the International Standard Atmosphere (ISA) model to compute the dynamic response of Single-Degree-of-Freedom (SDOF) systems subject to blast loading. The underlying simplifications in the analysis of the structural response follow the directives established by UFC 3-340-02 and the Protective Design Center Technical Reports of the US Army Corps of Engineers, which offer useful estimates with a low computational cost, enabling in particular the computation of damage diagrams in the Charge Weight-Standoff distance (CW-S) space for the rapid screening of component (or building) damage levels. SimEx is a computer application based on Matlab and developed by the Fluid Mechanics Research Group at University Carlos III of Madrid (UC3M), which has been successfully used for both teaching and research purposes in the Degree in Security Engineering, taught to the future Guardia Civil officers at the Spanish University Center of the Civil Guard (CUGC). This dual use has allowed the development of the application well beyond its initially objective, testing on one hand the implemented capacities by undergraduate cadets with end-user profile, and implementing new functionalities and utilities by Masters and PhD students. With this experience, the application has been continuously growing since its initial inception in 2014 both at a visual and a functional level, including new effects in the propagation of the blast waves, such as clearing and confinement, and incorporating new calculation assistants, such as those for the thermochemical analysis of explosive mixtures; crater formation; fragment mass distributions, ejection speeds and ballistic trajectories; and the statistical evaluation of damage to people due to overpressure, body projection, and fragment injuries.

Biocontrol strategies are gaining tremendous attention with the growing awareness of the irreparable harm caused by the continuous use of synthetic pesticides. This study examines the proteolytic and chitinolytic activities of Bacillus velezensis CE 100 and its termiticidal effect through cuticle degradation. The proteolytic and chitinolytic activities of B. velezensis CE 100 systematically increased with cell growth to the respective peak of 68.3, and 128.3 units/mL after seventh days of inoculation, corresponding with the highest cell growth of 16 x 107 colony forming units (CFU)/mL. The in vitro termiticidal assay showed that B. velezensis CE 100 caused a rapid and high rate of termite mortality with the median lethal time (LT50) of &gt; 1h, and the highest mortality rate of 91.1% and 92.2% recorded at 11h and 12h in the bacterial broth culture and crude enzyme fraction, respectively. In addition to broken setae and deformed sockets, termites treated with the bacterial broth culture exhibited degraded epicuticles, while the crude enzyme fraction caused severe disintegration of both the epicuticle and endocuticle. These results indicate a tremendously higher prospect of B. velezensis CE 100 in the biological control of subterranean termites compared to the previously used entomopathogenic bacteria.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

Various wood fibres, including pine and flax, are used in wood–plastic composites (WPCs). This paper studies the effect of the lignin content on the morphological and thermal degradation and damage due to the ultraviolet (UV) aging of polypropylene/flax (PP-flax) and polypropylene/pine (PP-pine) fibres composites. Flax and pine fibres exhibited distinct densities of 1.51 and 1.47 g/cm³, respectively, potentially influenced by growth factors and varying compositions of light substances, such as hemicellulose, lignin, and impurities. The thermal decomposition mass loss increased proportionally with the percentage of lignin in the fibre. From 238°C to 390°C, the pine fibre exhibited a 72% mass loss compared to flax fibre, which showed a 54% mass loss, owing to the higher lignin content in pine fibres. Based on differential scanning calorimetry (DSC), the fibre composition affected the material melting temperature. Moreover, DSC curves revealed a higher degree of crystallinity in the case of the PP-flax biocomposite (12%) compared to pure polypropylene (9%) and PP-pine (6%). This result can be attributed to the high content of crystalline components in flax fibres, such as cellulose. Acoustic emissions analysis confirmed that the high lignin content delays degradation and mitigates the appearance of microcracks on the surface of the PP-pine biocomposite. Overall, the study provides valuable data for understanding the UV degradation phenomenon in biocomposites and highlights the influence of fibre composition on material performance.

A tritium resistant coating on the surface of materials is one of the main methods to reduce tritium permeability. In actual operating processes, mechanical damage such as spalling and scratches will occur on the surface of tritium resistant coatings. These mechanical damages will affect the hydrogen permeability resistance of the coatings. It is an important engineering problem that evaluate the effect of these damage on the tritium resistance of the coating. In this experiment, the mechanical damage of FeAl/Al2O3 tritium resistant coating on 316L stainless steel was simulated by scratching, debonding and thermal shock, and the gas hydrogen isotope permeation (GDP) test was carried out. The influence of mechanical damage degree on the tritium permeation behaviour of the coating was evaluated and discussed.

Background: Breast cancer incidence and mortality exhibit a rising trend globally among both premenopausal and postmenopausal women suggesting that there are serious errors in our preventive and therapeutic measures.Purpose: Providing a series of valuable, but misunderstood inventions highlighting the role of increasing estrogen signaling in prevention and therapy of breast cancer instead of its inhibition. Results: 1. Breast cells and breast cancer cells with germline BRCA1/2 mutations similarly show defect in liganded estrogen receptor (ER) signaling demonstrating its role in genomic instability and cancer initiation. 2. In breast cancers, the increased expression of certain receptor family is an effort for self directed improvement of genomic defects, while the weakness or loss of receptors indicates a defect requiring medical repair. 3. ER overexpression in breast cancer cells is capable of strengthening estrogen signaling and DNA repair, while in ER negative tumors, HER2 overexpression tries to upregulate unliganded ER activation and genome stabilization. 4. ER positive breast cancers responsive to endocrine therapy may show a compensatory ER overexpression resulting in a transient tumor response. Breast tumors, non responsive to endocrine therapy, show HER2 overexpression for compensation the complete blockade of liganded ER activation. 5. In breast tumors, somatic mutations serve upregulation of liganded or unliganded activation of ERs helping genome stabilization and apoptotic death. 6. The dynamic communication between breast cancer and its microenvironment is a wonderful collaboration among molecular players fighting for genomic repair and apoptosis in the tumor. 7. In breast cancers, there is no resistance to genotoxic or immune blocker therapies, but rather the non responsive tumor cells exhausted all compensatory possibilities against therapeutic damages. Conclusion: Understanding the behavior and ambition of breast cancer cells may achieve a turn in therapy via applying a supportive care instead of genotoxic measures.

Nigella sativa (NS) is an effective medicinal plant possessing noteworthy antioxidant property. In NS, there are more than hundred phyto-chemicals reported, out of which thymoquinone is the utmost active phyto-constituent having sturdy antioxidative property. Thymoquinone is a cyclicdione, when reacts with sodium azide, converts into α-azido ketones i.e its analogs which are handy with extensive range of reactions. Sodium azide induces stress in plants thereby, modulating the antioxidant system. The present investigation was planned to elucidate the effect of sodium azide at different concentrations (5µM, 10µM, 20µM, 50µM, 100µM and 200µM) on its secondary metabolites (mainly thymoquinone) in NS callus culture extract (NSE). The results showed sodium azide effect on thymoquinone content and a concentration dependent boost in antioxidant property. It was also observed that thymoquinone content and percent yield (analyzed by RP-HPLC; Reverse Phase- High Performance Liquid Chromatography) were minimum (0.033±0.006% and 0.420±0.045%, respectively) at 200 µM sodium azide used. Whereas, antioxidant activity (analyzed by DPPH; 2, 2-diphenyl-1-picrylhydrazyl) was found to be maximum (3.873±0.402%) at same dose. Further, analysis was done for inhibition of oxidative DNA damage at different concentrations of sodium azide on NSE, maximum inhibition of DNA damage (0.243±0.017%) was found at 200 µM concentration of sodium azide. When correlated, strong positive correlation was observed between percent yield and percent thymoquinone, antioxidant property and inhibition of DNA damage. Whereas, strong negative correlation was observed between percent yield and antioxidant property, percent thymoquinone and antioxidant property, percent thymoquinone and inhibition of DNA damage. The findings evidently point out that the content of thymoquinone, antioxidant property and inhibition of DNA damage was affected by sodium azide.

The coffee leaf miner Leucoptera coffeella (Guérin-Mèneville & Perrottet), is a key pest in coffee producing countries. During their development, the larvae feed on the palisade parenchyma of the leaves forming mines. As a result, the photosynthetic area of the plant decreases, affecting coffee production. Despite the severity of the damage caused by coffee leaf miner (CLM), morphological aspects of the larval development and the adult genitalia remain unknown. It is important to identify more susceptible targets to an efficient and narrow control by natural or synthetic approaches, relies on determining the larval instars. Equally important is the sexing of the adult, in experiments aiming efficient ways to control CLM, as the study of pheromone-based control methods. This work presents the first morphological description of the four larval instars and the adult genitalia of L. coffeella. In each larval instar, we measured the Mean ± SD (mm) of the cephalic capsules (1^st 0,14±0,03; 2^nd 0,25±0,04; 3^rd 0,32±0,03; 4^th 0,42±0,03) and observed the following morphological details: primary setae, prolegs, crochets and ecdysial line of the cephalic capsule. In the adults, we observed the sexual structures present in both genitalia: male - bulbus ejaculatorius, valva, anellus, gnathos and aedeagus and female - ovipositor, sclerite and corpus bursae. The dissection of the adult specimens confirmed that the external morphology corresponds to the correct sex attribution in CLM adults. These results may support innovative and improved control strategies for CLM Integrated Pest Management (IPM).

Urban trees are often more sun- and wind-exposed than their forest-grown counterparts. These environmental differences can impact how many species grow – impacting trunk taper, crown spread, branch architecture, and other aspects of tree form. Given these differences, windthrow models derived from traditional forest production data sources may not be appropriate for urban forest management. Additionally, visual abnormalities historically labeled as “defects” in timber production may not have a significant impact on tree failure potential. In this study, we look at urban tree failures associated with Hurricane Irma in Tampa, Florida, USA. We used spatial analysis to determine if patterns of failure existed among our inventoried trees. We also looked at risk assessment data to determine which visual defects were the most common and the most likely to be associated with branch or whole-tree failure. Results indicate that there was no spatial pattern associated with the observed tree failures – trees failed or withstood the storm as individuals. While some defects like decay and dead wood were associated with increased tree failure, other defects like weak branch unions and poor branch architecture were less problematic.

Radical oxygen species formed in human tissue cells by many endogenous and exogenous pathways, cause extensive oxidative damage, which has been linked to various human diseases. This review paper provides an overview of lipid peroxidation and focuses on the free-radicals initiated processes of LDL oxidative modification and DNA oxidative damage, which are widely associated to the initiation and development of atherosclerosis and carcinogenesis, respectively. The article subsequently provides an overview of the recent human trials or even in vitro investigations on the potential of natural antioxidant compounds (such as carotenoids, vitamins C and E) to monitor LDL and DNA oxidative changes.

Appropriate diagnosis, treatment and care contributes to better service engagement, improvements to wellbeing, cost savings, reductions in morbidity and mortality for people with Alcohol Related Brain Damage. In the North-East of England large amounts of alcohol are consumed, reflected in the number of alcohol-related deaths in the region. However, the pathway for people with Alcohol Related Brain Damage to receipt of diagnosis, treatment and care is unknown and could be unwittingly influenced by stigma. Qualitative in-depth semi-structured interviews were completed with 25 health and social care professionals from organisations involved with people with Alcohol Related Brain Damage recruited via snowball-sampling. Interviews were recorded, transcribed verbatim, coded, and analysed. People with Alcohol Related Brain Damage were stigmatised both by society and professionals which inhibited entry into services therefore Alcohol Related Brain Damage remained underdiagnosed and misdiagnosed. There was no dedicated service but silos with revolving doors and underfunded generic care with long waiting lists typically excluding those with alcohol or neurological problems. Professionals need to be challenged on the assumption that Alcohol Related Brain Damage is self-inflicted via training aimed at challenging unconscious bias. Reducing stigmatising processes associated with Alcohol Related Brain Damage could counteract professionals’ reluctance to provide care.

