This article addresses the need to know the thermal conductivity in different filaments that this FDM technology uses. Because there are multiple applications that these additive manufacturing products play in the field of thermal insulation. For the study of thermal conductivity, the DTC-25 commercial conductivity measurement bench is used, where the tests will be carried out on a set of seven different materials with 100% fabrication density. From base materials such as acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA), materials of high mechanical and thermal resistance, polyether ether ketone (PEEK) and high-performance polyetherimide thermoplastic (ULTEM), to materials with metal inclusions (aluminum 6061) that would later be subjected to thermal aftertreatments. The study shows how the parts manufactured with aluminum inclusion have a higher thermal conductivity, 0.40 ±0.05 W/m·K, compared to another material, such as TPU, of high mechanical and thermal resistance, with a conductivity of 0.26 ±0.05 W/m·K.

Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal-vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR>TSR>VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology is used to study how the initial residual stress in the blank will cause the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method is applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method is used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters is studied.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

Radiation Fireballs are singular phenomena which involve severe thermal radiation and consequently, they need to be duly assessed and prevented. Although the radiative heat transfer produced by a sphere is relatively well known, the shadowing measures implemented to control the fireball’s devastating effects have frequently posed a difficult analytical instance, mainly due to its specific configuration. In this article, since the usual solving equations for the said cases are impractical, the authors propose a novel graphic-algorithm method that sorts the problem efficiently for different kinds of obstructions and relative positions of the fireball and the defenses. Adequate application of this method may improve the safety of a significant number of facilities exposed to such risks.

Lack of due attention to the orientation of streets and establishment of urban blocks without regard for climatic characteristics and conditions of the environment have an adverse effect on thermal comfort in open urban spaces. Construction of new settlements without taking into account climatic requirements undermines thermal comfort for pedestrians and other users, especially in cold regions. Considering the coldness of the region under study and the significance of the orientation of streets in absorbing radiation and providing heat to outdoor urban spaces, this study investigates the effect of the orientation of streets on microclimatic comfort in one of the residential towns of Hamadan City in Iran. For this purpose, microclimate simulation was performed using ENVI-met software. A residential block with four different orientations (the most common orientations of its surrounding buildings) were simulated in the coldest day of winter and the hottest day of summer. The results suggest that streets have different thermal behavior in different orientations. Orientation affects mean radiant temperature (Tmrt), the duration of exposure to direct sunlight, wind speed, and physiological equivalent temperature (PET), which are all important factors in thermal comfort. Based on these findings, north-south streets in Hamedan receive more radiant temperature during winter compared to other simulated orientations and provide more desirable thermal comfort. The average PET value on a winter day at a point on the north-south passage was 4.5-8 °C warmer than other orientations. In summer, streets with intercardinal orientations (i.e., northeast-southwest and northwest-southeast) provided the lowest PET (about 2 °C cooler than other orientations) and better thermal comfort

The study of hydrothermal travertines contributes to the understanding of the interaction between physico-chemical processes and the role played by microbial mats and biofilms in influencing carbonate precipitation. Three active travertine sites were investigated in Central Italy to identify the types of carbonate precipitates and the associated microbial mats at varying physico-chemical parameters. Carbonate precipitated fabrics at the decimetre- to millimetre-scale and microbial mats vary with decreasing water temperature: a) at high temperature (55-44°C) calcite or aragonite crystals precipitate on microbial mats of sulphide oxidizing, sulphate reducing and anoxygenic phototrophic bacteria forming filamentous streamer fabrics, b) at intermediate temperature (44-40°C), rafts, coated gas bubbles and dendrites are associated with Spirulina cyanobacteria and other filamentous and rod-shaped cyanobacteria, c) low temperature (34-33°C) laminated crusts and oncoids in a terraced slope system are associated with diverse Oscillatoriales and Nostocales filamentous cyanobacteria, sparse Spirulina and diatoms. At the microscale, carbonate precipitates are similar in the three sites consisting of prismatic calcite (40-100 µm long, 20-40 µm wide) or acicular aragonite crystals organized in radial spherulites, overlying or embedded within biofilm EPS (Extracellular Polymeric Substances). Microsparite and sparite crystal size decreases with decreasing temperature and clotted peloidal micrite dominates at temperatures < 40°C, also encrusting filamentous microbes. Carbonates are associated with gypsum and Ca-phosphate crystals; EPS elemental composition is enriched in Si, Al, Mg, Ca, P, S and authigenic aluminium-silicates form aggregates on EPS. This study confirms that microbial communities in hydrothermal travertine settings vary as a function of temperature. Carbonate precipitate types at the microscale do not vary considerably, despite different microbial communities suggesting that travertine precipitation, driven by CO2 degassing, is influenced by biofilm EPS acting as template for crystal nucleation (EPS-mediated mineralization) and affecting the fabric types, independently from specific microbial metabolism.

Coal-fired thermal plants (CTPP) are known to pollute the atmosphere with emission of many greenhouse gases and particulate matter. The power generation from these thermal plants cannot be stopped completely because it forms the backbone of the grid power supply. It is necessary to study the dispersion patterns of pollutants that affect the health of the people. The dispersion patterns are location specific since they depend on local meteorological conditions. In this study, the dispersion of particulate matter (PM) and sulphur dioxide (SO₂) from a CTPP with 275 m high stack are studied under different atmospheric boundary layer (ABL) of neutral, stable and unstable conditions up to a distance of 30 km from the stack. The plume of the PM spreads under all conditions. During some parts of the day, PM settles around the stack while at other times PM keeps suspending in the air for the full distance under study. Sulphur dioxide dilutes to concentrations below the detection limits in about 12-13 km from the stack for neutral and unstable ABL whereas for the stable ABL, the dispersion is up to 30 km. The 24 h weighted average concentration of sulphur dioxide, at 10 m height from the ground, is 14.2 mg/m³ at a distance of 25 kms from the CTPP, which is comparable with the value of 9.2 mg/m³ measured at the Air Quality Stations located around the same distance. Based on the results policy changes that need to be implemented are suggested.

This paper proposes a novel method for optimizing the Cauer-type thermal network model considering both the temperature influence on the extraction of parameters and the errors caused by the physical structure. In terms of prediction of the transient junction temperature and the steady-state junction temperature, the parameters of conventional Cauer-type are modified, and the general method for estimating junction temperature is studied by using the adaptive thermal network model. The results show that junction temperature estimated by adaptive Cauer-type thermal network model is more accurate than that of the conventional model.

Grouting materials with good insulation and reinforcement performance are key factors in solving the temperature control problem of high temperature tunnels using curtain grouting, while existing grouting materials cannot balance their working performance and insulation performance in high-temperature environments. In response to the above issues, this article uses red mud to prepare high ground temperature red mud based grouting materials (RMGS), and conducts tests on the working performance (viscosity, setting time, compressive strength) and insulation performance (thermal conductivity, specific heat capacity) of grouting materials at different temperatures (20, 40, 60, and 80 ℃), and analyzes the variation patterns and micro mechanisms of various characteristics with temperature. The results indicate that an increase in temperature will accelerate the viscosity development and condensation of the grouting material, and lead to a decrease in thermal conductivity and specific heat capacity. In addition, an appropriate temperature can also improve the compressive strength of the material. The increase in temperature will accelerate the hydration reaction rate of the grouting material and the development of internal pores, which is the reason why temperature affects the performance of the grouting material. In engineering applications, cement slurry is suitable for static water grouting, cement-sodium silicate slurry is suitable for dynamic water grouting, and RMGS is suitable for high-temperature tunnel grouting.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

Instead of simplified steady-state models, with modern computers, one can solve the complete aero-thermodynamics happening in gas turbine engines. In the present article, we describe a mathematical model and numerical procedure to represent the transient response of a PT6A gas turbine engine operating at off-design conditions. The aero-thermal model consists of a set of algebraic and ordinary differential equations that arise from the application of the mass, linear momentum, angular momentum, and energy balances in each engine's component. The solution code has been developed in Matlab-Simulink using a block-oriented approach. Transient simulations of the PT6A engine start-up have been carried out by changing the original Jet-A1 fuel with biodiesel blends. Time plots of the main thermodynamic variables are shown, especially those regarding the structural integrity of the burner. Numerical results have been validated against reported experimental measurements and GasTurb simulations. The computer model has been capable to predict acceptable fuel blends, such that the real PT6A engine can be substituted to avoid the risk of damaging it.

The welding and construction processes of H-type thick-plate-bridge steel involve complex multi-pass welding processes, which is difficulty to ensure its welding performance. Accordingly, it is crucial to explore the inherent correlation among the welding processes parameters and welding quality, and applied it into the welding robots, eliminating the instability from manual welding. In order to improve the welding quality, the GMAW (Gas Metal Arc Welding) welding process parameters are simulated using the Q345qD bridge steel flat joint model. Four welds with X-shaped grooves are designed to optimize the parameters of welding current, welding voltage, and welding speed. The optimal welding process parameters are investigated through thermal-elastic-plastic simulation analysis and experimental verification. The results indicate that when the welding current is set to 230A, the welding voltage to 32V, and the welding speed to 0.003m/s, the maximum deformation of the welded plate is 0.52mm, with a maximum welding residual stress of 345MPa. Both the simulation results of multi-pass welding and experimental tests meet the welding requirements, as they show no excessive stress or strain. These parameters can be applied into building large steel frame bridges with welding robots, improving the quality of welded joints.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

This manuscript deals with the cavitation erosion resistance of low-velocity oxy-flame (LVOF) sprayed Al2O3–40%TiO2/NiMoAl cermet coatings, a new functional application of cermet coatings. The aim of the study was to investigate the cavitation erosion mechanism and determine the effect of feedstock powder ratio (Al2O3–TiO2/NiMoAl) of LOVF cermet coatings on their cavitation erosion resistance. As-sprayed coatings were investigated for roughness, porosity, hardness, Young’s modulus. Microstructural characteristics of the cross-section and the surface of as-sprayed coatings were examined by light optical microscopy (LOM) and scanning electron microscopy (SEM) equipped with the EDS and XRD methods. Coatings cavitation tests were conducted in accordance with the ASTM G32 standard with usage of reference samples made from steel, copper and aluminum alloys. Cavitation erosion resistance was measured by weight and volume loss, and normalised cavitation erosion resistance was calculated. Surface eroded due to cavitation was examined in successive time intervals by LOM and SEM-EDS. On the basis of coating properties and cavitation investigations, a phenomenological model of the cavitation erosion of Al2O3–40%TiO2/NiMoAl cermet coatings was elaborated. General relationships between their properties, microstructure and cavitation wear resistance were established. The Al2O3–40%TiO2/NiAlMo composite coating containing 80% of ceramic powder has a higher cavitation erosion resistance than the reference aluminium alloy.

