The aim of this study was to determine the correlation between the external friction angle of cereal kernels and the roughness of a steel friction plate. The experiment was performed on the kernels of five principal cereals: wheat, rye, barley, oats and triticale. Flat seed units composed of three spaced kernels joined by adhesive tape were analyzed in each experimental variant. The external friction angle of flat seed units was determined on 9 steel friction plates with different roughness. Measurements were performed in 3 replications with a photosensor device which registered the external friction angle of cereal kernels. On friction plates with surface roughness Ra=0.36 to Ra=6.72, the average values of the angle of external friction ranged from 17.56° in rye kernels to 34.01° in oat kernels. The greatest similarities in the angle of external friction were observed between wheat and triticale kernels, whereas the greatest differences were noted between barley and oat kernels and between barley and triticale kernels. Friction plates made of ST3S steel should be characterized by the lowest surface roughness to minimize energy consumption during grain processing. The optimal surface roughness of steel friction plates was determined at Ra=0.9.

The design of curved surface sliders (CSS) based on the elastic response spectrum is done by iteration to find the combination of friction coefficient and displacement capacity which satisfies the condition that the maximum horizontal CSS force is equal to the horizontal force of the structure. Although this CSS design is valid it does not necessarily minimize structural acceleration. This paper therefore describes the optimum CSS design for minimum structural acceleration. All valid CSS designs and the optimum CSS design are represented by their associated trajectory in the elastic response spectrum plane which visualizes the optimization problem. The results demonstrate that the optimum CSS design is not obtained at maximum tolerated effective damping ratio. The subsequent sensitivity analysis describes how much the structural acceleration increases if the actual friction coefficient of the real CSS deviates from its optimum design value. The analysis points out that the increase in structural acceleration is approximately one order of magnitude smaller than the deviation in friction. The sensitivity data may be used by structural engineer to determine tolerable deviations in friction coefficient which still results in acceptable structural accelerations.

Analysis of water resources of this area was carried out in order to assessing the water quality by determining the concentrations of Cations, Anions, Heavy metals, Trace elements, PH, Alkalinity, Total Dissolved Solids and microbial loads in water samples. Ten (10) water samples were collected from the study area - samples each of rain water, two pond waters - 1 and 2, stream water, four (4) hand-dug wells, hand pump water and a motorized borehole. The results obtained were compared with WHO standards and it showed that all the cations in water samples are within the limits. The water samples at locations B, E, F, G, H, I, and J have high alkalinity and HC0^-₃ content. The heavy metals (Pb, Ni and Cd) and trace elements (Fe and Cu) are dominantly high in the surface waters. Microbiological substances in the water samples from the study area revealed indicator organisms higher than the WHO standard for drinking water. Samples obtained from location G, I and J recorded an absence of E. coli and are fit for human consumptions but needed to be treated due to high MPN (Most Probable Number) index of viable microorganisms as against WHO standard. This research showed that the water resources of the study area are gradually polluted and in the near future may not be good for drinking.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

In this work, the apparent shear strength at the interface between a bamboo fiber and the surrounding poly(lactic acid) (PLA) matrix is quantified. A method for processing pull-out test samples within a controlled embedded length is proposed and the details of the test procedure are presented, along with a critical discussion of the results. Two series of samples are considered: untreated and mercerized bamboo fibers from the same batch, embedded in the same polyester matrix. Electron and optical microscopy are used to observe the fiber-matrix interface before and after the test, and to identify the failure mode of each sample, especially as regards the occurrence of fibrillation in the fiber bundles. The values of apparent interfacial shear strength are calculated only for regular fibers successfully pulled out from the matrix, and reported with their statistical variations. Mercerization, whose efficiency was proven by Fourier Transform InfraRed (FTIR) spectroscopy, did not appear though to improve the quality of the interface (τ_app = 7.0 ± 3.1 MPa for untreated fibers and τ_app = 5.3 ± 2.4 MPa for treated fibers).

Regional heat capacity change is calculated from the ratio between the addition or subtraction of heat (ΔQ) with the increase or decrease in temperature (ΔT) region. The purpose of this study is to calculate the regional heat capacity change due to the changes of land cover composition with forest, shrubs, oil palm plantation and bare soil using Landsat-5 TM satellite data on 1994, 2000 and 2010. Total area that used on ​​this study is 12971 ha. In 1994-2000, 4 % of forest area and 2% shrubs were increased, followed by additional of biomass forest 4.01 tons/ha and 2.83 tons/ha for shrubs. The increased of forest area and biomass (tons/ha) caused by forest and shrubs growth processing towards climax that added the canopy volume. So that, the regional heat capacity in 1994 amounted 19384 MJC^o-1 increased to 19929 MJC^o-1 in 2000. Data observation for 2000-2010 showed that forest area decreased by 66% due to forest’s clearing into oil palm plantations (47%), shrubs (8%) and bare soil (11%). But, plant’s biomass continue to increased, i.e 1.48 ton/ha for forest, 2.73 tons/ha for shrubs and 4.63 tons/ha for bare soil. Before 2000, there was no land cover by oil palm plantations, so the increasing rate from this land was the biggest than the three other lands, amounting to 122.29 tons/ha. Decreasing in the percentage of forest area does not cause a decrease in the heat capacity of the region. Intensive maintenance on oil plam plantation such as water management, fertilizer and planting space made it biomass productivity and ability to save the heat is greater than the forest. As the result, in 2010 regional heat capacity increased to 22508 MJC^o-1.

We report magnetic silver nanoshells (M AgNSs) that have both magnetic and SERS properties for SERS-based detection. The M AgNSs are composed of hundreds of Fe3O4 nanoparticles for rapid accumulation and bumpy silver shell for sensitive SERS detection by near-infrared laser excitation. The intensity of the SERS signal from the M AgNSs was strong enough to provide single particle-level detection. We obtained much stronger SERS signal intensity from the aggregated M AgNSs than from the non-aggregated AgNSs. 4-Fluorothiophenol was detected at concentrations as low as 1 nM, which corresponds to 0.16 ppb. The limit of detection for tetramethylthiuram disulfide was 10 μM, which corresponds to 3 ppm. The M AgNSs can be used to detect trace amounts of organic molecules using a portable Raman system.

A simple and effective surface modification of polyester fabrics with sulfuric acid to improve the interfacial deposition of polypyrrole was presented in our work. A range of sulfuric acid concentrations were analyzed by studying water contact angle. Effect of sulfuric acid modification on the deposition of polypyrrole was investigated by sheet resistance and color depth of fabric samples. Polyester fabrics coated with polypyrrole layer were confirmed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-Ray diffraction spectra (XRD), Fourier transform infrared spectroscopy (FTIR). XPS showed that sulphur containing functional groups were obviously appeared on the polyester fiber surface after modification, which were advantageous to promote the deposition of polypyrrole onto polyester fabrics. The improved deposition increased electrical conductivity of fabric samples.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for 15-5PH Stainless steel by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as concentration of cutting fluid , temperature of cutting fluid , feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error and material removal rate, the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, concentration of cutting fluid, radial depth of cut and temperature of cutting fluid. Finally, confirmation tests were carried out to make a comparison between the experimental results and developed model. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

Background: The efficacy of sunscreen is evaluated by SPF values, which are quantitatively determined in laboratories on the backs of human subjects according to a standardized procedure. However, SPF cannot be directly translated to sunburn protection under real-life situations because actual efficacy depends on various factors related to human behaviors and environmental conditions. This study clinically evaluated the efficacy of two sunscreen sprays (SPF 30 and SPF 70) under natural sunlight exposure on healthy subjects at the beach. Methods: Twenty subjects were divided into two cells for the two sunscreen sprays (SPF 70 and SPF 30) in a single-center, actual usage test. The primary endpoint of the study was sunburn protection on the dorsal arms and the secondary endpoint was protection on the face and neck. Subjects stayed at the beach for 4 h after application of the sunscreens with normal beach activities. Subjects’ behavior at the beach, the amounts of sunscreen applied and reapplied, and environmental conditions were all recorded. Results: There was no significant sunburn for a majority of the subjects in either cell. However, neither sunscreen completely blocked the sunburn, especially for the face/neck area. We found that the SPF 70 sunscreen was more effective than the SPF 30 sunscreen. Conclusion: Modern sunscreen sprays, applied liberally, are effective in providing sunburn protection for the body in a beach setting.

The urbanization effects on land surface phenology (LSP) have been investigated by many studies, but few studies focused on the temporal variations of urbanization effects on LSP. In this study, we used the MODIS EVI, MODIS LST data and China’s Land Use/Cover Datasets (CLUDs) to investigate the temporal variations of urban heat island intensity and urbanization effects on LSP in Northeast China during 2001–2015. Land surface temperature (LST) and phenology differences between urban and rural areas represented the urban heat island intensity and urbanization effects on LSP, respectively. Mann-kendall nonparametric test and Sen's slope were used to evaluating the trends of urbanization effects on LSP and urban heat island intensity. The results indicated that the average land surface phenology (LSP) during 2001–2015 was characterized by high spatial heterogeneity. The start of the growing season (SOS) in old urban area had become earlier and earlier than rural area and the differences of SOS between urbanized area and the rural area changed greatly during 2001–2015 (−0.79 days/year, p < 0.01). Meanwhile, the length of the growing season (LOS) in urban and adjacent areas had become increasingly longer than rural area especially in urbanized area (0.92 days/year, p < 0.01), but the differences of the end of the growing season (EOS) between urban and adjacent areas did not change significantly. Next, the UHII increased in spring and autumn during the whole study period. Moreover, the correlation analysis indicated that the increasing urban heat island intensity in spring contributed greatly to the increases of urbanization effects on SOS, but the increasing urban heat island intensity in autumn did not lead to the increases of urbanization effects on EOS in Northeast China.

Piezoelectric nanotransducers may offer key advantages in comparison with conventional piezoelectrics, including more choices for types of mechanical input, positions of the contacts, dimensionalities and shapes. However, since piezo-semiconductive nanostructures are generally much easier to fabricate and integrate into functional systems than insulating materials, modeling becomes significantly more intricate and the effects of free charges have been considered only in a few studies. The available reports are complicated by the absence of proper nomenclature and figures of merit. Besides, some analyses are incomplete. For instance, the local piezopotential and free charges within axially strained conical piezo-semiconductive nanowires have only been systematically investigated for very low doping (1016 cm-3) and under compression. Here we give the definitions for the enhancement, depletion, base and tip piezopotentials, their characteristic lengths and both the tip-to-base and the depletion-to-enhancement piezopotential-ratios. As an example, we use these definitions for analyzing the local piezopotential and free charges in n-type ZnO truncated conical nanostructures with different doping levels (intrinsic, 1016 cm-3, 1017 cm-3) for both axial compression and traction. The definitions and concepts presented here may offer insight for designing high performance piezosemiconductive nanotransducers.

Visualization of volumetric data holds great importance, particularly in medical and biomedical applications. Various imaging techniques, such as FMRI and 3D microscopy, are employed to generate volumetric data, used in medical practice, research, and teaching. Commonly utilized tools like 3D Slicer, Fiji, and MATLAB ® aid in rendering and analyzing 3D images. However, these tools may lack comprehensive rendering functionality and face challenges in handling computational demands as data sizes grow. To address these limitations, this work introduces a GPU-supported renderer with a MATLAB ® interface. This solution gives the user flexible control over rendering parameters and optimizes data transfer through a memory management system. By leveraging the computational power of NVIDIA GPUs, the renderer enables complex and high-quality renderings, enhancing speed and efficiency. It therefore facilitates the analysis and visualization of volumetric data within an integrated environment, namely MATLAB ®, streamlining their workflows. This advancement provides valuable opportunities for researchers and medical professionals to explore and comprehend volumetric data effectively.

