In this paper, a special recurrent neural network (RNN) called \emph{Long Short-Term Memory (LSTM)} is used to design a virtual load sensor that estimates the mass of heavy vehicles. The estimation algorithm consists of a two-layer LSTM network, with the two layers based on sequence-to-sequence and sequence-to-one logic, respectively. The network estimates the vehicle mass based on the vehicle speed, longitudinal acceleration, engine speed, engine torque, and the accelerator pedal position. The network is trained and tested with a data set collected in a high-fidelity simulation environment called Truckmaker. Training data is generated in acceleration maneuvers in a range of speeds whereas test data is obtained by simulating the vehicle in a Worldwide harmonized light vehicles test cycle (WLTC). Preliminary results show that, with the proposed approach, the heavy-vehicle mass can be estimated as accurately as commercial load sensors in a range of load mass as wide as four tons.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

As formally is known, nanozymes are the nanomaterials or nanoscale materials which reveal enzyme-like properties. These nanomaterilas can be utilzied instead of the natural enzymes for simulation of enzymatic reactions in harsh environmental conditions. Among different nanoscale enzyme-like materials, the majority of them reveal peroxidase-like activity, due to the high catalytic efficiency and stability of peroxidase-like nanozymes, they had been widely utilized for sensing and detection via constructing the colorimetric and fluorescence-based analytical and bioanalytical sensors. There are several high impact nanozymatic sensors which reported in the literature. Although the review articles published in this field, however, the current reviews focus on the introducing nanozyme field not description on the best articles published in this filed. Hence, this article aimed to present a brief introduction on the nanozyme-based chemistry with emphasizing on the historical overview of recent nanozymatic sensors. In this regard the best nanozymatic sensors which published over 2016-2023 were briefly described and overviewed.

Monitoring the quality of stored bulk grain is generally done using temperature cables hung from silo roofs. Little investigation has been done into the effects of number of sensors and their placement in terms of reliability of the monitoring system with regard to making stored grain quality management decisions. A previously developed 3D finite element simulation model was verified and used to investigate these aspects. In the first study, a silo was loaded with about 228.6 Mg (9000 bushels) of maize and six temperature cables were placed in the grain mass. The maize was aerated continuously for a period of two weeks, and the cable sensor temperatures were compared to the predicted temperatures which were in close agreement with the observed readings. The standard error of prediction ranged from 2.0 to 3.7°C. In the second study, 15 and 30 sensors were placed at manufacturer recommended depths and horizontal locations in the grain mass of three silo sizes (i.e., 11x11, 14.6x14.6 and 14.6x18.3 m diameter by eave height). The average grain temperatures predicted by the 15 and 30 sensors over a one-year simulation period were compared to the average grain temperatures predicted for the entire grain mass (1968, 3052, and 3204 mesh nodes). The number of sensors needed to monitor stored grain temperatures reliably in the three silo sizes investigated heavily depended on whether the aeration control strategy achieved a sufficiently low temperature by the time the aeration fans were turned off and sealed ahead of the non-aerated storage period. Fifteen or 30 sensors were sufficient to monitor grain temperatures during the aeration cooling period but for the two larger silo sizes more than 30 sensors would be needed during the storage period. As silo size increased, and surface-to-volume ratio decreased, grain temperatures remained lower during the storage period. Results support the best management practice recommendation of leaving cooled grain cold and not warming it up in the spring ahead of storage into the summer.

The study of the human microbiome is a multidisciplinary area that affects from the field of technology to that of personalized medicine. The possibility of using microbiota biomarkers for the improvement in the diagnosis and monitoring of diseases (e.g. cancer), health conditions (e.g. obesity) or clinical parameters (e.g. ageing) has aroused great expectations, also in the scope of bio-electroanalytical chemistry. The well-known advantages of electrochemical transduction: high sensitivity, rapid response and possibility of miniaturization, together with the potential of new nanomaterials to improve both the design of electrode platforms and the performance of the resulting electrochemical biosensors make presumably a huge development in the next few years providing a better understanding of human microbiome entities. In this review article, the recent applications of electrochemical (bio)sensors for monitoring microbial metabolites and biomarkers of diseases related to different types of the human microbiome, with a special focus on the gastrointestinal microbiome, are reviewed. Examples of electrochemical devices applied to real samples are critically discussed as well as the challenges and prospects to be faced.

Infrared sensors are applied more and more widely in industrial production applications. Based on the theory of thermal radiation, this paper discusses the system design principle, temperature calibration method and thermal image analysis method in detail. The system has passed the measurement unit certification, showing that the field of view is 180°, the number of scanning points is 2048, the linear velocity is 10-100Hz, the spatial resolution is 2.5mrad, and the precision is ±1℃. On-line monitoring test has been done in the steelmaking plant of Bao Steel. The results show that the system has strong anti-interference ability, stability and reliability, and meets the application requirements of online monitoring.

High precision angular actuators are used for high demanding applications such as laser steering for photolithography. Piezo technology allows developing actuators with such a high resolution that the characterization of the same is out of the capabilities of commercially available instruments. At INRIM we have designed and built a device to the purpose of characterizing precision 2D angular actuators with a resolution surpassing the best devices on the market. The device is based on a multi reflection scheme that allows multiplying the deflection angle by a factor of 70. The ultimate resolution of the device is 2 prad/√Hz over a measurement range of 36 µrad with a measurement band > 10 kHz. The working principle, the practical realization and the case study on a top-level commercial angular actuator (Nano-MTA2 produced by MadCityLabs) are described.

For technical or medical applications, the knowledge of the exact kinematics of the human hand is key to utilizing its capability to handle and manipulate objects and to communicate with other humans or machines. The optimal relationship between the number of measurement parameters, measurement accuracy as well as complexity, usability and cost of the measuring systems is hard to find. Biomechanic assumptions, the concepts of a biomechatronic system and the mechatronic design process as well as commercially available components are used to develop a sensorized glove. The proposed wearable can measure 14 of 15 angular values of a simplified hand model introduced in this paper. Additionally, five contact pressure values at the fingertips and inertial data of the whole hand with a degree of freedom of six are gathered. Due to the modular design and a hand size examination based on anthropometric parameters, the concept of the wearable is applicable for a large variety of hand sizes and adaptable to different use cases. Validations show a combined root-mean-square error of 0.99° to 2.38° for the measurement of all joint angles at one finger, surpassing the human perception threshold and the current state of the art in science and technology for comparable systems.

The physical properties of nano-fertilizers (NFs) are important in determining their performance, efficacy, and environmental interactions. Nano-fertilizers, due to their small size and high surface area-to-volume ratio, enhance plant metabolic reactions, resulting in higher crop yields. The properties of nano-fertilizers depend on the synthesis methods used. The nanoparticle's nutrient use efficiency (NUE) varies among plant species. This review aims to analyze the relationship between the physical properties of NF and their influence on crop performance and nutrient uptake efficiency. The review focuses on the physical properties of NFs, specifically their size, shape, crystalline, and agglomeration. This review found that smaller particle-sized nanoparticles exhibit higher nutrient use efficiency than larger particles. Nano-fertilizer-coated additives gradually release nutrients, reducing the need for frequent application and addressing limitations associated with chemical fertilizer utilization. The shapes of nano-fertilizers have varying effects on the overall performance of plants. The crystalline structure of nanoparticles promotes a slow release of nutrients. Amorphous nano-fertilizers improve the NUE and, ultimately, crop yield. Agglomeration results in nanoparticles losing their nanoscale size, accumulating on the outer surface, and becoming unavailable to plants. Understanding the physical properties of nano-fertilizers is crucial for optimizing their performance in agricultural applications.

The refractive index of a liquid serves as a fundamental parameter reflecting its composition, thereby enabling the determination of component concentrations in various fields such as chemical research, food industry, and environmental monitoring. Traditional methods for refractive index (RI) measurement rely on light deflection angles at interfaces between the liquid and a material of known refractive index. In this paper, the authors present a new differential refractometer for highly sensitive measurement of RI differences between two liquid samples. Using a configuration with two cells equipped with flat parallel plates as measuring elements, the instrument facilitates accurate analysis. Namely, the sensor signals from both the solution and the solvent cuvette are generated simultaneously with one laser pulse, reducing the possible fluctuations of the laser radiation intensity. Our evaluation shows the high sensitivity of RI measurements (< 7 · 106), so this differential refractometer can be proposed not only as a high-sensitivity sensing tool that can be used for mobile detection of nanoparticles in solution samples, but also to determine the level of environmental nano-pollution using water (including rain, snow) samples from various natural as well as industrial sources, thus helping to solve some important environmental problems.