This study examines the effects of particle size and heat pipe angle on the thermal effectiveness of a cylindrical screen mesh heat pipe using silver nanoparticles as the test substance. The experiment investigates three different particle sizes (30nm, 50nm, and 80nm) and four different heat pipe angles (0°, 45°, 60°, and 90°) on the heat transmission characteristics of the heat pipe. The results show that the thermal conductivity of the heat pipe increased with an increase in heat pipe angle for all particle sizes, with the highest thermal conductivity attained at a 90° heat pipe angle. Furthermore, the thermal resistance of the heat pipe decreased as the particle size decreased for all heat pipe angles. The thermal conductivity measurements of the particle sizes - 30, 50, and 80 nm - were 250 W/mK, 200 W/mK, and 150 W/mK, respectively. The heat transfer coefficient values for particle sizes 30nm, 50nm, and 80nm were 5500 W/m2K, 4500 W/m2K, and 3500 W/m2K, respectively. The study also found that the heat transfer coefficient increased with increased heat pipe angle for all particle sizes, with the highest heat transfer coefficient obtained at a 90° heat pipe angle.

Medical institutions, where several patients are treated and medical workers engaged, are always exposed to secondary viral and bacterial infections. It is critical to prevent infection transmission by indirect as well as direct contact through air or splash. The infections of most diseases can be transmitted through the air. HEPA filters installed in air conditioning equipment are used to prevent infection transmission through air in medical institutions, but air circulation takes a long time in a large space. Virus and bacteria smaller than 0.3 μm cannot be removed by the HEPA filter; hence, those microbes remain alive throughout the air ventilation. A plasma sterilizer has the capability to provide environmental friendly sterilization by employing reactive oxide species and reactive nitrogen species at a low cost. We developed an excellent plasma sterilizer by using a non-thermal atmospheric-pressure biocompatible plasma (NBP). Ozone concentration in plasma sources has been derived by Kuhn et al. [1]. The diffusion coefficients inside (D₀) and outside (D₁) the plasma sterilizer have been calculated to be 0.0641 m² s^-1 and 0.717 m² s^-1, respectively. To sustain high O₃ concentrations over 121 ppm inside the plasma source and low O₃ concentrations below 0.05 ppm outside the sterilizer, it is necessary to keep O₃ concentrations at the exit of plasma sterilizer below 0.28 ppm. so that diffusion coefficient D₁ has been designed to be as large as 11 times of D₀.

Almost all single-family detached house in Canada consume huge electricity for space heating and domestic hot water (DHW) purposes. There are many possibilities to design an energy-efficient house. A solar water heating system can be used for domestic water and space heating. Water temperature can be kept constant always by connecting a heat pump or oil burner because solar energy is intermittent. Proper and optimized solar photovoltaic and collector design, tank design, heat pump selection, house insulation, total demand calculation in each section are essential. Energy-Efficient house design has been proposed with water heating and space heating system and compared with the existing system, solar PV based systems, and solar collector based system. The tracking and non-tracking based solar thermal collector based and the solar photovoltaic based system has been compared in this paper and investigate the suitable one for practically applicable and acceptable by the people. Simulation has been done by using the PolySun software. It found that by implementing the proposed PV based system with tracking is highly suitable considering lower cost, high output power, flexibility, easy installation.

Spinal metastatic tumors are common and often cause debilitating symptoms. Image-guided percutaneous thermal ablation (IPTA) has gained significant recognition in managing spinal column tumors due to its exceptional precision and effectiveness. Conventional guidance modalities, including computed tomography, fluoroscopy, and ultrasound, have been important in targeting spinal column tumors while minimizing harm to adjacent critical structures. This study presents a novel approach utilizing a fusion of Cone Beam Computed Tomography with Magnetic Resonance Imaging to guide percutaneous thermal ablation for four patients with secondary spinal column tumors. The visual analog scale (VAS) evaluated procedure effectiveness during an 18-month follow-up. Percutaneous vertebroplasty was performed in two cases, and a thermostat was used during all procedures. Imaging was performed using the Stealth Station navigation system Spine 8 (SSS8) and a 1.5T MRI machine. The fusion of CBCT with MRI allowed precise tumor localization and guidance for thermal ablation. Initial results indicate successful tumor ablation and symptom reduction, emphasizing the potential of CBCT-MRI fusion in spinal column tumor management. This innovative approach is promising in optimizing therapy for secondary spinal column tumors. Further studies are necessary to validate its efficacy and applicability.

Many buildings built before the energy performance regulations are in a situation of thermal discomfort and energy inefficiency. The creation of intelligent environments advances towards new opportunities, based on real-time monitoring and on the development of sensors and technologies. Furthermore, the standards for building automation and electronic systems enable interoperability and interconnection between control devices and systems. The application of soft computing has significantly improved the energy efficiency, however, requires prior assessment to design the automation functions. Temperature, humidity, air quality, occupancy and energy consumption are the most common measured parameters, but the relationship with other operational variables such as occupancy or some building states remains as a research challenge. This article presents a methodology to develop the automatization of an existing large public building. The methodology consists of three stages: 1. Assessment and diagnosis to set appropriate actions using EN ISO 52120-1. 2. EN 50090 for open communication networks, and EN ISO 52120-1 to assign the technical building management. 3. System control deploying of low-cost and low-consumption input and output devices. It has been proved that it is possible to effectively automate an obsolete building with a low cost, open source system that can be easily applied in other buildings.

Although the majority of mobile phone (MP) users do not attribute adverse effects on health or well-being to MP-emitted radiofrequency (RF) electromagnetic fields (EMFs), the exponential increase in the number of RF devices necessitates continuing research aimed at the objective investigation of such concerns. In this work, we investigate the effects of acute exposure from Long Term Evolution (LTE) MP EMFs on thermal pain threshold in healthy young adults. We use a protocol that was validated in a previous study in a capsaicin-induced hyperalgesia model, and was also successfully used to show that exposure from an RF source mimicking a Universal Mobile Telecommunications System (UMTS) MP led to mildly stronger desensitization to repeated noxious thermal stimulation relative to the sham condition. Using the same experimental design, we did not find any effects of LTE exposure on thermal pain threshold. The present results are in accordance with previous evidence suggesting that effects are likely to be placebo/nocebo effects and are unrelated to the brief acute LTE EMF exposure itself. The fact that this is dissimilar to our previous results on UMTS exposure implies that RF modulations might differentially affect pain perception, and points to the necessity of further research in the topic.

This paper presents a calibration and thermal compensation method that aims to minimize cost and processing time while maintaining high accuracy. First, the number of positions to perform the calibration procedure is optimized, and then, based on this optimized calibration number, thermal compensation is performed, which is necessary for environments with large temperature variations, since calibration parameters change at different temperatures. The calibration procedures and algorithms were experimentally validated on marketed accelerometers. Based on the optimized calibration method, the calibrated results have been obtained nearly 100 times improvement. Thermal drift calibration experiments on the triaxial accelerometer show that the thermal compensation scheme in this paper can effectively reduce drift in the temperature range of -40°C to 60°C. The temperature drifts of x- and y-axes are reduced from -13.2 and 11.8 mg to -0.9 and -1.1 mg, respectively. The z-axis temperature drift is reduced from -17.9 to 1.8 mg. We have conducted various experiments on the proposed calibration method and demonstrated its capacity to calibrate the sensor frame error model (SFEM) parameters. Therefore, the MEMS sensors calibrated in this paper have certain engineering application values for tilt measurement.

As a new kind of highly compact and efficient micro-channel heat exchanger, printed circuit heat exchanger (PCHE) is a promising candidate satisfying the heat exchange requirements of liquefied natural gas (LNG) vaporization at low and high pressure. The effects of airfoil fin arrangement on heat transfer an flow resistance were numerically investigated using supercritical liquefied natural gas (LNG) as a working fluid. The thermal properties of supercritical LNG were tested by utilizing a REFPROF software database. Numerical simulation was performed using FLUENT. The inlet temperature of supercritical LNG was 121 K,and its pressure was 10.5MPa. The reference mass flow rate of LNG was set 1.22 g/s for the vertical pitch L_v = 1.67 mm and the staggered pitch L_s = 0 mm, with the Reynolds number of about 3750. The SST k-ω model with enhanced wall treatment was selected by comparing with the experimental data. The airfoil fin PCHE had better thermal-hydraulic performance than that of the straight channel PCHE. Moreover, the airfoil fins with staggered arrangement displayed better thermal performance than that of the fins with parallel arrangement. The thermal-hydraulic performance of airfoil fin PCHE was improved with increasing L_s and L_v. Moreover, L_v affected on the Nusselt number and pressure drop of airfoil fin PCHE more obviously. In conclusion, a sparser staggered arrangement of fins showed a better thermal-hydraulic performance in airfoil fin PCHE.

Given its exceptional attributes, aerogel is viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porousness, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textile sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogel formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multi-functionality of cellulose-based aerogels in the textile industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Abstract: The species composition, the structure of phytoplankton communities, hydrochemical parameters in the artificial cooling reservoir of one of the largest thermal power plants (TPP) in the north-east of Europe in the Pechora River basin, Komi Republic were studied in the ice-open period in June and August. Altogether 81 species of algae and cyanobacteria was revealed with the last one predominated. Among cyanobacteria and algae (Bacillariophyta, Chlorophyta), indicators of water quality were found. Assessment of water quality according to the species composition and abundance of indicator phytoplankton species showed that the waters of the Pechorskoe Reservoir can be at-tributed to the III class of water quality, beta-mesosaprobic self-purification zone, with water quality of satisfactory purity, retaining the ability to self-purify. An increase in the diversity of plankton communities and high values of their abundance and biomass under the influence of the warming effect of TPP water outlet were noted and revealed its spatial distribution over the reservoir surface. The plankton of the northern reservoir under the influence of warm waters indicates a slight in-crease in the trophic status of the studied water body, which is also confirmed by the data of hydrochemical analysis. Ecological mapping for the chemical and biological variables as well as pollution indices over the water area of the reservoir was carried out. The results obtained can be used to make forecasts of changes in the phototrophic biota of small northern water bodies under the conditions of climate change.

As a widely used plastic, the aging and degradation of polyethylene (PE) are inevitable problems, whether the goal is to prolong the life of PE products or address the issue of white pollution. Molecular simulation is a vital scientific tool in elucidating the mechanisms and processes of chemical reactions. To obtain the distribution and evolution process of PE's thermal oxidation products, this work employs the self-consistent charge density functional tight binding (SCC-DFTB) method to perform molecular simulations of the thermal oxidation of PE with different crystallinity and branched structures. We discovered that crystallinity does not affect the thermal oxidation mechanism of PE, but higher crystallinity makes PE more susceptible to cross-linking and carbon chain growth, reducing the degree of PE carbon chain breakage. The branched structure of PE results in differences in pore size between the carbon chains, with larger pores leading to a concentrated distribution of O2 and free radicals subsequently formed. The breakdown of PE is slowed down when free radicals are localized in low-density regions of the carbon chain. The specifics and mechanism of PE's thermal oxidation are clearly revealed in this paper, which is essential for understanding the process in-depth and for the development of anti-aging PE products.

