Pressmud, a by-product of sugarcane processing, is typically disposed of through incineration or landfilling, though it has considerable potential in organic agriculture. This study explored the com-posting of pressmud through bioaugmentation using specific bacterial strains. Two experimental setups were created: E2 with a cellulolytic and phosphorus-solubilizing strain, Bacillus amyloliquefa-ciens-ASK11, and E3 with a nitrogen-fixing strain, Bacillus megaterium-ASNF3. A control setup (E5) was also maintained without bacterial augmentation. Nitrogen (N) and phosphorus (P) contents were measured using the Kjeldahl and Olsen methods, respectively, while Fourier-Transform Infra-red (FTIR) spectroscopy confirmed compost maturity. Results indicated that the Bacillus-enhanced composts in E2 and E3 significantly increased the nitrogen(49.27% and 91.23%) and phosphorus contents(129% and 83.85%), respectively, compared to the control with only 13.62% N and 65% P contents after 60 days of the pressmud compost maturity.. Additionally, organic matter decomposi-tion improved by 49-50% in the bioaugmented setups after 60 days. FTIR analysis revealed organic phosphate peaks and P-O-C stretching bands at 1025 cm-1 in the E2 compost, while a nitrogen vi-bration band at 3849 cm-1 in E3 indicated significantly higher nitrogen content compared to the control. The Bacillus-enriched pressmud compost not only accelerated the composting process but also enhanced nutrient levels, positioning it as a promising biofertilizer for rehabilitating barren lands.

Glucagon-like peptide-1 (GLP-1) agonists are gaining attention as a potential treatment for obesity. While studies have shown that these medications greatly impact dietary habits, their relationship to consumer food waste is unexplored. We analyzed data from 505 U.S. consumers who self-report GLP-1 medication use and found that 25% agree that they waste more food since beginning the medication with 61% disagreeing with this statement. Respondents are less likely to agree with this statement if they have been on the medication a longer time and more likely to agree if they report experiencing nausea since beginning the medication. Several dietary changes are also significantly associated with self-reported changes in food waste since starting the medication. With previous literature finding GLP-1’s significant impact on individual food consumption and dietary choices, our findings suggest that the effects of this novel class of anti-obesity medications may cast a significant impact on food waste patterns. With the potential for widespread adoption of these medications, and given that approximately one-third of food in the United States is wasted by consumers, understanding the interaction of these two consumer trends is critical for projecting their joint impact on the food system.

High production and consumption of bananas produce large amounts of banana waste. However, the perception of banana as waste depends on the degree of ripeness, and is therefore subjective, depending on the sensorial perception, emotional reactions, and cultural differences of consumers. Understanding consumer perception of different levels of banana ripeness could contribute to better management of the supply chain, leading thus to a decrease of waste or better utilization of its waste as a byproduct. The aim of this study was to compare European and Chinese consumers’ sensorial and emotional responses to different stages of banana ripeness, using facial expression analysis, liking, and emotion measurement by self-report. One hundred and thirty-five adults of European and Chinese origin watched a video of banana consumption at five different degrees of ripeness. Participants’ facial expressions were analyzed with regard to six emotions (neutral, happy, sad, surprised, angry, disgusted, scared). Emotional responses and consumer acceptance of different degrees of banana ripeness were assessed using pictures of bananas as reference. Liking on a 9-point Likert scale and emotion measurement using PrEmo® followed, to evaluate emotional responses and acceptability of different degrees of banana ripeness. Results showed significant differences in facial reactions between cultures and among ripeness degrees. The European participants were more positively inclined towards all ripeness degrees, compared to the Chinese. Cultural expectations and level of familiarity seem to affect consumer acceptability greatly. Finally, explicit methods can give a more accurate picture of consumer preference and acceptance of different banana ripeness stages. A combination of liking and emotion measurement can be very effective in understanding consumer preference.

The presented work offers a novel process scheme for valorizing historical Pb-Zn slag, which involves crushing, grinding, and then using separation techniques to concentrate valuable components (nonferrous metals). This methodology could have a significant impact on the global beneficiation of metallurgical slags since, in theory, it is significantly more simple, environmentally friendly, and cost-effective than standard pyrometallurgical or hydrometallurgical procedures. According to previous physicochemical and mineralogical studies, Pb-Zn slag from "Topilnica" Veles is a valuable secondary raw material. This inhomogeneous technogenic resource contains substantial amounts of nonferrous metals (Pb, Zn, Cu, and Ag). However, laboratory tests have indicated that the Pb-Zn slag contains a very uneven valuable metals amounts, ranging from several g/ton to several tens of g/ton. The main issue is that traditional metallurgical procedures for releasing beneficial elements are not commercially viable since the valuable elements are "trapped" within amorphous aluminosilicates or intergrowths of alloy grains and glassy phases. Gravity concentration (Wilfley 13 shaking table) and magnetic separation (Davis separator and disk separator) were used to obtain the final concentrate following comminution and grindability testing. The gravity concentration proved more effective. This streamlined approach of valorizing Pb-Zn slag can reduce the need for hazardous chemicals used in hydrometallurgical refinement operations, as well as the extremely high temperatures required for pyrometallurgical processing. This is the first investigation into the feasibility of this novel approach, which includes direct investigations of the Pb-Zn slag feed using these alternative technologies. After extracting the valuable metals, the amorphous aluminosilicate part of the Pb-Zn slag can be reapplied as an alternative raw material in the building sector, adding to the circularity of the suggested approach..

In this study, a modular multi-step photometric microflow injection analysis (micro-FIA) system for the automatic determination of Cu(II) in a bioreactor has been developed. The system incorporates diverse 3D-printed modules, including a platform formed by a mixer module to mix Cu(II) with hydroxylamine which reduces Cu(II) to Cu(I) linked to a diluter module via a Tesla valve, a chelation mixer module, a disperser module, and a detector module provided by a LED light source at λ= 455 nm and a light dependence resistor (LDR) as a light intensity detector. The system measures the color intensity resulting from the chelation between Cu(I) and neocuproine. The micro-FIA system has demonstrated good capability for automatic and continuous Cu(II) determination, in a wide range of Cu concentrations from 34 to 2000 mg L-1. The device exhibits a good repeatability (coefficient of variation below 2% across the concentration range), good reproducibility, and has an accuracy of around 100% between 600 to 1900 mg·L-1. Real samples were analyzed using both the micro-FIA system and an atomic absorption spectroscopy method, revealing no statistically significant differences. Additionally, a Tesla valve located before the detector substituted a 3-way solenoid valve, eliminating the need for moving parts.

The aim of this investigation is focused on the effects of hooked-end steel fibers on both fresh and hardened properties of modified self-compacting concretes (SCC). For this purpose, the steel fibers are associated with other residues contents (i.e. marble, granite and rubber). This concatenated materials contents constitutes a novelty since no investigations are reported. It is found that the increase of rubber content, a better ability to absorb energy is observed. This indicates that a good alternative of structural material is provided. Fresh properties are evaluated by using flow, T500 time, V-funnel, J-ring methods. The mechanical behavior is evaluated in terms of compressive strength, tensile strength, static and dynamic modulus of elasticity, and damping ratio. Experimental results of the water absorption, porosity and density are also attained. It is also found that a SCC mixture containing steel fiber, marble/granite residue and rubber content is a potential mixture to be considered when in SCC designing associated with improved damping ratio. Although the rubber content decreases the mechanical behavior and slump flow, the concatenated utilization of MGR and steel fiber contents provide a slight improve in the damping result. An environmental benefit can also be associated since the cement consumption is decreased with marble additions.

E-waste management (EWM) refers to the operation-management of discarded or unproductive electronic devices and components, a challenge exacerbated due to overindulgent urbanization. This article presents a multidimensional cost-function-based analysis of the EWM framework structured on three modules - environmental, economic, and social uncertainties - which contemplate the 3 pillars of sustainability in an e-waste recycling plant, including the production-delivery-utilization process. The framework incorporates material recovery from a single e-waste facility provisioning for chemical and mechanical recycling. Each module is ranked using independent Machine Learning (ML) protocols: a) Analytical Hierarchical Process (AHP) and b) combined AHP and Principal Component Analysis (PCA). From a long list of possible contributors, the model identifies and ranks two key sustainability contributors to the EWM supply chain: overall energy consumption and volume of carbon dioxide generated. Another key finding is a precise time window for policy resurrection, which for the data considered, happens to be 400-600 days from the start of operation. Another interesting outcome is the quality of prediction using a combination of AHP and PCA, which consistently produced better results than any of these ML methods individually implemented. Model outcomes have been verified using a case study to outline a future E-waste sustained roadmap.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

The characteristics of excess aerobic granular sludge, related to its structure and chemical composition, limit the efficiency of anaerobic digestion. For this reason, pre-treatment methods and compositions with other organic substrates are used. The aim of the research was to determine the effects of co-digestion of pre-hydrodynamically cavitated aerobic granular sludge with waste fats on the efficiency of methane fermentation under mesophilic and thermophilic conditions. The addition of waste fats improved the C/N ratio and increased its value to 19. The greatest effects were observed in thermophilic anaerobic digestion at 55°C, where a 15% waste fat content in volatile soilds was ensured. This resulted in the production of 1278.2±40.2 mL/gVS biogas and 889.4±29.7 mL/gVS CH4. The CH4 content of the biogas was 69.6±1.3%. The increase in biogas and CH4 yield compared to pure AGS anaerobic digestion was 34.4% and 40.1%, respectively. An increase in the proportion of waste fats in the substrate had no significant effect on the efficiency of methane fermentation.

The global focus on geopolymer binder production has increased due to the adoption of waste materials and industrial byproducts. Given the gradual decline of the availability of fly ash and ground granular blast furnace slag (GGBFS) resulting from the decarbonization process in electricity and steel productions, waste clay brick powder (WCBP), could be a viable substitute of these pozzolanic by-products. This research is dedicated to thoroughly investigate the techno-eco-efficiency performance of WCBP when utilized as a geopolymer precursor. The favorable mechanical characteristics exhibited by fly ash-GGBFS-WCBP-based geopolymer binder emphasize the importance of assessing its sustainability alongside its technical viability. The study employed life cycle analysis (LCA), following ISO 14040-44 standards, and using the Simapro software, to evaluate the environmental implications of the use of WCBP-based geopolymer mixtures. Human toxicity emerged as the primary impact. Moreover, the analysis of life cycle costs highlighted key financial factors, with around 65-70% attributed to alkaline activators of the total cost. The production of alkaline activators was identified as a critical point for both environmental impact and economic considerations due to energy consumption. While WCBP-rich samples exhibit a 1.7-0.7% higher environmental impact compared to the control mix (CM), their high mechanical strength and cost-effectiveness make them technologically and economically efficient geopolymer mixes. In conclusion, the portfolio analysis for techno-eco-efficiency affirms that mixes containing 40%, 30%, and 20% WCBP are more efficient than those using 10% and 0% WCBP, respectively.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

