To compare the quality of low-energy VMIs obtained with three DECT platforms according to phantom diameter. Three sections of the Mercury Phantom 4.0 were scanned on two generations of split-filter CTs (SFCT-1st and SFCT-2nd) and on one Dual-source CT (DSCT). Noise power spectrum (NPS), task-based transfer function (TTF) and detectability index (d’) were assessed on VMIs from 40 to 70keV. Highest noise magnitude values were found with SFCT-1st and noise magnitude was higher with DSCT than with SFCT-2nd for 26-cm (10.2±1.3%) and 31-cm (7.0±2.5%), and the opposite for 36-cm (-4.2±2.5%). The highest average NPS spatial frequencies and TTF values at 50% (f50) values were found with DSCT. For all energy levels, f50 values were higher with SFCT-2nd than SFCT-1st for 26-cm (3.2±0.4%) and the opposite for 31-cm (-6.9±0.5%) and 36-cm (-5.6±0.7%). The lowest d’ values were found with SFCT-1st. For all energy levels, d’ values were lower with SFCT-2nd than with DSCT for 26-cm (-6.2±0.7%), similar for 31-cm (-0.3±1.9%) and higher for 36-cm (5.4±2.7%). In conclusion, compared to SFCT-1st, SFCT-2nd exhibited lower noise magnitude and higher detectability values. Compared with DSCT, SFCT-2nd had lower noise magnitude and higher detectability for the 26-cm but the opposite was true for the 36-cm.

Wood plastic composite usage and demands have increased due to chemical, and mechanical properties when compared to plastic materials. However, because of the possibility of structural and mechanical changes of the material when exposed to external environment more research needs to be done. In the present study yellow birch/HDPE composites materials made by injection molding were treated by zinc oxide and exposed to fungal rots. Mechanical properties of the composites were assessed by Tensile and Izod impact test. The impact energies of the samples loaded with 30 % ZnO-treated fibers and exposed to G. trabeum and T. versicolor decreased, compared to when samples were not treated with ZnO. The mechanical properties of all samples treated with ZnO and exposed to rot decreased which were reported as a decreased Young's modulus and impact energies. ZnO prevented mycelium proliferation which was nonexistent on samples. It has been noted that the decrease in mechanical properties of treated samples was due to NaOH used to dissolve the ZnO powder.

In this paper the application of the solid-state cooling based on barocaloric effect in the cold food supply chain is investigated. Barocaloric solid-state technology is applied to the final chain links of the cold food supply chain, regarding the steps of retail and domestic conservation. In this context a barocaloric cooler with regard to food needing to be kept at 5°C (273 K), in order to operate with a promising cooling technology that result energy efficient and environmentally friendly. The categories of food interested in the investigation are meets and fresh food products like soft cheese, yogurt, milk. The energy performances of the barocaloric system have been carried out and compared with a commercial vapor compression refrigerator of a similar size, both operating with R600a under the same working conditions. Basing on the following consideration one can conclude that barocaloric cooling is a favourable technology to be employed in the last link chains of the cold food supply chain if the system operates in ABR cycle at frequencies between 1.25 and 1.50 Hz with a regenerator made of acetoxy silicone rubber as solid-state refrigerant and 50%EG-50%water mixture as heat transfer fluid flowing at the optimal velocity of 0.15 m s-1 that guarantees an appropriate trade-off between the temperature span, the cooling power and the coefficient of performances. Under these conditions the barocaloric system overperforms the domestic vapor compression cooler operating with R600a.

This article explores matter collineations (MCs) of static plane-symmetric spacetimes, considering the stress-energy tensor in its contravariant and mixed forms. We solve the MC equations in two cases: when the energy-momentum tensor is nondegenerate and degenerate. For the case of degenerate energy-momentum tensor, we employ a direct integration technique to solve the MC equations, which leads to an infinite-dimensional Lie algebra. On the other hand, when considering the nondegenerate energy-momentum tensor, the contravariant form results in a finite-dimensional Lie algebra with dimensions of either 4 or 10. However, in the case of the mixed form of the energy-momentum tensor, the dimension of the Lie algebra is infinite. Moreover, the obtained MCs are compared with those already found for covariant stress-energy.

This paper offers a set of comprehensive guidelines aimed at facilitating the widespread adoption of hydrogen in the industrial hard-to-abate sectors. The authors begin by conducting a detailed analysis of these sectors, providing an overview of their unique characteristics and challenges. The paper delves into specific elements related to hydrogen technologies, shedding light on their potential applications and discussing feasible implementation strategies. By exploring the strengths and limitations of each technology, the paper offers valuable insights into its suitability for specific applications. Finally, through a particular analysis focused on the steel sector, the authors provide in-depth information on the potential benefits and challenges associated with hydrogen adoption in this particular context. By emphasizing the steel sector as a focal point, the authors contribute to a more nuanced understanding of hydrogen's role in decarbonizing industrial processes and inspire further exploration of its applications in other challenging sectors.

The established classical method of treating oil refinery effluent is flotation followed by biological treatment. Membrane bioreactors (MBRs) offer more advanced treatment, producing a clarified and potentially reusable treated effluent, but demand robust pretreatment to remove oil and grease (O&G) down to consistent, reliably low levels. An analysis of a full-scale conventional oil refinery ETP based on flotation alone, coupled with projected performance, energy consumption and costs associated with a downstream MBR, have demonstrated satisfactory performance of flotation-based pre-treatment. The flotation processes, comprising an API separator followed by dissolved air flotation (DAF), provided ~90% removal of both total suspended solids (TSS) and O&G coupled with 75% COD removal. The relative energy consumption and cost of the pretreatment, normalised against both the volume treated and COD removed, was considerably less for the API-DAF sequence compared to the MBR. The combined flotation specific energy consumption in kWh was found to be almost an order of magnitude lower than for the MBR (0.091 vs 0.86 kWh per m3 effluent treated), and the total cost (in terms of the net present value) around one sixth that of the MBR. However, the nature of the respective waste streams generated and end disposal of waste solids differs significantly between the pretreatment and MBR stages.

Concept sustainable of banking is based on principle realization growth and profit for the bank and shareholders, but only with achievement social goals, as and care for conservation life environment. Providing new ones banking service and creation new ( green ) banking jobs, except for _ profitable, they achieve and spreads social and ecological goals, chances are with creation competitive advantages, both in countries Western Balkans observed in the work, so and in all countries of the world In this one work we will focus on analysis macroeconomic parameters in countries Western Balkans works tests influence selected indicators on performance banking system, with special in retrospect on social and component protection life environment. The results indicate that rate unemployment the most significant indicator potentially risky events for bankers, as and banks they are not recognized in national conservation strategies _ life environment which are in WB countries currently on strength. Accordingly, the former is necessary to carry out education foreign affairs, and in parallel to promote green loans like they live and in the long term more favorable of traditional loans, with update the existing one regulatory frame in the domain protection life environment.

Owing to the escalating adoption of IoT systems across various domains, the demand for mobile and wireless power sources has surged. Although conventional batteries typically serve as energy storage components, the current low-power consumption devices necessitate eco-friendly alterna-tives. In this study, we designed, fabricated, and characterized an energy harvesting device that repurposes mechanical vibrations. A three-beam design was employed to harvest energy across a broader range of potential frequencies. Finite element models were simulated to ascertain the first bending moment for both sets of beams. A nanostructured piezoelectric multilayer film made of ZnO was deposited onto an AISI 304 steel substrate, and a photosensitive resin seismic mass was implemented. Low-cost techniques generating minimal environmental waste were leveraged in the fabrication process. The piezoelectric film was deposited using a spray nebulization technique involving recycled materials and cost-effective equipment. Micrographs of the layers unveiled the presence of nanospheres with diameters of 250 nm. Employing a custom-made shaker, output voltages of 1.08 V and 180 mV, and power outputs of 1.849 µW and 16.2 nW were achieved for each set of beams. The electrical characterization was conducted using a custom-made shaker, repurposing materials for this objective.

Taking a socio-technical perspective, I focus on solar businesses (niche market actors) in Iran. As one of the key stakeholder groups whose business prosperity is tied to the development of solar PV, they play a crucial role in accelerating the energy transition. Given the incumbent fossil-based electricity sector in Iran and the least enabling policies, I am first interested to find (i) the main drivers and barriers of solar businesses; and (ii) the roles these solar businesses play in bringing solar PV deployment forward in Iran. I collected the data via 20 semi-structured interviews with solar businesses in Golestan, Guilan, Tehran, Khorasan Razavi, and Eastern Azerbaijan Provinces in Iran. Taking an inductive approach, I considered sustainability transition and social acceptance theories as sensitising concepts to investigate common and specific points of solar business acceptance in Iran. I find ecological awareness, belief in intergenerational justice, and willingness to innovate, as the main intrinsic drivers and socioeconomic opportunity and tackling the energy imbalance as extrinsic drivers; while the lack of a common vision with the energy governors, and the low knowledge of solar PV among the customers, escalating prices, and challenges to accessing good quality solar equipment are the most prior obstacles. Moreover, I understand educating people, driving the innovative deployment of solar PV, and facilitating the diffusion of it, as the major roles of solar businesses in Iran. I find that the sustainability transition literature overlooked the key role of solar businesses specially in fossil-based and developing economies. My findings suggest that the positive intrinsic mechanisms among the solar businesses, in combination with better-enabling policy frameworks and external factors, like lifting the sanctions and joining the global energy market, climate change mitigation commitments and standards, can help solar businesspeople to lead and accelerate solar PV development in Iran.

From the standpoint of Neoliberal Institutionalism, this study explores Malaysia's participation in activities that make energy the topic and/or object of foreign policies, whether through bilateral or multilateral engagements. This research, which aims to evaluate the relevance of energy in Malaysia's economy and diplomacy and to explain Malaysia's reason for its involvement in these cooperations, is necessary because of Malaysia's growing involvement in the global energy market. Information for this study was gathered from a variety of government sources, interviews, published statistical data, and previous studies. The study demonstrates how vital energy is to Malaysia's economy. The Lao PDR-Thailand-Malaysia-Singapore Power Integration Project (LTMS-PIP) initiative, in which Malaysia is participating, is evidence of the viability of multilateral power commerce in the area. The Peninsula Gas Utilisation (PGU) pipeline in Peninsular Malaysia and the Four-Fuel Diversification Policy 1981 (4FDP 1981), which increases natural gas utilisation, are related to Malaysia's participation in the Malaysia-Thailand Joint Development Area (MT-JDA). Malaysia would want to think about streamlining its energy administration.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

For a decade, the studies of dynamic control for unmanned aerial vehicles took a large interest, where drones as a useful technology in different areas were always suffering from several issues like instability-high energy consumption of batteries - inaccuracy of tracking targets. Different approaches are proposed for dealing with the non-linearity issues which present the most important features of this system. This paper describes our focus on the most common control strategies, known as model predictive control MPC, by developing a model based on the sensors embedded in our Tello quadrotor used for indoor purposes. The original controller of Tello quadrotor is supposed to be a slave, where the designed model predictive controller is created in MATLAB and imported to another embedded system, considered as a master; the objective of this model is to track the reference trajectory, almost keeping the stability of the system and ensure the low energy consumption. In the first part, a profound description of the modelling process of a dynamic model for drones is presented, explaining the design of MPC controller with both linear and non-linear strategies built in MATLAB. In the final part, simulation and results are discussed regarding its behaviour and performance, highlighting the MPC model's important role on drones' energy consumption profile.

Monte Carlo Filtering (MCF) is one of the methods of Experimental Statistical Energy Analysis (E-SEA), which allows the correction of a negative LF (Loss Factor). In this article, a modification of the MCF method, called DESA (Diagonal Extension of the Search Area), is proposed. The technique applies a non-uniform extension of the search area when generating a population of normalized energy matrices. The degree of expansion of the search area is controlled by the Diagonal Penalty Factor (DPF). The authors demonstrated the method's effectiveness on a system that could not be identified in several frequency bands by the classical MCF method. After applying DESA, it was possible to fill in the problematic bands that were missing CLF and DLF values. The paper also proposes a way to minimize the errors introduced by using overly high DPF values.

