Two austenitic stainless steel (ASS) plates, 304L and 316L, were cold-rolled (304R and 316R) with a 10 % reduction in thickness then subjected to laser welding. Cold-rolling caused a slight surface hardening and introduced residual tensile stress into the ASS plates. The susceptibility to stress corrosion cracking (SCC) of the welds (304RW and 316RW) was determined using the U-bend test pieces in a salt spray. To highlight the stress concentration at the weld’s fusion boundary (FB), the top weld reinforcement was not ground off before bending. Moreover, micro-shot peening (MSP) was performed to mitigate the SCC of the welds by imposing high residual compressive stress and forming a fine-grained structure. Cold-rolling increased the susceptibility of the 304R specimen to pitting corrosion (PTC) and intergranular (IG) microcracking. Moreover, PTC and SCC were found more often at the FBs of the 304RW. The corrosion pits of the peened 304RW (304RWSP) were finer but greater in amount than the un-peened one. The results also indicated that the 316L ASS welds with MSP was resistant to the incidence of PTC and SCC in a salt spray. The better reliability and longer service life of dry storage canister could be achieved by using 316L ASS for construction and application of MSP on it.

The aim of this study was to investigate the effect of laser irradiation to computer-aided de-sign/computer-aided fabrication (CAD/CAM) resin blocks coated with a silane coupling agent on the bond strength between the resin blocks and composite resin. The CAD/CAM resin blocks used in this study were Cerasmart 300 (GC) and Vita Enamic (Vita); they were cut into plates and then subjected to a series of treatments. After processing with a silane coupling agent, treatment with a semiconductor laser was performed at 3.0, 5.0, and 7.0 W, followed by the bonding procedures. The control group included those exposed to silane and bonded without laser application. After bonding, a mold with a simulated cavity was formed on the specimen and filled with flowable composite resin, and they were stored for 24 h or stressed by thermal cycling for subsequent testing that assessed the shear bond strength (n = 10). The results revealed that the bond strength was significantly enhanced by laser irradiation after applying a silane coupling agent, whereas significant effect was not detected between the materials. Particularly, 7 W laser irradiation had a significant effect on the bond strength between the composite resin and Cerasmart block after thermal cycling.

The development of the additive manufacturing (AM) technology proffers challenging requirements for forming accuracy and efficiency. In this paper, a hybrid additive manufacturing technology combining fusion-based selective laser melting (SLM) and solid-state cold spraying (CS) was proposed in order to enable the fast production of near-net-shape metal parts. The idea is to fabricate a bulk deposit with a rough contour first via “fast” CS process and then add fine structures and complex features through “slow” SLM. The experimental results show that it is feasible to deposit SLM part onto CS part with good interfacial bonding. However, the CS parts must be subject to heat treatment to improve their cohesion strength before being sending for SLM processing. Otherwise, the high tensile residual stress generated during SLM process will cause fracture and cracks in the CS part. After heat treatment, pure copper deposited by CS undergoes grain growth and recrystallization, resulting in improved cohesive strength and release of the residual stress in the CS parts is released. The tensile test on the SLM/CS interfacial region indicates that the bonding strength increased by 38% from 45±7 MPa to 62±1 MPa after the CS part is subject to heat treatment, and the SLM/CS interfacial bonding strength is higher than the CS parts. This study demonstrates that the proposed hybrid AM process is feasible and promising for manufacturing free-standing SLM-CS components.

In interceptive treatments in which impacted teeth (incisor or first permanent molar) should be included into the dental arch, the main clinical problem is the provision of an anchorage area and a suitable appliance. The use of laser sintered metal orthodontic grids, designed and printed digitally, has expanded the boundaries of orthodontic treatment, especially in its interceptive phase. Our aim is to describe a digital model for providing anchorage during orthodontic-surgical traction of impacted teeth in the mixed dentition period. We present the treatment of three clinical cases with digitally projected and printed metal grids used for anchorage. In the described clinical cases, individually designed anchorage systems were used. They were created through design software and after that the metal grids were printed. The devices are placed in the oral area and don’t disturb the aesthetics of the patient in any way. The advantages of individual designed metal support grids allow to accommodate the features of relief of the hard palate and alveolar bone. This makes the grids comfortable for the patient and rigid enough to perform orthodontic tractions at the same time. The printed additional grids are applicable in mixed dentition and in complicated clinical cases in permanent dentition. Their individuality allows segmental treatments or treatments in cases requiring additional anchorage further from the active force.

Both drones and laser scanners digitally take the as-built context of an object into the computer and the data taken is transmitted to a Building Information Modeling (BIM) world to create ac-curate 3D models. Although the laser scanner is the leading method of the Scan-to-BIM proce-dure, many professionals indicate drawbacks of the technology and point out the drone is an al-ternative that can improve the shortcomings, leading to the UAV-to-BIM process. Korean con-struction industry plans to implement the drone technology for scrutinizing as-built construc-tion quality by 2025. However, the drone is not popular in the construction projects. Korean universities where Construction Engineering and Management program have been implement-ed are requested to develop a drone curriculum for construction professionals. Since the majori-ty of the professionals are not familiar with drone operation, in order for the schools to be suc-cessful in developing the curriculum, it is very necessary to perform a preliminary experimental study for identifying the essential education contents that are appropriate to drone beginners. The main objective of this paper is to perform the study for the drone beginners and recognize the recommendations and the framework of drone curriculum that will be beneficial for the schools to develop a comprehensive curriculum later on.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

So far, poly(L-lactic acid), PLLA, nanosheets proved to be promising for wound healing. Such biodegradable materials are easy-to-prepare, bio-friendly, cost-effective, simple to apply and were shown to protect burn wounds and facilitate their healing. At the same time, certain metal ions are known to be essential for wound healing, which is why this study was motivated by the idea of incorporating PLLA nanosheets with Zn2+ ion containing nanoparticles. Upon being applied on wound, such polymer nanosheets should release Zn2+ ions, which is expected to improve wound healing. The work thus focused on preparing PLLA nanosheets embedded with several kinds of Zn-containing nanoparticles, their characterization and ion-release behavior. ZnCl2 and ZnO nanoparticles were chosen as model particles with different solubility in water, both types showing similar ion release dynamics in liquid medium with pH around 7.4.

Fluorescence microscopy is an important tool for disease diagnosis, often requiring costly optical components, such as fluorescence filter cubes and high-power light sources. Due to its high cost, conventional fluorescence microscopy cannot be fully exploited in low-income settings. Smartphone-based fluorescence microscopy becomes an interesting low-cost alternative, but raises challenges in the optical system. We present the development of a low-cost inverted laser fluorescence microscope, that uses a smartphone to visualize the fluorescence image of biological samples. Our fluorescence microscope uses a laser-based simplified optical filter system, that provides analog optical filtering capabilities of a fluorescence filter cube. Firstly, we validated our inverted optical filtering by visualizing microbeads labeled with three different fluorescent compounds or fluorophores, commonly used for disease diagnosis. Secondly, we validated the disease diagnosis capabilities, by comparing the results of our device with those of a commercial fluorescence microscope. We successfully detected and visualized Trypanosoma cruzi parasites, responsible of the Chagas infectious disease, and the presence of Antineutrophil cytoplasmic antibodies of the ANCA non-communicable autoimmune disease. The samples were labeled with the fluorescein isothiocyanate (FITC) fluorophore, one of the most commonly used for disease diagnosis. Our device provides a 400 X magnification and is at least two orders magnitude cheaper than conventional commercial fluorescence microscopes.

For the first time the gain switching properties of an InAs-InP (113)B quantum dot laser are examined theoretically in detail to generate shorter pulses with the application of a Gaussian pulse beam to the laser excited state. The multi population rate equations considering nonlinear gain are solved by the Runge –Kutta method. The numerical results demonstrated that as the homogeneous and the inhomogeneous broadening increase, the differential gain, the gain compression factor and the threshold current of excited state decrease, while threshold current of ground state increases. It was also observed that the contribution of the excited state to gain-switched output pulses depends on not only the value of the inhomogeneous broadening but also the magnitude of the applied current. Finally it was shown that without an optical beam, output pulse has long pulse width due to ground state emission, whereas with an optical beam, narrow pulses having high peak power owing to the excited state emission are generated even though at low currents.

The orthodontic treatment brings numerous benefits and, in most cases, the benefits outweigh the possible disadvantages. Root resorption (RR) is a common adverse phenomenon associated with orthodontic treatment. This study evaluates the role of low-level laser emission / Photobiomodu-lation (LE/P) in quantitative measurements of root resorption (QRR). The application of LE/P was done after each orthodontic activation with 4 types of treatment intervention (TI) on the RR after fixed orthodontic treatment (FOT) of the upper arch with ectopic eye tooth/teeth [EET]. 32 Orthodontic patients scheduled for FOT were selected and assigned to the 4 groups. These were LE/P+Self ligating bracket (SLB), LE/P+Conventional bracket (CB), Non-Photobiomodulation (non-LE/P)+SLB, and non-LE/P+CB. Standard management stages of FOT were followed in the maxilla. Each patient received a single application of LE/P labially/buccally and palatally, a total of 5 different points during each activation or appointment. The main outcome measure was QRR in maxillary anteriors before and after FOT assessed via cone-beam computed tomography (CBCT) using 3D OnDemand software. Insignificant QRR was found between before and after FOT in SLB, CLB, and LE/P, non-LE/P groups (p > 0.05). QRR in the SLB vs CB and LE/P vs non-LE/P group was significantly different in 11, 13, and 23 (p < 0.05). QRR in the LE/P+SLB group (p < 0.05) was significantly different in 11, 13, and 23 than that in the other groups. The most severe QRR was found on the 13 (0.88 ± 0.28mm and 0.87±0.27mm) and 23 (1.19 ± 0.14 mm and 1.16±0.13mm) in the CB and non-LE/P group (p < 0.001). LE/P+SLB showed highly significant superior outcome (p < 0.001) in relation to non-LE/P+CB, the QRR of 23 were 0.813± 0.114mm and 1.156± 0.166mm respectively. Significantly higher amount of QRR found in EET patients after FOT treated with the CB, non-LE/P, and non-LE/P+CB system and warrants further investigation to explore potential specific causes.

In the recent years, Cannabis and hemp-based products have become increasingly popular for various applications ranging from recreational use, edibles, beverages to health care products and medicines. The rapid detection and differentiation of phytocannabinoids is, therefore, essential to assess the potency, therapeutic and nutritional values of cannabis cultivars. Here, we implemented the SpiderMass technology for the in vivo detection of cannabidiol acid (CBDA) and tetrahydrocannabinol acid (THCA) and other endogenous organic plant compounds to access distribution gradients within the plants and differentiate cultivars. The SpiderMass system is composed of an IR- laser handheld microsampling probe connected to the mass spectrometer through a transfer tube. The analysis was performed in situ on different plant organs from freshly cultivated Cannabis plants in only a few seconds. SpiderMass analysis easily discriminated the two acid phytocannabinoid isomers by MS/MS and the built statistical models differentiated between four Cannabis cultivars. Different abundancies of acid phytocannabinoids were also found along the plant as well as between different cultivars. All together, these results introduce the direct analysis by SpiderMass as a compelling analytical alternative for forensic and hemp industrial analysis.

Laser shock peening is a process which can reduce stress corrosion cracking and improve fatigue life by forming compressive residual stress on the surface of the material. In a computational FE simulation of laser shock peening, during applying the pressure load generated by the laser pulse to the surface of simulation geometry, the peening is simulated by explicit analysis and then convert to implicit analysis to dissipate the dynamic energy remaining in the geometry. In this study, static damping is applied to dissipate residual dynamic energy without converting it into an implicit analysis. The compressive residual stress distribution is compared between the simulation results for the stainless steel 304 material and the same material subjected to actual laser shock peening. The laser shock peening parameters were 4.2J laser pulse energy, 50% overlap of 3mm diameter of the laser beam and water as a confinement layer. As a result, the compressive residual stress from the surface to the depth direction is similar to both the simulation and the experimental result measured by the hole drilling method.

