This paper reports a novel fabric phase sorptive extraction-high performance liquid chromatography-ultra violet detection (FPSE-HPLC-UV) method for the simultaneous extraction and analysis of four phenyltin derivatives that include triphenyltin hydroxide, triphenyltin acetate, triphenyltin chloride and tetraphenyltin in environmental water (agricultural waste water and municipal waste water) and canned food samples. The selected analytes were well resolved by Waters Nova pack C18 column (3.9 x 150 mm, 4 µm particle size) in isocratic elution mode within 15 minutes. The new microextraction media has been analytically evaluated using phenyltin derivatives as model compounds. The factors affecting the extraction efficiency of FPSE have been evaluated and the optimum extraction conditions were determined. Under these optimum conditions, the limits of detection (LODs) for sol-gel C18 coated fabric phase sorptive extraction (FPSE) media in combination with HPLC-UV for the analysis of the phenyltin derivatives were in the range of 10-100 ng/mL with high precision (low relative standard deviation) at 10 ng/mL concentration with good absolute recoveries. To the best of our knowledge, this is the first FPSE extraction procedure applied to environmental water and canned food samples for the simultaneous determination of phenyltin derivatives and could be readily adopted as a rapid and robust green analytical tool for routine environmental and food analytical laboratories.

Viruses can infect a cell via one or both routes viz. cell-to-cell (c-c) or cell-free (c-f) . Pathogenesis studies of various viruses, including HIV, have shown that c-c transmission yields a significantly higher infection magnitude than the c-f route. Expectedly, potent antibodies inhibited c-f infection more efficiently than with c-cell transmission. To achieve a one-step, synchronous infection cycle that provides amplified infection, we have studied a consistent and efficient c-c HIV infection model since 1992. H9 cells persistently infected with HTLV-IIIB (H3B cells) and uninfected target CD4+ lymphocyte line (HuT78) were mixed in a ratio of 1:4 respectively. We have recently used this model to produce HIV designer antigens that have been shown to elicit monoclonal as well as polyclonal specific antibodies against novel epitopes that are formed post virus-cell engagement, but prior to fusion. The model can be extended for HIV neutralizing antibody assays or drug inhibitors against high multiplicity of infection.

Machine learning (ML) has found increasing use in research on energy conversion and storage technologies, in particular, so-called sustainable technologies. While often ML is used to directly optimize the parameters or phenomena of interest in the space of features, in this perspective, we focus on using ML to construct objects and methods that help in or enable the modeling of the underlying phenomena. We highlight the need for machine learning from very sparse and unevenly distributed numeric data in multidimensional spaces in these applications. After a brief introduction of some common regression-type machine learning techniques, we will focus on more advanced ML techniques which use these known methods as building blocks of more complex schemes and thereby allow working with extremely sparse data and also allow generating insight. Specifically, we will highlight the utility of using representations with sub-dimensional functions by combining the high-dimensional model representation ansatz with machine learning methods like neural networks or Gaussian process regressions in applications ranging from heterogeneous catalysis to nuclear energy.

Background: Active case finding for TB was implemented in selected sixty high TB burden wards of Kolkata, India. Community volunteers called TOUCH agents (TAs) identified and referred presumptive TB patients (PTBPs) to health facilities for TB diagnosis and treatment. We aimed to describe the ‘care cascade’ of PTBPs identified during July to December, 2018 and to explore the reasons for attrition as perceived by TAs and PTBPs. Methods: An explanatory mixed methods study with quantitative phase of cohort study using routinely collected data followed by descriptive qualitative study with in-depth interviews was conducted. Results: Of the 3, 86,242 individuals enumerated, 1132 (0.3%) PTBPs were identified. Only 713 (63.0%) PTBPs visited referred facility for TB diagnosis. TB was diagnosed in 177 (24.8%) and the number needed to screen for one TB was 2,183 individuals. The potential reasons for low yield were stigma and apprehension about TB, distrust about TA, wage loss for attending health facilities and substance abuse among PTBPs. Conclusion: The yield of ACF was suboptimal with low PTBP identification rate and high attrition rate. Interviewing each individual for symptoms of TB and supporting PTBPs for diagnosis through sputum collection and transport can be adopted to improve the yield.

Black barley seeds are a health-beneficial diet resource because of their special chemical composition and antioxidant properties. The black lemma and pericarp (BLP) locus was mapped in a genetic interval of 0.807 Mb on chromosome 1H, but its genetic basis remains unknown. In this study, targeted metabolomics and conjunctive analyses of BSA-seq and BSR-seq were used to identify candidate genes of BLP and the precursors of black pigments. The results revealed that five differentially expressed genes identified on the 1H chromosome were candidate genes of the BLP locus, and 17 differential metabolites, including the precursor and repeating unit of allomelanin, were accumulated in the grain-filling stage of black barley. Phenol nitrogen-free precursors such as catechol (protocatechuic aldehyde) or catecholic acids (caffeic, protocatechuic, and gallic acids) may promote black pigmentation. BLP can manipulate the accumulation of benzoic acid derivatives (salicylic acid, 2,4-dihydroxybenzoic acid, gallic acid, gentisic acid, protocatechuic acid, syringic acid, vanillic acid, protocatechuic aldehyde, and syringaldehyde) through the shikimate/chorismite pathway other than the phenylalanine pathway and alter the metabolism of the phenylpropanoid-monolignol branch. Collectively, it is reasonable to infer that black pigmentation in barley is due to allomelanin biosynthesis in lemma and pericarp, and BLP regulates melanogenesis by manipulating the biosynthesis of its precursors.

Increasing of the imaging rate of conventional atomic force microscopy (AFM) is almost impossible without impairing of the imaging quality, since the probe tip tends to lose contact with the sample. We propose to apply the additional nonlinear force on the upper surface of a cantilever, which will help to keep the tip and surface in contact. In practice this force can be produced by the precisely regulated airflow. Such an improvement affects the AFM system dynamics, which were evaluated using a mathematical model presented in this paper. The model defines the relationships between the additional nonlinear force, the pressure of the applied air stream and the initial air gap between the upper surface of the cantilever and the end of the air duct. It was found that the nonlinear force created by the stream of compressed air (aerodynamic force) prevents the contact loss caused by the high scanning speed or higher surface roughness, and at the same time has minimal influence on the interaction force, thus maintaining stable contact between the probe and the surface. This improvement allows to effectively increase the scanning speed by at least 10 times using a soft (spring constant of 0.2 N/m) cantilever by applying the air pressure of 40 Pa. If a stiff cantilever (spring constant of 40 N/m) is used, the potential of accuracy improvement reaches 92 times. This method is suitable for use with different types of AFM sensors and can be implemented practically without essential changes in AFM sensor design.

Background: In regenerative dentistry the graft material influences the success. It should act as an osteoconductive scaffold, providing a mineral substrate during resorption and inducing the activity of osteoinductive cells capable of producing new bone, platelet growth factors, and cell differentiation factors inducing the differentiation of undifferentiated mesenchymal cells into. Given that dentin shares many biochemical characteristics with bone tissue, it has recently attracted considerable interest as a biomaterial for bone repair. The aim of this study is to compare two grinder types in order to determine the optimal method for producing dentinal particles using a mechanical grinder. Materials and methods: A sample of 40 natural human teeth without restorations, prostheses or root canal treatments was used and divided into two groups subjected to two different grinder speeds (high-speed and low-speed). The high-speed showed a greater dispersion (53.5+-9.89% of the tooth) due to the pulverisation (highly thin granules) of part of the tooth. The low-speed grinder does not pulverize the dentin and the percentage of tooth loss is 9.16+/-2.34%. Conclusion: The low-speed gringer allows to save a major part of the tooth and to have a maximum quantity of graft material but requires more time. Further studies must be promoted to optimise the grinding procedures.

The high radio frequency polarization imaging of non-thermal emission from active galactic nuclei (AGN) is a direct way to probe the magnetic field strength and structure in the immediate vicinity of supermassive black holes (SMBHs) and is crucial in testing the jet-launching scenario. To explore the the magnetic field configuration at the base of jets in blazars, we took advantage of the full polarization capabilities of the GMVA (Global Millimeter VLBI Array). With an angular resolution of ~50 micro-arcseconds at 86 GHz, one could reach scales down to ~900 Schwarzschild radii (for a 10^9 solar mass black hole). We present here the preliminary results of our study on the blazar BL Lac. Our results imply that on sub-mas scales the core and central jet of BL Lac is significantly polarized with two distinct regions of polarized intensity. We also noted a great morphological similarity between the 7mm/3mm VLBI images at very similar angular resolution.

Microarray patches (MAPs) have the potential to be a safer, more acceptable, easier to use, and more cost-effective means for the administration of vaccines than injection by needle and syringe. Here, we report findings from a randomized, partially double-blind, placebo-controlled Phase I trial using the Vaxxas high-density MAP (HD-MAP) to deliver a measles rubella (MR) vaccine. Healthy adults (N = 63, age 18–50 years) were randomly assigned 1:1:1:1 to four groups: uncoated (placebo) HD-MAPs, low-dose MR HD-MAPs (~3,100 median cell-culture infectious dose [CCID50] measles, ~4,300 CCID50 rubella); high dose MR-HD-MAPs (~9,300 CCID50 measles, ~12,900 CCID50 rubella); or a sub-cutaneous (SC) injection of an approved MR vaccine, MR-Vac (≥1,000 CCID50 per virus). The MR vaccines were stable and remained viable on HD-MAPs when stored at 2–8°C for at least 24 months. When MR HD-MAPs stored at 2–8°C for 24 months were transferred to 40°C for 3 days in a controlled temperature excursion, loss of potency was minimal, and MR HD-MAPs still met World Health Organisation (WHO) specifications. MR HD-MAP vaccination was safe and well-tolerated; any systemic or local adverse events (AEs) were mild or moderate. Similar levels of binding and neutralizing antibodies to measles and rubella were induced by low-dose and high-dose MR HD-MAPs and MR-Vac. The neutralizing antibody seroconversion rates at day 28 after vaccination for the low-dose HD-MAP, high-dose HD-MAP and MR-Vac groups were 37.5%, 18.8% and 35.7% respectively for measles and 37.5%, 25.0% and 35.7% respectively for rubella. Most participants were seropositive for measles and rubella antibodies at baseline, which appeared to negatively impact the number of participants that seroconverted to vaccines delivered by either route. The data reported here suggest HD-MAPs could be a valuable means for delivering MR-vaccine to hard-to-reach populations and support further development. Clinical trial registry number: ACTRN12621000820808.

Patients with pT1 high-grade (HG) bladder cancer (BC) and a very high risk of progression might benefit from immediate radical cystectomy (RC), but this option remains controversial. Validation of a standardized method to evaluate the extent of lamina propria (LP) invasion (with recognized prognostic value) in transurethral resections (TURBT) specimens is still needed. The Rete Oncologica Lombarda (ROL) system showed a high predictive value for progression after TURBT in recent retrospective studies. Our aim was to validate ROL system on a large mono-institutional prospective series of primary urothelial carcinomas. From 2016 to 2020, we adopted ROL for all patients with pT1 HG BC on TURBT. We employed a 1.0-mm threshold to stratify tumors in ROL1 and ROL2. A total of 222 pT1HGBC were analyzed. Median age was 74 years, with male predominance (73.8%). ROL was feasible in all cases: 91 cases were ROL1 (41%) and 131 ROL2 (59%). At a median follow up of 26.9 months (IQR 13.8-40.6), we registered 80 recurrences and 40 progressions. ROL was a significant predictor of tumor progression at both univariable (HR 3.53; CI 95% 1.56 – 7.99; p<0.01) and multivariable (HR 2.90; CI 95% 1.25 – 6.75; p=0.01) Cox regression analyses. At Kaplan-Meier estimates, ROL showed correlation with both PFS (p=0.0012) and RFS (p=0.0167). Our results confirmed the strong predictive value of ROL for progression on a large prospective series. We encourage the application of ROL for reporting the extent of LP invasion, substaging T1 HG BC, and improving risk tables for urological decision making.