We obtain exact solutions to the field equations for 5 dimensional LRS Bianchi type-I spacetime in $f(R,T)$ theory of gravity where specifically the following three cases are considered: (i) $f(R,T)=\mu(R+T)$, (ii) $f(R,T)=R \mu + R T \mu^2$ and (iii) $f(R,T)=R+\mu R^2+\mu T$ where $R$ and $T$ respectively the Ricci scalar and trace of the energy-momentum tensor. It is found that the equation of state (EOS) parameter $w$ is governed by the parameter $\mu$ involved in the $f(R,T)$ expressions. We fine-tune the parameter $\mu$ to obtain effect of phantom energy in the model, however we also restrict this parameter to obtain a stable model of the universe. It is noted that the model isotropizes at finite cosmic time.

Strained layer superlattice (SLS) material system is being considered for large format, small-pitch and low-cost focal plane arrays for different applications. To address difficulties associated to focal plane arrays fabrication arising from mesa-isolation etching or complex surface treatment/ passivation process, planar structures have been considered. In this work, the recent progress on planar SLS photodetector using ion-implantation for device isolation is presented. The devices are presented here are nBn and pBn heterostructure InAs/InAsSb SLS photodetector, where Zn and Si were chosen as the ion implants, respectively. The electrical and optical performance of the devices were compared along with comparison with mesa-etched device, to give deeper view of the device performance.

We show that quantum mechanics can be constructed as a classical field theory that correctly describes all basic quantum effects, by combining the Maxwell and Dirac equations. It is shown that for a self-consistent union of the Maxwell and Dirac equations into a unified classical field theory, it is necessary to introduce an additional short-range tensor field, which compensates the intrinsic electrostatic field of the electron wave inside the atom. For the combined Maxwell-Dirac field, the stress-energy tensor is constructed. We show that in the nonrelativistic limit this theory naturally transforms into the self-consistent Maxwell-Pauli theory and allows describing all basic quantum effects in the framework of classical field theory without any quantization.

Unmanned aerial vehicles (UAVs)-based communication system is a promising solution to meet coverage and capacity requirements of future wireless networks. However, UAV-enabled communications is constrained with its coverage, energy consumption, and flying regulations, and the number of works focusing on the sustainability aspect of UAV-assisted networking has been limited in the literature so far. In this paper, we propose a solution to this limitation; particularly, we design a $Q$-learning-based UAV positioning scheme for sustainable wireless connectivity considering key constraints, that are, altitude regulations, non-flight zones, and transmit power. The objective is to find the optimal position of the UAV base station (BS) and minimize the energy consumption while maximizing the number of users covered. Moreover, a weighting mechanism is developed, where the energy consumption and number of users covered can be prioritized according to network/battery conditions. The proposed Q-learning-based solution is compared to the baseline k-means clustering method, where the UAV BS is positioned at the centroid location that minimizes the cumulative distance between the UAV BS and the users. The results demonstrate that the proposed solution outperforms the baseline k-means clustering-based method in terms of the number of users covered while achieving the desired minimization of the energy consumption.

The land-surface developments of the European Centre for Medium-range Weather Forecasts (ECMWF) are based on the Carbon-Hydrology Tiled Scheme for Surface Exchanges over Land (CHTESSEL) and form an integral part of the Integrated Forecasting System (IFS), supporting a wide range of global weather, climate and environmental applications. In order to structure, coordinate and focus future developments and benefit from international collaboration in new areas, a flexible system named ECLand which would facilitates modular extensions to support numerical weather prediction (NWP) and society-relevant operational services, e.g. Copernicus, is presented . This paper introduces recent examples of novel ECLand developments on (i) vegetation, (ii) snow, (iii) soil, (iv) open water/lake (v) river/inundation, and (vi) urban areas. The developments are evaluated separately with long-range, atmosphere-forced surface offline simulations, and coupled land-atmosphere-ocean experiments. This illustrates the benchmark criteria for assessing both, process fidelity with regards to land surface fluxes and reservoirs of the water-energy-carbon exchange on the one hand, and on the other hand the requirements of ECMWF’s NWP, climate and atmospheric composition monitoring services using an Earth system assimilation prediction framework.

Wrist-worn fitness trackers and smartwatches are proliferating with an incessant attention towards health tracking. Given the growing popularity of wrist-worn devices across all age groups, a rigorous evaluation for recognizing hallmark measures of physical activities and estimating energy expenditure is needed to compare their accuracy across the lifespan. The goal of the study was to build machine learning models to recognize physical activity type (sedentary, locomotion, and lifestyle) and intensity (low, light, and moderate), identify individual physical activities, and estimate energy expenditure. The primary aim of this study was to build and compare models for different age groups: young [20-50 years], middle (50-70 years], and old (70-89 years]. Participants (n = 253, 62% women, aged 20-89 years old) performed a battery of 33 daily activities in a standardized laboratory setting while wearing a portable metabolic unit to measure energy expenditure that was used to gauge metabolic intensity. Tri-axial accelerometer collected data at 80-100 Hz from the right wrist that was processed for 49 features. Results from random forests algorithm were quite accurate in recognizing physical activity type, the F1-Score range across age groups was: sedentary [0.955 – 0.973], locomotion [0.942 – 0.964], and lifestyle [0.913 – 0.949]. Recognizing physical activity intensity resulted in lower performance, the F1-Score range across age groups was: sedentary [0.919 – 0.947], light [0.813 – 0.828], and moderate [0.846 – 0.875]. The root mean square error range was [0.835 – 1.009] for the estimation of energy expenditure. The F1-Score range for recognizing individual physical activities was [0.263 – 0.784]. Performances were relatively similar and the accelerometer data features were ranked similarly between age groups. In conclusion, data features derived from wrist worn accelerometers lead to high-moderate accuracy estimating physical activity type, intensity and energy expenditure and are robust to potential age-differences.

Abstract. The purpose of this review is to investigate the nature of privacy concerns in the context of Smart Local Energy Systems (SLES) to understand how SLES providers can minimize both users’ concern, and cause for concern, around privacy. We conducted a rapid realist review and thematic framework analysis against Bronfrenbrenner’s socio-ecological model to understand privacy concerns in different contexts. A common privacy concern was that sharing detailed energy use data had the potential to reveal information about home life, and to intrude upon people’s sense of autonomy, choice and control. Evidence suggests that people are willing to accept newdata sharing technologies if the benefits of doing so are clear, anticipated, and mutually beneficial. Building trust, through increasing knowledge and understanding was a mechanism for overcoming privacy concerns, but this was mediated by the organization providing the information. Non-profit organizations were more trusted to ensure appropriate safeguards to privacy were in place. One key barrier to participation with good supporting evidence was that people can resist perceived intrusions on their privacy. This could be actively resisted by refusing to install data collection technologies or passively by non-participation in adapting energy use behaviors: both of which are necessary for SLES to achieve their goals of managing energy demand and building resilience in smart grids.

Peer-to-peer (P2P) energy trading – where energy prosumers transact directly between each other – could help enable transition to a low-carbon energy system. If it is to be supported in policy and regulation, it is important to anticipate the distributional impacts (or how it might impact segments of society differently). However, real-world evidence on P2P energy trading is currently extremely limited. To address this challenge in the short- to medium-term, this study aimed to explore what might be learned from the extensive body of research on a comparable offering in the accommodation sector: Airbnb. A realist review approach was employed to maximise transferability of findings, focused on what mechanisms are thought to lead to what distributional outcomes, in what contexts. On the basis of the review, participation in (and receipt of benefits of) P2P energy trading schemes would be expected to represent disproportionately those living in areas with network management challenges, who are younger and more highly educated. The review also raised the prospect of discrimination on the basis of characteristics such as race and gender where there are high levels of individual choice over who to trade with. Recommendations include monitoring, incentivising diversity, anonymization, and limiting trading choices.

Reliable prediction of sustainable energy consumption is the key to designing environmental friend buildings. In this study, two novel hybrid intelligent methods, namely grasshopper optimization algorithm (GOA), wind-driven optimization (WDO), and biogeography-based optimization (BBO) is employed to optimize the multitarget prediction of heating loads (HLs) and cooling loads (CLs) in heating ventilation and air conditioning (HVAC) systems. Concerning the optimization of applied hybrid algorithms, a series of swarm-based iteration is performed, and the best structure for the abovementioned methods are proposed. Besides, through sensitivity analyzing the relationship between the HLs and CLs and influential factors are highlighted. In other words, the GOA, WDO, and BBO algorithm are mixed with a class of feedforward artificial neural networks (ANN), which called MLP (multi-layer perceptron) to predict the HLs and CLs. According to the provided sensitivity analysis, the WDO with swarm size = 500 proposes the most proper-fitted terms after it has been combined with optimized MLP. The proposed WDO-MLP (training (R2 correlation=0.977 and RMSE error=0.183) and testing (R2 correlation=0.973 and RMSE error=0.190)) provided accurate prediction in the heating load and (training (R2 correlation=0.99 and RMSE error=0.147) and testing (R2 correlation=0.99 and RMSE error=0.148)) presents the most-fit prediction in the cooling load.

Wind power output is highly dependent on the wind speed at the selected site, therefore wind-speed distribution modeling is the most important step in the assessment of wind energy potential. This study aims at accurate evaluation of onshore wind energy potential in seven coastal cities in the south of Iran. Six Probability Distribution Functions (PDFs) were examined over representative stations. It has been deduced that the Weibull function, which was the most used PDF in similar studies, was only applicable to one station. Here, Gamma offered the best fit for three stations and for the other ones, Generalized Extreme Value (GEV) performed better. Considering the ranking of six examined PDFs and the simplicity of Gamma, it was identified as the effective function in the southern coasts of Iran bearing in mind the geographic distribution of stations. Besides, six turbine power curve functions were contributed to investigate the capacity factor. That was very important, as using only one function could cause under- or over-estimation. Then, stations were classified based on the National Renewable Energy Laboratory system. Last but not least, examining a range of wind turbines enabled scholars to extend this study into the practice and prioritize development of stations considering budget limits.

Efficient alternatives in energy production and consumption are constantly investigated by increasingly strict policies. In this way, the pollutant emissions that contribute to the greenhouse effect reduce and sustainability of the electricity sector increase. With more than a third of the world's energy consumption, buildings have great potential to contribute these sustainability goals. Additionally, with growing incentives in the Distributed Generation (DG) and Electric Vehicle (EV) industry, it is believed that Smart Buildings (SBs) can be a key in the field of residential energy sustainability in the future. In this work, an energy management system in SBs are developed to reduce the power demanded of a residential building. In order to balance the demand and power provided by the grid, microgrids such as Battery Energy Storage System (BESS), EVs and Photovoltaic Generation panels (PV) are used. Here, a Mixed Binary Linear Programming formulation (MBLP) is proposed to optimize the charge and discharge scheduling of EVs and also BESS. In order to show the efficiency of the model, a case study involving three scenarios and an economic analysis is considered. The results point a 65% reduction in peak load consumption supplied by grid and a 28.4% reduction in electricity consumption costs.

Due to an increase of the monocrystalline PV systems installations, for a drive towards the sustainable smart cities in the hot arid developing country such as Pakistan, pose challenges of the performance and degradation issues. Monocrystalline PV module efficiencies are declining and damaging under the continuous exposure to higher surface day-time temperatures in the different parts of the country. A MATLAB simulations were performed based on the validated mathematical approach. This paper investigates the hot arid surface temperature impacts on the performance of PV modules during the summer and winter seasons in Pakistan. The investigations are performed examining the power generating efficiency of the PV system. This paper also investigates the influence of installations of PV-system in the North, South, East and West regions of Pakistan. It was examined that the northern areas of Pakistan are more suitable for maintaining the long-term durability of the PV system. Investigations are performed for the peak summer and peak winter days. During summer months, cooling strategies have to be implemented to overcome the heating effects whilst reducing degradation effect on installed PV-system.