With more and more transportation tunnels have been and will be constructed in loess areas in Northwest China with high earthquake potential, the overall stability of portal section under earthquakes actions and the related aseismic countermeasures attracted the attentions from both the scholars and engineers, especially the tunnels in the upper slope connecting the high bridges crossing rivers or valleys. In order to study the dynamic response characteristics and damage evolution of steep loess slope with a tunnel under the earthquake actions, a large-scale shaking table tests were performed on steep loess slope with a tunnel. Wenchuan-tangyu (WT) wave and El Centro (El) wave records were applied on the model to investigate the displacement response and acceleration response of loess slope with a tunnel under the horizontal (X) and the combined action of horizontal and vertical (X-Z) seismic loads, respectively. In particular, three-dimensional non-contact optical measurement techniques were used to obtain the slope surface displacements. The results showed that the main deformation pattern of the slope was horizontal movement and settlement when the seismic wave input was in the X and X-Z directions, respectively. However, the X direction seismic wave had a greater impact on the deformation of the slope, and the tunnel portal slope was destroyed under the action of a large horizontal seismic acceleration finally. Slope failure ahead of a tunnel could be divided into four stages, i.e. elastic deformation stage, plastic deformation accumulation stage, local failure stage, and overall failure stage. The peak ground displacement of X direction (PGDX) and peak ground displacement of Z direction (PGDZ) of the slope surface increased with the increasing of the input peak ground acceleration (PGA) when the input wave was same waveform and same direction. The existence of the tunnel had a great influence on the PGA and the PGA amplification factor (PGAAF) of the soil mass surrounding it. This was because the seismic waves encounter a tunnel surface with clear differences in the physical properties of the medium during their propagation in the slope, thereby forming a strong reflection and refraction effect, and the amplitude changed significantly. Numerical simulation results were basically consistent with the experimental results.

Damage assessment is one of the most crucial issues for bridge engineers, especially for existing steel bridges. Among several methodologies, the vibration measurement test is a typical approach in which the natural frequency variation of the structure is monitored to detect the existence of damage. However, locating and quantifying the damage is still a big challenge. In this regard, the artificial intelligence (AI)-based approach seems a potential way to accomplish those obstacles. This study deploys a comprehensive campaign to determine all dynamic parameters of a pre-damage steel truss bridge structure. Based on the results of mode shape, natural frequency, and damping ratio, a finite element model (FEM) is created and keeps updating. The artificial intelligence network's input data will be analyzed and evaluation from damage cases. The trained artificial neural network model will be curated and evaluated to confirm the approach's feasibility. During the actual operational stage of the steel truss bridge, this damage assessment system is showing good performance in terms of monitoring the structural behavior of the bridge under some unexpected accidents.

(Background) Phytotoxicity refers to the capacity of chemical substances or environmental factors to have a negative impact on plants. This is a crucial issue in both the context of crop cultivation and environmental protection. (Material and Methods) The research results were based on a 3-year field experiment conducted at the experimental station in Jadwisin (52°28′ N, 21°02′ E) on loamy soil. The experiment was set up using a randomized sub-block design in a split-split-plot arrangement, with three replications. The first-order factor consisted of potato cultivars, while the second-order factors were weed control methods: 1) Control – without protection; 2) mechanical weed control, extensive mechanical treatments to close rows; 3) Sencor 70 WG – pre-emergence (PRE) of potatoes; 4) Sencor 70 WG + Titus 25 WG + Trend 90 EC – PRE of potatoes; 5) Sencor 70 WG – post-emergence (POST) of potatoes; 6) Sencor 70 WG + Titus 25 WG + Trend 90 EC – POST of potatoes; 7) Sencor 70 WG + Fusilade Forte 150 EC – POST of potatoes; 8) Sencor 70 WG + Apyros 75 WG + Atpolan 80 SC – POST of potatoes. The phytotoxic effects of herbicides on potato plants and weeds were assessed every 7 days, starting from the date when the first signs of damage appeared, until they stabilized or disappeared. (Results:) Phytotoxic damage to potato and weed plants were caused by the chemical weed control methods used. The response of potato plants to herbicides was significantly related to the genetic traits of the cultivars and meteorological conditions in the years of research. (Conclusion:) Phytotoxicity is an important aspect in both agriculture and environmental protection. Research on its mechanisms and impact will enable the development of effective plant protection strategies and the preservation of ecosystem balance.

This randomized trial compared pea protein, whey protein, and water-only supplementation on muscle damage, inflammation, delayed onset of muscle soreness (DOMS), and physical fitness test performance during a 5-day period after a 90-minute eccentric exercise bout in non-athletic, non-obese males (n=92, ages 18-55 years). The two protein sources (0.9 g protein/kg divided into three doses/day) were administered under double blind procedures. The eccentric exercise protocol induced significant muscle damage and soreness, and reduced bench press and 30-second Wingate performance. Whey protein supplementation significantly attenuated post-exercise blood levels for biomarkers of muscle damage compared to water-only, with large effect sizes for creatine kinase and myoglobin during the 4th and 5th days of recovery (Cohen's d &gt;0.80); pea protein versus water supplementation had an intermediate, non-significant effect (Cohen's d &lt;0.50); and no significant differences between whey and pea protein were found. Whey and pea protein compared to water supplementation had no significant effects on post-exercise DOMS and the fitness tests. In conclusion, high intake of whey protein for 5 days after intensive eccentric exercise mitigated efflux of muscle damage biomarkers, with intake of pea protein having an intermediate effect in part due to the 24% lower leucine amino acid content.

With forty years of developments, bio-macromolecule cryo-electron microscopy has met its revolution of resolution and is playing a very important role in structural biology study. According to different specimen states, cryo-electron microscopy (cryo-EM) involves three specific techniques, single particle analysis (SPA), electron tomography and sub-tomogram averaging, and electron diffraction. All these three techniques have not realized their full potentials of solving structures of bio-macromolecules and therefore need to be developed in the future. In this review, the current existing bottlenecks of cryo-EM SPA are discussed with theoretical analysis, which includes air-water interface during specimen cryo-vitrification, bio-macromolecular conformational heterogeneity, focus gradient within thick specimen, and electron radiation damage. Besides, potential solutions of these bottlenecks are proposed and discussed, which are worthy of further investigations in the future.

To achieve rapid post-earthquake repair of self-centering ribbed floor flat beam frame structures, a ductile hybrid joint consisting of dog bone weakened energy dissipating steel bars connected to the upper and lower column sections through high-strength threads based on the damage control design concept is proposed. By moving the ductile energy dissipating zone out to the locally weakened section of the energy dissipating steel bars and the locally unbonded prestressed steel bars in the core area, the residual deformation was limited and the seismic performance was improved. Based on the working principle of hybrid joints, low cycle loading tests were conducted on two joint specimens to analyze the influence of lateral prestress on the seismic performance of the hybrid joints. Numerical modeling methods were used to compare the position of the energy-consuming steel bars in the composite layer and the friction performance of joints. The research results indicated that the hybrid joint had stable load-bearing, deformation, and energy dissipation capabilities, with damage primarily concentrated on the energy-consuming steel bars. Even at an inter-story displacement angle of 5.5%, the upper and lower column segments remained elastic. After unloading, the connection seam at the joint was closed, and the self-centering performance was good. When the inter-story displacement angle reached 5.5%, the lateral prestress increased from 150 kN to 250 kN, the ultimate bearing capacity of the joint increased by 16.3%, and the cumulative energy consumption increased by 30.0%. The influence of the friction coefficient of the joint surface on the structural performance was set at a threshold of 0.7. When it was less than the threshold, the ultimate bearing capacity and initial stiffness of the joint increased with an increase in the friction coefficient. After reaching the threshold, the increase in the ultimate bearing capacity of the joint slowed down, and the rate of stiffness degradation gradually accelerated. This joint had excellent seismic performance and can also achieve post-earthquake repair of structures.

Background: KDM5 enzymes are H3K4 specific histone demethylases involved in transcriptional regulation and DNA repair. These proteins are over-expressed in different kinds of cancer, including breast, prostate and bladder carcinoma, with positive effects on cancer proliferation and chemo-resistance. For these reasons, these enzymes are potential therapeutic cancer targets. Methods: In the present study, we analyzed the effects of three different inhibitors of KDM5 enzymes in MCF-7 breast cancer cells over-expressing JARID1B. In particular we tested H3K4 demethylation (western blot); target gene transcription (RNAseq and real time PCR); radio-sensitivity (citoxicity and clonogenic assays) and damage accumulation (kinetics of H2AX phosphorylation). Results: we show that two compounds with completely different chemical structure can selectively inhibit KDM5 enzymes and that both compounds are capable of increasing sensitivity of breast cancer cells to ionizing radiation and H2AX phosphorylation. Conclusions: These findings confirm the involvement of H3K4 specific demethylases in DNA damage signaling and repair and suggest new strategies for the therapeutic use of their inhibitors.

The insufficient toughness of concrete can lead to the occurrence of crack expansion, ultimately resulting in a decline in the physical and mechanical properties such as bearing capacity and deformation characteristics of structural components. In severe cases, this may lead to brittle failure, where the entire structure and system fail suddenly without significant deformation after being stressed. Additionally, during the process of shear and bending failure of reinforced concrete beams, the cracks generated on the side of the beam are mostly I-II composite cracks. Considering the material nonlinearity and geometric irregularity of reinforced concrete, it is of great significance to study the dynamic evolution law of crack expansion in reinforced concrete members. Based on experimental data, this paper aims to utilize the nonlinear finite element simulation software Abaqus to conduct finite element simulations of crack expansion in simple supported reinforced concrete beams. By accurately controlling the constitutive curves of concrete and reinforcement materials, the design of seismic performance of structural members can be enhanced, thereby making essential contributions to the preliminary analysis of actual crack control engineering. The nonlinear finite element results indicate that the joint cracks of the frame with the floor slab primarily manifest as flexural cracks, with the concrete damage degree of the floor slab being higher than that of the beam. This finding underscores the importance of considering the behavior of concrete and reinforcement materials in designing for seismic performance and crack control in actual engineering applications.

Galangin(Gal) is a natural active flavonoid compound separated from the roots and rhizomes of Alpinia ofcinarum Hance. Modern pharmacological studies have shown that Gal has a variety of biological activities such as anti-tumor, anti-fungal, anti-bacterial, anti-inflammatory, anti-ischemic stroke, suppressing vitiligo and Alzheimer’s disease, etc. The purpose of this research was to prepare a galangin self-microemulsion drug delivery system (Gal-SMEDDS) and compare its anti-oxidant activity and pharmacokinetics with free Gal.The average particle size of the prepared Gal-SMEDDS was approximately 21.33 nm, the polydispersity index was 0.096, the zeta potential was -4.09 mV, and the entrapment efficiency was 96.74%. Compared with free Gal, the release of Gal-SMEDDS was improved in vitro release experiment. Cell experiments showed that Gal had obvious anti-oxidation effect, and the effect of Gal-SMEDDS was better than that of free Gal. In vivo pharmacokinetic experiments showed that the pharmacokinetic parameters of Gal-SMEDDS were better than that of free Gal, which indicated that the self-microemulsion drug delivery system(SMEDDS) effectively increases the oral bioavailability of Gal and alters its pharmacokinetic parameters, such that it may be effective in the treatment of anti-oxidant.