Manual measurement of rock discontinuities is time-consuming and subjective according to the experience of the surveyor. This work proposes a three-dimensional laser scanning-based method for the semi-automatic identification of rock discontinuities. Multisite cloud scanning is performed with real-time kinematic (RTK)-assisted orientation to estimate the rock fracturing degree; then, discontinuity orientations are extracted with the man–machine interactive method or automatic method. The proposed method was applied to actual examples to illustrate its accuracy at identifying rock discontinuities. The sensitivity of the identification accuracy to different parameters was investigated.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

Ti6Al4V samples obtained by selective laser melting were subjected to acid treatment, chemical oxidation in hydrogen peroxide solution and subsequent thermochemical treatment. The effect of temperature and time of acid etching of Ti6Al4V samples on surface roughness, morphology, topography and chemical and phase composition after the thermochemical treatment was studied. The surfaces were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and contact profilometry. Pore and protrusion sizes were measured. Acid etching modified the elemental composition and surface roughness of the alloy. Temperature had a greater influence on the morphology, topography and surface roughness of samples than time. Increases in roughness values were observed when applying successive chemical oxidation and thermochemical treatment compared to the values observed on surfaces with acid etching. After the thermochemical treatment, the samples with acid etching at a temperature of 80 °C showed a multiscale topography. In addition, a network-shaped structure was obtained on all surfaces, both on their protrusions and pores previously formed during the acid etching.

The urgent need to improve performance in the construction industry has led to the adoption of many innovative technologies. 3D laser scanners are amongst the leading technologies being used to capture and process assets or construction project data for use in various applications. Due to its nascent nature, many questions are still unanswered about 3D laser scanning, which in turn contribute to the slow adaptation of the technology. Some of these include the role of 3D laser scanners in capturing and processing raw construction project data. How accurate is the 3D laser scanner or point cloud data? How does laser scanning fit with other wider emerging technologies such as Building Information Modelling (BIM)? This study adopts a proof-of-concept approach, which in addition to answering the afore-mentioned questions, illustrates the application of the technology in practice. The study finds that the quality of the data, commonly referred to as point cloud data is still a major issue as it depends on the distance between the target object and 3D laser scanner’s station. Additionally, the quality of the data is still very dependent on data file sizes and the computational power of the processing machine. Lastly, the connection between laser scanning and BIM approaches is still weak as what can be done with a point cloud data model in a BIM environment is still very limited. The aforementioned findings reinforce existing views on the use of 3D laser scanners in capturing and processing construction project data.

This study evaluates whether a combination of photodiode sensor measurements, taken during laser powder bed fusion (L-PBF) builds, can be used to predict the resulting build quality via a purely data-based approach. We analyse the relationship between build density and features that are extracted from sensor data collected from three different photodiodes. The study uses a Singular Value Decomposition to extract lower-dimensional features from photodiode measurements, which are then fed into machine learning algorithms. Several unsupervised learning methods are then employed to classify low density (< 99% part density) and high density (≥ 99% part density) specimens. Subsequently, a supervised learning method (Gaussian Process regression) is used to directly predict build density. Using the unsupervised clustering approaches, applied to features extracted from both photodiode sensor data as well as observations relating to the energy transferred to the material, build density was predicted with up to 93.54% accuracy. With regard to the supervised regression approach, a Gaussian Process algorithm was capable of predicting the build density with a RMS error of 3.65%. The study shows, therefore, that there is potential for machine learning algorithms to predict indicators of L-PBF build quality from photodiode build-measurements. Moreover, the work herein describes approaches that are predominantly probabilistic, thus facilitating uncertainty quantification in machine-learnt predictions of L-PBF build quality.

Terrestrial laser scanning (TLS) provides detailed three-dimensional representation of the surrounding forest structure. However, due to close-range hemispherical scanning geometry, the ability of TLS technique to comprehensively characterize all trees and especially the upper parts of forest canopy is often limited. In this study, we investigated how much forest characterization capacity can be improved in managed Scots pine (Pinus sylvestris L.) stands if TLS point cloud is complemented with a photogrammetric point cloud acquired from above the canopy using unmanned aerial vehicle (UAV). In this multisensorial (TLS+UAV) close-range sensing approach, the used UAV point cloud data was considered feasible especially in characterizing the vertical forest structure and improvements were obtained in estimation accuracy of tree height as well as plot-level basal-area weighted mean height (H_g) and mean stem volume (V_mean). Most notably the root mean square error (RMSE) in H_g improved from 0.88 m to 0.58 m and the bias improved from -0.75 m to -0.45 m with the multisensorial close-range sensing approach. However, in managed Scots pine stands the mere TLS captured also the upper parts of the forest canopy rather well. Both approaches were capable of deriving stem number, basal area, V_mean, H_g and basal area-weighted mean diameter with a relative RMSE less than 5.5% for all of the sample plots. Although the multisensorial close-range sensing approach mainly enhanced characterization of forest vertical structure in single-species, single-layer forest conditions, representation of more complex forest structures may benefit more from point clouds collected with sensors of different measurement geometries.

High-frequency near-infrared diode laser provides high peak output, low heat accumulation, and efficient biostimulation. Although these characteristics are considered suitable for osteoarthritis (OA) treatment, the effect of high-frequency near-infrared diode laser in in vitro or in vivo OA models has not yet been reported. Therefore, we aimed to assess the biological effects of high-frequency near-infrared diode laser irradiation on IL-1β-induced chondrocyte inflammation in an in vitro OA model. Normal Human Articular Chondrocyte-Knee (NHAC-Kn) cells were stimulated with human recombinant IL-1β and irradiated with high-frequency near-infrared diode laser (910 nm, 4 or 8 J/cm2). The mRNA and protein expression of relevant inflammation- and cartilage destruction-related proteins was analyzed. IL-1β treatment significantly increased the mRNA levels of IL-1β, IL-6, TNF-α, MMP-1, MMP-3, and MMP-13. High-frequency near-infrared diode laser irradiation significantly reduced the IL-1β-induced expression of IL-1β, IL-6, TNF-α, MMP-1, and MMP-3. Similarly, high-frequency near-infrared diode laser irradiation decreased the IL-1β-induced increase in protein expression and secreted levels of MMP-1 and MMP-3. These results highlight the therapeutic potential of high-frequency near-infrared diode laser in OA.

In this paper we show how to efficiently implement parallel discrete simulations on Multi-Core and GPU architectures through a real example of application: a cellular automata model of laser dynamics. We describe the techniques employed to build and optimize the implementations using OpenMP and CUDA frameworks. We have evaluated the performance on two different hardware platforms that represent different target market segments: high-end platforms for scientific computing, using an Intel Xeon Platinum 8259CL server with48cores and also an NVIDIA Tesla6V100 GPU, both running on Amazon Web Server (AWS) Cloud, and on a consumer-oriented platform, using an Intel Core i9 9900k CPU and an NVIDIA GeForce GTX 1050 TI GPU. Performance results are compared and analysed in detail. We show that excellent performance and scalability can be obtained in both platforms, and we extract some important issues that imply a performance degradation for them. We also found that current Multi-Core CPUs with large core numbers can bring a performance very near to that of GPUs, even similar in some cases.

Knowledge of a lasers beam’s profile throughout a laser system and experiment can help immensely in diagnosing laser problems and assisting in beam alignment and focusing at a sample. Obtaining such profiles is a trivial task in the ultraviolet-visible wavelength range but more challenging with near-infrared to infrared beams. Scientific grade bolometer arrays, suitable for such a task, do exist but are extremely costly, relatively large and have a large pixel size, of the order of 80 μm, which is adequate for profiling larger beams but poses an issue when trying to profile sub 100 μm beams for example at a focal point. This communication identifies a micro-bolometer array for near- to mid-infrared laser beam profiling, which is extremely low cost. In addition, the device is very compact, enabling use in confined spaces, and has a small, 12 μm, pixel size permitting the profiling of focused laser beams. The best scientific grade device identified has a pixel size of 17 μm. This device is a powerful tool for infrared laser spectroscopists, reducing the time required to measure the spot size of beams and to achieve spatial overlap of multiple infrared beams as used in two-dimensional infrared spectroscopy, saving many hours of setup time. The use of the bolometer array as a spectrographic detector and probe of long-term beam drifts is also demonstrated.

Temperature field is an essential attribute of metal additive manufacturing in view of its bearings on the prediction, control, and optimization of residual stress, part distortion, fatigue, balling effect, etc. This work provides an analytical physics-based approach to investigate the effect of scan strategy parameters including time delay between two irradiations and hatching space on thermal material properties and melt pool geometry. This approach is performed through the analysis of the distribution of material properties and temperature profile in three-dimensional space. The moving point heat source approach is used to predict the temperature field. To predict the temperature field during the additive manufacturing process some important phenomena are considered. 1) Due to the high magnitude of temperature in the presence of the laser, the temperature gradient is usually high which has a crucial influence on thermal material properties. Consequently, the thermal material properties of stainless steel grade 316L are considered to be temperature-dependent. 2) Due to the repeated heating and cooling, part usually undergoes several melting and solidification cycles. This physical phenomenon is considered by modifying the heat capacity using the latent heat of melting. 3) The multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the successive layers has an impact on heat transfer mechanisms. 4) Effect of heat affected zone on thermal material properties is considered by the superposition of material properties in regions where the temperature fields of two consecutive irradiations have an overlap since the consecutive irradiations change the behavior of the material properties. The goals are to 1) investigate the effects of temperature-sensitive material properties and constant material properties on the temperature field. 2) Study the behavior of thermal material properties under different scan strategies. 3) Study the importance of considering the effect of heat affected zone on thermal material through the prediction of melt pool geometry. 4) Investigate the effect of hatching space on melt pool geometry. This work is purely employed physics-based analytical models to predict the behavior of material properties and temperature field under different process conditions, and no finite element modeling is used.

Molecular overtone transitions provide optical frequency transitions sensitive to variation in the proton-to-electron mass ratio (μ = m_p/m_e). However, robust molecular state preparation presents a challenge critical for achieving high precision. Here, we characterize infrared and optical-frequency broadband laser cooling schemes for TeH⁺, a species with multiple electronic transitions amenable to sustained laser control. Using rate equations to simulate laser cooling population dynamics, we estimate the fractional sensitivity to μ attainable using TeH⁺. We find that laser cooling of TeH⁺ can lead to significant improvements on current μ variation limits.

We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

In this study we fabricate gold nanocomposites and model their optical properties. The nanocomposites are either homogeneous films or gratings containing gold nanoparticles embedded in a polymer matrix. The samples are fabricated using a recently developed technique making use of laser interferometry. The gratings present original plasmon-enhanced diffraction properties. In this work, we develop a new approach to model the optical properties of our composites. We combine the extended Maxwell-Garnett model of effective media with the Rigorous Coupled Wave Analysis (RCWA) method and compute both the absorption spectra and the diffraction efficiency spectra of the gratings. We show that such a semi-analytical approach allows us to reproduce the original plasmonic features of the composites and can give us entails about their inner structure. Such approach could be a simple and efficient tool to study complex micro-structured system based on plasmonic components, such as metamaterials.

In thermal power plants equipped with air-cooled condensers, axial cooling fans operate under the influence of ambient flow fields. Under inlet cross-flow conditions, the resultant asymmetric flow field is known to introduce additional harmonic forces to the fan blades. This effect has previously been studied only numerically or using blade mounted strain gauges. For this study, Laser Scanning Vibrometry was used to assess fan blade vibration under inlet cross-flow conditions in an adapted fan test rig inside a wind tunnel test section. Two co-rotating laser beams scanned a low pressure axial fan, resulting in spectral, phase resolved surface vibration patterns of the fan blades. Two distinct operating points were examined, with and without inlet cross-flow influence. While almost identical fan vibration patterns were found for both reference operating points, overall blade vibration increased by 100% at low fan flow rate due to cross-flow, and by 20% at high fan flow rate. While numerically predicted natural frequency modes could be confirmed from experimental data as minor peaks in the vibration amplitude spectrum, they were not excited significantly by cross-flow. Instead, primarily higher rotation rate harmonics were amplified, i.a. a synchronous blade tip flapping was strongly excited at the blade pass frequency.

