There are many pollution and environment problem in the human ecosystem. There are different methods are used to removal of sulfur from sour gases for example Basic Claus process and Modified Claus process . There are different chemical software are used for simulation and optimization of Claus process for example Aspen Plus and Chemcad ECT. The Gibbs free energy method is introduced and model of Claus process. There are new parameter are introduced in reaction furnace to reduce the error from 33% to 7 %. The waste heat boiler is installed at the reaction furnace in which high pressure stream is produced and study the decomposition the hydrogen sulphide. The new rate of reaction is introduced of the enhancement of H2 production in chemical process. The simulation of reaction furnace in Aspen plus software is the maximum utilization of process. Due to suitable operating condition of reaction furnace is caused the maximum destruction of ammonia gas in the reactor. When we are increasing the oxygen concentration and temperature of feed is causing decreasing the ammonia production in reaction furnace. It is below than acceptance value of ammonia is 150 ppm in the reaction furnace. The presence of oxygen components, Sulfur oxide, hydroxide components are effect on decreasing the amount of ammonia in furnace and temperature is about at 1350⁰C. It is noted that when the production of sulfur recovery is decrease in Claus process and the production of carbon monoxide is increase in the thermal section at the existence. Now we are work on parametric studies of furnace that could be causes the production of ammonia destruction and CO emission in the Claus process. Due to optimize the reaction furnace parameter are help to get large of sulfur production, ammonia gas destruction, increased the catalyst life and decreased of dangerous gases.

The concept of using special electrical circuit design realize a "cold resistors", that is, an active resistor circuitry with lowered effective noise temperature, was first introduced about 80 years ago. Later on, various kinds of artificial resistors were applied in different research areas, such as gravitational wave detection, photo-amplifiers and quartz oscillators. Their proofs of concepts were experimentally proved. Unfortunately, the complete theory was not found even though several attempts had been published, sometimes with errors. In this paper, we describe a correct and complete circuit theoretical model of a cold resistor system. The results are confirmed by computer simulations. A design tools for this circuit is also shown.

SARS-CoV-2 causes severe pneumonia epidemics and probably originated in horseshoe bats, but the intermediate host is unknown. The interaction of SARS-CoV-2 spike protein and its acceptor protein ACE2 is an important issue in determining viral host range and cross-species infection, while the binding capacity of Spike protein to ACE2 of different species is unknown. Here, we used the atomic structure model of SARS-CoV-2 and human ACE2 to assess the receptor utilization capacity of ACE2s from different species including cats, chimpanzees, dogs, cattles. Our results show, domestic cats (Felis catusc) and dogs (Canis lupus familiaris) are more susceptible to infection by SARS-CoV-2 and that they can efficiently transmit the virus to previously uninfected animals that are housed with them. Especially, cats could be a choice of animal model for screening antiviral drugs or vaccine candidates against SARS-CoV-2.

Complete digraphs are referred to in the combinatorics literature as tournaments. We consider a family of semi-simplicial complexes, that we refer to as ``tournaplexes'', whose simplices are tournaments. In particular, given a digraph G, we associate with it a ``flag tournaplex'' which is a tournaplex containing the directed flag complex of G, but also the geometric realisation of cliques that are not directed. We define several types of filtrations on tournaplexes, and exploiting persistent homology, we observe that flag tournaplexes provide finer means of distinguishing graph dynamics than the directed flag complex. We then demonstrate the power of these ideas by applying them to graph data arising from the Blue Brain Project's digital reconstruction of a rat's neocortex.

The informational re-interpretation of the basic laws of the mechanics exploiting the Landauer principle is suggested. When a physical body is in rest or it moves rectilinearly with the constant speed, zero information is transferred; thus, the informational affinity of the rest state and the rectilinear motion with a constant speed is established. The analysis of the minimal Szilard thermal engine as seen from the non-inertial frame of references is carried out. The Szilard single-particle minimal thermal engine undergoes the isobaric expansion relatively to the accelerated frame of references, enabling the erasure of 1 bit of information. The energy ΔQ spent by the inertial force for the erasure of 1 bit of information is estimated as: ΔQ≅5/3 k_B T ̅, which is larger than the Landauer bound but qualitatively close to it. The informational interpretation of the equivalence principle is proposed: the informational content of the inertial and gravitational masses is the same.

This review describes major advances in the use of functionalized molecular metal oxides (polyoxometalates, POMs) as water oxidation catalysts under electrochemical conditions. The fundamentals of POM-based water oxidation are described together with a brief overview of general approaches to designing POM water oxidation catalysts. Next, the use of POMs for homogeneous, solution-phase water oxidation is described together with a summary of theoretical studies shedding light on the POM-WOC mechanism. This is followed by a discussion of heterogenization of POMs on electrically conductive substrates for technologically more relevant application studies. Stability of POM water oxidation catalysts are discussed on selected examples where detailed data is already available. The review finishes with an outlook on future perspective and emerging themes in electrocatalytic polyoxometalate-based water oxidation research.

Nodes in wireless sensor networks (WSN) are characterized particularly by their limited power and memory capabilities. Limited memory is an important parameter as it defines the size of the operating system and the processing code. As established previously, energy and memory efficiency is the most important evaluation factors of WSNs as they are directly related to data loss and network lifetime. However, based on our simulation results, memory efficiency determines the selection or abandon of nodes by the botmaster for the propagation of bots in an IoT infrastructure. Consequently, the node’s memory efficiency determined the spread of bots in the network and provides defense actors with an insight of the botmaster behavior for mitigation of the attack. Conventional botnet propagation and mitigation models did not consider the impact of node’s memory efficiency in the IoT platform. To address this gap, we build IoT-SIEF, a novel propagation model with forensic capability that will analyze command and control propagation behavior based on the perspective of the node’s memory efficiency. IoT-SIEF model used to explore the dynamics of propagation using numerical simulation with more than 50% outperform other models in mitigating the number of secondary bots. Consequently, it can serve as a basis for assisting the planning, design, and defense of such networks from the investigator's point of view.

Key features of glycogen metabolism in excitable tissues are not well-explained by current concepts. Glycogen stores in brain and skeletal muscle are generally considered to function as local glucose reserves, to be utilized during transient mismatches between glucose supply and demand; however, quantitative measures show that blood glucose supply is likely never rate-limiting for energy metabolism in either brain or muscle under physiological conditions. These tissues nevertheless do normally utilize glycogen during intervals of increased energy demand, despite the availability of free glucose, and despite the ATP cost of cycling glucose through glycogen polymer. This seemingly wasteful shunt can be explained by considering the effect of glycogenolysis on the amount of energy derived from ATP (ΔG’ATP). ΔG’ATP is diminished by elevations in Pi, such as occur at sites of rapid ATP hydrolysis and net phosphocreatine consumption. Glycogen utilization counters this effect by sequestering Pi in glycolytic metabolites (glycogen_n + Pi → glycogen_n-1 + glucose-1-phosphate → phosphorylated glycolytic intermediates), and thereby maintains the amount of energy obtained from ATP at sites of rapid ATP consumption. This thermodynamic effect may be particularly important in the narrow, spatially constricted astrocyte processes that ensheath neuronal synapses. This effect can also explain the co-localization of glycogen and cytosolic phosphocreatine in brain astrocytes, glycolytic super-compensation in brain when glycogen is not available, and aspects of exercise physiology in muscle glycogen phosphorylase deficiency (McArdle’s disease).

To understand the mystery of final unification, in our earlier publications, we proposed two bold concepts: 1) There exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions. 2) There exists a strong elementary charge in such a way that its squared ratio with normal elementary charge is close to reciprocal of the strong coupling constant. In this paper we propose that, can be considered as a compound physical constant associated with proton mass, electron mass and the three atomic gravitational constants. With these ideas, an attempt is made to understand nuclear stability and binding energy. In this new approach, nuclear binding energy can be fitted with four simple terms having one unique energy coefficient with a formula, where is an estimated mean stable mass number. With this new approach, Newtonian gravitational constant can be estimated in a verifiable approach with a model relation of the form, where is the Fine structure constant. Estimated and is 62 ppm higher than the CODATA recommended It needs further investigation. Proceeding further, an attempt is made to fit the recommended quark masses.

The slate aggregate has long been perceived as a substandard, low quality waste material with its physical and chemical properties not being competitive with those of the primary aggregates. It is assumed that the slate aggregate particles are not strong, that is not durable and will not compact. This research aims to address those claims and review the available literature on the performance of the slate aggregate. The review inaugurates by analysing the physical, chemical and mechanical properties of slate, before expanding into a literature review of laboratory testing’s on the effect of moisture content on density, compaction and layer thickness of slate aggregate.The paper reviews case studies of construction projects in North Wales, where the slate aggregate has been used for general fill and road building for many years. Some of the case studies include the A55 coastal road and duelling of the A5 in Anglesey (WRAP, 2004), where slate aggregate was successfully used as sub-base. The paper also investigates why many civil engineers are reluctant to use the slate aggregate and regard the material as sub-standard, flaky aggregate. The research paper reviews the potential usages and various products the slate aggregate is suitable for and satisfies the requested standards. The final topic reviewed is the cost of transporting slate aggregate compared with the cost of transport for primary aggregate and the introduction of the Primary Aggregates Tax (Parliament of the United Kingdom, 2011). The last topic includes a critical analyses of the claims that the slate aggregate a commercially viable construction material despite its remote location (Woodward et al, 2004). The transportation cost and the supply chain complexities must be evaluated prior to considering the long-term sustainability of the product (Radanliev et al^1-6, 2014, 2015, 2016).

With the existence of several programming languages such as C/C++, Java, C#, LISP, Prolog, Python, Simula, F#, Go, Haskell, Scala, Ruby, Dart, Swift, Groovy etc. and diverse paradigms like structured, object-oriented, list, aspect-oriented, service-oriented, web, mobile and logic programming, there is a need to perform an exhaustive comparative analysis of diverse compilers and environments before making a choice of implementation technology in software engineering. Optimization of compilers helps to reduce execution time by making use of high speed processor registers, thereby, eliminating redundant computation. This paper reports some series of performance analysis done with some popular programming languages including Java, C++, Python and PHP. Programs involving recursive and iterative functions like factorial of large numbers and binary search of large arrays were run on the various platforms with the execution time recorded in milliseconds and represented in a chart. This can aid in making a selection of the appropriate language to use for a given application domain.

In this paper, we define Tetranacci and Tetranacci-Lucas matrix sequences and investigate their properties.

The sunscreen industry is achieving remarkable worldwide prominence by responding to the growing need for skin protection with fast-paced innovation. Increased consumer awareness of the harmful effects of sunlight has fueled the demand for improved photo protection. The need for broad-spectrum protection from both UVA and UVB rays has inspired scientists worldwide to research new cosmetic formulations and delivery systems. More effective sunscreen actives, emollients and novel cosmetic and functional ingredients have been regularly added to the formulator’s repertoire. Creativity in innovation has been hindered only by regulatory agencies and patent restrictions worldwide. Familiarity with the current restrictive regulations and patent law infringements has become integral to any research effort attempting to provide improved protection to individuals affected by the sun’s damaging effects. The increasing incidence of skin cancers and photo damaging effects caused by ultraviolet radiation has increased the use of sun screening agents, which have shown beneficial effects in reducing the symptoms and reoccurrence of these problems. Unlike the situation in Europe where sunscreen ingredients are considered under cosmetics guidelines, the FDA is required to define sunscreens as drugs since they are advertised to prevent sunburn and, more recently, the risk of skin cancer. In the USA, the FDA has been regulating this industry since August 25, 1978, with the publication of the Advance Notice of Proposed Rulemaking. Sunscreens are considered drugs and cosmetics and therefore must be governed by the FDA-OTC monograph. With the variety of sunscreen agents used in cosmetic and UV protection products, Australia, Canada, and the European Union (EU) have also developed regulatory protocols on safe sunscreen product use. Unlike the USA though, Australia has approved 34 active sunscreen ingredients and the EU has approved 28 of these ingredients. Current FDA regulations allow labeling of sunscreen products to a maximum of 30þ, despite the many products currently available with numbers as high as 100. From a cosmetic formulation point of view, increasing the SPF number in a product is governed by simple chemical principles.