With the ever-increasing rate, obesity has become an epidemiological problem throughout the globe comprising about 39% of the world population as of now. Among several reasons, disruption of the gut microbial ecosystem might contribute to the pathogenesis of metabolic disorders, including obesity, metabolic syndrome, type 2 diabetes, and other associated comorbidities. Though the mechanisms related to dysbiosis are unclear, diet might play a modulating role where different dietary approaches manipulate microbial richness and abundance as well as stability. For instance, shifting of Firmicutes and Bacteroidetes ratio in the gut might have a role in association with the dietary approaches and ingestion duration. Along with altered gut microbial composition, microbial metabolites such as short-chain fatty acids (SCFA) after ingestion of non-digestible dietary starches may have an impact on host metabolism by regulating lipogenesis, gluconeogenesis, and inflammation with potential associations to health and obesity. The dietary approaches like carbohydrates, fibre, protein, and/or fat diet at various arrangements can make a shift in the composition of gut microbiota if introduced for a short period. However, the unique pattern of the gut microbes usually remains the same along with the longer period of habitual diet. Though the short-term dietary intervention or circadian rhythm influences a transient change in gut microbes, other than habitual diet, the understanding related to long-term dietary change-induced permanent alterations is minimum. Alternatively, the usage of prebiotics, probiotics as well as postbiotics could be beneficial to overcome dysbiosis. This review highlights the current knowledge and the interaction between the human intestinal microbiota and diet as a modifying factor, in obesity allowing the scientists to uncover novel targets and tools to use as customized therapy.

The salt marshes, lying at the land-sea temperate interface, furnish a plethora of ecosystems services such as biodiversity niche support, ocean-climate change regulation, ornithology recreo-tourism or plant gathering by hand. They undergo significant worldwide losses due to their conversion into crop fields and to their spatial compression between the rising sea-level and the armoring shoreline. Their monitoring however requires to use a suite of remote sensing sensors to embrace the regional scale while capturing the plant details. This research innovatively adopts a multiscale approach using a cascading spaceborne and airborne process, from the 10-m Sentinel-2, through the 3-m Dove, to the 0.03-m unmanned airborne vehicle (UAV) imageries. The high to very high temporal resolution of the Sentinel-2 and Dove enabled to cover twenties and tens of km2 over five and four years, respectively, in the form of normalized difference vegetation index (NDVI) classes, associated with microphytobenthos, low, medium and high salt marsh vegetation, including the opportunistic Elyma genus. The NDVI was then modelled at the UAV scale (a few km2) using a three-layered NN prediction, providing the final near-infrared (NIR), and the intermediate red, green and blue reflectance imageries, calibrated/validated/tested with the Dove reflectance imageries (R2NIR=0.98, R2red=0.88, R2green=0.84, and R2blue=0.90). The 100fold increase in pixel size allowed to detect the decimeter-scale objects of the tidal flats and salt marshes, to enlarge the NDVI class ranges, and hold great promise to model other spectral bands at the UAV scale for further deeply enhancing the salt marsh mapping.

Background: Infantile tibia vara (ITV) is a rare proximal tibia deformity in infancy, leading to progressive knee varus. High tibial osteotomy is commonly practiced but has high recurrence rates. This study analyzed factors affecting treatment failure and recurrence in children undergoing opening-wedge high tibial osteotomy (OWHTO) for ITV. Methods: We retrospectively studied children with ITV who had OWHTO with press-fit cancellous bone allograft between 2000 and 2020, with ≥2-year follow-up. Outcomes included recurrence (knee varus with tibiofemoral angle >10°), complications, and reintervention. Results: We analyzed 39 knees in 29 patients (mean age: 4.8 ± 1.9 years; median follow-up: 7.4 years). Recurrence occurred in 22 cases (56%). Age at surgery significantly influenced recurrence, with rates of 16% before age 5 versus 95% later (hazard ratio: 12.0, p = 0.001). Langenskiöld stage also affected recurrence (β-coefficient: 2.7, 95% C.I. 1.0–4.5, p = 0.002; pseudo-R-squared: 0.50, p = 0.001), with recurrence in all stage III IV or higher cases. Conclusions: Early diagnosis and treatment before age 45, ideally with Langenskiöld stage III or lower, are crucial for stable correction with OWHTO alone. Late, high-grade ITV may require combined, acute or gradual, and/or staged correction. Further evidence is needed for optimal management.

The present study examined metabolites in Northern wild rice (WLD), the impact of WLD supplemented high fat (HF) diet on gut microbiota, short chain fatty acids (SCFAs) and correlation with metabolism or inflammation versus HF+white rice (WHR) in mice. C57BL/6J mice received HF diet supplemented with 26g% WHR, 26g% WLD, or 13g% WHR+13g% WLD (WTWD) for 12 weeks. The levels of fasting plasma glucose, total cholesterol, triglycerides, insulin resistance, inflammatory cytokines and monocyte adhesion were lower, and the abundances of fecal Lactobacillus gasseri species bacteria and propionic acid were higher in HF+WLD diet-fed mice compared to HF+WHR diet-fed mice (p<0.05). The anti-inflammatory effects of HF+WTWD diet were weaker than that in HF+WLD diet, but were greater than that in HF+WHR diet-fed mice (p<0.05). Relative abundances of fecal Lactobacillus gasseri and propionic acid in HF+WLD fed-mice were higher than that in HF+WHR fed mice. The abundance of fecal L. gasseri and propionic acid negatively correlated with metabolic and inflammatory markers (p<0.05). The findings suggest that WLD dose-dependently attenuated metabolic and inflammatory disorders in HF diet-fed mice. Interactions between WLD components and gut microbiota may upregulate fecal propionic acid and contribute to metabolic and anti-inflammatory benefits of WLD diet-induced insulin resistant mice.

Hubble diagrams are examined for SN1a supernovae in the redshift range z = 0.01–1.3 and for gamma ray bursts in the range z = 0.034–8.1. It is shown that in the low redshift range, the Hubble diagram shows an innate equivocality between the ΛCDM and the tired light model. This means that the strong agreement between the z/µ data, calculated with the parameters of the ΛCDM model, and the experimentally measured z/µ values cannot be considered as definite evidence for the expansion hypothesis. The exponential function , which is characteristic of the tired light redshift mechanism, fits the data with similarly high accuracy. Hence, on the premise of low redshift data, a decision for or against either model is completely arbitrary. The Hubble diagram for high redshift gamma ray bursts shows poor agreement with the ΛCDM model, but concurs with the exponential energy decay following from the tired light redshift hypothesis.

The endothelium plays a key role in blood vessel health. At the interface of the blood, it releases several mediators that regulate local processes and that protect against the development of cardiovascular disease. In this interplay, there is increasing evidence for a role of extracellular nucleotides and endothelial purinergic P2Y receptors (P2Y-R) in vascular protection. Recent advances have revealed that endothelial P2Y1-R and P2Y2-R mediate nitric oxide-dependent vasorelaxation as well as endothelial cell proliferation and migration, which are processes involved in the regeneration of damaged endothelium. However, endothelial P2Y2-R, and possibly P2Y1-R, have also been reported to promote vascular inflammation and atheroma development in mouse models, with endothelial P2Y2-R also being described as promoting vascular remodeling and neointimal hyperplasia. Interestingly, at the interface with lipid metabolism, P2Y12-R has been found to trigger HDL transcytosis through endothelial cells, a process known to be protective against lipid deposition in the vascular wall. Better characterization of the role of purinergic P2Y-R and downstream signaling pathways in determination of the endothelial cell phenotype in healthy and pathological environments has clinical potential for the prevention and treatment of cardiovascular diseases.

The western Sulige gas field is a new and key reserve area for the rolling development of the Sulige gas field in China. However, due to the complex gas–water relationship and the difficulty in identifying gas and water formation, the scale and benefit deployment of the gas field are seriously restricted. In particular, almost all of the wells in the area produce water and no water measurement has been carried out for any single well, which leads to an unclear understanding of the dynamic characteristics of the production wells, thus affecting the productivity calculations of the gas wells and the overall regional productivity evaluation. Based on the testing data for a gas well, the impacts of the reservoir property parameters on the gas and water production were analyzed by combining the production performance and static geological characteristics. It was determined that the physical parameters K, Kh, and φSg had good positive correlations with gas production but not with water production; thus, effective prediction cannot be obtained for water production in gas well testing. After the analysis of the liquid loading law, the gas wells were classified into three types: continuous liquid carrying production, slight liquid loading, and liquid loading wells. In general, up to 96% of the gas wells were liquid loaded. According to the different production performances exhibited in the different stages of the gas wells, five types of methods for diagnosing water production wells were proposed (gas testing, pilot production, gas–liquid two-phase measurement testing, liquid level detection, and production performance analysis), as well as the diagnostic criteria and corresponding solutions. To obtain real-time water production data for each well and investigate the change of water-gas ratio (WGR) during the whole production process, a water production splitting method for gas wells based on three-dimensional geological modeling and numerical simulation combined with the constraints of the total water production of gas gathering stations was explored and established. The splitting results can be used to evaluate the water and gas productivity of gas wells and determine the best deliquification period. The gas well productivity when water production was considered was about 10% lower than that when water production was not considered. The best deliquification period was determined to be 125 days for wells with small water production, 20 days for wells with moderate water production, and 3 days for wells with serious water production. The results of this study could provide technical support for the scientific evaluation of gas well production indicators, reduction of development costs, and improvement of oil recovery.

Oxidative stress is one of the primary instigators of the onset of various human ailments, including cancers, cardiovascular diseases, and dementia. Particularly, oxidative stress has a severe effect on low-density lipoprotein (LDL) oxidation, leading to several detrimental health effects. Thereof, in this study, the effect of beeswax alcohol (BWA) was evaluated to prevent LDL oxidation, enhancement of paraoxonase 1 (PON-1) activity of high-density lipoprotein (HDL), and zebrafish embryo survivability. Furthermore, the implication of BWA consumption on the oxidative plasma variables was assessed by a preliminary clinical study on middle and older human subjects (n=50). Results support BWA augmentation of PON-1 activity in a dose-dependent manner (10-30 μM), which was significantly better them the effect exerted by coenzyme Q10 (CoQ10). Moreover, BWA significantly curtails CuSO4 (final 0.5 μM) evoked LDL/apo-B oxidation and a marked reduction of lipid peroxidation in LDL. The transmission electron microscopy (TEM) analysis revealed a healing effect of BWA towards the restoration of LDL morphology and size impaired by the exposure of Cu2+ ions (final 0.5 μM). Additionally, BWA counter carboxymethyllysine (CML, 500 ng) induced toxicity and rescued zebrafish embryos from development deformities and apoptotic cell death. A completely randomized, double-blind, placebo-controlled preliminary clinical study on middle and older-aged human subjects (n=50) exhibited that 12 weeks of BWA (100 mg/day) supplementation efficiently diminished serum malondialdehyde (MDA), total hydroperoxides, and enhanced total antioxidant status by 25%, 27%, and 22%, respectively, compared to the placebo control and baseline values. Furthermore, the consumption of BWA did not exhibit any noteworthy changes in anthropometric profile, lipid profile, glucose levels, and biomarkers pertinent to kidney and liver function, thus confirming the safety of BWA for consumption. Conclusively, BWA prevents LDL oxidation, enhances PON-1 activity in HDL, and has a positive impact on the oxidative variables of human subjects.

Lung cancer is the leading cause of global cancer-related mortality resulting in ~1.8 million deaths annually. Systemic, molecular targeted, and immune therapies have provided significant improvements of survival outcomes for patients. However, drug resistance usually arises and there is an urgent need for novel therapy screening and personalized medicine. 3D patient-derived organoid (PDO) models have emerged as a more effective and efficient alternative for ex vivo drug screening than 2D cell culture and patient-derived xenograft (PDX) models. In this review, we performed an extensive search of lung cancer PDO-based ex vivo drug screening studies. Lung cancer PDOs were successfully established from fresh or biobanked sections/biopsy of lung tumors, PDXs, and pleural affusion. PDOs were subject to ex vivo drug screening with chemotherapy, targeted therapy and immune therapy agents. PDOs mainly recapitulated the genomic alterations, transcriptomic landscape and drug sensitivity of primary tumors. Although sample sizes of the previous studies were limited and some technical challenges remained, PDOs showed promise to screen novel therapy drugs. With the technical advance of high throughput, tumor-on-chip, combined microenvironment, and air-liquid interface (ALI), the drug screening using PDOs would serve better for precision care of lung cancer patients.