Despite being small and simple structured in comparison to their victims, virus particles have the potential to harm severly and even kill highly developed species such as humans. To face upcoming virus pandemics, detailed quantitative biophysical understanding of intracellular virus replication mechanisms is inevitable. Unveiling the relationship of form and function might allow to determine putative attack points relevant for the systematic development of direct antiviral agents (DAA) and potent vaccines. Biophysical investigations of spatio-temporal dynamics of intracellular virus replication so far are rare. We are developing a framework to allow for fully spatio-temporal resolved virus replication dynamics simulations based on partial differential equations models (PDE) and evaluated with advanced numerical mathematical methods on leading supercomputers. This study presents an advanced highly nonlinear model of the genome replication cycle of a specific RNA virus, the Hepatitis C virus (HCV). The diffusion-reaction model mimics the interplay of the major components of the viral RNA (vRNA) cycle, namely non structural viral proteins (NSP), vRNA and a generic host factor. Technically, we couple surface PDEs (sufPDEs) on the 3D embedded 2D Endoplasmatic Reticulum (ER) manifold with PDEs in the 3D membranous web (MW) and cytosol volume. (The MWs are the replication factories growing on the ER induced by NSPs.) The sufPDE/PDE model is evaluated at realistic reconstructed cell geometries which are based on experimental data. The simulations couple the effects of NSPs which are restricted to the ER surface with effects appearing in the volume. The volume effects include the host factor supply from the cytosol and the MW dynamics. Special emphasis is put to the exchange of components between ER surface, MWs and cytosol volume. As the vRNA spatial properties are not fully understood so far in experiment, the model allows for vRNA both restricted to the ER and moving in the cytosol. The visualization of the simulation resembles a look into some sort of fully 3D resolved “in silico microscopes” to mirror and complement in vitro / in vivo experiments for the intracellular vRNA cycle dynamics. The output data are quantitatively consistent with experimental data and provoke advanced experimental studies to validate the model.

In this paper, we present the extension of the pressure-based solver designed for the simulation of compressible and/or incompressible two-phase flows of viscous fluids. The core of the numerical scheme is based on the hybrid Kurganov— Noele — Petrova/PIMPLE algorithm. The governing equations are discretized in the conservative form and solved for velocity and pressure, with the density evaluated by an equation of state. The acoustic-conservative interface discretization technique helps to prevent the unphysical instabilities on the interface. The solver was validated on various cases in wide range of Mach number, both for single-phase and two-phase flows. The numerical algorithm was implemented on the basis of the well-known open-source Computational Fluid Dynamics library OpenFOAM in the solver called interTwoPhaseCentralFoam. The source code and the pack of test cases are available on GitHub: https://github.com/unicfdlab/hybridCentralSolvers

In this article, the research team has systematically developed a method to model the kinematics and dynamics of a 3-wheeled robot subjected to external disturbances and sideways wheel sliding. These models will be used to design control laws that compensate for wheel slippage, model uncertainties, and external disturbances. These are control algorithms developed based on Dynamic Surface Control (DSC). Adaptive trajectory tracking DSC algorithm using fuzzy logic system (AFDSC) and radial neural network (RBFNN) with fuzzy logic system to overcome the disadvantages of DSC and expand the application domain for wheeled Mobile Robots (WMR). However, this Adaptive Fuzzy Neural Network Dynamic Surface Control (AFNNDSC) adaptive controller ensures the closed system is stable and follows the preset trajectory in the presence of wheel slippage model uncertainty and is affected by significant amplitude disturbances. The stability and convergence of the closed-loop system are guaranteed based on the Lyapunov analysis. The AFNNDSC adaptive controller is evaluated by simulation on MATLAB/Simulink software and in a steady state. The maximum position error on the right wheel and left wheel is 0.000572 (m) and 0.000523 (m), and the angular velocity tracking error in the right and left wheels of the control method is 0.000394 (rad/s). The experimental results show the correctness of the theoretical analysis, the effectiveness of the proposed controller, and the possibility of practical application.

Rapid and extensive urbanization has adversely impacted humans and ecological entities in the recent decades through a decrease in surface permeability and the emergence of urban heat islands (UHI). While detailed and continuous assessments of surface permeability and UHI are crucial for urban planning and management of landuse zones, they have mostly involved time consuming and expensive field studies, and single sensor derived large scale aerial and satellite imageries. We demonstrated the advantage of fusing imageries from multiple sensors for landuse and landcover (LULC) change assessments as well as for assessing surface permeability and UHI emergence in Tirunelveli, Tamilnadu, India. Cartosat-2 and Landsat-7 ETM+ imageries from 2007 and 2017 were fused and classified using a Rotation Forest (RF), while surface permeability and temperature were quantified using Soil-Adjusted Vegetation Index (SAVI) and Land Surface Temperature (LST) index, respectively. Fused images exhibited higher classification accuracies than non-fused images, i.e. overall kappa coefficient values 0.83 and 0.75, respectively. We observed an overall increase of 20 km2 (45%) in the coverage of urban (dry, real estate plots and built-up) areas, while a decrease of 27 km2 (37%) for vegetated (cropland and forest) areas in Tirunelveli between 2007 and 2017. The SAVI values indicated an extensive decrease in surface permeability for Tirunelveli overall (0.4) and also for almost all LULC zones. The LST values exhibited an associated overall increase (1.30C) of surface temperature in Tirunelveli with the highest increase (2.40C) for urban built-up areas between 2007 and 2017. The SAVI-LST combined metric depicted the Southeastern built-up areas in Tirunelveli as a potential UHI hotspot, while a caution for the Western riparian zone for UHI emergence in 2017. Our results provide important metrics for surface permeability and UHI monitoring, and inform urban and zonal planning authorities about the advantages of satellite image fusion.

Introduction: Rural Americans face significant health disparities due to limited access to healthcare services. Telehealth has emerged as a promising solution to mitigate these disparities by facilitating remote access to medical care. This paper comprehensively reviews the advantages, challenges, and implementation strategies of telehealth in rural areas.Method: A narrative review methodology was employed to synthesize existing literature and case studies on telehealth in rural settings. Databases such as PubMed, Google Scholar, and JSTOR were searched for relevant studies published in the last three decades. Keywords such as "telehealth," "rural health," and "healthcare disparities" guided the search process. The review focused on studies assessing the impact of telehealth on healthcare access, cost-effectiveness, and quality of care in rural areas.Results: The review findings indicate that telehealth significantly enhances healthcare access by reducing travel distances, increasing availability of specialist consultations, and promoting patient engagement. It improves chronic disease management and patient satisfaction by enabling convenient access to healthcare services at home. Despite initial setup costs and challenges such as broadband access and regulatory issues, telehealth demonstrates long-term cost savings through reduced travel expenses and improved healthcare efficiency. Quality of care is enhanced through improved communication between healthcare providers and patients, leading to better treatment adherence and health outcomes.Conclusion: Telehealth represents a transformative approach to address healthcare disparities in rural areas. It offers a cost-effective solution to improve access to healthcare services, enhance patient outcomes, and reduce healthcare costs in the long run. However, successful implementation requires addressing infrastructure challenges, refining reimbursement policies, and ensuring regulatory support. Future efforts should focus on expanding broadband infrastructure, refining policy frameworks, and conducting further research to optimize telehealth's impact on rural healthcare delivery.

Computational neuroscience has undergone a significant transformation in recent years, driven by the exponential growth of neural data and advancements in data science and machine learning. While traditional theoretical models remain valuable, there is a growing emphasis on integrating data-driven approaches to develop more accurate, biologically plausible, and predictive models of neural function. This shift has led to a new equilibrium in the field, where data-driven model development, machine learning techniques, and hybrid approaches that combine data and theory are increasingly prevalent. In this article, we discuss the evolving landscape of computational neuroscience, highlighting the importance of data-driven methods and the emergence of a more integrative approach that leverages both data and theory to unlock the mysteries of the brain. We also explore the implications of this shift for future research and clinical applications, emphasizing the potential for data-driven computational neuroscience to revolutionize our understanding of neural function and pave the way for new treatments for neurological disorders.

This research presents a novel algorithmic implementation to improve the analysis of visually controlled interception and accompanying motor action through the computational application of harmonic ratios and stimulation invariants. Unlike traditional models that focus mainly on psychological aspects, our approach integrates the relevant constructs into a practical mathematical framework. This allows for dynamic prediction of interception points with improved accuracy and real-time perception-action capabilities, essential for applications in neurorehabilitation and virtual reality. Our methodology uses stimulation invariants as key parameters within a mathematical model to quantitatively predict and improve interception outcomes. The results demonstrate the superior performance of our algorithms over conventional methods, confirming their potential for ad-vancing robotic vision systems and adaptive virtual environments. By translating complex theo-ries of visual perception into algorithmic solutions, this study provides innovative ways to im-prove motion perception and interactive systems. This study aims to articulate the complex inter-play of geometry, perception, and technology in understanding and utilizing cross-ratios at infin-ity, emphasizing their practical applications in virtual and augmented reality settings.

Developing countries, including Small Island Developing States (SIDS) and Least Developed Countries (LDCs), are exceptionally vulnerable to climate change due to their distinct geographical and environmental characteristics. The impacts of climate change extend across their ecosystems, water resources, and vital economic sectors, such as food systems, health, education, and energy. Escalating sea levels and heightened salinity levels imperil freshwater reserves, while warmer ocean temperatures and acidification disrupt water demand, tourism, health services, and fisheries. Furthermore, developing countries bear the brunt of water shortages, flooding, and deteriorating water quality. Alarmingly, nearly two-thirds of the global population experience severe water scarcity for at least one month annually, with the majority residing in developing countries. By 2025, half of the world's population could inhabit areas grappling with water scarcity, predominantly concentrated in developing nations. In this context, innovative adaptation strategies, notably transformative wastewater projects, are imperative for fostering sustainability and resilience in these regions. However, significant barriers impede progress, creating a stark disparity between current financing capabilities and the imperative to fund water security initiatives. Compounding these challenges, developing countries find themselves ensnared in a burgeoning debt crisis, marked by escalating interest rates and inflation, which threatens to impede developmental progress and curtail investments in adaptation and mitigation endeavors. Consequently, there arises a critical necessity to harness innovative financial mechanisms to transform these debts into assets that facilitate climate action. This paper meticulously explores the potential of debt-for-climate swaps as a catalyst for advancing transformative wastewater projects, with a focused lens on their strategic deployment to underpin critical initiatives. Through rigorous examination of case studies and empirical evidence, the paper elucidates how debt-for-climate swaps can effectively bolster sustainable wastewater management systems in developing countries. Furthermore, it delineates best practices for leveraging these mechanisms to fortify environmental sustainability and resilience. Additionally, the paper delineates the roles and responsibilities of key stakeholders, including governments, policymakers, the private sector, communities, and climate financial institutions. By amalgamating theoretical insights with tangible examples, this paper furnishes a comprehensive framework for harnessing debt-for-climate swaps to enhance water security and resilience in developing countries. It endeavors to furnish actionable strategies for policymakers, practitioners, and stakeholders to navigate the complex terrain of climate change and engender sustainable development.

Background. Escherichia coli commonly causes catheter-related bloodstream infection (C-RBSI) in specific populations. The differential time to positivity (DTTP) technique is the recommended conservative procedure for diagnosing C-RBSIs. Methods. We conducted a retrospective study of episodes in which E. coli was isolated from catheter lumens obtained using the DTTP technique. We analysed microbiological and clinical data based on the DTTP technique as either catheter colonization, C-RBSI, or non-C-RBSI. Results. We included 89 catheter blood cultures classified as follows: catheter colonization, 33.7%; C-RSBI, 9.0%; and non-C-RBSI, 57,3%. Catheter withdrawal was 15.7% without positive catheter-tip cultures. We found no statistically significant differences in catheter type, antibiotic treatment, or clinical outcome among groups, except for the frequency of catheter lock therapy or in the frequency of successful treatment. Mortality was associated with C-RBSI in only 1 patient. Conclusion. E. coli bacteremia diagnosed by the DTTP technique was non-catheter related in most patients. As the majority of the catheters were retained, E. coli bacteremia could not be microbiologically confirmed or ruled out as catheter related by catheter-tip culture. Future studies are needed to assess the profitability of the DTTP technique for diagnosing E. coli C-RBSIs..