Integrated information theory (IIT) proposes a measure of integrated information (Φ) to capture the level of consciousness for a physical system in a given state. Unfortunately, calculating Φ itself is currently only possible for very small model systems, and far from computable for the kinds of systems typically associated with consciousness (brains). Here, we consider several proposed measures and computational approximations, some of which can be applied to larger systems, and test if they correlate well with Φ. While these measures and approximations capture intuitions underlying IIT and some have had success in practical applications, it has not been shown that they actually quantify the type of integrated information specified by the latest version of IIT. In this study, we evaluated these approximations and heuristic measures, based not on practical or clinical considerations, but rather based on how well they estimate the Φ values of model systems. To do this, we simulated networks consisting of 3–6 binary linear threshold nodes randomly connected with excitatory and inhibitory connections. For each system, we then constructed the system’s state transition probability matrix (TPM), as well as its state transition matrix (STM) over time for all possible initial states. From these matrices, we calculated, approximations to Φ, and measures based on state differentiation, state entropy, state uniqueness, and integrated information. All measures were correlated with Φ in a state dependent and state independent manner. Our findings suggest that Φ can be approximated closely in small binary systems by using one or more of the readily available approximations (r > 0.95), but without major reductions in computational demands. Furthermore, Φ correlated strongly with measures of signal complexity (LZ, r_s = 0.722), decoder based integrated information (Φ*, r_s = 0.816), and state differentiation (D1, r_s = 0.827), on the system level (state independent). These measures could allow for efficient estimation of Φ on a group level, or as accurate predictors of low, but not high, Φ systems. While it’s uncertain whether the results extend to larger systems or systems with other dynamics, we stress the importance that measures aimed at being practical alternatives to Φ are at a minimum rigorously tested in an environment where the ground truth can be established.

Picrasma javanica Blume or also known as Picrasma nepalensis or Picrasma philippinensis is a plant belongs to the Simaroubaceae family, which is known for its secondary metabolites namely quassinoids with various pharmacological properties including antitumor, antimalarial and antiviral. The plant traditionally used as medicine for different diseases in Myanmar, Thailand and Indonesia. The purpose of this study is to discern the phytochemical constituents and pharmacological activities of Picrasma javanica. The background, phytochemical constituents and pharmacological benefits of Picrasma javanica were reviewed and supported from previous studies, including in vivo and in vitro studies. The literature used in the review comprises of published books, journals, reviews and articles published from the year of 1969 to 2018, which are available in ScienceDirect, PubMed, Scopus and GoogleScholar. Chemical structures presented in this paper are either drawn with ACD/ChemSketch. Picrasma javanica possesses several phytochemical constituents, including quassinoids, alkaloids and triterpenoids. Compounds of the plant were isolated and studied for their pharmacological activities such as antimalarial, antiproliferative, antiviral, antimicrobial and membrane stabilising activity. Most importantly, these studies showed that the key players for the pharmacological benefits are quassinoids and alkaloids present in the plant.Picrasma javanica indeed has therapeutic potentials which may be beneficial for people. However, further extensive studies must be done on the plant as the detailed information on its pharmacological activities are still lacking.

Signalling is a strongly influenced area trending to be applied in almost every focus of biological sciences. The part of signalling or communication from cellular level to a whole organism including plant as well as animal drags a vast diversity of wealthy structural compounds. There is immense demand for new bioactive compounds for the pharmaceutical, agro and food industries. Plant-associated microbes present an attractive and promising source. The concept of the microbiome and the significance it has to host health, diseases state, and the role of immune have been the hub of research that has led to advances in our understanding of the massive power of the small unseen majority of the microbes (Peterson Andrew H., 2013). Before we say about microbiome—plant relation, it is important to first understand the working concept of the microbiome. Every organism on earth counts on their neighbours to sustain life. Microbiome can be considered a community of microorgasims who can prove to be loveable and hateful. The analysis of microbiome structure and function was protagonise in studies of human hosts and has been extensively documented as essential to genetic and functional capacity attributed to the host, comprehending aspects of metabolism and physiology. Plants are crowded with microbial organisms, counting those that colonize internal tissues, also those that adhere to external surfaces. The wide diversity of microorganisms in the soil rhizosphere is collectively plant–soil-associated microbes cover the plant microbiome. The intricate involvement of microbiome serves to plant health and as a tank of additional genes that plants can access when needed.

Our method for density elimination is generalized to the non-commutative substructural logic GpsUL∗. Then the standard completeness of HpsUL∗follows as a lemma by virtue of previous workbyMetcalfeandMontagna. This result shows that HpsUL∗ is the logic of pseudo-uninorms and their residua and answered the question posed by Prof. Metcalfe, Olivetti, Gabbay and Tsinakis.

Vitrimers are covalent network materials, comparable in structure to classical thermosets. Unlike normal thermosets, they possess a chemical bond swap mechanism that makes their structure dynamic and suitable for activated welding and even autonomous self-healing. The central question in designing such materials is the trade-off between autonomy and material stability: The swap mechanism facilitates the healing but it also facilitates creep, which makes the perfectly stable self-healing solid a hard goal to reach. Here, we address this question for the case of self-healing vitrimers made from star polymers. Using coarse-grained molecular dynamics simulations, we study the adhesion of two vitrimer samples and find that they bond together on timescales that are much shorter than the stress relaxation time. We show that the swap mechanism allows the star polymers to diffuse through the material through coordinated swap events, but the healing process is much faster and does not depend on this mobility.

Neuroscience has overwhelmingly and understandably focused on the synaptic modality of signal transmission. There is evidence, however, that from an evolutionary perspective, non-synaptic transmission (NST) preceded synaptic signaling. Moreover, in modern nervous systems, NST coexists and extensively interacts with synaptic transmission modifying neuronal dynamics. In fact, NST remains widespread in complex animals, especially within the interoceptive system where the dearth of insulating barriers such as myelin sheaths and the blood-brain barrier enhances the communication between neural and non-neural tissues mediated by NST. We suggest that this physiological arrangement makes a fundamental contribution to interoception¾the process of sensing visceral states¾which is an essential underpinning of the capacity to feel and the foundation of affective processing.

The demand for suspensions used in thermal spray processes is expanding from research labs using the lab-prepared suspensions toward actual coating production in different industrial sectors. Industrial applications dictate reduced production time and effort which may in turn justify the development of the market for ready-to-use commercial suspensions. To this end, some of the powder suppliers have already taken steps forward by introducing to the market suspensions of some of the most used materials such as yttria-stabilized zirconia (YSZ), alumina and titania. There is, however, a need to compare the suspension characteristics over time and the resultant coatings when using these suspensions as compared with the freshly prepared home-made suspensions. In this work, such comparison is done using YSZ suspensions of the sub-micron to a few micron powders. In addition, some changes in the suspensions' formula were performed as a tool to vary the coatings’ microstructures in a more predictable way, without variation of spray parameters. The coatings were generated using both radial and axial injection of the suspensions into Oerlikon-Metco 3MB and Mettech Axial III plasma spray torches, respectively. A clear effect of suspension viscosity on the coating microstructure was observed using the 3MB torch with radial injection of suspension (i.e. cross flow atomization). The viscosity role, however, was not dominant when using the Axial III torch with axial feed injection system (i.e. coaxial flow atomization).

An examination of Emmanuel Levinas’ writings on money reveals his distance from—and indebtedness to—a philosophical predecessor, Georg Simmel. Levinas and Simmel share a phenomenological approach to analyses of the proximity of the stranger, the importance of the face, and the interruption of the dyadic relationship by the third. Money is closely linked to the conception of totality because money is the medium that compares heterogeneous values. Levinas goes beyond Simmel in positing an ethical relation to money permitting transcendence.

Plasma being the fourth and most abundant form of matter extensively exists in the universe in the inter-galactic regions. It provides an electrically neutral medium of unbound negative and positive charged particles, which has been produced by subjecting air and various other gaseous mixtures to strengthen the electromagnetic field and by heating compressed air or inert gasses for creating negative and positive charged particles known as ions. Nowadays, many researchers are paying attention to the formation of artificial Plasma and its potential benefits for mankind. The literature is sparsely populated with the applications of Plasma. This paper presents specific methods of generation and applications of Plasma, which benefits humankind in various fields, such as in electrical, mechanical, chemical and medical fields. These applications include hydrogen production from alcohol, copper bonding, semiconductor processing, surface treatment, Plasma polymerization, coating, Plasma display panels, antenna beam forming, nanotechnology, Plasma Torch, Plasma pencils, low-current non-thermal Plasmatron, treatment of prostate cancer, Plasma source ion implantation, cutting by Plasma, Plasma etching, pollution control, neutralization of liquid radioactive waste, etc. Resultantly, worth of Plasma technology in the medical industry is increasing exponentially that is closing the gap between its benefits and cost of equipment used for generating and controlling it.

This paper presents the methods of estimating the mean square error of hydrological forecasts, allowing for assessment of their practical applicability. Depending upon the amount and composition of available hydrometeorological data, an appropriate method for forecast error estimation is chosen. A system of statistical tests for comparison of different forecasting methods for the same hydrologic characteristic with the same lead time is presented. These tests allow for choosing an optimal and most accurate forecasting method. Hydrological forecasting method efficiency estimation is based on comparing the forecast error with climatology or inertial (persistence) forecast error using presented tests.

In the area of health, namely hospitals, we can agree that the intrinsic need to have multidisciplinary teams, highly specialized and indispensable resources leads us to a degree of complexity that requires, daily, the best performance, not running away from the logistics area to the rule. The centralization of resources, namely distribution warehouses, emerges as a challenge and possible solution for health institutions to respond in the best possible way to their main purpose: to put the right material in the right place at the right price in the right time space. As regards the advantages of this type of organization, there are several authors who argues that the need for human resources training, ease of coordination and the use of economies of scale are the main advantage. As far as the disadvantages are concerned, there is no special agreement on them, there are disparate factors from author to author, such as: routine, centralization, objectives or operation costs.

Spirit of science is one of the important components of science education theory. It not only directly affects the level of science education, but also indirectly affects the selection, education and evaluation of scientific researchers, and the development of science and technology in a country or region. Although more than a century ago, the researchers began to discuss the topic of spirit of science. However, to date, the research of the definition, attribute, structural model and its characteristics of the spirit of science has not yet made a breakthrough. Based on the detailed literature review, the related theoretical analysis and the research of the structural model of the spirit of science, this paper puts forward the new definition, the attribute and the establishment of the structural model of the spirit of science, and analyzes the match the situation from new structural model of the spirit of science and the scientific nature published by the American Society for the Advancement of Science. The results of this study are of great significance for raising the level of scientific education and cultivating future scientific researchers, enhancing their motivation and skills in innovation in scientific research and promoting the development of future scientific undertakings.

For a graph G, let P(G, λ) be its chromatic polynomial. Two graphs G and H are said to be chromatically equivalent if P(G,λ) = P(H,λ). A graph is said to be chromatically unique if no other graph shares its chromatic polynomial. In this paper, chromatic polynomial of the necklace graph N_n, for n ≥ 2 has been determined. It is further shown that N₃ is chromatically unique.