Recent advancements in vascular organoid (VO) and vessel-on-chip (VoC) technologies have revolutionized our approach to studying cardiovascular diseases (CVDs), offering unprecedented insights through more physiologically relevant models. VOs generated from human pluripotent stem cells exhibit remarkable self-organization capabilities, forming complex three-dimensional structures that closely mimic human blood vessel architecture and function, while VoCs engineered with groundbreaking microfluidic systems that meticulously recreate the physical and functional attributes of blood vessels. These innovative constructs serve as powerful tools for investigating vascular development, disease progression, and therapeutic efficacy. By enabling the creation of patient-specific VOs and VoCs, they pave the way for personalized medicine approaches, allowing researchers to delve into genetic variations, intricate cellular interactions, and dynamic processes with exceptional resolution. The synergy between VOs and VoCs with cutting-edge technologies such as single-cell sequencing and high-resolution imaging has further amplified their potential, unveiling novel mechanisms underlying CVDs and identifying promising therapeutic targets. Herein, we summarize different types of VOs and VoCs and present an extensive overview on the generation and applications of VOs and VoCs in CVDs. We will also highlight clinical and translational challenges and future perspectives around VOs and VoCs.

This study aims to demonstrate the possibility of incorporating a natural antioxidant biomolecule, into polymeric porous scaffolds. To this end, Poly-L-Lactic Acid (PLLA) scaffolds were produced using the Thermally Induced Phase Separation (TIPS) technique and additivated with different amounts of Rosmarinic Acid (RA). The scaffolds, with a diameter of 4 mm and a thickness of 2 mm, were characterized with a multi-analytical approach. Specifically, Scanning Electron Mi-croscopy analyses demonstrated the presence of an interconnected porous network, character-ized by a layer of RA at the level of the pore’s surfaces. Moreover, the presence of RA biomole-cules increased the hydrophilic nature of the sample, as evidenced by the decrease in contact angle with water from 128° to 76°. This approach is cost-effective, and it could be customized with different biomolecules, offering the possibility of producing porous polymeric structures con-taining antioxidant molecules. These scaffolds meet the requirements of tissue engineering and could be offered a potential solution to reduce inflammation associated with scaffold implantation thus improving tissue regeneration.

Globally, habitat fragmentation has increased the proximity between wildlife, humans, and emerging predators such as free-ranging dogs. In these fragmented landscapes, encounters between primates and dogs are escalating, with primates often falling victim to dog attacks while navigating patchy landscapes and fragmented forests. We aim to investigate how these primates deal with the simultaneous threats posed by humans and predators, specifically focusing on the adaptive strategies of Central Himalayan Langur (CHL) in the landscape of fear. To address this, we conducted a behavioral study on the CHL in an agro-forest landscape, studying them for a total of 3912 hours over two consecutive years. Our results indicate that, compared to their most common resting behavior, CHL allocate more time to feeding and locomotion, and less time to socializing in the presence of humans and predatory dogs. Additionally, they exhibit increased feeding and locomotion and reduced social behavior in agro-forest or open habitats. These behavioral patterns reflect adaptive responses to the landscape of fear, where the presence of predators significantly influences their behavior and resource utilization. This study suggests measures to promote coexistence between humans and wildlife through the integration of effective management strategies that incorporate both ecological and social dimensions of human-wildlife interactions.

To maintain an optimal body content of phosphorus throughout postnatal life, variable phosphate absorption from food must be finely matched with urinary excretion. This amazing feat is accomplished through synchronised phosphate transport by myriads of ciliated cells lining the renal proximal tubules. These respond in real time to changes in the phosphate and composition of the renal filtrate, and to hormonal instructions. How they do this has stimulated decades of research. New analytical techniques, coupled with incredible advances in computer technology, have opened new avenues for investigation at a sub-cellular level. There has been a surge of research into different aspects of the process. These have verified long held beliefs and are also dramatically extending our vision of the intense, integrated, intracellular activity which mediates phosphate absorption. Already, some have indicated new approaches for pharmacological intervention to regulate phosphate in common conditions, including chronic renal failure and osteoporosis, as well as rare inherited biochemical disorders. It is a rapidly evolving field. The aim here is to provide an overview of our current knowledge, to show where it is leading, and where there are uncertainties. Hopefully this will raise questions and stimulate new ideas for further research.

Wild-type p53 cancer therapy-induced senescent cells frequently engulf and degrade neighboring ones inside a massive vacuole in their cytoplasm. After clearance of the internalized cell, the vacuole persists, seemingly empty, for several hours. Despite large vacuoles being associated with cell death, this process is known to confer a survival advantage to cancer engulfing cells, leading to therapy resistance and tumor relapse. Previous attempts to resolve the vacuolar structure and visualize their content using dyes were unsatisfying for lack of known targets and ineffective dye penetration and/or retain. Here, we overcame this problem by applying optical diffraction tomography and Raman spectroscopy to MCF7 doxorubicin-induced engulfing cells. We demonstrated a real ability of cell tomography and Raman to phenotype complex microstructures, such as cell-in-cells and vacuoles, and detect chemical species in extremely low concentrations within live cells in a completely label-free fashion. We show that vacuoles had a density indistinguishable to the medium, but were not empty, instead contained diluted cell-derived macromolecules, and we could discern vacuoles from medium and cells using their Raman fingerprint. Our approach is useful for the non-invasive investigation of senescent engulfing (and other peculiar) cells in unperturbed conditions, crucial for a better understanding of complex biological processes.

Adult stem cells (ASCs) can be cultured with difficulty from most tissues, often requiring chemical or transgenic modification to achieve adequate quantities. We show here that mouse primary fibroblasts grown in suspension change from the elongated and flattened morphology observed under standard adherent culture conditions generating rounded cells with large nuclei and scant cytoplasm expressing the mesenchymal stem cell (MSC) marker (Sca1; Ly6A) within 24hrs. Based on this initial observation, we describe here a suspension culture method that, irrespective of the lineage used, mouse fibroblast, primary human somatic cells (fibroblasts, hepatocytes and keratinocytes), is capable of generating a high yield of cells in spheroid form which display expression of ASCs surface markers, circumventing the anoikis which often occurs at this stage. Moreover, mouse fibroblasts-derived spheroids can be differentiated into adipogenic and osteogenic lineages. Analysis of single cell RNA sequence data identified 8 distinct cell clusters with one in particular comprising approximately 10% of the cells showing high levels of proliferative capacity expressing high levels of genes related to MSCs and self-renewal as well as extracellular matrix (ECM). We believe the rapid, high-yield generation of proliferative, multi-potent ASC-like cells by the process we term suspension-induced stem cell transition (SIST) could have significant implications for regenerative medicine.

Sepsis is a life-threatening organ dysfunction caused by a dysregulated host response to infection, with septic cardiomyopathy being a common and severe complication. Despite its significant clinical impact, the molecular mechanisms underlying sepsis-induced cardiomyopathy (SICM) remain incompletely understood. In this study, we performed a comparative analysis of whole transcriptome profiles in two widely used mouse models of septic cardiomyopathy, the cecal ligation and puncture (CLP) model and the lipopolysaccharide (LPS) model. Our aim was to identify key genes and pathways involved in the development of septic cardiomyopathy and to evaluate the similarities and differences between the two models. Our findings suggested that 1) both methods can induce septic heart dysfunction within 24 hours; 2) distinct whole transcriptome expression profiles are revealed; 3) potentially different pathways are involved in causing heart failure in sepsis. The comprehensive comparison provides valuable insights into the molecular basis of septic cardiomyopathy and contributes to the ongoing search for effective treatment strategies, triggered by different factors for SICM.

Despite extensive research, the links between the accumulation of glycosaminoglycans (GAGs) and the clinical features seen in patients suffering from various forms of Mucopolysaccharidoses (MPSs) have yet to be further elucidated. This is particularly true for the neuropathology of these disorders, even though the neurological symptoms are currently incurable, even in the cases where a dis-ease-specific therapeutic approach does exist. One of the best ways to get insights on the molecular mechanisms driving that pathogenesis is the analysis of patient-derived cells. Yet, not every pa-tient-derived cell holds potential to recapitulate relevant disease features. For the neurodegenerative forms of these diseases in particular, it is challenging to grow neuronal cultures that accurately represent them because of the obvious inability to access live neurons. This scenario changed sig-nificantly since Yamanaka et al. published their protocol for induction of pluripotent stem cells (SC) from adult human fibroblasts. From then on, a series of differentiation protocols to generate neurons from induced pluripotent stem cells (iPSC) was developed and extensively used for disease mod-eling. Currently, human iPSC and iPSC-derived cell models have been generated for several MPS and numerous lessons were learnt from their analysis. Here we review most of those studies, not only listing the currently available MPS iPSC lines and their derived models, but also summarizing how they were generated and the major information different groups have gathered from their analysis. Finally, and taking into account that iPSC generation is a laborious/expensive protocol that holds significant limitations, we also comment on a tempting alternative to establish MPS pa-tient-derived neuronal cells in a much more expedite way by taking advantage of the existence of a population of multipotent SC in human dental pulp, to establish mixed neuronal and glial cultures.

Contrast-induced acute kidney injury (CI-AKI) is a serious complication after angiographic examinations in cardiology. Diagnosis may be delayed based on standard serum creatinine, and subclinical forms of kidney damage may not be detected at all. In our study we investigate the clinical use in these directions of a “damage” type biomarker - Neutrophil Gelatinase-Associated Lipocalin (NGAL). Among patients with a high-risk profile undergoing scheduled coronary angiography and/or angioplasty, plasmsa NGAL was determined at baseline, at 4 and 24 hours after contrast administration. In the CI-AKI group, NGAL increased significantly at the 4th hour (132.33±72.83 ng/ml versus 111.48±65.06 ng/ml, p=0.006) and at the 24th hour (212 .93±276.61 ng/ml, p=0.008). In patients with subclinical CI-AKI, NGAL also increased significantly at the 4th hour (128.18±99 ng/ml, p=0.002) and reached levels close to those in patients with CI-AKI. Unlike new biomarker, however, serum creatinine did not change significantly in this group. The diagnostic power of NGAL is extremely good - AUC 0.847 (95% CI: 0.677-1.000; p=0.001) in CI-AKI and AUC 0.731 (95% CI: 0.539 – 0.924; p=0.024) in subclinical CI-AKI. NGAL may be a reliable biomarker for early diagnosis of clinical and subclinical forms of renal injury after contrast angiographic studies.

This review summarizes current understanding of the interaction between circadian rhythms of gene expression and epigenetic clocks characterized by the specific profile of DNA methylation in CpG-islands which mirror the chronological age of individual cells and the entire organism. Basic mechanisms of regulation for circadian genes CLOCK- BMAL1 as well as downstream clock-controlled genes (ССG) are also discussed here. It has been shown that circadian rhythms operate by finely tuned regulation of transcription and rely on various epigenetic mechanisms including activation of enhancers / suppressors, acetylation / deacetylation of histones and other proteins as well as DNA methylation. Overall, up to 20% of all genes expressed by the cell are subject to expression oscillations associated with circadian rhythms. Also included in the review is a brief list of genes involved in the regulation of circadian rhythms, along with genes important for metabolic control, aging, and oncogenesis. Knocking out some of them (for example, Sirt1) accelerates the aging process, while overexpression of Sirt1, on the contrary, protects against age-related changes. Circadian regulators control a number of genes that activate the cell cycle (Wee1, c-Myc, p20, p21, and Cyclin D1) and regulate histone modification and DNA methylation. Approaches for determining the epigenetic age from methylation profiles across CpG islands in individual cells are described. DNA methylation, which characterizes the function of the epigenetic clock, appears to link together such key biological processes as regeneration and functioning of stem cells, aging and malignant transformation. Finally, main features of adult stem cell aging in stem cell niches and current possibilities for modulating the epigenetic clock as part of antiaging therapy are discussed.