This retrospective study examines 248 test-bolus examinations preceding contrast-enhanced magnetic resonance angiography (CE-MRA) to extract clinically relevant data for critical limb ischemia (CLI) management. Methods involved a retrospective review of test-bolus exams, analysing 60 graphs for time-to-peak (TTP), full-width half-maximum (FWHM) time, and time to continual rise in signal intensity. These values were correlated with heart function parameters (ejection fraction, ASA-Classification, Lee-Index, and MET-Score). Results indicate a mean TTP of 31.2 ± 7.3s, showing a correlation between ejection fraction and ASA classification. Patients with atrial fibrillation exhibited prolonged TTP compared to those without. Despite population heterogeneity, findings facilitate risk stratification for limb-saving interventions in CLI. TTP emerges as a potential clinical cardiovascular parameter and a risk factor for vascular interventions. Given the variation in injection protocols across centres, this study underscores the importance of precise bolus arrival time documentation for future multicentre studies.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

Silicon Photomultipliers find applications across various fields. One potential Silicon Photomultiplier application domain is neutrino telescopes, where they may enhance the angular resolution. However, the elevated dark count rate associated with Silicon Photomultipliers represents a significant challenge to their widespread utilization. To address this issue, it is proposed to use Silicon Photomultipliers and Photomultiplier Tubes together. The Photomultiplier Tubes signals would serve as a trigger to mitigate the dark count rate, thereby preventing undue saturation of the available bandwidth. This paper presents an investigation into a fast and resource-efficient method for filtering Silicon Photomultiplier dark count rate. A low-resource and fast coincident filter has been developed, which removes the Silicon Photomultiplier dark count rate by using as trigger the Photomultiplier Tube input signals. The architecture of the coincidence filter, together with the first results obtained, which validate the effectiveness of this method are presented.

There are two generic approaches to curing any medical condition. The first treats every patient for all of the known possible causes that contribute to pathogenesis; the second individualizes potentially curative therapy by identifying in each separate patient only those components of pathogenesis that are actually operative, and treating those. This article adopts the second approach for formulating a cure of Alzheimer’s dementia (AD). Components of AD’s pathogenesis are, in alphabetical order: circadian rhythm disturbances, depression, diabetes and insulin resistance, dyslipidemia, hypertension, inflammation, metabolic syndrome, mitochondrial dysfunction, nutritional deficiencies, TGF-β deficiency, underweight, vascular abnormalities, and Wnt/β-catenin deficiency. For each component, data are described that show the degree by which its prevalence is more in the patients with mild cognitive impairment (MCI) who did not revert to having normal cognition than in those who did, because the former group is the pool of patients from among which future AD may develop. Addressing only those components that are present in a particular individual, is potentially a curative strategy. Published data indicate that curative therapy requires that the number of such components to address should be ≥3. Although structural brain changes cannot be directly addressed, the impaired neural tracts result from many of the reversible causal elements, so correcting them will benefit those tract

It is unavoidable that the characteristics of the robot system alter inexactly or cannot be correctly determined during movement and are impacted by external disturbances. There are many adaptive control methods, such as sliding control or neural control, to improve the quality of trajectory tracking for robot motion systems. Still, those methods require a large amount of computation related to solving the problem of constrained nonlinear optimization problem. The article presents some techniques for determining an intelligent controller's online learning function parameters, including two circuits: the inner circuit is a state feedback linearized controller, and the outer course is an Interactive learning controller and does not use the robot's mathematical mode with function parameters online optimal learning and intelligent online learning closely following the joint model to stabilize the robot system. Finally, the 2-DOF planar robot simulation is performed on Matlab software R2022b. The findings indicate that outstanding tracking performance is achievable.

Inverse optimal control is a method for recovering the cost function used in an optimal control problem in expert demonstrations. Most studies on inverse optimal control have focused on building the unknown cost function through the linear combination of given features with unknown cost weights, which are generally considered to be constant. However, in many real-world applications, the cost weights may vary over time. In this study, we propose an adaptive online inverse optimal control approach based on a neural-network approximation to address the challenge of recovering time-varying cost weights. We conduct a well-posedness analysis of the problem and suggest a condition for the adaptive goal, under which the weights of the neural network generated to achieve this adaptive goal are unique to the corresponding inverse optimal control problem. Furthermore, we propose an updating law for the weights of the neural network to ensure the stability of the convergence of the solutions. Finally, simulation results for an example linear system are presented to demonstrate the effectiveness of the proposed strategy. The proposed method is applicable to a wide range of problems requiring real-time inverse optimal control calculations

People are drawn to woodcut-style designs due to their striking visual impact and strong contrast. However, traditional woodcut prints and previous computer-aided methods have not addressed the issues of dwindling design inspiration, lengthy production times, and complex adjustment procedures. We propose a novel network framework, the Woodcut-style Design Assistant Network (WDANet), to tackle these challenges. Notably, our research is the first to utilize diffusion models to streamline the woodcut-style design process. We've curated the Woodcut-62 dataset, featuring works from 62 renowned historical artists, to train WDANet in absorbing and learning the aesthetic nuances of woodcut prints, offering users a wealth of design references. Based on a noise reduction network, our dual cross-attention mechanism effectively integrates text and woodcut-style image features. This allows users to input or slightly modify a text description to quickly generate accurate, high-quality woodcut-style designs, saving time and offering flexibility. As confirmed by user studies, quantitative and qualitative analyses show that WDANet outperforms the current state-of-the-art in generating woodcut-style images and proves its value as a design aid.

Natural gas plays a significant role in Tunisia's energy mix. Tunisia imports 66% of natural gas (NG) from Algeria (ANG), and the rest is provided by local gas fields mainly Miskar gas (MNG). To counteract this deficit, the Power-to-Gas approach emerges as a promising solution, given Tunisia's abundant renewable energy resources. By blending green hydrogen into the NG network, it is possible to (i) address the current energy crisis, (ii) lower the carbon intensity of the gas grid, and (iii) encourage sector coupling through the use of various renewable energy sources. This study presents an overview of various interchangeability indicators and investigates accordingly the allowable ratios for hydrogen blending with two types of natural gas distributed in Tunisia (ANG and MNG). It also explores the impact of hydrogen injection on the energy content variation and various combustion parameters. The results confirm that both ANG and MNG can withstand a maximum hydrogen blend of up to 20%. The article concludes with recommendations for further experimental testing of the findings and emphasizes the need to look into infrastructure and safety requirements with regards to the Natural gas network in Tunisia. This research serves as a critical step towards harnessing the potential of green hydrogen in Tunisia.

This paper delves into the essential role of local communities in mitigating climate change in the post-pandemic landscape, with a specific focus on Barangay Acmac, Iligan City, Philippines. Employing a qualitative research approach, the study integrates in-depth literature reviews, informal interviews with participants (B-Part 1 to B-Part 20), meticulous observations, and thematic analysis. The research has uncovered crucial insights, including variations in community climate change awareness that emphasize the necessity of comprehensive education and awareness campaigns. It highlights the significance of community-driven initiatives, adaptation, and resilience as key elements in addressing climate change. Collaborative efforts between local government officials and the community are showcased as effective instruments of climate change mitigation, yet challenges persist, including addressing the perceived powerlessness of some community members. The methodology, participants, and theoretical framework offer a robust foundation for exploring community responses to climate change. Drawing from a diverse theoretical framework, this study presents a comprehensive understanding of the climate change and pandemic intersection. The findings firmly establish that local communities are pivotal players in the global endeavor to mitigate climate change, underscoring the need for collective action, extensive education, and shared responsibility. The post-pandemic era presents a unique opportunity for local communities, policymakers, barangay officials, and residents to champion climate education, foster community-driven initiatives, and empower individuals to enact change at the grassroots level. The collaborative spirit observed in Barangay Acmac in 2022 serves as a model for communities worldwide, offering a blueprint for addressing similar challenges. Overall, this paper concludes with a resounding call to action, advocating for the recognition of local communities as the driving force in climate change mitigation, stressing that the power to combat climate change resides within these communities. The time for action is now, and local communities are the catalysts of this essential mission.

The aim of this article is to review hydrogen combustion applications within the energy transition framework. Hydrogen blends are also included, from the well known hydrogen enriched natural gas (HENG) to the hydrogen and ammonia blends whose chemical kinetics is still not clearly defined. Hydrogen and hydrogen blends combustion characteristics will be firstly summarized, in terms of standard properties like the laminar flame speed and the adiabatic flame temperature, but also evidencing the critical role of hydrogen preferential diffusion in burning rate enhancement and the drastic reduction in radiative emission with respect to natural gas flames. Then, combustion applications in both thermo-electric power generation (based on internal combustion engines, i.e., gas turbines and piston engines) and hard-to-abate industry (requiring high temperature kilns and furnaces) sectors will be considered, highlighting the main issues due to hydrogen addition related to safety, pollutant emissions, and potentially negative effects on industrial products (e.g., glass, cement and ceramic).

This paper offers a set of comprehensive guidelines aimed at facilitating the widespread adoption of hydrogen in the industrial hard-to-abate sectors. The authors begin by conducting a detailed analysis of these sectors, providing an overview of their unique characteristics and challenges. The paper delves into specific elements related to hydrogen technologies, shedding light on their potential applications and discussing feasible implementation strategies. By exploring the strengths and limitations of each technology, the paper offers valuable insights into its suitability for specific applications. Finally, through a particular analysis focused on the steel sector, the authors provide in-depth information on the potential benefits and challenges associated with hydrogen adoption in this particular context. By emphasizing the steel sector as a focal point, the authors contribute to a more nuanced understanding of hydrogen's role in decarbonizing industrial processes and inspire further exploration of its applications in other challenging sectors.

Higher salt (sodium) intake has been associated with a higher blood pressure (BP). The association degree may be influenced by factors such as age, origin and dietary components. This study aimed to evaluate the 24-hours urinary sodium (Na) and potassium (K) excretion in normotensive and hypertensive Dominicans adults and estimate their salt intake. 163 volunteers (18-45, 46-80 years) participated in a cross-sectional study. 24-hours Na and K urinary excretion were measured using an ion selective electrode technique. Na and K urinary excretion (99.4±46.5 and 35.0±17.5 mmol/24h) did not correlated with BP, except in the normotensive group in which K correlated with SBP (0.249, p=0.019). Na and K excretion were similar for normo- and hypertensive subjects. Na-to-K molar ratio (3.1±1.3) was higher in younger subjects (p=0.040). Na-to-K ratio was associated with DBP in the total group (r=0.153, p=0.052), in the hypertensive group (r=0.395, p<0.001) and in the older group with SBP (0.350, p=0.002) and DBP (0.373, p<0.001). In the older group, Na-to-K ratio and DBP correlated after controlling for subjects with hypertension controlled by treatment (r=0.236, p=0.041). The Na-to-K ratio correlated, when salt intake was over 5g/d (52.2%), with SBP (rho=0.219, p=0.044) and DBP (rho=0.259, p=0.017). Determinants of BP were age-dependent and in younger subjects were: sex (SBP, beta: 14.02±2.87, p<0.001) and body mass index (BMI) (beta:-12.07±3.72, p=0.001, beta:9.44±2.87, p=0.001, for SBP and DBP, respectively) and, in the olders, the Na-to-K ratio, for SBP (beta:6.7±2.4, p=0.005) and DBP (beta:3.8±1.1, p<0.001). The mean Na and salt intakes (2.3 and 5.8 g/d) were slightly higher and K intake lower (1.4 g/d) than WHO recommendations.

The basic constitutional freedoms and rights of a person and citizen are in principle unlimited: the full scope of their exercise is the rule, and the restriction determined by law can only be an exception based on explicit constitutional authority and the legitimate aim of the restriction determined by the Constitution. That being so, the restrictions - in addition to being based on constitutional authority and pursuing constitutional objectives - should be commensurate with the needs to achieve these objectives. This means that restrictive legal rules must be suitable for achieving the legitimate aim pursued, must not be stricter than necessary and must be balanced between the constitutionally guaranteed subjective right of the individual and the interests of society. In this scholar paper, the authors point out the economic and legal consequences of the violation of individual privacy and data protection rights caused by the public disclosure of personal data of people who, at a certain time, were obliged to self-isolate due to suspicion of Covid-19 virus infection.

One of the models that could be used to understand the adoption of vaccine uptake is the Health Belief Model (HBM). The aim of this study is to assess the role of HBM constructs and perceived health status (PHS) on vaccination status of individuals and to understand the role of socio-demographic variables on HBM scoring. A comparative cross-sectional telephone survey was conducted among 1,325 vaccinated (60.0%) and non-vaccinated (40.0%) vaccinated individuals aged 40 years and above in July 2021 in Punjab province, Pakistan. A higher level of education was the strongest predictor of positive HBM. All constructs of HBM, PHS and cues-to-action were significant predictors of COVID-19 vaccination uptake with perceived benefits as the strongest predictor. In order to expand the vaccination coverage, doubled pronged interventions utilizing both ICT and human resources should be designed that address each barrier perceived by individuals and understandably communicate the benefits of COVID-19 vaccine to the broader population.

