Damaged connective tissues between the bone and tendons or ligaments are common among adults regardless of activity level. Achilles tendinosis is one of the most common tissue defects and enthesopathies. The patient in this study is a 54-year-old female with chronic Achilles tendinosis from chronic enthesopathy at the Achilles tendon insertion with a retrocalcaneal exostosis for three years who has failed standard-of-care practices for over two years. The patient received extracorporeal pulsed-activated therapy (EPAT) before applying 2ml of CryoText, a Wharton’s jelly tissue allograft. The patient then received class IV laser therapy treatments twice weekly for three weeks. The patient started with a 10/10 VAS at the initial visit. At five weeks post-application, the patient’s score had improved by 80% at 2/10 VAS. By week 13, the patient rated her pain as 0/10 VAS. The improvement in patient-reported pain and functionality reported in this study after the application of Wharton’s Jelly, EPAT, and class IV laser therapy warrants future research studying the safety and efficacy of these patient care modalities together.

Speckle Plethysmography (SPG) and Photoplethysmography (PPG) are different biophotonics technologies that allow for measurement of hemodynamics. As the difference between SPG and PPG under low perfusion conditions is not fully understood, a Cold Pressor Test (CPT) was used to modulate blood pressure and peripheral circulation. A custom-built setup simultaneously derived SPG and PPG from the same video streams at two wavelengths (639 nm and 850 nm). SPG and PPG were measured at right index finger location before and during CPT using finger Arterial Pressure (fiAP) as reference. The effect of CPT on Alternating Component amplitude (AC) and Signal-to-Noise-Ratio (SNR) of dual-wavelength SPG and PPG signals was analysed across participants. Furthermore, waveform differences between SPG, PPG, and fiAP based on frequency harmonic ratios, were analysed for each subject (n=10). Both PPG and SPG at 850 nm show a significant reduction during CPT for both AC and SNR. However, SPG showed significantly higher and more stable SNR than PPG in both study phases. Harmonic ratios were found substantially higher in SPG than PPG. Therefore, in low perfusion conditions, SPG seems to offer a more robust pulse wave monitoring with higher harmonic ratios than PPG.

The pulse duration in short-pulse schemes for Self-Amplified Spontaneous Emission Free Electron Lasers (SASE FELs) is limited by the FEL coherence time. A recently proposed concept allows to overcome the coherence time barrier and to get much shorter pulses. When the lasing part of an electron bunch is much shorter than the coherence time, one can suppress the radiation in the long main undulator while preserving microbunching within that short lasing slice. Then a short radiation pulse is produced in a relatively short radiator. A possible suppression method, an excessive reverse undulator taper, is discussed and illustrated numerically in this paper. We also performed first experimental tests of this method at the soft X-ray FEL user facility FLASH. The measured pulse duration approaches 1 fs (FWHM) at the wavelength of 5 nm.

Abstract: The calibrator is one of the most important factors in the calibration of various laser 3D scanning instruments. The requirements for diffuse reflection surface are specially emphasized in many national standards. In this study, the spherical calibrator and plane calibrator compara-tive measurement experiments were carried out. The black ceramic standard sphere, white ce-ramic standard sphere, metal standard sphere, metal standard plane and white ceramic standard plane were used to test the laser 3D scanner. In the spherical calibrators comparative measure-ment experiments, the results indicated that the RMS of the white ceramic spherical calibrator with reflectance about 60% is 10 times that of the metal spherical calibrator with the reflectance of about 15%, and the RMS of the black ceramic spherical calibrator with reflectance of about 11% is of the same order as the metal spherical calibrator. In the plane calibrators comparative measurement experiments, the RMS of flatness measurement is 0.077 mm for metal plane cali-brator with reflectance of 15%, and 2.915 mm for ceramic plane calibrator with reflectance of 60%. The results show that when the optimal measurement distance and incident angle are selected, the reflectance of the calibrator has a great effect on the measurement results, regardless of the outlines or profiles. Based on the experiments, it is recommended to use the spherical calibrator or the standard plane with reflectance of around 18% as the standard, which can obtain the rea-sonable results. In addition, it is necessary to clearly provide the material category and surface reflectance information of the standard when calibrating the scanner according to the measure-ment standard.

In the past years, our knowledge of coastal environments has been enriched by remotely sensed data. However, to successfully extract information from a combination of different sensors systems, it should be understood how these interact with the common coastal environment. In this research we co-analyze two sensor systems: Terrestrial Laser Scanning (TLS) and satellite based Synthetic Aperture Radar (SAR). TLS shows large potential for examining coastal processes thanks to the possibility to retrieve repeated, accurate and dense topographic information in a rapid and non-invasive manner. However, TLS presents some limits due to its high economic costs and limited field of view. SAR systems are among the most used active remote sensor system for Earth Observation. Despite their relatively low resolution, SAR systems provide the ability to monitor and map coastal areas with complete, repeated and frequent coverage, penetrating through clouds and providing all weather monitoring. Moreover, Sentinel-1 SAR images are freely available. The availability of a permanently installed TLS system (PLS, Permanent Laser Scanner) allows us, to extensively compare Sentinel-1 SAR data and topographic laser scans during different conditions on a sandy beach. PLS data are compared with simultaneous Sentinel-1 SAR images in order to investigate the combined use of PLS and SAR in coastal environments. The purpose of this comparison is the investigation of a possible relation between PLS and SAR data: knowing their relation, SAR dataset could be correlated to beaches characteristics. Meteorological and surface roughness have also been taken into consideration in the evaluation of the correlation between PLS and SAR data. The permanently installed laser scanner for the present study is located in Noordwijk (the Netherlands). A generally positive but low correlation exists between the two variables. When considering weather phenomena, their correlation increases and shows a dependence on wind directions and speed. The correlation with the surface roughness, evaluated in terms of root-mean squared height, also depends on specific wind speed and directions.

We utilized laser irradiation as a potential technique in tuning the electrical performance of NiOx/SiO2 thin film transistors (TFTs). By optimizing the laser fluence and the number of laser pulses, the TFT performance is evaluated in terms of mobility, threshold voltage, on/off current ratio and subthreshold swing, all of which were derived from the transfer and output characteristics. The 500 laser pulses irradiated NiOx/SiO2 TFT exhibited an enhanced mobility of 3 cm2/V-s from a value of 1.25 cm2/V-s for as-deposited NiOx/SiO2 TFT. The laser-irradiated NiOx material likely has a significant concentration of defect gap states, which could also be involved in light absorption processes. Second, and more importantly, the excess energy that the photogenerated charge carriers possess (due to the significant difference between the photon energy and the bandgap of NiOx), combined with the very high light intensity, would result in complex thermal and photo thermal changes thus resulting in an enhanced electrical performance of p-type NiOx/SiO2 TFT structure.

Extracorporeal shock wave therapy (ESWT) is a well investigated and widely used treatment modality for a number of musculoskeletal disorders. A limitation of ESWT is its potential painfulness at higher, clinically relevant energy flux density (EFD), which may limit its applicability and, thus, effectiveness. Various studies in the literature demonstrated that neither application of a higher number of extracorporeal shock waves with lower EFD nor use of local anesthesia may solve this problem. Based on the results of several other studies in the literature it is hypothesized here that in patients suffering from musculoskeletal disorders that can be treated with ESWT, pretreatment with a pulsed, high power laser with a wavelength of 904 or 905 nanometers (hereafter: "laser pretreatment") does not only allow to apply higher EFDs in subsequent ESWT but actually results in faster and/or better treatment outcome than ESWT without laser pretreatment. Accordingly, it is hypothesized here that combining ESWT with laser pretreatment leads to synergistic effects and, thus, is superior to either treatment modality alone. Confirming this hypothesis in preclinical and clinical research may raise significance and increase the use of ESWT in physical and rehabilitation medicine, with immediate benefit for patients.

The inherent trace quantity of primary fatty acid amides found in biological systems presents challenges for analytical analysis and quantitation, requiring a highly sensitive detection system. The use of microfluidics provides a green sample preparation and analysis technique through small-volume fluidic flow through micron-sized channels embedded in a PDMS device. Microfluidics provides the potential of having a micro total analysis system where chromatographic separation, fluorescent tagging reactions, and detection are accomplished with no added sample handling. This study describes the development and optimization of a microfluidic-laser indued fluorescence (LIF) analysis and detection system that can be used for the detection of ultra-trace levels of fluorescently tagged primary fatty acid amines. A PDMS microfluidic device was designed and fabricated to incorporate droplet-based flow. Droplet microfluidics have enabled on-chip fluorescent tagging reactions to be performed quickly and efficiently, with no additional sample handling. An optimized LIF optical detection system provided fluorescently tagged primary fatty acid amine detection sub-fmol (436 amol) LODs. The use of this LIF detection provides unparalleled sensitivity, with detection limits several orders of magnitude lower than currently employed LC-MS techniques and might be easily adapted for use as a complementary quantification platform for parallel MS-based -omics studies.

We propose a new approach of extending the laser filament plasma channel. By adding a circular aperture quartz plate before the focusing lens, the extension of the plasma channel is doubled. The effects of different diameters, thicknesses of the circular aperture quartz plate and different pulse energies on the length of the plasma channel were investigated. The experimental results show that the thickness of the quartz plate and the depth of the hole have little effects on the plasma channel of the filament, and the diameter of the hole in the center of the quartz plate has a significant effect on the length of the optical filament. The moving-focus model is used to explain the extension of the optical filament.

Nowadays, the uses of laser and optics in the medical areas are extremely vivid, especially low-level laser therapy. The light with the wavelength of 633 nm to 1200 nm could penetrate and propagate deep in biological tissue. To develop the low-level laser therapy device, optimizing light delivery is critical to accurately stimulate the biological effects inside the biological tissue. Nevertheless, each form of the tissues at each zone on the body had various refractive optic, absorption, scattering, and anisotropy coefficients. This paper describes the simulation results of low-level laser propagation from skin surface at the lower spine, the knee, the femur and the prostate gland with four wavelengths (633 nm, 780 nm, 850 nm, and 940 nm) by the Monte Carlo method. These simulation results are the base for developing the low-level laser therapy device, that could be used in clinical for treating the fracture, knee osteoarthritis, spinal degeneration, and benign prostatic hypertrophy.

A novel mathematical model is developed to calculate the temperature distribution on the surface and bulk of a steel plate under the laser hardening process. The model starts with the basic heat equation then it is developed into a volumetric form and is connected to the various solid existing phases. The proposed model is based on three influencing parameters of the laser hardening process which are the velocity of the laser spot and irradiation time. The results are compared with the available experimental data reported in the literature. The volumetric model provides an assessment of temperature distribution in both the vertical and horizontal axis. Laser irradiation at sufficiently high fluence can be used to create a solid-state phase change on the surface. Primary calculations show that the temperature profile has a Gaussian distribution in horizontal x and y-axis and presents an exponentially decreasing in the horizontal and vertical depth directions.

