The model internal year-to-year variability (hereafter, internal variability) is a significant source of uncertainty when estimating anthropogenic aerosol effective radiative forcing (ERF). In this study, we investigate the impact of internal variability using large ensemble simulations (600 years in total) with the same climate model under prescribed anthropogenic aerosol forcings. A comparison of the magnitudes (i.e., standard deviation, Std) of these influences confirms that internal variability has negligible impacts on the instantaneous radiative forcing (RF) diagnosed by double radiation calls but has considerable impacts on estimating ERF through rapid adjustments (ADJ). Approximately half of the model grids exhibit strong internal variability influence on ERF (Std > 5 W m−2). These strong internal variabilities lead to a 50% probability that 30-year linear change can reach 2 W m−2, and 10-year linear change can reach 4 W m−2. A 50-year simulation can provide a relatively stable annual mean map of ERF (ERF = ADJ + RF), but it fails for ADJ. The statistically significant areas in the annual mean maps of both ERF and ADJ from a 10-year simulation exhibit instability with evident chaotic features. These analyses contribute to the setup of comparative experiments and a more comprehensive understanding of the modeled anthropogenic aerosol ERF.

Abstract: A two-year study of pearl millet-groundnut cropping systems across two fertilizer levels was conducted at the INRAN/TARNA research station in Maradi, Niger in the Sahelian zone of West Africa. The objective of this study was to identify the best cropping system with and without fertilizer application to optimize pearl millet and groundnut yields, land use efficiency, and economics as measured by value-to-cost ratio. The experiment was conducted with three replications, and ten treatments combination of five pearl millet and groundnut cropping systems (pearl millet and groundnut sole crops, and three pearl millet – groundnut intercrops), and two fertilizer levels. Sole cropping produced the highest pearl millet grain by over 300 kg ha-1 and groundnut pod yields by over 500 kg ha-1, but all the intercropping systems had a LER above 1.0 with land use efficiency increased by 19 to 41%, also intercropping increased diversity, and reduced risk. Fertilizer application increased yields in all cropping systems by 200 to 600 kg ha-1. Government subsidy increased the value-to-cost ratio by 0.5 to 2, 5 units, and was required for economic response for pearl millet sole and intercrops in 2022. The groundnut sole cropping system had the greatest economic response to fertilizer application. Based on the risky environment and multiple end uses needed by producers, the intercrop system M-G: 1:3:1 with fertilizer application is usually the best option to optimize pearl millet and groundnut production.

This study evaluates the accessibility of primary care physicians (PCPs) in Eastern Quebec using an enhanced two-step floating catchment area (E2SFCA) methodology. The E2SFCA methodology considers both the population supply of PCPs and the travel time between PCPs and dissemination areas, and was found to be effective in identifying possibly underserved areas. The availability of primary care services is contingent upon the presence of adequate road infrastructure, and populations residing in areas with limited access to main road networks may experience compromised access to primary care. The study concludes that the E2SFCA methodology can facilitate the identification of areas experiencing a shortage of PCPs, and this information can be used to inform the development of regional medical workforce programs and support the establishment of rural residency initiatives.

Current trends in industrial development strive for maximum digitalization. The digital industrial revolution has been going on for more than a dozen years, Industry 4.0 and the idea of digital twins (DT) is becoming the focus of virtually all industrial sectors. Some sectors are more predisposed to digitalization, for others the process is much more difficult. This depends mainly on the specific characteristics and susceptibility of a given industry, including the current degree of digitalization of enterprises, as well as the knowledge and mental readiness of employees. The individual characteristics of an industry are important. Shipyards belong to the industry with a traditional approach, where the degree of digitalization remains low. As a result, the efficiency of shipbuilding processes and the quality of ships built are not sufficiently controlled. The article addresses this problem, reviews work in the field of digitalization of shipbuilding processes and points out the needs and challenges in this area. The article proposes the concept of a DT system for the entire ship design and production process. Key areas of digitalization of actual processes were defined, and a division was made into planning, monitoring and process analysis activities. Special attention was paid to the area of dimensional quality control and the Dimensional Quality Management Metasystem (DQMM) was featured in the comprehensive DT system. The requirements were defined and the limitations of the proposed solution were identified, taking into account a number of external factors including the degree of readiness of the manufacturer – the shipyard. The developed DT system concept was tested on the example of the construction process of a simplified ship. Practical aspects of the implementation of the proposed solution, in particular DQMM, were indicated.

Human motion analysis using inertial measurement units (IMUs) has recently been shown to provide accuracy similar to the gold standard, marker-based optical motion capture, but at much lower costs and while being less restrictive and time-consuming. However, IMU-based motion analysis requires precise knowledge of the orientation in which the sensor is attached to the body segments. This knowledge is commonly obtained via an anatomical calibration procedure based on precisely defined poses or motions, which is time-consuming and error-prone. In the present work, we propose a self-calibrating approach for magnetometer-free joint angle tracking that is suitable for joints with two degrees of freedom (DoF), such as the elbow, ankle, and metacarpophalangeal finger joints. The proposed methods exploit kinematic constraints to simultaneously identify the joint axes and the heading offset. The experimental evaluation shows that the proposed methods are able to estimate plausible and consistent joint axes from just ten seconds of arbitrary elbow joint motion. Comparison with optical motion capture shows that the proposed methods yield joint angles with similar accuracy as a conventional IMU-based method while being much less restrictive. Therefore, the proposed methods improve the practical usability of IMU-based motion tracking in many clinical and biomedical applications.

This study aims to explore the link between public investment and private investment in South Africa, using time series data spanning 40 years (1980–2020). Private investment is subdivided into credit to private sector (CPS) and foreign direct investment (FDI). Several econometric methodologies were used in the study, including the unit root test, cointegration test, and Error Correction Method (ECM). The Phillips-Perron (PP) test results point out that all the variables are stationary at levels with the exception of public investment (PI) which is stationary at first difference. The co-integration test reveals that the variables have a long-run equilibrium relationship. According to the findings of the ECM, public investment has a negative relationship with private investment (as measured by credit to private sector and foreign direct investment). The conclusion implies that in South Africa, public investment crowds out private investment. Other results revealed that, RGDP crowds in credit to private sector while crowding out foreign direct investment. Finally, the ECM findings show that government consumption expenditure crowds out credit to private sector and foreign direct investment. The residuals are homoskedastic and show no serial correlation, indicating that the model is adequate, according to the test for adequacy.

We follow the PRISMA extension for scoping reviews to review the emerging international body of empirical evidence on consumers’ attitudes and willingness to pay (WTP) for novel foods produced with New Plant Engineering Techniques (NPETs). NPETs include genome/gene editing, cisgenesis, intragenesis, RNA interference and others. These novel foods are often beneficial for the environment and human health and more sustainable under increasingly prevalent climate extremes. These techniques can also improve animal welfare and disease resistance when applied to animals. Despite these promising attributes, evidence suggests that many, but not all, consumers discount these novel foods relative to conventional ones. Our review sorts out findings to identify conditioning factors that can increase the acceptance of and WTP for these novel foods in a significant segment of consumers. International patterns of acceptance are identified. We also analyze how information and knowledge interact with consumer acceptance of these novel foods and technologies. Heterogeneity of consumers—across cultures and borders and in attitudes towards science and innovation—emerges as a key determinant of acceptance and WTP. Acceptance and WTP tend to increase when socially beneficial attributes—as opposed to producer-oriented cost-saving attributes—are generated by NPETs. NPET-improved foods are systematically less discounted than transgenic foods. Most of the valuation estimates are based on hypothetical experiments and surveys and await validation through revealed preferences in actual purchases in food retailing environments.

Ensuring a protection scheme in DC distribution is more difficult to achieve against pole-to-ground fault than in AC distribution system because of the absence of zero crossing points and low line impedance. To complement the major obstacle of limiting the fault current, several compositions have been proposed related to mechanical switching and solid-state switching. Among them, solid-state circuit breakers(SSCBs) are considered a possible solution to limit fast fault current. However, they may cause problems in circuit complexity, reliability and cost-related troubles due to the use of multiple power semiconductor devices and additional circuit configuration to commutate current. This paper proposes the SSCB with a coupled inductor(SSCB-CI) which has symmetrical configuration. The circuit is comprised of passive components like commutation capacitors, a CI and damping resistors. Thus, proposed SSCB-CI offers the advantages of simple circuit configuration and fewer utilized power semiconductor devices than another typical SSCBs in LVDC microgrid. For analysis, six operation states are described for the voltage across main switches and fault current. The effectiveness of the SSCB-CI against a short-circuit fault is proved via simulation and experimental results in a lab-scale prototype.

Ascorbate; Pars Plana Vitrectomy; Open Angle Glaucoma; Oxidative Stress; Vitreous Me-tabolism 0. How to Use This Template

Chronic rhinosinusitis is a common inflammatory disease of paranasal sinuses, which causes rhinorrhea, nasal congestion and hyposmia. The genetic predisposition or the exposure to irritants can sustain the inflammatory response and the development of nasal polyposis. Nasal polyps are benign and teardrop-shaped growths that project in the nasal cavities and originate from the ethmoid sinuses. This inflammatory process is associated with high expression of IL-5 cytokine and infiltration of eosinophils. Humanized monoclonal antibodies targeting IL-5 or its receptor, represent a therapeutic strategy in the treatment of nasal polyposis in combination with corticosteroids. The molecular pathogenesis of nasal polyps in CRS patients is associated to the epithelial-mesenchymal transition (EMT), a process in which epithelial cells lose their typical phenotype acquiring a mesenchymal phenotype. TGFβ/SMAD, ERK, and Wnt/β-catenin pathways are altered in EMT during the nasal tissue remodeling. miRNA and inhibitor molecules targeting these altered signaling pathways are able to interfere with EMT; which could lead to alternative therapies. Nasal polyps are an alternative source of mesenchymal stem cells which can be easily isolated from surgical biopsies. A molecular understanding of the biology of PO-MSCs will contribute to delineating inflammatory process underlying the development of nasal polyps.

Glacial relicts, especially those with very narrow habitat requirements, are particularly affected by global warming and thus good models for studying the future biodiversity patterns of the Alps. We have used as a model taxon Papaver occidentale, a glacial relict endemic to the Western Prealps, belonging to the alpine poppy complex (P. alpinum aggr.). All known localities were visited, each population was georeferenced and the number of individuals was estimated. Species Distribution Modelling (SDM) was used to evaluate the present and future potential distribution range and habitat suitability, taking into account the specificity of its habitat (calcareous screes). According to our study, there are globally 19 natural populations of P. occidentale. The total number of individuals was estimated at 30756 (with 72% of all individuals in canton of Bern). The taxon is a highly specialized alpine plant growing preferentially between 1900 and 2100 m a.s.l. on north facing screes. Predictions for the end of the 21st century indicate that suitable area will significantly decrease, for both the entire studied area (0-30% remaining) and sites nearby current P. occidentale populations (0-17% remaining). Under the most severe scenario, the species risks complete extinction. The long-term in situ conservation of P. occidentale, and all other taxa of the P. alpinum complex, is unlikely to be achieved without slowing global climate change. More generally, our fine-scale study shows that local environmental buffering of large-scale climate change in high-mountain flora may be very limited in specialised taxa of such patchy environments as screes.

Endometrial Cancer (EC) is the sixth most commonly occurring cancer in women with 380 000 cases in 2018. Sadly, EC morbidity and mortality are continuously increasing, therefore the medical society have a substantial need for an accurate and inexpensive diagnostic test for EC early detection and a prognostic tool for treatment planning and evaluation. Considering experience with different types of cancers C-reactive protein (CRP) appears to be a promising diagnostic and prognostic factor. Aiming to investigate its potential and in view of EC authors, this paper reviewed the following databases for metanalysis, randomized controlled trials and review articles published up to June 2020: Pubmed, Scopus, Google scholar and ClinicalKey. Studies indicate CRP >3.33 mg/l correlate with EC incidence with HR = 2.29 (p<0.05). Moreover, High-sensitivity CRP assay allows to detect CRP in very low concentrations and distinguish patients with endometriosis, soft tissue sarcomas and possibly EC. Preoperational and postoperational CRP, as well as its dynamic change are independent prognostic factors for EC and are more reliable if analyzed together. However, CRP-to-albumin ratio as well as Glasgow Prognostic Scale have greater prognostic value that CRP alone. Additionally, CRP is possibly a mediator of carcinogenesis and cancer progression through activation of inter alia FcgRs/MAPK/ERK, FcgRs/IL-6/AKT/STAT3 and FcgRs/NF-κB/NLRP3 pathways.

Peer-to-peer (P2P) content distribution or file sharing system aims to facilitate the dissemination of large files over unreliable networks. Network coding is a new transmission technique that has captured the interest of researchers because of its ability to increase throughput and robustness of the network, and decrease the download time. In this survey paper, we extensively summarize, assess, compare, and classify the most recently used techniques to improve P2P content distribution systems performance using network coding. To the best of our knowledge, this survey is the first comprehensive survey that specifically focuses on the performance of network coding based P2P file sharing systems.