New composite with core-shell structure based on magnesium hydride and finely dispersed aluminum powder with aluminum oxide shell was mechanically synthesized. We used magnesium chips to produce magnesium hydride and aluminum wire after exploitation to produce nano-sized aluminum powder. The beginning of the hydrogen release from composite occurred at the temperature of 117°C. The maximum desorption temperature from the MgH₂-EEWAl composite (10 wt.%) is 336°C compared to pure magnesium hydride – 417°C. The mass content of hydrogen in the composite is 5.5 wt.%. The positive effect of aluminum powder produced by the electric explosion of wires method on reducing the activation energy of desorption was demonstrated. Calculations showed that the activation energy of desorption for the composite is 106±1 kJ/mol, compared with pure magnesium hydride, whose activation energy was 155±2 kJ/mol. The results obtained make it possible to expand the possibility of using magnesium and aluminum waste for hydrogen energy.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

Rice cultivation is the main agricultural activity in Asia, and it results in an enormous amount of agricultural waste, that are usually disposed-off by burning, causing serious environmental health and climate problems. Pakistan is the tenth largest producer in the world and the fourth exporter of rice in the world. To date, there are no studies targeting Pakistan’s profile monitoring its contribution in open burning emissions from rice straw waste. This study presents the characterization of PCDD/Fs, PCBs and PAHs emissions from three samples of rice straw collected from the main rice cultivation regions of Pakistan (Punjab, Sindh and Azad Jammu and Kashmir) in relation to the role of metal-based agricultural additives. PCDD/Fs, PCBs and PAHs emissions were quantified using a fixed grid system biomass plant and measuring the macro-pollutants online and sampling the organic micro-pollutants and metals in isokinetic mode, followed by ISO and CEN standards methods. In addition, role of agrochemicals was monitored in terms of metal catalysis resulted in POPs emissions. This study provides the characterization of most relevant group of pollutants (metals, PCDD/Fs, PCBs and PAHs) as a result of agricultural waste combustion. The rice straw samples from AJK showed high values of organochlorine micro-pollutants compared to the values followed by samples from Punjab and Sindh, i.e., respectively, ∑PCDD/F (2594>1493>856 pg/Nm³) and ∑PCB (41>38>30 pg/Nm³). Whereas the organic micro-pollutants ∑PAH, indicators of incomplete combustion (PICs), were recorded high in the samples from Sindh followed by Punjab and AJK. This study supports the idea that the phenomena that lead to the formation of PCDD/F and PCB are influenced not only by poor combustion but also by the presence of metal catalysts or precursors in the burned fuel.

The aim of this study is to examine an efficient and environmental friendly process for hydrolyzing starch, an industrial-derived by-product of the potato processing industry, and to use the produced hydrolysates as substrates for methane production. A full factorial experiment was designed and the optimal concentrations of FeSO4·7H2O, H2O2 and temperature were determined obtaining a yield of 99.5%, with a total carbohydrates content equal to 28.65 g, when the input parameters were at their high level: FeSO4·7H2O 1.00g/L, H2O2 0.51 g/L and temperature 70.0oC. The hydrolysis kinetics were also examined revealing that temperature was the most important factor among the three optimization parameters. Furthermore, biodegradability tests were carried out to measure the methane production potential from the produced hydrolysates. The specific methanogenic activity was reached 0.669 g CODCH4/gVSS-day proving the effectiveness of the hydrolysis process and highlighting the potential of this food manufacturing by-product for bioenergy production. A preliminary cost analysis showed that a small investment for utilizing the starch in an existing wastewater treatment facility of a potato processing industry becomes profitable before the end of the 3rd year obtaining a NPV 37.5% higher than the NPV of the current utilization scenario.

The feasibility of using zeolites, synthesized from components found in municipal solid waste fly ash (MSW-FA), as sorbents for the recovery of nutrients (nitrate and phosphate) and heavy metals is critically assessed in this review. The inherent drawbacks of utilising a highly contaminated, variable, and relatively Al- and Si-dilute source such as MSW-FA to synthesize zeolites are discussed, and different methods to extract and decontaminate zeolite precursor materials from MSW-FA are considered. Ways to synthesize tailored zeolites and how their properties as well as the operational conditions impact the adsorption of cations such as ammonium and heavy metals are summarized. The use of surface-modified zeolites to adsorb nitrate and phosphate is also reviewed. And subsequently, approaches to utilise directly or recover for reuse the adsorbed compounds are considered, discussing potential challenges and mitigating measures related to leaching of unwanted compounds from the zeolites. Moreover, the possibility to regenerate the adsorption capacity of the zeolites for multiple adsorption cycles is considered. In the final chapter of the review a more general discussion of the main challenges and existing research gaps is provided, giving directions for recommended studies.

Bitumen is produced from non-renewable natural resources, continuously deplete and intrigues researchers to look for alternative binders. Annually, tons of waste engine oil (WEO) and crumb rubber (CR) are discarded unsustainably and pose a significant environmental threat. Adding these industrial waste products to asphalt provides a safe and cost-effective way for their disposal and improves the bitumen's performance in parallel. This study uses various combinations of waste engine oil and crumb rubber with 60/70 penetration grade bitumen to produce a partially synthetic bitumen. Adhesion being one of the critical characteristics of the bituminous binder has been assessed using the bitumen bond strength test along with physical and rheological properties. Results showed that waste engine oil with crumb rubber inclusion increases penetration and decreases the softening point, viscosity, complex modulus, and bonding strength. Additionally, polyphosphoric acid (PPA) in smaller dosages was also incorporated into the optimum percentage of CR + WEO to improve the properties of the binder. The results confirm that binder modification with waste engine oil and crumb rubber can be more effective with PPA. It is concluded that 35% of waste can replace the virgin binder giving a cost-effective and environmentally friendly solution.

The decentralized treatment of wastes is studied for an urban scenario considering a high-density population of 2500 inhab./km2. Food and garden waste were assumed to be treated in a co-digestion configuration using several mid-size digesters. In contrast biogas and digestate valorization were carried out in a centralized manner. Electricity and thermal energy were produced from this configuration, accounting for 1.3% of residential electricity demand and 3.2% of thermal demand when using double-turbocharged engines. However, the location of the treatment plants is a factor that may raise social discomfort. Rejection of locating the plant in specific sites close to residential neighbors, nuisance due to possible odor and gaseous emissions, and house market distortions are just a few of a long list of problematic aspects that may threaten the decentralized alternative. These factors are of great relevance and must be given a practical solution if the circular economic model is to be implemented by considering the insertion of waste streams into the production system and generating local energy sources and raw materials.

The extensive utilization of rebar during the construction of the project generates immense rebar waste, leading to increased construction costs and significant greenhouse gas emissions. Various approaches have been explored focusing on the minimization of rebar-cutting waste, such as optimizing cutting patterns, lap splice position, and special-length rebar utilization. Nonetheless, reducing rebar usage by minimizing the number of splices remains uninvestigated. In response to these issues, a two-stage optimization algorithm was developed, prioritizing special-length rebar to achieve near-zero rebar-cutting waste of less than 1% and concurrently reduce rebar usage, thereby promoting sustainable construction practices. The two-stage algorithm presented in this study involves the optimization of the lap splice position for the continuous rebar with a reduction of splices number. Furthermore, it integrates a special-length minimization algorithm for the additional rebars. Applying the algorithm to beam structures in a small-sized factory building project led to a notable reduction of 29.624 tons of rebar, equivalent to 12.31% of the total purchased quantity. Greenhouse gas emissions were reduced by 102.68 tons, and associated costs decreased by USD 30,256. A rebar-cutting waste of 0.99% which is near zero was achieved. These findings highlight the significant potential of the proposed algorithm in reducing rebar waste and facilitating sustainable construction practices. In addition, the application of the proposed algorithm in reinforced concrete construction projects will amplify the associated advantages accordingly.

Brewers’ spent grain (BSG) is an important waste produced in beer companies with a high po-tential to be transformed into commercial by-products. The present paper reports a forecasting technology study with the aid of bibliographic review and patent analysis tools aiming to in-vestigate the maturity of certain technologies, considering the use of BSG on a closed-loop bio-refinery and circular bioeconomy concept integrated into a brewery. To evaluate the possibili-ties of production of high-added value products in Brazil, it was presented an overview of BSG’s scientific, technological, and marketing products and applications. The comparison between numbers of articles versus patents shows that the solutions proposed by research articles are not being transformed into maturated viable technologies. The results suggest that there is a gap between the scientific research in the institutions and their applications in industry, which lead to the destination of the BSG for more economically attractive investments when compared to research in Brazil. Ultimately, from the carried-out analysis, it was possible to propose a brew-ing process connected to the biorefinery system, showing the possibility to the newly arising brewery industries.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

Despite the development of biorefinery processes, so far this area does not take into account the possibility of coupling the “conventional” composting process with the production of biochemicals. However, net carbon monoxide (CO) production has been observed during bio-waste composting. So far, O2 concentration and temperature have been identified as main variables influencing CO formation. This study aimed to investigate the CO net production during bio-waste composting under controlled laboratory conditions, depending on different aeration rates and temperatures. A series of composting processes were carried out in conditions ranging from ~psychrophilic to thermophilic (T=35, 45, 55, and 65°C) and an aeration rate of 2.7, 3.4, 4.8, and 7.8 L‧h-1. The highest concentrations of CO in each thermal variant was achieved with oxygen deficit (aeration rate 2.7 L‧h-1); additionally, CO levels increased with temperature, reaching ~300 ppm at 65°C. Production of CO in mesophilic and thermophilic conditions draws attention to the biological CO formation by microorganisms capable of producing the CODH enzyme. Further research on the CO production efficiency in these thermal ranges is necessary with the characterization of the microbial community and analysis of the ability of the identified bacteria to produce the CODH enzyme and convert CO from CO2.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

Over the past few decades, the quantity of construction waste has steadily risen in tandem with the expansion of construction activities and the rapid pace of development and urbanization. This problem is rooted in the practice of delivering materials to construction sites without totally using them for their intended purpose. The primary aim of the JIT tactic is to ensure that the precise materials required for production are available at the precise location, exact time, and appropriate quantity, thereby facilitating timely production. Presently, the use of ready-mix concrete is the most typical instance of a just-in-time construction process Developed countries have benefitted immensely from the use. However, the reverse is the case in developing countries like Nigeria, where indigenous contractors still employ traditional in-situ concreting even when faced with restrictive site space. This study focuses on investigating Ready-mix concrete, to project its immense benefits and effectiveness in minimizing lean construction waste. A survey research design and case study were adopted for this study, with the population being the management staff of construction firms in Lagos State, Nigeria. The questionnaire was used to collect data and the targeted respondents were purposively selected from the population. A total number of 112 questionnaires were administered with a response rate of 51%. Percentage, mean, standard deviation, and ANOVA were used to analyze the data. The mean value is above 3 on a Likert Scale of 5, while faster construction speed and uniform quality of concrete are the topmost benefits derived from adopting Ready-mix Concrete in Nigeria. The Case study also revealed the effectiveness of Ready-mix concrete in minimizing the two lean construction wastes that were examined, namely; waste of overproduction and waste of waiting. It is recommended Just-in-Time technique should be extended to other construction materials aside from concrete to improve waste minimization through the adoption of an overall JIT policy for the construction process.