In this computational study, we investigate the electronic properties of zigzag graphene nano-parallelograms (GNPs), which are parallelogram-shaped graphene nanoribbons of various widths and lengths, using thermally-assisted-occupation density functional theory (TAO-DFT). Our calculations reveal a monotonic decrease in the singlet-triplet energy gap as the GNP length increases. The GNPs possess singlet ground states for all the cases examined. With the increase of GNP length, the vertical ionization potential and fundamental gap decrease monotonically, while the vertical electron affinity increases monotonically. Besides, as the GNP length increases, the symmetrized von Neumann entropy increases monotonically, denoting an increase in the degree of multi-reference character associated with ground-state GNPs. The occupation numbers and real-space representation of active orbitals indicate that there is a transition from the nonradical nature of the shorter GNPs to the increasing polyradical nature of the longer GNPs. In addition, the edge/corner localization of active orbitals is found for the wider and longer GNPs.

Anthocyanins (ACNs) have attracted considerable attention for their potential to modulate the immune system. Research has revealed their antioxidant and anti-inflammatory properties, which play a crucial role in immune regulation by influencing key immune cells such as lymphocytes, macrophages, and dendritic cells. Moreover, ACNs contribute to maintaining a balance between proinflammatory and anti-inflammatory cytokines, thus promoting immune health. Beyond their direct effects on immune cells, ACNs significantly impact gut health and the microbiota, essential factors in immune regulation. Emerging evidence suggests that they positively influence the composition of the gut microbiome that enhance the immunomodulatory effects of ACNs. Furthermore, these compounds synergize with other bioactive substances, such as vitamins and minerals, further enhancing their potential as immune-supporting dietary supplements. However, detailed clinical studies must fully validate these findings and determine safe dosages for different populations. Incorporating these natural compounds into functional foods or supplements can revolutionize the management of immune-related conditions. Personalized nutrition and healthcare strategies can be developed to enhance overall well-being and immune resilience by fully understanding the mechanisms underlying their actions. Recent advancements in delivery methods have focused on improving the bioavailability and effectiveness of ACNs, providing promising avenues for future applications.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

In order to effectively utilize red mud, an aluminum industrial waste, the stabilized soil material was developed using nano-SiO2 synergistically modified red mud, and the strength characteristics of the stabilized soil were analyzed to clarify the feasibility of such stabilized soil serves as a road base material. Through different combination schemes, the effects of different nano-SiO2 and cement contents on the strength of the stabilized materials were explored. The test results show that: in the synergistic modification of nano-SiO2 and cement, nano-SiO2 can significantly improve the early unconfined compressive strength of red mud-based stabilized soil; in the synergistic modification of nano-SiO2, gypsum and cement, the 7-d unconfined compressive strength of red mud-based stabilized soil is greater than 2 MPa, which meets the strength requirements of road base materials and shows the superiority of synergism. The nominal stress-strain curves are divided into five stages: compressed and compacted stage, elastic deformation stage, plastic deformation stage, damage deformation stage and residual deformation stage. The macroscopic compressive damage pattern of the specimens shows that the modified red mud-based stabilized soil mostly exhibits brittle damage.

In order to effectively utilize red mud and reduce its occupation of land resources as well as its impact on the environment, experiments were conducted to develop stabilized soil materials using nano-SiO2 synergistically modified red mud and to investigate the curing mechanism of stabilized soil. The unconfined compressive strength, microscopic morphology and curing mechanism of the red mud-based stabilized soil materials with different amounts of modified materials were investigated. The test results show that after 7-days curing, the unconfined compressive strength of red mud-based stabilized soil meets the compressive strength requirement of road base material when nano-SiO2, gypsum and cement are synergistically modified. In such case, the soil structure has the lowest fracture rate and the best structural compactness when the amount of nano-SiO2 is 1%; It is found that the needle-like and columnar calcium alumina in the modified red mud-based stabilized soil increases, and the binding energy of hydration product ions in the modified material is improved; The chemical curing mechanism of modified red mud-based stabilized soil includes hydration reaction, volcanic ash reaction, promotion effect of nano-SiO2, and enhancement effect of gypsum. On this base, a model of early start hydration process of red mud-based stabilized soil promoted by nano-SiO2 is established.

In recent years, graphene has received so much attention because of its superlative properties and its potential to revolutionize electronics especially in VLSI. This study analyzes the effect of single event upset (SEU) in SRAM cell which employs metal-oxide semiconductor type graphene nano-ribbon field effect transistor (MOS-GNRFET) and compares the results respectively with another SRAM cell designed in PTM 10nm FinFET node. Our simulation show there is a change in data stored in the SRAM after heavy ion strike. However, it recovers from radiation effects after 0.46 ns for GNRFET and 0.51 ns for FinFET. Since the degradation observed in Q and Qb of GNRFET SRAM are 2.7X and 2.16X as compared to PTM nano-MOSFET, we can conclude that GNRFET is less robust to single effect upset. In addition, the stability of SRAM can be improved by increasing the supply voltage VDD.

Lipid nanoparticles have an interesting part of drug delivery system. In this study, the modification of the convention nano-lipid based soybean lecithin was demonstrated. Ginger oil derived Zingiber officinale was used along with lecithin, cholesterol and span 80 to fabricate nano-lipid (GL nano-lipid) using thin-film method. Through TEM and confocal microscope, GL nano-lipid exposes the liposome- like morphology. The average size of the resultant nanoparticles was 249.1nm with monodistribution (PDI= 0.021). The ζ-potential of GL nano-lipid was negative as similar to as prepared nano-lipid based lecithin. GL nano-lipid express the highly stable over 60 days of storage at room temperature in term of size, ζ-potential. A shift of pH value from alkaline to acid was detected in lecithin nano-lipid, while with the incorporation of ginger oil, pH value of nano-lipid dispersion was around 7.0. Furthermore, due to the rich of shogaol-6 and other active compounds in ginger oil, the GL nano-lipid is endowed with intrinsic antibacterial feature. In addition, the sulforhodamine B (SRB) assay and live/dead imaging revealed the excellent biocompatibility of GL nano-lipid. Notably, GL nano-lipid was capable to carry the hydrophobic agents as curcumin and perform a pH-dependent release profile. A subsequent characterization are a suitable potential for drug delivery system.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

In this paper, the far field and near field optical responses of a gold nanoparticle are studied and simulated numerically. The electromagnetic field was excited by an electric dipole located near one end of the nanorod, which is used to model the emission of a quantum dot. Another excitation method was also simulated in which an incident plane wave is used. The excitation of dark plasmon modes of the gold nanorod is presented. The Poynting equation was solved numerically to study the influence of the gold nanorod on the dipole radiative power. In addition, the extinction cross section of the gold nanoparticle illuminated by the incident plane wave was calculated to estimate the amount of the scattered and absorbed light.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

Hybrid inorganic-polymer nanocomposites can be employed in diverse applications due to the potential combination of desired properties from both the organic and inorganic components. The use of novel bottom-up in situ synthesis methods for the fabrication of these nanocomposites is advantageous compared to top-down ex situ mixing methods, as it offers increased control over the structure and properties of the material. In this review, the focus will be on the application of the sol-gel process for the synthesis of inorganic oxide nanoparticles in epoxy and polysiloxane matrices. The effect of the synthesis conditions and the reactants used on the inorganic structures formed, the interactions between the polymer chains and the inorganic nanoparticles, and the resulting properties of the nanocomposites are appraised from several studies over the last two decades. Lastly, alternative in situ techniques and the applications of various polymer-inorganic oxide nanocomposites are briefly discussed.

Recent progress in the fabricating flexible electronics has been developed significantly due to the increased interest of the flexible electronics which can be applied to enormous fields not only to conventional electronic devices but to bio/eco electronic devices. Flexible electronics can be applied to wide range of fields such as flexible display, flexible power storage, flexible solar cells, wearable electronics and healthcare monitoring devices. Recently, flexible electronics are being attached on the skin and even implanted into human body to monitor the bio-signals and for treatment purpose. To improve the electrical characteristic and the mechanical properties of flexible electronics, nanoscale fabrications using novel nano-materials are required. Advanced in nanoscale fabrication methods allow construction of the active materials that can combine with the ultra-thin soft substrate to form flexible electronics with high performances and reliability. In this review, wide range of nanoscale fabrication methods for flexible electronics classified in either top-down or bottom-up approaches such as conventional photolithography, soft lithography, nanoimprint lithography, growth, assembly and chemical vapor deposition(CVD) will be reported with specific fabrication processes and results. Here, our aim is to introduce various fabrication methods that can be used to fabricate the flexible electronics.