The effects of transcranial magnetic stimulations (TMS) show that the human brain is impacted by some magnetic fields (EMFs). Moreover, after a delay, it produces potentials that reveal a subsequent processing of this impact. The human brain might also be sensitive to very weak magnetic fields of extremely low frequencies (vwEMFelf). Namely, to the vwEMelf produced by the brain of other persons when they process visual stimuli. In effect, two studies report that the event-related brain potentials (ERPs) that are evoked by presenting a picture to a participant can be modulated by simultaneously presenting a picture to a partner. To confirm it here, we followed most of the methods of these studies. We recorded the ERPs evoked by presenting, at each trial, the photograph of a face. Simultaneously and, most importantly, privately, we presented a partner with the same or with a different face photograph. ERPs of participants were found to depend on that sameness (p0.001), unbeknownst to them. These joint processing effects (JPEs), confirm a sensitivity of the human brain to the vwEMFelf produced by other brains.

A major challenge in the clinical management of patients with mesial temporal lobe epilepsy (MTLE) is identifying those who do not respond to antiseizure medication (ASM), allowing for the timely pursuit of alternative treatments, such as epilepsy surgery. Here, we investigated changes in plasma metabolites as biomarkers of pharmacoresistance in patients with MTLE. Furthermore, we used the metabolomics data to gain insights into the mechanisms underlying MTLE and response to ASM. We performed an untargeted metabolomic method using magnetic resonance spectroscopy and multi- and univariate statistical analyses to compare data obtained from plasma samples of 28 patients with MTLE compared to 28 controls. The patients were further divided according to response to ASM: 20 patients were refractory to treatment, and eight were responsive to ASM. We only included patients using carbamazepine in combination with clobazam. We compared the group of patients with controls and found that the profiles of glucose (p = 0.01), saturated lipids (p = 0.0002), isoleucine (p = 0.0001), β-hydroxybutyrate (p = 0.0003), and proline (p = 0.02) were different in patients compared to controls (p &lt; 0.05). In addition, lipoproteins (p = 0.05), lactate (p = 0.05), glucose (p = 0.05), unsaturated lipids (p = 0.05), isoleucine (p = 0.05), and proline (p = 0.05), could discriminate between the two groups of patients classified according to response to ASM. The identified metabolites were linked to different biological pathways related to cell energy metabolism, and pathways linked to inflammatory processes and the modulation of neurotransmitter release and activity in MTLE. In contrast, we found that pyruvate metabolism may be linked to resistance to ASM. In conclusion, in addition to insights into the mechanisms underlying MTLE and the response to treatment with ASM, our results suggest that plasma metabolites may be used as biomarkers of disease and response to ASM in patients with MTLE. These findings warrant further studies exploring the clinical use of metabolites to assist in decision-making when treating patients with MTLE.

We describe a method for protein quantification and for mRNA quantification in small sample quantities of human induced pluripotent stem-cell-derived-cardiomyocytes (hiPSC-CMs). Demonstrated here is how the capillary-based protein detection system Wes^TM by ProteinSimple and the Power SYBR^TM Green Cells-to-CT^TM Kit by Invitrogen can be applied to individual samples in a 96-well microplate format and thus made compatible with high-throughput (HT) cardiomyocyte assays. As an example of the usage, we illustrate that Cx43 protein and GJA1 mRNA levels in hiPSC-CMs are enhanced when the optogenetic actuator, channelrodopsin-2 (ChR2), is genetically expressed in them. Instructions are presented for cell culture and lysate preparations from hiPSC-CMs, along with optimized parameter settings and experimental protocol steps. Strategies to optimize primary antibody concentrations as well as ways for signal normalization are discussed, i.e. antibody multiplexing and total protein assay. The sensitivity of both the Wes and Cells-to-CT kit enables protein and mRNA quantification in a HT format, which is important when dealing with precious small samples. In addition to being able to handle small cardiomyocyte samples, these streamlined and semi-automated processes enable quick mechanistic analysis.

Plants characterized by a soft or weak steam, such as climbing plants, need to find a potential support (e.g., wooden trunk) to reach greater light exposure. Since Darwin’s research on climbing plants, several studies on their searching and attachment behaviors have demonstrated their unique ability to process different support features to modulate their movements accordingly. Nevertheless, the strategies underlying this ability are yet to be uncovered. The present research tries to fill this gap by investigating how the interaction between above- (i.e., stem, tendril, …) and belowground (i.e., the root system) plant organs influence the kinematics of the approach-to-grasp movement. With three-dimensional (3D) kinematical analysis, we characterized the movement of pea plants (Pisum sativum L.) towards a support with different thicknesses above and belowground (i.e., thin below, thick aboveground, or the opposite). As a control condition, the plants were presented to supports with the same thickness below- and aboveground (i.e., either entirely thin or thick). The results suggest an integration between the information from below- and aboveground for driving the reach-to-grasp behavior of the aerial plant organs. Information about the support conveyed by the root system seems particularly important to fulfil the end-goal of the movement.

Both academic literature and global organizations have emphasized the need for responsible water consumption, as stated in the Sustainable Development Goal 12. However, individuals’ water-saving behaviors in their current state are not enough. This situation entails a resistance to change (RC) in consumer habits and a lack of perceived risk of scarcity. The novelty of this study lies in examining the influence of RC (through its emotional, cognitive, and confidence components) and perceived risk on water-saving intention. Interviews (n = 384) were conducted in the southeast Mediterranean area of Spain by interviewers using a paper-and-pencil questionnaire. The results of the structural equation modeling show that the perceived risk and the components of cognitive rigidity and negative emotions exert a direct influence on water-saving habits and an indirect influence on water-saving intention. None of the components of RC directly influence intention, and a lack of confidence in the outcomes of water saving does not influence water-saving habits or water-saving intention. In addition to the results obtained, the novelty of the work lies in the idea that in order to influence the perception of the risk of water scarcity through awareness campaigns, it is better to use an emotional message rather than showing facts or information, because this does not drive water saving behavior.

Peer-to-peer (P2P) energy trading – where energy prosumers transact directly between each other – could help enable transition to a low-carbon energy system. If it is to be supported in policy and regulation, it is important to anticipate the distributional impacts (or how it might impact segments of society differently). However, real-world evidence on P2P energy trading is currently extremely limited. To address this challenge in the short- to medium-term, this study aimed to explore what might be learned from the extensive body of research on a comparable offering in the accommodation sector: Airbnb. A realist review approach was employed to maximise transferability of findings, focused on what mechanisms are thought to lead to what distributional outcomes, in what contexts. On the basis of the review, participation in (and receipt of benefits of) P2P energy trading schemes would be expected to represent disproportionately those living in areas with network management challenges, who are younger and more highly educated. The review also raised the prospect of discrimination on the basis of characteristics such as race and gender where there are high levels of individual choice over who to trade with. Recommendations include monitoring, incentivising diversity, anonymization, and limiting trading choices.

High-performance motor drives that operate in harsh conditions require an accurate and robust angular position measurement to correctly estimate the speed and reduce the torque ripple produced by angular estimation error. For that reason, a resolver is used in motor drives as a position sensor due to its robustness. A resolver-to-digital converter (RDC) is an observer used to get the angular position from the resolver signals. Most RDCs are based on angle tracking observers (ATOs). On the other hand, generalized predictive control (GPC) has become a powerful tool in developing controllers and observers for industrial applications. However, no GPC-based RDC with zero steady-state error during constant speed operation was proposed. This paper proposes an RDC based on a second-order difference GPC (SOD-GPC). In SOD-GPC, the second-order difference operator is applied to design a GPC model with two embedded integrators. Thus, the SOD-GPC is used to design a type-II ATO whose steady-state angle estimation error tends to zero during constant speed operation. Simulation and experimental results prove that the proposed RDC system has better performance than other literature approaches.

The primary purpose of the study was the determination of the spatial day-to-day variability of extreme temperatures in Poland and the dependency of large temperature changes on atmospheric circulation in accordance with the Grosswetterlagen (GWL) classification. The goal was implemented based on data from 1966 to 2015, made available by the Institute of Meteorology and Water Management – National Research Institute. Day-to-day changes in maximum and minimum temperatures were designated with a rate of ≥ 6 °C (large) and with a rate of ≥ 12 °C (very large) and their spatial distribution was presented. Finally, the analysis of the dependency of considerable temperature changes on atmospheric circulation in accordance with the Grosswetterlagen (GWL) classification was conducted. The obtained results showed that in Poland in the period 1966-2015 the number of large changes in both Tmax and Tmin slightly increased, although the fluctuations show spatial variability. Large changes in Tmax occur more frequently in spring, and in Tmin in winter. Large changes in Tmax and Tmin are mainly recorded during cyclonic circulation, however, the anticyclonic circulation types favour especially large decreases in Tmin.

Over the past decade, wireless communication technologies have developed significantly for intelligent applications in road transport. This paper provides an overview of telecommunications-based intelligent transport systems with a focus on ensuring system safety and resilience. In vehicle-to-everything, these problems are extremely acute due to the specifics of the operation of transport networks, which requires the use of special protection mechanisms. In this regard, it was decided to use blockchain as a system platform to support the needs of transport systems for secure information exchange. This paper describes the technological aspects of implementing blockchain technology in vehicle-to-network; the features of such technology are presented, as well as the features of their interaction.

This study presents a new kinetic scheme for the mass yield prediction of waste lignocellulosic biomasses treated by Hydrothermal Carbonization (HTC). The proposed reactions are based on the decomposition, solubilization, and polymerization of each main fraction of the biomass: cellulose, hemicellulose, and lignin. The ash content was assumed to be inert. The kinetic parameters have been obtained by non-linear adjustment using a data set with 220 experimental runs collected from the literature. The results indicate that the pre-exponential factors range was from 7.33 x10¹ to 1.412x10⁵ min^-1, and activation energies were between 33.75 y 225.3 kJ/mol. A good fit is achieved between the observed and predicted data with an R² of 0.81 and an RMSE of 7.7 %. The proposed scheme was validated with the experimental data obtained by the HTC of sawdust (Pinus radiata) and rapeseed (Brassica napus). The experiments were carried out at temperatures of 190, 220, and 250 ºC and reaction times of 0, 30, 60, 90, and 120 min. The predicted values showed an average error of 2.3 and 3.5 %, respectively. Therefore, the kinetic scheme is a useful tool in the conversion analysis of waste biomass treated by HTC.

The tobacco epidemic is one of the leading public health threats the world has ever faced and public health policy that seeks to limit the problem may not only have to target the price of tobacco but also the initiation stage in a smoker’s life – the adolescent stage. This research contributes to the health economics literature by using a Bayesian hierarchical logistic model, estimated using Hamiltonian Monte Carlo (HMC) methods to empirically identify what drives the intentions to quit smoking among adolescent smokers in Zambia. Results suggest that among the junior secondary school-going adolescent smokers in Zambia, about 63% have plans to quit smoking. We find socio-demographic characteristics and several tobacco-smoking-related factors as the main drivers of adolescent smokers’ plans to quit smoking. Most importantly, we provide insights that could be useful to help adolescent smokers realize their quitting plans.

Background: Telemedicine (interconsultation between primary and hospital care teams) has been operating in the counties of Central Catalonia Bages, Moianès and Berguedà since 2011 in the specialties of teledermatology, teleulcers, teleeyelids and teleaudiometries. For the period until the end of 2019, a total of 52,198 visits have been recorded. Objective: To analyse the differential costs between telemedicine and usual care in a semi-urban environment. Methodology: A cost-minimization evaluation, including direct and indirect costs from a societal perspective, distinguishing healthcare and user’s costs, within a three-month period. Results: Telemedicine saved € 780,397 over the period analysed. A differential cost favourable to telemedicine of about € 15/visit has been observed, the patient being the largest beneficiary of this saving (by 85%) in terms of shorter waiting times and travel costs. From the healthcare system perspective, moving the time spent in a hospital care consultation to primary care is efficient in terms of the total time devoted per patient. In social terms and in this context, telemedicine is more efficient than usual care. Conclusion: Users’ saving of time in terms of consultation and travel is the main driver of interconsultation between primary and hospital care savings in a semi-urban context. The telemedicine service is also economically favourable for the healthcare system, enabling it to provide a more agile service, which also benefits the healthcare professionals.