This work examines atomic and molecular signatures in laser-induced plasma in standard ambient temperature and pressure environments, including background contributions to the spectra that depend on the laser pulse-width. Investigations include solids, gases, and nano-particles. Abel inversions of measured line-of-sight data reveal insight into the radial plasma distribution. For nominal 6 nanosecond laser pulses and for pulse-energies in the range of 100 to 800 mJ, expansion dynamics and turbulence due to shock phenomena are elucidated to address local equilibrium details that are frequently assumed in spatially averaged emission spectroscopy. Chemical equilibrium computations reveal temperature dependence of selected plasma species. Specific interests include atomic hydrogen (H) and cyanide (CN). Atomic hydrogen spectra indicate axisymmetric shell structures and isentropic expansion of the plasma kernel over and above the usual shockwave. The recombination radiation of CN emanates within the first 100 nanoseconds for laser-induced breakdown in a 1:1 CO2:N2 gas mixture when using nanosecond laser pulses to create the micro-plasma. The micro-plasma is generated using 1064 nm, 150 mJ, 6 ns Q-switched Nd:YAG laser radiation. Measurements of the optical emission spectra utilize a 0.64 m Czerny-Turner type spectrometer and an intensified charge-coupled device.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (h_f) and the maximum depth (h_max) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s⁻¹ and 0.1 s⁻¹. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

The resonance spectra of neutral silver indicate self-absorption for the studied Ag I lines at the wavelengths of 327.9 nm and 338.2 nm. The center dip is associated with self-reversal due to self-absorption in the plasma. The Q-switched radiation of 355 nm, 532 nm, or 1064 nm from a Nd:YAG laser device generates the plasma at the surface of silver nano-material targets, with experiments conducted in standard ambient temperature and pressure laboratory air. Procedures for recovery of the spectral line shapes confirm that over and above the effects of self-reversal, line shape distortion are important in the analysis. The work discusses parameters describing self-absorption when using fluence levels of 2 to 33 J/cm² to generate the plasma. Furthermore, subsidiary calibration efforts that utilize the hydrogen alpha line of the Balmer series show that the Ag I lines at 827.35 nm and 768.7 nm are optically thin.

Outer particles collision with certain dynamic object is not a pure impact wear behavior; it is typically accompanied by sliding wear phenomena. This study aimed investigating the impact-sliding wear performance of three different TC17 titanium alloys. One was untreated, and the other two were subjected to laser shock peening (LSP) by 5 and 7 J pulse energy, respectively. Wear test was performed on a novel impact-sliding wear testing rig, which can realize multiple impact-sliding motions by changing motion parameters in x and z directions. Present results showed that wear resistance of both treated samples improved compared with the untreated alloy. Given the increase in wear cycles, increment in wear rate of the untreated sample was constantly higher than those of treated samples. All results can be attributed to the increase in surface hardness of the material and residual compressive stress, which was also introduced after LSP.

The study proposes laser shock peening without a coating of high strength ultrafine bainitic steel to mitigating the fatigue failures for automotive and structural engineering applications. Laser pulse density of 2500 pulses/cm2 (75% overlapping) was optimised based on the induced residual stresses for employing the wide range of characterisations. The roughness and topographic results showed that surface roughening was controlled by tuning the laser pulse density. The High-Resolution X-ray Diffraction analysis confirmed the lattice misorientation resulting peak shift and the trend towards martensite phase transformations. The electron microscopic micro/nanostructure analyses revealed the grain refinement features such as nano-twins, micro shear bands and shear cells. The work hardening depth and nanomechanical properties were significantly enhanced. A fully reversed (R= -1) high-cycle fatigue tests extended the lifespan by an average of fifteen times than the untreated. Also, it has potential to repair the structural components effectively.

Laser scanning systems make use of Light Detection and Ranging (LiDAR) technology to acquire accurately georeferenced sets of dense 3D point cloud data. The information acquired using these systems produces better knowledge about the terrain objects which are inherently 3D in nature. The LiDAR data acquired from mobile, airborne or terrestrial platforms provides several benefit over conventional sources of data acquisition in terms of accuracy, resolution and attributes. However, the large volume and scale of LiDAR data have inhibited the development of automated feature extraction algorithms due to the extensive computational cost involved in it. Moreover, the heterogeneously distributed point cloud, which represents objects with varying size, point density, holes and complicated structures pose a great challenge for data processing. Currently, geospatial database systems do not provide a robust solution for efficient storage and accessibility of raw data in a way that data processing could be applied based on optimal spatial extent. In this paper, we present Global LiDAR and Imagery Mobile Processing Spatial Environment (GLIMPSE) system that provides a framework for storage, management and integration of 3D LiDAR data acquired from multiple platforms. The system facilitates an efficient accessibility to the raw dataset, which is hierarchically represented in a geographically meaningful way. We utilise the GLIMPSE system to automatically extract road median from Airborne Laser Scanning (ALS) point cloud. In the first part of this paper, we detail an approach to efficiently retrieve the point cloud data from the GLIMPSE system for a particular geographic area based on user requirements. In the second part, we present an algorithm to automatically extract road median from the retrieved LiDAR data. The developed road median extraction algorithm utilises the LiDAR elevation and intensity attributes to distinguish the median from the road surface. We successfully tested our algorithms on two road sections consisting of distinct road median types based on concrete and grass-hedge barriers. The use of GLIMPSE improved the efficiency of the road median extraction in terms of fast accessibility to ALS point cloud data for the required road sections. The developed system and its associated algorithms provide a comprehensive solution to the user's requirement for an efficient storage, integration, retrieval and processing of large volumes of LiDAR point cloud data. These findings and knowledge contribute to a more rapid, cost-effective and comprehensive approach to surveying road networks.

Stess in laser cladding coating is an important factor affecting the safe operation of remanufacturing components. Ultrasonic testing has become a hot direction in nondestructive evaluation of stress, because it has the advantages of safety, non-destructive and on-line detection. This paper provides a review of ultrasonic testing for stress in remanufacturing laser cladding coating. It summarizes the recent research outcomes on ultrasonic testing for stress, analyzes mechanism of ultrasonic testing for stress. Remanufacturing laser cladding coating shows typical anisotropic behaviors, the ultrasonic testing signal in laser cladding coating is influenced by many complex factors, such as microstructure, defect, temperature and surface roughness, etc. At present, ultrasonic testing for stress in laser cladding coating can only be done roughly. The paper discusses active mechanism of micro / macro factors to the reliability of stress measurement and the impact of stress measurement to the quality and safety of remanufacturing components. Base on the discussion, the paper proposes strategies for acquisition of nondestructive, rapid and accurate measurement of stress in remanufacturing laser cladding coating.

MAPLE (matrix assisted pulsed laser evaporation) depositions of Candida Rugosa lipase were carried out from ice matrices whose composition is optimized in order to minimize conformational damage of the protein, which strongly influences its catalytic activity. To induce lid opening and to protect lipase during the MAPLE process, pentane and m-DOPA amino acid were added to the liquid matrix giving a target formed by a frozen water-lipase-pentane microemulsion. FTIR and AFM were used to investigate the structure of MAPLE deposited lipase films. The ability of MAPLE films to promote transesterification was determined by thin layer chromatography. It was shown that m-DOPA has influence on the aggregation but not on the unfolding of lipase induced by MAPLE, while the microemulsion formed by the addition of pentane to the target composition is effective in protecting lipase during the MAPLE process. MAPLE deposited lipases showed a modified specificity.

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI–TOF MS) is a commonly used technique for analyzing large biomolecules. However, the utilization of organic matrices limits the small-molecule analysis because of the interferences in the low-mass region and reproducibility issues. To overcome these limitations, a surface-assisted laser desorption/ionization (SALDI), which utilizes nanostructured metallic surfaces, has been developed. Herein, a novel approach for SALDI–MS was proposed using nanoengineered gold shell with nanogaps on the silica core (SiO2@Au NGS), which is an emerging material due to its excellent heat-generating capabilities. The gold shell thickness was controlled by adjusting the concentration of gold precursor for the growth of gold nanoparticles. SALDI-MS measurements were performed on a layer formed by drop-casting a mixture of SiO2@Au NGS and analytes. At the optimized process, the gold shell thickness was observed to be 17.2 nm, which showed the highest absorbance. The ion desorption efficiency was confirmed with a survival yield upon fragmentation. Based on the enhanced SALDI capability, SiO2@Au NGS was utilized to detect various small molecules including amino acids, sugars, and flavonoids. The limits of detection, reproducibility, and salt tolerance of SiO2@Au NGS demonstrate its potential as an effective and reliable SALDI material for small-molecule analyses.

Ultrafast laser 3D lithography based on non-linear light-matter interactions, widely known as multi-photon lithography (MPL), offers unrivaled precision rapid prototyping and flexible additive manufacturing options. 3D printing equipment based on MPL are already commercially available, yet there is still no comprehensive understanding of factors determining spatial resolution, accuracy, fabrication throughput, repeatability, and standardized metrology methods for the accurate characterization of the produced 3D objects and their functionalities. The photoexcitation mechanisms, spatial-control or photo-modified volumes, and the variety of processable materials are topics actively investigated. The complexity of the research field is underlined by limited understanding and fragmented knowledge of light-excitation and material response. Research to date has only provided case-specific findings on photoexcitation, chemical modification, and material characterization of the experimental data. In this review, we aim to provide a consistent and comprehensive summary of the existing literature on photopolymerization mechanisms under highly confined spatial and temporal conditions, where, besides the excitation and cross-linking, parameters such as diffusion, temperature accumulation, and the finite amount of monomer molecules start to become of critical importance. Key parameters such as, photoexcitation, polymerization kinetics, and the properties of the additively manufactured materials at the nanoscale in 3D are examined, whereas, the perspectives for future research and as well as emerging applications are outlined.

This article discusses laser-induced laboratory-air plasma measurements and analysis of hydroxyl (OH) ultraviolet spectra. New experiments with Q-switched laser pulses illustrate occurrence of molecular recombination spectra for time delays of the order of several dozen of microseconds after plasma initiation. The computation of the emission spectra utilizes line strength data that are communicated as a supplementary file. Applications of detailed OH computations include laser-induced plasma and combustion analyses, to name but two applications.

This work aims to explore the impact of side loads, drill-pipe tool-joint (DP-TJ) speed (RPM), and mud type on the austenitic stainless steel SM2535-110 casing wear characteristics. Actual field drill pipe tool joints, casings, and drilling muds are used in this study. The results of the study show that under both types of lubrication, the wear volume increased with radial load and DP-TJ speed. SM2535-110 casing specimens tested under oil-based mud (OBM) lubrication had higher casing wear volumes than those obtained under water-based mud (WBM) lubrication. This unexpected behavior is mainly due to the increase in the surface hardness of the casing specimens tested under WBM. The results also show that the specific wear factor (K) values of specimens tested under WBM are in general 2 to 4 times higher than those obtained under OBM. While K values under WBM increase with both the side load and RPM, those under OBM show a sharp decrease with RPM. This behavior under OBM is due to this lubricant’s higher viscosity and the change of lubrication regime from thin film to thick film lubrication at higher RPM. Scanning electron microscopy (SEM) and the digital microscopic imaging (DMI) of SM235-110 casing specimens show that an aggressive combination of adhesive, abrasive, and plastic deformation was observed under WBM, while the dominant wear mechanism under OBM is abrasive wear.