The Siret River crosses NE Romania from the north to the south and it discharges into the Danube, near the city of Galati. During the period, 17^th June - 10^th July 2010, significant amounts of precipitations in the mountainous basin of Siret were recorded. The floods comprised two periods with four bimodal cycles and they were counted among the strongest on the Romanian territory. The exceptional floods occurred in the rivers of Siret, Suceava, Moldova, Bistrita, Trotus and so on. The most important compound flood wave was determined by the precipitations which fell within the period, 29^th June to 1^st July 2010, when significant amounts of rain were recorded, sometimes, exceeding 80 mm. The high discharges on the Bistrita River – downstream from the Bicaz Reservoir – were controlled by complex hydro technical works. The maximum discharge for the year 2010 summer floods was recorded at Dragesti hydrometric station: 2,884 m³/s (historic discharge) compared to the preceding historic discharge of the year 2008 (2,850 m³/s). The effects of floods were strongest in the counties of Suceava, Neamt, and Bacau. The floods on the main course of the Siret River were analyzed in correlation with the tributaries within the mountainous sector.

The saltmarsh plant Halimione portulacoides was shortly exposed to realistic levels of inorganic mercury (iHg), aiming to investigate adaptative processes of the roots and leaves regarding re-dox homeostasis, physiology, and Hg accumulation. Plants were collected at a contaminated (CONT) and a reference (REF) site, addressing the interference of contamination background. The influence of major abiotic variables (i.e., temperature and light) was also examined. Total Hg lev-els, antioxidant enzymes, lipid peroxidation (LPO), and photosynthetic activity were analyzed after 2 and 4 hours of exposure. Accumulation of iHg in the roots was noticed poorly, and no translocation to stems and leaves was found, but plants from CONT seemed more prone to iHg uptake (in winter). Despite that, antioxidant modulation in roots and leaves was found, disclos-ing, in winter, higher thresholds for the induction of enzymatic antioxidants in CONT leaves compared to REF, denoting that the former are better prepared to cope with iHg redox pressure. Consistently, CONT leaves exposed to iHg had remarkably lower LPO levels. Exposure did not impair the photosynthetic activity, pinpointing H. portulacoides ability to cope with iHg toxicity under a very short-term exposure. Biochemical changes were noticed before enhancements in ac-cumulation, reinforcing the relevance of these responses in precociously signaling iHg toxicity.

This paper investigates the effects that rain drop erosion has on the integrity of wind turbine materials. This research involves analysis of impact models and theoretical equations to simulate the impact phenomena when a raindrop collides with a wind turbine blade at high speed. Impact phenomena that occur when a raindrop impacts with a wind turbine blade were evaluated. Additionally, the use of various types of software was considered to simulate this impact event. The model results of the raindrop impact with respect to a comparison of the governing equations and impact behaviour are addressed. Future work is outlined including adding variables to the erosion modelling algorithms.

In recent years in Bangladesh, there has been regular cyclonic event, flooding and erratic pre-monsoons precipitation that has hampered production greatly and forced Bangladesh to import salt from abroad to manage market deficiency. There is much uncertainty about the effects of climate change on the frequency and intensity of small-scale, sudden onset weather phenomena such as heavy rainfall and subsequent loss and damage (L&D). But, several studies indicate that an obvious strong relationship exists between irregular rainfall and associated L&D. Nowadays, severe changing rainfall patterns are observed in Bangladesh, which is rapid-onset in nature, but low exposed in terms of response. The current study explored a ‘double-exposed’ burden combined of both climatic (e.g., uneven rainfall) and non-climatic governance factors (e.g., imperfect trade policy, the absence of risk transfer mechanisms) which are hindering salt production and pushing the country from the aspiration of salt exporting to the net buyer. This chapter mainly assesses the impacts of L&D due to climatic events that are causing overwhelming effects on the well-being of marginal salt farmers at Kutubdia Upazila of Bangladesh. Data were mainly collected through Participatory Vulnerability Analysis (PVA), Key informant interviews (KII), and Sample Surveys (SS). This study would provide insights for improved disaster management policy and an appropriate adaptive measure to address such extreme events as well as to initiate a further study for understanding the nexus of ‘nature and market’ in building resilience among the marginal salt farmers.

The horse chestnut leaf miner Cameraria ohridella (Lepidoptera: Gracillariidae) is an invasive pest of horse chestnut and has spread through Europe since 1985. The horse chestnut leaf blotch Guignardia aesculi (Botryosphaeriales: Botryosphaeriaceae) is a fungal disease that also seriously damages horse chestnut trees in Europe. The interaction between the leaf miner and the fungus has not yet been sufficiently described. Therefore, the aim of the present study was to assess leaf damage inflicted to horse chestnut by both C. ohridella and G. aesculi during the vegetation season and to model their interaction. The damage to leaf area was measured monthly from May to September 2013 in České Budějovice, the Czech Republic. A simple phenomenological model describing the expected dynamics of the two species was developed. The study revealed a significant effect of sampling site and sampling period on the damage caused by both the pest and the fungus. The mathematical model indicates that infestation by C. ohridella is more affected by G. aesculi than vice versa. The possible mechanisms affecting the relationship between G. aesculi and C. ohridella are discussed.

This paper investigates the integration of SHM within the frame of Industry 4.0 technologies, highlighting the potential for intelligent infrastructure management through the utilization of Big Data analytics, Machine Learning, and the Internet of Things (IoT). The study also presents a success case focused on a novel SHM methodology for detecting and locating damages in metallic aircraft structures, employing dimensional reduction techniques such as Principal Component Analysis (PCA). By analyzing strain data collected from a network of sensors and comparing it to a baseline pristine condition, the methodology aims to identify subtle changes in local strain distribution indicative of damage. Through extensive Finite Element Analysis (FEA) simulations and a PCA contribution analysis, the research explores the influence of various factors on damage detection, including sensor placement, noise levels, and damage size and type. The findings demonstrate the effectiveness of the proposed methodology in detecting cracks and holes as small as 2mm in length, showcasing the potential for early damage identification and targeted interventions in diverse sectors such as aerospace, civil engineering, and manufacturing. Ultimately, this paper underscores the synergistic relationship between SHM and Industry 4.0, paving the way for a future of intelligent, resilient, and sustainable infrastructure.

To evaluate whether the extent of cardiac damage in severe aortic stenosis (AS) might be associated with the occurrence of conduction system disorders after TAVI. A total of 153 symptomatic patients with severe AS who had a TAVI were categorized before the procedure according to the extent of cardiac damage: stage 1 (13.5%): no or LV damage; stage 2 (58.8%): left atrial/mitral valve damage, atrial fibrillation (AF); stage 3 (27.7%): low-flow state, pulmonary vasculature/tricuspid valve/RV damage. After TAVI, 34% of patients exhibited LBBB and 10% high-degree atrioventricular block (HD-AVB). No patient in group 1 developed HD-AVD whereas new LBBB was frequent in groups 2 and 3. Twenty-one patients presented with resolutive paroxysmal AF with a higher rate for each group increment (group 1: n=0, 0%; group 2: n=11,15.7%; group 3: n=10, 30.3%) (p = 0.012). Patients in group 3 had the higher rate of permanent pacemaker implantation (PPMI) (group 1: n=1, 6.3%; group 2: n=7,10%; group 3: n=9, 27.3%) (p=0.012). No patient in group 1 died during the hospital stay. In conclusion, cardiac damage staging of AS might help identify patients at higher risk of conduction disorders and PPMI requirement after TAVI.

The use of fluoride (F^-) for decreasing the prevalence and incidence of tooth decay was the greatest worldwide preventive public health measure of the 20th century. There have been controversial reports about the benefits of the use of F^-, because in small amounts it helps prevent dental caries, but in high concentrations it can be potentially toxic and harmful to dental and systemic health. Since the mid-20th century, F^- has been studied by toxicologists, looking at its deleterious effects in human populations. During the last decade, the interest on the undesirable effects has resurfaced because of the knowledge that it interacts with the cellular system, even in low doses, with a very small safety margin. Acute ingestion of toxic amounts of fluoride can cause corrosive gastric mucosa injury. Also respiratory effects such as bleeding, pulmonary edema, tracheostomy and shortness of breath, have been observed in individuals who inhale hydrogen fluoride. Some researchers had shown that F^- is an oxidizing agent and a well-known reversible enzymatic inhibitor that interferes with the enzyme activity of at least 80 proteins, can altered the intracellular redox equilibrium, lipid peroxidation, as well as, alteration in the gene expression and apoptosis induction. The primary purpose of this review is to examine findings of the action of inorganic F^-, and an overview of hard and soft tissue disturbances, known as fluorosis. The goal of this review is to enhance understanding of the mechanisms by which F^- affects cells with an emphasis on human tissue-specific events.

This research is aimed to develop the method for damage degree evaluation in metals and alloys during their deformation and destruction based on acoustic emission (AE) technique. Experimental studies were carried out on tensile specimens of high-strength steel with simultaneous registration of AE signals in tested material. It was shown that the time-dependent AE primary parameters, such as the AE signal maximum amplitudes and AE activity, do not have a clear relationship with the material damage degree. This fact makes it difficult to use standard methods for assessing the damage degree of acoustic signal sources, including defects. It was proposed to use the Kolmogorov-Smirnov criterion to differ the processes of metal plastic deformation and crack propagation during the rupture. The possibility of estimating the material damage degree by high-energy AE hits share was shown. Besides, a particular expression was obtained for evaluating the damage degree for the material under study.

The successive waves of the Covid-19 pandemic are driven by SARS-CoV-2 variants that reached critical detection levels in different parts of the world. But how evolved the Wuhan virus since its detection in December 2019 into the Alpha (B.1.1.7), Beta (B.1.351), Gamma (P.1), Delta (B.1.617.2) and Omicron (B.1.1.529) variants of concern? This is a story of mice and men, of up to 1,000,000 infected cells in one person, where each cell produces between 10⁵ and 10⁶ viral RNAs, of immune-compromised patients, the digestive tract and viral recombination.

This article proposes a monitoring system that allows to track transitions between different stages in the berry harvesting process (berry picking, waiting for transport, transport, and arrival to the packing) solely using information from temperature and vibration sensors located in the basket. The monitoring system assumes a characterization of the process based on Hidden Markov Models and uses the Viterbi algorithm to perform inference and estimate the most likely state trajectory. The obtained state trajectory estimate is then used to compute a potential damage indicator in real-time. The proposed methodology does not require information about the weight of the basket to identify each of the different stages, which makes it effective and more efficient than other alternatives available in the industry.