This study used double-bounded dichotomous-choice to estimate and analyze the factors affecting households’ willingness to pay (WTP) for water quality improvement. This study notes that households with higher income, living near polluted water source, using tap water instead of natural water, who are handicraft producers, and who have more members are willing to pay more. However, households who rarely hear about environmental pollution issues and who are offered a higher bid are more likely to refuse to pay. Solutions to improve water quality are suggested such as to raise people's awareness through communication channels and social organizations; to increase income associated with environmental protection policies; to construct wastewater treatment plants; to encourage the relocation of production establishments to industrial parks and industrial complexes; to put regulations on collection, payment and sanctions in case of not declaring and paying fees into village conventions; to promulgate circulars, and bylaws to concretize and simplify regulations and policies of the Government, Ministry of Natural Resources and Environment.

Purpose: Localization and mapping with LiDAR data is a fundamental building block for autonomous vehicles. Though LiDAR point clouds can often encode the scene depth more accurate and steadier compared with visual information, laser-based Simultaneous Localization And Mapping (SLAM) remains challengeable as the data is usually sparse, density variable and less discriminative. The purpose of this paper is to propose an accurate and reliable laser-based SLAM solution. Design/methodology/approach: The method starts with constructing voxel grids based on the 3D input point cloud. These voxels are then classified into three types to indicate different physical objects according to the spatial distribution of the points contained in each voxel. A global environment model with Partition of Unity (POU) implicit surface is maintained along the process and located voxels are merged into it from stage to stage, through scan-to-model matching implemented by Levenberg-Marquardt method. Findings: We find a laser-based SLAM method. The method uses POU implicit surface representation to build the model and is evaluated on the KITTI odometry benchmark without loop closure. Experimental results indicate that the method achieves accuracy comparable to the state-of-the-art methods. Originality/value: We propose a novel, low-drift SLAM method, which falls into a scan-to-model matching paradigm, operates on point clouds obtained from Velodyne HDL64. The method is of value to researchers developing SLAM systems for autonomous vehicles.

Background: Although transcatheter arterial chemoembolisation (TACE) is the standard of care for intermediate-stage hepatocellular carcinoma (HCC), this is a largely heterogeneous disease that includes a subgroup of patients who do not benefit from TACE. The treatment strategy for this subgroup of patients currently remains an unmet need in clinical practice. Here, we performed a proof-of-concept study that lenvatinib may be more favourable treatment option over TACE as an initial treatment in intermediate-stage HCC patients with large or multinodular tumours exceeding the up-to-seven criteria. Methods: This proof-of-concept study included 642 consecutive patients with HCC initially treated with lenvatinib or conventional TACE (cTACE) between January 2006 and December 2018. Of these patients, 176 who received lenvatinib or cTACE as an initial treatment and met the eligibility criteria [unresectable, beyond the up-to-seven criteria, no prior TACE/systemic therapy, no vascular invasion, no extrahepatic spread and Child-Pugh A liver function] were selected for the study. Propensity score matching was used to adjust for patient demographics. Results: After propensity-score matching, outcome of 30 patients prospectively treated with lenvatinib (14 in clinical trials, 1 in early access program and 15 in real world setting) and 60 patients treated with cTACE as the initial treatment was compared. The change of ALBI score from baseline to the end of treatment were -2.61 to -2.61 for 30 patients in lenvatinib group (p = 0.254) and -2.66 to -2.09 in cTACE group (p < 0.01), respectively. The lenvatinib group showed a significantly higher objective response rate (73.3% vs. 33.3%; p < 0.001) and significantly longer median progression-free survival than the cTACE group (16.0 vs. 3.0 months; p < 0.001). Overall survival was significantly longer in the lenvatinib group than in the cTACE group (37.9 vs. 21.3 months; hazard ratio: 0.48, p < 0.01). Conclusion: In patients with large or multinodular intermediate-stage HCC exceeding the up-to-seven criteria with Child-Pugh A liver function, who usually do not benefit from TACE, lenvatinib provides more favorable outcome than TACE.

Children’s motor competence (MC) has declined in the past decades, while sedentary behavior (SB) has increased. This study examined the association between MC and physical activity (PA) levels among primary schoolchildren. Demographics, body height and weight, MC (Athletic Skills Track) and PA levels (ActiGraph, GT3X+) were assessed among 595 children (291 boys, mean age = 9.2 years, SD = 1.1). MC was standardized into five categories: from very low to very high. PA levels were classified into sedentary behavior (SB), light physical activity (LPA), and moderate-to-vigorous physical activity (MVPA). Mixed model analyses were conducted with PA levels as dependent variables and MC as the independent variable, while adjusting for age, gender, and BMI z-score on the individual level. Additional moderation analyses between covariates and MC and PA levels were also conducted. A negative association between MC and SB (β = -3.17) and a positive association between MC and MVPA (β =1.41) were found. The strength of both associations increased as children expressed lower or higher levels of MC. Increased age and being a girl were significant predictors of higher levels of SB and lower levels of MVPA. Non-overweight children spent significantly more minutes in MVPA compared with overweight children. No moderating effects of BMI, gender, and age were found on the association between MC and PA levels. MC is an important correlate of both SB and MVPA, particularly for children with very high or low MC. Developing and improving children’s MC may contribute to spending less time in SB and more time in MVPA, particularly for high-risk groups, i.e. children with low MC. Moreover, addressing MC development and PA promotion simultaneously might create positive feedback loops for both children’s MC and PA levels.

The practice of collecting, treating and management of solid waste prior to disposal has become a necessity in developing and modern societies. Over the years, it is known that most wastes that are disposed have a second hand value. However, the construction cost for conventional Material Recovery Facility(s) (MRFs) has been a major barrier for implementation. These technologies require considerable technical expertise, which is often not available in developing nations to successfully operate the MRFs. Covenant University; a private mission institution through her waste to wealth scheme is focused on managing and processing used materials to reusable products. These include Pet bottles, Paper wastes, Food wastes from cafeteria, plastic food packs, nylon, tin cans and others. Specific areas chosen for the Survey include the residential areas for staff and students and the two cafeterias. The waste generated was characterized based on the waste stream so as to quantify the amount of recyclable waste generated and most occurring. The survey involved the use of structured questionnaires, on-site observations and measurements. The study reveals an average amount of recyclable waste generated per day in the institution as 13.46% pet bottles, 4.03% paper, 55.56% food waste, 12.64% plastic, 9.63% nylon and 4.68% tin cans. The study established that adequate waste characterization is a requirement for effective integrated solid waste management which would boost resource recovery, reuse and recycling.

This paper investigates the effects of Inter-generational co-residence on health care market, and labor market outcomes, to see whether or not living under the same roof with at least one parent matters in health care market, and labor market behaviors in post-Affordable-Care Act (ACA) USA. The adopted analytical strategy involves not only looking at the gender differences in co-residence, and its effects on outcomes in the two markets, but also accounting for co-residence endogeneity following the recent literature. Unlike the recent literature that relies on instrumental variables methods, this study adopts a switching regression approach, defining inter-generational co-residence as an endogenous selection process using a binary probit equation, and modeled jointly with the extensive margins and intensive margins in the two markets. This novel approach results in a recursive trivariate probit model for each market, and estimated using penalized maximum likelihood methods. The results suggest that ACA by reorganizing the US health care market, seems to have reduced significantly disparities in health care access among males and females based on race, region of residence, place of birth, and citizenship. However not only do we observe significant differences in inter-generational co-residence status between males and females, we also find significant inequalities in the effects of co-residence on health care market, and labor market outcomes. In fact, co-residence is found to increase health care expenditure by 56.7% among females, while this figure increases to 74.2% among males. In addition co-residing individuals, while spending 69.7% more on health care annually are 1.22 times more likely to access health care, but 31% less likely to use health care intensively during the year. In the labor market, co-residence is found to reduce significantly hours of weekly labor supplied by 41% for females, and 55.6% for males. Furthermore co-residing individuals, while not significantly different in their likelihood of labor force participation, are 1.52 times less likely to work full time once they decide to participate, and also spend about 55.4% less time working in the labor market in post-ACA USA.

This study uses data from the pilot project "Community Monitoring for Better Health and Education Services Delivery Project'' in Burkina Faso, to model the joint impact of generic essential drugs and nursing staff supplies constraints on access to primary health care in the country. The results show that statistical endogeneity of supply side constraints are present in the standard univariate probit specification of access to care. However, when accounted for, the resulting Trivariate Probit model shows that although shortages of generic essential drugs supply do not seem to constitute a significant barrier to access in Burkina Faso, shortages in nursing staff supply do. In fact, the likelihood of primary care access is reduced by 85.5% among those that reported having experienced a shortage in nursing staff, while paradoxically increasing by 60.3% among those that reported having experienced a shortage in generic essential drugs. A potential explanation for these findings is that overall the health care needs in the three surveyed regions in the country were more linked to primary health care services consumption from nurses, although further research would be important to clearly elucidate the position of health goods such as generic essential drugs.

This paper proposes two fully-automatic machine-extracted linguistic features from an unlimited text input for Mandarin prosody generation. One is the punctuation confidence (PC) which measures the likelihood of inserting a major punctuation mark (PM) at a word boundary. Another is the quotation confidence (QC) which measures the likelihood of a word string to be quoted as a meaningful or emphasized unit in text. Because a major PM in a text is highly correlated with a prosodic break, and a quoted word string plays an important role in human language understanding, the two features potentially could provide useful information for prosody generation. The idea is first realized by employing conditional random field (CRF)-based models to predict major PMs, quoted word string locations, and their associated confidences, i.e., the PC and the QC, for each word boundary. Then, the predicted punctuations and their confidences are combined with traditional contextual linguistic features to predict prosodic-acoustic features. Both objective and subjective tests showed that the prosody generation with the proposed linguistic features performed better than the one without the proposed features. So, the proposed PC and QC are promising features for Mandarin prosody generation.

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

Vibration suppression in a field of frequencies and the creation of band gaps which do not allow the propagation of the waves is studied in this paper by means of microstructures designed through topology optimization. Topology optimization is formulated in frequency domain. Band gap design is based on Floquet-Bloch theory and genetic optimization. The result is appealing in view of modern 3D printing techniques.

Electronic skin is widely employed in multiple applications such as health monitoring, robot tactile perception, and bionic prosthetics. In this study, we fabricated millimeter-scale electronic skin featuring compact sensing units using Boston Micro Fabrication S130 (a high-precision additive manufacturing device) and the template removal method. We used a gallium-based liquid metal and achieved an inner channel diameter of 0.1 mm. The size of the sensing unit was 3 × 3 mm². This unit exhibited a wide linear sensing range (10–22000 Pa) and high pressure resolution (10 Pa) even on an ultracurved surface (radius of curvature was 6 mm). Sliding was successfully detected at speeds of 8–54 mm/s. An artificial nose with nine sensing units was fabricated, and it exhibited excellent multitouch and sliding trajectory recognition capabilities. This confirmed that the electronic skin functioned normally even on an ultracurved surface.

For centuries, humans have relied on natural products to prevent and treat numerous health issues. However, biologically active compounds from natural sources, such as polyphenols, face significant challenges, including low solubility, rapid metabolism, and instability, which hinder their effectiveness. Advances in science and nanotechnology have provided solutions to overcoming these problems through the use of porous silica materials. These materials possess unique properties, such as a high specific surface area, adjustable particle and pore sizes, and a surface that can be easily and selectively modified. In this review, we summarize and discuss findings on how the pore and particle size, structure, and surface modification of silica materials influence the preparation of efficient delivery systems for biologically active polyphenols from natural sources. The available data demonstrate how parameters such as adsorption capacity, release and antioxidant properties, bioavailability, solubility, stability, etc. of the studied delivery systems could be affected by the structural and chemical characteristics of the porous silica carriers.

In this study, AlSi12 alloy was fabricated using the selective laser melting (SLM) technique to produce high density components with complex and customized parts for railway applications. Nonetheless, the production of dense samples necessitates the optimization of production process parameters. As a statistical design of experimental technique, the response surface methodology was used to optimise different combination of SLM parameters. The results were analysed using analyse of variance (ANOVA) and the signal-to-noise(S/N) ratios. The relationship between the hardness response to the process parameters (scanning speed and lase power) for determining the optimal processing conditions were examined. A hardness value of 133 HV was obtained. The process parameters were successfully optimized and the relationship between the parameters and the structures of the fabricated samples were reported.