The Metabolic Food Waste [MFW (kg of food)], first time developed in 2016 as a new indicator by Serafini and Toti, indicates the amount of food consumed over the nutritional requirements and the impact of this overconsumption on the environment. It is necessary to identify the causes and to develop potential methods to prevent and reduce MFW, at the same time with increasing consumer awareness about unsustainable diets and changing diet habits toward more environmentally conscious consumption patterns. By analysing and corroborating external data available for food waste, nutritional requirements, environmental impact of food waste and consumer behaviour, we identified as primary causes for MFW the lack of nutritional education and little understanding of the nutritional requirements amongst all categories of consumers, no access to appropriate food resources or reduced availability of fresh produced food. We conclude that for the quantification of the negative impact of MFW on both the environment and human health, we need a decisive action to raise consumer awareness for healthy and sustainable diets, together with an uniform worldwide distribution of the nutritious food.

An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

One of the potential sources of rare-earth elements (REEs) is the solid waste from alumina industry - bauxite residue, known as “red mud” (RM). The main REEs from the raw bauxite are concentrated in RM after the Bayer leaching process. The earlier worldwide studies were focused on the scandium (Sc) extraction from RM by concentrated acids to enhance the extraction degree. This leads to the dissolution of major oxides (Fe2O3 and Al2O3) from RM. This article studies the possibility of selective Sc extraction from alkali fusion red mud (RMF) by diluted nitric acid (HNO3) leaching at pH ≥ 2 to prevent co-dissolution of Fe2O3. RMF samples have been analyzed by X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), electron probe microanalysis (EPMA), and inductively coupled plasma mass spectrometry (ICP-MS). Sc extraction has been found to be 71.2 % at RMF leaching by HNO3 at pH=2 and at 80 °C during 90 min. The kinetic analysis of experimental data by the shrinking core model has shown that Sc leaching process is limited by the interfacial diffusion and the diffusion through the product layer. The apparent activation energy (Ea) was 19.5 kJ/mol. We have established that according to EPMA of RMF, Sc is associated with iron minerals; it could act as the product layer. The linear dependence of Sc extraction of magnesium (Mg) extraction has been revealed. This fact indicates that Mg can act as a leaching agent of Sc presented in RMF by ion-exchangeable phase.

A winemaking waste was used as a precursor of activated carbon used in hazardous Cr(VI) removal from solutions. The preparation process consisted of a hydrothermal process, and a chemical activation, of the resulting product, with KOH. The adsorption results showed that the adsorption of Cr(VI) on the obtained activated carbon is strongly dependent on the stirring speed applied to the carbon/solution mixture, pH of the solution, and temperature. The equilibrium isotherm was well fitted to the Langmuir type-II equation, whereas the kinetic can be described by the pseudo-second-order kinetic model. Thermodynamic studies revealed that Cr(VI) adsorption was an exothermic and spontaneous process. Finally, desorption experiments showed that Cr(VI) was effectively desorbed using hydrazine sulfate solutions, and at the same time, the element was reduced to the less hazardous Cr(III) oxidation state.

One way to increase overall natural gas engine efficiency is to transform exhaust waste heat into useful energy by means of a bottoming cycle. Organic Rankine cycle (ORC) is a promising technology to convert medium and low grade waste heat into mechanical power and electricity. This paper presents an energy and exergy analysis of three ORC-Waste heat recovery configurations by using an intermediate thermal oil circuit: Simple ORC (SORC), ORC with Recuperator (RORC) and ORC with Double Pressure (DORC), and Cyclohexane, Toluene and Acetone have been proposed as working fluids. An energy and exergy thermodynamic model is proposed to evaluate each configuration performance, while available exhaust thermal energy variation under different engine loads was determined through an experimentally validated mathematical model. Additionally, the effect of evaportating pressure on net power output , absolute thermal efficiency increase, absolute specific fuel consumption decrease, overall energy conversion efficiency, and component exergy destruction is also investigated. Results evidence an improvement in operational performance for heat recovery through RORC with Toluene at an evaporation pressure of 3.4 MPa, achieving 146.25 kW of net power output, 11.58% of overall conversion efficiency, 28.4% of ORC thermal efficiency, and an specific fuel consumption reduction of 7.67% at a 1482 rpm engine speed, a 120.2 L/min natural gas Flow, 1.784 lambda, and 1758.77 kW mechanical engine power.

Most of the municipalities in the Gulf region are facing performance related issues in their municipal solid waste management (MSWM) systems. They lack to possess a deliberate inter-municipality benchmarking processes. Instead of identifying the performance gaps for their key components (e.g., personnel productivity, operational reliability, etc.) and adopt proactive measures, the municipalities primarily rely on an efficient emergency response. A novel hierarchical modeling framework, based on deductive reasoning, is developed for performance assessment of MSWM systems. Fuzzy rule based modeling using Simulink-MATLAB was used for performance inferencing at different levels, i.e., component, sub-components, etc. The model is capable of handling the inherent uncertainties due to limited data and imprecise knowledge base. The model’s outcomes can exclusively assist the managers working at different levels of organizational hierarchy for effective decision-making. Performance of the key component, assists the senior management to assess the overall compliance level of performance objectives. Subsequently, operation management can hone in the sub-components to acquire useful information for intra-municipality performance management. While, individual indicators are useful for inter-municipality benchmarking. The model has been implemented on two municipalities operating in Qassim Region, Saudi Arabia. The results demonstrate the model’s pragmatism for continuous performance improvement of MSWM systems in the country and elsewhere.

In the industrial production of olive oil, both solid wastes and those produced from their incineration are a serious environmental problem since only 20% w/w of the fruit becomes oil and the rest is waste, mainly orujo and alperujo. A key aspect to transform these wastes into an important source of energy such as pellets is to recognize the most appropriate time of the year for waste drying, with the objective of minimizing the environmental impact of the volatile compounds contained in the waste. In this work, the emissions produced during thermal-mechanical drying were studied along a period of six months of waste storage in which alperujo and orujo were stored in open containers under uncontrolled environmental conditions. The studied emissions were produced when both wastes were dried in a pilot rotary drying trommel at 450ºC to reduce their initial humidity of around 70-80% w/w to 10-15% w/w. Results indicated that when the storage time of the wastes in uncontrolled environments increases, the emission of odorant compounds during drying also increases as a consequence of the biological and chemical processes occurring in the containers during waste storage. The main odorant VOCs were quantified monthly for six months at the outlet of the drying trommel. It was determined that the drying of this type of waste can be carried out properly until the third month of storage. Afterwards, the concentration of most VOCs produced widely exceeded the odor thresholds of selected compounds.

Efficient use of agricultural wastes and by-products, basically transforming waste materials into value added products, is considered as pivotal for an effective bioeconomy strategy for the rural development. To this scope, citrus waste management represents a major issue for citrus processors but, at the same time, it embodies a potentially unexploited resource for the rural sustainable development. This study focuses on analyzing the current management of citrus waste in South Italy and identifying the determinants and barriers that may affect an entrepreneur’s choice on the destination of citrus waste. Citrus processors’ preferences about the contract characteristics needed to take part in a co-investment scheme have been investigated. Both analyses are preliminary steps to design an innovative and sustainable citrus by-product supply chain. Results show that the distance between the citrus processors and the citrus by-products plant is one of the main criteria for choosing alternative valorization pathways. Moreover, the required guaranteed capital, the short duration of the contract, and low risk are contract scheme characteristics that improve entrepreneurs’ willingness to co-invest in the development of a citrus waste multifunctional plant.

DR2B and DR2C extracts, from peel of commercially and physiologically ripe eggplants, were studied for the antioxidative cytoprotective properties and anti-HSV-1 activity, in line with the evidence that several antioxidants can impair viral replication by maintaining reducing conditions into the host cells. The antioxidative cytoprotective effects against tBOOH-induced damage was assessed in Caco2 cells, while the antiviral activity was studied in Vero cells; phenolic and anthocyanin fingerprint was characterized by integrated phytochemical methods. Results highlighted different compositions of the extracts, with chlorogenic acid and delphinidin-3-rutinoside as the major constituents; other peculiar phytochemicals were also identified. DR2C resulted able to partly counteract the tBOOH-induced cytotoxicity, with a remarkable lowering of lactate metabolism under both normoxia and hypoxia. DR2B and DR2C reduced ROS production, possessed scavenging and chelating properties. Interestingly, DR2C increased intracellular GSH levels. Furthermore, DR2C inhibited the HSV-1 replication when added for 24 h after viral adsorption, as also confirmed by the reduction of many viral proteins expression. Since DR2C was able to reduce NOX4 expression during HSV-1 infection, its antiviral activity may be correlated to its antioxidant properties. Although further studies are needed to better characterize DR2C activity, the results suggest this extract as a promising new anti-HSV-1 agent.

The efficiency of cold steel rolling depends mainly on the quality of the metal-working coolant (MWC) and its cost. In this connection, it is actual to search for new compositions of lubricants and emulsions, which provide the lowest values of the friction coefficients in deformation zone and are obtained by waste recycling in other industries. In this study we have developed new compositions of the MWC on basis of mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The new compositions of MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 100 mm. The efficiency of new MWC during cold rolling of brass L63 samples was determined by factor of metal stretch forming λ. We found the new metal-working coolants to show the most efficiency under higher cobbing that provides the highest metal stretch forming. The composition with 30 % of mono- and diglycerides is the most effective because it provides the minimum coefficient of friction that leads to increase of factor of metal stretch forming. Thereby the metal-working coolants on basis of mono- and diglycerides obtained from the wastes of sunflower oil production can be recommended for use in strip rolling of copper-zinc alloys because of a low cost, availability and high efficiency.

Our findings illustrate that CS should be employed as a means of popularizing scientific output, facilitating the promotion of political decision-making processes, and acting as a knowledge broker to reverse consumer behavior towards more environmentally friendly and conducive to SUP usage.

Focusing on the COVID-19 period in Japan, this study identifies the effectiveness of a municipal unit-based pricing (UBP) system on household waste reduction through a panel data analysis targeting 770 cities for 2013–2022. It focuses on simple unit pricing (SUP) and two-tiered pricing (TTP) systems as the UBP components. As previous studies have not considered the COVID-19 period when assessing UBP, this study significantly contributes to the literature by providing new evidence. The main findings are as follows: First, SUP effectively reduced household waste during the COVID-19 period, although its effectiveness was slightly neutralized owing to the pandemic environment. Second, TTP efficiently restrained household waste during the COVID-19 period, when people became cautious about their excessive waste volumes beyond the TTP criteria. The study implicates the need to expand the municipal adoption of the UBP system for household waste reduction.

(1) Food banks have played an important role in reducing food losses and waste and improving the food insecurity situation of vulnerable people. This study aims to conduct a systematic review of food bank evaluation studies and bring new perspectives for future research and decision-making. (2) 58 articles were selected and analyzed from a survey on the Web of Science and Science Direct Platforms. Bibliometric analyses and analyses of the evaluation methodologies used were presented. (3) The bibliometric results indicate an internationalization of the studies since 2013, with a focus on developed countries, and a direct relationship between the location of the research institutes and the location of the organizations studied. Analysis of evaluation methodologies showed that the main aspects evaluated are related to long-term impact, short-term impact and results, indicating less interest in the internal processes and activities of organizations. This result raises important questions for researchers and decision-makers: to what extent evaluation studies reflect the reality and context of a given country or region and to what extent evaluation studies reflect the management processes of food banks.

