This work communicates a review on Balmer series hydrogen beta line measurements and applications for analysis of white dwarf stars. Laser-induced plasma investigations explore electron density and temperature ranges comparable to white dwarf star signatures such as Sirius B, the companion to the brightest star observable from the earth. Spectral line shape characteristics of the hydrogen beta line include width, peak separation, and central dip-shift, thereby providing three indicators for electron density measurements. The hydrogen alpha line shows two primary line-profile parameters for electron density determination, namely, width and shift. Both Boltzmann plot and line-to-continuum ratios yield temperature. The line-shifts recorded with temporally- and spatially- resolved optical emission spectroscopy of hydrogen plasma in laboratory settings can be larger than gravitational redshifts that occur in absorption spectra from radiating white dwarfs. Published astrophysical spectra display significantly diminished Stark or pressure broadening contributions to red-shifted atomic lines. Gravitational redshifts allow one to assess the ratio of mass and radius of these stars, and subsequently, the mass from cooling models.

The analysis of suspended particle size distribution in produced water for hydraulic fracturing and for water injection operations is vital for the effective development of tight reservoir formations like the Middle Bakken. Several reservoir engineering studies and industry guidelines recommend that particle sizes fall between 1/7th and 1/3rd of the square root of the formation permeability measured in millidarcies, to avoid pore throat clogging and subsequent formation damage. In the tight Bakken formation, with an average permeability of 0.04 millidarcies, the ideal particle size range for total suspended solids should fall within the 0.03 to 0.06 microns range. This study evaluates whether produced water used for hydraulic fracturing and enhanced oil recovery in the Middle Bakken meets this recommendation, as there are no established regulations in North Dakota addressing this issue. Using laser diffraction, particle size distribution was measured in treated and untreated produced water samples. The results show that current treatment methods do not reduce particle sizes to the recommended range. Treated water had particle diameters ranging from 8.5 to 40 μm, while untreated water had diameters ranging from 8.2 to 10 μm. None of the samples met the particle size requirements for safe use in hydraulic fracturing and water injection. This study highlights the inadequacy of current water recycling practices and offers empirical evidence that may guide future regulations on produced water reuse hydraulic fracturing and water injection in the Bakken.

Monte Carlo techniques have been extensively used for planning laser-based clinical procedures such as photobiomodulation. However, the effect of several biological tissue characteristics, including morphological structure and physiological parameters, has not been carefully addressed in many applications. Specifically, many questions remain concerning the effect of skin phototype and body mass index on the efficacy of photobiomodulation for extraoral therapies. To address these questions, a Monte Carlo simulation model was developed to analyze the effects of body mass index-dependent skin structure and Fitzpatrick skin type, specifically tailored for the morphological characteristics of cheek tissue. The model describes the settings of a typical oral photobiomodulation treatment protocol for pain relief, namely the use of 660 nm and 808 nm laser wavelengths and a therapeutic dose of 2.0 J/cm² on the masseter muscle. The simulations were used to train a machine learning predictive model aimed at accelerating the treatment planning stage and assessing the importance of patient-specific parameters. A multiple regression approach was adopted to predict muscle dose and treatment time for the effective delivered dose.

In this study, the NiCrAlY coating was prepared using the atmospheric plasma spraying (APS). The sample was then exposed to a continuous fiber laser beam. Laser surface melting (LSM) can effectively homogenize the composition of the coating. It also reduced the defects and roughness. The coating was examined using optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. The process parameters of the LSM consist of laser power and scan rate. The high-temperature oxidation test was conducted for 200 hours at a temperature of 1100 °C. After a period of 200 hours, the primary coating demonstrated the emergence of an aluminum oxide layer, along with the presence of harmful spinel oxides. The laser remelting technique was used to modify the surface, which led to the uniform growth and development of an aluminum oxide layer (α-Al₂O₃) during the oxidation examination. Therefore, it appears that the reduction in grain size caused by laser remelting prevents the wrinkling of Al2O3 oxide. This process represents a novel and alternative approach to modifying MCrAlY coatings.

Several Lung diseases can result in lung damage structural changes, with lung transplantation as a only therapeutic option when the disease reaches an advanced progression, unfortunately, the success of lung transplantation is limited. In this context, lung bioengineering is considered a potential therapeutic alternative and the current approach is based on the use of the natural extracellular matrix (ECM) of the decellularized lung. The use of undifferentiated cells to seed an ECM can be a more practical strategy for lung bioengineering but the sterilization of the organ for this recellularization process is still a challenge. In this sense, Low-Level Laser Therapy (LLLT) can emerge as a potential treatment alternative. Therefore, the objective of this study was to verify if LLLT, can optimize lung recelularization with mesenchymal stem cells by cytokine modulation. For this, we decellularized lungs from C57BL/6 mice perfusing SDS 1% via pulmonary artery, sterilized with LLL (660nm, 100mW, 30s). Whole lung scaffolds were recellularized: (1) Recellularized Lung (2) Recellularized Lung + LLLT. Mesenchymal stem cells derived from human tooth pulp (DPSc) were seeded into lungs and incubated for 24 hours at 37ºC, 5% CO₂, in a bioreactor-like conditions, maintaining CPAP at 20cmH2O, 90% O2, and LLL at wavelength of 808nm, 100mW, 30s. Culture medium were analyzed at 24 hours. H&E, immunostaining, SEM and ELISA assay were performed. We produced viable biological scaffolds absent of DNA content, preserving glycosaminoglycans and collagen I, III and IV, fibronectin, laminin and elastin and lung structure (SEM). The levels of IL-6 and IL-8 were stable during the 24 hours of culture. IFN-γ levels showed significant difference in the DPSc and DPSc+LLLT group in the 24-hour evaluation. The levels of IL-10 decreased after LLLT. These findings highlight LLLT's role in cytokine regulation and contamination prevention during lung recellularization with mesenchymal stem cells. Overall, these results demonstrated that LLLT's modulated cytokine levels and could prevent contamination during the lung recellularization process with mesenchymal stem cells, offering promise for enhanced therapeutic strategies in lung bioengineering.

This paper proposes a solution for the problem of mobile robot navigation and trajectory interpolation in dynamic environments with large scenes. The solution combines a semantic laser SLAM system that utilizes deep learning and a trajectory interpolation algorithm. The paper first introduces some open-source laser SLAM algorithms and then elaborates in detail on the general framework of the SLAM system used in this paper. Secondly, the concept of voxel is introduced into the occupation probability map to enhance the ability of local voxel maps to represent dynamic objects. Then, in this paper, we propose a PointNet++ point cloud semantic segmentation network combined with deep learning algorithms to extract deep features of dynamic point clouds in large scenes and output semantic information of points on static objects. A descriptor of the global environment is generated based on its semantic information. Closed-loop completion of global map optimization is performed to reduce cumulative error. Finally, T-trajectory interpolation is utilized to ensure the motion performance of the robot and improve the smooth stability of the robot trajectory. The experimental results indicate that the combination of the semantic laser SLAM system with deep learning and the trajectory interpolation algorithm proposed in this paper yields better graph building and loop closure effects in large scenes at SIASUN large scene campus. The use of T-trajectory interpolation ensures vibration-free and stable transitions between target points.

In order to improve the wear resistance of copper contacts in high-voltage switches and improve the abnormal discharge phenomenon caused by wear gaps, laser remelting technology was used to strengthen the surface of copper contacts. The surface morphology, microhardness, and wear resistance of the remelted samples were tested and characterized using scanning electron microscopy (SEM), microhardness tester, and friction and wear tester. The test results indicate that laser frequency, pulse width, and current parameters can directly affect the surface morphology and wear resistance of the sample, but their influencing processes vary. The laser frequency is achieved by the variation of the superposition relationship between the impact points, while the pulse width and current are achieved by the variation of the laser intensity at the impact points. When the pulse frequency is 10Hz, the pulse width is 10ms, and the current is 100A, the sample exhibits a more balanced surface morphology, microhardness, and wear resistance.

We investigate the production of an isolated attosecond pulse (IAP) via the phase-matching gating of high-harmonic generation by intense laser pulses. Our study is based on the integration of the propagation equation for the fundamental and generated fields with nonlinear polarisation found via the numerical solution of the time-dependent Schr\"odinger equation. We study the XUV energy as a function of the propagation distance (or the medium density) and find that the onset of the IAP production corresponds to the change from linear to quadratic dependence of this energy on the propagation distance (or density). Finally, we show that the upper limit of the fundamental pulse duration for which the IAP generation is feasible is defined by the temporal spreading of the fundamental pulse during the propagation. This nonlinear spreading is defined by the difference of the group velocities for the neutral and photoionised medium.

It was for long time believed that lidar systems based on the use of high-repetition micro-pulse lasers could be effectively used to only stimulate atmospheric elastic backscatter echoes, and thus only exploited in elastic backscatter lidar systems. Their application to stimulate rotational and roto-vibrational Raman echoes, and consequently their exploitation in atmospheric thermodynamic profiling, was considered not feasible based on the technical specifications possessed by these laser sources until a few years ago. However, recent technological advances in the design and development of micro-pulse lasers, presently achieving high UV average powers (1-5 W) and small divergences (0.3-0.5 mrad), in combination with the use of large aperture telescopes (0.3-0.4 m diameter primary mirrors), allow to presently develop micro-pulse laser-based Raman lidars capable to measure the vertical profiles of atmospheric thermodynamic parameters, namely water vapour and temperature, both in daytime and nighttime. This paper is aimed at demonstrating the feasibility of these measurements and at illustrating and discussing the high achievable performance level, with a specific focus on water vapour profile measurements. The technical solutions identified in the design of the lidar system and their technological implementation within the experimental setup of the lidar prototype are also carefully illustrated and discussed.

Ovarian endometriomas have a negative impact on a patient’s reproductive potential and likely cause a reduction in ovarian reserve. The most commonly employed ovarian reserve parameters are anti-mullerian hormone (AMH) and antral follicular count (AFC). Surgical management options of endometrioma include cystectomy, ablative methods, ethanol sclerotherapy and combined techniques. The optimal surgical approach remains a matter of debate. Our review aimed to summarize the literature on the impact of surgical management of endometrioma on AMH, AFC and fertility outcomes. Cystectomy may reduce recurrence rates and increase chances of spontaneous conception. However, a post-operative reduction in AMH is to be anticipated, albeit there is evidence of recovery during follow-up. The reduction in ovarian reserve is likely multi-factorial. Cystectomy does not appear to significantly reduce, and may even increase, AFC. Ablative methods achieve an ovarian tissue-sparing effect and improved ovarian reserve, compared to cystectomy, has been demonstrated. A single study reported on AMH and AFC post- sclerotherapy and both were significantly reduced. AMH levels may be useful in predicting the chances of conception post-operatively. None of the aforementioned approaches has clearly demonstrated a superiority in terms of overall chances of conception. Surgical management of endometrioma may, overall, improve probability of pregnancy. Evidence on its value before medically-assisted reproduction (MAR) is conflicting, however, a combination of surgery followed by MAR may achieve the optimal fertility outcome. In view of the complexity of available evidence, individualisation of care, combined with optimal surgical technique, is highly recommended.