Financial markets require a great deal of decision making from the investors and market makers. One metric that can help ease the process of decision making is investment risk which can be measured in two parts; systematic risk and idiosyncratic risk. Clear understanding of the volatilities in each risk component can be a powerful signal in recognizing the right assets to maximize the investment returns. In this paper, we focus on the idiosyncratic volatility values and pre-calculate the idiosyncratic volatility values for 31,198 members of NYSE, Amex and Nasdaq markets for the trades occurring between January 1963 and December 2019. Utilizing a subset of dataset, limited to Nasdaq100 index, we consider the application of machine learning techniques in predicting the idiosyncratic volatility values using the raw trade data to explore a data extension option for the future market trade records that have not yet occurred. We offer a deep learning based regression model and compare it with traditional tree-based methods on a small subset of our per-calculated idiosyncratic volatility dataset. Our analytical results show that the performance of the deep learning techniques is much more robust in comparison to that of the traditional tree-based baselines.

This study compares the effects of lecture-based instruction and process-oriented guided inquiry learning (POGIL)-based instruction on the self-efficacy performance of Grade 12 students. A quasi-experimental, pretest-posttest design was adopted to investigate and assess the impact of POGIL-based instruction versus lecture-based instruction on students’ performance as measured by three types of cognitive outcomes; Knowing, Applying and Reasoning (KAR). Two government high schools in Alain were selected as research sites, one for the boys and one for the girls. The total number of participants was approximately 110 students (N=110); 54 were assigned to treatment groups (25 girls and 29 boys), and 56 were assigned to control groups (27 girls and 29 boys). The treatment group was taught a circular motion unit in physics using POGIL-based instruction, while the control group was taught the unit using lecture-based instruction. The study's findings showed statistically significant differences between students of the control group and the treatment group in favour of the latter regarding their science performance, self-efficacy and science-related attitudes. Moreover, positive correlations were found between participants’ performance at the KAR test, self-efficacy and scientific attitudes towards scientific inquiry after the intervention. In conclusion, it is recommended to shift teaching towards POGIL-based instruction due to its positive impact on students’ performance and self-efficacy. It is also suggested to replicate the study to include government and private schools, elementary and high schools, teachers and advisors.

The production of public goods is a necessary condition for the survival of the species but it comes at the expense of individual growth. In a prototype bacterial colony, we model the role of quorum sensing as a resource redistribution mechanism. Two types of bacterial colonies are analyzed, one made up of a single strain and one made up of two different strains. Based on a recent series of experimental data present in the literature, we analyze two types of strains with different extinction times: strains that consume available resources very quickly, therefore becoming extinct quickly, and strains that consume resources slowly and die due to aging. We show that the proposed quorum sensing model describes the main experimental result, namely that coexistence favors the survival of both strains. Furthermore, the production of public goods is maximized when both types of individuals have the maximum proliferation output. Finally, we highlight the role played by so-called dormant cells in the duration of survival time. These cells are of particular interest, because their ability to counteract different types of stress (e.g. the use of antibiotics) still constitutes a challenge.

Background: Endometriosis is a female chronic inflammatory disease in which endometrial tissue develops outside the uterine cavity. It is a complex pathology, that significantly contributes to morbidity in premenopausal women, leading to chronic pain, infertility, and subfertility negatively impacting the physical, and emotional well-being and overall quality of life. The public health burden of endometriosis remains elusive and challenging to determine, and this uncertainty can lead to inadequate healthcare services and treatments. Objective: To estimate the incidence and prevalence of endometriosis in Italy using the hospital discharge records database. Population-based retrospective study. Nationwide between 2011 and 2020. Methods: From the National Hospital Discharge Database were selected all admissions with a diagnosis of endometriosis (ICD-9-CM, codes 617.x), supported by the presence of a procedure code of laparoscopy or any other surgical procedure allowing direct visualisation of the lesions. Main outcomes measures Incidence and prevalence of endometriosis were estimated for the entire 2010-2020 period and by individual year, analysing the time trend and variability in different geographical areas of Italy. Results: A total of 134,667,646 women aged 15–50 years with one or more hospitalisations for endometriosis in all Italian hospitals. The incidence of endometriosis in Italy during this period was 0.839 per 1000 women (CI95% 0.834-0.844), exhibiting a statistically significant decreasing trend over the years. A discernible north-south gradient was observed, with higher rates documented in the northern regions. The prevalence rate stood at 14.0 per 1000 during the same period, and a similar north-south geographical gradient was identifiable in the prevalence rates as well. Conclusions: The utilization of national-level hospital data enables the generation of incidence and prevalence data for endometriosis without variations in methods and definitions, facilitating the evaluation of temporal trends and regional comparisons. Understanding and quantifying this phenomenon is essential for appropriate healthcare planning in various Italian regions.

The potential advantages of plant-based interventions in decreasing the incidence and lessening the morbidity and mortality of COVID-19 are yet to be widely acknowledged. Nevertheless, recent publications propose that these interventions could be effective. Our cardiology center conducted an interventional study in which we incorporated plant-based foods and provided supplementation to 3470 elderly COVID-19 patients with multiple comorbidities. We pay close attention to the precise selection of food items, the application of appropriate processing methods, and the provision of nourishing meals to our patients. Our outcome was highly successful as we achieved a zero mortality rate, and none of our patients experienced worsening conditions or required hospitalization. In this review article we present the mechanisms how plant-based and supplement interventions can mitigate COVID-19 disease severity and mortality. And experts have validated our hypotheses very recently. The measures and methods used to address the ongoing SARS-CoV-2 pandemic through plant-based interventions and supplements are effective and may help prevent or manage future pandemics.

Abstract: This study aims to evaluate the effectiveness of plant-based diets and supplement interventions in mitigating the severity and mortality of COVID-19 patients. Observational research suggests that a diet high in plant-based foods may decrease the likelihood and severity of SARS-CoV-2 infection. However, several studies have faced criticism regarding the accuracy of obtaining dietary questionnaires and the insufficient intake of essential vitamins and minerals in such diets. To address these issues, this study employed a prospective interventional design that strictly controlled the quality, quantity, and processing of plant-based foods provided. Furthermore, the study incorporated supplementation, which enhanced the anti-viral, anti-inflammatory, antioxidant, antithrombotic, and immunomodulatory properties of a plant-based diet against the SARS-CoV-2 virus. Of the 3,470 COVID-19 elderly patients, half already followed a plant-based diet, and the other half new patients, both with various comorbidities, were intervened with a plant-based diet and supplementation. The results showed that the participants in the non-plant-based diet group were twice as likely to have experienced moderate disease (with 95% confidence limit: 1.42-3.12) and 2.4 times more likely to have experienced severe disease (with 95% confidence limit: 1.2-5.0) with a significant p-value of less than 0.0005 and 0.016 respectively, compared to those in the PBD group. During the interventions, none of the participants experienced disease progression or hospitalization, and there were no reported deaths by the end of the study. The outcome was highly favorable and aligned with the researchers' expectations, as COVID-19 morbidity and mortality rates in Indonesia were among the highest in Asia. This research may provide significant insights into the prevention and management of COVID-19 and aid in better preparation for future pandemics.

Chitosan is a copolymer of β-glucosamine and N-acetylglucosamine. Recent experiments showed that the degree and pattern of acetylation along the chitosan chain modulate the biological and physicochemical properties; however, the molecular mechanism is unknown. Here we apply the de novo all-atom molecular dynamics (MD) simulations to study chitosan’s self-assembly process at different degrees of acetylation and two different acetylation patterns. The simulations revealed that the 10-mer chitosan chains with 50% acetylation in either block or alternating patterns associate to form ordered nanofibrils comprised of mainly antiparallel chains in agreement with the fiber diffraction data of deacetylated chitosan. Surprisingly, regardless of the acetylation pattern, the same intermolecular hydrogen bonds mediate the fibril sheet formation while water-mediated interactions stabilize the sheet-sheet stacking. Moreover, the acetylated units are involved in forming the strong intermolecular hydrogen bonds (NH–O6 and O6H–O7), which offers an explanation for the experimental observation that increased acetylation lowers chitosan’s solubility. Taken together, the present study provides the atomic-level understanding the role of acetylation plays in modulating chitosan’s physiochemical properties, contributing to the rational design of chitosan-based materials with the ability to tune by its degree and pattern of acetylation. Additionally, we disseminate the improved molecular mechanics parameters that can be applied in MD studies to further understand chitosan-based materials.

The process of Targeted Opinion Word Extraction (TOWE), a critical component of aspect-based sentiment analysis (ABSA), revolves around identifying opinionated words linked to specific aspect-terms within sentences. Existing deep learning approaches, while effective, often overlook the syntactic structure of sentences, a factor that previous studies have identified as beneficial for TOWE. In this study, we introduce the Syntactic-Enhanced Deep Learning Model (SEDLM) that integrates syntactic structures into deep learning frameworks for TOWE. Our approach leverages syntax-driven opinion potential scores and syntactic inter-word connections, enhancing model performance. Additionally, we introduce an innovative regularization strategy aimed at distinguishing word representations in TOWE tasks. Our comprehensive analysis reveals that SEDLM sets new benchmarks in performance across multiple standard datasets.

The implementation of Boolean functions using Nano crossbar- based switching lattices has been suggested as a substitute for conventional CMOS-based approaches in digital circuits . This alternative may satisfy the needs of future electronic designs, con- sidering the expected end of Moore’s law. This study introduces CVM, a Crossbar-based circuit Verification through Modeling tech- nique

Castor oil may be differentiated from other non-edible vegetable oils because of its main composition of hydroxylated fatty acids. Ricinoleic acid comprises 80–90% wt. of fatty acids in castor oil (Ricinus communis). In this study, the thermo-oxidative stability and tribological behavior of bio-based lubricant samples synthesized from castor oil using isoamyl alcohol were evaluated. Initially, the compositional and physicochemical properties of the obtained samples were assessed using 1H NMR, FTIR, and ASTM methods. Oxidative stability of the samples was evaluated using Rancimat method at 110 °C under air flow. The final biolubricant sample (BL2), obtained after esterification, epoxidation, and oxirane rings opening reactions, presented an oxidation stability time (OST) of 14.3 h. The thermal stability was also evaluated by thermogravimetry (TG) from the mass variations under inert and oxidative atmosphere. BL2 showed higher thermal stability compared to the other samples, demonstrating higher decomposition temperatures in both inert (339.04 °C) and oxidative (338.47 °C) atmospheres, for a mass loss of 50%. The tribological properties of the samples were evaluated using a four-ball tribometer configuration. The BL1 and BL2 samples exhibited lower friction coefficients than the mineral oil sample (MOS) by 21.5% and 43.1%, respectively. Regarding wear, the observed wear scar diameter (WSD) was also lower in BL1 and BL2 compared to MOS by 5.2% and 40.4%, respectively. The results of the tribological evaluation suggest that both samples obtained in this study have promising potential for applications in lubricating machines and mechanical systems.