This paper focuses on the comparative analysis of lithium-ion batteries (LIB) thermal management with aim to maintain working temperature in the range 15 ℃ – 35 ℃. This is to prevent thermal runaway and high temperature gradients. The proposed approach is to employ the biodiesel, situated inside the diesel/LIB powered hybrid electric vehicle, to supply as fuel and coolant. A 3S2P LIB module is simulated using Ansys-Fluent CFD software tool. The system without a coolant shows that LIB has exceeded the optimum maximum temperature, which leads to shortened life-cycle and poor performance. Four fatty acid methyl ester biodiesels are used as coolants, namely palm, karanja, jatropha, and mahua oils. When compared with conventional methods of cooling, using air and 3M Novec liquid, the palm biodiesel coolant proves to be the best option to maintain LIB temperature within the optimum working range. With the use of palm biodiesel, the system is estimated to lightweight the BTMS by 43%, compared to the case when 3M Novec is used to maintain the same temperature range.

Artificial roughness applied to the Solar Air Heater (SAH)’s absorber plate is a popular technique to increase its total-thermal efficiency (η_(t-th)). In this paper, the influence of geometrical parameters of V-down ribs attached below the corrugated absorbing plate of SAH on the η_(t-th) has been examined. The impacts of key roughness parameters, including relative pitch p⁄e (6-12), relative height e⁄D (0.019-0.043), angle of attack α (30°-75°), and Re (1000-20000), are examined under real weather conditions. The SAH η_(t-th) roughened by V-down ribs is predicted using an in-house developed conjugate heat transfer numerical model. It has been shown that the maximum SAH η_(t-th) is 78.8%, predicted under steady-state conditions of Re = 20000, solar irradiance G =1000 W/m2, p/e = 8, e/D = 0.043, and angle =60. That is 15.7% more efficient than that of the default smooth surface. Under real weather condition, the η_(t-th) of the roughened SAH with single and double glass covers are 17.7% and 20.1%, respectively, higher than those of smooth SAH.

Transparent electrodes (TEs) made of metallic nanowires, such as Ag, Au, Cu, and Ni, have attracted rising attention for several reasons: 1) they can act as a substitute for tin oxide-based TEs such as indium-tin oxide (ITO) and fluorine-doped tin oxide (FTO); 2) various methods exist for fabricating such TEs such as filtration, spraying and meyer bar coating; 3) greater compatibility with different substrates can be achieved due to the variety of fabrication methods; and 4) extra functions in addition to serving as electrodes, such as catalytic abilities, can be obtained due to the metals that compose the TEs. There are a large number of applications for TEs, ranging from electronics and sensors to biomedical devices. This short review is a summary of recent progress, mainly during the past five years, on silver nanowire-based TEs. The focus of the review will be on theory development, mechanical, chemical and thermal stability and optical properties. The many applications of TEs are outside the scope of this review.

The StarDICE experiment strives to establish an instrumental metrology chain with a targeted accuracy of 1 mmag in griz bandpasses to meet the calibration requirements of next-generation cosmological surveys. Atmospheric transmission stands out as a significant source of systematic uncertainty. Specifically, gray extinction induces spurious variations of photometric fluxes. We propose a solution relying on an uncooled long-wave infrared thermal camera to evaluate it. This type of camera can provide real-time insights into atmospheric conditions and detect cirrus clouds. However, achieving accurate measurements with thermal imaging systems necessitates prior calibration due to the influence of temperature-induced effects, which compromise their spatial and temporal precision. Moreover, these systems cannot provide scene radiance values in physical units by default. This study introduces a new calibration process utilizing a tailored forward modeling approach. The method is applied to an uncooled FLIR Tau2 thermal camera. It incorporates sensor, housing, flat-field support, and ambient temperatures, along with raw digital response, as input data. Experimental measurements are conducted inside a climatic chamber, with the camera imaging a thermoregulated blackbody source. Results demonstrate the calibration effectiveness, achieving precise radiance measurements with a temporal pixel root-mean-square error (RMSE) of 0.09 W/m2/srand residual spatial noise of 0.03 W/m2/sr.

Objective: The key to the success of pedicled skin flaps in the head and neck region is preserved perfusion. The use of thermal imaging can provide an indirect indicator of tissue perfusion, which consecutively would be of interest for perioperative prediction of the viability. The effectiveness of thermal imaging has already been demonstrated for assessing pedicled and free flaps [1]. This work investigates the implementation of SBTI as a noninvasive and cost-efficient method in clinical practice for predicting the vitality and perioperative monitoring of pedicled skin flaps in head and neck surgery. Methods: The FLIR One Pro camera was used for this pilot study (Teledyne FLIR LLC, Wilsonville, Oregon, United States). It is a multispectral camera that contains a near-infrared camera unit with a resolution of 160 x 120 pixels, a temperature range of 0 ° - 400 °C, and a thermal resolution of 70 millikelvin. For the study, after implementing the system, n = 11 skin flaps were photographed by SBTI (n=44) after marking (T1), after elevation (T2), after completed surgery (T3), and 24 hours postoperatively (T4), and the outcome was assessed clinically in correlation after one week by one surgeon. Results: The pedicled skin flaps examined all showed a preserved, uniform thermal image signature peri- and postoperatively for time points T1-4. This corresponded to a good postoperative result regarding the vitality of the tissue transfer in the clinical assessments 24 hours and one week postoperatively. Conclusion: The acquisition of a continuously obtained thermal image signature as a surrogate marker for preserved tissue perfusion by SBTI proved simple, inexpensive, noninvasive, and efficient in the present sentinel study. The application of SBTI has been primarily investigated in identifying perforators in large pedicled or free flaps. [2, 3] The concordance of the obtained thermal image signature with a positive clinical outcome suggests that the presented method is also suitable for perioperative prognostic statements on postoperative flap vitality in pedicled skin flaps and for monitoring those during surgery. Further studies are necessary for the implementation of this method in clinical practice to support the surgeon's intraoperative decision-making in the future.

We consider a real scalar field in de Sitter background and compute its thermal propagators. We propose that in a dS/CFT context, non-trivial thermal effects as seen by an `out' observer can be encoded in the anomalous dimensions of the d=3 Ising model. One of these anomalous dimensions, the critical exponent eta, fixes completely a number of cosmological observables, which we compute.

Thermal comfort is extremely important in architecture, especially in environments with more people spending longer on studies or intellectual activities. This research describes a case study to investigate university buildings' energy and thermal performance as a part of the ANEEL program. Due to this importance, and the need to save energy in Brazilian public buildings, the ANEEL-the Brazilian Energy Electricity Regulatory Agency, launched 2016 a national program focusing on energy efficiency in public universities around the country. University offices and classrooms require high intellectual effort; thus, environmental comfort is critical for maintaining its users' physical and mental health. This study included a pre-diagnosis of the performance of the envelope, lighting, and air conditioning systems and a survey about the quality of the environments from the users' point of view. The Prescriptive Method of the Brazilian Labeling Program (PBE) for Commercial, Service, and Public Buildings (RTQ-C) assessed the building performance. Statistical analysis was applied to correlate the quality and thermal preference of the users from the PMV/PPD. The results showed a high rate of thermal discomfort in both environments of the studies, even when using air conditioning.

The study of energy sources has been an awareness of the modern world due to constraints on the current energy worldwide supply chain. The complexity of the theme as well as the consciousness of finite sources also the need of saving energy has become a priority. Although many papers have moved in this direction there is no record of papers studying the variables in a house heating system, which represents the highest energy consumption in many cold countries. This paper explores the energy-saving theme by studying the main variables present in houses’ heating systems in the winter season in cold countries like Canada, Russia, Norway, Iceland, Finland, etc. By using a novel combination of numerical thermal simulation by COMSOLTM and statistical analysis by MiniTabTM , it was possible to design an efficient thermal distribution in a house with the variables of the system by determining their significance and interaction qualitatively.

(1) Background: This article presents a study that aims to provide a precise understanding of the temperature distribution within a Whole-Body Cryostimulation (WBC) chamber, whether it is empty or occupied by one or several individuals.; (2) Methods: The study employs a mixed numerical and experimental approach, utilizing simplified Computational Fluid Dynamics (CFD) simulations and an experimental analysis that employs thermocouples to determine the 3D thermal field in actual conditions.; (3) Results: The results reveal a non-negligible temperature difference between the setpoint and actual temperature in the middle of the cryochamber. Furthermore, it is shown that the presence of individuals inside the chamber results in both an average temperature rise and a more heterogeneous thermal behavior, which appear to be associated with the number of individuals present.; (4) Conclusions: The findings of this study emphasize the need for further research to establish temperature guidelines and standardize measurement methods for effective WBC treatment.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

The problem of water drinking supply is very important in the world, especially for developing countries, in particular Algeria. In this work we propose to study a distillation system based on solar energy process using an artificial intelligence approach in order to enhance the performance and the daily production. For this purpose, a conventional solar still and capillary film solar still was used. The operating parameters of the two distilleries are analyzed and the neural network approach was used to predict the performance through the amount of distillate, solar radiation and ambient temperature. The sensitivity between the operating parameters of the solar still for two case have been studied through the artificial neuron network model. The obtained results are promising, analyzed and discussed.

The deep geothermal industrial project at Soultz-sous-Forêts is located in the Upper Rhine Graben, France. As part of the MEET project, this study aims to evaluate the possibility of extracting higher amounts of energy from the existing industrial infrastructure. To achieve this objective, the effect of reinjecting fluid at lower temperature than the current fluid injection temperature of 70 ℃ was modelled and the drop in the production wellhead temperature for 100 years of operation was quantified. Two injection-production rate scenarios were considered and compared for their effect on overall production wellhead temperature. For each scenario, reinjection temperatures of 40 ℃, 50 ℃ and 60 ℃ were chosen and compared with the 70 ℃ injection case. For the lower production rate scenario, the results show that the production wellhead temperature is approximately 1-1.5 ℃ higher than for the higher production rate scenario after 100 years of operation. In conclusion, no significant thermal breakthrough has been observed with the applied flow rates and lowered injection temperatures even after 100 years of operation.

Metal foams are widely studied as possible tools for the enhancement of heat transfer from hot bodies. The basic idea is that a metal foam tends to increase significantly the heat exchange area between the hot solid body and the external cooling fluid. For this reason, this class of porous materials are considered as good candidates for an alternative to finned surfaces, with different pros and cons. Among the pros, we mention the generally wider area of contact between solid and fluid. Among the cons is the difficulty of producing different specimens with the same inner structure, with the consequence that their performance may be significantly variable. This paper will offer a survey of the literature with a focus on the main heat transfer characteristics of the metal foams. Then, a numerical simulation of the heat transfer at the pore scale level for an artificial foam with a spatially periodic structure will be discussed. Finally, these numerical results will be employed to assess the macroscopic modelling of the flow and heat transfer in a metal foam.

