This article explores the required amount of time series points from a high-speed traffic network to accurately estimate the Hurst exponent. The methodology consists in designing an experiment using estimators that are applied to time series, followed by addressing the minimum amount of points required to obtain accurate estimates of the Hurst exponent in real-time. The methodology addresses the exhaustive analysis of the Hurst exponent considering bias behavior, standard deviation, mean square error, and convergence using fractional Gaussian noise signals with stationary increases. Our results show that the Whittle estimator successfully estimates the Hurst exponent in series with few points. Based on the results obtained, a minimum length for the time series is empirically proposed. Finally, to validate the results, the methodology is applied to real traffic captures in a high-speed network based on the IEEE 802.3ab standard.

FeIFeI Fe2(S2C3H6)(CO)6(µ-CO) (1a-CO) and its FeIFeII cationic species (2a+-CO) are the simplest model of the CO-inhibited [FeFe] hydrogenase active site, which is known to undergo CO photolysis within a temperature- dependent process whose products and mechanism are still a matter of debate. Using Density Functional Theory (DFT) and Time-Dependent Density Functional Theory (TDDFT) computations, the ground state and low-lying excited state potential energy surfaces (PESs) of 1a-CO and 2a+-CO have been explored aimed at elucidating the dynamics of the CO photolysis yielding Fe2(S2C3H6)(CO)6 (1a) and Fe2(S2C3H6)(CO)6+ (2a+), two simple models of the catalytic site of the enzyme. Two main results came out from these investigations. First, a-CO and 2a+-CO are both bound with respect to any CO dissociation with lowest free energy barriers around 10 kcal mol-1, suggesting that at least 2a+-CO might be synthetized. Second, focusing on the cationic form, we found at least two clear excited state channels along the PESs of 2a+-CO that are unbound with respect to equatorial CO dissociation.

Structural and morphological properties of the hydronium-potassium jarosite microstructures were investigated in this work, and their electrical properties were evaluated. All microstructures were synthesized at a reasonable temperature of 343 K with a reduced reaction time of 3 hours. Increase in the pH from 0.8 to 2.1 decreased the particle sized from 3 µm to 200 nm and increasing the aging time from 0, 3 to 7 days resulted in semispherical, spherical and euhedreal jarosite structures, respectively. A Rietveld analysis also was done, finding that increasing pH, the amount of hydronium substitution by potassium in the cationic site also increases, having a 77.72 % of hydronium jarosite (JH) plus 22.29 % potassium jarosite (JK) at pH 0.8; 82.44 % (JH) and 17.56 % (JK) at pH 1.1, and 89.98 % (JH) plus 10.02 % (JK) at pH 2.1. The results obtained in this work show that the obtained hydronium potassium jarosite microstructures with reduced particle size and euhedreal morphology can be used as anode materials for improving the life time of lithium ion batteries, due that during the analysis of the voltage obtained using electrodes made with this particles and graphite, this ranged from 0.89 to 1.36 V.

The aim was to examine the sociodemographic predictors associated with changes in movement behaviours (physical activity, screen time and sleep) among toddlers and pre-schoolers during the early stages of the coronavirus disease 2019 pandemic in Chile. Caregivers of 1- to 5-year-old children completed an online survey between March 30th and April 27th, 2020. Information about the child's movement behaviours before (retrospectively) and during the pandemic, as well as family characteristics were reported. In total, 3,157 participants provided complete data (mean children age: 3.1±1.38 years). During early stages of the pandemic, time spent in physical activity decreased, recreational screen time and sleep duration increased, and sleep quality declined. Toddlers and pre-schoolers with space to play at home and living in rural areas experienced an attenuated impact of the pandemic restrictions on their physical activity levels, screen time, and sleep quality. Older children, those whose caregivers had a higher educational level, and children living in apartments had greater changes, mainly a decrease in total physical activity and increase in screen time. This study has shown the significant impact of the pandemic restrictions on movement behaviours in toddlers and pre-schoolers in Chile.

Previously, various techniques have been proposed for reducing the lift-off effect on the thickness measurement of the non-magnetic films, including the peak-frequency feature and phase feature in the Dodd-Deed analytical formulation. To realise a real-time feedback response on the thickness monitoring, the phase term in the Dodd-Deeds formulation must be taken off the integration. Previous methods were based on the slow change rate of the phase term when compared to the rest of the term – the magnitude term. However, the change rate of the phase term is still considerable for a range of working frequencies. In this paper, a high-frequency feature has been found. That is, the ratio between the imaginary and real part of the phase term is proportional to the integral variable under high frequencies. Based on this proportion relationship, the phase term has been taken out; and a thickness algorithm has been proposed. By combing the measured impedance from the custom-built sensor (three coils), the thickness of the metallic film can be reconstructed. Experiments have been carried out for the verification of the proposed scenario. Results show that the thickness of the metal film can be reconstructed with a small error of less than 2 %, and immune to a reasonable range of lift-offs.

Room-temperature phosphorescent (RTP) materials have been attracted tremendous interest owing to their unique material characteristics and potential applications for state-of-the-art optoelectronic devices. Recently, we have reported a synthesis and fundamental photophysical properties of new RTP materials based on benzil, i.e., fluorinated monobenzil derivative and fluorinated and non-fluorinated bisbenzil derivative analogues [Yamada, S. et al, Beilstein J. Org. Chem. 2020, 16, 1154–1162.]. To further understand their RTP properties, here we investigated the excited-state dynamics and photostability of the derivatives by means of time-resolved and steady-state photoluminescence spectroscopies. For these derivatives, clear RTP emissions with lifetimes on the microsecond timescale were identified. Among them, the monobenzil derivative was found to be the most efficient RTP material, showing both the longest lifetime and highest amplitude RTP emission. Time-resolved photoluminescence spectra measured at 77 K and density functional theory calculations revealed the existence of a second excited triplet state in the vicinity of the first excited singlet state for the monobenzil derivative, indicative of the presence of a fast intersystem crossing pathway. A discussion of the correlation between the excited state dynamics, emission properties, and conformational flexibility of the three derivatives is presented.

In Cameroon, alcoholic beverages remain the main consumed drink. In the Northern regions, indigenous sorghum beers are popular and widely consumed in an actively fermenting state by the people. In this study, some physicochemical parameters of the alcoholic sorghum beverages and correlations between them were evaluated during fermentation for 10 days. The indigenous white and red beers were produced at the laboratory scale assisted by experimented producers and some parameters (pH, total acidity, alcohol, sugars, density, total solids, temperature, and conductivity) were measured on the wort and fermented beverages. The pH decreases from 3.2 to 2.4 and 3.11 to 2.41; total acidity increases from 1.07 to 5.1 g/l and 0.5 to 4.6 g/l; alcohol enhances from 0 to 9.5% and 0 to 6.8% (v/v); total solids drop from 13.6 to 5°P and 12.2 to 3.3°P were observed respectively in the white and red sorghum beers. The multivariate analysis showed a good correlation between consumption of sugar, the decrease of total solids and density with the decrease in pH. It was also shown that, a perfect link exist between the production of alcohol and organic acids. The hierarchical analysis showed that indigenous red beer samples fermented for 1 and 2 days and those fermented for 4 to 10 days are related and could be separate in two distinct groups, whereas white turbid beer samples are separated in three different groups, those fermented for 1 to 4 days, those 5 to 6 days and those 7 to 10 days. The results obtained could serve as a guide to better understand the fermentation process of the indigenous alcoholic sorghum-based beverages.

Time-restricted feeding (TRF) showed a potent effect in preventing obesity and improving metabolic outcomes in several animal model of obesity; however, there is, as yet, scarce evidence about its effectiveness against obesogenic challenge that more accurately mimic the human Western diets, such as cafeteria diet. Moreover, the mechanism for its efficacy is poorly understood. White adipose browning has been linked to body weight loss. Herein, we tested whether TRF has the potential to induce browning of inguinal white adipose tissue (iWAT) and to attenuate obesity and associated dyslipidemia in cafeteria diet-induced obesity model. Male Wistar rats, fed normal laboratory chow (NC) or cafeteria diet (CAF) for 16 weeks, were subdivided into two groups that were subjected to either ad libitum (ad lib, A) or TRF (R) for 8 hours per day. Rats under TRF regimen had a lower body weight gain and adiposity compared with their diet-matched ad lib rats, despite equivalent levels of food intake and locomotor activity. In addition, TRF improved the deranged lipid profile [total cholesterol (TC); triglycerides (TG); high density lipoprotein (HDL-c); low density lipoprotein (LDL-c)] and atherogenic indices [atherogenic index of plasma (AIP); atherogenic coefficient (AC); coronary risk index (CRI)] in rats fed CAF diet. Remarkably, TRF resulted in decreased size of adipocytes and induced emergence of multilocular brown-like adipocytes in iWAT of NC- and CAF-fed rats. Protein expression of browning markers, such as uncoupling protein-1 (UCP1) and peroxisome proliferator activated receptor gamma coactivator 1-alpha (PGC1α) in iWAT were also up-regulated in time restricted NC- or CAF-fed rats. These findings suggest that TRF regimen is an effective strategy to improve obesity and associated dyslipidemia induced by CAF-diet, probably via a mechanism involving WAT browning process.

A lot of previous research have proposed various frameworks and algorithms to optimize routes to reduce the total transportation cost, which accounts for over 70% of overall logistics cost. However, it is very hard to find the cases applied the mathematical models or algorithms to the practical business environment cases, especially daily operating logistics services like convenient stores. Most of previous research have considered the developing an optimal algorithm which can solve the mathematical problem within the practical time while satisfying all constraints such as the capacity of delivery and pick-up, and time windows. For the daily pick-up and delivery service like supporting several convenient stores, it is required to consider the unit transporting container as well as the demand, capacity of trucks, traveling distance and traffic congestion. Especially, the reusable transporting container, trays, should be regarded as the important asset of logistics center. However, if the mathematical model focuses on only satisfying constraints related delivery and not considering the cost of trays, it is often to leave the empty trays on the pick-up points when there is not enough space in the track. In this research, it has been proposed to build the mathematical model for optimizing pick-up and delivery plans by extending the general vehicle routing problem of simultaneous delivery and pickup with time windows while considering left-over cost. With the numerical experiments, it has been proved that the proposed model may reduce the total delivery cost. It may be possible to apply the proposed approach to the various logistics business which uses the reusable transporting container like shipping containers, refrigerating containers, trays, and pallets.

We propose a Gauss model (GM), a map from time to the bell-shaped Gauss function to model the deaths per day and country, as a quick and simple model to make predictions on the coronavirus epidemic. Justified by the sigmoidal nature of a pandemic, i.e. initial exponential spread to eventual saturation, we apply the GM to existing data, as of April 2, 2020, from 25 countries during first corona pandemic wave and study the model's predictions. We find that logarithmic daily fatalities caused by Covid-19 are well described by a quadratic function in time. By fitting the data to second order polynomials from a statistical chi2-fit with 95\% confidence, we are able to obtain the characteristic parameters of the GM, i.e. a width, peak height and time of peak, for each country separately, with which we extrapolate to future times to make predictions. We provide evidence that this supposedly oversimplifying model might still have predictive power and use it to forecast the further course of the fatalities caused by Covid-19 per country, including peak number of deaths per day, date of peak, and duration within most deaths occur. While our main goal is to present the general idea of the simple modeling process using GMs, we also describe possible estimates for the number of required respiratory machines and the duration left until the number of infected will be significantly reduced.

Accurate inundation maps for flooded wetlands and rivers are a critical resource for their management and conservation. In this paper we automate a method (thresholding of the short-wave infrared band) for classifying inundation, using Landsat imagery and Google Earth Engine. We demonstrate the method in the Okavango Delta, northern Botswana, a complex case study due to the spectral overlap between inundated areas covered with aquatic vegetation and dryland vegetation classes on satellite imagery. Inundation classifications in the Okavango Delta have predominately been implemented on broad spatial resolution images. We present the longest time series to date (1990-2019) of inundation maps at high spatial resolution (30m) for the Okavango Delta. We validated the maps using image-based and in situ data accuracy assessments, with accuracy ranging from 91.5 - 98.1%. Use of Landsat imagery resulted in consistently lower estimates of inundation extent than previous studies, likely due to the increased number of mixed pixels that occur when using broad spatial resolution imagery, which can lead to overestimations of the size of inundated areas. We provide the inundation maps and Google Earth Engine code for public use.