1) Background: Traditionally, complex biological products such as vaccines presented unique challenges to implementation of even rudimentary characterization packages; thus, the product was defined almost exclusively by its manufacturing process. The advances in technology and analytical tools allowed the application of more comprehensive characterization packages for products such as adsorbed combination vaccines, which contain several antigens in a single formulation to protect against more than one disease, and may contain adjuvants and excipients. Aluminum phosphate (AlPO4) is a well-established adjuvant for enhancing the uptake of vaccines and to induce robust immunity against pathogens. During manufacturing, adjuvant is mixed with protein antigens which may in turn impact their higher order structure and stability. 2) Methods: To study the structural changes of protein antigens after adsorption several analytical tools including DLS, FTIR, Fluorescence, LD, and SEM were used. 3) Results: the AlPO4 adjuvant suspension consists of small submicron particles that form a continuous porous surface. Secondary structure alpha-helix and beta-sheet content of DT and TT increased after adsorption to AlPO4 adjuvant, whereas no significant changes were noted for other protein antigens. Interactions were noted between AlPO4 adjuvant and DT, TT, and FHA. 4) Conclusions: here we report for the first time the use of SEM for the visualization of adsorbed multivalent vaccine components. A unique signature profile detected for each multivalent vaccine by FTIR can be used as a lean in-process test to verify vaccine product composition and identity prior to filling.

In considering the question of machine as artist, the art object can be analytically separated from its making, and its making can be dualistically conceptualized as process on one hand and experience on the other. One of the reasons we value art is that there was an experience of its making. To better understand what is meant by the experience of art-making, this paper presents results from a qualitative, phenomenological study of a group of artists. These results appear in three groups: feeling, intention and lifeworld. Machines cannot experience art-making, at least not in the same way as humans, and thus they cannot create art but only art-like objects. Even so, in the present century, we should not be asking whether machines can be artists, but rather how machines can help more people experience art-making for themselves.

Over the recent decades people’s (rural and urban) communities are facing numerous social and economic changes and challenges. Some of those challenges have been increasingly addressed through the lenses of technological developments and digitalization. In this paper we have made a review of already existing practices while focusing on the existing implementations of the smart village concept and the importance of digital transformation for rural areas. We give special attention to EU policies which we are using as an already existing framework for understanding our own forthcoming examples. We have shown the parallels between the findings and insights from different regions and made an evaluation of presented practices. Our main argument stems from our own previous experiences and experiences of other research approaches, and is grounded on the argument that rural areas are not uniform, and that smart rural development has to be applied in combination with place-based approach. We present the cases of Slovenian pilot practices and support our argument by proposing the FabVillage concept.

In this review, severe plastic deformation (SPD) is considered as a materials processing technology. The deformation mode is the principal characteristic differentiating SPD from common forming operations. For large plastic strains, deformation mode depends on the distribution of strain rates between continuum slip lines and can be varied from pure shear to simple shear. A scalar, invariant and dimensionless coefficient of deformation mode is introduced as a normalized speed of rigid rotation. On this basis, simple shear provides the optimum mode for structure modification and grain refinement whereas pure shear is "ideal" for forming operations. Special experiments and SPD practice confirm this conclusion. Various techniques of SPD are classified and described in accordance with simple shear realization or approximation. It is shown that correct analyses of the processing mechanics and technological parameters are essential for comparison of SPD techniques and the development of effective industrial technologies.

This paper contains theoretical fundamentals of strut and tie models, used in unreinforced horizontal shear walls. Depending on support conditions and wall loading, we can distinguish models with discrete bars when point load is applied to the wall (type I model) or with continuous bars (type II model) when load is uniformly distributed at the wall boundary. The main part of this paper compares calculated results with the own tests on horizontal shear walls made of solid brick, silicate elements and autoclaved aerated concrete. The tests were performed in Poland. The model required some modifications due to specific load and static diagram.

In The Work of the Dead: A Cultural History of Mortal Remains, Thomas Laqueur argues that the work of the dead is carried out through the living and through those who remember, honour, and mourn the dead. Further, he maintains that the brutal or careless disposal of the corpse “is an attack of extreme violence”. To treat the dead body as if it does not matter or as if it were ordinary organic matter would be to deny its humanity. From Laqueur’s point of view it is inferred that the dead are believed to have rights and dignities that are upheld through rituals, practices, and beliefs of the living. Drawing on dark tourism scholarship and cultural memory theory, this paper examines the display of human bones at Sedlec Ossuary, Czech Republic and the tourist culture that has built up around the site. Primarily, my writing calls into question the commoditization of burial places as a conceivable violation of the human rights of the dead. My research is driven by a number of questions: What is it that draws tourists to burial grounds and how do heritage sites negotiate visitor experiences? What are the ethical boundaries when a final resting place with bodies on display is also marketed as a tourist site? Do the dead have human rights and how are the living responsible for preserving those rights?

This paper provides orthogonal moments (OM) such as, Zernike Moments(ZM), Psuedo Zernike Moments(PZM) and Orthogonal Fourier Mellin Moments(OFMM) for the analysis of melanoma images. The moment invariants may vary with respect to geometric variations. For the analysis of orthogonal moments hundred random melanoma images and hundred non-melanoma images have been taken into consideration from the database of 570 melanoma images and 250 non-melanoma images respectively. Orthoganal moments have been computed by varying the phase angles from 10° to 40° with an equal interval of 10° degree for the orders 2, 4,8,16,32,64,128,256 respectively. For the optimal OMs Particle Swarm Optimization (PSO) technique have been used. These set of extracted optimal OMs have been further applied to classify melanoma images. Support Vector Machine (SVM) has been used for the classification of [1]sensitivity=88.78%.

This study examines whether information about the winners of the Sustainability Reporting Award (SRA) contributes to the usefulness of the information in the financial statements. This study used a sample consisting of 110 winners of SRA (SRA firms) and 110 companies that did not receive SRA (non-SRA firms) from 2008 to 2016. The study found that earnings per share (EPS), book value per share (BVPS), and earnings per share change (EPSC) are value relevant information. Results of comparison between SRA firms and non-SRA fimrs, this study found that EPS positive association with stock price and with returns for SRA firms is higher than that for non-SRA firms. Findings of this study also show that, value relevance of BVPS for non-SRA firms is higher than that for SRA firms. When mesures of Price and BVPS are transformed into natural logarithm, the value relevance of BVPS for SRA firms is higher than that for non-SRA firms. Thus, the results are sensitive to measures of the variables. The findings of this study indicate that information about the winners of SRA contributes to the usefulness of financial statements.

We report the electrical characterization and the field emission properties of CVD-grown MoS₂ bilayers deposited on SiO₂/Si substrate. Current-voltage characteristics are measured in the back-gate transistor configuration, with Ti contacts patterned by electron beam lithography. We confirm the n-type character of as-grown MoS₂ and we report normally-on field effect transistors. Local characterization of field emission is performed inside a scanning electron microscope chamber with piezo-controlled tungsten tips working as the anode and the cathode. We demonstrate that an electric field of ~200 V/μm is able to extract current from the flat part of MoS₂ bilayers, which therefore can be conveniently exploited for field emission applications even in low field-enhancement configurations. We show that a Fowler-Nordheim model, modified to account for electron confinement in 2D materials, fully describes the emission process.

The main objective of this paper is to introduce a further extension of extended (p, q)-beta function by considering two Mittag-Leffler function in the kernel. We investigate various properties of this newly defined beta function such as integral representations, summation formulas and Mellin transform. We define extended beta distribution and its mean, variance and moment generating function with the help of extension of beta function. Also, we establish an extension of extended (p, q)-hypergeometric and (p, q)-confluent hypergeometric functions by using the extension of beta function. Various properties of newly defined extended hypergeometric and confluent hypergeometric functions such as integral representations, Mellin transformations, differentiation formulas, transformation and summation formulas are investigated.

Mitochondria function to generate ATP and also play important roles in cellular homeostasis, signaling, apoptosis, autophagy, and metabolism. The loss of mitochondrial function results in cell death and various types of diseases. Therefore, quality control of mitochondria via intra- and intercellular pathways is crucial. Intracellular quality control consists of biogenesis, fusion and fission, and degradation of mitochondria in the cell, whereas intercellular quality control involves tunneling nanotubes and extracellular vesicles. In this review, we outline the current knowledge on the intra- and intercellular quality control mechanisms of mitochondria.

This paper deals with the analytical modeling and control of rectilinear snake robots. During recent times snake robots have created much interest among researchers. The rectilinear pattern gait is one of the four biological snake locomotion modes. Rectilinear snakes have been widely used in rescue operations especially in rough terrains especially in narrow spaces where human intervention is not easy. Computational analysis of rectilinear motion is done using MATLAB.

Sustainability of current energy policies and known mid-term policies are analised in their multiple facets. First an overview is given about the trend of global energy demand and energy production, analysing the share of energy sources and the geographic distribution of demand, on the basis of statistics and projections published by major agencies. The issue of sustainability of the energy cycle is finally addressed, with specific reference to systems with high share of renewable energy and storage capability, highlighting some promising energy sources and storage approaches.

We have studied the relative positions of the frontier levels determine the main electronic properties and reaction ability, there is important necessity to compare the MO of the purine and рyrimidine bases: adenine (A), guanine (G), cytosine (C), thymine (T) and uracil (U). The donor and acceptor properties are the fundamental characteristic of the conjugated molecules and can be quantitatively estimated by relative positions of the frontier molecular orbitals. The MO’s energies can be estimated experimentally or quantum-chemically. Analysis of the relative position of the frontier levels (calibrated by the energy gap) enables the investigation of the donor/acceptor properties of the RNA/DNA bases more detailed. The index φ0 is proposed for the quantitative quantum-chemical estimation of the donor ability of the conjugated molecules: it points on the shifting of the energy gap relative to the reference electron balanced system. The RNA/DNA bases divided strictly by two groups: predominantly donors (φ0 > 0.5) and predominantly acceptors (φ0 > 0.5). Each representative base of the first group forms the stable base pair the representative base of the second group the difference of indices Δφ0 should be optimal to enables the DNA replication.

In this paper, quasi-static axial compression tests are performed on the nodal Moso bamboos to study the size effect on energy absorption of the bamboos and the damage pattern of the multiple bamboo columns. Experimental results show that under the same moisture content, growth age and growing environment, the specific energy absorption (SEA) of the test samples increases with the increase of the out-diameter and thickness of the bamboo columns, indicating that size effect exists for energy absorption of the Moso Bamboos. For the multiple bamboo columns, there are mainly three failure modes for the constituent single bamboo columns: splitting above the node, splitting below the node and splitting through the node. Also, the tensile tests are conducted on three kinds of dog-bone shaped bamboo samples to investigate the macroscopic tensile fracture mode in the longitudinal direction of Moso bamboos. Results show that there is no direct relationship between the fracture pattern and moisture content of the bamboos, as well as the growth age of the bamboos. However, the tensile loading rate and the shape of the dog-bone shaped bamboo sample could affect the macroscopic fracture pattern of the bamboos in some cases.

In this paper, we relate Poisson’s summation formula to Heisenberg’s uncertainty principle. They both express Fourier dualities within the space of tempered distributions and these dualities are furthermore the inverses of one another. While Poisson’s summation formula expresses a duality between discretization and periodization, Heisenberg’s uncertainty principle expresses a duality between regularization and localization. We define regularization and localization on generalized functions and show that the Fourier transform of regular functions are local functions and, vice versa, the Fourier transform of local functions are regular functions.

The number of citations that a paper has received is the most commonly used indicator to measure the quality of research. Researchers, journals, and universities want to receive more citations for their scholarly publications to increase their h-index, impact factor, and ranking respectively. In this paper, we tried to analyses the effect of the number of available Google Scholar versions of a paper on citations count. We analyzed 10,162 papers which are published in Scopus database in year 2010 by Malaysian top five universities. Then we developed a software to collect the number of citations and versions of each paper from Google Scholar automatically. The result of spearman correlation coefficient revealed that there is positive significant association between the number of Google Scholar versions of a paper and the number of times a paper has been cited.

This study analyzes the modeling and dynamics of a novel passive in Multi-Degree-of-Freedom (MDOF) vibration isolation platform which can achieve significant isolation effect. Symmetrical Scissor-Like structures (SLSs) are utilized in the proposed MDOF isolation platform as the supporting and isolation elastic components. Based on the mathematical modeling and theoretical analysis of the MDOF vibration isolation system with SLSs, the effect of structural parameter and joint friction on stiffness and damping properties is investigated. It is shown that due to geometric relations within the SLSs, the natural frequencies can be reduced via adjusting structural parameters of the SLS for different direction vibration isolation. Theoretical and experimental results show that the SLS isolation platform can achieve much better loading capacity and vibration isolation performance simultaneously by only using linear passive components because of the MDOF adjustable stiffness property. Therefore, with low costing and energy consumption, the proposed novel isolation platform can provide the improvement of vibration suppression in various engineering practices.

