The reactive nature of traditional frequency stability methods can lead to delayed corrective actions and unnecessary loss-of-load. This work presents a distributed model predictive control method for proactive power system frequency stability. Dynamic state estimation model is derived through a particle filter. By being able to estimate the future state of frequency, corrective actions can be taken before the system reaches a critical condition. Proactive approach makes it possible to optimize the response to a disturbance, which results in a decrease of the amount of compensation utilized. The method is tested via Matlab simulations based on Kundur's Two-Area System, and the IEEE 14-Bus system. Performance metrics are provided and evaluated against other contemporary solutions found in literature. Easy-to-derive model, without hard-to-design parameters, indicate potential towards real-life applications.

Load Frequency Control (LFC) is essential to ensure the stability and performance of power systems. In this study, a novel optimization algorithm, the Sea Horse Optimizer (SHO) algorithm, was proposed for optimizing controller parameters in LFC problems of power system. The proposed SHO algorithm was tested on a two-area power system with photovoltaic system and reheat thermal units, under three different scenarios: a 10% load change in both area, large load disturbances, and varying solar radiation. The proposed algorithm optimizes the gain parameters of PI/PID controllers using performance metrics such as Integral of Absolute value of the Error (IAE), Integral of Square Error (ISE), Integral of Time multiplied by Square Error (ITSE), and Integral of Time multiplied by Absolute Error (ITAE). The study compared the performance of the SHO-optimized controller with other reported optimization algorithms such as Genetic Algorithm (GA), Firefly Algorithm (FA), Whale Optimization Algorithm (WOA), and Modified Whale Optimization Algorithm (MWOA). The study also evaluated the accuracy and effectiveness of the controllers using performance metrics such as Settling Time, Overshoot (M+), and Undershoot (M-). The results show that the SHO-tuned controller significantly reduces overshoot, undershoot, and settling time of the system oscillations compared to other algorithms. The study provides valuable insights into the optimization of LFC controllers and presents a significant contribution to the literature with its novel algorithm. The proposed SHO algorithm can be considered an effective alternative solution method for LFC in power systems.

Several studies have reported a relationship between autonomic dysfunction　 during tasks and Internet addiction. Changes within 24 h regarding heart rate variability (HRV) may be a more sensitive indicator than short term observations. We evaluated the influence of excessive Internet usage on HRV using a 24 h electrocardiogram (ECG) and examined acute changes during computer game tasks. A total 13 high school students and 22 young adults were recruited, and divided into excessive Internet user and non- excessive user groups based on Internet addiction test scores. The ECG was recorded continuously for 24 h by a wearable sensor and during two computer games (the Iowa gambling task and each participant’s preferred game) using a standard type ECG system. Multiple psychometric tests were also conducted. The excessive Internet user group exhibited clinically significant depressive symptoms, and higher self-reported scores for anxiety, impulsivity, autistic tendencies, and sleep problems than the non- excessive internet user group. There were weak differences within the 24 h high-frequency (HF) band power between two groups. During the Iowa gambling task, younger participants exhibited a reduced HF response, which may be related to weaker top- down self- regulatory mechanisms.

These days, numerous organizations and Analysis Centers (AC) offer various Ambiguity Resolution (AR) products using various methodologies. To use it for time-frequency transfer, there is no associated study. This paper chooses 16 MGEX stations with external high-precision atomic clocks to constitute 15 international time comparison links and uses AR products data from CNES, SGG, CODE, and PRIDE laboratory, using three ambiguity-fixed strategies, to thoroughly evaluate the effects of various strategies and AR products for high-precision time-frequency transfer. We reach the following results by using the IGS final clock product as a reference and comparing it to ambiguity-float. With various ambiguity-fixed procedures, the time stability STD of time transfer is increased for a single GPS, and the improvement ranges from 10% to 40%. The frequency stability has barely improved; up to 40%, the most notable improvement comes from FCB with GRM products. The time stability STD of combinations has improved after the addition of the Galileo system compared to the single GPS, and the improvement ranges from 2% to 9%. Most strategies have improved, while a few techniques have weakened with the GEC (GPS+Galileo+BDS) combination. We feel that the stability has not significantly increased with the system's increase within short-term stability after comparing multiple groups of linkages.

Evaluating the integrity of structures is an important issue in engineering applications. The use of vibration-based techniques has become a common approach to assessing cracks, which are the most often occurring damage in structural elements. When involving an inverse method, it is necessary to know the influence of the position and the geometry of the crack on the modal parameter changes. The geometry of the crack, both in size and shape, defines the damage severity (DS). In this study, we present a method (DS-SHC) used for estimating the DS for closed and open transverse cracks in beam-like structures by using the intact and damaged beam deflections under its weight and a Stochastic Hill Climbing (SHC) algorithm. After describing the procedure of applying DS-SHC, we calculate for a prismatic cantilever beam the severities for different crack types and depths. The results are tested by comparing the DS obtained with DS-SHC with those acquired from dynamic tests made using professional simulation software. We obtained a good fit between the severities determined in these two ways. Afterward, we performed laboratory experiments and find out that the severities obtained with the DS-SHC method can accurately predict the frequency changes due to the crack. Hence, these severities are a valuable tool for damage detection.

Objectives: This paper presents a statistical review of modelling simulations for frequency and sensitivity of COVID-19 testing paradigms. Methods: We performed a review of preprints and published articles on PubMed from January 1, 2020 – March 1, 2021 using the search terms “COVID screening testing”, “COVID testing frequency”, “COVID testing frequency screening” and “SARS-CoV-2 testing frequency”.Results: Several authors’ conclusions support the claim that test frequency and test sensitivity both play a role in reducing SARS-CoV-2 transmission. We highlight the interplay between frequency of testing, test sensitivity and the speed at which test results are available in our review. Conclusions: Evidence suggests that sensitivity and frequency of testing both play a part in decreasing transmission of disease. We conclude that, overall, test sensitivity plays less of a role in reducing disease transmission in a population compared to the frequency of testing and how quickly test results are available.

Frequency estimation of a single sinusoid in colored noise has received a considerable amount of attention in the research community. Taking into account the recent emergence and advances in compressive covariance sensing (CCS), the aim of this work is to combine the two disciplines by studying the effects of compressed measurements of a single sinusoid in moving-average (MA) colored noise on its frequency estimation accuracy. CCS techniques can recover the second-order statistics of the original uncompressed signal from the compressed measurements, thereby enabling correlation-based frequency estimation of single tones in colored noise using higher-order lags. Acceptable accuracy is achieved for moderate compression ratios and for a sufficiently large number of available compressed signal samples. It is expected that the proposed method would be advantageous in applications involving resource-limited systems such as wireless sensor networks.

Multiaxial fatigue experiments under asynchronous loadings with four different loading frequency ratios were carried out on 30CrMnSiA steel. The experimental results show that the fatigue life decreases when the axial or torsion frequency increases from 1 to 2, while there is no significant change when the axial or torsion frequency increases from 2 to 4. The surface crack paths are observed and show that cracks initiate on the maximum shear stress amplitude planes, propagate approximately tens of microns, and then turn to propagate along the maximum normal stress planes. The number of secondary cracks increases when the axial or torsion frequency increases. Subsequently, the Bannantine-Socie and Wang-Brown cycle counting methods along with various multiaxial fatigue criteria and Palmgren-Miner’s cumulative damage rule were used for fatigue life prediction. The experimental results are consistent with the fatigue life predicted by the Bannantine-Socie method with the section critical plane criterion for 30CrMnSiA steel under asynchronous loading paths.

In the context of seismic risk, studying the characteristics of urban soils and of the built environment means adopting a holistic vision of the city taking a step forward compared to the current microzonation approach. Based on this principle, CLARA WebGIS aims to collect, organise, and disseminate the available information on soils and buildings in the urban area of Matera. The geodatabase is populated with i) 488 downloadable geological, geotechnical, geophysical, surveys; ii) geological, geomorphological, and seismic homogeneous microzones maps and iii) a new Digital Surface Model. The CLARA WebGIS (https://smartcities-matera-clara.imaa.cnr.it/) is the first publicly available database reporting for the whole urban area the spatial distribution of the fundamental frequencies for soils and the overlying 4043 buildings, along with probability levels of soil-building resonance. The WebGIS is addressed to a broad target of end users (local government, engineers, and geologists, etc.) as a support to the implementation of seismic risk mitigation strategies in terms of urban planning, seismic retrofitting, and management of post-earthquake crises. We recommend that the database be managed by local administrators, who would also have the task of deciding on future developments and continuous updating as new data becomes available.

Time is a component quantity of various measurements and is also used on its own to sequence events, to compare the duration of events or the intervals between them, and to quantify rates of change of quantities in material reality or in the conscious experience [1]. The measuring equipment well might happen to be a clock. By making a presupposition that clock is Time, it is perceived experimentally that “Time exhibits wave-like properties”

Monitoring the dynamic responses of bridge structures has received considerable attention. It is important to synchronously measure both the quasi-static and dynamic displacements of bridge structures. However, the traditional accelerometer method cannot capture the quasi-static displacement component, although it can detect the dynamic displacement component. To this end, a novel composite instrument of a smartstation was proposed to monitor vibration displacements of footbridges. Full-scale experiments were conducted on a footbridge to validate the feasibility of the composite instrument-based monitoring method. A Chebyshev filter and wavelet algorithms were developed to process the composite instrument measurements. It was concluded that the measurement noise of the composite instrument was mainly distributed in a frequency range of 0–0.1 Hz. In two case studies with displacement peaks of 5.7–10.0 mm and 1.3– 2.5 mm, the composite instrument accurately identified the quasi-static and dynamic displacements. The composite instrument will be a potential tool for monitoring structural dynamics because of its enhanced overall performance.

This study presents a novel technique utilizing high frequency vibration to shorten treatment time and preserve alveolar bone in challenging orthodontic cases treated with Invisalign® clear aligners. Four non-growing orthodontic patients (age range 14-47 years old) with Class II skeletal patterns (convex profiles with retrognathic mandibles) who sought correction of their crowded teeth and non-surgical correction of their convex profiles were included in this study. These patients were treated using Invisalign clear aligners together with high frequency vibration (HFV) devices (120 Hz) (VPro5™) that were used by all patients for five minutes per day during active orthodontic treatment. Vertical control and forward rotation of the mandible for each patient was achieved through pre-programming the Invisalign to produce posterior teeth intrusion. Successful forward rotation of the mandibles achieved in all patients led to improvement of their facial convex profiles (ANB improved 2.1 + 0.5 degrees; FMA improved 1.2 +1.1 degrees). Dental decompensation was achieved by lingual tipping of the lower incisors and palatal root torque of upper incisors. The use of HFV together with Invisalign facilitated achieving these results within a 12+6 month period. In addition, more bone labial to the lower incisors after their lingual movement was noted. In conclusion, the use of HFV concurrent with SmartTrack Invisalign aligners allowed complex tooth movement and forward projection without surgery in non-growing patients with skeletal Class II relationships. The clinical impact and implications of this case series is that the use of HFV facilitates complex orthodontic tooth movement including posterior teeth intrusion and incisor decompensation in addition to increased bone formation labial to lower incisors that may minimize future gum recession due to their labial inclination.

This study proposes a novel flexible bus dispatching system where a fleet of fully automated modular bus units, together with conventional buses, serves the passenger demand. These modular bus units can either operate individually or combined (forming larger modular buses with a higher passenger capacity). This provides enormous flexibility to manage the service frequencies and vehicle allocation, reducing thereby the operating cost and improving passenger mobility. We develop an optimization model used to determine the optimal composition of bus units and the optimal service frequency at which the buses (both conventional and modular) are dispatched across each bus line. We explicitly account for the dynamics of traffic congestion and complex interactions between the modes at the network level based on the recently proposed three-dimensional macroscopic fundamental diagram (3D-MFD). To the best of our knowledge, this is the first application of the 3D-MFD and modular bus units for the frequency setting problem in the domain of bus operations. Numerical results show the improvements in the total system cost made by adapting the number of combined modular bus units and their dispatched frequencies to the evolution of both, the car and the passenger demand. A comparison with the commonly used approach that considers only the bus system (neglecting the complex multimodal interactions and congestion propagation) reveals the value of the proposed modeling framework.

High-frequency near-infrared diode laser provides high peak output, low heat accumulation, and efficient biostimulation. Although these characteristics are considered suitable for osteoarthritis (OA) treatment, the effect of high-frequency near-infrared diode laser in in vitro or in vivo OA models has not yet been reported. Therefore, we aimed to assess the biological effects of high-frequency near-infrared diode laser irradiation on IL-1β-induced chondrocyte inflammation in an in vitro OA model. Normal Human Articular Chondrocyte-Knee (NHAC-Kn) cells were stimulated with human recombinant IL-1β and irradiated with high-frequency near-infrared diode laser (910 nm, 4 or 8 J/cm2). The mRNA and protein expression of relevant inflammation- and cartilage destruction-related proteins was analyzed. IL-1β treatment significantly increased the mRNA levels of IL-1β, IL-6, TNF-α, MMP-1, MMP-3, and MMP-13. High-frequency near-infrared diode laser irradiation significantly reduced the IL-1β-induced expression of IL-1β, IL-6, TNF-α, MMP-1, and MMP-3. Similarly, high-frequency near-infrared diode laser irradiation decreased the IL-1β-induced increase in protein expression and secreted levels of MMP-1 and MMP-3. These results highlight the therapeutic potential of high-frequency near-infrared diode laser in OA.