In 1922, Albert Einstein visited Paris and interacted extensively with an illustrious section of the French academia. In overfilled sessions at the Coll\`{e}ge de France and the Sorbonne, Einstein explained his theories of relativity, and prominent physicists, mathematicians and philosophers listened, debated, questioned and explored facets of relativity. The 1922 visit had its echoes in the life and works of many who participated, particularly decisive for Einstein and the philosopher Henri Bergson. This essay examines that eventful visit, focusing on the physical and logical aspects of Bergson's critique, with physics commentaries, linking prominent French physicists and mathematicians Langevin, Painlev\'{e}, Hadamard, Becquerel, Sagnac, and Kastler. I give particular attention to the logical and empirical accuracy of the physics issues involved, delineating Bergson's exact reasoning for his philosophical enthusiasm in Einstein's theory and for the ensuing critique. Bergson's philosophical stand on duration and simultaneity is reassessed in the context of later developments in cosmological physics as well as the wealth of empirical data involving comparison of atomic clocks. Finally we are led naturally to a surprising completion of the philosopher's program on universal time, duration and simultaneity, in harmony with the time of the physicist. In the appendices after the main text I also give the physics background and easily verifiable proofs for the assertions made in the text, pertaining to relativity, simultaneity and time dilation, clearly distinguishing beliefs and facts.

A 'little brother' of pain, itch is an unpleasant sensation that creates a specific urge to scratch. To date, various machine-learning based image classifiers (MBICs) have been proposed for quantitative analysis of itch-induced scratch behaviour of laboratory animals in an automated, non-invasive, inexpensive and real-time manner. In spite of MBICs' advantages, the overall performances (accuracy, sensitivity and specificity) of current MBIC approaches remains inconsistent, with their values varying from ~50% to ~99%, for which the reasons underlying have yet to be investigated further, both computationally and experimentally. To look into the variation of the performance of MBICs in automated detection of itch-induced scratch, this article focuses on the experimental data recording step, and reports here for the first time that MBICs' overall performance is inextricably linked to the sharpness of experimentally recorded video of laboratory animal scratch behaviour. This article furthermore demonstrates for the first time that a linearly correlated relationship exists between video sharpness and overall performance (accuracy and specificity, but not sensitivity) of MBICs, and highlight the primary role of experimental data recording in rapid, accurate and consistent quantitative assessment of laboratory animal itch.

During the casting in a warmer tropical temperature, a setting time delay is required to maintain the workability of the concrete, commonly achieved by the addition of admixtures i.e. silica fume (SF), fly ash (FA), and Plastrocrete®. However, high sugar content Coca-Cola in niche conditions is proposed as an ingredient for delaying concrete setting time in combination with conventional admixtures. This research aims to compare the setting time of admixtures from Coca-Cola and Plastocrete® RT6 plus in concrete mixing with control data of concrete mixed with SF or FA. The second aim is to measure the compression strengths between combinations of Coca-Cola and Plastocrete® RT6 plus. Concretes were produced with admixtures of SF, FA, Plastocrete® RT6plus, or Coca-Cola. The concrete used to control was f'c20 and f'c 25, while other concrete mixes were produced with the addition of Coca-Cola at 0.15% from the weight of cement at variation of moisture treatments. The first method to produce concrete (f'c20+Plas0.23%+Cola0.15% and f'c25+Plas0.23%+Cola0.15%) did not employ water reduction. The second concrete productions (f'c25+Plas0.46%+Cola0.15% and f'c25+Plas0.46%+Cola0.15%) reduced the addition of water at 8.8% (v/w). The first concrete production method had a setting time 44% longer than control. The reduced water concrete in the second productions had a setting time 34% longer than control. Meanwhile, the Plastocrete® RT6 Plus admixture with the reduced water delayed the concrete setting time by 26% longer than control. The delayed setting time of Plastocrete® RT6 Plus admixture with reduction of water was shorter than in the treatment with Coca-Cola. The combination of the addition of Coca-Cola with Plastocrete® RT6 plus by reducing the amount of adding Coca-Cola to 0.10% with Plastocrete® RT6 plus can delay concrete setting time by 51% longer than normal concrete and increase concrete compressive strength by 13% higher than normal concrete. Mixing Coca-Cola with Plastocrete® RT6 plus not only provided an optimal delay effect on setting time but also significantly increase the compressive strength that was desired during the casting in warm tropical weather applied in building construction of Mulawarman University, Samarinda, Indonesia.

Millimeter wave wide-band imaging is widely studied for a variety of applications. However real-time millimeter wave wide-band imaging at frequencies above 30GHz for moving targets in a large field of view has not been realized commercially. A 2D sparse array with transmitter multiplexing is a promising solution to this problem. In this article, a method combining compressed sensing and orthogonal coded multiplexing was proposed, and the imaging performance was analyzed for different reconstruction algorithms and observation matrices by imaging simulation for a continuous object. Also the influence on the dynamic range of the original signal introduced by orthogonal coded multiplexing was studied. This work demonstrated that the proposed method was effective in reconstructing the image with a real-time capability. It is shown that different algorithms and matrices resulted in distinct performances, while the evaluation parameter selection also played a role. This work provided useful instructions for both the hardware and software design of a real-time 3D millimeter wave imaging system in the future.

While the container crane is an important part of daily port operations, it has received little attention compared with other infrastructures, such as buildings and bridges. Crane collapse due to earthquake affects the operation of the port, and indirectly impacts the economy. This study proposes fragility analyses for various damage levels of the container crane that allow the port owner and partners to better understand the seismic vulnerability presented by container cranes. A large quantity of nonlinear time history analyses was applied for a three-dimensional (3D) finite element model to quantify the vulnerability of the container crane in considering the uplift and derailment behavior. The uncertainty of demand and capacity of the crane structures were also considered through random variables, i.e. elastic modulus of members, ground motion profile, and intensity. The results analyzed in the case of a Korean container crane showed that the probability of exceeding the first uplift with or without derailment is shown before the crane reaches the structure’s limit states. This means that under low seismic excitation, the crane might be derailed without any structural damage. But when the crane reaches the minor damage state, it is always coupled with a certain probability of uplift with or without derailment. This study also proposes the fragility curves developed for different structural periods to enable port stakeholders to assess the risk of their container crane.

Real-time evolution of the electron densities under excitations in La₂CuO₄ was calculated by the time-dependent density functional theory (TDDFT). The author found, for the first time, under excitations, the electron cloud of Cu²⁺ changes obviously and the characteristic frequencies are 83 meV and 36 meV, respectively, for two different modes. The results are unexpected and close to that of lattice vibrations. The results show that the electron cloud of Cu²⁺ (just like the lattice) can be the electron-pairing medium in high temperature copper oxide superconductors.

We give an exact mathematical construction of a spacelike order $<$, which is dual to the standard chronological order $\ll$ in the $n$-dimensional Minkowski space $M^n$ and we discuss its order-theoretic, geometrical as well as its topological implications, conjecturing a possible extension to curved spacetimes.

Printed electronic devices are attracting significant interest due to their versatility and low cost; however, quality control during manufacturing is a significant challenge, preventing the widespread adoption of this promising technology. We show that terahertz (THz) radiation can be used for the in situ inspection of printed electronic devices, as confirmed through a comparison with conventional electrical conductivity methods. Our in situ method consists of printing a simple test pattern exhibiting a distinct signature in the THz range that enables the precise characterization of {the static} electrical conductivities of the printed ink. We demonstrate that contactless dual-wavelength THz spectroscopy analysis, which requires only a single THz measurement, is more precise and repeatable than the conventional four-point probe conductivity measurement method. Our results open the door to a simple strategy for performing contactless quality control in real time of printed electronic devices at any stage of its production line.

BACKGROUND Epidemiological sciences have been evolving at an exponential rate paralleled only by the comparable growth within the discipline of data science. Digital epidemiological studies are playing a vital role in medical science analytics for the past few decades. To date, there are no published attempts at deploying the use of real-time analytics in connection with the disciplines of Dentistry or Medicine. AIMS AND OBJECTIVES We deployed a real-time statistical analysis in connection with topics in Dental Anatomy and Dental Pathology represented by the maxillary sinus, posterior maxillary teeth, related oral pathology. The purpose is to infer the digital epidemiology based on a continuous stream of raw data retrieved from Google Trends database. MATERIALS AND METHODS Statistical analysis was carried out via Microsoft Excel 2016 and SPSS version 24. Google Trends database was used to retrieve data for digital epidemiology. Real-time analytics and the statistical inference were based on encoding a programming script using Python high-level programming language. A systematic review of the literature was carried out via PubMed-NCBI, the Cochrane Library, and Elsevier databases. RESULTS The comprehensive review of databases of the literature, based on specific keywords search, yielded 491813 published studies. These were distributed as 488884 (PubMed-NCBI), 1611 (the Cochrane Library), and 1318 (Elsevier). However, there was no single study attempting real-time analytics. Nevertheless, we succeeded in achieving an automated real-time stream of data accompanied by a statistical inference based on data extrapolated from Google Trends. CONCLUSION Real-time analytics are of considerable impact when implemented in biological and life sciences as they will tremendously reduce the required resources for research. Predictive analytics, based on artificial neural networks and machine learning algorithms, can be the next step to be deployed in continuation of the real-time systems to prognosticate changes in the temporal trends and the digital epidemiology of phenomena of interest.

The variability of meteorological parameters such as temperature and precipitation, and climatic conditions such as intense droughts, are known to impact vegetation health over southern Africa. Thus, understanding large-scale ocean–atmospheric phenomena like the El Niño/Southern Oscillation (ENSO) and Indian Ocean Dipole/Dipole Mode Index (DMI) is important as these factors drive the variability of temperature and precipitation. In this study, 16 years (2002–2017) of Moderate Resolution Imaging Spectroradiometer (MODIS) Terra/Aqua 16-day normalized difference vegetation index (NDVI), extracted and processed using JavaScript code editor in the Google Earth Engine (GEE) platform in order to analyze the response pattern of the oldest proclaimed nature reserve in Africa, the Hluhluwe-iMfolozi Park (HiP), during the study period. The MODIS-enhanced vegetation index and burned area index were also analyzed for this period. The area-averaged Modern Retrospective Analysis for Research Application (MERRA) model maximum temperature and precipitation were also extracted using the JavaScript code editor in the GEE platform. This procedure demonstrated a strong reversal of both the NDVI and Enhanced Vegetation Index (EVI), leading to signs of a sudden increase of burned areas (strong BAI) during the strongest El Niño period. Both the Theilsen method and the Mann–Kendall test showed no significant greening or browning trends over the whole time series, although the annual Mann–Kendall test, in 2003 and 2014–2015, indicated significant browning trends due to the most recent strongest El Niño. Moreover, a multi-linear regression model seems to indicate a significant influence of both ENSO activity and precipitation. Our results indicate that the recent 2014–2016 drought altered the vegetation condition in the HiP. We conclude that it is vital to exploit freely available GEE resources to develop drought monitoring vegetation systems, and to integrate climate information for analyzing its influence on protected areas, especially in data-poor counties.

The active layer thickness (ALT) is affected by local soil material and surface vegetation coverage in Tibetan plateau permafrost region. The human activities and engineering construction along the Qinghai-Tibet Highway (QTH) destroyed the surface vegetation coverage, which have seriously influenced the ALT and heat exchange balance. Meanwhile, the changes of the detailed internal structure in the active layer will affect the stability of engineering infrastructure. Ground-penetrating radar (GPR) was used to detect the ALT in the permafrost region. However, researches on the detailed structure of the active layer and spatial variation information of ALT are rare, the main reason given for this is that the lack of advanced imaging techniques to enhance the GPR images. In this paper, the researchers focus on solving this problem by applying the reverse time migration (RTM) method to GPR field data acquired in the Beiluhe region. Analyses of the results led to conclusions as follows: a) The RTM algorithm is proved to be accurate for imaging the characteristics of the active layer through the dielectric constant model obtained by common midpoint and GPR data velocity analysis. b) The result of RTM profiles show the loose structure and graben-like fine internal structure. Combining with drill data and soil materials information, the researchers deduce the graben-like structure might be coarse gravel layer, which may be related to subgrade settlements in some local area. c) The 2D contour maps not only show the spatial variation feature of ALT at two sides of the highway, but also can compensate the defect of the research for single 2D survey line. The ALT is about 0.6~0.8 m in most areas, and about 0.8~0.9 m near the highway at west side of the QTH on the 2D contour maps. From the RTM interpretation profile, the closer to the plash, the deeper thawed active layer. The detailed internal structure of the active layer and 2D contour maps of ALT have great significance for the study of fine internal structure and the characteristic of ALT spatial variation in the Tibetan plateau under the background of climatic change.