In the paper, the authors survey integral representations of the Catalan numbers and the Catalan–Qi function, discuss equivalent relations between these integral representations, supply alternative and new proofs of several integral representations, collect applications of some integral representations, and present sums of several power series whose coefficients involve the Catalan numbers.

(1) Background: The goal of the study was to evaluate psychological tolerance and health-related quality of life (QOL) in head and neck (HN) cancer patients treated with definitive accelerated radiotherapy (DART); (2) Methods: Seventy-six recurrence-free patients eligible for the study, who were treated with DART in the CAIR-2 phase III clinical study (median of follow-up=47 months), completed EORTC QLQ-C30 with H&N35 module, Hospital Anxiety and Depression Scale (HADS) and Visual–Analog Scales (VAS) of pain in HN and the neck / arm area.; (3) Results: The most dominating symptoms measured with QLQ-C30 were: fatigue (44/100), sleeplessness (39/100), financial problems (38/100) and pain (32/100). Within H&N35 the highest scores were reported on the subscales of sticky saliva (60/100), mouth dryness (65/100) and increased intake of painkillers (50/100). Pain (VAS) was reported by 87% (HN area) and 78% (shoulder) of the patients, with a mean score of 3/10. One-third reported depressive mood (HADS≥15 points) with an average score of 12.5/42 p. The depressed group, who smoked more as compared to non-depressed before DART (96% vs 78%) and required steroids treatment (85% vs 58%) during DART, also scored significantly worse on 23 of 35 subscales of QLQ-C30 and H&N35 and experienced more intense pain (VAS). Women, and less advanced patients scored better in several aspects of the quality of life; (4) Conclusions: Patients treated with DART struggle with low quality of life and persisting treatment-related symptoms including constant pain. HNC survivors, especially those, who are depressed, may require additional psychosocial, rehabilitation and medical intervention programs..

Coronary artery disease (CAD) represents a modern pandemic associated with significant morbidity and mortality. The multi-faceted pathogenesis of this entity has long been investigated, highlighting the contribution of systemic factors such as hyperlipidemia and hypertension. Nevertheless, recent research has drawn light to the importance of geometrical features of coronary vasculature on the complexity and vulnerability of coronary atherosclerosis. Various parameters have been investigated so far, including vessel-length, cross-sectional area, curvature, and tortuosity, using primarily invasive angiography and recently non-invasive cardiac computed tomography angiography (CCTA). It is clear that there is correlation between geometrical parameters and both the haemodynamic alterations augmenting the atherosclerosis-prone environment and the extent of plaque burden. The purpose of this review is to discuss the currently available literature regarding this issue and propose a potential non-invasive imaging biomarker, the geometric risk score, which could be of importance to allow early detection of individuals at increased risk of developing CAD.

Background: Overweight and obese adults seek effective exercise interventions to reduce accumulated fat, but the effectiveness of these interventions vary across studies. The purpose of this meta-analysis was to investigate the effectiveness of exercise interventions in overweight and obese adults based on measurement of accumulated fat distributions. (2) Methods: Databases were used to select eligible studies for this meta-analysis. Randomized controlled trials with a control and experimental group were included. Degrees of effectiveness of exercise interventions were computed to assess the benefits on reducing weight and subcutaneous, visceral, and ectopic fat accumulation. (3) Results: A total of twenty-one studies were included in this meta-analysis. Participation in exercise interventions showed beneficial effects in reducing weight and subcutaneous and visceral fat. The effectiveness of exercise interventions on ectopic fat accumulation could not be assessed due to the limited number of studies measuring ectopic fat. Additionally, effectiveness of exercise interventions that depended on measurements of accumulated fat varied. The average exercise intervention for overweight and obese individuals was moderate to vigorous intensity, 4 times per week, 50 minutes per session, and 22 weeks duration. (4) Conclusions: Participating in exercise interventions has favorable effects on reducing weight and accumulation of subcutaneous and visceral fat.

Pb found in rain water is not only caused by tin roof on houses but also caused by the pollution of industrial activities, vehicles and land clearing activity by fire. Pb pollutant dissolves and enters into rain water storages and it’s consumed as drinking. Pb can cause bad impact to human, for example disruption of enzyme, anemia and low intelligence. The purposes of this research are (1) to evaluate Pb, pH and turbidity level in rain water, (2) to analyze the effectiveness of mollusk sand filtration and the absorption of activity carbon to decrease Pb, turbidity and pH, and (3) to analyze the correlation of Pb, length of stay and smoking habit on public health. This research is an experimental by using pre and post test designs with control and observational by using cross sectional design. The research was conducted in urban and rural areas of Pontianak and Kubu Raya regency. The sampling was done in determining the number of samples of Pb, pH and turbidity in rain water. The analyzing the data by using computer program. The results show that: (1) the average of Pb, pH and turbidity level before treatment is considered high at 131.7 µg/L on Pb, turbidity at 20 NTU and low pH at 5.2. After the treatment was the Pb has decreased to 0.71 µg/L and turbidity has to 5.66 NTU, pH to 6.9 and (2) Rain water treatment is very effective to decrease Pb for 99.4% and turbidity for 72%, and (3) there is a correlation among Pb found in rain water, length of stay and smoking activity to public health. Recommends that: the residents of Pontianak and Kubu Raya to process rain water before consuming. The rain water treatment can be done by applying mollusk sand filtration and absorption of active carbon.

The development of language and communication patterns has been significantly impacted by the internet's quick advancement. The ability to instantly communicate globally and engage with people of different linguistic origins is one of the main advantages of using the internet. Internet use has significant positive effects on language growth, but it also brings with it drawbacks that need to be addressed. Online communication's casual atmosphere can occasionally cause grammar norms to deteriorate and non-standard language patterns to proliferate. With the information stated in this paper, the aim now is to collect literature on the benefits of internet usage and the evolution of language to provide substantive information in regard to this matter. In order to assist students in navigating the complexity of Internet communication, educational institutions should incorporate digital literacy into their curricula. This involves upholding strict requirements for traditional language proficiency while teaching students how to use digital technologies efficiently. The Internet should be used to support the revitalization and preservation of endangered languages. This can entail setting up community forums, digital archives, and online learning portals where language users can interact and exchange resources.

Gradients of smooth functions with non-independent variables are relevant for exploring complex models and for the optimization of functions subjected to constraints. In this paper, we investigate new and simple approximations and computations of such gradients by making use of independent, central and symmetric variables. Such approximations are well-suited for applications in which the computations of the gradients are too expansive or impossible. The derived upper-bounds of the biases of our approximations do not suffer from the curse of dimensionality for any $2$-smooth function, and theoretically improve the known results. Also, our estimators of such gradients reach the optimal (mean squared error) rate of convergence (i.e., $\mathcal{O}(N^{-1})$) for the same class of functions. Numerical comparisons based on a test case and a high-dimensional PDE model show the efficiency of our approach.

A model of space-time is presented, whose origin is set before the appearance of any universe. It uses concepts of previous work, a central one being that the information about the laws of nature is stored locally everywhere in space such that all physical processes obey them. Since information storage is bound to matter or energy, space is assumed to consist of dark energy (DE), which thus assumes an importance far beyond its function as a stopgap for an energy deficit in our universe ( U ). The primordial state (PS) is a timeless and relatively large space of 3 dimensions described by a Wheeler DeWitt (WDW) equation, whose solution is interpreted as an arrangement of very many space quanta and possesses properties that remind of the time-honored concept of the unmoved mover. The comparison of WDW solutions belonging to different mass densities of the DE favors one in which the space quanta are mini black holes. This allows the space quanta to be imagined as mass points which are kept at a distance compatible with the quantum volume by the Pauli principle or something equivalent. Triggered by a dramatic increase in probability, the PS is followed by a time-controlled sequence of quantized expansion states (ES i ). The concomitant emergence of time occurs in a lightning huge crash, consuming almost all DE of the PS. The subsequent quantized ES i emerge from a WDW equation, novelly derived from a solution of the modified cosmic momentum equation, which classically describes an exponential space expansion (CS). The huge volme of the ES i is also used as size of the PS. Information is assumed to be geometrically stored in arrangements of space quanta similar to how genetic information is stored in DNA molecules. During the CS information must be transferred from already existing "information quanta" to new ones. This requires time, slows down the expansion and is taken into account by a friction term in the cosmological momentum equation thus modified. Since the Friedmann-Lemaître (FL) equation remains fully valid, the model is widely based on recognized equations, so that some results may be understood as interpretations.

This article is an early draft on a proposed alternative to the current Marxist mode of thought; one that seeks to reject the generally ill-conceived and dogmatic proposals formulated by Marx in favour of another predicated on the more unwavering emotional ideals of the philosophy that preceded it. It eliminates that dogmatic mode in favour of a wholly social society, one that is founded upon the Marxist superstructure and intends hence to capture that humanity and re-form particularly economic principles that are used to construct the utopia into what is instead an entirely socially idealised frame of living.

Aiming to improve medical diagnosis and treatment, artificial intelligence (AI) has emerged as a transformational force in the healthcare industry. In this article, we examine how AI is increasingly being used to improve healthcare, with an emphasis on how it is changing medical diagnosis and treatment. We explore the opportunities, threats, and ethical concerns of incorporating AI into healthcare practice. In addition, we feature important AI applications in radiology, pathology, cardiology, and cancer. AI has great potential to improve patient outcomes, diagnostic accuracy, and the ability to provide individualized treatment plans in the future if it is used and refined with care.

The etiology of Autism Spectrum Disorder (ASD) has been linked to both genetic and epigenetic factors. Among the epigenetic factors, exposure to valproic acid (VPA), an antiepileptic and mood-modulating drug, has been shown to induce characteristic traits of ASD when exposed during embryogenesis. Conversely, in animal models, Enriched Environment (EE) has demonstrated positive behavioral and neural effects, suggesting its potential as a complementary treatment to pharmacological approaches in central nervous system disorders. In this study, we utilized zebrafish to model ASD characteristics induced by VPA and hypothesized that sensory stimulation through EE could ameliorate the behavioral and neuroanatomical features associated with ASD. To test this hypothesis, we assessed social behavior, cerebellar volume, and Purkinje cell populations via histology and immunohistochemistry after exposing the fish to EE. The results revealed that zebrafish exposed to VPA exhibited social deficits, reduced cerebellar cortex volume, and a decrease in c-Fos-positive cells in the Purkinje layer. In contrast, VPA-exposed fish treated with EE showed increased socialization, augmented cerebellar cortex volume, and an elevation in c-Fos-positive Purkinje cells. These findings suggest that alterations induced by VPA may be ameliorated through EE treatment, highlighting the potential therapeutic impact of sensory stimulation in conditions related to ASD.

The objective of this work was to evaluate the roast time, weight loss and quality of coffee grain at four different roasting degrees, aiming to recognize and develop sustainable patterns to industrialize specialty coffees. Coffee (Coffea arabica L.), from eight producers, with scores between 80 and 83 from SCA classification, were used. Samples of 300 g were roasted in a cylindric rotative roaster, until the grains reached four different roasting profiles (Agtron scale 22.36, #33.64, #40.05, #59.92). Afterwards, analysis of roasting time, gas pressure, weight loss, and sensorial grades were accomplished. It was observed that samples roasted at #22.36 led to significant differences, regarding roasting time and weight loss. Furthermore, there is a significant difference at the sensorial grades of the coffee beverage. Comparing the roast degree #40.05 (standard used for specialty coffee) with the roast degree #22.36 (most used for commodities coffee), the first one has a gas consumption of 0.34 kg per coffee kg, whilst the second presented a gas consumption of 0.41 kg per coffee kg. Thus, from gas consumption, roast degree # 40.05 is the more sustainable option, along with the remaining parameters analyzed.