The temperature of the indoor environment is important for health and wellbeing especially at the extremes of age. The study aim was to undertsand the relationship between self-reported thermal sensation and extremity skin temperature in care home residents with and without dementia. The Abbreviated Mental Test (AMT) was used to discriminate residents to two categories, those with and those without dementia. After acclimatisation, measurements included: tympanic membrane temperature, thermal sensation rating followed by infrared thermal mapping of non-dominant hand and forearm. Sixty-nine afebrile adults (60-101 years of age) were studied in groups of two to five, in mean ambient temperatures of 21.4^oC-26.6^oC (median 23.6^oC). Significant differences were observed between groups; thermal sensation rating (p=0.02), tympanic temperature (p=0.01), fingertip skin temperature (p=0.01) and temperature gradients; fingertip-wrist p=0.001 and fingertip-distal forearm, p=0.001.

The experimental determination of the relative biological effectiveness of thermal neutron factors is fundamental in Boron Neutron Capture Therapy. Present values have been obtained using mixed beams consisting of both neutrons and photons of various energies. A common weighting factor has been used for both thermal and fast neutron doses, although such an approach has been questioned. At the nuclear reactor of the Institut Laue-Langevin a pure low-energy neutron beam has been used to determine thermal neutron relative biological effectiveness factors. Different tumor cell lines, corresponding to glioblastoma, melanoma, and head and neck squamous cell carcinoma, and non-tumor cell lines (lung fibroblast and embryonic kidney) have been irradiated using an experimental arrangement designed to minimise neutron-induced secondary gamma radiation. Additionally, the cells were irradiated with photons at a medical linear accelerator, providing reference data for comparison with that from neutron irradiation. Survival and proliferation were studied after irradiation, yielding the Relative Biological Effectiveness corresponding to the damage of thermal neutrons for the different tissue types.

Shale gas production is associated with significant usage of fresh water and discharge of wastewater. Consequently, there is a necessity to create the proper management strategies for water resources in shale gas production and to integrate conventional energy sources (e.g., shale gas) with renewables (e.g., solar energy). The objective of this study is to develop a design framework for integrating water and energy systems including multiple energy sources, cogeneration process, and desalination technologies in treating wastewater and providing fresh water for shale gas production. Solar energy is included to provide thermal power directly to a multi-effect distillation plant (MED) exclusively (to be more feasible economically) or indirect supply through a thermal energy storage system. Thus, MED is driven by direct or indirect solar energy, and excess or direct cogeneration process heat. The proposed thermal energy storage along with the fossil fuel boiler will allow for the dual-purpose system to operate at steady-state by managing the dynamic variability of solar energy. Additionally, electric production is considered to supply a reverse osmosis plant (RO) without connecting to the local electric grid. A multi-period mixed integer nonlinear program (MINLP) is developed and applied to discretize operation period to track the diurnal fluctuations of solar energy. The solution of the optimization program determines the optimal mix of solar energy, thermal storage, and fossil fuel to attain the maximum annual profit of the entire system. A case study is solved for water treatment and energy management for Eagle Ford Basin in Texas.

High redshift blazars are among the most powerful objects in the Universe. Although they represent a significant fraction of the extragalactic hard X-ray sky, they are not commonly detected in gamma-rays. High redshift (z>2) objects represent <10 per cent of the AGN population observed by Fermi so far, and gamma-ray flaring activity from these sources is even more uncommon. The characterization of the radio-to-gamma-ray properties of high redshift blazars represents a powerful tool for the study of the energetics of such extreme objects and the Extragalactic Background Light. This contribution will present results of multi-band campaigns, from radio to gamma-rays, on PKS 0836+710, PKS 2149-306, and TXS 0536+145. The latter is the highest redshift detection of a flaring gamma-ray blazar so far. At the peaks of their respective flares these sources reached an apparent isotropic gamma-ray luminosity of about 10^50 erg/s, which is comparable with the luminosity observed from the most powerful blazars. The physical properties derived from the multi-wavelength observations of these sources are then compared with those shown by the high redshift population.

Hazelnut, pistachio and cashew are tree nuts with health benefits but also with allergenic properties being prevalent food allergens in Europe. The allergic characteristics of these tree nuts after processing combining heat, pressure and enzymatic digestion were analyzed through in vitro (Western blot and ELISA) and in vivo test (Prick-Prick). In the analyzed population, the patients sensitized to Cor a 8 (nsLTP) were predominant over those sensitized against hazelnut seed storage proteins (Sprot, Cor a 9 and 14), which displayed higher IgE reactivity. The protease E5 effectively hydrolyzed proteins from hazelnut and pistachio, while E7 was efficient for cashew protein hydrolysis. When combined with pressured heating (autoclave and Controlled Instantaneous Depressurization (DIC)), these proteases notably reduced the allergenic reactivity. The combination of DIC treatment before enzymatic digestion resulted in the most effective methodology to drastically reduce or indeed eliminate the allergenic capacity of tree nuts.

Herein, we report on a giant thermoelectric figure of merit of a non-degenerate fluorine-doped single-walled carbon nanotube (FSWCNT) using a tractable analytical approach and the phonon lattice Boltzmann model (LBM). We investigate the influence of the doping concentration, and the overlapping integrals on the ZT. The ZT and the temperature range of operation can be tuned using the doping (impurity) concentration and the overlapping integrals, respectively. The lattice thermal conductivity obtained using the phonon LBM was calculated to be 107.2 W/mK which yielded a ZT greater than 20. Interestingly, the ZT obtained is higher than what has been reported in superlattices, (ZT~1.4) and superlattice nanowire, (ZT~ 4) at 300 K, making FSWCNT a potential candidate for thermoelectric applications.

There is an international concern for reducing energy consumption and protecting environment by application of circular economy principles in the construction industry. The thermal resistance of concrete plays a significant role in the energy efficiency of a building, and this can be improved by using concrete products with high thermal resistance. This study analyzes the influence of perlite, as an addition, on the physico-mechanical properties of concrete, with the aim of identifying perlite concrete products that will respond to the improvement of the heat transfer resistance of the building envelope. The study examines the effect of replacing different amounts of concrete aggregates with perlite in percentages of 10%, 20%, 30% and 100%. The results show that the replacement of sand with perlite improves the thermal performance of concrete, but its mechanical properties are negatively affected. The research carried out highlighted that perlite can be successfully introduced in the production of concrete blocks used for external non-bearing walls pannels, the outstanding feature being the reduction of energy consumption in buildings. Overall, the paper identifies an efficient and environmentally friendly way of using perlite in the construction industry, improving the energy performance of buildings, and reducing the environmental impact of construction wastes.

Air pollution is responsible for any adverse effects on human beings. Thermal discomfort, on the other hand, is able to overload the human body and eventually provoke health implications due to the heat imbalance. Methods: The aim of the present work is to study the behavior of two bio-climatic indexes and statistical characteristics of the air quality index for Sofia city - the capital of Bulgaria for the period 2008 - 2014. The study is based on WRF-CMAQ model system simula-tions with a spatial resolution of 1 kilometer. The air quality is estimated by the air quality index, taking into account the influence of different pollutants and the thermal conditions by two indi-ces, respectively, for hot and cold weather. Results: It was found that half of the heat and cold index categories are present in the simulations. Their distribution has some spatial features. All air quality categories are present in the domain, with dominance only of the O3 and PM10. Conclu-sions: It was found that Sofia is not so hot and air polluted place, but in some situations, people have to have some concerns when intend to be outdoors for a prolonged time.

The motivation of this work is to investigate experimentally the influence of non-thermal plasma (NTP) application on the reaction kinetics of atmospheric pressure steam gasification of charcoal using a thermostatically controlled drop tube reactor. A gliding-arc generator provides about 1 kW electrical power NTP. For comparison thermal gasification is investigated under comparable flow and specific energy input conditions providing additional heat to the steam. Optical temperature measurement 20 cm flow down of the NTP zone is utilized to characterize the specific enthalpy of the reactive flow. The composition of produced syngas is measured by a gas analyzer and used for the calculation of gas flow rates. The results show a NTP-enhancement on the production of individual syngas components (H2, CO, CH4), especially on hydrogen production by around 39%. The syngas-based carbon conversion and hydrogen release are calculated from the carbon and hydrogen balance between the correspondent content in syngas and in the feedstock. The NTP promoted the carbon conversion and hydrogen release by 25% and 31%, respectively. The first-order reaction kinetics are determined by data-fitting in an Arrhenius diagram. The plasma enhanced the reaction rate coefficients by 27%. Based on experimental results and other literature, possible plasma-induced reactions are proposed.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

This paper reveals the physical properties of Jeffery nanofluid flow past a moving plate embedded in porous medium under the existence of radiation and thermal diffusion. The analysis is carried out in three cases of moving plate, namely stationary plate λ = 0, forth-moving plate λ = 1, back-moving plate λ = −1. Finite difference method is applied to solve the governing equations of the flow and pointed out the variations in velocity, temperature and concentration with the use of graphical presentations. The impact of several parameters on local skin friction, Nusselt number and Sherwood number is also noticed and discussed. Enhancement of velocity is observed under the impact of Jeffery parameter for the cases of stationary plate and back-moving plate, whereas reverse nature is found in the case of forth-moving plate. The velocity enhances as the values of porosity parameter increases for the case of stationary plate and forth-moving plate but a reverse nature is noticed in the case of back-moving plate.

The path towards decarbonization requires a progressive adaptation of all refrigeration systems, but only stationary ones have been intensely studied to improve their environmental performance. However, refrigerated transport is a vital piece of the cold chain, and it must be considered in the green transition. In this paper, we propose a model for a hybrid refrigerated van that includes photovoltaic panels and electric batteries to decrease total greenhouse gas emissions from the engine. Thermal, electrical, and battery sub-models are considered and integrated into the comprehensive hybrid solar-powered refrigerated van model. Different technologies are compared in economic terms, including Lithium and Lead-acid batteries and three different types of photovoltaic panels. The model was validated regarding van fuel consumption, showing a 4% deviation. Single and multiple delivery scenarios are considered to assess the energetic, economic, and environmental benefits. Monthly CO2,e emissions could be reduced to 20% compared to a standard refrigerated van. Despite the environmental benefits provided by this sustainable solution, the payback period is still too long (above 20 years) because of the necessary investment to adapt the vehicle and considering fuel and electricity prices currently.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Heating stage accounts for the largest proportion of building carbon emissions. In order to figure out heating situations of rural residential building in Gansu Province, Gannan region was selected to carry out on-site survey on heating condition including heating mode, energy used for heating, heating fees, residents’ satisfaction on heating and thermal environment of typical building. The results showed that local rural residents burnt scattered coal for heating with primitive heating stove with high heating cost and low efficiency, causing low air temperature and high heating fees. Besides carbon emissions caused by heating reached 5743.28 kgCO2em-2, Several strategies for improving the heating effect and reducing carbon were proposed taking economic benefits into consideration limited by rural economic development. A parameter of reduced carbon emissions per investment input was proposed to evaluate the carbon reduction strategies. Results showed that Biomass was the most economical way to reduce the carbon emissions, followed by thermal insulation design, natural gas furnace and air source heat pumps for heating, and it was not reasonable to blindly increase building insulation to reduce building carbon emissions. The optimum energy efficiency was 55% in Gannan. The results provided reference for building low-carbon design in rural areas, helped achieving low carbon goal with low investment.