Recently L-shaped tunneling field-effect-transistor (LTFET) has been introduced to overcome the thermal subthreshold limit of conventional metal-oxide-semiconductor field-effect-transistors (MOSFET). In this work, shortcoming of LTFET was investigated. It was found that corner effect present in LTFET effectively degrades its subthreshold slope. To get rid of corner effect a new type of device with dual material gates is presented. The new device termed as DG-LTFET gets rid of the corner effect and results in a significantly improved subthreshold slope of less than 10 mV/dec, and an improved ON/OFF current ratio over LTFET. In this work DG-LTFET was evaluated for different device parameters, and bench-marked against LTFET. This work presents an optimum configuration of DG-LTFET in terms of device dimensions and doping levels, to get the best subthreshold, ON current and ambipolar performance from the DG-LTFET.

Recent pollinator declines have focused efforts on their conservation which require clear estimates of pollination value to agriculture. Our socio-economic producer surveys and agronomic field research data were used to present a new way of estimating ecosystem service value of native pollinators. Using two regionally important U.S.A. crops, Maine wild blueberry and Massachusetts cranberry as models, we present perceived values of native bee pollinators from both consumer and producers. Wild blueberry’s Replacement Cost (RC) was greater than Attributable Net Income (ANI), since greater rented honey bee stocking densities are required. Attributable Net Income for native bees were similar for wild blueberry ($613/ha) and cranberry ($689/ha). Marginal Net Farm Income (MNFI) from incrementally adding more hives per ha was greater from stocking a third/fourth hive per ha for cranberry ($6,206) than stocking a ninth/tenth hive per ha for wild blueberry ($556), given greater responsiveness of yield, revenue, and profit to using rented honey bee hives in cranberry compared to wild blueberry. Both crops’ producers were only willing to annually invest $140–188/ha in native pollination enhancements on their farms, justifying government support. Consumers are willing to pay ~6.7 times more to support native bees than producers, supporting market-based support for invertebrate conservation.

At 8000 m and above, a ‘death zone’ reputation afforded protection for the fragile ecosystems of the Himalaya and Korakoram ranges for thousands of years. After decades of high-altitude mountaineering, environmental impacts have been documented such as associated carbon-intensive air travel and contamination from waste. Despite the growing popularity, high-risk and fragile context of the sport, the behaviour, perspectives and experiences of high-altitude mountaineers, and the social and economic consequences have not been researched. Following an interpretive paradigm and using purposive sampling, this qualitative study conducted in-depth interviews and open-ended survey questions to collect the experiences of sixteen high-altitude mountaineers. Analysis of the qualitative data was informed by Grounded Theory with the coding process leading to the overarching category of ‘leave no trace’. The results show how the high risks to life, and growing popularity of the activity influence mountaineer’s ability to act sustainably and increase unsustainable behaviour despite a desire to ‘leave no trace’ on the mountain. Meanwhile, climate change has already and will increasingly have profound impacts on the risks associated with 8000m mountaineering. Allowing more time for acclimation would help to address the root causes of unsustainable behaviours along with better enforcement of regulations.

As global concerns about climate change intensify, the need for effective strategies to reduce carbon emissions has never been more urgent. This paper explores the crucial role of data automation (DA) and decision support systems (DSS) in enhancing decarbonation efforts within the realms of solid waste management (SWM), wastewater treatment (WWT), and contaminated soil remediation (CSR). Specifically, the paper provides: (i) an overview of the carbon footprint (CFP) in relation to environmental management (EM) and the role of DA and DSS in decarbonization; (ii) DA case studies in areas of SWM, WWT, and CSR; (iii) 3. life cycle assessment (LCA) based DSS case studies in areas of SWM, WWT, and CSR; (iv) multi-criteria decision analysis (MCDA) based DSS case studies in areas of SWM, WWT, and CSR; and (v) optimal contractual delivery methods based DSS case studies in EM practices. The analysis disclosed that adoption of DA and DSS in SWM, WWT, and CSR holds significant potential for decarbonizing these EM processes. By optimizing operations, enhancing resource efficiency, and integrating renewable energy sources, these technologies contribute to the reduction of GHG emissions and promote sustainable environmental practices. As the demand for more effective and eco-friendly solutions grows, the role of DA and DSS will become increasingly pivotal in achieving global decarbonization goals.

This study examines the attitudes and practices of dentists and dental students towards envi-ronmental issues within their professional context. Data was selected based on their responses on a Google Forms e-questionnaire, designed specifically for the study. The sample consisted of 78 professional dentists and 75 dental students in Greece and their attitudes towards environmental protection, awareness of the environmental impact of dental practices, and factors influencing the adoption of environmentally friendly practices were assessed. Results reveal generally positive attitudes towards environmental protection, with students demonstrating higher levels of proper waste management practices. Dentists express awareness of their environmental impact but ex-hibit varying levels of engagement in eco-friendly practices. Factors such as moral consciousness and believing in the severity of climate change significantly influence environmental awareness in dental practice. Notably, dental students exhibit greater environmental awareness compared to practicing dentists. These findings emphasize the importance of integrating environmental edu-cation into dental curricula and continuing education programs to foster sustainable practices in dental care. Future research could explore interventions to enhance environmental consciousness among practicing dentists and assess the long-term impact of environmental education initiatives on dental care sustainability.

This study provides a detailed investigation into the pathways through which microplastics from urban sources are transported to marine ecosystems, their distribution across different environments, and their impacts on marine life. Utilizing a combination of water and sediment sampling across urban, riverine, and marine environments, the research quantitatively assesses the concentration and types of microplastics present, and evaluates the ecological consequences of their accumulation in marine ecosystems. The findings reveal a significant concentration of microplastics in all examined environments, with the highest levels detected in urban areas, closely linked to industrial activities and inadequate waste management practices. The study documents a variety of microplastic polymers, with polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET) being the most prevalent. A substantial impact on marine organisms was observed, including evidence of microplastic ingestion across a wide range of species and indications of stress and physical damage to coral reefs. Seasonal variations indicate that microplastic concentrations peak during periods of high rainfall, suggesting urban runoff as a critical pathway for microplastic transport. The study concludes with recommendations for improving waste management practices, enhancing public awareness and engagement in plastic recycling efforts, and implementing policies aimed at reducing the production and use of single-use plastics. This research underscores the urgent need for coordinated actions to mitigate the pervasive issue of microplastic pollution, highlighting the role of urban management and policy interventions in safeguarding marine ecosystems.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

White-rot fungi (WRF) have specific enzymes to degrade lignocellulosic and phenolic compounds. Therefore, their direct application could be an alternative to biodegrade complex lignocellulosic biomass such as olive mill solid waste (OMSW). The aim of this study was to evaluate the capacity of A. discolor and S. hirsutum to grow in OMSW as the sole substrate under static conditions and evaluate the phenolic removal compounds and lignin degradation. The lignolytic enzyme activity was determined, as was the phenolic compound removal. At the same time, lignin degradation and structural changes were evaluated by confocal laser scanning microscopy (CLSM) and scanning electron microscope (SEM), respectively. Both strains were able to grow using OMSW as the sole substrate without adding other nutrients, oxygen and/or agitation. The higher ligninolytic enzyme activity was found at day 8, and the highest phenolic removal (more than 80% with both strains) was reached after 24 days of incubation. The CLSM analysis confirmed lignin degradation through the drop in lignin fluorescence from 3967 for untreated OMSW to 235 and 221 RFU after 24 days of treatment by A. discolor and S. hirsutum respectively. The results indicate that both WRF could be suitable candidates to design an in-situ pretreatment step of OMSW, as long as in future research the WRFs have the same performance in non-sterile conditions.

Is it true that the nuclear technology applied to electric energy generation offers a clean, safe, reliable and affordable i.e. sustainable alternative? Yes it is, but its impact on the environment strongly depends on the implementation bearing residual risks due to a human factor, technical failures or natural catastrophes. A full response is therefore difficult and can first be given when the wicked multi-disciplinary problems get well formulated and “solved”. These problems have multi-dimensional nature lying at the interface between: necessary R&D effort, the industrial deployment and the technology impact in view of the environmental sustainability including the management of produced hazardous waste. This enormous complexity indicates that just a description of the problem might represent a problem. The paper proposes a holistic approach to assess the nuclear energy systems potential with respect to sustainable performance applying Multi-criteria decision analysis with a suitable objective tree and a multi-level criteria structure and examines the trading-off techniques for ranking of the alternatives. The framework proposes a multi-criteria and multi-stakeholders treatment which can be used as a pre-decisional support towards an implementation of nuclear fuel cycles adapted to national preferences and priorities. Proposed approach addresses some aspects of the environmental footprint of nuclear energy systems. Advanced nuclear fuel cycles, previously investigated by the NEA/OECD expert group WASTEMAN, are analyzed as a case study. Sustainability facets of waste management, resource utilization and economics are in focus.

A conventional electrical grid mostly depends on the electrical power generated from fossil fuels. However, the pollutants from fossil fuels are the key factors for adverse climate change. Most of the developed countries of the world have already recognized the fact that the energy mix requires to be diversified by incorporating renewable energy. This is especially relevant for many of the member countries of the Organization of Islamic Cooperation (OIC), consisting of 57 countries, whose abundance of fossil fuel reserve indicates that much of their electric power is still generated from fossil fuels. In order to integrate renewable energy sources into the hybrid energy mix, an existing conventional grid needs to undergo drastic changes. Alongside this, the population boom in the OIC member countries has caused higher demand for a steady supply of electricity that the conventional grids have long been struggling to cope with. With a view to solving this multifaceted problem, incorporation of the smart power management schemes is indispensable using a smart electrical grid, where information and communications technology is integrated into its major building blocks. This allows advanced applications of a grid, such as the formation of micro-grids, demand-side management, energy storage, high-tech power electronic converters, etc. As the smart grids are being adopted by many developed countries, it is high time for the OIC member countries to pay due attention to this development, if they have not already done so. This paper explains, with special focus on the OIC member countries, the various smart power management technologies, their operations and applications, and the benefits and challenges. Then it goes on to carry out the Strength-Weakness-Opportunity-Threat with Analytical-Heuristic-Procedure (SWOT-AHP) analysis to evaluate its feasibility of incorporation and the underlying strategies appropriate for its implementation. Furthermore, a Hybrid Multi-Criteria-Decision-Making (MCDM) analysis is performed to evaluate the sequence of the emphasis that should be given on each of the technologies from those available for the smart power management initiative. Finally, the study reinforces the stance by drawing parallels from the UN Sustainable Development Goals (SDG) and highlights the importance of the smart grid in line with the global vision of SDG. This paper aims at assisting the decision-makers in implementing smart power management schemes in the OIC member countries, in particular, and other countries of the world, in general.

This study introduces a robust methodology utilizing Multi-Criteria Decision Analysis (MCDA) combined with the Analytic Hierarchy Process (AHP) to repurpose abandoned hydrocarbon fields for energy storage, supporting the transition to renewable energy sources. We use a geostatistical approach integrated with Python scripting to analyze reservoir parameters—including porosity, permeability, thickness, lithology, temperature, heat capacity, and thermal conductivity—from a decommissioned hydrocarbon field in Southeast Hungary. Our workflow leverages stochastic simulation data to identify potential zones for energy storage, categorizing them into high, moderate, and low suitability scenarios. This innovative approach provides rapid and precise analysis, enabling effective decision-making for energy storage implementation in depleted fields.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

The prefabricated ECC/RC combined shear wall structure is an innovative prefabricated composite structure with better seismic performance by using ECC materials with better ductility in the main force and energy consumption regions of the prefabricated reinforced concrete (RC) shear wall structure. The key factors controlling the seismic energy dissipation capacity of this kind of structure are the use regions of ECC in composite coupling beams, use regions of ECC in shear walls, strength of ECC, stirrup ratio of coupling beams, strength of longitudinal reinforcement and so on. The parameters affecting seismic energy consumption are quantified by the finite element analysis method. By comparing and analyzing the load-displacement curves, hysteresis curves, energy dissipation capacity and stiffness degradation of the prefabricated ECC/RC combined shear wall structure specimen under these parameters, it is proposed that the best use regions of ECC is the cast-in-situ zone of the coupling beams with the scope of no more than400 mm at the shear walls’ bottom. The strength grade, the strength grade of longitudinal reinforcement, and the stirrup ratio of coupling beams are suggested design as E40, HRB400 and 0.5%, respectively.