The development of efficient luminescent systems, such as microcavities, solid state lasers, integrated optical amplifiers, optical sensors is the main topic in glass photonics. The building blocks of these systems are glass-ceramics activated by rare earth ions because they exhibit specific morphologic, structural and spectroscopic properties. Among various materials that could be used as nanocrystals to be imbedded in silica matrix, tin dioxide presents some interesting peculiarities, e.g. the presence of tin dioxide nanocrystals allows increase in both solubility and emission of rare earth ions. Here, we focus our attention on Er³⁺ - doped silica – tin dioxide photonic glass-ceramics fabricated by sol-gel route. Although the SiO₂-SnO₂:Er³⁺ could be fabricated in different geometrical systems: thin films, monoliths and planar waveguides we herein limit ourselves to the monoliths. The effective role of tin dioxide as luminescence sensitizer for Er³⁺ ions is confirmed by spectroscopic measurements and detailed fabrication protocols are discussed.

Lean is one of the systematic approach to achieve higher value for organizations through eliminate non-value-added activities. It is an integrated set of tools, techniques, and principles designed to optimize cost, quality and delivery while improving safety. In Vietnam, industry waste management and treatment has become serious issue. The aim of this research is to present the effective of Lean application for industrial wastes collecting and delivery improvement. Through a case study, this paper showed the way of Lean tools and principles applied for wastes management and treatment such as Value Stream Mapping, Pull system, Visual Control, and Andon.... to get benefit on both economic and environment. In addition, the results introduced a good experience for Vietnamese enterprises in cost saving and sustainable development in waste management.

We present a first formal analysis of specific and complete local integration. Complete local integration was previously proposed as a criterion for detecting entities or wholes in distributed dynamical systems. Such entities in turn were conceived to form the basis of a theory of emergence of agents within dynamical systems. Here, we give a more thorough account of the underlying formal measures. The main contribution is the disintegration theorem which reveals a special role of completely locally integrated patterns (what we call ι-entities) within the trajectories they occur in. Apart from proving this theorem we introduce the disintegration hierarchy and its refinement-free version as a way to structure the patterns in a trajectory. Furthermore we construct the least upper bound and provide a candidate for the greatest lower bound of specific local integration. Finally, we calculate the i-entities in small example systems as a first sanity check and find that ι-entities largely fulfil simple expectations.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

We propose a novel approach to quantum theory construction that involves solving a maximization problem on the Shannon entropy of all possible measurements of a system, relative to its initial preparation. This maximization problem is additionally constrained by a phase condition that vanishes under measurements. Specifically, enforcing a vanishing U(1)-valued phase constraint leads to standard quantum mechanics, while a vanishing Spin^c(3,1)-valued phase constraint extends the theory to relativistic quantum mechanics and to quantum gravity. The latter scenario derives the metric tensor as an operator via a double-copy mechanism applied to the Dirac current. Significantly, this solution is consistent exclusively in 3+1-dimensions as all other dimensional configurations lead to fundamental obstructions. Finally, the solution uniquely incorporates the SU(3)xSU(2)xU(1) symmetries of the Standard Model. This framework seamlessly integrates fundamental concepts from quantum mechanics, relativistic quantum mechanics, quantum gravity, the dimensional specificity of spacetime, and particle physics gauge symmetries as the solution to a simple entropy optimization problem.

Let Vn(d) denote the least number such that every collection of nd-cubes with total volume 1 in d-dimensional (Euclidean) space can be packed parallelly into some d-box of volume Vn(d). We show that V3(d)=r1−dd if d≥11 and V3(d)=1r+1rd+1r−rd+1 if 2≤d≤10, where r is the only solution of the equation 2(d−1)kd+dkd−1=1 on 22,1 and (k+1)d(1−k)d−1dk2+d+k−1=kddkd+1+dkd+kd+1 on 22,1, respectively. The maximum volume is achieved by hypercubes with edges x, y, z such that x=2rd+1−1/d, y=z=rx if d≥11, and x=rd+(1r−r)d+1−1/d, y=rx, z=(1r−r)x if 2≤d≤10. We also proved that only for dimensions less than 11 there are two different maximum packings, and for all dimensions greater than 10 the maximum packing has the two smallest cubes the same.

It is shown that the gravitational mass-energy defect could be the main cause of Big Bang energy and triggering inflation in the newborn Universe.

Assembly theory provides a promising framework to explain the complexity of systems such as molecular structures and the origins of life, with broad applicability across various disciplines. In this study, we explore and consolidate different aspects of assembly theory by introducing a simplified toy model to simulate the autocatalytic formation of complex structures. This model abstracts the molecular formation process, focusing on the probabilistic control of catalysis rather than the intricate interactions found in organic chemistry. We establish a connection between probabilistic catalysis events and key principles of assembly theory, particularly the probability of a possible construction path in the formation of a complex object, and examine how the assembly of complex objects is impacted by the presence of autocatalysis. Our findings suggest that autocatalysis tends to favor longer consecutive construction sequences in environments with low catalysis probability, while this bias diminishes in environments with higher catalysis probabilities, highlighting the significant influence of environmental factors on the assembly of complex structures.

Object detection is complex and involved diverse requirements for different applications. In critical application such as visual impaired navigation guide and real-time surveillance for instance, identifying a particular object of instance is required and this involved a complex approach for realization. Literatures were reviewed, starting with the application of deep learning techniques for object detection; their gaps were identified and addressed using real-time object detection models literature review. From the review gaps were also detected and addressed using literature review on occlusion detection techniques. Object of instance detection in clustered scene with similar object of interest was identified as an open gap not addressed in the existing literature; even through it is vital for many applications. This research recommended an Occlusion Based Object of Instance Detection (OBOID) technique which used the spatial information to identify instant object of interest in clustered scene with many similarly object of interest. Limitation of the recommended OBOID is that it requires only system where position and distance of object is necessary to inform other decision.

Background and Objectives: Effective strategy to cardiopulmonary resuscitation should be based on tissue perfusion. Our primary aim was to determine the association between capillary lactate values and initial rhythm as well as probability of return of spontaneous circulation in out-of-hospital cardiac arrest patients. Materials and Methods: This prospective observational cohort study included all patients with non-traumatic out-of-hospital cardiac arrest, older than 18 years, resuscitated by a prehospital emergency medical team between April 2020 and June 2021. Capillary lactate samples were collected at the time of arrival and every 10 minutes after first measurement until the time of return of spontaneous circulation (ROSC) or if ROSC was not achieved at time of declaring death on scene. Results: 83 patients were enrolled in the study. ROSC was achieved in 28 patients (33,7%), 21 were admitted to the hospital (26,3%) and 6 (7,23%) of them were discharged from the hospital. At discharge all patients had Cerebral Performance Category Scale 1 or 2. Initial capillary lactate values were significantly higher in patients with non-shockable rhythm compared to the group with shockable rhythm (9,19 +/- 4,6 versus 6,43 +/- 3,81; p = 0.037). A significant difference persisted also in a second value taken 10 minutes after in-itial value (10,03 +/- 5,19 versus 5,18 +/- 3,47; p = 0.019). Capillary lactate values were higher in the ROSC group and non-ROSC group at the time of restored circulation (11,10 +/- 6,59 and 6,77 +/- 4,23, respectively; p = 0,047). Conclusions: Capillary lactate values are significantly lower in patients with a shockable first rhythm in OHCA. There is also a significant connection between a rise in capillary lactate level and ROSC.

The interactive approach implies that a heterogeneous group of actors cooperates to identify, develop, and introduce innovative solutions into the ground. 20-year studies showed this approach as the most suitable to support innovation and knowledge sharing in the agri-food system. With the introduction of the EIP initiative in the EU policy, this approach has become a privileged tool to support innovation within the CAP, via the implementation of Operational Groups. The present study aims to analyse how the interaction process works in the implementation of the OGs in Italy, and its effectiveness. An online survey submitted to 270 OGs and 10 in-depth case studies were used to analyse interaction process and its effectiveness in the Italian OGs. The results show that the EIP AGRI in Italy helped to capture the real issues of farmers and other actors in the rural territories. Furthermore, participation in the OGs supported the creation and strengthening of relationships between partners. The major difficulties were identified in maintaining active interaction in all phases of the projects and with all partners involved and in the traditional approach used for dissemination of results, both within and outside the partnership. The study showed how complex is to describe the processes triggered by the interactive approach, being it influenced by the type of relationships existing between partners and by other external factors.

Why do the eyes remain comparatively large whereas the cornea is reduced in most troglobiont mysids? Are there any important organ size-dependent functions served by non-visual eye rudiments? This issue was approached by measuring eye structures in five troglobiont species of Mysida and two Stygiomysida compared with 14 troglophile and 49 trogloxene Mysida species. The Organ of Bellonci (OB) was found in all Mysida and as first records also in Stygiomysida. The length of OBs increased with individual body length and eye length in four examined species: from postnauplioid larvae to adult stage in a troglophile and a trogloxene mysid species examined; and from juveniles to adults in a troglobiont mysid and a troglobiont stygiomysid. At the interspecific level, eye length was on average 26% shorter at a given body length while the OB was 40% longer at a given body length and 54% longer at a given eye length, respectively, in adult troglobionts compared with trogloxene mysids. The OB is clearly proliferating while the cornea is reduced in troglobionts. This points to sensory functions (possibly together with other functions). The sensory pore organ was found in all 15 Mysida species whose eyes were mounted on slides, and a first record of this organ was also found in Stygiomysida.

The quality of life (QOL) is an important indicator of human satisfaction and wellbeing. QOL is significantly and persistently affected for patients after a cancer diagnosis. Despite some evidence suggesting that psycho-oncologic interventions can provide lasting benefits, the inclusion of such interventions in cancer therapy is not universal. This article overviews known approaches to the evaluation of QOL in cancer patients and various interventions for improving patients’ outcomes with a focus on the Eastern European regional and specific Romanian context. With a mortality rate above and cancer care performance below the EU average and unequally distributed, Roma-nia urgently needs a national coordination program which is discussed in our review highlighting the main psychological tools needed for the assessment and its challenges towards implementing the program. In the end, we suggest some directions for future development of the psycho-oncologic approach in the context of social, policy and unexpected financial challenges the nation provides

The article proposes a method for determining the p-value of correlations in compositional data, i.e., those data that arise as a result of dividing the original values by their sum. Data organized in this way are typical for many fields of knowledge, but there is still no consensus on methods for interpreting correlations in such data. In a space closed by normalizing quantity, correlation coefficients behave differently than under normal conditions: their probabilities of occurrence do not coincide with those inherent in the standard scale of estimates. In the tens of the new millennium, almost all newly emerging methods for estimating correlation in compositional data began to require mandatory log-transformation of the variable values. In the method proposed here there are no log-transformations. We return to the early stages of attempting to solve the problem and rely on negative shifts in correlations in the multinomial distribution. In modeling the data, we use a hybrid method that combines the hypergeometric distribution with the distribution of any other law. During our work on the calculation method, we found that the number of degrees of freedom in compositional data measures discretely only when all the normalizing sums are equal and that it decreases when the sums are not equal, becoming a continuously varying quantity. Estimation of the number of degrees of freedom and the strength of its influence on the magnitude of the shift in the distribution of correlation coefficients is the basis of the proposed method.

W. L. Edge proved that the internal points of a conic in PG(2,5), together with the collinear triples on the non-secant lines, form the Desargues configuration. M. Saniga showed an intimate connection between Desargues configurations and the generalized quadrangles of order two, GQ(2,2), whose representation has been dubbed “the doily” by Stan Payne in 1973. In this paper we prove that the external points of a conic in PG(2,5), together with the collinear and non-collinear triples on the non-tangent lines, form the generalized quadrangle of order two.