In this experimental report the biocompatibility of elastomeric scaffold structures made via stereolithography employing table-top 3D printer (Ember, Autodesk) and commercial resin FormLabs Flexible (FormLabs) was studied. The samples were manufactured using standard printing and development protocol, which is known to inherit cytotoxicity due to remaining non-polymerized remaining monomers, despite the polymerized material being fully biocompatible. Additional steps were taken to remedy this problem: the fabricated structures were soaked in isopropanol and methanol for different conditions (temperature, duration) in order to leach out the non-polymerized monomers. Also printed structures were UV exposed to assure maximum polymerization degree of the material. Post-processed structures were seeded with myogenic stem cells and the number of live cells was evaluated as an indicator for the material biocompatibility. The straightforward post-processing protocol enhances the biocompatibility by 7 times after 7 days soaking in isopropanol and methanol and is comparable to control (glass and polystyrene) samples. This proposes the approach as a novel and simple method to be widely applicable for dramatic cytotoxicity reduction of optically 3D printed micro-/nano-scaffolds for biomedical applications.

Nanocomposites of cyanate ester resin (CER) filled with three different reactive amino-functionalized polyhedral oligomeric silsesquioxane (POSS) were synthesized and characterized. The addition of a small quantity (0.1 wt.%) of amino-POSS chemically grafted to the CER network led to increasing thermal stability of CER matrix. A significant increase of the glass transition temperature, Tg (DSC data), and the temperature of α relaxation, Tα (DMTA data), by 45-55 оС of CER matrix with loading of nanofillers was evidenced. CER/POSS films exhibited a higher storage modulus than that of neat CER in the temperature range investigated. It was evidenced that CER/aminopropylisobutyl (APIB)-POSS, CER/N-phenylaminopropyl (NPAP)-POSS, and CER/aminoethyl aminopropylisobutyl (AEAPIB)-POSS nanocomposites induced a more homogenous α relaxation phenomenon with higher Tα values and an enhanced nanocomposite elastic behavior. Furthermore, CER/amino-POSS nanocomposites possessed higher specific surface area, gas permeability (CO2, He), and diffusion coefficients (CO2) values than those for neat CER, due to increasing free volume of the nanocomposites studied that is very important for their gas transport properties. Permeability grew respectively by about 2 (He) and 3.5-4 times (СО2), and diffusion coefficient of CO2 increased approximately twice for CER/amino-POSS nanocomposites in comparison with the neat CER network. The efficiency of amino-functionalized POSS in improving the thermal and transport properties of the CER/amino-POSS nanocomposites increased in a raw of reactive POSS containing one primary (APIB-POSS) &lt; eight secondary (NPAP-POSS) &lt; one secondary and one primary (AEAPIB-POSS) amino groups. APIB-POSS had the least strongly pronounced effect, since it could form covalent bonds with the CER network only by reaction of one –NH2 group, while AEAPIB-POSS displayed the most highly marked effect, since it could easily be incorporated into the CER network via reaction of –NH2 and –NH– groups with –O–C≡N groups from CER.

Activated carbons can be produced from biomass in a thermal process either in a direct carbonization-activation process or by first carbonizing the biomass and later on activating the biochars into activated carbons. The properties of the ACs are dependent on the type of process used for production. In this study, the properties of activated carbons produced in a one-stage and a two-stage process are considered. Activated carbons were produced by physical activation of two types of starting materials, bio chars produced from spruce and birch chips in a commercial carbonization plant and from the corresponding raw chips. The activated carbons produced were characterized regarding specific surfaces, pore volumes and pore size distributions. The un-activated bio chars had some degree of surface area 190 and 140 m²g^-1 for spruce and birch and pore volumes of 0.067 and 0.092 cm³g^-1. According to the results obtained, two slightly different types of activated carbons are produced depending if a one-stage or a two-stage carbonization and activation process is used. The ACs produced in the one-stage process had higher specific surface areas compared to the ones produced in a two-stage process (761-940 m²g^-1 vs. 540-650 m²g^-1) . In addition, total pore volumes were higher in one-stage process but development of micropores is greater compared to two-stage process. There was no significant difference in total carbon content between one-stage and two-stage process.

: Despite the elevated heat flow known in the Western part of the South Slave Region (Northwest Territories, Canada), a continuous and equilibrium geothermal gradient was never measured in boreholes below the communities where geothermal energy could be developed. This paper aims to predict the geothermal gradient and assess the Earth’s natural heat flow below the communities of Fort Providence, Kakisa, Hay River, and Enterprise. Temperatures from drill-stem test and bottom well logs were corrected for drilling disturbance and paleoclimates. Thermal conductivity and heat generation rate of the geological formations were determined from the literature and with new laboratory measurements. 1D models were developed to evaluate subsurface temperature through the sedimentary formations, based on a thermostratigraphic assessment. Results indicate a geothermal gradient varying from 44.1 ± 10.6 °C km-1 to 59.1 ± 14.9 °C km-1 and heat flow varying from 105.5 mW m-2 to 160.2 mW m-2 below the communities. These estimates are in agreement with the equilibrium geothermal gradients measured in the Cameron Hills, south of the four communities, and used to verify our predictions. Hay River appears to be the most promising community with the highest geothermal gradient estimated to be 59.1 ± 14.9 °C km-1.

Calcium dihydrogen phosphate monohydrate [Ca(H2PO4)2·H2O] (a fertilizer) was successfully synthesized by the recrystallization process by using a prepared triple superphosphate (TSP) that derived from oyster shell waste as starting material. This bio-green, eco-friendly process to produce an important fertilizer can promote a sustainable society. The shell-waste-derived TSP was dissolved in distilled water and kept at 30, 50, and 80 °C. Non-soluble powder and TSP solution were obtained. The TSP solution fraction were then dried and the recrystallized products (RCP30, RCP50, and RCP80) were obtained and confirmed as Ca(H2PO4)2·H2O. Whereas the non-soluble products (NSP30, NSP50, and NSP80) were observed as calcium hydrogen phosphate dihydrate (CaHPO4·2H2O). The recrystallized yields of RCP30, RCP50, and RCP80 were found to be 51.0%, 49.6%, and 46.3%, whereas the soluble percentages were 98.72%, 99.16%, and 96.63%, respectively. RCP30 shows different morphological plate sizes, while RCP50 and RCP80 present the coagulate crystal plates. X-ray diffractograms confirm the formation of both the NSP and RCP. The infrared adsorption spectra confirmed the vibrational characteristics of HPO42‒, H2PO4‒ and H2O existed in CaHPO4·2H2O and Ca(H2PO4)2·H2O. Three thermal dehydration steps of Ca(H2PO4)2·H2O (physisorbed water, polycondensation, and re-polycondensation) were observed. Ca(H2PO4)2 and CaH2P2O7 are the thermodecomposed products from the first and second steps, whereas the final product is CaP2O6.

Since people spend most of their time in indoor environments, the objective of this work was to study indoor air quality perception and its effects on users’ thermal comfort. Based on previous data from a building with a central air-conditioning system and two mixed-mode buildings located in the humid subtropical climate of Florianópolis, southern Brazil, statistical analyses were performed. Each user subjective answer obtained through a questionnaire was combined with the corresponding environmental conditions – measured using microclimate stations, a portable thermo-anemometer and a CO2 analyser. Results showed that improvement in air quality was associated with the reduction of air temperature and humidity ratio. Also, there was a significant influence of thermal, air movement and humidity sensation and acceptability of air quality perception. Users felt more satisfied or neutral with air quality for being in thermal comfort, and not because of the CO2 level – which means that air quality perception is influenced by factors other than CO2. This study recommends the implementation of an air exchange device in split air-conditioners with air recirculation used in mixed-mode buildings in Brazil. It is important to provide suitable indoor ventilation to reduce pollutants concentration, ensure good air quality and prevent respiratory diseases.

Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

Dye sensitized solar cell technology is having an important role in renewable energy research due to its features and low cost manufacturing processes. Devices based on this technology appear very well suited for integration into glazing systems due to their characteristics of transparency, color tuning and manufacturing directly on glass substrates. Field data of thermal and electrical characteristics of dye sensitized solar modules (DSM) are important since they can be used as input of building simulation models for the evaluation of their energy saving potential when integrated into buildings. However still few works in the literature provide this information. The study here presented wants to contribute to fill this gap providing a thermal and electrical characterization of a DSM in real operating conditions using a method developed in house. This method uses experimental data coming from test boxes exposed outdoor and dynamic simulation to provide thermal transmittance and solar heat gain coefficient (SHGC) of a DSM prototype. The device exhibits an U-value of 3.6 W/m²K, confirmed by an additional measurement carried on in the lab using a heat flux meter, and a SHGC of 0.2, value compliant with literature results. Electrical characterization evidences an increase of module power with respect to temperature causing DSM suitable for integration in building facades.

We discuss the consequences of the unique symmetry of the de Sitter spacetime. This symmetry leads to the specific thermodynamic properties of the de Sitter vacuum, which produces the thermal bath for matter. The de Sitter spacetime is invariant under the modified translations, ${\bf r}\rightarrow {\bf r} -e^{Ht}{\bf a}$, where $H$ is the Hubble parameter. For $H\rightarrow 0$, this symmetry corresponds to the conventional invariance of Minkowski spacetime under translations ${\bf r}\rightarrow {\bf r} -{\bf a}$. Due to this symmetry, all the comoving observers at any point of the de Sitter space perceive the de Sitter environment as the thermal bath with temperature $T=H/\pi$, which is twice larger than the Gibbons-Hawking temperature of the cosmological horizon. This temperature does not violate the de Sitter symmetry, and thus does not require the preferred reference frame, as distinct from thermal state of matter, which violates the de Sitter symmetry. This leads to the heat exchange between gravity and matter, and to instability of de Sitter state towards the creation of matter, its further heating, and finally to the decay of the de Sitter state. The temperature $T=H/\pi$ determines different processes in the de Sitter environment, which are not possible in the Minkowski vacuum, such as the process of ionization of an atom in the de Sitter environment. This temperature also determines the local entropy of the de Sitter vacuum state, and this allows us to calculate the total entropy inside the cosmological horizon. The result reproduces the Gibbons-Hawking area law, which is related to the cosmological horizon, $S_{\rm hor}=4\pi KA$, where $K=1/16\pi G$. This supports the holographic properties of the cosmological event horizon. We extend the consideration of the local thermodynamics of the de Sitter state using the $f({\cal R})$ gravity. In this thermodynamics, the Ricci scalar curvature ${\cal R}$ and the effective gravitational coupling, $K$, are thermodynamically conjugate variables. The holographic connection between the bulk entropy of the Hubble volume, and the surface entropy of the cosmological horizon remains the same, but with the gravitational coupling $K=df/d{\cal R}$. Such connection takes place only in the $3+1$ spacetime, where there is the special symmetry due to which the variables $K$ and ${\cal R}$ have the same dimensionality. We also consider the lessons from the de Sitter symmetry for the thermodynamics of black and white holes.