Issues related to the duration of university studies, have attracted the interest of many researchers from different scientific fields, as far back as the middle of the 20th century. In this study, a Survival Analysis methodology, and more specifically a Cox Proportional hazards model, has been pro-posed to evaluate a theoretical framework/model that relates the risk a student either graduating on time or having a late graduation, with a number of observed and latent factors that have been proposed in the literature as the main determinants of degree completion. The major findings of the analysis suggest that the factors contributing to the shortening of the duration of studies in-clude high academic achievements at early stages, positive motivation, expectations, attitudes, and beliefs about studies. On the contrary, external situations, negative academic experiences and some individual characteristics of the students contribute to an extended duration of studies.

The aim of this research work consisted of assessing the effects of the COVID-19 pandemic on the interurban public transport system in a rural region with a sparse population density, considering the number of tickets sold and passengers in each locality, as well as the different connecting lines. From a methodological point of view and with the intention of identifying patterns to explain the behaviour of both routes and passengers, a series of variables were selected, becoming determining factors that sought to offer a solution to the search for a common trend. Additionally, data processing by means of statistical analysis and the application of Geographic Information Systems (GIS) tools complemented the procedure. The results obtained in the investigation were provided both by municipality and by interurban route. An interesting finding of the research was the uneven recovery of the municipalities. The localities closest to the attractor nucleus have recovered more quickly to pre-pandemic mobility levels due to their geographical proximity, larger population, higher income per household and the need to access certain public services. In terms of routes, all lines showed significant decreases in ticket sales, although with variations. Although passenger numbers have shown a gradual recovery, the initial loss was considerable, and pre-pandemic normality has not been completely achieved. The authors consider that future research should include other alternative means of transport in these interurban areas, incorporating variables to characterise passengers, such as age, gender...etc.

A “watch and wait” strategy, delaying treatment until active disease manifests, is adopted for most CLL cases; however prognostic models incorporating biomarkers have shown to be useful to predict treatment requirement. In our prospective O-CLL1 study including 224 patients, we investigated the predictive role of 513 microRNAs (miRNAs) on time to first treatment (TTFT). In the context of this study six well-established variables (i.e., Rai stage, beta-2-microglobulin levels, IGVH mutational status, del11q, del17p, and NOTCH1 mutations) maintained significant associations with TTFT in a basic multivariable model, collectively yielding a Harrell's C-index of 75% and explaining 45.4% of the variance in the prediction of TTFT. Concerning miRNAs, 73 out of 513 were significantly associated with TTFT in a univariable model; of these, 16 retained an in-dependent relationship with the outcome in a multivariable analysis. For 8 of these (i.e., miR-582-3p, miR-33a-3p, miR-516a-5p, miR-99a-5p, and miR-296-3p, miR-502-5p, miR-625-5p, and miR-29c-3p) a lower expression correlated with a shorter TTFT, whereas in the remaining eight (i.e., miR-150-5p, miR-148a-3p, miR-28-5p, miR-144-5p, miR-671-5p, miR-1-3p, miR-193a-3p, and miR-124-3p) the higher expression was associated with shorter TTFT. Integrating these miRNAs into the basic model significantly enhanced predictive accuracy, raising the Harrell’C index to 81.1% and the explained variation in TTFT to 63.3%. Moreover, the inclusion of the miRNA scores enhanced the Integrated Discrimination Improvement (IDI) and the Net Reclassification Index (NRI), underscoring the potential of miRNAs to refine CLL prognostic models and providing insights for clinical decision-making. In silico analyses on the differently expressed miRNAs revealed their potential regulatory functions of several pathways, including those involved in the therapeutic responses. To add a bio-logical context to the clinical evidence, a miRNA-mRNA correlation analysis revealed at least one significant negative correlation between 15 of the identified miRNAs and a set of 50 Artificial Intelligence (AI) selected genes, previously identified by us as relevant for TTFT prediction in the same cohort of CLL patients. In conclusion, the identification of specific miRNAs as predictors of TTFT holds promise for enhancing risk stratification in CLL to predict therapeutic needs. However, further validation studies and in-depth functional analyses are required to confirm the robustness of these observations and to facilitate their translation into meaningful clinical utility.

Concurrent Optical and Magnetic Stimulation (COMS) combines extremely low frequency electromagnetic and light stimulation modalities for enhanced wound healing. In this report, we investigated the potential mechanistic synergism between magnetic and light components by comparing their individual and combined cellular responses. Although each individual stimulation mode was capable of stimulating cell proliferation, magnetic fields exposure alone produced greater proliferation enhancement than light alone, yet their combined effects of were supra-additive of the individual responses. Reactive oxygen species were incrementally reduced by exposure to light, magnetics fields and their combination, where statistical significance was ultimately achieved. On the other hand, ATP production was significantly enhanced in response to magnetic exposure alone or in combination with light. These results suggest that mitochondrial respiratory efficiency was preferentially improved by the combination of the two stimuli. Protein expression related to cell proliferation was preferentially enhanced by the combinatory COMS modality as were the protein levels of the TRPC1 cation channel previously implicated as part of a calcium-mitochondrial signaling axis invoked by electromagnetic exposure and involved in proliferation. These results corroborate that light facilitates functional synergism with magnetic fields that ultimately impinge on mitochondria-dependent developmental responses. The aminoglycoside antibiotics (AGAs) have been previously shown to antagonize TRPC1-mediated magnetotransduction. Streptomycin applied during the exposure to any of the stimulation modes reduced proliferation enhancement, whereas streptomycin added after the exposure did not. Notably, the COMS modality and magnetic field exposure were capable of partially overcoming streptomycin antagonism of proliferation, whereas light alone was not. Transductional antagonism of combinatorial photon-electromagnetic effects by streptomycin thus aligns with previous studies showing that the AGAs block TRPC1-mediated magnetotransduction when applied during exposure. The prophylactic usage of the AGAs (neomycin) should be avoided during COMS therapy to maintain clinical efficacy and would be a common concern with most other electromagnetic regenerative paradigms.

Breast cancer is the most common cause of mortality due to cancer for woman both in Lithuania and worldwide. Chances of survival after diagnosis differ significantly depending on the stage of disease at the time of diagnosis and other factors. One way to estimate survival is to construct a Kaplan-Meier estimate for each factor value separately. However, in cases when it is impossible to observe a large number of patients (for example, in case of countries with lower numbers of inhabitants) dividing data into subsets, say, by stage at diagnosis may lead to results where some subsets contain too little data so that results of Kaplan Meier (or any other) method will become statistically incredible. The problem may become even more acute if the researcher would like to use more risk factors, such as stage at diagnosis, sex, place of living, treatment method, etc. Alternatively, Cox models are used to analyse survival data with covariates, and they don’t require dividing the data into subsets according to chosen risks factors (hazards).

Sums of M consecutive squared integers (a+i)^2 equaling squared integers (for a<=1, 0<= i<= M-1) yield remarkable regular linear features when plotting values of M in function of a. These features correspond to groupings of pairs of a values for successive same values of M around straight lines of equation mu*M = 2a and are characterized in this paper for rational values of mu.

Smart farm is a technology that greatly helps improve the productivity and quality of crops and is being actively introduced into indoor environments such as green houses. However, it has not yet been distributed to field-grown crops. The main reason is that, unlike indoor environments, it is very difficult to collect sensor data for monitoring the growth environment of crops in open fields where weather conditions change significantly and power supply is difficult. Additionally, because various sensors are used, the data formats of the devices are different, making it difficult to process. This paper presents a field crop growth environment monitoring and big data analysis system. The proposed system first solves power supply and data communication problems using solar power generation and LPWA technology. Additionally, based on the oneM2M architecture, data from various sensors is transmitted to the server using standardized technology. The transmitted data is stored and managed on the server as big data, and can be used to predict the production and quality of field-grown crops and take appropriate measures. The proposed system is expected to create an environment optimized for the growth of field crops and help prevent and manage diseases.

The main channel for disseminating information is now the Internet. Users have different expectations for the calibre of websites regarding the posted and presented content. The WEB site's quality is influenced by up to 120 factors, each represented by two to fifteen attributes. A major challenge is quantifying the features and evaluating the quality of a website based on the feature counts. One of the aspects that determines a website's quality is its completeness, which focuses on the existence of all the objects and their connections with one another. It isn’t easy to build an expert model based on feature counts to evaluate website quality, so this paper has focused on that challenge. Both a methodology for calculating a website's quality and a parser-based approach for measuring feature counts are offered. We provide a multi-layer perceptron model that is an expert model for forecasting website quality from the "Completeness" perspective. The accuracy of the predictions is 98%, whilst the accuracy of the nearest model is 87%.

Low-sodium salt substitute (LSSS) has the potential in regulating sodium and potassium intake and has been available in China market for years. However, its real-world use and impact to sodium\potassium intake is unclear. Baseline data of 4000 adult participants who participated in three similar-designed randomized controlled trails were pooled together for this study. Self-reported awareness and use of LSSS were collected using the uniform questionnaire, and the 24-h urinary sodium and potassium excretion was used to estimate their dietary intake. Mixed-effects models were developed to assess the relationship between LSSS and 24-h urinary sodium and potassium excretion. 32.0% of the participants reported awareness of LSSS and 11.7% reported its current use. After adjusting location, sex, age, and education, compared with the group of participants unaware of LSSS, participants who were aware but not using LSSS and those who were using LSSS had a lower 24-h urinary sodium excretion by –356.1(95% CI: –503.9, –205.9) mg/d and –490.6(95% CI: –679.2, –293.7), respectively (p&lt;0.001). No significant difference was found for 24-h urinary potassium excretion and sodium-to-potassium ratio among the three groups (p&gt;0.05). In conclusion, although associated with lower sodium intake, the awareness and real-world use of LSSS are still very low in China.

Invasive weeds cause significant crop yield and economic losses in agriculture. The highest in-direct impact may be attributed to the role of invasive weeds as virus reservoirs especially within the commercial growing areas. The new tobamovirus tomato brown rugose fruit virus (ToBRFV), recently identified in the Middle-East, overcomes the Tm-22 resistance allele in the cultivated tomato varieties grown in greenhouses. In this study, we determined the role of invasive weed species as potential hosts for ToBRFV and pepino mosaic virus (PepMV). Out of all tested weed species, the invasive species So-lanum elaeagnifolium and S. rostratum, mechanically inoculated with ToBRFV, were positive for To-BRFV in both enzyme linked immunosorbent assay (ELISA) and RT-PCR tests. S. rostratum was also positive for PepMV. No conspicuous phenotype was observed on ToBRFV infected S. elaeagnifolium plants suggesting a hostplant associated defense response. S. rostratum plants inoculated with either ToBRFV alone or a mixture of ToBRFV and PepMV-IL, contained high ToBRFV levels. In addition, when inoculated with ToBRFV or PepMV-IL disease symptom manifestations were observed in S. rostratum plants and the symptoms were exacerbated upon mixed infections with both viruses. The distribution and abundance of both Solanaceae species increase the risks of virus transmission between species.

Immune escape is observed with SARS-CoV-2 Omicron (Pango lineage B.1.1.529), the predominant circulating strain worldwide. Booster dose was shown to restore immunity against Omicron infection, however, real world data comparing mRNA (BNT162b2; Comirnaty) and inactivated vaccine (CoronaVac; Sinovac) homologous and heterologous boosting is lacking. A retrospective study was performed to compare the rate and outcome of COVID-19 in healthcare workers (HCWs) with various vaccination regime during a territory-wide Omicron outbreak in Hong Kong. During the study period 1 Feb – 31 Mar 2022, 3167 HCWs were recruited, 871 HCWs reported 746 and 183 episodes of significant household and non-household close contact. 737 HCWs acquired COVID-19 which were all clinically mild. Time dependent Cox regression showed that, comparing with 2-dose vaccination, 3-dose vaccination reduced infection risk by 31.7% and 89.3% in household contact and non-household close contact respectively. Using 2-dose BNT162b2 as reference, 2-dose CoronaVac recipient had significantly higher risk of being infected (HR 1.69 P<0.0001). Three-dose BNT162b2 (HR 0.4778 P<0.0001) and 2-dose CoronaVac + BNT162b2 booster (HR 0.4862 P=0.0157) were associated with lower risk of infection. Three-dose CoronaVac and 2-dose BNT162b2 + CoronaVac booster were not significantly different from 2-dose BNT162b2. The mean time to achieve negative RT-PCR or E gene cycle threshold 31 or above was not affected by age, number of vaccine dose taken, vaccine type and timing of the last dose. In summary, we have demonstrated lower risk of breakthrough SARS-CoV-2 infection in HCWs given BNT162b2 as booster after 2 doses of BNT162b2 or CoronaVac.