Phosphatase and tensin homolog (PTEN) is a negative regulator of the phosphoinositide 3-kinases/protein kinase B (PI3K/AKT) signaling pathway. Notably, its active site harbors a cysteine residue that is susceptible to oxidation by hydrogen peroxide (H2O2). This oxidation inhibits the phosphatase function of PTEN, critically contributing to the activation of the PI3K/AKT pathway. Upon stimulation of cell surface receptors, the activity of NADPH oxidase 2 (NOX2) generates a transient amount of H2O2, serving as a mediator in this pathway by oxidizing PTEN. The mechanism underlying this oxidation, occurring despite the presence of highly efficient and abundant cellular oxidant-protecting and reducing systems, continues to pose a perplexing conundrum. Here, we demonstrate that the presence of bicarbonate (HCO3-) promoted the rate of H2O2-mediated PTEN oxidation, probably through the formation of peroxymonocarbonate (HCO4-), consequently potentiated the phosphorylation of AKT. In essence, our findings consolidate the crucial role of HCO3- in the redox regulation of PTEN by H2O2, lead to the presumption regarding HCO4- as a signaling molecule during cellular physiological processes.

Gliomas are central nervous system (CNS) derived tumors that originate from glial cells and affect six per 100,000 people in the United States. They are the most common form of CNS neoplasm and are highly diffusely infiltrative to surrounding brain tissue. Gliomas of diffusive nature are classified into different subcategories: astrocytomas, oligodendrogliomas, and ependymomas. Computed tomography (CT) and Magnetic Resonance Imaging (MRI) are used to determine tumor category and spread which may dictate treatment options. This paper focuses on emerging treatments of chemotherapy management with temozolomide and Avastin as well as emerging immune modulation treatment with vaccinations, manipulation of cellular checkpoints CTLA-4 and PD-1, co-receptor modulation of neuropilin-1, CAR-T cell therapy, and CRISPR-Cas9 gene editing. The employment of TMZ and BEV has been supported in the literature, however, more research is necessitated to fully optimize regimens and to avoid immune- and toxicity-related effects of these drugs. Moreover, an even closer consideration is warranted for current immunotherapies as they are in their infancy compared to TMZ and BEV. Thus, although promising emerging treatment options, therapies involving cancer vaccines, ICIs, immune modulation of neuropilin-1, CAR-T, and CRISPR-Cas9 technology require further investigation into their long-term efficacy and utility in treating gliomas.

In Ethiopia, there are a lot of national and regional parks and the objective is to conserve wild animals and plants on site. Botanical gardens are essential to the study and preservation of plant biodiversity, both in situ and ex situ. Botanical gardens are vitally essential establishments that protect the environment from ever-increasing environmental concerns, provide recreational possibilities, educate the public about environmental issues, and carry out a variety of conservation and research projects. Their goal is to preserve collections of live plants with documentation for use in scientific study, preservation, exhibition, and teaching. Botanical gardens engage in a wide range of scientific endeavors, including the study of seeds, taxonomy, systematics, genetics, biotechnology, propagation, horticulture, public education, restoration ecology, and many other subjects. The functions of parks and botanical gardens include; scientific research, natural science, Reduction of Wind and Water Loss, shelter for Fish, Wild Habitat, Noise, Pollution Control, and Serving as a Buffer Zone.

Increasingly, firms are expected to implement ESG (Environment, Social, and Governance) mandates to appeal to the global market. However, this requires overcoming practical challenges and capitalizing on emerging opportunities. This paper conducts an in-depth analysis of the ESG practices of leading Korean global firms. The study selects five firms for case studies representing industries such as electronics, automotive, steelmaking, and chemicals. It examines ESG reports, performance indicators, and corporate disclosures of these firms. The analysis reveals the adoption of industry-specific ESG strategies, highlighting how these firms tailor their approaches to address unique industry challenges while aligning with global sustainability trends. Key findings include a strong emphasis on innovative solutions to ESG challenges, the integration of ESG into core business operations, and a balanced approach to economic, social, and environmental responsibilities. This study contributes to a broader understanding of how ESG practices are implemented in various industrial contexts, particularly in the dynamic and evolving landscape of Korean global businesses. It offers valuable insights and benchmarks for global companies, underlining the importance of contextualized and industry-specific ESG strategies in achieving sustainable and ethical business practices

The Fas associated Death Domain (FADD) is an adaptor protein that predominantly transduces apoptosis signal from death receptor (DR) to activate caspases, leading to the initiation of apoptotic signaling and the coordinated removal of damaged, infected, or unwanted cells. In addition to its apoptotic functions, FADD is involved in signaling pathways related to autophagy, cell proliferation, necroptosis, and cellular senescence, indicating its versatile role in cell survival and proliferation. The subcellular localization and intracellular expression of FADD play a crucial role in determining its functional outcomes, thereby highlighting the importance of spatiotemporal mechanisms and regulation. Furthermore, FADD has emerged as a key regulator in inflammatory signaling, contributing to immune responses and cellular homeostasis. This review provides a comprehensive summary and analysis of cellular dynamics of FADD in regulating of programmed cell death and inflammation through distinct molecular mechanisms associated with various signaling pathways.

More water utilities are adopting Aquifer Storage and Recovery (ASR) to balance long-term water supply and demand. Due to large implementation and operation costs, ASR projects need to be optimized, particularly for energy use, which is a major operating expense. This study examines the relationships among energy use, recharge, and recovery at two ASR projects in the western United States. The major finding is an economy of scale for recovery processes, but not for gravity-fed recharge processes. The economy of scale found is as follows: the energy intensity recovered decreases with volume. This suggests it is more energy-efficient to recover large volumes of water in one interval instead of recovering smaller volumes at more frequent intervals. The H2Oaks recovery process experienced a 78% decrease in energy intensity from 0 to 50,000 m3 recovered, while the Sand Hollow site experienced a 43% decrease in energy intensity from 0 to 50,000 m3 recovered. Statistical analyses of the recovery process showed p values lower than 0.0001, R2 values between 0.43 and 0.57, and a RMSE value between 0.55 and 2.1, indicating the presence of a moderate correlation between energy and volume. This economy of scale has been observed in multiple instances in water and wastewater treatment. This finding not only has applications to ASR but also all recovery or recharge wells, whether or not they are paired with each other. Furthermore, this study confirms the need for more reliable and accessible energy data to fully understand the implications of the energy–water nexus.

Starting from the analysis of the lack of positivity of the Cattaneo heat equation, the article addresses the thermodynamic relevance of the positivity constraint in irreversible thermodynamics, than is at least as important as the entropic constraints. The fulfillment of this condition in hyperbolic models leads to the parametrization of the concentration fields with respect to internal variables associated with the microscopic dynamics. Using Brownian motion theory as a landmarking example for deriving macroscopic transport equations from the equations of motion at the particle/molecular level, we discuss two typical problems involving hydrodynamic interactions at microscale: surface chemical reactions at a solid interface of a diffusing reactant, and mass-balance equations in a complex viscoelastic fluid, in which the physics of the interaction leads either to the overcome the parabolic diffusion model or to consider the parametrization of the concentration with respect to the degrees of freedom associated with the relaxation dynamics of the solvent fluid.

This paper identifies preschool teachers' sources of stress, the times they experience high stress, and their ways of coping with stress levels. The study was conducted using a phenomenological design, one of the qualitative research models. The data were collected through semi-structured interviews with 36 preschool teachers working with children aged 0-6 in state and private schools. As a result of the content analysis, stressors were identified primarily at both interpersonal (positive, and effective interactions), and organizational levels (school management, and leadership style). It was also found that intense stress was experienced when children were difficult to control, such as during sleeping, eating, and cleaning. Finally, these results confirmed that the teachers used active/active behavioral, and passive/avoidant coping strategies. However, it was understood that preschool teachers perceived stress negatively, and did not see stress as a personal development situation. These results are discussed in terms of their ramifications for preschool education.

Background: Robot-assisted laparoscopic surgery robot-assisted surgical system has gained significant popularity over open and laparoscopic interventions. However, given its high costs, it remains unclear what clinical advantages robot-assisted laparoscopic surgery offers over conventional laparoscopic surgery. Objective: This umbrella review aims to synthesize and compare the clinical outcomes of robot-assisted laparoscopic surgery versus conventional laparoscopic surgery for five surgical procedures. Inclusion criteria: All systematic reviews and meta-analyses published in the past five years that compared the clinical outcomes of conventional laparoscopic surgery and robot-assisted laparoscopic surgery for cholecystectomy, colectomy, hysterectomy, nephrectomy and/or prostatectomy were included. Methods: A systematic literature search was conducted in PubMed and Scopus. The quality of all included reviews was assessed with the AMSTAR 2 quality assessment tool. Each review’s study characteristics (and a list of primary sources) were extracted, along with the quantitative and qualitative data for the following ten clinical outcomes: blood loss, rate of conversion to open surgery, hospitalization costs, incisional hernia rate, intraoperative complication rate, postoperative complication rate, length of hospital stay, operative time, readmission rate and wound infection rate. Results: Fifty-two systematic reviews and (network) meta-analyses were included in this umbrella review, covering more than 1,288,425 patients from 1046 primary sources published between 1996 and 2022. The overall quality of the included reviews was assessed to be low or critically low. Robot-assisted laparoscopic surgery yielded comparable results as conventional laparoscopic surgery in terms of blood loss, conversion to open surgery rate, intraoperative complication rate, postoperative complication rate, readmission rate and wound infection rate for most surgical procedures. While the hospitalization costs of robot-assisted laparoscopic surgery were higher and the operative times of robot-assisted laparoscopic surgery were longer than conventional laparoscopic surgery, robot-assisted laparoscopic surgery reduced the length of hospital stay of patients in nearly all cases. Conclusion: Robot-assisted laparoscopic surgery achieved comparable results with conventional laparoscopic surgery for cholecystectomy, colectomy, hysterectomy, nephrectomy and prostatectomy based on ten clinical outcomes. Further research is needed to prove that robot-assisted laparoscopy is as safe and reliable as conventional laparoscopic surgery.

Salting influences microbial growth, enzymatic activity and biochemical reactions during ripening, thus contributing to the final quality of cheese. The aim of this study was to evaluate the influence of different salting methods (dry salting at 12, 24 and 48 h; in brine; and curd salting) on the chemical (moisture and salt content), physico-chemical (pH, titratable acidity and water activity) and sensory (texture profile analysis, colour and sensory attributes) characteristics of an industrial blue vein cheese. Dry salted cheeses had lower moisture content and water activity, and higher salt/moisture content and acidity than those salted in brine and curd. Dry-salted cheeses were also characterised by higher values for hardness, fracturability and instrumental gumminess. Dry-salted cheeses showed differences only in the red/green colour component (a*), with the curd-salted cheeses being less greenish. All cheeses scored high (around 7) in the tasters' overall impression, with the dry-salted cheeses at 12 and 24 h showing optimal growth and even distribution of mould, as well as better flavour and texture.

The authors of the article analyze the existing methods and models of technological preparation of machine-building industries. The structure of a three-level simulation model with network-centric control, the structures of individual elements of the simulation model and the process of simulation modeling are described. The criteria for choosing a rational option for the processing technological route have been determined. During the research, a simulation program was implemented in C++. It allows you to select the optimal scenario for the operation of a production site based on two criteria: time and cost. The volume of implementation is about 2x103 lines of code. A diagram of the modeling algorithm for the implemented program, a description of the classes and their interactions are given in the article. The developed simulation model was tested at a machine-building enterprise using the example of the “Pusher” part, manufactured under single-unit production condi-tions. The technological equipment used for the manufacture of this part was formed in the form of input data of the simulation model. The results of simulation modeling for the selected part are described. For each variant of the technological processing route, the values of variable costs and the duration of the production cycle were determined.