The drug delivery systems receive more and more attention for the control and treatment of many diseases due to their increased number in recent years. The main aims of this study were to develop and to characterize a polyurethane drug delivery system that it is intended to be used for the transmembrane transport of nucleosides. Three different samples have been synthesized based on aliphatic diisocyanates (hexamethylene diisocyanate, isophorone diisocyanate and lysine diisocyanate) as organic phase, respectively a mixture of polyethylene glycol, polycaprolactone diol and low molecular weight diols as aqueous phase. The samples were characterized by pH, refractivity index and solubility measurements, drug loading efficacy and release investigations, thermal behavior, Zetasizer, cells viability and irritation tests on mice skin. The results indicate the obtaining of different populations of neutral acido-basic particles with size between 132 and 190 nm; the Zeta potential values and SEM images show a medium tendency to form clusters, while UV-Vis evaluations indicate an almost 70% encapsulation efficacy, a prolonged release (45% of encapsulated substance is released in the first 5 days) and around 70% of particles have penetrated an artificial membrane in the first 24h. The synthesized products can be tested in further clinical trials, the currently tests on cells culture and mice skin revealing no side effects.

Deforestation is an important environmental problem in México and a key promoter of regional climate change through modifying the surface albedo. The objective of this research was to characterize the impact of deforestation and land use changes on surface albedo (α) and climate patterns in the Municipality of Tapalpa, Jalisco, México between the years 2014 and 2021. The main land cover types are coniferous forests (CF), oak and gallery woodlands (OGW), and annual agriculture (AA); which represent more than 88% of the regional territory (1066.03 km2). We used 2014 and 2021 Landsat 8 OLI images with topographic and atmospheric correction, in order to develop an inventory of albedo values for each land cover type in both time scenarios. Albedo images were generated by using the equation proposed by Liang in 2001, which is based on the reflectance of the bands 2, 3, 4, 5, and 7. Differences in albedo values were calculated between the years 2014 and 2021, and those differences were correlated with variations in climate parameters, for which we used climate data derived from the WRF model. In addition, the different land use changes found were classified in terms of triggers for increasing or decreasing surface albedo. Results showed that between 2014 and 2021, at least 38 events of land use change or deforestation occurred, with albedo increments between 1 and 11%, which triggered an average increment of 0.57% of the regional surface albedo in comparison to 2014 scenario. From 2014 to 2021, the albedo for CF, OGW, and AA, increased significantly (p&lt;0.001; Mann-Whitney U Test) by 79, 12, and 9%, respectively. In addition, the regional albedo increment was found to be significant and negatively correlated (p&lt;0.01 Spearman’s coefficient) with relative humidity (RH), maximum temperature (Tmax), minimum temperature (Tmin), and diurnal thermal range (DTR). The decrease in the regional values of relative humidity in 2021, occurred even when in that year the annual precipitation levels were higher than those of 2014, hence, reinforcing the fact of a possible climatic effect of the regional albedo changes. Conversion of CF and OGW into AA, perennial agriculture (PA), or grassland (GR) always yielded an albedo increment, whilst the conversion of AA to irrigation agriculture or PA triggered a decrease in albedo, and finally, the pass from GR or AA to protected agriculture caused albedo increase or decrease, depending on the greenhouse covers materials. Reducing deforestation of CF and OGW, conversion of AA or GR into PA, and selecting adequate greenhouse covers could help to mitigate regional climate change.

In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

A novel hybrid cobalt phosphite, (H2DAB)[Co(H2PO3)4]·2H2O, has been synthesized by using slow evaporation method, in the presence of cobalt nitrate, phosphorous acid and 1,4- dia-minobutane (DAB= 1,4- diaminobutane) as a structure-directing agent. Single crystal X-ray diffraction analysis showed that the compound crystallizes in the P-1(n.2) triclinic space group, with the following unit cell parameters (Å, °) a = 5.4814 (3), b = 7.5515 (4), c = 10.8548 (6), α = 88.001 (4), β = 88.707 (5), γ = 85.126 (5), and V= 447.33 (4) Å3. The crystal structure was built up from cor-ner-sharing [CoO6] octahedra, forming chains parallel to [001], which are interconnected by H2PO3 pseudo-tetrahedral units. The deprotonated cations, residing between the parallel chains, interacted with the inorganic moiety via hydrogen bonds leading thus to the formation of the 3D crystal structure. The Fourier transform infrared spectrum showed characteristic bands corresponding to the phosphite group and the organic amine. The thermal behavior of the compound consisted mainly of the loss of its organic moiety and the water molecules. The biological tests exhibited significant activity against Candida albicans and Escherichia coli strains in all used concentrations, while less inhibitory activity was pronounced against Staphylococcus epidermidis and Saccharomyces cerevisiae, and in the case of multi-cellular organisms, no activity against the nematode model Steinernema feltiae was detected.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

The paper deals with an electrothermal model of a thermoelectric converter dedicated to performing simulations of coupled thermal and electrical phenomena taking place in harvesting processes. The proposed model is used to estimate the electrical energy gain from waste heat that would be sufficient to supply electronic circuits, in particular autonomous battery-less nodes of wireless sensor networks (WSN) and Internet of Things (IoT) devices. The developed model is not limited to low power electronic solutions such as WSN or IoT; it can also be scaled up and applied to simulations of considerably higher thermal power conversion. In the paper, a few practical case studies are presented that show the feasibility and suitability of the proposed model for complex simultaneous simulation processes, in both electrical and thermal domains. The first example deals with a combined simulation of the electrothermal model of a thermoelectric generator (TEG) and an electronic harvester circuit based on Analog Devices’ power management integrated circuit LTC3108. The second example relates to the thermalization effect in heat sink-less harvesting applications that could be mitigated by a pulse mode operation.

Metals are indispensable in the life of all organisms, in fact, their dysregulation causes various disorders caused by an interruption of their homeostasis. Nowadays different transition metals are incorporated into pharmaceutical products as diagnostic and therapeutic agents because of their electronic structure which gives them versatility in terms of tuning molecule properties, differently from organic molecules. Hence the interest in the study of metal-drug complexes from different points of view was born and many approaches were developed for the characterization, activation, delivery and molecular mechanisms clarification. The integration of these different approaches starting from chemoproteomics passing through nanoparticle systems to different activation strategies allows the understanding of the cellular responses of metallic drugs, which can be the basis for the design of new drugs and/or modification of drugs currently in use. This review aims to briefly summarize the recent advances in this area by describing the technological platforms and their possible applications to identify protein targets for discovering the mechanisms of action of metallodrugs, and to improve their efficiency in terms of administration.

The pressing threat of global warming poses significant risks to plant survival, adversely affecting their growth and agricultural productivity. It is crucial to understand how plants react to heat stress at the molecular level to develop crops that can withstand higher temperatures. In our study, we investigated the proteome dynamics of *Arabidopsis thaliana* seedlings under moderate heat stress conditions (30°C) using a combination of 15N-stable isotope labeling and the ProteinTurnover algorithm. This approach allowed us to closely examine the proteomic changes across different cellular compartments. Our findings revealed significant changes in the turnover rates of 571 proteins, with an average increase of 1.4-fold, indicating enhanced protein dynamics under heat stress. Notably, root soluble proteins showed more subtle changes, suggesting tissue-specific responses. We also detected significant turnover variations in proteins involved in redox signaling, stress response, and metabolism, highlighting the complex nature of these adaptive mechanisms. In contrast, proteins related to carbohydrate metabolism and mitochondrial ATP synthesis showed little change, underscoring their stability. This detailed analysis illuminates the proteomic adaptations of *Arabidopsis* seedlings to moderate heat stress, enhancing our understanding of plant thermal resilience and supporting efforts to develop thermotolerant crops.

A focal plane array (FPA) detector was used for hyperspectral imaging in the infrared (IR) spectral region using thermal and synchrotron light sources. FPA Fourier-transform IR (FTIR) imaging microspectroscopy will be able to monitor real time changes at specific absorption bands when combined with high brightness synchrotron source. In this study, several types of samples with unique structural motifs were selected and used for assessing the capability of the FPA-FTIR imaging technique. It was shown that the time required for polariscopy at IR wavelengths can be substantially reduced by the FPA-FTIR imaging approach. By using natural and laser fabricated polymers with sub-wavelength features, alignment of absorbing molecular dipoles was revealed as well as higher order patterns (laser fabricated structures). Micro-spectroscopy of absorber orientation reveals alignment patterns even when they are not spatially resolved.

High-methoxyl apple pectin (AP) derived from apple was employed as the main ingredient facilitating rheological modification features for developing dysphagia-friendly fluidized alimentary matrices. Xanthan gum (XG) was also included as a composite counterpart to modify the viscoelastic properties of the thickened system under different thermal processes. The results indicate that AP is extremely sensitive to thermal processing, and the viscosity is greatly depleted under a neutral pH level. Moreover, the inclusion of calcium ions echoed a modification effect on the rheological properties of AP, and both the elastic property and viscosity value are promoted after thermal processing. The modification effect of viscoelastic properties (Gʹ and Gʹʹ) is observed while XG is incorporated into the composite formula. By promoting the XG ratio from 7: 3 to 6: 4 (AP: XG), it triggers the rheological transformation from a liquid-like form to a solid-like state, and the viscosity value shows that the AP-XG composite system exhibits better thermal stability after thermal processing. The ambient modifiers of pH (pH &lt; 4) and calcium chloride concentration (7.5%) with an optimal AP-XG ratio of 7:3 lead to weak-gel-like behavior (Gʹʹ &lt; Gʹ), helping to maintain the texture properties of dysphagia-friendly features similar to those prior to the thermal processing.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

Thermodynamic cycles are not only the core concepts of thermal science, but also key approaches to energy conversion and utilization. So far, power cycles and refrigeration cycles have been the only two general classes of thermodynamic cycles. While diverse types of systems have been developed to perform thermodynamic cycles, no new general classes of thermodynamic cycles have been proposed. Based on the basic principles of thermodynamics, here we propose and analyze a new general class of thermodynamic cycles named class 1 heating cycles (HC-1s). Two basic forms of HC-1s are obtained by connecting six essential thermodynamic processes in the proper order and forming a thermodynamic cycle. HC-1s present the simplest and most general approach to utilizing the temperature difference between a high-temperature heat source and a medium-temperature heat sink to achieve efficient medium-temperature heating and/or low-temperature cooling. HC-1s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in energy conservation and emission reduction.

