This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

The brittle shear failure of reinforced concrete beams is complexed and unfavorable. For decades, research on the mechanical properties and durability of recycled coarse aggregate (RCA) to make recycled aggregate concrete (RAC) has been widely investigated. However, test results on the shear strength of reinforced recycled aggregate concrete beams are still limited and contradictory. This paper reports the shear strength of reinforced recycled aggregate concrete beams without stirrups. Eight RAC beams and two controlled beams with natural coarse aggregate (NCA) were tested under the four-point flexural test with the shear span-to-effective depth ratio (a/d) of 3.10. Parameters in this study were the replacement percentage of RCA (0%, 25%, 50%, 75%, and 100%) and longitudinal reinforcement ratio (w) of 1.16% and 1.80%. It was found that the normalized shear stresses of RAC beams with w = 1.80% at all levels of replacement percentage were quite similar to that of the NAC counterparts. Normalized shear stress of the beam with 100% RCA and w = 1.16% was lower than that of the NAC beam by 5%. Database of 128 RAC beams without shear reinforcement from literature was analyzed to evaluate the ability of the most recent ACI 318-19 shear provisions in shear strength prediction. A reduction factor of 0.75 is proposed to the current ACI code provision to account for the physical variations of RCA such as replacement percentage, RCA source and quality, density, amount of residual mortar, and physical irregularity.

Water-soluble and cytocompatible polymers were investigated to enhance a transporting efficiency of biomolecules into cells in vitro. The polymers composed of 2-methacryloyloxyethyl phosphorylcholine (MPC) unit, a hydrophobic monomer unit, and a cationic monomer unit bearing an amino group were synthesized for complexation with model biomolecules, siRNA. The cationic MPC polymer was shown to interact with both siRNA and the cell membrane and was successively transported siRNA into cells. When introducing 20 − 50 mol% hydrophobic units into the cationic MPC polymer, transport of siRNA into cells. The MPC units (10 − 20 mol%) in the cationic MPC polymer were able to impart cytocompatibility, while maintaining interaction with siRNA and the cell membrane. The level of gene suppression of the siRNA/MPC polymer complex was evaluated in vitro and it was as the same level as that of a conventional siRNA transfection reagent, whereas its cytotoxicity was significantly lower. We concluded that these cytocompatible MPC polymers may be promising complexation reagent for introducing biomolecules into cells, with the potential to contribute to future fields of biotechnology, such as in vitro evaluation of gene functionality, and the production of engineered cells with biological functions.

To understand the mystery of final unification, in our earlier publications, we proposed that, 1) There exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions; and 2) There exists a strong interaction elementary charge (e_s) in such a way that, it's squared ratio with normal elementary charge is close to inverse of the strong coupling constant. In this context, starting from lepton rest masses to stellar masses, we have developed many interesting and workable relations. We noticed that, electroweak field seems to be operated by a primordial massive fermion of rest energy 585 GeV. It can be considered as the zygote of all elementary particles and galactic dark matter. Proceeding further, with a characteristic fermion-boson mass ratio of 2.27, quarks can be classified into quark fermions and quark bosons. Considering strong charge conservation and electromagnetic charge conservation, fractional charge quark fermions and quark bosons can be understood. Quark fermions that generate observable massive baryons can be called as Fluons. Quark bosons that generate observable mesons can be called as Bluons. By considering a new hadronic fermion of rest energy 103.4 GeV, rest masses of fluons and bluons can be estimated and there by baryon masses and meson masses can be estimated.

This study investigates the long-term impact of soil tillage systems and crop residue incorporation on agrophysical properties. A long-term field experiment has been conducted since 1999 at the Ex-perimental Station of Vytautas Magnus University Agriculture Academy. According to the latest edition of the International Soil Classification System, the soil in the experimental field was classified as Planosol, with a silty medium loam texture at a depth of 0–20 cm and a silty light loam at a depth of 20–40 cm. This investigation aimed to assess the long-term impact of reduced tillage systems, straw, and green manure combinations on soil physical properties, including soil shear strength, and soil aggregate stability. Studies were carried out on winter wheat crops in 2014, 2017, and 2023. The treatments were arranged using a split-plot design. In a two-factor field experiment, one part of the experimental field had straw removed, while the other part had the entire straw yield chopped and spread at harvest (Factor A). The subplot factor (Factor B) included three different tillage sys-tems: conventional deep ploughing, cover cropping for green manure with no-till, and no-tillage. Soil samples were analysed in the Laboratory of Agrobiology at Vytautas Magnus University Ag-riculture Academy. The findings indicate that long-term application of reduced tillage significantly increases soil shear strength. Shallower tillage depths lead to higher soil shear strength, while the effect of spreading plant residues is relatively lower. Long-term tillage of different intensities, spreading plant residues, and catch crop cultivation for green manure did not significantly affect soil structure. However, soil structural stability was found to be highly dependent on soil tillage. Cover cropping for green manure with no-till and no-tillage positively affected soil aggregate sta-bility in the upper (0–10 cm) and 10–25 cm layers.

The paper presents the influence of different curing conditions – wet, dry and protection against water evaporation on selected properties of concretes with different amount of recycled concrete aggregate previously subjected to atmospheric CO2 sequestration. Additionally, the eco-efficiency bi and ci indexes as well as eco-durability S-CO2 index were calculated. It was found that dry conditions deteriorate the properties of concrete, especially made of blast furnace slag cement, while protection against evaporation allows to achieve results comparable to wet conditions. Moreover, for series with the highest amount of coarse recycled aggregate and after longer period of curing, the difference between the effects of wet curing and protection against water evaporation disappears. The eco-efficiency and eco-durability indexes approach confirms the beneficial effect of blast-furnace slag cement used as a binder but on condition of proper way of curing.

Introduction: Flow-cytometry (FC) is a powerful tool that can assist in lymphoma diagnosis in lymph node (LN) specimens. Although lymphoma diagnosis and classification are mainly based on tumor cell characteristics, surrounding cells are less employed in this process.Methods: We retrospectively investigated alterations in the ploidy status, proliferative cell fraction (PF) and the percentages of surrounding immune cells in 62 consecutive LN specimens with B-Cell Non-Hodgkin Lymphoma (B-NHL) that were submitted for FC evaluation between 2019-2022.Results: Compared with indolent B-NHLs, aggressive B-NHLs show increased DNA aneuploidy and PF, increased monocytes, immature-granulocytes, mature granulocytes, CD8⁺ T-cells, Double-Negative-T-cells and Double-Positive-T-cells, and decreased total CD45⁺ cells, total lymphocytes, CD4⁺ T-cells and CD4/CD8 ratio. Receiver operating characteristic analysis determined PF > 6.8% and immature-granulocytes > 0.9% as optimal cutoffs with highest specificity and sensitivity in differentiating aggressive and indolent B-NHLs.Conclusions: These findings further strength the diagnostic value of DNA content analysis by FC and suggest the utilization of tumor surrounding immune cells in NHL diagnosis and classification.

Background: Thyroid nodules are common, affecting nearly 65% of the general population. While they are widespread, it's crucial to recognize that the majority of these nodules are not cancerous and can be effectively managed through careful monitoring. Thyroid ultrasound is commonly used to evaluate thyroid nodules owing to its low cost, wide availability and technical ease of application. In sonography, it's crucial to assess characteristics and vascular flow. Yet, conventional color and power Doppler ultrasound may not always effectively capture small vessels and low velocities due to their limitations. Superior Microvascular Imaging can display the blood flow of small vessels and low-velocity blood flow, which is difficult to visualize with conventional Doppler ultrasound. Meanwhile other thyroid scans, that utilize either [99mTc] pertechnetate or (18)F-fluorodeoxyglucose, can categorize nodules as hyperactive ('hot'), exhibiting normal activity ('warm'), or having reduced/no activity ('cold'). Thus, the main goal of screening and tracking thyroid nodules is to improve the management of potentially worrisome thyroid malignancies. Methodology: The study was conducted within the structural framework of a network meta-analysis, with the index tests being - SMI, Radionuclide Scanning and Color Doppler, and the general link between them being the reference gold standard. The data collection involved searching for all pertinent literature using PubMed, Google Scholar, and the Cochrane Library databases. The essential data was extracted following the application of specific inclusion and exclusion criteria.This meta-analysis included 7 RCTs with 1,152 patients for Radionuclide Scanning, 10 RCTs with 1,847 patients for SMI and 8 RCTs with 4,480 patients for Color Doppler. They were analyzed using the QualSyst tool and the risk of bias was evaluated by using QUADAS-2 analysis.The statistical software packages MetaDiSc 1.4, RevMan (Review Manager, version 5.3), SPSS (Statistical Package for the Social Sciences, version 20) and Excel in Stata 14 were used to perform the statistical analyses. Result: According to the findings, the sensitivity for Radionuclide Scanning is calculated as 0.79 (range: 0.76 to 0.81) and specificity as 0.55 (range: 0.50 to 0.60) with a 95% confidence interval. The overall diagnostic odds ratio (DOR) for Radionuclide Scanning Is 10.54.Additionally, with a 95% confidence interval, SMI exhibits a sensitivity of 0.82 (with a range of 0.79 to 0.84) and a specificity of 0.86 (with a range of 0.84 to 0.88), while the overall DOR is approximately 25.73. Color Doppler demonstrates a calculated sensitivity of 0.71 (ranging from 0.69 to 0.74) and specificity of 0.81 (ranging from 0.79 to 0.83) with a 95% confidence interval, while its DOR is 13.48.Conclusion: As evidenced by this meta-analysis, blood flow dependent imaging techniques are superior in their abilities to be used as diagnostic tests, especially in conjunction with their use in detecting thyroid nodules. This study offers a starting point for delving deeper into the utilization of Radionuclide Imaging, Superior Microvascular Imaging and Color Doppler in diagnosing thyroid nodules in a clinical setting. Key Words: - Thyroid Nodule, Radionuclide Scanning, Superior Microvascular Imaging, Color Doppler Diagnosis, Sensitivity, Specificity, Diagnostic imaging

Harnessing the Remarkable Bio-Remediation Potential of Vernonia spp. for the Sustainable Restoration of Hydrocarbon-Polluted Clay Soil in Ogoni Land, Nigeria This study explores the potential of utilizing Vernonia spp. for eco-friendly bio-remediation of hydrocarbon-polluted clay soil in Ogoni Land, Nigeria. The aim is to find a sustainable and effective solution that promotes the restoration of the polluted soil while minimizing the use of external additives. The process of bio-remediation can occur naturally, through natural attenuation or intrinsic bio-remediation. However, it has been observed that in certain cases, the addition of fertilizers, oxygen, or organic matter is required to enhance the effectiveness of bio-remediation. In this research, we focus on the bio-remediation potential of Vernonia spp., a native plant species known for its strong phytoremediation abilities. By harnessing the remarkable bio-remediation properties of Vernonia spp., we seek to restore the hydrocarbon-polluted clay soil in Ogoni Land in an environmentally friendly and sustainable manner. Our methodology involves conducting greenhouse experiments to assess the bio-remediation efficiency of Vernonia spp. in different soil conditions. We will analyze the soil's physical and chemical properties, as well as the degradation of hydrocarbons over time. The experimental results will provide valuable insights into the effectiveness of Vernonia spp. in removing hydrocarbon pollutants from clay soil. Through this study, we aim to develop a cost-effective and sustainable approach to restore hydrocarbon-polluted clay soil in Ogoni Land. By leveraging the natural bio-remediation potential of Vernonia spp., we can potentially reduce the reliance on external additives, thus minimizing the environmental impact associated with traditional remediation methods. The research article explores methods to promote the growth of pollution-eating microbes in order to enhance bio-remediation. Bio-remediation refers to the use of naturally occurring organisms to break down harmful substances into less toxic or non-toxic forms. In situ bio-remediation involves treating the contaminated material directly at the site, while ex-situ bio-remediation involves removing the contaminated material for treatment elsewhere. This study specifically investigates ex-situ bio-remediation techniques for hydrocarbon-contaminated clay soil. The researchers found that the application of room dry and wet blended bitter leaf showed promising results in the bio-remediation of hydrocarbons in the clay soil. Using Vernonia galamensis, a concentration as high as 0.55 ug/ml was achieved, while Vernonia amygdalina yielded a concentration as high as 0.67 ug/ml when applied at 35g and 40g respectively, based on the wet blended approach. These findings highlight the effectiveness of wet blended Vernonia species in the bio-remediation process.During the remediation process of the clay soil, the pH levels showed a trend of increasing from acidic to normal to alkaline. This can be attributed to the remediation of excessive metals present in the soil. After 40 days, the pH of the clay soil reached 6.97 when treated with 40 grams of Vernonia galamensis, and 7.00 when treated with 40 grams of Vernonia amygdalina. Interestingly, while the remediation efficiency of HC (hydrocarbon) decreased with increasing mass of Vernonia galamensis, the remediation efficiency of HC increased when using Vernonia amygdalina. These observations highlight the varying effects of different Vernonia species on hydrocarbon remediation.The highest remediation values were observed when using Vernonia galamensis at 35g and Vernonia amygdalina at 40g. These particular amounts of these Vernonia species demonstrated effective remediation of the targeted pollutants. However, in comparison to other metals, the remediation effects were relatively lower for zinc (Zn), with only approximately 0.25 ug/ml being remediated. This suggests that the remediation potential of the Vernonia species may vary depending on the specific contaminant.The higher remediation effects observed for Zn metal in the soil can be attributed to the wet blended preparation method of the Vernonia species. In contrast, the room dried Vernonia species exhibited the lowest performance in remediating the soil, with approximately 0.17 ug/ml and 0.10 ug/ml remediation for galamensis and amygdalina, respectively. Both Vernonia leaf extracts achieved a remediation of 0.5 ug/ml for chromium. The sun dried and room dried methods also showed considerable remediation potential, with values above 0.4 ug/ml. The level of significance for the model was attained at 0.05, and the r2 value was appreciable. These findings indicate the effectiveness of different preparation methods and Vernonia species in soil remediation