We report on the field testing datasets and performance evaluation results obtained from a commercial property-based visually-clear solar window installation site in Perth-Australia. This installation was fitted into a refurbished shopping centre entrance porch, and showcases the potential of glass curtain wall-based solar energy harvesting in built environments. In particular, we focus on photovoltaic (PV) performance characteristics such as the electric power output, specific yield, day-to-day consistency of peak output power, and the amounts of energy generated and stored daily. The dependencies of the generated electric power and stored energy on multiple environmental and geometric parameters are also studied. An overview of the current and future application potential of high-transparency, visually-clear solar window-based curtain wall installations suitable for practical building integration is provided.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

Radiation is the major driver of snowmelt, and hence its estimation is critically important. Net radiation reaching the forest floor is influenced by vegetation density. Previous studies in mid-latitude conifer forests have confirmed that net radiation decreases and then subsequently increases with increasing vegetation density, for clear sky conditions. This leads to existence of a net radiation minimum at an intermediate vegetation density. With increasing cloud cover, the minimum radiation shifts toward lower densities, sometimes resulting in a monotonically increasing radiation with vegetation density. The net radiation trend, however, is expected to change across sites, affecting the magnitude and timing of individual radiation components. This research explores the variability of net radiation on snow-covered forest floor for different vegetation densities along a latitudinal gradient. We especially investigate how the magnitude of minimum/maximum radiation and the corresponding vegetation density change with the site geographical location. To evaluate these, the net radiation is evaluated using the Forest Radiation Model at six different locations in predominantly white spruce (Picea glauca) canopy cover across North America, ranging from 45 to 66°N latitudes. Results show that the variation of net radiation with vegetation density considerably varies with latitude. In higher latitude forests, the magnitude of net radiation is generally smaller, and the minimum radiation is exhibited at relatively sparser vegetation densities, under clear sky conditions. For interspersed cloudy sky conditions, net radiation non-monotonically varies with latitude across the sites, depending on the seasonal sky cloudiness and air temperature. Latitudinal sensitivity of net radiation is lower on north-facing hillslopes than on south-facing sites.

Intended for the high voltage gain and wide-range operation of DC/DC converters for photovoltaic energy storage systems, a topology for four-phase interleaved DC/DC converters for photovoltaic power generation is proposed. This topology increases output voltage for output in series, and reduces the input current ripple by paralleling the input. Compared with traditional boost converter topology, the proposed topology reduces the output current and output voltage ripple, reduces the stress of the switching device, and reduces the withstanding voltage of the output capacitor under the premise of ensuring the boost ratio. Experimental results show that the maximum efficiency of the converter reaches 95.37%. Compared with traditional boost converters, the proposed converter offers obvious advantages in efficiency under the conditions that the output voltage and load are variable.

This paper assesses the behaviour of active distribution networks with high penetration of renewable energy sources when the control is performed in a centralised manner. The control assets are the on-load tap changers of transformers at the primary substation, the reactive power injections of the renewable energy sources and the active and reactive power exchanged between adjacent feeders when they are interconnected through a DC link. A scaled-down distribution network is used as testbed to emulate the behaviour of an active distribution system with massive penetration of renewable energy resources. The laboratory testbed involves hardware devices, real-time control, and communication infrastructure. Several key performance indices are adopted to assess the effects of the different control actions on the system operation. The experimental results demonstrate that the combination of control actions enables the optimal integration of a massive penetration of renewable energy.

CoO-ZnO-based composites have attracted considerable attention for the development of energy storage devices because of their multifunctional characterization and ease of integration with existing components. This paper reports the synthesis of CoO@ZnO (CZ) nanostructures on Ni foam by the CBD method for facile and eco-friendly supercapacitor applications. The formation of a CoO@ZnO electrode functioned with cobalt, zinc, nickel and oxygen groups was confirmed by X-ray diffraction, X-ray photoelectron spectroscopy, low and high-resolution of scanning electron microscopy, and transmission electron microscopy. The as-synthesized hierarchical nanocorn skeleton-like structure of CoO@ZnO-3h (CZ3h) electrode delivered a higher specific capacitance of 1136 F/g at a current density of 3 A/g with outstanding cycling stability, showing 98.3% capacitance retention over 3000 cycles in an aqueous 2 M KOH electrolyte solution. This retention was significantly better than that of other prepared electrodes, such as CoO (CO), ZnO (ZO), CoO@ZnO-1h (CZ1h), and CoO@ZnO-7h (CZ7h) (274, 383, 240 and 537 F/g, respectively). This superior capacitance was attributed to the ideal surface morphology of CZ3h, which is responsible for the rapid electron/ion transfer between the electrolyte and electrode surface area. The enhanced features of the CZ3h electrode highlight potential applications in high performance supercapacitors, solar cells, photocatalysis, and electrocatalysis.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

Building more energy efficient and sustainable urban areas that will both mitigate the effect of climate change and adapt for the future climate, requires the development new tools and methods that can help urban planners, architect and communities achieve this goal. In the current study, we designed a workflow that links different methodologies developed separately, to derive the energy consumption of a university school campus for the future. Three different scenarios for typical future years (2039, 2069, 2099) were run as well as a renovation scenario (Minergie-P). We analyse the impact of climate change on the heating and cooling demand of the buildings and determined the relevance of the accounting of the local climate in this particular context. The results from the simulations showed that in the future there will a constant decrease in the heating demand while for the cooling demand there will be a significant increase. It was further demonstrated that when the local climate was taken into account there was an even higher rise in the cooling demand but also that the proposed renovations were not sufficient to design resilient buildings. We then discuss the implication of this work on the simulation of building energy consumption at the neighbourhood scale and the impact of future local climate on energy system design. We finally give a few perspective regarding improved urban design and possible pathways for the future urban areas.

This paper aims to develop a low-cost, high-performance and high-reliability computing system to process large-scale data using common data mining algorithms in the Internet of Things computing. Considering the characteristics of IoT data processing, similar to mainstream high performance computing, we use a GPU cluster to achieve better IoT services. Firstly, we present an energy consumption calculation method (ECCM) based on WSN. Then, using the CUDA Programming model, we propose a Two-level Parallel Optimization Model (TLPOM) which exploits reasonable resource planning and common compiler optimization techniques to obtain the best blocks and threads configuration considering the resource constraints of each node. The key to this part is dynamic coupling Thread-Level Parallelism (TLP) and Instruction-Level Parallelism (ILP) to improve the performance of the algorithms without additional energy consumption. Finally, combining the ECCM and the TLPOM, we use the Reliable GPU Cluster Architecture (RGCA) to obtain a high-reliability computing system considering the nodes’ diversity, algorithm characteristics, etc. The results show that the performance of the algorithms significantly increased by 34.1%, 33.96% and 24.07% for Fermi, Kepler and Maxwell on average with TLPOM and the RGCA ensures that our IoT computing system provides low-cost and high-reliability services.

As renewable energy generation prediction system has been introduced into the energy trading market, making a model to accurately predict the quantity of solar photovoltaic (PV) energy generation has become a significant problem. Moreover, to encourage an accurate prediction of the quantity of energy generation, an incentive system has been implemented for those who predict the quantity of solar PV energy under the error rate of 8%. Therefore, it has become more important to investigate and analyze current prediction technology numerically and develop more advanced prediction system. In this study, we tried to develop a better model to improve the accuracy of solar PV energy generation quantity by comparing three models made with gradient boosting machine (GBM), Model 1, Model 2, Model 3 respectively. Model 1 was built with the whole training data set without any additional preprocessing. After conducting some additional preprocessing procedure to predict solar energy generation more accurately, we made Model 2 with the whole training data set and Model 3 with only upper 10% of energy generation capacity. To compare the accuracy of three models, normalized mean absolute error (nMAE) was used as an evaluation index. The nMAE of Model 1 was 9.64% while the Model 2 showed 8.41%. Also, Model 3, which was constructed with the training set of upper 10% energy generation capacity, outperformed with the nMAE of 8.08%. For further study, to check the effectiveness of models constructed with GBM, a time series model, autoregressive integrated moving average (ARIMA), was also built and the nMAE was compared.

In this paper, quasi-static axial compression tests are performed on the nodal Moso bamboos to study the size effect on energy absorption of the bamboos and the damage pattern of the multiple bamboo columns. Experimental results show that under the same moisture content, growth age and growing environment, the specific energy absorption (SEA) of the test samples increases with the increase of the out-diameter and thickness of the bamboo columns, indicating that size effect exists for energy absorption of the Moso Bamboos. For the multiple bamboo columns, there are mainly three failure modes for the constituent single bamboo columns: splitting above the node, splitting below the node and splitting through the node. Also, the tensile tests are conducted on three kinds of dog-bone shaped bamboo samples to investigate the macroscopic tensile fracture mode in the longitudinal direction of Moso bamboos. Results show that there is no direct relationship between the fracture pattern and moisture content of the bamboos, as well as the growth age of the bamboos. However, the tensile loading rate and the shape of the dog-bone shaped bamboo sample could affect the macroscopic fracture pattern of the bamboos in some cases.

The strength of laser joined metal and plastic hybrids is based purely on adhesion. Unpolar plastics like polypropylene depend solely on the mechanical adhesion while polar plastics like polyamide 6.6 develop covalent bonds with the metal. In this research the influence of different surface metallizations on the lap shear strength of laser joined hybrids was investigated. Sandblasted AISI 304 was used as base metal and reference. Aluminum and titanium coatings were deposited by the means of Arc-PVD. Polypropylene and polyamide 6.6 were utilized as polar und unpolar plastics. The lap shear strength of all hybrids with polyamide 6.6 was higher than the polypropylene samples. For all investigated variations of the laser power, scanning speed and the cohesive and adhesive failure modes, the samples joined with the sandblasted AISI 304 showed the highest lap shear strength. The reduction in lap shear strength for the coated samples was due to the increased difference in thermal conductivity between the plastics and the coating materials. This lead to increased warping and residual stresses. It can be concluded that the thermal properties of the metallization in laser joined metal and plastic hybrids has a high impact on the lap shear strength.

The European Union Green Deal aims at curbing planet-warming greenhouse gas emissions and introducing clean energy production. But to achieve energy efficiency, the opportunity cost of different energies must be assessed. In this article, we analyse two different systems for the treatment of wastewater that, at the same time, produce energy for its own operation. On the one hand, high-rate algal ponds system (HRAP) is considered; on the other hand, we study a conventional activated sludge system which uses photovoltaic power (AS+PV). This paper offers a viability analysis of both systems based on the capacity to satisfy their energetic consumption. In order to assess this viability, the probability of not achieving the energy consumption threshold at least one day is studied. The results point that the AS+PV system self-sufficiency is achieved using much lesser surfaces than those of HRAP system (for the former, less than 6.500 m2, for the latter 40.000 m2). However, the important AS capital cost makes still the HRAP system more economic, although storage provides a great advantage for using the AS+PV in locations where we have a lot of irradiance. This viability analysis, along with the opportunity cost analysis, will be used to assess these two projects devoted to the treatment of wastewater.

The research is devoted to the problem of noise generation during flights of supersonic civil aircrafts. The effect of a thermally stratified energy source used to control the flow past a pointed cylinder aerodynamic models on the nearfield and ground pressure signatures, as well as on the perceived loudness in decibels (PLdB) on the ground is evaluated. The fields of parameters and the dynamics of the drag forces are studied for different values of temperature in the layers of the thermally stratified energy source and for different number of layers in it. It has been shown that when performing the flow control at freestream Mach numbers 1.5-2 using thermally stratified energy sources with the number of layers from 2.5 to 7.5 and rarefaction parameters in the layers from 0.15 to 0.3, no additional noise impact on the ground is introduced. Thus, the simulations showed that changing the surface pressure signature due to drag reduction does not necessarily imply a change in the PLdB on the ground.