Is it possible to quantify in General Relativity, GR, the entropy generated by supermassive black holes, BHs, during its evaporation time, since the intrinsic Hawking radiation in the infinity that, although insignificant, is important in the effects on the thermal quantum atmosphere?The purpose was to develop a formula that allows us to measure the entropy generated during the evaporation time of different types of BHs of: i. remnant BH of the binary black holes’ merger, BBH: GW150914, GW151226 and LTV151012 detected by the Laser Interferometer Gravitational-Wave Observatory (LIGO), and ii. Schwarzschild, Reissner-Nordström, Kerr and Kerr-Newman, and thus quantify in GR the “insignificant” quantum effects involved, in order to contribute to the validity of the generalized second law (GSL) that directly links the laws of black hole mechanics to the ordinary laws of thermodynamics, as a starting point for unifying quantum effects with GR. This formula could have some relationship with the detection of the shadow’s image of the event horizon of a BH.This formula was developed in dimensional analysis, using the constants of nature and the possible evaporation time of a black hole, to quantify the entropy generated during that time. The energy-stress tensor was calculated with the 4 metrics to obtain the material content and apply the proposed formula.The entropy of the evaporation time of BHs proved to be insignificant, its temperature is barely above absolute zero, however, the calculation of this type of entropy allows us to argue about the importance of the quantum effects of Hawking radiation mentioned by authors who have studied the quantum effects with arguments that are fundamentally based on the presence of the surrounding thermal atmosphere of the black hole.

Abstract Due to the relatively low efficiency of thermoelectric (TE) generators, they have mostly been used in niche applications where the unique properties of TE generators outweigh their lack of efficiency, or conditions where it is more reasonable to base the optimal design on maximum generated power rather than maximum efficiency. The aim of this work is to investigate how the different fundamental transport properties (Seebeck coefficient, thermal conductivity and electrical resistivity) in materials with equal figure of merit (ZT) impact TE module design and maximum power output. Further, we discuss and review the strategies to enhance material properties and the latest studies on the TE module performance. It is shown, that by increasing the power factor by a factor of 15 and decreasing the thermal conductivity by 13.33 in order to maintain ZT=1, power output is increased by 45%. This effect is stronger in lower module fill factor and thermal resistance of the heat source and heat sink.

This paper evaluates norms and assesses the level of knowledge in air conditioning project management within the construction industry. A total of 25 questions were distributed to multiple candidates, who were filtered based on pre-established inclusion and exclusion criteria. Thirty-nine candidates were ultimately approved to participate in the survey. The questions were designed to address five hypotheses, with each set of five questions corresponding to one hypothesis. The results were obtained after pre-processing the data using Matlab software. The data was pre-processed using Matlab software, and the results were analyzed using the Delphi method. The analysis revealed that only two hypotheses were approved: No matter whether there are nationalized safety rules or not, the impact of data sciences and smart technologies, including air conditioning management systems, is critical for human life in the building business.

Using number theory, a formula is obtained that describes the thermal conductivities of ZrC, UC, UN, ThN, ZrN and Th_xU_1-xN at x = 0.2 and 0.5 with temperature change. This formula contains the atomic numbers of the elements, the thermal conductivities of the individual elements of the substance, and the structural parameter. There is no direct dependence on temperature in the formula, since it is hidden in the thermal conductivities of each element and in the structure parameter. In some temperature ranges, the structural parameter is constant; therefore, the thermal conductivity of some carbides and nitrides is expressed through summing the thermal conductivities of individual elements.

Long-term durability of the vacuum edge-seal plays a significant part in retrofitting triple vacuum glazing (TVG) to existing buildings in achieving towards zero-energy buildings (ZEB) target. Vacuum pressure decrement with respect to time between panes affect the thermal efficiency of TVG. This study reports a 3D finite element model, with validated mathematical methods and comparison, for the assessment of the influence of vacuum pressure diminution on the thermal transmittance (U value) of TVG. The centre-of-pane and total U values of TVG calculated to be 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ at the cavity vacuum pressure of 0.001 Pa. The results suggests that a rise in cavity pressure from 0.001 Pa to 100 kPa increases the centre-of-pane and total U values from 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ to 2.4 Wm⁻²K⁻¹ and 2.58 Wm⁻²K⁻¹, respectively. The temperature descent on the surfaces of TVG between hot and cold sides’ increases by decreasing the cavity vacuum pressure from 50 kPa to 0.001 Pa. To maintain the cavity vacuum pressure of 0.001 Pa for over 20 years of life span in the cavity of 10 mm wide edge sealed triple vacuum glazing, non-evaporable getters will maintain the cavity vacuum pressure that will enable the long-term durability to TVG.

This work aims to investigate the effect of process temperature and catalyst content by pyrolysis and thermal catalytic cracking of (organic matter + paper) fraction from municipal household solid waste (MHSW) on the yields of reaction products (bio-oil, bio-char, H2O, and gas), acid value and chemical composition of bio-oils, and characterization of bio-chars, in laboratory scale. The collecting sectors of MHSW in the municipality of Belém-Pará-Brazil were chosen based on geographic and socio-economic database. The MHSW collected and transported to the segregation area. The gravimetric analysis of MHSW carried out and the fractions (Paper, Cardboard, Tetra Pack, Hard Plastic, Soft Plastic, Metal, Glass, Organic Matter, and Inert) separated. The selected organic matter and paper submitted to pre-treatment of crushing, drying, and sieving. The experiments carried out at 400, 450, and 475 °C and 1.0 atmosphere, and at 475 °C and 1.0 atmosphere, using 5.0, 10.0, and 15.0% (wt.) Ca(OH)2, in batch mode. The bio-oil characterized for acid value. The chemical functions present in bio-oil identified by FT-IR and the composition by GC-MS. The bio-char characterized by SEM, FT-IR and XRD. The variance in mass (wt.%) for organic fraction of municipal household solid waste, between 56.21 and 67.45% (wt.), lies with the interval of 56% (wt.) and 64% (wt.) of OFMHSW for middle and low income countries. The pyrolysis of MHSW fraction (organic matter + paper) show bio-oil yields between 2.63 and 9.41% (wt.), aqueous phase yields between 28.58 and 35.08% (wt.), solid phase yields between 35.29 and 45.75% (wt.), and gas yields between 16.54 and 26.72% (wt.). The bio-oil yield increases with pyrolysis temperature. For the catalytic cracking, the bio-oil and gas yields increase slightly with CaO content, while that of bio-char decreases, and the H2O phase remains constant. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, alkynes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, phenols, and aldehydes), as well as compounds containing nitrogen, including amides and amines. The acidity of bio-oil decreases with increasing process temperature and with aid Ca(OH)2 as catalyst. The concentration of hydrocarbons in bio-oil increases with increasing Ca(OH)2-to-MHSW fraction ratio due to the catalytic deoxygenation of fatty acids molecules, by means of de-carboxylation/de-carbonylation, producing aliphatic and aromatic hydrocarbons.

The thermal conductivity of the products of the interaction of molten core with concrete was derived using number theory. A formula has been found that describes the thermal conductivity of ZrO₂, ZrSiO₄, (U,Zr)SiO₄ and UO₂ over a wide temperature range. Formula is expressed in terms of the atomic numbers of elements, their valencies, the crystal structure of substances, and the thermal conductivities of individual chemical elements of the corium.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Space vehicles may be propelled by solar sails exploiting the radiation pressure coming from the sun and applied on their surfaces. This work deals with the adoption of Shape-Memory Alloy (SMA) elements in the sail deployment mechanism activated by the Joule Effect, i.e. using the same SMA elements as a resistance within suitable designed electrical circuits. Mathematical models were analyzed for the thermal analysis by implementing algorithms for the evaluation of the temperature trend depending on the design parameters. Several solar sail prototypes were built up and tested with different number, size and arrangement of the SMA elements, as well as the type of the selected electrical circuit. The main parameters have been discussed in the tested configurations and advantages discussed as well.

The preparation of transition metal salt ammine complexes having oxidizing anions is a great challenge due to the reaction between the ammonia and oxidizing anions during the synthesis of these materials. However, they have an important role in the development of new oxidants in organic chemistry and especially as precursors in the preparation of mixed metal oxides and alloys in controlled temperature thermal decomposition reactions. Therefore, the synthetic procedures to prepare the complexes of transition metal permanganate, pertechnetate, and perrhenate (VIIB group tetraoxometallates) salts with ammonia as ligand or co-ligand have been comprehensively reviewed. The available data about the structure and spectroscopic properties of these compounds, including the hydrogen bonds that act as redox reaction centers under their thermal decomposition are given and evaluated. Their thermal decomposition processes and products have been summarized. The available pieces of information about their role in organic oxidation reactions like the oxidation of benzyl alcohols, and regeneration of oxo-compounds from oximes and phenylhydrazones including the kinetics of these processes have also been collected.

The thermal decomposition of siderite and its decomposition products in a vacuum atmosphere was investigated for the first time using in situ high-temperature transmission Mössbauer spectroscopy. These measurements were supported by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, and magnetic measurements. In situ Mössbauer spectra were collected from room temperature (RT) to 750 oC with a temperature step of 50 oC. After that, the sample was cooled down to RT with step 100 oC. Raw siderite samples contain siderite as the only iron-bearing mineral, and after heating the samples at high temperatures, hematite and magnetite are only Fe-bearing phases. In the temperature range of 300 oC - 500 oC, siderite decomposition occurs. The analysis shows that siderite transforms directly into magnetite, and then hematite generation occurs as long as siderite is present in the sample. Changing hyperfine parameters like isomer shift, quadrupole splitting, or hyperfine magnetic field versus temperature were obtained for siderite and iron oxides (hematite, magnetite). The measurements also show that magnetite formed during the decomposition of siderite is a composition of particles of various sizes and a low degree of crystallization.