The debate about the meaning of life in the literature has been around for a while and portraits a fundamental human need to find a personal path of existence. The meaning of life phenomenon purpose lies in its impact on the psychological wellbeing. Knowing your purpose in life can make it more structured and in balance, therefore more meaningful and comprehensible. However, in the existing body of the academic literature meaning of life is discussed more from the philosophic perspective rather than a practical area, which is not helping to solve the global issues of increasing mental health problems. When social and emotional wellbeing is being affected, it is urgent to apply a practical approach to effectively overcome these states. Introduction of a new, holistic meaning of life model is an attempt to offer a practical solution for society to maintain their mental health through awareness of their life’s purpose. Previously in the pilot study (Dombrovskis, 2017) in a sample group of 100 citizens of Latvia who self-reported being in a crisis situation at the given moment, using qualitive analysis the first component for the model structure was identified – antecedent. In our research antecedent is defined as something that triggers certain action, so in crisis situation person can regain a structure and stability in life. We found 8 different antecedents that trigger behavior of those affected by crisis: achievements; power; success; development; freedom; uniqueness; interesting life and fleeing. To continue to explore other components for our model in the setting of Latvia, this study aims to investigate the demographic and personality related variables that may serve as antecedents and as such become one of component in our model structure. The study used a sample of residents of Latvia representing the total population of 1,110 respondents (633 women, 57%, and 477 men, 43%) who have completed the self-assessment questionnaire Meaning of life scale (MOLS) (online and frontally) designed by the authors on their satisfaction with different factors regarding the meaning of life. Average age of respondents (M=33.88; SD=8,527) varied from 18 to 67. The exploratory and confirmatory analysis confirms the data regarding existence of totally 16 factors: 8 antecedents identified in the pilot study and 8 new antecedents identified in the present study - family relations; level of income; relations with friends/acquaintances; state of health; organization of free time; career growth (achievements); sexual life quality and quality of education. Findings confirm a model’s structure to be complex phenomenon consisting of various components. However, findings suggest that more research should be done to fill the following gaps: 1) identify actions, which are triggered by 16 antecedents; 2) figure out F1, F2 and F3 factor role in the model structure.

The research presented in this paper concerns the determination of the attraction basins of the Newton’s iterative method which was used to solve the non-linear systems of observational equations associated with the geodetic measurements. The authors considered simple observation systems corresponding to the intersections, or linear and angular resections, used in practice. The main goal was to investigate the properties of the sets of convergent in the initial points of the applied iterative method. An important issue regarding the possibility of automatic and quick selection of such points was also considered. Therefore, the answers to the questions regarding the geometric structure of the basins, their limitations, connectedness or self-similarity were sought. The research also concerned the iterative structures of the basins, i.e. maps of the number of iterations which are necessary to achieve the convergence of the Newton’s method. The determined basins were compared with the areas of convergence that result from theorems on the convergence of the Newton’s method, i.e. the conditions imposed on the eigenvalues and norms of the matrices of the studied iterative systems. One of the essential results of the research is the indication that the obtained basins of attraction contain areas resulting from the theoretical premises and their diameters can be comparable with the sizes of the analyzed geodetic structures. Consequently, in the analyzed cases it is possible to construct methods that enable quick selection of the initial starting points or automation of such selection. The paper also characterizes the global convergence mechanism of the Newton’s method for disconnected basins and, as a consequence, the non-local initial points, i.e. located far from the solution points.

Disruptive technologies can be conceptualized in different ways. Depending on how they are conceptualized, different ethical issues come into play. This article contributes to a general framework to navigate the ethics of disruptive technologies. It proposes three basic distinctions to be included in such a framework. First, emerging technologies may instigate localized “first-order” disruptions, or systemic “second-order” disruptions. The ethical significance of these disruptions differs: first-order disruptions tend to be of modest ethical significance, whereas second-order disruptions are highly significant. Secondly, technologies may be classified as disruptive based on their technological features or based on their societal impact. Depending on which of these classifications one adopts and takes as the starting point of ethical inquiry, different ethical questions are foregrounded. Thirdly, the ethics of disruptive technology raises concerns at four different levels of technology assessment: the technology level, the artifact level, the application level, and the society level. The respective suitability of approaches in technology ethics to address concerns about disruptive technologies co-varies with the respective level of analysis. The article clarifies these distinctions, thereby laying some of the groundwork for an ethical framework tailored for assessing disruptive technologies.

A large number of smart devices (things) are being deployed with the swift development of Inter- net of Things (IOT). These devices, owned by different organizations, have a wide variety of services to offer over the web. During a natural disaster or emergency (i.e., a situation), for example, relevant IOT services can be found and put to use. However, appropriate service matching methods are required to find the relevant services. Organizations that manage situation responses and organizations that provide IOT services are likely to be independent of each other, and therefore it is difficult for them to adopt a common ontological model to facilitate the service matching. Moreover, there exists a large conceptual gap between the domain of discourse for situations and the domain of discourse for services, which cannot be adequately bridged by existing techniques. In this paper, we address these issues and propose a new method, WikiServe, to identify IOT services that are functionally relevant to a given situation. Using concepts (terms) from situation and service descriptions, WikiServe employs Wikipedia as a knowledge source to bridge the conceptual gap between situation and service descriptions and match functionally relevant IOT services for a situation. It uses situation terms to retrieve situation related articles from Wikipedia. Then it creates a ranked list of services for the situation using the weighted occurrences of service terms in weighted situation articles. WikiServe performs better than a commonly used baseline method in terms of Precision, Recall and F measure for service matching.

A close analysis of the text of Gen. 2:8-15, pertaining to the garden of Eden, shows the structural differences between said text and others from ancient mythologies that mention or describe a paradise. Likewise, that analysis suggests that the data provided by the Bible to locate paradise is merely a narrative device meant to dissipate all doubts as to the existence of the garden where God put human beings. Similarly to other spaces that appear in the Bible, the garden of Eden is but an impossible place. Throughout the centuries, however, recurring proposals have been made that aim to find paradise. As time went by, those proposals were progressively modified by the intellectual ideas dominant at any given era, thus leading the representations of the location of Paradise further and further away from the information provided by the biblical text.

A good management of diabetes requires at the same time self-regulation behaviour and a balanced involvement of family components. This study’s aims were: understanding fear of injections and perceptions of family conflicts in preadolescents and adolescents with type 1 diabetes mellitus and their mothers, comparing their perceptions, and identifying the risk factors impacting patients’ quality of life. Participants were one hundred and two patients (Mean age = 14.63, SD = 2.43; age range = 10-19 years; Females = 52) and their mothers (Mean age = 46.94, SD = 6.2, age range = 27-63 years), who filled in self and proxy-report questionnaires. Twenty % of patients and 14.7% of their mothers reported clinical score for fear of self-injection and blood testing. Mothers reported higher fear of injecting and family conflicts compared with the patients. Age, fear of injecting and family conflicts impacted significantly on patients’ quality of life perceptions. Clinical consideration and recommendations are given basing on the empirical results.

Around one billion people live in informal settlements, globally, including over half of Nairobi, Kenya’s three million residents. The purpose of this study was to explore women’s fear of victimization within Mathare, an informal settlement in Nairobi, Kenya and how fear of victimization influences behavior. Fifty-five in-depth interviews were conducted with women in 2016. A modified grounded theory approach guided data collection and analysis. Findings suggest fear of victimization is a serious concern in informal settlements. Women have found ways to adopt their behaviors that allow them to continue to function and protect their children despite fearing victimization, but at a potential cost to their health and well-being. Thus, there is a critical need for more research focused on social, economic, structural, community, infrastructure, technological, and individual strategies to prevent violence, enhance residents’ sense of safety, and, subsequently, minimize women’s fear of victimization in informal settlements.

The "best of all possible worlds" theory (hereinafter the "possible world theory") was presented by Leibniz many centuries ago, and provided an opportunity for metaphysics to understand the ontological meaning of the world in an in-depth way. Furthermore, the theory has multiple impacts on the multiverse theory of modern physics. However, considering the ontological questions of the world solely on linguistics logic leads to basing the possible world theory or the multiverse theory on relatively uncertain inferential reasons. In this study, symbolic logic was used to consider the possible world theory on a more solid foundation. The entire world was made into oneness, and tracking the existential process at the beginning of the world, realized the existential necessity of the world, even though the initial causal point of the world was assumed to be completely void (null set). The existential system in this study, was generalized without specific elements, apart from existence and non-existence. It was discovered that existential possibility and existential necessity are logically equivalent.

We present the detailed calculations of social distancing requirement. A comparative study of the growth pattern and death tolls in different communities indicates that the growth pattern of infected patients and death rate follow the similar distribution with different parametrizations. Every distribution follows an exponential growth pattern curve, like other microbes, then reaches the saturation point an d eventually decay s However, the argument for the exponential function depends on several parameters unbeknownst, as of yet. However, the slope varies different ial ly for various epicenter s and seems to have a relationship with parameters such as accessibi lity to healthcare facilities, pre existing medical conditions socio economic conditions and lifestyle. The mismatch of the growth pattern is also linked with the impact of various other factors and a premature interpretation of limit ed data. Novel behavi or of the virus brought many surprises, opened up new venues for medical research, and the need for the more detailed study of pathogens in the light of the interaction of RNA and DNA The adaptability to diverse ecological condition s and the relevant modification in the structure is also worth investigation The genetic modification can be studied using quantum mechanical probabilistic approach.

In this study, differences in the kinetics of thermal-supported hydrolytic degradation of poly(lactic acid) (PLA) sample wet spinning fibres due to material variance in the initial molecular and supramolecular structure were analysed. The investigation was carried out at the microstructural and molecular levels by using readily available methods such as scanning electron microscopy, mass erosion measurement and estimation of intrinsic viscosity. The results show a varying degree of influence of the initial structure on the degradation rate of studied PLA fibres. The experiment shows that hydrolytic degradation at a temperature close to the cold crystallization temperature on a macroscopic level is definitely more rapid for the amorphous material, while on a molecular scale it is similar to a semi-crystalline material. Further, for the adopted degradation temperature of 90 °C, a marginal influence of pH of the degradation medium on the degradation kinetics was also demonstrated

Our main objective in this work was to examine the possibility of non-intrusive, label-free, detection of whole Zika viruses using terahertz signals with or without a targeting/binding oligonucleotide (aptamers). We report for the first time the use of terahertz electromagnetic waves (0.75 THz – 1.1 THz) to detect Zika viruses. The Zika/aptamer complexes showed a reproducible terahertz reflection coefficient minimum at 1.064 THz while the Zika virus’s reflection minimum was at 1.073 THz. Of different substrates we examined, the polyester petri dish provided a very low loss and excellent terahertz transmission. To increase the interaction between the terahertz signal and the sample we also used polyester microbeads coated with aptamers. We then measured the terahertz reflection from the microbeads as a function of Zika concentration. The resulting terahertz Zika sensor had sensitivity of 63 Hz/Zika and minimum detectable signal of ~ 16x10³ Zika. Other substrates such as Graphene on polyethylene terephthalate (PET), 50 nm-thick gold film on polycarbonate, thin (30 um-thick) glass slide and Teflon were also examined. Graphene substrate enabled direct detection of the Zika without any aptamers.

In nowadays conditions, insurance provides the opportunity for market system of economic management to work in any state. To provide economic security of the person it is needed to create a mechanism of protection against internal and external threats in modern Russia. That’s why the role of citizens insurance policy is increasing as the most effective risk management institute and achieving safety of health and private property of citizens. The goal of this research is to study Russian citizens’ attitudes towards insurance policy and investment using the conception of personal economic security. The preparatory study stage was focused on theoretical understanding of economic security problems taking insurance field as an example. Empirical research consisted of four stages. There were 1793 people taking part in this research. Results of this study can be proposed in the program of improving the functioning of the insurance market in the Russian Federation in The framework of the strategy of development of the insurance market - 2020. The obtained results can be used in Politics and Economics in the development of a set of measures related to lawmaking, control of financial institutions, promotion of financial literacy of the population, preparation of courses for universities and trainings for participants of the insurance market. The typologies of policyholders which were given can be the basis to create insurance programs for the citizens.

A recently developed thermodynamic theory for the determination of the driving force of crystallization and the crystal–melt surface tension is applied to the ice–water system employing the new Thermodynamic Equation of Seawater TEOS-10. The deviations of approximative formulations of the driving force and the surface tension from the exact reference properties are quantified, showing that the proposed simplifications are applicable for low to moderate undercooling and pressure differences to the respective equilibrium state of water. The TEOS-10 based predictions of the ice crystallization rate revealed pressure-induced deceleration of ice nucleation with an increasing pressure, and acceleration of ice nucleation by pressure decrease. This result is in, at least, qualitative agreement with laboratory experiments and computer simulations. Both the temperature and pressure dependencies of the ice–water surface tension were found to be in line with the le Chatelier–Braun principle, in that the surface tension decreases upon increasing degree of metastability of water (by decreasing temperature and pressure), which favors nucleation to move the system back to a stable state. The reason for this behavior is discussed. Finally, the Kauzmann temperature of the ice–water system was found to amount TK=116K, which is far below the temperature of homogeneous freezing. The Kauzmann pressure was found to amount pK=-212MPa, suggesting favor of homogeneous freezing upon exerting a negative pressure on the liquid. In terms of thermodynamic properties entering the theory, the reason for the negative Kauzmann pressure is the higher mass density of water in comparison to ice at the melting point.