Recent experimental research has shown that mass is linked to Compton periodicity. We suggest a new way to look at mass: Namely that mass at its most fundamental level can simply be seen as reduced Compton frequency over the Planck time. In this way, surprisingly, neither the Planck constant nor Newton's gravitational constant are needed to observe the Planck length, nor in any type of calculation or gravitational predictions. The Planck constant is only needed when we want to convert back to the more traditional and we would say arbitrary mass measures such as kg. The theory gives the same predictions as Einstein's special relativity theory, with one very important exception: anything with mass must have a maximum velocity that is a function of the Planck length and the reduced Compton wavelength. For all observed subatomic particles, such as the electron, this velocity is considerably above what is achieved in particle accelerators, but always below the speed of light. This removes a series of infinity challenges in physics. The theory also offers a way to look at a new type of quantum probabilities. As we will show, a long series of equations become simplied in this way. Further Newton's gravitational constant G is clearly not needed for gravity calculations or predictions; it is the Planck length and the speed of light (gravity) that are essential for gravity, and both can be measured easily with no knowledge of G.

Dynamic mechanical analysis (DMA) is a versatile technique that complements the information given by the more traditional thermal analysis techniques such as differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and thermal mechanical analysis (TMA). Dynamic constants such as storage modulus, loss modulus, and loss factor are temperature dependent and provide information about interfacial bonding between reinforced fibre and polymer matrix of composite material. To study the above mentioned properties at the glass transition region, for unidirectional fibrous composites reinforced with continuous fibers a reliable model was applied. In particular, the composite material was considered as composed of three phases with the intermediate phase between matrix and fibres, the interphase, to have variable properties depending on those of main phases and the mode of preparation of the overall material. The glass transition temperature is defined as the point at which the specific volume versus temperature curve changes abruptly slope marking the region between rubbery polymer and glassy polymer nature. Hence, the behaviour of unidirectional fibrous composites was investigated at this region. Examination of the glass transition temperature, which constitutes an upper limit for the structurally important glassy region through the loss factor, was performed by its consideration as a combination of glass transition temperature of matrix and interphase.

The finding of important explanatory variables for the location parameter and the scale parameter of the generalized extreme value (GEV) distribution, when the latter is used for the modelling of annual streamflow maxima, is known to have reduced the uncertainties in inferences, as estimated through regional flood frequency analysis frameworks. However, important explanatory variables have not been found for the GEV shape parameter, despite its critical significance, which stems from the fact that it determines the behaviour of the upper tail of the distribution. Here we examine the nature of the shape parameter by revealing its relationships with basin attributes. We use a dataset that comprises information about daily streamflow and forcing, climatic indices, topographic, land cover, soil and geological characteristics of 591 basins with minimal human influence in the contiguous United States. We propose a framework that uses random forests and linear models to find (a) important predictor variables of the shape parameter and (b) an interpretable model with high predictive performance. The process of study comprises of assessing the predictive performance of the models, selecting a parsimonious predicting model and interpreting the results in an ad-hoc manner. The findings suggest that the shape parameter mostly depends on climatic indices, while the selected prediction model results in more than 20% higher accuracy in terms of RMSE compared to a naïve approach. The implications are important, since incorporating the regression model into regional flood frequency analysis frameworks can considerably reduce the predictive uncertainties.

We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

Resistive patch array incorporating with metallic backplane provided an effective way to the achievement of broadband metamaterial absorbers(MAs). When loading metallic metamaterial to resistive MA, the outstanding construction helps realize more flexible and diversified forms of broadband absorption. In this paper, we attempted to load metallic resonators(MRs) to resistive MA in the three-dimensional construction, which benefits further enhancement of lower-frequency absorption. Simulation showed that the partial absorption band was separated to lower frequency, while the rest of broadband absorption was unaffected. Meanwhile, after combining multi-unit of the proposed MAs, the stair-stepping broadband absorption was also achieved. At last, three samples were fabricated. The agreements between simulations and experimental results demonstrated that resistive MA loaded with MRs provided an effective way for further enhancement of lower-frequency absorption with almost no change of the absorbing structure and areal density. Thus, it is worthy to expect a wide range of applications to emerge inspired from the proposed attempt.

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1,600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1,600 kHz to within 0.05 mm (2s) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

Abstract: Epidemiological, experimental, and ecological data have indicated the controversial effect of in utero chronic low dose rate (100 mGy) dose radiation exposure. Our main goal of this study was to examine if different low dose rates of chronic pre- or/and post-natal radiation exposure with accumulative high doses could induce hippocampal cellular, mRNA, and miRNA changes leading to neuropsychiatric disorders. The comprehensive mouse phenotypic traits, organ weight pathological, blood mRNA and miRNA changes were also studied. Using different approaches including SmithKline, Harwell, Imperial College, Royal Hospital, Phenotype Assessment (SHIRPA), neurobehavioral tests, pathological examination, immunohistochemistry, mRNA and miRNA sequencing, and real-time quantitative polymerase chain reaction ( qRT-PCR) validation, we found that in prenatally irradiated (100 mGy/d for 18 days with an accumulative dose of 1.8 Gy) 1-year-old mice, no cellular changes including neurogenesis, mature neurons and glial cells in the hilus of the dentate gyrus and development of cognitive impairment, neuropsychiatric disorders occurred. However, a significant reduction in body weight and mass index (BMI) was indicated by the SHIRPA test. A reduced exploratory behavior was shown by an open field test. Organ weight measurement showed a significant reduction of the testes, kidneys, heart, liver, and epididymides although no abnormal changes from pathological examination. mRNA and miRNA sequencing and qRT-PCR validation revealed the upregulation of Rubcnl, Abhd14b and downregulation of Hspa1b, P4ha1, and Banp genes in both hippocampus and blood of mice prenatally irradiated with 100 mGy/d. Meanwhile, downregulation of miR-448-3p, miR1298-5p in the hippocampus, miR-320-3p, miR-423-5p, miR-486b-5p, miR-486b-3p, miR-423-3p, miR-652-3p, miR-324-3p, miR-181b-5p, miR-let-7b and miR-6904-5p in the blood was induced. The target scan revealed that Rubcnl is one of the miR-181b-5p targets in the blood. We, therefore, concluded that prenatal chronic irradiation with a low dose rate of 100 mGy/d and accumulative dose of 1.8Gy or below may not induce significant adverse health effects on the offspring. Further study of different low dose rate radiation exposure with accumulative high doses may provide threshold doses for authorities or regulators to set new radiation safety guidelines to replace those extrapolated from acute high dose/dose rate irradiation to reduce unnecessary emergency evacuation or expanding once a nuclear accident or leakage occurs.

The limited supply of drinking water has aroused people's curiosity in recent decades. Adsorption is a popular method for removing hazardous substances from wastewater, especially heavy metals, as it is cheap, highly efficient and easy to use. In this work, a new sludge-based activated carbon adsorbent (SBAC1 / SBAC2) was developed to remove hazardous metals such as cadmium (Cd+2) and lead (Pb+2) from an aqueous solution. The chemical structure and surface morphology of the produced SBAC1 and SBAC2 were investigated using a range of analytical tools such as CHNS, BET, FT-IR, XRD, XRF, SEM, TEM, N2 adsorption/desorption isothermal and zeta potential. BET surface areas were examined and SBAC2 was found to have a larger BET surface area (498.386 m2/g) than SBAC1 (336.339 m2/g). SBAC2 had a lower VBJH (1.5026 cm3 g-1) than SBAC1 (1.59873 cm3 g-1), but a higher VT (0.3748 cm3 g-1) than SBAC1 (0.2688 cm3 g-1), while the average pore size was 10-100 nm for SBAC1 and 45-50 nm for SBAC2. The ideal conditions investigated for the removal of Pb+2 and Cd+2 were 10 mg SBAC1 / SBAC2, Pb+2 / Cd+2 at an starting concentration of 30 mg/L, a temperature of 40 and 50 °C, pH = 6, 8 and contact times of 10 and 15 minutes for Pb+2 and Cd+2, respectively. SBAC1 and SBAC2 eliminated approximately 99.99% of Cd+2 and Pb+2 out the water under all conditions tested. The results of the adsorption of Cd+2 and Pb+2 were in good agreement with the pseudo-second-order equation (R2 = 1.00). Under the experimental conditions, the Cd+2 and Pb+2 adsorption equilibrium data were effectively linked to the Langmuir and Freundlich equations for SBAC1 and SBAC2, respectively. Langmuir model calculated the adsorption capacities of SBAC1 and SBAC2 for Cd+2 (309.24 and 329.62 mg/g) and for Pb+2 (318.46 and 339.61 mg/g), respectively. The regeneration showed high recyclability for the fabricated SBAC1 and SBAC2 during five consecutive reuse cycles. As a result, the produced SBAC1 and SBAC2 are attractive adsorbent for the elimination of heavy metals from various environmental and industrial wastewater samples.

Background: Alarming data indicates that low back pain (LBP) affected around 619 million people globally in 2020, that presenting significant health and economic burden. Importantly, the chronic LBP (cLBP) strongly impairs quality of life and leads to disability and premature retirement thus emphasizing the urgent need for providing deeper insight into the factors that affect treatment outcomes and offer thorough guidance for the assessment and management of this disease. Taking into consideration the rising prevalence of cLBP and knowledge gap referring to the overall health benefits of balneotherapy (BT), the aim of this study was to assess the effects of BT on functional status, quality of life and psychological symptoms in patients with cLBP. Methods: A total 210 patients were recruited and divided into two groups: patients receiving conventional pharmacological therapy (CT) and receiving BT. The effectiveness of the treatment was assessed on the basis of Visual Analog Scale for pain intensity, EuroQol (EQ-5D) for the patient’s self-rated health and Work Ability Index Questionnaire to evaluate functional ability. In order to provide deeper insight into the quality of life and also factors associated with the functional status and mental health affected by BT, we also used the Short Form Health Survey Questionnaire and Center of Epidemiologic Studies Depression Scale. Results: Our findings suggest that BT significantly contributed to reduction of pain, better functionality and disability perception status. Conclusions: Understanding the association between individual perceptions of functionality, emotional and social elements provides basis for providing comprehensive guidelines and recommendations for cLBP management.

Background Gliomas are the most prevalent primary malignant brain tumors worldwide. Recent studies highlight the potential of long non-coding RNAs (lncRNAs) in tumor progression, with LINC01354 being upregulated in various malignancies. This study investigates the role of LINC01354 in glioma prognosis to provide novel insights for early prognosis prediction.Methods This study involved four cohorts of low-grade glioma tissue samples collected from hospitals in Xinjiang, Beijing, and Guangzhou, China. Quantitative Real-Time Polymerase Chain Reaction (qRT-PCR) was used to measure LINC01354 expression levels. Clinical information and survival data were analyzed using Cox regression and ROC analysis to evaluate the association between LINC01354 expression and overall survival. Clinical comparisons were conducted to identify potential discrepancies in clinical parameters across different cohorts.Results Elevated LINC01354 levels were associated with poorer overall survival in the West China cohort (Xinjiang) but not in the North (Beijing) or South China (Guangzhou) cohorts. Clinical parameter comparisons revealed no significant differences among the cohorts that could explain the regional discrepancy. Further analysis within the West China cohort indicated that LINC01354's prognostic value was consistent across Han and non-Han ethnic groups and unaffected by dietary staples. However, LINC01354's prognostic significance was more pronounced in patients born in Xinjiang compared to those born elsewhere. A prognostic model incorporating LINC01354 expression and birth location demonstrated good predictive accuracy with ROC AUC values of 0.777 in the training cohort and 0.757 in the validation cohort.Conclusion LINC01354 is a potential prognostic biomarker for low-grade glioma in the West China population, particularly among patients born in Xinjiang.

In this paper, different concepts of reconfigurable RF-MEMS attenuators for beamforming applications are proposed and critically assessed. Capitalizing on the previous part of this work, the 1-bit attenuation modules featuring series and shunt resistors and low-voltage membranes (7-9 V) are employed to develop a 3-bit attenuator for fine-tuning attenuations (&lt; -10 dB) in the 24.25-27.5 GHz range. More substantial attenuation levels are investigated by means of fabricated samples of coplanar waveguide (CPW) sections equipped with Pi-shaped resistors aiming at attenuations of -15, -30, and -45 dB. The remarkable electrical features of such configurations, showing flat attenuation curves and limited return losses, and the investigation of a switched-line attenuator design based on them led to the final proposed concept of a low-voltage 24-state attenuator. Such simulated device combines the Pi-shaped resistors for substantial attenuations with the 3-bit design for fine-tuning operations, showing a maximum attenuation level of nearly -50 dB while maintaining steadily flat attenuation levels and limited return losses (< -11 dB) along the frequency band of interest.