Here, I introduce a concept called autonomous selection to refer to a source of selection that is part of the individuals upon which it acts. The concept is motivated by a set of phenomena with the following characteristics: Natural selection shaped a variant (e.g., gene, epigenetic mark, or combination thereof) to act in a manner that reduces the frequency of one or more heritable traits of the individual in which it is located if those traits are detrimental to individual or group fitness. Phenomena with these characteristics are peculiar to traditional evolutionary theory but have been identified rather frequently in recent decades. They are also relevant to adaptive evolution: By reducing the frequency of a trait detrimental to fitness, the variant accelerates the evolution of adaptations, which allows its holders to adapt better to constantly changing environments. The variant is shaped by (natural) selection, but also does (autonomous) selection. Several phenomena with these characteristics have been invoked by proponents of the extended evolutionary synthesis (EES). The concept of autonomous selection helps resolve some of the controversy surrounding the EES: EES proponents call attention to the incompleteness of contemporary theory, emphasizing individuals’ processes that influence which adaptations those individuals evolve. I argue for the special importance of individuals’ processes that do not just influence those individuals’ adaptations, but also accelerate the adaptive evolution of those individuals. All known phenomena that fit this description are examples of autonomous selection. Other phenomena raised by EES proponents do not meet this threshold.

An experimental study is carried out in a cavitation tunnel on a propeller operating downstream of a non-uniform wake. The goal of this work is to establish quantitative correlations between the near pressure field and the cavitation pattern that takes place on the propeller blades. The pressure field is measured at the walls of the test section and in the near wake of the propeller, and is combined with quantitative high-speed image recording of the cavitation pattern. Through simple harmonic analysis of the pressure data and image processing techniques that allow to retrieve the cavitation extension and volume, we discuss the potential sources that generate the pressure fluctuations. Time correlations are unambiguously established between pressure peak fluctuations and cavitation collapse events, based upon the Rayleigh collapse time. Finally, we design a model to predict the cavitation-induced pressure fluctuations from the derivation of the cavitation volume acceleration. This simple model demonstrates a remarkable agreement with the actual pressure field.

Laser powder bed fusion (LPBF) is an additive manufacturing technique that is gaining popularity for producing metallic parts in various industries. However, parts produced by LPBF are prone to residual stress, deformation, cracks and other quality defects due to uneven temperature distribution during the LPBF process. To address this issue, in prior work, the authors have proposed SmartScan, a method for determining laser scan sequence in LPBF using an intelligent (i.e., model-based and optimization-driven) approach, rather than using heuristics, and applied it to simple 2D geometries. This paper presents a generalized SmartScan methodology that is applicable to arbitrary 3D geometries. This is achieved by: (1) expanding the thermal model and optimization approach used in SmartScan to multiple layers; (2) enabling SmartScan to process shapes with arbitrary contours and infill patterns within each layer; (3) providing the optimization in SmartScan with a balance of exploration and exploitation to make it less myopic; and (4) improving SmartScan's computational efficiency via model order reduction using singular value decomposition. Sample 3D test artifacts are simulated and printed using SmartScan in comparison with common heuristic scan sequences. Reductions of up to 92% in temperature inhomogeneity, 86% in residual stress, 24% in maximum deformation and 50% in geometric inaccuracy were observed using SmartScan, without significantly sacrificing print speed. An approach for using SmartScan for printing complex 3D parts in practice, by integrating it as a plug-in to a commercial slicing software, was also demonstrated experimentally, along with its benefits in significantly improving printed part quality.

Progress in laser-driven proton acceleration requires increasing the proton maximum energy and laser-to-proton conversion efficiency, while reducing the divergence of the proton beam. However, achieving all these qualities simultaneously has proven challenging experimentally, the increase in beam energy often coming at the cost of beam quality. Numerical simulations suggest that coupling multi-PW laser pulses with ultrathin foils could offer a route for such simultaneous improvement. Yet experimental investigations have been limited by the scarcity of such lasers and the need for very stringent temporal contrast conditions to prevent premature target expansion before the pulse maximum. Here, combining the newly commissioned Apollon laser facility that delivers high-power ultrashort (∼24fs) pulses, with a double plasma mirror scheme to enhance its temporal contrast, we demonstrate the generation of up to 35 MeV protons with only 5 J of laser energy. This approach also achieves improved laser-to-proton energy conversion efficiency, reduced beam divergence, and optimized spatial beam profile. Therefore, despite the laser energy losses induced by the plasma mirror, the proton beams produced by this method are enhanced on all accounts compared to those obtained under standard conditions. Particle-in-cell simulations reveal that this improvement results from the intensified electrostatic field caused by a more compact hot-electron distribution.

We propose novel spectrometer designs that aim to enhance the measured spectral range 1 of ions on a finite-sized detector. In contrast to the traditional devices that use uniform magnetic 2 field, in which the deflection of particles increases inversely proportional to their momentum, in a 3 gradient magnetic field, the deflection of particles will be decreased due to the reduction of the 4 magnetic field along their propagation. Low energy ions are particularly impacted, as they are 5 deflected less and are more likely to reach the detector compared to being driven out of it while 6 using a uniform magnetic field. By the means of a gradient magnetic field, the nonlinear dispersion 7 of ions in a homogeneous magnetic field can approach a nearly linear dispersion. Nonetheless, 8 the dispersion of low energy ions in a homogeneous magnetic field remains unnecessarily high. 9 In this article, we explore linear, quadratic, and higher-order field profiles in comparison to the 10 homogeneous field case. We discuss the employed methodology and present simulation results of 11 the spectrometer with an extended ion spectral range, focusing on the minimum detectable energy 12 (energy dynamic range) and energy resolution

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

Laser-targeted weeding methods further enhance the sustainable development of green agriculture, with one key technology being the improvement of weed localization accuracy. Here, we propose an improved YOLOv8 instance segmentation based on bidirectional feature fusion and deformable convolution (BFFDC-YOLOv8-seg) to address the challenges of insufficient weed localization accuracy in complex environments with resource-limited laser weeding devices. Initially, by training on extensive datasets of plant images, the most appropriate model scale and training weights are determined, facilitating the development of a lightweight network. Subsequently, the introduction of the Bidirectional Feature Pyramid Network (BiFPN) during feature fusion effectively prevents the omission of weeds. Lastly, the use of Dynamic Snake Convolution (DSConv) to replace some convolutional kernels enhances flexibility, benefiting the segmentation of weeds with elongated stems and irregular edges. Experimental results indicate that the BFFDC-YOLOv8-seg model achieves a 4.9% increase in precision, an 8.1% increase in recall rate, and a 2.8% increase in mAP50 value to 98.8% on a vegetable weed dataset compared to the original model. It also shows improved mAP50 over other typical segmentation models such as Mask R-CNN, YOLOv5-seg, and YOLOv7-seg by 10.8%, 13.4%, and 1.8%, respectively. Furthermore, the model achieves a detection speed of 24.8 FPS on the Jetson Orin nano standalone device, with a model size of 6.8MB that balances between size and accuracy. The model meets the requirements for real-time precise weed segmentation, suitable for complex vegetable field environments and resource-limited laser weeding devices.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.

Machine Learning deals with creating algorithms capable of learning from the provided data. These systems have a wide range of applications and can also be a valuable tool for scientific research which in recent years has been focused on finding new diagnostic techniques for particle accelerator beams. In this context SPARC_LAB is positioned, a facility located at the Frascati National Laboratories of INFN, where the progress of beam diagnostics is one of the main developments of the entire project. With this in mind, you aim to present the design of two neural networks aimed at predicting the spot size of the electron beam of the plasma-based accelerator at SPARC_LAB, which powers an undulator for the generation of x-ray Free Electron Laser (XFEL). Data-driven algorithms use two different data preprocessing techniques, namely autoencoder neural network and PCA. With both approaches, the predicted measurements can be obtained with an acceptable margin of error and most importantly without activating the accelerator, thus saving time, even compared to a simulator that can produce the same result but much more slowly. The goal is to lay the groundwork for creating a digital twin of linac and conducting virtualized diagnostics using an innovative approach.

Aim: To evaluate the panmacular subthreshold micropulse laser treatment results among patients with central serous chorioretinopathy (CSC) and their correlation with functional and morphological parameters. Material and methods: The examined group included 10 non-treated and 41 treated patients with acute, recurrent, and chronic CSC (13 F, 38 M, mean age 44.11±6.5) and 14 healthy controls (6 F, 8 M, mean age 45±9.3). The BCVA examination, ophthalmoscopy, microp-erimetry, angio-OCT and OCT were performed. The medical history regarding chronic general disorders and known risk factors were recorded. Results: Complete resorption of SRF was obtained in 100% aCSC, 86.66% cCSC, and 63.63% r CSC. BCVA and RetSens significantly improved most of the patients treated in aCSC. The lowest BCVA and RetSens, but the largest pachyvessel and disease duration, were found in rCSC. A strong negative correlation between final BCVA and disease duration was found. No patient demonstrated laser lesions following treatment. Conclusions: The panmacular MPLT therapy leads to long-term enhancement of functional and morphological parameters in all CSC patients. The acute CSC patients showed the most significant improvement. The procedure is safe and could be considered a preferred treatment option for all active CSC cases. Timely treatment is crucial for beneficial outcomes.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

An optical frequency comb (OFC) generator based on an electro-optic Talbot laser and cross-phase modulation (XPM) in a high nonlinear fiber (HNLF) is designed and demonstrated. The Talbot laser is an electro-optic frequency shifting loop to produce repetition rate multiplied pulses, and these pulses working as a pump signal induce XPM process in the HNLF to modulate the phase of a probe signal. At the output of the HNLF, OFCs with a multiplied line-spacing can be generated. The effects of the pump power and the HNLF length on the performance of the generated OFCs are theoretically analyzed. In the experiments, the line-spacing of the generated OFCs is respectively multiplied to be 10 GHz, 15 GHz and 20 GHz with a factor of 2, 3 and 4. The center of the OFCs is tuned in a 4-nm range by adjusting the wavelength of the probe signal.

Global pose refinement is a significant challenge within Simultaneous Localization and Mapping (SLAM) frameworks. For LIDAR-based SLAM systems, pose refinement is integral to correcting drift caused by the successive registration of 3D point clouds collected by the sensor. A divergence between the actual and calculated platform path characterizes this error. In response to this challenge, we propose a linear, parameter-free model, which uses a closed circuit for global trajectory corrections. Our model maps rotations to quaternions and uses Spherical Linear Interpolation (SLERP) for transitions between them. The intervals are established from the constraint set by the Least Squares (LS) method on rotation closure and are proportional to the circuit's size. Translations are globally adjusted in a distinct linear phase. Additionally, we suggest a coarse-to-fine pairwise registration method, integrating Fast Global Registration and Generalized ICP with multiscale sampling and filtering. The proposed approach is tested on three varied datasets of point clouds, including Mobile Laser Scanners and Terrestrial Laser Scanners. These diverse datasets affirm the model's effectiveness in 3D pose estimation with substantial pose differences and efficient pose optimization in larger circuits.

The health and stability of trees are essential information for the safety of people and property in urban greenery, parks or along roads. The stability of the trees is linked to root stability but essentially also to trunk decay. Currently used internal tree stem decay assessment methods, such as tomography or penetrometry, are reliable but usually time-consuming and unsuitable for large-scale surveys. Therefore, a new method based on close-range remote sensed data, specifically close-range photogrammetry and iPhone LiDAR, was tested to detect decayed standing tree trunks automatically. The proposed study used the PointNet deep learning algorithm for 3D data classification. It was verified in three different datasets consisting of pure coniferous trees, pure deciduous trees or mixed data to eliminate the influence of the detectable symptoms for each group and species itself. The mean achieved validation accuracies of the models were 65.5 % for Coniferous trees, 58.4 % for Deciduous trees and 57.7 % for Mixed data classification. The accuracies indicate promising data, which can be either used by practitioners for preliminary surveys or for other researchers to acquire more input data and create more robust classification models.

This study aimed to assess the impact of different modes of laser irradiation on the bactericidal efficacy of aPDT. Dentin plates were prepared by sectioning the crown dentin of bovine teeth infected with Streptococcus sobrinus. Nine aPDTs involving the combinations of three photosensitizers (brilliant blue, BB; acid red, AR; and methylene blue, MB) and three laser irradiation modes (50 mW for 120 s, 100 mW for 60 s, and 200 mW for 30 s) were performed for each infected dentin plate, and the control group consisted of the specimens not applied with aPDT. The bactericidal effects in 10 experimental groups were evaluated (n=11) using both assays of the colony-count and adenosine triphosphate (ATP). The data obtained were analyzed using the Kruskal-Wallis test. The aPDT performed with semiconductor laser in combination with BB, AR, and MB exerted a remarkable bactericidal effect. aPDT with MB exerted a more significant bactericidal effect in the colony-count assay. The results of aPDT performed with varying irradiation times and powers but with constant irradiation energy showed no difference with AR and MB between the modes, whereas BB showed a more significant bactericidal effect when irradiated for a shorter time at a higher irradiation power.