The choice of parameters for laser beams used in the treatment of musculoskeletal diseases is of great importance. First, to reach high penetration depths into biological tissue and, secondly, to achieve the required effects on a molecular level. The penetration depth depends on the wavelength since there are multiple light-absorbing and scattering molecules in tissue with different absorption spectra. The present study is the first comparing the penetration depth of 1064 nm laser light with light of a smaller wavelength (905 nm) using high-fidelity laser measurement technology. Penetration depths in two types of tissue (porcine skin and bovine muscle) were investigated. The transmittance of 1064 nm light through both tissue types was consistently higher than of 905 nm light. The largest differences (up to 5.9%) were seen in the upper 10 mm of tissue, while the difference vanished with increasing tissue thickness. The higher penetration was most likely due to a combination of lower absorption in hemoglobin and less scattering at larger wavelengths, and not due to absorption in melanin. Overall, differences in penetration depth were comparably small and high peak power and short pulse lengths of laser light seem to be more important to efficiently treat deep musculoskeletal diseases.

Microlens arrays (MLAs) which are increasingly popular micro-optical elements in compact integrated optical systems were fabricated by femtosecond direct laser write (fs-DLW) technique in the low-shrinkage SZ2080TM photoresist. High fidelity definition of 3D surfaces on IR transparent CaF2 substrates allowed to achieve ∼ 50% transmittance at chemical fingerprinting spectral region 2-5 μm wavelengths since MLAs were only ∼ 10 μm high corresponding to the numerical aperture of 0.3 (the lens height is comparable with the IR wavelength). To combine diffractive and refractive capabilities in miniaturised optical setup, a graphene oxide (GO) grating acting as a linear polariser was also fabricated by fs-DLW by ablation of a 1 μm-thick GO thin film. Such an ultra-thin GO polariser can be integrated with the fabricated MLA to add dispersion control at the focal plane. Pairs of MLAs and GO polarisers were characterised throughout visible-IR spectral window and numerical modeling was used to simulate their performance. Good match between experimental results of MLA focusing and simulations was achieved.

Modifiable THz spectral shapes are important tools that facilitate the comprehensive study of phonon dynamics in condensed matter systems. The generation of narrow bandwidth THz spectra with tunable center frequency which are suitable THz forms needed to achieve such objectives are currently less studied from the table top laser-induced plasma emitters’ perspective. This experimental research is aimed at developing a robust two-color laser induced plasma set-up comprising of a temporal pulse stretcher and an Optical Parametric Amplifier that generates chirped and wavelength tunable pulses respectively. By focusing and independently controlling the ω and 2ω arms of the chirped pulses resulting after the interaction with a β-BBO crystal, I aim to generate narrow bandwidth THz signal (from plasma) scalable at MV/cm intensity and tunable in a wide THz spectral range, in addition to varying the frequency ratio mix.

Laser patterning of implant materials for bone tissue engineering purposes has shown to be a promising technique to control cell properties such as adhesion or differentiation, resulting in an enhanced osteointegration. However, the perspective of patterning the bone tissue side interface to generate microstructure effects has never been investigated. In the present study, three different laser-generated patterns were machined on the bone surface with the aim to identify the best surface morphology compatible with osteogenic-related cells recolonization. The laser patterned bone tissue was characterized by electron scanning microscopy and confocal microscopy in order to obtain a comprehensive picture of the bone surface morphology. Cortical bone patterning impact upon cell compatibility and cytoskeleton rearrangement to the patterned surfaces was performed with Stromal Cells from Apical Papilla (SCAPs). Results indicated that laser machining had no detrimental effect upon consecutively seeded cells metabolism. Orientation assays revealed that surface patterning characterized by larger hatch distances was correlated with a higher cell cytoskeletal conformation to the laser-machined patterns. For the first time, to our knowledge, bone is considered and assessed here as a potentially engineered-improvable biological interface. Further studies shall focus on in vivo implications of this direct patterning.

This paper develops the study of the effect of powerful ultrasound on the laser breakdown of liquids and a comparative study of the possibilities of acoustic and optical diagnostics of breakdown. The method of laser-induced breakdown spectroscopy (LIBS) for elemental analysis of liquids, along with high efficiency, continues to be less sensitive compared to traditional chemical methods. The paper develops a method of using additional ultrasound irradiation of the laser breakdown area in order to increase the efficiency of LIBS. Using the developed technique, spectral lines of chemical elements such as potassium, manganese, sodium, calcium, etc. were obtained for the first time depending on the frequency and power of ultrasound. It is shown that a sharp increase in the intensity of spectral lines of elements in water during laser breakdown is observed in the field of high-power ultrasound. It indicates an increase in the sensitivity of the combined method of ultrasonic LIBS. Along with the optical spectrum, the spectral and energy characteristics of acoustic emission were studied. An automated complex for hydrophysical and spectral studies is described, which was tested in the Sea of Japan during the voyage No. 81 of the research vessel RV "Professor Gagarinsky" in August 2022.

We present a compact polarimeter for 3He ions with special emphasis on the analysis of short-pulsed beams accelerated during laser-plasma interactions. We discuss the specific boundary conditions for the polarimeter, such as the properties of laser-driven ion beams, the selection of the polarization-sensitive reaction in the polarimeter, the representation of the analyzing-power contour map, the choice of the detector material used for particle identification, as well as the production procedure of the required deuterated foil-targets. The assembled polarimeter has been tested using a tandem accelerator delivering unpolarized 3He ion beams, demonstrating good performance in the few-MeV range. The statistical accuracy and the deduced figure-of-merit of the polarimetry are discussed, including the count-rate requirement and the lower limit of accuracy for beam-polarization measurements at a laser-based ion source.

Magnetorheological processing was applied to polish the working surfaces of the ZnGeP2 single crystal, in which a non-aqueous liquid with magnetic particles of carbonyl iron with the addition of nanodiamonds was used. Samples of a single crystal ZnGeP2 with an angstrom level of surface roughness were received. the use of MRP has allowed more accurately characterizing possible structural defects that have emerged on the surface of a single crystal and have a size of ~ 0.5-1.5 μm. the LIDT value at the indicated or-ders of magnitude of the surface roughness parameters is determined not by the quality of polishing, but by the number of point depressions caused by physical limitations of the structural configuration of the crystal volume. These results are in good agreement with the assumption made about a significant effect of the concentration of dislocations in a ZnGeP2 crystal on LIDT.

ATLID (ATmospheric LIDar) is the atmospheric backscatter LIDAR (Light Detection and Ranging) on board of the EarthCARE (Earth Cloud, Aerosol and Radiation Explorer) mission, the sixth Earth Explorer Mission of the ESA (European Space Agency) Living Planet Programme [1-5]. ATLID’s purpose is to provide vertical profiles of optically thin cloud and aerosol layers, as well as the altitude of cloud boundaries [6-10]. In order to achieve this objective ATLID emits short duration laser pulses in the UV, at a repetition rate of 51 Hz, while pointing in a near nadir direction along track of the satellite trajectory. The atmospheric backscatter signal is then collected by its 620 mm aperture telescope, filtered through the optics of the instrument focal plane assembly, in order to separate and measure the atmospheric Mie and Rayleigh scattering signals. With the completion of the full instrument assembly in 2019, ATLID has been subjected to an ambient performance test campaign, followed by a successful environmental qualification test campaign, including performance calibration and characterization in thermal vacuum conditions. In this paper the design and operational principle of ATLID is recalled and the major performance test results are presented, addressing the main key receiver and emitter characteristics. Finally, the estimated instrument, in-orbit, flight predictions are presented; these indicate compliance of the ALTID instrument performance against its specification and that it will meet its mission science objectives for the EarthCARE mission, to be launched in 2023.

Surface treatments of metals based on laser marking technology is an important application in a wide range of industrial fields. By specific combinations of laser processing parameters, the modified surface leads to different textures with specific roughness and colored appearance. Most of current works are focused on the modification of color tonality of flat surfaces, or the development of specific topography features, but the combination of both processes is not usually evaluated, mainly due to the complexity to control the optical properties on rough surfaces. This research presents an analysis of the influence of the micro-geometrical characteristics of periodic patterned laser tracks on the chromaticity and reflectance of Ti6Al4V substrates. The samples were irradiated with an infrared nanosecond pulsed laser under air atmosphere, taking as control parameter the scan speed of the beam. A roughness evaluation, microscopic inspection, absorption and chromaticity examination were conducted. Although micro-crack growth was detected in isolated case (10 mm/s), the possibility of adjusting the result color were demonstrated by controlling the thermal affected zone thickness of the textures. Results of rough/colored combined textures allow opening new perspectives in industrial design, particularly in aesthetic applications with special properties.

The present work is a theoretical and experimental study of temperature effect on wavelength and threshold current. Since Semiconductor lasers are the type of lasers which uses semiconductor material as a gain medium to achieve stimulated emission of radiation. In this module, the type of semiconductor lasers use is VCSEL and laser diode. Temperature change cause Semiconductor lasers to shift its threshold current, this variation also causes a shift in output wavelength. The experimental results highly agreement with the theoretical calculations.

We report the production of metal oxide (TiFe₂O₄, ZnFe₂O₄) nanoparticles by pulsed laser ablation technique in liquid environment. We used nano second Nd: YAG laser systems working at 532 nm and 1064 nm of wavelength, the energy of the laser beam was kept constant at 80 mJ. Absorbance spectra, surface plasmon resonance, optical band-gap and nanoparticle morphology were investigated using ultraviolet-visible (UV-Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Changing the wavelength of the laser for growth, nanoparticles shown shift between the absorbance and surface plasmon resonance peaks in their UV-Vis spectra, this implies that the optical properties of the colloid nanoparticles depends on laser parameters, this was confirmed with the variation of the band gap energy. Furthermore, red shift for the absorbance peak was observed for samples as-growth at 532 nm around the 150 nm as function of time preparation. Whereas, for the samples as-growth at 1064 nm there is no shift in the absorbance spectra, this can be due to agglomeration and formation of larger particles. The characterization results shown appropriate plasmonic photo-catalysts properties of the particles, hence the photo activation of the nanoparticles was examined on antibacterial effect using colonies of Staphylococcus Aureus and Escherichia coli.