The atomic nucleus contains protons and neutrons surrounded by a structured electron cloud. Some combinations of protons and neutrons induce the nucleus to behave like a microscopic magnet, possessing a unique magnitude and orientation known as the nuclear magnetic moment (µ). When the numbers of protons and neutrons are both even then µ=0, but otherwise each nu-clide’s nuclear magnetic moment is unique. A second unique nuclear physical property relates to the nucleon binding energy (BE), which can be thought of as the energy between protons and neu-trons bound within the nucleus. The sequence of stable nuclides increases one nucleon at a time through 36Ar. The binding energy associated with the addition of each successive nucleon (∆BE) through this progression is unique. The hypothesis here is that the unique non-zero magnetic mo-ment and ∆ binding energy of each nuclide derive from its respective microscopic nuclear struc-ture, analogous to the way that the atomic physical properties of an element ultimately derive from its unique electron orbital structure. By extension, the identification of nuclear periodic pat-terns might eventually inform a theory of nuclear structure. The light, stable nuclides through 36Ar were arranged in ascending order according to atomic mass, and their nuclear magnetic mo-ments and binding energies were evaluated for periodic patterns. Fixed-period lengths from 4 through 18 nuclides per period were considered. These fixed periods, each of equal length, were stacked one upon the other and analyzed for vertical trends. The best evidence of periodicity in both µ and ∆BE converges precisely at the fixed 12-nuclide period. Implications for nuclear structure are discussed.

Here we mathematically model black holes and the early universe following dynamics similar to RLC electrical models, focusing on their similarities at the singularity. We use this mathematically modelling to hypothesize the evolution of an expanding universe as the result of a black hole collapse followed by its evaporation. Or model consists of several steps defined by: (1) the formation of a black hole following general relativity equations; (2) growth of the black hole modelled as a resistance-capacitance-like electrical circuit; (3) expansion of space-time following the disintegration of the black hole, modelled by RLC-like dynamics. In updating this article, version 2, we will expand by presenting three additional examples related to the theory of the generalization Boltzmann's constant in curved space-time and the theory of general and especial relativity. We will calculate the critical mass to produce a black hole in the LHC, the existence of a high temperature Bose-Einstein condensate and finally we will demonstrate the existence of a tangential force to the repulsion force in the disintegration of subatomic particles. In the update of this article, version 3, we will expand to develop two examples. First, we will present the relationship between M-theory, extra dimensions with the theory of the generalization of Boltzmann's constant in curved space-time. Secondly, we will propose the idea of ​​updating the Lambda-CDM model, considering the primordial gravitational waves to correctly describe the evolution of the universe.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

It is commonly held that gravitation is a major force field influencing matter. Existing models regard gravitational interaction as a singular weak force; the weakest among the four fundamental forces defined in physics. Recent experimental findings, in both controlled laboratory experiments and natural occurrences, nevertheless, have unveiled the presence of a gravitational repulsion alongside gravitational attraction in the universe. This series of studies reveals that the observed gravitational force results from two immensely powerful distinct forces—gravitational repulsion and attraction—nearly equal and opposing thus in a state of near equilibrium in nature. While the theory of 'Universal Gravitation' established the proportionality of the gravitational force to mass, the recognition of gravitational repulsion force proportional to the temperature as a manifestation of thermal energy has only emerged from present experimental insights. Furthermore, the imbalance between these two forces has been identified as the Newtonian force, initiating the motion of an object. It provides a compelling explanation for the accelerating expansion of the universe: during atomic fusion in stars, a portion of mass is converted into energy. This process increases the energy and decreases the mass of stellar objects. The increase in energy enhances the repulsive force among them, while the reduction in mass diminishes their gravitational attraction, leading to the accelerating expansion of the universe.This paper introduces a model elucidating the characteristics of gravitational forces and the transmission of energy within matter through the concept of 'Gravitational Currents.' A set of postulates is formulated to elucidate the interaction of gravitational fields with matter and the presence of gravitational currents. The discussion is supported by experimental evidence substantiating these concepts.In this series of experiments, a gyroscope - a standard apparatus in the scientific community with a spinning wheel mounted at one end of a freely pivoted rod having full degrees of freedom - is utilized. When the wheel is set in rotation, the rod carrying the wheel precesses[1] around the vertical axis at the pivoted end, while levitating in free space defying the Earth's gravitational attraction. This paper establishes that the conventional explanation involving the cross product of two vectors—the torque due to weight and the angular force (change of angular momentum) of the wheel—fails to account for the observed revolving and lifting forces. Instead, it is demonstrated that these forces result from the upward shear force (which is the lifting force in this case) generated within the axis of the rod and the wheel itself. This phenomenon is attributed to the flow of energy, conceptualized as gravitational current, within the axial rod in the Earth's gravitational field. The described process can be envisioned as a gravitational motor with gravitational current flowing through matter in a gravitational field.The results of the experiments substantiate the conclusion that there exist two fields defined as the intrinsic field and the natural force fields. The intrinsic gravity field is innate (linked) to every object, matter or entity in the universe, and it is dispersed in all directions in free space independent of other entities. The actual force fields manifest between any two objects in the universe once they become cognizant of each other's existence through their intrinsic fields.The inherent force field exhibits a preference/tendency for existence within a medium rather than in free space, akin to the way a magnetic field runs within ferromagnetic materials rather than in open space. If external force fields pass/runs through the medium, it affects the internal force fields of the medium, depending on the magnitudes and the directions of the external force fields and intrinsic force fields. This implies that energy moves through the force field, and under the influence of the gravitational field, this energy flow can be conceptualized as a gravitational current.Gravitational waves and electromagnetic waves share similarities in their roles in transmitting energy through open space. The potential for an analogy within a unified theoretical framework connecting electromagnetic fields and gravitational fields has surfaced, echoing Einstein's attempted unified theory proposed in 1916. The paper delves into the parallels between electromagnetic motors and gravitational motors.Furthermore, alongside the concept of gravitational currents addressed in this paper, the research also elucidated a precise definition of the [Newtonian/mechanical] “force” and mechanism for its origination and function, termed: Intrinsic Energy Spin Force (IESpinF). The analysis presented here demonstrates that the Newtonian/mechanical force arises from a perturbation or imbalance within the equilibrium of gravitational IESpinF, which includes both repulsion and attraction forces. [1] One of the main properties of gyroscopic action is “precession”. Precession is a change in the orientation of the rotational axis of a rotating body. If the axis of rotation of a body is itself rotating about a second axis, that body is said to be precessing about the second axis.

As an irreplaceable ecological barrier, the ecological conservation developing area (ECDA) is vital for the integrated construction of urban and rural areas, and optimization and adjustment of industrial structure. Developing green agriculture is the foundation and guarantee for improving the rural ecological environment and meeting the increasing needs of farmers′ income. Issued by the Chinese government, No. 1 Central Document stated the necessity of promoting agricultural green development (AGD) and the related technologies in dealing with ecological pressure and resource shortages, especially for large cities like Beijing. However, few empirical studies have conducted on spatiotemporal variations of AGD in ECDA of large cities. Based on the green agricultural traits of Beijing and the accessible data, we evaluate AGD and analyze its spatial and temporal heterogeneity of Beijing ECDA by constructiing a framework with 13 indicators. The weight coefficients of AGD indicators were calculated by the projection pursuit method, with the district panel data from 2006 to 2016. The results demonstrated that energy consumption is a vital factor of green agriculture production, and agricultural output value per unit of the arable land area is the key to the green agricultural revenue. From 2006 to 2016, the AGD index of ECDA had an increasing trend till 2012, followed by a decreasing tendency. The AGD index of the northern region is higher than the southern of ECDA. The obstacle degree model was used to verify AGD limiting factors. They were poor infrastructure, slow agritourism, low labor productivity, and low resource utilization efficiency that varied by districts in ECDA. Given these findings, our study is conducive to the AGD evaluation at the district (county) level for ECDA of large cities and also provides important policy implications.

A steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings and multistory housing. To assess the seismic performance of buildings with steel damper columns, the peak displacement of the whole building and the energy dissipation demand of the dampers must be evaluated. This article proposes an energy-based prediction procedure for the peak and cumulative response of an RC frame building with steel damper columns. The proposed procedure considers two energy-related seismic intensity parameters, namely the maximum momentary input energy and the total input energy. The peak displacement is predicted considering the energy balance during a half cycle of the structural response, using the maximum momentary input energy. The energy dissipation demand of the dampers is then predicted considering the energy balance during a whole response cycle using the total input energy. The local responses (e.g., peak drift, maximum plastic rotation of beams, maximum shear strain, and energy dissipation demand of dampers) are predicted using pushover analysis. Numerical analysis results for 8- and 16-story RC buildings show that the proposed prediction method achieves satisfactory accuracy.

The purpose of this research was to analyze the moderating effect of clean energy innovation on the relationship between corporate carbon footprint and corporate profits in those industrial sectors associated with high demand for fossil fuels in which it is "hard to abate" CO₂e emissions. It used a longitudinal research design, in particular a panel study under a structural equation modeling (SEM) approach, based on partial least squares. For the longitudinal moderation analysis, this research employed the Bayesian method by defining a multiple-indicator latent growth curve model (B-LGC model). A global sample was used consisting of 7,827 firm-year observations between 2015 and 2021 corresponding to 167 international firms. The results revealed a very significant impact of the corporate carbon footprint on corporate profits. Likewise, the results showed that innovations in clean energy, when measured as the consumption of renewable energy, positively moderates the relationship between the greenhouse gas emissions from the value chain associated with Scope 3 of the Greenhouse Gas (GHG) Protocol, and the gross profit margin obtained. Besides the academic contribution represented by the moderating effect of clean energy innovation, these findings imply that a more detailed understanding of the emissions of the entire value chain (Scope 3 CO₂e) by executives and managers of high emitting CO₂e companies represents an effective mechanism to obtain higher profits, create competitive advantages and, at the same time, achieve a net zero emissions strategy. More importantly, public policy makers will be able to use these results to revise CO₂e-related policies paying more attention to the Scope 3 CO₂e emissions produced by these companies, to formulate regulatory and control mechanisms that stimulate clean energy innovation.

This article explores the multifaceted argument for Scottish independence, emphasizing Scotland's historical context, cultural identity, and the potential benefits of rejoining the European Union (EU). It begins with a historical overview, tracing Scotland's deep roots in independence and its eventual union with England in 1707, which, despite economic benefits, subordinated Scottish interests to those of England. The article argues that Scotland's distinct identity and ongoing desire for autonomy justify a renewed push for independence. Reuniting with Europe is presented as a key advantage, offering Scotland access to the EU's single market, financial support, and a platform for political influence. Additionally, independence would empower Scotland to harness its renewable energy resources, develop tailored economic policies, and uphold its tradition of social justice. However, the article also acknowledges the unique challenges Scotland faces, particularly in formulating citizenship policies amidst the legacy of English imperialism. Ultimately, the article posits that despite these challenges, independence offers Scotland a path to realizing its full potential as a sovereign nation committed to democracy, equality, and cooperation.