In a concrete beam initially crack is generated at the tension side under the effect of flexure, shear and torsional loadings. Accordingly, these weak concrete members require repair and/or strengthening to increase or restore their internal load capacity. In the current experimental and numerical investigations on concrete beam having different width to depth ratio of notch on its ultimate flexural load under one-point loading was considered. Further, the flexural behavior performance of notch concrete beam repaired with the three repair materials cement mortar, bacterial mortar and adhesive was also examined. Consequently, a comparative study is imple-mented between the experimental and numerical results. Concrete Damage plasticity (CDP) model was used for finite element numerical analysis of beam. The differences in numerical and experimental measured results ranges from 0.65 - 22.20 % for the ultimate load carrying capacity. As the notch size increases the ultimate load carrying capacity of beam was reduced. Addition-ally, linear regression model is used to predict the ultimate load values at an interval of 5 mm notch width up to maximum width of notch 100 mm. It can be observed that the ultimate load capacity for repaired beam is increased as compared to the notch beam for all the three repairing materials under consideration. The maximum ultimate load was increased in case of notch beam repaired using adhesive. As compared to the cement mortar the performance of the bacterial mortar in terms of the ultimate load was more. The bacterial mortar is found more sustainable and more durable as a repair material for the concrete structures.

Mining can impact the environment, biodiversity and human health through direct and indirect practices. This study investigated the effects of gold mining on Gerbillus nanus, pointing to organ dysfunction and redox imbalance. Soil samples, Lycium shawii and G. nanus were collected from a site near a mining planet and a control site. Soil and L. shawii samples from the mining site showed a significant increase cadmium (Cd), cupper (Cu), mercury (Hg), arsenic (As), zinc (Zn), lead (Pb) and vanadium (V). Hepatic, renal and pulmonary Cd, Pb, Hg, Zn, Cu, Fe, As and V concentrations were increased significantly in G. nanus at the mining site. Markers of liver and kidney function were elevated in serum, and several histological manifestations were demonstrated in liver, kidney and lung of G. nanus at the mining site. Malondialdehyde and nitric oxide were increased, and glutathione and antioxidant enzyme were declined in the liver and kidney of G. nanus. In conclusion, mining practices triggered tissue damage and oxidative stress in G. nanus living close to the mining site. These findings can represent the scientific basis for evaluating the environmental and health impact of mining in the on the nearby communities.

To gain insight into riser motions and associated fatigue damage due to vortex-induced vibration (VIV), data loggers such as strain sensors and/or accelerometers are sometimes deployed on risers to monitor their motion in different current velocity conditions. Accurate reconstruction of the riser response and empirical estimation of fatigue damage rates over the entire riser length using measurements from a limited number of sensors can help in efficient utilization of the costly measurements recorded. Several different empirical procedures are described here for analysis of the VIV response of a long flexible cylinder subjected to uniform and sheared current profiles. The methods include weighted waveform analysis (WWA), proper orthogonal decomposition (POD), modal phase reconstruction (MPR), a modified WWA procedure, and a hybrid method which combines MPR and the modified WWA method. Fatigue damage rates estimated using these different empirical methods are compared and cross-validated against measurements. Detailed formulations for each method are presented and discussed with examples. Results suggest that all the empirical methods, despite different underlying assumptions in each of them, can be employed to estimate fatigue damage rates quite well from limited strain measurements.

Lightning strike can cause a considerable damage in aircraft parts made from semiconducting materials such as Carbon Fiber Reinforced Plastics (CFRPs). Therefore, in recent years, the lightning strike phenomenon has attracted the interest of the academic community and the aircraft industry. Until now, the problem has been addressed mainly experimentally, while the reported numerical works are very limited. In the present work, a coupled electro-thermal FE model has been developed using the ANSYS commercial FE code to simulate the lightning strike damage in unidirectional CFRP laminates due to the Joule heat flux phenomenon. The model is based on the SOLID69 thermoelectric element and applies a non-linear, time-transient analysis. The main input to the model is the thermal-electrical properties of the composite material which vary with temperature. Using the model, a parametric study on the effect of mesh density and peak intensity on the thermal damage has been performed. Three electrical lightning strikes of low (10 kA), medium (30 kA) and high peak intensity (40 kA) have been applied according to the SAE ARP 5412 standard. The electro-thermal model has been validated against a numerical model from the literature. The numerical results reveal that the increase of peak intensity leads to the increase of the area and penetration depth of matrix thermal damage (pyrolysis) as well as to the increase of the area of fiber damage (deterioration and ablation). Through progressive damage modeling, the residual tensile strength of the CFRP plate after being subjected to lightning strike of different peak intensity has been predicted. Lightning strike initial damage has been simulated by translating the thermal field into degradation of elastic properties of the lamina. The results show an increase in the accumulated matrix damage and a decrease of tensile strength due to the initial lightning strike damage. For the maximum peak intensity of 40 kA, a decrease in tensile strength of 4.8% has been predicted

Salmorejo is a homogenate based on tomato, olive oil and breadcrumbs commercialized as a “fresh-like” cold puree in Spain and other European countries. Salmorejo is thermolabile and requires pasteurising upon High Temperature, Short Time (HTST) conditions to inhibit microbes and enzymes. Due to its penetration, dielectric heating by radiofrequency (RF) might improve pasteurisation results of conventional heating (CH) in viscous products. The objective was to validate the pasteurisation temperature (70-100 °C, at 5 ºC intervals) for salmorejo processed by radiofrequency (operating at 27.12 MHz for 9.08 s) or conventional continuous heating. Salmorejo was prone to thermal damage upon HTST conditions. Main heat-induced changes include: orangeness, flavour homogenisation, loss of freshness, thickening, loss of vitamin C and lipid oxidation. A ‘fresh-like’ good quality salmorejo can be obtained using either conventional or radiofrequency pasteurisers. Both CH and RF equivalent treatments allowed a strong reduction of total and sporulated mesophilic microorganisms, and an adequate inhibition of the pectinmethylesterase, peroxidase and, to a lesser extent, polyphenoloxidase, but did not inhibit the polygalacturonase enzyme. Pasteurisation at 80 °C for 9.8 s (RF) or 10.9 s (CH) provided a good equilibrium in levels of microbiological and enzymatic inhibition and thermal damage to the product. Increasing this temperature does not improve enzyme inactivation levels and salmorejo may become overheated.

The effect of low cycle fatigue (LCF) pre-damage on the subsequent very high cycle fatigue (VHCF) behavior is investigated in TC21 titanium alloy. LCF pre-damage is applied under 1.8% strain amplitude up to various fractions of the expected life and subsequent VHCF properties are determined using ultrasonic fatigue tests. Results show that 5% of LCF pre-damage insignificantly affects the VHCF limit due to the absent of pre-crack, but decreases the subsequent fatigue crack initiation life estimated by Pairs’ law. Pre-cracks introduced by 10% and 20% of LCF pre-damage significantly reduce the subsequent VHCF limits. The crack initiation site shifts from subsurface-induced fracture for undamaged and 5% of LCF pre-damage specimens to surface pre-crack for 10% and 20% of LCF pre-damage specimens in very high cycle region. The fracture mechanism analysis indicate that LCF pre-crack will re-start to propagate under subsequently low stress amplitude when stress intensity factor of pre-crack is larger than its threshold. Furthermore, the predicted fatigue limits based on EI Haddad model for the LCF pre-damage specimens well agree with the experimental results.

The angle of seismic excitation is a significant factor of the seismic response of RC buildings. The procedure required for the calculation of the angle for which the potential seismic damage is maximized (critical angle) contains multiple nonlinear time history analyses using in each one of them different angles of incidence. Moreover, the seismic codes recommend the application of more than one accelerograms for the evaluation of seismic response. Thus, the whole procedure becomes time consuming. Herein, a method to reduce the time required for the estimation of the critical angle based on Multilayered Feedforward Perceptron Neural Networks is proposed. The basic idea is the detection of cases in which the critical angle increases the class of seismic damage compared to the class which arises from the application of the seismic motion along the buildings’ structural axes. To this end, the problem is expressed and solved as Pattern Recognition problem. As inputs of networks the ratios of seismic parameters’ values along the two horizontal seismic records' components, as well as appropriately chosen structural parameters, were used. The results of analyses show that the neural networks can reliably detect the cases in which the calculation of the critical angle is essential.

Selected glasses with 10 Na₂O + (90-x) P₂O₅ + x BCD where bypass cement dust (BCD) x value =10, 20, 30 in mol% were synthesized by recognizable melting annealing technique. Cooperative characterization of the prepared glasses were carried out through FTIR and SEM analysis before and after immersed in simulated body fluid (SBF) solution for 13 and 23 days at 37 ^oC. After immersion in SBF, apatite layer is produced on the glass surface after 13 day and increase after 23 day, showing good bioactivity after immersion in the SBF especially for bioglass sample with 30% BCD. A porous hydroxy apatite layer produced on the surface of SBF-glass composite and this layer became denser after more soaking time, periods were extended from 13 to 23 days. Atomic absorption spectroscopy explained the early period of soaking that cause release of both Si and Ca ions through the glass beside decreasing of phosphrous ions. Bioglass (BCD-30) is studied as shielding for gamma, protons and alphas by using Phy-X software, SRIM Monte Carlo simulation code and its subroutine TRIM. The gamma shielding parameters, mass stopping power (MSP), range for both proton (H- ions) and alpha (He- ions) in bioglass- BCD-30 and human bone tissue have estimated. Also, comparison between them is calculated in predicting the radiation damage and atomic displacements per atom (dpa).

From the wide range of engineering materials traditional Stellite 6 alloy exhibits excellent cavitation erosion (CE) resistance. In this work, the effect of nitrogen ion implantation of HIPed Stellite 6 on the improvement of CE resistance and both cobalt-rich matrix phase transformation due to nitrogen implantation and CE were stated. The CE resistance of stellites ion-implanted by 120 keV N+ ions two fluences: 5x1016 cm-2 and 1x1017 cm-2 were comparatively analysed with the unimplanted stellite and AISI 304 stainless steel. CE tests were conducted according to ASTM G32 with stationary specimen method. Erosion rate curves and mean depth of erosion confirm that the nitrogen implanted HIPed Stellite 6 two times exceeds the resistance to CE than unimplanted stellite, and has almost 10 times higher CE reference than stainless steel. The X-ray diffraction (XRD) confirms that HIPed Stellite 6 nitrogen ion implantation favours transformation of the ɛ(hcp) to γ(fcc) structure. Unimplanted stellite ɛ-rich matirx is less prone to plastic deformation than γ and consequently, increase of γ phase effectively holds carbides in cobalt matrix and prevents Cr7C3 debonding. This phenomenon elongates three times the CE incubation stage, slows erosion rate and mitigates the material loss. Metastable γ structure formed by ion implantation consumes the cavitation load for work-hardening and γ → ɛ martensitic transformation. In further CE stages, phases transform as for unimplanted alloy namely, the cavitation-inducted recovery process, removal of strain, dislocations resulting in increase of fcc phase. The CE mechanism was investigated using a surface profilometer, atomic force microscopy, SEM-EDS and XRD. HIPed Stellite 6 wear behaviour relies on the plastic deformation of cobalt matrix, starting at Cr7C3/matrix interfaces. Once the Cr7C3 losing their restrain, are debonding and removed. Carbides detachment creates cavitation pits which initiate cracks propagation through cobalt matrix, the loss of matrix phase and CE proceeds with a detachment of massive chunk of materials.