Laser Cladding is one of the leading processes within Additive Manufacturing technologies, a fact which has concentrated an important amount of effort on its development. In regard to the latter, the current study aims to summarize the influence of the most relevant process parameters in the laser cladding processing of single and compound volumes (solid forms) made from AISI 316L stainless steel powders and using a coaxial nozzle for deposition. Process speed, applied laser power and powder flow are considered to be the main variables affecting laser cladding in single clads, meanwhile overlap percentage and overlapping strategy become also relevant when dealing with multiple clads. By means of setting appropriate values of each process parameter, the main goal of this paper is to develop a processing window in which a good metallurgical bond between the delivered powder and substrate is obtained, trying simultaneously to maintain processing times in their lowest value possible. Conventional metallography techniques were performed on the cross sections of the laser tracks to measure the effective dimensions of clads for dilution analysis, height and width for the values of overlap between contiguous clads and layers, and also to analyze them for physical defects such as porosity and cracks. The resulting solid piece was 8 mm high at 800 mm/min.

The article presents tests aimed to verify the possibility of making T-joints in TMCP steel using laser. The tests involved the use of 10 mm thick high yield point steel S700MC obtained in an industrial manufacturing process. The joints made in the tests were single and double-sided. Subsequent non-destructive tests revealed that the joints obtained in the tests represented quality level B in accordance with PN-EN ISO 13919-1. Single-sided welding performed using the laser beam having a power of 11 kW enabled the obtainment of 8 mm deep penetration without visibly deforming the web of the joint. The double-sided welded joints were characterised by proper geometry and the presence of gas pores in the welds not compromising the requirements of quality level B (strict requirements). The weld structure was bainitic-ferritic. The weld hardness was by approximately 60 HV1 higher than that of the base material (280 HV1). The HAZ area was slightly softer than the base material. The tests of thin foils performed using a high-resolution scanning transmission electron microscope revealed that, during welding, an increase in the content of the base material in the weld was accompanied by an increase in contents of alloying microagents Ti and Nb, particularly near the fusion line. The above-named alloying microagents, in the form of fine-dispersive (Ti,Nb)(C,N) type precipitates, could reduce plastic properties of joints.

Porous graphite was prepared without the use of template by rapidly heating the carbonization products from mixtures of anthracene, flourene, and pyrene with a CO₂ laser. Rapid CO₂ laser heating at a rate of 1.8 × 10 ⁶ °C/s vaporizes out the fluorene-pyrene derived pitch while annealing the anthracene coke. The resulting structure is that of graphite with 100 nm spherical pores. The graphitizablity of the porous material is the same as pure anthracene coke. Transmission electron microscopy revealed that the interface between graphitic layers and the pore walls are unimpeded. Traditional furnace annealing does not result in the porous structure as the heating rates are too slow to vaporize out the pitch, thereby illustrating the advantage of fast thermal processing. The resultant porous graphite was prelithiated and used as an anode in lithium ion capacitors. The porous graphite when lithiated had a specific capacity of 200 mAh/g at 100 mA/g. The assembled lithium ion capacitor demonstrated an energy density as high as 75 Wh/kg when cycled between 2.2 V to 4.2 V.

Recent researches proved that the underbridge geometry can be reconstructed by mounting a 3D laser scanner on a motorized cart travelling on a walkway located under the bridge. The walkway is moved by a truck and the accuracy of the bridge model depends on the accuracy of the trajectory of the scanning head with respect to a fixed reference system. In this paper, we describe the metrological characterization of a method that uses non-contact systems to identify the relative motion of the cart with respect to the walkway; the orientation of the walkway with respect to the bridge is determined using inclinometers and optical rails, while the position of the truck with respect to the bridge is measured using a conventional odometer. The measurement uncertainty of the proposed system was initially evaluated by numerical simulations and successively verified by experiments in laboratory conditions. The complete system has then been tested in operative conditions; the validity of the proposed approach has been demonstrated by comparing the geometry of buildings reconstructed with the proposed system with the geometry obtained with a static scan. Results evidenced that the errors are approximately 6 mm.

Background: The prevalence of atopic dermatitis in domestic animals is one of the problems of modern veterinary. Treating with standard techniques using chemotherapeutic agents not always leads to a positive result of therapy; moreover, many drugs produce adverse side effects. Methods: Low level laser therapy, in particular, intravenous laser blood illumination (ILBI) has a pronounced and long-lasting impact on the immune system of animals. The combined technique including ILBI-635 (635 nm, 2 mW, 5 min) and LUVBI^® (365 nm, 2 mW, 3 min) every other day provides a positive change in clinical status of cats with allergic dermatitis after the 3rd-4th treatment session. Results: The increased level of erythrocytes and hemoglobin was identified in the course of treatment, and it indirectly indicates increased blood transport activity, which improves trophic provision and microcirculation. A double reduction of leukocytes and a significant decrease of neutrophil cells indicate the immunomodulatory effect of LILI (low-intensity laser illumination). The increase in the percentage of lymphocytes and the decrease of eosinophils and monocytes against the background of basophil concentrations deviations within physiological concentration result in the reduction of inflammatory mediators expression that induce itching. The reduction of total IgE concentration 32 times against control on the 7th day of treatment correlates with the decrease in the quantitative content of peripheral blood eosinophils, indicating the decrease in severity of an allergic process. Conclusion: LLLT is recommended against the background of standard drug therapy to achieve quick clinical outcome together with a long-lasting prolonged effect.

Here, we report on ZnO nanoparticles (NPs) generated by nanosecond pulsed laser (Nd:YAG, 1064 nm) through ablation of metallic Zn target in water and air and their comparative analysis as potential nanomaterials for biomedical applications. The prepared nanomaterials were carefully characterized in terms of their structure, composition, morphology and defects. It was found that in addition to the main wurtzite ZnO phase, which is conventionally prepared and reported by others, the sample laser-generated in air also contained some amount of monoclinic zinc hydroxynitrate. Both nanomaterials were then used to modify model wound dressings based on biodegradable poly-L-lactic acid. The as-prepared model dressings were tested as biomedical materials with bactericidal properties towards S. aureus and E. coli strains. The advantages of the NPs prepared in air over their counterparts generated in water found in this work are discussed.

Laser scanning 3D imaging technology, because it can get accurate three-dimensional surface data, has been widely used in the search for wrecks and rescue operations, underwater resource development, and other fields. At present, the conventional underwater rotating laser scanning imaging system maintains a relatively fixed light window. However, in low-light situations underwater, the rotation of the scanning device causes some degree of water fluctuation, which warps the light strip data that the system sensor receives about the object's surface. To solve the problem, this research studies an underwater 3D scanning and imaging system that makes use of a fixed-light window and a spinning laser (FWLS). A refraction error compensation algorithm is investigated that is based on the fundamentals of linear laser scanning imaging and the dynamic refraction mathematical model is established by the motion of the imaging device. During the imaging process, the incident angle between the laser and the light window varies due to the scanning mode of the system. The experimental results show that the reconstruction radius error is reduced by 60% (from 2.5 mm to about 1 mm) when the measurement data for a standard sphere with a radius of 20 mm are compensated. Moreover, the compensated point cloud data exhibits a higher degree of correspondence with the model of the standard spherical point cloud. This study has a specific reference value for the refractive error analysis of an underwater laser scanning imaging system, and it provides certain research ideas for the subsequent refractive error analysis of various scanning imaging modalities.

Laser energy per unit surface, necessary to trigger the material removal, decreases with the pulse shortening becoming the pulse-time independent in the sub-picosecond range. These pulses are shorter the electron-to-ion energy transfer time and electronic heat conduction time minimizing the energy losses. The electrons receiving the energy larger than the threshold, drag the ions off the surface in the mode of electrostatic ablation. We show that the pulse shorter than the ion period (Shorter-the-Limit (StL)) ejects conduction electrons with the energy larger than the work function (from a metal) leaving the bare ions immobile in a few atomic layers. The electrons emission is followed by the bare ion’s explosion, ablation, and THz radiation from expanding plasma. We compare this phenomenon to the classic photo effect, nanocluster Coulomb explosions, show differences and consider possibilities for detecting the new mode of ablation experimentally by emitted THz radiation and consider applications of high-precision nano-machining with this low intensity irradiation.

This work discusses diatomic molecular spectroscopy of laser-induced plasma and analysis of data records, specifically signatures of cyanide, CN. Line strength data from various databases are compared for simulation of the CN, B2Σ+⟶X2Σ+, Δv=0 sequence. Of interest are recent predictions using an astrophysical database, i.e., ExoMol, a laser-induced fluorescence database, i.e., LIFBASE, and a program for simulating rotational, vibrational and electronic spectra, i.e., PGOPHER. Cyanide spectra that are predicted from these databases are compared with line strength data that are in use by the author for the last three decades in the analysis of laser-plasma emission spectra. Comparisons with experimental laser-plasma records are communicated as well, and for spectral resolutions of 33 and 110 picometer. The accuracy of the CN line strength data is better than one picometer. Laboratory experiments utilize 308-nm, 35-picosecond bursts within an overall 1-nanosecond pulse-width, and 1064-nm, 6-ns pulse-width radiation. Experimental results are compared with predictions. Differences of the databases are elaborated for equilibrium of rotational and vibrational modes and at an internal, molecular temperature of the order of 8,000 Kelvin. Applications of accurate CN data include for example combustion diagnosis, chemistry, and supersonic and hypersonic expansion diagnosis. The cyanide molecule is also of interest in the study of astrophysical phenomena.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

This article reports new measurements of laser-induced plasma hypersonic expansion measurements of diatomic molecular cyanide (CN). Focused, high-peak power 1064-nm Q-switched radiation of the order of 1 TW/cm² generates optical breakdown plasma in a cell containing a 1:1 molar gas mixture of N₂ and CO₂ at a fixed pressure of 1.1 × 10⁵ Pascal and in a 100 ml/min flow of the mixture. Line-of-sight (LOS) analysis of recorded molecular spectra indicate the outgoing shockwave at expansion speeds well in excess of Mach number 5. Spectra of atomic carbon confirm an increased electron density near the shock wave, and equally, molecular CN spectra reveal higher excitation temperature near the shockwave. The results are consistent with corresponding high-speed shadow graphs obtained by visualization with an effective shutter speed of five n anosecond. In addition, LOS analysis and application of integral inversion techniques allow inferences about the spatio-temporal distribution of the plasma.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

3D meso-scale structures that can reach up to centimeters in overall size but retain micro- or nano-features, proved to be promising in various science fields ranging from micro-mechanical metamaterials to photonics and bio-medical scaffolds. In this work we present synchronization of the linear and galvano scanners for efficient femtosecond 3D optical printing of objects at the meso-scale (from sub-μm to sub-cm spanning five orders of magnitude). In such configuration the linear stages provide stitch-free structuring at nearly limitless (up to tens-of-cm) working area, while galvo-scanners allow to achieve translation velocities in the range of mm/s-cm/s without sacrificing nano-scale positioning accuracy and preserving undistorted shape of the final print. The principle behind this approach is demonstrated, proving its inherent advantages in comparison to separate use of only linear stages or scanners. The printing rate is calculated in terms voxels/s, showcasing the capability to maintain an optimal feature size while increasing throughput. Full capabilities of this approach are demonstrated by fabricating structures that reach millimeters in size but still retain μm-scale features: scaffolds for cell growth, microlenses and photonic crystals. All this is combined into a benchmark structure: a meso-butterfly. Provided results show that synchronization of two scan modes is crucial for the end goal of industrial-scale implementation of this technology and makes the laser printing well aligned with similar approaches in nanofabrication by electron and ion beams.