In this work, the author employs the quantum hydrodynamic formalism to achieve the geometrization of spacetime for describing the gravitational interaction within the framework of quantum theory. This approach allows for the development of an equation of gravity that is mathematically connected to the fermion and boson fields. This achievement is accomplished by incorporating two fundamental principles: covariance of the quantum field equations and the principle of least action. By considering these principles, a theory is established that enables the calculation of gravitational corrections to Quantum Electrodynamics, and potentially, to the standard model of particle physics as well. The theory also provides an explanation for two phenomena: the existence of a cosmological pressure density similar to quintessence, that is compatible with the small value of the observed cosmological constant, and the breaking of matter-antimatter symmetry at high energies offering insights into why there is an imbalance between the two in the early universe. In the cosmological modeling of the theory, there exists a proposal to account for the formation of supermassive black holes that are accompanied by their own surrounding galaxies, without relying on the process of mass accretion. The model, in accordance with recent observations conducted by the James Webb Space Telescope, supports the notion that galactic configurations were established relatively early in the history of the universe, shortly after the occurrence of the Big Bang.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

An attempt is made to model the atomic nucleus as a combination of bound and free or unbound nucleons. Due to strong interaction, bound nucleons help in increasing nuclear binding energy and due to electroweak interaction, free or unbound nucleons help in decreasing nuclear binding energy. In this context, with reference to proposed 4G model of final unification and strong interaction, recently we have developed a unified nuclear binding energy scheme with four simple terms, one energy coefficient of 10.1 MeV and two small numbers 0.0016 and 0.0019. In this paper, by eliminating the number 0.0019, we try to fine tune the estimation procedure of number of free or unbound nucleons pertaining to the second term with an energy coefficient of 11.9 MeV. It seems that, some kind of electroweak interaction is playing a strange role in maintaining free or unbound nucleons within the nucleus. It is possible to say that, strong interaction plays a vital role in increasing nuclear binding energy and electroweak interaction plays a vital role in reducing nuclear binding energy. Interesting observation is that, Z can be considered as a characteristic representation of range of number of bound isotopes of Z. For medium, heavy and super heavy atoms, beginning and ending mass numbers pertaining to bound states can be understood with 2Z+0.004Z^2 and 3Z+0.004Z^2 respectively. With further study, neutron drip lines can be understood. Based on this kind of data fitting procedure and by considering the mass ratio of pions and electroweak bosons, existence of our 4G model of electroweak fermion of rest energy 584.725 GeV can be confirmed confidently.

Temperature differences between the atmosphere and river water allow rivers to be used as a hydrothermal energy source. The river-water heat pump system is a relatively non-invasive renewable energy source; however, effluent discharged from the heat pump can cause downstream temperature changes which may impact sensitive fluvial ecosystems. In this study, the water temperature recovery distance of the effluent was estimated for a river section in the Han River Basin, Korea, using the heat transfer equation and the Environmental Fluid Dynamic Code (EFDC) model. Results showed that, compared to the EFDC model, the heat transfer equation tended to overestimate the water temperature recovery distance due to its simplified assumptions. The water temperature recovery distance could also be used as an objective indicator to decide the reuse of downstream river water. Furthermore, as the river system was found to support an endangered fish species that is sensitive to water environment changes, care should be taken to exclude the habitats of protected species affected by water temperatures within water temperature recovery distance.

The thermoelectric generator (TEG) has much potential as a renewable energy technology that could be used in ocean thermal energy conversion (OTEC). This technique employs TEGs and heat exchangers as substitutes for the intricate elements found in conventional OTEC systems, including pressure valves, evaporators, condensers, and turbine generators. By harnessing the temperature difference between warm surface seawater and cold deep seawater, it facilitates the conversion of this thermal gradient into electrical energy. This study used computer simulations to look at and compare three different types of heat exchangers: a cavity-type heat exchanger, a heat exchanger with flat fins, and a heat exchanger with longitudinal vortex generators (LVGs). The objective was to evaluate the influence of these designs on the thermoelectric conversion performance when implemented in OTEC systems. The study's findings indicate that using heat exchanger configurations featuring flat fins, or LVGs, enhances the efficiency of thermal energy transfer from warm seawater to TEGs, resulting in a notable enhancement in the output power of TEGs. Furthermore, the efficiency of TEG thermoelectric conversion is influenced by varying seawater flow rates in relation to the performance of flat fins and LVGs. In contrast to the cavity-type heat exchanger, the utilization of a heat exchanger equipped with flat fins has been found to yield a notable enhancement in the output power of TEGs by approximately 22.92%. Furthermore, this configuration demonstrates a substantial improvement in thermoelectric conversion efficiency, exhibiting an increase of around 40.01%. These improvements are observed under certain conditions pertaining to flow rates and fin heights. Utilizing heat exchangers equipped with LVGs has been found to enhance the output power of TEGs by 13.02% and improve the overall thermoelectric conversion efficiency by 17.72%. These improvements are observed under certain conditions, including specific flow rates, LVG tilt angles, and locations.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

The paper presents the final results from the research project “Urban Abacus of Building Energy performances (Abaco Urbano Energeticodegli Edifci – AUREE)” aimed at supporting the renovation and energy efficiency enhancement of urban building heritage financed by the “Ricerca Sistema Elettrico (MISE) program”. The crux of AUREE project is a Web – GIS GeoBlog portal with customized semantic dashboards aimed at sharing information on urban built environment and promoting the participation of local stakeholders to its improvement. As the latest development of this research, a workflow integrating the AUREE portal with BIM authoring and an open source IoT platform has been implemented and applied to an experimental case study concerning a public building in Carbonia (Italy). The headquarters of the sustainable energy research center Sotacarbo was selected as case study. The presented results proved that it was possible to create an open system, which could be easily consulted by "non-expert" users as well, to make available real-time monitoring data obtained from IoT sensors measuring the energy consumption, the indoor environmental conditions and the usage profiles of public buildings. The proposed open system could also be suitable to be later used as an effective tool to support the rising “energy communities”.

A major public health emergency has been created by the COVID-19 pandemic, which is brought on by the SARS-CoV-2 virus. Due to its crucial function in viral replication, the primary protease (Mpro) of the virus is a prime target for therapeutic research. In this study, we used molecular modeling and molecular dynamics simulations to examine the potential therapeutic uses of Mpro inhibitors for the treatment of COVID-19. Using induced fit docking and molecular dynamics simulations, we confirmed the top compounds after screening a library of compounds for their ability to bind to Mpro. Simulation interaction diagrams were used to investigate protein-ligand interactions, and MM-GBSA was used to determine binding energies. The Swiss ADME server was used to predict ADME properties. According to our findings, numerous substances are strong COVID-19 medication candidates since they have excellent ADME features and high binding affinities. This work serves as a foundation for additional experimental research and drug development initiatives aimed at Mpro.

The growing demand for clean energy transitions has become increasingly significant, with solar energy emerging as one of the most prominent clean energy resources contributing to this effort. However, there remains limited knowledge regarding the economic feasibility of solar project development across different geographic locations and scales. This study introduces a comprehensive economic analysis framework to assess the economic viability of residential and utility-scale solar projects, using California, Tennessee, and Texas as case studies. The economic assessment is conducted through a cost-benefit analysis that adopts a full life-cycle approach, encompassing phases from permitting to demolition for both scales of solar projects. We found that utility-scale solar projects generally offer more favorable investment return ratios compared to residential projects, despite the absence of land acquisition costs and lower initial capital expenditures for the latter. Furthermore, the incorporation of energy storage solutions, such as Battery Energy Storage Systems (BESS), is shown to be essential for improving the efficiency of residential solar energy usage, with efficiency gains of up to 50%. Finally, region-specific strategies, including net metering policies, electricity retail market structures, and the promotion of solar adoption, play a crucial role in enhancing the financial viability of solar projects for both residential and utility scales.

In this paper, we make an attempt to estimate the famous Avogadro number with programming logics written in Python associated with advanced nuclear binding energy formulae. Average rest mass of nucleon, nuclear binding energy per nucleon and electron rest mass seem to play a vital role in estimating the unified atomic mass unit and Avogadro number. Interesting point to be noted is that, Avogadro number seems to be the inverse of the Unified atomic mass unit. With further study, it seems possible to estimate the unified atomic mass unit and Avogadro number accurately. Our interesting observation is that, short range strong nuclear force seems to have a vital role in deciding the accuracy of Avogadro number. For that purpose one may consider AI techniques along with newly observed atomic nuclides and their nuclear binding energies. For Z=6 to 118 and A_low=2Z and A_upper=3.5Z, estimated average value of Avogadro number is $N_{Average} \cong 6.01938 \times 10 ^{26}$. Considering the saturation of nuclear binding energy, at Z=26, $N_{Z=26} \cong \left(6.02229 \textrm{to} 6.02285\right) \times 10 ^{26}$. At academic level, our proposal can be given a chance as a case study. It is planned to develop a web application for this purpose.

As renewable energy generation prediction systems have been introduced into the energy trading market, accurate prediction of solar photovoltaic (PV) energy generation has become a crucial challenge for ensuring stable trade of variable energy. Therefore, it is essential to quantitatively investigate and analyze current prediction technology and develop more advanced prediction systems. In this study, three models for predicting PV energy generation were investigated. Multiple regression, random forest, and gradient boosting machine (GBM) models were con-structed for 15 utility-scale power plants throughout South Korea. Model performance was evaluated in terms of root mean square error (RMSE) and mean absolute error (MAE). The multiple regression-based model had an RMSE of 12.00% and MAE of 9.06%. The random forest model had an RMSE of 11.69% and MAE of 8.61%. The GBM model had an RMSE of 11.34% and MAE of 8.18%, indicating its superior accuracy among the three models in predicting PV energy generation. These findings provide valuable insights that may contribute to the development of advanced PV energy generation models and their application in grid operations.

This study describes the energy-momentum density tensor of matter. The main focus is on discussing the conservation laws of the general theory of relativity.

Maxwell's energy-momentum tensor cannot be used as is in Einstein's equation for general relativity in the presence of sources. In this case, its four-divergence is non-zero, whereas the tensors in the equation must have this characteristic. However, the sun emits streams of ionized particles, gases are present within galaxies, material transfers in the form of ionized plasma can occur in binary star systems, and so on. These charges cannot be neglected in the study of space-time in these regions. Here, we present a modified version of this tensor that eliminates this flaw, provided that the potentials satisfy the Lorenz gauge. The distribution of sources will also be analyzed in light of fluid mechanics, allowing us to account for its influence in terms of generated pressure.

Optimization techniques are pivotal across various scientific domains, typically involving solving problems among feasible alternatives based on specific goals, alternatives, or constraints. In mathematical optimization, traditional methods like Simulated Annealing (SA) do not guarantee finding global minima/optima, especially in cases that contain high dimensions in objective functions. This paper introduces a novel approach where a free-energy driven self-adaptive SA algorithm is designed to handle such cases by incorporating free-energy costs within the Metropolis-Hastings framework. This algorithm not only dynamically adjusts to the changing dimensions of the objective function, but it also enhances a faster optimization process. Furthermore, as examples we demonstrate its capability on a convex unimodal function and the non-convex Rastrigin function, revealing faster convergence to search global minima compared to standard SA algorithm. At last, parameter estimation of noisy exponential data has been executed by our Simulated Annealing driven by the Free-Energy (SAFE) algorithm. Our results suggest that this novel approach may significantly improve optimization speed and accuracy, providing a robust tool for complex multidimensional optimization problems.

Quantum machine learning applications have become viable with the recent advancements in quantum computing. Merging ML with the power of quantum computing holds great potential for data-driven decision-making, as well as the development of more powerful models capable of handling more complex datasets with faster processing time. This area offers potential for improving the accuracy of real-time forecasting renewable energy production. However, the literature on this topic is sparse. Addressing this knowledge gap, this study aims to design, implement, and evaluate the performance of a quantum neural network forecast model for solar irradiance up to 3-hours ahead. The proposed model was compared with Support Vector Regression, Group Method of Data Handling, and Extreme Gradient Boost classical models. Using the best quantum neural network configuration found, the proposed framework could provide competitive results when compared to its competitors, considering forecasting intervals of 5- to 120-minutes ahead, where it was the fourth best-performing paradigm. For 3-hours ahead predictions, the QNN was able to overcome its clas-sical counterparts, but the XGBoost. This fact can be an indication that the quantum model may identify and retrieve relevant spatiotemporal information from the input dataset in such a manner not attainable by the current classical approaches.