The development of high-performance hydrogen peroxide (H2O2) sensors is critical for various applications, including environmental monitoring, industrial processes, and biomedical diagnostics. This study explores the development of efficient and selective H2O2 sensors based on bismuth oxide/bismuth oxyselenide (Bi2O3/Bi2O2Se) nanocomposites. The Bi2O3/Bi2O2Se nanocomposites were synthesized using a simple solution-processing method at room temperature, resulting in a unique heterostructure with remarkable electrocatalytic properties for H2O2 detection. Characterization techniques, including powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM), confirmed the successful formation of the nanocomposites and their structural integrity. The synthesis time was varied to obtain the composites with different Se content. Electrochemical measurements revealed that the Bi2O3/Bi2O2Se composite formed under optimal synthesis conditions displayed high sensitivity (152.7 µA µM-1 cm-2) and excellent selectivity towards H2O2 detection, along with a wide linear detection range (0.02 - 15 µM) and low detection limit (1.62 µM). The superior performance is attributed to the synergistic effect between Bi2O3 and Bi2O2Se, enhancing electron transfer and creating more active sites for H2O2 oxidation. These findings suggest that Bi2O3/Bi2O2Se nanocomposites hold great potential as advanced H2O2 sensors for practical applications.

In recent years, there has been an increase in the number of illegal radio stations that exceed power limits or use illegal frequencies. There has been a radio monitoring system called the DEURAS system to control these illegal radio stations. This system monitors illegal radio stations by receiving illegal radio waves using sensor stations installed in various locations. However, these systems sometimes do not work well when there is no line of sight from the sensor stations to the illegal radio stations or when there are many reflected waves generated due to the surrounding environment. In this study, we proposed a radio wave source estimation using HAPS, an unmanned aerial vehicle flying at high altitude. The simulation results show that estimation from high altitude provides higher estimation probability and estimation accuracy than the conventional method.

The main purpose of this study was to create a prototype of an unmanned aerial system equipped with intelligent hardware and software technologies necessary for monitoring the health and growth of crops in orchards. Another important objective was to use low-cost sensors that accurately measure ultraviolet solar radiation. The device, which needs to be attached to the commercial DJI Mini 4 Pro drone, should be small in size, portable, and have very low energy consumption. For this purpose, the widely used Vishay VEML6075 digital optical sensor was selected and implemented in a prototype, alongside a Raspberry Pi Zero 2W minicomputer. To collect data from these sensors, a program written in Python was used, containing specific blocks for data acquisition from each sensor, to facilitate the monitoring of ultraviolet (UV) radiation, or battery current. By analyzing the data obtained from the sensors, several important conclusions are drawn that may provide valuable pathways for the further development of mobile or modular equipment. Furthermore, the results of the plant condition analysis with proposed models in the Geographic Information System (GIS) environment were also presented. The visualization of maps indicating variations in vegetation condition led to the identification of problem areas like hydric stress.

One of the important issues being explored in Industry 4.0 is a collaborative mobile robots. This collaboration requires precise navigation systems, especially indoor navigation systems where GNSS (Global Navigation Satellite System) cannot be used. To enable precise localization of robots, different variations of navigation systems are being developed, mainly based on trilateration and triangulation methods. Triangulation systems are distinguished by the fact that they allow precise determination of an object’s orientation, which is important for mobile robots. An important feature of positioning systems is the frequency of position updates based on measurements. For most systems it is 10-20 Hz. In our work, we propose a high-speed 50 Hz positioning system based on the triangulation method with infrared transmitters and receivers. In addition, our system is completely static, i.e. it has no moving/rotating measurement sensors, which makes it more resistant to disturbances (caused by vibrations, wear and tear of components, etc.). In this paper we describe the principle of the system as well as its design. Finally, we present tests of the built system, which show centimeter positioning accuracy with a position update frequency of 50 Hz.

Studies at the molecular, systemic, and epidemiological levels have shown that chronic metal exposure is linked to significant health consequences, including cancer, affecting hundreds of millions worldwide. Subtle and convoluted mechanisms underline metals' toxicity and carcinogenicity. The use of sensors for carcinogenic metals' trace detection is on the rise due to their selectivity, simplicity, and affordability. Biotechnology and microelectronics in the development of sensors have grown complementarily in recent years. This study offers a comprehensive overview of current research and advancements in developing sensors for detecting carcinogenic metals. Here, we have focussed on the developed biosensor platforms for group 1 carcinogens, i.e., arsenic, nickel, cadmium, chromium, and beryllium, along with their brief roles in human carcinogenesis. This review also looks at the importance of sensing such metal exposure in humans from a larger perspective, hoping to influence future research toward early prevention and treatment of illnesses like cancer.

Telemonitoring and telerehabilitation have shown promise in delivering individualized healthcare remotely. We introduce STASISM, a Sensor-Based Telerehabilitation and Telemonitoring System, in this work. This platform has been created to facilitate individualized telerehabilitation and telemonitoring for those who need rehabilitation or ongoing monitoring. To gather and analyze pertinent and validated physiological, kinematic, and environmental data, the system combines a variety of sensors and data analytic methodologies. The platform facilitates customized rehabilitation activities based on individual needs, allows for remote monitoring of patients' progress, and offers real-time feedback. To protect the security of patient data and to safeguard patient privacy, STASISM also provides secure data transmission and storage. The platform has the potential to significantly improve the accessibility and efficacy of telerehabilitation and telemonitoring programs, enhancing patients' quality of life and allowing healthcare professionals to provide individualized care outside of traditional clinical settings/

The production of high-quality wines is one of the primary goals of modern oenology. In this regard, it is known that the potential quality of a wine begins to be determined in the vineyard, where the quality of the grape, initially, and later that of the wine, will be influenced by the soil properties. Given the spatial variability of the fundamental soil properties related to the potential grape production, such as texture, soil organic matter content, or cation exchange capacity, it seems that a uniform management of a vineyard is not the most optimal way to achieve higher grape quality. In this sense, the delineation of zones with similar soil characteristics to implement site-specific management is essential, reinforcing the interest to incorporate technologies and methods to determine these homogeneous zones. A case study was conducted in a 3.3 ha vineyard located near Évora, South of Portugal. A non-contact sensor (DUALEM 1S) was used to measure soil apparent electrical conductivity (ECa) in the vineyard, and later, a kriged ECa map was generated. ECa and elevation maps were utilised to delineate homogeneous zones (management zones, MZs) in the field through a clustering process. MZs were validated using some soil properties (texture, pH, organic matter -OM, phosphorous -P2O5, potassium -K2O, sum of the exchange bases -SEB; and cation exchange capacity -CEC) which were determined from 20 soil samples taken in the different MZs. Additionally, validation was also performed using Rasch measures, which were defined based on the formula-tion of the objective and probabilistic Rasch model, integrating the information from the afore-mentioned soil properties at each sampling location. The comparison of the MZs was more evident with the use of the Rasch model, as only one value was to be employed in each MZ. The use of ECa constitutes an efficient technological tool for implementing site-specific man-agement in viticulture, which allows for the improvement of decision-making processes by con-sidering the inherent spatial variability of the soil.

The process industry is confronted with rising demands for flexibility and efficiency. One way to achieve this are modular process plants that consist of pre-manufactured modules with their own decentralized intelligence. Plants are then composed of these modules as unchangeable building blocks and can be easily re-configured for different products. Condition monitoring of such plants is necessary, but available solutions are not applicable. The authors suggest an approach in which model-based symptoms are derived from few measurements and observers that are based on manufacturer knowledge. The comparisons of redundant observers lead to residuals that are classified to obtain symptoms. These symptoms can be communicated to the plant control and are inputs to an easily adaptable diagnosis. The implementation and validation at a modular mixing plant showcases the feasibility and the potential of this approach.

: Microbial fuel cell (MFCs) devices utilise the metabolic processes of bacteria to generate electricity from various organic substrates. Due to the enormous amount of energy that organic waste produces, scientists are highly interested in advanced MFCs. MFCs serve as a multidisciplinary research platform at the engineering and natural sciences intersection. MFCs have various uses besides being used as energy sources, such as sensing capabilities. Despite showing considerable promise, only a few marine sediment MFCs have been deployed in real-world applications to supply current for low-power devices. It is now required to maintain track of the work being done by research groups worldwide and regularly compile significant discoveries due to the rising quantity of research publications. Review papers are a traditional beginning point for a literature review for new scholars. This review is a fast reckoner that directs readers to pertinent reviews and research publications detailing significant advances in microbial fuel cell research during the previous two decades. An overview of key advances in MFC research over the past two decades is provided as a quick reference in this review article. In addition, the report identifies research gaps that, if filled, could bring this technology closer to real-world use.