The interaction of pulsed lasers with matter involving nanomaterials as a pure target or thin layer deposited on a target, initiates transient plasma which shows strong enhancement in a spectral line emission. This domain of research has been explored via two well established techniques dubbed NELIBS and NELIPS. These Nano-Enhanced Laser Induced Breakdown or Plasma Spectroscopy techniques entail similarities as well as differences. Thereupon, certain confusion has arisen from various aspects of the similarities as well as differences between the two techniques. In this article, we will investigate the application of either technique to retrieve relevant data about enhanced spectral line plasma emission phenomenon. To discriminate between these two techniques, survey on the nature of target, the origin of enhancement and prevalent theoretical approaches is presented. Finally, potential achievements, challenges, and the expected prospective are highlighted.

In this study, we demonstrate a proof of principle of an all-fiber random laser due to the plasmonic effect. This was achieved in a fiber co-doped with Bismuth/Aluminum/Yttria/Silver in which a microsphere (microcavity) at the fiber’s tip was made using a splicing machine. The presence in the fiber of Bismuth- and silver nanoparticles along with Bismuth-Aluminum phototropic centers stands behind the observed phenomenon. The effect can be attributed to in-pair functioning of this unit as an active medium and volumetric plasmonic feedback, with the result being lasing at 807 nm under 532-nm pumping with notably low (~2 mW) threshold.

Knee osteoarthritis (KO) is an important health condition, affecting one third of the people aged 65 years or more. Pain is the main cause of disability. Pain management in KO includes pharmacological and non-pharmacological modalities. Patient education, lifestyle changes, physical exercise and physical agents are prescribed as a first approach for pain control. Laser therapy is part of many therapeutical protocols, with two forms, low-level laser therapy (LLLT) and high-intensity laser therapy (HILT). The paper aimed at stressing the advantages of HILT, based on a greater wavelength, higher energy delivery and deeper tissue penetration. Research on 23 published trials revealed that analgesic effect is rapid, cumulative and long lasting. Compared to sham, to LLLT or to other associations of therapeutical modalities, HILT provided significantly better results on pain reduction and functional improvement. Ultrasound examination showed reduction of intraarticular inflammation.

Laser-induced fluorescence spectroscopy (LIFS) is actively used for remote sensing of atmospheric aerosols and currently is one of the most sensitive and selective techniques for determining small concentrations of substances inside particles. The use of high-power femtosecond laser sources for LIFS-based remote sensing of aerosol contributes to the development of new-generation fluorescence atmospheric lidars since it makes it possible overcoming the energy threshold for the nonlinear-optical effects of multiphoton absorption in particles and receiving the emission signal at long distances in the atmosphere. Our study is aimed to the development and experimental demonstration the technique of nonlinear laser-induced fluorescence spectroscopy (NLIFS) based on the remote excitation of aerosol fluorescent emission stimulated by a spatially-structured high-power femtosecond laser pulse. Importantly, for the first time to our knowledge, we demonstrate the advances of using stochastically-structured plasma-free intense light channels (postfilaments) specially formed by propagation of femtosecond laser radiation through a turbulent air layer for improving NLIFS efficiency. A multiple increase in the received signal of two-photon-excited fluorescence of polydisperse dyed aqueous aerosol by the structured postfilaments is reported.

Keywords: Vascular Malformation, Diode Laser, Angioma, Blue light, Conservative

This study explores the use of remote ultrasound vibration to enhance welding strength. It examines the effects of 20 kHz, and 40 kHz High Power Ultrasound Transducers (HPUT) in contact and contactless modes during ultrasonic assistance laser welding. Employing shear tests and microscopy for assessment, the research evaluates ultrasound's impact on welding strength and identifies the optimal transducer. Theoretical and numerical analyses investigate vibration transmission into the welding area, particularly examining the vibration distribution and cavitation initiation within the molten pool area. Results indicate that ultrasound-assisted welding increases pull test performance, including the resistance force and strain, and improves microscopic structural integrity. Numerical simulations suggest that narrow-band vibration intensifies pressure in specific welding zones. Contactless ultrasound application also shows enhanced welding quality, offering a promising alternative to current methods. This work contributes to electric car technology by suggesting improvements in welding techniques for power battery systems.

Light detection and ranging (LIDAR) sensors using a polarization-diverse receiver are able to capture polarimetric information about the target under measurement. This information can be used in a classifier to make an instantaneous assessment of the type of material present, enabling a shot-by-shot prediction of the material type and distance to the target.

Background: The validation of laser usage during laparoscopic procedures, notably by Camran Nezhat in the late 1980s, has been significant. Lasers offer precision and depth control in tissue vaporization without bleeding. Surgical intervention remains central in managing endometrio-sis-associated pain and infertility, especially for patients unresponsive to hormonal therapy. Methods: This retrospective cohort study included 200 patients with SPE who underwent laparo-scopic laser vaporization. Surgery was performed using a CO2 laser, and histological confirma-tion of endometriosis was obtained for all cases. Pain scores and SF-36 questionnaire domains were assessed preoperatively and postoperatively. Fertility outcomes were evaluated among pa-tients desiring pregnancy. Results: Significant improvements in pain score and SF-36 questionnaire domains were ob-served postoperatively (p-value

Background: Peripheral Ossifying Fibroma (POF) is a benign gingival tumor generally presenting as a slow-growing mass, usually not ulcerated, and without bleeding. Histopathological exam shows fibrous connective tissue with spots or extensive areas of intralesional calcifications, which can also be detectable on radiograms. Methods and case presentation: We present the case of a 4-year-old male with a retro-incisive swelling of the hard palate, associated with speaking and feeding difficulties. On CT scans, a small intralesional calcification was detected. After conscious sedation, the patient was subjected to diode laser excision (910 nm, 2W, CW, 300 m fiber) with-out post-operative complications. A review was conducted by searching the words “peripheral ossifying fibroma” AND “children” OR “infant” and including manuscripts of the last 15 years. Results: POF is an uncommon lesion of the oral mucosa and may sporadically affect the palatal mucosa in children. Considering its epidemiology and conventional clinical presentation as epu-lis, the pre-operative diagnosis may be relatively difficult. Risk factors could be represented by plaque, calculus, or trauma, all supporting a possible reactive pathogenesis, but a certain etiology is still missing. The main problem of POF is the recurrence rate, which is particularly high (8-20%), thus suggesting that a deep excision is recommended with full extension to the hard tis-sue of bone and to the adjacent periodontal ligament. Diode laser surgery may be recommended for such treatments, especially in pediatric patients, associated with intraoperative conscious se-dation. Data emerging from the relevant literature on POF management in children have been collected and discussed. Conclusions: The authors suggest the use of diode laser for the complete excision of POF, especially in less-compliant patients as children, with a low grade of comorbidi-ties and good outcomes, giving the surgeon a viable alternative to conventional surgery.

Within the spectra of lanthanide atoms quite often overlapping spectral lines (blends) are observed. On the example of complicated blend situations within Pr I and La I it is shown that in such cases a combination of optogalvanic and laser-induced fluorescence detection is necessary to find all transitions contributing to the observed spectral signature.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

Laser powder bed fusion can fabricate porous structure through lattices, but it remains a challenge to prepare micropores (

The COVID-19 pandemic caused by the virus SARS-CoV-2 has been the greatest global threat to human health in the last three years. The most widely used methodologies for the diagnosis of COVID-19 are quantitative reverse transcription polymerase chain reaction (RT-qPCR), used to detect the viral genome, and rapid antigen tests (RATs), also known as lateral flow tests, that employ specific antibodies to detect the viral spike protein. While PCR is considered the gold standard test in terms of specificity and sensitivity, it is time-consuming and requires specialized instrumentation operated by skilled personnel. In contrast, RATs can be used in-home or at point-of care but are less sensitive leading to a higher rate of false negative results. An alternative methodology for the detection of virus is the use of electrochemical biosensors that employ disposable strip electrodes to which binding of viral components elicits a change in electrical signal. Laser-scribed graphene (LSG) electrodes are attractive candidates for use as biosensors electrodes suitable for SARS-COV-2 detection due to their low-cost, patternability and ease of fabrication. In this work, we describe the development of a biosensor for COVID-19 detection that exploits a split-ester bond ligase system (termed ‘EsterLigase’) for immobilization of a virus-specific nanobody to maintain the out-of-plane orientation of the probe to ensure the efficacy of the probe-target recognition process. An anti-spike VHH E nanobody, genetically fused with the EsterLigase domain, was used as the specific probe for the spike receptor-binding domain (SP-RBD) protein as the target. The recognition between the two was measured by the change in the charge transfer resistance, determined by fitting the electrochemical impedance spectroscopy (EIS) spectra. The developed LSG-based biosensor achieved a linear detection range for the SP-RBD from 15 pM to 150 nM with a sensitivity of 0.0866 [log(M)]-1 and a limit of detection (LOD) of 7.68 pM.

Although hundreds of keV in energy gain have already been demonstrated in dielectric laser accelerators (DLAs), there remains challenge in creating structures that can confine electrons for multiple millimeters. We focus here on dual gratings with single sided drive, which have experimentally demonstrated energy modulation numerous times. Using a FTDT simulation to find the fields within various DLA structures and correlating these results with particle tracking simulation, we look at the impact of teeth height and width, as well as gap and offset, on the performance of these structures. We find a tradeoff between electron throughput and acceleration, but that for any given grating geometry there is a gap and offset that will allow some charge acceleration. For our 780 nm laser wavelength, this results in a 1200 nm optimal gap size for most gratings.

Dermal pigmentation is a challenging condition due to relative resistance to medical treatment and requirement of multiple sessions with modalities like chemical peels and lasers. There is inadequate literature regarding the efficacy and safety of lasers for dermal pigmentation in Indian skin. One hundred and twenty two patients were enrolled and divided into 4 groups: a) Dermal melasma b) Acquired dermal macular hyperpigmentation c) Nevus and d) Tattoo. Sequential combination of various lasers were used with different protocols for 4 different groups like ablative pixel Er:YAG, intense pulse light based technologies, Q-Switched and Alma Hybrid lasers for treatment of dermal pigmentation. A total of 4-10 sessions were conducted at three weekly intervals. Results were evaluated by comparing photographs at baseline, one month after the last session and then at 6 months interval to assess the relapse. All groups showed a statistically significant reduction in pigmentation. The mean treatment duration was 5-7 months for tattoo, lichen planus pigmentosus and melasma with 6-8 number of sessions. The mean treatment duration for nevus was 7-9 months with 8-10 sessions. Lasers are safe and effective modalities in Indian skin type for treatment of dermal pigmentation. Treatment period and relapse of dermal pigmentation may be reduced by combining resurfacing and chromophore selective lasers along with adequate dietary and lifestyle modifications to minimize complications and recurrence rates.