The option of decarbonizing urban freight transport using Battery Electric Vehicle (BEV) seems promising.However, there is currently a strong debate whether Fuel Cell Electric Vehicle (FCEV) might be the bettersolution. The question arises as to how a fleet of FCEV influences the operating cost, the Greenhouse Gas(GHG) emissions and primary energy demand in comparison to BEVs and to Internal Combustion EngineVehicle (ICEV). To investigate this, we simulate the urban food retailing as a representative share of urbanfreight transport using a multi-agent transport simulation software. Synthetic routes as well as fleet size andcomposition are determined by solving a Vehicle Routing Problem (VRP). We compute the operating costsusing a total cost of ownership (Total Cost of Ownership (TCO)) analysis and the use phase emissions as wellas primary energy demand using the Well To Wheel (WTW) approach. While a change to BEV results in 17 -23% higher costs compared to ICEV, using FCEVs leads to 22 - 57% higher costs. Assuming today’s electricitymix, we show a GHG emission reduction of 25% compared to the ICEV base case when using BEV. Currenthydrogen production leads to a GHG reduction of 33% when using FCEV which however cannot be scaled tolarger fleets. Using current electricity in electrolysis will increase GHG emission by 60% compared to the basecase. Assuming 100% renewable electricity for charging and hydrogen production, the reduction from FCEVsrises to 73% and from BEV to 92%. The primary energy requirement for BEV is in all cases lower and forhigher compared to the base case. We conclude that while FCEV have a slightly higher GHG savings potentialwith current hydrogen, BEV are the favored technology for urban freight transport from an economic andecological point of view, considering the increasing shares of renewable energies in the grid mix.

The importance of this study may be defined by using the smart techniques to earned value indicators of residential buildings projects in Republic of Iraq, only one development intelligent forecasting model was presented to predict Schedule Performance Index (SPI), Cost Performance Index (CPI), and To Complete Cost Performance Indicator (TCPI) are defined as the dependent. The approach is principally influenced by the determining numerous factors which effect on the earned value management, that involves Iraqi historical data. In addition, six independent variables (F1: BAC, Budget at Completion., F2: AC, Actual Cost., F3, A%, Actual Percentage., F4: EV, Earned Value. F5: P%, Planning Percentage., and F6: PV, Planning Value) were arbitrarily designated and satisfactorily described for per construction project. It was found that ANN has the capability to envisage the dust storm with a great accuracy. The correlation coefficient (R) has been 90.00%, and typical accuracy percentage has been 89.00%.

This paper presents an overview of the smart electro-clothing systems (SeCSs) targeted at health monitoring, sports benefits, fitness tracking, and social activities. Technical features of the available SeCSs, covering both textile and electronic components, are thoroughly discussed and their applications in the industry and research purposes have been highlighted. In addition, it also presents the developments in the associated areas of wearable sensor systems and textile-based dry sensors. As it became evident during the literature research, such a review on SeCSs covering all relevant issues has not been presented before. This paper will be particularly helpful for new generation researchers investigating the design, development, function and comforts of the sensor integrated clothing materials.

Over the past few decades, the growth of the urban population has been remarkable. Nowadays, 50% of the population lives in urban areas, and forecasts point that by 2050 this number will reach 70%. Today, 64% of all travel made is within urban environments and the total amount of urban kilometers traveled is expected to triple by 2050. Thus, seeking novel solutions for urban mobility becomes paramount for 21st century society. In this work, we discuss the performance of vehicular networks. We consider the metric Delta Network. The Delta Network characterizes the connectivity of the vehicular network through the percentage of travel time in which vehicles are connected to roadside units. This article reviews the concept of Delta Network and extends its study through the presentation of a general heuristic based on the definition of scores to identify the areas of the road network that should receive coverage. After defining the general heuristic, we show how small changes in the score computation can generate very distinct (and interesting) patterns of coverage, each one suited to a given scenario. In order to exemplify such behavior, we propose three deployment strategies based on simply changing the computation of scores. The results show that the strategies derived from the general heuristic are very interesting, all of them deploying roadside units in a circle pattern around the traffic epicenter.

Increased nutrient withdrawal by rapidly expanding intensive cropping systems, in combination with imbalanced fertilization, is leading to potassium (K) depletion from agricultural soils in Asia. There is an urgent need to better understand the soil K-supplying capacity and K-use efficiency of crops to address this issue. Maize is increasingly being grown in rice-based systems in South Asia, particularly in Bangladesh and North East India. The high nutrient extraction, especially K, however, causes concerns for the sustainability of maize production systems in the region. The present study was designed to estimate, through a plant-based method, the magnitude, and variation in K-supplying capacity of a range of soils from the maize-growing areas and the K-use efficiency of maize in Bangladesh. Eighteen diverse soils were collected from several upazillas (or sub-districts) under 11 agro-ecological zones to examine their K-supplying capacity from the soil reserves and from K fertilization (@ 100 mg K kg-1 soil) for successive seven maize crops grown up to V10-V12 in pots inside a net house. A validation field experiment was conducted with five levels of K (0, 40, 80, 120 and 160 kg ha-1) and two fertilizer recommendations based on “Nutrient Expert for Maize-NEM” and “Maize Crop Manager-MCM” decision support tools (DSSs) in 12 farmers’ fields in Rangpur, Rajshahi and Comilla districts in Bangladesh. Grain yield and yield attributes of maize responded significantly (P < 0.001) to K fertilizer, with grain yield increase from 18 to 79% over control in all locations. Total K uptake by plants not receiving K fertilizer, considered as potential K-supplying capacity of the soil in the pot experiment, followed the order: Modhukhali >Mithapukur >Rangpur Sadar >Dinajpur Sadar >Jhinaidah Sadar >Gangachara >Binerpota >Tarash >Gopalpur >Daudkandi >Paba >Modhupur >Nawabganj Sadar >Shibganj >Birganj >Godagari >Barura >Durgapur. Likewise in the validation field experiment, the K-supplying capacity of soils was 83.5, 60.5 and 57.2 kg ha-1 in Rangpur, Rajshahi, and Comilla, respectively. Further, the order of K-supplying capacity for three sites was similar to the results from pot study confirming the applicability of results to other soils and maize-growing areas in Bangladesh and similar soils and areas across South Asia. Based on the results from pot and field experiments, we conclude that the site-specific K management using the fertilizer DSSs can be the better and more efficient K management strategy for maize.

This paper deals with the environmental characterization of a large and densely populated area, with a poor reputation for contamination, considering the contribution of environmental features (air, soil, soil hydraulic and groundwater) and the potential effects on human health. The use of Geographic Information System (GIS) has made possible a georeferenced inventory and, by overlaying environmental information, an operational synthesis of comprehensive environmental conditions. The cumulative effects on environmental features were evaluated, taking into account superposition effects, by means of the spatial multicriteria decision analysis (S-MCDA). The application of the S-MCDA for converging the combination of heterogeneous factors, related to soil, land and water, deeply studied by heterogeneous groups of experts, constitutes the novelty of the paper. The results confirmed an overall higher potential of exposure to contaminants in the environment and higher mortality rates in the study area for some tumours, but hospital admissions for tumours were generally similar to the regional trend. Besides, mortality data may be strictly dependent on the poor socioeconomic conditions, quality of therapy and a lack of welfare in the area relative to the rest of Italy. Finally, as regards the possible relationship between presence of contaminants in the environment and health conditions of the population no definite conclusions can be drawn, although the present study encourages the use of the new proposed methods, that increase the possibilities for studying the combined effect of more environmental factors.

Intracellular aggregates of the alpha-synuclein protein result in cell loss and dysfunction in Parkinson’s disease and atypical parkinsonism, such as multiple system atrophy and dementia with Lewy bodies. Each of these neurodegenerative conditions, known collectively as alpha-synucleinopathies, may be characterized by a different suite of molecular triggers that initiate pathogenesis. The mechanisms whereby alpha-synuclein aggregates in turn mediate cytotoxicity also remain to be fully elucidated. However, recent studies have implicated the cell-to-cell spread of alpha-synuclein as the major mode of disease propagation between brain regions during disease progression. Here, we review the current evidence for different modes of alpha-synuclein cellular release, movement and uptake, including exocytosis, exosomes, tunnelling nanotubes, glymphatic flow and endocytosis. A more detailed understanding of the major modes by which alpha-synuclein pathology spreads throughout the brain may provide new targets for therapies that halt the progression of disease.

Marine litter, comprising persistent and human-made solid materials discarded in marine environments, poses a severe threat to Nigeria's coastal and marine ecosystems. Despite existing international, regional, and national regulations, ineffective enforcement and compliance have led to widespread environmental degradation (UNEP, 2021). This study examines the factors contributing to the proliferation of marine litter in Nigeria, focusing on regulatory gaps, insufficient waste management infrastructure, and the lack of public awareness. The findings reveal that the marine ecosystem is deteriorating due to inadequate waste disposal practices and limited understanding of the impacts of marine litter on both the environment and human health (UNEP, 2021). The paper concludes with recommendations for improving regulatory enforcement, enhancing public education, and investing in waste management infrastructure to address the growing crisis of marine litter. Throughout this article, the limited information on the impacts of marine pollution across Africa is highlighted, emphasizing the value of these insights despite their scarcity.

Industrial fires at facilities including waste management sites, warehouses, factories, chemical works and fuel storage depots are relatively frequent occurrences. Often, these fires occur adjacent to urban communities and result in ground-level airborne pollutant concentrations that are well above guideline values. Land, water, livestock and crops may also be contaminated by the emissions and by firefighting activities. Moreover, impacted communities tend to have a higher proportion of minority ethnic populations, individuals with underlying health vulnerabilities, as well as those of lower socio-economic status. Nevertheless, this is an aspect of air quality that is under-researched, and so this review aims to highlight the public health hazards associated with industrial fires and the need for an effective, coordinated, public health response. We also review the range of monitoring techniques that have been utilised in such fires and highlight the role of dispersion modelling in predicting plume trajectories and in estimating population exposure. We recommend establishing 1-h guideline values for particulate matter to facilitate timely public health interventions and we highlight the need to review regulatory and technical controls for sites prone to fires, particularly in the waste sector.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

UV-A (ca. 365 nm wavelength, a.k.a. 'black light') photocatalysis has been investigated to comprehensively mitigate odor and selected air pollutants in the livestock environment. This study was conducted to confirm the performance of UV-A photocatalysis on the swine farm. The objectives of this research were to (1) scale-up of the UV-A photocatalysis treatment, (2) evaluate the mitigation of odorous gases from swine slurry pit, and (3) test different UV sources, (4) evaluate the effect of suspended particulate matter (PM), and (5) conduct preliminary economic analyses. We tested UV-A photocatalysis at a mobile laboratory-scale capable of treating ~0.2 - 0.8 m3·s-1 of barn exhaust air. The targeted gaseous emissions of barn exhaust air were significantly mitigated (p < 0.05) up to 40% reduction of measured odor; 63%, 44%, 32%, 40%, 66%, and 49% reduction of dimethyl disulfide, isobutyric acid, butanoic acid, p-cresol, indole, and skatole, respectively; 40% reduction of H2S; 100% reduction of O3; and 13% reduction of N2O. The PM mitigation effect was not significant. Formaldehyde levels did not change, and a 21% generation of CO2 was observed. The percent reduction of targeted gases decreased as the airborne PM increased. Simultaneous chemical and sensory analysis confirmed that UV-A treatment changed the overall nuisance odor character of swine barn emissions into weaker manure odor with 'toothpaste and 'mint' notes. The smell of benzoic acid generated in UV-A treatment was likely one of the compounds responsible for the less-offensive overall odor character of the UV-treated emissions. Results are needed to inform the design of a farm-scale trial, where the interior barn walls can be treated with the photocatalyst, and foul air will be passively treated as it moves through the barn.

Environmental impact associated with odor and gaseous emissions from animal manure is one of the challenges for communities, farmers, and regulatory agencies. Microbe-based manure additives treatments are marketed and used by farmers for mitigation of emissions. However, their performance is difficult to assess objectively. Thus, comprehensive, practical, and low-cost treatments are still in demand. We have been advancing such treatments based on physicochemical principles. The objective of this research was to test the effect of the surficial application of a thin layer (¼"; 6.3 mm) of biochar on the mitigation of gaseous emissions (as the percent reduction, % R) from swine manure. Two types of biochar were tested: highly alkaline and porous (HAP) biochar made from corn stover and red oak (RO), both with different pH and morphology. Three 30-day trials were conducted with a layer of HAP and RO (2.0 & 1.65 kg∙m^-2, respectively) applied on manure surface, and emissions of ammonia (NH₃), hydrogen sulfide (H₂S), greenhouse gases (GHG), and odorous volatile organic compounds (VOCs) were measured. The manure and biochar type and properties had an impact on the mitigation effect and its duration. RO significantly reduced NH₃ (19-39%) and p-cresol (66-78%). H₂S was mitigated (16~23%), but not significantly for all trials. Significant (66~78%) reductions for p-cresol were observed for all trials. The phenolic VOCs had relatively high % R in most trials but not significantly for all trials. HAP reduced NH₃ (4~21%) and H₂S (2~22%), but not significantly for all trials. Significant % R for p-cresol (91~97%) and skatole (74~95%) were observed for all trials. The % R for phenol and indole ranged from (60~99%) & (29~94%) but was not significant for all trials. The impact on GHGs, isobutyric acid, and the odor was mixed with some mitigation and generation effects. However, larger-scale experiments are needed to understand how biochar properties and the dose and frequency of application can be optimized to mitigate odor and gaseous emissions from swine manure. The lessons learned can also be applicable to surficial biochar treatment of gaseous emissions from other waste and area sources.