With reference to our earlier published views on large nuclear gravitational constant , nuclear elementary charge and strong coupling constant , in this paper, we present simple relations for nuclear stability range, binding energy of isotopes and magic proton numbers.

High-quality optical Fano resonances, which exist in a spherical dielectric microparticle in the spatial configurations of the "whispering-gallery modes" (WGMs) and recently are referred to as the “super-resonances”, possess extremal sensitivity not only to the micro-cavity size and shape but also to the optical properties of the particulate material. The increase in the power of light radiation coupling into a super-resonance can lead to the manifestation of strong optical nonlinearity of the resonator material due to the cubic nonlinearity (optical Kerr effect) and generation of free electron plasma in certain regions of the spherical microcavity. In fact, an optically linear medium of the resonance cavity transforms into a Drude-Kerr-type medium with a strong dependence on input laser intensity. With the help of the finite-elements numerical simulations, we theoretically analyze the transformations of the resonant contour for a number of high-quality WGMs excited in a lanthanum-glass microsphere exposed to an optical radiation of different intensity. We show that in a certain input intensity range, the competition of Kerr and plasma optical nonlinearities can stop and even reverse the Stokes shift of the super-resonance observed in a pure Kerr medium. Additionally, optical ionization and plasma generation within the mode volume significantly reduce the strength of the magnetic super-resonance and lead to its spoiling and frequency splitting.

Current artificial intelligence (AI) technology is still considered weak AI. However, the progression towards strong AI unavoidably involves grappling with concerns surrounding consciousness, the mind, and creativity. This paper focuses on analyzing consciousness, creativity, and the generation of emotions to explore the possibility of machine-based consciousness, creativity, and emotion. We believe that the emergence of consciousness relies on the complex interplay at different layers within a complex system, rather than wholly relying on the underlying substrates of the system. Thus, it is plausible to consider the existence of machine-based consciousness, creativity, and emotion. Furthermore, swarm intelligence should be recognized as a distinct form of intelligence. Human individuals serve as the foundational substrate enabling the realization of swarm intelligence, with individual intelligence reflecting the projection of swarm intelligence at the individual level. The advanced state of human civilization is primarily attributable to the effect of swarm intelligence. Building upon basic emotions to adapt to environmental conditions, advanced human emotions are a product of the evolutionary process by swarm intelligence. Emotions serve as a pivotal impetus for the formation and development of societies grounded in swarm intelligence. In pursuit of super-AI that surpasses human civilization in the future, nurturing swarm intelligence represents an inevitable trajectory.

The overcrowding of high-rise buildings in the city adversely affects the wind environment by changing the air currents in the surrounding areas. In particular, extreme climate phenomena caused by climate change are stronger and more frequent, causing social damages in cities. To comprehensively better understand the wind properties around high-rise buildings, actual filed measurement is necessary to determine the environment assessment of wind effect. We performed the on-site measurement on LCT residential complex regions (411.6m tall) with highly concentrated high-rise buildings in coastal city Busan, South Korea under extreme weather conditions such as typhoon invasions to determine wind fluid characteristics. In the field monitoring, five anemometers were installed to analyze the wind environment around high-rise buildings when typhoon 'Hinnamnor' invaded. Compared to the nearby weather station operated by KMA(Korea Meteorological Administration), the gust was 3.7 times stronger and the max 1 min-mean wind speed was 3.1 times stronger, and the characteristics of the downward wind and the canyon wind were shown depending on the location characteristics of the point. Turbulence intensity decreased as the wind speed increased and converged to a certain value. Likewise, the gust factor also decreased as the wind speed increased and converged to 2.0, which is considered to be the parameter that best represents the intensity of the instantaneous gust caused by the skyscraper wind effect.

BackgroundLiving donor liver transplantation offers comparable long-term results to cadaveric donor transplantation. This study analyzes the selection process of living liver donors at a Western transplant center that utilizes both donation forms. MethodsThis retrospective analysis examined potential living donors, collecting medical data and reasons for refusal, and divided patients by indication and urgency for transplantation. ResultsFrom January 2013 to December 2023, 594 potential living donors were assessed at Jena University Hospital. Of these, 124 living donor transplants were performed. During outpatient evaluation, 357 potential donors were excluded. Subsequently, 238 individuals underwent inpatient assessment, with 100 more being excluded. Main reasons for donor refusal included medical or psychological issues (n=160), disease progression in recipients (n=90), and recipient refusal or donor withdrawal (n=54). The evaluation process showed a trend towards considering more distant relatives and acquaintances as donor candidates with increasing severity of the recipient's disease.

This article describes a novel electrochemical on-chip biosensor that utilizes anti-PSA antibody (Ab) and silver nanoparticles (AgNPs) to enhance the sensing and detection capability of prostate specific antigen (PSA) in the blood. The AgNPs are prepared, characterized, and applied onto a silicon photonic on-chip biosensing receptor platform designed to enhance the accurate detection of PSA. The AgNPs were synthesized by a chemical reduction method using silver nitrate (AgNO₃) as the precursor. Transmission electron microscopy (TEM), selected area electron diffraction (SAED), energy dispersion X-ray spectroscopy (EDS), small angle X-ray scattering (SAXS), X-ray diffraction (XRD), and light microscopy were among the methods used in the characterization and analysis of the AgNPs. Each stage of the immunosensor fabrication was characterized using cyclic voltammetry. The proposed immunosensor was applied in the detection of PSA, a prostate cancer biomarker, with a high sensitivity and a limit of detection of 0.17 ng/mL over a linear concentration range of 2.5 to 11.0 ng/mL. The immunosensor displayed good stability and was selective in the presence of interfering species like immunoglobulin (Ig) in human serum, ascorbic acid (AA), and diclofenac (Dic). The detectivity and sensitivity are significantly higher than previous reports on similar or related technologies.

Plant biomass could become a new world-class "currency" because almost everything can be made of it: fuels, foods, feeds, constructing materials, furniture, etc. Currently, growing biomass for energy needs is particularly relevant in so complicated socioeconomical situation. There are important its productivity and the lowest possible ecological footprint. Can increasing crop biodiversity address these challenges? A field experiment was started at the Vytautas Magnus University Agricultural Academy in 2020-2022. Maize, hemp and faba bean were grown as single, binary and ternary crops to determine its effect on soil properties. Studies have shown that most intercrops failed to stabilize soil aggregate composition, NPK levels and pH, and enzyme urease activity. Binary maize-hemp and the ternary crops reduced the amount of the main macroelements in the soil the most because of the highest yields, which were removed from the fields. Regardless of the ecological services provided by faba beans, biomass removal leads to degradation of most soil properties and making the soil vulnerable to erosion. In the future, the cultivation of such multicrops should be investigated under conditions of more abundant fertilization or the effect of green manure should be used by increasing the number of fast- and short-growing interior plant species in the cultivation.

This study aimed to compare the differences in durability and prestress loss between normal-weight concrete (NC) and lightweight aggregate concrete (LWC) prestressed box girders, which were constructed at the same time in the same area, so as to verify the superiority of using synthetic lightweight aggregate (LWA) made from reservoir sediments in prestressed bridges. For the NCs and LWCs used in prestressed box girders, the basic mechanical properties were tested on the one hand, and the durability properties were tested on the other hand. Then, through the prestress monitoring system, the prestress loss of the two groups of the prestressed box girders was tracked. The results of the durability test confirmed that LWC can inhibit the penetration of air, water, and chloride ions by strengthening the interfacial transition zone between the aggregate and the cement paste, thereby improving its durability. Moreover, the magnetic flux prestress loss of the NC prestressed box girder reached 8.1%. In contrast, the magnetic flux prestress losses on both sides of the LWC prestressed box girder were 4.6% and 4.9%, respectively. This verified that, under the same environmental conditions, the use of LWC produced less of a prestress loss than the use of NC.

Current stock market forecasting methods encompass fundamental, technical, emotional, and bargaining factors. Predominantly, price prediction hinges on order volume and price, although correlating these two within existing models proves challenging. This study employs Cycle Generative Adversarial Network (Cycle GAN) to unravel the intricate price-volume relationship, combining it with Bollinger Bands for trading signal analysis, overcoming hurdles in short-term forecasting prevalent in numerical analysis and AI. Focusing on TSMC (2330.TW) stock price, the research leverages Cycle GAN in deep learning to master the price-volume nexus, juxtaposed with LSTM and RNN. Historical TSMC closing prices and transaction counts are model inputs, scrutinizing their interconnectedness for predictions. This innovative approach aligns stock price, volume, market value, taxes, and prior changes via system engineering. By intertwining Bollinger Bands with stock price forecasts, trading signals are distilled, factoring in extended index %b for a comprehensive market picture.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

Flaviviruses replicate in membranous factories associated with the endoplasmic reticulum (ER). Significant levels of flavivirus polyprotein integration contribute to ER stress and the host cell may exhibit an Unfolded Protein Response (UPR) to this protein accumulation, stimulating appropriate cellular responses such as adaptation, autophagy or cell death. These different stress responses support other antiviral strategies initiated by infected cells and can help to overcome viral infection. In epithelial A549 cells, a model currently used to study the flavivirus infection cycle and the host cell responses, all three pathways leading to UPR are activated during infection by Dengue virus (DENV), Yellow Fever virus (YFV) or West Nile virus (WNV). In the present study, we investigated the capacity of ZIKA virus (ZIKV) to induce ER stress in A549 cells. We observed that the cells respond to ZIKV infection by implementing an UPR through activation of the IRE1 and PERK pathway without activation of the ATF6 branch. By modulating the ER stress response, we found that UPR inducers significantly inhibit ZIKV replication. Interestingly, our findings provide evidence that ZIKV could manipulate the UPR to escape this host cell defence system. Since incomplete UPR could lead to unresolved and persistent ER stress, we found that ZIKV infection was associated with an abnormal accumulation of viral envelope proteins, which were aggregated with non-native disulfide bridges. As the presence of these “amyloid like” protein polymers may be cytopathic, our observations provide new insights into specific neuropathologies associated with ZIKA virus infections.