The paper presents the results of the study of tungsten surface structure modification under helium plasma irradiation. It is revealed that during irradiation of samples, surface modification in the form of relief development as a result of irradiation is observed. X-ray phase analysis showed that no new phases of the W system were found after irradiation, only an increase in the intensity of diffraction lines was observed. There are significant differences in the microstructure of tungsten depending on the temperature of helium plasma irradiation in the above range. It is assumed that the cause of defects is the extremely low solubility of helium in tungsten. Metallographic analysis has shown that at irradiation of tungsten samples in regime 5 and 6 the degree of relief development is not high in comparison with the tungsten sample irradiated in regime 4. The greatest increase in roughness of the sample irradiated in regime 5 was determined, which is associated with the formation of small cracks, blisters and pores in the surface layer. At the same time, in the samples irradiated in regime 6, the surface of which is characterized by chaotically located protrusions and depressions of various shapes, the roughness parameter Ra was 0.0603 µm. It was found that at temperature regimes T = 1200 °C and T = 1500 °C the microhardness of tungsten increases by 11% and 10% respectively.

The regulation of intracellular pH in yeast (Saccharomyces cerevisiae) cells is critical for cell function and viability. In yeast, protons (H+) can be excreted from cell by the plasma membrane ATPase Pma1 and pumped into vacuoles by the vacuolar H+-ATPase. Because Pma1 is critical to the survival of yeast cells, it is unknown whether other compensatory components are involved in the pH homeostasis in the absence of Pma1. To elucidate how intracellular pH is regulated independently of Pma1, we employed a screening approach by exposing the yeast haploid deletion mutant library (ver 4.0) to the selective plant plasma membrane H+-ATPase inhibitor PS-1, which we previously reported. After repeated screenings and verification, we identified two proteins, ALY1 and ALY2, that play a role in the regulation of intracellular pH when Pma1 is deficient. Our research uncovers a new perspective on the regulation of intracellular pH related to Pma1 and also preliminarily reveals a role for ALY1 and ALY2 in the regulation of intracellular pH.

Gabapentin (GBP), a GABA analogue, is primarily used as an anticonvulsant to treat partial seizures and neuropathic pain. While a majority of the side effects are associated with the nervous system, emerging evidence suggests a high risk for heart diseases in the patients taking GBP. In the present study, we used a preclinical model of rats to investigate (1) the acute cardiovascular responses to GBP (bolus i.v. injection, 50 mg/kg) and (2) the effects of chronic GBP treatment (i.p. 100 mg/kg/day x 7 days) on cardiovascular function and the myocardial proteome. Under isoflurane-anesthesia, rat blood pressure (BP), heart rate (HR), and left ventricular (LV) hemodynamics were measured using Millar pressure transducers. The LV myocardium and brain cortex were analyzed by proteomics, bioinformatics, and western blot to explore the molecular mechanisms underlying GBP-induced cardiac dysfunction. In experiment (1), we found that i.v. GBP significantly decreased BP, HR, maximal LV pressure, and maximal and minimal dP/dt, whereas it increased IRP-AdP/dt, Tau, systolic, diastolic, and cycle durations (*p < 0.05 and **p < 0.01 vs baseline; n = 4/group). In experiment (2), we found that chronic GBP treatment resulted in hypotension, bradycardia, and LV systolic dysfunction, with no change in plasma norepinephrine. In the myocardium, we identified 109 differentially expressed proteins involved in calcium pathways, cholesterol metabolism, and galactose metabolism. Particularly, we found that calmodulin, a key protein of intracellular calcium signaling, was significantly upregulated by GBP in the heart but not in the brain. In summary, we found that acute and chronic GBP treatments suppressed cardiovascular function in rats, which is attributed to abnormal calcium signaling in cardiomyocytes. These data reveal a novel side effect of GBP independent of the nervous system, providing important translational evidence to suggest that GBP can evoke adverse cardiovascular events by depression of myocardial function.

Multiple drugs administration is a common practice in hospitals and clinics. This is the case when heavy pathologies are treated. In this context, frequently, antivirals and antibiotics are co-administrated either simultaneously or sequentially ignoring potential incompatibilities. In this study, we focused on an antiviral (Acyclovir) and an antibiotic (Ciprofloxacin) compatibility/incompatibility when they co-administrated with special interest on the effect of drugs ratio, pH and delay. By implementing robust HPLC method, we determined the main factors leading to potential modification of concentration of one of the two drugs in the mixture. The results showed that acyclovir is quantitatively recovered in all conditions related to pH, concentration and time (up to 24 hours). However, ciprofloxacin is strongly altered in acidic and basic conditions, the quantity of ciprofloxacin and time after mixing the two drugs. The most valuable piece of information is that the ratio of acyclovir/ciprofloxacin is crucial. The latter should be calculated and managed to provide at least two fold quantity of acyclovir versus ciprofloxacin in order to maintain the administrated doses and warrant efficient therapeutic effect.

In order to reduce the vibration of the transporter and improve the stability of the transporter, the vibration characteristics and key structure optimization research of the mountain orchard transporter are carried out. In this paper, the vibration of electric monorail transporters under different working conditions is tested, and the causes of vibration generated by monorail transporter during operation are explored. The three-dimensional model of the trailer and transmission box is established using Solidworks, and the modal vibration modes of the structure are analyzed theoretically. The modal test system is used for modal test analysis of trailers and transmission boxes. By comparing the results of finite element and experimental modal analysis, the second-order frequency of the trailer is close to the motor's rotating excitation frequency of 50 Hz at rated speed, which is easy to generate resonance. By optimizing the structure of the trailer, the second and third natural frequencies are increased to 54.79 Hz and 58.35 Hz respectively, which avoid the resonance of the trailer during operation and effectively reduce the vibration generated during the transportation of the trailer. Through vibration testing of the optimized electric monorail transporter, the results of vibration testing before and after structural optimization are compared and analyzed, and it is found that the vibration amplitudes of the transporter in X, Y and Z directions are reduced by 0.308m/s², 0.351m/s² and 0.334m/s² respectively, the running stability of the conveyer is improved.

In the interaction of the rolling stock and the upper structure of the railway track, intense dynamic loads occur. They have a destructive effect both on the parts of the rolling stock and on the elements of the superstructure of the track. In order to develop a durable, rational and reliably functioning design of cars and locomotives with good dynamic properties and good indicators of the impact of rolling stock on the railway track, along with theoretical computational studies, experimental studies are also required, which are usually the final stage in the design and implementation of rolling stock or modernization of existing ones. Locomotives and wagons in order to improve their strength and dynamic performance. The article presents the results of field tests to determine the dynamic performance of the type CKD6e diesel locomotive. The description of the preparation of the CKD6e shunting locomotive for testing is given. An analysis of the dynamic performance of a diesel locomotive during the passage of turnouts, on a straight section of the track and in a curve with a radius of 400 m, was carried out. The studies performed showed that the minimum value of the stability factor against wheel derailment on a straight section of the track is significantly higher than the standard value. The experimentally obtained ratio of frame forces to the static load from the wheelset on the rails, the coefficients of vertical dynamics of the first and second stages of suspension and the coefficient of stability against derailment of the wheel from the rail, registered on the track section in a curve with a radius of 400 m) meet the current requirements. A calculation scheme and equations of vertical oscillations are proposed, an analysis is carried out according to the graphs of movements of bogies and a locomotive body when moving along irregularities of different lengths at different speeds.

The fractional derivatives are a generalization the derivatives of integer order and find applications in studying memory processes in various scientific fields. Numerical methods are used to solve and analyze fractional models of real world problems. In this paper, we consider an approximation of the Caputo fractional derivative and its asymptotic formula, whose generating function is the polylogarithmic function. In the paper, we prove the convergence of the approximation and derive an estimate for the error and order. We consider an application of the approximation for the construction of finite difference schemes for numerical solution of the two-term ordinary fractional differential equation and the time-fractional Black-Scholes equation for option pricing. The properties of the approximation are used to prove the convergence of the methods used for numerical solution of the fractional differential equations. The theoretical results for the error and order of the methods are illustrated by the results of numerical experiments.

Obstetric Violence refers to dehumanized or derogative treatment of women in their pregnancy, childbirth or postpartum periods and may be manifested through the attitudes of health professionals or the performance of unjustified or outdated practices without maternal consent. Currently, there is no tool validated in Spain to measure women’s perception of obstetric violence. The objective of this study was to carry out the cultural adaption and validation of an existing 14-item Obstetric Violence Scale to the Spanish context, and to evaluate its psychometric properties. The research was conducted in two phases: first, a methodological study designed to evaluate content validity, through assessments by 8 experts (calculating the Aiken V coefficient) and face validity in a sample of 20 women; second, a cross-sectional study to evaluate construct validity (through confirmatory factor analysis and Rasch analysis), divergent validity against a scale of birth satisfaction, known groups validity and reliability. In Phase 1, Aiken V values higher than 0.71 were obtained for all items. Phase 2 was conducted on a sample of 256 women and the fit values for the unidimensional model were RMSEA: 0.070 [95%CI: 0.059-0.105] and GFI: 0.982 [95%CI: 0.823-0.990]. The Rasch analysis indicated poor performance of item 2, which was removed. The Omega and Cronbach's Alpha coefficients were 0.863 and 0.860, respectively. A final 13-item version of the Obstetric Violence scale was produced, with total score ranging from 0 (no obstetric violence perception) to 52 (maximum obstetric violence perception). The Obstetric Violence Scale is a reliable and useful tool to measure women's perception of obstetric violence.

The giant panda (Ailuropoda melanoleuca) is one of the most endangered species of land mammals and has significant academic research value worldwide. The evaluation of hematological parameters in giant pandas is important for assessing the physiological status of animals. This study collected blood samples from 12 healthy giant pandas from September 2018 to August 2020 under non-anesthetic conditions. The samples were then analyzed for basic blood indices and blood rheology, and normal values for hematological parameters and blood rheology under non-anesthetic conditions in giant pandas in Beijing area were obtained. The study confirmed the influence of age and season on hematological and biochemical parameters in captive giant pandas: hematological morphology, blood rheology, and serum enzymes showed seasonal variations, while age affected the changes in serum enzymes, serum protein content, and serum metabolite content. There are significant differences in blood indicators among different age groups of giant pandas, indicating variations in the overall metabolic processes and differences among pandas of different age groups. Seasonal variations showed a regulatory effect on blood rheology parameters and a negative effect on blood viscosity. Further research should be conducted to investigate whether factors such as season and climate cause environmental stress in captive giant pandas. The results obtained in this study aim to better protect the stability of the giant panda population and provide references for the appropriate feeding and medical care of captive giant pandas.

The municipal water supply, related mainly to the cities of Albanian, began to develop in the second half of the 19th century and much intensively after 1945. Today the reported mean water production for the cities, on average, is about 300 l/capita/d including drinking and industrial water supply. The territory of Albania consists of uneven distribution of very heterogeneous aquifers conditioning the reach variety of the municipal water supply solutions. In this article are analyzed and classified the hydrogeological aspects of water supply sources of the settlements, which are summarized in five groups: (a) Wells in alluvial intergranular aquifers; (b) karst springs; (c) wells in karst aquifers; (d) springs in fissured rocks, and (e) mixed water sources. For each group of the water supply sources the main concerns regarding the quantity and quality problems are analyzed facilitated by the description of a variety of representative examples of different situations. Based on the gained experience important recommendation are given for the better understanding of hydrogeological aspects of water supply systems emphasizing the problematics along the river water recharge areas and on the seawater intrusion in coastal aquifers, as well as on transboundary aquifers. However, the main problems of public water supply of Albania remain the poor management of water supply systems which is reflected in the e high water losses, as well as the low public awareness of request for sustainable use.