This article attempts to identify factors impacting on the quantity of municipal waste in Polish 2478 communes (LAU-2), taking into account the variability of particular determinants influence depending on their regional diversification. The analysis covers the years 2005-2018. The dependent variable is the volume of municipal waste in kg per capita, whereas the group of determinants include: economic and human development, uncontrolled dumping sites, population density, population at the working age, migration, tourism, urbanization, dwellings and housing, retail sales, entities, education and investments in waste management; The geographically weighted regression with spatial error term (GWR-SEM) was employed in this study. The model enabled not only the specification of the waste production determinants, but also the analysis of the variability in the strength and direction of dependencies occurring between the examined variables in individual communes. The results proved that the higher the level of education the less waste is generated (in the north-central Poland); the business entities and working-age population are crucial for the waste quantity in communes of eastern Poland; the factors most considerably as to regional range affecting the waste quantity are urban and business development; as to strength–higher education and the share of working age individuals;

We introduce two symmetric concepts to physics: “distance” (space and time in one) and “wavematter” (electromagnetic wave packet and matter in one). We claim that physics has chosen the wrong concept of time: It is not aware that the time of a moving object flows in a direction other than my time. We provide 15 proofs for our claim by solving 15 mysteries of physics graphically! For example, we prove that length contraction and time dilation are actually geometrical effects in a 4D manifold that we call “Euclidean spacetime” (ES). We prove that the discrepancy in calculating the Hubble constant stems from a systematic error in the redshift measurement. We prove that what I deem wave, deems itself matter, which solves wave–particle duality. We even untangle quantum entanglement without the issue of non-locality. We finally understand why alternative theories of Euclidean relativity have failed: They are all based on four dimensions of space rather than distance. A huge amount of energy was injected into ES at a point that we take as origin. Ever since has this energy been moving radially away at the speed of light. We live in the 3D hypersurface of an expanding 4D hypersphere. Hyperspherical coordinates have the great advantage that they reduce all that is ever happening to just one formula. So, it is the Theory of Everything in these coordinates: “Energy is covering radial distance which, divided by Euclidean time, is equal to the speed of light.” Acceleration and force like gravitation emerge from a rotation of objects in ES and a subsequent projection to 3D space. Matching the symmetry simplifies physics.

The present studies are specifically aimed at investigating the sensitivity of different dynamic stall models when exposed to various excitation frequencies targeted at the blade edgewise vibrations. The work is done on a modified version of the IEA 15 MW reference wind turbine employing a wind turbine design tool Bladed. The state-of-the-art dynamic stall models for wind turbine applications such as the ye model, Beddoes-Leishman (BL) model and the newly developed IAG model are evaluated. The beginning of the research work starts by evaluating different dynamic stall model effects on rigid blade section forces against known airfoil datasets. Then, the blade flexibility is considered to enable systematic evaluations of the blade flexibility influences in comparison to the rigid blade cases. It is observed that the range of the angle of attack grows depending on the excitation frequency and the adopted dynamic stall model. The critical excitation frequency range and the effects of twist distribution are then identified from the studies, which can be useful as a rough guidance when designing wind turbine blades.

Within the phenomenology of particle physics, the theoretical model of 4-zero textures is validated using a chi-square criterion that compares experimental data with the computational results of the model. Traditionally, analytical methods that often imply simplifications, combined with computational analysis, have been used to validate texture models. In this paper, we propose a new meta-heuristic variant of the differential evolution algorithm that incorporates aspects of the particle swarm optimization algorithm called "HE-DEPSO" to obtain chi-squared values are less than a bound value, which exhaustive and traditional algorithms cannot obtain. The results show that the proposed algorithm can optimize the chi-square function according to the required criteria. We compare simulated data with experimental data in the allowed search region, thereby validating the 4-zero texture model.

The use of green hydrogen as a high-energy fuel of the future may be an opportunity to balance the unstable energy system, which still remains renewable energy sources. This work is a comprehensive review of recent advancements in green hydrogen production. The review outlines the current energy consumption trends. It presents the tasks and challenges of the Hydrogen Economy towards green hydrogen, including production, purification, transmission, storage, and conversion into electricity. This work discusses the main types of water electrolyzers: alkaline electrolyzers, proton exchange membrane electrolyzers, solid oxide electrolyzers, and anion exchange membrane electrolyzers. Despite the higher production costs of green hydrogen compared to grey hydrogen, the review suggests that as renewable energy technologies become cheaper and more efficient, the cost of green hydrogen is expected to decrease. The review highlights the need for cost-effective and efficient electrode materials for large-scale applications. It concludes by comparing the operating parameters and cost considerations of the different electrolyzer technologies. It sets targets for 2050 to improve the efficiency, durability, and scalability of electrolyzers. The review underscores the importance of ongoing research and development to address the limitations of current electrolyzer technology and to make green hydrogen production more competitive with fossil fuels.

Background: beta blockers of three generations are first-line drugs in the treatment of chronic heart failure (CHF). However, to date there is no clear understanding of the effect of beta blockers on myocardial energy metabolism disorders in CHF. The aim of the study: to conduct a study of beta-blockers of different generations on myocardial energy metabolism in the experimental CHF. Methods: CHF was modeled in white outbred rats by administering doxorubicin. The study drugs were administered intragastrically – new drug Hypertril (1-(β-phenylethyl)-4-amino-1,2,4-triazolium bromide)-3.5 mg/kg, metoprolol - 15 mg/kg, Nebivolol -10 mg/kg, Carvedilol 50 mg/kg, Bisoprolol, 10 mg/kg. In the myocardium, the main indices of energy metabolism were determined - ATP, ADP, AMP, malate, lactate, pyruvate, succinate dehydrogenase (SDH) activity, NAD-dependent malate dehydrogenase (NAD-MDH) activity. Results: traditional second-generation beta-blockers (Metoprolol and Bisoprolol) did not affect the studied indices of energy metabolism, and third-generation beta-blockers with additional properties - Carvedilol and, especially, Nebivalol and Hypertril improved myocardial energy metabolism. Conclusions: obtained results will help to expand our understanding of the effect of beta-blockers of various generations used to treat cardiovascular diseases on energy metabolism, and are also an experimental justification for the practical choice of these drugs in the complex therapy of CHF.

Drone technology has undoubtedly become an integral part of our everyday life these days. The business and industrial use of unmanned aerial vehicles (UAV) can provide advantageous solutions in many areas of life, and they are also optimal for emergency situations and for accessing hard-to-reach places. However, their application poses numerous technological and regulatory challenges to be overcome. One of the weak links in the operation of UAVs is the limited availability of energy. In order to address this issue authors developed a novel trajectory planning method for UAVs to optimize the energy necessity during flight. First, an “energy map” was created, which was the basis for trajectory planning, i.e., determining the energy consumption of the individual components. This was followed by configuring the 3D environment including partitioning of the work space (WS), in fact, defining the free spaces, occupied spaces (obstacles) and semi-occupied/free spaces. Then the corresponding graph-like path(s) were generated on the basis of the partitioned space, where a graph search-based heuristic trajectory planning was initiated, taking into account the most important wind conditions including velocity and direction. Finally, in order to test the theoretical results, some sample environments were created to test and analyse the proposed path generations. The method eventually proposed was able to determine the optimal path in terms of energy consumption.

Developments in artificial intelligence techniques allow for an improvement in sustainable mobility strategies with particular reference to energy consumption estimates of electric vehicles (EVs). This research proposes a vehicle energy model developed on the basis of Deep Neural Network (DNN) technology. The study also explores the potential application of the model developed for the movement data of new vehicles in the province of Enna, Sicily, Italy. which is characterized by numerous attractors and the increasing number of hybrid and electric cars circulating. The energy model for electric vehicles shows high accuracy and versatility, requiring vehicle velocity and acceleration as input data to predict energy consumption. The research article also provides recommendations for the energy modeling of electric vehicles and outlines additional steps for model development. The implemented methodological approach and its results can be used by transport decision makers to plan new transport policies in Italian cities aimed at optimizing vehicle charging infrastructure. They can also help vehicle users accurately estimate energy consumption, generate maps, and identify locations with the highest energy consumption.

The phenomena of light absorption, fluorescence and laser emission are accounted for within a unique picture. The atomic dipole is dealt with in a quantum framework, whereas the electromagnetic field is assumed to be a classical sine-wave. The on and off resonance cases are investigated. This is achieved owing to a novel application of Poynting's theorem. Observable predictions are made, regarding absorption of the electromagnetic energy and the frequency bandwidth of light emitted either by fluorescence or laser effect.

Cool roofs are roofing systems designed to reflect significant solar radiation, reducing heat absorption and subsequent cooling energy demands in buildings. This paper provides a comprehensive review of cool roof technologies, covering performance standards, material options, energy-saving potential, and hygrothermal considerations. The review examines provisions in current codes and standards, which specify minimum requirements for solar reflectance, thermal emittance, and solar reflectance index (SRI) values. These criteria often vary based on factors like roof slope, climate zone, and building type. Different cool roof materials are explored, including reflective paints and coatings that can be applied to existing roofs as cost-effective solutions. Several studies demonstrated the energy performance benefits of cool roofs, showing significant reductions in cooling loads, indoor air temperatures, peak cooling demand, and overall cooling energy consumption compared to traditional roofs. However, hygrothermal performance must be evaluated, especially in cold climates, to optimize insulation levels and avoid moisture accumulation risks, as reduced heat absorption can alter moisture migration patterns within the building envelope. While cool roofs provide substantial energy savings in hot climates, further research is needed to validate modeling approaches against real-world studies, investigate the impact of seasonality and green spaces on cool roof efficacy and urban heat island mitigation, and explore energy savings potential, moisture control, and condensation risks in cold and humid environments.

Abstract: A perspective is provided which illustrates the central role of quantum mechanics in the structure and periodically varying properties of atoms and in the formation of molecules. Despite having only about one hundred basic building blocks for all substances, chemistry is a subtle discipline due to it’s fundamentally quantum mechanical origin. The atoms, and their behavior as systematized in the Periodic Table, intimately reflect mechanisms natural to quantum mechanics but foreign to classical mechanics. Given their very small mass, the electrons form atomic structures only predictable by the use of quantum mechanics. Thereby the foundation of chemistry is totally dominated by quantum effects which are generally known only empirically, e.g. as in the Periodic Table. Recently these quantum effects have increasingly become known computationally, but not necessarily understood physically and therefore still challenge students and users of chemistry. In order to provide physical insight we extract here, from known facts and relations of quantum mechanics, but without reliance on detailed mathematics or numerical analysis, a simplest, yet fully consistent, physical explanation of atomic structure and periodically variable reactivity. Atomic reactivity is found to arise due to dynamical constraints on electron motion which lead to degeneracy in the atomic energy spectrum. There is a strong correlation between energy degeneracy and reactivity with the inert gas atoms found to display no degeneracy. Chemical bonding follows as a means of atomic reactivity relaxation and reduction of energy degeneracy, achieved by permanent electron rearrangement (ionic bonding) or by oscillatory electron motion between atoms (covalent bonding). Ionic bonding is directly related to the variable stability of atomic structures which extends from neutral atoms to atomic ions. These stable ions then form molecular structures by electrostatic attraction in neutral ionic clusters. The covalent bonding mechanism is fundamentally dynamical and interatomic since it depends directly on the facility with which electrons can move between atomic centers in a molecule. Both the ionic and the covalent mechanism, interatomic displacement and oscillation of electrons, are active in any bond between atoms of different species.

Defining integrals over volume element in curved spacetime together with the mass and energy densities within that region of spacetime is apparently equivalent to the given energy and mass of that body or particle. With this in mind equations involving energies and masses can be rewritten in terms of their densities and the integral over the curved space-time volume element. The idea find its place in quantum mechanical frameworks systematically accounting for the effect of spacetime volume structures and gravity on dynamics of quantum systems. This article briefly explores these concepts and runs through various frameworks and equations relevant to this idea including the quantum stress energy tensor, and expressing Schrodinger’s equation in ways that are tied to general relativity it also discusses the cosmological constant and the cosmological constant problem.

The present paper reports exact results for the muon self-energy and anomalous g-factor. A unique to the muon cut-off terms that remove the radial singularity in the system and regularize the corresponding electrodynamics are presented. Equations of motion and a transcendental equation satisfied by the muon anomalous g-factor are derived, with solution a_m=0.001165920162(198). The obtained value matches the latest experimental one found in the literature to about 0.43 ppb ruling out a possible tension between theory and experiment.