In the evolving landscape of pharmaceutical manufacturing, a comprehensive continuous production process is being crafted for small-scale active pharmaceutical ingredient production. This study focuses on continuous crystallization with separate nucleation and crystal growth units, as well as continuous downstream processing, encompassing filtration, washing, and drying until the formation of free-flowing particles. We introduce a novel continuous nucleator designed based on solubility data and produced via 3D printing, enabling a fast and precise small-scale manufacturing of a nucleator meeting the requirements for nucleation and for the further growth processes. The nucleator was evaluated with regard to its suitability for continuous long-term operation across various coupled crystallizers. As a practical application example it is connected to a slug flow crystallizer to enable high-quality continuous crystallization. Additionally, the full integration of downstream processes using the continuous vacuum screw filter to achieve free-flowing product particles is realized. Even under non-optimized process conditions, with the help of in-situ generation of nuclei free-flowing product particles were successfully obtained. This is particularly useful during drug development when no material is available for seed addition and quickly obtain product for further characterization.

Daily vitamin D supplementation using higher than normal dosing (up to the upper limit, UL) and intermittent (once or twice per week) dosing were studied in patients with increased risk of vitamin D deficiency. Using a PubMed database an adequate search for published randomized control trials and other studies was done and results were analyzed. This review provides overview of use of 7000 IU daily, 30,000 IU per week or twice weekly and 50,000 IU weekly of vitamin D on rapid restore of 25(OH)D concentrations to at least 30 ng/mL in different groups of patients at high risk of vitamin D deficiency. The above mention dosing should be considered in adults with obesity or multi-diseased patients on requiring multi-treatment with the use of several drugs, including drugs affecting vitamin D metabolism. The simple schedule for 7000 IU/day, 30,000 IU/week or twice weekly or 50,000 IU/week, all for 6-8 weeks of use by patients representing the increased risk of vitamin D deficiency were provided for consideration. It appeared that higher daily doses or intermittent doses suggested above are effective, safe and responsive for patient’s preferences.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

Intended for the high voltage gain and wide-range operation of DC/DC converters for photovoltaic energy storage systems, a topology for four-phase interleaved DC/DC converters for photovoltaic power generation is proposed. This topology increases output voltage for output in series, and reduces the input current ripple by paralleling the input. Compared with traditional boost converter topology, the proposed topology reduces the output current and output voltage ripple, reduces the stress of the switching device, and reduces the withstanding voltage of the output capacitor under the premise of ensuring the boost ratio. Experimental results show that the maximum efficiency of the converter reaches 95.37%. Compared with traditional boost converters, the proposed converter offers obvious advantages in efficiency under the conditions that the output voltage and load are variable.

For the first time, few-layer graphene (FLG) nanosheets were synthesized by the method of self-propagating high-temperature synthesis (SHS) from biopolymers (starch and lignin). We suggested that biopolymers (lignin, tree bark) and polysaccharides, in particular starch, could be an acceptable source of native cycles for the SHS process. The carbonization of biopolymers under the conditions of the SHS process was chosen as the basic method of synthesis. Chemical reactions, under the conditions of the SHS process, proceed according to a specific mechanism of nonsothermal branched-chain processes, which are characterized by the joint action of two fundamentally different process-accelerating factors - avalanche reproduction of active intermediate particles and self-heating. The method of obtaining FLG nanosheets included the thermal destruction of hydrocarbons in a mixture with an oxidizing agent. We used biopolymers as hydrocarbons and ammonium nitrate as an oxidizing agent. Thermal destruction was carried out in the mode of SHS, heating the mixture in a vessel at a speed of 20–30 oC/min to 150-200 oC and keeping at this temperature for 15–20 min with the discharge of excess gases into atmosphere. A combination of spectrometric research methods, supplemented by electron microscopy data, has shown that the particles of the carbonated product powder in their morphometric and physical parameters correspond to FLG nanosheets. An X-ray diffraction analysis of the indicated FLG nanosheets was carried out, which showed the absence of formations with a graphite crystal structure in the final material. The surface morphology was also studied and the features of the IR absorption of FLG nanosheets were analyzed. It is shown that the developed SHS method makes it possible to obtain FLG nanosheets with linear dimensions of tens of microns and a thickness of not more than 1-5 graphene layers (several graphene layers).

The increased demand for resources and energy that is developing with rising global consumption represents a key challenge for our generation. Biogas production can contribute to sustainable energy production and closing nutrient cycles using organic residues or as part of a utilization cascade in the case of energy crops. Compared to hydrogen (H2), biogas with a high methane (CH4) content can be fed into the gas grid without restrictions. For this purpose, the CH4 content of the biogas must be increased from 52 to 60 % after anaerobic digestion to more than 96 %. In this study, biological hydrogen methanation (BHM) in trickling-bed reactors (TBR) is used to upgrade biogas. Design of experiments (DoE) is used to determine the optimal process parameters. The performance of the reactors is stable under all given conditions, reaching a “low” gas grid quality of over 90 %. The highest CH4 content of 95.626 ± 0.563 % is achieved at 55 °C and 4 bar, with a methane formation rate (MFR) of 5.111 ± 0.167 m³/(m³·d). The process performance is highly dependent on the H2:CO2 ratio in the educts, which should be as close as possible to the stochiometric ratio of 4. In conclusion, BHM is a viable approach to upgrade biogas to biomethane quality and can contribute to a sustainable energy grid.

The Lewis basicity of selected organic bases, modeled by the enthalpies of adduct formation between gaseous BF3 and the bases in dichloromethane (DCM) solution, is critically examined. Although experimental enthalpies for a large number of molecules have been reported in the literature, it may be desirable to estimate missing or uncertain data for important Lewis bases. We have decided to use high-level ab initio procedures, combined with a polarized continuum solvation model, in which the solvated species are the clusters formed by specific hydrogen bonding of DCM with the Lewis base and the Lewis base/BF3 adduct. This mode of interaction with DCM corresponds to a specific solvation model (SSM). The results actually show that the enthalpy of BF3 adduct formation in DCM solution is clearly influenced by specific interactions, DCM acting as hydrogen-bonding donor (HBD) molecule in two ways: base/DCM and adduct/DCM, confirming that specific solvation is an important contribution to experimentally determined Lewis basicity scales. This analysis allows us to conclude that there are reasons to suspect some gas-phase values to be in error by more than the stated experimental uncertainty. Some experimental values in DCM solution that were uncertain because of identified reasons can be complemented by the computed values.

Conventional radiation therapy uses white X-rays that consist of a mixture of X-ray waves with various energy levels. In contrast, a monochromatic X-ray (monoenergetic X-ray) has a single energy level. Irradiation of high Z elements with a synchrotron generated monochromatic X-ray with the energy at or higher than the K-edge energy of the element results in the production of the Auger electrons that cause DNA damage leading to cell killing. Delivery of high Z elements into cancer cells and tumor mass can be facilitated by the use of nanoparticles. Mesoporous silica nanoparticles (MSNs) have been shown to be effective in delivering high Z elements to cancer cells. A proof of principle experiment was reported that demonstrated the feasibility of this approach. This opens up a possibility to pursue the Auger cancer therapy by the combined use of MSNs loaded with high Z elements and monochromatic X-rays. Similar cancer therapies using other types of quantum beams such as neutron, proton and carbon ion beams can be envisioned.

In this paper we describe a nonparametric maximum likelihood (NPML) method for estimating multivariate mixing distributions. Given $N$ independent observations, convexity theory shows that the NPML estimator is discrete with at most $N$ support points. The original infinite NPML problem then becomes the finite dimensional problem of finding the location and probability of the support points. The probability of the support points is found by a Primal-Dual Interior-Point method; the location of the support points is found by an Adaptive Grid method. Our method is able to handle high-dimensional and complex multivariate mixture models.An important application is discussed for the problem of population pharmacokinetics and a non-trivial example is treated.Our algorithm has been successfully applied in hundreds of published pharmacometric studies. In addition to population pharmacokinetics, this research also applies to empirical Bayes estimation and many other areas of applied mathematics.

The group III two-component hybrid histidine kinase MoHik1p in the filamentous fungus Magnaporthe oryzae is known to be a sensor for external osmotic stress and essential for the fungicidal activity of the phenylpyrrole fludioxonil. The mode of action of fludioxonil has not yet been completely clarified but rather assumed to hyperactivate the high osmolarity glycerol (HOG) signaling pathway. To date, not much is known about the detailed molecular mechanism of how osmotic stress is detected or fungicidal activity is initiated within the HOG pathway. The molecular mechanism of signaling was studied using a mutant strain in which the HisKA signaling domain was modified by an amino acid change of histidine H736 to alanine A736. We found that MoHik1pH736A is as resistant to fludioxonil but not as sensitive to osmotic stress as the null mutant ∆Mohik1. H736 is required for fludioxonil action but is not essential for sensing sorbitol stress. Consequently, this report provides evidence of the difference in the molecular mechanism of fludioxonil action and the perception of osmotic stress. This is an excellent basis to understand the successful phenylpyrrole-fungicides’ mode of action better and will give new ideas to decipher cellular signaling mechanisms.

The emergence of antimicrobial resistance (AMR) Candida auris presents a formidable global health challenge, causing severe healthcare-associated infections with high mortality rates. Its ability to colonize surfaces and resist standard disinfectants undermines traditional hygiene practices, prompting an urgent need for novel strategies. Ultraviolet C (UVC) light offers a promising approach due to its rapid and broad-spectrum germicidal efficacy. This review comprehensively examines the current knowledge of UVC LED technology in combating C. auris, highlighting its effectiveness, limitations, and potential applications in healthcare hygiene. UVC light has potent activity against C. auris, including multidrug-resistant (MDR) strains. UVC can reduce C. auris on contaminated surfaces, aiding in transmission prevention. This review explores implementation strategies, including mobile UVC systems for targeted disinfection of high-risk areas and equipment, integration into air handling units (AHUs) to continuously disinfect recirculating air, and incorporation into water treatment systems. Current limitations in our understanding of UVC safety and effectiveness necessitate further research to optimize application protocols and ensure treatment safety while maintaining efficacy against C. auris. Integrating UVC disinfection technology into infection control programs holds promise for strengthening hygiene practices that will curb the global spread of C. auris and improve patient outcomes.

Indonesia's SUMBAGUT 150 kV transmission of High Voltage Alternating Current Network (HVAC) system has considerable power losses. These power losses are a critical problem in the transmission network system. Meanwhile, this study provides one solution to reduce power losses using a High Voltage Direct Current (HVDC) network system. Determining the location to convert HVAC into HVDC is very important. The authors use Particle Swarm Optimization (PSO) to get the optimal location on the 150 kV SUMBAGUT HVAC transmission network system. The study results showed that before using the HVDC network system, the power losses were 122.26 MW. Meanwhile, power losses with one transmission HVDC in the "Paya Pasir-Sei Rotan" are 84.16 MW, "Porsa-P. Siantar" 90.83 MW, "Paya Pasir-Paya Geli" 104.14 MW. Then power losses with two transmission HVDC in "Paya Pasir-Sei Rattan" and "Porsa-P. Siantar" is 71.24 MW, "Paya Pasir-Sei Rotan" and "Paya Pasir-Paya Geli" 77.46 MW, "Porsa-P. Siantar" and "Paya Pasir-Paya Geli" 78.52 MW. The last result, power losses with three transmission HVDC in "Paya Pasir-Sei Rotan," "Porsa-P. Siantar," and "Paya Pasir-Paya Geli" lost 64.57 MW.

This study analyses some of the leading technologies for the construction and configuration of IT infrastructures to provide services to users. For modern applications, guaranteeing service continuity even in very high computational load or network problems is essential. Our configuration has among the main objectives of being highly available (HA) and horizontally scalable, that is, able to increase the computational resources that can be delivered when needed and reduce them when they are no longer necessary. Various architectural possibilities are analysed, and the central schemes used to tackle problems of this type are also described in terms of disaster recovery. The benefits offered by virtualisation technologies are highlighted and are bought with modern techniques for managing Docker containers that will be used to build the back-end of a sample infrastructure related to a use-case we have developed. In addition to this, an in-depth analysis is reported on the central autoscaling policies that can help manage high loads of requests from users to the services provided by the infrastructure. The results we have presented show an average response time of 21.7 milliseconds with a standard deviation of 76.3 milliseconds showing excellent responsiveness. Some peaks are associated with high-stress events for the infrastructure, but the response time does not exceed 2 seconds even in this case. The results of the considered use case studied for nine months are presented and discussed. In the study period, we improved the back-end configuration and defined the main metrics to deploy the web application efficiently.