Methylene blue (MB) is a dye hazardous pollutant widely used in several industrial processes that represents a relevant source of water pollution. Thus, the research of new systems to avoid its environmental dispersion, represents an important goal. In this work, an efficient and sustainable nanocomposite material based on green gold nanoparticles for MB water remediation, was developed. Starting from reducing and stabilizing characteristics of compounds naturally present in Lambrusco winery waste (grape marc) extracts, green gold nanoparticles (GM-AuNPs) were synthesized and deposited on a supporting membrane to create an easy and stable system for water MB decontamination. GM-AuNPs, with a specific plasmonic band at 535 nm, and the modified membrane were firstly characterized by UV-vis spectroscopy, X-Ray diffraction (XRD), and electron microscopy. Transmission electron microscopy analysis revealed the presence of two breeds of crystalline shapes, triangular platelets and round-shaped pentatwinned nanoparticles, respectively. The crystalline nature of GM-AuNPs was also confirmed from XRD. The photo-catalytic performance of the modified membrane was evaluated under natural sunlight radiation obtaining a complete MB degradation (100%) in 116 minutes. A pseudo-first-order kinetic described the photocatalytic process with a rate constant k equal to 0.044 ± 0.010 min-1. The modified membrane demonstrated high stability since it was reused, without any treatment, for 3 months and for at least 20 cycles maintaining the same performances. GM-AuNPs-based membrane was also tested with other water pollutants (methyl orange, 4-nitrophenol and rhodamine B revealing a high selectivity towards MB.

Mixed plastic packaging waste sorting residues (MPO323) were treated by thermal pyrolysis to utilize pyrolysis oil and char. The pyrolysis oil was found to contain aromatic and aliphatic hydrocarbons. Chlorine and bromine contents were up to 40,000 mg/kg and 200 mg/kg, respectively. Additionally, other elements like sulfur, phosphorous, iron, aluminum, and lead were detected, which can be interpreted as impurities regarding the utilization of the oils by means of chemical recycling. The pyrolysis char showed high contents of potentially active species like silicon, calcium, aluminum, iron, and others. To enhance the content of aromatic hydrocarbons and to reduce the level of contaminants, the pyrolysis oil was reformed with the corresponding pyrolysis char to act as an active material in a fixed bed. The temperature of the reactor and the flow rate of the pyrolysis oil feed were varied to gain insights on cracking and reforming reactions as well as on the performance with regard to decontamination.

A major problem of the technological production process of the metallurgical-grade silicon is formation of a large amount of microsilica. However, this material can be a significant source of raw materials for its own production. Hence, this study is aimed to solve the problem of micro-silica utilization, i.e. the technogenic dust-like waste generated during the melting of the technical-grade silicon. Within this study, the technology of the joint briquetting of microsilica was investigated with the carbonaceous reducing agents, i.e. by obtaining of mono-charge and by melting of the technical-grade silicon from the obtained mono-charge in the 200kVA ore-thermal furnace. Results of the study show that the briquettes in the melting process of the technical-grade silicon can be used in the range from 0 to 50%. The using of briquettes may significantly improve the technological parameters. When briquetted charge is applied only, the technological parameters will deteriorate significantly. The material balance of silicon melting showed the recovery rates of the main elements (Si, Al, Ca and Fe). It recorded a decrease in content of aluminum from 1.9-2.1% to 0.5-0.7%, calcium from 0.2-0.3% to 0.07-0.1% and titanium from 0.2-0.23% to 0.11-0.13% during the transition to briquetted monocharge. Phosphorus content increased from 0.004-0.005 to 0.011-0.013%.

The clothing industry is a hotbed for exploitative working conditions and environmental damages, of which affluent global North countries remain a substantial driver. The circular economy is a potential solution to these issues, but its social implications remain unclear. Using the UK as a case study, this article analyses the global social impacts of a transition to circular clothing economies in the global North, finding these to be (almost) entirely dependent upon the intentions and design of the associated politics. Some aspects of a transition will be unambiguously good for some people; others will only be beneficial with careful governance. Moreover, entrenched global economic inequalities leave trade-offs borne largely by the global South, highlighting the need for circular economy research – its drive for localisation notwithstanding – to look globally to consider how a fair transition can be achieved.

The current scenario of radioactive waste management requires innovative and automated solutions to ensure effectiveness and safety. In response to this need, the PI3SO (Proximity Imaging System for Sort and Segregate Operations) project was proposed. It is a gamma radiation proximity scanner system for radioactive waste with the primary goal of speeding up some aspects of the waste management cycle while reducing direct human operations. The system will provide proximity imaging for hot spot finding and spectral analysis for radiological characterization, enabling semiautomatic recognition, sorting and separation of radioactive waste. The core of the proposed scanning system consists of an array of 128 CsI(Tl) scintillators, 1 cm3 size, coupled with silicon photomultipliers (SiPM), installed on a motorized bridge sliding along a suitable table in order to scan the materials under investigation.

The circular economy is one of the main strategies for mitigating the environmental impacts of civil construction, due to the generation of construction and demolition waste (CDW). In this transition, evaluating alternatives for using buildings as material banks is a way to make the process of reusing construction components more efficient. Thus, the article aimed to evaluate the state of the art of publications on the relationship between the circular economy in civil construction and the conceptual model of buildings as material banks, to mitigate the environmental impacts of CDW. The authors chose the methodological design of Systematic Literature Review, using the Scopus and Web of Science databases for research, with the following search strings: ("construction" or "civil construction" or "built environment" or "construction industry" ) and ("circular economy" or "circular construction") and ("material banks" or "BAMB" or "buildings as material banks" or "building stocks" or "building materials") and ("construction waste" or "demolition waste" or "CDW" or "construction and demolition waste" or "environmental impacts"). After a screening in which only articles published in journals were selected, from 2013 to 2023, inclusion and exclusion criteria were applied, to evaluate only those that had a direct relationship with CDW management through circular economy strategies and buildings such as banks of material. As a result, 93 articles remained, which were analyzed using quantitative and qualitative approach. The quantitative results showed an increase in publications since 2020, which are concentrated in European countries and China. The predominance of applied studies was also noted, through case studies that evaluate the management of materials and waste in the urban environment. The qualitative analysis, carried out using a SWOT Matrix, highlighted the strengths of the buildings, such as material banks, the potential reduction of resource extraction and urban mining, promoting the circulation of construction products. However, the recycling of waste, such as aggregates, still stands out as the main end-of-life strategy adopted, even without occupying the top of the waste hierarchy.

There are various approaches to managing polyethylene terephthalate waste, including methods for recycling PET. However, at present, only the cleanest wastes that can already be efficiently recycled using known methods are considered in the scientific literature. The study aims to look at other forms of polyethylene terephthalate waste that pose a challenge: low quality PET flakes, polyester tire cord, PET dust and prepolymer waste. The waste was characterized by FTIR spectroscopy, viscosimetry, differential scanning calorimetry, laser diffraction and sieve analysis. The findings describe the composition and properties of various forms of polyethylene terephthalate waste. Low quality PET flake waste and polyethylene terephthalate dust have been shown to be suitable for all chemical recycling methods. When recycling waste polyester tire cord, it is difficult to completely separate the rubber, so its presence in the final product must be taken into account. The most promising way to process a prepolymer is its depolymerization by hydrolysis, alcoholysis or glycolysis to produce monomers for the synthesis of PET, similar in properties to the primary one.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Printed circuit boards (PCBs) make up 3 to 5% of all electronic waste. The metal content of spent PCBs can reach 40%. They usually contain valuable metals - Ag, Au, Pd, as well as other metals such as Cu, Sn, Pb, Cd, Cr, Zn, Ni and Mn. However metallic part of whole PCB is 40-60% including Cu layers between the fiberglass-polymer layers. The paper describes economics of the the valuable metals (Ag, Au, Pd) containing concentrate preparation from raw PCB. Considered the influence of pre-treatment method of PCB before the extraction of valuable metals on the extraction self-cost change. The disintegration method is based on the high-energy impact of the particles of the material to be ground, thus causing the separation of the metallic components of the PCB. In the course of the work, single and double direct grinding by the method of disintegration was studied. For the calculation the test batch 10’000 kg of two types of PCB were taken for estimation of the self costs and potential profit in case of complete valuable metals (Ag, Au, Pd) plus Cu extraction. Is shown that from 10’000 kg of studied PCB is possible to obtain 1144 and 1644 kg of metal-rich concentrate, which further should be subjected to electro-hydrochlorination for metals leaching. The main findings shows, that despite of high content of Cu in studied PCB, the commercial value is insignificant in total income from the Ag, Au and Pd sale. Was established correlation of the self-cost decrease after separative disintegration of PCB by metal content increase (by specific metals such as Au, Ag, Pd and also Cu) with the metal potential yield after extraction.

The Indorama Eleme Petrochemical Limited (IEPL) is found in the southern part of Nigeria more specifically on the Rivers State southern religion Nigeria. It consists of five distinct units, each of which generates its own unique trash at a rate of around 3115.98 tonnes per year. This study had the goal of concentrating on the management of the processing wastes in order to minimize the negative effects that they have on the environment. It is necessary to have an understanding of the number, nature, and make-up of IEPL's industrial wastes in order to effectively manage and regulate the development of waste there. As a result, we decided to collect data through the use of questionnaires. The classification of industrial wastes was accomplished by doing a comparative study and synthesis of research that were relevant to the management of petrochemical waste. Because an individual coding system is required for the integrated management of industrial waste, we gave each type of trash a code that consists of thirteen digits. The primary components of trash were catalysts (9.58 percent), metallic materials (7.62 percent), plastic barrels (35.77 percent), coke (12.66 percent), wood (4.47%), oil (4.15%), glass (0.028 percent), cooling tower packaging (6.7 percent), and other material (18.83 percent). According to the findings of the investigation into the physical qualities of the wastes, only 11.81% of these residues were liquid, while 88.19% were solid. The current handling of these wastes has been experiencing significant difficulties as of late. garbage management at IEPL was particularly challenging due to the wide variety of wastes produced there and the dangerous nature of the wastes themselves (88.19% of garbage was hazardous waste). Recycling and reuse of garbage may have been the greatest decision in some situations; yet, incineration and disposal of waste are also necessary options.

The production of photovoltaic modules is increasing to reduce greenhouse gas emissions. However, this results in a significant amount of waste at the end of their lifespan. Therefore, recycling these solar panels is important for environmental and economic reasons. However, collecting and separating Crystalline silicon, Cadmium Telluride, and Copper indium gallium selenide panels can be challenging, especially in underdeveloped countries. The innovation of this work is to develop a process to recycle all solar panel waste. The dissolution of all metals is studied through the leaching process as the main step of the flowchart. In the first step of leaching, silver can be recovered 98% by 0.5 nitric acid. Then, the second and third step involves the use of glycine for base metals dissolution, followed by the leaching of valuable metals with hydrochloric acid. The effect of parameters such as initial pH, acid concentration, solid/liquid ratio, and Hydrogen peroxide concentration are studied. The results show that Cu, Pb, Sn, Zn, Cd, In, Ga, and Se can be recovered until about 100% under optimal conditions. The optimal conditions for the dissolution of Cu, Zn, and Cd were the glycine concentration of 0.5 M, Temperature of 25 ˚C, the solid/liquid ratio of 10 gr/l, and 1% of Hydrogen peroxide. The optimized glycine concentration for the leaching of lead and tin was 1.5M. Indium and gallium were recovered to 100% by the use of 5M Hydrochloric acid, S/L=10gr/l, and T=45 ˚C. Separation of selenium and tellurium occurred by 0.5 M HCl at a temperature of 60 ˚C. Additionally, for the first time, a general outlook for the recycling of various end-of-life solar panels is suggested.