Background: Nephrolithiasis, or kidney stone disease, presents a significant global health burden, with incidence rates and treatment practices varying widely globally. This study aims to discuss the epidemiology, risk factors, treatment modalities, and challenges for nephrolithiasis in the lower half of the World Bank Rank; low and lower-middle-income countries. Methods: A comprehensive literature review was conducted using PubMed for each country on the list, focusing on studies published from January 2000 onwards and reporting data on prevalence, risk factors, treatment practices, and economic implications. Results: Nephrolithiasis represents a significant burden for healthcare systems, with noteworthy geographical variability in prevalence possibly dependent on socioeconomic status and gender. Risk factors include dietary habits, climate, pollution, and infectious diseases. Treatment practices in some regions still rely on open surgery due to limited access to advanced endourological techniques, while other regions demonstrate high proactivity in research. The burden is exacerbated by inadequate healthcare infrastructure and training. Conclusions: Addressing nephrolithiasis in challenging economic circumstances requires targeted interventions, including improved access to modern treatment methods, enhanced training for healthcare professionals, and better socioeconomic and environmental conditions. Future research should focus on region-specific strategies and the development of sustainable healthcare solutions.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

The built environment sector’s growing impact on climate change is becoming increasingly important due to its share in energy consumption and greenhouse gas emissions. Global efforts have been undertaken to design and develop residential dwellings that aim towards zero energy and carbon emission, but there remains a multitude of obstructions to efficient construction processes. This study is focused on the gaps and barriers that have emerged during the pre-construction phase of a low-environmental-impact Passive House in Fayetteville, Arkansas. The technical, management, regulatory, and supply chain obstacles to the construction of a new three-story residential Passive House are documented to engage knowledge transformation in the design and construction of sustainable buildings of interest to developers and property owners. Primary data are collected by direct observation as well as open-ended interviews and secondary data collected through a literature review to understand the barriers and gaps faced by different key actors during the pre-construction phase in different regions. This local study highlighted the lack of interest, knowledge, and experience in sustainable building design among professionals having a significant influence on the project goals and timeline and was mentioned by participants as a common barrier as well as the inconsistency and inadequacy of regulatory framework of existing building codes to implement sustainable building design. These barriers along with other identified barriers are discussed and recommendations to overcome these barriers are provided.

This paper describes different variants of broadband and simple attenuator modules for beamforming applications, based on Radio Frequency Micro Electro-Mechanical Systems (RF-MEMS), framed within Coplanar Waveguide (CPW) structures. The modules proposed in the first part of this work differ in their actuation voltage, topology, and desired attenuation level. Fabricated samples of basic 1-bit attenuation modules, characterized by a moderate footprint of 690 x 1960 µm2 and aiming at attenuation levels of -2, -3 and -5 dB in the 24.25-27.5 GHz range, are presented in their variants featuring both low actuation voltages (5-7 V) as well as higher values (~ 45V), the latter ones ensuring larger mechanical restoring force (and robustness against stiction). Beyond the fabrication non-idealities that affected the described samples, the substantial agreement between simulations and measurement outcomes proved that the proposed designs could provide precise attenuation levels up to 40 GHz, ranging up to nearly -3 dB and -5 dB for the series and shunt variants, respectively. Moreover, they could be effective building blocks for future wideband and reconfigurable RF-MEMS attenuators. In fact, in the second part of this work, combinations of the discussed cells and other configurations meant for larger attenuation levels will be investigated.

Climate change has become a global nightmare, and the awareness of the causes of carbon emissions have resulted in rigorous studies. These studies linked the increase in global warming with booming economic growth. Since global warming has become more apparent, researchers have explored ways to decouple economic activities from carbon growth. Economic and carbon growth must be decoupled to achieve a low-carbon economy to support the carbon growth plan or emission reduction strategy. The world is transitioning towards a carbon-neutral and green ecosystem, so finding ways to decouple carbon emissions from economic activities is an exciting topic to explore. The study reviews current information on the importance of decoupling energy from economic growth innovative techniques that thoroughly examine the challenges and constraints of low-carbon energy systems. This review revealed that decarbonization and dematerialization had been achieved without declining global economic growth. It also provides information on energy use and economic activities leading to global carbon emissions and alternative solutions to the global challenge of climate change. The decoupling methods commonly used to determine the impact of energy decarbonization on economic growth are explored. All suggested that economic growth is a primary mover of global carbon emission increase and must be separated to achieve a carbon environment.

The COVID-19 pandemic halted progress in global vaccine coverage and disrupted routine childhood vaccination practices worldwide. While there is ample evidence of vaccination declines experienced during the pandemic, it is less clear how low-income countries were affected. We executed a systematic review to synthesize the current literature on impacts to routine childhood vaccinations in low-income countries from January 1, 2020 to February 8, 2023. We collected data using an extraction form on Covidence and assessed the quality of studies included in the review using the Risk of Bias in Non-Randomized Studies of Interventions (ROBINS-I) tool. Effect estimates for changes in vaccination during the pandemic were reported and summarized. Factors that influenced changes were grouped into descriptive themes. Thirteen studies, encompassing 18 low-income countries and evaluating 15 vaccines at varying doses, were included in the final review. We found that routine childhood vaccinations during the COVID-19 pandemic varied considerably by vaccine type, location, and phase of the pandemic. Nine different themes were identified as factors that influenced changes in vaccination. Documenting past experiences and lessons learned is crucial for informing preparedness efforts in anticipation of future public health emergencies. Failure to effectively address these things in the next public health emergency could result in a recurrence of declining routine childhood vaccinations.

Abstract: Efforts for carbon emission reduction have been identified as a major climate change mitigation target in the Paris Agreement. The 26th Conference of Parties to the United Nations Framework Convention on Climate Change highlighted the worldwide effort for cleaner and greener mining, urging the mineral industry to embrace greener operational emissions reduction technologies and strategies. Ghana pledged at the Paris Conference to reduce CO2 emissions by 15% and increase renewable energy share to 10% of the national energy mix. Here the fundamental question is how Ghana’s mining industry can contribute to CO2 emission reduction efforts. This paper investigates barriers to low-carbon emission policy implementation among mining companies in Ghana. The questionnaire survey was conducted among Ghana’s four large-scale gold mining companies. As the sample number of available companies is limited, we used a descriptive analysis to assess the responses. The results show that the companies expressed widely different ways to respond to the issues of cost, a government policy/regulations for carbon emission reduction, and the adoption/acquisition of low-carbon technologies. Those companies that are relatively less prepared for this endeavor emphasized the uncertainties of securing sufficient energy in case of using low-carbon technologies. They also expressed a need for more trained workers to handle low-carbon technologies. All companies agreed with a expected high cost of adopting low-carbon options. There was a communication gap with the relevant government ministry about low-carbon mining options where the government should be able to facilitate the involvement of othe low technology providers, such as solar PV installation.

Amidst escalating environmental concerns, short natural fiber thermoplastic (SNFT) biocomposites have emerged as sustainable materials for the eco-friendly production of mechanical components. However, their limited durability has prompted research into the experimental evaluation of the deterioration of the mechanical characteristics of SNFT biocomposites, particularly under the influence of ultraviolet rays. However, conducting tests to evaluate the mechanical properties can be time-consuming and expensive. In this study, an artificial neural network (ANN) model was employed to predict the mechanical properties (tensile strength) and the impact performance (resistance and absorbed energy) of polypropylene reinforced with 30 wt.% short flax or wood pine fibers (referred to as PP30-F or PP30-P, respectively). Eight parameters were collected from experimental studies. The ANN input parameters comprised nondestructive test results, including mass, hardness, roughness, and natural frequencies, while the output parameters were the tensile strength, the maximum impact load and absorbed energy. The model was developed using the ANN toolbox in MATLAB. The linear coefficient of correlation and mean squared error were selected as the metrics for evaluating the performance function and accuracy of the ANN model. They calculate the relationship and the average squared difference between the predicted and actual values. The data analysis conducted by the models demonstrated exceptional predictive capability, achieving an accuracy rate exceeding 96%, which was deemed satisfactory. For both the PP30-F and PP30-P biocomposites, the ANN predictions deviated from the experimental data by 3, 5, and 6% about the impact load, absorbed energy, and tensile strength, respectively.

Low-cost monitors have made possible for the first time measurements of long-term (months to years) potential indoor exposures to fine particles. Indoor and outdoor measurements made over nearly 5 years (2017-2021) by the largest network of low-cost monitors in the United States (PurpleAir) are compared to the prevalence of adult smokers in 1650 Zip codes within the three West Coast states of California, Oregon, and Washington. The results show that mean indoor exposures above the 75th percentile of adult smoking prevalence are more than 50% higher than those below the 25th percentile. Mean outdoor concentrations are also elevated, but by a smaller amount (20%). Both comparisons are significant at the p&lt;0.001 level. The elevation of the PM2.5 concentrations with increasing smoking prevalence is evidence of environmental disparities in income, education, and other socioeconomic indices..

Background and objectives: Musculoskeletal (MSK) pain significantly impacts physical activity and quality of life in the elderly, potentially influencing mortality. This study explored the relationship between MSK pain, physical activity, muscle mass, and mortality among older adults. Material and Methods: We studied 1000 participants of the Korean Longitudinal Study on Health and Aging (KLoSHA), a prospective, population-based cohort study of people aged 65 years or older. Survival status was tracked over a 5-year period. Correlations between Low back pain (LBP), knee pain, regular exercise, appendicular skeletal muscle mass (ASM), and other variables were analyzed. Logistic regression analyzes were used to identify independent risk factors for mortality. Results: Of the total participants, 829 (82.9%) survived after a 5-year period. Survivors tended to be younger, had a higher BMI, and were more active in regular exercise. In contrast, non-survivors exhibited a higher prevalence of both LBP and knee pain, along with increased instances of multiple MSK pain. Lower ASM correlated moderately with LBP and knee pain, whereas higher ASM was associated with regular exercise Lower ASM was moderately associated with LBP and knee pain, while higher ASM correlated with engagement in regular exercise. There was a moderate correlation between LBP and knee pain, both of which were associated with a lack of regular exercise. Age, sex, ASM, and regular exercise were significant predictors, even though MSK pain itself did not directly predict all-cause mortality. Conclusions: This study demonstrated the independent association between ASM, regular exercise, and mortality. Although MSK pain did not directly correlate with all-cause mortality, the non-survivor group had higher levels of both single and multiple MSK pain. Recognizing the interplay of MSK pain, physical activity, and muscle mass for older adults, the research underscores the need for holistic strategies to enhance health outcomes in older individuals with MSK pain.

Through long-term Rayleigh lidar observations during 2010-2022, atmospheric gravity wave (AGW) activities in the middle atmosphere (30–65 km) are statistically investigated at Haikou (110.3°E, 19.9°N) in China. In total, 827 quasi-monochromatic AGW events are identified from the lidar dataset, and the vertical wavelength, observed wave period, and vertical propagation direction of dominant waves are extracted for each AGW event by analyzing the power spectra of wave-induced temperature perturbations. It is revealed that 81.7% of all AGW events were associated with upward-propagating waves, and the proportion of upward-propagating AGWs reached a maximum in autumn and a minimum in winter. The most common vertical wavelengths and wave periods were 6–11 km and 4–10 hours, respectively. In particular, 68 AGW events associated with simultaneous upward and downward propagating waves were observed by lidar, corresponding to 8.2% of the events. The occurrence of such special AGW phenomena is qualitatively discussed, and multiple formation mechanisms may exist. Comparisons are made with previously reported lidar observation results, and the statistical features of AGW activity in the low-latitude middle atmosphere may vary over a relatively wide range depending on the location and altitude. However, a majority of AGWs propagate upward in the middle atmosphere.

Understanding the evolution patterns in patients diagnosed with acute myeloid leukemia (AML) after therapy is relevant due to the dismal outcome still present in refractory or relapsed AML patients. We performed a retrospective, single-center study to evaluate the mutation profile in paired samples obtained at the time of diagnosis and at the onset of progressive or refractory disease in patients diagnosed with AML through a commercial next-generation sequencing (NGS) panel. In total, 62 patients were analyzed. Of these, 28 patients received ICT, and 34 patients underwent low-intensity treatments. In LIT patients, there were emergent mutations at progressive disease in a 64% (22/34) of the patients. Emergent mutations in the RAS-MAPK signaling pathway were observed in 35.9% (12/34) , corresponding to 54.5% of all patients with emergent mutations (12/22). These were found in 12/22 patients that received venetoclax in combination with hypomethylating agents. Six presented mutations in genes related to the RAS-MAPK pathway. Emerging mutations are frequently observed at progressive AML disease after therapy. In patients treated with LIT, mutations in RAS-MAPK signaling pathway might have a key role on the secondary clinical resistance, not only if they are present at diagnosis, becoming a potential target for the development of new drugs.

The airflow carried by artificial aeration provides oxidant O2 for microbial growth and mineral dissolution in heap bioleaching. To investigate the effect of forced aeration rate on bioleaching of low-grade copper sulfide ores, column bioleaching experiments with six columns were conducted in the aeration range of 0~150 L/h at 30~45 ℃. The results showed that when the aeration rate was higher than 95 L/h, the proportions of heap settlement and fine particles mass were much greater than that without aeration. The final total Fe concentration and bacterial cell numbers in pregnant leach solution increased with the increase of aeration rate.The final concentrations of Cu2 + in the mother liquor under aeration conditions of 60-150 L / h were 1.411, 1.432, 1.498, 1.491 and 1.583 g / L, respectively, which were higher than 1.345 g / L under non-aeration conditions. When the aeration rate was 150 L / h, the final Cu leaching rate was 80.1 %, which was 11.4 % higher than that without aeration ( 68.7 % ). Furthermore, in the early stage of leaching, copper leaching rate with 95 L/h aeration rate remained the highest. 结论Artificial aeration accelerates the bioleaching of low-grade copper sulfide ores by improving porosity structure, temperature range of bacterial activity and microbial catalyzed dissolution of targeted minerals.