In this article, we have tried to extend the Neumann–Kopp law concerning the heat capacity of solid compounds to other physical observables for materials represented as mixtures of chemical compounds, alloys, and ceramics. The main goal of this study is to find the intervals of external or internal parameters for a solid compound, within which its physical observable - the magnetic transition temperature for this work, can be expressed in terms of the atomic or molar weighted sum of the magnetic transition temperatures of the constituent elements of a compound. Outside these intervals, we tried to figure out the structure of the variable by which the weighted sum should be multiplied. Thus, for USb–x(ThSb) mixtures with a mole fraction x from 0.36 to 0.55, the magnetic transition temperature of this mixture is expressed in term of the molar weighted sum of the temperature of uranium structural transition associated with a change in the magnetic properties of uranium and of the temperature at which the nature of the magnetic susceptibility of antimony changes. For the magnetic Laves phase compounds Er(Fe_0.8–xMn_0.2–yCo_x+y)₂, the Curie temperature of the compound is equal to the weighted sum of the Curie temperatures of all elements of the compound, except for Mn, at x = 0.1, y = 0 and y = 0.1. For the paramagnetic Curie temperature of intercalated dichalcogenides Cr_xМоSe₂, it can be expressed in terms of the weighted Neel temperature of chromium multiplied by a variable depending on x, on the atomic numbers of all elements of the compound, and on a parameter proportional to the derivatives with respect to x of the dichalcogenide’s crystal lattice parameters.

Cadmium (Cd) is a pervasive, toxic environmental pollutant that preferentially accumulates in tubular epithelium of the kidney. Current evidence suggests that the cumulative burden of Cd here leads to progress loss of the glomerular filtration rate (GFR). In this study, we have quantified changes in estimated GFR (eGFR) and albumin excretion (Ealb) in according to levels of blood Cd ([Cd]b) and excretion of Cd (ECd) after adjustment for confounders. ECd and Ealb were normalized to creatinine clearance (Ccr) as ECd/Ccr and Ealb/Ccr. Among 482 residents of Cd-polluted and non-polluted regions of Thailand, 8.1% had low eGFR and 16.9% had albuminuria, (Ealb/Ccr)×100 ≥ 20 mg/L filtrate. In the low Cd burden group, (ECd/Ccr) ×100 &lt; 1.44 µg/L filtrate, eGFR did not correlate with ECd/Ccr (β = 0.007), while an inverse association with ECd/Ccr was found in the medium (β =−0.230) and high-burden groups (β =−0.349). Prevalence odds ratios (POR) for low eGFR were increased in the medium (POR 8.26) and high Cd burden groups (POR 3.64). Also, eGFR explained a significant proportion of Ealb/Ccr variation among those with middle (η2 0.093) and high [Cd]b tertiles (η2 0.132), but did not with low tertile (η2 0.001). With adjustment of eGFR, age and BMI, POR values for albuminuria were increased in the middle (POR 2.36) and high [Cd]b tertiles (POR 2.74) and those with diabetes (POR 6.02) and hypertension (2.05). These data argue that ECd/Ccr of 1.44 µg/L filtrate (0.01−0.02 µg/g creatinine) could determine a Cd threshold level from which protective exposure guidelines should be formulated.

Innovation and technology are important tools of minerals sector efficiency and productivity im-provement. The uptake of technologies has proven important levelrs to improve the productivity of mining sector. This paper provides a comprehensive analysis of mine-level productivity by using a global data of copper, gold, and platinum from 1991-2020. Various drivers of proioductivity have been analysed to draw policy insights. Empirical findings reveal significant disparities in technical efficiency and productivity across mines and regions. A further decomposition of TFP into its different components suggest that the adoption of innovative practices and investment in technology adoption could improve the overall productivity of these commodities. The findings also suggest that an appropriate input mix and optimal scale of production could boost platinum mining productivity. Regional disparities in productivity in different commodities (e.g., South Africa vs. Zimbabwe) give policymakers with insights into how to support production scale and productivity through appropriate input mixtures.

In order to provide a new direction for the diagnosis and treatment of gastric cancer, the differentially expressed blood-based miRNAs in gastric carcinoma were obtained and analyzed from the datasets GSE113486, GSE112264 and GSE113740 by the SangerBox, the miRNA - target genes prediction, GO and KEGG functional enrichment analyses with DAVID 6.8, and the STRING database with Cytoscape, respectively. The correlation between the key miRNAs expression and the prognosis and diagnostic value of gastric cancer patients were detected by survival prognosis and ROC curve. QRT-PCR was used to detect the possible key miRNAs expression in human blood species. The dataset GSE108307 which shows the miRNAs affected by H. pylori infection was analyzed by GEO2R. The expression level of CagA and the clinically used gastric cancer markers were detected in human blood species for contrast. Five key blood-based miRNAs were determined, including hsa-miR-124-3p, hsa-miR-125a-3p, hsa-miR-29b-3p, hsa-miR-4276, and hsa-miR-575.The detection in human blood species as well as the cross analysis with H. pylori infection and clinically used markers expression suggested the importance and efficacy of the specific miRNAs in the early diagnosis and monitoring of gastric carcinoma. The study identified potential novel blood miRNA biomarkers of gastric cancer by bioinformatics and human blood species detection, which may give a new possibility of the important biomarkers for the diagnosis and prognosis of gastric cancer.

Powered lower limb exoskeletons (PLLE) have attracted much interest due to their potential applications. They provide assistance for persons with disabilities to accomplish activities of daily living (ADL), and more importantly assist them in achieving their rehabilitation goals. However, still there are unclear evidences on the quality and benefits that PLLEs can deliver to patients. This is due to limited usability and performance of current PLLEs, insufficient clinical use of PLLEs for different patients with high diversity in their disability type and impairment, and also the large gap between the technological state of the art and clinical expectations. In this study, we review and analyse various factors that can improve the effectiveness of PLLEs at yielding better assistance and rehabilitation training for patients with motor impairments. First, we define a set of criteria that characterize the majority of expectations for the rehabilitation and assistance domains and we use them for evaluating PLLEs depending on the context. Then, we include the effects of control strategies and combined approaches which include auxiliary devices such as Functional electrical stimulation and smart crutches applied to PLLEs with regard to the criteria we defined.

In order to reduce the silique shattering loss of rapeseed mechanical harvesting process, based on the state of force on the silique during rapeseed harvesting reel branch, Ningza 1810, Zhenyou 8 and Fengyou 306 were used as research objects, and the experimental research on the factors affecting rapeseed siliques shattering was carried out using the swing impact method. The experimental analysis showed that: rapeseed varieties, silique moisture content, silique growth position, collision material, impact speed, force position and other factors had significant effects on silique shattering. The impact velocity was less than 1.5m·s-1, the difference on the effect of each factor on pod-shattering was not significant, it was not easy to shatter when the moisture content of rapeseed silique was higher. The impact resistance of the front side of rapeseed was 2 to 4 times that of the bonding surface of rapeseed petals, the shattering rate of the top rapeseed silique was twice that of the bottom siliques, when siliques were supported, they were more likely to shatter under external forces than when they were unsupported. The experimental study of the mechanical properties of rapeseed siliques was carried out using the impending fracture method, the experimental analyses showed that the support position and force position of the silique, the loading speed and the growth position of the silique had a significant effect on the mechanical properties of the silique. The maximum cracking force was higher and bending strength was stronger when the body of the silique was supported, which the range of the maximum cracking force were 3.05N to 4.16N, and the bending strength range were 8.48 MPa to 11.57 MPa. The maximum cracking force and bending strength of the silique was stronger when the front side of the silique petal was pressurized than when the bonding surface of the petal was pressurized. Based on Pearson's correlation and grey correlation analysis, the morphological characteristics of rapeseed siliques were ranked in order of their influence on the performance of siliques in terms of the angle between silique and stalk, stalk diameter, petal thickness, beak length, silique thickness, silique width and silique length. This study can be used as a reference for the design and optimization of the rapeseed harvesting reel branch mechanism and the selection of machine harvestable rapeseed varieties.

The effect of graphene oxide (GO) on mechanical strengths and durability of cement composites has been studied by preparing GO-modified cement mortars. Thermogravimetric analysis (TGA) and nuclear magnetic resonance (29Si MAS-NMR) were performed on the cement paste to research the influence of GO on the hydration process and chain structure of calcium-silicate-hydrate (C-S-H) gels. In addition, mechanical strength test, such as compressive and flexural, were performed on cement mortars. The addition of GO at 0.05 wt.% (by weight of cement) increased the compressive strength by 9.02% after 28 days. Furthermore, the flexural strength of cement mortars with 0.05 wt.% GO and superplasticizer (SP) after 7 and 28 days increased by 12.26% and 21.86%, respectively, compared with reference mortar. At the same time, the effect of GO proved to be more significant and effective in the durability tests, suggesting that GO can enhance the microstructure through hydration products to create a highly cross-linked micro structure.

Today’s urban spaces face precipitous challenges and complications, which include the COVID-19 pandemic, urbanization, population growth, and climate change. Proximity plays an essential role in influencing the integrity of public spaces and urban environments, while proxemics studies people’s experience, and the benefits, of urban space, and is based on a behavioral system of activities that includes ‘territoriality’. There is a need to study the behavioural patterns of people in given situations with proxemic dimensions in order to sustain both human beings and the quality of urban space. However, people behave spontaneously within environmental settings and reflect each other’s responses, meaning it is important to distinguish between different cultures, which tend to respond in particular ways to the meaning of proximity. This suggests there is no universal indicator for phenomena such as crowding. The aim of this paper is to highlight the interrelationship between urban form and urban life. This study focuses on two patterns of activity - street life and social life - by adopting a descriptive-analytical approach to documentary and desk research. The findings reveal a vital distinction between social and public patterns of proximity, while other proximities, although critical, are not observed within interactions between people.

The quadratic polynomial differential systems in the plane are the easiest nonlinear differential systems. They have been studied intensively due to their nonlinearity and to their big number of applications. These systems can be classified in ten classes. Here we provide all the topologically different phase portraits in the Poincaré disc of two of these classes.

Indoor localization (IL) is a significant topic of study with several practical applications. The area of IL has evolved greatly in recent years due to the introduction of numerous technologies such as WiFi, Bluetooth, cameras, and other sensors. Despite the growing interest in this field, there are numerous challenges and drawbacks that must be addressed to develop more accurate and sustainable systems for IL and its real-life applications. This review study gives an in-depth look into IL, covering the most promising artificial intelligence-based and hybrid strategies that have shown excellent potential in overcoming some of the limitations of classic methods. In addition, the paper investigates the significance of high-quality datasets and evaluation metrics in the design and assessment of IL algorithms. Furthermore, this overview study emphasizes the crucial role that machine learning techniques, such as deep learning and transfer learning, play in the advancement of IL. A focus on the importance of IL and the various technologies, methods, and techniques that are being used to improve it. Finally, The survey highlights the need for continued research and development to create more accurate and scalable techniques that can be applied across a range of industries, such as evacuation-egress routes, hazard-crime detection, smart occupancy-driven energy reduction and asset tracking and management.

The implementation of grey and green infrastructure is an effective mean to address urban flooding and nonpoint source pollution, but due to the complexity of the process and the diver-sity of benefits, there is a lack of measurement for their comprehensive benefits. Adopting a typ-ical university in Beijing as an example, this paper simulated the multidimensional benefits of the water quantity, water quality, and ecology of grey and green facility renovation by coupling the storm water management model (SWMM) and InfoWorks Integrated Catchment Manage-ment (ICM). Monetization methods and economical means were employed to characterize the comprehensive benefits. The results showed that grey and green infrastructure retrofitting re-duces the number of severe overflow nodes in the study area by 54.35%, the total overflow vol-ume by 22.17%, and the nonpoint source pollution level by approximately 80% under the heavy rain scenario and 60% under the rainstorm scenario. The annual benefits of grey and green infra-structure renovation reached ¥765,600/year, of this amount, ¥83,100/year is from hydrological regulation, ¥454,100/year is from nonpoint source pollution reduction, and ¥228,300/year is from ecological improvement. The benefits of green facilities were higher than those of grey facilities, and the combined benefits were negatively correlated with the rainfall level, with a total bene-fit–cost ratio of 1.19. The results provide methodological and data support for grey and green in-frastructure retrofitting within the context of sponge cities.