Over the past decade, Deep Learning (DL) had been applied in a large number of optical sensors’ applications. DL algorithms can improve the accuracy and reduce the noise level in optical sensors. Optical sensors are considered as promise technology for the modern intelligent sensing platforms. These sensors are widely used to process monitoring, quality prediction, pollution, defense, security and many other applications. However, they suffer major challenges such as the large generated data and low processing speed for that data and moreover the much cost of these sensor. These challenges can be mitigated by integrating deep learning system with the optical sensor technologies. This paper presents recent studies that integrate DL algorithms with optical sensors applications. This paper also highlights several of DL algorithms directions that promise a considerable impact on use for optical sensor applications. Moreover, this study provides new directions for the future related research development.

A sensitive electrochemical sensor based on AuPtPd trimetallic nanoparticles functionalized multi-walled carbon nanotubes coupled with chitosan modified glassy carbon electrode (GCE/CS/MWCNTs-AuPtPd) for the rapid detection of bisphenol A (BPA) was proposed. AuPtPd trimetallic nanoparticles were first assembled on MWCNTs to obtain MWCNTs-AuPtPd nanocomposite. Then the MWCNTs-AuPtPd was further dispersed on the surface of chitosan modified electrode surface to fabricate the GCE/CS/MWCNTs-AuPtPd sensor. Due to the superior catalytic properties of MWCNTs-AuPtPd and the good film formation of chitosan, the constructed sensor displayed good performances for BPA detection. The structural morphology of CS/MWCNTs-AuPtPd was characterized by many methods, such as SEM, UV-vis and TEM. Under the optimal conditions, the designed sensor showed a linear range from 0.05 to 100 µM for BPA detecting with a low detection limit of 1.4 nM. The designed sensor was further used to realize the determination of BPA in real samples and the recoveries ranged from 94.4% to 103.6%. The results demonstrated that the electrochemical sensor designed by CS/MWCNTs-AuPtPd nanocomposites was reliable and could be a useful tool for the monitoring of food safety.

The fourth industrial revolution, also known as Industry 4.0, has led to an increased transition towards automation and reliance on data-driven innovations and strategies. Companies in the manufacturing sector are heavily integrating Industry 4.0 technologies, including cloud compu-ting, cyber-physical systems (CPS), big data analytics, horizontal and vertical system integration, the internet of things (IoT), and additive manufacturing (3d printing). The interconnected systems and processes have significantly increased operational efficiency, enhanced organizational capacity to monitor and control functions, reduced costs, and improved product quality. One significant way that companies have achieved these benefits is by integrating diverse sensor technologies within these innovations, allowing critical data collection on products, equipment performance, and maintenance. The sensors connect systems and machines, allowing them to communicate and track operations for enhanced operations. While numerous research has been conducted to show the role of sensors in industry 4.0, limited studies show how these innovations can leverage product design to maximize benefits and opportunities. Given the rapidly changing market conditions, Industry 4.0 requires new products and business models to ensure companies adjust to the current and future changes. These requirements call for the evolutions in product design processes to accommodate design features and principles applicable in the current dynamic business environment. This research paper employs a systematic bibliometric literature review (LRSB) methodology to explore and synthesize data on how Industry 4.0 and sensors can leverage product design. The results show that various product design features create opportunities to be leveraged to guarantee the success of Industry 4.0 and sensor technologies. However, the research also identifies numerous challenges that undermine the ongoing transition towards intelligent factories and products.

The article presents the stages of modeling and simulation of a new design of a wheelchair with the option of moving up and down stairs. These analyzes were aimed at the synthesis of the de-sign parameters and parameters of the sensor and control systems. The simulation results were verified by experimentally testing the prototype.

Currently, large volumes of data are being collected on farms using multimodal sensor technol-ogies. These sensors measure the activity, housing conditions, feed intake, and health of farm animals. With traditional methods, the data from farm animals and their environment can be collected intermittently. However, with the advancement of wearable and non-invasive sensing tools, these measurements can be made in real-time for continuous quantitation relating to clinical biomarkers, resilience indicators, and behavioral predictors. The digital phenotyping of humans has drawn enormous attention recently due to its medical significance, but much research is still needed for the digital phenotyping of farm animals. Implications from human studies show great promise for the application of digital phenotyping technology in modern livestock farming, but these technologies must be directly applied to animals to understand their true capacities. Due to species-specific traits, certain technologies required to assess phenotypes need to be tailored ef-ficiently and accurately. Such devices allow for the collection of information that can better inform farmers on aspects of animal welfare and production that need improvement. By explicitly ad-dressing farm animals’ individual physiological and mental (affective states) needs, sensor-based digital phenotyping has the potential to serve as an effective intervention platform. Future re-search is warranted for the design and development of digital phenotyping technology platforms that create shared data standards, metrics, and repositories.

The purpose of this paper is to present advanced techniques in optical biodevices. Moreover different configurations involving the generation of fiber optical biosensors are described. To overcome some limitations of fiber optical biosensors, plasmonic phenomena proposed. In addition novel plasmonic phenomena have broaden researcher’s horizons in new discovering in terms of technology and application. As regards there are many challenges to detect ultra-low concentration samples with high sensitivity in real time. Researchers have always made great efforts to discover more effective methods. Throughout the paper SPR and LSPR as a powerful analysis instrument are introduced. Finally surveys the current practical performances of plasmonic sensors in detection of bio target are provided. As a result these devices demonstrate great potential in identifying target analytic due to their unique optical biosensors.

Since it was proposed, the Robot Operating System (ROS) has fostered solutions for various problems in robotics in the form of ROS packages. One of these problems is Simultaneous Localization and Mapping (SLAM), a problem solved by computing the robot pose and a map of its environment of operation at the same time. The increasingly availability of robot kits ready to be programmed and also of RGB-D sensors often pose the question of which SLAM package should be used given the application requirements. When the SLAM subsystem must deliver estimates for robot navigation, as is the case of applications involving autonomous navigation, this question is even more relevant. This work introduces an experimental analysis of GMapping and RTAB-Map, two ROS compatible SLAM packages, regarding their SLAM accuracy, quality of produced maps and use of produced maps in navigation tasks. Our analysis aims ground robots equipped with RGB-D sensors for indoor environments and is supported by experiments conducted on datasets from simulation, benchmarks and from our own robot.

A method for infrared and cameras sensor fusion, applied to indoor positioning in intelligent spaces, is proposed in this work. The fused position is obtained with a maximum likelihood estimator from infrared and camera independent observations. Specific models are proposed for variance propagation from infrared and camera observations (phase shifts and image respectively) to their respective position estimates and to the final fused estimation. Model simulations are compared with real measurements in a setup designed to validate the system. The difference between theoretical prediction and real measurements is between 0.4 cm (fusion) and 2.5 cm (camera), within a 95% confidence margin. The positioning precision is in the cm level (sub-cm level can be achieved at most tested positions) in a 4x3 m locating cell with 5 infrared detectors on the ceiling and one single camera, at distances from target up to 5 m and 7 m respectively. Due to the low cost system design and the results observed, the system is expected to be feasible and scalable to large real spaces.

In this research paper we describe the development phase of a low-cost LoRa IoT solution applied to a kindergarten school with three years results. A set of sensors solution was developed in a LoRa communication board, battery powered, providing a simplified setup process. These sensors were used in order to measure temperature, humidity, luminosity, air quality and presence. Also, energy monitor solutions were integrated. The acquired data is transmitted and analysed for knowledge extraction, identifying savings and other related KPIs. From data, automatic saving actions were performed towards heating and cooling systems, lighting and a set of if-then actions were developed for automatic cost-saving actions, based on infrared signals to heating/cooling systems using some procedure of external command devices. This approach avoids the usage of proprietary vendor solutions in a flexible approach that can easily be deployed to any building facility. This is an important achievement since most of the building consumption is based on heating and cooling systems. In a three years test of the solution, the total energy consumption savings surpassed 20%

We present an integrable, sensor inlay for monitoring crack initiation and growth inside bondlines of structural carbon fiber reinforced plastic (CFRP) components. The sensing structures are sandwiched between crack stopping polyvinyliden fluoride (PVDF) and a thin reinforcing polyetherimide (PEI) layer. Good adhesion at all interfaces of the sensor system and to the CFRP material is crucial as weak bonds can counteract the desired crack stopping functionality. At the same time, the chosen reinforcing layer must withstand high strains, safely support the metallic measuring grids and possess outstanding fatigue strength. We show that this robust sensor system, which measures the strain at two successive fronts inside the bondline, allows to recognize cracks in the proximity of the inlay regardless of the mechanical loads. Feasibility is demonstrated by static load tests as well as cyclic long-term fatigue testing with up to 1,000,000 cycles. In addition to pure crack detection, crack distance estimation based on sensor signals is illustrated. The inlay integration process is developed with respect to industrial applicability. Thus, implementation of the proposed system will allow the potential of lightweight CFRP constructions to be better exploited by expanding the possibilities of structural adhesive bonding.