As formally is known, nanozymes are the nanomaterials or nanoscale materials which reveal enzyme-like properties. These nanomaterilas can be utilzied instead of the natural enzymes for simulation of enzymatic reactions in harsh environmental conditions. Among different nanoscale enzyme-like materials, the majority of them reveal peroxidase-like activity, due to the high catalytic efficiency and stability of peroxidase-like nanozymes, they had been widely utilized for sensing and detection via constructing the colorimetric and fluorescence-based analytical and bioanalytical sensors. There are several high impact nanozymatic sensors which reported in the literature. Although the review articles published in this field, however, the current reviews focus on the introducing nanozyme field not description on the best articles published in this filed. Hence, this article aimed to present a brief introduction on the nanozyme-based chemistry with emphasizing on the historical overview of recent nanozymatic sensors. In this regard the best nanozymatic sensors which published over 2016-2023 were briefly described and overviewed.

Waste management is a significant issue that Indonesia must face. The presence of waste will always exist as long as life continues. One of the main challenges in waste management is the proper separation of organic and inorganic waste. As a solution to address this issue, the Ministry of Environment has made efforts to develop Waste Banks. However, it also creates new problems related to manual data collection, lack of monitoring by the community in implementing waste management activities, and a lack of specific reports regarding waste management conducted by officers. We propose the creation of a website using the Agile Development SDLC method. This website involve several steps and incorporate functions for data digitalization and expedited data collection, such as the addition of QR Code functionality, Monthly Reporting Function, and enhanced data security. The method used in this research is Agile Development. The application has been developed with a user-friendly interface and the latest web development technologies to ensure smooth performance. Overall, the web-based application for organic and inorganic waste using Laravel is an important step to promoting sustainable waste management practices.

In this work, the inhibition properties of new bio-based lignine ILs on the corrosion of mild steel in an aqueous solution of 0.01 M NaCl were investigated by Potentiostatic Electrochemical Impedance Spectroscopy (PEIS), Cyclic Potentiodynamic Polarization (CPP). Moreover, the surface was characterized using SEM, EDS, and optical profilometry. The influence of cation and anion on the inhibitor properties and a possible synergistic effect were investigated. The IL choline syringate showed a promising performance, reducing the corrosion current after 24-hour immersion in 0.01 M sodium chloride, from 1.66 µA/cm2 for the control to 0.066 µA/cm2 with 10 mM of the IL present. In addition to the performance as a corrosion inhibitor, both components of this IL also meet or exceed current additional desired properties of such compounds, being readily available, economically efficient, and well tolerated in organisms and the environment.

Paper-based analytical devices have been substantially developed in recent decades. Many fabrication techniques for paper-based analytical devices have been demonstrated and reported. Herein we report a relatively rapid, simple, and inexpensive method for fabricating paper-based analytical devices using parafilm hot pressing. We studied and optimized the effect of the key fabrication parameters, namely pressure, temperature, and pressing time. We discerned the optimal conditions, including pressure of 3.8 MPa (3 tons), temperature of 80oC, and 3 minutes of pressing time, with the smallest hydrophobic barrier size (821 µm) being governed by laminate mask and parafilm dispersal from pressure and heat. Physical and biochemical properties were evaluated to substantiate the paper functionality for analytical devices. Wicking speed in the fabricated paper strips was slightly slower than that of non-processed paper, resulting from reducing paper pore size. A colorimetric immunological assay was performed to demonstrate the protein binding capacity of the paper-based device after exposure to pressure and heat from the fabrication. Moreover, mixing in two-dimensional paper-based device and flowing in a three-dimensional counterpart were thoroughly investigated, demonstrating that the paper device from this fabrication process is potentially applicable as analytical devices for biomolecule detection. Fast, easy, and inexpensive parafilm hot press fabrication presents an opportunity for researchers to develop paper-based analytical devices in resource-limited environments.

Abstract: Calcium-based catalysts are of a high interest for glycerol polymerization due to their high catalytic activity and large availability. However, their poor stability under reaction conditions is an issue. In the present study, we investigated the stability and catalytic activity of Ca-hydroxyapatites (HAps) as one of the most abundant Ca-source in nature. A stochiometric, a Ca-deficient and a Ca-rich HAps have been synthetized and tested as catalysts in the glycerol polymerization reaction. Deficient and stochiometric HAps exhibited a remarkable 100% selectivity to triglycerol at 15 % of glycerol conversion at 245 °C after 8 h of reaction in the presence 0.5 mol.% of catalyst. Moreover, under the same reaction conditions, Ca-rich HAp showed a high selectivity (88 %) to di- and triglycerol at a glycerol conversion of 27 %. Most importantly, these catalysts were unexpectedly stable towards leaching under the reaction conditions based on the ICP-OES results. However, based on the catalytic tests and characterization analysis performed by XRD, XPS, IR, TGA-DSC and ICP-OES, we found that HAps can be deactivated by the presence of the reaction products themselves, i.e., water and polymers.

A project-based module on Sustainable Development Goal number 5, Gender Equality, was im-plemented on 5 different groups of Business English students consisting of a total number of 62 students in higher education. The main purpose of this project was to raise awareness of this goal by means of a flipped method in which students were required to carry out some research on specific areas of the aforementioned goal and work in teams to elaborate oral presentations. Once their findings were shared in class, students were expected to answer a written questionnaire of open-ended questions which were part of a qualitative analysis. Results of this survey showed that not only 90% of the students gained in depth knowledge of this goal, but also 85% had built a positive attitude to take initiative and 80% were optimistic about future gender equality. Finally, 70% of students suggested further social action to curb the problem of gender discrimination. On the whole, the flipped classroom method of learning combined with project-based group work have proven to be an effective way to raise awareness of this goal, create a more positive attitude, in-crease their willingness to take action as well as widening their English lexical resources.

Object-Based Image Analysis (OBIA) has been successfully used to map slums. In general, the occurrence of uncertainties in producing geographic data is inevitable. However, most studies concentrated solely on assessing the classification accuracy and neglecting the inherent uncertainties. Our research analyses the impact of uncertainties in measuring the accuracy of OBIA-based slum detection. We selected Jakarta as our case study area, because of a national policy of slum eradication, which is causing rapid changes in slum areas. Our research comprises of four parts: slum conceptualization, ruleset development, implementation, and accuracy and uncertainty measurements. Existential and extensional uncertainty arise when producing reference data. The comparison of a manual expert delineations of slums with OBIA slum classification results into four combinations: True Positive, False Positive, True Negative and False Negative. However, the higher the True Positive (which lead to a better accuracy), the lower the certainty of the results. This demonstrates the impact of extensional uncertainties. Our study also demonstrates the role of non-observable indicators (i.e., land tenure), to assist slum detection, particularly in areas where uncertainties exist. In conclusion, uncertainties are increasing when aiming to achieve a higher classification accuracy by matching manual delineation and OBIA classification.

Web-Based GIS is a platform that deals with the representation, management and storage of locational information for real-time online retrieval, viewing and manipulations. Web-based GIS incorporate all the functions of information systems: gathering, storing, retrieving, visualizing and dissemination of spatial information on the Internet. In modern-day GIS serve as vital means to not only geo-referenced locational information that are been retrieved but also the development in web-based technologies as well as there involvements in decision making processes. In recent time the increased used of GIS on the Internet have totally transformed and made three distinct changes across our GIS environment. These are: (i) how are GIS data being accessed (ii) what are modes of its transmission and (iii) what available GIS functionalities are within the environment for analysis. This paper examines the applications and technologies associated with web-based GIS architectures with an emphasis on the internet GIS based structure and case studies of GIS Web-based applications in MapInfo, Microsoft Silverlight Technology and the ArcGIS Server using ArcGIS JavaScript API.

The objective of this study, which is divided into two parts, is twofold: to address long standing challenges in the sensing of atmospheric turbulence-induced wavefront aberrations in strong scintillation conditions via comparative analysis of several basic scintillation resistant wavefront sensing (SR-WFS) architectures and iterative phase retrieval (IPR) techniques (Part I, this paper), and to develop a framework for the potential integration of SR-WFS techniques into practical closed-loop non-astronomical atmospheric adaptive optics (AO) systems (Part II). In this paper we consider basic SR-WFS mathematical models and phase retrieval algorithms, tradeoffs in sensor design and phase retrieval technique implementation, and methodologies for WFS parameter optimization and performance assessment. The analysis is based on wave-optics numerical simulations imitating realistic turbulence-induced phase aberrations and intensity scintillations, and optical field propagation inside SR-WFSs. Several potential issues important for practical implementation of SR-WFS and IPR techniques such as requirements for phase retrieval computational grid resolution, tolerance with respect to optical element misalignments, and the impact of camera noise and input light non-monochromaticity are also considered. Results demonstrate that major wavefront sensing requirements desirable for AO operation in strong intensity scintillations can potentially be achieved by transitioning to novel SR-WFS architectures based on iterative phase retrieval techniques.

This paper presents a novel segmentation algorithm specially developed for applications in 3D point clouds with high variability and noise, particularly suitable for heritage building 3D data. The method can be categorized within the segmentation procedures based on edge detection. In addition, it uses a graph-based topo-logical structure generated from the supervoxelization of the 3D point clouds, which is used to make the clo-sure of the edge points and to define the different segments. The algorithm provides a valuable tool for generating results that can be used in subsequent classification tasks and broader computer applications dealing with 3D point clouds. One of the characteristics of this segmentation method is that it is unsupervised, which makes it particularly advantageous for heritage applications where labelled data is scarce. It is also easily adaptable to different edge point detection and supervoxelization algorithms. Finally, the results show that the 3D data can be segmented into different architectural elements, which is important for further classification or recognition. Extensive testing on real data from historic buildings demonstrates the effectiveness of the method. The results show superior performance compared to three other segmentation methods, both globally and in the segmentation of planar and curved zones of historic buildings.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

With the megatrend of digitalization, the demand for sensors in previously difficult to access scenarios is increasing. Filament-shaped sensors (FSS) are ideal for this demand especially in applications in which the monitoring of textile structures is the focus. Electrically conductive bicomponent filaments based on thermoplastic polyurethane (TPU) and doped with carbon nanotubes (CNTs) offer great potential due to the flexible mechanical properties. Through the core-conducting, bicomponent structure the sensing material is protected from environmental factors such as surrounding conductive materials and external moisture. The insulating material, however, simultaneously complicates the contacting method in order to measure sensing changes in the conductive core. In this work laser cutting is employed as a technology in order to expose the conductive core of the filaments. The filament is then coated with silver and mechanically crimped, providing both a conductive interface for the data acquisition device as well as a protective layer. Laser parameters (power and speed) are investigated in order to identify the parameters with the best cutting properties which is analyzed visually as well as electrically. The work conducted here can then be used in order to provide a robust and reproducible contacting method for core-conducting TPU filaments for strain sensing applications.