The Atlantic cod (Gadus morhua) and red king crab (Paralithodes camtschaticus) processing wastes are massive and unutilized in the Murmansk region of Russia. The samples of skin-containing waste of Atlantic cod fillets production were hydrolyzed using enzyme preparations derived from red king crab hepatopancreases, porcine pancreases and Bacillus subtilis bacteria. The activity of enzymes from crab hepatopancreases was significantly higher than the activity of enzymes derived from other sources. The optimal conditions of the hydrolysis process have been figured out. The samples of cod processing waste hydrolysate were analyzed for amino acid composition and molecular weight distribution. The samples of hydrolysate were used as core components for bacterial culture medium samples. The efficiency of the medium samples was tested for Escherichia coli growth rate; the most efficient sample had efficiency 95.3% of that of a commercially available medium based on fish meal. Substitution of medium components with those derived from industrial by-products is one of the ways to decrease a cost of a culture medium in biopharmaceutical drug production.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.

The use of natural stone has a historical and environmental value that makes it strategically valuable for landscape conservation in Europe. Marble, among others, is widely spread on Earth, and it offers high-performance features in architectural applications. However, the complexity of these formations and the rock variability in different ore bodies require detailed studies of the natural and induced stress state, the fracturing degree, and the influence of external factor (such as temperature and/or chemical agents) on the mechanical properties in order to optimize the exploitation processes by reducing extractive waste. This article shows a series of studies conducted by the authors over the last 20 years aimed at making the exploitation of marble blocks in the Carrara basin safer, more efficient, and, therefore, more sustainable. In particular, studies for increasing the knowledge on the natural and the induced stress state through on-site measurements and numerical modeling, studies to improve the quality of the exploited material through improvements of cutting technologies, studies to improve the knowledge of the mechanical behavior of the material under varying loads and temperature conditions and studies to improve the reuse of water materials and their reduction are reported.

Relying on the United Arab Emirates (UAE) extract from the cross-national data sample on the environmental affection and cognition of adolescent students, and seemingly unrelated bivariate weighted ordered probit regression modeling, this study adopts a national perspective to investigate the determinants of adolescent students' awareness and expectations about nuclear power technology and nuclear waste in the UAE. Identification of model parameters is achieved through maximum simulated likelihood estimation. The findings show that each level increase in UAE youth's interest in ecosystem services and sustainability raises their awareness of nuclear electrical power and nuclear waste by 13.5%, while reducing by 2.4% their level of optimism towards the technology. Furthermore, we find significant heterogeneity in youth awareness and expectations about nuclear power technology across the seven Emirates. Accounting for all other factors (including interest in ecosystem services), UAE youth awareness about nuclear electrical power technology appears to not significantly influence their expectations about the evolution of this technology for the next 20 years. Given that the UAE first nuclear power plant ``Barakah'' is scheduled to start operations end of 2019 beginning 2020, and the typical long life-span of nuclear wastes, our results provide important insights for developing sustainable nuclear energy policies and establishing a long-term nuclear energy program in the UAE.

Associating the most influential parameters with the product distribution is of uttermost importance in complex catalytic processes such as fluid catalytic cracking (FCC). These correlations can lead to the information-driven catalyst screening, kinetic modeling and reactor design. In this work, a dataset of 104 uncorrelated experiments, with 64 variables, has been obtained in an FCC simulator using 6 types of feedstock (vacuum gasoil, polyethylene pyrolysis waxes, scrap tire pyrolysis oil, dissolved polyethylene and blends of the previous), 36 possible sets of conditions (varying contact time, temperature and catalyst/oil ratio) and 3 industrial catalysts. Principal component analysis (PCA) has been applied over the dataset, showing that the main components are associated with feed composition (27.41% variance); operational conditions (19.09%) and catalyst properties (12.72%). The variables of each component have been correlated with the indexes and yields of the products: conversion, octane number, aromatics, olefins (propylene) or coke, among others.

In this paper, an improved system to efficiently utilize the low-temperature waste heat (WHUS) from the flue gas of coal-fired power plants is proposed based on heat cascade. The essence of the proposed system is that the waste heat of exhausted flue gas is not only used to preheat air for assisting coal combustion as usual but also to heat up feedwater and the low-pressure steam extraction. Preheated by both the exhaust flue gas in the boiler island and the low-pressure steam extraction in the turbine island, thereby part of the flue gas heat in the air preheater can be saved and introduced to heat the feedwater and the high-temperature condensed water. Consequently, part of the high-pressure steam is saved for further expansion in the steam turbine, which obtains additional net power output. Based on the design data of a typical 1000 MW ultra-supercritical coal-fired power plant in China, in-depth analysis of the energy-saving characteristics of the optimized WHUS and the conventional WHUS is conducted. When the optimized WHUS is adopted in a typical 1000 MW unit, net power output increases by 19.51 MW, exergy efficiency improves to 45.46%, and net annual revenue reaches 4.741 million USD. In terms of the conventional WHUS, these aforementioned performance parameters are only 5.83 MW, 44.80% and 1.244 million USD, respectively. The research of this paper can provide a feasible energy-saving option for coal-fired power plants.

This study aims to explain individual engagement in sustainable waste management behaviors (SWMBs) based on the application of protection motivation theory (PMT). SWMBs include waste avoidance, green purchasing behavior, reuse and recycle, and waste disposal behaviors. This study applies PMT to explore how individuals’ SWMBs are influenced by their perceived threats caused by environmental contamination from waste disposal and their perceived coping capability. The Bangkok metropolitan area was selected as a case study because it has faced serious waste management problems caused by massively increasing amounts of solid waste during the last ten years. Questionnaire surveys were conducted with 193 public and private officers residing in the city of Bangkok. The one-way analysis of variance (ANOVA) was performed to justify the effect of individual threat appraisal and coping appraisal on the engagement in SWMBs. The results demonstrated that respondents’ self-efficacy highly influenced all types of SWMBs. The perceived probability of being impacted from pollutants influenced all of the SWMBs except green purchasing behaviors. Response efficacy did not influence all SWMBs; however, the perceived severity of adverse consequences caused by pollutants highly influenced reuse and recycle behaviors. It could be suggested that PMT is well suited for investigating low-cost and simple SWMBs. It could also be suggested that different communication campaigns should be established to enhance citizens’ engagement in each type of SWMB.

This study examines the chemical recycling of polymethylmethacrylate (PMMA) dental waste via pyrolysis in a semi-batch fixed-bed reactor, aiming to convert it into the valuable monomer methyl methacrylate (MMA). Experiments were conducted in a 2L reactor at temperatures of 425 °C, 450 °C, and 475 °C to understand the effects of heating rate and temperature on product yield and composition. Results show that at 425 °C, MMA was the primary liquid component, with minimal by-products, suggesting that lower temperatures enhance monomer recovery. Higher temperatures, however, increased gas yields and reduced MMA yield due to intensified thermal cracking. The study also highlights that char formation and non-condensable gases increase with reactor scale, indicating that heat transfer limitations can influence MMA purity and yield. These findings emphasize that for effective MMA recovery, lower temperatures and controlled heating rates are optimal, especially in larger reactors where heat transfer issues are more prominent. This research contributes to scaling up PMMA recycling processes, supporting industrial applications to achieve efficient monomer recovery from waste.

This study analyzes the elemental and oxide compositions of three selected agricultural residues—Dried Pawpaw Leaves (DPL), Kolanut Pod (KNP), and Sweet Orange Peel (SOP)—for their potential as heterogeneous catalysts. Energy Dispersive X-ray (EDX) analysis identified calcium (25%) and potassium (29%) as the primary elements in DPL and KNP, with calcium oxide (CaO) and potassium oxide (K2O) as the dominant oxides. SOP had a similar composition but lacked vanadium. Calcined residues were analyzed at temperatures ranging from 500°C to 900°C using X-ray Fluorescence (XRF), revealing stable silicon dioxide (SiO2) content and temperature-dependent variations in CaO and K2O, indicating their catalytic potential for transesterification processes. Scanning Electron Microscopy (SEM) showed non-uniform, spongy microstructures, enhancing the surface area and catalytic efficiency. Fourier Transform Infrared Spectroscopy (FTIR) identified functional groups essential for catalytic activity, such as hydroxyls, methyl, and carboxyl. X-ray Diffraction (XRD) confirmed the presence of crystalline phases like calcium carbonate and calcium oxide, crucial for catalytic performance. Experimental biodiesel production using a mixture of the calcined residues (33.33% each of KNPA, SOPA, and DPLA) resulted in the highest biodiesel yield at 65.3%. Model summary statistics, including R² (0.9824) values and standard deviations (0.0026), validated the experimental design, indicating high precision and prediction accuracy. These results suggest that the selected agricultural residues, when calcined and mixed properly, can serve as effective heterogeneous catalysts, with significant implications for biodiesel production, supporting previous research on the importance of calcium in catalytic processes.

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FR). Significant amounts of FR are usually required to effectively affect the polymer burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC) and pentaerythritol (PER) and its composites containing additionally short basalt fibers (BF). Composites manufactured by twin-screw extrusion were subjected to four reprocessing cycles by injection molding, comprehensively analyzing structural, mechanical, and fire behavior changes in each cycle. The obtained results confirmed the safety of using the proposed flame-retardant system for polyamide, processed under the recommended process parameters, without the risk of significant changes in the structure despite the partial increase in flammability caused mainly by the degradation of the polymer.

The “circular bioeconomy” offers numerous opportunities for the health, cosmetic, and nutrition sectors through the potential reuse of Castanea sativa by-products. This abundant and sustainable resource provides valuable bioactive secondary metabolites with antioxidants and anti-inflammatory properties. The transformation of these by-products into high-value products for human health can contribute to sustainable economic growth and reduce the environmental impact of traditional waste disposal practices, thus creating added value from previously underutilized resources. In the present study, we investigated the antioxidant capacity, phytochemical composition and in vitro antioxidant and anti-inflammatory activity of C. sativa burrs (CSB) aqueous extract. The spectrophotometric study yielded optimal total phenolic content (TPC) values, along with significant antioxidant and anti-radical properties. The utilization of UPLC-MS-MS techniques for phytochemical investigation resulted in the identification of a total of 56 metabolites, providing confirmation of the presence of phenolic compounds in CSB. In addition, CSB significantly downregulated pro-inflammatory mediators in LPS-stimulated RAW 264.7 macrophage cells without significant cell toxicity.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

This study investigated the presence, distribution, and antimicrobial resistance profiles of extend-ed-spectrum beta-lactamase (ESBL)-producing Enterobacteriaceae in a dairy herd located in Northern Italy. A questionnaire was administered, and the feces of clinically healthy pre-weaned dairy calves, their mothers, and the cows treated for mastitis, waste milk, water, and environmental samples, were collected and inoculated on Chromagar ESBL™ medium. The questionnaire identi-fied several risk factors including administration of waste milk to male calves, lack of routine cleaning of calf feeding and housing equipment, and blanket dry cow therapy. Escherichia coli was identified by MALDI-TOF MS in the feces of 28 of 37 (75.67%) calves, 2 of 3 (66.67%) treated cows, 8 of 14 (57.15%) environmental samples, and the waste milk. Six of 14 (42.85%) environmental samples were also positive for ESBL Acinetobacter baumannii, while all fecal samples were negative. ESBL production was confirmed for all E. coli isolates based on the double disk susceptibility test (DDST), while none were carbapenemase producers. Upon minimal inhibitory concentration (MIC) analysis, all of them showed multiple resistances and were categorized as multi-drug resistant (MDR). This study confirms the widespread presence of MDR, ESBL-E. coli in dairy calves and highlights their diffusion in the farm environment.