The use of New-age (Nano) Modified Emulsions (NME) for the stabilisation of marginal materials for use in the upper-pavement layers of roads have been proven in laboratories, through Accelerated Pavement Tests (APT) and in practice. In addition, material design methods have been developed based on the scientific analysis of granular material mineralogy and the chemical interaction with the binder to design a material compatible NME stabilising agent for naturally available (often marginal) materials. However, the introduction of any new disruptive technology in a traditionally well-established industry, such as the road construction industry, is usually associated with considerable resistance. This is especially relevant when the new technology enables the use of granular materials traditionally considered to be of an unacceptable quality in combination with relatively new concepts such as New-age (Nano) Modified Emulsions (NME). In practice, few road construction projects are without any problems. The introduction of new-technologies obviously makes it an easy target to blame for any non-related problem that may arise during construction. This article aims to assist in pre-empting, recognising, preventing and resolving material or non-material related construction problems through the correct identification of the cause of the problem and recommending the best, most cost-effective way to correct any deficiencies on site.

Side-chain liquid crystal polymers have been mixed with ferromagnetic particles, and the for-mation of a monodomain in magnetic fields studied. At relatively low concentrations, the presence of ferroparticles substantially speeds up the rate of formation of a monodomain with the magnetic field and at a given concentration of ferrofluid that rate is independent of the magnetic field strength. In this way, rapid formation of a monodomain is possible at magnetic field strengths far lower than required for the liquid crystal polymer alone. This is anticipated to very helpful in the fabrication of devices based on monodomain liquid crystal elastomers. Wide angle x-ray scattering has been used to monitor the formation of the monodomain and small angle x-ray scattering can give some indication of the ferroparticle behaviour. A model is developed to explain the behaviour. The alignment properties of the ferroparticles is related to their ability to form chains under the influence of very low magnetic fields; these chains are of relatively low stability and may become disrupted after long times, high magnetic fields, or high concentrations. In general, the best results for alignment were at volume fractions below 1%, and under these con-ditions there is the potential for producing monodomain samples with improved properties; in particular shape changes with temperature are significantly larger as a result of improved backbone orientation. Experiments involving monodomain formation and director realignment suggest that the presence of ferroparticles results in a modification in the mechanism for alignment development driven by the organisation of the polymer backbone as a consequence of the con-straints offered by the morphology of the chains of ferroparticles.

Bacillus Calmette-Guérin (BCG) immunotherapy has been a cornerstone treatment for non-muscle invasive bladder cancer for decades and still faces challenges, such as severe immune adverse reactions, which reduce its use as a first-line treatment. This review examines BCG therapy’s history, mechanisms, and current status, highlighting how nanotechnology and bioengineering are revitalizing its application. We discuss novel nanocarrier systems aimed at enhancing BCG's efficacy while mitigating specific side effects. These approaches promise improved tumor targeting, better drug loading, and enhanced stimulation of anti-tumor immune responses. Key strategies involve using functional BCG cell wall components and co-delivering BCG with chemotherapeutics to achieve synergistic effects. While most studies remain experimental, this research direction offers hope for overcoming BCG's limitations and advancing bladder cancer immunotherapy. Further elucidation of BCG's mechanisms and rigorous safety evaluations of new delivery systems will be crucial for translating these innovations into clinical practice.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

The application of dry lubrication in rolling contacts is challenging due to wear. In previous studies graphene platelets applied as dry lubricants on the surfaces of angular contact ball bearings demonstrated superior properties. These specific bearings, experiencing both rolling and spinning motion, create more severe conditions for dry lubricants. The applied graphene platelets have a thickness of few graphene layers in the nm range and a diameter in the µm range. Such platelets can be produced by mechanical exfoliation from graphite. To delve deeper into the lubrication effects, investigations were carried out using a milli tribometer. In the tests, a fixed steel ball is sliding against an oscillating counterpart under defined load. During the measurements, the applied load and tangential forces on the ball are recorded to calculate the friction. In our case, a steel ball with a diameter of 6 mm was used against graphene-based films on flat bearing surfaces (axial bearing washer). Comparative investigations included nano graphite particles and fullerene as dry lubricants, in addition to graphene platelets of various staple thicknesses. To increase the adhesion of the films to the surfaces, a pre-rolling process was implemented. Afterwards, the friction on the compressed films was measured. The results indicate that the pre-rolling process effectively reduces the friction of the system. After testing, the surfaces underwent analysis using laser scanning microscopy to assess the formed films, wear, and material transfer. It has been demonstrated that the pre-rolling process leads to the formation of a very thin compacted film with surface protective properties. On the ball as counterpart, the graphene platelets generate a transfer film on the contacting surface.

Soil salinity is seen as a major restriction for crop production, and with water scarcity this problem becomes more complicated. Mulching is crucial to salinity dynamics management by decreasing evaporation with improving the soil’s characteristics. Using chitosan as an eco-friendly biostimulant can enhance plant defense genes during different abiotic stresses. Recently, agricultural research has recognized nanoparticles as a pioneer material due to their distinctive physicochemical features. Therefore, a lysimeter experiment was conducted to investigate the interactive effects of mulching (UNM: un-mulched, WPM: white plastic, RSM: rice straw and SDM: sawdust) and chitosan foliar application (Ch0: control, Ch1: 250 mg chitosan L-1, Ch2: 125 mg nano chitosan L-1, and Ch3: 62.5 mg nano chitosan L-1) on the biochemical soil characteristics and common beans productivity under salt affected soil conditions. Organic mulching (RSM and SDM) treatments significantly improved the soil's organic carbon, available nutrient content, and total count of bacteria. WPM treatment lowered soil EC to 6.63 dS m-1 and increased soil water content to 34.13%. The application of Ch3 caused considerable increases in the plant height, shoot dry weight, root dry weight, grain yield, and nutrient content in the seed. The total fungi count in the soil and Na% in the seed was significantly decreased due to chitosan foliar applications. Moreover, the interactive effect of different mulch materials plus foliar by chitosan applications gave a statistically similar seed yield in both seasons. Overall, this study revealed the potential of the mulching treatments and foliar application of nano chitosan in improved biochemical soil characteristics and common bean productivity under saline soil conditions.

In this paper we introduce the concept of Nano Beta Closure, Nano Beta Interior and study the relationship between them also study some of their properties. Based on these notions we introduced the topological Approach to Decision Making and Its Application in the Medical Field" which describes the use of topological methods in decision-making, specifically through the utilization of nano beta closure and nano beta interior. These mathematical tools are applied in the medical field to improve diagnostic accuracy and aid in treatment planning. The authors demonstrate the effectiveness of this approach through a case study on the diagnosis of Chronic Kidney. The results show that the topological approach using nano beta closure and nano beta interior provides a reliable and accurate method for medical decision-making. Finally, we introduce a medical application for disease groups patients of with chronic kidney. To identify the main causative agent of kidney disease. where using this approach, the medical team can identify the specific areas of the kidney that are affected by the infection, as well as the extent of damage and any potential complications. This information is used to create an individualized treatment strategy that is customized to meet the specific requirements of the patient. and medical history. We write an algorithm that can be a helpful tool for doctors to utilize in diagnosing infection disease Chronic Kidney infections. By utilizing this approach, clinicians can provide accurate diagnoses, develop effective treatment plans, and ultimately improve patient outcomes. finally, we show that fractals hold significant importance in future nano topological generation of the human factor. Their unique properties and self-similar patterns offer insights into the complex organization of biological systems and provide a foundation for designing advanced Nanosystems.