Direct laser writing based on non-linear 3D nanolithography (also known as 3D laser lithography, 3DLL) is a powerful technology to manufacture polymeric micro-optical components. However, practical applications of these elements are limited due to the lack of knowledge of their optical resilience and durability. In this work, we employ 3DLL for the fabrication of bulk (i.e. fully filled) and woodpile structures out of different photopolymers. We then characterize them using S-on-1 laser induced damage threshold (LIDT) measurements. In this way, quantitative data of LIDT values can be collected. Furthermore, this method permits to gather damage morphologies. The results presented in this work demonstrate that LIDT values depend on the material and the geometry of the structure. Bulk non-photosensitized hybrid organic-inorganic photopolymer SZ2080 structures are found to be the most resilient with a damage threshold being of 169±15 mJ/cm².

In this paper, the results of finite element analyses of a single-layer cylindrical latticed shell under severe earthquake is presented. A 3D Finite Element model using fiber beam elements were used to investigate the collapse mechanism of this type of shell. The failure criteria of structural members are simulated based on the theory of damage accumulation. Severe earthquake of peak ground acceleration (PGA) of 500 gal was applied to the shell. The stress and defeomation of the shell were studied in detail. A three-stages collapse mechanism “double-diagonal -members-failure-belt” of this type of structure was discovered. Based on the analysis results, the measures to mitigate collapse of this type of structure is recomanded.

Chronic obstructive pulmonary disease (COPD) is a respiratory disease associated with airways inflammation and lung parenchyma fibrosis. The primary goals of COPD treatment are to re-duce symptoms and risk of exacerbations, therefore pulmonary rehabilitation is considered the key component of managing COPD patients. Oxidative airway damage, inflammation and re-duction of endogenous antioxidant enzymes are known to play a crucial role in the pathogenesis of COPD. Natural antioxidants have also recently been considered as they play an important role in metabolism, DNA repair and fighting the effects of oxidative stress. In this paper we evaluated the response of 105 elderly COPD patients to pulmonary rehabilitation (PR), based on high or low vegetable consumption, by analyzing clinical parameters and biological measure-ments at baseline and after completion of the three weeks PR. We found that high vegetable in-take in normal diet, without any specific intervention, can increase the probability to success-fully respond to rehabilitation (65.4% of responders ate vegetables daily vs. 40.0% of Non-Responders, p=0.033). Three weeks of pulmonary rehabilitation are probably too short to reveal a reduction of the oxidative stress and DNA damage, but are enough to show an im-provement in the patient's inflammatory state.

Existing studies often lack a systematic solution for Unmanned Aerial Vehicles (UAV) inspection system, which hinders their widespread application in crack detection. To enhance its practicality, this study proposes a formal and systematic framework for UAV inspection systems, specifically designed for automatic crack detection and pavement distress evaluation. The framework integrates UAV data acquisition, deep learning based crack identification, and road damage assessment in a comprehensive and orderly manner. Firstly, the flight control strategy is presented, and road crack data is collected using the DJI Mini 2 UAV imagery, establishing a high-quality UAV crack image datasets with ground truth information. Secondly, a validation and comparison study is conducted to enhance the automatic crack detection capability and provide an appropriate deployment scheme for UAV inspection systems. This study develops automatic crack detection models based on mainstream deep learning algorithms(namely, Faster-RCNN, YOLOv5s, YOLOv7-tiny, and YOLOv8s) in urban road scenarios. The results demonstrate that the Faster-RCNN algorithm achieves the highest accuracy and is suitable for online data collection of UAV and offline inspection at work stations. Meanwhile, the YOLO models, while slightly lower in accuracy, are the fastest algorithm and are suitable for lightweight deployment of UAV with online collection and real-time inspection. Quantitative measurement methods for road cracks are presented to assess road damage, which will enhance the application of UAV inspection systems and provide factual evidence for maintenance decisions made by road authorities.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

Chronic obstructive pulmonary disease (COPD) is a respiratory disease associated with airways inflammation and lung parenchyma fibrosis. The primary goals of COPD treatment are to re-duce symptoms and risk of exacerbations, therefore pulmonary rehabilitation is considered the key component of managing COPD patients. Oxidative airway damage, inflammation and re-duction of endogenous antioxidant enzymes are known to play a crucial role in the pathogenesis of COPD. Natural antioxidants have also recently been considered as they play an important role in metabolism, DNA repair and fighting the effects of oxidative stress. In this paper we evaluated the response of 105 elderly COPD patients to pulmonary rehabilitation (PR), based on high or low vegetable consumption, by analyzing clinical parameters and biological measure-ments at baseline and after completion of the three weeks PR. We found that high vegetable in-take in normal diet, without any specific intervention, can increase the probability to success-fully respond to rehabilitation (65.4% of responders ate vegetables daily vs. 40.0% of Non-Responders, p=0.033). Three weeks of pulmonary rehabilitation are probably too short to reveal a reduction of the oxidative stress and DNA damage, but are enough to show an im-provement in the patient's inflammatory state.

Ferroptosis, a regulated form of cell death characterized by iron-dependent lipid peroxide accumulation, plays a pivotal role in various pathological conditions, including neurodegenerative diseases. While reasonable evidence for ferroptosis exist e.g. in Parkinson’s disease or Alzheimer’s disease, there are only few reports on amyotrophic lateral sclerosis (ALS), a fast progressive and incurable neurodegenerative disorder characterized by progressive motor neuron degeneration. Initial studies, however, highlight that ferroptosis might be significantly involved in ALS. Key features of ferroptosis include oxidative stress, glutathione depletion, mitochondrial and dysfunction alterations in mitochondrial morphology, mediated by proteins such as GPX4, xCT, ACSL4 FSP1, Nrf2 and TfR1. Induction of ferroptosis involves small molecule compounds like erastin and RSL3, which disrupt system Xc- and GPX4 activity, respectively, yielding in lipid peroxidation and cellular demise. Mutations in Fused in Sarcoma (FUS) are associated with familial ALS. Pathophysiological hallmarks of FUS-ALS involve mitochondrial dysfunction and oxidative damage, implicating ferroptosis as putative cell death pathway in motor neuron demise. However, mechanistic understanding of ferroptosis in ALS, particularly FUS-ALS, remains limited. Here, we investigated ferroptosis vulnerability in a FUS-ALS cell model, revealing mitochondrial disturbance and increased susceptibility for ferroptosis in cells harboring the mutant FUS variant. This was accompanied by altered expression of ferroptosis-associated proteins, particularly by dramatic reduction of xCT expression, leading to cellular imbalance of the redox system and increased lipid peroxidation. Iron chelation with deferoxamine as well as inhibition of the mitochondrial calcium uniporter (MCU) significantly alleviated ferroptotic cell death and lipid peroxidation. These findings suggest a link between ferroptosis and FUS-ALS, offering potential therapeutic targets.

N6-methyladenosine (M6A) modification is the most abundant internal chemical modification on RNA molecules in eukaryotes and can affect mRNA metabolism and regulate RNA transcription, nuclear export, splicing, degradation, translation, ets, and has a significant impact on various aspects of physiology or pathobiology. Radiotherapy is the most common measure of tumor treatment, variety of cellular intrinsic mechanisms affect the responses of cells to ionizing radiation (IR) and effectiveness of cancer radiotherapy. In this review, we summarize and discuss the recent advances about the roles and mechanisms of RNA M6A methylation in cellular responses to radiation-induced DNA damage response, and outcomes of cancer radiotherapy. Insights into the RNA M6A methylation in radiation biology may facilitate the improvement of therapeutic strategies for cancer radiotherapy as well as radioprotection on normal tissues.

Melon pest management relies on the excessive application of pesticides. Reducing pesticide spraying has become a global issue for environmental sustainability and human health. Therefore, developing a new cropping system that is sustainable and eco-friendly is important. This study found that melon seedlings irrigated with ultrafine water containing H2 and O2 (UFW) produced more root hairs, increased shoot height, and produced more flowers than the control irrigated with reverse osmosis (RO) water. Surprisingly, we also discovered that UFW irrigation significantly reduced aphid infestation in melon. Based on cryo-scanning electron microscope (cryo-SEM) observations, UFW treatment enhanced trichome development and prevented aphid infestation. To investigate whether it was H2 or O2 that helped to deter insect infestation, we prepared UF water enrichment of H2 (UF+H2) and O2 (UF+O2) separately and irrigated melons. Cryo-SEM results indicated that both UF+H2 and UF+O2 can increase the density of trichomes in melon leaves and petioles. RT-qPCR showed that UF+H2 significantly increased the gene expression level of the trichome-related gene GLABRA2 (GL2). We planted melons in a plastic greenhouse and irrigated them with ultrafine water enrichment of hydrogen (UF+H2) and oxygen (UF+O2). The SPAD value, photosynthetic parameters, root weight, fruit weight, and fruit sweetness were all better than the control without ultrafine water irrigation. UFW significantly increased trichome development, enhanced insect resistance, and improved fruit traits. This system thus provides useful water management for pest control and sustainable agricultural production.

Breast cancer is a serious disease and the second leading cause of cancer-related death among women in the U.S. New treatments for this aggressive disease are urgently needed. Repurposing FDA-approved drugs for cancer treatment is an alternative that saves time and lowers the costs needed for drug development. In this study, we investigated the effects of proguanil, an anti-malarial drug, in breast cancer cells. Proguanil exhibited a significant cytotoxic effect on breast cancer cell lines including patient derived cell lines. Proguanil caused apoptosis through increased production of ROS and consequent decrease of mitochondrial membrane potential, mitochondrial respiration, and ATP production rates. ROS generation by proguanil was up to 3-fold higher when compared to the control. Proguanil treatment increased the expression of Bax, p-H2AX, cleaved-caspase 9, cleaved PARP, and down-regulated bcl-2 and survivin in breast cancer cell lines. The enlargement of 4T1 breast tumors in female Balb/c mice was suppressed by 55% through daily oral administration of 20mg/kg of proguanil. Western blot analyses of proguanil- treated tumors showed increased levels of p-H2AX, Bax, c-PARP, and c-caspase3 compared to control. Proguanil proved to be an efficient in vitro and in-vivo inhibitor of breast cancer cells, hence should be considered further for clinical investigation against breast cancer.

Cardiac hypertrophy typically follows myocardial damage, a process known to involve members of the Krüppel-Like Factors (KLFs) which have pro-hypertrophic and anti-hypertrophic roles. Our study delved into the molecular mechanisms underlying KLFs-cardiac hypertrophy interplay post myocardial infraction. We induced myocardial dam-age in rats using isoproterenol. Total RNA was extracted from the left ventricle and Quantitative Real Time RT-PCR was conducted to assess the expression of KLFs, cardiac commitment genes, inflammatory markers, and certain conduction-related genes. We devel-oped a computational approach to construct a proteomic network centered on KLFs. Initial results revealed early expression (2-3 days post-induction) of KLF3, KLF4 and KLF6, followed by the subsequent expression of KLF11 and KLF15 (5-8 days after induction). In the maturation stage, KLF12 and KLF13 regulators were found upregulated. IL-6 was gradually found to be upregulated through. Interaction analysis revealed KLF3, KLF8 and KLF12 interacted with cardiac electrical functions. RT-PCR confirmed up-regulation in cardiac genes linked to electrical function and scar maturation. Our findings underscore the central role of KLFs during the modulation of the cardiac hypertrophic response. Dysregulation of KLF expression resulted in damaged myocardium, participating in the progression of abnormal hypertrophy, highlighting their potential as therapeutic targets for heart diseases.