Anthropogenic chemicals are fundamental to our standard of living in modern society. Unfortunately, some chemicals are persistent and can enter waste streams and ultimately the environment. Commonly used household products including pharmaceuticals and personal care products are an important source of contaminants. The aim of this study was to develop an “Up-the-pipe Solutions” framework to raise awareness about the presence and potential risks of chemicals found in household products to reduce their levels in waste streams or substitute them with less harmful alternatives. This approach based on The Natural Step framework and the concept of essentiality recognises the importance of engaging the community to raise awareness around the consequences of our daily activities and behavioural patterns that can lead to the release of persistent contaminants in main waste streams from the kitchen and bathroom and green wastes we generate.

The edible portion of Cannabis sativa L. are the seeds. The seeds are generally used for the production of hemp oil, appreciated for the high percentage of α-linolenic acid. The waste obtained after seeds oil extraction, reduced in fine powder, is the subject of this study. Since hemp seeds are considered to be a source of many valuable bioactive compounds, the addition of hemp seed flour to durum wheat for making fortified bread could have an effect on the health of consumers. The aim of this study was to use variable percentages of hemp seed flour for the production of bread, and to determine the fortification impact on chemicals, texture, organoleptic characteristics, crumb color, changes in crumb texture, total polyphenols, free radical scavenging activity and amino acids contents. The rheological and chemical qualities of bread samples, obtained by using a durum wheat cultivar Ciclope fortified with defatted hemp seeds flours, were evaluated. The solid residue left after the extraction of the oil from seeds (generally thrown away as waste or added to feed) was shredded and sieved at 0.530 mm (Hemp 1) or 0.236 mm (Hemp 2). Samples of fortified breads were obtained by substitution of variable percentages of durum wheat flour with the two hemp flours (5%, 7.5%, and 10%). Fortified bread’s total phenolic content was in a range of 0.73±0.017 and 1.73±0.029 mg GAE/g and an-ti-radical scavenging activity was included in the range from 1.17±0.099 and 3.18±0.071mmol TEAC/100g, according to the increasing fortification. Comparison between bread made with Ciclope semolina and hemp flour fortified breads, showed a large increase in amino acid content in fortified samples ones. In particular, bread fortified with 10% Hemp 2 flour highlights a greater content of glutamic acid, tyrosine, proline and essential amino acids such as leucine and isoleucine, compared to the other samples with same percentage of substitution. The amount of hemp seed flour influenced the color of the crumb by increasing the yellow index from 18.24 (100% Ciclope) to 21.33 (bread with Hemp 2 flour at 5%).

Reductive leaching in the Bayer cycle using of iron (2+) allows Al extraction to be significantly increased by magnetization of Al-goethite and Al-hematite. However, the use of expensive iron (2+) salts or iron powder as a source of iron (2+) leads to a significant increase in production costs. In this work, the feasibility of a new method, the reductive leaching of bauxite using an electrolysis process, was investigated. Reduction of iron minerals of boehmitic bauxite in both Bayer solution and purely alkaline solutions were carried out. Experiments were performed using a plate cathode and a bauxite suspension in alkaline solution, as well as using a bulk cathode with a stainless-steel mesh at the bottom of the cell as the current supply. During the electrolysis process, the potential of the cathode relative to the reference electrode was measured as a function of current at different concentrations of solid (100-300 g L–1) and suspension temperatures (95-120 °C). It is shown that the current efficiency using suspension and plate cathode with the predominant deposition of Fe doesn’t exceed 50% even with the addition of magnetite to increase the contact of solid phase with the current supply. With the use of a bulk cathode, the reduction of iron minerals leads predominantly to the formation of magnetite with the efficiency of using electric current more than 80%. As a result of preliminary desilication and electroreduction it is possible to extract more than 97% of Al from bauxite, and to increase the iron content in the bauxite residue to 57-58%.

Red mud (RM) is a residue obtained from the production of alumina. It contains a high concentration of metal oxides and waste concentrated sodium hydroxide solution (pH = 13). To increase the value of RM, an environmentally friendly process of transesterification using waste cooking oil (WCO), MeOH and concentrated sodium hydroxide solution (CSHS) from aluminum production was proposed. Triglycerides of WCO reacted with MeOH at 60 oC to yield mixtures of fatty acid methyl esters (FAMEs) in the presence of 2.03% (w/w) CSHS/WCO using the CSHS (0.204 mol L-1, predetermined by potentiometric titration) from aluminum production by the Bayer process or with the addition of 0.68% (w/w) fabric softener (3% w/w cetyltrimethylammonium chloride in solution) as a phase transfer (PTA) agent. The addition of PTA to the catalyst resulted in a better yield of the products (greater than 98% yield). A simplified mechanism is presented to account for the experimental results.

Nuclear technologies have the potential to play a major role in the transition to a global net-zero society. Their primary advantage is the capability to deliver controllable 24/7 energy on demand. However, as a prerequisite for successful worldwide application, significant innovation will be required to create the nuclear systems of the 21st century, the need of the hour. The pros and cons of nuclear are discussed and analysed at different levels – the societal and public recognition as well as the scientific/engineering and economic level – to assure a demand driven development. Based on the analysis of the different challenges a vision for the nuclear system of the 21st century is synthesised consisting of three pillars – unlimited nuclear energy, zero waste nuclear, and accident free nuclear. These three combined visions are then transformed into dedicated and verifiable missions which are discussed in detail regarding challenges and opportunities. In the following a stepwise approach for the development of such a highly innovative nuclear system is described. Essential steps to assure active risk reduction and the delivery of quick progress are derived as answer to the critique on the currently observed extensive construction time and cost overruns on new nuclear plants. The 4-step process consisting of basic studies, experimental zero power reactor, small scale demonstrator, and industrial demonstrator is described. The 4 steps including sub-steps deliver the pathway to a successful implementation of such a ground breaking new nuclear system. The potential sub-steps are discussed with the view not only onto the scientific development challenges, but also as an approach to reduce the regulatory challenges of a novel nuclear technology.

Malnutrition is one of major factors of bone and cartilage disorders. Pacific cod (Gadus macrocephalus) processing waste is a cheap and highly promising source of bioactive substances, including collagen-derived peptides and amino acids, for bone and cartilage structure stabilization. Addition of these substances to a functional drink is one of the ways to achieve their fast intestinal absorption. Collagen hydrolysate was obtained via enzymatic hydrolysis, ultrafiltration, freeze-drying, and grinding to powder. The lyophilized hydrolysate was a light gray powder with high protein content (>90%), including collagen (about 85% of total protein) and a complete set of essential and non-essential amino acids. The hydrolysate was applicable as a protein food supply or a structure-forming food component due to presence of collagen fiber fragments. An isotonic fitness drink (osmolality 298.1 ± 2.1 mOsm/L) containing the hydrolysate and vitamin C as a cofactor in collagen biosynthesis was prepared. Addition of the hydrolysate did not adversely affect its organoleptic parameters. Production of such functional foods and drinks is one of the beneficial ways of fish processing waste utilization.

The article provides an overview of nanocomposites and microelectronic elements used in space electronics and radiation control systems of nuclear reactors. Only those nanocomposites and microelectronic elements are taken into account that improve their characteristics in radiation fields or remain indifferent when exposed to ionizing radiation. Considering the chemical composition of the materials of these nanocomposites and microelectronic elements, it is analyzed from which radioactive materials (RM) obtained by recycling radioactive waste (RW) such composites and microelectronic parts can be made. Thus, an alternative way of radioactive waste disposal is proposed, when these wastes are used in the form of microelectronic elements designed to operate under conditions of cosmic radiation.

The negative impact of the modern-day lifestyle on the environment is aggravated during the COVID-19 pandemic through the increased use of single-use plastics from food takeaways to medical supplies. Similarly, the closure of food outlets and disrupted supply chains have also resulted in significant food wastage. As the pandemic rages on, the aggravation of increased waste becomes an increasingly urgent problem that threatens the biodiversity, ecosystems, and human health worldwide through pollution. While there are existing methods to deal with the organic and plastic waste, many of the solutions also cause additional problems. Increasingly proposed as a natural solution to man-made unnatural problems, there are insect solutions for dealing with the artificial and organic waste products towards a circular economy, making the use of natural insect solutions commercially sustainable. This review discusses the findings and how some of these insects, particularly the Hermetia illucens, Tenebrio molitor, and Zophobas morio, can play an increasing important role in food and plastics, with a focus on the latter.

Nutrient depletion in Tanzanian sisal production has led to yield decreases over time. We use nutrient mass balances embedded within a life cycle assessment to quantify the extent of nutrient depletion for different production systems, then used circular economy principles to identify potential cosubstrates from within the Tanzanian economy to anaerobically digest with sisal wastes. The biogas produced is then used to generate bioelectricity and the digestate residual can be used as a fertilizer to address the nutrient depletion. If no current beneficial use of the cosubstrate was assumed, then beef manure and marine fish processing waste were the best cosubstrates. If agricultural wastes were assumed to have a current beneficial use as fertilizer, then marine fish processing waste and human urine were the best cosubstrates. The largest reduction in environmental impacts resulted from bioelectricity replacing electricity from fossil fuels in the national electricity grid and improved onsite waste management practices. There is significant potential to revitalize Tanzanian sisal production by applying circular economy principles to sisal waste management and bioenergy production.

The risk of inhalation exposure to elevated concentrations of hydrogen sulfide (H₂S) and ammonia (NH₃) during the agitation of stored swine manure is high. Once or twice a year, farmers agitate manure before pump-out and application to fields. Agitation of the swine manure causes the short-term releases of highly toxic levels of H₂S and NH₃. In our previous pilot-scale studies, the biochar powder had shown significant mitigation of H₂S and NH₃ emissions when surficially applied to manure immediately before agitation. However, fine biochar powder application poses hazards by itself and may not be practical to apply on a farm scale, especially when livestock and workers are present. We hypothesized that applying pelletized biochar to manure surface is just as effective as applying powder to protect farmers and animals from excessive exposure to H₂S and NH₃. This work reports on the lab-scale proof-of-the-concept trials with biochar pellets on the lab-scale. The objective was to compare the biochar pellets and biochar powder on their effectiveness of mitigation on H₂S and NH₃ gases during 3-hour long swine manure agitation. Three scenarios were compared in (n=3) trials (i) control, (ii) 12.5 mm thick surficial application to manure surface of biochar powder, and (iii) an equivalent (by mass) dose of pelletized biochar applied to manure surface. The biochar powder was bound with 35% (wt) water into ~5 × 10 mm (dia × length) pellets. Biochar powder was significantly (p<0.05) more effective than the biochar pellets. Still, pellets reduced total H₂S and NH₃ emissions by ~72% and ~68%, respectively (p=0.001), compared with ~99% by powder (p=0.001). The maximum H₂S & NH₃ concentrations were reduced from 48.1±4.8 ppm & 1,810±850 ppm to 20.8±2.95 ppm & 775±182 ppm by pellets, and to 22.1±16.9 ppm & 40.3±57 ppm by powder, respectively. These reductions are equivalent to reducing the maximum concentrations of H₂S and NH₃ during the 3-h manure agitation by 57% and 57% (pellets) and 54% and 98% (powder), respectively. Treated manure properties hinted at improved nitrogen retention, yet not significant due to high variability. We recommend scaling-up and trials on the farm-scales using biochar pellets to assess the feasibility of application to large manure surfaces and techno-economic evaluation.