High-quality optical Fano resonances, which exist in a spherical dielectric microparticle in the spatial configurations of the "whispering-gallery modes" (WGMs) and recently are referred to as the “super-resonances”, possess extremal sensitivity not only to the micro-cavity size and shape but also to the optical properties of the particulate material. The increase in the power of light radiation coupling into a super-resonance can lead to the manifestation of strong optical nonlinearity of the resonator material due to the cubic nonlinearity (optical Kerr effect) and generation of free electron plasma in certain regions of the spherical microcavity. In fact, an optically linear medium of the resonance cavity transforms into a Drude-Kerr-type medium with a strong dependence on input laser intensity. With the help of the finite-elements numerical simulations, we theoretically analyze the transformations of the resonant contour for a number of high-quality WGMs excited in a lanthanum-glass microsphere exposed to an optical radiation of different intensity. We show that in a certain input intensity range, the competition of Kerr and plasma optical nonlinearities can stop and even reverse the Stokes shift of the super-resonance observed in a pure Kerr medium. Additionally, optical ionization and plasma generation within the mode volume significantly reduce the strength of the magnetic super-resonance and lead to its spoiling and frequency splitting.

Road marking recognition is of great importance for the deployment of automated driving systems and for already existing driver line-keeping assistance systems. For proper and reliable function of machine vision systems that include LiDAR and camera, road markings must be visible to them to facilitate planning of driving trajectory. In this study, LiDAR intensity and the number of LiDAR points collected from a field analysis of two road markings systems reflectorised with premium and standard glass beads were analysed. In the lateral direction, it was demonstrated that the use of premium glass beads for road markings lead to 56% higher LiDAR intensity and 14% more LiDAR points captured than in case of standard road markings. In the longitudinal direction, premium road markings showed less distance attenuation, which is seen as advantageous for trajectory planning by machine version systems. The outcomes of this study offer insights for road infrastructure decision-makers, developers of automated driving systems, and researchers in the field of transportation technology.

Laser heat treatment is applied after coating. Evaluation of the results was performed by studying the microstructures by metallographic, SEM/EDX microscopy and the mechanical properties were obtained by microscopic hardness and abrasion resistance. The objective of this study was to investigate the effect of laser heat treatment on the wear resistance of metal coatings. The results show the influence of the microstructure and chemical composition of the electrodes used on the micro-hardness and wear resistance of the metal coatings.

In this paper we present methodology for precise calibration of Molecular Beam Epitaxy (MBE) growth process and achieving run to run stability of growth parameters. We present the analysis of the influence of fluxes stability during the growth of long wavelength quantum cascade laser structures designed for the range λ ~ 12–16 µm on wavelength accuracy with respect to desired emission wavelength. The active region of the lasers has a complex structure of nanometer thickness InxGa1-xAs/InyAl1-yAs superlattice. As a consequence, the compositional and thickness control of the structure via bulk growth parameters is rather difficult. To deal with this problem we employ methodology based on double-superlattice test structures, that precede the growth of the actual structures. The test structures are analyzed by high-resolution X-ray diffraction which allows to calibrate the growth of the complex active region of quantum cascade laser structures. We also study theoretically the effect of individual flux changes on emission wavelength and gain parameters of the laser. The results of simulations allow for determination of flux stability tolerance, preserving acceptable parameters of the laser and provide means of emission wavelength control. The proposed methodology was verified by the growth of laser structures for emission at around 13.5 μm.

Matrix metalloproteinases (MMPs) are often considered biomarkers of skin fibrosis. At the early stages of the pathological process, an elevation of their enzymatic activity causes significant changes in the composition of the extracellular matrix. MMPs secreted by immune cells facilitate their migration to the site of damage. Then, the immune cells eliminate the affected cells and biomolecules. Moreover, bidirectional changes in the activity of proteolytic enzymes, including MMPs, accompany wound healing. This study aimed to assess changes in the expression of Mmp2, Mmp3, and Mmp9 after treating the mice with laser therapy using the experimental model of bleomycin-induced skin fibrosis. Using immunohistochemistry, we characterized the histological features of scarred skin. We also analyzed changes in the expression of MMPs using real-time polymerase chain reaction before and after the irradiation with laser. We showed that treatment of the mice with CO2 laser partially normalized the histological features of scarred skin. We also noticed a decrease in the expression of Mmp2, Mmp3 (both p < 0.05), and Mmp9 (p = 0.065) during scar healing. The obtained results suggest that normalization of skin homeostasis requires a control of MMPs activities via induction of their genes.

The temperature-assisted laser shock process has shown promising prospects in the fields of forming manufacturing and surface strengthening. However, large-scale application of this process is limited by the instability and failure of confinement medium at high temperatures (≥300 ℃). Aiming at this problem, we propose a novel laser shock strategy based on Leidenfrost effect, where the suspended droplets are utilized as the confinement medium. According to the sequence of images acquired by time delay system and high-speed camera, the droplet dynamics behavior is studied. The focusing enhancement effect of the droplet is comprehensively explored. And the correlations between droplet size, ambient temperature, vapor layer thickness and focusing effect are investigated. Combining the dynamics and focusing enhancement effect of droplets, a theoretical model of laser shock pressure under droplet confinement is established. Finally, the effectiveness and feasibility of the droplet-based laser shock strategy in high temperature processing environments are verified by typical applications in laser shock forming and laser shock peening fields. The results show that the droplet-based laser shock process presents better forming effect. And the mechanical property tests demonstrate that this process can obtain the simultaneous improvement of the strength (~51%) and ductility (~6.4%) of annealed Cu. The multiscale plasticity mechanisms of the strengthened material are comprehensively investigated. We believe that this low-energy, low-cost and high-quality process can provide a new solution for the industrial application of laser shock at high temperatures.

Nanoscale structuring/printing is of interest for range of applications in 3D subtractive and additive manufacturing (3D^+/-). Basic principles of light field enhancement and control at the nanoscale are overviewed in this section/chapter for bulk, surface, and localised plasmons (1D, 2D, and 3D localisation, respectively). All these plasmons are resonant phenomena which have common Lorentzian spectral lineshape which relates refractive and absorption properties as well as defining the phase of transmitted and scattered light. Localisation of light at the nanoscale creates the possibility of modification with matching resolution. Harnessing this light enhancement can be demonstrated as a "nano-pen" for direct write nanolithography.

Numerical calculations of ultraviolet to near-infrared absorption spectra by cadmium selenide quantum dots (CdSe QDs) doped in anodic aluminum oxide pores were performed using a finite-difference time-domain model. The height, diameter, and periodic spacing of the pores were optimized. Light absorption by the dots was enhanced by increasing the height and decreasing the diameter of the pores. When the height was less than 1 μm, visible light absorption was enhanced as the spacing was reduced from 400 nm to 100 nm. No enhancement was observed for heights greater than 6 μm. Finally, the optical mode coupling of the aluminum oxide and the quantum dots was enhanced by decreasing the pore diameter and periodic spacing, and increasing the height. Laser ablation verified light absorption enhancement by the CdSe QDs. The experiment verified the improvement of the laser-induced damage ability with wavelength of 355-nm after aluminum alloy 6061 coated with functional films, which was fabricated based on numerical calculations.

Pollen analysis as a part of palynology deals with the morphological determination of pollen and spores. Different technologies with different resolutions varying from simple light microscopy to highly elaborate electron microscopy are used for the examination, depending on the area of application (e.g. sedimentology, melissopalynology, forensic palynology, etc.). To answer the question of whether laser scanning microscopy (LSM) can replace scanning electron microscopy (SEM) for the determination of pollen species, 168 species were examined using LSM. It was concluded that LSM is both efficient and easy to handle. After preparing the fresh pollen, a 3D laser scan takes 5-10 minutes and unlike using SEM, the pollen does not have to be sputtered or processed. The 3D scans can be measured quickly and easily with the integrated software and there were no observable artifacts. At magnifications up to 8545x, the image quality is comparable to that of a sputtered SEM sample whereas at higher magnifications, the SEM method is superior. Overall, pollen display by LSM is much less time consuming and more cost effective than with the SEM method.

Pain is an unpleasant emotional and sensory experience. For many years orthodontists have been looking for an effective method of reducing this feeling of discomfort. In recent years, low-level laser therapy (LLLT) has taken hold in the orthodontic field. Among the countless advantages it can modulate the painful feeling. The aim of this research is to identify the use of photobiomodulation in subjects undergoing fixed orthodontic treatment, to reduce the pain and discomfort that it causes. The research was conducted from the Web of Science, Pubmed and Scopus databases. Only 14 of all articles met the inclusion and exclusion criteria and were therefore used to conduct the research. The different studies compared, in most cases, patients whose mouth was divided into a part treated with laser therapy and a placebo part. The results show a statistically significant difference in perceived pain between the irradiated arch and the non-irradiated arch. Three authors didn’t find statistically significant results in favour of low-laser therapy, but it is important to remember that they used different parameters. To obtain generally valid studies, with consistent and reproducible results, it is necessary to standardize the different parameters used that are independent by operator performing the procedure.

Spatial light modulators (SLMs) have been widely used to achieve dynamic control of optical traps. Often, holographic optical tweezers have been presumed to provide nanometer or sub-nanometer positioning accuracy. It is known that some features concerning the digitalized structure of SLMs cause a loss in steering efficiency of the optical trap, but their effect on trap positioning accuracy has been scarcely analyzed. On the one hand, the SLM look-up-table, which we found to depend on laser power, produces positioning deviations when the trap is moved at the micron scale. On the other hand, phase quantization, which makes linear phase gratings become phase staircase profiles, leads to unexpected local errors in the steering angle. We have tracked optically-trapped microspheres with sub-nanometer accuracy to study the effects on trap positioning, which can be as high as 2 nm in certain cases. We have also implemented a correction strategy that enabled the reduction of errors down to 0.3 nm.

One of the challenges facing the industrial adoption of additively manufactured parts is the surface roughness on the as-built part. The surface roughness of parts is frequently characterized by metrics specified by international standards organizations. However, these standards list many surface metrics that can make it unclear which to use to best describe the surface. In this work, the ability of the various surface metrics to successfully classify the as-built and post-processed surfaces is studied using linear classification models. Laser polishing via remelting and manual grinding are the post-processing techniques used to smooth the as-built surface. The ability of the linear classifier to successfully categorize the various surfaces is demonstrated, and the various surface metrics are ranked according to the strength of their individual ability to classify the surfaces. This work promotes the method as a potential way to autonomously classify as-built and laser polished surfaces.