Background: Very low-calorie ketogenic diet (VLCKD) is associated with improvement of metabolic and cardiovascular disorders. We aimed to evaluate the effects of VLCKD in patients with Cushing’s disease (CD) as adjunctive therapy to treatment for primary disease. Methods: We evaluated clinical, hormonal and metabolic parameters in 15 patients with CD and 15 controls at baseline and after 1 week and 3 weeks of VLCKD and further 2 weeks of low-carbohydrate ketogenic diet (LCKD). Results: After 5 weeks of diet a significant decrease in BMI (p=0.002), waist circumference (WC) (p=0.024), systolic (p=0.015) and diastolic blood pressure (p=0.005), ACTH (p=0.026), cortisone (p=0.025), total (p=0.006) and LDL cholesterol (p=0.017), triglycerides (p=0.016), alkaline phosphatase (p=0.008) and a significant increase in HDL cholesterol (p=0.017), vitamin D (p=0.015) and oral disposition index (Dio)(p=0.004) was observed in CD. A significant decrease in BMI (p=0.003), WC (p=0.002), systolic (p=0.025) and diastolic (p=0.007) blood pressure and total cholesterol (p=0.026) and increase in HDL cholesterol (p=0.001) and DIo (p&lt;0.001) was observed in controls. Conclusions: The current study confirms that ketogenic diet is effective in improving metabolic disorders and shows that a nutritional approach may be combined with conventional CD therapy in order to improve metabolic and cardiovascular comorbidities.

FeZnNa@SiO2-C catalyst with graphitized carbon (GC) modified mesoporous SiO2 support metal nanoparticles was prepared by sol-gel method. The effect of adding metal Na and Zn promoters as a dispersion on the CO2 hydrogenation to low olefins was systematically studied. The results showed that Zn-Na, as a combination, promoted the absorption of CO2 and improved the conversion rate of CO2. Na as an alkaline substance can improve the absorption of more acidic CO2, improving the conversion rate of CO2 to 59.03%. Meanwhiles, addition of secondary metal Zn into Fe-based catalysts to form a surface alloy could alter the adsorption of CO2 and the activation of C-O bonds, inhibit the subsequent hydrogenation of olefins to paraffins, facilitate the reduction of Fe2O3 and the formation of active Fe5C2 species. From TEM and XRD, the formation of active Fe5C2 species was found, the selectivity of the target product was 41.07%. The deep hydrogenation of olefins is inhibited, by inhibiting their deep hydrogenations, the STY of C2=-C4= was raised again, up to 0.0436. However, the corresponding STY does not increase infinitely with the increase of Na content, and when the Na content to 6.4%, which can be shown higher CO2 hydrogenation catalytic performance. Compared with Fe@SiO2-C catalyst, Na and Zn promoted Fe-based catalysts prepared by modified sol-gel method, can be used directly for highly efficient CO2 hydrogenation to low olefins and thus will be more promising in the future.

Background: Spinal pain is highly prevalent and in Spain it produces a very high economic cost and the scientific evidence supporting treatments shows low to moderate evidence for exercise. Therefore, the aim of this study was to assess the effectiveness of a therapeutic group exercise protocol in reducing pain intensity and disability in patients with spinal pain in primary health care setting. Methods: A total sample of 149 patients who suffered from chronic non-specific spinal pain. Patients received a therapeutic exercise protocol, including exercises of auto-mobilization of the neck and lumbar regions, as well as core stabilization exercises. Pain intensity and disability were evaluated before and after the therapeutic exercise protocol. Results: Statistically significant differences (P&lt;0.05) were shown for pain intensity and disability of patients with neck and low back pain with an effect size from moderate to large. Conclusions: A therapeutic exercise protocol may provide beneficial effects on disability and pain intensity in patients with chronic non-specific spinal pain, including neck and low back pain conditions. Clinicians should consider the use of self-administered exercise protocols, demonstrate great effectiveness, and be less costly.

The increase and diversity of low-cost Air Quality (AQ) sensors, as well as their flexibility and low power consumption, offers us the opportunity to integrate them into a broad AQ wireless sensor networks with the aim of enabling real-time monitoring and higher spatial sampling density of pollution in all parts of the cities. Considering that the vast majority of the population lives in these cities and the increase in respiratory/allergic problems in a large part of the population, it is of great interest to offer services and applications to improve their quality of life. In the ECO4RUPA project we focus on this kind of service, proposing an inclusive and intelligent routing ecosystem carried out by using a network of low-cost AQ sensors with the support of 5G communications along with official AQ monitoring stations, assisted with artificial intelligence to improve the AQ monitoring data and by spatial interpolation techniques to enhance its spatial resolution. The goal of this service is to calculate healthy walking and/or cycling routes according to the particular citizen’s profile and needs. We provide and analyse the results of the proposed route planner under different scenarios (different time tables, congestion road traffic and routes) and different user’s profiles, with special interest on citizens with asthma and pregnant women, since both require special needs. In summary, our approach can lead to an approximately average reduction in pollution exposure of 17.82%, while experiencing an approximately average increase in distance travelled of 9.8 %.

(1) Background: This study aimed to evaluate whether the implementation of a modified blood sampling protocol, which focused on need-based laboratory testing and minimized venous sampling by replacing it with point-of-care testing (POCT) via capillary puncture, successfully reduced iatrogenic blood loss, incidence of anemia, and frequency of blood transfusion in extremely low birth weight infants (ELBWIs) without negatively affecting neonatal outcomes. (2) Methods: A retrospective analysis was conducted on 313 ELBWIs of gestational age (GA) between 23 and 28 weeks, born between 2013 and 2019. The infants were divided into two groups: before (period I) and after (period II) the implementation of the modified blood sampling protocol in January 2016. Propensity score matching was conducted to minimize selection bias. Clinical data, including the frequency and amount of blood sampling, frequency and volume of blood transfusion, and clinical characteristics, such as gestational age, birth weight, and neonatal outcome data, were collected and compared between the two groups. (3) Results: No significant differences in the GA or birth weight between the two periods were observed. The total sampling volume during a month after birth (16.7 ± 4.1 mL vs. 15.6 ± 4.4 mL, P=0.03) and total sampling volume during hospital days (51.4 ± 29.7 mL vs. 44.3 ± 27.5 mL, P=0.04) in period II were significantly lower than that in period I. There were no differences in the mortality or morbidity between the two periods. Although the transfusion frequency and amount did not have significant differences between the periods, we observed a positive correlation between the transfusion frequency and sampling volume (coefficient: 0.09, 95% CI: 0.08–0.11). (4) Conclusions: The modified blood sampling protocol effectively reduced the iatrogenic blood loss without negatively affecting the neonatal outcomes.

Chondrosarcoma, represents approximately 0.1% of all neoplasms of the head and neck, being considered a rare disease, but with a relatively good prognosis. The 5-year overall survival (OS) rate is estimated at 70-80%, being considered a disease with a low growth rate. About 13% of all cases of chondrosarcoma, are located in the region of the head and neck. We present the case of a young patient treated multimodally, lost from the oncological records less than two years after the diagnosis, without evidence of disease progression. The early loss from the oncological follow-up programs of patients with a lower risk of early repalpse, without evidence of a recurrence or metastasis could be the consequence of a major complication among which we could assume an aspiration pneumonia secondary to a dysphagia, associated with an aggressive multidisciplinary treatment. Large tumor size and positive resection margins (R1 resection) are risk factors that support an intensive adjuvant approach in order to reduce the risk of recurrence, but the low grade of tumor, associating a lower risk of recurrence as well as the adverse events (AE) of adjuvant radiotherapy and chemotherapy justifies a more reserved therapeutic approach. Taking into account the longer life expectancy of these patients, it is recommended to use a more conformal irradiation technique in order to reduce doses to radiosensitive structures as well as to omit elective neck irradiation, taking into account the lower risk of lymph node involvement. The lack of guidelines that include very rare tumors including low grade chondrosarcoma of head and neck make a unified approach difficult, but the data presented even in case reports could contribute to choosing the regimen that offers the best therapeutic ratio.

Healthcare systems are mindful of the importance of proper diet and nutrition in reducing the risk of various chronic diseases resulting in hospitalizations. In this regard, they are focusing on promoting the intake of foods comprising various diets with health benefits, such as the ketogenic diet. In this meta-analysis, a total of 20 research studies on the effect of the ketogenic diet on the immune system were analyzed. The research studies were obtained from three databases: Google Scholar, PubMed, and Science Direct. From the meta-analysis, the odd ratio of a similar outcome of an improvement in the strength of immunity between the intervention and control group was 0.76. On the other hand, the p-value for the studies was 0.09, with 15 out of the 20 being considered statistically significant. The heterogeneity between the studies was I2 = 15%, signifying a low variability in the findings that is not by chance. The Ketogenic diet indeed has positive effects on immunity. Nonetheless, it can also result in negative effects that may harm human health.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

The Brazilian livestock is predominantly extensive, with approximately 90% of the production being sustained on pasture, which occupies around 20% of the territory. In the current climate change scenario and where cropland is becoming a limited resource, there is a growing need for a more efficient land use and occupation. It is estimated that more than half of the Brazilian pastures have some level of degradation; however there is still no mapping of the quality of pastures on a national scale. In this study, we mapped and evaluated the spatio-temporal dynamics of pasture quality in Brazil, between 2010 and 2018, considering three classes of degradation: Absent (D0), Intermediate (D1), and Severe (D2). There was no variation in the total area occupied by pastures in the evaluated period, in spite of the accentuated spatial dynamics, with a retraction in the center-south and expansion to the north, over areas of ​​native vegetation. The percentage of non-degraded pastures increased ~12%, due to the recovery of degraded areas and the emergence of new pasture areas as a result of the prevailing spatial dynamics. However, about 44 Mha of the pasture area is currently severely degraded. The dynamics in pasture quality were not homogeneous in property size classes. We observed that in the approximately 2.68 million properties with livestock activity, the proportion with quality gains was twice as low in small properties compared to large ones, and the proportion with losses was three times greater, showing an increase in inequality between properties with more and less resources (large and small, respectively). The areas occupied by pastures in Brazil present an unique opportunity to increase livestock production and make available areas for agriculture, without the need for new deforestation in the coming decades.

Background: Simulation plays a crucial role in health studies, as it helps medical students apply their theoretical knowledge in real-life situations. Moulage is one of the techniques that helps in making simulation more realistic or high-fidelity. It uses special effects to emulate wounds for a better understanding of what the wound is like visually. Still, moulage is expensive, time-consuming, resource-intensive, and requires the training of staff, which is why we need to find low-cost substitutes for moulage materials. Method: When searching the database “PubMed” for the terms “Low-cost and Medical moulage”, we retrieved 222 studies, out of which when excluding results not related to low-cost, we obtained 62 studies, from which when removing studies that do not contain information regarding moulage, we found two papers, after referring to citations and cited articles of those papers, we ended up with six studies. Based on the selected articles and additional articles sourced from their reference list, a total of 11 studies were included in the review. Results: We understand that moulage is a technique that helps make simulations come alive, but the resources required to use it are at times, expensive, which is why we need to find methods to do low-cost moulage, and many studies address that it can be as simple as using homemade ingredients. Students from a previous study have talked about their opinions regarding the realistic component of moulage and whether if it is any different from other moulages. Most of the students agreed that the moulage ranked well in face and content validity. However, further innovations must be introduced in the field to be widely spread and lead to newer opportunities. Conclusion: Although the research done under moulage is limited, it is accepted that moulage is helpful for simulation-based studies and that low-cost moulage can help make medical studies a better experience for students studying it. Students have a favorable opinion on the realistic aspect of the low-cost moulage applied to them. Newer methods can be introduced to moulage, and it can be implemented in low-income countries.

Background: Simulations have historically aided training programs by providing a realistic and holistic replication of professional scenarios and procedures. Simulations have developed over the past 40 years to include varying fidelities and modalities of simulation. Learning in a simulation-centered environment has benefits, ranging from improved patient care to specific skills acquisition while catering to students’ numerous and varied learning approaches. Simulation is a multifaceted field that benefits all parties, the teachers, the learners, and the patients. The application of simulation to medical education and its amalgamation with other modes and substitutes allows for a more integrated learning and testing curriculum that advances the current trajectory of medical education. Such developments, however, are limited to resource rich areas, leaving behind low-middle income countries to use traditional, less evolved methodologies and practices. This review aimed to explore different aspects of simulation and focus specifically on low-cost task trainers and their accessibility. Method: The purpose of the study was to assess the accessibility of low-cost task trainers in terms of cost-effectiveness, distribution, validation, and frequency within specific specialties. To do so, 84 PubMed publications have been screened, and 39 filtered research studies have collected the necessary data. After analyzing the papers, we classified the following information – process, specialization, validation (y/n), costs, development location, and year of publication. Results: After carefully analyzing the accumulated data from the selected 39 publications, we found that most studies (i.e., 6 out of 39) were published in 2020. Emergency Medicine was the most common specialty for which low-cost trainers were developed (9 out of 39 procedural simulators); Otolaryngology followed this with 8 out of 39 trainers and general surgery with 7/39 of the task-trainers. The price ranges fluctuated and fell within the price bracket of USD 0 to USD 400 collectively. Our review also uncovered the concentration of development of such innovations solely in high income countries (HICs). Conclusion: Simulation is an invaluable tool applicable to a diverse range of phases of medical education. Future conjunction of simulation with low-cost substitutes along with increased encouragement and enthusiasm towards developing cost effective simulation-based learning environments (SBLEs) with the reserves and requirements of these areas in mind may prove to be a reliable option for low and middle resource settings

The term low-resourced has been tossed around in the field of natural language processing to a degree that almost any language that is not English can be called "low-resourced"; sometimes even just for the sake of making a mundane or mediocre paper appear more interesting and insightful. In a field where English is a synonym for language and low-resourced is a synonym for anything not English, calling endangered languages low-resourced is a bit of an overstatement. In this paper, I inspect the relation of the endangered with the low-resourced from my own experiences.