Polyamide 11 (PA11) is a plant-based nylon made from castor beans. Powder bed fusion laser sintering (PBF-LS) is an additive manufacturing process used for PA11 which allows the reuse of the unsintered powder. The unsintered powder is mixed with virgin powders at different refresh rates which has been studied extensively for most semi-crystalline polyamides. However, there is lack of information on the effect of using 100% reused PA11 powder and the number of times it is reused on its own during powder bed fusion laser sintering. This paper investigates the effect of reusing PA11 powder in PBF-LS and number of times it is reused on the dimensional accuracy, density, thermal and tensile properties. From 100% virgin powder to 3rd use of the powder, there is a decrease in powder wastage, decrease in crystallinity and tensile strength. These was associated with the polymerisation and cross-linking process of polymer chains, upon exposure to high temperature. This results in a higher molecular weight and hence density. From the 4th use to 10th reuse, the opposite was observed which was associated to an increase in high-viscosity and un-molten particles which resulted in defects in the PBF-LS parts.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

We present results of the detected voltage distribution of a quantum random number generator based on the photonic integration of semiconductor laser, delay interferometer and photodetector. We find that the integrated system behaves as expected for random number generation from gain-switched laser sources. The biggest advantage is that only electrical connections are needed to operate the system without the need for tricky and expensive optical alignment to external circuitry. We supply results showing that random bit stream created from the random numbers passes the NISTS statistical test suite tests; thus demonstrating the feasibility to generate random number via quantum means at gigabit/s rates from a single photonic integrated circuit. The results are backed by numerical simulations.

The transferability of structure-property relationships for laser-pretreated metal adhesive joints to laser-pretreated metal – carbon fiber reinforced plastic (CFRP) bonds is investigated. Single-lap shear tests were performed on hybrid AW 6082-T6 – CFRP specimens pretreated with the same pulsed laser surface parameter sets on the metal surface as previously tested AW 6082-T6 – E320 metal adhesive joints. The fracture surfaces were characterized to determine the type of failure and elucidate differences and commonalities in the link between surface structures and single-lap shear strengths. Digital image analyses of the hybrid specimens fractured surfaces were used to quantify remaining CFRP fragments on the metallic joint side. The results indicate that high surface enlargements and the presence of undercut structures leads to single-lap shear strengths exceeding 40 MPa and 35 MPa for unaged and aged hybrid specimens respectively. While for the metal-polymer joints the trend from high strength to weakly bonded specimens was largely continuous with the degree of surface structuring, hybrid metal – CFRP joints exhibit a drastic drop in joint performance after aging if the laser-generated surface structures are less pronounced with low surface enlargements and crater depths. Surface features and hydrothermal aging determine whether the specimens fail cohesively or adhesively.

Amorphous germanium films on non-refractory glass substrates were annealed by ultrashort near-infrared (1030 nm, 1.4 ps) and mid-infrared (1500 nm, 70 fs) laser pulses. Crystallization of germanium irradiated at a laser energy density (fluence) range from 25 to 400 mJ/cm2 under single-shot and multi-shot conditions was investigated using Raman spectroscopy. The dependence of the fraction of the crystalline phase on the fluence was obtained for picosecond and femtosecond laser annealings. The regimes of almost complete crystallization of germanium films over the entire thickness are obtained (from the analysis of Raman spectra with excitation of 785 nm laser). The possibility of scanning laser processing is shown, which can be used to create films of micro and nanocrystalline germanium on flexible substrates.

Cyclic olefin copolymer (COC) is a novel type of thermoplastic polymer gaining the attention of the scientific community in electronic, optoelectronic, biomedicine and packaging applications. Despite the benefits in the use of COC like undoubted optical transparency, chemical stability, good water-vapor barrier and biocompatibility, its original hydrophobicity restricts its wider applicability and optimization of its performances. Presently, we report on the optical, and morphological properties of the films of COC covered with Ti in selected areas. The layer of Ti on COC was deposited by pulsed lased deposition processing. The Ti/COC film was characterized by UV-Vis spectroscopy indicating that its transmittance in the visible region decreased by about 20% with respect to the pristine polymer. The quality of the deposited Ti was assessed with the morphology by scanning electron (SEM) and atomic force microscopies (AFM). The modification of the wettability was observed by the sessile drop method indicating a reduction of the native hydrophilicity.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

With the aim to improve cladding coating quality and prevent cracking, this paper established an extreme high-speed laser cladding thermo-mechanical coupling simulation model to study the evolution of the temperature field and residual stress distribution. Process parameters that impacted the macroscopic morphology of single-pass coatings were investigated. Numerical calculations and temperature field simulations were performed based on the process parameter data to validate the effect of the temperature gradient and cooling rate on the coating structure and the residual stress distribution. The results showed that a good coating quality could be achieved using a laser power of 2400 W, a cladding rate of 20 m/min, and a powder feeding rate of 20.32 g/min. The coatings’ cross-sectional morphology corresponded well with the temperature distribution predicted by numerical modeling of the melt pool. The microstructure of the molten coatings is affected by the temperature gradient and cooling rate, which vary greatly from the bottom to the middle to the top. Maximum residual stress appears between the bonding region of the coatings and the substrate, and the coatings themselves have significant residual stress in the form of tensile strains that are mostly distributed in the direction of the laser cladding speed.

With Direct Laser Writing (DLW) maturing in all aspects as a manufacturing technology a toolset for quality assurance must be developed. In this work we want to introduce a first of its kind test artifact. Test artifacts are standardized 3D models with specific geometric feature to evaluate the performance of writing parameters. Test artifacts are already common in other 3D additive manufacturing technologies e.g. Selective Laser Melting. The test artifact introduced in this work was developed in particular to accommodate 1) the high geometrical resolution of DLW structures and 2) the limited possibilities to examine the resulting structure. Geometric accuracy, surface adhesion as well as confocal raman spectroscopy results were considered when evaluating the design of the test artifact. We will explain the individual features and design considerations of our DLW test artifact. The difference between two slicers, Cura and 3DPoli, and the implications on measured feature sizes and the general shape is quantified. The measured geometries are used to derive a general design guide for a specific combination of photoresist, laser power and scanning speed and to analyse the geometric accuracy of a structure produced using these guidelines.

Surface finishing is challenging for additively manufactured components with complex geometries. Magnetic abrasive finishing (MAF) is a promising surface finishing technology that can refine the surface quality of components with complex shapes produced by additive manufacturing. However, there is insufficient study regarding the impact of MAF on microstructure-property relationships for additively manufactured builds, which is critical for evaluating the mechanical performance. Furthermore, although MAF is usually used as the final step of post-processing, it remains unclear whether adjusting the sequence between MAF and other processes, e.g., heat treatment, can potentially improve the mechanical performance. In this work, the effects of MAF on the microstructure and mechanical property evolution of Inconel 718 superalloys made by laser powder bed fusion (LPBF) were studied. The application of MAF was found to significantly reduce the surface roughness of alloys and refine the grain size of aged samples. Moreover, MAF is able to increase the elongation of materials, which can be further influenced by the sequence of MAF and different heat treatments. The highest elongation can be achieved when MAF is performed between homogenization and aging processes. This work demonstrated a promising solution to improving the performance of LPBF Inconel 718 by combining MAF and heat treatment, which provides new perspectives on the post-processing development of additively manufactured alloys for advanced mechanical properties.

Laser reduced graphene oxide (LRGO) on a PET substrate was prepared in one-step to obtain the LRGO grid electrode for sensitive carbaryl determination. The grid form results in a grid distribution of different electrochemically active zones affecting the electroactive substance diffusion towards to the electrode surface and increasing the electrochemical sensitivity for carbaryl determination. Carbaryl is electrochemically irreversibly oxidized by the secondary amine moiety of the molecule with the loss of one proton and one electron in the pH range from 5 to 7 by LSV on the LRGO grid electrode with a scan rate of 300 mV/s. Some interference of the juice matrix molecules did not significantly affect the LSV oxidation current of carbaryl on the LRGO grid electrode after adsorptive accumulation without applied potential. The LRGO grid electrode can be used for LSV determination of carbaryl in fruit juices in the concentration range from 0.25 to 128 mg/L with LOD of 0.1 mg/L by. The fabrication of the LRGO grid electrode opens up possibilities for further inexpensive monitoring of carbaryl in other fruit juices and fruits.

Current commitments by European governments seek to improve energy consumption as a means to reduce carbon emissions from building stock by 2050. Within such context, retrieving reliable three-dimensional contours from point clouds becomes an important step in developing facade retrofitting solutions since facade retrofitting projects often make use of as-built 3D models to help reduce inaccuracies by narrowing interpretation and measurement errors. This work aims to provide a method that uses topology-based parametric modelling for reconstructing building envelopes from point clouds. Through a semi-automated process that gives permanent visual feedback, the user adjusts parameters to custom standards of acceptability. A solution under the form of a Grasshopper definition delivers building envelope 3D contours in various file formats as a means for increasing interoperability. The main contributions of this work consist of a parametric reconstruction workflow capable of solving building topology for retrieving 3D contours, a strategy to bypass point cloud occlusion, and a strategy for converting those contours into an IFC model directly from the parametric modelling environment.

Laser powder bed fusion (L-PBF) is a type of additive manufacturing technology that processes metal powders into a component. Support structures are an essential part of the L- PBF process as they transfer the laser-induced heat during and shortly after the process to the substrate, sustaining positional accuracy of downward facing surfaces of the component. Since the use of support structures is inevitable, optimized designs for them are crucial in realizing more sustainable production process. In a serial production setup, reducing the lead time and cost of a non-value-added process step like support structure removal is of significance when improving the overall business case and competitiveness.The goal of this study was to verify the applicability of lattice-based support structures for L-PBF. To achieve this, different lattice types as support structures were designed. They were tested, compared and verified for a Siemens gas turbine component. The results showed that the generated lattice-based support structures could be suitable for L-PBF. The supports had to be designed appropriately such that they could preserve the geometry of the part. Furthermore, they had to have a short fabrication time and to be removable easily, preferably without machining or sawing.

The aim of this work was to investigate the microstructure and the mechanical properties of la-ser-welded joints combined of DP800 and DP1000 high strength thin steel sheets. The welded joints (WJ) comprised of similar/dissimilar steels with similar/dissimilar thickness were consisted of different zones and exhibited similar microstructural characteristics. The trend of microhard-ness for all WJs was consistent, characterized of the highest value at hardening zone (HZ) and lowest at softening zone (SZ). The degree of softening was more severe and the size of SZ was wider in the WJ combinations of DP1000 than DP800. The tensile test fractures were located at the base material (BM) for all DP800 weldments, while the fractures occurred at the fusion zone (FZ) for the weldments with DP1000 and those with dissimilar sheet thicknesses. The DP800-DP1000 weldment presented similar yield strength (YS) and ultimate tensile strength (UTS) values but lower elongation (EI) in comparison with the DP800-DP800 weldment, which showed similar strength properties as the BM of DP800. However, the EI of DP1000-DP1000 weldment was much lower in comparison with the BM of DP1000. The DP800-DP1000 weldment with dissimilar thicknesses showed the highest YS and UTS values compared with the other weldments, but with the lowest EI. The fatigue fractures occurred at the WJ for all types of weldments. The DP800-DP800 weldment had the highest fatigue limit and DP800-DP1000 with dissimilar thick-nesses had the lowest fatigue limit. The fatigue crack initiated from the weld surface.