Daylighting design is not only a stage of dimensioning glazed surfaces to provide sufficient natural light to an occupied space, but also a method of analysing how this matter can be achieved without unwanted effects, such as: gains and losses of heat, glare, and variations of the daylighting intensity, at various indoor distances and levels. According to the international regulations in force, glazed surfaces must be designed with a careful balance between the admission of natural light and thermal performance, such as heat loss in winter and heat gain in summer. In a novel project, it is essential to determine the optimal ratio of window-to-wall surface area. This necessity arises because the materials constituting the glazed surfaces of windows typically exhibit lower insulation properties compared to those of the building's walls. This methodology could be applied to building renovations when envelope modifications are possible and suitable. The case study presented in the paper highlights the energy consumed due to a group of windows with a large glazed area in an existing building, located in a temperate continental climate area. The energy consumption results from supplementary artificial lighting required to maintain adequate illumination for indoor activities and that to counterbalance heat loss during colder periods are evaluated. The analysis performed by modifying the glazed surface led to the identification of an optimum value of windows dimensions for an energy consumed minimum.

The physical properties of nano-fertilizers (NFs) are important in determining their performance, efficacy, and environmental interactions. Nano-fertilizers, due to their small size and high surface area-to-volume ratio, enhance plant metabolic reactions, resulting in higher crop yields. The properties of nano-fertilizers depend on the synthesis methods used. The nanoparticle's nutrient use efficiency (NUE) varies among plant species. This review aims to analyze the relationship between the physical properties of NF and their influence on crop performance and nutrient uptake efficiency. The review focuses on the physical properties of NFs, specifically their size, shape, crystalline, and agglomeration. This review found that smaller particle-sized nanoparticles exhibit higher nutrient use efficiency than larger particles. Nano-fertilizer-coated additives gradually release nutrients, reducing the need for frequent application and addressing limitations associated with chemical fertilizer utilization. The shapes of nano-fertilizers have varying effects on the overall performance of plants. The crystalline structure of nanoparticles promotes a slow release of nutrients. Amorphous nano-fertilizers improve the NUE and, ultimately, crop yield. Agglomeration results in nanoparticles losing their nanoscale size, accumulating on the outer surface, and becoming unavailable to plants. Understanding the physical properties of nano-fertilizers is crucial for optimizing their performance in agricultural applications.

The detection accuracy of bridge superficial defect using the deep neural network approach decreases significantly under light variation and weak texture condition. To address these issues, an enhanced intelligent detection method based on the YOLOv8 deep neural network is proposed in this study. Firstly, multi-branch coordinate attention (MBCA) is proposed to improve the accuracy of coordinate positioning by introducing a global perception module in coordinate attention mechanism. Furthermore, a deformable convolution based on MBCA is developed to improve the adaptability for complex feature shapes. Lastly, the deformable convolutional network-attention-YOLO (DAC-YOLO) detection algorithm is formed by replacing the deep C2F structure in the YOLOv8 architecture with deformable convolution. A supervised dataset consisting of 4794 bridge surface damage images is employed to verify the proposed method, and results show that it achieves improvements of 2.0% and 3.4% in mAP and R. Meanwhile, the model complexity decreases by 1.2G, increasing the detection speed by 3.5/f·s-1.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Plasmonic sensors have great potential for widespread usage, but the prohibitive cost of noble metals restrains the wider adoption of this technology. The aim of our study is to develop a cost-effective Al-based alternative to plasmonic detectors commonly based on noble metals. We considered a structure that consists of a Si p-n junction with an overlying grating-relief aluminum layer. The investigation of the infrared plasmonic resonance dependency on the structure geometric parameters and optimization of the fabrication process allowed us to determine optimal parameters for photodetection enhancement. The resonance photoresponse of optimized aluminum-based plasmon-polariton photodetector was significantly improved and became comparable to noble metal-based analogs. Our results can be used for the creation of cost-effective high-sensitivity plasmonic sensors.

The beta-galactoside-binding mammalian lectin galectin-1 can bind, via its carbohydrate recognition domain (CRD), various cell surface glycoproteins and has been implicated in a range of cancers. As a consequence of binding to sugar residues on cell surface receptors it has been shown to have a pleiotropic effect across many cell types and mechanisms resulting in immune system modulation and cancer progression. As a result, it has started to become a therapeutic target for both small and large molecules. In previous studies, we have used fluorescence polarisation (FP) assays to determine KD values to screen and triage small molecule glycomimetics that bind to the galectin-1 CRD. In this study surface plasmon resonance (SPR) was used to compare human and mouse galectin-1 affinity measures with FP as SPR has not been applied for compound screening against this galectin. Binding affinities for a selection of mono- and di-saccharides covering a 1,000-fold range correlated well between FP and SPR assay formats for both human and mouse galectin-1. It was shown that slower dissociation drove the increased affinity at human galectin-1 whilst faster association was responsible for the effects at mouse galectin-1. This study demonstrates that SPR is a sound alternative to FP for early drug discovery screening and determining affinity estimates. Consequently, it also allows association and dissociation constants to be measured in a high throughput manner for small molecule galectin-1 inhibitors.

Abstract Background: Hypochlorous acid (HA) is a potent disinfectant with broad-spectrum antimicrobial activity against bacteria, fungi, and viruses. Aim: This study aimed to investigate the factors that influence the stability of hypochlorous acid (HOCl) and their impact on its disinfectant properties Methods: This study explored the stability of hypochlorous acid, emphasizing factors that affect its disinfectant efficiency, such as pH level, temperature, and the presence of organic materials. Findings: Our investigation revealed that HOCl is the most stable and effective disinfectant under weakly acidic conditions, where the undissociated form of hypochlorous acid is predominant. Although it is stable under various conditions, its efficacy is compromised by the presence of heavy metals, organic matter, and UV radiation. Conclusions: This comprehensive analysis concludes that, while hypochlorous acid is a highly effective disinfectant, understanding and maintaining the optimal conditions for its stability is crucial for maximizing its disinfection potential. Implications: The findings can be used to formulate new guidelines and regulations to guide the proper formulation, storage, and use of stable HOCL as disinfectants.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Persistent land subsidence or uplift can cause serious latent hazards to urban infrastructure. To thoroughly investigate the causes and impacts of land surface deformation, this study examines the case of Wuxi City, focusing on the land fluctuation patterns in the region following the enforcement of the groundwater abstraction prohibition policy in 2005. This research utilizes the PS-InSAR technique to quantify land surface deformations in the Wuxi region from November 2015 to June 2023 and analyzes 100 SAR images to obtain comprehensive spatiotemporal evolution data of the land surface. Furthermore, this study conducts an in-depth analysis of the effects of various factors, including groundwater, precipitation, and soil geology, on the characteristics of land surface deformation. It pioneers the application of the GARCH (Generalized Autoregressive Conditional Heteroskedasticity) model to analyze the time-series displacement in the study area and innovatively introduces the "amplitude factor" index to assess land surface fluctuations. This study investigates the recent land surface deformation patterns and mechanisms in Wuxi City. By integrating the "amplitude factor", it provides a scientific foundation for future urban development and disaster mitigation strategies in Wuxi City, offering valuable insights for related research.

Seasonal climatology of salinity fronts in the South Atlantic has been created from satellite SMOS sea surface salinity (SSS) measurements, 2011-2019, processed at the Barcelona Expert Center of Remote Sensing (BEC) and provided as high-resolution (1/20°) SSS data. The SSS fronts are identified with narrow zones of enhanced horizontal gradient magnitude (GM) of SSS computed with the Belkin-O’Reilly algorithm. Seasonal climatologies are generated for large-scale open-ocean SSS fronts and for low-salinity regions maintained by the Rio de la Plata discharge, Magellan Strait outflow, Congo River discharge, and Benguela upwelling. To facilitate feature recognition in satellite imagery, the salinity gradient has been log-transformed, which improved visual contrast of gradient maps, revealing new features. A 2000-km-long triangular area in the eastern tropical-subtropical Atlantic is filled with regular quasi-meridional mesoscale striations that form a giant ripple field with a 100-km wave length extending from Africa toward the NE Brazil. South of the Tropical Front, within the subtropical high-salinity pool, a trans-ocean quasi-zonal narrow linear belt of SSS maximum is documented. The Smax belt shifts north-south seasonally while retaining its well-defined linear morphology, which is suggestive of a mechanism that maintains this feature. In the SW Atlantic, the Rio de la Plata plume expands in winter (June-July), reaching across the South Brazilian Bight, up to Cabo Frio (23°S) and beyond. The Plata estuarine front moves in and out seasonally. Farther south, the Magellan Strait outflow expands northward in winter up to 39-40°S to nearly join the Plata outflow. In the SE Atlantic, the Congo River plume spreads radially from the river mouth, with the spreading direction varying seasonally and interannually. The plume is often bordered from the south by a quasi-zonal front along 6°S. The diluted Congo River water spreads southward seasonally down to the thermal Angola-Benguela Front at 16°S. The Benguela upwelling is delineated by a meridional front, which extends north alongshore up to 20°S, where the low-salinity Benguela upwelling water meets the high-salinity tropical water (“Angola water”) to form a salinity front, which is separate from the thermal Angola-Benguela Front at 16°S. The Angola water thus forms a wedge between the low-salinity waters of the Congo River outflow in the north and Benguela upwelling in the south. This high-salinity wedge is bordered by salinity fronts that migrate north-south seasonally.

This work presents a numerical study on atmospheric sound propagation over rough water surfaces. A method to generate pseudorandom sea profiles consistent with sea wave spectra is presented. The proposed method is suited to capture the logarithmic nature of the energy distribution of the waves. Sea profiles representing fully developed seas for sea states 2, 3, 4 and 5 are generated from the Elfouhaily et al. (ECKV) sea wave spectra. Excess attenuation caused by refraction and surface roughness is predicted with a parabolic equation (PE) solver. A novel method to estimate equivalent effective impedance based on PE predictions at different sea states is presented. Parametric expressions using acoustic frequency and significant wave height are developed for effective surface impedances. In this work, sea surface roughness is on a scale comparable to the acoustic wavelength. Under this condition, the acoustic scattering is primarily incoherent. This work shows the limitations of using an equivalent surface impedance in such incoherent scattering cases.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

Starting from the analysis of the lack of positivity of the Cattaneo heat equation, the article addresses the thermodynamic relevance of the positivity constraint in irreversible thermodynamics, than is at least as important as the entropic constraints. The fulfillment of this condition in hyperbolic models leads to the parametrization of the concentration fields with respect to internal variables associated with the microscopic dynamics. Using Brownian motion theory as a landmarking example for deriving macroscopic transport equations from the equations of motion at the particle/molecular level, we discuss two typical problems involving hydrodynamic interactions at microscale: surface chemical reactions at a solid interface of a diffusing reactant, and mass-balance equations in a complex viscoelastic fluid, in which the physics of the interaction leads either to the overcome the parabolic diffusion model or to consider the parametrization of the concentration with respect to the degrees of freedom associated with the relaxation dynamics of the solvent fluid.

The article presents a new method called slide roller burnishing (SRB) for cold working of cylindrical surfaces on machine tools, implemented with a novel multi-functional device. The machined material was chromium–nickel austenitic stainless steel. The deforming element is a toroidal roller whose axis crosses that of the workpiece. As a result, a relative sliding velocity occurs in the contact zone between the roller and the machined surface. The sliding velocity vector is set using the burnishing device. The theoretical background of SRB is presented. When the two axes are parallel, the well-known roller burnishing (RB) method is implemented. Thus, RB is a special case of SRB. Both processes are realized using the multi-functional burnishing device. The RB process was studied experimentally and optimized according to three criteria, based on the relationship between the surface integrity and operating behavio of the respective component, to achieve three processes: smoothing, hardening and mixed burnishing. Using the optimal RB parameters obtained, the dependence of the results of SRB on the crossing angle was investigated and optimized. A comparative analysis was performed between the optimized RB and SRB processes (respectively for their three variants: smoothing, hardening and mixed) based on geometrical and physical–mechanical characteristics of the surface integrity. The main advantage of the SRB is that it provides smaller height roughness parameters and a higher surface microhardness than RB.

Muscle fatigue caused by using staplers affects the surgical procedures of surgeons. Compared to manual staplers, electric staplers decrease the muscle fatigue by replacing repeated gripping and releasing with automatic model. Still powered by the battery, the electric staplers are confronted with new operation fatigue due to the extra weight of the battery. The weight and manual operation of the electric stapler can cause user's muscle fatigue. To tackle the unsettled fatigue issue, the study is to propose a new design method to offset the influence of extra weight of the battery attached to the electrical stapler by changing the opening and closing of the stapler end clamp to electric control. The purpose of this study is to verify whether the design of this electric stapler can offset the impact of weight. Experiments are set up to test the feasibility of the design on 12 male Chinese surgeons. The muscle fatigue is indicated by measuring the EMG (electromyography) signal, and the stapler's working effect is indicated by measuring the end movement of the stapler. The result shows the new-designed stapler reduce the operation fatigue, counteracting the impact of the battery weight.