Traditionally understood in reference to distance education, cognitive presence may be defined as "the extent to which the participants in any particular configuration of a community of inquiry can construct meaning through sustained communication. The purpose of this paper was to create a blueprint for the reflective ePortfolio as the capstone project for my graduate degree. The blueprint was accomplished by adapting for use cognitive presence as a tool for both analysis and framing, which has never been done to the best of my knowledge. I considered myself to be a participant in a “community of inquiry” model and substituted the result of my interaction with each of the required instructor-course content pairings I took to serve as fellow participants in this community model. The result of my participation was understood to be the knowledge and experience that I have gained, which was reflected in eight of my academic research papers. These selected papers were the artifacts around which my ePortfolio was ultimately developed and demonstrated my participation as an active member in this community of inquiry constructing meaning through sustained communication.

The accurate monitoring of state of charge (SOC) and state of health (SOH) is critical for the reliable management of lithium-ion battery (LIB) systems. In this paper, the online model identification is scrutinized to achieve high modeling accuracy and robustness, and a model-based joint estimator is further proposed to estimate the SOC and SOH of LIB concurrently. Specifically, an adaptive forgetting recursive least squares (AF-RLS) method is exploited to optimize the estimation alertness and numerical stability, so as to achieve accurate online adaption of model parameters. Leveraging the online adapted battery model, a joint estimator is proposed by combining an open-circuit voltage (OCV) observer with a low-order state observer to co-estimate the SOC and capacity of LIB. Simulation and experimental studies are performed to evaluate the performance of the proposed data-model fusion method. Results suggest that the proposed method can effectively track the variation of model parameters by using the onboard measured current and voltage data. The SOC and capacity can be further estimated in real time with fast convergence, high accuracy and high stability.

In this paper, the authors seek to discuss some of the complexities involved in cross-cultural working in relation to the communication and management of pain in older people. Specifically, the paper addresses the culture construction of ageing and how pain is often constructed as a natural part of ageing. The authors also suggests that with the rise of the ideology of active-ageing many older people who are disabled or living in chronic pain, may feel a moral imperative to hide pain and ill-health. The discussion extends into looking at the impact of culture and the communication of pain, including specific idioms of distress, somaticize and the lay-management of pain through stoicism.

Understanding the vulnerability of areas and the likelihood of specific disasters, particularly earthquakes, is one of the most important issues in Iran. One of the major concerns in Iran is the resilience of rural communities. The present study is devoted to spatial analysis of risk in rural areas and the evaluation of preparedness in the rural districts of the city of Abhar. In particular, this study evaluates the resilience to earthquakes. The research was conducted in two parts in which the first part has used the VIKOR Multiple criteria decision making model as well as the employment of this model in the ArcGis. The second part of the study used field studies, in the form of questionnaires, to evaluate the readiness of the local population against the risks of earthquakes. Four indicators, individual, physical, economic abilities and access, were assessed. The population included rural districts, where statistical samples were villagers. Results of the spatial analysis indicated that 15 villages are in the high-risk areas, 24 villages were in the medium-risk areas and all other villages were in low-risk areas. In terms of readiness of the locals, the results indicated a lack of planning with regards to the four mentioned indicators.

A new clothing resistance model is described and applied to characterize the human thermal and moisture climates. The climate was described by the thermal (rcl,t) and evap-orative (rcl,e) resistances of comfortable, imaginary clothing. The key input variable of the model is the rate of sweating (λEsw). Since sweating is an individual-specific process, the model applies to the individual. The observations were carried out by a single individual in Martonvásár (Hungarian lowland, Central Europe) in the summer of 2023 and the winter of 2024. During the observations, the observer walked at a speed of 1.1-1.7 ms-1 in weather-appropriate clothing. Among the results, we would highlight the following: Dur-ing large environmental heat surpluses, the rcl,t values were found to be between 0.1-0.5 clo-t (clo-t = 0.155 m2·℃·W-1), while the rcl,e values fell between 0.4-0.8 clo-e (clo-e = 0.155 m2·hPa·W-1). The values of the parameters close to 0 were caused by intense sweating (λEsw > 200 Wm-2). The applicability of the model is limited and largely depends on the rela-tionship between λEsw and the metabolic heat flux density.

This study delves into the essential characteristics of the Metaverse and its impact on the real world. The Metaverse, a parallel universe composed of countless 3D virtual worlds, has become a hot topic in technology. With the development of advanced technologies such as Virtual Reality (VR), Augmented Reality (AR), blockchain, and Artificial Intelligence, the Metaverse is gradually changing people's lifestyles and work methods, expanding the boundaries of the digital economy. This study profoundly investigates the attributes of the Metaverse, such as asset digitization, application scenario-based, scope economy, industry universality, integrated innovation, and the platform ecosystem. Additionally, we propose a theoretical framework to aid in understanding and shaping this emerging field. We conducted a thorough study and analysis of a specific case, explored the key features of the Metaverse, unveiled the profound impact of Metaverse characteristics on social and economic development, and verified our theoretical framework with this case. This research provides new perspectives and methods for academic studies and offers robust support and guidance for practical applications and decision-making.

In this manuscript we use an exactly solvable stochastic binary model for regulation of gene expression to analyse the dynamics of response to a treatment aiming to modulate the number of transcripts of RKIP gene. We demonstrate the usefulness of our method simulating three treatment scenarios aiming to reestablish RKIP gene expression dynamics towards pre-cancerous state: i. to increase the promoter’s ON state duration; ii. to increase the mRNAs’ synthesis rate; iii. to increase both rates. We show that the pre-treatment kinetic rates of ON and OFF promoter switching speeds and mRNA synthesis and degradation will affect the heterogeneity and time for treatment response. Hence, we present a strategy for reducing drug dosage by simultaneously targeting multiple kinetic rates. That enables a reduction of treatment response time and heterogeneity which in principle diminishes the chances of emergence of resistance to treatment. This approach may be useful for inferring kinetic constants related to expression of antimetastatic genes or oncogenes and on the design of multi-drug therapeutic strategies targeting master regulatory genes.

Derivation of light paths in the Michelson interferometer is based on the hypothesis that the speed of light does not change after reflection by a mirror in motion. The Michelson-Morley experiment predicts a fringe shift of 0.40. The same fringe shift is predicted for a particular Michelson interferometer in which the beam splitter of the interferometer makes an angle of 45° with the direction of light from the source. Light behaves like a wave and also as a particle. Thus, it is reasonable to consider the reflection of light as a mechanical phenomenon. With this hypothesis, the speed of light changes after reflection, and the predicted fringe shift for the particular Michelson interferometer is zero which is in accordance with the result of the Michelson-Morley experiment. Apparently, light travels in any inertial frame as if this particular interferometer belongs to a fixed frame. The velocity of light is considered independent of the velocity of its source, which is in accordance with astronomers’ observations of the binary stars, and the experiment performed at CERN, Geneva, in 1964.

This article reevaluates the Woesean concept of crossing a ‘Darwinian threshold’ from pre-genomic communality, as prevailing in an ancestral ‘progenote’ state, to vertically stable lineages of autonomous and self-similar cells. This transition from collective trunk-line evolution to Darwinian speciation is dependent on the generation of modular organismal genomes. The same general principle should be valid at subcellular levels, allowing the emergence of semi-autonomous genomic agents, such as viruses and plasmid-carrying endogenous vesicles with organelle-like properties. As compartmentalized agents of endogenous nature could start with smaller genomes than those required for fully autonomous cells, it is conjectured that stable subcellular lineages emerged earlier than their cellular counterparts. Referring to the recent ‘pre-endosymbiont hypothesis’, it is proposed that free-living bacteria (the first ‘prokaryote’ cells) arose by ‘lineage escape’ from plasmid-bearing organelle-like compartments, evolving inside the internally complexifying ‘paracells’ of the progenote community. The double-membrane envelopes of diderm bacteria may have resulted from cell-biological processes facilitating cellular lineage escape. The later emergence of archaeal cells (resembling bacteria in ‘prokaryote’ appearance with unichromosomal genomes) and eukaryotic organisms (with compartmented cells and multichromosal genomes) can also be interpreted in terms of this modified progenote hypothesis. Conceivably, the multichromosomal genomes of eukaryotes were bundled in endogenous nuclear compartments to organize a ‘nuclear-cytoplasmic lineage’, which became vertically stable by perfecting mitosis/meiosis-like divisions and yet retained some intra-species population confluence by sexual division-fusion cycles.

Paving blocks are concrete pieces placed in exposed places to the weather, which are sub-jected to loads and wear. Hence, quality control in the manufacture of paving blocks is es-sential to guarantee the properties and durability of the product in construction projects. In Ecuador, the requirements are described in the Ecuadorian technical standard "NTE INEN 3040", and tensile splitting strength is a fundamental requirement to guarantee product quality. It is analyzed using quality control measurements such as dimensions, the weight of the fresh paving block in the vibro-compacted process, and the percentage of water absorption in order to know how the variables influence and manage to predict the tensile splitting strength to avoid product non-conformity in advance, having a timely and better control of the manufacturing process. The data was obtained from a company that can produce 30 000 units per day of rectangular paving blocks with 6 cm thickness. Mul-tivariate models such as multiple linear regression, regression trees, random forests and neural networks are performed to predict the tensile splitting strength variable through two groups of predictors; the first group is the thickness mm, width mm, length mm, mass of fresh paving block g and percentage of water absorption %. The second group of pre-dictor variables is the density of the fresh paving block kg/m3 and the percentage of water absorption %. It is concluded that the multiple linear regression method performs better in predicting the first group of predictor variables with a mean square error (MSE) of 0.110086, followed by the neural network without hidden layers resulting in an MSE of 0.112198. The best method for the second set of predictors was the neural network with-out hidden layers with a mean square error ( MSE ) of 0.112402, closely followed by the multiple linear regression model with an MSE of 0.115044.

Perhaps the greatest challenge in the graft copolymerization of acrylic acid onto starch initiated by Fenton’s is the selectivity of the grafting reaction. Low selectivity means that too much of unwanted homopolymer polyacrylic acid is produced. In this paper, it has been analyzed why with this reaction system, involving a water soluble monomer and indirect initiation, the graft selectivity is such a challenge. Several other grafting reactions, especially with monomers of low water solubility or when direct initiation is applied, show a better grafting performance. A scheme is presented based on reaction engineering principles, that supports an explanation of the observed differences. A more selective activation of starch is a factor, but perhaps even more important is a low monomer to starch ratio at the starting sites of graft reactions. Based on these insights, several methods to improve the graft selectivity are evaluated, with the help of literature data but mostly by experimental explorations in our laboratory. Most promising appears to be a dedicated dosage method, to add monomer in portions over time, tested in a batch reactor with gelatinized cassava starch. This way, both grafting percentage and graft selectivity could be improved. Such could not be realized with the more conventional dosage, which is to add all monomer before the start of the reaction. This can be considered a principal breaktrough. Still, more research and development would be needed to refine the method and to implement the idea also in a continuous reactor at larger scale.

The poor solvent crystallization of carbapenem CS-023 has been performed at 25 °C. The following results have been obtained: 1) A solvate crystal Form A (5/2 Ethanol·1/2 H2O) is recovered from 80 v/v% ethanol solution, 2) Form A transforms to Form H (4H2O) by the solid-phase transition through the solvate-free polymorph, Form A-2, and Form A also transformed to Form C (1Ethanol·3H2O) by the solvent-mediated transformation. In the present study, we found that Form C also transforms to Form H by the solid-phase transition through the solvate-free polymorph, Form C-2. The three polymorphs, Form A, H, and C, were composed of the helical-chain structures, respectively. However, there was an incomprehensible affair in the solid phase transition among the three polymorphs. Namely, Form A comprised a left-handed helix.On the other hand, Form C and Form H’s helix chains were in a left- and right-handed helix complex. The solid-phase transition of Form A into Form H suggested the switch of helicity in the solid. We attempted to explain the helicity change in the solid phase transition. As a result, it was suggested that the over-absorption of water of Form A-2 at high humidity plays a vital role in the helicity change.

In physics, thought experiments are impressive heuristic tools. They are valuable instruments to help scientists find new results and to teach students the known ones. However, as we shall show, they should always be received with prudence, even when they are a shortcut to 'prove' well-established results. Here, we show that the most widely known thought experiments devised to derive the gravitational frequency shift from energy conservation are, in fact, problematic. When properly set and correctly read, those thought experiments reveal that the existence of the gravitational frequency shift is, in fact, at odds with energy conservation. We also propose two new simple thought experiments, one using the conservation of energy and the other the conservation of linear momentum, that corroborate that conclusion, showing that those conservation principles do not imply the gravitational frequency shift. We think that our results may be of some epistemological interest and could serve as a warning sign on how thought experiments should be received and trusted.