The development of high complexity geometry parts is one of the main goals of the additive manufacturing technology. However, the failure of printed structures and the joining of different parts to create complex assemblies represents a real challenge in the research of efficient and sustainability techniques for the permanent assembly of polymers. Laser welding processes have been used as a single step method to join metals until years ago. Nowadays, the growing trend in the use of thermoplastics for additive manufacturing has led to the need to adapt this technique to materials with a very specific nature and more sensitive to thermal effects. Also, the possibility of transmitting the laser beam through transparent polymer layers allows to focus the energy supply on internal sections of the assembled components. In this research, an infrared laser marking system was used to join two different samples of polylactic acid manufactured by fused deposited modeling technology. In order to increase the effectiveness of the bonding process, a transparent and a dark sample have been used as assembly material, focusing the laser beam on the interface area of the two parts. By means of tensile tests, dimensional measurement and the use of optical microscopy techniques, a basis was established that links the supplied energy by laser to the joining performance.

Laser shock peening as an innovative surface treatment technology can effectively improve the fatigue life, sur-face hardness, corrosion resistance, and residual compressive stress. Compared with the laser shock peening, the warm laser shock peening (WLSP) is a new surface treatment technology to improve materials’ surface performances, which takes advantage of thermal mechanical effects on stress strengthening and micro-structure strengthening, results in more stable distribution of the residual compressive stress under heating and cyclic loading process. In this paper, the microstructure of GH4169 nickel super-alloy processed by WLSP technology with differ-ent laser parameters were investigated. The proliferation and tangling of dislocations in GH4169 were observed and the dislocation density increased after WLSP treatment. The influences of different treatment by LSP and WLSP on the microhardness distribution of the surface and along cross-sectional depth were investi-gated. The microstructure evolution of the GH4169 alloy being shocked with WLSP were studied by TEM. The effect of temperature on the stability of high temperature microstructure and properties of GH4169 alloy WLP was investigated.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

Although the concept of additive manufacturing has been proposed for several decades, momentum of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization in SLM to obtain high relative density and low surface roughness simultaneously in the previous literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. The statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. It is noted that the effects of the laser power and scanning speed on the above objective quality show highly significant, while hatch space behaves an insignificant impact. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

The akimotoite--majorite--bridgmanite (Ak--Mj--Bm) triple point in MgSiO3 has been measured in large-volume press (LVP; COMPRES 8/3 assembly) and laser-heated diamond anvil cell (LHDAC). For the LVP data, we calculated pressures from the calibration by Leinenweber (2012). For the LHDAC data, we conducted \textit{in situ} determination of pressure at high temperature using the Pt scale by Dorogokupets and Dewaele (2007) at synchrotron. The measured temperatures of the triple point are in good agreement between LVP and LHDAC at 1990-2000 K. However, the pressure for the triple point determined from the LVP is 3.9+/-0.6~GPa lower than that from the LHDAC dataset. The triple point determined through these experiments will provide an important reference point in the pressure-temperature space for future high-pressure experiments and allow mineral physicists to compare the pressure--temperature conditions measured in these two different experimental methods.

Cellular substructure has been widely observed in the sample fabricated by laser powder bed fusion, while its growth direction and the crystallographic orientation have seldom been studied. This research tries to build a general model to construct the substructure from its two-dimensional morphology. All the three Bunge Euler angles to specify a unique growth direction are determined, and the crystallographic orientation corresponding to the growth direction is also obtained. Based on the crystallographic orientation, the substructure in the single track of austenitic stainless steel 316L is distinguished between the cell-like dendrite and the cell. It is found that, with the increase of scanning velocity, the substructure transits from cell-like dendrite to cell. When the power is 200 W, the critical growth rate of the transition in the single track can be around 0.31 ms^-1.

In laser-assisted milling, higher temperature in shear zone softens the material potentially resulting in a shift of mean residual stress, which significantly affects the damage tolerance and fatigue performance of product. In order to guide the selection of laser and cutting parameters based on the preferred mean residual stress, inverse analysis is conducted by predicting residual stress based on guessed process parameters, which is defined as the forward problem, and applying iterative gradient search to find process parameters for next iteration, which is defined as the inverse problem. An analytical inverse analysis is therefore proposed for the mean residual stress in laser-assisted milling. The forward problem is solved by analytical prediction of mean residual stress after laser-assisted milling. The residual stress profile is predicted through the calculation of thermal stress, by treating laser beam as heat source, and plastic stress by first assuming pure elastic stress in loading process, then obtaining true stress with kinematic hardening followed by the stress relaxation. The variance-based recursive method is applied to solve inverse problem by updating process parameters to match the measured mean residual stress. Three cutting parameters including depth of cut, feed per tooth, and cutting speed, and two laser parameters including laser-tool distance and laser power, are updated with respected to the minimization of resulting residual stress and measurement in each iteration. Experimental measurements are referred on the laser-assisted milling of Ti-6Al-4V grade 5 and ELI. The percentage difference between experiments and predictions is less than 5% for both materials, and the selection is completed within 50 loops.

The underground complicated testing environment and the fan operation instability cause large random errors and outliers of the wind speed signals. The outliers and large random errors result in distortion of mine wind speed monitoring, which possesses safety hazards in mine ventilation system. Application of Kalman filter in velocity monitoring can improve the accuracy of velocity measurement and eliminate the outliers. Adaptive Kalman Filter was built by automatically adjusting process noise covariance and measurement noise covariance depending on the differences between measured and expected speed signals. We analyzed the fluctuation of airflow flow using data of wind speed flow and distribution characteristics of the tunnel obtained by the Laser Doppler Velocimetry system (LDV) studies. A state-space model was built based on the tunnel airflow fluctuations and wind speed signal distribution. The adaptive Kalman Filter was calculated according to the actual measurement data and the Expectation Maximization (EM) algorithm. The adaptive Kalman filter was used to shield fluid pulsation while preserving system-induced fluctuations. Using the Kalman filter to treat offline wind speed signal acquired by LDV, the reliability of Kalman filter wind speed state model and the characteristics of adaptive Kalman Filter were investigated. Results showed that the adaptive Kalman filter effectively eliminated the outliers and reduced the root-mean-squares error (RMSE), and the adaptive Kalman filter had better performance than the traditional Kalman filter in eliminating outliers and reducing RMSE. Field experiments in online wind speed monitoring were conducted using the optimized adaptive Kalman Filter. Results showed that adaptive Kalman filter treatment could monitor the wind speed with smaller RMSE compared with LVD monitor. The study data demonstrated that the adaptive Kalman filter is reliable and suitable for online signal processing of mine wind speed monitor.

A realistic implementation of an all-fiber CO₂ sensor, using 74 cm of hollow core PCF fiber as the cavity for light/gas interaction, has been implemented. It is based on CO₂ absorbance in the 2 μm region. The working range is from 2% to 100% CO₂ concentration at 1 atm total pressure. The response time obtained was 10 min. The use of an FBG tuned fiber ring laser, specifically designed for this application, is discussed and preliminary results with this laser are also presented.

The limitations of investment casting of cobalt-based alloys are claimed to be less problematic with significant improvements in metal additive manufacturing by selective laser melting (SLM). Despite these advantages, the metallic devices are likely to display mechanical anisotropy in relation to build orientations, which could consequently affect their performance ‘in vivo’. In addition, there are inconclusive evidence concerning the requisite composition and post-processing steps (e.g. heat-treatment to relieve stress) that must be completed prior to the devices being used. In the current paper, we evaluate the microstructure of ternary cobalt-chromium-molybdenum (Co-Cr-Mo) and cobalt-chromium-tungsten (Co-Cr-W) alloys built with Direct Metal Printing and LaserCUSING SLM systems respectively at 0°, 30°, 60° and 90° inclinations (Φ) in as-built (AB) and heat-treated (HT) conditions. The study also examines the tensile properties (Young's modulus, E; yield strength, R_P0.2; elongation at failure, A_t and ultimate tensile strength, R_m), relative density (RD), and micro-hardness (HV5) and macro-hardness (HV20) as relevant physico-mechanical properties of the alloys. Data obtained indicate improved tensile properties and HV values after short and cost-effective heat-treatment cycle of Co-Cr-Mo alloy; however, the process did not homogenize the microstructure of the alloy. Annealing heat-treatment of Co-Cr-W led to significant isotropic characteristics with increased E and A_t (except for Φ = 90º) in contrast to decreased R_P0.2, R_m and HV values, compared to the AB form. Similarly, the interlaced weld-bead structures in AB Co-Cr-W were removed during heat-treatment, which led to a complete recrystallization in the microstructure. Both alloys exhibited defect-free microstructures with RD exceeding 99.5%.

The ultramafic-hosted Kairei vent field, located at 25°19′S, 70°02′E towards the northern end of the segment 1 of the Central Indian Ridge (CIR-S1) in a water depth of ~2450 m. This study aims to investigate the distribution of trace elements among sulfides of differing textures, and discuss the possible factors controlling the trace element distribution in those minerals by using LA-ICP-MS spot analyses as well as line scans. Our results show that there are distinct systematic trace element distributions throughout the different minerals：(1) Pyrite is divided into three types at the Kairei, including early-stage euhedral pyrites (py-I), sub-euhedral pyrites (py-II), and colloform pyrites (py-III). Pyrite is generally enriched in Mo, Au, As, Tl, Mn, and U. py-I have higher contents of Se, Te, Bi, and Ni, py-II are enriched in Au relative to py-I and py-III, but poor in Ni, py-III are enriched in Mo, Pb, and U but are poor in Se, Te, Bi, and Au. Variations in the concentrations of Se, Te, and Bi in pyrite are likely governed by the strong temperature gradient. Ni is generally lower than Co in pyrites, indicates that our samples precipitated at a high-temperature condition, whereas the extreme Co enrichment is likely from a magmatic heat source combined serpentinization reactions underlie the deposits. (2) Chalcopyrite is characterized by high concentrations of Co, Se, Te. The abundant of Se and Te in chalcopyrite cause by the high solubilities of Se and Te incorporated into chalcopyrite lattice at high temperature fluids. The concentration of Sb, As and Au is relatively low in chalcopyrite from the Kairei vent field. (3) Sphalerite from both the Zn-rich chimney is characterized by high concentrations of Sn, Co, Ga, Ge, Ag, Pb, Sb, As, and Cd, but depleted in Se, Te, Bi, Mo, Au, Ni, Tl, Mn, Ba, V, and U in comparison with the other minerals. The high concentration of Cd and Co is likely caused by the substitution of Cd2+ and Co2+ for Zn2+ in sphalerite. A high concentration of Pb accompanied by high Ag concentration in sphalerite indicating the Ag occurs in the microinclusions of Pb-bearing minerals such as galena. Au is generally low in sphalerite and strong correlate with Pb suggesting its presence in the microinclusions of galena. The strong correlation of As with Ge in sphalerite from Kairei suggests that they might precipitate under medium- to low-temperature with moderately reduced conditions. (4) Bornite-digenite is very low in most trace elements, except for Co, Se, and Bi. The high concentration of Se and Bi in all the sulfide minerals was observed in bornite-digenite can be explained by abundant Bi-selenide inclusions. Serpentinization in ultramafic-hosted hydrothermal systems might play an important role on Au enrichment in pyrite with low As contents. Compared with felsic-hosted seafloor massive sulfide (SMS) deposits, sulfide minerals from the ultramafic-hosted deposits show higher concentrations of Se and Te, but lower As, Sb, and Au concentrations attributed to the contribution of magmatic volatile input. Significant Se enrichment in chalcopyrite has been found from mafic-hosted SMSs indicate that the primary factor that controls the Se enrichment is its temperature-controlled mobility in fluids.

It was demonstrated during the past decade that ultra-short intense laser pulse tightly focused deep inside a transparent dielectric generates the energy density in excess of several MJ/cm$^3$. Such energy concentration with extremely high heating and quenching rates leads to unusual solid-plasma-solid transformation paths overcoming kinetic barriers to formation of previously unknown high-pressure material phases, which are preserved in the surrounding pristine crystal. These results were obtained with the pulse of Gaussian shape in space and in time. Recently it was shown that the Bessel-shaped pulse could transform much larger amount of a material and allegedly create even higher energy density than that was achieved with the Gaussian (GB) pulses. Here we present a succinct review of previous results and discuss the possible routes for achieving higher energy density employing the Bessel beams (BB) and take advantage of its unique properties.