The study examined the effect of noninvasive crown retrieval/reuse process using erbium-doped yttrium aluminum garnet laser (Er:YAG). Twenty-six extracted human teeth were prepared for a crown. The crown was milled using lithium disilicate (LD) and zirconia (Z) materials, n=13 per group, 3 for scanning electron microscopy (SEM). The crown was luted using composite resin cement and subjected to a laser retrieval process. After the retrieval process, the crown was cleaned, recemented and laser-retrieved two more times, without and with additional tooth reduction mimicking clinical refreshment of dentin. Retrieval time and temperature were analyzed using analysis of variance (ANOVA). Surface changes were observed through SEM. The retrieval times were 267.1±130.43, 220±79.09, 277.1±126.44, 368.4±136.14, 355±159.39, and 419.2±121.36 seconds for first, second, third LD and Z groups, respectively (p=.009). The maximal temperatures were 23.95.1±1.89°C, 24.86±2.01°C, 24.17±1.53°C, 22.88±1.51°C, 24.03±1.74°C, and 21.99±1.32°C for for first, second, third LD and Z groups, respectively (p=.006). Er:YAG laser crown removal is an effective retrieval tool for all-ceramic crowns. Minimal changes to teeth and crowns were observed following laser irradiation.

The interest in dry EEG electrodes has increased in recent years and especially as everyday suitability earplugs for measuring drowsiness or focus of auditory attention. However, the challenge is still the need for a good electrode material, which is reliable and can be easily processed for highly personalized applications. Laser processing as used here is a fast and very precise method to produce personalized electrode configurations that meet the high requirements of in-ear EEG electrodes, for example. The arrangement of the electrodes on the very flexible and compressible mats allows an exact alignment of the electrodes to the ear mold and contributes to a high wearing comfort, as no edges or metal protrusions are present. For better transmission properties, an adapted coating process for surface enlargement of platinum electrodes is used, which allows easy control of the thickness and growth form of the porous layer. The porous platinum-copper alloy is chemically very stable, shows no exposed copper residues and enlarges the effective surface area by 40. In a proof-of-principle experiment, these porous platinum electrodes could be used to measure the Berger effect in a dry state using just one ear of a test person. Their signal-to-noise ration and frequency transfer function is comparable to gel-based silver/silver chloride electrodes.

Laser scanning is an effective tool for acquiring geometric attributes of trees and vegetation, which lays a solid foundation for 3-dimensional tree modelling. Existing studies on tree modelling from laser scanning data are vast. Nevertheless, some works don’t ensure sufficient modelling accuracy, while some other works are mainly rule-based and therefore highly depend on user inputs. In this paper, we propose a novel method to accurately and automatically reconstruct tree branches from laser scans. We first extract an initial tree skeleton from the input tree point cloud, then simplify the skeleton through iteratively removing redundant components. A global-optimization approach is performed to fit a sequence of cylinders to approximate the geometry of the tree branches. Experiments on various types of trees from different data sources demonstrate the effectiveness and robustness of our method. The resulted tree models can be further applied in the precise estimation of tree attributes, urban landscape visualization, etc.

Inorganic and organic – inorganic (hybrid) perovskite semiconductor materials have attracted the worldwide scientific attention and research effort as the new wonder material in optoelectronics. Their excellent physical and electronic properties have been exploited to boost the solar cells efficiency beyond 23% and captivate their potential as competitors to the dominant silicon solar cells technology. However, the fundamental principles in Physics dictate that an excellent material for photovoltaic applications must be also an excellent light emitter. This has been realized for the case of perovskite based light emitting diodes (LEDs) but much less for the case of the respective laser devices. Here, the strides have been made since 2014 are presented for the first time. The solution processability, low temperature crystallization, formation of nearly defect free, nanostructures, the long range ambipolar transport, the direct energy band gap, the high spectral emission tunability over the entire visible spectrum and the almost 100% external luminescence efficiency show perovskite semiconductors’ potential to transform the nanophotonics sector. The operational principles, the various adopted material and laser configurations along the future challenges are reviewed and presented in this paper.

Being able to forecast events is of great importance in many fields, from brain behavior to earthquakes or stock markets. Because each dynamical system has intrinsic features, different statistical tools have to be used for each system. Here we study the time series of the output intensity of a fiber laser with an ordinal patterns analysis, and we look for temporal correlations in order to statistically forecast the most intense events. We set two thresholds, a low one and a high one, to distinguish between low intensity versus high intensity events. We find that when the time series is performing events below the low threshold it shows some preferred temporal patterns before performing events above a high threshold.

For development and successful application of any material, a clear understanding of their mechanical behavior is one of the most important things, but when it comes to nanofibers networks it become a challenge due to, their high porosity, many scales in their structure, and characteristics non-linear. Therefore, an experimental methodology in conjunction with a theoretical model that can fully consider their characteristics is still needed. In this work we proposed a model that incorporates the propagation of the elastic waves in two-phase media to determine the effective elastic modulus of electrospun membranes of PLA/gelatin given the mechanical properties of nanofibers, shape, distribution and concentration. The model was verified via laser ultrasonic testing. It was found that the values predicted for the effective modulus by the model were higher than the values obtained from experimental results. One explanation is due to the experimental density. As a result, the P-Wave velocity from the model best fit to experimental results and it has the same behavior, decrees as the concentration of gelatin in the solution. These results indicate the model and experimental methodology can assist in the dressing of nanofibers networks and electrospun materials.

The purpose of this study consists to verify if Er:YAG laser, at low fluences, is able to debond porcelain veneers, successfully used to improve anterior tooth esthetics, without damaging the tooth structures. A total of twelve freshly extracted teeth were used and samples were decontaminated, stored, prepared to obtain Veneers adhesion. One week after, Er:YAG laser with a non-contact sapphire tip with air-water spray was used for veneer debonding at 100 mJ of power and 30Hz of frequency (Fluence 5.91 J/cm2). Results demonstrated that veneer debonding is possible with an Er:YAG laser and that the total number of pulses does not seem related to its efficiency. SEM observation confirms that residual tooth structure is not altered when using these low fluences. Low fluences with Er:YAG laser are able to debond veneers while preserving the tooth structures. SEM observation confirmed that residual tooth structure is not altered with low fluences.

The development of organ-on-chip and biological scaffolds is currently requiring simpler methods to microstructure biocompatible materials in three dimensions, fabricate structural and functional elements in biomaterials or modify the physicochemical properties of desired substrates. Aiming at addressing this need, a low-power CD-DVD-Blu-ray laser pickup head was mounted on a programmable three-axis micro-displacement system in order to modify the surface of polymeric materials in a local fashion. Thanks to a specially-designed method using a strongly absorbing additive coating the materials of interest, it has been possible to establish and precisely control processes useful in microtechnology for biomedical applications. The system was upgraded with blu-ray laser for additive manufacturing and ablation on a single platform. In this work, we present the application of these fabrication techniques to the development of biomimetic cellular culture platforms thanks to the simple integration of several features typically achieved with traditional, less cost-effective microtechnology methods in one step or through replica-molding. Our straightforward approach indeed enables great control of local laser microablation or polymerization for true on-demand biomimetic micropatterned designs in transparent polymers and hydrogels and is allowing integration of microfluidics, microelectronics, surface microstructuring and transfer of superficial protein micropatterns on a variety of biocompatible materials.

Auricular keloids pose significant aesthetic and functional challenges, and traditional treatments often fall short in ad-dressing these. Our study presents an innovative combined approach of ablative CO2 and dye laser therapy for improved keloid management. This treatment protocol was applied to 15 patients with auricular keloids after an initial multispec-tral analysis to assess keloid composition. The laser sequence was tailored per patient based on this analysis. Evalua-tions using the Vancouver Scar Scale and Patient and Observer Scar Assessment Scale were carried out at baseline and at 3-week intervals post-treatment. The results showed a significant reduction in these scores at the final follow-up (p<0.05), suggesting improvements in keloid color, texture, and pliability, with minimal adverse events. Additionally, no recur-rence of keloids was observed. Our findings indicate that this novel methodology of multispectral analysis followed by tailored laser therapy may offer a safe and effective solution for auricular keloids, promising enhanced keloid treatment and prevention of recurrence. However, further investigations, including randomized controlled trials, are needed to confirm and optimize this treatment protocol.

This work communicates analysis of aluminum monoxide, AlO, laser-plasma emission records using line strength data and the ExoMol astrophysical database. A nonlinear fitting program computes comparisons of measured and simulated diatomic molecular spectra. Predicted cyanide spectra of the AlO, ${\rm B}\ ^2\,\Sigma^+ \longrightarrow {\rm X} \ ^2\,\Sigma^+$, $\Delta {\rm v} = 0, \pm 1, \pm 2, + 3$ sequences and progressions compare nicely with 1 nanometer resolution experimental results. The analysis discusses experiment data captured during laser ablation of Al$_2$O$_3$ with 266-nm, 6-mJ pulses. The accuracy of the AlO line strength data is better than one picometer. This work presents as well comparison of the $^{27}$Al$^{16}$O line strength and of ExoMol data for spectral resolutions of 0.1nm and 0.07nm. Accurate AlO databases show a volley of applications in laboratory and astrophysical plasma diagnosis.

This work communicates laser-plasma experiments in a gaseous mixture of hydrogen and nitrogen. Time-resolved spectroscopy measures the first four Balmer series hydrogen lines together with selected neutral and ionized nitrogen lines. Optical breakdown plasma is generated in a 1:1 hydrogen:nitrogen mixture at ambient temperature and 0.27-atm pressure. Time-resolved spectroscopy records emitted radiation with spatial resolution along the slit height for the H_α, H_β, H_γ, and H_δ lines. For 13 selected time delays from 0.25 µs to 3.25 µs and 0.025 µ gate-widths, micro-plasma diagnostics is evaluated. Of interest are the peak-separation and width of H_δ and width of H_γ for electron densities in the range of 0.1 to 1.0×10¹⁷ cm^-3, and comparisons with H_β and H_α diagnostics. Integral inversions interrogate spatial distributions of the plasma expansion. Applications include laboratory and stellar astrophysics plasma diagnosis.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

Vit-106 is a promising zirconium-based alloy with high glass-forming ability and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions can be obtained from a BMG alloy by casting. However, further increasing the cast size decreases the cooling rate and thus induces crystallization. Selective laser melting (SLM) is a well-known technique to overcome the size limitations for BMGs because a workpiece is built by the addition of multiple melt portions where the cooling rate is kept above the critical one. Currently, BMG parts obtained by SLM suffer from partial crystallization. The present work studies the influence of SLM process parameters on partial crystallization of Vit-106 by metallography and the influence of the microstructure on mechanical properties by microhardness and wear resistance testing. Submicron crystalline inclusions are observed in an amorphous matrix of Vit-106 alloy obtained by SLM. The size and the concentration of the inclusions can be controlled by varying the laser scanning speed. It is shown that submicron crystalline inclusions formed in the amorphous matrix during SLM can favorably affect microhardness and wear resistance.