Diabetes mellitus is a cluster of metabolic diseases characterized by hyperglycemia. Since this epidemic growing worldwide, the usage of phototherapeutics to manage diabetes is vital. Coccinia grandis (Aka ivy gourd) belongs to cucumber family is identified as a most effective herb, especially for diabetes and many other disease conditions. Hence, an instant herbal porridge cube incorporating Coccinia grandis leaf powder was produced and sensory acceptability of the porridge was evaluated using trained panelists. The bioactive activity of Coccinia grandis leaf powder showed that 66.77±0.74 mg/g GAE of Total Phenolic Content, 27.65±6.79% of DPPH radical scavenging activity, 5.72% of alpha-amylase inhibition activity and 59.64% of alpha-glucosidase inhibition activity. The effect on postprandial blood sugar levels after consuming the developed porridge was measured using healthy adults and it was observed there was no blood sugar elevation during the 2 hours of time. As a further development, Coccinia grandis leaf extract was nano-encapsulated with food grade Sodium alginate and it was incorporated into the same porridge as a safe delivery method of bioactive compounds. In-vitro digestion assay was conducted and the results show that alpha-amylase inhibition activity for the gastric phase and alpha-glucosidase inhibition activity for the intestinal phase was higher in nano-encapsulated porridge. The study concludes that, consuming nano-encapsulated Coccinia grandis leaf extract with porridge is more beneficial for diabetic patients.

Organophilic nano clay is the composition of mostly clay and organic molecules designed to improve various materials' physical and chemical properties. Permanent deformation in asphalt pavements is primarily the result of inadequate compaction, excessive loading, and high temperatures. Rutting can result in aquaplaning, leading to accidents and costly maintenance and rehabilitation works that drain the economy. Such behavior of asphalt pavements may be attributable to poor selection of aggregate, asphalt binder, or substandard asphalt binders. This study used different percentages of organophilic nano clay ranging from 3.0% - 5.0% with two penetration grade bitumen, i.e., N.R.L 60-70 &amp; N.R.L 80-100. Adding organophilic nano clay to asphalt binder significantly reduced the rutting potential under cyclic loading at high temperatures (55 °C). Ten modified formulations and two virgin bitumen specimens were prepared. The modified binders' viscosity and rutting were tested using the Rotational Viscometer and Wheel Tracker Test (W.T.T.), respectively. The results were analyzed using software for Statistical Analysis. It was recorded that organophilic nano clay-modified bitumen significantly affected rutting to interpret the results. The results indicated that rutting decreased and viscosity increased in all nano clay-modified bitumen samples, with a 4.5% O.N.C modified binder showing the most significant improvement.

The present work is focused on functionalizing Montmorillonite (Mt) with poly dimethyl siloxane (PDMS) to develop a hybrid membrane reactor for the removal of Co (II) and Ni (II) ions from model wastewater samples. The specific surface area of the novel material was found to be 444 m2 /g. X-Ray Diffraction (XRD) and Fourier Transform Infra-Red (FTIR) spectra reveal the formation of exfoliated composite material. The efficiency of this membrane material was determined by subjecting it to continuous filtration experiments. It was able to remove 50% of Co (II) and 75% of Ni (II) ions, respectively, in one cycle of filtration in less than three minutes of operation with a permeate flux rate of 675 L/m2/H and 975 L/m2/H respectively, for both the ions.

This work presents the production and incorporation of calcium hydrolyzed nano-solutions at three concentrations (1, 2, and 3 wt.%) in alkali-activated gold mine tailings (MTs) from Arequipa, Perú. A first activator solution of sodium hydroxide (NaOH) at 10M was used. The calcium hy-drolyzed nano-solutions acted as a secondary activator and as additional calcium resource for the alkali-activated materials (AAMs) based on the low-calcium gold MTs. High-resolution trans-mission electron microscopy/energy-dispersive x-ray spectroscopy (HR-TEM/EDS) analyses were carried out to characterize the morphology, size, and structures of the calcium hydrolyzed na-noparticles. Fourier transform infrared (FTIR) analyses then were used to understand the chemical bonding interactions in the calcium hydrolyzed nanoparticles and in the AAMs. Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS) and Quantitative X-ray diffraction (QXRD) were performed to study the structural, chemical, and phase compositions of the AAMs; uniaxial compressive tests evaluated the compressive strength of the reacted AAMs; and Nitrogen adsorption-desorption analyses measured the porosity changes at nanostructure level in the AAMs. The results indicate that each increase in the concentration of the calcium hydrolyzed nano-solution had a direct/proportional effect on the mechanical properties of the AAMs samples. The AAMs with 3 wt.% calcium-hydrolyzed nano-solution had the highest compressive strength value of 15.16 MPa, which represented an increase of 62% compared to the original system without nanoparticles and aged under the same conditions of 70°C for seven days. These results provide useful information about the positive effect of calcium-hydrolyzed nanoparticles on gold MTs and their conversion into sustainable building materials through alkali activation.

Of course, now we know that quantum mechanics has been a fundamental structure of our world since our universe came into being. However, it has been only a century since the experimental and theoretical discovery of quantum mechanics and its extensions into many implications and applications. In particular, there are implications across many disciplines that most likely will affect education, health, security, etc. Examples are given of the need for starting education as early as possible in schools, the use of nano-robots to deliver drugs targeted to specific molecular sites, to developing new cryptographic systems to safeguard our privacy.

The size of TiO2 (either nanometric or micrometric) can significantly affect both its photocatalytic and photoelectrochemical properties, thus altering the photooxidation of organic pollutants in air or water. The purpose of this work is to give an account of the photoelectrochemical and photocatalytic features of some nano- and micro-sized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulated electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals, or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the micro-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction.

Evaporation studies of water using classical molecular dynamics simulations are largely limited due to its high computational expense. We aim at addressing the computational issues by developing a coarse grain model for evaporation of water on solid surfaces by combining four water molecules into a single bead. Most commonly used mono atomic pair potentials like Lennard Jones, Morse, Mie and three body potential like Stillinger-Weber are optimized using a combination of Genetic algorithm and Nelder-Mead algorithm. Among them, Stillinger-Weber based model shows excellent agreement of density and Enthalpy of vaporization with experimental results for a wide range of temperatures. Further, the new water model is used to simulate contact angle of water and thin film evaporation from surfaces with different wettabilities.

Amorphous ferrite-type rare-earth (RE) substituted garnets and garnet-oxide nanocomposite layers are prepared on clear glass substrates by using RF magnetron sputter-deposition process. By using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method, the spectral dispersion function of optical constants and the layer thicknesses are derived accurately from the transmission spectra of the as-deposited samples. The effects of excess metal-oxides added to the base material systems during the co-deposition process are found to affect the refractive index and the optical absorption coefficients of garnet-oxide composites. A number of optical constant datasets are presented, enabling the experimentalists to design nanophotonic or integrated-optics devices employing these functional materials.

Aiming at the damage detection and continuous monitoring of high efficiency composite structure, the method of carbon nano sensor embeded in the 3-D braided composite material specimen was put forward and the method of damage location for 3-D braided composite material was described. In this paper, the mechanical and electrical characteristics of carbon nano-fiber were analyzed. Considering the massive data of the health monitoring of composite processing, to ensure that the system has good real-time performance, quaternary matrix Singular Value Decomposition algorithm is proposed to simplify data and improve the efficiency of the algorithm. The existence of injury is determined and the damage location is calculated by comparing with key features of healthy specimen. Experimental results prove the method is feasible and effective.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

Non-toroidal shape primary pass through protection current transformers (CTs) are used to measure high currents. Their design provides them with a big airgap that allow passing several cables per phase though them, which is the main advantage versus toroidal types, as the number of CTs required to measure the whole phase current is drastically reduced. The cables pass through the transformer window can be in several positions. As the isolines of the magnetic field generated by the primary currents are centered in the cables, if these cables are not centered in the transformer window, the magnetic field will be non-uniform along the transformer core. Consequently, local saturations can appear if the cables are not properly disposed causing the malfunction of the CT. In this paper, the performance of a non-toroidal shape protection CT is studied. The research is focused on the cable position influence in possible partial saturations of the CT when it is operating near to its accuracy limit. Depending on the cable position, the ratio of the primary and secondary currents can depart from assigned ratio. The validation of this phenomenon has been carried out via Finite Element Analysis (FEA) showing that partial transformer core saturations appears in areas of the magnetic core close to the cable. Applying FEA, also the admissible accuracy region for cable positioning inside the CT is delimited. Finally, the simulation results are ratified with experimental tests performed in non-toroidal protection CTs varying the primary cables’ positions, which are subjected to currents up to 5 kA, achieving satisfactory results. From this analysis, installation recommendations are given.

Phenotyping is the task of measuring plant attributes for analyzing the current state of the plant. In agriculture, phenotyping can be used to make decisions concerning the management of crops, such as the watering policy, or whether to spray for a certain pest. Currently, large scale phenotyping in fields is typically done using manual labor, which is a costly, low throughput process. Researchers often advocate the use of automated systems for phenotyping, relying on the use of sensors for making measurements. The recent rise of low cost, yet reasonably accurate, RGB-D sensors has opened the way for using these sensors in field phenotyping applications. In this paper, we investigate the applicability of 4 different RGB-D sensors for this task. We conduct an outdoor experiment, measuring plant attribute in various distances and light conditions. Our results show that modern RGB-D sensors, in particular, the Intel D435 sensor, provides a viable tool for close range phenotyping tasks in fields.