Abstract: Imaging devices of less than 300,000 pixels are mostly used for sewage conduit exploration due to the petty nature of the survey industry in Korea. P articular ly , devices of less than 100,000 pixels are still widely used, and the environment for image processing is very bitter . Since the sewage conduit image s covered in this study ha ve a very low resolution (240 × 320 = 76,800 pixels), it is very difficult to detect cracks. Because most of the resolution of the sewe r conduit images are very low in Korea, this problem of low resolution was selected as the subject of study. Cracks were detected through a total of six steps of improving the crack in Step 2, finding the optimal threshold value in Step 3, and applying an algorithm to detect cracks in Step 5. Cracks were effectively detected by the optimal parameters in Steps 2 and 3 and the user algorithm in Step 5. Desp ite the very low resolution, the cracked image s showed 96.4% accuracy of detection, and the non cracked image s showed 94.5% accuracy . Moreover, the analysis was excellent in quality , also . It is believed that the findings of this study can be effectively u sed for crack detection with low resolution images.

Biosensors are essential tools which have been traditionally used to monitor environmental pollution, detect the presence of toxic elements and biohazardous bacteria or virus in organic matter and biomolecules for clinical diagnostics. In the last couple of decades, the scientific community has witnessed their widespread application in the fields of military, health care, industrial process control, environmental monitoring, food-quality control, and microbiology. Biosensor technology has greatly evolved from the in vitro studies based on the biosensing ability of organic beings to the highly sophisticated world of nanofabrication enabled miniaturized biosensors. The incorporation of nanotechnology in the vast field of biosensing has led to the development of novel sensors and sensing mechanisms, as well as an increase in the sensitivity and performance of the existing biosensors. Additionally, the nanoscale dimension further assists the development of sensors for rapid and simple detection in vivo as well as the ability to probe single-biomolecules and obtain critical information for their detection and analysis. However, the major drawbacks of this include, but are not limited to potential toxicities associated with the unavoidable release of nanoparticles into the environment, miniaturization induced unreliability, lack of automation, and difficulty of integrating the nanostructured-based biosensors as well as unreliable transduction signals from these devices. Although the field of biosensors is vast, we intend to explore various nanotechnology enabled biosensors as part of this review article and provide a brief description of their fundamental working principles and potential applications.

Cuticular waxes are a mixture of hydrophobic very-long-chain fatty acids and their derivatives accumulated in the plant cuticle. Most studies define the role of cuticular wax largely based on reducing non-stomatal water loss. The present study investigated the role of cuticular wax in reducing both low-temperature and dehydration stress in plants using Arabidopsis thaliana mutants and transgenic genotypes altered in the formation of cuticular wax. cer3-6, a known Arabidopsis wax-deficient mutant (with distinct reduction in aldehydes, n-alkanes, secondary n-alcohols, and ketones compared to wild type (WT)), was most sensitive to water loss; while dewax, a known wax overproducer (greater alkanes and ketones compared to WT), was more resistant to dehydration compared to WT. Furthermore, cold-acclimated cer3-6 froze at warmer temperatures, while cold-acclimated dewax displayed freezing exotherms at colder temperatures compared to WT. GC-MS analysis identified a characteristic decrease in the accumulation of certain waxes (e.g. alkanes, alcohols) in Arabidopsis cuticles under cold acclimation, which was additionally reduced in cer3-6. Conversely, the dewax mutant showed a greater ability to accumulate waxes under cold acclimation. FTIR spectroscopy also supported observations in cuticular wax deposition under cold acclimation. Our data indicate cuticular alkane waxes along with alcohols and fatty acids can facilitate avoidance of both ice formation and leaf water loss under dehydration stress, and are promising genetic targets of interest.

Purpose: Novel coronavirus disease (COVID-19) is the current global concern. Radiotherapy (RT), commonly employed in cancer management, has been considered one of the potential treatments for COVID-19 pneumonia. Here, we present the final report of the pilot trial evaluating the efficacy and safety of low-dose whole-lung irradiation (LD-WLI) in patients with COVID-19 pneumonia. Methods and Materials: We enrolled patients with moderate COVID-19 pneumonia who were older than 60 years. Participants were treated with LD-WLI in a single fraction of 0.5 or 1.0Gy along with the national protocol of COVID-19. The primary endpoints were improvement of SpO₂, the number of hospital/ICU stay days, and the number of intubations after RT and the secondary endpoints were alterations of the c-reactive peptide, interleukin-6, ferritin, procalcitonin, and D-dimer. The response rate (RR) was defined as a rise in SpO₂ upon RT with rising or constant trend in the next two days, and clinical recovery (CR) included patients who were discharged from the hospital or acquired SpO₂ ≥93% on room air. Results: Between 21 May 2020 and 2 July 2020, ten patients were enrolled. The median age was 75 years, 80% were male, and 80% had comorbidities. The first five patients received a single 0.5Gy-WLI, and others received 1.0Gy. Patients were followed for 2-14 days (median 5.5 days). Following one day, nine patients experienced an improvement in SpO₂. Five patients were discharged (median 6^th day, range 2^nd-14^th day), and four patients died (median 7^th day, range 3^rd-10^th day). Overall, the RR and CR were 60.0% and 55.5%, respectively. The RR and CR rates of 0.5- and 1.0Gy group were 80% vs 40% and 75% vs 40%, respectively. No acute radiation-induced toxicity was recorded. Conclusions: LD-WLI with a single 0.5Gy fraction seems to be a more appropriate dose to warrant further evaluation in a large-scale, randomized trial.

We review a number of preconditioners for the advection-diffusion operator and for the Schur complement matrix which in turn constitute the building blocks for Constraint and Triangular Preconditioners to accelerate the iterative solution of the discretized and linearized Navier-Stokes equations. An intensive numerical testing is performed onto the driven cavity problem with low values of the viscosity coefficient. We devise an efficient multigrid preconditioner for the advection-diffusion matrix which, combined with the commuted BFBt Schur complement approximation, and inserted in a 2 x 2 block preconditioner, provides convergence of the GMRES method in a number of iteration independent of the meshsize for the lowest values of the viscosity parameter. The low-rank acceleration of such preconditioner is also investigated showing its great potential.

The concept of using special electrical circuit design realize a "cold resistors", that is, an active resistor circuitry with lowered effective noise temperature, was first introduced about 80 years ago. Later on, various kinds of artificial resistors were applied in different research areas, such as gravitational wave detection, photo-amplifiers and quartz oscillators. Their proofs of concepts were experimentally proved. Unfortunately, the complete theory was not found even though several attempts had been published, sometimes with errors. In this paper, we describe a correct and complete circuit theoretical model of a cold resistor system. The results are confirmed by computer simulations. A design tools for this circuit is also shown.

Number of confirmed cases of COVID-19 caused by SARS-CoV-2 exceeded 5 million as of May 21, 2020. Global average of the case fatality rate of COVID-19 is about 7% so far. There exist variations in case fatality rates among countries. Particularly, Singapore and Qatar have exceptionally low case fatality rates with 0.1% while France’s rate is almost 20%. Since no magic bullet treatment for COVID-19 exists, we investigated SARS-CoV-2 strains specific to Singapore in this study to identify a clade with low pathogenicity. Variant analysis revealed that a clade with variants ORF1ab L3606F, A4489V, S2015R, T2016K, and N P13L is common in Singapore. Based on our analysis of variants and historical case statistics, the clade is dominant in a recent surge. Therefore, we suggest that low case fatality rate of Singapore possibly is attributed to the clade. Although contribution of each variant to the low pathogenicity is not clear, L3606F alone does not accomplish such low pathogenicity from the comparison with case fatality data from Japan, where L3606F is dominant. Further investigation is necessary to conclude to validate this finding.

In the last years, the development of low-cost GNSS sensors allowed monitoring in a continuous way movement related to natural processes like landslides with increasing accuracy and limited efforts. In this work, we present the first results of an experimental low-cost GNSS continuous monitoring applied to the unstable slope affecting the Madonna del Sasso Sanctuary (NW Italy). The courtyard of Sanctuary is built of two unstable blocks delimited by high cliff. Previous studies and non-continuous monitoring showed that blocks suffer a seasonal cycle of thermal expansion and long-term trend to downslope of few millimeters per year. The presence of continuous monitoring solution, could be an essential help to better understand the kinematics of unstable slope and to recognize the beginning of a possible paroxysm phase that could end with a failure of the unstable area. We tested the accuracy of the instruments and the first year of experimental measurements are presented. We also propose a methodological approach that considers the use of automatized procedures for the identification of anomalous trends and a risk communication strategy based on monitoring data.

A hydrothermal pretreatment of the microalga Nannochloropsis gaditana at mild temperatures has been studied in order to reduce N and O content in the biocrude obtained by hydrothermal liquefaction (HTL). The work is focused on the evaluation of temperature, reactor loading and time (factors) to maximize the yield of the pretreated biomass and the heteroatom contents transferred from the microalga biomass to the aqueous phase (responses). The study followed the factorial design and response surface methodology. An equation for every response has been obtained, which leads to the accurate calculation of the operating conditions required to obtain a given value of these responses. Temperature and time are critical factors with a negative effect on the pretreated biomass yield, but a positive one on the N and O recovery in the aqueous phase. The slurry concentration has to be low to increase heteroatom recovery and high to maximize the pretreated microalga yields

Over half of adult Americans now have diabetes or prediabetes and worse, this epidemic is now world-wide and shows no signs of slowing, with rates of both diabetes and diabetes-related health complications still rising. When advising patients with diabetes on food choices, many providers rely on nutrition guidelines provided by the American Diabetes Association (ADA), and these guidelines influence other recommendations across the globe. Given the alarming trends in diabetes, it is paramount to review the treatment guidelines to ensure they are based on rigorous and accepted scientific methods. Our review included the evidence cited by the ADA in support of its claims and recommendations for eating patterns to combat diabetes (see Description of Eating Patterns, Supplemental Appendix), as presented in the most current edition of the annual ADA’s Standards of Medical Care in Diabetes (2018 Standards). Our review also includes sources cited in the latest edition of the ADA’s Nutrition Therapy Recommendations for Adults with Diabetes (2014 Recommendations), which also informed the 2018 Standards. In October 2018 low carbohydrate was named as a recommended eating pattern by the ADA and European Association for the Study of Diabetes (EASD)⁵but only citations from the 2014 and early 2018 ADA documents were reviewed.

MEMThe PdNi film hydrogen sensors with Wheatstone bridge structure were designed and fabricated by the micro-electro-mechanical system (MEMS) technology. The integrated sensors consisted of four PdNi alloy film resistors. The interval two of them were shielded with silicon nitride film and used as reference resistance, while the others were used for hydrogen sensing. The PdNi alloy films and SiN films were deposited by magnetron sputtering. The morphology and microstructure of the PdNi films were characterized with X-ray diffraction (XRD). The output resistance signal was converted to millivolt output voltage signal for easy data acquisition. Hydrogen (H2) sensing properties of PdNi film hydrogen sensor with Wheatstone bridge structure was investigated under different temperatures (30℃, 50℃ and 70℃) and H2 concentrations (from 10 ppm to 0.4%). The hydrogen sensor demonstrated good response at different hydrogen concentrations and high repeatability in cycle testing under 0.4% H2 concentration. Under 10ppm hydrogen, the PdNi film hydrogen sensor had evident and collectable output voltage of 600 μV.

The beginning of industrialization human being has observed a variety of environmental troubles in the world. This industrialization has not only brought growth and affluence but ultimately troubled the ecosystem. One of the crashes is visible, in form of water contamination. Here the current study heavy metal contamination of water body has been discussed. Effluents from a great number of industries viz., tannery, textile, pigment & dyes, paint, wood processing, petroleum refining, electroplating, leather etc., have a major amount of heavy metals in their wastewater. The conventional technique of handling heavy metal pollution includes chemical oxidation, chemical precipitation, ion exchange, reverse osmosis, membrane separation, electrodialysis etc. These processes are expensive, energy intensive and frequently related with generation of poisonous by-product. Therefore, the adsorption has been examined as a cost-efficient technique of elimination of heavy metals from wastewater. In the current study different low-cost adsorbent has been a review as an abatement of heavy metal contamination from wastewater. These adsorbent comprise materials of natural origin like peat moss, zeolites, clay, and chitin are found to be an effective agent for removal of deadly heavy metals like Pb, Cd, Zn, Cu, Ni, Hg, Cr etc. Separately from these, a variety of agricultural wastes like rice husk, waste tea, neem bark, black gram; Turkish coffee, walnut shell etc. were also known as a powerful adsorbent for heavy metal removal. at the side of that low-cost industrial byproduct like fly ash, lignin, iron (III) hydroxide and red mud, coffee husks, Areca waste, tea factory waste, sugar beet pulp, battery industry waste, blast furnace sludge, waste slurry, sea nodule remains and grape stalk wastes have been discovered for their technical possibility to eliminate toxic heavy metals from impure water.