Model-based approaches form the basis of the majority of damage detection and localization studies; however, built-in online detection technique can offer an alternative for future structural health monitoring technologies. Thus, in this paper, we present a dynamic localization algorithm for damage localization in functionally graded plates. The method depends on the creation of a grid matrix that contains the dynamic response of the structure over time. Subsequently, an optimization process is carried out via a linear equation representing the information contained within the grid to achieve accurate localization of damage. Due to the inherent sparsity of the localization nature, the FISTA algorithm has been employed as a problem solver. The approach is tested in the case of the functionally graded plate under clamped free boundary conditions. Several, damage scenarios were investigated for the case of damage signals on and off the grid. The results show that the proposed approach is capable of accurately predicting damage position and can be suitable for use in low size data systems.

In order to study the strength changes of concrete specimens under different loading conditions, based on the principle of minimum energy dissipation and from the Angle of concrete failure energy per unit area, the finite element numerical simulation software was applied to concrete specimens with different failure modes of tension, compression, bending and torsion, and the double-broken line damage constitutive model was adopted to simulate and analyze the failure forms of concrete specimens under different loading conditions. The failure area and failure energy of each specimen during loading were quantitatively calculated under each failure mode, and the relationship between the failure area and failure energy consumed under different failure modes was analyzed. The results show that under different failure modes, the failure area of concrete specimens is different, the energy consumed during failure is different, and the strength is different. However, in the process of failure, no matter how the failure mode changes, the failure energy W per unit area remains unchanged and is a constant, which is related to the physical properties of concrete itself.

The azimuth wheel-rail of large aperture radio telescope is the key component, it not only sup-ports the whole weight of the antenna, but also directly affects the pointing performance of the antenna with its surface accuracy. The whole weight of the radio telescope is hundreds or even thousands of tons, its azimuth frame rollers have great contact stress with the wheel-rail surface, repeated rolling can cause rolling contact fatigue on the wheel-rail surface, resulting in wear, cracks and other damage to the wheel-rail, and even lead to failure or fracture of the wheel-rail in serious cases, so it is very important to monitor the damage of the antenna wheel-rail. In order to visually detect the use of antenna wheel-rail surface, this paper proposed the method using electromagnetic ultrasonic detection to detect the damage of antenna wheel-rail surface for the first time. Based on the electromagnetic ultrasonic nondestructive testing principle, the simplified wheel-rail model containing wear, corrosion and crack damage is simulated. The results show that this method can effectively detect the surface damage of the antenna wheel-rail surface, and it can provide an important reference for the research of wheel-rail damage detection of large radio telescope.

Impact of Nitrogen Foamed Stimulation Fluids Stabilized by Nanoadditives on Reservoir Rocks of Hydrocarbon Deposits

Following the occurrence of a typhoon, quick damage assessment related to residents can facilitate quick dispatch of house repair and disaster insurance works. Employing a deep learning method, this study used aerial photos of the Chiba prefecture obtained following the Typhoon Faxai in 2019 to automatically detect and evaluate the roof damage. This study comprised three parts: training deep learning model, detecting the roof damage using trained model, and classifying the level of roof damage. The detection object comprised roof outline, blue tarps, and roof completely destroyed. The roofs were divided into three categories: roof without damage, roof with blue tarps and roof completely destroyed. the F value obtained using the proposed method was higher than those obtained using other methods. In addition, it can be further divided into 5 levels from level 0 to 4. Finally, the spatial distribution of the roof damage was analyzed using ArcGIS tools. The proposed method is expected to provide certain reference for the real-time detection of the roof damage after the occurrence of a typhoon.

Background: Uncontrolled hemorrhage is a major preventable cause of death in patients with trauma. However, the majority of large animal models of hemorrhage have utilized controlled hemorrhage rather than uncontrolled hemorrhage to investigate the impact of immunopathy and coagulopathy on multi-organ failure (MOF) and mortality. This study evaluates these alterations in a severe porcine-controlled and uncontrolled hemorrhagic shock (HS) model. Methods: Anesthetized female swine underwent controlled hemorrhage (22 ml/kg) and uncontrolled hemorrhage by partial splenic resection followed with or without lactated Ringer solution (LR) or Voluven® resuscitation. Blood chemistry, physiologic variables, systemic and tissue levels of complement proteins and cytokines, coagulation parameters, organ function, and damage were recorded and assessed. Results: HS resulted in systemic and local complement activation, cytokine release, metabolic acidosis, hyperkalemia, MOF, and no animal survival. Resuscitation with LR and Voluven® after HS improved hemodynamic parameters (MAP and SI), metabolic acidosis, hyperkalemia, and survival but resulted in increased complement activation and worse coagulopathy. Compared with the LR group, the HS animal treated with Voluven® had worse dilutional anemia, coagulopathy, renal and hepatic dysfunction, increased myocardial complement activation and renal damage, and decreased survival rate. Conclusions: Hemorrhagic shock triggers early immunopathy and coagulopathy that appear associated with MOF and death. This study indicates that immunopathy and coagulopathy are therapeutic targets that may be addressed with a high-impact adjunctive treatment to conventional resuscitation.

The open hole tensile and flexural test of composites holds immense importance in aerospace and structural engineering. These tests provide critical insights into how composites perform under real-world conditions, allowing for the development of materials that meet rigorous standards, thereby ensuring the safety and durability of aircraft and other applications. This study investigates the influence of hole size on the open hole tensile (OHT) and flexural properties (OHF) of plane woven aramid/epoxy (AFRP), basalt/epoxy (BFRP), and aramid-basalt/epoxy (ABFRP) sandwiched laminates. Specimens with three different hole sizes viz., 4 mm, 6 mm, 8 mm were prepared and tested according to ASTM D5766 and ASTM D7264 for OHT and OHF performance respectively. Results indicated that the hybridization of aramid-basalt layers in a sandwich lay up significantly improved the mechanical performance when compared to only aramid laminate. However, with the increase in hole size the mechanical properties declined irrespective of the material. Basalt fibres showed higher hole sensitivity under tensile loading due to its brittle fracture mechanism while aramid fibres exhibited higher hole sensitivity under flexural loading which can be attributed to its the poor compressive strength. The effect of hole size on the damage mechanism has also been highlighted through scanning electron microscope (SEM). Major failure modes observed are delamination around the hole edges, ductile and brittle fibre fractures, and delamination.

Caused by age or trauma, collapsed connective tissue can cause nerve entrapment and damage within the tarsal tunnel. Tarsal tunnel syndrome is relatively underdiagnosed. This study presents an intervention targeting damaged tissues surrounding the nerves and replacing the structural cushioning with a Wharton’s jelly tissue allograft. The eight selected patients from four clinical sites had tarsal tunnel-related defects. Patient outcomes were tracked on a 90-day calendar utilizing the Numeric Pain Rating Scale (NPRS) and the Western Ontario and McMaster University Arthritis Index (WOMAC). All patients had failed standard care practices for at least six weeks. Each patient received a Wharton’s jelly tissue allograft to sites around the affected tarsal tunnel. No patients experienced adverse reactions. Percent change calculated from the initial application to the 90-day follow-up showed an improvement of 59.43% in NPRS and a 37.58% improvement in WOMAC. This study provides evidence that WJ allograft applications are safe, minimally invasive, and efficacious for patients who have failed standard care treatments for tissue defects associated with Tarsal Tunnel syndrome. Limitations include the small cohort size and nonblinded nature. The results of this study warrant further research to confirm the efficacy, optimal dose, protocol, and durability of Wharton's jelly.

Oxidative stress (OS) plays a crucial role in placental pathogenesis and pregnancy-related complications. This review explores OS's impact on placental development and function, focusing on novel biomarkers for early detection of at-risk pregnancies and emerging therapeutic strategies. We analyzed recent research on OS in placental pathophysiology, examining its sources, mechanisms, and effects. While trophoblast invasion under low-oxygen conditions and hypoxia-induced OS regulate physiological placental development, excessive OS can lead to complications like miscarriage, preeclampsia, and intrauterine growth restriction. Promising OS biomarkers, including malondialdehyde, 8-isoprostane, and the sFlt-1/PlGF ratio, show potential for early detection of pregnancy complications. Therapeutic strategies targeting OS, such as mitochondria-targeted antioxidants, Nrf2 activators, and gasotransmitter therapies, demonstrate encouraging preclinical results. However, clinical translation remains challenging. Future research should focus on validating these biomarkers in large-scale studies and developing personalized therapies to modulate placental OS. Emerging approaches like extracellular vesicle-based therapies and nanomedicine warrant further investigation for both diagnostic and therapeutic applications in pregnancy-related complications. Integrating OS biomarkers with other molecular and cellular markers offers improved potential for early identification of at-risk pregnancies.

Aluminium alloys are used for fabrication of fuel clad of research grade nuclear reactors as well as of several types of core components of high flux research reactors. In order to carry out design and safety analysis of these components, their mechanical and fracture properties are required by the designer. In this work, experiments have been conducted on tensile specimens machined from an aluminium alloy block to evaluate the material stress-strain curve. For evaluation of fracture properties, experiments have been conducted on disc shaped compact tension specimens in order to determine the fracture toughness of aluminium alloy. From crystal plasticity based finite element analysis and experimental data, a material damage parameter for prediction of crack initiation has been evaluated. The variation of the parameter for various values of initial a/W ratios of the disc-shaped CT specimens have been studied. It was observed that the damage parameter is independent of crack geometry and hence, it qualifies as transferable material property which can be used to predict crack initiation in a component of this material subjected to different kinds of loading conditions. In addition, the JR curves of the disc-shaped CT specimens have also been evaluated from experiments. The material damage parameter has also been used to study the crack initiation in single crystal fracture specimens with two different orientations. It was observed that the [111] orientation is more susceptible to crack initiation and propagation compared to the [100] orientation as the damage parameter is high in the ligament of the specimen ahead of the crack-tip for the same level of load. The results of the experiments and the material damage parameter shall be helpful for integrity analysis of fuel clad of research reactors as well as components of high flux research reactors.

Pathological aseptic calcification is the most common form of structural valvular degeneration (SVD), leading to premature failure of heart valve bioprostheses (BHVs). The processing methods used to obtain GA-fixed pericardium-based biomaterials determine the hemodynamic characteristics and durability of BHVs. This article presents a comparative study of the effects of several processing methods on the degree of damage to the ECM of GA-fixed pericardium-based biomaterials as well as on their biostability, biocompatibility, and resistance to calcification. Based on the assumption that preservation of the native ECM structure will enable the creation of calcinosis-resistant materials, this study provides a soft biomimetic approach for the manufacture of GA-fixed biomaterials using gentle decellularization and washing methods. It has been shown that the use of soft methods for preimplantation processing of materials, ensuring maximum preservation of the intactness of the pericardial ECM, radically increases the resistance of biomaterials to calcification. The data obtained are of interest for the development of new calcinosis-resistant biomaterials for the manufacture of BHVs.