Technical components should be produced sustainably and are subject to growing demands in terms of durability and reliability. To meet these expectations, the development of thermochemical processes is auspicious. Titanium alloys, which have a comparatively high gas solubility, allow temporary hydrogen (H) loading, often called thermo hydrogen treatment (THT). THT causes lattice deformation and reduces the β transformation temperature. These effects enable an adjustment of the microstructure, which improves the mechanical properties as compared to those produced conventionally. Furthermore, the process is applicable to complex geometries that cannot be surface hardened by mechanical surface treatment techniques. The investigation presented intends to realize a local microstructure gradient in additively via laser-powder bed fusion (L-PBF) manufactured cylindrical Ti–6Al–4V specimens by changing the distribution and morphology of strengthening precipitates as well as the β grain size depending on the distance to the surface, which should improve the material fatigue properties. To evaluate the mechanical properties of such THT-induced microstructure gradients, the resulting change in fatigue life in the LCF and HCF range was determined by stress-controlled cyclic deformation tests. Besides, the resulting microstructure was characterized by means of XRD and TEM. In addition to the additively manufactured and thermo hydrogen treated cylindrical specimens, conventionally produced tube-like specimens were thermo hydrogen treated and examined. For the THT-induced microstructure gradients, numerically simulated H concentration profiles as well as experimentally determined hardness profiles were used for the evaluation of the THT process. The study shows that H-loading at 500°C and H-degassing at 750°C, followed by aging at 550°C, allows the establishment of a microstructure gradient that shows an 8% improvement in fatigue properties compared to a reference condition without THT. The reason for this improvement is an increased volume fraction secondary alpha phase in the near-surface area of the specimens. Moreover, the results show that the process is applicable a tube-like specimen with varying wall thicknesses.

This paper presents a numerical study on the laser shock wave propagation in a 3D woven CFRP material by means of detailed and homogenized FE models. The aim of the study is to numerically characterize the shock wave response of the 3D woven CFRP in terms of back face velocity profiles and the induced damage and to investigate whether the detailed FE models could be replaced by homogenized FE models. The 3D woven geometry was designed using the TexGen software, while the numerical analyses were executed using the LS-Dyna explicit FE software. A high-strain rate behavior was considered for the matrix. The fiber bundles in the detailed models were modeled as a high fiber content unidirectional composite laminate, with its mechanical properties calculated by micromechanical equations. Both for the fiber bundles of the detailed model and the homogenized models a progressive damage material model was applied. The results of the detailed model reveal a considerable effect of material’s architecture on the shock wave propagation and the sensitivity of the back face velocity profile to the spot location. Consequently, the homogenized model is not capable of accurately simulating the shock wave response of the 3D woven composite. Moreover, the detailed predicts with high accuracy matrix cracking in the resin-rich areas and in the bundles as well as fiber failure. On the contrary, the homogenized model predicts matrix cracking at the same areas and no fiber failure.

This paper is a follow-up to a previous study that was conducted in a research forest and identified the optimal method for Diameter at Breast Height (DBH) estimation as a circular scanning and fitting ellipses to 4cm stem cross-sections at breast height. The aim of this study was to determine whether the identified method is applicable to natural boreal forests as well. The iPad Pro LiDAR scanner was used to acquire point clouds for 15 sites representing a range of natural boreal forest conditions in Ontario, Canada, and estimate DBH. The secondary objective was to determine if tested stand (Species composition, age, density, understory) or tree (Species, DBH) factors affected the accuracy of estimated DBH. Overall, estimated DBH values were within 1cm of actual DBH values for 78 of 133 measured trees (59%). An RMSE of 1.5cm (8.6%) was achieved. Stand age had a large effect (>0.15) on the accuracy of estimated DBH values, while density, understory, and DBH had moderate effects (0.05-0.14). No trend was identified between accuracy and stand age. Accuracy improved as understory density decreased and as tree DBH increased. Inertial Measurement Unit (IMU) and positional accuracy errors with the iPad Pro scanner limit the feasibility of using this device for forest inventories.

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

Laser marking on polymer composite surfaces can be difficult to contrast and cause readability problems for electronic decoding equipment on production lines due to poor interaction between the laser and the fibres used to reinforce these materials. This problem can be solved with the right choice of marking parameters, resulting in savings for companies by avoiding production problems such as rejection, scrap and customer complaints. The present work uses the PBT/glass fibre composite used in the manufacture of instrument panels for motorcycles. The tests were carried out with different laser marking parameters using a Nd: YAG laser. Subsequently, the laser-marked DMC codes were analysed using a Verifier to evaluate the quality according to the ISO/IEC 29158:2020 standard. A detailed analysis of these surfaces was also carried out to observe some physical and chemical changes using SEM microscopy and EDS spectroscopy. The optical analysis showed that the lower the radiation power and pulse frequency and the higher the marking speed, the weaker the laser marking and therefore the poorer the DMC code quality, which was confirmed by the SEM. EDS spectroscopy showed that the laser marking process did not affect the chemical changes on the sample surface.

Statistical analysis of mechanical properties of thin-walled samples (~500 microns) obtained by selective laser melting from AlSi10Mg material and subjected to heat treatment for 1 hour at temperatures from 260 °C to 440 °C (step of aging temperature change 30 °C) has shown that the maximum strain hardening in the stretching diagram section from yield strength to tensile strength is achieved at the heat treatment temperature equal to 290 °C. At carrying out of correlation analysis statistically significant positive correlation between deformation corresponding to yield strength and the sum of heights of the largest protrusions and depths of the largest depressions of the surface roughness profile within the basic length of the sample (Rz) and the full height of the surface roughness profile (Rmax) was established. It was found that the reason for the correlation is the presence of cohesive states between the extreme values of the surface roughness profile that persist along the entire length of the specimen.

Early spaceborne laser altimetry mission development starts in pre-phase A design, where diverse ideas are evaluated against mission science requirements. A key challenge is predicting realistic instrument performance through forward modeling at arbitrary spatial scale. Analytical evaluations compromise accuracy for speed, while radiative transfer modeling is not applicable at global scale due to computational expense. Instead of predicting arbitrary properties of a lidar measurement, we develop a baseline theory to predict only the distribution of uncertainty specifically for the terrain elevation retrieval based on terrain slope and fractional canopy cover features through a deep neural network gaussian mixture model, also known as a mixture density network (MDN). Training data was created from differencing geocorrected GEDI L2B elevation measurements with 32 independent reference lidar datasets in the contiguous U.S. from the National Ecological Observatory Network. We trained the MDN and selected hyperparameters based on regional distribution predictive capability. On average, the relative error of equivalent standard deviation of predicted regional distributions was 15.9%, with some anomalies in accuracy due to generalization and insufficient feature diversity and correlation. As an application, we predict the percent of elevation residuals of a GEDI-like lidar within a given mission threshold from 60°S to 78.25°N, which correlate to qualitative understanding of prediction accuracy and instrument performance.

Field electron emission, or electron tunneling through a potential barrier under the influence of a strong electrostatic field, is of broad interest to the accelerator physics community. For example, it is the source of undesirable dark currents in resonant cavities, providing a limit to high-field operation. The classical approach to field electron emission is the Fowler-Nordheim (FN) framework, which incorporates a simplified surface potential and various assumptions. Here we build a more realistic model using the potential and charge densities derived from a density-functional theory (DFT) calculation. We examine the correction factors associated with each model assumption. Compared to the FN framework, our results can be extended up to 80 GV/m, a limit that has been reached in laser-induced strong field emission scenarios.

Various vestibuloplasty techniques have been reported to increase the attached mucosa (AM) and vestibular depth around dental implants. However, these surgical methods have disadvantages, such as limitations in manipulation, necessity of suturing, postoperative discomfort, swelling, and pain. This study aimed to evaluate the efficacy of laser-assisted periosteal fenestration (LA-PF) in treating a patient with a shallow vestibule and insufficient AM around dental implants. The LA-PF technique was performed using an Er:YAG laser. First, a partial-thickness apically positioned flap (APF) was performed. Horizontal periosteal fenestration was performed using an Er:YAG laser to expose the bones. Periosteal suturing was not required. After 12 months, sufficient AM and deepened vestibule were obtained and maintained. Thus, the LA-PF technique may be a simple and predictable treatment modality for vestibuloplasty around dental implants.

The purpose of this paper is to study the influence of diffusion and thermal loading due to pulsed laser heating on a thermoelastic solid with voids in the context of the model of three-phase-lag. The non-dimensional governing equations are formulated and then the exact expressions for the temperature field, the displacement components, the stress components, the concentration field and the change in the volume fraction field are obtained using the normal mode technique. The material is an isotropic, homogeneous elastic half-space and heated by a non-Gaussian laser beam with pulse duration of ps. The magnesium crystal element is used as an application to compare the predictions induced by diffusion and laser pulse on poro-thermoelastic medium of the model of three-phase-lag with those for the theory of Green–Naghdi of type III. The results obtained for thermal changes are verified by comparison with two theories of thermoelasticity, namely the model of three-phase lag (3PHL) and the Green and Nagdi type III theory. Plot the expressions to examine the effect of the laser pulse at two different values of time and the effect void parameter. This study also yields some interesting special cases.

The surface defects of shield subway tunnel can significantly affect the serviceability of the tunnel structure and may compromise the operation safety. To effectively detect the multiple surface defects, this research employs a tunnel inspection trolley (TIT) based on the mobile laser scanning technique. By conducting the inspection of the shield tunnel on a metro line section, various surface defects are identified by the TIT, including water leakage defect, dislocation, spalling, cross-section deformation, etc. To explore the root causes of the surface defects, the association rules between different defects are calculated via an improved Apriori algorithm. Results show that: i) there are significant differences in different association rules of various surface defects of the shield tunnel; ii) the average confidence of the association rule “dislocation & spalling → water leakage” is as high as 57.78%, indicating that most of the water leakage defects are caused by dislocation and spalling of the shield tunnel in the sections being inspected; iii) the weakest rule appears at “water leakage → spalling”, with the average confidence of 13%. The association analysis can be used in predicting the critical defects influencing the structural reliability and operation safety, such as water leakage, and optimizing the construction and maintenance work for the shield subway tunnel.

In this paper, the stabilization and high efficiency of an unstable Second Harmonic Generation (SHG) of a Nd : YVO4 laser with a KTP intracavity is carried out by using a passive Q-switching crystal and a parametric modulation method (harmonic modulation) is shown. The harmonic modulation was defined as um(t) = Amsin(2π fmt), with modulation amplitude as Am(Vpp), and modulation frequency as fm(Hz), applied to the pumping of the Nd : YVO4 -KTP laser to control the amplitude and frequency of the emission, thus stabilizing the dynamic states of this laser. The promising application of this green light source is materialized when such light is necessary for high-density optics, such as in the treatment materials industry or in some aesthetic applications.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

The mechanical properties and stability of hydrophobic surface structures prepared by traditional methods are still the main technical bottlenecks restricting the broad application of hydrophobic systems on workpiece surfaces. In this contribution, we propose a technique called selective laser shock peening (SLSP) to enable large-scale high efficient, low-cost manufacturing of hydrophobic metal surfaces with enhanced mechanical properties for durable applications. Using the method of experimental investigation combined with numerical calculation, the hydrophobic properties, mechanical properties, and tribological properties of the samples prepared under SLSP, all-laser shock peening (ALSP), and non-laser shock peening (NLSP) are studied. The SLSP process could prepare a 3D gradient structure material with surface structures, a two-phase (strong phase, soft phase) distribution on the surface, and a multi-level gradient distribution in the thickness direction. Compared with the 2D gradient structure prepared by the traditional process, 3D gradient structures by SLSP have more significant advantages in improving the wetting behavior and the mechanical properties of the material, which proves SLSP to be a novel method to fabricate functional metal surface structures, with highly high engineering application value.