Electric arc furnace oxidizing slag (EAF) has a high density of 3.0~3.7 t/m3 and therefore has a high bulk density when mixed with concrete. Extensive research has been conducted on the use of concrete with high unit volume weight as heavyweight concrete for radiation shielding concrete. In this study, to examine the possibility of developing a radiation shielding concrete, the physical properties of normal concrete, magnetite concrete, EAF concrete, and EAF concrete with added iron powder, were compared. Also, their radiation shielding performance was assessed through shielding tests against X-rays and γ-rays. While the unit volume weight of EAF concrete (3.21 t/m3) appeared lower than that of magnetite concrete (3.5 t/m3), the compressive strength of EAF concrete was greater than those of magnetite and normal concretes. The radiation shielding ratio of magnetite concrete was observed to be 93.9% from the X-ray shielding test, followed by 91.2% of EAF concrete, and 73.7% of normal concrete, indicating a linear relationship with unit volume weight. From the γ-ray shielding test, the performance of EAF and magnetite concretes appeared to be similar. Based on the excellent physical properties and radiation shielding performance of EAF concrete, its potential applicability as radiation shielding concrete was confirmed.

Hox gene clusters are crucial in Embryogenesis. It was observed that some Hox genes are located in order along the telomeric to centromeric direction of the DNA sequence: Hox1, Hox2, Hox3…. These genes are expressed in the same order in the ontogenetic units of the Drosophila embryo along the Anterior-Posterior axis. The two entities (genome and embryo) differ significantly in linear size and in-between distance. This strange phenomenon was named Spatial Collinearity (SP). Later, it was observed that, particularly in the Vertebrates, a Temporal Collinearity (TC) coexists: first is Hox1 expressed, later Hox2 and even later Hox3,…,. According to a Biophysical Model (BM), pulling forces act at the anterior end of the cluster while a cluster fastening applies at the posterior end. Hox clusters are irreversibly elongated along the force direction. During Evolution, the elongated Hox clusters are broken at variable lengths thus split clusters may be created. An Empirical Rule was formulated distinguishing development due to a complete Hox cluster from development due to split Hox clusters. BM can ‘explain’ this Empirical Rule. In a spontaneous mutation where the cluster fastening is dismantled, a weak pulling force automatically shifts the cluster inside the Hox activation domain. This cluster translocation can probably explain the absence of Temporal Collinearity in Drosophila.

The inherited ‘EIA’ process at Brexit is based on a ‘Project’ period from Inception tothe start of construction works. The ‘Incompleteness’ of the process covers andidentifies stages that will impact on the environmental cycle: construction period,operational life, de-commissioning and a return to acceptable environmental footprint.A master environment structure-plan framework is required to commence with theupgrading of the complete ‘EIA’ process, embracing separate limbs for the UK’spriority environmental targets for climate change, and other major adverse effectswhich result in serious ‘harm’ to the UK environment. The identification of the processfor ‘incompleteness’ requires effective sustainability, and inclusion of effectivemanagement tools, for the essential ‘monitoring/control/recording’ proceduresthroughout the project life and the natural environmental cycle. This will allow theopportunity for a new approach to a structured ‘Suite of EIAR Directives’, to enable a‘EIAR’ regime that ‘will remain fit and proper for UK purpose’.

Here we analyze three well-known conjectures: (i) the existence of infinitely-many twin primes, (ii) Goldbach’s strong conjecture, and (iii) Polignac’s conjecture. We show that the three conjectures are related to each other. In particular, we see that in analysing the validity of the Goldbach’s strong conjecture, one must consider also the existence of an infinite number of twin primes. As a consequence of how we approach this analysis, we also observe that if this conjecture is true, then so is Polignac’s conjecture. Our first step is an analysis of the existence of infinitely-many twin primes numbers. For this, using the formula 4((n−1)!+1) ≡ −n (mod n(n + 2)) – satisfied if and only if (n, n + 2) are twin primes –, together with Wilson’s theorem, we obtain conditions that must be met for two numbers to be twin primes. Our results, obtained from an analytic and functional study, lead us to conclude that there may exist infinitely-many twin primes. Next, we consider the validity of the Goldbach’s strong conjecture. After showing that the conjecture is true for the first even numbers, we notice a pattern that we analyze for any even number, reducing it to three cases: (i) when the even number 2n is two times a prime number n; (ii) when the even number 2n is such that n = 2m, with 2m − 1 and 2m + 1 twin primes; (iii) all other cases, i.e., for any 2n even number ∀n ∈ N with n > 1, n prime or not, with independence of n = 2m being 2m−1 and 2m+1 twin primes or not. In this last case we show that one can always find a certain r ∈ N such that 1 < r < n satisfying that n−r and n+r are primes, so that their sum is 2n. In this case we use the reduction to absurd method, and our results lead us to conclude that Goldbach’s strong conjecture is true to the best of our calculations, as well as the Polignac’s conjecture.

We construct a repeated quantum game with public goods by the quantum entanglement and strong reciprocity. By using the paradigm of quantum game analysis, we obtain that both the quantum entanglement and strong reciprocity are helpful to intensify cooperation and achieving Pareto optimality. In addition, under an example which is greenhouse green viable planting industry, we verify that the quantum entanglement and strong reciprocity have a positive role in cooperation.

A physical scrutiny of experimental results published in Physical Review Letters (December 2015, M. Giustina, et al., Phys. Rev. Lett. 115, 250401, and L. K. Shalm et al., Phys. Rev. Lett. 115, 250402) is undertaken. These articles reported that measured outcomes were fitted with quantum states possessing a dominant component of non-entangled photons, thereby contradicting their own claim of quantum nonlocality. With probabilities of photon detections lower than 0.1 %, the alleged quantum nonlocality cannot be classified as a resource for developing quantum computing devices, despite recent publicity. Experimental evidence of a feasible process for quantum-strong correlations has been identified (M. Iannuzzi, et al., Phys. Lett. A, 384 (9), 126200, 2020) in terms of correlations between independent and multi-photon states evaluated as Stokes vectors on the Poincaré sphere. As single-photon sources are not needed, the design and implementation of quantum computing operations will be significantly streamlined.

Physics of high-Tc superconducting cuprates is obscured by the effect of strong electronic correlations. One way to overcome the problem is to seek for an exact solution at least within the small cluster and expand it to the whole crystal. Such an approach is in the heart of the cluster perturbation theory (CPT). Here we develop CPT for the dynamic charge and spin susceptibilities (spin-CPT), within which the correlation effects are explicitly taken into account by the exact diagonalization. We apply spin-CPT to the effective two-band Hubbard model for the cuprates obtained from the three-band Emery model and calculate one- and two-particle correlation functions, namely, spectral function and spin and charge susceptibilities. Doping dependence of the spin susceptibility was studied within spin-CPT and CPT-RPA that is the CPT generalization of the random phase approximation (RPA). Both methods produce the low energy response at four incommensurate wave vectors in qualitative agreement to the results of the inelastic neutron scattering on overdoped cuprates.

New setting is introduced to study the global powerful alliance. Global powerful alliance is about a set of vertices which are applied into the setting of neutrosophic graphs. Neighborhood has the key role to define this notion. Also, neighborhood is defined based on strong edges. Strong edge gets a framework as neighborhood and after that, too close vertices have key role to define global powerful alliance based on strong edges. The structure of set is studied and general results are obtained. Also, some classes of neutrosophic graphs excluding empty, path, star, and wheel and containing complete, cycle and r-regular-strong are investigated in the terms of set, minimal set, number, and neutrosophic number. Neutrosophic number is used in this way. It’s applied to use the type of neutrosophic number in the way that, three values of a vertex are used and they’ve same share to construct this number. It’s called “modified neutrosophic number”. Summation of three values of vertex makes one number and applying it to a set makes neutrosophic number of set. This approach facilitates identifying minimal set and optimal set which forms minimal-global-powerful-alliance number and minimal-global-powerful-alliance-neutrosophic number. Two different types of sets namely global-powerful alliance and minimal-global-powerful alliance are defined. Global-powerful alliance identifies the sets in general vision but minimal-global-powerful alliance takes focus on the sets which deleting a vertex is impossible. Minimal-global-powerful-alliance number is about minimum cardinality amid the cardinalities of all minimal-global-powerful alliances in a given neutrosophic graph. New notions are applied in the settings both individual and family. Family of neutrosophic graphs has an open avenue, in the way that, the family only contains same classes of neutrosophic graphs. The results are about minimal-global-powerful alliance, minimal-global-powerful-alliance number and its corresponded sets, minimal-global-powerful-alliance-neutrosophic number and its corresponded sets, and characterizing all minimal-global-powerful alliances, minimal-t-powerful alliance, minimal-t-powerful-alliance number and its corresponded sets, minimal-t-powerful-alliance-neutrosophic number and its corresponded sets, and characterizing all minimal-t-powerful alliances. The connections amid t-powerful-alliances are obtained. The number of connected components has some relations with this new concept and it gets some results. Some classes of neutrosophic graphs behave differently when the parity of vertices are different and in this case, cycle, and complete illustrate these behaviors. Two applications concerning complete model as individual and family, under the titles of time table and scheduling conclude the results and they give more clarifications and closing remarks. In this study, there’s an open way to extend these results into the family of these classes of neutrosophic graphs. The family of neutrosophic graphs aren’t study deeply and with more results but it seems that analogous results are determined. Slight progress is obtained in the family of these models but there are open avenues to study family of other models as same models and different models. There’s a question. How can be related to each other, two sets partitioning the vertex set of a graph? The ideas of neighborhood and neighbors based on strong edges illustrate open way to get results. A set is global powerful alliance when two sets partitioning vertex set have uniform structure. All members of set have more amount of neighbors in the set than out of set and reversely for non-members of set with less members in the way that the set is simultaneously t-offensive and(t-2)-defensive. A set is global if t=0. It leads us to the notion of global powerful alliance. Different edges make different neighborhoods but it’s used one style edge titled strong edge. These notions are applied into neutrosophic graphs as individuals and family of them. Independent set as an alliance is a special set which has no neighbor inside and it implies some drawbacks for these notions. Finding special sets which are well-known, is an open way to purse this study. Special set which its members have only one neighbor inside, characterize the connected components where the cardinality of its complement is the number of connected components. Some problems are proposed to pursue this study. Basic familiarities with graph theory and neutrosophic graph theory are proposed for this article.

Starting from the model of a slow-rolling missile with six degrees of freedom (6 DOF) in the body frame, a 6 DOF model in the Resal frame is obtained, which is used to linearize the coupled commanded motion. Based on the linearized model, we obtain the structural scheme of the commanded object and define the quality parameters. The obtained parameters have a complex representation (with real and imaginary parts) due to the coupling between longitudinal channels. Then, the kinematic guidance equations, the seeker equations and the actuator specific to the slow-rolling single-channel missile are defined using a switching function. The guidance kinematic equations, the seeker equations and the actuator model are linearized in the Resal frame, and the structural diagram of the homing missile is constructed. Starting from this, the characteristic polynomial having complex coefficients is determined and then analyzed with the Frank-Wall stability criterion. Based on the analysis, a stability range is determined for the navigation constant and a minimum and possibly a maximum limit for the time to hit the target is obtained. The stability range defined for the navigation constant on the linear model is finally validated on the nonlinear model in the body frame.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

Transient receptor potential melastatin-8 (TRPM8) is a cation channel that is activated by cold and “cooling agents” such as menthol and icilin, which induce a cold sensation. Stimulation of TRPM8 activates an intracellular signaling cascade that ultimately leads to a change in the gene expression pattern of the cells. Here, we investigated the TRPM8-induced signaling pathway that links TRPM8 channel activation to gene transcription. Using a pharmacological approach, we show that inhibition of phosphatidylinositol 4-phosphate 5 kinase alpha (PIP5K), an enzyme essential for the biosynthesis of phosphatidylinositol 4,5-bisphosphate, attenuated TRPM8-induced gene transcription. Analyzing the link between TRPM8 and Gq proteins, we show that pharmacological inhibition of the beta gamma subunits impairs TRPM8 signaling. In addition, genetic studies showed that TRPM8 requires an activated Galpha subunit for signaling. In the nucleus, the TRPM8-induced signaling cascade triggers an activation of the transcription factor AP-1, a complex consisting of a dimer of basic region leucine zipper (bZIP) transcription factors. Here, we identified the bZIP protein c-Jun as an essential component of AP-1 within the TRPM8-induced signling cscade. In summary, with PIP5K, Gq subunits and c-Jun we have identified key molecules in the TRPM8-induced signaling from the plasma membrane to the nucleus.