Computational Fluid Dynamics (CFD) is utilized to study entropy generation for the rarefied steady state laminar 2-D flow of air-Al2O3 nanofluid in square cavity equipped with two solid fins at the hot wall. Such flows are of great importance in industrial applications, such cooling of the electronic equipment’s and nuclear reactors. In the current study, effects of Knudsen number (Kn), Rayleigh number (Ra) and the nano solid particles volume fraction (ϕ) on the entropy generation are investigated. The values of parameters considered in this work are as follows: 0≤Kn≤0.1, 〖10〗^3≤Ra≤〖10〗^6,0≤ϕ≤0.2. Length of the fins (LF) is considered to be fixed and equals to 0.5 m, whereas the location of the fins with respect to the lower wall (HF) is set to 0.25 and 0.75 m. Simulations demonstrate that there is an inverse direct effect of Kn on the entropy generation. Moreover, it is found that when Ra is less than 104, the entropy generation, due to the flow, increases as ϕ increases. In addition, the entropy generation due to the flow will decrease at Ra greater than 104 as ϕ increases. Moreover, the entropy generation due to heat will increase as both the ϕ and Ra increase. In addition, a correlation model of the total entropy generation as a function of all of the investigated parameters in this study is proposed. Finally, an optimization technique is adapted to find out the conditions at which the total entropy generation is minimized

Recent advances in single-atom catalysis resulted in readily accessible materials whose application in most catalytic reactions mediated by conventional nanoparticle-based catalysts often results in higher activity and selectivity. Can we expect catalysis by atomically dispersed atoms to find practical applications? Which are the hurdles to be overcome prior to widespread uptake of atomically dispersed metals in industrial synthetic processes and in hydrogen fuel cells?

A The agri-food sector is in full renovation, continuously demanding new systems that allow farmers to facilitate their work. Efficient agricultural practices are essential for increasing farm profitability. Efficient agricultural practices can be increased by understanding and managing water neeeds. However, real-time monitoring of water needs is currently slow, and irrigation decisions are based on previous data or physical evidence. Furthermore, the prices of automatic systems for collecting data from several sources (soil and climate) are expensive and the autonomy is very low. Emerging Internet of Things (IoT) technologies such as wireless sensor networks can be used to collect vast amounts of data recorded via apps. By means of an LPWAN communication the farmer can know in real time the state of his crops thanks to a large number of sensors connected wirelessly and distributed across his farm. This paper presents a low consumption solution based on LoRaWAN technology. The wireless sensor node, called BoX, exhibits very low power since it has been optimized both in terms of hardware and software. The result is a higher degree of autonomy than commercial motes. That will allow the farmer to have all the information necessary to achieve an efficient management of his crops with full autonomy.

An ultra-low anti-reflection optical coating on both surfaces of a plastic cover slip was studied for use in confocal image measurement. The optical reflectance at a wavelength of 632.8 nm was less than 0.1% when the coated sample was placed in a liquid having a refractive index of 1.34 close to the aqueous solution of the biomaterial. The high- and low-index coating films, Substance-2 (PrTiO3) and silicon dioxide (SiO2), were measured by an ellipsometer to determine their optical refraction indices and extinction coefficients. Theoretically, when the two layer thicknesses are designed using the optical admittance diagram of the cover slip to approach the equivalent index of 1.34, a reflectance of 1.6×10-5% in the liquid could be obtained. Experimentally, the reflectance of the sample deposited on the two faces of the cover slip was 4.223±0.145% as measured in the air; and 0.050±0.002% as measured by a He-Ne laser in the liquid.

The atherosclerosis, a chronic and inflammatory disease that occurs when there are high levels of low-density lipoprotein (LDL) on plasma. This important risk factor for development of cardiovascular disease (CVD) is the main cause of death worldwide. MicroRNAs have recently emerged as potential biomarkers and therapeutic target for lipid metabolism disorders. In this review, we will provide profile of surrounding miRNAs that have demonstrated being regulators of PCSK9, LDLR and APOB100 genes. Recent work has identified the mir-148, mir-128, mir-27a/b, mir-185, mir-301, mir-130 as important regulators of this pathway because they decrease supply of LDL receptors through interaction with PCSK9. Inhibition of LDLR expression cause elevation of plasma LDL levels which induces atherosclerosis. While mir-30c, mir-122, mir-34 decrease MTTP, which promotes degradation of APOB100 preventing assembly and secretion of VLDL. We conclude that, when overexpressed, mir-148a, mir128 and mir-27a/b, mir-122 and mir-34 are related to decrease in LDLR, facilitating occurrence of atherosclerosis. While mir-30 has been linked to decreased atherosclerosis. Detection of miRNAs profile could be used in the future as a biomarker for disturbs linked to c-LDL uptake and in future anti-miRNAs therapies may be used in the treatment of atherosclerosis.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

This randomized control trial aims to test the hypothesis that twice-daily nurse-administered saline enema(SE) is comparable to physician-administrated SE in very low birth weight infants (VLBW) with meconium obstruction of prematurity (MOP). MOP is defined as no bowel opening for 48 h, and treatment failure is defined as the need for additional intervention and safety. Twice-daily SE was administered by accredited nurses, surgeons/neonatologists using standardized protocols. The outcomes were comparability of nurse to physician-administered SE in terms of frequency of administration, catheter insertion length and volume of enema, daily maximum meconium output, and treatment failure, defined as the need for additional intervention. Safety outcomes were evaluated. Twenty-eight infants were managed with SE. 389 SE were administered, 96 and 293 in 750-999g and 1000-1500g birth weight groups, respectively. Nurses administered 72.9% and 81.5% of SE in 750-999g and 1000-1500g birth weight groups, respectively. Physicians performed the rest of the SE. Daily meconium output was comparable in nurse and physician-administered SE in both groups. There were no treatment failures or adverse events in both SE group. SE administered by nurses was found to be comparable in terms of safety, efficacy, and frequency of administration to that of physician-administered SE.

In recent times, the increasing concern for climate control has led to the widespread application of grid-connected inverter (GIC) based renewable energy systems. In addition, the increased usage of non-linear loads and electrification of the transport sector cause ineffective grid-frequency management and the introduction of harmonics. These grid conditions affect power quality and result in uncertainty and inaccuracy in monitoring and measurement. Incorrect measurement leads to overbilling/underbilling, ineffective demand and supply forecasts for the power system, and inefficient performance analysis. To address the outlined problem, a novel three-phase frequency component extraction and power measurement method based on Digital Lock-in Amplifier (DLIA) and Digital Lock-in Amplifier Frequency-Locked Loop (DLIA-FLL) is proposed to provide accurate measurement under the conditions of harmonics and frequency offset. A combined filter with a lowpass filter and notch filter for DLIA is employed to improve computation speed. A comparative study is performed to validate the performance of the proposed power measurement method, by comparing the proposed method to the windowed interpolated fast Fourier transform (WIFFT). The ZERA COM 3003 (a commercial high-accuracy power measurement instrument) is used as the reference instrument in the experiment

Healthcare leaders are faced with many financial challenges in the contemporary environment, leading to many bankruptcies in recent years. What is not well understood are the specific conditions that lead to organizational economic failure. Ideally, hospital leaders could examine the literature for guidance to predict bankruptcy before it occurs. However, existing regression methods have proven inadequate, especially when the finance variables follow a nonnormal frequency pattern. Furthermore, the regression approach encounters difficulties due to multicollinearity and nonnormality issues. Therefore, an alternate stochastic approach for predicting the probability of hospital bankruptcy is warranted. This new method includes computing and interpreting the correlations between the hospital’s revenue and expenses for bivariate lognormal data, calculating the risk of bankruptcy due to the mismatch between revenues and expenses, determining the likelihood of a hospital’s expense exceeding the state’s median expense level, and evaluating a hospital’s financial memory level. Ultimately in our research, we demonstrate a novel approach to anticipate hospital bankruptcy, which can be particularly useful for health policy analysts and hospital leaders in making informed financial decisions and proactively managing risks to ensure the sustainability and stability of their institutions.

Arduino microcontrollers are being used for a wide range of technological and biomedical applications such as image classification, computer vision, brain-computer interaction and vision experiments. Here I present a new cost-effective mini-device based on RGB LED flicker stimulation for the assessment of polychromatic temporal resolution of visual function. The visual device configuration allows for relative luminance thresholding, mono- and polychromatic critical flicker fusion frequency assessment. The results demonstrate the steady white visual perception of a trichromatic flicker stimulus beyond the critical flicker fusion frequency, as predicted by Talbot´s law for monochromatic stimuli. The trichromatic critical flicker fusion frequency (tFCC) depends on the relative luminance threshold at the light-adaptation level. Finally, wavefront measurements demonstrate that high-order aberrations improve the temporal resolution of visual function.

Primary Ciliary Dyskinesia (PCD) is a rare genetic disorder characterized by alterations in motile cilia func-tion. The diagnosis of PCD is challenging due to the lack of standardized methods in clinical practice. High-speed video microscopy analysis (HSVA) directly evaluates ciliary beat frequency (CBF) in PCD. Recently, open-source ciliary analysis software applications have shown promise in measuring CBF accurately. How-ever, there is limited knowledge about the performance of different software applications, creating a gap in understanding their comparative effectiveness in measuring CBF in PCD. We compared two open-source software applications, CiliarMove and Cilialyzer, against the manual count method. We used videos rec-orded at high-speed of nasal ciliary brush samples from PCD patients and healthy controls. All three meth-ods showed lower median CBF values in PCD patients than healthy controls. CiliarMove and Cilialyzer identified lower CBF in PCD patients, similar to the manual count. Cilialyzer, CiliarMove and manual count demonstrated statistical significance (p-value < 0.0001) in the difference of median CBF values be-tween PCD and healthy controls. These findings support the utility of open-source software-based analysis tools. Further studies are needed to validate these findings with other genetic variants and identify the op-timal software for accurate CBF measurement in PCD.

The Dual-Frequency Precipitation Radar (DPR) on the Core GPM satellite provides spaceborne 3-dimensional observations of the precipitation field and surface rainfall rate with quasi global coverage. The present study evaluates the behavior of liquid precipitation intensity, radar reflectivity factor (ZKu and ZKa) and Drop Size Distribution (DSD) parameters (weighted mean diameter Dm and intercept parameter Nw) of the GPM DPR derived products version 07 from 2014 to 2023. Observations from seven Parsivel disdrometers located in different topographic zones in the Western Mediterranean are taken as ground reference. Four matching techniques between satellite estimates and ground level observations were tested, and best results were found for the so-called optimal comparison approach. Overall, GPM DPR products capture well the variability of the observed DSD at different rainfall intensities. However, overestimation of the mean Dm and underestimation of the mean Nw are observed, being much more sensitive to errors in drop diameters larger than 1.5 mm. Moreover, lowest errors were found for radar reflectivity factor and Dm, and highest for Nw and rainfall rate. In addition, the GPM DPR convective and stratiform classification was tested and it was found a substantial overestimation of stratiform cases compared to disdrometer observations.

Nasal high-frequency oscillatory ventilation (nHFOV) has emerged as an effective initial and rescue noninvasive respiratory support mode for preterm infants with respiratory distress syndrome (RDS). Multiple noninvasive respiratory support modes are currently available in Romania, but little is known about nHFOV use in Romanian neonatal intensive care units (NICUs). We aimed to identify the usage extent and clinical application of nHFOV in Romania. A structured web-based questionnaire was designed to find the rate of nHFOV use and knowledge of this new method of noninvasive respiratory support in Romanian level III NICUs. The questionnaire was addressed to the leaders of all level III Romanian NICUs. Using multiple-choice, open-ended, and yes/no questions, we collected information on the NICU’s size, noninvasive respiratory support modes used, nHFOV use, indications, settings, nasal interfaces, secondary effects, and equipment used. Descriptive statistics and comparisons were performed using IBM SPSS Statistics 26.0. A total of 21/23 (91.3%) leaders from level III NICUs (median [IQR] number of beds of 10 [10-17.5]) responded to the survey. The most frequently used noninvasive ventilation modes were CPAP mode on mechanical ventilators (76.2%), followed by NIPPV (76.2%), heated, humidified high flow nasal cannula (HHHFNC) (61.9%), and nHFOV (11/21 units; 52.4%); 5/11 units reported frequent nHFOV use (in 2 or more newborns/month) in both term and preterm infants. The main indications reported for nHFOV use were CPAP failure (90.9%), hypercapnia (81.8%), and bronchopulmonary dysplasia (72.7%). 10/11 units reported setting a mean airway pressure (MAP) equal to the CPAP level plus 1-2 cmH₂O on rescue nHFOV after CPAP failure. Both dedicated equipment (45.5%) and hybrid ventilators (63.6%) were used for nHFOV delivery, with face/nasal masks and short binasal prongs being the most commonly used nasal interfaces (90.9% and 72.7%, respectively). Air leaks at the interface level (90.9%), thick secretions (81.8%), and airway obstruction (63.6%) were the most frequently mentioned adverse effects of nHFOV; none of the units mentioned pneumothorax as an adverse effect. Only 3 of the NICUs had a written protocol for nHFOV use. Initial, minimum, and maximum amplitude and initial and minimum MAP settings used were significantly higher with hybrid ventilators as compared to dedicated equipment (p<0.05). Most units not yet using nHFOV cited lack of equipment, experience, training, or insufficient information and evidence for the clinical use and outcome of nHFOV use in neonates as the main reasons for not implementing this noninvasive respiratory mode. Our survey showed that nHFOV is already used in more than half of the Romanian level III NICUs to support term and preterm infants with respiratory distress despite a lack of consensus regarding indications and settings during nHFOV. A need for training for nHFOV use was identified, and efforts are needed at the national level to develop courses and training sessions, including using simulation workshops, to offer more information on optimal nHFOV use in clinical practice.