Hepatitis D virus (HDV) infection represents the most severe form of chronic viral hepatitis. We have shown that the delivery of HDV replication-competent genomes to the hepatocytes using adenoassociated virus (AAV-HDV) as gene delivery vehicles offers a unique platform to investi-gate the molecular aspects of HDV and associated liver damage. Here, we generated HDV ge-nomes modified by site directed mutagenesis aimed to: i) prevent some post-translational modi-fications of HDV antigens (HDAgs) such as Large-HDAg (L-HDAg) isoprenylation or Short-HDAg (S-HDAg) phosphorylation ii) alter the localization of HDAgs within the subcellular compartments and iii) inhibit the right conformation of the delta ribozyme. First, the different HDV mutants were tested in vitro using plasmid-transfected Huh-7 cells and then in vivo in C57BL/6 mice using AAV vectors. We found that Ser 177 phosphorylation and the ribozymal ac-tivity are essential for HDV replication and HDAg expression. Mutation of the isoprenylation domain prevent the formation of infectious particles and increase cellular toxicity and liver dam-age. Finally, altering the intracellular localization od HDAg have a profound on viral replication in vivo but liver toxicity is maintained. Mutation in the nuclear export signal impair the for-mation of infectious viral particles. These findings contribute valuable insights into the intricate mechanisms of HDV biology and have implications for therapeutic considerations

Marine mortar was the goal material and its multi-scale physical-chemical-mechanical characteristics were the principal interest in this study. The on-line multi-scale damage detection experiments art was designed to quantify the characteristics mathematically and graphically. The normal cylinder specimen with 70-day age was produced and investigated by dynamically global MSHCT scan and local detection of EDS, SEM and XRD. The experiments results indicated that the marine mortar offered the appreciable strength at the early age at least, although some saline minerals were generated during the preparation. The micro-interfacial behavior and the parental foci controlled the damage development of the marine mortar the performance of which was still the adjustable one by the composition optimization.

Aiming at the damage detection and continuous monitoring of high efficiency composite structure, the method of carbon nano sensor embeded in the 3-D braided composite material specimen was put forward and the method of damage location for 3-D braided composite material was described. In this paper, the mechanical and electrical characteristics of carbon nano-fiber were analyzed. Considering the massive data of the health monitoring of composite processing, to ensure that the system has good real-time performance, quaternary matrix Singular Value Decomposition algorithm is proposed to simplify data and improve the efficiency of the algorithm. The existence of injury is determined and the damage location is calculated by comparing with key features of healthy specimen. Experimental results prove the method is feasible and effective.

Astronauts in space are subject to a continuous bombardment of ionizing radiation. The Earth's magnetic field and the ISS shield some biologically damaging particles traveling through. Still, travel beyond low-Earth orbit and extravehicular activities are exceedingly more dangerous and there is a concern for the acute and late-occurring adverse health effects befalling astronauts. So, it is vital to consider the current tools and models used to describe and study the organic consequences of ionizing radiation exposure. It is equally important to see where these models may improve. This article reviews the historical development and current state of knowledge of radiation effects impacting astronauts in orbit. We explain the space radiation environment, cellular microenvironment, and how these may be incorporated in radiobiological models to aid in our understanding of the influence space travel may have on astronaut health. The topics discussed in this paper include a review of DNA damage and repair mechanisms and the numerical models that aim to explain the biological effects resulting from ionizing radiation damage. Historically, radiobiological models focused on how radiation damages nuclear DNA, built upon the hypotheses of Crowther and Lea in the 1940s and 1960s, and neglected other sub-cellular targets outside of nuclear DNA.

There is a confusion in the original design concept for the tensioning of longitudinally connected reinforcement of CRTSII slab ballastless track. In order to clarify the effect of tension value of longitudinal reinforcement on mechanical characteristics of ballastless track, a three dimensional finite element model considering the nonlinear interaction between the track slab and CA mortar of CRTSII slab ballastless track was established. The mechanical characteristics of the track structure under longitudinal tension load and temperature gradient load of the longitudinal joint were calculated. A method of applying pre-stress to post-pouring concrete was proposed according to the concept of pre-stress loss of pretensioning pre-stressed concrete, reasonable tensile force value was proposed after the crack width and the reinforcement stress of the ballastless track in the operation stage were checked and calculated according to the concrete design principle. When the tension force is greater than 300 kN, it’s harmful to the bonding between the slab and mortar layer, which is prone to interlayer damage. In order to adding pre-stress to concrete of wide joints to ensure the longitudinal stability of ballastless track and the reinforcement stress and crack width to meet the design requirements. It is suggested that the tension force value should be 230 kN, and the temperature difference between reinforcement and concrete should be 30 °C before the initial curdle of wide joint concrete.

Nonlinear catastrophes caused by geological fluids are a fundamental issue in rock mechanics and the geoengineering hazard field. For the consideration of hydrodynamic force on red-bed mudstone softening damage, X-ray visualization test on the fissure flow in mudstone block failure under hydrodynamic force was performed in this study based on block scale and the physical phenomena of fissure seepage and nonlinear diffusion were further explored. A new method for evaluating the hydro-damage degrees of rocks using an X-ray image analysis was proposed, and the quantitative relation of diffusion coefficients of hydro-damage and seepage was established. The research results revealed that the hydrodynamic force promoted the fluid-filled fissure behavior in mudstone specimen failure. Also, the seepage and diffusion phenomena of fluid in rocks during failures were indicated using X-ray imaging. A dual mechanical behavior was presented in the nonlinear seepage and abnormal diffusion of a red mudstone geological body under hydrodynamic conditions. The damaged degree of mudstone was aggravated by the effect of hydrodynamic force, and the initial seepage–diffusion coefficient with respect to lower hydro-damage was larger than the final seepage–diffusion coefficient with respect to higher hydro-damage of rocks with a decreasing nonlinear trend.

The tension cable-supported power transmission structure (TC-PTS) is a new type of power transmission structure suitable for mountainous terrain, which is sensitive to wind load. In this regard, a nonlinear finite element analysis model of wind-induced vibration is proposed for the TC-PTS, and the wind-induced vibration response of the structure is analyzed. Firstly, the tangent stiffness matrix of the three-dimensional truss element for the supporting suspension cable and transmission line, considering the geometric nonlinearity of structures, is derived through the relationship between the element elastic energy and its displacement. Subsequently, the element mass matrix and damping matrix of the supporting suspension cable and transmission line, as well as the element nodal load vector obtained from wind load equivalence are given. Then, based on the nonlinear finite element theory, the nonlinear dynamic equation of wind-induced vibration is established for the TC-PTS and solved by Newmark-β method combined with Newton-Raphson iterative method. Furthermore, the rain-flow counting method and Miner's linear fatigue cumulative damage theory were used for wind induced fatigue damage assessment. Finally, a two-span TC-PTS is selected as an example, and the wind-induced nonlinear vibration and fatigue damage assessment are analyzed through the proposed model. The results show that the proposed model has high computational accuracy and efficiency. With the increase of wind speed and wind direction angle, the maximum lateral displacement and tension of the supporting suspension cable and transmission line increase, and their degree of increase shows a nonlinear trend. In terms of the wind-induced fatigue analysis results of TC-PTS, the fatigue damage at the end of the supporting-conductor suspension cable is greater than the fatigue damage at its midpoint. Compared to the fatigue damage at the midpoint of the conductor, the fatigue damage at the end of the conductor is less affected by wind direction angle, and both are more significantly affected by the wind speed.

Polymethyl methacrylate (PMMA) polymer is widely used in various fields today. In order to thoroughly reveal the structural impact performance of PMMA materials, this paper is based on the comprehensive Johnson-Cook constitutive model and damage failure model, and accurately confirm the J-C constitutive and damage failure model parameters of PMMA through material test data, The dynamic process of steel bullet impacting PMMA plate structure is analyzed by finite element software ABAQUS. The calculation results show that the numerical simulation results in this paper are in good agreement with the experimental test data. Therefore, the feasibility and accuracy of the impact analysis of PMMA structures based on J-C constitutive and damage failure models in this paper are studied. Finally, based on the J-C constitutive model and damage failure model, the variation of the residual velocity of the bullet with the PMMA plate thickness is analyzed in depth, that is, the results show that the residual velocity of the bullet has a certain linear relationship with the plate thickness.

The past is an important lesson for facing the future with greater awareness. In this context, school plays a key role to spread knowledge on natural phenomena and to promote behavior change. Together with researchers, teachers can be strong allies to build more resilient future citizens. The Istituto Nazionale di Geofisica e Vulcanologia (INGV) school training activities provide tools to get ready for the next earthquake and/or tsunamis. About 5000 students from both Middle schools (ISCED 2) and High schools (ISCED 3) were involved in active learning activities based on a flipped-up approach during special online scientific events in the Pandemic. Online lab activities were conducted respectively during the European Researchers’ Night (“Earthquakes: history teaches us the future: researchers for a day with experimentation in didactics for ESL”) and during the World Water Day 2021 and the World Earth Day 2021 (“Tsunamis: history teaches us the future researchers for a day with experimentation in didactics for ESL”). These two Episodes of Situated Learning (ELS) experiences triggered students’ interest, favoring remote learning, developing life skills, focusing on historical seismic studies of both past earthquakes and tsunamis.

With the deterioration of the bridge performance and ever-increasing amount of traffic, the bridge safety is becoming a concern for engineering community. A method that can assess the bridge's condition in real-time is urgently needed. The main factors that hinder the bridge condition assessment are the uncertain operational environments. A new moving principal component analysis (MPCA) based method is developed for structural damage detection of bridges in operational environments in this paper. Two main operational environmental factors: the environmental temperature and traffic loads, are studied in the assessment process to verify the robustness and practicality of the proposed method. The numerical and experimental results show that the proposed method is effective and accurate to assess the bridge condition in operational environments.

Aircraft heat exchangers play a crucial role in maintaining thermal balance and ensuring that essential components operate efficiently and safely. In this context, it is highly relevant to gain knowledge about the deterioration and the predominant damage mechanisms of these components. In this study, two different non-destructive methods are employed to analyze the damage initiation of a heat exchanger part during fatigue test. On the one hand, Acoustic Emission technique is employed using membrane-free microphones capable of capturing a broad bandwidth. The acoustic events were classified by a machine learning algorithm to determine their source and damage mechanisms. On the other side, Digital Image Correlation (DIC) allowed the measurement of the strain evolution along the test and more precisely, redistributions were considered as damage indicators. As a result, it was identified that AE served as early damage indicator as the cumulative number of events was in good agreement with the severity of the damage. With respect to classification two clear clusters ascribed to different type of events were identified. In the case of DIC, strain redistributions gave clear indications of damage or deterioration but at a later stage compared to AE

Cellular aging has drawn the attention of researchers, scientists, and biotech businesses for the treatment of a number of medical conditions. Cellular aging is primarily defined by consistent cessation of proliferative development in response to internal and external stressors, including DNA damage, telomere shortening, mitochondrial dysfunction, and regulation of the senescence-associated secretory phenotype (SASP). Disturbances involving these factors may contribute to age-related disease development. Therefore, the current review aims to explore anti-aging factors targeting DNA damage response and SASP regulation and their detailed signaling networks. In addition, it provides an opportunity for researchers to identify not only anti-aging targets, but also anti-aging therapeutic strategies based on identified and non-identified targets.