Nerve agents have recently been used in battlefield operations, espionage wars and terrorist attacks. These compounds, like some pesticides, cause organophosphate poisoning. The rapid, non-contact detection of a sarin simulant has been demonstrated at the Diagnostics and Metrology Laboratory of the Italian National Agency for New Technologies, Energy and Sustainable Economic Development using laser photoacoustic spectroscopy, an infrared absorption technology. The first measurements, carried out with an experimental system based on a quantum cascade laser and developed for the assessment of food authenticity in the “fingerprint region”, show that a detection limit of 1 nanolitre is within the reach of the instrument when chemometric analysis is applied.

This article presents analysis of carbon Swan, C$_2$, laser-plasma emission records using line strength data, C$_2$-Swan-lsf, and the ExoMol astrophysical database. Line-strength data fitting of 0.25-nanometer spectral resolution ExoMol-computed spectra for a 6,000-Kelvin temperature C$_2$ Swan system, ${\rm d}\ ^3\,\Pi_{\rm g} \longrightarrow {\rm a} \ ^3\,\Pi_{\rm u}$, $\Delta {\rm v} = 0, \pm 1$, reveals a temperature of 5,640 Kelvin. The six per cent lower temperature is associated primarily with the accuracy of the transition wavelengths in the ExoMol vs. C$_2$-Swan-lsf data. The analysis of experiment data examines spectra that are recorded following laser-induced optical breakdown in carbon monoxide. The laser plasma data are recorded with 0.35-nm spectral resolution. The temperature inferences are elaborated when using non-linear fitting with both databases. The results show temperatures in excess of 6,000 Kelvin for the $\Delta {\rm v} = -1$ sequence, and for a time delay of 30\,$\upmu$s from laser plasma initiation. The accuracy of the C$_2$ Swan bands line strength data is of the order of 1 picometer. These line strength data are also utilized for analysis of laser-induced fluorescence experiments that employ a spectral resolution of 5.5 picometer, and a temperature of 2,716 Kelvin is inferred. Accurate C$_2$ databases show many applications in laboratory diagnosis and interpretation of astrophysical plasma records.

Laser Direct Writing (LDW), also known as 3D multi-photon laser lithography of resins, is a promising technique for fabricating complex free-form elements, including micro-optical functional components. Regular organic or hybrid (organic-inorganic) resins are often used, with latter exhibiting better optical characteristics, as well as having the option to be heat-treated into inorganic glass-like structures, particularly useful for resilient micro-optics. While this work is a continuation of SZ2080™ calcination development , the Laser-Induced Damage Threshold (LIDT) of such sol-gel-derived glass micro-structures, particularly those that undergo heat treatment, has not been well-characterized. In this pilot study, we investigated the LIDT using the Series-on-One (S-on-1) protocol of functional micro-lenses produced via LDW and subsequently calcinated. Our results demonstrate that the LIDT can be significantly increased, even multiple times, by this approach, thus enhancing the resilience and usefulness of these free-form micro-optics. This work represents the first investigation in terms of LIDT into the impact of calcination on LDW produced sol-gel-derived glass micro-structures, and provides important insights for the development of robust micro-optical devices.

The first detection of gypsum (CaSO4.2H2O) by the Mars Science Laboratory (MSL) rover Curiosity in the Gale Crater, Mars created a profound impact on planetary science and exploration. The unique capability of plasma spectroscopy involving in situ elemental analysis in extraterrestrial environments, suggesting the presence of water in the red planet based on phase characterization and providing a clue to Martian paleoclimate. The key to gypsum as an ideal paleoclimate proxy lies in its textural variants, and in this study terrestrial gypsum samples from varied locations and textural types have been analyzed by Laser Induced Breakdown Spectroscopy (LIBS) technique. Petrographic, sub-microscopic and powder X-ray diffraction characterizations confirm the presence of gypsum (hydrated calcium sulphate; CaSO4.2H2O), bassanite (semi-hydrated calcium sulphate; CaSO4.1/2H2O) and anhydrite (anhydrous calcium sulphate; CaSO4) along with accessory phases (quartz and jarosite). The principal component analysis of LIBS spectra from texturally varied gypsums can be differentiated from one another because of the chemical variability in their elemental concentrations. The concentration of gypsum is determined from the partial least-square regressions model. Rapid characterization of gypsum samples with LIBS is expected to work well in extraterrestrial environments.

The pervasive use of screens, averaging nearly 7 hours per day globally across mobile phones, computers, notebooks and TVs, has sparked a growing desire to minimize reflections from ambient lighting and enhance readability in harsh lighting conditions, without the need to increase screen brightness. This demand highlights a significant need for advanced anti-glare (AG) technologies, to increase comfort and eventually reduce energy consumption of the devices. Currently used production technologies are limited in their texture designs, which can lead to suboptimal performance of the anti-glare texture. To overcome this design limitation and improve performance of the anti-glare feature, this work reports a new, cost-effective high-volume production method that enables the much needed design freedom on a large area. This is achieved by combining mastering via large-area Laser Beam Lithography (LBL) and replication by Nanoimprint Lithography (NIL) processes. The environmental impact of the production method, such as material consumption, are considered and the full cycle from design to final imprint is discussed.

The present study investigates the impact of electrode surface roughness on the electrofreezing of water. This research focuses on how the electrode roughness induced by a laser treatment affects the nucleation and growth of ice crystals under controlled electric fields. To achieve this, a series of experiments were conducted using deionized water samples placed between electrodes with varying surface roughness. The electrodes, fabricated with the Al6061 T6 alloy were structured via the Laser Shock Processing (LSP) method. For this purpose, the pulsed densities during the LSP process were varied from 900 to 2500 pulses/cm2. The increase of the pulse density was correlated to the surface structuring and to the microstructural features and average roughness of the LSP-treated Al6061 alloy. A wavy-like microstructure was induced upon the LSP treatment with average roughnesses between ~ 3.5 and 6 µm at the selected pulse densities. The results indicate that electrode roughness significantly influences the electrofreezing process. Rougher electrodes were found to lower the nucleation temperature compared to smoother ones, suggesting enhanced ice nucleation activity. The findings are attributed to the increased electric field concentration at the asperities of the rough surfaces, which may facilitate the alignment of water molecules and the formation of critical ice nuclei.

High levels of heavy metal contamination in soil present substantial threats to human health and the environment, leading to severe health problems such as neurotoxicity, cancer, kidney issues, chronic obstructive pulmonary disease, and reduced life expectancy. This research aims to identify and analyze heavy metals in soil samples collected from Superfund sites in North Birmingham, Alabama, specifically in affected areas with Zip codes 35207, 35217, and control area 35214. These affected areas were previously used for mining, coal-fired power plants, coke furnaces, smelting, and other potential sources of heavy metal pollution. Laser-Induced Breakdown Spectroscopy (LIBS) was employed to study 60 soil samples systematically collected from affected and control areas. We found that using LIBS, we could detect arsenic (As), lead (Pb), and manganese (Mn) in all soil samples from the affected areas. The limit of detection (LoD) was 16 ppm for Pb, 43 ppm for As, and 33 ppm for Mn using specific parameters of the detection system and/or argon gas purging at atmospheric pressure. The results were compared with ICP-MS measurements to validate the accuracy of the LIBS findings. Data showed a good linearity for all calibration data at relatively low concentrations and a good correlation between ICP-MS measurements.

Plantar fasciitis is one of the most common causes of foot pain; in a significant percentage it is also associated with bone edema of the heel. A prospective randomized clinical trial was designed, in which 48 patients suffering from plantar fasciitis, with or without bone edema, were treated with temperature controlled high energy adjustable multi-mode emission laser and exercises (laser group) or with exercises only (control group). Patients were evaluated at recruitment (T0), at 2 (T1) and 6 months (T2), monitoring pain (with Visual Analogue Scale), functionality (with Foot Function Index) and perception of improvement (with Roles and Maudsley Score) and fascia thickness (with ultrasound examination). In both groups there was a significant improvement in pain, functional recovery, perception of remission and a reduction in plantar fascia thickness at T1 and T2. The laser group presented statistically better values at T2 for the Roles and Maudsley Score (z: 2.21; 0.027). Regression analysis showed that a greater reduction in fascia thickness occurred in the laser group (p-value: 0.047). In conclusion, the two conservative treatments were effective in patients suffering from plantar fasciitis, even in the presence of bone edema, but with lesser results.

The phenomena of light absorption, fluorescence and laser emission are accounted for within a unique picture. The atomic dipole is dealt with in a quantum framework, whereas the electromagnetic field is assumed to be a classical sine-wave. The on and off resonance cases are investigated. This is achieved owing to a novel application of Poynting's theorem. Observable predictions are made, regarding absorption of the electromagnetic energy and the frequency bandwidth of light emitted either by fluorescence or laser effect.

Oral candidiasis is a common problem among immunocompetent patients. The frequent resistance of Candida strains to popular antimycotics makes it necessary to look for alternative methods of treatment. The authors conducted a systematic review following the PRISMA 2020 guidelines. The objective of this review was to determine whether curcumin-mediated aPDT and blue light could be considered as an alternative treatment for oral candidiasis. PubMed, Google Scholar and Cochrane Library databases were searched using a combination of the following keywords: (Candida OR candidiasis oral OR candidosis oral OR denture stomatitis) AND (curcumin OR photodynamic therapy OR aPDT OR photodynamic antimicrobial chemotherapy OR PACT OR photodynamic inactivation OR PDI). The review included in vitro laboratory studies with Candida spp., in vivo animal studies, and randomized control trials (RCTs) involving patients with oral candidiasis or prosthetic stomatitis, published only in English. The method of elimination of Candida species in the studies was curcumin-mediated aPDT. 757 studies were identified. Following the analysis of the titles and abstracts of the studies, only 42 studies were selected for in-depth screening, after which 26 were included in this study. All studies evaluated the antifungal efficacy of curcumin-mediated aPDT against C. albicans and non-albicans Candida. In studies conducted with planktonic cells solutions, seven studies demonstrated complete elimination of Candida spp. cells. The remaining studies demonstrated only partial elimination. In all cases, experiments on single-species yeast biofilms demonstrated partial, statistically significant inhibition of cell growth and reduction of biofilm mass. In vivo, curcumin-mediated aPDT has shown good antifungal activity against oral candidiasis also in an animal model. However, its clinical efficacy as a potent therapeutic strategy for oral candidiasis requires further RCTs.