Loop-Mediated Isothermal Amplification (LAMP) is a widely used technique for nucleic acid amplification due to its high specificity, sensitivity, and rapid results. Advances in microfluidic lab-on-chip (LOC) technology have enabled the integration of LAMP into miniaturized devices, known as μ-LAMP, which require precise thermal control for optimal DNA amplification. This paper introduces a novel thermal bed design using PCB copper traces and FR−4 dielectric materials, providing a reliable, modular, and repairable heating platform. We present the design, fabrication, and control mechanisms of the thermal bed, demonstrating its ability to maintain accurate temperatures essential for μ-LAMP applications. The thermal bed’s performance is validated through finite element method (FEM) simulations, confirming its effectiveness in diverse applications such as disease diagnostics, biological safety, and forensic analysis.

Artificial Intelligence (AI) and Machine Learning (ML) are rapidly advancing. These technologies have significantly impacted the consumer goods market, including the smart footwear industry. AI and ML are extensively utilized in the design and production of smart and agile footwear. There are various methods for manufacturing smart footwear, which can be categorized based on their applications. These include medical and healthcare smart footwear, assistive footwear for individuals with impairments, footwear designed for navigation in unfamiliar areas, foot-wear for studying foot movements and gait analysis, safety footwear, anti-skid footwear, foot-wear for the elderly, army shoes, and energy-harvesting footwear, among others. These smart shoes enable real-time patient monitoring and provide appropriate suggestions for their care. Additionally, smart footwear can be classified based on the tools and techniques used in their production, as well as the sensors and Internet of Things (IoT) devices integrated into them. This paper reviews the various tools and techniques used in the creation of smart footwear for dif-ferent applications.

Sleep is a crucial aspect of geriatric assessment for hospitalized older adults, and implementing AI-driven technology for sleep monitoring can significantly enhance the rehabilitation process. Sleepsense, an AI-driven sleep-tracking device, provides real-time data and insights, enabling healthcare professionals to tailor interventions and improve sleep quality. This study explores the perspectives of an interdisciplinary hospital team on implementing Sleepsense in geriatric hospital care. Using the Interpretive Descriptive approach, we conducted focus groups with physicians, nurses, care aides, and an activity worker. The Consolidated Framework for Implementation Research (CFIR) informed our thematic analysis to identify barriers and facilitators to implementation. Among 27 healthcare staff, predominantly female (88.89%) and Asian (74.1%) and mostly aged 30-50 years, themes emerged that Sleepsense is perceived as a timesaving and data-driven tool that enhances patient monitoring and assessment. However, barriers such as resistance to change and concerns about trusting the device for patient comfort and safety were noted, while facilitators included training and staff engagement. The CFIR framework proved useful for analyzing implementation barriers and facilitators, suggesting future research should prioritize effective strategies for interdisciplinary team support to enhance innovation adoption and patient outcomes in rehabilitation settings.

The proliferation of wearable technology enables the generation of vast amounts of sensor data, offering significant opportunities for advancements in health monitoring, activity recognition, and personalized medicine. However, the complexity and volume of this data present substantial challenges in data modeling and analysis, which have been tamed with approaches spanning time series modeling to deep learning techniques. The latest frontier in this domain is the adoption of Large Language Models (LLMs), such as GPT-4 and Llama, for data analysis, modeling, understanding, and generation of human behavior through the lens of wearable sensor data. This survey explores current trends and challenges in applying LLMs for sensor-based human activity recognition and behavior modeling. We discuss the nature of wearable sensors data, the capabilities and limitations of LLMs to model them and their integration with traditional machine learning techniques. We also identify key challenges, including data quality, computational requirements, interpretability, and privacy concerns. By examining case studies and successful applications, we highlight the potential of LLMs in enhancing the analysis and interpretation of wearable sensors data. Finally, we propose future directions for research, emphasizing the need for improved preprocessing techniques, more efficient and scalable models, and interdisciplinary collaboration. This survey aims to provide a comprehensive overview of the intersection between wearable sensors data and LLMs, offering insights into the current state and future prospects of this emerging field.

This study presents a fit-for-purpose evaluation of commercially available portable sensor systems, measuring PM, NO2 and/or BC, through extensive lab- and field benchmarking. The main aim of the study is to identify sensor systems that can be used for mobile monitoring by citizens to assess dynamic exposure in ambient air. After an initial literature study and market search resulting in 39 sensor systems, 10 sensor systems were ultimately purchased and benchmarked in laboratory and real-word conditions. We evaluated comparability to reference analyzers, sensor precision and sensitivity to temperature, humidity and O3. Moreover, we evaluated if accuracy can be improved by the lab and field calibration. Because the targeted application of the sensor systems under evaluation is mobile monitoring, we conducted a mobile field test in an urban environment to evaluate the GPS accuracy and potential impacts from vibrations on the resulting sensor signals. Results of the considered sensor systems indicate that out-of-the-box performance is relatively good for PM and BC, but maturity of the tested NO2 sensors is still low and additional efforts are needed in terms of signal noise and calibration. The horizontal accuracy of the build-in GPS was generally good achieving a &lt;10m horizontal accuracy for all sensor systems. More accurate and dynamic exposure assessments in contemporary urban environments are crucial to study real-world exposure of individuals and exposome impacts on potential health endpoints. A greater availability of mobile monitoring systems capable of quantifying urban pollutant gradients will further boost this line of research.

This study was carried out with a low-cost electronic nose prototype based on eight metal oxide sensors (MQ) in order to characterize samples of lemons treated with 0.5% and 0.1% of sodium benzoate. The MQ sensors designed are sensitive to one or more chemicals to detect the presence of a variety of chemicals in the air. The sensor MQ135 detects ammonia, hydrogen sulphide and benzene. Signal data were studied to obtain a pattern recognition of rotten in lemon fruits. Network analysis was used to obtain a calibration of measures among the stage of lemons. In this article, an electronic nose prototype based on 8 MQ metal oxide sensors has been used in order to analyze and characterize different lemon varieties to which different chemical treatments have been applied in pre-harvest. PCA-based data analyzes were used to observe clusters in the data. Through the combined use of the data obtained by the nose and these Sequential Neural Networks (SNNs) a classification tool for lemon varieties and applied treatments has been obtained. It is shown the ability of this device to be used as a reliable discrimination method, in addition to providing low cost and optimization of time and expert resources.

Three-dimensional flexible piezoresistive porous sensors have been used in health diagnosis and wearable devices. By utilizing 3D printed sacrificial mold casting with highly conductive polymer composites, porous sensors with high conductivity and complex structures were achieved. Traditional conductive polymer composites are usually heated using external heat sources, which are time and energy consuming. However, in this study, conductive porous sensors with triply periodic minimal surface (TPMS) structures were manufactured using self-resistance electric heating by utilizing the conductive nature of the polymers. The porous structures were designed based on Diamond (D), Gyroid (G), and I-WP (I) unit cells of the TPMS. The use of self-resistance electric heating has improved the compression performance and piezoresistive response of the structures. Among these structures, the D-based structure exhibited the maximum response strain (61 %), with a corresponding resistance response value of 0.97, which increased by 10.26 % compared to that of the structures heated by using the external heat sources. This study offers a new perspective on designing and optimizing porous materials with specific functionalities, particularly in the realm of flexible and portable piezoresistive sensors.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

Seafood, especially from the ocean, is now seen as a greener and more sustainable source of protein causing an increase in its demand. This has also led to people making choices towards seafood as a replacement of carbon intensive protein sources. As a result, the demand for seafood is growing, and the Aquaculture industry is required to increase their produce while keeping the produce safe and sustainable. There are many challenges faced by the aquaculture industry in meeting these increased demands. One such challenge is the presence of harmful algal blooms (HAB) in the ocean which can have a major impact on aquatic life. In this paper we look at the impact of this challenge on aquaculture and the mitigating strategies. We will focus on Abagold Limited, a land-based marine aquaculture business that specializes in large scale production of abalone (Haliotis midae) based in Hermanus, South Africa. HABs are considered a threat to commercial scale abalone farming along the South-African coastline and requires continuous monitoring. The most recent HAB was in February-April 2019, the area experienced a severe red-tide event with blooms of predominantly Lingulodinium polyedrum. We present some of the mitigation strategies employing digital technologies for future proofing the industry.