The development of sustainable tourism in the territory requires the monitoring of all diverse aspects of the tourism sector and the creation of information technologies that provide the collection, analysis, processing and visualization of relevant information. The aim of this work is to describe the concept of the tourism monitoring service in Irkutsk Oblast as part of the Lake Baikal area, define methods and software of implementing this service, and present individual results of its prototyping. The creation of a service includes the development and software implementation of methods for collecting, processing and visualizing data, as well as ensuring the use of the functionality of existing cloud platforms for the main information processes. Data collection methods are based on Application Programming Interface and web scraping technologies, processing methods include statistical methods and artificial intelligence methods, visualization methods are based on Business Intelligent systems methods. In this paper described the concept of service, justified methods of data analysis and visualization, built an ontological model, defined the content of dashboards, implemented a prototype of a service, and demonstrated the results of data collection, processing and presentation obtained from the research. Currently, information has been collected and processed for the following tourist attractions: 685 accommodation facilities, 16 services, 809 catering establishments, 352 attractions, 94 tourist routes and excursions. The proposed technology (methods and software) of the territory tourism monitoring service has demonstrated its effectiveness.

Aymaraism, as a socio-cultural phenomenon, has given rise to components and elements of representativeness in the population of the Andes. However, the dialectic component of the Aymara as a nation is annulled by fundamental historiographical elements that underlie this process of identification. The empirical analysis of the historical data leads us to conclude that the Aymara language and culture contain ambiguous elements that cannot be defined according to the dialectical interpretation and the current narrative. Thus, the analysis of the cultural, linguistic and social elements of this population from the Early Horizon period to the present confirms the historical distortion towards a narrative component of origin and presence in the territory of the Qullasuyu, in the current geographical area of the Collao. In order to understand this phenomenon, this work promotes the complementarity of the analysis through the use of ethnoarchaeological and documentary elements in order to clarify the origin, synthesis and development of the Aymara from a historical perspective, leaving aside the dialectical component of the present.

The pride of power of the Spanish preachers of religious art is reflected in the church of Santo Domingo built between 1541 and 1688. This work of heritage architecture, one of the first to be built in the colonized city, was affected by multiple earthquakes, interventions, and constructions that do not have a clear record. A total of 13 samples were taken from the lining mortar inside the cloister, central nave, and side chapel, following the nondestructive testing protocols and standards suggested by the research team. The analysis included mineral characterization studies and quantitative analysis by X-ray diffraction and scanning electron microscopy with microanalysis of the samples. The results showed the presence of volcanic aggregates and lime lining and joint mortars, mortars of rustic composition and coarse manufacture. The resolution of the data of mineralogical composition and texture has allowed us to corroborate the historical information described by the chroniclers and to date relatively the studied sites and to establish a hypothesis of constructive stages.

One of the problems, which make it difficult to solve the mystery of the origin of life, would be how life emerged in chemically complex messy environments on the primitive Earth. It is considered that three main points contributed to open the way to the emergence of life. (1) A characteristic inherent in [GADV]-amino acids, which are easily produced with prebiotic means. (2) Protein 0th-order structure or [GADV]-amino acid composition generating water-soluble globular protein with some flexibility, which can be produced even by random joining of [GADV]-amino acids. (3) Formation of versatile [GADV]-microspheres, which can grow, divide, proliferate even without genetic system, was the emergence of proto-life. (4) [GADV]-microspheres with a higher proliferation ability than others could be selected. The proto-Dawin evolution made it possible to proceed forward to creation of the core life system composed of (GNC)n gene, anticodon stem-loop tRNA or AntiC-SL tRNA (GNC genetic code) and [GADV]-protein. (5) Eventually, the first genuine life with the core life system emerged. Thus, the formation processes of [GADV]-protein and (GNC)n gene in chemically complex messy environments were the steps to the emergence of genuine life.

(1) Aim of the study was to investigate the spatial and temporal characteristics of the airflow created by two commercially available non-contact tonometers, the CorvisST and the Ocular Re-sponse Analyser. (2) The airflow pressure was measured using a MEMS pressure sensor to inves-tigate the spatial and temporal distribution. The airflow from the CorvisST and Ocular Response Analyser were mapped to a 600µm and a 1mm resolution grid, respectively. (3) Central airflow pressure of the CorvisST (96.4 ± 1.4)mmHg was higher than the Ocular Response Analyser (91.7 ± 0.7)mmHg. The duration of the air-puffs also differed, with the CorvisST showing a shorter du-ration (21.483 ± 0.2881)ms than the ORA (23.061 ± 0.1872)ms. The rising edge of the CorvisST airflow pressure profile demonstrated a lower gradient (+8.94mmHg/ms) compared to the Oc-ular Response Analyser (+11.00mmHg/ms). Both had similar decay response edges; CorvisST -11.18mmHg/ms, Ocular Response Analyser -11.65mmHg/ms. (4) The study presents a valid method to investigate physical dimensions of the airflow pressure of non-contact tonometers. Novel findings relating to the magnitude, duration and spatial characteristics of the respective airflow pressures are reported. It is anticipated that this information will better inform clinical studies and theoretical models relating to ocular biomechanics.

The paper presents Jonathan Swift's Gulliver's Travels as the first attempt to claim that thought experiments, namely the close analysis of contrived counterfactual scenarios, are the only way we challenge normative framework assumptions and learn anything significantly new in and outside science. The standard epistemologies of his day – Baconian empiricism and Cartesian rationalism –fiercely ridiculed in the course of Gulliver's third voyage, are cruelly dismissed as powerless to advance knowledge, and keep it in normative check. The transformative effect of the clever thought experiments presented in the three other voyages (of imagining London shrunk to a twelfth of its size and enlarged to giant proportions, and a more responsible and intelligent race of beings inserted above (normally sized) humans) enable Swift to obtain critical normative distance from several major assumptions about politics, religion, aesthetics, ethics, and much more, including the limits of the thought experiment itself. In the second part of the paper, the impressivre use to which the Talmudic literature puts such imagined counterfactual scenarios, is examined, with special reference to ethics and law.

This work aims to investigate the effect of process temperature and catalyst content by thermochemical degradation of municipal solid waste (MSW) fraction (organic matter + paper + plastic) on the yield of reaction products (bio-oil, biochar, H2O and gas), physi-cochemical properties and chemical composition of bio-oils, as well as on the morphol-ogy and crystalline phases of biochar in laboratory scale. The organic matter, paper and plastic segregated from the gravimetric composition of total waste sample were subject-ed to the pre-treatments of drying, crushing and sieving. Thermal pyrolysis was per-formed at 400, 450 and 475 °C and 1.0 atmosphere, and catalytic pyrolysis at 450°C and 1.0 atmosphere, using 5.0, 10.0 and 15.0% (wt.) of FCC zeolite, bath mode, using a laboratory-scale borosilicate glass reactor. The bio-oil was characterized for acidic val-ue. The chemical functions present in the bio-oil identified by FT-IR and the composi-tion by GC-MS. Biochar was characterized by SEM/EDS and XRD. Thermal pyrolysis of the MSW fraction shows bio-oil yields between 9.44 and 9.24% (wt), aqueous phase yields between 21.93 and 18.78% (wt), solid phase yields between 67.97 and 40.34% (wt) and gas yields between 28.27 and 5.92% (wt). The bio-oil yield decreased with in-creasing process temperature. For the experiments using FCC, the biochar and gas yields slightly increased with increasing FCC content, while that of bio-oil decreased and the H2O phase remained constant. GC-MS of bio-oils identified the presence of hy-drocarbons and oxygenates, as well as nitrogen-containing compounds including am-ides and amines. The acidity of the bio-oil increased with increasing temperature and with the aid of FCC as a catalyst. The presence of hydrocarbons in bio-oil was identified by the addition of FCC catalyst due to the deoxygenation of carboxylic acids, followed by decarboxylation and decarbonylation reactions, producing aliphatic and aromatic hydrocarbons.

This paper focuses on determining the State of Charge (SOC) of lithium-ion batteries when operating and the influence the State of Health (SOH) has on SOC determination. The paper studies the effects of the discharge rate on the battery performance and how it modifies the evaluation of the SOC. The article also analyzes the effects of battery aging on the determination of SOC. The online determination of SOC in lithium-ion batteries uses the linear behavior of battery discharge and how the discharge rate modifies the battery voltage slope. The paper develops a simple algorithm that relates the SOC of the battery with the online battery voltage. The proposed measurement method uses a very short controlled discharge at a specific rate that avoids unexpected interferences with the current operation of the battery during charge or discharge. We conducted a simulation process to evaluate the evolution of the SOC in Li-ion batteries for different operating stages. Experimental tests validate the proposed methodology, showing a close agreement between theoretical values and experimental results with 98% accuracy. The paper also deals with the determination of the aging factor in lithium batteries as a critical parameter to calculate the SOC. The method determines the aging factor using specific simulation for this goal. The results are compared to values obtained in an experimental test within high agreement (>93%). The proposed model applies to almost any lithium battery and is validated for a wide range of Battery State of Health, up to 50%, within accurate prediction, higher than 90%.

We hypothesize that the first ancestral "ante-cell" molecular structures, i.e., first RNAs and peptides which gradually transformed into real cells once the Earth had cooled sufficiently for organic molecules to appear there, have leaved traces in RNAs and genes of present cells. We propose a circular RNA which could have been one of these ancestral structures whose vestigial pentameric subsequences would mark the evolution from this key moment when the ante-cells have begun to join the living organisms. In particular, we propose that in present RNAs (ribosomal or messenger) playing an important role in the metabolism of current cells, we look for traces of the proposed primitive structure in the form of pentamers (or longer fragments) belonging to their nucleotide sequence. The result obtained can be summarized in the existence of a gradient of occurrence of such pentamers, with a high frequency for the most vital functions (protein synthesis, nucleic synthesis, cell respiration, etc.). This gradient is also visible between organisms, from the oldest (Archaea) to the most recent (Eukaryotes) in evolution of species.

This review paper explores the multifaceted landscape of digital heritage preservation and presentation, focusing on various methods and technologies employed in the field. The introduction highlights the significance of digital heritage in preserving and showcasing cultural, historical, and natural assets. It emphasizes the non-destructive nature of digital preservation methods, enabling wider access and research possibilities. The paper also discusses the relevance of cultural computing in creating engaging user experiences and recognizes its potential in bridging cultural gaps. The literature review section presents a diverse range of technologies and tools, such as ZENetic Computer, C-Vyasa Sanskrit, Pandulipi Samshodhak, JATAN, and immersive projects like "Alice in Wonderland." The methods and technologies section delves into the technical aspects of digital heritage preservation. It explores photogrammetry, 3D depth sensing, 3D laser scanning, augmented reality, digital storytelling, focus stacking, and multiple view stereovision. Each technology is discussed in detail, highlighting its applications, benefits, and relevance in cultural heritage preservation. Finally, the comparative analysis section offers insights from various research papers and books, comparing different methodologies and approaches in the field. This review paper provides a comprehensive overview of digital heritage preservation, showcasing the diverse methods and technologies that contribute to the safeguarding and presentation of our cultural heritage for future generations.

For the first time, the effect of a significant change in the resistance of the aquatic environment of a population of protozoan microorganisms under the influence of radiofrequency electromagnetic radiation from cell phones has been experimentally studied. The results of the experiment demonstrate the biological nature of the changes occurring in the “water population of protozoa” system, which indicates that the impact of radiation directly affects the cell. This conclusion is confirmed by the same order of magnitude time of information exchange between individual individuals of the population in the calculation and in the experiment. An extremely low concentration of protozoa in the experiment was established, equal to 1000 pcs./liter, at which the indicated effect is observed.An unambiguous dependence of the biological effect in the “water – amoeba population” system on the average power of electromagnetic radiation of cell phones, both in standby mode and in talk mode, has been established. It is concluded that the presented method of changing the physical properties of the aquatic environment of a population of protozoa under the influence of electromagnetic fields can be a model experiment in identifying the mechanisms of interaction of biological systems with electromagnetic radiation, determining the response time of biological systems to external electromagnetic influence, and establishing the degree of influence of radiation in the 4G, 5G ranges.