Laser-plasma interactions of ultra-short laser pulses with solid targets can generate highly intense pulses of protons and ions with energies of several MeV. The spectra of these particles are spread over a wide range following a Maxwellian distribution. We report on the design and testing of a magnetic chicane for the selection of protons within a limited energy window. It consists in two successive, anti-parallel dipole fields generated by cost-effective, permanent C-magnets with customized configuration and longitudinal positions. The chicane has been implemented into the target vessel of a petawatt laser facility under constraints on the direction of the incoming laser beam and guidance of the outgoing particles through a vacuum port. The separation of protons and carbon ions within distinct energy intervals has been demonstrated and compared to a ray tracing code.

Purpose: To examine the effectiveness of patterned laser trabeculoplasty (PSLT) as an additional treatment for patients of open-angle glaucoma (OAG) receiving maximized ocular hypotensive medications (OHM). Methods: Forty eyes of 33 patients (average age 72.7±10.7 years) who had not previously undergone open glaucoma surgery or laser trabeculoplasty and were treated with maximized OHM between June 2018 and March 2022 were included. A 360-degree PSLT was conducted and postoperative intraocular pressure (IOP) and survival curves at 1, 3, 6, 9, and 12 months were evaluated. Results: According to the Kaplan-Meier survival analysis, the average survival time was 8.1 months with death defined as postoperative IOP reduction of less than 10% or requiring additional treatment. The average survival time was 4.9 months with death defined as postoperative IOP reduction of less than 20% or requiring additional treatment. In the 31 eyes which received no additional treatment after PSLT, the mean preoperative IOP was 18.5±3.9 mmHg, which reduced to 15.3±4.1 mmHg (p=1.62 x 10-6)), 15.5±3.4 mmHg (p=1.51 x 10-5), 15.7±4.0 mmHg (p=1.75 x 10-5), 14.7±4.38 (p=2.89 x 10-6), and 15.0±4.0 mmHg (p=5.74 x 10-9) at 1, 3, 6, 9 and 12 months after PSLT, respectively. The IOP reduction rate one year after PSLT was 18.7%. Thirteen of the 31 eyes (42%) achieved a 20% reduction in IOP compared to the baseline. Conclusion: Adjunctive treatment with PSLT in OAG patients receiving maximized OHM may be effective over 12-months of follow-up.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Agriculture and rural regions in Europe face a number of economic, social and environmental challenges. Rural areas are active players in the EU’s green transitions. Weeding is one of the most important factors of agricultural production. New weeding techniques are being developed to enhance sustainability. Among them laser based weeding seems a promising alternative for use of chemicals. WeLASER technique is a novel technique of weed control. Its successful implementation depends on many factors related to the innovation itself, policy context, farming conditions and users’ attitudes. Survey was carried out to provide the insight on the attitudes toward the innova-tive (laser) weed control tool (device - autonomous robot). The CATI method was selected for the survey of farmers opinion and carried out in three countries: Denmark, Spain and Poland. Statistical methods were applied to analyze the results. The study provided knowledge on how farmers see the barriers and opportunities of implementing the device in practice. Positive attitudes of farmers were observed but with high expectations related to quality of the technique and systemic conditions of its implementation.

This paper describes design of experimental methodology developed to measure the working properties of accuracy of the path traversed by a collaborative robot. The methodology proposed here uses a collaborative robot and a laser measuring system Gepard from Raytec. The main parts of the measuring chain and the ISO 9283 standard are described. The proposed experimental methodology should examine working properties of industrial robots, such as the properties of position and path. The focus of this paper lies on the path accuracy of robots. Currently, the interest in this topic is on the rise and the measuring systems capable of recording this parameter are too costly. This paper focuses on experimental measuring of the path properties, describing them in more detail. The measuring and results were processed in the software tool developed for Gepard.

In mobile robotics, laser scanners have a wide spectrum of indoor and outdoor applications, both in structured and unstructured environments, due its accuracy and precision. Most works that use this sensor have their own data representation and their own case-specific modeling strategies, and no common formalism is adopted. To address this issue, this manuscript presents an analytical approach for identification and localization of objects using a 2D LiDARs Our main contribution lies in formally defining laser sensor measurements and their representation, the identification of objects, their main properties and their location in a scene. We validate our proposal with experiments in generic semi-structured environments common in autonomous navigation, and we demonstrate its feasibility on multiple object detection and identification, following strictly its analytical representation. Finally, our proposal further encourages and facilitates the design, modeling and implementation of other applications that use laser scanners as a distance sensor.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

Axions can be stimulated to decay to photons by ambient photons of the right frequency or by photons from decay of neighboring axions. If the axion density is high enough the photon intensity can be amplified, which is a type of lasing or an axion maser. Here we review the astrophysical situations where axion lasing can appear and possibly be detected.

The laser sintering process and modification of electrophoretic deposition (EPD) YSZ coatings on YSZ air plasma sprayed thermal barrier coatings (TBCs) were investigated. Ni-based superalloy was plasma sprayed using yttria-stabilized zirconia (YSZ) to perform thermal barrier coating with 400 μm thickness. The electrophoretic deposition (EPD) technique was used for depositing nanopowder of YSZ on the surface of YSZ TBCs. In this study, a technology of direct sintering the green EPD layer by laser beam was carried out. The best conditions of deposition YSZ overlay coating using DC current were obtained with applied voltage 40 V, deposition time 5 min, and suspension concentration 10 g/l. Iodine was added to the solutions as the stabilizing agent. To overcome the disadvantages of high sintering temperatures, laser sintering was taken as a new approach. Microstructures for all specimens were studied using Field Emission Scanning Electron Microscopy (FESEM) with EDS analysis. Surface roughness was investigated using AFM analysis and central line average (CLA). The results indicated that the morphology after the direct laser sintering of the EPD layer has a fine and controllable grain size, high hardness, and low roughness. Which is better than the direct laser on plasma-sprayed coatings.

Fused silica glass is a material with outstanding mechanical, thermal and optical properties. Being a brittle material, it is challenging to shape. In the last decade, the manufacturing of monolithic flexible mechanisms in fused silica has evolved with the femtosecond laser-assisted etching process. However, instrumenting those structures is demanding. To address this obstacle, this article proposes to inscribe a Bragg Grating sensor inside a flexure and interface it with an optical fibre to record the strain using a spectrum analyzer. The strain sensitivity of this Bragg Grating sensor is characterized at 1.2 pm/μϵ (1 μϵ = 1 microstrain). Among other applications, deformation sensing can be used to record a force. Its use as a micro-force sensor is estimated. The sensor resolution is limited by our recording equipment to 30 μN over a measurement range above 10 mN. This technology can offer opportunities for surgery applications or others where precision and stability in harsh environments are required.

The impact induced by cavitation bubble collapse can be utilized for mechanical surface treatment to improve fatigue properties of metals including additive manufactured metallic materials. A peening method using cavitation impact induced by a pulsed laser is called “laser cavitation peening (LCP)”. Normally, a Q-switched Nd:YAG laser, whose pulse width is a few nanoseconds, is used for LCP, which improves the fatigue strength. The problem with LCP is that the processing time is too slow. If a laser pulse whose pulse width is a few hundred microseconds can be utilized for LCP, the repetition frequency can be increased drastically using other types of laser systems such as a fiber laser. In the present paper, in order to reveal the possibility of LCP using a pulsed laser width of a few hundred microseconds, the use of LCP with a normal-oscillation Nd:YAG laser (pulse width ≈ 200 us) was investigated. It is demonstrated that LCP with the normal-oscillation Nd:YAG laser produced curvature in an aluminum alloy plate.

Selective laser sintering (SLS) has drawn attention for the fabrication of three-dimensional oral dosage forms due to the plurality of drug formulations that can be processed. The aim of this work was to employ SLS with a CO2 laser for the manufacturing of carvedilol personalised dos-age forms of various strengths. Carvedilol (CVD) and vinylpyrrolidone-vinyl acetate copolymer (Kollidon VA64) blends of various ratios were sintered to produce CVD tablets of 3.125, 6.25 and 12.5 mg. The tuning of the SLS processing parameter laser intensity, improved printability and impacted the tablet hardness, friability, CVD dissolution rate, and the total amount of drug re-leased. Physicochemical characterization showed the presence of CVD in the amorphous state. X-ray micro-CT analysis demonstrated that the applied CO2 intensity affected the total tablet po-rosity, which was reduced with increased laser intensity. The study demonstrated that SLS is a suitable technology for the development of personalised medicines that meet the required specifications and patient needs.

The dynamics of the topological charge of a vortex optical beam propagating in a turbulent air with accounting for the cubic nonlinearity is theoretically considered. On a number of examples, we show that the optical beam self-focusing manifests itself ambiguously depending on optical wave power. At near-critical values of beam power, self-focusing leads to enhanced spatial localization of optical vortices and substantial suppression of vortex walk-off relative to the beam axis caused by air turbulence. However, with increasing of optical intensity the modulation instability imposed by cubic nonlinearity becomes significant and contributes jointly with medium turbulence to faster divergence of vortex beams.

Crystallization often occurs in the laser welding of amorphous alloys, reducing the amorphous alloys’ properties. So, it is necessary to simulate the temperature field curve of the welding area by computer and then determine the power and laser moving speed of laser welding. In this paper, the temperature field curve of Zr41.2Ti13.8Cu12.5Ni10Be22.5(Vit1) amorphous alloy in laser welding is obtained by finite element analysis. The continuous heating curve (CHT) of Vit1 is fitted by the Vogel-Fulcher-Tammann (VFT) equation and the Kissinger equation. If the temperature field curve intersects with the CHT curve, crystallization occurs. The experiment results show that the VFT equation can be used to predict the crystallization of Vit1 better in laser welding. The tem-perature and welding time are increased by using low welding speed. Therefore, the temperature of the weld zone cannot fall in time, resulting intersection of the temperature field curve and the CHT curve. So, crystallization can be avoided if the welding speed is controlled within a rea-sonable range, and the highest temperature is kept under the CHT curve.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

Adaption of laser communication terminals to airborne and lean-satellite platforms is now a vogue, made possible due to the progressing advancements in lightweight components and compactness of onboard electro-optical transceivers and control systems. This enables highly secured and superior data-transmission rates beyond multiple Gigabit/second on CubeSats and drones compared to Megabit/second rates offered by similar radio-transceivers form factors. However, laser-transmission links require a very stringent beam-pointing stability because they are easily perturbed by attitude variations and micro-vibrations generated by the host platform’s propulsion system or other mechanically active subsystems in proximity with the transmitter’s optical head. Severe line-of-sight jitter causes the downlink laser beam to drift from the targeted receiving system’s field-of-view, inducing pointing errors, increasing signal outage probability and information loss. We experimentally examine the platform jitter generated by the propellers of an hexacopter drone during ground operation and the attitude-control unit’s reaction wheels in a 6U CubeSat structure. We determined the vibration spectrum unique to these platforms and accordingly prescribe requirements for applicable optical fine pointing and disturbance isolation or suppression systems needed to achieve a high-fidelity laser-communication link.