Previous research has proven that one of the fundamental requirements for ensuring increased profitability and economic competitiveness of offshore-based projects is co-locating different technologies within the same marine space. This paper presents a number of techno-feasibility analyses for floating offshore technologies for the Maltese Islands, located in the Central Mediterranean Sea. The first part compares the feasibility of offshore-based solar photovoltaic prices with those onshore, taking into consideration Malta’s land prices. The second part considers the use of a novel floating breakwater design that integrates energy storage. The breakwater is used to create a sheltered water area in deep waters for a multi-use marine park. Different revenue streams for the floating break water are considered, including renting the sheltered marine space out to operators of floating solar farms, aquaculture cages and vessel berthing facilities, and the provision of energy storage services. It is found that the combined income from the multiple revenue streams is still insufficient to justify the investment and that financially support from Government is essential to render the floating breakwaters viable.

Based on recent progress in cosmological thermodynamics, we are presenting a new ther- modynamic formulation of the Friedmann equations, as well as for other similar equations put forward in the literature from different solutions to Einstein’s field equation. Since the CMB temperature has been measured much more accurately than the Hubble constant, we demonstrate that the thermodynamic formulation of the Friedmann equation dramatically narrows down the acceptable range for the mass-energy density in the universe.

Symmetry-breaking is a phenomenon that is observed in various contexts, from the early universe to complex organisms, and is considered a key puzzle in understanding the emergence of life. The presence of enantiomeric amino acids and proteins highlights its critical role. However, the origin of symmetry-breaking has yet to be comprehensively explained, particularly from an energetic standpoint. This article explores a novel approach by considering energy dissipation, specifically lost free energy, as a crucial factor in elucidating symmetry-breaking. Through a thorough thermodynamic analysis applicable to enantiomeric systems at various scales, from elementary particles to aggregated matter like crystals, we present experimental findings that establish a direct correlation between non-equilibrium free energy and energy dissipation during formation processes. Results emphasize the pivotal role of energy dissipation not only as an outcome but as the trigger for symmetry-breaking. This insight suggests that understanding the origins of complex systems, from cells to living beings and the universe itself, requires a lens focused on non-equilibrium processes, ultimately facilitating the formation of non-racemic systems.

In order to the effect of hydrated phase change materials on suppressing coal spontaneous combustion, the thermogravimetric experiment and reaction activation energy analysis experiment were used to explore the changes of combustion characteristic, parameters characteristic temperature and activating energy of gas coal, long flame coal, meagre coal, and lean coal before and after adding hydrated phase change materials. The research results showed that hydrated phase change materials increased the coal samples’characteristic temperature point and have effective inhibitory effects on different stages of oxidation process.However, the effect was best at low temperatures, as hydrated phase change materials undergo phase change and absorb heat when heated at low temperatures, isolating coal from contact with oxygen. The activating energy increased by 1.138 KJmol-1～23.048 KJmol-1 and the mass loss reduced by 1.6%～9.3% after the inhibition of the coal sample,indicating that the oxidation rate of various coal samples can be slowed down and the spontaneous combustion can be suppressed by using hydrated phase change materials.At the same time, this material can also reduce the combustibility index of meagre coal and lean coal, as well as the comprehensive combustion index and maximum loss rate of long flame coal and gas coal.

This study aimed to increase the energy independence of buildings by utilizing solar energy to produce renewable energy. The subject of this study was a shading structure installed in an outdoor space to provide solar energy. Solar panels were applied to the shaded structures to generate energy actively. The solar panels were designed to be moved according to the optimal tilt angle each month to produce the optimal renewable energy. The architectural design of the shading structure and the energy simulation of the solar panels were conducted using a parametric design. The results of the energy simulation showed the generation of 31,570 kWh· year−1 of renewable energy. This amount of energy is 10% higher than that produced by fixed solar panels. Thus, the moving solar panel system developed in this study not only increases the energy independence of buildings, but also has the advantage of higher renewable energy production compared with fixed solar panels. Additionally, various types of shading structures can be designed depending on the combination of solar panel modules; in particular, moving solar panels have the potential to facilitate ecofriendly designs when applied to the exterior of buildings.

There are two major proposed forms of dark energy: the cosmological constant and the quintessence scalar field. However, the former has the cosmological constant problem and the latter does not have observational evidence to support the theory. In this paper, we propose a dark energy paradigm to solve the cosmological constant problem and to predict lepton masses as evidence. The dark energy paradigm is a unified dark sector that is based on Planck's dimensional analysis, Lambda CDM, energy conservation, and force equilibrium. We find that dark energy can vary from the cosmological constant to the Planck scale. We find that the predicted values of lepton masses based on the dark energy paradigm agree with the observed values to 1% (or within error ranges).

Thermostatically controlled loads have great potential to make a significant contribution to improving energy efficiency in the building sector, which is responsible for 40% of greenhouse gas emissions in the EU. This, in addition to the environmental damage, represents a huge expense in the electricity bill. Therefore, it is very important to train engineers on how to design energy management systems for TCLs. With this goal in mind, it would be very useful to have a simulation-based educational tool (SBET) to understand thermostatically controlled loads, their characteristics and possibilities in energy efficiency. In addition, it would be very useful if this tool could be introduced in engineering curricula to help students to be better trained and enter the labor market with more opportunities. Based on the shortcomings detected, this work develops a SBET specifically designed to teach about TCLs (SBET-TCLs), both about their intrinsic characteristics and their better management. To verify the developed SBET-TCL, it has been tested in a real scenario: A survey was carried out among the students of the subject 'Alternative Energy Sources' of the degrees of Industrial Engineering. The results show that the use of SBET-TCL has very positive effects on the learning process.

Storing apples for up to a year is a well-established practice aimed at providing a continuous, locally-produced fruit supply to consumers and adapting to market trends for optimized profits. Temperature control is the cornerstone of postharvest conservation and apples are typically kept at temperatures from 0 to 3 °C. However, the energy-intensive process of the initial cool down and subsequent temperature maintenance poses significant financial challenges and contributes to the carbon footprint. Higher storage temperatures could reduce cooling-related energy usage but also pose the risk of enhanced ripening and quality loss. This work explores different storage technologies aiming to reduce energy consumption such as 1-methylcyclopropene, ultra-low oxygen and dynamic controlled atmosphere together with raised temperatures. The integration of advanced monitoring and control systems, coupled with data analytics and energy management in apple storage is also discussed. These sustainable strategies can be implemented without cost-intensive construction measures in standard storage facilities. Furthermore, beneficial side effects of higher storage temperatures in terms of a reduced occurrence of storage disorder symptoms and higher maintenance of quality attributes are also discussed for this special issue on sustainable horticultural production systems and supply chains.

This paper proposes a circuit model of Cross-Coupled CMOS AC – DC Charge Pump (XC – CP) operating in subthreshold region. The aim is improving the efficiency to design XC – CPs with variety of specifications, e.g., input and output voltages and AC input frequency. First, it is shown that the output resistance (Ro) of XC – CP is much higher than those of CPs with single diodes (SD – CP) and ultra-low-power diodes (ULPD – CP) as charge transfer switches (CTSs). Second, the reason behind the above feature of XC – CP is identified by a simple model that the gate-to-source voltages of CTS MOSFETs are independent of the output voltage of the CP. Third, high but finite Ro of XC – CP is explainable with a more accurate model that includes the dependence of the saturation current of MOSFETs operating in subthreshold region on the drain-to-source voltage which is a function of the output voltage of CP. The model was in good agreement with measured and simulated results of XC – , SD – and ULPD – CPs fabricated in 250 nm CMOS.

To address global warming, there is a worldwide effort to establish carbon-neutral energy plans. Given the characteristics of renewable energy generation, a diverse 'Energy Mix' consisting of various energy sources such as wind and solar power is crucial. In particular, the wind power is expected to continue expanding globally due to its sustainable nature. Furthermore, the expan-sion of offshore wind farm is making essential and a rapidly growing industry sector to be achieving carbon neutrality with limited land for construction. To facilitate the construction and operation of offshore wind farms, specialized vessels with dynamic positioning (DP) systems are essential such as Wind Turbine Installation Vessels (WTIVs) and Service Operating Vessels (SOVs). The purpose of this study is to predict and analyze the scale and structural changes in the fleet capacity of DP vessel, which is essential for offshore wind power construction as the offshore wind power industry develops using System Dynamics (SD) modeling. Specifically, this study aims to construct a demand forecasting model for DP vessel used in offshore wind farm con-struction based on SD methodology. The study aims to identify influencing factors by analyzing dynamic changes in system configurations over time and establishing causal relationships based on feedback structures. Instead of traditional time series analysis methods, causal relation-ship-based simulations were conducted for quantitative analysis. The results provide insights into the changes in the DP vessel market structure due to the emergence of the new industry and highlight areas that require improvement throughout the industry.

Reducing the construction time for large logistics buildings can result in reduced construction management costs and economic gains from early operation. A large logistic building with a heavy load and long spans was constructed as a precast concrete (PC) structure, which requires the use of a sizable crane to lift heavy PC members. A basic analytical approach is employed to resolve potential errors in the planning of PC member erection and to build a systematic erection plan. Calculation techniques for the trajectory distance, which use the crane location, are applied to select an erection plan that minimizes crane work. A crane trajectory distance calculation algorithm for sustainable PC member erection in large logistic buildings with heavy loads and long spans has been developed. The developed model aids in creating simulation and optimization models to ensure minimal usage of cranes in the future and determining cost, construction time, CO2 emissions, and energy use for each erection plan.

The purpose of this paper is to summarize and share the field experiment results of KEPCO's project consortium to create a TSO-DSO-DERA interaction scheme. The field experiment was conducted based on the prequalification algorithm proposed in the previous research from the same consortium and was designed to verify the validity of the algorithm under realistic grid conditions. In addition, during the course of the field experiment, it was found that points that were missed or not given much importance in the existing prequalification algorithm could affect the completeness of the overall system, and then practical improvements were made to improve it. The demonstration results confirm that the proposed algorithm is effective in real-world grid environments and can help DSOs ensure the reliability of the distribution system while supporting DERA's participation in the wholesale market using the proposed prequalification scheme.

Shallow Geothermal Energy (SGE) exchanges heat with the ground. In continuous long-term operation, the initial temperature field can be disturbed, and subsurface thermal plumes can be developed. In this paper, the thermal impact of a SGE system under Mediterranean climate is handled. Temperature recordings from 104 thermal probes placed in depth along 15 monitoring boreholes are analysed. Those boreholes were drilled 1-2m from thermos-active boreholes of the case study system installed in a university building. The analysis handles one year of SGE system operation. Temperature depth profiles, reaching up to 140 m depth, were registered with a 10-minute time-step resulting in a large amount of data. Ground thermal conductivity was estimated experimentally and semi-empirically allowing to compute the initial undisturbed ground temperature profiles and compare it with the monitored values. Climate data was recorded by the university meteorological station. Globally, the measured and computed data were coherent and a non-negligible impact of the SGE system operation in the first year was observed. The building orientation as well as the nearby departments had significant impacts on shallow ground temperature. Maximum ground temperature changes, ranging from 2 to 3º C as observed in different boreholes indicating that the system is operating efficiently.