Biochar application to the soil can improve soil quality and nutrient leaching loss. Recent studies have reported that surficial application of biochar to stored swine manure can reduce emissions of odorous compounds and reduce the volatilization loss of ammonia. Our working hypothesis was that the biochar-treated manure application to the soil would decrease nutrient leaching from manure and increase plant-available nutrients. The study objectives were to evaluate the impact of biochar-treated swine manure on soil total C, N, and other major and minor nutrients. Three biochars (i) neutral pH red-oak (RO), (ii) highly alkaline autothermal corn (Zea mays) stover (HAP), and (iii) mild acidic Fe-treated autothermal corn stover (HAPE) were incubated with swine manure for a month. The biochar-manure mixture was applied in triplicate to soil columns with application rate determined by the P₂O₅-P content in manure or manure-biochar mixtures after the incubation. The ammonium (NH₄⁺), nitrate (NO₃^-), and reactive P concentrations in soil column leachates were recorded for eight leaching events. Soil properties and plant-available nutrients were compared between treatments and control manure & soil. Manure-(HAP&HAPE) biochar treatments significantly increased soil organic matter (OM) and increased soil total C, N, and improved soil bulk density. Concentrations of KCl-extractable NH₄⁺ and NO₃^- significantly increased in HAPE column leachates during this 4-week study and in the soil after the experiment. A significant reduction in soil Mehlich3 Cu was also observed for the manure-HAPE mixture compared with the control. Overall, the manure-biochar incubation enabled biochar to sorb nutrients from manure, and the subsequent manure-biochar mixture application to soil improved soil quality and plant nutrient availability in comparison to conventional manure application to soil. This proof-of-the-concept study suggests that biochars could be used to solve both environmental and agronomic challenges and further improve the sustainability of animal and crop production agriculture.

HDPE (high-density polyethene) plastic waste is stronger, harder, and more resistant to high temperatures than other plastics. Using it as an additive in a concrete mixture is one solution to reduce this type of waste. We examined how HDPE-type plastics can be used as an additive material in the manufacture of concrete to improve its hardness, tensile strength and compressive strength. Using 156 samples, we aimed to identify the effect of HDPE plastic fibres on concrete of three qualities; B0, f'c10 MPa (low quality), and f'c25 MPa (medium and high quality). We added four compositions (2.5%, 5%, 10% and 20% by weight of cement) of HDPE plastic fibre to each quality of cement, with HDPE plastic fibre sizes of 1 x 1 cm, 0.5 x 2 cm or 0.25 x 4 cm. We found that the addition of 5% HDPE plastic fibre with a 0.5 x 2 cm cross-sectional shape to the f'c10 MPa concrete gives the best result, with increased tensile and compressive strength of the concrete.

The food distribution process is responsible for significant quality loss in perishable products. However, preserving quality is costly and consumes a tremendous amount of energy. To tackle the challenge of minimizing transportation costs and CO2 emissions while also maximizing product freshness, a novel multi-objective model is proposed. The model integrates a vehicle routing problem with temperature, shelf life, and energy consumption prediction models, thereby enhancing its accuracy. Non-dominated sorting genetic algorithm II is adapted to solve the proposed model for the set of Solomon test data. The conflicting nature of these objectives and the sensitivity of the model to shelf life and shipping container temperature settings are analyzed. The results show that optimizing freshness objective degrade the cost and the emission objectives, and the distribution of perishable foods are sensible to the shelf life of the perishable foods and temperature settings inside the container.

Construction and demolition waste (CDW) represents 1/3 of the weight of all-waste produced. Increasing their recycling and reutilization with recycled aggregates (RA) means closing the life cycle of construction materials. Research has been carried out on artificial aggregates from the exclusive crushing of structural concrete waste in selective demolitions (CDWRConc). This study analyses the use of recycled concrete as graded aggregate (GARConc) and in cement soil (CSRConc). The material complies with the requirements as a road base, although due to the low values of resistance to fragmentation these materials are adequate for use in sensitive road systems and other places such as urban roads and car parks. The sensitive road systems are infrastructures in places of great natural wealth and low traffic intensity, with an annual average of heavy vehicle traffic (AADTh) below 50 vhp/d. As soluble salt contents have been detected, additional waterproofing or drainage measures must be adopted to prevent water infiltration into the layers made up of CDWRHorm. Finally, the high initial values of UCS allow the temporary passage of light vehicles over CSRConc after 3 days.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Hyperspectral imaging data holds great potential for various stages of the mining life cycle in active and abandoned mines. The technology, however, has yet to achieve large-scale industrial implementation and acceptance. While hyperspectral satellite im-agery yields high spectral resolution, high signal-to-noise ratio (SNR), and global availability with breakthrough satellite sys-tems like EnMAP, EMIT, and PRISMA, limited spatial resolution poses challenges for mining sectors, which require decimeter- to centimeter-scale spatial resolution for applications such as reconciliation, ore/waste estimates, geotechnical assessments, and en-vironmental monitoring. Hyperspectral imaging from drones (Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the pit/ mine scale, with the capability for frequent, user-defined re-visit times. Collecting data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions offers to detect different minerals and surface alteration patterns, potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we review of applicable instrumentation, software components, and relevant studies deploying hyperspectral imaging in or appropriate to the mining sector, especially for hyperspectral VNIR-SWIR UASs. If directly applicable, draw on previous insights derived from airborne, satellite, and ground-based imaging systems. We also discuss common practices for UAS survey planning and sampling considerations for interpretation.

Peanut hulls (PH) are an edible food waste that is an underutilized food source for human consumption. While edible and palatable, they are mainly diverted to livestock feed or building materials. Here, we describe existing literature on human food valorization of PHs and propose methods to optimize recapturing nutrients (e.g. protein, fiber, polyphenols) lost by treating PHs as waste. Incorporated into common foods, PHs can be processed into functional ingredients to improve nutrient-density and the corresponding positive health outcomes associated with increases in plant foods. PH valorization can also address additional priorities of the UN Sustainable Development Goals using a Food Systems Approach (FSA) including food waste, increasing economic opportunities for farmers, and increasing the availability of healthy shelf-stable foodstuffs to address food security. Recent advances in sustainable food processing technologies can be utilized to safely incorporate peanut hulls into human food streams. We propose future applications that could make meaningful impacts to food availability and the nutritional composition of common foods. While the limited literature on this topic spans several decades, no global operations exist to incorporate peanut hulls and most publications precede the technological ‘green revolution’. The approaches outlined in this review may help bolster commercialization of this underutilized and nutritious food potentially improving opportunities for multiple global stakeholders.

This paper focuses on the highly radioactive, long-lasting nuclear waste produced by the currently operating fission reactors and on the way to deal with the sensitive issue of spent fuel reprocessing. The review includes a short description of the fission process and a detailed analysis of the more hazardous radioisotopes produced either by secondary reactions occurring in the nuclear installations or by decay of the fission fragments. Also outlined are the strategies presently adopted to minimize the harmfulness of the nuclear waste to be disposed and discussed advanced options and possible solutions proposed for the recycling of the used fuel and for the reusing of some technologicaly relevant radioisotopes.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

Global food waste has a huge impact on the environment, as it is a source of greenhouse gas (GHG) emissions and wasted natural resources. Across the world, over 30% of food is lost or wasted each year. Aside from this, food industry, as well, is one of the biggest sources of agro-industrial waste and by-products, which can be valorized and used for different purposes. Such waste is a good source of bioactive organic compounds which can be extracted without al-tering their properties, where deep eutectic solvents (DESs) can serve as green solvents and excel-lent replacement for volatile organic solvents. Isolated compounds can be used in innovative food production, chemical production, cosmetics and other industries. DESs have attracted extraordi-nary attention due to their advantages such as environmental friendliness, availability and easy preparation, easy handling and utilization of non-toxic components for their formation. Due to those properties, they are a greener alternative to classic organic solvents for many processes, in-cluding extractions. In this paper, we review the utilization of deep eutectic solvents as potential green media for the extraction of organic compounds such as polyphenols, carbohydrates, pro-teins, alkaloids from by-products of the food industry and agro-industrial-waste.

To ensure sustainable production and consumption in the agricultural sector, it is necessary to assess the contribution of each element of the nexus in the agricultural production chain. The aim of this study is to make a quantitative and qualitative analysis of the contributions of each element of the energy, water, waste and land nexus to agricultural products. A composite method approach combining aspects based on input-output model, Location Quotient (LQ) as well as competitive position is adopted. A database of nexus elements over a period from 2009 to 2018 is used for Cameroon, with ten regions considered. The results show proportions of around 0.42% energy, 67.88% water withdrawal, 11.91% harvested area, 97.81% waste for agricultural products. The geolocation of harvested areas shows that the largest portion is in the far north (1,373,829 ha) and the smallest in Adamawa (224,038 ha). Maximum production is in the central region (4,334,095 tons) and minimum in the Adamawa region (915,841 tons). The central, littoral and west regions are more representative of agricultural products. The analysis of the competitive position of agricultural products contributes to a better orientation of national strategies for agricultural sustainability according to existing potentials.

This study deals with the computational analysis of the kinetic processes of a microbial electrolysis cell assisted-anaerobic digestion (MEC-AD) treating raw-waste activated sludge (WAS), comparatively with a conventional AD, as well as the effect of the Organic Loading Rate (OLR) on the system’s performance. The aim was to derive a single kinetic and mathematical model for the study of the MEC-AD, using the ADM1 framework, which can be utilized to extract the effect of an applied potential on the kinetics of AD. The experimental data were obtained from the long-term, continuous operation of two identical reactors (an AD and a MEC-AD), which were operated at different OLRs (1.1, 1.7 and 2.9 gCOD/(L*d)). The results showed that the MEC-AD yielded improved biomass yields, substrate consumption kinetics and 1st order disintegration kinetics, with a predominant contribution to disintegration of complex particulates, comparatively with the AD. Moreover, it enabled operation at higher OLRs (achieving the highest divergence from the AD at the OLR of 4.14 gCOD/(L*d)), therefore accelerating sludge treatment, as well as an improved performance at an increased solids retention time (SRT). These findings can serve as a quantitative guide for the effects of the operating parameters on the raw-WAS-fed MEC-AD performance.

Since a large amount of sewage sludge (WSS) has been generated daily, it is necessary to explore effective methods for utilizing WSS. Although a photo-fermentation system sometimes alters the characteristics of microbial functions, there are no attempts to perform the photo-fermentation using WSS which is regularly treated under a dark-fermentation style. In this study, the effect of photo-fermentation (photo-irradiation) on anaerobic digestion using WSS was revealed. Photo-irradiation during the anaerobic digestion of WSS significantly reduced the amount of organic acids and hydrogen sulfide and methane production was also suppressed. However, it was shown that the activity of sulfate-reducing bacteria in WSS under the light treatment increased. Photo-irradiation also stimulated the growth of green-sulfur bacteria and induced anoxygenic photosynthesis, by which the fermented samples turned green linking with the consumption of hydrogen sulfide. Finally, a dark/light switching fermentation was able to reduce only hydrogen sulfide while methane production remained the same.