Increasing salt intake has substantial negative impacts on health and well-being. This review article focusses on the effect of salinity intrusion (SI) on the water quality and community health of coastal Bangladesh and to find out the effectiveness of interventions for reducing the negative effects of salinity. Saline water is a noteworthy reason for hypertension or high blood pressure in the coastal areas. Health status of women especially the pregnant women are vulnerable because of drinking water sodium (DWS) prompting to pre-eclampsia, high blood pressure and hypertension as well as infant mortality. Several interventions such as rainwater harvesting and Pond sand filter (PSF) system as well as managed aquifer recharge (MAR) usage and the integration of mixed sources were reviewed on the content of drinking water sodium (DWS). Although rainwater has the positive impact of low or no sodium intake on human health, it still possesses negative impacts from not having vital minerals. Despite what might be expected, in MAR a steady increment in sodium concentration through the span of the dry season was observed. It is, subsequently, important to increase awareness about drinking water sodium (DWS) intake by providing and adopting correct technological interventions.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Cancer stem cells remain a challenge to isolate and characterize because of their plastic phenotype. Using a microfluidic lab-on-a-chip based on ultra-high frequency dielectophoresis, we measured the electromagnetic signature of colorectal cancer cells and demonstrated that cancer stem cells show a distinct and lower electromagnetic signature than differentiated cells. The release of extracellular vesicles from tumor cells can drive tumor progression and metastasis development. As extracellular vesicles from cancer stem cells carry more aggressive content, we treated colorectal cancer cells with these vesicles to test whether the lab-on-a-chip can detect a change in phenotype. The electromagnetic signature of treated cells is modified in comparison to untreated cells and sometimes even when no biological change is observed. The lab-on-a-chip provides rapid and relevant result without prior labeling compared to conventional biological approaches. It could be useful in the clinic for early detection of cancer stem cells in the tumor mass and for monitoring the aggressive potential of extracellular vesicles in the bloodstream in order to adapt therapeutic management and prevent relapse.

Physics-informed neural networks are a promising method to yield surrogate models of flow fields. We present a metamodeling technique for variable geometries based on physics-informed neural networks. The method was applied to the DU99W350 airfoil at a Reynolds number of 1×10⁵. The model predicted the Reynolds-averaged velocity and pressure field around the airfoil for arbitrary angles of attack between 10.0° and 17.5°. The model was trained with data from CFD simulations for a limited set of angles of attack. Additionally, satisfaction of the a priori known boundary conditions as well as the Reynolds-averaged Navier-Stokes equations were trained. A sensitivity analysis concerning the Reynolds number, the amount and distribution of training data, and the turbulence model was conducted showing the superiority of the pseudo-Reynolds stress method and the demand of labeled training data in the domain. The trained network was capable of predicting the developing flow separation on the suction surface and exhibited excellent agreement with CFD results even in the proximity to the wall for interpolations as well as extrapolations from the labeled data set.

Lipophilicity can be measured with different methods, such as Shake-Flask or liquid chromatography. HPLC presents the advantage of overcoming solubility issues and therefore extending the range of lipophilicity to high values. A specific HPLC method, called ELogD, had been developed 20 years ago on a C₁₆-amide stationary phase, enhancing hydrophobic and hydrogen bond interactions to mimic octanol-water partition. The emergence of novel stationary phases added to the need for a less complex mobile phase has led to the development of a new HPLC assay called alphaLogD, applicable to neutral and basic compounds at pH 7.4, that combines superficially porous particles, a high number of equilibriums between solutes and stationary phase, and results in a lower number of isocratic methods to determine the logk’_w at a higher throughput. Statistical studies have been run to successfully evaluate the alphaLogD method compared to the Shake-Flask method and to allow this lipophilicity measurement into the so-called Beyond-Rule-of-5-molecules space.

Some time ago, Kobayashi et al. experimentally studied the so-called Lee-Naughton-Lebed's (LNL) angular effect in strong electric fields [K. Kobayashi, M. Saito, E. Omichi, and T. Osada, Phys. Rev. Lett. \textbf{96}, 126601 (2006)]. They found that strong electric fields split the LNL conductivity maxima in $\alpha$-(ET)$_2$-based organic conductor and hypothetically introduced the corresponding equation for conductivity. In this Letter, for the first time we suggest quantum mechanical theory of the LNL angular oscillations in moderately strong electric fields. In particular, we demonstrate that the obtained by us approximate theoretical formula coincides with the hypothetical one and well describes the above mentioned experiments.

The dependence of the critical temperature $T_c$ of high-temperature superconductors of various families on their composition and structure is proposed. A clear dependence of the critical temperature of high-temperature superconductors (hydrides, Hg- and Y-based cuprates) on the serial number of the constituent elements, their valence and crystal lattice structure has been revealed. For cuprates, it is shown that it is possible to obtain even higher temperatures of superconducting transitions at normal pressure by implanting mercury atoms into the crystal lattice of cuprate.

The oral cavity harbors hundreds of microbial species that are present either as planktonic cells, or incorporated into biofilms. The majority of the oral microbes are commensal organisms. Those that are pathogenic microbes can result in oral infections, and at times initiate systemic diseases. Biofilms that contain pathogens have been challenging to control. Many conventional antimicrobials have proven to be ineffective. Recent advances in science and technology are providing new approaches for pathogen control and containment and methods to characterize biofilms. This perspective provides: 1) A general understanding of biofilm development; 2) A description of emerging chemical and biological methods to control oral biofilms; 3) An overview of high-throughput analytical approaches to analyze biofilms.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

Although many policosanols from different sources, such as sugar cane, rice bran, and insects, have been marketed worldwide, there has been no comparative study of the in vivo efficacy using a hyperlipidemic animal model. This study compared the efficacy of treating dyslipidemia with four different policosanols, including one sugar cane wax alcohol from Cuba (Raydel®) and three policosanols from China (Xi’an Natural sugar cane, Xi’an Realin sugar cane, and Shaanxi rice bran) in hyperlipidemic zebrafish. After 12 weeks of consumption of each policosanol (final 0.1% in diet, wt/wt) and high cholesterol diet (HCD, final 4%, wt/wt) in a tetrabit, the Raydel policosanol group and Xi’an Natural policosanol group showed the highest survivability of approximately 81%, whereas the Xi’an Realin policosanol group and Shaanxi policosanol group showed 57% and 67% survivability, respectively. Among five HCD groups, the Raydel policosanol group showed the lowest serum total cholesterol (TC, p<0.001 versus HCD control) and triglyceride (TG, p<0.001 versus HCD control) with the highest percentage of high-density lipoproteins (HDL)-C in TC. The Raydel policosanol group also showed the lowest serum aspartate aminotransferase (AST) and alanine aminotransferase (ALT) levels with the least infiltration of inflammatory cells and interleukin-6 production in hepatocytes. In the ovary, the Raydel policosanol group also showed the highest contents of mature vitellogenic oocytes with the lowest production of reactive oxygen species and cellular apoptosis in ovarian cells. In the testis, the Raydel policosanol group also showed the healthiest morphology for spermatogenesis with the least interstitial area and reactive oxygen species (ROS) production in testicular cells. In conclusion, 12 weeks of Raydel policosanol consumption resulted in remarkable improvement of the blood lipid profile, amelioration of inflammation in the liver, and enhancement of the cell morphology in the ovary and testis with the highest survivability under the HCD.

With the existence of several programming languages such as C/C++, Java, C#, LISP, Prolog, Python, Simula, F#, Go, Haskell, Scala, Ruby, Dart, Swift, Groovy etc. and diverse paradigms like structured, object-oriented, list, aspect-oriented, service-oriented, web, mobile and logic programming, there is a need to perform an exhaustive comparative analysis of diverse compilers and environments before making a choice of implementation technology in software engineering. Optimization of compilers helps to reduce execution time by making use of high speed processor registers, thereby, eliminating redundant computation. This paper reports some series of performance analysis done with some popular programming languages including Java, C++, Python and PHP. Programs involving recursive and iterative functions like factorial of large numbers and binary search of large arrays were run on the various platforms with the execution time recorded in milliseconds and represented in a chart. This can aid in making a selection of the appropriate language to use for a given application domain.

In this work we looked for a stable and accurate procedure to perform feature selection in datasets with a much higher number of predictors than individuals, as in Genome-Wide Association Studies. Due to the instability in feature selection when many potential predictors are measured, a variable selection procedure is proposed that combines several replications of shrinkage regression models. A weighted formulation is used to define the final predictors. The procedure is applied to investigate Single Nucleotide Polymorphisms (SNPs) predictors associated to Alzheimer’s disease in the Alzheimer’s disease Neuroimaging Initiative (ADNI) dataset. Two data scenarios are investigated: one considering only the set of SNPs and another with the covariates age, sex, educational level and APOE4 genotype. The SNP rs2075650 and the APOE4 genotype are given as risk factors for AD, which is in line with the literature, and other four new SNPs are pointed, opening new hypotheses for in vivo analyses. These experiments demonstrate the potential of the new method for stable feature selection.

When water molecules or other particles collide with protein molecules in a solution, the protein molecules absorb some of the momentum and deform, forming a certain molecular potential energy. When a protein molecule in a high-energy state changes to a stable state, if there is a suitable substrate binding and the potential energy of the protein molecule is greater than the energy required to break the substrate chemical bond, catalytic action will occur. The α-helices and β-folds in protein molecules play a major role in converting the kinetic energy of water molecules into their own potential energy due to the large number of amino acids involved and their regular structure. The internal structural deformation of proteins caused by the impact of water molecules on α-helices and β-folds also has a profound impact on the structure of substrates. ‌

Advanced lithography requires highly sensitive photoresists to improve lithographic efficiency, and it is critical yet challenging to develop high-sensitivity photoresists and imaging strategies. Here, we report a novel strategy for ultra-high sensitivity using hexafluoroisopropanol (HFIP)-containing fluoropolymer photoresists. The incorporation of HFIP, with its strong electrophilic property and electron-withdrawing effect of the fluorine atoms, significantly increases the acidity of the photoresist after exposure, enabling imaging without conventional photoacid generators (PAGs). The HFIP-containing photoresist has been evaluated by electron beam lithography to achieve a trench of ~40 nm at an extremely low dose of 3 μC/cm2, which shows sensitivity enhancement by ~10 times to the commercial PAGs involved system, revealing its high-sensitivity and high-resolution features. Our results demonstrate a new type of PAGs and a novel approach to higher-performance imaging beyond conventional photoresist performance tuning.

Background of the Study: We investigated the link between hypertension and cancer since it has been suggested that hypertension may raise the long-term risk of cancer. Previous large observational cohort studies found that greater blood pressure (BP) was related to a higher risk of cancer. Mendelian randomization (MR) was utilized to produce less confounded blood pressure estimates (BP) on overall and site-specific malignancies. The study aims to draw conclusions on the relationship between high blood pressure and cancer. Methods: Studies on high blood pressure and various malignancies are inconclusive, except for renal cell carcinoma. However, given that most meta-analyses only contained a limited number of trials, some relative risks had small to moderate magnitudes, and several may have been impacted by residual confounding, careful interpretation is necessary. The study was conducted using the meta-analysis technique. Cochran's Q test and I2 test were used to assess statistical heterogeneity between studies in the current investigation for research involving two or more cause and outcome combinations. Results: Positive correlations were also reported between high blood pressure and esophageal adenocarcinoma, squamous cell carcinoma, liver, and squamous cell carcinoma. However, most studies lacked multivariable adjustments. Physical and numerical risk of cardiovascular disease is linked to bowel cancer but no other cancers. According to a meta-analysis, hypertensive persons could also be at increased danger of gastrointestinal and breast cancer. Most meta-analyses comprised several trials with moderate or mild hazard ratios.ConclusionDifferent types of cancers have been noted to be directly caused by hypertension. In addition, some treatments have also been associated with the side effects of cancer treatments to cause hypertension. Women facing hypertension have an increased risk of getting breast cancer. Although some cancers showed a real relationship with hypertension, others had no connection at all.