Polyhedral Oligomeric Silsesquioxanes (POSS) are one of the smallest silica nano particles. The presence of ordered ladder-like or cage conformation in their structure leads to remarkable thermal stability far greater than that for a linear polysiloxane. Reinforcement with nano particles is one of the recently favored strategy used to enhance the performance of polymers materials. The cyclic silica structure present in POSS ensures excellent thermal and mechanical stability. As a reinforcing filler, POSS can enhance the resistance of polymer matrix against pyrolysis and corrosion. In this paper, amine-terminated POSS with ladder like structure was synthesized by condensation of hydrolyzed aminosilane coupling agent. The ladder-like structure of POSS severely limits the motion of the chain backbone. The absence of phase transition for the synthesized POSS was confirmed by differential scanning calorimetry (DSC). Thermogravimetric analysis (TGA) was utilized to evaluate the thermal stability of POSS. TGA data show that the ladder-like POSS reported here has high char yield of about 75 % in nitrogen atmosphere and 54% in air atmosphere at 800℃. The TGA derivative curves show that the degradation of ladder-like POSS involves multiple stages and that the degradation rate is directly proportional to the heating rate. With the aid of Fourier Transform Infrared Spectroscopy (FT-IR), the cyclic structure of Si-O-Si bonding was determined to be the predominant structure. By analyzing the FTIR spectra of the cured POSS residue obtained at the specified temperatures, the detailed degradation mechanism of POSS was inferred. From the FTIR spectra of the low temperature cured samples, it was shown that the terminal silanol group was eliminated below 400℃. Some intermediate polymeric siloxane structures were observed by means of FT-IR and they eventually transitioned into silica which is the final product of pyrolysis of POSS. The presence of the FTIR transmission peaks at 1000 and 1100 cm-1, due to asymmetrical vertical and horizontal stretching of Si-O-Si, were the key evidence for the inferred ladder-like structure of POSS.

In this paper, we consider the behavior of the local energy flow velocity of the fundamental air – core mode at the core – cladding boundary in two types of hollow – core fibers: hollow – core fibers with a negative curvature of the core boundary and single – capillary fibers with similar geometrical parameters. It is demonstrated that the behavior of both axial and radial components of the local energy velocity of the fundamental air – core mode is completely different for these two types of hollow – core fibers. The negative curvature of the core boundary leads to an alternating behavior of the radial projection of the local energy velocity and a decrease by two orders of magnitude compared to the values of this projection for a single capillary. In our opinion, this behavior of the local energy velocity of the fundamental air – core mode is caused by a periodic set of Poynting vector vortices that appear in the cladding capillary walls.

The decentralized treatment of wastes is studied for an urban scenario considering a high-density population of 2500 inhab./km2. Food and garden waste were assumed to be treated in a co-digestion configuration using several mid-size digesters. In contrast biogas and digestate valorization were carried out in a centralized manner. Electricity and thermal energy were produced from this configuration, accounting for 1.3% of residential electricity demand and 3.2% of thermal demand when using double-turbocharged engines. However, the location of the treatment plants is a factor that may raise social discomfort. Rejection of locating the plant in specific sites close to residential neighbors, nuisance due to possible odor and gaseous emissions, and house market distortions are just a few of a long list of problematic aspects that may threaten the decentralized alternative. These factors are of great relevance and must be given a practical solution if the circular economic model is to be implemented by considering the insertion of waste streams into the production system and generating local energy sources and raw materials.

The requirement for integration of power plants due to the cyclical rise in electrical energy consumption is due to fluctuating load demand with the current grid systems. This integration necessitates effective allocating loads to the power plants for a minimum grid-tied transmission line cost while meeting network constraints. In this paper, we formulate an optimisation problem of minimising the total operational cost of all committed plants transmitted to the grid while meeting network constraints and ensuring economic power dispatch (EPD) and energy management system co-optimization. The developed Particle Swarm Optimization (PSO) method resolve the optimisation problem using piecewise quadratic function to describe the operational cost of the generation units, and the B coefficient approach is employed to estimate the transmission losses. Intelligent adjustments are made to the acceleration coefficients, and a brand-new algorithm is suggested for distributing the initial power values to the generation units. The developed economic power dispatch strategy successfully demonstrated an imperative cost reduction with connected load of 850MW, 1263MW and 2630MW power demand are contrasted with previous PSO application cost values, maximum yearly cost savings of (0.55%, 91.87), (46.55%, 3.78), (73.86%, 89.10) respectively, and significant environmental-benefit. The proposed co-optimisation approach can enhance a significant self-consumption ratio compared to the baseline method.

Brewers’ spent grain (BSG) is an important waste produced in beer companies with a high po-tential to be transformed into commercial by-products. The present paper reports a forecasting technology study with the aid of bibliographic review and patent analysis tools aiming to in-vestigate the maturity of certain technologies, considering the use of BSG on a closed-loop bio-refinery and circular bioeconomy concept integrated into a brewery. To evaluate the possibili-ties of production of high-added value products in Brazil, it was presented an overview of BSG’s scientific, technological, and marketing products and applications. The comparison between numbers of articles versus patents shows that the solutions proposed by research articles are not being transformed into maturated viable technologies. The results suggest that there is a gap between the scientific research in the institutions and their applications in industry, which lead to the destination of the BSG for more economically attractive investments when compared to research in Brazil. Ultimately, from the carried-out analysis, it was possible to propose a brew-ing process connected to the biorefinery system, showing the possibility to the newly arising brewery industries.

This paper presents a novel approach of welding thick steel plates that offers time and energy savings compared with conventional techniques. The combination of gas metal arc welding (GMAW) and hot-wire technology simplifies the joint configuration and enhances the process tolerance. In this study, a square butt joint was prepared with as-cut edges and a thickness of 15 mm. The relationship between the welding current and the deposition rate of solo GMAW showed limitations and low process tolerance. Increasing the welding current led to a larger deposited volume with unnecessary weld penetration. An independent deposition volume due to hot-wire insertion was used to improve process tolerance. This approach provided an additional volume without increasing the welding current and reduced unnecessary penetration. With optimized parameters, full-penetration single-pass welding was achieved. Compared with the formation of a typical single-v butt joint at a similar welding speed of 30 cm/min, the proposed process reduced the minimum arc time and power consumption by approximately 83% and 62%, respectively. Moreover, a single pass at a travel speed of 60 cm/min was achieved with approximately 91% and 81% less arc time and power consumption, respectively. In summary, the combined process simplifies the joint configuration, enables full-penetration single-pass welding, and reduces time and energy requirements.

Semidiurnal tidal currents can exceed 5 ms−1 in Minas Passage, Bay of Fundy, where a tidal energy demonstration area has been designated to generate electricity using marine hydrokinetic turbines. The risk of harmful fish-turbine interaction cannot be dismissed for either migratory or local fish populations. Individuals belonging to several fish populations have been acoustically-tagged and monitored by using acoustic receivers moored within Minas Passage. Detection efficiency ρ is required as the first step to estimate probability of fish-turbine encounter. Moored Innovasea HR2 receivers and high residency (HR) tags were used to obtain detection efficiency ρ as a function of range and current speed, for near-seafloor signal paths within the tidal energy development area. Strong tidal currents moved moorings so HR tag signals, and their reflections from the sea surface, were used to measure ranges from tags to receivers. HR2 self-signals that reflected off the sea surface showed which moorings were displaced to lower and higher levels on the seafloor. Some of the range testing paths had anomalously low ρ which might be attributed to variable bathymetry blocking the line of sight signal path. Clear and blocked signal paths accord with mooring levels. Application of ρ is demonstrated for calculation of abundance, effective detection range, and detection-positive intervals. High residency signals were better detected than pulse position modulation (PPM) signals. Providing the presently obtained ρ applies to tagged fish that swim higher in the water column, there is a reasonable prospect that probability of fish-turbine encounter can be estimated by monitoring fish that carry HR tags.

We calculate energies of shallow donors confined in a rolled-up quantum well in the presence of the electric field by solving numerically the Schrödinger equation in natural curvilinear coordinates. It is found that the curves of density of states (DOS) are very sensitive to the variation of the donor position, the geometry of the spiral and the applied electric field value. Novel results for dependencies of donor’s dipole moment and its polarizability on the electric field strength and its orientation, for different donor positions are presented. Also, we found that anisotropic Stark effect of the first order provides in this structure a dependency of the polarizability on the external electric field in a spike-like shape, giving rise to a sharp variation of the dipole moment.

Tidal stream energy is a renewable energy resource that might be developed to offset carbon emissions. A tidal energy demonstration (TED) area has been designated in Minas Passage, Bay of Fundy, for testing and installing marine hydrokinetic (MHK) turbines. Regulations require quantification of the potential for MHK turbine installations to harm local populations of marine animals. Here we use acoustic telemetry to quantify probability that post smolt Inner Bay of Fundy salmon encounter a turbine installation at the TED area. Previous work has quantified detection efficiency of Innovasea HR acoustic tags as a function of current speed and range from a moored HR2 receiver and also demonstrated that drifters carrying HR tags will be effectively detected when the drifter track crosses the array of HR2 receivers in Minas Passage. Salmon smolts were tagged and released in Gaspereau and Stewiacke Rivers, Nova Scotia, in order that the HR2 receiver array could monitor seaward migration of the post smolts through Minas Passage and particularly through the TED area. Presently we demonstrate methods by which tag signals detected by the HR2 array can be used to estimate the expected number of times that a post smolt would encounter a single near-surface MHK turbine installation during its seaward migration.

In this paper, a systematic literature review is presented, through a survey in the main digital databases, about modelling methods for Short-Term Load Forecasting (STLF) for hourly electricity demand for residential electricity and to realize the performance evolution and impact of the Artificial Intelligent (AI) in STLF. With these specific objectives, it was developed a conceptual framework on the subject, a systematic review of the literature based on scientific publications with high impact and a bibliometric study directed to the scientific production of AI and STLF. The review of research articles over a 10-year period, which takes place between 2012-2022, uses the Preferred Reporting Items for Systematic and Meta-Analyses (PRISMA) method. This research resulted in more than 300 articles, available in 4 (four) databases: Web of Science, IEEE Xplore, Scopus and Science Direct. The research was organized around 3 (three) central themes, which were defined through keywords: STLF, Electricity, Residential and their corresponding synonyms. 334 research articles were analyzed and identified the year of publication, journal, author, geography by continent and country and the area of application. Of the 334 documents found in the initial research and after applying the inclusion/exclusion criteria, which allowed delimiting the subject addressed in the topics of interest for analysis, 37 (thirty-seven) documents are in English (25 are journal articles and 12 are conference papers). The results point to a diversity of modelling techniques and associated algorithms. The corresponding performance is measured with different metrics and, therefore, cannot be compared directly. Hence, it should be desirable to have a unified data set together with a set of benchmarks with well-defined metrics for a clear comparison of all the modelling techniques and the corresponding algorithms.

Spherically symmetric solution in 4D Einstein--Gauss--Bonnet gravity coupled to modified logarithmic nonlinear electrodynamics (ModLogNED) is found. This solution at infinity possesses the charged black hole Reissner--Nordstr\"{o}m behavior. We study the black hole thermodynamics, entropy, shadow, energy emission rate and quasinormal modes. It was shown that black holes can possess the phase transitions and at some range of event horizon radii black holes are stable. The entropy has the logarithmic correction to the area law. The shadow radii were calculated for variety of parameters. We found that there is a peak of the black hole energy emission rate. The real and imaginary parts of the quasinormal modes frequencies were calculated. The energy conditions of ModLogNED are investigated.

Omicron BA.2.75 may become the next globally dominant strain of COVID-19 in 2022. BA.2.75 sub-variant has acquired more mutations (9) in spike protein and other genes of SARS-CoV-2 than any other variant. Thus, its chemical composition and thermodynamic properties have changed comparing to earlier variants. In this paper Gibbs energy of binding and antigen-receptor binding rate is reported for the BA.2.75 variant. Gibbs energy of binding (driving force of binding) of Omicron BA.2.75 variant is more negative than that of the competing variants BA.2 and BA.5.