The 2022-2023 Mpox multi-country outbreak, identified in over 110 WHO Member States, revealed a predominant impact on cisgender men, particularly those engaging in sex with men, while less frequently affecting women. This disparity prompted a focused investigation into the gender-specific characteristics of Mpox infections, particularly among women, to address a notable knowledge gap. This review systematically gathers and analyzes scientific literature and case reports concerning Mpox infections in women, covering a broad geographical spectrum including regions such as Buenos Aires, Brazil, Northern California, Colombia, Nigeria, Europe, Vietnam, Spain, Switzerland, and the United States. The analysis delves into various aspects of Mpox in women, including clinical features, epidemiology, psychological impacts, preparedness strategies, and case studies, with particular attention to pregnant women and those with underlying health conditions. Empirical data from multiple studies underscore the unique epidemiological and clinical patterns of Mpox in women. In the United States, a small percentage of Mpox cases were reported among cisgender women, with a notable portion involving non-Hispanic Black or African American, non-Hispanic White, and Hispanic or Latino ethnicities. The primary transmission route was identified as sexual or close intimate contact, with the virus predominantly manifesting on the legs, arms, and genital areas. Further, a study in Spain highlighted significant disparities in diagnosis delays, transmission modes, and clinical manifestations between genders, indicating a different risk profile and disease progression in women. Additionally, a case from Vietnam linked to a new Mpox sublineage in women emphasizes the role of women in the transmission dynamics and the importance of genomic monitoring. This review emphasizes the necessity for inclusive surveillance and research to fully understand Mpox dynamics across diverse population groups, including women. Highlighting gender and sexual orientation in public health responses is crucial for an effective approach to managing the spread and impact of the disease. The findings advocate for a gender-diverse assessment in health services and further research to explore the nuances of Mpox transmission, behavior, and progression among different groups, thereby enhancing the global response to Mpox and similar public health challenges.

Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastics (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete grade C-25, with a compressive strength of 25 MPa, was prepared using an optimum ratio of 14% WG and 6% WP. Mechanical properties were tested at 7 and 28 days of curing. At 20% replacement, workability decreased at water-cement ratios of 0.5 and 0.6 but remained stable at 0.4. Thus, a 0.4 ratio was used. For 10% replacement, compressive strength increased by 12.55% and 6.44% on the 7th and 28th days, respectively. At 20% replacement, compressive strength decreased by 14.35% and 0.73% on the 7th and 28th days, respectively. On the 28th day, splitting tensile strength at optimum replacement was 4.3 MPa, an 8.5% reduction from the control mix. However, flexural strength increased by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, WG and WP improved flexural strength but slightly reduced splitting tensile strength.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

In this paper we compare the effects of forecasting demand using individual (disaggregated) components versus first aggregating the components either fully or into several clusters. Demand streams are assumed to follow autoregressive moving average (ARMA) processes. Using individual demand streams will always lead to a superior forecast compared to any aggregates, however we show that if several aggregated clusters are formed in a structured manner then these subaggregated clusters will lead to a forecast with minimal increase in mean-squared forecast error. We show this result based on theoretical MSFE obtained directly from the models generating the clusters as well as estimated MSFE obtained directly from simulated demand observations. We suggest a pivot-algorithm, that we call Pivot Clustering, to create these clusters. We also provide theoretical results to investigate sub-aggregation, including for special cases such as, aggregating MA(1) streams and ARMA streams with similar or same parameters.

Intercropping of maize (Zea mays L.) and peanuts (Arachis hypogaea L.) (M||P) significantly enhances crop yield. In a long-term M||P field experiment with two P fertilizer levels, we examined how long-term M||P affects topsoil aggregate fractions and stability, organic carbon (SOC), available phosphorus (AP), and total phosphorus (TP) in each aggregate fraction, along with crop yields. Compared to their respective monocultures, long-term M||P substantially increased the proportion of topsoil mechanical macroaggregates (7.6–16.3%) and water-stable macroaggregates (>1 mm) (13.8–36.1%), while reducing the unstable aggregate index (ELT) and the percentage of aggregation destruction (PAD). M||P significantly boosted the concentration (12.9–39.9%) and contribution rate (4.1–47.9%) of SOC in macroaggregates compared to single crops. Moreover, the concentration of TP in macroaggregates (>1 mm) and AP in each aggregate fraction of M||P exceeded that of the respective single crops (P<0.05). Furthermore, M||P significantly increased the Ca2-P, Ca8-P, Al-P, and Fe-P concentrations of intercropped maize (IM) and the Ca8-P, O-P, and Ca10-P concentrations of intercropped peanuts (IP). The land equivalent ratio (LER) of M||P was higher than one, and M||P stubble improved the yield of subsequent winter wheat (Triticum aestivum L.) compared with sole-crop maize stubble. P application augmented the concentration of SOC, TP, and AP in macroaggregates, resulting in improved crop yields. In conclusion, our findings suggest that long-term M||P combined with P application, sustains farmland productivity in the North China Plain by increasing SOC and macroaggregate fractions, improving aggregate stability, and enhancing soil P availability.

This research investigates the effect of pre-soaking treatment on plant-based aggregate using a wet grout binder to formulate a high-strength lightweight concrete (HSLWC). The surface modification utilising a novel grout soaking technique with various water-to-cement (w/c) ratios indicated a new method of approach for the recent development of lightweight plant-based aggregate (LWPA). In this experiment, the fresh and hardened properties of modified LWPA lightweight concrete were assessed by verifying their workability, densities, compressive and split tensile strengths towards the modulus of elasticity. The results showed that pre-soaking plant-based lightweight aggregate (w/c: 0.6, 0.8, 1.0, and 1.2) slightly increased the density of the samples compared to untreated LWPA. The oven-dry density of treated and untreated LWPA is controlled in the range of HSLWC. The outcomes indicated that the workability of the surface- modified LWPA has significant improvement up to 40% in 6 min for (TDS)/0.6 sample compared to the original LWPA. The mechanical properties of the LWPA concrete with surface modification method exhibit substantial increment of compressive strength, split tensile strength, and modulus of elasticity were recorded at 22%, 26%, and 34%, respectively. Significantly, the findings from this scientific method revealed that the pre-soaking treatment method on LWPA has shown to be a highly recommended technique in improving interfacial bonding while performing as one of the most promising solutions to improve the properties of lightweight concrete.

This study is focused on the experimental investigation of compressive strength and durability properties of lightweight concrete mixtures with fine expanded glass and expanded clay aggregates using different microfillers. The paper proposes the relationships between the compressive strength and density of concrete mixtures with different proportions of lightweight aggregates mentioned above. The performed experimental studies have revealed the tendencies of possible usage of different amount of fine lightweight aggregates and their combinations in the production of concrete mixtures depending on the demands of practical application. Following the requirements for structural concrete subjected to environmental effects, durability properties (alkaline corrosion and freeze–thaw resistance) of the selected concrete mixtures with expanded glass aggregate were studied. The results of the experimental investigations have shown that durability of tested concrete specimens was sufficient. The study has concluded that the mixtures under consideration can be applied for the production of structural elements to which durability requirements are significant.

A tricalcium silicate nanoparticle-containing cement (NPC) was developed to overcome the disadvantages of existing mineral trioxide aggregate (MTA) dental materials. This study aimed at evaluating the effects of NPC on the osteogenic differentiation of human periodontal ligament fibroblasts (HPLFs) in vitro, and on the healing of furcal perforations created experimentally in rat molars in vivo, in comparison to MTA. The in vitro studies performed the following assays; pH measurement using a pH meter, the release of calcium ions using a calcium assay kit, cell attachment and morphology using SEM, cell proliferation using a coulter counter, marker expression using quantitative reverse transcription polymerase chain reaction (qRT-PCR) and cell mineralized deposit formation using Alizarin Red S (ARS) staining. In the in vivo studies, MTA and NPC were used to fill the rat molar perforations. Rat molars were processed at 7, 14 and 28 days for analysis of inflammatory processes using hematoxylin and eosin (HE) staining, immunohistochemical staining of Runx2 and tartrate-resistant acid phosphate (TRAP) staining. The results demonstrate that the nanoparticle size distribution of NPC is critical for osteogenic potential at an earlier stage compared to MTA. Further studies are required to elucidate the mechanism of action of NPC in osteogenic differentiation.

Nondipole terms in the atom-laser interaction arising due to the presence of a magnetic component in an electromagnetic wave and its inhomogeneity lead to nonseparability of the center-of-mass (CM) and electron variables in the neutral atom and, as a consequence, to its acceleration. We investigate this effect as well as the accompanying excitation and ionization processes for the hydrogen atom in strong (1012 - 2×1014 W/cm2) linearly polarized short-wavelength (5eV ≲ℏω≲ 27 eV) electromagnetic pulses of about 8 fs duration. The study has been carried out within the framework of a hybrid quantum-quasiclassical approach in which the coupled time-dependent Schrödinger equation for an electron and the classical Hamilton equations for the CM of an atom are simultaneously integrated. Optimal conditions with respect to the frequency and intensity of the electromagnetic wave for the acceleration of atoms without their noticeable ionization are found in the analyzed region.

We introduce a new variation on the domination theme which we call vertex domination as reducing waste of time in transportation planning and optimization of transport routes. We determine the vertex domination number $\gamma_v$ for several classes of fuzzy graphs. The bounds is obtained for it. In fuzzy graphs, monotone decreasing property and monotone increasing property are introduced. We prove both of the vizing's conjecture and the Grarier-Khelladi's conjecture are monotone decreasing fuzzy graph property for vertex domination. We obtain Nordhaus-Gaddum (NG) type results for these parameters. The relationship between several classes of operations on fuzzy graphs with the vertex domination number of them is studied. Finally, we discuss about vertex dominating set of a fuzzy tree by using the bridges and $\alpha$-strong edges equivalence.

The aim of this expository article is to present recent developments in the centuries-old discussion on the interrelations between several types of domination in graphs. However, the novelty even more prominent in the newly discovered simplified presentations of several older results. Domination can be seen as arising from real-world application and extracting classical results as first described by this article.The main part of this article, concerning a new domination and older one, is presented in a narrative that answers two classical questions: (i) To what extend must closing set be dominating? (ii) How strong is the assumption of domination of a closing set? In a addition, we give an overview of the results concerning domination. The problem asks how small can a subset of vertices be and contain no edges or, more generally how can small a subset of vertices be and contain other ones. Our work was as elegant as it was unexpected being a departure from the tried and true methods of this theory that had dominated the field for one fifth a century. This expository article covers all previous definitions. The inability of previous definitions in solving even one case of real-world problems due to the lack of simultaneous attentions to the worthy both of vertices and edges causing us to make the new one. The concept of domination in a variety of graphs models such as crisp, weighted and fuzzy, has been in a spotlight. We turn our attention to sets of vertices in a fuzzy graph that are so close to all vertices, in a variety of ways, and study minimum such sets and their cardinality. A natural way to introduce and motivate our subject is to view it as a real-world problem. In its most elementary form, we consider the problem of reducing waste of time in transport planning. Our goal here is to first describe the previous definitions and the results, and then to provide an overview of the flows ideas in their articles. The final outcome of this article is twofold: (i) Solving the problem of reducing waste of time in transport planning at static state; (ii) Solving and having a gentle discussions on problem of reducing waste of time in transport planning at dynamic state. Finally, we discuss the results concerning holding domination that are independent of fuzzy graphs. We close with a list of currently open problems related to this subject. Most of our exposition assumes only familiarity with basic linear algebra, polynomials, fuzzy graph theory and graph theory.

Pathogenicity of many bacteria including Bacillus cereus and Staphylococcus aureus depends on pore-forming toxins (PFTs), which cause lysis of host cells by forming pores in membranes of eukaryotic cells. Bioinformatic analysis revealed in over 600 PFTs a region homologous to the Lys171-Gly250 sequence in hemolysin II (HlyII) from B. cereus, which we designated as “homologous peptide”. Three β-barrel PFTs were used for a detailed comparative analysis. Two of them –HlyII and cytotoxin K2 (CytK2), – are synthesized in Bacillus cereus sensu lato; the third – S. aureus α-toxin (Hla) – is the most investigated representative of the family. Protein modeling showed certain amino acids of homologous peptide to be located on the surface of the monomeric forms of these β-barrel PFTs. We obtained monoclonal antibodies against both a cloned homologous peptide and a 14-membered synthetic peptide DSFNTFYGNQLFMK as part of homologous peptide. The HlyII, CytK2 and Hla regions recognized by the obtained antibodies, as well as an antibody capable of suppressing the hemolytic activity of CytK2, were identified in the course of the work. Antibodies capable of recognizing PFTs of various origins can be useful tools for both identification and suppression of the cytolytic activity of PFTs.