The motivation for investigating the issues presented in this article stemmed from a need to understand better the relationship in long-established physics formulas and extract the information they provided using conventional methods. Based on the definition of magnetic flux quantization, which is based on a combination of fundamental physical constants, the Planck constant, and the particle’s elementary charge, this work explores the results that arise when this equation is combined with the equation of the Bohr-level electrostatic force acting on the electron, which leads to a new mathematical relationship between the combined expressions. The new relationship yields novel theoretical findings related to the known universal constants. Following this insight, the formalism developed in this paper indicates that the mass of the electron and other subatomic particles is associated with the magnitude of the square of the magnetic flux quantum, which makes up the particle. This conclusion is not as strange as it may seem, as the square of the magnetic flux quantum appears in the context of magnetic energy in a current loop and, according to Einstein’s special theory of relativity, energy is equivalent to mass. Another aspect described at the end of this paper demonstrates the connection between the square of the magnetic flux quantum through the Bohr radius and the significance of the wave function in the atom. The theoretical results are in full accordance with experimental results published by NIST CODATA 2018 that I’ve used, which validates the existence of the relationship.

Spiritual security should be a priority in our modern globalized society. Therefore, the study provides convincing evidence that it is important to develop a theoretical understanding of spiritual security. Several theoretical concerns regarding the establishment and maintenance of spiritual security are addressed in the article. He explores many ideas that are interrelated, including spiritual security, worldview, and spirituality. To ensure spiritual security, a practical analysis is carried out of the need to carry out various measures that strengthen the spiritual health of society.The article explains the methodology used in spiritual Security Investigations. According to the author, different levels of spiritual security can be analyzed using a structural-logical model and a dialectical method of cognition. Comparative analysis is also seen as a valuable tool. Spiritual intelligence is essential to overcome barriers, manage change, and ensure personal security and its impact on relationships. The process begins with introspection and evaluation, concluding with the ability to assess and understand the environment. By analyzing and understanding natural phenomena, it is possible to develop a sense of reality and a deeper appreciation of the nature of human existence. A person can feel spiritually safe if he adheres to his moral and spiritual beliefs and complies with the norms of society. It contains such things as worldview, social behavior, culture, research and social development. By expanding the spiritual point of view, the danger to the spiritual security of a person can be reduced.

Background: Atopic dermatitis (AD), a common dermatological condition, is often associated with significant economic and social burdens. Despite extensive studies globally, there is a gap in understanding the comprehensive impact of this condition in Romania. Objectives:This study evaluated the economic burden and quality of life impact of AD in Romania, considering both direct and indirect costs. Materials & Methods: A mixed methods cost of illness study was conducted from April to October 2023. A patient survey, expert reviews, and national health data analysis were used to assess direct medical costs (treatments, medical services), direct non-medical costs (transportation, accommodation), and indirect costs (productivity losses). Quality of life was evaluated using the EuroQol EQ-5D-5L instrument. Results: In 2022, the total cost of atopic dermatitis in Romania was 32.983.498 EUR for adults and 31.573.968 EUR for children. Adult costs included 24.534.603 EUR in direct and 8.429.884 EUR in indirect medical costs, with an average annual cost per patient of 447 EUR. Pediatric costs involved 15.026.781 EUR in direct and 16.516.410 EUR in indirect costs, averaging 290 EUR per patient annually. Conclusion: Care expenditure with AD management in Romania is substantially lower than in other countries, posing a significant economic burden, primarily driven by indirect costs. This study provides a foundation for future policy interventions and highlights the need for targeted management strategies for AD.

The aim of the research presented here is to assess the impact of depressive disorders on the potential of the labour markets in the countries of the European Union, with particular reference to the disparities between the 'old' and 'new' EU countries. The initial hypothesis of persistent inequalities in the system under study was verified by analysing the process of convergence in the burden of depressive disorders among people aged 20-54 that occurred in the EU-27 group of countries between 1990 and 2019. The study used data from the Global Burden of Disease Study 2019 (IHME, 2020), which examined the number of years lived with disability (YLD) due to depression in the working age population. The analysis showed that the high burden of the consequences of depressive disorders is particularly true for the highly developed economies of the EU-14. The results of the convergence assessment did not confirm the real effect of catching up over time with economies in a more favourable situation, and the inequalities observed at the beginning of the analysis period deepened..

This article is the fourth part of a scientific project under the general title “Geometrized vacuum physics based on the Algebra of Signatures". In the first three articles [1,2,3], the foundations of the Algebra of Stignatures were laid and the main aspects of the kinematics of vacuum layers were considered. This article continues the development of the mathematical apparatus of the proposed project, in particular, the dynamics of vacuum layers is developed based on the Algebra of Signatures. The development of this direction of research (with simplifications related to Riemann's differential geometry) led to the possibility of a geometrized representation of the electric field strength and magnetic field induction. This geometrized mathematical apparatus allows one to interpret the electromagnetic field as an interweaving of accelerated and rotational flows of the adjacent layers of vacuum. The proposed dynamic models of accelerated movements and rotations of vacuum layers can provide a theoretical basis for the development of “zero” (i.e. vacuum) technologies.

Derivatives products have become essential in portfolio diversification, price discovery and risk hedging. Derivatives are complex instruments; their role is twofold, risk management and speculation, and their actual Impact on the underlying assets’ behaviours are not well understood. Little is documented empirically on how these instruments’ two-edged roles influence firms’ financing decisions, firm risk exposures, and stability. Given the growing interest in using derivatives in risk management and portfolio engineering, this study examines the practical impact of derivatives usage on the underlying firm’s financing policy and stability. The paper uses data from South African listed non-financial firms for the period 2000 to 2019. The study employs a dynamic panel model estimated with System Generalised Methods of Moments (GMM). The initial analysis shows that derivatives use reduces the cost of capital and increases firm stability. However, further in-depth analysis provides evidence that extensive use of derivatives increases firms’ capital costs and negatively impacts financial stability. These findings imply that the risk embedded in derivatives’ speculation dominates their risk management function. The results are subjected to numerous controls for robustness, including financial leverage, firm size, cashflows and asset tangibility.

Antibiotics are the most magnificent discovery of 20th century that have saved millions of lives from infectious diseases. Microbes have developed acquired antimicrobial resistance (AMR) to many drugs due to high selection pressure from increasing use and misuse of antibiotics over the years. The transmission and acquisition of AMR occur primarily via human–human interface both within and outside of the healthcare facilities. A huge number of interdependent factors related to healthcare and agriculture govern the development of AMR through various drug resistance mechanisms. The emergence and spread of AMR from the unrestricted use of antimicrobials in livestock feed has been a major contributing factor. The prevalence of AMR bacteria has attained its incongruous level worldwide and threatening global public health as silent pandemic, necessitating urgent intervention. Therapeutic options of AMR bacterial infections are limited resulting in significant morbidity and mortality with high financial impact. The paucity in discovery and supply of new novel antimicrobials to treat life-threatening AMR infections stands in sharp contrast to demand. Immediate interventions to contain AMR include surveillance and monitoring, minimizing over the counter antibiotics and antibiotics in food animals, access to quality and affordable medicines, vaccines and diagnostics, and enforcement of legislation. An orchestral collaborative action within and between multiple national and international organizations are required urgently, otherwise, a post-antibiotic era can be a real possibility than an apocalyptic fantasy for the 21st century. This narrative review highlights on the basis, mechanisms and factors in microbial resistance and key strategies to combat antimicrobial resistance.

The energy potential of long-period oscillations is estimated by comparing it with watercourse power. The relaxation time of long-period waves is chosen for the estimation time interval, during which their amplitude decreases e (Euler's number) times from the initial one. According to calculations, the amount of energy produced during this time by the watercourse is 9.35–18.71 million kW×h, while the amount of energy of long-period oscillations is 3–6 times less – 1.60–5.48 million kW×h. The components of the economic factor of using long-period waves and currents for electricity production are the predictability of their magnitudes and location of maxima, long-term availability, concentration.

According to the Water Framework Directive, the Ecological Flow (Eflow) is assumed to be the minimum water discharge required to achieve and maintain the environmental objectives of “good quality status” in a natural water body. It is highly recognized that, the hydrological regime of natural flow plays a primary and crucial role influencing the physical conditions of habitats, which in turn determines the biotic composition and sustainability of aquatic ecosystems. Furthermore, the simple assumption to supply a minimum instream during dry periods is not enough any longer in order to protect the river environment. The recent hydro-ecological understanding states that all flow components might be considered as operational targets for water management, starting from base flows (including low flows) to high and flood regimes in terms of magnitude, frequency, duration, timing and rate of change. Several codes have been developed and applied on different case studies in order to define common tools to be implemented for the Eflow assessment. The study proposes the application of the Indicators of Hydrologic Alteration methodology (IHA by TNC) coupled to the valuation of the Index of Hydrological Regime Alteration (IARI by ISPRA) as an operative tool to define the ecological flow in each monitoring cross section to support the sustainable water resources management and planning. The case study of Agri River, in Basilicata (Southern Italy) is presented. The analyses have been carried out on monthly discharge data derived applying the HEC-Hydrological Modelling System at the basin scale using the daily rain data measurements obtained by the regional rainfall gauge stations and calibrated through the observed inlet water discharge registered at the Lago del Pertusillo reservoir station.

Starting with unitary quantum dynamics, we investigate how to add quantum measurements. Quantum measurements have four essential components: the furcation, the witness production, an alignment projection, and the actual choice decision. The first two components still lie in the domain of unitary quantum dynamics. The decoherence concept explains the third contribution. It can be based on the requirement that witnesses reaching the end of time on the wave function side and the conjugate one have to be identical. In this way, it also stays within the quantum dynamics domain. The surjection hypothesis explains the actual choice decision. It is based on a two boundary interpretation applied to the complete quantum universe. It offers a simple way to reduce these seemingly random projections to purely deterministic unitary quantum dynamics, eliminating the measurement problem.

The calculation of the vapour pressure of organic molecules at 298.15K is presented using a commonly applicable computer algorithm based on the group-additivity method. The basic principle of this method rests on the complete breakdown of the molecules into their constituting atoms, further characterized by their immediate neighbour atoms. The group contributions are calculated by means of a fast Gauss-Seidel fitting algorithm using the experimental data of 2036 molecules from literature. A ten-fold cross-validation procedure has been carried out to test the applicability of this method, which confirmed excellent quality for the prediction of the vapour pressure, expressed in log(pa), with a cross-validated correlation coefficient Q2 of 0.9938 and a standard deviation  of 0.26. Based on these data, the molecules' standard Gibbs free energy G°vap has been calculated. Furthermore, using their enthalpies of vaporization, predicted by an analogous group-additivity approach published earlier, the standard entropy of vaporization S°vap has been determined and compared with experimental data of 1129 molecules, exhibiting excellent conformance with a correlation coefficient R2 of 0.9598, a standard error  of 8.14 J/mol/K and a medium absolute deviation of 4.68%.

Remdesivir (RDV) has garnered much hope for its moderate anti-COVID-19 effects, but its limited amelioration of survival in hospitalized patient causes a huge controversy over the applicability of RDV to COVID-19 treatment. Developing strategies to improve its antivirus efficacy is urgently required. As anticipated, RDV exhibits similar behavior with other nucleotide analogs to disrupt the metabolism of natural endogenous ribonucleotides (RNs) and deoxyribonucleotides (dRNs). Alterations in endogenous RNs and dRNs play a critical role in virus replication as well as other key cellular functions. Thus elucidation of the disturbances of RDV on RNs and dRNs could help to understand its exact mechanism of action. Here, the metabolic profiling determined by liquid chromatography–mass spectrometry method showed a general increase in the abundance of nucleotides and a more than 2-fold increase for specific nucleotides. However, the variation of pyrimidine ribonucleotides was relative slight or even contrary, resulting in obvious imbalance between purine and pyrimidine ribonucleotides, which implied the obstacle of RDV to pyrimidine synthesis and could further block the transcription and replication of viral RNA. Additionally, the extreme disequilibrium between cytidine triphosphate (CTP) and cytidine monophosphate might result from the inhibition of CTP synthase and provide a metabolic target for the treatment of COVID-19 infection. Since nucleotides metabolism pathways are vulnerable to nucleotide analogues and are liable to be the regulation targets, it is promising to enhance the efficacy of RDV through co-administration with CTP synthase inhibitors or de novo pyrimidine synthesis inhibitors to exacerbate the imbalance of nucleotide pools.