To control the volatility and reduce the electricity costs for indoor farming, the agrivoltaics agrotunnel introduced here uses: 1) high insulation for a building dedicated to vertical growing, 2) high-efficiency LED lighting, 3) heat pumps (HPs), and 4), solar photovoltaics (PV) provide known electric costs for 25 years. In order to size the PV array, this study develops a thermal model for agrotunnel load calculations and validates it using the Hourly Analysis Program and measured data so the effect of plants’ evapotranspiration can be included. HPs are sized, plug loads (i.e., water pump energy needed to provide for the hybrid aeroponics/hydroponics system, DC power running the LEDs hung on grow walls, and dehumidifier assisting in moisture condensation in summer) are measured/modeled. Ultimately, all models are combined to establish an annual load profile for an agrotunnel that is then used to model the necessary PV to power the system throughout the year. The results find that agrivoltaics to power an agrotunnel range from 40 to 50kW and make up an areas from 3.2 to 10.48 m²/m² of an agrotunnel footprint. Net zero agrotunnels are technically viable although future work is needed to deeply explore the economics of localized vertical food growing systems.

The article discusses issues related to the optimization of the operation of medium voltage networks, focusing on the optimization of network division points and the selection of the optimal network configuration aimed at reducing power and energy losses. The article provides a critical review of selected scientific works from recent years on the issue of network configuration optimization. The developed solution uses non-deterministic network models and statistical and probabilistic approaches. Optimization studies were carried out using heuristic optimization methods and proprietary algorithms for forecasting the load and power generated from renewable energy sources. The solution proposed in the article has many application possibilities. It can be used to optimize the location of network division points (reducing economic costs related to the modernization of network infrastructure) as well as to optimize the reconfiguration process in order to reduce power losses while maintaining voltage criteria.

Purpose. This paper aims to present a unique perspective that emphasizes the intricate interplay between energy, dietary proteins, and amino acid composition, underscoring their mutual dependence for health-related considerations. Energy and protein synthesis are fundamental to biological processes, crucial for the sustenance of life and growth of organisms. Methods and Results. We explore the intricate relationship between energy metabolism, protein synthesis, regulatory mechanisms, protein sources, amino acid availability, and autophagy, in order to elucidate how these elements collectively maintain cellular homeostasis. We underscore the vital role this dynamic interplay has in preserving cell life. Conclusion. A deeper understanding of the link between energy and protein synthesis is essential to comprehend fundamental cellular processes. This insight could have wide-ranging impact in several medical fields, such as nutrition, metabolism, and disease management.

This research paper aims to evaluate and model the performance of rice husk gasifier cook stoves for household energy use, a byproduct of rice milling. The study aims to address environmental issues and promote the use of rice husk as a renewable energy source and pest repellent in stoves. The study compared insulated and non-insulated gasifier stoves using rice husk gasification. The study compared the start-up time of insulated and non-insulated gasifier stoves, where the insulated stove showed a lower start-up time, but there was no significant difference at a 5% probability level. The temperature change also was not significant, as heat transfer and temperature change started when the husk was ignited. The burner stoves had different size and volume. The maximum operated or flame temperature was 1,190.30oC at room or minimum temperature of 27.33 oC, whereas the average temperature was 758.916oC for the non-insulated type of gasifier stove. The insulated gasifier stove also observed maximum and average temperatures of 518.30 oC and 289.014oC respectively at the same room temperature. The operating time of stoves directly influences the fuel consumption rate, specific gasification rate, and combustion zone rate of stoves. The fuel consumption rate has a significant effect on the type of gasifier stove, with the maximum rates being 3.820 and 2.099 kg/hr. The time to consume rice husks to gasify them depends on the density of the rice husk, reactor volume, and fuel consumption rate. The average specific gasification rate for insulated and non-insulated stoves is 106.45 and 120.63 kg/m2h, respectively. The fuel or rice husk holding capacity of each type of stove is significant at a 5% level, with the amount of rice husk and biochar produced being 1.18kg and 0.27kg for insulated stoves, and 2.511kg and 0.688kg for non-insulated stoves, respectively. The performance of gasifier stoves varies based on the bio char conversion rate, with non-insulated stoves producing a higher bio char mass per rice husk. Multiple regression analysis was used to model the relationship between time elapse with temperature and heat energy. The Squirrel-2020 data logger was used to measure the temperature produced by burning rice husks in the reactor of the stove as well as related generated and losses of heat. A relationship between the heat energy produced and the operating time of gasifier stoves was conducted to estimate the model. The cubic polynomial model was found to be the best predictive model fit for all variables of this study.

This research investigates the challenges and opportunities associated with supply chain transparency and traceability in the renewable energy sector. Using a qualitative methodology, the study involved semi-structured interviews with key stakeholders, including industry experts, supply chain managers, regulatory officials, and NGO representatives. The findings reveal that the complexity and global span of renewable energy supply chains pose significant hurdles for ensuring transparency and traceability. Variability in the maturity of traceability systems across companies further complicates the landscape, with some companies benefiting from advanced systems while others struggle with cost and technical barriers. Technological advancements, especially blockchain, offer promising solutions but require standardization and scalability to be effective. Regulatory frameworks play a crucial role, yet inconsistencies across jurisdictions create compliance challenges, underscoring the need for harmonized standards. Collaboration and partnerships are essential, providing platforms for sharing best practices and developing common standards. Enhanced transparency can lead to operational efficiencies, improved consumer trust, and stronger market positioning. Integrating sustainability into supply chain practices is fundamental, aligning with the increasing emphasis on ESG criteria among investors and stakeholders. Education and capacity-building, particularly for suppliers in developing countries, are vital for promoting transparency. Leadership and corporate culture are critical in driving these efforts, with strong commitment from the top necessary to implement effective practices. This study contributes valuable insights for stakeholders in the renewable energy sector, offering a foundation for future research and policy development aimed at advancing sustainable and ethical supply chain practices. The findings highlight the need for a holistic approach that integrates transparency and traceability into broader sustainability and business strategies.

The increasing deployment of intermittent renewable energy sources necessitates effective methods for balancing the electrical grid to ensure stability and safety. Energy storage systems that can store excess electrical power during periods of low demand and release it during high demand are crucial for both short-term and long-term applications. Power-to-Gas is an innovative energy storage solution that converts surplus renewable electricity into gas fuels, such as hydrogen, which can be stored and used later. This hydrogen can serve multiple purposes, including energy storage and as fuel for transportation modes like cars, trams, trains, and buses. While most hydrogen today is derived from fossil fuels, solid-oxide electrolysis (SOE) offers a cleaner alternative by producing hydrogen without harmful emissions. SOE is also the most efficient method of electrolysis. This study aims to determine the operational parameters for an SOE system, including lower heating value (LHV)-based efficiency and total input power, using a mathematical model. Results are presented for three different operating temperatures and four different steam utilization ratios. The paper is structured as follows: the introduction provides the context and motivation for the study; the second section outlines the fundamentals of electrolysis and its various types; the third section delves into solid-oxide electrolysis and electrolyser systems; the fourth section describes the methodology, including the mathematical formulation and simulation software used; the fifth section presents the calculation results and conclusions; and the final section summarizes the findings.

In this study is considered the design and implementation of pilots in desalination plants, in a systematic way, to evaluate energy improvements in water desalination processes. Pilot tests with the latest generation of reverse osmosis membranes in large desalination plants are becoming increasingly common, as small-scale experiments are carried out on the operation of new generation membranes with better salt rejection and lower energy consumption, to achieve the best water quality required for each case at the lowest possible cost. In this way, pilot tests are being carried out before the decision is made whether or not to change the reverse osmosis membranes, as this represents a significant investment and we minimize the risk of making a mistake in order to ensure the best results in terms of energy consumption, operating costs and reducing the environmental impact while complying with the required water quality. In this case, the Pareto analysis is used to highlight the 2 or 3 most significant causes whose treatment affects more than 80% of the possible energy improvement to be implemented. In this sense, figure 3 below shows the Pareto diagram for the energy improvement of N plants in a given territory. A series of factors that can affect this energy improvement have been numbered from 1 to 7, such as the seawater intake, the decision on the membranes, the energy recuperators, the high-pressure pump, the decisions on the pre-treatment, the feed pump or the post-treatment. The Pareto diagram has been studied at territorial level with a total of 180 seawater desalination plants. The novelty of this article is to apply Pareto diagram to a study of a total of 180 seawater desali-nation plants at territorial level in Canary Islands.

Solar energy has emerged as a promising alternative to traditional fossil fuels due to its abundant availability and sustainability. Solar cells, the fundamental units of solar energy conversion, have undergone significant advancements in fabrication techniques to enhance their efficiency, durability, and cost-effectiveness. This review aims to provide a comprehensive overview of various methods employed in the preparation of solar cells, including thin-film, crystalline silicon, organic, and perovskite-based technologies. By analyzing recent research developments, challenges, and future prospects, this article sheds light on the evolving landscape of solar cell fabrication, contributing to the ongoing efforts in achieving widespread adoption of solar energy.

Achieving Net Zero emissions target is driving up the need for offshore wind as an alternate energy source. Ireland has the capacity to produce upwards of 30GWof power through offshore wind alone. Wind resource assessments are extremely vital in determining the long term trends of a site. The instruments used for this often suffer breakdowns or miss readings which impacts the long term trend analysis. Wind time series data from Ireland’s Marine Institute is used which is shown to have significant gaps in it’s 20 years of service. Data imputation is necessary to fill in these gaps as accurately as possible. This paper compares LSTMs and ARIMA as two competing methodologies for data imputation. LSTMs are shown to be marginally superior to ARIMA imputation with a mean squared error of 0.45 compared to that of ARIMA of 0.60.

Ethiopian Airlines is a leading airline in the world. Its supply chain management is one of the most critical aspects in achieving its sustainability objectives. The present study aims to assess the sustainability practices and strategies of Ethiopian Airways in its supply chain, identifying areas for improvement and recommending strategies for enhancing sustainability. The study concentrates on pertinent sustainability concerns within the aviation sector while examining antecedent research on the sustainability of Ethiopian Airlines’ supply chain management strategies. The findings of the study reveal that there are several areas in need of improvement, including the implementation of waste reduction measures, the establishment of a recycling program, and the reduction of single-use plastic usage. It is suggested that promoting responsible tourism embodying sustainable practices is imperative, particularly within the airline context.

The magnesium ion is an essential cation in the human body and participates in numerous physiological activities. A deficiency in magnesium ions is closely associated with tumor development, and supplementation with magnesium ions has been shown to partially inhibit tumor growth. However, the specific mechanisms by which magnesium ions suppress tumor proliferation remain unclear. Currently, studies have revealed that mitochondria may serve as a crucial intermediate link in the regulation of tumors by magnesium ions. Mitochondria might intervene in the proliferation and invasion of tumor cells by modulating energy metabolism and oxidative stress levels. Therefore, this article provides a comprehensive review of the relationship between magnesium ions and tumors, the mechanisms by which magnesium ions regulate mitochondrial function, and the theoretical basis and prospects of magnesium ion regulation of mitochondrial function for tumor treatment. This review aims to offer insights for clinical tumor treatment strategies involving magnesium ion intervention.

The built environment sector’s growing impact on climate change is becoming increasingly important due to its share in energy consumption and greenhouse gas emissions. Global efforts have been undertaken to design and develop residential dwellings that aim towards zero energy and carbon emission, but there remains a multitude of obstructions to efficient construction processes. This study is focused on the gaps and barriers that have emerged during the pre-construction phase of a low-environmental-impact Passive House in Fayetteville, Arkansas. The technical, management, regulatory, and supply chain obstacles to the construction of a new three-story residential Passive House are documented to engage knowledge transformation in the design and construction of sustainable buildings of interest to developers and property owners. Primary data are collected by direct observation as well as open-ended interviews and secondary data collected through a literature review to understand the barriers and gaps faced by different key actors during the pre-construction phase in different regions. This local study highlighted the lack of interest, knowledge, and experience in sustainable building design among professionals having a significant influence on the project goals and timeline and was mentioned by participants as a common barrier as well as the inconsistency and inadequacy of regulatory framework of existing building codes to implement sustainable building design. These barriers along with other identified barriers are discussed and recommendations to overcome these barriers are provided.

Outliers seriously affect the accuracy in geometric model fitting. Previous works in coping with outliers involve threshold selection and scale estimation. However most scale estimators suppose the inlier distribution as a Gaussian model, which usually poorly meets the cases in geometric model fitting. Outliers, considered as the points with big residuals to all the true models, share common items with big values in quantized residual preferences, thus making the outliers gather away from the inliers in quantized residual preference space. In this paper we make use of this outlier consensus in quantized residual preference space by extending the usage of energy minimization to combine the model error and the spatial smoothness in quantized residual preference space for outlier detection. The energy minimization based outlier detection process follows an alternate sampling and labeling framework. After the outlier detection, an ordinary energy minimization method is employed to optimize the inlier labels, which also follows the framework of alternate sampling and labeling. The experimental results in this study show that the energy minimization based outlier detection method can detect most of the outliers in the data. Furthermore, the proposed energy minimization based inlier segmentation process segments the inliers into different models quite accurately. Overall, the performance of the proposed method is better than most of the state-of-the-art methods.