The contexts where there is mining and agriculture activities are potential sources of risk to human health due to contamination by chemical mixtures. This study explored the association between the frequency of micronuclei and pesticides in regions with ferronickel (Montelibano, Córdoba) and gold (Nechí, Antioquia) mining, and a closed native mercury mine (Aranzazu, Caldas). A cross-sectional study was carried out with 247 residents in the mining regions. Sociodemographic, occupational, and toxicological variables were ascertained. Blood and urine samples were taken for pesticide analysis (12 organochlorines, organophosphates, and carbamates), 68 chemical elements were quantified in hair, and micronuclei (MN) were quantified in lymphocytes. The mixtures of chemical elements were grouped through exploratory factor analysis. Prevalence ratios (PR) were estimated with robust variance Poisson regressions to explore associations. The highest concentrations of chemical elements were in the active mines. The potentially most toxic chemical mixture was observed in the ferronickel mine. Pesticides were detected in a low proportion of participants. The frequency of MN was similar in the three mining contexts. There was great heterogeneity in the exposure to pesticides and chemical elements. The “hormetic effect” of selenium is described, in which at low doses it acts as a chelator and at high doses it can enhance the toxic effects of other elements. It is proposed that future studies in mining contexts include the measurement of chemical mixtures to better assess exposure and potential adverse health effects.

Background: Morphological alterations in intracranial pressure pulse waveform (ICPPW) secondary to intracranial hypertension (ICP >20 mmHg) and reduction in intracranial compliance (ICC) are well known indicators of neurological severity. To date, no studies have documented the ICPPW modifications after intracranial hypertension resolution with decompressive craniectomy (DC). The present study aimed to assess the morphological alterations in ICPPW among neurocritical care patients with and without DC, by comparing the variations of ICPPW features according to elevations in mean ICP values. Methods: Patients requiring ICP monitoring because of severe traumatic or spontaneous conditions were included. Mean ICP values were compared with ICPPW features (P2/P1 ratio, TTP and pulse amplitude). Elevation in ICP was produced by means of ultrasound-guided manual internal jugular veins compression. Results were distributed for three groups: intact skull (exclusive burr hole for ICP monitoring), craniotomy/large fractures (group 2) or DC (group 3). Results: 57 patients were analyzed. 21 (36%) presented no skull defects, whereas 15 (26%) had DC. ICP was not significantly different between groups: ±13.59 for intact and ±17.66 mmHg for DC, with ICP induced elevation also similar between groups (p= 0.56). Significant elevation was observed for P2/P1 ratio for groups 1 and 2, whereas reduction was observed in group 3 (elevation of ±0.09 for groups 1 and 2, whereas reduction of 0.03 for group 3, p=0.01). Conclusion: In the present study, intracranial pressure pulse waveform analysis indicated that intracranial compliance was significantly more impaired among decompressive craniectomy patients, although ICPPW indicated DC to be protective for further influences of ICP elevations over the brain. Analysis of ICPPW seems to be an alternative to real time ICC assessment.

The purpose of this study was to better understand the interactive impact of two soil-borne pathogens, Phytophthora cactorum (as the primary pathogen) and Armillaria gallica (as secondary), on two-year-old seedlings of silver birch (Betula pendula) subjected to stress caused by mechanical defoliation simulating primary insect feeding. One year after treatments, the chlorophyll fluorescence measurement and gas chromatography coupled with mass spectrometry (GC-MS) were used to analyze the photosynthetic activity in leaves, the volatile organic compounds (VOCs) emitted by birch leaves and chemical compounds from roots. Only the infection of roots by P. cactorum increased photosynthetic rates in the leaves, which may suggest its cryptic development in contrast to fungi. The birch leaves in seedlings exposed to 50% defoliation, inoculation with P. cactorum and A. gallica emitted more aromatic carbonyls and alcohols, as well as half as much aliphatic esters, compared to untreated controls. In infected birch roots, the production of phenols, triterpenes and fatty alcohols increased, but fatty acids decreased. This was the first experimental confirmation of the pathogenicity of P. cactorum on silver birch seedlings in Poland. The most severe damage to roots took place only in the case of two-way or three-way interactions. Higher levels of aromatic carbonyls and alcohols in leaves, as well as phenolic compounds in roots of stressed birches (compared to control) suggest an activation of plant systemic acquired resistance (SAR).

New corrosion inhibitor derived from coumarin-3-amine namely 3-((2-chlorobenzylidene)amino)coumarin was synthesized and characterized by CHN elemental analysis in addition to Fourier transform infrared and nuclear magnetic resonance techniques. The anti-corrosion ability of 3-((2-chlorobenzylidene)amino)coumarin to inhibit the impacts of corrosion has been demonstrated and damage reduction of the mild steel also. 3-((2-chlorobenzylidene)amino)coumarin, has been employed as a good corrosion inhibitor for mild steel in HCL solution. The efficiency of the inhibition was figured according to weight loss method and it was 74.6%.

The enterohemorrhagic Escherichia coli (EHEC) O157: H7 EspF is known to be a multifunctional effector that triggers several damage processes in the host cells. However, in the process of EHEC O157: H7 infection, the interactions between EspF, its N- or C-terminus, and host proteins are still unclear. In this work, we use co-immunoprecipitation combined with mass spectrometry (CoIP-MS) to screen the interactions between EspF/EspF-N/EspF-C terminus and host proteins. A total of 311 host proteins are analyzed. The N-terminus of EspF is found to interact with 192 proteins, whereas 205 proteins interact with the C-terminus. These proteins are mainly involved in RNA splicing, endoplasmic reticulum stress, and a variety of metabolic signaling pathways. Surprisingly, MS results reveal that EspF can also phosphorylate H2AX, suggesting that EspF may directly mediate DNA damage. Here, by western blot and immunofluorescence (IF), we verified that EspF can cause phosphorylation of H2AX and mediates cell multi-nuclearation and cell hypertrophy. Furthermore, we verify here for the first time that SMC1 interacts with EspF -C-terminus, and provide evidence that EspF increases p-SMC1 levels. p-SMC1 is known to influence S-phase cell cycle arrest and usually increases during periods of DNA damage. Our work revealed a novel interaction between EspF and the host protein SMC1 and lays a foundation for further research on EspF-mediated host DNA damage, apoptosis, and even colorectal carcinogenesis.

A Fall armyworm (FAW) is a major pest of maize and causes huge losses. Chemical control is the commonly used strategy FAW among farmers. Efficacy of baculovirus against FAW has been proven, however, farmers may not afford the products. The use of farmer produced baculovirus mixtures could provide an opportunity for a nature-based solution for FAW at low cost. This study evaluated the potential of virus extracted from FAW larvae treated with a commercial baculovirus (Littovir) for the management of FAW under laboratory and field conditions. In Laboratory, the virus extracted from 25, 50, 75 and 100 FAW larvae caused varied mortality on FAW instars. The highest mortality (45%) on 1st-3rd instars was caused by Littovir followed by virus extract from 100 FAW larvae (36%). Under field conditions, even though virus extracts did not offer adequate protection against the FAW damage, the maize yield was comparable to commercial insecticides treated plots. This study has shown the potential of use of virus extracts for management of FAW. This would offer the farmers a sustainable and affordable option for management of FAW as it would require the farmers to purchase the commercial baculovirus once and collect larvae from treated plots for repeat applications.

With demand for the long-term continued use of existing building facilities, structural health monitoring and damage detection are attracting interest from society. Sensors of various types have been practically applied in the industry to satisfy this need. Among the sensors, piezoelectric sensors are an extremely promising technology by virtue of their cost advantages and durability. Although they have been used in aerospace and civil engineering, their application for building engineering remains limited. Remarkably, recent catastrophic seismic events have further rein-forced the necessity of rapid damage detection and quick judgment about the safe use of facilities. Faced with these circumstances, this study was conducted to assess the applicability of piezoelectric sensors to evaluate building components. Specifically, this study emphasizes structural damage caused by earthquakes. After first applying to cyclic loading tests to composite beam component specimens and steel frame subassemblies with a folded roof plate, the prospective damage posi-tions were also found using finite element analysis. Crack propagation and buckling locations were predicted adequately. The piezoelectric sensors provided output when the concrete slab showed tensile cracks, or when the folded roof plate experienced local buckling. Furthermore, damage expansion and progression were detected multiple times during loading tests. Results showed that the piezoelectric sensors can detect structural damage of building components, demonstrating their potential for use in inexpensive and stable monitoring systems.

There are few results about the internal damping ratio of normal and high strength concretes. Hence, this paper presents the expansion of the investigation about internal damping ratio under undamaged and damaged conditions, for usual concretes (NSC) and high strength concretes (HSC). In this way, the study cover a strength range of 42 to 83 MPa. Cyclic load was employed by a servo-controlled hydraulic testing machine and for each cyclic step the dynamic elastic modulus (Ed) and internal damping ratio (ξ) were determinate by acoustic tests. Normal strength concretes (fc = 42MPa) presented undamaged internal damping ratio ξ = 0.5% and achieved the maximum value of ξ = 2.5 for a damage index equal to 0.8. High strength concretes mixtures (fc = 83MPa) presented an undamaged internal damping of ξ=0.29% and maximum internal damping equal to ξ=0.93% (under damage index of 0.32). Porosity and the transition zones were the responsible to the initial internal damping values and how the material behavior under each cyclic load. The progressive damage generates the increase of coulomb damping. There are few studies allowing the quantification and comprehension of internal damping ratio under damage cyclic loading and this approach will lead to improve the understanding of NSC and HSC under dynamical excitation subject to damage evolution, mainly in impact situations.

To achieve sustainable development during urbanization, construction waste is recycled for use as an aggregate in recycled concrete (RC). To determine the influence of the brick content in coarse recycled aggregates on the damage sustained by the resultant RC, the RC was first divided into seven phases: natural crushed stone, old gravel inside waste concrete, bricks, new mortar, old mortar on waste concrete surfaces, and new and old interface transition zones. The Monte Carlo method was then applied to establish a two-dimensional random aggregate model of the RC made with coarse brick aggregates. The ABAQUS software package was used to simulate a uniaxial compression test, the results of which were combined with those of a macro-test to determine the internal damage change rule of brick-containing RC. The stress–strain curves obtained from the simulation coincided well with that of the macroscopic tests. As the brick content increased, the damage zone inside the specimen and the number of microcracks increased. The stress concentration area decreased, as indicated by a lower compressive strength in the macro-test. The results indicate that higher brick contents in RC yield more initial damage inside the concrete and a lower compressive strength.

Understanding and predicting damage progression within thin plain-woven CFRP components is an essential issue for scheduling maintenance intervals and structural inspections, and typically require extensive test series. However, uncertainties always remain and result in conservative design and unnecessary downtimes due to the repeated inspections of a healthy structure. SHM can be used to reduce these uncertainties, as it allows to evaluate the condition of a mechanical structure during operation. Numerous SHM methods are developed , that achieve different levels of damage identification but are often investigated at small coupons with non-realistic structural damages and loading conditions on both, structure and sensor. The present research investigates the electrical impedance tomography (EIT) featuring an elastoresistive thin-film sensor to evaluate damage that propagates from a circular hole in a large plate under cyclic tensile-tensile multi-block loading. Applied fatigue loads were increased multiple times up to a total number of two million cycles. During the loading damage initiated at the hole and continuously propagated into the plate. Repeated EIT evaluations of the applied sensor and validating evaluations by means of digital image correlation clearly revealed the robustness of the hardware and the potential of the SHM method for damage evaluation of plain-woven CFRP components.