This paper, the second in a series of two, describes the experimental results for removing arsenic from the dust collected in the electrostatic precipitators of a fluidized bed roasting oven (RP dust). The RP dust produced is discharged as a toxic waste, although its copper content is close to 20% by weight. This work aims to process the RP dust; until obtained a material with a low concentration of arsenic, which could be recirculated in smelting operations and recover the valuable metals. Based on the successful experience obtained in the first document with FS dust, this work proposes to use the reduction-sulphidation-volatilization processes to carry out the volatilization of arsenic from RP dust. A set of experiments was realized in the roasting different ratios of the mixture of copper concentrate / RP dust, sulfur / RP dust varying temperature and roasting time; to reach an arsenic concentration <0.5% by weight. The RP dust was characterized using different techniques, that confirmed more than 20% by weight of copper and describing its structure as a small particle agglomerate (<5 µm), with a complex sulfoxide morphology. The main results indicated: that for a 75/25 mixture of the copper concentrate / PR dust under 700 ° C, 15 minutes roasting time with air atmosphere, the arsenic volatilization was 96% by weight. Meanwhile, for a 5/95 mixture of sulfur / RP dust, at 650 ° C, the volatilization of arsenic was 67% by weight.

This paper (the first of a series of two) seeks to describe the experimental results of removing arsenic from dust collected in electrostatic precipitators of copper into the pyro-metallurgy gas cleaning systems. The first work corresponds to the treatment of dust contained in gas off generated in the copper Flash Smelting Furnace process (FS dust), while the second focuses on the treatment of dust generated from a Fluidized Bed Roasting Furnace (RP dust). The dust is complex sulphur-oxide-metals with concentrations of copper above 10 wt % and relatively high concentrations of silver. Due to the dust has an arsenic’s concentration above 5 wt %, makes it difficult to recover valuable metals through hydro-metallurgical processes or by direct recirculation of the dust into a smelting furnace. Thus, the development of pyrometallurgical processes aimed to reduce the concentration of arsenic in dust is the main purpose of this study, particularly the production of a material suitable for recirculation in smelting operations. The works conducted provide a detailed characterization of the dust, including Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN), Scanning electron microscope-Energy Dispersive X-ray analysis (SEM/EDS), X-ray diffraction (XR-D), elemental chemical analysis using Atomic Adsorption (A. A.) and X-Ray Fluorescence (X-RF). By considering that arsenic volatilization requires a process of reduction-sulphidation-volatilization, the works explore the roasting of mixtures of copper concentrate/dust, sulphur/dust and pyrrhotite/dust. The degree of volatilization was determined by elemental chemical analysis of arsenic in the mixture after and before the roasting process. The results indicated the effect of parameters such as temperature, gas flow, gas composition and the ratio of mixtures (concentrate, sulphur or pyrrhotite)/dust on the volatilization of arsenic. The findings indicate that the concentration of arsenic in the FS dust can be reduced to a relatively low level (<0.5 wt %), allowing to the material to be recirculated into smelting processes.

We report here a giant microfossil resembling the conidium of an ascomycete fungus (cf. Alternaria alternata). The specimen is preserved in stromatolitic black chert of the Gunflint Iron Formation (Paleoproterozoic Eon, Orosirian Period, ca. 1.9-2.0 Ga) of southern Ontario, Canada, and the rock that provided the thin section may have been collected by Elso Barghoorn as part of the original discovery of the Gunflint microbiota. The large size of the fossil sets it apart from other, tiny by comparison, Gunflint microfossils. The fossil is 200 microns in length and has cross walls. Individual cells are 30-46 microns in greatest dimension. The apical ‘spore’ is cap-shaped, and has partly separated from the rest of the structure. Cloulicaria gunflintensis gen. nov. sp. nov. may provide early evidence for eukaryotes (fungi) in the fossil record, and may also represent the earliest evidence for asexual reproduction in a eukaryote by means of mitospores.

Current instrumental technology in evaluating performance of skin care creams is still rather limited and there are no industrial standard testing equipment, method and performance specifications for it. In this paper, we report our attempt in using an instrument called PhabrOmeter for this purpose. PhabrOmeter is a commercialized instrument for sensory performance evaluation of textiles, leather, paper and nonwoven and has been designated by American Association of Textile Chemists and Colorists (AATCC) as a standard test method for textiles, AATCC TM 202 in 2013. By adopting artificial skin samples treated with skin care creams, we have developed a procedure to apply this instrument for evaluation of skin care creams from sample preparation, measurement to data analysis and interpretation. The results using commercial skin care creams to demonstrate the feasibility and advantages of this instrument are provided.

This paper is concerned with representing sums of finite products of Chebyshev polynomials of the second kind and of Fibonacci polynomials in terms of several classical orthogonal polynomials. Indeed, by explicit computations each of them is expressed as linear combinations of Hermite, generalized Laguerre, Legendre, Gegenbauer and Jacobi polynomials which involve the hypergeometric functions ${}_1 F_1$ and ${}_2 F_1$.

SerIoT is a Research and Innovation Project funded by the European Commission to demonstrate secure networks for the Internet of Things (IoT). This paper presents an overview of the design for smart and secure network infrastructures for the IoT, based on Software Defined Networks (SDN), named the SerCPN system, whose main component is a smart SDN-Controller with online cognitive security surveillance and reporting, which establishes and dynamically modifies paths that enhance security for IoT devices and end users, and offers a high quality of service (QoS) with required security constraints. This online cognitive surveillance and path management is based on the Cognitive Packet Network (CPN) principle and uses Random Neural Networks (RNN) for decision making.

Traffic anomaly detection is crucial for urban management, yet current research is often confined to small-scale endeavors. This study collected nine months of real-time Wuhan traffic monitoring data from Amap. We proposed Traffic-ConvLSTM, a multi-scale spatial-temporal technique based on long and short-term memory networks (LSTM) and convolutional neural networks (CNN) to effectively achieve long-term anomaly detection at the city level. First, we convert the traffic flow data into image representation, which enables the capture of the spatial correlation between traffic flow and roads and the correlation between traffic flow and roads, as well as the surrounding environment. Second, The model utilizes convolution kernels of different sizes to extract spatial features at road-level, regional-level, and city-level scales, while incorporating temporal features of different time steps to capture hourly, daily, and weekly dynamics. Additionally, varying weights are assigned to the convolution kernels and temporal features of varying spatio-temporal scales to capture the heterogeneous strengths of spatio-temporal correlations within patterns of traffic anomalies. The proposed Traffic-ConvLSTM model exhibits improved performance over existing techniques in the task of identifying long-term and large-scale traffic anomaly occurrences. Furthermore, the analysis reveals significant traffic anomalies during holidays and urban sporting events. The diverse travel patterns observed in response to various activities offer insights for large-scale urban traffic anomaly management, providing recommendations for city-level traffic control strategies.

In order to reduce the environmental impact of energy enterprises, it is important to promptly identify cases of possible changes in the quality of wastewater generated at power plants, that is cases of exceeding the maximum permissible concentrations of pollutants in wastewater. The goal of the method for detecting complex anomalies in multidimensional time series obtained from smart energy station’s sensor channels is to increase the accuracy of detecting pollution levels in industrial wastewater. To achieve this goal, the following tasks were solved: methods for detecting time series anomalies were analyzed, the method for detecting complex anomalies was developed, software implementation of the algorithm was carried out and experiments were conducted. The developed method is proposed to be used in an smart energy monitoring system.

Intermittent religious fasting increases a risk of hypo- and hyperglycemia in individuals with diabetes, but its impact in those without diabetes is poorly investigated. The study aim was to examine the effects of religious Bahá'í fasting (BF) on glycemic control and variability and compare these effects with time-restricted eating (TRE). In a three-arm randomized controlled trial, 16 subjects without diabetes were assigned to a BF, 16:8 TRE or control group. Continuous glucose monitoring and food intake documentation was conducted before and during the 19 days of intervention, and 24-hour mean glucose, glycemic variability indices, and glucotypes were assessed. BF and TRE groups, but not the control group, markedly reduced the daily eating window while maintaining macronutrient composition. Only the BF group decreased caloric intake (-677.8 ± 357.6 kcal, p=0.013), body weight (-1.92 ± 0.95 kg, p=0.011) and BMI (-0.65 ± 0.28 kg, p=0.006). Higher maximum glucose values were observed during BF in the within-group (+1.41 ± 1.04, p=0.039) and between-group comparison (BF vs. Control: p= 0.010 and TRE vs. BF: p= 0.022). However, there were no alterations of 24-hour mean glucose, intra- and inter-day glycemic variability indices, or glucotypes in any group. Proportions of time above and below range (70-180mg/dl) and HbA1c values remained unchanged. BF and TRE do not exhibit negative effects on glycemic control and variability in subjects without diabetes.

The extent of correlation or co-movement among the returns of developed and/or emerging stock markets remains pivotal for efficiently diversifying global portfolios. This correlation is prone to variation over time as a consequence of escalating economic interdependence fostered by international trade and financial markets. In this study, we analyzed the time-varying correlation and co-movement between the JSE.JO stock market of South Africa and its developed and developing stock market partners. The Dynamic Conditional Correlation - Exponential Generalized Autoregressive Conditional Heteroscedasticity (DCC-EGARCH) methodology is employed with different multivariate distributions to explore the time-varying correlation and volatilities between the JSE.JO stock market and its partners. Based on the conditional correlation results, the JSE.JO stock market is integrated and co-moves with its partners, and the conditional correlation for all markets exhibit time-variant behavior. The conditional volatility results show that the JSE.JO stock market behaves differently from other markets, especially after 2015, indicating a positive sign for investors to diversify between JSE.JO and its partners. The highest value of conditional volatility for markets was in 2020 during the COVID-19 pandemic, representing the riskiest period that investors should avoid due to the lack of diversification opportunities during crises.

The installation of electric vehicle supply equipment (EVSE) increases demand and peak loads, potentially straining existing energy distribution infrastructure. Dispersed and inadequately planned placement of charging points (CPs) can disrupt the electrical grid, surpass contracted demand thresholds, and require infrastructure upgrades, thereby incurring unfeasible costs for Distribution System Operators (DSOs). In this context, it is necessary to recognize the role of business models in enabling effective electrification of the transportation sector. In response to these challenges, this paper introduces a novel e-mobility hub management strategy, tailored for implementation in the Brazilian context. The proposed strategy revolves around a microgrid configuration encompassing dispatchable and photovoltaic generation, a battery energy storage system (BESS), EVSE infrastructure, and local loads. Moreover, this centralized controller facilitates the implementation of dynamic pricing and demand-response mechanisms, integral to business models seeking to integrate EVSE into the distribution grid. To validate the efficacy of the proposed solution, hardware-in-the-loop (HIL) simulations of the microgrid system are conducted. These simulations, incorporating the centralized controller, serve as a tool for assessing system performance and viability before on-site equipment deployment. Finally, this paper concludes with the insights gleaned from test analysis and its discussion through a selection of the most expressive scenarios, including islanded and connected operation modes.

This study investigates the impact of real-time emotional feedback on the quality of teamwork conducted over videoconferencing. We developed a framework that provides real-time feedback through a virtual mirror based on facial and voice emotion recognition. In an experiment with 28 teams (84 participants), teams collaborated over Zoom to set up a virtual Mars station using custom simulation software. Participants were divided into 14 experimental teams which were shown the virtual mirror, and 14 control teams without it. Team performance was measured by the improvement in the Mars simulation output quality. Our analysis using correlation, multilevel regression, and machine learning revealed that fewer interruptions but an increasing number over time correlated with higher performance. Higher vocal arousal and happiness also enhanced performance. We confirmed that female presence in teams boosts performance. SHAP values indicated that high variability in happiness, head movement, and positive facial valence—an “emotional rollercoaster”—positively predicted team performance. The experimental group outperformed the control group, suggesting that virtual mirroring improves virtual teamwork and that interrupting each other more, while speaking less, leads to better results.

The open data market is growing, driven by laws requiring governments to make data publicly available. However, the true value of this market lies in the products and services derived from open data. In Slovenia, the open data market has been growing since 2015, especially in the field of mobility. Platforms such as Avtolog.si facilitate the retrieval of vehicle data via vehicle identification numbers, while tocen.si, ojpp.si, and brezavta.si aggregate mobility data, focusing on sustainable and micromobile public transportation services. These platforms use open government data and private sector open data, and are freely accessible. This study examines the use of open data in the Slovenian mobility applications and similar solutions developed in other countries. By mapping these applications, we gain valuable insights into potential advances in the field, and provide a useful resource for future developers worldwide. By focusing on the socio-economic impact of these innovations, the study identifies methods for evaluating such applications. This approach highlights how transforming open data into user-friendly products and services can deepen our understanding of their broader societal and economic benefits. While open data is valuable in its own right, its full transformative potential is realized through innovative products that support sustainable lifestyles and promote environmentally conscious behavior.