We hypothesize that the first ancestral "ante-cell" molecular structures, i.e., first RNAs and peptides which gradually transformed into real cells once the Earth had cooled sufficiently for organic molecules to appear there, have leaved traces in RNAs and genes of present cells. We propose a circular RNA which could have been one of these ancestral structures whose vestigial pentameric subsequences would mark the evolution from this key moment when the ante-cells have begun to join the living organisms. In particular, we propose that in present RNAs (ribosomal or messenger) playing an important role in the metabolism of current cells, we look for traces of the proposed primitive structure in the form of pentamers (or longer fragments) belonging to their nucleotide sequence. The result obtained can be summarized in the existence of a gradient of occurrence of such pentamers, with a high frequency for the most vital functions (protein synthesis, nucleic synthesis, cell respiration, etc.). This gradient is also visible between organisms, from the oldest (Archaea) to the most recent (Eukaryotes) in evolution of species.

The penetrability and directivity of ultrasound in different media is of interest in engineering and medical applications (imaging, nondestructive testing, sonochemistry, among others). The nonlinearity of a liquid can be used in the parametric antenna framework to generate low-frequency components with particular features from several ultrasonic signals at the source. Bubbly liquids are dispersive liquids in which a small amount of tiny gas bubbles leads to the increase of the nonlinear parameter of the media over certain frequency ranges. Parametric antenna applied to this huge nonlinear media gives rise to low-frequency components with relatively small intensity at the source. The evolution of a low-frequency component (difference-frequency component obtained from two primary signals) during its propagation in a bubbly liquid is somehow unknown. It is thus interesting to analyse its characteristics to establish whether this component can benefit from the quality of its own frequency and from the primary frequencies in terms of directivity and penetrability into the medium. It must be noted that no such study in bubbly liquids exists in the litterature, but only for homogeneous media. To this end, several numerical models developed previously are used here to analyse the difference-frequency component obtained from a parametric antenna emitting from two ultrasonic signals at the source in one and two-dimensional domains. These models allow us to observe the behavior of this frequency component. An angle that measures the directivity of a beam is also defined. Our results show a point hardly found in the literature: the high directivity and the huge penetrability of the secondary beam associated to the difference-frequency component into the bubbly liquid, compared to the same frequency signal excited directly from the source in the bubbly liquid and to the parametric acoustic array in homogeneous fluids.

An optical frequency comb (OFC) generator based on an electro-optic Talbot laser and cross-phase modulation (XPM) in a high nonlinear fiber (HNLF) is designed and demonstrated. The Talbot laser is an electro-optic frequency shifting loop to produce repetition rate multiplied pulses, and these pulses working as a pump signal induce XPM process in the HNLF to modulate the phase of a probe signal. At the output of the HNLF, OFCs with a multiplied line-spacing can be generated. The effects of the pump power and the HNLF length on the performance of the generated OFCs are theoretically analyzed. In the experiments, the line-spacing of the generated OFCs is respectively multiplied to be 10 GHz, 15 GHz and 20 GHz with a factor of 2, 3 and 4. The center of the OFCs is tuned in a 4-nm range by adjusting the wavelength of the probe signal.

A review on planar printed structures that are based on Matryoshka-like geometries is presented. These structures use the well-known principle of Matryoshka dolls that are successively nested inside each other. The well-known advantages of the planar printed technology and of the meandered nested Matryoshka geometries are combined to generate miniaturized, multi-resonance and/or wideband configurations. Both metal and complementary slot structures are considered. Closed and open configurations are analyzed. The working principles are explored do get physical insight of their behavior. Low cost and single layer applications as frequency selective surfaces, filters, antennas, and sensors, in the microwave frequency region, are reviewed. Potential future research perspectives and new applications are discussed.

Adjustable frequency converters are widely used in modern automated asynchronous drives due to their high efficiency and high responsiveness control strategies. Control algorithms for frequency converters are divided into two main groups: constant frequency commutation and random frequency commutation. Research results on various commutation frequencies, conducted using Matlab/Simulink software, show that the use of random frequency commutation provides better efficiency by significantly reducing the amplitude of harmonic oscillations at different frequencies, with a reduction in switching losses in transistors. Currently, a converter with random frequency commutation is being researched and applied in the direct torque control system. The traditional direct control system, based on a two-level inverter, is widely used due to its simplicity and ease of implementation. However, this method results in the output current of the two-level converter, supplied to the motor stator, having many harmonic distortions, leading to strong torque fluctuations regardless of the rotation speed and ultimately causing additional losses in the stator windings and reducing the motor's lifespan. To enhance the efficiency of automated asynchronous drives, this article presents an algorithm for a direct control system based on a three-level NPC inverter using a PI speed regulator. The proposed algorithm's research is validated in the Matlab/Simulink environment. The research results show that in the absence of harmonic filtering, the stator current harmonic distortion coefficient is approximately 11%, and torque fluctuations are less than 5% of the resistive torque. The fluctuations between the two capacitors remain almost unchanged throughout the entire process.

This paper presents the design and experimental results of a long cavity length Nd: YAG laser with large stable zone for water jet guided laser (WJGL) applications. The design is based on the light transmission matrix and resonator stability conditions, aiming to achieve a large stable zone and a short cut-off thermal focal length (CTFL). A folded concave resonator is researched to enhance the cavity length, and the influence of the tun-able cavity arm length on the oscillating beam in the resonator and in the YAG crystal is theoretically studied. Moreover, the effects of the output mirror curvature and the cavity arm length on the range of the stable area and the cut-off thermal focal length are also investigated. Experimental results show that a stable green laser output is obtained after second harmonic generation (SHG), with a pulse width ranging from 43ns to 143ns within the laser operating frequency range of 5-20kHz. At an operation frequency of 10kHz, the output power is 21.33W, and the instability of the output power within 400 minutes is 0.88%. The laser source achieves a maximum power of 25.7W at 20kHz, and the maximum single pulse energy reaches 2.7mJ at 6kHz. Finally, this is used as the laser source to couple with a water jet with a diameter of 100 microns, achieving a lossless water conductivity transmission over 60mm length with a peak power density of 0.742GW/cm2. These results demonstrate the suitability of the designed laser source for WJGL technology research.

This paper first introduces the main classification of brain diseases and the main causes of these diseases. It is followed by wavelet analysis, which is a mathematical function or wave-like pattern used to transform data, which can decompose the signal into different wavelet functions, each of which is related to a specific scale or frequency. Wavelet analysis has been applied in many fields such as image processing, data analysis and engineering. In addition, wavelet is also used in the analysis of biological signals. Wavelet analysis breaks down brain signals, such as EEG or fMRI data, into various frequency components at different scales. Wavelet analysis provides time-frequency localization. Pattern recognition can be enhanced by isolating salient features in the data. Wavelet denoising can effectively separate noise from underlying brain signals. Wavelet denoising usually adopts threshold method. Wavelet analysis can enhance pattern recognition by isolating salient features in the data. Researchers can train machine learning models based on these wavelet-derived features to recognize specific patterns associated with different neurological disorders. Wavelet analysis can track these changes by continuously evaluating the frequency content of the neuroimage data over time. Through continuous efforts, wavelet theory and technology have become valuable tools in the field of neuroscience and brain disease research.

Species richness is a widely used measure for assessing the diversity of a particular area. However, observed richness often underestimates the true richness due to resource limitations, particularly in the small-sized sample or highly heterogeneous assemblage. Estimating species richness in a large-scale region typically involves an integrated data set consisting of subsamples collected independently from different subregions. However, the pooled sample of integrated data is no longer a random sample from the entire region, and the use of different sampling schemes results in variations in data formats. Consequently, employing a single sampling distribution to model the pooled sample becomes impractical, rendering existing richness estimators inadequate. This study theoretically explains the applicability of Chao's lower bound estimators in estimating species richness for large-scale areas using the pooled sample. Additionally, a new nonparametric estimator is introduced, which adjusts the bias of Chao's lower bound estimator by leveraging the Good-Turing frequency formula. This proposed estimator only utilizes the pooled sample's singleton, doubleton, and tripleton richness. Simulated data sets across various models are employed to demonstrate the statistical performance of the estimator, showcasing its ability to reduce bias and provide accurate 95% confidence intervals. Real data sets are also utilized to illustrate the practical application of the proposed approach.

The gate resistance is a parasitic element in transistors for RF and millimeter-wave circuits that can negatively impact power gain and noise figure. To develop accurate device models, a reliable measurement methodology is crucial. This article reviews the standard measurement methodology used in the literature and proposes also an additional method, which is evaluated using suitable test structures in a 16nm FinFET process. The advantages and disadvantages of the two approaches are discussed along with their respective application scenarios

Two algorithms of data processing are proposed to shorten the unmeasurable dead-zone close to the zero-position of measurement, i.e., the minimum working distance of a dispersive interferometer using optical frequency comb, which is a critical issue in millimeter-order short-range absolute distance measurement. After demonstrating the limitation of the conventional data processing algorithm, the principles of the proposed algorithms, namely the spectral fringe algorithm, and the combined algorithm that combines the spectral fringe algorithm with the excess fraction method, are presented, together with simulation results for demonstrating the possibility of the proposed algorithms for shortening the dead-zone with a high accuracy. An experimental setup of dispersive interferometer is also constructed for implementing the proposed data processing algorithms over spectral interference signals. Experimental results demonstrate that the dead-zone by the proposed algorithms can be as small as half of that by the conventional algorithm while the measurement accuracy can be further improved with the combined algorithm.

Damage detection based on modal parameter changes becomes popular in the last decades. Nowadays are available robust and reliable mathematical relations to predict the natural frequency changes if damage parameters are known. Using these relations, it is possible to create databases containing a large variety of damage scenarios. Damage can be thus assessed by applying an inverse method. The problem is the complexity of the database, especially for structures with more cracks. In this paper, we propose two machine learning methods, namely the random forest (RF) and the artificial neural network (ANN) as search tools. The databases we developed contain damage scenarios for a prismatic cantilever beam with one crack and ideal and non-ideal boundary conditions. The crack assessment is made in two steps. First, a coarse damage location is found from the networks trained for scenarios comprising the whole beam. Afterward, the assessment is made involving a particular network trained for the segment of the beam on which the crack is previously found. Using the two machine learning methods, we succeed to estimate the crack location and severity with high accuracy for both simulation and laboratory experiments. Regarding the location of the crack, which is the main goal of the practitioners, the errors are less than 0.6%. Based on these achievements, we concluded that the damage assessment we propose, in conjunction with the machine learning methods, is robust and reliable.

The term deviation frequency denotes the boundary between the variable part of the amplitude and phase scintillation spectrum and the part of uninformative noises. We suggested the concept of the “characteristic deviation frequency” during the observation period which is defined as the most probable value of the deviation frequency under current local conditions. This work is a case study of the characteristic deviation frequency (fd) registered for GPS, GLONASS, Galileo and SBAS signals under quiet and weakly disturbed geomagnetic conditions in April 2021 at the mid-latitude GNSS station. Our results demonstrated that the fd value for all signal components of GPS, GLONASS and GALILEO signals varied within 15-22 Hz. The characteristic deviation frequency was 20 Hz for the mentioned GNSS signals. In difference, the deviation frequency was limited within 13-20 Hz for SBAS with the lower characteristic deviation frequency at 18 Hz. We assume that the concept of the characteristic deviation frequency can be used to determine the optimal sampling rate of the GNSS carrier phase data for the ionospheric studies. The characteristic deviation frequency can also characterize the state of the regular trans-ionospheric radio channel.

Improving the acquisition and retention of a new motor skill is of great importance. The present study (i) investigated the effects of difficulty manipulation strategies (gradual difficulty), combined with different modalities of feedback (FB) frequency on performance accuracy and consistency when learning a novel fine motor coordination task, and (ii) examined relationships between novel fine motor task performance and executive function (EF), working memory (WM), and perceived difficulty (PD). Thirty-six, right-handed, novice physical education students volunteered to participate in this study. Participants were divided into three progressive difficulty groups (PDG), 100% visual FB (FB1), 50% FB (FB2), and 33% FB (FB3). Progressive difficulty was increased by the manipulation of the distance to the target; 2 m, 2.37 m, and 3.56 m. Three FB modalities were investigated (i.e.: 100% visual FB (100% FB), 50% reduced feedback condition (50% RFB), and 33% reduced feedback conditions (33% RFB)). Performance assessments were conducted following familiarization, acquisition, and retention learning phases. Two stress-conditions of dart throws were investigated (i.e.: free condition (FC) and time pressure condition (TPC)). After the learning intervention, data showed that, under the free condition, the 100% FB group had a significant improvement in accuracy during all learning phases. Under time pressure condition, for the 50% RFB and the 33% RFB group, the measured variable (accuracy and consistency) showed a significant linear improvement in performance. The association between the percentage of RFB frequencies and the task difficulty (50% group) may be a more appropriate and manageable cognitive load compared to the 33% RFB and the 100% FB group. The present findings could have practical implications for practitioners because, while strategies are clearly necessary for improving learning, the efficacy of the process appears to be essentially based on the characteristics of the learners.