Field-effect transistor (FET)-based biosensors stand as powerful analytical tools for detecting trace-specific biomolecules in diverse sample matrices, especially in the realms of pandemics and infectious diseases. The primary concern in applying these biosensors is their stability, a factor directly impacting the accuracy and reliability of sensing over extended durations. The risk of biosensor degradation is substantial, potentially jeopardizing sensitivity and selectivity and leading to inaccurate readings, including the possibility of false positives or negatives. This paper delves into the documented degradation of silicon nanobelt FET (NBFET) biosensors induced by buffer solutions. The results highlight a positive correlation between immersion time and the threshold voltage of NBFET devices. Secondary ion mass spectrometry analysis demonstrates a gradual increase in sodium and potassium ion concentrations within the silicon as immersion days progress. This outcome is ascribed to the nanobelt's exposure to the buffer solution during the biosensing period, enabling ion penetration from the buffer into the silicon. The study emphasizes the critical need to address buffer solution-induced degradation to ensure the long-term stability and performance of FET-based biosensors in practical applications.

The role of land surface temperature (LST) is of utmost importance in multiple academic disciplines such as climatology, hydrology, ecology, and meteorology. Until to now, many methods have been proposed to estimate LST from satellite thermal infrared data. The Thermal Infrared Sensor (IRS) on the Chinese ZY1-02E satellite is a pivotal instrument employed for gathering thermal infrared (TIR) data of land surfaces. The objective of this research is to evaluate the feasibility of a single-channel approach based on water vapor scaling (WVS) for deriving LST from ZY1-02E IRS data because of its wide spectrum range, i.e., 7~12μm, affected strongly by both atmospheric water vapor and ozone. Three study areas, namely Baotou, Heihe River Basin, and Yantai-sea sites, were selected as validation sites to evaluate the LST inversion accuracy. This evaluation was also conducted by cross-comparison between the retrieved LST and MODIS LST product. The results revealed that the WVS-based method exhibited an average bias of 0.63K and an RMSE of 1.62K compared to the in-situ LSTs. The WVS-based method demonstrated reasonable accuracy through cross-validation with the MODIS LST product, with an average bias of 0.77K and RMSE of 2.0K. These findings provide that the WVS-based method is effective to estimate LST from ZY1-02E IRS data.

As part of a comprehensive research on eco-friendly processing techniques, the influence of heat treatment environment on the case-hardening of AISI 1018 steel using pulverized cassava leaf was studied. The process was carried out at two different temperatures (850˚C and 950˚C) and under three environmental conditions: (Process 1) the control experiment, was carried out in air only, (Process 2) the medium comprised of pulverized cassava leaves, and (Process 3) the combination of pulverized cassava leaves plus barium carbonate (BaCO3) as an energizer (CBC mixture). Vickers microhardness testing and scanning electron microscopy were used to evaluate the effect of processing environment on case hardening of the steel. As expected, regardless of the processing temperature, Process 1 resulted in little or no hardening of the steel surface. However, notable case hardening occurred when steel specimens were subjected to either Process 2 or Process 3. Furthermore, the inclusion of barium carbonate in Process 3 significantly enhanced the case hardening effectiveness of the cassava leaf as it pertains to rate and maximum hardness achieved. Maximum enhancement was observed at 950oC. After 1 hour, the increase in hardness were 160% and 280%, for Process 2 and Process 3, respectively. Upon increasing the processing time to 5 hours, the increase in hardness due to Process 2 was raised to 254%, while that of Process 3 remained at approximately 280%. Diffusivity of AISI 1018 was calculated using the microhardness data. Diffusivity was highest in Process 2 samples with values of 1.568 x 10-9 m2/s at 850°C and 1.893 x 10-9 m2/s at 950 °C.

The paper presents the results of the study of tungsten surface structure modification under helium plasma irradiation. It is revealed that during irradiation of samples, surface modification in the form of relief development as a result of irradiation is observed. X-ray phase analysis showed that no new phases of the W system were found after irradiation, only an increase in the intensity of diffraction lines was observed. There are significant differences in the microstructure of tungsten depending on the temperature of helium plasma irradiation in the above range. It is assumed that the cause of defects is the extremely low solubility of helium in tungsten. Metallographic analysis has shown that at irradiation of tungsten samples in regime 5 and 6 the degree of relief development is not high in comparison with the tungsten sample irradiated in regime 4. The greatest increase in roughness of the sample irradiated in regime 5 was determined, which is associated with the formation of small cracks, blisters and pores in the surface layer. At the same time, in the samples irradiated in regime 6, the surface of which is characterized by chaotically located protrusions and depressions of various shapes, the roughness parameter Ra was 0.0603 µm. It was found that at temperature regimes T = 1200 °C and T = 1500 °C the microhardness of tungsten increases by 11% and 10% respectively.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

The watershed hydrologic conditions in the Madre de Dios (MDD) basin in the Peruvian Amazon have been irreversibly impacted by deforestation and changes in land use cover. These changes have also had detrimental effects on the geomorphology, water quality, and aquatic habitat within the basin. However, there is a scarcity of hydrological modeling studies in this area primarily due to the limited availability of hydrometeorological data. The primary objective of this study was to examine how deforestation impacts the hydrological conditions in the MDD basin. By implementing the Soil and Water Assessment Tool (SWAT) model, this study determined that replacing 12% of the evergreen broadleaf forest area with bare land resulted in an significant increase in surface runoff by 38% monthly, a reduction of evapotranspiration by 1% annually, and an average monthly streamflow increase of 12%. Changes in spatial patterns reveal that the primary impacted watershed is the Inambari River subbasin, a significant tributary of the Madre de Dios River. This area experiences an annual average surge of 187% in surface runoff generation while witnessing an annual average reduction of 8% in evapotranspiration.These findings have important implications, as they can contribute to instances of flooding and extreme inundation events, which have already occurred in the MDD region.

Background: The most frequent non-pigmented malignancy of the ocular surface is ocular surface squamous neoplasia (OSSN), which has a frequency of 0.03 to 1.9 per 100,000 people per year. It can be diagnosed histologically as anything from mild dysplasia to aggressive squamous cell carcinoma that affects both the conjunctiva and the cornea. The purpose of this study is to determine the distribution of ocular surface squamous neoplasia at a teaching hospital in South Western Uganda.Methods: In this retrospective study, we reviewed all records of patients with ocular surface squamous neoplasia from the Mbarara University of Science and Technology (MUST)/ Mbarara Regional Referral Hospital (MRRH) pathology laboratory in South Western Uganda, from January 2015- October 2021.Results: Of the 1,133 cases of ocular neoplasia seen during this time, OSSN composed of 26.7% (n=303). OSSN occurred mainly in females (59.1%). The most common OSSN was invasive squamous cell carcinoma (60.4%). The age range was 15-106 years while the mean was 39.99 years. The commonest affected age group was 30-44years (41.3%).Conclusion: The burden of OSSN is high. It primarily affects young adults and is frequently found in women. Squamous cell carcinoma makes up the majority of the disease.

The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a "plane" surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained "plane" effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.

Land surface temperature (LST) is a critical parameter for the dynamic simulation of land surface processes and for analyzing variations on regional or global scales. Obtaining LST with high spatiotemporal resolution is a subject of intensive and ongoing research. This study proposes a pixel-wise temporal alignment iterative linear regression model for downscaling based on MODIS LST products. This approach allows us to address the problem of high temporal resolution but low spatial resolution of the ERA5 reanalysis LST product, while remaining immune to pixel loss caused by clouds. The hourly ERA5 LST of the study area for 2012–2021 was downscaled to 1000 m resolution, and its accuracy was verified by comparison with measured data from meteorological stations. The downscaled LST offers intricate details and is faithful to the LST characteristics of distinct land-cover categories. In comparison with other downscaling techniques, the proposed technique is more stable and preserves the spatial distribution of ERA5 LST with minimal missing pixels. The pixel-wise average R-squared and mean absolute error for MODIS view times are 0.87 and 2.7 K, respectively, for cloud-free conditions at a 1000 m scale. Accuracy verification using data from meteorological stations indicates that the overall error is lower during cloudless periods rather than during overcast periods, during the night rather than during the day, and at MODIS view times rather than at non-view times. The maximum and minimum mean errors are 0.13 K for cloud-free periods and −0.98 K for cloudy periods, indicating a slight underestimation and overestimation, respectively. Conversely, the maximum and minimum mean absolute errors are 2.01 K for the daytime and 0.85 K for the nighttime. Therefore, the model ensures higher accuracy during cloudy periods with only clear sky LST as input data, making it suitable for long-term, all-weather ERA5 LST downscaling.

The azimuth wheel-rail of large aperture radio telescope is the key component, it not only sup-ports the whole weight of the antenna, but also directly affects the pointing performance of the antenna with its surface accuracy. The whole weight of the radio telescope is hundreds or even thousands of tons, its azimuth frame rollers have great contact stress with the wheel-rail surface, repeated rolling can cause rolling contact fatigue on the wheel-rail surface, resulting in wear, cracks and other damage to the wheel-rail, and even lead to failure or fracture of the wheel-rail in serious cases, so it is very important to monitor the damage of the antenna wheel-rail. In order to visually detect the use of antenna wheel-rail surface, this paper proposed the method using electromagnetic ultrasonic detection to detect the damage of antenna wheel-rail surface for the first time. Based on the electromagnetic ultrasonic nondestructive testing principle, the simplified wheel-rail model containing wear, corrosion and crack damage is simulated. The results show that this method can effectively detect the surface damage of the antenna wheel-rail surface, and it can provide an important reference for the research of wheel-rail damage detection of large radio telescope.

Finishing coatings used in the wood-based composites industry play a key role in the final appearance of the finished product. However, the use of such coatings is not only for aesthetic purposes but also to protect the product against surface damage and moisture or minimize the emission of harmful substances. The latter is an extremely important factor in terms of safety for both the manufacturer and the user, which is why the emissivity test is one of the most important tests in the case of finishing coatings. Such a role can be played by carbon-rich materials, such as those remaining from the extraction of birch bark. In this article, an attempt was made to create coatings in the form of a film by combining a biopolymer with suberinic acid residues (SAR). There were two types of biopolymers used – polylactide (PLA) and polycaprolactone (PCL), in various polymer-SAR ratios. SAR as a residue, is a material that bounds CO2 from the atmosphere and creates a possibility of further use. As part of this study, the obtained coatings were tested in terms of resistance to scratch, relative hardness, cold liquids, total volatile organic compounds (TVOC) and formaldehyde emission, surface absorption etc. Differences in the polymers used and the effect of the SAR additive on selected surface properties were demonstrated. The addition of carbon-rich SAR significantly improves the gas barrier properties of the surface finishing materials based on PLA and PCL. The relative hardness and scratch resistance has also increased with raising SAR content. However, the increasing content of SAR filler act as a limiter in the depth of penetration of deposited surface finishing materials onto the wood surface.

A new biosensor based on Surface Plasmon Resonance Imaging detection technique for quantitative determination of Fibroblast Growth Factor-23 has been developed. The FGF-23 is mainly produced in the bone tissues as a phosphaturic hormone that upon secretion creates a trimeric complex with FGF receptor 1 and αKlotho. FGF-23 acts on the kidneys: it stimulates phosphate excretion and suppresses formation of active vitamin D. It has been proven that FGF-23 plays a role in bones’ carcinogenesis and its metastasis. The newly developed method based on the SPRi biosensor has been validated – the precision and accuracy as well as selectivity were acceptable and gave less than ±10% of recovery. The linear response of the biosensor ranges 1– 75 pg/ml. The limit of detection was 0.033 pg/ml and limit of quantification was 0.107 pg/ml. The biosensor was used to determine FGF-23 concentration in the plasma of healthy individuals as well as in the plasma of the patients with the clear cell carcinoma of the kidneys. The obtained results were compared with the results of the ELISA measurements. The determined Pearson correlation coefficients were close to 1 what showed that the newly developed biosensor can be used as the competitive method to the ELISA.