This paper considers the principles of building a circuit model of film resistor cutting. The conductive resistive medium is defined with the component equations and the topology of the circuit model. A method of estimating the electric parameters of a resistor operating in the system with a measuring voltage source is shown. An equation system for the node voltages is defined, and the resistive layer parameters are analyzed as the circuit model structure changes during the cutting process.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

The application of electrospray ionization mass spectrometry (ESI-MS) as a direct method for detecting reactive intermediates is a technique of developing importance in the routine monitoring of solution-phase reaction pathways. Here, we utilize a novel on-line photolysis ESI-MS approach to detect the photoproducts of riboflavin in aqueous solution under mildly alkaline conditions. Riboflavin is a constituent of many food products, so its breakdown processes are of wide interest. Our on-line photolysis setup allows for solution-phase photolysis to occur within a syringe using UVA LEDs, immediately prior to being introduced into the mass spectrometer via ESI. Gas-phase photofragmentation studies via laser-interfaced mass spectrometry of deprotonated riboflavin, [RFH], the dominant solution-phase species under the conditions of our study, are presented alongside the solution-phase photolysis. The results obtained illustrate the extent to which gas-phase photolysis methods can inform our understanding of the corresponding solution-phase photochemistry. We determine that the solution-phase photofragmentation observed for [RFH] closely mirrors the gas-phase photochemistry, with the m/z 241 ion being the only major condensed-phase photoproduct. Further gas-phase photoproducts are observed at m/z 255, 212, and 145. The value of exploring both the gas- and solution-phase photochemistry to characterize photochemical reactions is discussed.

With the aim to investigate the effect of parameter and quenching process on the joint of hot stamping steel by laser welding, the BR1500HS boron steel was welded by filling-wire laser welding with ER70-G welding wire under different parameters. The welded specimens were heated to 900℃ and held for 5min before water quenching. The universal material test machine, Optical micro-scope, Vickers hardness tester, scanning electron microscope and electron backscatter diffraction (EBSD) were used to characterize. The results showed that the macroscopic morphology of fusion zone (FZ) becomes from funnelform to hyperbolic curve shape when heat input increases and from hyperbolic curve shape to funnelform when wire-feed speed increases. The strength after quenching is more than 1557Mpa at heat input of 1040J/cm, wire feeding speed of 1.6m/min~1.8m/min and welding speed of 1.5m/min. EBSD test showed that the FZ and fine grain zone (FGZ) have more retained austenite (RA) than coarse grain zone (CGZ) before quenching and RA in FZ and heat affect zone (HAZ) decreased and distributed uniformed after quenching. The grain diameter in FZ distribute unevenly, with the maximum grain diameter larger than 40μm before quenching. After quenching, the grain diameter of FZ, HAZ and BM is more even and coarse grains in the FZ was refined. Before quenching, the microhardness of FZ and HAZ is of 450HV~500HV at different heat input and wire-feed speed and all region of joint keeps at 450HV~550HV after quenching. Most dimple and little river pattern in the joint fracture mor-phology before quenching indicates a well plasticity and most cleavage facet is observed after quenching due to the joint combine with martensite.

In this paper, we introduce a computational procedure that enables autonomous LEO laser trackers endowed with INSs to increase the current accuracy when shooting at middle distant medium-size LEO debris targets. The code is designed for the trackers to throw the targets into the Atmosphere by means of ablations. In case that the targets are eclipsed to the trackers by the Earth, the motions of the trackers and targets are modeled by equations that contain post-Newtonian terms accounting for the curvature of space. Otherwise, when the approaching targets become visible for the trackers, we additionally use more accurate equations, which allow to account for the local bending of the laser beams aimed at the targets. We observe that under certain circumstances the correct shooting configurations that allow to safely and efficiently shoot down the targets, differ from the current estimations by distances that may be larger than the size of many targets. In short, this procedure enables to estimate the optimal shooting instants for any middle distant medium-size LEO debris target.

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

Ti-6Al-4V (TC4) titanium alloy parts were successfully fabricated by laser melting deposition (LMD)technology in this study. Proper normalizing temperatures were presented in detailed for bulk LMD specimens. Optical microscope, scanning electron microscopy, X-ray diffraction and electronic universal testing machine were used to characterize the microstructures, phase compositions, the tensile properties and hardness of the TC4 alloy parts treated using different normalizing temperature. The experimental results showed that the as-fabricated LMD speceimens microstructures mainly consisted of α-Ti phase with a small amount of β-Ti phase. After normalizing treatment, in the area of α-Ti phase, the recrystallized length and width of α-Ti phase both increased. When normalizing in the (α+β) phase field, the elongated primary α-Ti phase in the as-deposited state was truncated due to the precipitation of β-Ti phase and became a short rod-like primary α-Ti phase. In as-fabricated microstructure, the β-Ti phase was precipitated between different short rod-shaped α-Ti phases distributed as basketweave. After normalizing treatment at 990 for two hours with subsequent air cooling, the TC4 titanium alloy had significant different microstructures from original sample produced by LMD. Moreover, the mismatch of tensile and hardness property was mitigated in this heat treatment. So the normalizing treatment methods and temperature can be qualified as a prospective heat treatment of titanium alloy fabricating by laser melting deposition.

Structure quality of LuFeO3 epitaxial layers grown by pulsed-laser deposition on sapphire substrates with and without platinum interlayers has been investigated by in-situ high-resolution x-ray diffraction (reciprocal-space mapping). The parameters of the structure such as size and misorientation of mosaic blocks have been determined as functions of the thickness of LuFeO3 during the PLD growth and for different platinum interlayers thicknesses up to 40 nm. The x-ray diffraction results combined with ex-situ scanning electron microscopy and high-resolution transmission electron microscopy demonstrate that the Pt interlayer significantly improves the structure of LuFeO3 by reducing the misfit of the LuFeO3 lattice with respect to the material underneath.

This work examines atomic and molecular signatures in laser-induced plasma in standard ambient temperature and pressure environments, including background contributions to the spectra that depend on the laser pulse-width. Investigations include solids, gases, and nano-particles. Abel inversions of measured line-of-sight data reveal insight into the radial plasma distribution. For nominal 6 nanosecond laser pulses and for pulse-energies in the range of 100 to 800 milli-Joules, expansion dynamics and turbulence due to shock phenomena are elucidated to address local equilibrium details that are frequently assumed in spatially averaged emission spectroscopy. Chemical equilibrium computations reveal temperature dependence of selected plasma species. Specific interests include atomic hydrogen (H) and cyanide (CN). The atomic H spectra, collected following optical breakdown in ultra-high-pure hydrogen and 9:1 mixtures of ultra-pure hydrogen and nitrogen gases, indicate spherical shell structures and isentropic expansion of the plasma kernel over and above the usual shockwave. The recombination radiation of CN emanates within the first 100 nanoseconds for laser-induced breakdown in a 1:1 CO₂:N₂ gas mixture when using nanosecond laser pulses to create the micro-plasma. The micro-plasma is generated using 1064 nm, 150 mJ, 6 ns Q-switched Nd:YAG laser radiation. Measurements of the optical emission spectra utilize a 0.64 m Czerny-Turner type spectrometer and an intensified charge-coupled device.

Micro-plasma is generated in ultra-high-pure hydrogen gas filled inside a cell at a pressure of (1.08 ± 0.033) × 10⁵ Pa (810 ± 25 Torr) by using a Q-switched Nd:YAG laser device operated at 1064 nm wavelength and 14 ns pulse duration. Micro-plasma emission spectra of the hydrogen Balmer alpha line, H_α, are recorded with a Czerny-Turner type spectrometer and an intensified charge-coupled device. The spectra are calibrated for wavelength and corrected for detector sensitivity. During the first few tens of nanoseconds after initiating optical breakdown, significantly Stark-broadened and Stark-shifted H_α lines mark the well-above hypersonic outward expansion. The vertical diameters of the spectrally resolved plasma images are measured for time delays of 10 ns to 35 ns to determine expansion speeds of the order of 100 km/s to 10 km/s. For time delays of the order of 0.5 µs to 1 µs, the expansion decreases to the speed of sound of 1.3 km/s in the near ambient temperature and pressure hydrogen gas.

A numerical model was developed for predicting the bead geometry and microstructure in Laser Beam Welding of 2 mm thickness Inconel 718 sheets. The experiments were carried out with a 1 kW maximum power fiber laser coupled with a galvanometric scanner. Wobble strategy was employed for sweeping 1 mm wide circular areas for creating the weld seams and a specific tooling was manufactured for supplying protective Argon gas during the welding process. The numerical model takes into account both the laser beam absorption and the melt-pool fluid movement along the bead section, resulting in a weld geometry that depends on the process input parameters, such as feed rate and laser power. The microstructure of the beads was also estimated based on the cooling rate of the material. Features as bead upper and bottom final shapes, weld penetration and dendritic arm spacing were numerically and experimentally analyzed and discussed. The results given by the numerical analysis agree with the tests, making the model a robust predictive tool.

LASER cladding is a technique which has as main purpose to improve mechanical properties of materials surface with the addition of thin layers of other materials. Cladding/coating/addition material can be transferred to the substrate by powder injection, wire feeding or paste feeding and by the method of pre-placing the powders on the substrate. LASER cladding as a technique has only about 40 years. Is not yet a current technology and more work is needed, namely in the characterization of mechanical properties of new alloys used as base or cladding materials in this process. In this paper will be done initially an historical approach, followed by a description of the principles of the LASER cladding, a description of the applicability of the process and its advantages and limitations and the paper will end with a state of the art about the advances in new metallic alloys. So, this paper presents a review and the state of the art of the technological process and will be a contribution for the divulgation of this recent technique.

Maximum hardness and hardened depth are the responses of interest in relation to the laser hardening process. These values define heat treatment quality and have a direct impact on mechanical performance. This paper aims to develop models capable of predicting the shape of the hardness profile depending on laser process parameters for controlling laser hardening quality (LHQ), or rather the response values. An experimental study was conducted to highlight hardened profile sensitivity to process input parameters such as laser power (P_L), beam scanning speed (V_S) and initial hardness in the core (H_C). LHQ modeling was conducted by modeling attributes extracted from the hardness profile curve using two effective techniques based on the punctual and geometrical approaches. The process parameters with the most influence on the responses were laser power, beam velocity and initial hardness in the core. The obtained results demonstrate that the geometrical approach is more accurate and credible than the punctual approach according to performance assessment criteria.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

A significant number and range of challenges besetting sustainability can be traced to the actions and interactions of multiple autonomous agents (people mostly) and the entities they create (e.g., institutions, policies, social network) in the corresponding social-environmental systems (SES). To address these challenges, we need to understand decisions made and actions taken by agents, the outcomes of their actions, including the feedbacks on the corresponding agents and environment. The science of Agent-based Complex Systems—ACS science—has a significant potential to handle such challenges. The advantages of ACS science for sustainability are addressed by way of identifying the key elements and challenges in sustainability science, the generic features of ACS, and the key advances and challenges in modeling ACS. Artificial intelligence and data science promise to improve understanding of agents’ behaviors, detect SES structures, and formulate SES mechanisms.