As a result of increased energy consumption, global trade has surged, and serious environmental problems have arisen. The problem is made more complicated by the fact that either environmental damage or economic advancement cannot be compromised. The elements contributing to environmental contamination must be identified and dealt with accordingly if we are to have a healthier future. In this study, what causes CO₂ emissions in Malaysia are examined using the Autoregressive distributed lag (ARDL) model using time series data from 1995 to 2020. The paper also examines the impact of energy use and economic complexity on CO2 emissions. Firstly, it is noted that the Environmental Kuznets Curve (EKC) theory holds in Malaysia. Furthermore, energy consumption has a detrimental impact on reducing CO2 emissions. Furthermore, it has been noted that a greater degree of economic complexity leads to an elevated amount of CO2 emissions over an extended period. The findings suggest significant environmental policy implications for reducing CO2 emissions in Malaysia.

The article presents a model for optimizing biomass supply chains using the linear programming framework integrated with a Geographic Information System. Based on the distance from a given type of biomass resource, its calorific value, price, and transportation costs, the model identifies the optimal source of biomass, allowing it to cover the demand for the required total energy value with the lowest possible costs. The case study includes the Połaniec power plant in southeastern Poland and potential sources of forest biomass and agricultural straw within 100 km of the plant. Unit costs of biomass varied depending on biomass availability and energy demands. For energy demand on the level of 1 PJ yearly, the lowest unit costs of biomass (4.08 €/MJ) were when all kinds of biomass were available, and the highest (5.47 €/MJ) was when only stacked wood was available. As energy demand increased, unit costs increased, and the ability to meet this demand with just one type of biomass decreased. The energy biomass sector can utilize the model to benefit both biomass producers and their final buyers.

Buildings consume 30% of the total energy consumption around the globe and 29% of the energy consumption in Egypt which in 2022 had a total population of 102 million, out of which 43 % live in urban areas . The operation of buildings contributes to around 30% of global CO2 emissions due to their high energy consumption (IEA, 2022a). Among the efforts made towards improving the energy efficiency of buildings are Advanced Energy Design Guides (AEDGs), building rating systems, codes, and standards. Furthermore, numerous research studies that are either literature review studies, experimental studies, or computational studies addressed the topic of energy efficiency in buildings. These are all examined in this literature review with the purpose of identifying the research gap in available research with a focus on Egypt. The identified gap is the development of a prescriptive path for the GPRS energy efficiency category based on whole building energy simulations.

The steep decline in the price of wind and solar photovoltaics provides a possibility to decarbonize electricity deeply and affordably. This study uses HOMER Pro energy modeling tool to model an optimized grid-connected renewable energy system for a community in southern Alberta, Canada. The study's goal is to identify the best renewable energy technology combinations that can provide electricity at the lowest levelized cost of energy (LCOE) and has lesser greenhouse gas emission as compared to the electricity produced by traditional fossil fuel. Gleichen, is a small town in southern Alberta and is near to numerous commercial wind and solar projects given the region’s high quality renewable resources. “Tri-brid” systems consisting of wind turbines, solar photovoltaics, and battery energy storage systems (BESS) are considered and compared based on electricity prices, net present cost, and greenhouse gas emissions savings. This tri-brid system is connected to the grid to sell excess electricity generated or buying electricity when there is less or no availability of solar and wind. The tri-brid energy system has an estimated LCOE of 0.0705 CAD/kWh which is competitive with the price of electricity generated by natural gas and coal which is 0.127 CAD/kWh.

A novel concept of a finned piston system is presented and analyzed where the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in direction of an isothermal process, reducing so the temperature of the compressed fluid in the compression chamber and reducing the necessary mechanical work for the process. The finned piston concept consists in an integrated heat exchanger inside of the chamber and being constituated of imbricated flat fins placed on the stator part and on the mobile piston. The internal heat exchange surface is strongly increased in comparison with a classical piston/cylinder. The energetic performance of the new system is evaluated with the help of simulation. Pressures, forces and temperature of the compressed gas are simulated as well as the mechanical work needed. The different curves are compared with adiabatic and isothermal characteristics.

Directive 2018/844/EU on energy efficiency claims almost 80% of final energy consumption in EU is used within the buildings. Subsequent Directive (EU) 2023/1791 introduced in 2023 expected 68% of the World population living in urban areas. Both Directives enhanced the role of energy management (EM) applied on the city buildings. The study introduces the development of energy management in Czech municipalities between the years 2009 and 2023. The main goal of this article is to present selected results of the unique national survey focused on the energy management in Czech municipalities conducted in 2023 and compare it with results of national surveys implemented in 2009 and 2018. The main method is the evaluation of deep survey conducted among the municipal representatives or energy managers in the past with the new survey conducted in 2023. The results show that EM became notably more important issue for the most Czech municipalities. The number of cities implementing EM significantly grew and the number of city energy managers increased too. On the other hand, the used potential of energy savings triggered by establishing EM is insufficient. This article should be applied to stress power of municipal EM in performing energy efficiency and RES projects and encouraging government to support municipal energy managers in their complex role.

Climate change has become a global nightmare, and the awareness of the causes of carbon emissions have resulted in rigorous studies. These studies linked the increase in global warming with booming economic growth. Since global warming has become more apparent, researchers have explored ways to decouple economic activities from carbon growth. Economic and carbon growth must be decoupled to achieve a low-carbon economy to support the carbon growth plan or emission reduction strategy. The world is transitioning towards a carbon-neutral and green ecosystem, so finding ways to decouple carbon emissions from economic activities is an exciting topic to explore. The study reviews current information on the importance of decoupling energy from economic growth innovative techniques that thoroughly examine the challenges and constraints of low-carbon energy systems. This review revealed that decarbonization and dematerialization had been achieved without declining global economic growth. It also provides information on energy use and economic activities leading to global carbon emissions and alternative solutions to the global challenge of climate change. The decoupling methods commonly used to determine the impact of energy decarbonization on economic growth are explored. All suggested that economic growth is a primary mover of global carbon emission increase and must be separated to achieve a carbon environment.

Time and space are fundamental concepts for characterizing and understanding our world. Despite of continuous curiosity and extensive studies, the nature of time and space remains elusive, and the underlying quantum structure is unclear. Here we propose a molecular model based on energy space decomposition to incorporate time and space synthetically in a unified framework. In the proposed model, the multipole expansion of action mapped to energy modules in scalar, vector, and matrix forms, results in the generators of time, space, and a material framework, cloud. And the invariance of time, space and cloud transformation corresponds to the conservation of energy, momentum, and mass, respectively. The classification of energy modules reveals a periodicity of energy elements, which constructs a hierarchical world in a molecular framework with dynamics represented by energy transformations. Here the role of time and space could switch from each other, and motion is attributed to the coupling of particle with intermediate bosons, corresponding to energy transformations among different energy modules. The application on Bohr model demonstrates that this picture provides a consistent classical interpretation to the foundation of quantum mechanics, and suggests an atomic model for gravitation.

Photovoltaic shading devices (PVSDs) have the dual function of providing shade and generating electricity, which can reduce building energy consumption and improve indoor daylighting levels. This study adopts a parametric performance design method and establishes a one-click simulation process by using the Grasshopper platform and Ladybugtools. The research focuses on the effect of dynamic PVSDs on daylighting and energy consumption in an office building in Qingdao. Through simulation, the study calculates the monthly energy consumption and useful daylight illuminance (UDI) under different inclination angles and installation heights of PVSDs. And the optimal configuration of PVSDs for each month under three dynamic strategies (rotation, sliding, and hybrid) is determined. Additionally, different control strategies and fixed PVSDs are compared to clarify the impact of various control strategies on daylighting and energy consumption. The findings reveal that, compared to no shading, dynamic PVSDs in rotation strategy (with an installation height of 0 m), sliding strategy (with an inclination angle of 20°), and hybrid strategy can achieve energy savings of 32.13%, 47.22%, and 50.38%, respectively. They can increase the annual average UDI by 1.39%, 2.8%, and 3.1%, respectively.

This study describes the synthesis, and characterization of lead-free organic ferroelectric perovskite N-methyl-N’-diazabicyclo[2.2.2]octonium)-ammonium trichloride (MDABCO-NH4Cl3). The electrospinning technique was employed to obtain nanofibers embedded with this perovskite into PVC polymer for hybrid fiber production. The dielectric, piezoelectric and pyroelectric properties of these fibers were carefully examined. From measurements of the dielectric permittivity temperature and frequency dependence, together with the pyroelectric results, a transition from a high temperature paraelectric to a ferroelectric phase that remained down to room temperature, was found to occur at 438 K. A pyroelectric coefficient as high as 290 C K-1 m-2value obtained is within the same order of magnitude as that reported for MDABCO-NH4I3 and the semiorganic ferroelectric triglycine sulfate (TGS). The hybrid nanofibers exhibited good morphological characteristics and demonstrated very good piezoelectric properties. Specifically, a piezoelectric coefficient of 42 pC/N was obtained when a periodical force of 3 N was applied. The performance of these fibers is on par with materials discussed in the existing literature for fabrication of nano energy harvesting generators. Importantly, the perovskite nanocrystals within the fibers not harmed by oxidation, making them a promising environmentally friendly platform for flexible energy harvesting.

This study conducts a comprehensive review of the integration of Hybrid Electric Turbochargers in mass-produced road vehicles. The primary objective is to inform the readers about the potential advantages and innovative applications of HETs. Employing a SWOT analysis, the research compares the performance of HETs on thermal engines versus traditional turbochargers and HETs on thermal engines versus HETs on hybrid engines based on a synthesis of multiple research findings. The study elucidates the fundamental mechanics of turbochargers, emphasizing their inherent benefits. Additionally, it introduces a novel approach with the integration of the hy-brid-electric turbocharger, demonstrating its capacity, supported by practical examples. The in-corporation of turbochargers with energy recovery mechanisms, including HETs, is shown to significantly contribute to emissions reduction. Moreover, the electric drive facilitates the utili-zation of hybrid turbines, particularly on low-displacement engines, resulting in enhanced effi-ciency, torque, and liter power. In conclusion, the research underscores the potential of HETs to substantially mitigate the environmental impact of the transportation sector by reducing emis-sions and conserving energy. Their ability to optimize the fuel efficiency and power output of internal combustion engines, coupled with the feasibility of downsized engines, positions HETs as an attractive option for both manufacturers and consumers. However, it is acknowledged that the implementation of HETs is in its early stages, necessitating further research to comprehensively understand their environmental impact. Despite this, the promising positive impact on the en-vironment designates HETs as a technology deserving close attention in the forthcoming years.

Solar energy adoption worldwide has expanded exponentially due to a surge in international interest in producing clean energy and the declining cost of solar power plants and their technology. It is anticipated that by 2050, solar will have surpassed fossil fuels to become the primary source of energy. However, one of the main challenges associated with solar energy production is the instability of photovoltaic (PV) power generation because of weather changes. Short-term forecasting of the power output of photovoltaic systems is essential for efficient management of the power grid and energy markets. This paper aims to evaluate the ability of deep learning (DL) models to provide accurate forecasting of hourly global horizontal irradiance (GHI) using different sets of features, including weather and aerosol variables along with solar radiation components. The results show that the best forecast skills are achieved by the long short-term memory autoencoder (LSTM-AE) model.

Floating wind is becoming an essential part in terms of renewable energy. Therefore, highlighting the perspectives in developing the floating wind platforms is very important. In this paper, we focus on floating wind concepts and projects around the world. This will give a taste to the reader about what is going on in terms of the projects around the world. The main aim of this work is to further explain the collected data regarding the floating wind concepts and projects, and further classify them in terms of cost, power capacity, wind speed, water depth, and distance to shore.

In the transition towards sustainable energy sources, hydrogen has emerged as the predominant alternative after fossil fuels. This comprehensive literature review delves into the evolving landscape of hydrogen launching strategies within the energy market. Numerous countries have strategically initiated efforts to introduce products based on hydrogen, underscoring the global acknowledgment of the potential inherent in hydrogen. Despite witnessing significant growth in the adoption of hydrogen energy worldwide, impediments to its widespread commercialization persist. This review identifies key barriers, including cost structures, technical complexities, and marketing challenges, hindering the establishment of a robust hydrogen energy market. The article critically examines the actions already undertaken to harness hydrogen energy for commercial purposes, leveraging scientific insights and statistical data. By carefully examining the current state of hydrogen energy initiatives, the review highlights gaps in existing strategies that require thoughtful consideration. Insights derived from scientific and statistical analyses inform the identification of barriers and contribute to a nuanced understanding of the challenges faced in the journey towards hydrogen energy commercialization. Ultimately, the article presents a strategic proposal outlining marketing actions geared towards expediting the commercialization and widespread adoption of hydrogen energy. Grounded in a thorough review of existing literature and supported by scientific and statistical evidence, this comprehensive analysis offers valuable insights for stakeholders seeking to navigate the intricate landscape of hydrogen energy in the global energy market.