The rock strata movement deformation generated by the mining process of the mine will inevitably lead to surface subsidence and a series of environmental hazards, so it is particularly important to monitor the rock strata movement deformation and surface subsidence in the goaf area. With the development of surface subsidence monitoring technology, InSAR technology has been widely used in the research of surface subsidence in mining areas with the advantages of high precision and wide monitoring. In this paper, by obtaining the image data of 59 Sentinel-1A scenes in the mining area, the obtained PS points were analyzed and processed by ArcGIS difference analysis by PS-InSAR technology, and the surface deformation cloud map and settlement curve of the mining area in various periods were obtained, and the rock strata movement deformation and surface subsidence law of the goaf before treatment and after different treatment methods were studied by influencing factors such as stope layout and mining depth. The results show that the rock strata movement deformation and surface subsidence degree of the goaf under different treatment methods are different due to different influencing factors, and their positions also change dynamically with time. Applying InSAR technology to study rock strata movement deformation and surface subsidence can provide an important basis for mine safety mining, goaf treatment, rock strata movement deformation and surface subsidence monitoring.

Solar energy is a rapidly growing sector, and solar farms are playing an increasingly important role in meeting the world's energy needs. However, as the size and complexity of these farms increase, so do the challenges associated with managing them efficiently. This article presents a comprehensive analysis of the fundamental parameters that underpin solar energy systems. Focusing on the latest research, we examine the challenges and opportunities intrinsic to the implementation of solar energy systems, paying particular attention to the various parameters that contribute to their performance. These parameters encompass a range of factors such as thermal performance, atmospheric boundary layer, solar energy meteorology, heat islands, cloud influences, agrivoltaic systems, shading factors, and surface energy budget. The review underscores the importance of considering a diverse array of parameters when developing solar energy systems to optimize their efficiency and effectiveness. Ultimately, by unraveling these challenges and opportunities, we can work towards creating more sustainable and reliable renewable energy sources and reducing our dependence on non-renewable alternatives.

Arsenic (As) contamination of groundwater is a common problem in BDP. The alkaline pH of the groundwater provides favourable condition for geomicrobiochemical processes, where organic matter also plays an important role in mobilization of As. The total arsenic content (AsT) of the groundwater is in the range of 69-178 µgL-1 with mean value of 118.58 µgL-1. The groundwater quality of monitored drinking water wells are related to local land–use pattern and rural sanitation installation and practices (which can have a strong influence on microbial contamination). The study indicates that As heterogeneity, probably a consequence of microbial heterogeneity is a feature of the study area. The excessive total and fecal coliform (TC and FC) count of the ponds possibly suggest uncontrolled surface run offs and sewage leakage, notably from nearby pit-latrine, which increased the microbial contamination in these water sources. The tube wells located in close proximity (~ 2-3 m) of the surveyed ponds are also contaminated with high TC and FC values, due to faulty water supply system, pond water infiltration and cracked tube well platforms. Coliforms may influence geomicrobiological processes in groundwater and thereby, contribute in As release and mobilization. The TC and FC values of monitored tube wells and ponds show seasonal variation, with high TC and FC values during wet season. Attempt has been made to focus on sanitation risk of the monitored wells (based on sanitation and fecal coliform scores) which is usually less explored. The sanitary risk score reveal the need of immediate attention to all the sites, as 25.0 %, 58.3 %, 11.1 % and 5 % of tube wells of the six sites fell under very high risk (sanitary risk score ≥ 9), high risk (sanitary risk score 6-8), intermediate risk (sanitary risk score 3-5) and low risk category (sanitary risk score 0-2), respectively. Fecal coliform score classified all the sites under intermediate risk category (FC count 10-100 per 100 ml of water). The predominance of As heterogeneity particularly in areas under high risk category (showing high TC and FC contamination) is observed along with the similar sinusoidal pattern of TC, FC and AsT content. Finally, this study shed light on the factors responsible for unsafe nature of monitored tube wells and the influence of anthropogenic activities on the microenvironment of the groundwater, which could be a probable reason behind the As heterogeneity in the groundwater of the study area.

The constant increase in current density in electrical wires leads to increasingly significant heat losses due to Joule effect. Therefore, reducing the electrical resistivity of copper wires becomes necessary. To achieve this goal, the development of a composite material incorporating a more conductive reinforcement, the graphene, is a promising way. The design of a copper/graphene composite using a powder metallurgy-based method is presented. This synthesis method allows for interface control through the growth of CuO(Cu) nanoparticles tightly bonded to the reinforcement. It also involves the dispersion of graphene through ultrasonic treatment and its alignment within the matrix using a uniaxial pressing densification method. The increase in the hardness (+12 HV) demonstrates the effective dispersion and separation of graphene layers. The impact on the electrical properties of dendritic copper (ρe = 2.30 µΩ.cm) remains limited, with a decrease in electrical resistance of approximately 1.4%. However, for copper with higher electrical resistivity, flake copper (at 2.71 µΩ.cm) and brass at (7.66 µΩ.cm), reductions of 2.7% and 10% have been achieved, respectively. With the improvement of graphene quality, there is more room to improve the electrical properties. This work paves the way for the development of composites with improved electrical resistivity.

Purpose Professional oral hygiene procedures are recommended by dentists, twice a year. BioHPP is a polyetheretherketone polymer used in prosthetic dentistry as a frame material. The aim was to investigate whether routine dental cleaning procedures such as ultrasonic scaling and brushing affect the surface proprieties of prosthetic BioHPP restorations. To evaluate the surface properties of different restorations based on BioHPP (veneered with composite resin and polished) after brushing and ultrasonic scaling exposure. Materials and Methods The 66 BioHPP specimens were divided into three groups (n=22). The first group was the control group, and no further treatment was applied. The specimens in the second group were veneered with composite resin and in the third group the specimens were veneered with composite resin and polished. Each group of samples was divided into 3 subgroups: 0- no treatment, 1-exposed to tooth brushing, 2-exposed to ultrasonic scaling. The surface morphology was investigated by atomic force microscopy (AFM). The structure of samples was analysed using the XRD technique, and the surface wettability was done. Results Control group specimens were significantly rougher compared to other groups (p ≤ 0.05). There was no statistically significant difference in the contact angle of water analyses between the samples. Conclusion: Composite veneered BioHPP showed the highest surface resistance to brushing and ultrasonic scaling.

The development of efficient mucosal vaccines is strongly dependent on the use of appropriate vectors. Various biological systems or synthetic nanoparticles have been proposed to display and deliver antigens to mucosal surfaces. The Bacillus spore, a metabolically quiescent and extremely resistant cell, has also been proposed as a mucosal vaccine delivery system and shown able to conjugate the advantages of live and synthetic systems. Several antigens have been displayed on the spore by either recombinant or non-recombinant approaches, and antigen-specific immune responses have been observed in animals immunized by the oral or nasal route. Here we review the use of the bacterial spore as a mucosal vaccine vehicle focusing on the advantages and drawbacks of using the spore and of the recombinant vs. non-recombinant approach to display antigens on the spore surface. An overview of the immune responses induced by antigen-displaying spores so far tested in animals is presented and discussed.

MCrAlYHf bond coats are employed in jet and aircraft engines, stationary gas turbines, and power plants, which require strong resistance to oxidation at high temperatures. The oxidation behavior of a free-standing CoNiCrAlYHf coating was investigated in this study. Isothermal oxidation tests were performed in air at 1050 °C on the specimens with various levels of surface roughness to investigate the oxidation kinetics. X-ray diffraction, focused ion beam, scanning electron microscopy (SEM), and scanning transmission electron microscopy were used to characterize the surface oxides. The surface roughness was examined using a contact profilometer and SEM. An empirical model was proposed to elucidate the impact of surface roughness on the oxidation behavior based on the correlation between the surface roughness level and oxidation rates.

Road infrastructure is a key public asset because it benefits the social and economic development of any country. It plays an important role for the development of the industrial complex, the production sector and the road surfaces of transport roads should be of high quality, have a long service life. Road infrastructure, as well as all infrastructure, requires preservation, maintenance and repair. There are special requirements for the roadway that must be observed during construction or repair. This article is devoted to a detailed study of the use of fiber optics sensors (FOS) based on the fiber Bragg grating (FBG) for road surface monitoring. Such a fiber sensor consisting of a fiber Bragg grid and a pair of grids can offer the possibility of simultaneous measurement of deformation and temperature for monitoring the pavement. Temperature and deformation measurements were carried out by installing a sensor on the surface of a made asphalt sample. The built-in fiber sensor based on FBG provides important information about how the pavement structure can withstand the load, subsidence of soil, timely implement road safety and stability measures evaluate and predict the service life of the pavement. The results of the study showed that the synchronicity, repeatability and linearity of the characteristics of the fiber sensor are excellent. The difference between the experimental and theoretical results is about 7%. Thus, based on the results of the obtained data, the fiber sensor on the FBG can be used for monitoring, designing road surfaces and in general transport infrastructure.

The paper focuses on two unconventional magnetic field-based treatment regimes applied to an alloyed steel before applying a thermochemical treatment. This study was conducted in order to improve the behavior of the chosen material during the wear process. Increasing the wear resistance and the micro-hardness of the superficial layer obtained from the treatments are a priority, as well as improving the mechanical properties of a Cr-Mo alloyed steel. Thermomagnetic treatment, applied before plasma nitriding treatment, improves the mechanical properties of the base material, especially in the case of a steel with a considerable chromium content (1,02%). This paper is a review of my own researches in the last years.

Many studies have focused on the impacts of rainfall duration and intensity while overlooking the role of rainfall patterns on intensive tillage erosion in hilly agricultural landscapes. The objective of this study was to determine the combined effects of rainfall patterns and intensive tillage erosion on surface runoff and soil loss on sloping farmland in the purple-soil area of China. Five simulated rainfall patterns (constant, rising, falling, rising-falling, and falling-rising) with the same total precipitation were designed, and the intensive tillage erosion treatment (IT) and no-tillage treatment (NT) were subjected to simulated rainfall using rectangular steel tanks (2 m × 5 m) with a slope of 15°. To analyse the differences in the hydrodynamic characteristics induced by tillage erosion, we calculated the flow velocity (V), Reynolds number (Re), Froude number (Fr), and Darcy-Weisbach resistance coefficient (f). The results indicate that significant differences in surface runoff and soil loss were found among different rainfall patterns and stages (P < 0.05). The falling pattern and falling-rising pattern had faster runoff-initiating times and larger sediment yields than those of the other rainfall patterns. f varied from 0.30 to 9.05 for the IT and 0.48 to 11.57 for the NT and exhibited an approximately inverse trend to V and Fr over the course of the rainfall events. Compared with the NT, the mean sediment yield rates from the IT increased the dynamic range of 8.34%–16.21% among different rainfall patterns. The net contributions of the IT ranged from 2.77% to 46.39% on surface runoff and 10.14%–78.95% on soil loss on sloping farmland. Surface runoff and soil loss were positively correlated with rainfall intensity, V, and Fr but negatively correlated with f irrespective of tillage intensive (P < 0.05). For varying-intensity rainfall patterns, soil and water loss fluctuated during rainfall events, suggesting that the changes in rainfall intensity and tillage intensity would result in drastic variations in soil hydrological characteristics and sediment transport mechanisms. The time sequences of rainfall intensity in each rainfall pattern significantly affected surface runoff, soil erosion, and their contribution rates to total soil and water loss. Moreover, tillage erosion effects on soil and water loss were closely related to rainfall patterns in hilly agricultural landscapes. Our study not only sheds light on the mechanism of tillage erosion and rainfall erosion but also provides useful insights for developing tillage-water erosion prediction models to evaluate soil and water loss on cultivated hillslopes.

During few last years, climate change including global warming which is attributed to human activities and also its long-term adverse effects on the planet’s functions have been identified as the most challenging discussion topics which have arisen many concerns and efforts to find the possible solutions. Since the warmth arising from Earth’s landscapes affects the world’s weather and climate patterns, we decided to study the changes in the Land Surface Temperature (LST) patterns in different seasons through non-linear methods. Here, we particularly want to estimate the non-integer dimension and fractal structure of the land surface temperature. For this study, the (LST) data has been obtained during the daytime by the Moderate Resolution Imaging Spectroradiometer (MODIS) on NASA’s Terra satellite. Depending on what time of the year data has been collected, temperatures change in different ranges. Since equatorial regions remain warm, and Antarctica and Greenland remain cold, and also because altitude affects temperature, we selected Riley County in the U.S. state of Kansas, which does not belong to any of this type locations and we are interested to observe the seasonal changes in temperature in this county. The results of the present study show that the Land Surface Temperature (LST) belongs to the class of fractal process with non-integer dimension.