Wearable assistant devices play an important role in daily life for people with disabilities. Those who are hearing impaired may face dangers while walking or driving on the road. The major danger is their inability to hear warning sounds from cars or ambulances. Thus, the goal of this study is to develop a wearable assistant device for the hearing impaired to recognize emergency vehicle sirens on the road using edge computing. An EfficientNet-based fuzzy rank-based ensemble model was proposed to classify seven audio sounds, including human vocalizations and emergency vehicle sirens. This model was embedded in an Arduino Nano 33 BLE Sense development board. The audio files were respectively obtained from the CREMA-D dataset and Large Scale Audio dataset of emergency vehicle sirens on the road, with a total number of 8756 files. The seven audio sounds included neutral vocalization, anger vocalization, fear vocalization, happy vocalization, car horn sound, siren sound, and ambulance siren sound. The audio signal was converted into a spectrogram by the short-time Fourier transform as the feature. When one of the car horns, sirens, or ambulance sirens was detected, the wearable assistant device presented alarms through vibration and messages on the OLED panel. The performances of the EfficientNet-based fuzzy rank-based ensemble model in offline computing achieved an accuracy of 97.1%, precision of 97.79%, sensitivity of 96.8%, and specificity of 97.04%. In edge computing, the results were an accuracy of 95.2%, precision of 93.2%, sensitivity of 95.3%, and specificity of 95.1%. Thus, the proposed wearable assistant device has the potential benefit of helping the hearing impaired avoid traffic accidents.

Graphene-based nanomaterials (GNMs), including graphene, graphene oxide, reduced graphene oxide, and graphene quantum dots, may have direct anticancer activity or be used as nanocarri-ers for antitumor drugs. GNMs usually enter tumor cells by endocytosis and can accumulate in lysosomes. This accumulation prevents drugs bound to GNMs from reaching their targets, sup-pressing their anticancer effects. A number of chemical modifications are made to GNMs to facili-tate the separation of anticancer drugs from GNMs at low lysosomal pH and to enable lysosomal escape of drugs. Lysosomal escape may be associated with oxidative stress, permeabilization of the unstable membrane of cancer cell lysosomes, release of lysosomal enzymes into the cytoplasm, and cell death. GNMs can prevent or stimulate tumor cell death by inducing protective autopha-gy or suppressing autolysosomal degradation, respectively. Furthermore, because GNMs prevent bound fluorescent agents from emitting light, their separation in lysosomes may enable tumor cell identification and therapy monitoring. In this review, we explain how the characteristics of the lysosomal microenvironment and the unique features of tumor cell lysosomes can be exploited for GNM-based cancer therapy.

This study was designed to extend the literature on multicomponent interventions for the children of deaf adults (CODA) population. This study used two evidence-based behavior intervention strategies: pre-session pairing (PSP) and independent group contingency (GC). These strategies have been successfully used to decrease off-task behavior in elementary school children with various abilities and diverse backgrounds. However, the research on multicomponent interventions has yet to examine their effects on the CODA population in inclusive classrooms. This study used a concurrent multiple baseline design across participants with an ABC sequence to examine teacher-implemented PSP with independent GC in reducing the off-task behavior of three CODAs in an inclusive classroom at a public elementary school. The results show that the intervention successfully decreased off-task behavior for all participating CODAs. The results suggest that CODAs can adapt to classroom rules and expectations when PSP and independent GC are systematically applied to them in classrooms.

Event-based vision is an emerging field of computer vision that offers unique properties such as asynchronous visual output, high temporal resolutions, and dependence on brightness changes to generate data. These properties can enable robust high-temporal-resolution object detection and tracking when combined with frame-based vision. In this paper, we present a hybrid, high-temporal-resolution, object detection and tracking approach, that combines learned and classical methods using synchronized images and event data. Off-the-shelf frame-based object detectors are used for initial object detection and classification. Then, event masks, generated per each detection, are used to enable inter-frame tracking at varying temporal resolutions using the event data. Detections are associated across time using a simple low-cost association metric. Moreover, we collect and label a traffic dataset using the hybrid sensor DAVIS 240c. This dataset is utilized for quantitative evaluation using state-of-the-art detection and tracking metrics. We provide ground truth bounding boxes and object IDs for each vehicle annotation. Further, we generate high-temporal-resolution ground truth data to analyze the tracking performance at different temporal rates. Our approach shows promising results with minimal performance deterioration at higher temporal resolutions (48 – 384 Hz) when compared with the baseline frame-based performance at 24 Hz.

The recent covid crisis has proven important lessons for academia and industry regarding digital reorganization. Among fascinating lessons from these times is the huge potential of data analytics and artificial intelligence. The crisis exponentially accelerated the adoption of analytics and artificial intelligence, and this momentum is predicted to continue into the 2020s and over. Moreover, drug development is a costly and time-consuming business, and only a minority of approved drugs return the revenue that exceeds the research and development costs. As a result, there is a huge drive to make drug discovery cheaper and faster. With modern algorithms and hardware, it is not too surprising that the new technologies of artificial intelligence and other computational simulation tools can help drug developers. In only two years of covid research, many novel molecules have been designed/identified using artificial intelligence methods with astonishing results in terms of time and effectiveness. This paper will review the most significant research on artificial intelligence in the de novo drug design for COVID-19 pharmaceutical research.

Maternal-child care is one of the foundations of primary health care. Nurses’ competency skills they have been taught. Community awareness is an important part of preventive healthcare, and nurses must be aware of the factors that impact the health of the community. This study examines the effectiveness of lecture-based instructions in maternal and child care and its implications to students' social competency skills and community awareness in Nursing Colleges in Nueva Ecija, Philippines. The researcher uses survey questionnaire and employed the descriptive design where fifteen (15) nursing students and five (5) teachers were purposively selected. The findings revealed that the weighted mean for the effectiveness of lecture based instruction in maternal and child care is 3.91 with verbal description of “Effective”, the effects of lecture based instruction in maternal and childcare to students’ social competency skills and community awareness got the weighted mean of 3.87 and interpreted as “very satisfactory” and the effectiveness of actual community-based instruction is very effective with weighted mean of 4.25 and is higher compare to lecture based instruction. The results also revealed that students and teachers were challenged in lecture-based instruction in maternal and chi8ldcare during distance learning. Recommendations for the enhancement of lecture-based instruction in maternal and childcare in social competency skills and community awareness were also made.

Over the last decade, a significant literature has emerged that advocates the potential of different Additive manufacturing (AM) technologies and printable polymeric materials. Nevertheless, large scale printing and complex geometric shapes, with curvatures and non-planar layer deposition, are a challenging process for the traditional gantry-based machine. The 3 degrees of freedom cartesian configuration restricted their capability to planar layered printing and restricted part dimensions. To date, many researchers have used industrial robots to overcomes this limitation. This review gives the reader a good overview of the FDM technique due to its scalability, cost efficiency and a wide range of material printability. A strong emphasis is laid on the PLA and PLA-based composites as promising materials for the FDM process applications. The second part of this paper links the successful use of these materials in the traditional printing process to large scale printing using the robot-based FDM process. This survey presents representative setups for robot-based AM and works that have been used these setups for non-planar material deposition. Finally, we conclude this paper by identifying opportunities for realizing new functional capabilities by exploiting robot-based AM, and we also present the future trends in this area.

Saccharomyces cerevisiae are a phenotypically diverse species that adapt to a wide variety of environments by exploiting standing genetic diversity and selecting for advantageous mutations. Glyphosate and copper-based herbicides/ fungicides affect non-target organisms, these incidental exposures can impact microbial populations. In this study, glyphosate resistance was found in the historical collection of yeast which was collected over the last century, but only in yeast isolated after the introduction of glyphosate. The highest glyphosate-resistant yeasts were isolated from agricultural sites. However, herbicide application at these sites was not recorded. In an effort to assess glyphosate resistance and impact on non-target microorganisms, yeast were harvested from 15 areas with known herbicidal histories, including an organic farm, conventional farm, remediated coal mine, suburban locations, state park, and a national forest. Yeast representing 23 genera were isolated from 237 samples of plant, soil, spontaneous fermentation, nut, flower, fruit, feces, and tree material samples. Saccharomyces, Candida, Metschnikowia, Klyveromyces, Hanseniaspora, and Pichia were other genera commonly found across our sampled environments. Managed areas had less species diversity and at the brewery, only Saccharomyces and Pichia were isolated. A conventional farm growing RoundUp Ready™ corn had the lowest phylogenetic diversity and the highest glyphosate resistance. The mine was sprayed with multiple herbicides including a commercial formulation of glyphosate; however, the yeast did not have elevated glyphosate resistance. In contrast to the conventional farm, the mine was exposed to glyphosate only one year prior to sample isolation. Glyphosate resistance is an example of the anthropogenic selection of nontarget organisms.

For centuries, crop plants have represented the basis of the daily human diet. Among them, cereals and legumes, accumulating oils, proteins and carbohydrates in their seeds, distinctly dominate modern agronomic practice. Indeed, these plants play an essential role in the food industry and fuel production. Therefore, the seeds of crop plants are intensively studied by food chemists, biologists, biochemists, and nutritional physiologists. Accordingly, not only seed development and germination, but also age- and stress-related alterations in seed vigor, longevity, nutritional value and safety can be addressed by a broad panel of analytical, biochemical and physiological methods. Currently, functional genomics is one of the most powerful tools, giving direct access to characteristic metabolic changes, accompanying plant development, senescence and response to biotic or environmental stress. Among individual methodological platforms, proteomics represents one of the most effective ones, giving access to cellular metabolism at the level of proteins. Here we discuss the main methodological approaches employed by seed proteomics in the context of physiological changes related to seed development, ageing and response to environmental stress.