This article is devoted to the problem of genetically coding of inherited cyclic structures in biological bodies, whose life activity is based on a great inherited set of mutually coordinated cyclic processes. The author puts forward and arguments the idea that the genetic coding system is capable of encoding inherited cyclic processes because it itself is a system of cyclic codes connected with Boolean algebra of logic. In other words, the physiological processes in question are cyclical because they are genetically encoded by cyclic codes. In support of this idea, the author presents a set of his results on the connection of the genetic coding system with cyclic Gray codes, which are one of many known types of cyclic codes. This opens up the possibility of using for modeling inherited cyclic biostructures those algebraic and logical theories and constructions that are associated with Gray codes and have long been used in engineering technologies: Karnaugh maps, Hilbert curve, Hadamard matrices, Walsh functions, dyadic analysis, etc. Additionally, the connections of these constructions with statistical rules of genomic DNAs and binary-genomic numbers are considered.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

Conditional Privacy Preserving Authentication (CPPA) schemes are an effective way of securing communications in Vehicular Adhoc Networks (VANETs), as well as ensuring user privacy and accountability. Cryptanalysis plays a crucial role in pointing out the vulnerabilities in existing schemes to enable the development of more resilient ones. In 2019, Zhang proposed a CPPA scheme for VANET security (PA-CRT), based on identity batch verification (IBV) and Chinese remainder theorem (CRT). In 2023, this scheme was crypt-analyzed by Tao. In this paper we provide our own crypt analysis of Zhang’s scheme and propose counter measures to mitigate Tao’s attacks. Furthermore, in 2021, Xiong proposed a Certificateless Aggregate Signature (CLAS) scheme which was cryptanalyzed by Shim in 2023. Xiong subsequently proposed a modified CLAS scheme which is also cryptanalyzed in this paper.

To study the strengthening effect on recycled concrete columns by carbon fiber composite materials (CFRP) under different levels of seismic damage, four column specimens were designed for pseudo-static tests. The four specimens were respectively non-destructive without strengthening (prototype), non-destructive strengthening, medium seismic damage strengthening and severe seismic damage strengthening, according to the replacement rate of recycled aggregates and the level of seismic damage. The characteristics of the deformation damage and seismic performance indicators of each specimen were compared and analyzed. A decrease was observed in the initial stiffness of the seismically damaged recycled concrete column specimens strengthened with CFRP, while the ductility, peak bearing capacity and energy dissipation capacity of the specimens were improved. On the other hand, with the reduction of seismic damage and the increase of recycled aggregate replacement rate, the ductility and energy dissipation capacity of the reinforced seismic damaged recycled concrete column specimens were enhanced to different levels. In particular, the cumulative energy consumption of the strengthened specimens under medium seismic damage increased most significantly by 32.5%. In general, the hysteretic curves of the strengthened specimens were full, and the average ductility coefficients were 4.1–6.8. CFRP strengthening was more effective in restoring and enhancing the performance of the recycled concrete column specimens with medium and lower seismic damage levels (displacement ratio ≤ 3%).

The reuse of recycled crushed concrete aggregate (RCCA) and reclaimed asphalt pavement (RAP) can provide a sustainable solution for the disposal of C&amp;D materials instead of sending it to landfill. More importantly, it will save energy and reduce impact on the environment. Several states in USA are using RCCA and RAP as base materials for years, focusing on the quality of the recycled materials. The structure of Recycled Aggregate (RA) is more complex than Natural Aggregate (NA). RAs have old mortar adhered on them that forms a porous surface at interfacial transition Zone (ITZ) and prevents new cement mix from bonding strongly with the aggregates. The objective of this work was to correlate microstructural properties like micro-porosity, inter and intra aggregate pores with the unconfined compressive strength (UCS) of RAP and RCCA molds, mixed at different proportions. In this paper, the quantity of micro-pores and their effect on the strength of mixed materials is used as the basis of microstructural analysis of recycled concrete and reclaimed asphalt. Microstructural properties obtained from the analysis of scanning electron microscope (SEM) images were correlated with unconfined compressive strength. Intra-aggregate and inter-aggregate pores were studied for different ratios of cement treated mixture of RAP and RCCA. The results show that the number of pores in the mixture increases considerably by adding RAP, which eventually causes reduction in unconfined compressive strength. In addition, significant morphological and textural changes of recycled aggregates were observed by SEM image analysis.

We propose and experimentally realize a scheme of the optical nonreciprocity (ONR) using degenerate two-level atoms embedded in an optical ring cavity. For the degenerate transition Fg=4→Fe=3, we first study the cavity-transmission property in different coupling field, and verify that within the strong-coupling regime, the single-dark-state peak formed by electromagnetically induced transparency (EIT) shows ONR. Qualitative theoretical analysis shows that the stable ground-state Zeeman coherence is necessary for intracavity EIT. However, due to the frequency degeneracy, the large Rabi frequency of counter-propagating coupling field can reduce the number of effective atoms and weaken the strong-coupling of the atom-cavity, which determines that ONR based on intracavity EIT occurs only at weaker probe intensity. Furthermore, the ONR transmission with high contrast, linewidth-narrowed and broadband is experimentally demonstrated.

The idea of strong and weak adjacencies between vertices has been generalized into fuzzy graphs and intuitionistic fuzzy graphs (IFGs) and it is an important part of making decisions. However, one or two membership degrees are not always sufficient for making decisions on real-world problems that need an answer of types “yes, neutral, and no". Consequently, in previous work, we generalized the concept into picture fuzzy graphs (PFGs) where each element in the PFG has membership, neutral, and non-membership degrees. Moreover, we constructed the notion of the coloring of PFGs based on strong and weak adjacencies between vertices. In this paper, we investigate some properties of the chromatic number of PFGs based on the concept of strong and weak adjacencies between vertices. According to the properties, we construct an algorithm to find the chromatic number of PFGs. The algorithm is usefull when we work with large PFGs. Further, we improve the method to implement the PFG’s coloring for determining traffic signal phasing at an intersection. A case study has also been done to evaluate the method.

In this work we report recent theoretical calculations of a superconducting island in a strong vortex confinement regime. The obtained results reveal the evolution of superconducting condensate as a function of electron mean-free path (l) with the evolution of an applied magnetic field H0. The results of this study provide an insight about the emergent superconducting properties under such conditions, using the Ginzburg-Landau numerical simulations where spatial variation of thickness d on island, omnipresent in these kind of structures grown on Si (111), is taken into account. These results offer a new route to tailor superconducting circuits by using the controlled bombardment, in order to explore the impact on vortex distribution, phase of order parameter, number of vortices, free energy and the first H1 and second critical field H2.

We present simple relations for nuclear stability and nuclear binding energy with respect to three gravitational constants associated with electroweak, strong and electromagnetic interactions.

Natural Gas (NG) processing is a prominent industrial separation process. Among the available techniques, the innovative membrane process shows potential for efficient removal of impurities, including carbon dioxide (CO₂). This study focuses on utilizing breakthroughs in membrane separation to drive sustainable CO₂ extraction from natural gas. Through comprehensive research and analysis, we explore the effectiveness and feasibility of membrane-based systems in removing CO₂ impurities from NG, thus promoting greener and more sustainable industrial practices. Our findings underscore the transformative nature of membrane separation technology, presenting new possibilities for a more environmentally-friendly and sustainable approach to CO₂ extraction from natural gas.Natural Gas (NG) processing utilizes various techniques for impurity removal, with the membrane process emerging as a promising option for efficient carbon dioxide (CO₂) extraction. This research proposes the integration of a simple mathematical model into ASPEN HYSYS to design a membrane system for CO₂/CH₄ separation. The study also investigates parameter sensitivities by altering operating conditions, such as feed composition and pressure, as well as membrane properties, including selectivity. By analyzing these variables, we aim to optimize the performance and efficiency of the membrane system, facilitating the sustainable extraction of CO₂ from NG. The findings contribute to advancing the design and operation of membrane-based processes for CO₂ separation, paving the way for greener and more sustainable industrial practices. In addition, this study explores various configurations for optimizing the design of the membrane system, including single-stage with and without recycling as well as double-stage configurations. The investigation demonstrates that methane recovery can be enhanced through the recycling of the permeate stream and by implementing a double stage membrane system. These findings highlight the potential for improving the efficiency and performance of the membrane system, enabling higher methane recovery rates. By considering different configurations, this research contributes to the development of more effective and sustainable CO₂ extraction processes from natural gas.

Immune checkpoint receptors play a crucial role in steering tumor progression, prompting a focused investigation into the role of TIM3 in breast cancer. Analysis of TCGA BRCA data unveiled diverse correlations between TIM-3 expression and immune cell infiltration across subtypes. In our in-house cohort studied through IHC, significant changes in TIM3 expression with tumor grades were observed. Higher TIM3 expression correlated with increased disease-free survival in pan breast cancer, marking the first revelation of TIM3's positive role in pan BC prognosis. The study indicates that alluring TIM3 response, rather than suppression, may enhance breast cancer prognosis.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

In actuarial practice, the modeling of total losses tied to a certain policy is a non-trivial task. Traditional parametric models to predict total losses have limitations due to complex distributional features such as extreme skewness, zero inflation, multi-modality, etc., and the lack of explicit solutions for log-normal convolution. In the recent literature, the application of the Dirichlet process mixture for insurance loss has been proposed to eliminate the risk of model misspecification biases; however, the effect of covariates as well as missing covariates in the modeling framework is rarely studied. In this article, we propose novel connections among covariate-dependent Dirichlet process mixture, log-normal convolution, and missing covariate imputation. Assuming an individual loss is log-normally distributed, we develop a log skew-normal Dirichlet process to approximate the log-normal sum. As a generative approach, our framework models the joint of outcome and covariates, which allows to impute missing covariates under the assumption of missingness at random. The performance is assessed by applying our model to several insurance datasets, and the empirical results demonstrate the benefit of our model compared to the existing actuarial models such as the Tweedie-based generalized linear model, generalized additive model, or multivariate adaptive regression spline.

In the present trend of constructing taller and longer structures, the application of lightweight aggregate concrete is becoming an increasing important advanced solution in the modern construction industry. In engineering practice, the analysis of lightweight concrete elements is performed using the same algorithms used for normal concrete elements. As an alternative to traditional engineering methods, nonlinear numerical algorithms based on constitutive material models may be used. The paper presents a comparative analysis of curvature calculations for flexural lightweight concrete elements, incorporating analytical code methods EN 1992-1 and ACI 318-14, as well as a numerical analysis using the constitutive model of cracked tensile lightweight concrete recently proposed by the authors. To evaluate the adequacy of the theoretical predictions, experimental data of 51 lightweight concrete beams tested during five different programmes were collected. A comparison of theoretical and experimental results showed that the most accurate predictions are obtained using numerical analysis and the constitutive model proposed by the authors. In the future, the latter algorithm can be used as a reliable tool for improving the design standard methods or numerical modelling of lightweight concrete elements subjected to short-term loading.

In this paper, we study a generalised CIR process with externally-exciting and self-exciting jumps, and focus on the distributional properties and applications of this process and its aggregated process. The first and second moments of this jump-diffusion process are used to calculate the insurance premium based on mean-variance principle. The Laplace transform of the aggregated process is derived, and this leads to an application for pricing default-free bonds which could capture the impacts of both exogenous and endogenous shocks. Illustrative numerical examples and comparisons with other models are also provided.