Cells take decisions on their responses depending on the stimuli received by the surrounding extracellular environment, that provides the essential cues at the micro and the nano-lengthscales required for adhesion, orientation, proliferation and differentiation. In this study, discontinuous microcones on silicon (Si) and continuous microgrooves on polyethylene terephthalate (PET) substrates were fabricated via ultrashort-pulsed laser irradiation at various fluences, resulting in microstructures with different roughness and geometrical characteristics. The topographical models attained were specifically developed to imitate the guidance and alignment of Schwann cells for oriented axonal regrowth, towards nerve regeneration. At the same time, positive replicas of the silicon microstructures formed were successfully reproduced, via soft lithography, on the biodegradable polymer poly(lactide-co-glycolide) (PLGA). The anisotropic continuous (PET) and discontinuous (PLGA replicas) microstructured polymeric substrates were assessed in terms of their influence on the Schwann cells responses. It is shown that the developed micropatterned substrates enable control over the cellular adhesion, proliferation and orientation and are thus useful to engineer cell alignment in vitro. This property could be potentially useful in the fields of neural tissue engineering and for dynamic microenvironment systems that simulate in vivo conditions.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

Smith-Magenis syndrome is a complex neurobehavioral genetic disorder. The spectrum of SMS phenotype is broad but commonly includes craniofacial, neurobehavioral, and otolaryngologic features. While the etiology of SMS is commonly attributed to one copy interstitial deletion in the 17p11.2 region (90-95% of cases), variants identified by sequence analysis in RAI1 have also been reported in 5-10% of cases. The phenotypic spectrum of patients with RAI1 sequence alterations is not clear. In this study, we report a 9-year-old male with global cognitive and psychomotor developmental delay, musculoskeletal and cardiovascular abnormalities, and dysmorphic craniofacial features. Whole genome quad analysis of the proband, unaffected parent, and unaffected brother identified a novel de novo RAI1:c.2736delC variant. This is the first report of this variant in the literature. This report also highlights the details of the genome analysis and this patient's phenotypic spectrum.

Background: Acute kidney injury (AKI) and contrast-induced nephropathy (CIN) are common complications following percutaneous coronary intervention (PCI) or coronary angiography (CAG), presenting significant clinical challenges. Machine learning (ML) models offer promise for improving patient outcomes through early detection and intervention strategies. Methods: A comprehensive literature search following PRISMA guidelines was conducted in PubMed, Scopus, and Embase from inception to June 11, 2024. Study characteristics, ML Models, performance metrics (AUC, accuracy, sensitivity, specificity, precision), and risk of bias assessment using the PROBAST tool were extracted. Statistical analysis used a random-effects model to pool AUC values, with heterogeneity assessed via the I² statistic. Results: From 431 initial studies, 14 met the inclusion criteria. Gradient Boosting Machine (GBM) and Support Vector Machine (SVM) models showed the highest pooled AUCs of 0.87 (95% CI: 0.82-0.92) and 0.85 (95% CI: 0.80-0.90), respectively, with low heterogeneity (I² < 30%). Random Forest (RF) had a similar AUC of 0.85 (95% CI: 0.78-0.92) but significant heterogeneity (I² > 90%). Multilayer Perceptron (MLP) and XGBoost models had moderate pooled AUCs of 0.79 (95% CI: 0.74-0.84) with high heterogeneity. RF showed strong accuracy (0.83, 95% CI: 0.70-0.96), while SVM had balanced sensitivity (0.69, 95% CI: 0.63-0.75) and specificity (0.73, 95% CI: 0.60-0.86). Age, serum creatinine, left ventricular ejection fraction, and hemoglobin consistently influenced model efficacy. Conclusions: GBM and SVM models, with robust AUCs and low heterogeneity, are effective in predicting AKI and CIN post-PCI/CAG. RF, MLP, and XGBoost, despite competitive AUCs, showed considerable heterogeneity, emphasizing the need for further validation.

Thrombosis is the pathological clot formation under abnormal hemodynamic conditions, which can result in vascular obstruction, causing ischemic strokes and myocardial infarction. Thrombus growth under moderate to low shear (<1000 s^-1) relies on platelet activation and coagulation. Thrombosis at elevated high shear rates (>10,000 s-1) is predominantly driven by unactivated platelet binding and aggregating mediated by von Willebrand factor (VWF), while platelet activation and coagulation are secondary in supporting and reinforcing the thrombus. Given the molecular and cellular level information it can access, multiscale computational modelling informed by biology can provide new pathphysiological mechanisms that are otherwise not accessible experimentally, holding promise for novel first-principle-based therapeutics. In this review, we summarize the key aspects of platelet biorheology and mechanobiology, focusing on the molecular and cellular scale events and how they build up to thrombosis through platelet adhesion and aggregation in the presence or absence of platelet activation. In particular, we highlight recent advancements in multiscale modeling of platelet biorheology and mechanobiology and how they can lead to better prediction and quantification of thrombus formation, exemplifying the exciting paradigm of digital medicine.

The theory of heavy ion double charge exchange (DCE) reactions proceeding by effective rank–2 isotensor interactions is presented. Virtual pion–nucleon charge exchange interactions are investigated as the source for induced isotensor interactions, giving rise to the Majorana DCE (MDCE) reaction mechanism. MDCE is of a generic character, proceeding through pairs of complementary (π±,π∓) reactions in the projectile and target nucleus. The dynamics of the elementary processes is discussed where the excitation of pion–nucleon resonances are of central importance. Investigations of initial and final state ion–ion interactions show that these effects are acting as vertex renormalizations. In closure approximation, well justified by the finite pion mass, the second order transition matrix elements reduce to pion potentials and effective two–body isotensor DCE interactions, giving rise also to two–body correlations in either of the participating nuclei. Connections to neutrinoless Majorana double beta decay (MDBD) are elucidated at various levels of dynamics, from the underlying fundamental electro–weak and QCD scales to the physical scales of nuclear MDBD and MDCE physics. It is pointed out that heavy ion MDCE reactions may also proceed by competing electro–weak charge exchange processes, leading to lepton MDCE by electrons, positrons, and neutrinos.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

A recent study revealed a persistent presence of the PP-Spike recombinant protein in 50% of individuals who received ModRNA injections, contrasting with unvaccinated controls, whether SARSCoV-2 infected or not, up to 187 days post-injection. The implications of these findings are discussed in the context of PP-Spike recombinant protein-induced hyperimmune/inflammatory reactions and thrombotic vasculitis as mechanisms to elucidate the serious side effects, long-term organ complications, and excess deaths observed after administering Covid ModRNA products. These results underscore the urgent need for a comprehensive reassessment of the risk-benefit profile of ModRNA injections, including an immediate halt in their use for any person, and a renewed emphasis on understanding and addressing their long-term effects on human health

Earthquakes often entail alterations in the groundwater flow regime, in the phreatic level, in the surge and loss of springs, and discharge in brooks and springs. As for the latter, there are diverse feasible mechanisms, so there is a variety of theoretical approaches to elucidate the post-earthquake effects on spring discharge. This study adopts a conceptual approach, primarily presenting various methods for estimating water released by earthquakes by calculating discharge surpluses in springs. This study delves into refined techniques rooted in groundwater hydraulics, displaying applications of analytical and simulation methodologies to quantify seismic-induced groundwater discharge in springs. Investigating springs as natural indicators, this research applies mathematical precipitation-runoff models, specifically the CREC model, for simulating hydrographs in post-earthquake scenarios. We apply analytical procedures or mathematical simulation techniques employed in groundwater hydraulics for natural aquifer recharge calculations. Firstly, we briefly describe the methods based on the analysis of depletion curves of hydrographs in spring discharge. Additionally, certain mathematical rainfall-runoff models utilized in simulating hydrographs of karstic springs, along with derived analytical approximations, are adapted for this scenario. These hydraulic calculations involve the depletion coefficient and hydrodynamic volumes of aquifers, parameters that reveal certain aspects of the relation between groundwater and earthquakes, such as: a) Acknowledging faults as the primary geological structures in transmitting pore pressures due to earthquakes. b) Clarifying mechanisms of permeability enhancement during earthquakes. c) Highlighting the substantial volumes in motion within the Earth's interior, which, for instance, could constitute a significant source for the origin of mineral deposits. The findings highlight diverse features of the complex interplay between hydrogeological and tectonic processes at challenging spatial and temporal scales.

Background: Idiopathic pulmonary fibrosis (IPF) is a fatal lung disease of unknown origin, with a median survival time of ~3 years after diagnosis without anti-fibrotic therapy. It is characterized by progressive fibrosis indicated by increased collagen deposition and high numbers of fibroblasts in the lung. It was demonstrated that CCL18 induces collagen and αSMA synthesis in fibroblasts. We aimed to identify the CCL18 receptor responsible for its pro-fibrotic activities. Methods: We used a random phage display library to screen for potential CCL18-binding peptides, demonstrated its expression in human lungs and fibroblast lines by PCR and immunostaining and verified its function in cell lines. Results: We identified CCR6 (CD196) as a CCL18 receptor and found its expression in fibrotic lung tissue and on lung fibroblast lines derived from fibrotic lungs but it is almost absent in control lines and tissue. CCL18 induces receptor-internalization in a CCR6-overexpressing cell line. CCR6 blockade in primary human lung fibroblasts reduces CCL18-induced FGF2 release as well as collagen-1 and αSMA expression. Knock-down of CCR6 in a mouse fibroblast cell line abolishes the induction of collagen and -smooth muscle actin expression. Conclusion: Our data indicate that CCL18 triggers pro-fibrotic processes via CCR6, highlighting its role in fibrogenesis.

Drug-induced pruritus triggers a desire to scratch, thereby diminishing one’s quality of life. Certain instances of this phenomenon follow complex mechanisms of action that diverge from histamine-mediated pathways, known contributors to pruritus. However, investigations into the relationship between drugs and pruritus are limited. In this study, data mining techniques were employed to comprehensively analyze the characteristics of drugs linked to pruritus, using the FDA Adverse Event Reporting System(FAERS) Data maintained in the United States. Reports linked to pruritus demonstrated noteworthy differences in gender, age, and weight when compared with non-pruritus cases. Among the leading candidates for drugs prompting pruritus were ophthalmic drugs, systemic antibacterials, contrast media, dermatological antifungals, and dermatological preparations. Principal component analysis showed that the second principal component served as an indicator for distinguishing between onsets at mucous membranes or the skin surface. Additionally, the third principal component functioned as an indicator for categorizing administration methods as either invasive or noninvasive. Furthermore, a hierarchical cluster analysis conducted on these obtained principal components revealed the potential for classifying drugs based on the site of pruritus onset and the method of drug administration. These findings contribute to the development of targeted prevention and treatment strategies for avoiding pruritus in clinical practice.

The time-resolved CIDNP method can provide information about degenerate exchange reactions (DEE) involving short-lived radicals. In the temperature range from 8 to 65°C, the DEE reactions of the guanosine-5’-monophosphate anion GMP(-H)- with the neutral radical GMP(-H)•, of the N-acetyl tyrosine anion NacTyrO- with a neutral radical NacTyrO• and of the tyrosine anion TyrO- with a neutral radical TyrO• were studied. In all the studied cases, the radicals were formed in the reaction of quenching triplet 2,2’-dipyridyl. The reorganization energies were obtained from Arrhenius plots. The rate constant of the reductive electron-transfer reaction in pair GMP(-H)•/TyrO- was determined at T = 25°C. Rate constants of GMP(-H)• radical reduction reactions with TyrO- and NacTyrO- anions calculated by the Marcus cross relation differ from the experimental ones by two orders of magnitude. The rate constants of several other electron transfer reactions involving GMP(-H)-/•, NacTyrO-/•, and TyrO-/• pairs calculated by cross relation agree well with the experimental values. The rate of nuclear paramagnetic relaxation was found for the 3,5 and β-protons TyrO• and NacTyrO•, the 8-proton GMP(-H)• the 3,4-protons DPH• at each temperature. In all cases, the dependences of the rate of nuclear paramagnetic relaxation on temperature are described by the Arrhenius dependence.