Soliton crystal micro-combs are powerful tools as sources of multiple wavelength channels for radio frequency (RF) signal processing. They offer a compact device footprint, large numbers of wavelengths, very high versatility, and wide Nyquist bandwidths. Here, we demonstrate integral order RF signal processing functions based on a soliton crystal micro-comb, including a Hilbert transformer and first- to third-order differentiators. We compare and contrast results achieved and the tradeoffs involved with varying comb spacing, tap design methods, as well as shaping methods.

We demonstrate an RF photonic fractional Hilbert transformer based on an integrated Kerr micro-comb source featuring a record low free spectral range of 49 GHz. By programming and shaping the comb lines according to calculated tap weights for up to 39 wavelengths across the C-band, we achieve tunable bandwidths ranging from 1.2 to 15.3 GHz as well as variable center frequencies from baseband to 9.5 GHz, for both standard integral and arbitrary fractional orders. We experimentally characterize the RF amplitude and phase response of the tunable bandpass and lowpass Hilbert transformers with 90 and 45-degree phase shifts. The experimental results show good agreement with theory, confirming the effectiveness of our approach as a powerful way to implement standard and fractional order Hilbert transformers with broad and variable bandwidths and center frequencies, with high reconfigurability and greatly reduced size and complexity. Tan, and D. J. Moss are with the Optical Sciences Centre, Swinburne University of Technology, Hawthorn, VIC 3122, Australia. (Corresponding e-mail: [email protected]). Xu is with the Electro-Photonics Laboratory, Department of Electrical and Computer System Engineering, Monash University, Clayton, 3800 VIC, Australia

The MAGIC (Major Atmospheric Gamma-ray Imaging Cherenkov) Florian Goebel telescopes are a system of two Cherenkov telescopes located on the Canary island of La Palma (Spain), at the Roque de Los Muchachos Observatory, and operating in stereo mode since 2009. Their low energy threshold (reaching 15 GeV) allows the study of Active Galactic Nuclei (AGNs) in the very-high-energy gamma ray range with an impressive sensitivity up to the redshift limit of the existing IACT systems. MAGIC has collected many discoveries and comprehensive studies of different kinds of galaxies and their AGNs, also in a multi-wavelength context, expanding the knowledge of our Universe. Here we report the highlights which have been achieved by the MAGIC collaboration since the beginning of the operations.

Southern highbush blueberry plantations have been expanded into worldwide non-traditional growing areas with elite cultivars and improved horticultural practices. This article presents a comprehensive review of current production systems – alternatives to traditional open field production – such as production in protected environments, high-density plantings, evergreen production, and container-based production. We discuss the advantages and disadvantages of each system and compare their differences to the open field production. In addition, potential solutions have been provided for some of the disadvantages. We also highlight some of the gaps existing between academic studies and production in industry, providing a guide for future academic research. All these alternative systems have shown the potential to produce high yields with high quality berries. Alternative systems, compared to the field production, require higher establishment investments and thus create an entry barrier for new producers. Nevertheless, with their advantages, alternative productions have potential to be profitable.

Populations with essential hypertension have a high risk of nonalcoholic steatohepatitis (NASH). In this study, we investigated the mechanism that underlies the progression of hypertension-associated NASH by comparing differences in the development of high fat and cholesterol (HFC) diet-induced NASH among three strains of rats, i.e., two hypertensive strains comprising spontaneously hypertensive rats and the stroke-prone spontaneously hypertensive 5/Dmcr, and the original Wistar Kyoto rats as the normotensive control. We investigated histopathological changes and molecular signals related to inflammation in the liver after feeding with the HFC diet for 8 weeks. The diet induced severe lobular inflammation and fibrosis in the livers of the hypertensive rats, whereas it only caused mild steatohepatitis in the normotensive rats. Increased activation of proinflammatory signaling (transforming growth factor-β1/mitogen-activated protein kinases pathway) was observed in the hypertensive strains fed with the HFC diet. In addition, the HFC diet suppressed the nuclear factor erythroid 2-related factor 2 pathway in the hypertensive rats and led to lower increases in the hepatic expression of heme oxygenase-1, which has anti-oxidative and anti-inflammatory activities. In conclusion, these signaling pathways might play crucial roles in the development of hypertension-associated NASH.

The DEP force is usually calculated from the object’s point of view using the interaction of the object’s induced dipole moment with the inducing field. Recently, we described the DEP behavior of high- and low-conductive 200-µm 2D spheres in a square 1x1mm chamber with a plane-versus-plane electrode configuration from the system’s point of view. Here we extend our previous considerations to the plane-versus-plane and pointed-versus-pointed electrode configurations. The trajectories of the sphere center and the corresponding DEP forces were calculated from the gradient of the system’s overall energy dissipation for given starting points. The dissipation’s dependence on the sphere’s position in the chamber is described by the numerical “conductance field”, which is the DC equivalent of the capacitive charge-work field. While the plane-versus-plane electrode configuration is field-gradient free without an object, the presence of the highly or low-conductive spheres generates structures in the conductance fields, which result in very similar DEP trajectories. For both electrode configurations, the model describes trajectories with multiple endpoints, watersheds, and saddle points, very high attractive and repulsive forces in front of pointed electrodes, and the effect of mirror charges. Because the model accounts for inhomogeneous polarization within the objects, the approach allows the modeling of the complicated interplay of attractive and repulsive forces near electrode surfaces and chamber edges. Non-reversible DEP forces or asymmetric magnitudes for the highly and low-conductive spheres in large areas of the chamber indicate the presence of higher-order moments, mirror charges, etc.

We report a case of colloid carcinoma (CC) arising from an intestinal-type intraductal papillary mucinous neoplasm with high-grade dysplasia (IPMNHGD) of the pancreas, diagnosed with serial pancreatic juice aspiration cytological examination (SPACE). A rapidly growing intraductal papillary mucinous neoplasm (IPMN) in a 71-year-old Japanese man accelerated his hospitalization in our institute. Clinically, a large, ruptured pancreatic cyst was suspected. Cytologically, several mucin-positive signet-ring cells were scattered in the inflammatory, necrotic, or mucinous background. Signet-ring cells in cell block specimens were immunoreactive for MUC2, MUC5AC, maspin, S100P, and claudin-18. The final cytologic diagnosis was CC arising in an intestinal-type IPMNHGD with intraperitoneal penetration. The patient died two months postoperatively. The cytologic diagnosis was achieved through SPACE, and the presence of signet-ring cells was characteristic. Anti-claudin-18.2-specific monoclonal antibody therapy will likely be used to treat patients with IPMNHGD in the future. To our knowledge, this is the first report in English on mucin-positive signet-ring cells of CC arising in an intestinal-type IPMNHGD evaluated by SPACE cytology.

Glioblastoma is a highly aggressive brain tumor and is considered to be the most common primary one. Recurrence after treatment is a major problem. The recurrence of GBM is related to different cellular mechanisms and molecular signaling. Therapies to prolong survival are not completely effective. Epigenetics and non-coding genetic elements play a crucial role in gliomagenesis. Non-coding RNAs are novel regulatory RNAs that play key roles in different physiological processes such as gene regulation, cell differentiation, and proliferation. Interestingly, some LncRNAs have a tumor suppressor role while others are oncogenic. In this review article, we are going to illustrate the role of a well-known lncRNA HOX transcript antisense intergenic RNA (HOTAIR) in glioma and highlight the possible functions in glioma in both pre-clinical and clinically evident studies.

In this letter, we propose a pattern-diversity antenna with different radiation patterns at two different frequency bands (f1 and f2) (f1: broadside radiation pattern, f2: conical radiation pattern). The proposed structure consists of a central circular antenna and two annular ring antennas; each of the three antennas has individual ports. Two of the ports exhibit orthogonal broadside radiation patterns; the other two ports exhibit orthogonal conical radiation patterns. Thus, they have polarization diversity characteristics. To improve isolation between ports, the inner part of the annular ring antennas is shorted via array, and the outermost port is positioned orthogonal to the other ports. Using this configuration, the isolation between ports was measured as -26.7 dB and -30.1 dB at the two frequency bands, respectively. Experimental results based on the fabricated prototype show that the proposed antenna achieves -10 dB bandwidths of 240 MHz (5.71~5.95 GHz) and 210 MHz (7.69~7.9 GHz) at f1 and f2, respectively.

Since the implementation of the Materials Genome Project by the Obama administration in the United States, the development of various computational materials databases has fundamentally expanded the choices of industries such as materials and energy. In the field of thermoelectric materials, the thermoelectric figure of merit ZT quantifies the performance of the material. From the viewpoint of calculations for vast materials, the ZT values are not easily obtained due to their computational complexity. Here, we show how to build a database of thermoelectric materials based on first-principles calculations for the electronic and heat transport of materials. Firstly, the initial structures are classified according to the values of bandgap and other basic properties using the clustering algorithm K-means in machine learning, and high-throughput first principles calculations are carried out for narrow-bandgap semiconductors which exhibiting potential thermoelectric application. The present framework of calculations mainly includes deformation potential module, electrical transport performance module, mechanical and thermodynamic properties module. We have also set up a search webpage for the calculated database of thermoelectric materials, providing searching and viewing the related physical properties of materials. Our work may inspire the construction of more computational databases of first-principle thermoelectric materials and accelerate research progress in the field of thermoelectrics.

Under the influence of various factors, the bronze ware unearthed by archaeology has various diseases of different degrees, and the mineralization problem is more prominent. The physical properties of mineralized bronzes have been destroyed, and the whole is loose and fragile, which is in urgent need of reinforcement and protection. Common reinforcement and protection materials mainly consider surface sealing, matrix bonding reinforcement and penetration reinforcement. Considering the low matrix strength and complex disease types of fragile bronzeware, it is difficult to achieve targeted protection with commonly used reinforcement and protection materials. In view of the problems such as poor permeability and easy discoloration of commonly used protection materials, this paper uses self-developed reinforcement and protection material AMC to compare its reinforcement and protection performance with B72, which has a high comprehensive evaluation on the performance of commonly used reinforcement and protection materials. The matrix strength was increased, and the appearance intervention degree was less than B72.

In this paper, a dual-band WiFi antenna and its Multiple Input Multiple Output (MIMO) system application is designed, fabricated, and measured based on the Chinese characters “Men” and “Wei”. The antenna uses a 40×40×1.6 mm3 Fr4 substrate to analyze the combinatorial structure of Chinese characters using the theory of characteristic modes (TCM), to optimize the antenna dimensions by analyzing the mode current distribution, and to broaden the antenna bandwidth by etching rectangular slots on the ground. The measured and simulated results show that the four-element MIMO antenna covers 5.68-8.01 GHz, the isolation between the antennas is higher than 20 dB in the working band, the Envelope Correlation Coefficient (ECC) and the channel capacity losses (CCLs)of the simulation is lower than 0.001 and 0.18 bits/s/HZ, respectively. The efficiency of the antenna is higher than 90%, and it can be used for WiFi communication band (5.8 GHz and 6 GHz).

In the process of deflagration of energetic materials, strong electromagnetic radiation is to be generated, which causes the surrounding electronic equipment to fail to work normally. To solve this problem, it is necessary to clarify the mechanism of electromagnetic radiation generated by energetic materials. The mechanism of plasma changed by the deflagration of energetic materials is an important topic in the aerospace and geophysics fields. The academic community holds two main viewpoints on the mechanism of electromagnetic radiation generated by energetic materials: one is that the solid material is squeezed and deformed during the deflagration of energetic materials, and the charges of different polarities rub in space to form effective electric dipoles, which eventually generate electromagnetic radiation. Another view is that the deflagration of energetic materials causes the temperature of the medium to rise sharply, and bremsstrahlung is formed during the compression and diffusion of the high-temperature wave front, resulting in the generation of electromagnetic radiation. This paper, based on theoretical analysis and experimental data, holds the view that electromagnetic radiation is generated by the high-temperature thermal effect. It studies the relationship between temperature and electromagnetic radiation and obtains quantitative analysis conclusions.