We introduce new metric structures on a smooth manifold (called “weak" structures) that generalize the almost contact, Sasakian, cosymplectic, etc. metric structures (φ,ξ,η,g) and allow us to take a fresh look at the classical theory and find new applications. This assertion is illustrated by generalizing several well-known results. It is proved that any Sasakian structure is rigid, i.e., our weak Sasakian structure is homothetically equivalent to a Sasakian structure. It is shown that a weak almost contact structure with parallel tensor φ is a weak cosymplectic structure and an example of such a structure on the product of manifolds is given. Conditions are found under which a vector field is a weak contact vector field.

In recent decades, there have been numerous endeavors to develop a novel category of survival distributions possessing enhanced flexibility through the extension of existing distributions. This article constructs and validates the statistical properties of a novel survival distribution in order to obtain an alternative distribution that is suitable for analyzing survival data by presenting the novel mixture of the Fréchet distribution along with statistical properties such as the probability density function (PDF), cumulative distribution function (CDF), rth ordinary moment, skewness, kurtosis, moment-generating function, mean, variance, mode, survival function, hazard function, and asymptotic behavior, as well as constructing the estimators of the unknown parameter by employing the expectation-maximization (EM) algorithm, and simulated annealing. Additionally, the performance of the proposed estimators was compared with bias, mean squared errors (MSE), and simulated variances, and given an illustrative example of the proposed distribution to the survival data set in order to show that the proposed distribution is appropriate for the right-skewed data. This will be extremely advantageous in survival analysis.

EOR is a process that helps maximize recoverable oil reserves, extend field life and increase recovery rates, and is an important tool for companies to maintain production and increase return on investment. In this article, the performance of nanoclay on aqueous phase viscosity, wettability, and recycled oil in core fluidization in polyacrylamide nanofluid has been investigated in different experiments and EOR. We have used polymers due to the properties of polymers in increasing rheology and effective mobility and controlling stability and variability to resume growth oil in nanofluids. Adding 5% by weight of salt to polymer-clay nanofluid has also been investigated in samples comparable to pure nano clay without salt. The viscosity of this suspension increases by about 50% by adding a certain amount of salt. If the same amount of salt is added to the polymer diluent, the viscosity decreases drastically. The results of the wettability test also show that clay has a better potential to change the wettability in the tendency to salt. In core fluidization tests, the highest efficiency of 30% was obtained in the third recycling in the combination of clay nanoparticles and sulfone copolymer. The highest efficiency was obtained in the third scenario in core fluidization tests, that is; A combination of resin nanoparticles and sulfone copolymer. Their detailed behavior in the characteristics of wettability, rheology, and core fluidization is analyzed in this article.

Introduction: Osteosarcomas of the jaw (OSJ) are rare tumors with a different behavior from osteosarcomas of other bones. This study aims to analyze the clinical, pathological, and therapeutic characteristics of this type of sarcoma. Methods: a retrospective observational study of cases diagnosed with OSJ registered at the “La Paz” University Hospital (Madrid). Results: Eight cases with a diagnosis of OSJ were obtained in a study period of 22 years (2000-2022). The mean age was 41 years. The distribution was 1:1 between the maxilla and mandible. Painful inflammation was the most frequent clinical manifestation. Conventional osteoblastic osteosarcoma was the most common. Survival at 5 years was 50%, while at 10 years, it decreased to 25%. Conclusions: OSJ differs from conventional osteosarcomas of long tubular bones. Surgery continues to be the mainstay of treatment; more studies are needed in which more standardized protocols can be proposed for adjuvant therapeutic management.

Abstract: Using adjuvants to optimize and increase the efficacy of herbicides is an acceptable manner to reduce herbicides undesirable impact on the environment in sustainable agriculture. In this study, it was demonstrated that the application of 0.1% of the non-ionic surfactant (NIS, Contact) and 0.5 L ha-1 of a crop oil concentrate (COC, Renol) did not improve the efficacy of rimsulfuron on Amaranthus retroflexus. In contrast, the same treatments enhanced performance and rainfastnes of rimsulfuron in Chenopodium album in pot expriments. Increasing non-ionic surfactant concentration to 1 L ha-1 increased rimsulfuron performance around 11-fold for Amaranthus retroflexus compared to around 3-fold for Chenopodium album. The same treatment, also reduced the rainfastness of rimsulfuron on Amaranthus retroflexus while improving the rainfastness of rimsulfuron on Chenopodium album. Measured ED50 and ED90 values of rimsulfuron indicated that the addition of the 0.2 L ha-1 of NIS improved the recommended (60 g ai. ha-1) and the reduced (30 g ai. ha-1) of rimsulfurom in field. The highest potato yield measured (60 tons per ha) when 60 g ai. ha-1 rimsulfuron was applied at three stages (S1, S4, and S7) without using a NIS; not significant differences were measured when the same dose of rimsulfuron was applied at the three (S1, S4, and S7) and two (S1, S4) stages with NIS.

Activated carbon (AC) is an effective adsorbent for creatinine removal in hemoperfusion. However, the hemocompatibility and adsorption capacity of AC was required to be improved furthermore. Heparin, a widely used anticoagulant biomacromolecule, could improve the hemocompatibility of the absorbents in different ways based on its molecular weight. Thus, it was necessary to study the surface modification with unfractionated heparin (UFH) or low molecular weight heparin (LMWH) on improvement of hemocompatibility and adsorption. In this study, UFH and LMWH were respectively grafted on AC through polyethyleneimine as an intermediate layer. The modification of AC about morphology, mechanical strength and pore structure was characterized by XPS, SEM, TA and BET. It was found that compared with AC, the morphology and mechanical strength AC-UFH and AC-LMWH could be well maintained, but the BET surface was decreased due to the grafting of macromolecules. Furthermore, AC-UFH and AC-LMWH showed the better hemocompatibility on protein adsorption, APTT and platelet activation compared with AC, in which AC-LMWH had lower fibrinogen adsorption and longer APTT than AC-UFH. Besides, it was found that AC, AC-UFH and AC-LMWH had no significant effect on blood cell composition. Finally, the adsorption capacity of adsorbents for creatinine was evaluated. Although there was no significant difference between AC-UFH and AC-LMWH, it was found that heparin could be interacted with creatinine to enhance the adsorption capacity when compared with AC-PEI. This study deepened the understanding of anticoagulation of heparinized surface and provided a theoretical basis for adsorbents in hemoperfusion.

In this paper, under the symmetric entropy and the scale squared error loss functions, we consider the maximum likelihood (ML) estimation and Bayesian estimation of the Shannon entropy and Rényi entropy of the two-parameter inverse Weibull distribution. In the ML estimation, the dichotomy is used to solve likelihood equation. In addition, the approximation confidence interval is given by the Delta method. Because the form of estimation results is more complex in the Bayesian estimation, the Lindley approximation method is used to achieve the numerical calculation. Finally, Monte Carlo simulations and a real data set are used to illustrate the results derived. By comparing the mean square error between the estimated value and the real value, it can be found that the performance of ML estimation of Shannon entropy is better than that of Bayesian estimation, and there is no significant difference between the performance of ML estimation of Rényi entropy and that of Bayesian estimation.

A review on several classical, algebraic models in nuclear structure physics, which use symmetries as an important tool, are presented. After a conceptual introduction to group theory, a selection of models is chosen to illustrate the methods and the power of the usage of symmetries. It enables to describe very involved systems in a greatly simplified manner. Some problems are also discussed, when ignoring basic principles of nature, as the Pauli Exclusion principle. We also show that, nevertheless, occasionally one can rescue these omissions. In a couple of representative models, applications of symmetries are explicitly applied, in order to illustrate how extremely complicate systems can be treated. This contribution is meant bas a review on the use of algebraic models in nuclear physics, leading to a better understanding of the articles in the same special volume.

Oxidative stress and inflammation are basic pathogenic factors involved in tissue injury, pain, as well as acute and chronic diseases. Since long-term uses of steroids and non-steroidal anti-inflammatory drugs (NSAIDs) cause severe adverse effects, novel effective materials with minimal side effects are required. In this study, polyphenol content and antioxidative activity of rosebud extracts from 24 newly-crossbred Korean roses were analyzed. Among them, Pretty Velvet rosebud extract (PVRE) were found to contain high polyphenols and to show in vitro antioxidative and anti-inflammatory activities. In RAW 264.7 cells stimulated with lipopolysaccharide (LPS), PVRE down-regulated mRNA expression of inducible nitric oxide synthase (iNOS) and cyclooxygenase-2 (COX-2), and thereby decreased nitric oxide (NO) and prostaglandin E2 (PGE2) production. In an air-pouch inflammation model, treatment with PVRE decreased λ-carrageenan-induced tissue exudation, infiltration of inflammatory cells including neutrophils, monocytes and lymphocytes, and tumor necrosis factor-α and interleukin-1β concentrations, as achieved with dexamethasone (a steroid). Notably, PVRE also inhibited PGE2, similar to dexamethasone and indomethacin (an NSAID). The anti-inflammatory effects of PVRE were confirmed by microscopic findings, attenuating tissue erythema, edema, and inflammatory cell infiltration. These results indicate that PVRE exhibits dual (steroid- and NSAID-like) anti-inflammatory activities by blocking both the iNOS ― NO and COX-2 ― PG pathways, and that PVRE could be a promising anti-inflammatory material for diverse issue injuries.

Background: Knowledge of vascular anatomy and its possible variations is essential for performing embolization or revascularization procedures and complex surgery in the pelvis. The obturator artery (OA) is a branch of the anterior division of the internal iliac artery (IIA), and it has the highest frequency of variation between branches of the internal iliac artery. Possible anomalies of the origin of the obturator artery (OA) should be known when performing pelvic and groin surgery, where its control or ligation may be required. The purpose of this systematic review and meta-analysis, based on Sanudo’s classification, is to analyse the origin of the obturator artery (OA) and its variants. Methods: Thirteen articles, published between 1952 and 2020, were included in this systematic review and meta-analysis. Results: The obturator artery (OA) was present in almost all cases (99.8%): the pooled prevalence estimate for internal iliac artery (IIA) was 77.7% (95% CI 71.8% – 83.1%) vs 22.3% (95% CI 16.9% – 28.2%) for the external iliac artery (EIA). In most cases, the obturator artery (OA) originated from the anterior division trunk of the internal iliac artery (IIA) (61.6%). Conclusion: Performing preoperative radiological studies to know the pelvic vascular pattern and having awareness to evaluate possible changes in the obturator artery can reduce the risk of iatrogenic injury and complications

In this paper, we investigate the effects of mean stress, multiaxial loading, and residual stresses on the fatigue life of springs. We study the fatigue life of a homogeneously stressed material subjected to cyclic loading with nonzero mean stress. Traditional methods for estimating fatigue life are based on Goodman and HAIGH diagrams. The formal analytical descriptions, namely "stress-life" and "strain-life" approaches, are found to be more suitable for the numerical methods. The fatigue analysis method described above, which describes crack growth per cycle, is extended. The extensions allow consideration of the mean stress of a load cycle. Closed-form expressions for crack length versus number of cycles are derived. The complementary effects on the fatigue life of springs, which ultimately have a significant influence on the fatigue life of springs, are summarized. For the proposed unified fatigue life functions, the ranges for the stress loading factor are extended by introducing the effective stress intensity. The solution leads to the factor range for the effective stress intensity, the effective mean value of the stress intensity factor and the effective stress ratio. The developed method assumes the homogeneous stress state in the whole spring element. For the non-homogeneously loaded structural elements, the weak-link concept is applied to account for fatigue.

The common dandelion uses a bundle of drag-enhancing bristles (the pappus) that enables seed dispersal over formidable distances; however, the scaling laws of aerodynamic drag underpinning pappus-mediated flight remains unresolved. In this paper, we study the aerodynamic shape of dandelion, derive the scaling law of resistance, determine the Vogel exponent. In particular, we find that the total drag coefficient is proportional to the -2/3 power of the dandelion pappus Reynolds number, and obtain the terminal velocity of the dandelion seed under gravitation field.