Abstract: The trend of fasting until noon (omission or delayed breakfast) is increasingly prevalent in modern society. This eating pattern triggers discordance between endogenous circadian clock rhythms and the feeding/fasting cycle and is associated with an increased incidence of obesity and T2D. Although the underlying mechanism of this association is not well understood, growing evidence suggests that fasting until noon, also known as an “extended postabsorptive state,” has the potential to cause a deleterious effect on clock gene expression and disrupted regulation of body weight, postprandial and overall glycemia, skeletal muscle protein synthesis, appetite and may also lead to lower energy expenditure. This manuscript overviews the clock gene-controlled glucose metabolism during the active and resting phases. The consequences of postponing until noon the transition from postabsorptive to fed state on glucose metabolism, weight control, and energy expenditure. Finally, we will discuss the metabolic advantage of shifting more energy, carbohydrates (CH), and proteins to the early hours of the day.

Genetic sensorineural hearing loss and Meniere disease have been associated with rare variations in the coding and non-coding region of the human genome. Most of these variants are classified as likely pathogenic or variants of unknown significance and require functional validation in cellular or animal models. Given the difficulties to obtain human samples and the raising concerns about animal experimentation, human induced pluripotent stem cells emerge as cellular models to investigate the interaction of genetic and environmental factors in the pathogenesis of inner ear disorders. The generation of human sensory epithelia and neuron-like cells carrying the variants of interest may facilitate a better understanding of their role during differentiation. These cellular models will allow us to explore new strategies for restoring hearing and vestibular sensory epithelia as well as neurons. This review summarizes the use of human induced pluripotent stem cells in sensorineural hearing loss and Meniere disease and proposes some strategies for its application in clinical practice.

Background: Both natural immunity and vaccine-induced immunity to COVID-19 may be useful to reduce the mortality/morbidity of this disease, but still a lot of controversy exists. Aims: This narrative review analyzes the literature about: a) the duration of natural immunity; b) cellular immunity; c) cross-reactivity; d) the duration of post-vaccination immune protection; e) the probability of reinfection and its clinical manifestations in the recovered patients; f) comparisons between vaccinated and unvaccinated in the possible reinfections; g) the role of hybrid immunity; h) the effectiveness of natural and vaccine-induced immunity against Omicron variant; i) comparative incidence of adverse effects after vaccination in recovered individuals vs. COVID-19-naïve subjects. Material and Methods: through multiple search engines we investigated COVID-19 literature related to the aims of the review, published since April 2020 through July 2022, including also the previous articles pertinent to the investigated topics. Results: nearly 900 studies were collected and 238 pertinent articles were included. It was highlighted that the vast majority of individuals after COVID-19 develop a natural immunity both of cell-mediated and humoral type, which is effective over time and provides protection against both reinfection and serious illness. Vaccine-induced immunity was shown to decay faster than natural immunity. In general, the severity of the symptoms of reinfection is significantly lower than in the primary infection, with a lower degree of hospitalizations (0.06%) and an extremely low mortality. Conclusions: this narrative review regarding a vast number of articles highlighted the valuable protection induced by the natural immunity after COVID-19, which seems comparable or superior to the one induced by anti-SARS-CoV-2 vaccination. Vaccination of the unvaccinated COVID-19-recovered subjects may not be indicated. Further research is needed in order to: a) measure the durability of immunity over time; b) evaluate both the impacts of Omicron-5 on vaccinated and healed subjects and of hybrid immunity.

Plasmodium falciparum dihydroorotate dehydrogenase (PfDODH) is one of the enzymes currently explored in the treatment of malaria. Although there is currently no clinically approved drug targeting PfDODH, many of the compounds in clinical trials have [1, 2, 4,] triazolo [1, 5-a] pyrimidin-7-amine backbone structure. This study sought to design new compounds from the fragments of known experimental inhibitors of PfDODH. Nine experimental compounds retrieved from Drug Bank online were downloaded and broken into fragments using Schrodinger power shell; the fragments were recombined to generate new ligand structures using BREED algorithm. The new compounds were docked with PfDODH crystal structure, after which the compounds were filtered with extensive drug-likeness and toxicity parameters. A 2D-QSAR model was built using the multiple linear regression method and externally validated. The compounds electronic behaviours were studied using DFT calculations. Structural investigation of the six designed compounds, which had lower binding energies than the standard inhibitors, showed that five of them had [1, 2, 4,] triazolo [1, 5-a] pyrimidin-7-amine moieties and interacted with essential residues at the PfDODH binding site. In addition to their drug-like and pharmacokinetic properties, they also showed minimal toxicities. The externally validated 2D-QSAR model with R² and Q² values of 0.6852 and 0.6691, confirmed the inhibitory prowess of these compounds against PfDODH. The DFT calculations showed regions of the molecules prone to electrophilic and nucleophilic attack. The current study thus provides insight into the development of a new set of potent PfDODH inhibitors.

Introduction: Wound healing is a multifaceted biological process, and diabetic wounds add more complexity to it. In diabetic wounds, the combination of chloroform fractions of Achyranthes aspera L. (A.aspera) leaves with β-Glucans has not been investigated. The additive effect of these two (A.aspera + β-Glucans) would benefit the inflammatory phase of diabetic wounds, as improper treatment will lead to chronic injuries. Therefore, the goal of this research work was to assess the in-vivo wound healing and anti-inflammatory effects of a combination of chloroform fractions of A.aspera leaves and β-Glucans in a variety of wound models in STZ-induced diabetic rats. Methods: Preliminary phytochemical analyses of A.aspera were conducted to identify various phytoconstituents in the test extract. Acute and sub-acute dermal toxicity tests of A.aspera were carried out on mice and rats, respectively, to see whether there were any abnormalities. Excision and incision wound models, cotton pellet-induced granuloma models, rat paw edema and burn wounds were used to test wound healing and anti-inflammatory actions. To induce diabetes, streptozotocin (STZ) was administered intraperitoneally at a dosage of 65 mg/kg (i.p.). A.aspera (10% w/w) and β-Glucans (2% w/w) ointments were tested separately and in combination for wound healing activities. Silver sulfadiazine (1 % w/w) ointment was used to treat the positive control groups. Excision wound model rats that had been treated with basic ointment were used as negative controls, as were incision wound model rats that had not been treated. A.aspera (400 mg/kg, po) and β-Glucans (30 mg/kg, po) were tested separately and in combination for anti-inflammatory efficacy. Positive control groups were given indomethacin (10 mg/kg, po) for cotton pellet-induced granuloma and rat paw oedema models. Negative controls for both anti-inflammatory activity models were provided 2% Tween 80. The groups were made up of six rats, and the treatments were given topically and orally to assess wound healing and anti-inflammatory effects. The levels of hydroxyproline and hexosamine and the antioxidant enzymes (SOD and CAT) in the granulation tissue were measured in excision wound model. Healed excision wound skin was examined histopathologically. Results: The A.aspera and β-Glucans combination resulted in a significant percentage of wound contraction and a shorter epithelialization time (P<0.01). The combination was found to be the most effective, with the highest percentage of edema reduction (55 %; p<0.01). The combination also exhibited favourable hydroxylamine, hexosamine and anti-oxidant profiles supported by histopathology data. Conclusion: This research showed that the immunomodulatory effect of β-Glucans had significantly enhanced the wound healing, anti-inflammatory, and anti-oxidant potential of A.aspera in diabetic wounds.

Keywords: Chemical Intolerance, Drug Intolerance, Food Intolerance, QEESI, BREESI, Multiple Chemical Sensitivity, Toxicant-induced Loss of Tolerance, Prevalence

Immunotherapy has gained great momentum with chimeric antigen receptor T cell (CAR-T) therapy, in which patient’s T lymphocytes are genetically manipulated to recognize tumor-specific antigens increasing tumor elimination efficiency. In the last years, CAR-T cell immunotherapy for hematological malignancies achieved a great response rate on patients and is a very promising therapy for several other malignancies. Each new CAR design requires a preclinical proof-of-concept experiment using immunodeficient mouse models. The absence of a functional immune system in these mice makes them simple and suitable to be mathematically modeled. In this work, we developed a three population mathematical model to describe tumor response to CAR-T cell immunotherapy in immunodeficient mouse models, encompassing interactions between a non-solid tumor and CAR-T cells (effector and long-term memory). We account for several phenomena, such as tumor-induced immunosuppression, memory pool formation, and conversion of memory into effector CAR-T cells in the presence of new tumor cells. Individual donor and tumor specificities were considered as uncertainties in the model parameters. Our model is able to reproduce several CAR-T cell immunotherapy scenarios, with different CAR receptors and tumor targets reported in the literature. We found that therapy effectiveness mostly depends on some specific parameters such as the differentiation of effector to memory CAR-T cells, CAR-T cytotoxic capacity, tumor growth rate, and tumor-induced immunosuppression. In summary, our model can contribute to reduce and optimize the number of in vivo experiments with in silico tests to select specific scenarios that could be tested in experimental research. Such in silico laboratory was made available in a Shiny R-based platform called CARTmath. It is an open-source, easy to run simulator, available at github.com/tmglncc/CARTmath or directly on the webpage cartmath.lncc.br, containing this manuscript results as examples and documentation. The developed model, together with the CARTmath platform, provides potential use for assessing different CAR-T cell immunotherapy protocols and associated efficacy, becoming an accessory towards in silico trials.

Recently, several research groups have reported on anomalous enhancement of the self-field critical currents, Ic(sf,T), at low temperatures in superconductor/Dirac-cone material/superconductor (S/DCM/S) junctions. Some papers attributed the enhancement to the low-energy Andreev bound states arising from winding of the electronic wave function around DCM. In this paper, Ic(sf,T) in S/DCM/S junctions have been analyzed by two approaches: modified Ambegaokar-Baratoff and ballistic Titov-Beenakker models. It is shown that the ballistic model is an inadequate tool to analyze experimental data from S/DCM/S junctions. The primary mechanism for limiting superconducting current in S/DCM/S junctions is different from the conventional view that the latter is the maximum value within the order parameter phase variation. Thus, there is a need to develop a new model for self-field critical currents in S/DCM/S systems.

An increasing number of aircraft is equipped with wing tip devices, which either are installed by the aircraft manufacturer at the production line or are retrofitted after the delivery of the aircraft to its operator. Installation of wing tip devices has not been a popular choice for regional turboprop aircraft and the novelty of the current study is to investigate the feasibility of retrofitting the British Aerospace (BAe) Jetstream 31 with an appropriate wing tip device (or winglet) to increase its cruise range performance, taking also into account the aerodynamic and structural impact of the implementation. To the best of the knowledge of the authors, no previous study exists which has attempted to assess the winglet retrofit of an existing aircraft type of similar size and operating profile. The optimal winglet design achieved a 2.38% increase of the maximum range by reducing the total drag by 1.19% at a mass penalty of 3.25%, as compared with the baseline aircraft configuration. Other designs were found to be more effective in reducing the total drag, but the structural reinforcement required for their implementation outweighed the achieved performance improvements. Since successful winglet retrofit programs for typical short to medium range narrow body aircraft report even more than 3% of block fuel improvements, undertaking the project of installing an optimal winglet design to the BAe Jetstream 31, should also consider a Direct Operating Cost (DOC) assessment on top of the aerodynamic and structural aspects of the retrofit.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

Lanthanides and actinides are emerging contaminants, but little is known about their uptake and distribution by plants and their interactions in the rhizosphere. To better understand the fate of these metals in plants, we assessed the bioassociation of 2, 20 and 200 µM Eu(III) by five hydroponically grown crops endemic to Europe. The metal’s concentration and its speciation was monitored by inductively coupled plasma mass spectrometry and laser spectroscopy, whereas root exudation was investigated by chromatographic methods. It has been shown, that Eu(III) bioassociation is a two-stage process, involving rapid biosorption followed by accumulation in root tissue and distribution to the stem and leaves. Within 96 h of exposure time, the plant induces a change of Eu(III) speciation in the liquid medium, from a predominant Eu(III) aquo species, as calculated by thermodynamic modelling, to a species with longer luminescence lifetime. Root exudates such as citric, malic, and fumaric acid were identified in the cultivation medium and affect Eu(III) speciation in solution, as was shown by a change in the thermodynamic model. These results contribute to a comprehensive understanding of the fate of lanthanides in the biosphere and provide a basis for further investigations with the chemical analogues Cm(III) and Am(III).