A supernova close enough to the Earth is a spectacular event: it can appear as a \new star" as luminous as Venus, or even more, visible for several days. The rate of Galactic supernovae is expected to be of about one in 30 years, with a fraction visible at naked eye; however in all the history of human civilization only seven supernovae in the Milky Way have been reported, the last two (1572 and 1604) during Galilei's life. The supernova of 1604, today called Kepler's Supernova, was observed by Galilei, Kepler and other astronomers in Europe, Korea, and China. Like the supernova SN1572, today called Tycho's supernova, it has been the subject of extensive studies, and inspired observational measurements and philosophical considerations on the nature of the heavens. The remnant of SN1604 has been indicated by recent X- and gamma-ray data to be a likely site of cosmic ray acceleration. The first recorded data of optical observations, together with new data, can still tell us a lot about the early evolution of this supernova.

Major progress in the field of regenerative medicine are expected from the design of artificial scaffolds that mimic both the structural and functional properties of the ECM. The bionanocomposites approach is particularly well fitted to meet this challenge as it can combine ECM-based matrices and colloidal carriers of biological cues that regulate cell behavior. Here we have prepared bionanocomposites under high magnetic field from Tilapia fish scale collagen and multifunctional silica nanoparticles (SiNPs). We show that scaffolding cues (collagen), multiple display of signaling peptides (SiNPs) and control over the global structuration (magnetic field) can be combined into a unique bionanocomposite for the engineering of biomaterials with improved cell performances.

Patch antennas are compact, less complex, planar structures and therefore, widely used in small satellite missions for telecommand, data link, and intersatellite link, particularly in S- band and X- band. Improved performance of these patch antennas in terms of gain and compactness will di-rectly affect the communication efficiency of small satellite missions. Especially the coming IoT (Internet of Things) constellations require high gain and efficient antenna arrays. An optimization of single patch antenna elements is an important cornerstone for the missions. Therefore, the ef-fects of various antenna enhancement techniques, such as slotted ground plane, resistor and ca-pacitor integration, parasitic patch elements, are analyzed. These techniques were applied on a rectangular patch antenna with parameter variation to identify the optimal performances with respect to bandwidth, operating frequency, gain, polarization, and power flow. Finally, the techniques were combined to obtain an optimized antenna in terms of gain and compactness. The results were compared to a slotted reference antenna. For the scenario of a 2.4 GHz patch antenna, a gain optimization of 27 % (from 7.09 to 8.14 dBi) or size reduction of 52 % (from 96.04 to 46.2 cm²) could be achieved. Overall, our study revealed an effective way to increase the patch antenna performance, which can directly contribute to more efficient communication links and design of antenna arrays.

We report world record high data transmission over standard optical fiber from a single optical source. We achieve a line rate of 44.2 Terabits per second (Tb/s) employing only the C-band at 1550nm, resulting in a spectral efficiency of 10.4 bits/s/Hz. We use a new and powerful class of micro-comb called soliton crystals that exhibit robust operation and stable generation as well as a high intrinsic efficiency that, together with an extremely low spacing of 48.9 GHz enables a very high coherent data modulation format of 64 QAM. We achieve error free transmission across 75 km of standard optical fiber in the lab and over a field trial with a metropolitan optical fiber network. This work demonstrates the ability of optical micro-combs to exceed other approaches in performance for the most demanding practical optical communications applications.

Microcombs provide a potential compact and efficient light source for multi-Terabit-per-second optical superchannels. However, as the bandwidth of these multi-wavelength light sources is increased, this can result in low per-line power. Optical amplifiers can be used to overcome power limitations, but the accompanying spontaneous optical noise can degrade performance in optical systems. To overcome this issue, we propose wideband noise reduction for comb lines using a high-Q microring resonator, whose resonances align with comb lines. When applying the proposed distillation to a superchannel system with 18 Gbaud, 64-QAM sub-channels in a > 10 Tb/s optical superchannel, we find that noise-corrupted comb lines can reduce the optical signal-to-noise ratio required for the comb by ~ 9 dB when used as optical carriers at the transmitter side, and by ~ 12 dB when used as a local oscillator at the receiver side.

The rapidly increasing adoption of high-resolution accurate-mass methods in analytical laboratories has fueled demand for instruments that combine high performance and reliability with small size and greater ease-of-use. This paper presents the major design principles that are driving the evolution of the hybrid quadrupole-Orbitrap instrument architecture to enable a greater range of applications and users. These principles may be summarized as follows: better usage of physical space and better access for service by means of size reduction of pumping and ion optics; expanded use of technologies from electronics in ion-optical design; flexibility in performance via modularity of design of the hardware and software components; and, harmonization of interfaces with other instruments to facilitate sharing and transferability of analytical workflows. The design of a novel family of hybrid mass spectrometers is described in detail, and performance evaluation is carried out on a wide variety of samples for its three representatives: the Orbitrap Exploris 120, Orbitrap Exploris 240 and Orbitrap Exploris 480 mass spectrometers.The new instrument family is shown to offer compelling potential not only for high-end proteomics and biopharmaceutical applications, but also for screening, trace, targeted and clinical analysis by liquid chromatography/mass spectrometry methods.

With the continual global increase of PV power systems and the inherent weather-induced volatility of their power output, understanding the underlying variability of solar radiation in both space and time is important for the planning and reliable operation of future power grids. This paper concisely reviews recent advances in the characterization of irradiance variability with an emphasis on small spatial and temporal scales (respectively less than about 10\,km and 1\,min), for which comprehensive data sets are time consuming and expensive to collect, and although needed have not been available until recently. Special attention is given to studies dealing with the quantification of variability using such unique data, the analysis and modeling of spatial smoothing, and the evaluation of temporal averaging.

In this study, we investigate the influence of control type and strain rate on the lifetime of specimens manufactured from 50CrMo4. This influence is described by a strain rate dependent method that uses cyclic stress strain curves to correct displacement controlled cyclic test results. The objective of this correction is to eliminate the stress related differences between displacement controlled cyclic test results and force controlled cyclic test results. The method is applied to the results of ultrasonic fatigue tests of six different combinations of heat treatment, specimen geometry (notch factor) and atmosphere. The corrected results show an improved agreement with test results obtained on conventional fatigue testing equipment with similar specimens: the standard deviation in combined data sets is significantly reduced (p=4.1%). We discuss the literature on intrinsic and extrinsic strain rate effects in carbon steels.

Abiotic stress in plants is an increasingly common problem in agriculture, and thus, studies on plant treatments with specific certain compounds that may help to mitigate these effects have increased in recent years Melatonin (MET) application and its role in mitigating the negative effects of abiotic stress in plants have become important in the last few years. MET, a derivative of tryptophan, is an important plant-related response molecule involved in the growth, development, and reproduction of plants, and the induction of different stress factors. In addition, MET plays a protective role against different abiotic stresses such as salinity, high/low temperature, high light, waterlogging, nutrient deficiency and stress combination by regulating both the enzymatic and non-enzymatic antioxidant defense systems. Also, MET interacts with many signaling molecules, among these, reactive oxygen species (ROS) and nitric oxide (NO), and participates in a wide variety of physiological reactions. It is well known that NO produces S-nitrosylation and NO2-Tyr of important antioxidant-related proteins, being this an important mechanism for maintaining the antioxidant capacity of the AsA/GSH cycle under nitro-oxidative conditions, being extensively reviewed here under different abiotic stress conditions. Lastly, in this review, we show the coordination between NO and MET as a long-range signaling molecule, regulating many responses in plants, including plant growth and abiotic stress tolerance. Despite all the knowledge acquired over the years, there is still more to know about how MET and NO act on tolerance to abiotic stresses.

The key to simulating soil erosion is to calculate the vegetation cover (C) factor. Methods that apply remote sensing to calculate C factor at regional scale cannot directly use the C factor formula. That is because the C factor formula is obtained by experiment, and needs the coverage ratio data of croplands, woodlands and grasslands at standard plot scale. In this paper, we present a C factor conversion method from a standard plot to a km-sized grid based on large sample theory and multi-scale remote sensing. Results show that: 1) Compared with the existing C factor formula, our method is based on the coverage ratio of croplands, woodlands and grasslands on a km-sized grid, takes the C factor formula obtained from the standard plot experiment and applies it to regional scale. This method improves the applicability of the C factor formula, and can satisfy the need to simulate soil erosion in large areas. 2) The vegetation coverage obtained by remote sensing interpretation is significantly consistent (paired samples t-test, t = −0.03, df = 0.12, 2-tail significance p < 0.05) and significantly correlated with the measured vegetation coverage. 3) The C factor of the study area is smaller in the middle, southern and northern regions, and larger in the eastern and western regions. The main reason for that is the distribution of woodlands, the Hunshandake and Horqin sandy lands and the valleys affected by human activities. 4) The method presented in this paper is more meticulous than the C factor method based on the vegetation index, improves the applicability of the C factor formula, and can be used to simulate soil erosion on large scale and provide strong support for regional soil and water conservation planning.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

Product introductions play a pivotal role in the success and competitiveness of manufacturing, particularly in the context of new product development. Low-volume manufacturing companies exhibit distinct characteristics that significantly influence the product introduction process. Notably, the quality of information exchange between product design and production interfaces becomes paramount in this high-mix and low-volume industry. Consequently, there exists a pressing need to explore various methods for adapting and customizing management mechanisms and strategies to align with the unique requirements and characteristics of low-volume manufacturing and its associated product introduction processes. While the need for this knowledge is critical in the context of low-volume manufacturing, a majority of existing studies predominantly focus on the management aspects within high-volume manufacturing. Therefore, the primary aim of this study is to investigate the customization of product introduction management strategies to enhance the quality of information content within the realm of low-volume manufacturing. Drawing upon a longitudinal analysis of new product introductions within a low-volume manufacturing company, this study narratively elucidates how the examined company implemented product introduction management strategies to facilitate the enhancement of information content quality during the product introduction phase. The study presents its findings on management strategies across three key stages: pre-implementation, post-implementation, and subsequent modification and refinement of strategies following the initial round of implementation. By shedding light on these strategies, this study offers a comprehensive understanding of management approaches in the context of low-volume product introduction. As a result, it makes a valuable contribution to the discourse on information management and interface management in the high-mix, low-volume manufacturing literature.

(1) Background: The purpose of this study was to assess the external load demands in futsal, con-sidering both home and away matches and their outcomes, in order to plan microcycles throughout the season based on the external load of each match. (2) Methods: The external load of 10 players from a First Division team in the Spanish Futsal League was recorded. The total dura-tion of player involvement with the clock stopped was 18.15 ±7.04 minutes. The players' external load was monitored using OLIVER devices. To analyse the influence of the match outcome and location on the external load, a univariate general linear model (GLM) analysis was conducted. (3) Results: There are no differences between the variables, except for accelerations of 2 to 3 m/s² (m) per minute and the number of accelerations of 2 to 3 m/s² per minute. Despite not showing significant differences, there is a trend indicating a higher demand for external loads in away matches as well as in matches won. (4) Conclusions: These findings are important for planning microcycles and providing the appropriate dosage to each player to achieve optimal performance in matches.

(1) Background:The objective of this study was to explorethe dynamic changes of gut microbiota in Simmental calves before weaning, and compared microbial composition and functionality differences between diarrhea and health calves; (2) Methods: Fourteen neonatal Simmental calves were divided into a health group (n = 8) and diarrhea group (n = 6). The rectal stool samples were collected from each calf on days 1, 3, 5, 7, 9, 12, 15, 18, 22, 26, 30, 35, and 40. The high-throughput sequencing analysis of the 16S rRNA gene V1–V9 region was conducted to explore the changes in gut microbiota over time in both groups and assess the influence of diarrhea on microbiota structure and function; (3) Results: E.coli, B.fragilis, and B.vulgatus were the top three bacterial species of pre-weaning Simmental calves.Meanwhile, the major functions of fecalmicrobiota included the “Metabolic pathways”,“Biosynthesis of secondary metabolites”,“Biosynthesis of antibiotics”, “Microbial metabolism in diverse environments”, and “Biosynthesis of amino acids”. For calves in health group, PCoA revealed that the bacterial profiles generated from days 1, 3, 5, 7, and 9 separated from days 15, 18, 22, 26, 30, 35, and 40. While the microbial profiles of calves on day 12 crossed with both clusters, suggesting that the dynamic changes of microbial structures with the increasing of ages. When compared the difference of the relative abundance of bacteria between calves in health and diarrhea groups, the results showed that the relative abundance of the beneficial L.johnsonii, F.prausnitzii, and Limosilactobacillus in the health group were significantly higher than those in the diarrhea group (p

There are four types of influenza viruses: A, B, C, and D. Cattle are susceptible to influenza D infection and serve as a reservoir for this seven-segmented influenza virus. It is generally thought that bovines are not a host of other types of influenza viruses including type A. This long-standing viewpoint has been challenged by the recent highly pathogenic avian influenza (HPAI) H5N1 outbreaks in dairy cows in the United States. To date, HPAI H5N1 has spread into nine states affecting 49 dairy herds and causing clinical symptoms including reduced appetite, fever, and a sudden drop in milk production. This review article describes the current epidemiological landscape of HPAI H5N1 in U.S. dairy cows and the recent interspecies transmission events of HPAI H5N1 in other mammals reported in other countries. The review also discusses adaptation mutations of HPAI H5N1 to mammalian hosts and vaccination strategies. Finally, it summarizes some immediate questions that need to be addressed towards a better understanding of infection biology, transmission, and immune response of HPAI H5N1 in bovines.