This paper presents an in-depth contextualized tutorial on Agricultural IoT (Agri-IoT), covering the fundamental concepts, assessment of routing architectures and protocols, and performance optimization techniques via systematic survey and synthesis of related literature. The negative impacts of climate change and the increasing global population on food security and unemployment threats have motivated the adoption of the wireless sensor network (WSN)-based Agri-IoT as an indispensable underlying technology in precision agriculture and greenhouses to improve food production capacities and quality. However, most related Agri-IoT testbed solutions have failed to achieve their performance expectations due to the lack of an in-depth and contextualized reference tutorial that provides a holistic overview of communication technologies, routing architectures, and performance optimization modalities based on users’ expectations. Thus, although IoT applications are founded on a common idea, each use case (e.g., Agri-IoT) varies based on specific performance and users expectations as well as its technological, architectural, and deployment requirements. Likewise, the agricultural setting is a unique and hostile area where conventional IoT technologies do not apply, hence the need for this tutorial. Consequently, this tutorial addresses these via the following contributions: (1) a systematic overview of the fundamental concepts, technologies, and architectural standards of WSN-based Agri-IoT, (2) an evaluation of the technical design requirements of a robust, location-independent, and affordable Agri-IoT, (3) a comprehensive survey of the benchmarking fault tolerance techniques, communication standards, routing and medium access control (MAC) protocols, and WSN-based Agri-IoT testbed solutions, and (4) an in-depth case study on how to design a self-healing, energy-efficient, affordable, adaptive, stable, autonomous, and cluster-based WSN-specific Agri-IoT from a proposed taxonomy of multi-objective optimization (MOO) metrics that can guarantee an optimized network performance. Furthermore, this tutorial established new taxonomies of faults, architectural layers, and MOO metrics for cluster-based Agri-IoT (CA-IoT) networks and a 3-tier objective framework with remedial measures for designing an efficient associated supervisory protocol for cluster-based Agri-IoT networks.

Background Postpartum hemorrhage (PPH) remains the leading cause of maternal mortality globally, necessitating focused attention from midwifery professionals. To mitigate severe complications and improve maternal outcomes, regular and effective training in PPH rescue techniques is essential. Aim To assess the efficacy of the combination of case-based learning (CBL) and problem-based learning (PBL) with simulation teaching methods to enhance the technical proficiency of midwifery trainees in managing PPH Methods This quasi-experimental study included 76 trainees who received PPH training at Peking University Third Hospital from March to July 2023; they were divided into two groups: the control group (n = 50), which followed traditional simulation training methods, and the research group (n = 26), which used a combination of CBL-PBL and scenario simulation. After training, all participants completed a questionnaire to evaluate their satisfaction with the training program and to measure improvements in clinical thinking, practical skills, relevant knowledge, team cooperation, and management abilities. Statistical analysis was conducted using unpaired t-tests and chi-square tests to compare the groups. Findings The combination of CBL-PBL with scenario simulation was found to be highly satisfactory compared with the traditional simulation training. This approach significantly enhanced self-assessed skills among midwifery trainees in the research group. Additionally, a majority of trainees expressed a preference for the inclusion of regular simulation exercises and detailed discussions on PPH cases in future training sessions. Conclusion Combining CBL-PBL with simulation practice is a more effective teaching method for PPH management training than traditional methods. Future studies should explore the implementation of regular PPH rescue skill training and its effectiveness in real clinical settings to substantiate these findings.

Driven by environmental sustainability concerns, the integration of biobased components in curtain wall systems is gaining traction in both research and the construction market. This paper explores the development and validation of a bio-based façade system within the Basajaun H2020 project. The project aimed to demonstrate the feasibility of introducing environmentally friendly bio-based components into the mature curtain wall façade industry. The paper focuses on identifying technological solutions for replacing key components such as profiles, insulation, and the tightness system with bio-based and less environmental impact alternatives presenting the results achieved in the façade system design of the Basajaun project funded by European Union. These solutions aimed at creating a bio-composite-based curtain wall façade that adheres to current building envelope standards and normative; to implement diverse façade typologies for vision panels, opaque sections, and integrated windows; to engineer the prefabrication process for industrialization, enabling wider market replication and simplified transport and installation. The results demonstrate that the Basajaun façade successfully integrates selected components and meets the performance requirements set by regulations. However, questions remain regarding the workability of bio-based profiles as a commercially viable, ready-to-market solution that can replace traditional aluminum profiles in the curtain wall façade industry.

This review aims to consolidate varied information regarding Port Scanning, and examine the tools, techniques, and detection algorithms used. It explores TCP SYN, Full TCP, UDP, and stealth scans, and shows their functions and abilities. Paired with these techniques, it also shows the tools that they can be used by, such as NMap, Zmap, and MASSCAN. It discusses the various detection techniques such as Signature and Anomaly based detection, and discusses the real world impact of this technology, while commenting on the legal and ethical issues posed.

This study reports the synthesis and characterization of novel per-fluorinated organic polymers with azo- and azomethine-based linkers using nucleophilic aromatic substitution. The polymers reveal variations in the fluorine content via the incorporation of decafluorobiphenyl and hexafluorobenzene linkers, which enhanced their hydrophobic nature. The rich fluorine polymers were slightly soluble in THF and have shown molecular weights between 4886 to 11948 g/mol. All polymers exhibit thermal stability in the range of 350-500°C, with varying thermal stability depending on the fluorine and nitrogen content. Conjugation of the polymers was confirmed through changes in the UV-Vis spectra, with a hypsochromic shift observed in all cases, more pronounced in azo-based fluorinated chains due to H-bonding on the nitrogen sites, chain conformations, and planarity. The optical band gap (Eg) of the polymers was determined from the UV-Vis data, with the Eg values of the azo-based fluorinated polymers being 1 eV higher than those of their corresponding linkers. The cross-linking formation was characterized by porosity measurements, with the azo-based polymer exhibiting the highest surface area of 770 m²/g with a pore volume of 0.35 cm³/g, while the open-chain azomethine-based polymer exhibited the lowest surface area of 285 m²/g with a pore volume of 0.0872 cm³/g. Porous structures with varied hydrophobicities were investigated as adsorbents for separating water-benzene and water-phenol mixtures and selectively binding methane/carbon dioxide gases from the air. The most hydrophobic polymers containing the decafluorbiphenyl linker were suitable for benzene separation, while the best methane uptake values were 6.14 and 3.46 mg/g for DAB-Z-1O and DAB-A-1O, respectively. DAB-Z-1h, with the highest surface area and rich in nitrogen sites, exhibited the highest CO₂ uptake at 298 K (17.25).

G protein-coupled receptors (GPCRs) are amongst the most pharmaceutically relevant and well-studied protein targets, yet unanswered questions in the field leave significant gaps in our understanding of their nuanced structure and function. 3D pharmacophore models are powerful computational tools in silico drug discovery, presenting myriad opportunities for the integration of GPCR structural biology and cheminformatics. This review highlights success stories in the application of 3D pharmacophore modeling to de novo drug design, discovery of biased and allosteric ligands, scaffold hopping, QSAR analysis, hit-to-lead optimization, GPCR de-orphanization, mechanistic understanding of GPCR pharmacology and elucidation of ligand-receptor interactions. Furthermore, advances in the incorporation of dynamics and machine learning will be highlighted. The review will analyze challenges in the field of GPCR drug discovery, detailing how 3D pharmacophore modeling can be used to address them. Finally, we will present opportunities afforded by 3D pharmacophore modeling in the advancement of our understanding and targeting of GPCRs.

Micro lens arrays (MLAs) play a critical role in optical imaging, new energy technologies, and advanced displays. In this work, high-quality micro lens arrays with controllable profiles using femtosecond-laser-induced modification assisted wet etching (FLIM-WE) were fabricated. The effects of laser single-pulse energy, pulse number, and hydrofluoric acid etching duration on micro lens profiles were systematically studied. Optimization of these parameters enabled the successful preparation of dimensionally controlled micro lens arrays with stable performance and excellent surface quality on fused silica substrates. Ultimately, two types of micro lens arrays were fabricated using femtosecond laser-assisted wet etching. These arrays demonstrated exceptional uniformity and surface quality (Ra~100nm), facilitating clear imaging at various magnifications, with an adjustment range of 1.3X~3.0X. This provides a potential technical support for special micro-optical systems.

Microscale laser dynamic forming, as a novel high-speed microforming technique, can overcome the shortcomings of traditional microforming methods. However, in practical applications, laser dynamic microforming technology is often affected by the rebound behavior of the workpiece surface, limiting the further improvement of processing quality and efficiency. This paper aims to reduce the rebound effect in laser dynamic microforming by using multi-pulse laser shock loading. The forming results of workpieces under different laser energies and laser impact numbers were studied using experimental and numerical simulation methods. Numerical simulations of the forming results after multiple laser shocks were conducted using ANSYS/LS-DYNA software. These numerical simulation results were then experimentally validated and compared. Surface morphology and microstructure of the workpieces were characterized using a confocal microscope and scanning electron microscope, and energy dispersive spectroscopy (EDS) was used to analyze the chemical element content changes in the collision regions at the bottoms of the workpieces after multi-pulse loading, revealing the collision behavior patterns during the forming process. Finally, the forming laws of workpieces under multiple laser shocks were summarized.

This review examines additive manufacturing for refractory tungsten (W) and its alloys. It emphasizes the primary challenges and determining factors involved in additive manufacturing pure W, W alloys, and composites. Our focus in this regard extends to both process and alloying strategies designed to address critical issues such as densification, micro-cracking, and mechanical properties in tungsten-based components produced through additive techniques. Throughout the review, we organize existing knowledge and insights into convenient tables, serving as valuable resources for researchers embarking on a deeper exploration of these topics.

Accurately assessing forest structure and maintaining up-to-date information about forest structure is crucial for various forest planning efforts, including the development of reliable forest plans and assessments of the sustainable management of natural resources. Field measurements traditionally applied to acquire forest inventory information (e.g., basal area, tree volume, and aboveground biomass) are labor-intensive and time-consuming. To address this limitation, remote sensing tech-nology has been widely applied in modeling efforts to help estimate forest inventory information. Among various remotely sensed data, LiDAR can potentially help describe forest structure. This study was conducted to estimate and map forest inventory information across the Talladega Na-tional Forest by employing ALS-derived data and aerial photography. The quality of predictive models was evaluated to determine whether additional remotely sensed data can help improve forest structure estimates. Additionally, the quality of general predictive models was compared to that of species-group models. This study confirms that quality level 2 LiDAR data was sufficient for developing adequate predictive models (R2adj. ranging between 0.71 and 0.82) when compared to the predictive models based on LiDAR and aerial imagery. Additionally, this study suggests that species-group predictive models were of higher quality than general predictive models. Lastly, landscape-level maps were created from the predictive models, and these may be helpful to plan-ners, forest managers, and landowners in their management efforts.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

The number of diabetic patients worldwide is increasing rapidly. Prevention of diabetic reti-nopathy (DR), a leading cause of blindness, is a serious issue. We examined the effects of prophy-lactic pattern scanning laser retinal photocoagulation on DR development in 16 Spontaneously Diabetic Torii (SDT) fatty rats. Photocoagulation was applied to the right eyes of 8-week SDT fatty rats, and the left eyes served as the untreated controls. Electroretinography at 9 and 39 weeks of age and pathological examination of the retinal thickness and number of retinal folds, and immunohistochemistry of vascular endothelial growth factor and glial fibrillary acidic pro-tein at 24 and 40 weeks of age were performed bilaterally. No significant differences were seen between the left and right eyes in the apex latency and the amplitude of the oscillatory potential wave in the SDT fatty rats at 9 and 39 weeks of age and in the pathology and immunohistochem-istry in the SDT fatty rats at 24 and 40 weeks of age. Prophylactic pattern scanning retinal laser photocoagulation did not affect the development of DR in SDT fatty rats.