This paper presents an improved droop control strategy for grid-connected inverter power stability and power quality under distorted with consideration of grid fluctuation and inter-harmonics. An instantaneous frequency without PLL and amplitude of capacitor voltage feed-forward control strategy is given to power stability control, meanwhile a grid current feedback control is given by an incomplete derivation with a high-pass filter, so that the harmonics and inter-harmonics current can be suppressed. These approaches can provide both good active and reactive power dynamic response under fluctuation of frequency, and rejection ability against harmonic and inter-harmonic voltage. Based on model of inverter, the proposed control strategies are designed in detail. Simulations and experiments are present to validate the effectiveness of proposed method.

Eddy current testing can be used to interrogate steels but it is hampered by the lift-off distance of the sensor. Previously, the lift-off point of intersection (LOI) feature has been found for the pulsed eddy current (PEC) testing. In this paper, a lift-off invariant inductance (LII) feature is proposed for the multi-frequency eddy current (MEC) testing, which merely targets the ferromagnetic steels. That is, at a certain working frequency, the measured inductance signal is found nearly immune to the lift-off distance of the sensor. Such working frequency and inductance are termed as the lift-off invariant frequency (LIF) and LII. Through simulations and experimental measurements of different steels under the multi-frequency manner, the LII has been verified to be merely related to the sensor parameters and independent of different steels. By referring to the LIF of the test piece and using an iterative inverse solver, one of the steel properties (either the electrical conductivity or magnetic permeability) can be reconstructed with a high accuracy.

Chaparral shrublands are the dominant wildland vegetation type in southern California and the most extensive ecosystem in the state. Disturbance by wildfire and climate change have created a dynamic landscape in which biomass mapping is key in tracking the ability of chaparral shrub-lands to sequester carbon. Despite this importance, most national and regional scale estimates do not account for shrubland biomass. Employing plot data from several sources, we built a random forest model to predict above ground live biomass in southern California using remote sensing data (Landsat NDVI) and a suite of geophysical variables. By substituting the NDVI and precipi-tation predictors for any given year we were able to apply the model to each year from 2000-2019. Using a total of 980 field plots, our model had a k-fold cross validation R2 of 0.51 and a RMSE of 3.9. Validation by vegetation type ranged from R2 = 0.17 (RMSE=9.7) for Sierran mixed conifer to R2 = 0.91 (RMSE = 2.3) for sagebrush. Our estimates showed an improvement in accuracy over a two other biomass estimates that included shrublands, with an R2 = 0.82 (RMSE = 4.7) compared to R2 = 0.068 (RMSE = 6.7) for a global biomass estimate and R2 = 0.29 (RMSE = 5.9) for a regional biomass estimate. Given the importance of accurate biomass estimates for resource managers we calculated the mean year 2010 shrubland biomass for the four national forests which ranged from 3.5 kg/m2 (Los Padres) to 2.3 kg/m2 (Angeles and Cleveland). Finally, we compared our estimates to field-measured biomass from the literature summarized by shrubland vegetation type and age class. Our model provides a transparent and repeatable method to generate biomass measure-ments in any year, thereby providing data to track biomass recovery after management actions or disturbances such as fire.

Abstract: The article proposes to consider the possibility of connecting the problems of engineering synthesis of frequency control systems for asynchronous electric drives with the basic provisions of the theory of identification of asynchronous electric motors based on the equations of a generalized AC electric machine.The article presents the results of experimental studies of load parrying processes in asynchronous electric drives with vector and scalar controls. These results indicate the absence of fundamental advantages as processes in a drive with vector control. This advantage should have manifested itself in a more efficient formation of the moment and fast transients. It is suggested that the reason for this is in too significant errors, assumptions and simplifications of the equations adopted in the derivation of vector control and which are its theoretical basis. A method is proposed for describing asynchronous electric motors by nonlinear transfer functions, which made it possible to formulate the principle of correction of electric drives and a method for assessing their efficiency.The article shows. that the correction based on the proposed nonlinear transfer functions of the induction motor is much more efficient than the traditional vector control, which was confirmed by detailed experiments and modeling. The results of the most important of which are given in the article. An assumption was made. that the advantage in efficiency is due to a more accurate identification of the dynamics of an asynchronous electric motor with a gear function instead of vector equations.

Research on Traffic Light Recognition (TLR) has grown in recent years, primarily driven by the growing interest in autonomous vehicles development. Machine Learning algorithms have been widely used to that purpose. Mainstream approaches, however, require large amount of data to properly work, and as a consequence, a lot of computational resources. In this paper we propose the use of Expert Instruction (IE) as a mechanism to reduce the amount of data required to provide accurate ML models for TLR. Given an image of the exterior scene taken from the inside of the vehicle, we stand the hypothesis that the picture of a traffic light is more likely to appear in the central and upper regions of the image. Frequency Maps of traffic light location were thus constructed to confirm this hypothesis. The frequency maps are the result of a manual effort of human experts in annotating each image with the coordinates of the region where the traffic light appears. Results show that EI increased the accuracy obtained by the classification algorithm in two different image datasets by at least 15%. Evaluation rates achieved by the inclusion of EI were also higher in further experiments, including traffic light detection followed by classification by the trained algorithm. The inclusion of EI in the PCANet achieved a precision of 83% and recall of 73% against 75.3% and 51.1%, respectively, of its counterpart. We finally presents a prototype of a TLR Device with that expert model embedded to assist drivers. The TLR uses a smartphone as a camera and processing unit. To show the feasibility of the apparatus, a dataset was obtained in real time usage and tested in an Adaptive Background Suppression Filter (AdaBSF) and Support Vector Machines (SVMs) algorithm to detect and recognize traffic lights. Results show precision of 100% and recall of 65%.

Radio Frequency Interference (RFI) detection and characterization play a critical role to in ensuring the security of all wireless communication networks. Advances in Machine Learning (ML) have led to the deployment of many robust techniques dealing with various types of RFI. To sidestep an unavoidable complicated feature extraction step in ML, this paper proposes an efficient end-to-end method using the latest advances in deep learning to extract the appropriate features of the RFI signal. Moreover, this study utilizes the benefits of transfer learning to determine both the type of received RFI signals and their modulation types. To this end, the scalogram of the received signals is used as the input of the pre-trained convolutional neural networks (CNN), followed by a fully-connected classifier. This study considers a digital video stream as the signal of interest (SoI), transmitted in a real-time satellite-to-ground communication using DVB-S2 standards. To create the RFI dataset, the SoI is combined with three well-known jammers namely, continuous-wave interference (CWI), multi- continuous-wave interference (MCWI), and chirp interference (CI). This study investigated four well-known pre-trained CNN architectures, namely, AlexNet, VGG-16, GoogleNet, and ResNet-18, for the feature extraction to recognize the visual RFI patterns directly from pixel images with minimal preprocessing. Moreover, the robustness of the proposed classifiers is evaluated by the data generated at different signal to noise ratios (SNR).

Background: The dietary factors and nutrients contributing to the prevention of microalbuminuria in type 2 diabetic nephropathy is unclear, so we investigated dietary factors affecting urinary albumin excretion in patients with type 2 diabetes. Methods: 42 patients with type 2 diabetes were participated, the subjects were divided to a normal albuminuria group (urinary albumin / creatinine ratio of less than 30 mg / g Cr) and a microalbuminuria group of 30 mg / g to 299 mg / g Cr. We performed casual blood sampling and conducted a food frequency questionnaire survey. Results: There were no significant differences in age, BMI and other physiological and biochemical data, the average daily intake of energy and many of nutrients, while β-cryptoxanthin was significantly lower in the microalbuminuria group than in the normal group (506.4 ± 793.9 μg/day vs. 715.3 ± 500.3 μg/day, p <0.05). The intake of 17 food groups per day showed that the intakes of fruits were significantly lower in the microalbuminuria group than in the normal group (76.9 ± 134.1 g vs. 111.9 ± 84.5 g, p <0.05). Conclusion: These results suggest that fruits and foods rich in β-cryptoxanthin would make it possible to prevent diabetic nephropathy progression.

This paper proposes a single-stage asymmetrical half-bridge fly-back (AHBF) converter with resonant mode using dual-mode control. The presented converter has an integrated boost converter and asymmetrical half-bridge fly-back converter and operates in resonant mode. The boost-cell always operates in discontinuous conduction mode (DCM) to achieve high power factor. The presented converter operates simultaneously using a variable-frequency-controller (VFC) and pulse-width-modulation (PWM) controller. Unlike the conventional single-stage design, the intermediate bus voltage of this controller can be regulated depending on the main power switch duty ratio. The asymmetrical half-bridge fly-back converter utilizes a variable switching frequency controller to achieve the output voltage regulation. The asymmetrical half-bridge fly-back converter can achieve zero-voltage-switching (ZVS) operation and significantly reduce the switching losses. Detailed analysis and design of this single-stage asymmetrical half-bridge fly-back converter with resonant mode is described. A wide AC input voltage ranging from 90 to 264 Vrms and output 19 V/ 120 W prototype converter was built to verify the theoretical analysis and performance of the presented converter.

The principal aim of a spectral observer is twofold: the reconstruction of a signal of time via state estimation and the decomposition of such a signal into the frequencies that make it up. A spectral observer can be catalogued as an online algorithm for time-frequency analysis because is a method that can compute on the fly the Fourier transform (FT) of a signal, without having the entire signal available from the start. In this regard, this paper presents a novel spectral observer with an adjustable constant gain for reconstructing a given signal by means of the recursive identification of the coefficients of a Fourier series. The reconstruction or estimation of a signal in the context of this work means to find the coefficients of a linear combination of sines a cosines that fits a signal such that it can be reproduced. The design procedure of the spectral observer is presented along with the following applications: (1) the reconstruction of a simple periodical signal, (2) the approximation of both a square and a triangular signal, (3) the edge detection in signals by using the Fourier coefficients, (4) the fitting of the historical Bitcoin market data from 2014-12-01 to 2018-01-08 and (5) the estimation of a input force acting upon a Duffing oscillator. To round out this paper, we present a detailed discussion about the results of the applications as well as a comparative analysis of the proposed spectral observer vis-à-vis the Short Time Fourier Transform (STFT), which is a well-known method for time-frequency analysis.

Since the discovery of the human epidermal growth factor receptor 2 (HER2) as an oncogenic driver in a subset of breast cancers and the development of HER2 directed therapies, the prognosis of HER2 amplified breast cancers has increased meaningfully. Next to monoclonal anti-HER2 antibodies and tyrosine kinase inhibitors, the antibody-drug conjugate T-DM1 is a pillar of targeted treatment of advanced HER2-positive breast cancers. Currently, several HER2 directed antibody-drug conjugates are under clinical investigation for HER2 amplified but also HER2 expressing but not amplified breast tumors. In this article, we review the current preclinical and clinical evidence of the investigational drugs A166, ALT-P7, ARX788, DHES0815A, DS-8201a, RC48, SYD985, MEDI4276 and XMT-1522.

In this paper, we study the effect of parasitic channel on electrical characteristics and power consumptions of vertically stacked gate-all-around (GAA) silicon nanosheet (NS) MOSFETs of the bulk and silicon-on-insulator (SOI) substrates. Through deliberate control of the bottom parasitic channel coverage, we systematically assess its influence on DC, AC, and RF characteristics including power consumption. The observed findings highlight a significant differentiation among the bottom parasitic channels: GAA (i.e., control sample with 100% coverage), omega-shaped gate NS (70% and 80% coverages), and FinFET (60% coverage). Compared with the device with a 60% coverage channel, the device with a 100% coverage channel possesses 3520% and 8030% normalized leakage current improvement for both NFET and PFET under the bulk substrate, respectively. Compared with bulk-substrate devices, the SOI-substrate devices further significantly improve the leakage current. Due to enhanced off-state current leakages in the 100% covered bulk-substrate device, the static power demonstrates a notable improvement (about 98.1%), compared to 60% covered devices. Hence, the utilization of a 60% covered channel will result in a degradation of both device and circuit performance. The observation of GAA NS MOSFET indicates that an increase in the bottom parasitic channel coverage ratio leads to a positive impact on power consumption and leakage currents. The examination presented here is useful in the fabrication of stacked GAA NS MOSFETs.

Accurate stock market predictions following earnings reports are crucial for investors. Traditional methods, particularly classical machine learning models, struggle with these predictions because they cannot effectively process and interpret extensive textual data contained in earnings reports and often overlook nuances that influence market movements. This paper introduces an advanced approach by employing Large Language Models (LLMs) instruction fine-tuned with a novel combination of instruction-based techniques and quantized low-rank adaptation (QLoRA) compression. Our methodology integrates ‘base factors’, such as financial metric growth and earnings transcripts, with ‘external factors’, including recent market indices performances and analyst grades, to create a rich, supervised dataset. This comprehensive dataset enables our models to achieve superior predictive performance in terms of accuracy, weighted F1, and Matthews correlation coefficient (MCC), especially evident in the comparison with benchmarks such as GPT-4. We specifically highlight the efficacy of the llama-3-8b-Instruct-4bit model, which showcases significant improvements over baseline models. The paper also discusses the potential of expanding the output capabilities to include a ‘Hold’ option and extending the prediction horizon, aiming to accommodate various investment styles and time frames. This study not only demonstrates the power of integrating cutting-edge AI with fine-tuned financial data but also paves the way for future research in enhancing AI-driven financial analysis tools.