In recent years, wireless power transfer (WPT) has progressed rapidly in both theory and commercialization abroad. However, existing research into WPT coil design for low-power devices is limited. This paper investigates coil structure using printed circuit board (PCB) for magnetic resonant coupling WPT to address this gap. Specifically, the impacts of key geometric parameters on the coil quality factor and coupling coefficient are analysed through models and simulations. Equivalent PCB coils were formed for mutual inductance models, and four basic compensation circuits were analysed. The impacts of changes in coil thickness, line width, turn spacing, and number of turns on the quality factor of PCB coils were analysed with a fixed outer diameter of the coil. In this paper, to mitigate the coil offset while retaining PCB manufacturing simplicity for practical uses, a dual layer PCB coil structure is proposed. The structure optimizated PCB coil could offer remarkable improvements in the WPT system for low power electronic devices.

The development of integrated, compact, and multifunctional photonic circuits is crucial to increase the capacity of all-optical signal processing for communications, data management or microsystems. Plasmonics brings compactness to numerous photonic functions, but its integration into circuits in not straightforward due to insertion losses and poor modes matching. The purpose of this article is to detail the integration strategies of plasmonic structures on dielectric waveguides, and to show through some examples the variety and the application prospect of integrated plasmonic functions.

Ship pilots and maritime safety administration have an urgent need for more accurate and earlier warnings on strong wind gusts. This study firstly investigates the “Oriental Star” cruise ship cap-sizing event in 2015, one of the deadliest shipwreck events in recent years, and explores all related hydro-meteorological components in a global mesoscale model. It is found that, rather than the missing signal in raw surface wind prediction, the cumulus precipitation variable (CP) increases dramatically during the accident occurrence, which significantly corresponds to the sub-grid strong wind gust. The effective lead-time can be extended from 24hr (deterministic model) to 48hr (en-semble model). This finding is then verified in another two recent deadly cruise boat accidents. The introduction of the new variable is bearing the hope of improvement to the current maritime safeguard system, on predicting sub-grid strong wind gusts for small-size cruise boats in offshore and inland rivers. Finally, an automatic-response system is developed to provide economical con-vection prediction via Inmarsat email communication, aiming to explore operational severe con-vective gust early-warning and appropriate numerical mesoscale model application.

In an historic perspective on the development of the Standard Model of particle physics it is shown how mathematically driven axioms have masked the merits of a physically comprehensible structural view. It is concluded that the difference between the two approaches can be traced back to two major issues. Whereas in the Standard Model the quark is a Dirac particle with a single real dipole moment, the quark in the structural model, in confinement with other quarks, is a Dirac particle with two real dipole moments. The second issue is the view that empty space does not exist, but that space is filled with a polarisable energetic fluid. It is shown how recognition of these two issues pave a road to reconcile particle physics with gravity, in which the quark can be seen as a magnetic electron and in which the gluon, as the strong force carrier, can be seen as a massive photon.

We report the strong coupling between plasmonic surface lattice resonances (SLRs) and photonic Fabry-Pérot (F-P) resonances in a microcavity embedded with two-dimensional periodic array of metal-insulator-metal nanopillars. For such a plasmonic-photonic system, we show that the SLR can be strongly coupled to the F-P resonances of both the odd- and even orders, and that the splitting energy reaches as high as 138 meV in the visible regime. We expect that this work will provide a new scheme for strong coupling between plasmonic and photonic modes.

It remains unclear in the literature what is the cause of the so-called alkali-carbonate reaction (ACR) damage to concrete yet, a consensus is reached when considering dedolimitization as non-expansive. However, expansion and cracks as distress features are often attributed to alkali-silica reaction (ASR) when evidence of a reactive mineral is found in the aggregate. Evidently, different types of aggregates may produce different types and degrees of damage. Therefore, this work aims to assess the damage to concrete generated and propagated by the so-called ACR susceptible reactive Kingston coarse aggregate through mechanical testing (i.e., direct shear test), microscopy (the damage rating index – DRI), and other techniques. Distinct induced expansion levels (i.e., 0%, 0.05%, 0.12%, and 0.20%) were selected to compare the distress caused by ACR to concrete affected by ASR. Result show that the behaviour of ACR, namely as captured through the DRI, is inconsistent with that of ASR thus attesting to ACR being a distinct distress mechanism.

This review article is devoted to the colloidal properties of fullerene solutions. According to generally accepted understanding, all solvents in relations to fullerenes are divided into “good” (or “strong” or “high-solubility” ones), “poor” (usually polar) and “reactive”. Water occupies a special place, close to “poor” solvents. We have consistently considered and discussed the state of fullerenes in these systems. In "good", predominantly non-polar aromatic solvents and CS2, nonequilibrium dissolution methods lead to the formation of colloidal aggregates, whereas utilization of equilibrium methods results in the formation of molecular solutions. The latter, however, have some unusual properties; new results confirm previously expressed ideas about colloidal properties of these solutions. Both experimental and theoretical methods devoted to such systems are considered. In “poor” (polar) solvents, typical lyophobic colloidal systems appear. Both “bottom-up” and “top-down” methods of preparation are now well documented in the literature. However, some of these polar solvents dissolve fullerenes rather easily and with less energy consumption. In addition to N-methylpyrrolidin-2-one, which has been well studied for fullerenes, DMSO and DMF have now been described. These solvents can be considered a subset of poor solvents that have some features of being “reactive” at the expense of basic (“cationophilic”) properties. Room temperature ionic liquids are also used to dissolve fullerenes, but there is little experimental research. Hydrosols and aqueous suspensions of fullerenes are typical hydrophobic colloids that obey the Schulze–Hardy rule and other regularities in the presence of electrolytes. New experimental data confirm the previously obtained results. Organosols in acetonitrile and methanol are much less stable with respect to electrolytes; the difference in critical coagulation concentrations of electrolytes reaches two to three orders of magnitude. This allows us to conclude that there is an additional, so-called non-DLVO, stabilizing factor in the hydrosols. Accordingly, the value of the Hamaker constant of fullerene-fullerene interaction may be higher than that derived from coagulation data in water. Contrary to the mentioned “poor” polar solvents, the stability of fullerene sols in DMSO is even higher than in water. These results, as well as data obtained with DMF demonstrate strong solvation of fullerenes with basic solvents.

In the modern construction industry, lightweight aggregate concrete (LWAC) is often used in the production of load-bearing structural members. LWAC can be up to 40% lighter by volume in comparison to normal strength concrete. On the other hand, the lack of adequate numerical models often limits the practical application of innovative building materials, such as lightweight concrete, in real projects. This trend is due to the uncertainties in design standard methods and calculation errors, the level of which is generally unacceptable to civil engineers in terms of safety and reliability. In the present paper, a comparative numerical deformation analysis of a full-scale bridge deck slab and girder has been carried out. Using the physical model proposed by the authors and the finite element software ATENA, the deformations of full–scale lightweight and traditional reinforced concrete elements under short-term effects of permanent and variable loads was compared. Depending on the safety and serviceability limit requirements, it was found that the amount of longitudinal reinforcement in lightweight reinforced concrete elements can be reduced compared to normal reinforced concrete elements with the same parameters. The results of the numerical analysis show that the deformation analysis model proposed by the authors can be a reliable tool for the design of lightweight concrete flexural members by selecting the optimum geometrical and reinforcement parameters limited by the stiffness condition.

With our long experience in the field of unification of gravity and quantum mechanics, we understood that, when mass of any elementary is extremely small/negligible compared to macroscopic bodies, highly curved microscopic space-time can be addressed with large gravitational constants and magnitude of elementary gravitational constant seems to increase with decreasing mass and increasing interaction range. In our earlier publications, we proposed that, 1) There exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions; 2) There exists a strong interaction elementary charge in such a way that, it's squared ratio with normal elementary charge is close to inverse of the strong coupling constant; and 3) Considering a fermion-boson mass ratio of 2.27, quarks can be split into quark fermions and quark bosons. Further, we noticed that, electroweak field seems to be operated by a primordial massive fermion of rest energy 584.725 GeV and hadron masses seem to be generated by a new hadronic fermion of rest energy 103.4 GeV. In this context, starting from lepton rest masses to stellar masses, we have developed many interesting and workable relations. With further study, a workable model of final unification can be developed.

Here we evaluate the chemistry of mineral soil solutions collected by suction lysimeters in a small mountain catchment that was affected by acidification-related spruce die-back. The aim was to obtain new insights into spatial patterns of nutrient partitioning during acidification recovery. This was achieved by comparing nutrient concentrations in soil solutions, collected along a V-shaped valley, with those in runoff. Five nests of suction lysimeters were installed in the 33-ha UDL catchment at different topographic positions (hilltops, slopes and valley). Following a 1-year equilibration, monthly samples of soil solutions were collected over a 2-year period. In the vicinity of each lysimeter nest, soil pits were excavated for a study of soil chemistry. Soil solutions were analyzed for SO42-, NO3-, DOC, NH4+, Na+, K+, Ca2+, Mg2+, and total dissolved Al concentrations, DOC and pH. For a P release estimation, ammonium oxalate extraction of soil samples was performed. Comparison of soil water data from this study with other European studies indicated that major environmentally relevant chemical species at UDL had concentrations similar to median concentrations across numerous previously acidified sites. CEC (≤ 58 meq kg-1) and BS (≤ 13 %), however, were significantly lower at UDL than at other European sites, documenting incomplete recovery from acidification. Spatial trends and seasonality in soil water chemistry support belowground inputs from mineral-stabilized legacy pollutants and soil nutrients. Seasonal variability of soil water sulfate and nitrate was significant. High nitrate in soil solutions during summer originated during the preceding dormant season, and high sulfate concentrations observed during the winter originating from recycled organic S during the summer. Higher concentrations of SO42-, NO3-, and base cations in runoff than in soil solutions may be explained by lateral surficial runoff leaching pollutants and nutrients from very shallow soil horizons. Nearly 30 years after peak acidification, solutions in mineral subsoil at UDL exhibited similar concentrations of SO42-, Ca2+ and Mg2+ as median values at the Pan-European International Co-operative Program (ICP) Forest sites, yet NO3- concentrations were an order of magnitude higher than the ICP sites. Calcium applied on soil surface by liming 32 to 11 years ago affected runoff more than soil solutions, suggesting contribution of both shallow soil water and groundwater to runoff.

In this paper, a kind of single-walled carbon nanotube nonlinear model is developed, and the strongly nonlinear dynamic characteristics of such carbon nanotubes subjected to random magnetic field are studied. The nonlocal effect of microstructure is considered based on the theory of nonlocal elasticity. The natural frequency of the strongly nonlinear dynamic system is obtained by the energy function method, the drift coefficient and the diffusion coefficient are verified. The stationary probability density function of the system dynamic response is given and the fractal boundary of the safe basin is provided. Theoretical analysis and numerical simulation show that stochastic resonance occurs when varying the random magnetic field intensity. The boundary of safe basin has fractal characteristics and the area of safe basin decreases when the intensity of the magnetic field permeability increases.

The demand for efficient processes through a comprehensive understanding and optimization of welding conditions continues to grow in the manufacturing industry. This study involves heat-resistant 2.25 Cr-1 Mo V-groove steel welding using the square-waveform alternating cur-rent. Experiments were conducted to build the relationship between input variables—such as current, frequency, electrode negativity ratio, and welding speed—and process performance, such as penetration, bay area, deposition rate, melting efficiency, percentage dilution, flux–wire ratio, and heat input. The process was analyzed in light of the defect-free high-deposition weld groove weld, the sensitivity to process parameters, and the optimization and development of the process map. The study proposes an innovative approach to reducing the cost and time of optimizing the one-pass-each-layer V-groove welding process using bead-on-plate welds. Square waveform welding creates a metallurgical notch in the form of a bay at the fusion boundary that can be minimized by selecting appropriate welding conditions. The square waveform submerged arc welding is more sensitive towards changes in current and welding speed than the frequency and electrode negativity ratio; however, the electrode negativity ratio and frequency are minor but helpful parameters to achieve optimal results. The proximity of the planned and experimental results to within 3% confirms the validity of the proposed approach. The investigation shows that 90% of the maximum deposition rate is possible for one-pass-each-layer V-groove welds within heat input and weld width constraints.