The fishmeal production industry is essential for providing protein for animal feed in the aquaculture sector. However, the industry faces challenges related to energy consumption and environmental sustainability. This study evaluates the energy efficiency and environmental benefits of waste heat recovery (WHR) technologies in a fishmeal production plant in Vietnam. Data were collected from the plant between 2016 and 2022, and a specific energy consumption (SEC) indicator and a comprehensive methodology were utilized. Implementing an economizer as a WHR technology resulted in a 55.5% decrease in SEC compared to the state before installation. The enhanced energy efficiency also translated to reduced energy consumption per output unit. Moreover, the economizer contributed to annual energy savings of 4,537.57 GJ/year and cost savings of $26,474.49. Additionally, carbon dioxide (CO2) emissions associated with producing one ton of fishmeal decreased by 58.37%. These findings highlight the potential for WHR technologies to improve energy efficiency and reduce the environmental footprint of fishmeal production. The study's results provide valuable insights for practitioners and policymakers in promoting energy efficiency practices and reducing environmental impact in the industry.

High-strength wastewaters from a variety of sources, including the food industry, domestic septage and landfill leachate, are often hauled to municipal wastewater treatment plants (WWTPs) for co-treatment. Due to their high organic loadings, these wastewaters can cause process upsets in both the WWTP’s liquid and solids treatment trains and consume organic treatment capacity, leaving less capacity available to service customers in the catchment area. A novel pre-treatment method, the Waste Activated Sludge-High Rate (WASHR) process, is proposed to optimize the co-treatment of high-strength wastewaters. The WASHR process combines the contact stabilization and sequencing batch reactor processes. It utilizes waste activated sludge from the municipal WWTP as its biomass source, allowing rapid start-up. Bench scale treatment trials of winery wastewater confirm the WASHR process can reduce loadings on the downstream WWTP’s liquid treatment and solids treatment trains. A case study approach is used to confirm the economic viability and environmental sustainability of the WASHR process compared to direct co-treatment using life cycle cost analyses and greenhouse gas emissions estimates.

Red mud (RM) is composed of a waste alkaline solution (pH = 13.3) obtained from the production of alumina. It contains high concentrations of soluble hematite (Fe2O3), goetite (FeOOH), gibisite [Al(OH)3], a boemite (AlOOH), anatase (Tetragonal - TiO2), rutile (Ditetragonal dipyramidal - TiO2), hydrogarnets [Ca3Al2(SiO4)3−x(OH)4x], and perovskite (CaTiO3). It was shown to be an excellent catalytic mixture for biodiesel production. To demonstrate the value of RM, an environmentally friendly process of transesterification in aqueous medium using waste cooking oil (WCO), MeOH and waste alkaline solution (WAS) obtained from aluminum production was proposed. Triglycerides of WCO reacted with MeOH at 60 oC to yield mixtures of fatty acid methyl esters (FAMEs) in the presence of 0.019% (w/w) WAS/WCO using the WAS (0.204 mol L-1, predetermined by potentiometric titration) from aluminum production by the Bayer process. The use of the new catalyst (WAS) resulted in a high yield of the products (greater than 99% yield).

As a result of rapid population growth, an exponentially growing human population, and industrial expansion, it has become increasingly difficult to manage municipal solid wastes throughout the world. Decentralized waste management systems have created difficult situations in developing countries such as Malaysia. Wastes generated in the country, due to various cultural, social, and religious activities, organic and contributing to environmental pollution (air, water, and soil) and human health troubles. A questionnaire survey was participated by 220 construction professionals in Malaysia using structured and semi-structured methods. The framework was assessed using A partial least square structural equation modeling (PLS-SEM) to target sustainable development goals (SDG). Statistical analysis results indicate a significant effect between SCW management, since(r(270)=.687, P&lt;0.001). Improving factors has strong relationship with SCW management, since(r(270)=.723, P&lt;0.001). The mediation results also suggested a significant indirect positive effect of improving factors drivers on SCW management through policy-related factors sinceβ=0.688, t=8.254, P&lt;0.001, 95% CI for β=0.536,0.866. Finally, policy-related factors construct has a strong relationship with SCWM) management, since(r(270)=.811, P&lt;0.001) With the R Square of 0.787 and 0.785. The developed framework can improve construction waste management in the construction industry and enhance construction waste management to achieve global sustainable development goals. The findings show that one of the most critical issues of enhancing profitability is using preventive policies to reduce construction waste. This study could guide construction industry stakeholders in identifying the different waste management features during a building project's construction and design stage

The extraction of grape processing waste (wine pomace) via microwave-hydrodiffusion and gravity (MHG) from three different cultivars grown in Sicily (Syrah, Perricone and Nero d’Avola) rapidly affords aqueous extracts highly concentrated in valued biophenols including flavonoids, anthocyanins and phenolic acids. The method does not employ organic solvent, acid or base and does not require grinding or freeze drying of the wine pomace nor separation of the grape skins from seeds and stem. All the extracts have a pronounced stability as shown by their red-violet color fully retained after storage for more than a year (15 months) in freezer under air. Concentrations of phenolics up to 2000 ppm were detected in the aged extracts of Sicily’s local cultivar Perricone, which also has the highest content of flavonoids. These findings provide a simple and economically viable extraction route to biophenol-rich red extracts that can be used as food colorants as well as to formulate nutraceutical, cosmetic and personal care products starting from an agricultural by-product available in >10 million tonne yearly amount.

As a consequence of intense industrialization in the last few decades, the amount of agro-industrial wastes has increasing, where new forms of valorization are crucial. In this work, 5 residual biomasses from Maranhão (Brazil) were investigted as supports for immobilization of lipase from Thermomyces lanuginosus (TLL). The new biocatalysts BM-TLL (babaçu mesocarp) and RH-TLL (rice husk) showed immobilization efficiencies &gt;98% and hydrolytic activities of 5,331 U.g-1 and 4.608 U. g-1 respectively against 142 U. g-1 by Lipozyme® TL IM. High esterification activities were also found, with 141.4 U.g-1 and 396.4 U.g-1 from BM-TLL and RH-TLL against 113.5 U.g-1 by TL IM. Results of porosimetry, SEM and BET demonstrated BM and RH supports are mesoporous materials with large hydrophobic area, allowing a mixture of hydrophobic adsorption and confinement, resulting in hyperactivation of TLL. These biocatalysts were applied in the production of hexyl laurate, where RH-TLL was able to generate 94% conversion in 4 h. Desorption with Triton X-100 and NaCl confirmed that new biocatalysts were more efficient with 5 times less protein than commercial TL IM. All results demonstrated that residual biomass was able to produce robust and stable biocatalysts containing immobilized TLL with better results than commercial preparations.

The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

This study explores the potential to reach a circular economy for post-consumer recycled polyethylene terephthalate (rPET) packaging and bottles by using it as a distributed recycling for additive manufacturing (DRAM) feedstock. Specifically, rPET is processed using only an open source toolchain with fused particle fabrication (FPF) or fused granular fabrication (FGF) processing. In this study, first the impact of granulation, sifting and heating (and their combination) is quantified on the shape and size distribution of the rPET flakes. Then feeding studies were performed to see if they could be printed through an external feeder or needed to be direct printed with a hopper using two Gigabot X machines, one with extended part cooling and one without. Print settings were optimized based on thermal characterization and for the latter which was shown to print rPET directly from shredded water bottles mechanical testing is performed. The results showed that geometry was important for extended feeding tubes and direct printed using a hopper. Further there is a wide disparity in the physical properties of rPET from water bottles depending on source and the history of the material. Future work is needed to enable water bottles to be used as a widespread DRAM feedstock.

Hydrogen sulfide and ammonia are always a concern in the livestock industries, especially when farmers try to clear their manure storage pits. Agitation of manure can cause dangerously high concentrations of harmful agents such as H₂S and NH₃ to be emitted into the air. Biochar has the ability to sorb these gases. We hypothesized that applying biochar on top of manure can create an effective barrier to protect farmers and animals from exposure to NH₃ and H₂S. In this study, two kinds of biochar were tested, highly alkaline, and porous (HAP, pH 9.2) biochar made from corn stover and red oak biochar (RO, pH 7.5). Two scenarios of (6 mm) 0.25” and (12 mm) 0.5” thick layers of biochar treatments were topically applied to the manure and tested on a pilot-scale setup, simulating a deep pit storage. Each setup experienced 3-min of agitation using a transfer pump, and measurements of the concentrations of NH₃ and H₂S were taken in real-time and measured until the concentration stabilized after the sharp increase in concentration due to agitation. The results were compared with the control in the following 3 situations: 1. The maximum (peak) flux 2. Total emission from the start of agitation until the concentration stabilized, and 3. The total emission during the 3 min of agitation. For NH₃, 0.5” HAP biochar treatment significantly (p<0.05) reduced maximum flux by 63.3%, overall total emission by 70%, and total emissions during the 3-min agitation by 85.2%; 0.25” HAP biochar treatment significantly (p<0.05) reduced maximum flux by 75.7%, overall, total emission by 74.5%, and total emissions during the 3-min agitation by 77.8%. 0.5” RO biochar treatment significantly reduced max by 8.8%, overall total emission by 52.9%, and total emission during 3-min agitation by 56.8%; 0.25” RO biochar treatment significantly reduced max by 61.3%, overall total emission by 86.1%, and total emission during 3-min agitation by 62.7%. For H₂S, 0.5” HAP biochar treatment reduced the max by 42.5% (p=0.125), overall total emission by 17.9% (p=0.290), and significantly reduced the total emission during 3-min agitation by 70.4%; 0.25” HAP treatment reduced max by 60.6% (p=0.058), and significantly reduced overall and 3-min agitation’s total emission by 64.4% and 66.6%, respectively. 0.5” RO biochar treatment reduce the max flux by 23.6% (p=0.145), and significantly reduced overall and 3-min total emission by 39.3% and 62.4%, respectively; 0.25” RO treatment significantly reduced the max flux by 63%, overall total emission by 84.7%, and total emission during 3-min agitation by 67.4%.

The annual construction and demolition waste (CDW) generated from EU construction sector was 850 million tons, which represented 31% of the total waste generation and about 28% of CDW was ceramics (bricks and tiles). In this study, the feasibility of using CDW brick powder as the precursor of alkali activated mortar (AAM) and extruded polystyrene (XPS) as the lightweight aggregates to form lightweight brick powder AAM (LW-BP-AAM) for non-structural applications was investigated. The thermal conductivity of LP-BPAAM was 0.112 W/m·K with density of about 1,135 kg/m³ which was lower than the counterparts with similar density in literature. The acid resistance of LW-BP-AAM is comparable to conventional fly ash based AAM and superior than ordinary Portland cement. From the scanning electron microscopy with energy dispersive X-ray spectroscopy, there was no severe damage on the surface of LW-BP-AAM but aluminate was removed from the matrix which was further verified in Fourier transform infrared spectroscopy. The mass and strength loss of LP-BP-AAM was 1.5% and 33%, respectively. Although the compressive strength of the LP-BP-AAM was low (about 1.8 MPa), it can be improved by optimising the particle size of the XPS aggregates.