Industry 4.0 brings advanced technologies and automation, enabling greater productivity and efficiency. However, it also increases energy consumption and carbon emissions. Sustainable manufacturing in the era of Industry 4.0 is vital for addressing the environmental impact by minimizing resource consumption, optimizing energy efficiency, and adopting eco-friendly practices. CNC (Computer Numeric Control) 5-axis milling plays a significant role in the machining of precision molds and dies, aerospace, consumer electronics, etc. This research aims to explore the potential of the artificial intelligence (AI) technique in improving energy efficiency on CNC 5-axis milling process for sustainable manufacturing. The experiments were carried out using a CNC 5-axis milling machine with various machining parameters, toolpath planning, and dry cutting condition. Data on energy consumption of CNC 5-axis milling machine were collected, then the relationship between the machining parameters, toolpath planning, and energy consumption was analyzed and built. Furthermore, an AI-based optimization algorithm was developed that uses machine learning and optimization techniques to identify energy-efficient machining strategies. The developed algorithm was implemented within a simulation framework, the algorithm was rigorously assessed using machine learning analysis to effectively reduce energy consumption, all while ensuring the accuracy of machining result. Finally, verification experiments were carried out to evaluate the applicability and performance of the AI-based energy optimization approach on a CNC 5-axis milling machine. By integrating AI into the CNC machining process, manufacturers can achieve significant energy savings, leading to reduced carbon emissions and improved sustainability.

AI applications are transforming the technology and digital sector, seamlessly integrating into the daily interactions of individuals with the digital world. Key entry points to the internet, such as search engines, are now complemented by recommendation systems that curate content on social networks, streaming platforms, and online marketplaces. Additionally, virtual assistants have become ubiquitous across various platforms. While these groundbreaking changes are gradually extending to several industries, there remains significant untapped potential for the application of artificial intelligence in diverse domains. The renewable energy sector, in particular, continually reinvents itself through research and innovation to meet the escalating demand. Positioned at the forefront of technological evolution, this industry is well-placed to effectively adopt and tailor the innovations of artificial intelligence to its specific needs. Presently, both emerging and established tools leverage elements of AI to enhance processes and introduce functionalities that were previously unattainable. If the current trajectory persists, AI-enhanced tools have the potential to assume a role as crucial to the future of engineering as computer-aided design (CAD) software is in contemporary times.

To facilitate wireless communication, ocean exploration, and various environmental and research applications, the underwater Internet of Things has been developed with an infrastructure of acoustic sensor networks. There has been a significant increase in failures and a decrease in the efficiency of the network due to the fluid and challenging underwater environment. Consequently, achieving quality of service (QoS) in underwater networks remains a research area. Supporting QoS in underwater sensor networks is challenging due to resource limitations such as processing power, memory, bandwidth, and power sources. The purpose of this study was to examine the service quality requirements as well as protocols that have been implemented in recent years. Finally, based on quality criteria, we have presented a routing solution based on fuzzy logic, which is more efficient than other recent methods regarding energy consumption rate, JFI, efficiency, and reliability.

The centrifugal force field in the hydrocyclone was affected by the concave-wall curvature radius R0, the mechanism of droplet deformation was closely related to the mass transfer efficiency. Numerical simulation and experimental data were collected to reveal the deformation characteristics and mechanism of single droplet crossing concave-wall jet. Normalized interfacial energy γ and stretching performance were provided to investigate the droplet deformation process. The results showed that the droplet was stretched along the streamwise and shrank along the spanwise in the concave-wall jet. The droplet interfacial energy and deformation were the largest when the droplet crossed the jet boundary at t = 0.20 s. Maximum γ value increased with the increase of R0 by 57.3% to 71.4%, and the distance between droplet and concave-wall increased with R0. Q-criterion was exported to show the vortex strength increasing as the decrease of R0 in the jet boundary. The pressure distribution inside the droplet showed that the pressure decreased as R0 increased, while the pressure difference increased along the streamwise and wall-normal direction. The study suggested that the droplet breakup was more difficult for the smaller R0, which was beneficial for liquid-liquid heterogeneous separation.

Background: Extremametly lean athletes could have difficulty for adaptive eating (intuitively or consciously) during ad libitum refeed. Aims: we verificate if there is a relation between adaptive eating and coping strategies with energy intake in a model of refeed proposed for bodybuilders. Methods: Fourteen male bodybuilders (29.6±3.1yrs; 85.6±6.8kg, ≥6 competitions) completed the 4-week each consisting of a 5 days of energy restriction following 2 days of refeed. Dietary assessment, body composition (ultrasound), Recovery stress questionnaire (REST-Q) and BRUMS (Brunel mood scale) were accessed pre and post; Coping Function Questionnaire (CFQ), Mindful Eating Scale version 2 (MES 2) and the Intuitive Eating Scale-2 (IES-2) was used at 4th week. Results: The refeed day resulted in a daily caloric increment of ~44% compared to the average energy intake on the energy restriction days, culminating in a weekly calorie deficit of ~27% and a drop in body mass of 3.1±1.4% with relation to initial values. The most reduced body fat and preserved or gained lean mass. The energy consumption during refeed maintained an inverse relationship with the perception of satiety (r=-0.9; p<0.01), total scores of IES 2 (r=-0.82; p<0.01), as well as with the confidence in hunger and satiety cues (r=-0.62; p=0.02) and congruence in food-body choice (r=-0.56; p=0.04) dimensions. Coping based in emotions maintained a relationship with the total scores of IES 2 (r=0.54; p<0.05) and an inverse relationship with energy intake during refeed (r=-0.42; p<0.05). Conclusion: Our results suggest that a higher perception of internal hunger and satiety signals and higher scores in intuitive eating may contribute to energy intake adequate, even when high scores of coping based in emotions are present.

Underground storage of natural gas has the characteristics of clean and low-carbon, and has the ability to provide sustainable and stable supply. It is a very high-quality green energy that can increase the storage efficiency of gas storage through fracturing, achieving the sustainable development goal of "Carbon Peaking and Carbon Neutrality". The accurate evaluation of the fracability of a reservoir is an important prerequisite for reservoir fracturing design and post fracturing productivity evaluation. At present, research on fracability is mainly based on qualitative characterization or quantitative evaluation based on rock mechanics and fracturing construction parameters, which cannot fully reflect the rock composition and structure of each stage. Firstly, based on logging data, this paper analyzes the evolution laws of strain energy such as elastic properties, pre-peak dissipation energy, and post-peak fracture energy during the transition of rock materials from plastic deformation to brittle fracture in an energy perspective, and determines the key energy that affects the brittle characteristics of rocks. Secondly, a brittleness index evaluation approach has been established that can comprehensively reflect the mechanical properties of rocks during pre-peak deformation and post-peak damage stages. In addition, this article focuses on the impact of reservoir stratigraphic environment by combining the influence of geo-stresses with the rock brittleness index, and proposes a new method for evaluating reservoir fracability. Finally, this paper conducts a study on the fracability evaluation of three wells in a gas storage facility in eastern China. The results indicate that low modulus and fracability coefficient are beneficial for fracturing, thereby improving the gas production and peak shaving ability of gas storage.

Internal combustion engine (ICE) vehicles contribute significantly to the global warming through their immense quantity of CO2 emissions and are on the way to be replaced by zero emission alternative solutions. Several replacement techniques with scientifically sound performances are proposed for the propulsion equipment including the related supply chains from renewable sources, but they often cannot fulfill the huge demand quantitatively. The paper discusses the quantitative aspects of the real demand with the example of the actual automotive park in Switzerland and analyses different alternatives like conventional EV’s, fuel-cell vehicles or energetic chains based on sustainable fuels like e-methanol or synthetic solar fuels. The analysis comprises energy efficiency considerations.

The creation of protonated water nanoclusters from amorphous water-ice under laboratory conditions suggests the possible ejection of such nanoclusters from ubiquitous amorphous water-ice-covered cosmic dust to interstellar space. The quantum properties of these quintessential water entities introduce a tantalizing prospect that bridges the origins of dark matter, dark energy, and life in the universe. The quantum-entangled diffuse Rydberg electronic states inherent to cosmic water nanoclusters make them plausible candidates for baryonic dark matter. Moreover, they exhibit the capacity to absorb, through the microscopic dynamical Casimir effect, virtual photons originating from zero-point-energy vacuum fluctuations occurring above the water-nanocluster vibrational frequency cutoff. This selective interaction leaves only vacuum fluctuations below these frequencies with gravitational significance, cancelling the vacuum-energy catastrophe and yielding a shared genesis for dark matter and dark energy. Moreover, this theory extends its implications to the origins of life itself, proposing that RNA protocells on Earth and habitable exoplanets may have emerged from the interactions between cosmic water nanoclusters and prebiotic organic molecules, thus yielding an anthropic narrative. Collectively, these findings coalesce into a cosmological framework depicting a cyclic universe, with cosmic water nanoclusters constituting a quintessence scalar field, instead of adhering to the multiverse concept based on cosmic inflation theory. Recent observations of CMB birefringence support this quintessence.

The layered oxyselenide BiCuSeO has garnered significant interest because of its ability to exhibit low thermal conductivity and a high Seebeck coefficient. This study involved the preparation of Bi1−xNaxCuSeO1−xFx(x=0, 0.05, 0.10, 0.15, and 0.20) ceramics through the processes of high energy ball milling and cold isostatic pressing. A systematic study was conducted to investigate the impact of co−doping Na/F on the thermoelectric performance of BiCuSeO ceramics. Replacing Bi3+ with Na+ results in the introduction of a considerable amount of holes, leading to a notable enhancement in the electrical conductivity and power factor. The conductivity was significantly increased from 9.10 S cm−1 in the pure BiCuSeO to 94.5 S cm−1 in Bi0.85Na0.15CuSeO0.85F0.15 at 323 K. At 823 K, the power factor of the Bi0.85Na0.15CuSeO0.85F0.15 sample achieved 44.8×10−5 W/ m K2. Moreover, the Bi1−xNaxCuSeO1−xFx ceramics exhibit a minimum thermal conductivity of 0.43 W m−1 K−1. As a result, the Bi0.85Na0.15CuSeO0.85F0.15 sample achieves a maximum ZT value of 0.78, which is 7.09 times greater than that of the pure BiCuSeO sample (0.11) .

This study examines the wind shear coefficient (WSC) values at three coastal wind sites located in the southern region of Balochistan, Pakistan: Pasni, Ormara, and Jiwani. These WSC values were obtained using 10-minute measured wind speed data at heights of 20, 40, and 60 meters above ground level (AGL). Since wind measurements are typically recorded at lower heights due to cost and resource constraints, extrapolation techniques were employed to estimate wind speeds at higher altitudes. However, using a constant WSC value for extrapolation may lead to significant errors between extrapolated and actual wind speed measurements, impacting the energy output of wind turbines. To evaluate the effect of WSC on energy yield, the study employed power curves and frequency distributions for 2MW and 1.5MW wind turbines. Additionally, wind power density was calculated using air density derived from measured air temperature and surface pressure data, covering two years period from November 2016 to August 2018. The overall mean WSC values were found to be 0.076 at Pasni, 0.094 at Jiwani, and 0.053 at Ormara. The study further investigated the seasonal, monthly, and diurnal variations of WSC. For assessing wind resources at a height of 60m, the study utilized Wind Roses, wind power density, and Weibull parameters. Comparing the actual WSC values presented in this paper with those obtained using the 1/7 power law and measured data at 60m AGL, the energy yield from the wind turbines showed reduced output and capacity factor.

Background: The proportion of dietary protein may play a key role in the development of obesity in children and adolescents. Methods: Cross-sectional data of 4,336 children and adolescents from the National Health and Nutrition Survey (NHANES) during 2011 to March 2020 were analyzed. Multivariate logistic regression analysis was used to estimate odds ratios (OR) and 95% confidence intervals, and restriction cubic spline was uesd to explore nonlinear relationships of dietary protein energy supply ratio and obesity in children and adolescents. Results:In the adjusted logistic regression model, for every 1% increase in dietary protein energy ratio in children and adolescents, the increased risk of obesity was 4% (OR=1.04,95%CI:1.01-1.08). The restrictive cubic spline showed a nonlinear relationship between dietary protein energy ratio and obesity in children aged 6-11 years (P <0.05). The dietary protein energy supply ratio was included in the logistic regression model after converting to quartiles into categorical variables. The adjusted OR of children aged 6-11 years was 2.08 (95%CI:1.34, 3.23,P <0.01) for the highest quartile of dietary protein energy supply ratio compared with the lowest quartile. Conclusion: In American children, dietary protein energy supply ratios was positively correlated with obesity, independent of individual characteristics and energy.