Two novel members of the subfamily Betarhabdovirinae, family Rhabdoviridae, were identified in Brazil. Overall, their genomes have the typical organization 3’-N-P-P3-M-G-L-5’ observed in mono-segmented plant-infecting rhabdoviruses. In aristolochia-associated cytorhabdovirus (AaCV), found in the liana aristolochia (Aristolochia gibertii Hook), an additional short orphan ORF encoding a transmembrane helix was detected between P3 and M. AaCV genome and deduced encoded proteins share the highest identity values, consistently < 60%, with their counterparts of yerba mate chlorosis-associated virus (Cytorhabdovirus flaviyerbamate). The second virus, false jalap virus (FaJV), was detected in the herbaceous plant false jalap (Mirabilis jalapa L.) and represents together with tomato betanucleorhabdovirus 2, originally found in tomato plants in Slovenia, a tentative new species of the genus Betanucleorhabdovirus. FaJV particles accumulate in the peri-nuclear space, and electron-lucent viroplasms were observed in the nuclei of the infected cells. Notably, distinct from typical rhabdoviruses, most virions of AaCV were observed to be non-enclosed within membrane-bounded cavities. Instead, they were frequently seen in close association with surfaces of mitochondria or peroxisomes. Unlike FaJV, AaCV was successfully graft-transmitted to healthy plants of three species of the genus Aristolochia, while mechanical and seed transmission proved unsuccessful for both viruses. Data suggest that these viruses belong to two new tentative species within the subfamily Betarhabdovirinae.

In this study, alfalfa silage with different packing densities (500 kg/m3, 600 kg/m3 and 700 kg/m3) were set up under outdoor high temperature and indoor normal temperature. The chemical composition, fermentation quality and microbial community of alfalfa silage were analyzed. The results showed that DM and WAC content decreased with the increase of density. When the density is 600kg/m3, CP content reaches the maximum and ADF content is the lowest. Temperature has a certain effect on alfalfa silage. The content of Lactobacillus plantarum fermented at high temperature is lower than that fermented at normal temperature. At the same time, the content of Lactobacillus plantarum decreased with the increase of packing density. However, the content of Lactobacillus plantarum was the lowest when the packing density was 600 kg/m3 at high temperature. In summary, this study explained the effects of different temperature and density on alfalfa fermentation quality and microbial community, and clarified that the density should be reasonably controlled within 600 kg/m3 during alfalfa silage, providing theoretical support for production practice.

With nearly 1,700 species, Microsporidia represent a group of obligate intracellular eukaryotes with veterinary, economic and medical impacts. To help in understanding the biological functions of these microorganisms, complete genome sequencing is used routinely. Nevertheless, the proper prediction of their gene catalogue is challenging due to taxon-specific evolutionary features. As innovative genome annotation strategies are needed to obtain a representative snapshot of the overall lifestyle of these parasites, the MicroAnnot tool, a dedicated workflow for microsporidian sequence annotation using data from curated databases of accurately annotated microsporidian genes, has been developed. Furthermore, specific modules have been implemented to perform small genes (&lt; 300bp) and transposable element identification. Finally, functional annotation was performed using the signature-based InterProScan software. MicroAnnot’s accuracy has been verified by the re-annotation of four microsporidian genomes for which structural annotation had previously been validated. With its comparative approach and transcriptional signal identification method, MicroAnnot provides accurate prediction of translation initiation sites, efficient identification of transposable elements, as well as high specificity and sensitivity for microsporidian genes including those under 300 bp. Thanks to its web interface (https://microannot.org), MicroAnnot is available to the community to ensure high quality annotation of microsporidian genomes.

The high protein content of several microalgal species makes them attractive and unconventional for applications in the food and pharmaceutical industries. Due to microalgae's robust cell wall, cell rupture is necessary to improve the extraction of their intracellular proteins. Thus, choosing a suitable cell-breaking treatment before protein extraction is a vital downstream processing step. Additionally, it is necessary to use an effective technique for monitoring and measuring the impact of rupture treatments on microalgal cell walls. In our study, Tetradesmus obliquus cells were disrupted by three different mechanical rupture methods: high-pressure homogenization (HPH), ultrasound (US), and ball milling (BM). The ruptured biomass cells were counted, and soluble proteins were extracted and quantified. The cell counting technique did not detect differences between intact and damaged cells after BM treatment because the dye (erythrosine B) did not permeate the microalgae biomass accurately. The US treatment promoted the highest yield of total protein extraction (19.95%). The yields of protein extraction of T. obliquus with HPH (15.68%) and BM (14.11%) were significantly (p value ≤ 0.05) lower than that achieved in the US treatment. The increase in the number of extraction steps increased the protein recovery. Thus, the content of extracted soluble protein was a reliable indirect index for a quantitative comparison of the cell disruption level.

Accretionary and collisional orogeny are often accompanied by the disturbance of the geothermal gradient, leading to high-temperature metamorphism. High-temperature metamorphic rocks are significant in their ability to help the reconstruction of the thermal histories of orogenic belts. The Tianshan Orogenic Belt, at the southwest margin of the Central Asian Orogenic Belt, is a record of the long-term subduction–collision–post-collision orogenic process that has taken place in the Phanerozoic Eon. Here, we report the discovery of mafic granulites in the Muzhaerte area, SW Tianshan. Petrographic observation reveals that the mafic granulites underwent two metamorphic stages. The peak mineral assemblages of the first stage are dominated by clinopyroxene + orthopyroxene + plagioclase + quartz + hornblende ± biotite, and the post-peak mineral assemblages of the second stage are dominated by clinopyroxene + plagioclase + quartz + amphibole + biotite. The calculated results obtained from the two-pyroxene thermobarometers and the Al-in-hornblende barometer for the mafic granulites indicate that the metamorphic conditions of mafic granulites are 760–860 ℃ and < 0.39–0.41 Gpa. The mafic granulites recorded a high-grade granulite facies thermal metamorphic event with the highest temperature limit currently recorded in the Central Tianshan Block.

Hessenberg differential algebraic equations (Hessenberg-DAEs) with high index play a critical role in the modeling of mechanical systems and multibody dynamics. Motivated by the widely used Lie Group Differential Algebraic Equation (LGDAE) method which only handles index 2 systems, we propose a Modified Extended Lie Group Differential Algebraic Equation (MELGDAE) method for solving index 3 Hessenberg-DAEs, and provide theoretical analysis to deepen the foundation of the MELGDAE method.The performance of the MELGDAE method is compared with the standard methods RADAU and MEBDF on index 2 and 3 DAE systems, and it is demonstrated that the MELGDAE integrator exhibits competitive performance in terms of high accuracy and the preservation of algebraic constraints. In particular, all differential variables in index 3 Hessenberg DAEs achieve second-order convergence using the MELGDAE method, which suggests potential for extension to Hessenberg-DAEs with an index of 4 or higher.

The temperature-assisted laser shock process has shown promising prospects in the fields of forming manufacturing and surface strengthening. However, large-scale application of this process is limited by the instability and failure of confinement medium at high temperatures (≥300 ℃). Aiming at this problem, we propose a novel laser shock strategy based on Leidenfrost effect, where the suspended droplets are utilized as the confinement medium. According to the sequence of images acquired by time delay system and high-speed camera, the droplet dynamics behavior is studied. The focusing enhancement effect of the droplet is comprehensively explored. And the correlations between droplet size, ambient temperature, vapor layer thickness and focusing effect are investigated. Combining the dynamics and focusing enhancement effect of droplets, a theoretical model of laser shock pressure under droplet confinement is established. Finally, the effectiveness and feasibility of the droplet-based laser shock strategy in high temperature processing environments are verified by typical applications in laser shock forming and laser shock peening fields. The results show that the droplet-based laser shock process presents better forming effect. And the mechanical property tests demonstrate that this process can obtain the simultaneous improvement of the strength (~51%) and ductility (~6.4%) of annealed Cu. The multiscale plasticity mechanisms of the strengthened material are comprehensively investigated. We believe that this low-energy, low-cost and high-quality process can provide a new solution for the industrial application of laser shock at high temperatures.

To realize precise control of the quantum dots (Qdots) device, multi-channel precision bias source plays the key role. In this paper, the 16-channel high precision bias source with 18-bit resolution for Qdots device was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The step response time is less than 3μs. The resolution, stability, linearity and dynamic range of the bias source exhibits good performance. What's more, the bias source can be controlled locally and online. The results show that it is one effective and feasible topology for experiments in Qdots device application.

Significant problems have arisen in the last years, such as climate change, global warming, and hunger. These complications are correlated with the depletion and exploitation of natural resources and environmental contamination. Due to overcrowding, the list of challenges for the next few years is growing. A comprehensive approach was made to the agro-industrial production of Avocado (Persea americana) and the management of all its biomass waste. So, bioprocesses and biorefinery can be used to produce high added-value products. A large number of residues are composed of lignin and cellulose. They have many potentials to be exploited sustainably for chemical and biological conversion; physical, chemical, and natural treatments improve the following operations. There are some applications to many fields such as pharmaceutical, medical, material engineering, and environmental remediation. Possible pathways are mentioned to take advantage of Avocado as biofuels, drugs, bioplastics, and even in the environmental part and emerging technologies such as nanotechnology using bioprocesses and biotech. In conclusion, Avocado and its waste could be transformed into high value-added products in industries above to mitigate global warming and save non-renewable energy.

Melanophryniscus admirabilis (admirable red-belly toad) is a microendemic and critically endangered species found exclusively along 700 meters of the Forqueta River, in a fragment of Atlantic Forest in southern Brazil. One of the greatest concerns regarding the conservation of this species is the extensive use of pesticides in areas near their natural habitat. In recent years, the adaptation and persistence of animal species in impacted environments have been associated with microbiota. Therefore, the current study aimed to characterize the oral bacterial community of wild M. admirabilis and to address the question of how this community might contribute to toad’s adaptation in the anthropogenic environment and its general metabolic capabilities. In the present study, 11 oral samples collected from wild M. admirabilis were characterized and analyzed via high-throughput sequencing. A total of 181,350 sequences were obtained, resulting in 16 phyla, 34 classes, 39 orders, and 77 families. Proteobacteria dominated (53%) the oral microbiota of toads followed by Firmicutes (18%), Bacteroidetes (17%), and Actinobacteria (5%). No significant differences in microbial community profile from among the samples were reported, suggesting that the dietary restriction may directly influence the bacterial composition. Functional inference of microbiome was performed using PICRUSt2 and important pathways, such as xenobiotic degradation pathways to pesticides and aromatic phenolic compounds were detected, suggesting that the bacterial communities may have important roles in M. admirabilis health and survival in the anthropogenic environment. Overall, our results have important implications for the conservation and management of this microendemic and critically endangered species.