In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

The central coast is one of the importantly livable regions in China, and green land plays a meaningful role in improving human settlements through regulating ecosystem services. However, the research on spatiotemporal heterogeneity of green land in different urbanized areas are still lacking in this region, which limits the timeliness of reporting on the land-surface thermal properties of residential environment from green land perspective. To address this issue, the synergistic methodology of “artificial numerical technology -- urban interior mixed pixel classification -- surface radiation energy balance model” was applied to investigate the green land change and its impact on human settlements in Rizhao region, which is known for its coastal ecology and greenery in China and obtained the United Nations habitat award. Main conclusions of this study are below: (1) Although total green land decreased by 474.05 km2, resulting in a decrease of 9.17% in its share of the entire study area from 2000-2022 during the urbanization process, but the greening levels improved within the built-up area, with the greening proportion of 25.34% in 2000 and 42.98 km2 in 2022. (2) Differences in green land at different urbanized regions were first observed, namely, urban greening rate was 37.78% in the old urban areas of 2022, while it was up to 46.43% in new urban areas. More attention was paid to the construction of urban green space during urban expansion, which will inevitably bring better visual and comfort experience to residents. (3) Thermal comfort indicators for urban residents were evaluated in latent heat flux (0-457.83 W/m2), sensible heat flux (0-645.09 W/m2), total available energy (254.07-659.42 W/m2) and others. (4) The lowered cooling temperature effect in the middle, high green land density region was 1.05 ℃ and 2.12 ℃ compared to the low-density region, and the average air temperature was 25.86 ℃. Also, spatial patterns of hot and cold uncomfortable areas were displayed in this study. Overall, this study provides the meaningfully practical reference for exploring the spatiotemporal heterogeneity of green land and its impact on residents' environments from the perspective of land-surface thermal properties in coastal areas of China and around the world.

Fractured media are seldom considered viable for storing excess thermal energy seasonally, compared to the more commonly used porous aquifers, due to their heterogeneity, lower storage capacity, and potential for unpredictable flow paths. This study employs COMSOL Multiphysics to create a numerical model of a fractured granite reservoir located below the Bedretto underground laboratory. The energy efficiency of both single-well and doublet systems was evaluated over 25 cycles, each comprising four 91-day phases: injection, storage, production, and resting. Results indicated that the single-well system was more efficient, with energy efficiency increasing with the flow rate. For an injection temperature of 60 °C, the system achieved energy efficiencies of up to 59.3% and 67.7%, after 10 and 25 cycles, respectively, aligning with porous Aquifer Thermal Energy Storage (ATES) system efficiencies at this temperature. Exploration of electricity production using water injected at 120 °C revealed it to be uneconomical and ineffective. However, the most promising use of the retrieved water was found to be direct ground heating for a greenhouse. This technology offers a potential alternative for thermal energy storage in regions lacking suitable porous aquifers, although identifying appropriate locations with the necessary geological characteristics may present significant challenges.

In this study, seven mortar mixes were prepared by replacing natural sand by crumb rubber ,CR, (10%, 25%, 50%, 60%, 75% and 100%). The properties of mortars, both in their fresh and hardened states, were studied. Key characterisitcs, including density, water absorption coefficient, porosity, thermal conductivity, heat capacity, shrinkage/swelling, elastic modulus, compressive strength, flexure strength, fracture energy and performance after exposure to heat, were evaluated. The results obtained showed that as the CR fraction increased, density, initial setting time, and workability decreased but mortars with CR fractions ranged between 25% and 50% are lightweight and can be used for repairing as they fulfill satndards. It was observed that strengths and stiffness decreased with higher CR content while shrinkage increased for CR percentage higher than 60%. However, up to 50% of CR content the mortars obey to the standards for repair. Interestingly, incorporating up to 50% waste tires proved to improve comfort and thermal resistance without affecting thermal inertia. A slight increase in the mass loss is observed when mortars are exposed to high temperatures. Mortars containing CR between 25% and 50% can be classified as lightweight and thermally insulating mortars, suitable for repairing concrete structures in accordance with industry standards.

High-performance insulation and airtight building envelopes are the two most important factors to optimize the building energy efficiency and thermal performance. However, thermal performance of building envelopes can be significantly affected by thermal bridging. Thermal bridges can take place at different locations of the building envelope, causing added transmission losses, increasing heat flow, lower inner surface temperatures. Thermal bridges are regarded in all national regulations for new buildings of all states of European Union (EU) but there are no specifications assessing balconies to wall junctions and the impact on the building thermal performance is not well regulated. In this paper, balcony to wall thermal bridge assessment using infrared thermography is highlighted. The originality is that, infrared thermography, has been applied to a real living latest building in the north east of France showing that there is noncompliance in the national regulations as some exigencies are not met. Thermography of thermal break windows and window doors has also revealed air leakage. The goal, is to illustrate that thermal imaging is a means of quality assurance to new building specifications and should include a clause specifying quality assurance procedure for balconies junction in national building regulations for all states if the EU.

Graphene is a two-dimensional nanostructured material with intrinsic properties that show promising performance in various applications, including electronics, renewable energy, medicine, mechanical enforcement and others. This study reports a bottom-up approach for the conversion of cyclohexane into graphene nanoflakes, which were then deposited onto fiberglass using a non-thermal generator. The composite was characterized using transmission electron microscopy, which revealed the formation of stacked few-layer graphene with a partially disordered structure and a d-spacing of 0.358 nm between the layers. X-ray diffraction confirmed the observations from the TEM images. SEM images showed the agglomeration of carbonaceous material onto the fiberglass, which experienced some delamination due to the synthesis method. Raman spectroscopy indicated that the obtained graphene exhibited a predominance of defects in its structure. Additionally, Atomic Force Microscopy (AFM) analyses revealed the formation of graphene layers with varying levels of porosity.

No system nor standardized analytical procedures at commercial laboratories exist to facilitate and accurately measure potential viable virus contamination in feed ingredients and complete feeds globally. As a result, there is high uncertainty of the extent of swine virus contamination in global feed supply chains. Many knowledge gaps need to be addressed to improve our ability to prevent virus contamination and transmission in swine feed. This review summarizes the current state of knowledge involving: 1) the need for biosecurity protocols to identify production, processing, storage, and transportation conditions that may cause virus contamination of feed ingredients and complete feed, 2) challenges of measuring virus inactivation, 3) virus survival in feed ingredients during transportation and storage, 4) minimum infectious doses, 5) differences between using a Food Safety Objective versus a Performance Objective as potential approaches for risk assessment in swine feed, 6) swine virus inactivation from thermal and irradiation processes, and chemical mitigants in feed ingredients and complete feed, 7) efficacy of virus decontamination strategies in feed mills, 9) benefits of functional ingredients, nutrients, and commercial feed additives in pig diets during a viral health challenge, and 10) considerations for improved risk assessment models of virus contamination in feed supply chains.

Biomass burning is an important and changing component of the global and hemispheric carbon cycles. In particular, boreal forest fires in Russia and Canada are important sources of greenhouse gases carbon dioxide (CO2) and methane (CH4). The influence of carbon monoxide (CO) on the climate is insignificant: its main absorption bands of 4.6 and 2.3 μm are far away from the climatically important regions of the spectrum. Meanwhile, CO concentrations in fire plumes are closely related to CO2 and CH4 emissions from fires. On the other hand, satellite measurements of CO are much simpler than those for the aforementioned gases. The Atmospheric Infrared Sounder (AIRS) provides a long satellite-based CO data set. This article presents estimates of CO emissions from biomass burning north of 30° N using a simple two-box model. These results correlate closely with independently estimated CO emissions from the GFED4 bottom-up data base. Both ones reported record high emissions in 2021 throughout two decades, double the annual emissions comparing to the previous a few years. There have been several years with extreme emissions, but for the rest of data upward trend with a rate of 3.7 ± 2.3 Tg CO yr-2 (4.4 ± 2.8% per year), was found.

Heating has been recently used as an alternative application to electrical stimulation to modulate excitability and to induce neuritogenesis and the expression of neuronal markers, but a long-term functional differentiation has not been described so far. Here we present the results obtained by a new approach for scalable thermal stimulation on the behavior of a model of dorsal root ganglion neurons, the F-11 cell line. Initially, we performed experiments of bulk stimulation in incubator for different time intervals and temperatures, and significant differences in neurite elongation and in electrophysiological properties were observed in cultures exposed at 41,5°C for 30 minutes. Thus, we exposed the cultures to the same temperature increase by irradiating, with a near infrared laser, a disc of Prussian Blue nanoparticles and poly-vinyl alcohol, that we stuck on the outer surface of the petri dish. In irradiated cells neurites were significantly longer and the electrophysiological properties (action potential firing frequency and spontaneous activity) were significantly increased compared to the control. These results suggest that a targeted thermal stimulation could be a promising technique to induce differentiation and support the future application of this method as a strategy to modify neuronal behavior in vivo.

In this research, Cellulose Nanofibers (NFC) modified with a eutectic of lauric acid (LA) was prepared as a new form-stable phase change material (NFC-LA). Thermal properties of this composite were investigated by Differential Scanning Calorimetry (DSC). The results revealed that the melting temperature and latent heat of NFC/LA were 21.56 °C and 88.5 J/g, respectively; and the super cooling degree for the NFC-LA composite decreased to 13.99 °C when compared to 20.28 °C of the pure lauric acid. Natural clay was purified and modified with Cetyltrimethyl ammonium bromide (CTAB) to prepare organoclay. Through FTIR spectra, we have confirmed that the clay was successfully modified. The PCM-composite was then added to the organoclay to obtain a new composite denoted NFC-LA-OC. this latter was added to cement and was investigated as a reinforcement material in cement mortars for thermal energy storage application. The prepared material can both solve the leakage problem associated to the phase change material, and reduce or even avoid the use of heating and air conditioning systems, which are energy-intensive systems, and therefore reduce energy consumption.

One-dimensional chain of core-shell pairs connected by ideal springs enables design of the metamaterial demonstrating the negative effective density and negative specific thermal capacity. We assume that the molar thermal capacity of the reported metamaterial is governed by the Dulong-Petit law in its high temperature limit. The specific thermal capacity depends of the density of the metamaterial; thus, it is expected to be negative, when the effective density of the chain is negative. The range of the frequencies enabling the effect of the negative thermal capacity is established. Dependence of the effective thermal capacity on the exciting frequency for various core/shell mass ratios is elucidated. The effective thermal capacity becomes negative in the vicinity of the local resonance frequency ω0 in the situation when the frequency ω approaches ω0 from above. The effect of the negative effective thermal capacity is expected in metals in the vicinity of the plasma frequency.

Droughts occurring more and more frequently in recent years are usually associated with progressive climate changes. Modern monitoring methods is mainly associated with agricultural use due to the high market demand for services protecting against agricultural losses. In natural wetland ecosystem this problem is neglected which is probably due to fact that this are ecosystems rich in water by definition. Nevertheless this droughts might become a problem of wetlands, whose good condition depends on adequate hydration. Therefore this study focused on determination Crop Water Stress Index (CWSI) for natural heterogeneous wetland habitats. CWSI based on remotely sensed land surface temperature and associated basic meteorological (air temperature and humidity) measurements. CWSI was calculated based on high resolution LST measurements from UAV platform and compare with on ground measurements of soil moisture, CCI, fAPAR and meteorological conditions. Results shows that CWSI properly shows water condition of plants in measured habitats and revels high importance of metrological conditions during data acquisition.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.