Metal nanoparticles supporting plasmons are widely used to enhance electromagnetic fields, resulting in strong light-matter interactions at the nanoscale in a diverse range of applications. Recently, it has been shown that when metal nanorods are periodically arranged with proper lattice periods, surface lattice resonances (SLRs) can be excited and near fields can be greatly enhanced over extended volumes. In this work, we report significant near field enhancement over even larger volumes by placing the metal nanorod array within a Fabry-Pérot (F-P) microcavity. Results show that taking advantage of strong coupling between the SLR and the photonic F-P resonances, the electric field intensity of the bonding split mode can be enhanced by up to 1935 times, which is about three times of the enhancement of the SLR, and the greatly enhanced field can extend over most of the F-P microcavity. We further show that the F-P resonances of both odd and even orders can strongly couple to the SLR by varying the nanorods position from the middle of the microcavity. We expect that the proposed plasmonic-photonic coupling system will find promising applications in nanolasers, nonlinear optics and sensing.

In this paper, we introduce a new iteration scheme, named as the S**-iteration scheme, for approximation of fixed point of the nonexpansive mappings. This scheme is faster than Picard, Mann, Ishikawa, Noor, Agarwal, Abbas, Thakur, and Ullah iteration schemes. We show the stability of our instigated scheme and give a numerical example to vindicate our claim. We also put forward some weak and strong convergence theorems for Suzuki's generalized nonexpansive mappings in the setting of uniformly convex Banach spaces. Our results comprehend, improve, and consolidate many results in the existing literature.

For the first time, We do fuzzification the concept of domination in crisp graph on a generalization of fuzzy graph by using membership values of vertices, α-strong edges and edges. In this paper, we introduce the first variation on the domination theme which we call vertex domination. We determine the vertex domination number γ_v for several classes of t-norm fuzzy graphs which include complete t-norm fuzzy graph, complete bipartite t-norm fuzzy graph, star t-norm fuzzy graph and empty t-norm fuzzy graph. The relationship between effective edges and α-strong edges is obtained. Finally, we discuss about vertex dominating set of a fuzzy tree with respect to a t-norm ⨂ by using the bridges and α-strong edges equivalence.

At nuclear scale, we present three heuristic relations pertaining to strong and electroweak coupling constants. With these relations, close to beta stability line, it is possible to study nuclear binding energy with a single energy coefficient of magnitude $\left(\frac{1}{{\alpha }_s}\right)\left[\frac{e^2}{4\pi {\epsilon }_0{R}_0}\right]\approx 10.0\text{MeV}\text{.}$ With reference to up and down quark masses, it is also possible to interpret that, nuclear binding energy is proportional to the mean mass of $\left[\left(2m_u+m_d\right)\text{and}\left(m_u+2m_d\right)\right]\approx 10.0\text{MeV}.$

Air pollution has been a major environmental issue worldwide from the last few decades. It is a man-made issue that has a serious harmful impact on the environment and the health of humans. There are different sources of emission, but industrial processes and motor vehicles contribute to a chief part of air pollution. It has acute as well as chronic effects on the health of humans and affects different organs. It is thought the main environmental risk factor in the incidence and progression of several diseases such as lung cancer, asthma, Alzheimer's and Parkinson's diseases. Long-term exposure to air pollution has different toxicological impacts on humans such as respiratory and cardiovascular diseases, neuropsychiatric complications, eye irritation and skin diseases. As per the study by the World Health Organization (WHO), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O₃), sulfur dioxide (SO₂), volatile organic compounds (VOCs) and heavy metals are the major air contaminants. These pollutants are different in their properties, composition and time of disintegration. The aim of this study is to review the different sources, types, impacts, challenges and mitigation of air pollution in detail.

Highly-correlated electrons – electrons that engage in strong electron-electron interactions – have been observed in transition metal oxides and quantum dots and can create unusual material behavior that is difficult to model, such as switching between a low resistance metal state and a high resistance Mott insulator state. Tests of devices using a layer-by-layer deposition process for forming multilayer arrays of ferritin (a transition metal (iron) oxide storage protein) have been previously reported that indicate that highly-correlated electron transport is occurring, consistent with models of electron transport in quantum dots. This paper reports the results of the effect of various degrees of structural homogeneity on the electrical characteristics of these ferritin arrays, as well as demonstrating that these structures can provide a switching function associated with the circuit that they are contained within, consistent with the observed behavior of highly-correlated electrons.

As there exist no repulsive forces in strong interaction, in a hypothetical approach, strong interaction can be assumed to be equivalent to a large gravitational coupling. Based on this concept, strong coupling constant can be defined as a ratio of the electromagnetic force and the gravitational force associated with proton, neutron, up quark and down quark. With respect to the product of strong coupling constant and fine structure ratio, we review our recently proposed two semi empirical relations and coefficients 0.00189 and 0.00642 connected with nuclear stability and binding energy. We wish to emphasize that- by classifying nucleons as ‘free nucleons’ and ‘active nucleons’, nuclear binding energy can be fitted with a new class of ‘three term’ formula having one unique energy coefficient. Based on the geometry and quantum nature, currently believed harmonic oscillator and spin orbit magic numbers can be considered as the lower and upper “mass limits” of quark clusters.

The pride of power of the Spanish preachers of religious art is reflected in the church of Santo Domingo built between 1541 and 1688. This work of heritage architecture, one of the first to be built in the colonized city, was affected by multiple earthquakes, interventions, and constructions that do not have a clear record. A total of 13 samples were taken from the lining mortar inside the cloister, central nave, and side chapel, following the nondestructive testing protocols and standards suggested by the research team. The analysis included mineral characterization studies and quantitative analysis by X-ray diffraction and scanning electron microscopy with microanalysis of the samples. The results showed the presence of volcanic aggregates and lime lining and joint mortars, mortars of rustic composition and coarse manufacture. The resolution of the data of mineralogical composition and texture has allowed us to corroborate the historical information described by the chroniclers and to date relatively the studied sites and to establish a hypothesis of constructive stages.

The Ayers Rock of Australia which is known for its charming colors at different time is actually the Celestial Body Ring of the planet Earth that implies the great Celestial Body Love happened on Earth long long ago. The Tasmania island of Australia which is known for the World Heart is actually in the state of face to face with the main island of Australia, which implies the image spokesperson for the inner core (the heart) of the planet Earth. In other words, with the outline of the main island of Australia, the basic key information of the inner core of the planet Earth could be easily obtained by deducing logically, just like the similarity between the fists and heart of human body. Similar to the mechanism of the blood circulation dominated by the heart of human body, it is dominated and motivated by the inner core of the Earth which forms the circulation of mantle magma between the crust and the inner core, and what leads to the formation of expanding and active area on the equatorial and middle-lower latitude area and the silent and convergent area on the North and South Pole central area. Therefore, the mantle magma whirlpools under the crust on the North and South Pole are supposed to exist logically. The walking sideways of the crabs just implies the celestial body language of the motive trend of the main island of Australia based on their similar outline.

With reference to electromagnetic interaction and Abdus Salam’s strong (nuclear) gravity, 1) Square root of ‘reciprocal’ of the strong coupling constant can be considered as the strength of nuclear elementary charge. 2) ‘Reciprocal’ of the strong coupling constant can be considered as the maximum strength of nuclear binding energy. 3) In deuteron, strength of nuclear binding energy is around unity and there exists no strong interaction in between neutron and proton. $G_s\cong 3.32688\times {10}^{28}{\mathrm{m}}^3{\mathrm{kg}}^{-1}{\sec }^{-2}$ being the nuclear gravitational constant, nuclear charge radius can be shown to be, $R_0\cong \frac{2G_s{m}_p}{c^2}\cong 1.24\mathrm{fm}.$ $e_s\cong \left(\frac{G_s{m}_p^2}{\hslash c}\right)e\cong 4.716785\times {10}^{-19}\mathrm{C}$ being the nuclear elementary charge, proton magnetic moment can be shown to be, ${\mu }_p\cong \frac{e_s\hslash }{2m_p}\cong \frac{e{G}_s{m}_p}{2c}\cong 1.48694\times {10}^{-26}\mathrm{J}{.\mathrm{T}}^{-1}.$ ${\alpha }_s\cong {\left(\frac{\hslash c}{G_s{m}_p^2}\right)}^2\cong 0.1153795$ being the strong coupling constant, strong interaction range can be shown to be proportional to $\exp \left(\frac{1}{{\alpha }_s^2}\right).$ Interesting points to be noted are: An increase in the value of ${\alpha }_s$ helps in decreasing the interaction range indicating a more strongly bound nuclear system. A decrease in the value of ${\alpha }_s$ helps in increasing the interaction range indicating a more weakly bound nuclear system. From $Z\cong 30$ onwards, close to stable mass numbers, nuclear binding energy can be addressed with, ${\left(B\right)}_{A_s}\cong Z\times \left\{\left(\frac{1}{{\alpha }_s}+1\right)+\sqrt{\sqrt{30\times 31}}\right\}\left(m_n-m_p\right)c^2\approx Z\times 19.66\mathrm{MeV}.$ With further study, magnitude of the Newtonian gravitational constant can be estimated with nuclear elementary physical constants. One sample relation is, $\left(\frac{G_N}{G_s}\right)\cong \frac{1}{2}{\left(\frac{m_e}{m_p}\right)}^{10}\left[\sqrt{\frac{G_F}{\hslash c}}/\left(\frac{\hslash }{m_{e}c}\right)\right]$ where $G_N$ represents the Newtonian gravitational constant and $G_F$ represents the Fermi’s weak coupling constant. Two interesting coincidences are, ${\left(m_p/m_e\right)}^{10}\cong \exp \left(1/{\alpha }_s^2\right)$ and $2G_s{m}_e/c^2\cong \sqrt{G_F/\hslash c}.$

This study introduces a remote sensing application using satellite imagery to survey a network-scale aggregate stockpile inventory. First, a real scale aggregate quarry site was surveyed using a small Unmanned Aerial Vehicle (sUAV) to produce digital terrain models that enabled analysis of aggregate pile geometry. Second, a lab experiment was designed and performed to validate the applicability of close-range Structure from Motion (SfM) photogrammetry for measuring aggregate piles' physical properties such as volume and density. The other part of the lab experiment delved into direct measurement of aggregate density under varying compaction efforts. These experimental results, in conjunction with some simplifying assumptions, enabled the calculation of aggregate stockpile volumes and estimated weights from satellite imagery. We estimated that an inventory of 4.4 and 1.1 million metric tons of crushed aggregates and Reclaimed Asphalt Pavement (RAP), respectively, stockpiled in Washington State for asphalt production in 2017. The merit of producing such database was further showcased in an example on the economic and environmental impacts of material transportation. We approximated that hauling aggregates from quarry plants to construction sites within Washington State incurs a cost of about $50 thousand to over $4 million, consumes about 0.25 to 20 TJ of energy, and emits 20 to over 1,500 tons of CO₂-eq per asphalt plant annually.

The objective of this study was to analyze the epidemiological links of HIV, HCV and HIV-HCV coinfections to less studied types of transmission in certain populations. We performed an observational, prospective study on 903 patients aged between 15-87 years who took part in the Open Test Project. They were divided into two subgroups: general population and individuals from prisons, and questioned about multiple risk factors. Chi-Square Independence Test was used to establish correlations between the risk factors and the results of the screening tests. Logistic regression was used to calculate the probability of a reactive screening test based on each independent risk factor and age. HIV was very strongly associated with unprotected sexual intercourse with HIV-positive partners (the strongest association), unprotected sexual intercourse with sex workers, newly diagnosed sexually transmitted diseases (STDs), intravenous drug use (IDUs) and sharing injecting materials. In the case of HCV reactive tests, very strong associations have been established with injecting drug use (the strongest association), unprotected sexual intercourse with IDUs and sharing injecting materials. Our study indicates the need for implementing targeted public health programs, tailored to the local epidemiology that can ultimately lead to micro-elimination of hepatitis and HIV infections in this area.

We prove a quasi-pseudometric version of the strong Ekeland principle proved by P. Georgiev and T. Suzuki.