The expansion of concrete subjected to extreme elevated temperature is linked with intricate micro-structural variations, such as the transformation of the constituent phases. This study proposes a model to predict the thermal expansion of cement paste and concrete considering micro-structural changes under elevated temperatures ranging from 20°C to 800°C. The model presented can consider characteristics of various aggregates in the calculation of thermal expansion for concrete. The model is a combination of a multi-scale stoichiometric model and a multi-scale composite model. At the cement paste level, the model satisfactorily predicted a test result. At concrete level, upper bounds from the model were matched relatively well with test results by previous researcher. If the mechanical properties, such as elastic modulus (E), Poisson’s ratio (ν), and thermal deformation, of the aggregates used in concrete are given, it is likely that the model will reasonably predict experimental results.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

A general procedure is described, to generate material parameter sets to simulate fire propagation in horizontal cable tray installations. Cone Calorimeter test data is processed in an inverse modelling approach. Here, parameter sets are generated procedurally and serve as input for simulations conducted with the Fire Dynamics Simulator (FDS). The simulation responses are compared with the experimental data and ranked based on their fitness. The best fitness was found for a test condition of \SI{50}{\kilo\watt\per\meter^2}. Low flux conditions \SI{25}{\kilo\watt\per\meter^2} and less exhibited difficulties to be simulated accurately. As a validation step, the best parameter sets are then utilised to simulate fire propagation within a horizontal cable tray installation and are compared with experimental data. It is important to note, the inverse modelling process is focused on the Cone Calorimeter and not aware of the actual validation step. Despite this handicap, the general features in the fire development can be reproduced, however not exact. The fire in the tray simulation extinguishes earlier and the total energy release is slightly higher as compared to the experiment. The responses of the material parameter sets are briefly compared with a selection of state of the art procedures.

The morphology of virgin reactor powder (RP) of high-density polyethylene HDPE with MW = 160,000 g/mol was investigated with the help of DSC, SEM, SAXS and WAXS methods. The morphological SEM analysis showed, that the main morphological units of RP are macro- and micro-shish kebab structures with significantly different geometric dimensions, as well as individual lamellae of folded chain crystals. Quantitative analysis of an asymmetric SAXS reflection made it possible to reveal the presence of several periodic morphoses in the RP with long periods from 20 nm to 60 nm and to correlate them with the observed powder morphology. According to the DSC crystallinity data, the thickness of the lamellae in each long period was estimated. Their surface energy was calculated in the framework of the Gibbs-Thompson theory. The presence of regular and irregular folds on the surface of the different shish-kebab lamellae is discussed. The percentage of identified morphoses in the RP was calculated. It has been suggested that the specific structure of HDPE RP is due to the peculiarity of polymer crystallization during suspension synthesis in a quasi-stationary regime, in which local overheating and inhomogeneous distribution of shear stresses in a chemical reactor are possible.

Constructing a globally consistent high-precision map is essential for the application of mobile robots. Existing optimization-based mapping methods typically constrain robot states in pose space during the graph optimization process, without directly optimizing the structure of the scene, thereby causing the map to be inconsistent. To address the above issues, this paper presents a three-dimensional (3D) LiDAR mapping framework (i.e., BA-CLM) based on LiDAR bundle adjustment (LBA) cost factors. We propose a multivariate LBA cost factor, which is built from a multi-resolution voxel map, to uniformly constrain the robot poses within a submap. The framework proposed in this paper applies the LBA cost factors for both local and global map optimization. Experimental results on several public 3D LiDAR datasets and a self-collected 32-line LiDAR dataset demonstrated that the proposed method achieves accurate trajectory estimation and consistent mapping.

In a new construction of a seventeen-storey building, it is necessary to remove a prop on the second floor, which has made it possible to complete the structure of the building. In the drafting of the executive project, no security measures were described, because it was understood that they were not necessary. In the construction phase, the need to monitor the process was raised, and to be able to stop it, or reverse it if necessary. It is a reinforced concrete structure, with metal elements and composite elements, with a torsional behavior of the cores making the slabs serve as horizontal diaphragms, so the final behavior could be different from what was expected. To make this process possible, two pairs of four metallic cantilevers were introduced into which four Hydraulic pistons were inserted. Before starting the process, they were loaded to be sure that they would not fail. Strain gauges were also placed to control the stresses and how the situation changed during the unshoring process. The process of cutting the provisional pillar was a success, obtaining less deformations than expected, having a complementary safety.

Aiming at the problem of small size of some spots on apple leaves and the difficulty of accurate detection of spot targets brought by the complex background of the orchard, this paper takes the alternaria leaf spot, rust, brown spot, grey spot and frog eye leaf spot on apple leaves as the research object, and proposes a high-accuracy detection model YOLOv5-Res and lightweight detection model YOLOv5-Res4 are proposed. Firstly, a multiscale feature extraction module ResBlock is designed by combining the Inception multi-branch structure and ResNet residual idea. Secondly, a lightweight feature fusion module C4 is designed to reduce the number of model parameters while improving the detection ability of small targets. Finally, a parameter streamlining strategy based on optimized model architecture is proposed. The experimental results show that the performance of YOLOv5-Res model and YOLOv5-Res4 model is significantly improved, the [email protected] value is improved by 2.8% and 2.2% compared with YOLOv5s model and YOLOv5n model, respectively, and the size of YOLOv5-Res model and YOLOv5-Res4 model is only 10.8MB and 2.4MB, and the number of model parameters is reduced compared with YOLOv5s model and YOLOv5n model. counts are reduced by 22% and 38.3% compared to the YOLOv5s model and YOLOv5n model.

Benveniste’s experiments – known in the lay press as the “water memory” phenomenon – are generally considered to be a closed case. However, the amount of data generated by twenty years of well-conducted experiments prevents closing the file so simply. An issue, which has been little highlighted so far, merits to be emphasized. Indeed, if Benveniste failed to persuade his peers of the value of his experiments, it was mainly because of a stumbling block, namely the difficulty of convincingly proving the causal relationship between the supposed cause (“informed water”) and the experimental outcomes in different biological models. To progress in the understanding of this phenomenon, we abandon the idea of any role of water in these experiments (“water memory” and its avatars). In other words, we assume that “control” and “test” conditions to be evaluated were physically identical and differed only by their respective designations. We show in this article how simple probabilistic considerations allow to build a model that accounts for all aspects of Benveniste’s experiments. In this model based on probability amplitudes, constructive and destructive interferences emerge – or not – according to the experimental context. The recording of a statistical regularity shapes the intertwined whole constituted by the probability amplitudes of the states of the experimenter’s cognitive structures and of the experimental system. This model provides an alternative explanation to Benveniste’s experiments where water plays no role and where the place of the experimenter is central.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

This study aimed to identify miRNA editing sites during adipose tissue development in Ningxiang pigs and analyze their characteristics and functions. Based on the small RNA-seq data from subcutaneous adipose tissue samples of Ningxiang pigs at four stages (30, 90, 150 and 210 days), we constructed a developmental atlas of the miRNA editome in adipose tissue of Ningxiang pigs. The characteristics and functions of this editome were further explored through bioinformatics analysis. The findings revealed that a total of 505 miRNA editing sites were identified with C-to-U editing types being the most prevalent, followed by U-to-C, A-to-G and G-to-U. Importantly, these four types of miRNA editing exhibited a base preference. The number of editing sites showed obvious differences among age groups, with the highest occurrence of miRNA editing events observed at 90 days of age and the lowest at 150 days of age. In the miRNA seed region, a total of 9 miRNA editing sites were identified with significant differences in editing levels (P &lt; 0.05), and located in ssc-miR-23a, ssc-miR-27a, ssc-miR-30b-5p, ssc-miR-15a, ssc-miR-497, ssc-miR-15b, and ssc-miR-425-5p, respectively. Target gene prediction and enrichment analysis revealed that the editing of miR-497 may potentially regulate fat deposition by inhibiting adipose synthesis via influencing target binding. These results provide new insights into the regulatory mechanism of pig fat deposition.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

During the last few years, advancement in the area of biochemistry, science of the material world, engineering and computer-aided testing has directed towards advancement of high-throughput tools for the sake of profiling information encoded in a gene. Single-cell RNA-sequencing (scRNA-seq) tools capable to examine the sequence data from each individual cells and it shows within population variety and permit exploring of cell conditions and transformation by extreme resolution, possibly give out cell sub-types or gene expression fluctuations that are shaded in mass sequencing processes, which shows population-averaged evaluations. Yet, the major disadvantage for this tool is the lack of success to pick out location related details of the RNA transcriptome, as this needs tissue detachment and cell isolation. Location based transcript determination is among the advancements in the area of medical biotechnology as this can find out the molecules like RNA dataset in their intact physical placement in tissue segment with spatial context at the scale of a single-cell, which is very advantageous as compare to single-cell sequencing techniques. These approaches give key observation in the areas of biomedical field sub-disciplines like neurology, embryology, carcinoma study, immune cell investigation and histological activities. Generally, this review mainly focused towards single-cell sequencing methods, technology development, its challenges observed, different expression data analysis mechanisms and their applications in different areas, such as in cancer research, microbes, central nervous system, sex organs and immune-biology, intensifying the essentiality of sequencing tools at single-cell level for the characterization of extremely dynamic individual cells.

Leaf area estimation is a critical component in the study of plant growth and productivity within agricultural systems. This research introduces the LeafArea package, a specialized tool designed to calculate the leaf area of six distinct Andean fruit species: S. quitoense, S. betaceum, P. peruviana, R. fruticosus, P. ligularis and P. edulis. Leveraging response variables such as species type, leaf length and width, the package employs advanced machine learning algorithms to estimate leaf area accurately. The primary focus of the study is to identify the most effective model for describing the relationship between leaf width, length, and area for each plant species. Currently, the LeafArea package utilizes four different machine learning algorithms, namely generalized linear model (GLM), generalized linear mixed model (GLMM), Random Forest and XGBoost. Among these, XGBoost stands out as a top-performing algorithm, exhibiting exceptional predictive accuracy. The evaluation metrics employed in the program provide valuable insights for researchers, aiding in informed decision-making. Specifically, XGBoost demonstrates significantly lower prediction errors and approaches a near-perfect R2 value, emphasizing its potential to enhance predictive accuracy. These results underscore the efficacy of machine learning techniques, as a compelling choice for researchers seeking precise and robust predictions in leaf area estimation. The LeafArea package thus represents a valuable tool for advancing our understanding of plant growth dynamics, resource allocation, and overall productivity within agricultural ecosystems.

The flow stress of face-centered cubic (FCC) metals exhibits a rapid increase near a strain rate of 104 s-1 under fixed strain conditions. However, many existing constitutive models either fail to capture the mechanical characteristics of this plastic deformation or use piecewise strain rate hardening models to describe this phenomenon. Unfortunately, the piecewise models may suffer from issues such as discontinuity of physical quantities and difficulties in determining segment markers, and struggling to reflect the underlying physical mechanisms that give rise to this mutation phenomenon. In light of this, this paper proposes that the abrupt change in flow stress sensitivity to strain rate in FCC metals can be attributed to microstructural evolution characteristics. To address this, a continuous semi-empirical physical constitutive model for FCC metals is established based on the microstructural size evolution proposed by Molinari-Ravichandran and the dislocation motion slip mechanism. This model effectively describes the mutation behavior of strain rate sensitivity under fixed strain, particularly evident in the annealed OFHC. The predicted results of the model across a wide range of strain rates (10-4 − 106 s-1) and temperatures (77 − 1096 K) demonstrate relative errors generally within ±10% of the experimental values. Furthermore, the model is compared to five other models, including Mechanical Threshold Stress (MTS), Nemat-Nasser-Li (NNL), Preston-Tonks-Wallace (PTW), Johnson-Cook (JC), and Molinari-Ravichandran (MR) models. A comprehensive illustration of errors reveals that the proposed model outperforms the other five models in describing the plastic deformation behavior of OFHC. The error results offer valuable insights for selecting appropriate models for engineering applications and provide significant contributions to the field.

Resonant light scattering by mesoscale dielectric spheres has received enormous attention and found many interesting applications. The recently emerged field of Mesotronics provides novel opportunities for wavelength-scaled optics and new fundamental aspects are still being uncovered. It has recently been demonstrated that high-order Mie resonances can be excited in homogeneous low-dissipation mesoscale dielectric spheres, leading to the generation of intense magnetic fields. This Letter describes a simple and effective way to drastically enhance the superresonance effect. Proof-of-principle results for the first time show that yet one more novel phenomenon of increasing the intensity of the magnetic field without changing the resonant Mie size parameter of the sphere by introducing an air cavity. In such a dielectric cenosphere (from two Greek words “kenos” - hollow and “sphaira” - sphere), by correct choosing of the air cavity size, it is possible to increase the intensity of the electromagnetic fields at the poles of the sphere by an order of magnitude due to increasing of amplitude of resonant partial wave coefficient.