This paper presents a novel theoretical and computational methodology for the generation of an onset turbulent field with prescribed properties in the numerical simulation of an arbitrary viscous flow. The methodology is based on the definition of a suitable distribution of volume force terms in the right–hand side of the Navier–Stokes equations. The distribution is represented by harmonic functions that are randomly variable in time and space. The intensity of the distribution is controlled by a simple PID strategy in order to obtain that the generated turbulent flow matches a prescribed turbulence intensity. A further condition is that a homogeneous isotropic flow is es- tablished downstream of the region where volume force terms are imposed. Although it is general, the proposed methodology is primarily intended for the computational modelling of hydrokinetic turbines in turbulent flows representative of tidal or riverine installations. A first numerical applica- tion is presented by considering the injection of homogeneous and isotropic turbulence with 16% intensity into a uniform unbounded flow. The analysis of statistical properties as auto-correlation, power spectral density, probability density functions, demonstrates that the generated flow tends to achieve satisfactory levels of stationarity and isotropy, whereas the simple control strategy used determines overestimated turbulent intensity levels.

Although the fusion energy sector is at a nascent stage, the private fusion energy market has grown. There are currently 38 private fusion energy companies around the world aiming to commercialise fusion energy in early 2030s and 2040s. Given the capability of fusion energy in transforming today’s energy paradigm and the global character of the market, it is important to analyse how these companies are interacting with international human rights standards. Therefore, this work investigates the involvement of the private fusion energy sector with two voluntary international initiatives in particular: the UN Global Compact and the UN Guiding Principles on Business and Human Rights (UNGP). This study attempts to answer two research questions: (i) Are private fusion energy companies participating in the UN Global Compact? (ii) How are private fusion energy companies publicly implementing the UNGP? Content analysis of secondary data collected from the UN Global Compact, Fusion Industry Association, ITER and companies’ official website as well as published reports is adopted. In summary, this work finds that private fusion energy companies are neither participants nor signatories of the UN Global Compact. Their observance of the UNGP is also very poor. This study contributes to the field by highlighting this gap which the private fusion energy companies need to consider and take measures in order to create a salutary human rights sector.

Scale invariance is expected in empty Universe models, while the presence of matter tends to suppress it. As shown recently, scale invariance is certainly absent in cosmological models with densities equal to or above the critical value ρ_c = 3(H₀)²/(8πG). For models with densities below ρc, the possibility of limited effects remains open. If present, scale invariance would be a global cosmological property. Some traces could be observable locally. For the Earth-Moon two-body system, the predicted additional lunar recession would be increased by 0.92 cm/yr, while the tidal interaction would also be slightly increased. The Earth-Moon distance is the most systematically measured distance in the Solar System, thanks to the Lunar Laser Ranging (LLR) experiment active since 1970. The observed lunar recession from LLR amounts to 3.83 (±0.009) cm/yr; implying a tidal change of the length-of-the-day (LOD) by 2.395 ms/cy. However, the observed change of the LOD since the Babylonian Antiquity is only 1.78 ms/cy, a result supported by paleontological data, and implying a lunar recession of 2.85 cm/yr. The significant difference of (3.83-2.85) cm/yr = 0.98 cm/yr, already pointed out by several authors over the last two decades, corresponds well to the predictions of the scale-invariant theory, which is also supported by several other astrophysical tests.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

Abstract: The increased penetration of renewables in distribution power systems has motivated researchers to take significant interest in local energy transactions. The major goal of Local Energy Markets (LEM) is to promote the participation of small consumers in energy transactions and providing an opportunity for transactive energy systems. Such energy transactions in LEM are considered as a bi-level optimization problem in which all agents at upper and lower levels try to maximize their profits. But typical bi-level problem is very complex as it is inherently nonlinear, discontinued and strongly NP-hard. So, this article proposes the application of hybridized Cross Entropy Covariance Matrix Adaptation Evolution Strategy (CE-CMAES) to tackle such a complex bi-level problem of LEM. The proposed CE-CMAES secured the 1st rank in Testbed-2 entitled, “Bi-level optimization of end-users’ bidding strategies in local energy markets (LM)” at international competitions on Smart Grid Problems, held at GECCO 2020 and WCCI 2020. CE method is used for global exploration of search space and CMAES is used for local exploitation as its adaptive step-size mechanism prevents its premature convergence. A practical distribution system with renewable energy penetration is considered for simulation. The comparative analysis shows that the overall cost, mean fitness and Ranking Index (R.I) obtained from CE-CMAES are superior to those obtained from the state-of-the-art participated algorithms. Wilcoxon Signed Rank Statistical test also proves that CE-CMAES is statistically different from the tested algorithms.

Extensive in-situ resource utilisation (ISRU) will be essential to enable long-duration stays on Luna and Mars and reduce reliance on resupply from Earth. Early development of ISRU technologies has focused on standalone capabilities for specific targets related to life support and ascent propellant. An unexplored opportunity remains for greatly expanding the scope of materials that can be supplied by ISRU, and for integrating various technology platforms into a larger system. Recent advances in power-to-X technology aimed at decarbonising the global economy have made it possible to drive key chemical processes using electricity with small-scale, modular reactor. This paper proposes a vision for an integrated system of ISRU processes based on power-to-X technology to produce oxygen, hydrogen, water, methane, polymers, metal alloys, and synthetic fertilisers, using Martian regolith, atmosphere, and ice. A ‘building block’ strategy is adopted to convert raw materials into versatile intermediaries, which can then be combined to form essential products. A wider range of raw materials are available on Mars compared to Luna, suggesting greater opportunity for ISRU deployment to compensate for the greater time and cost requirements for a Mars resupply mission.

As a consequence of the increasing share of renewable energies and sector coupling technologies, new approaches are needed for the study, planning, and control of modern energy systems. Such new structures may add extra stress to the electric grid, as is the case with heat pumps and electrical vehicles. Therefore, the optimal performance of the system must be estimated considering the constraints imposed by the different sectors. In this research, a dispatch optimization method with an iterative grid constraint generation, decoupled from the linear unit commitment problem, is employed. From the considered scenarios, it was found that in a typical German neighborhood with 150 households, PV penetration of ∼5kWp per household can lead to curtailment of ∼60MWh per year due to line loading. Furthermore, the proposed method eliminates grid violations due to the addition of new sectors reducing the curtailment up to 60%. With the optimization of the heat pump operation, an increase of 7% of the self-consumption was achieved with similar results for the combination of battery systems and electrical vehicles. In conclusion, a safer and optimal operation of a complex energy system is fulfilled. Safer control strategies and more accurate plant sizing could be derived from this work.

Doubly Fed Induction Generator (DFIG) has a stator winding directly coupled with grid. Whereas, rotor winding is connected via a fault-prone back to back power converters. DFIG is known to be vulnerable to the grid faults. In early times, when a fault occurred, these generators were required to disconnect from the grid to secure the generator and power converters. However, due to the increased penetration of wind turbines into the power system, grid operators demanded that the wind turbines remain connected to the grid, as disconnecting them would further disrupt the grid. When a fault at the grid terminal occur, a high stator current is induced which further result in high rotor current. This current will trigger the DC-link voltage to rise. This high currents and DC-link voltage will cause harm to the converters. Thus, in this paper work, the crowbar protection system is employed for protecting the converters against excess energy. Furthermore, the analysis of DFIG is rendered by integrating the crowbar protection with the Battery Energy Storage System (BESS) for a much effective outcome in enhancing machine to drive the fault. MATLAB-Simulink software is used for modeling and simulation. All system parameters are obtained from ADAMA-II Wind Farm.

The corrugated board packaging industry is increasingly using advanced numerical tools to design and estimate the load capacity of its products. That is why numerical analyzes are becoming a common standard in this branch of manufacturing. Such trend causes either the use of advanced computational models that take into account the full 3D geometry of the flat and wavy layers of corrugated board, or the use of homogenization techniques to simplify the numerical model. The article presents theoretical considerations that extend the numerical homogenization technique already presented in our previous work. The proposed here homogenization procedure also takes into account the creasing and / or perforation of corrugated board, i.e. processes that undoubtedly weaken the stiffness and strength of the corrugated board locally. However, it is not always easy to estimate how exactly these processes affect the bending or torsional stiffness. What is known for sure is that the degradation of stiffness depends, among other things, on the type of cut, its shape, the depth of creasing, as well as their position or direction in relation to the corrugation direction. The method proposed here can be successfully applied to model smeared degradation in a finite element or to define degraded interface stiffnesses on a crease line or a perforation line.

At present, the world is at the peak of production of traditional fossil fuels. Much of the resources that humanity has been consuming (oil, coal and natural gas) are coming to an end. The human being faces a future that must necessarily go through a paradigm shift, which includes a progressive movement towards increasingly less polluting and energetically viable resources. In this sense, nanotechnology has a transcendental role in this change. For decades, new materials capable of being used in energy processes have been synthesized that undoubtedly will be the cornerstone of the future development of the planet. In this review, we report on the current progress in the synthesis and use of one-dimensional (1D) nanostructured materials (specifically nanowires, nanofibers, nanotubes and nanorods), with compositions based on oxides, nitrides, or metals, for applications related to energy. Due to its extraordinary surface-volume relationship, tunable thermal and transport properties, and its high surface area, these 1D nanostructures have become fundamental elements for the development of energy processes. The most relevant 1D nanomaterials, their different synthesis procedures, and useful methods for assembling 1D nanostructures in functional devices will be presented. Applications in relevant topics such as optoelectronic and photochemical devices, hydrogen production or energy storage, among others, will be discussed. The present review concludes with a forecast on the directions towards which future research could be directed on this class of nanostructured materials.

Spatiotemporal dynamics of the atmospheric kinetic energy and its components caused by the ordered and turbulent motions of air masses are estimated from minisodar measurements of three velocity vector components and their variances within the lowest 5–200 m layer of the atmosphere, with a particular emphasis on the turbulent kinetic energy. The layered structure of the total atmospheric kinetic energy has been established. From the diurnal hourly dynamics of the altitude profiles of the turbulent kinetic energy (TKE) retrieved from minisodar data, four layers are established by the character of the altitude TKE dependence, namely, the near-ground layer, the surface layer, the layer with a linear TKE increase, and the transitive layer above. In the first layer, the most significant changes of the ТКЕ were observed in the evening hours. In the second layer, no significant changes in the TKE values were observed. A linear increase in the TKE values with altitude was observed in the third layer. In the fourth layer, the TKE slightly increased with altitude and exhibited variations during the entire observation period. The altitudes of the upper boundaries of these layers depended on the time of day. The MKE values were much less than the corresponding TKE values, they did not exceed 50 m²/s². From two to four MKE layers were distinguished based on the character of its altitude dependence. The two-layer structures were observed in the evening and at night (under conditions of the stable atmospheric boundary layer). In the morning and daytime, the four-layer MKE structures with intermediate layers of linear increase and subsequent decrease in the MKE values were observed. Our estimates demonstrated that the ТКЕ contribution to the total atmospheric kinetic energy considerably (by a factor of 2.5–3) exceeded the corresponding МКЕ contribution.

Not only does this paper present a novel type-2 fuzzy system for identification and behavior prognostication of an experimental solar cell set and a wind turbine, but also it brings forward an exquisite technique to acquire an optimal number of membership functions and the corresponding rules. It proposes a seven-layered NCPRT2FS. For fuzzification in the first two layers, Gaussian type-2 fuzzy membership functions with uncertainty in the mean, are exploited. The third layer comprises rule definition and the forth one embeds fulfillment of type reduction. The three last remained layers are the ones in which resultant left–right firing points, two end-points and output all get assessed correspondingly. It should not be neglected off the nutshell that recurrent feedback at the fifth layer exerts delayed outputs ameliorating efficiency of the suggested NCPRT2FS. Later in the paper, a modern structural learning, established on type-2 fuzzy clustering, is held forth. An adaptively rated learning back-propagation algorithm is extended to adjust the parameters ensuring the convergence as well. Eventually, solar cell photo-voltaic and wind turbine are deemed as case studies. The experimental data are exploited and the consequent yields emerge so persuasive.