A Berry geometrical phase is identified in a strongly metastable system containing dynamically responsive clathrate hydrate structures within a crystal-fluid material. High energy degeneracy in the associated chemistry produces local stability and false vacuum conditions that lead to non-extensive and non-additive contributions in the fundamental thermodynamic relation. Application of Ginzburg-Landau theory and the scaling laws reveals a coherence length and a penetration depth for a macro-scale dual superconductor. The coherence length determines non-extensive volume changes whilst its inverse gives the Higgs mass. The penetration depth determines the extent of QCD vacuum suppression whilst its inverse gives the vector boson mass together with indirect manifestation as non-additive hyperbolic curvature. Simultaneous emergence of the Ginzburg-Landau superconducting phase transition is consistent with gauge-invariant coupling of the scalar field to the Yang-Mills action in QCD. The discovery of an energy gap in the gradient energy term of the system Lagrangian is associated with a critical correlation length revealed in the transition from a gapped to a gapless superconducting state. Together with the emergence and absorption of the Higgs-like scalar field, a mechanism for describing a renormalized QCD mass gap arises.

In this article, many experimental similarities between electromagnetic fields (which are applied in systems of electrons, atoms, and liquids) and strong interaction fields (which are applied in systems of quarks, nucleons, and nuclei) are reviewed. The currently accepted theories describing electromagnetic fields differ fundamentally from those describing strong fields. Therefore, the many similarities are quite surprising, and some are not adequately explained even today. Several such unexplained similarities are listed among the top open problems in particle physics, such as the “EMC effect,” the “proton spin crisis,” and the “strong CP problem.” This paper highlights, for the first time, the underlying common characteristics of these problems, potentially offering valuable contribution to future explanations.

Strong-aroma Baijiu is a traditional Chinese spirit distilled from grains that undergo solid-state fermentation. At the end of each fermentation cycle, a significant quantity of Huangshui accumulates at the bottom of the fermentation pit, constituting one of the primary by-products in the brewing process of strong-flavor liquor. In this report, the chemical component analysis of Huangshui obtained from a strong-flavor liquor factory revealed a diverse array of organic acids, alcohols, esters, starch, reducing sugars, amino acids, and other compounds present in Huangshui. Additionally, two specialized solid-state fermentation models were developed to investigate the formation process of Huangshui. Our findings demonstrate a positive correlation between the yield of Huangshui and the initial moisture content of fermented grains. It is concluded that Huangshui is the percolate produced during the solid-state brewing process of strong-flavor liquor, with its water content originating from the initial moisture of fermented grains.

In this paper, the authors employ Mountain Pass Lemma, the method of weak solution regularization and Lyapunov function method to derive the unique existence of globally exponential stable positive stationary solution of a single-species model with diffusion and delayed feedback. The obtained stability criterion illuminates that under some suitable conditions, a certain internal competition is conducive to the overall stability of the population, and a certain amount of family planning is conducive to the overall stability of the population. A numerical example and three tables show the effectiveness of the proposed methods.

QSO B0218+357 is a blazar located at a cosmological redshift of 0.944. The source is gravitationally lensed by a spiral galaxy located at the redshift of 0.68. Strong gravitational lensing splits the signals emitted by the source into two components separated by 10-12 days, as observed in radio and gamma-ray bands. In July 2014 a GeV flare was observed by Fermi-LAT, triggering follow-up observations with the MAGIC telescopes at energies above 100 GeV. The expected time delay between the components allowed us to plan broad band MWL observations before, during and after the trailing component of the emission. The MAGIC observations at the expected time of arrival of the trailing component resulted in the first detection of QSO B0218+357 in Very-High-Energy (VHE, >100 GeV) gamma rays. It is both the farthest known VHE object and one of only a few Flat Spectrum Radio Quasars detected in this energy range. We report here the observed multiwavelength spectral and temporal properties of the emission during the 2014 flare.

To follow the growth and development of each tree (N = 1200) Pinus sylvestris L., var. Negorelskaya starting from the seed and continuing at the juvenile (or even generative) stage is the goal of an ambitious project to create a plant passport if possible. Five datasets of replenished empirical (tab-ular and file) and systematic data reflect the early results of a unique ongoing experiment conducted with families moved along a climatic gradient from the collection area (1731 degree days, 722 mm) to the experimental area (2326 degree days; 786 mm). Datasets of morphometric, VIS-spectrometric, and germination seed data, combined with the first results of biometric data (including the Dickson quality index) of seedlings produced from these seeds, will allow scientists in the future to conduct correlation and other statistical analysis, or train a neural network to determine the presence of connections between a seed and a plant. These data contribute to the early non-destructive diag-nosis and grading of seeds according to VIS-spectrometric properties. This dataset structure can complement the FLR-Library. In the future, by tracing seedlings in their early growth (for example, over three growing seasons at the site being restored), it will be possible to determine the degree of intensification of FRM production depending on the initial properties of the seed.

There exists an implicit potential limitation in every physical discoveries that has been implemented and understood. However, the limitations can be bounded within a safe limit to prevent any constructing theory to be free from errors. As, it’s the inert nature of the humans, to go far beyond the scope of experimental findings in order to pursue any studies with the sole help of logical reasoning and mathematics, the argument can be prevailed in the form of WEAK Clampdown Effect & STRONG Clampdown Effect. More, the theories are constructed out of physical nature, more the theory gets hypothetical without any finding evidence, but that does or doesn’t actually justify the phenomenon, that too with the more increment of KARDASHEV Scale, more moderate ways of experimentation got developed curbing down the limitations within the human limit of ‘ERRORS’, that does can be neglected by approximation. Relationship being cross-judgmental on the basis of the computational limits and calculation accuracy, leading to a soft singularity, as a warning, that if computer powers cannot be checked on the basis of error approximations, then this may lead to the hitting of a hard singularity, that in phase with the forbidden gap (or after the optimum limit that arises at the core constraints of nature) to prevent the computation being carried off with respect to super-intelligence machines that are cognitive capability oriented future computers responsible for self growth & reproduction with more improvement algorithm, restricting all forms of humanity & constraints the human growth by virtue of limiting capacities of the humans as compared to computers.

In this paper, we study a three step iterative scheme to approximate fixed points of Suzuki's generalized non-expansive mappings. We establish some weak and strong convergence results for such mappings in uniformly convex Banach spaces. Further, we show numerically that iterative scheme (1.8) converges faster than some other known iterations for Suzuki's generalized non-expansive mappings. To support our claim, we give an illustrative example and approximate fixed points of such mappings using Matlab program. Our results are new and generalize several relevant results in the literature.

The interaction of electrons with strong laser fields is usually treated with semiclassical theory, where the laser is represented by an external field. There are analytic solutions for the free electron wave functions, which incorporate the interaction with the laser field exactly, but the joint effect of the atomic binding potential presents an obstacle for the analysis. Moreover, the radiation is a dynamical system, the number of photons changes during the interactions. Thus, it is legitimate to ask how can one treat the high order processes nonperturbatively, in such a way that the electron-atom interaction and the quantized nature of radiation be simultaneously taken into account? An analytic method is proposed to answer this question in the framework of nonrelativistic quantum electrodynamics. As an application, a quantum optical generalization of the strong-field Kramers-Heisenberg formula is derived for describing high-harmonic generation. Our formalism is suitable to analyse, among various quantal effects, the possible role of arbitrary photon statistics of the incoming field. The present paper is dedicated to the memory of Prof. Dr. Fritz Ehlotzky, who had significantly contributed to the theory of strong-field phenomena over many decades.

To understand the mystery of final unification, in our earlier publications, we proposed two bold concepts: 1) There exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions. 2) There exists a strong elementary charge in such a way that its squared ratio with normal elementary charge is close to reciprocal of the strong coupling constant. In this paper we propose that, can be considered as a compound physical constant associated with proton mass, electron mass and the three atomic gravitational constants. With these ideas, an attempt is made to understand nuclear stability and binding energy. In this new approach, nuclear binding energy can be fitted with four simple terms having one unique energy coefficient with a formula, where is an estimated mean stable mass number. With this new approach, Newtonian gravitational constant can be estimated in a verifiable approach with a model relation of the form, where is the Fine structure constant. Estimated and is 62 ppm higher than the CODATA recommended It needs further investigation. Proceeding further, an attempt is made to fit the recommended quark masses.

It is extremely fascinating and astonishing that the gravitational field on the surface of a neutron star is with a relativistic mass density of 2.65*10¹⁶~5.87*10¹⁸kgm^-3 which can be larger than the mass density of the neutron star (~10¹⁷kgm^-3).Therefore, it is the author’s first intuitional imagining that this field could directly convert into mass. In so strong a gravitational field, electron and proton could be produced directly from graviton–photon collision. The gravitational field exists in everywhere in our universe. No vacuum that the region of a space is “empty” does exist. A particle is clearly always being acted on by the gravitational field. The quantum vacuum fluctuation and vacuum polarization need be re-understood with the interaction between photon and gravitational field. Therefore, the gravitational field is naturally one of the foundations of modern physics.

An attempt is made to model the atomic nucleus as a combination of bound and free or unbound nucleons. Due to strong interaction, bound nucleons help in increasing nuclear binding energy and due to electroweak interaction, free or unbound nucleons help in decreasing nuclear binding energy. In this context, with reference to proposed 4G model of final unification and strong interaction, recently we have developed a unified nuclear binding energy scheme with four simple terms, one energy coefficient of 10.1 MeV and two small numbers 0.0016 and 0.0019. In this paper, by eliminating the number 0.0019, we try to fine tune the estimation procedure of number of free or unbound nucleons pertaining to the second term with an energy coefficient of 11.9 MeV. It seems that, some kind of electroweak interaction is playing a strange role in maintaining free or unbound nucleons within the nucleus. It is possible to say that, strong interaction plays a vital role in increasing nuclear binding energy and electroweak interaction plays a vital role in reducing nuclear binding energy. Interesting observation is that, Z can be considered as a characteristic representation of range of number of bound isotopes of Z. For medium, heavy and super heavy atoms, beginning and ending mass numbers pertaining to bound states can be understood with 2Z+0.004Z^2 and 3Z+0.004Z^2 respectively. With further study, neutron drip lines can be understood. Based on this kind of data fitting procedure and by considering the mass ratio of pions and electroweak bosons, existence of our 4G model of electroweak fermion of rest energy 584.725 GeV can be confirmed confidently.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Previous studies generally reckon that the full converter-base wind power generation (FCWG) is a ’decoupled’ power source from the grid, which hardly participates in electromechanical oscillations. However, it is found recently that strong interaction could be induced which might incur severe resonance incidents in electromechanical dynamic timescale. In this paper, the participation of FCWG in electromechanical dynamics is extensively investigated, and particularly, an unusual transition of electromechanical oscillation mode (EOM) is uncovered for the first time. The detailed mathematical models of open-loop and closed-loop power systems are firstly established, and modal analysis is employed to quantify the FCWG participation in electromechanical dynamics, with two new mode identification criteria, i.e., FCWG dynamics correlation ratio (FDCR) and quasi-electromechanical loop correlation ratio (QELCR). On this basis, the impact of different wind penetration levels and controller parameter settings on the participation of FCWG is investigated. It is revealed that if an FOM has a similar oscillation frequency to the system EOMs, there is a high possibility to induce strong interactions between FCWG dynamics and system electromechanical dynamics of the external power systems. In this circumstance, an interesting phenomenon may occur that an EOM may be dominated by FCWG dynamics, and hence is transformed into a quasi-EOM, which actively involves the participation of FCWG quasi-electromechanical state variables.

The production of particles outside the region of nucleon-nucleon kinematics due to interactions involving dense cold clusters of quark-gluon matter in nuclei is calculated. The possibility of observing this process in the region of central rapidities and large transverse momenta in heavy ion collisions at low energies with MPD detector at the NICA collider has been demonstrated.

In this paper, we introduce a new formulation based on Floquet (Fourier) spectral analysis combined with a spectral modulation technique (and its spatial form) to study strongly coupled sublattices predefined in the infinite and large finite extent of almost periodic antenna arrays (e.g metasurfaces). This analysis is very relevant for dense massive MIMO, intelligent surfaces, 5G, and 6G applications (used for very small areas with a large number of elements such as millimeter and terahertz waves applications). The numerical method that is adopted to model the structure is the method of moments simplified by equivalent circuits MoM GEC. Other numerical methods (as the ASM array scanning method and windowing Fourier method) used this analysis in their kernel that to treat periodic and pseudo-periodic (or quasi-periodic) arrays.