Electrochemical sensors have been used for many decades. Yet, modeling of such sensors used in electrolysis mode is poorly documented, especially in the case parallel action of multiple gases. Those ones are of great interest since they constitute the first brick to bring information on natures and concentrations of a gaseous mixture composition thanks to grey box modeling of sensors array for example. Based on Butler Volmer’s equations, a model assuming parallel reactions at gold cathode has been introduced in this article and confronted to experimental results. Establishment of the model is based on the extraction of 3 variables: the charge transfer coefficient “α”, the reaction order γ, and the reaction constant rate k0. Tests performed without pollutants and with different concentrations of oxygen could be nicely fitted by the model. Then, the influence of polarization current on the 3 variables of the model has been evaluated showing a clear influence on the constant rate and the reaction order. Also, increasing the polarization current enabled us to get selectivity to oxidant gases. Similarly, the effect of the oxygen concentration was evaluated. Results showed that, in this case, the charge transfer coefficients “α” obtained for oxidant gases is quite different that the ones obtained in the polarization current varying conditions. Therefore, the model will be interesting in situations where polarization current and oxygen content are not varied together. Variation of polarization current can be quite interesting to get increased information for multivariate analysis purpose in constant oxygen content situations. Besides, other parameters have are required for applications in which the oxygen content is bound to change like exhaust gases or combustion.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

Accurate and reliable measurement of real-world walking activity is clinically relevant, particularly for people with mobility difficulties. Insights on walking can help understand mobility function, disease progression, and fall risks. People living in long-term residential care environments have heterogeneous and often pathological walking patterns, making it difficult for conventional algorithms paired with wearable sensors to detect their walking activity. We designed two walking bout detection algorithms for people living in long-term residential care. Both algorithms used thresholds on the magnitude of acceleration from a 3-axis accelerometer on the lower back to classify data as “walking” or “non-walking”. One algorithm had generic thresholds, while the other used personalized thresholds. To validate and evaluate the algorithms, we compared the classifications of walking/non-walking from our algorithms to the real-time research assistant annotated labels and the classification from an algorithm validated on a healthy population. Both the generic and personalized algorithms had acceptable accuracy (0.83 and 0.82 respectively). The personalized algorithm showed the highest specificity (0.84) of all tested algorithms, meaning it was the best suited to determine input data for gait characteristic extraction. The developed algorithms were almost 60% quicker than the previously developed algorithms, suggesting they are adaptable for real-time processing.

Infrared sensors incorporating suspended zinc oxide (ZnO) pyroelectric films and thermally-insulated silicon substrates are fabricated using conventional MEMS-based thin-film deposition, photolithography, and etching techniques. The responsivity of the pyroelectric film is improved through annealing at 500℃ for 4 h. The voltage response of the fabricated sensors is evaluated experimentally for a substrate thickness of 1 µm over a sensing range of 30 cm. The results show that the voltage signal varies as an inverse exponential function of the distance. A positioning system based on three infrared sensors is implemented in LabVIEW. It is shown that the position estimates obtained using the proposed system are in excellent agreement with the actual locations. In general, the results presented in this study provide a useful source of reference for the further development of MEMS-based pyroelectric infrared sensors.

At present, aeroponic control is mainly regulated according to the environmental factors of aeroponics, such as the temperature, humidity, light intensity, carbon dioxide concentration, pH, and electrical conductivity (EC) of the nutrient solution. There is a lack of knowledge available in the literature for an aeroponic control system for plant growth information as the primary feedback signal. Therefore, a fuzzy logic-controlled aeroponics system was developed for the growth of lettuce as a feedback signal. After designing, the effectiveness test of system was performed with experiment having three treatments T1 (180C), T2 (220C) and without control (CK). The results show an increasing trend in shoot length, root length, and shoot area over time in all treatments. In terms of shoot area, the maximum of 345 cm² was observed in the T1 treatment, while the CK treatment had a minimum of 241.8 cm². Statistical analysis indicated that the T1 and T2 treatments were not significantly different, but both were significantly different from the CK treatment. The study demonstrates the effectiveness of the fuzzy logic control system and an 18°C nutrient solution temperature, resulting in improved lettuce growth and reduced root-to-shoot ratio. The findings suggest the potential of using fuzzy logic control in aeroponics for optimized cultivation outcomes.

The condition of surface transportation infrastructure directly affects the economic health of a nation. However, it is difficult to justify the large sums of money needed to extend current methods to monitor all the multimodal infrastructure. The convergence of connected vehicle and cloud computing technologies presents an opportunity to automate the collection of ride quality and imagery data to continuously assess the condition of all roadways and railways. This paper presents several perspectives to help policy and standardization initiatives promote adoption.

Rapid growth of IoT applications and their interference in our daily lives led to many different IoT devices which generates enormous data. The IoT devices’ resources are very limited, so storing and processing IoT data in the devices is very inefficient. Several resources of cloud-computing are efficiently used to handle some IoT resources issues. While using resources in the cloud centers cause some other issues, like latency in the IoT applications, which are time-critical. Thus, the technology of edge cloud has evolved recently. This technology permits storage and data processing at the network edge. This paper studies edge computing in-depth for timeless sensitive devices in IoT. In-depth, cutting-edge IoT computing systems (ECAs-IoT) are evaluated and characterized in this paper according to numerous criteria, such as information placement, improvisation facilities, reliability, and data visualization. Moreover, according to distinctive properties, the paper aims at comparing each structure in detail. The paper also highlights the significant limitations of the new ECAs-IoT and recommends solutions to them. The studies also introduce and propose solutions to some of the most important restrictions of the current ECAs-IoT. Consequently, in the edge computing domain, this survey outlines the IoT implementations. Lastly, with the use of IoT implementations for ECAs-IoT, the paper suggests four distinct scenarios.

This mini-review critically summarizes the knowledge of imprinted polymer-based electrochemical sensors, for the detection of pesticides, metal ions and waterborne pathogenic bacteria, focusing on the period the last 5 years (citation of 78 papers published in 2017-2021, ie 63% of total citations). MIP-based electrochemical sensors exhibit low limit of detection, high selectivity, high sensitivity and low cost. Herein, we focused on the timely topics of water pollution by organics, inorganics and micro-organisms represented by pesticides, metal ions and bacteria, respectively. We put the emphasis on the design of imprinted polymers and their composites and coatings by radical polymerization, oxidative polymerization of conjugated monomers or sol-gel chemistry. Whilst most imprinted polymers are used in conjunction with differential pulse or square wave voltammetry for sensing organics and metal ions, electrochemical impedance spectroscopy (EIS) appears as the chief technique for detecting bacteria. This successful combination of EIS and imprinting technology should be harnessed in the coming years in the case of bacteria. Interestingly, bacteria are not always probed by bacteria-imprinted polymers; we report here their detection by monitoring specific (macro)molecules that reflect bacterial activity, for example quorum sensing signaling molecules or flagella proteins. If much has been developed in the past decade with glassy carbon or gold electrodes, it is clear that carbon paste electrodes of imprinted polymers are more and more investigated due to their versatility. Shortlisted case studies were critically reviewed and discussed; clearly a plethora of tricky strategies of designing selective electrochemical sensors are offered to “Imprinters”. We anticipate this review will be of interest to experts and new comers in the field who are paying time and effort combining electrochemical sensors with MIP technology.

In personalized healthcare, an ecosystem for the manipulation of reliable and safe private data should be orchestrated. This paper describes a first approach for the generation of fake electrocardiograms (ECGs) based on Generative Adversarial Networks (GANs) with the objective of anonymizing users’ information for privacy issues. This is intended to create valuable data that can be used both, in educational and research areas, while avoiding the risk of a sensitive data leakage. As GANs are mainly exploited on images and video frames, we are proposing general raw data processing after transformation into an image, so it can be managed through a GAN, then decoded back to the original data domain. The feasibility of our transformation and processing hypothesis is primarily demonstrated. Next, from the proposed procedure, main drawbacks for each step in the procedure are addressed for the particular case of ECGs. Hence, a novel research pathway on health data anonymization using GANs is opened and further straightforward developments are expected.

Increased smart devices in various industries is creating numerous sensors in each of the equipment prompting the need for methods and models for sensor data. Current research proposes a systematic approach to analyze the data generated from sensors attached to industrial equipment. The methodology involves data cleaning, preprocessing, basics statistics, outlier, and anomaly detection. Present study presents the prediction of RUL by using various Machine Learning models like Regression, Polynomial Regression, Random Forest, Decision Tree, XG Boost. Hyper Parameter Optimization is performed to find the optimal parameters for each variable. In each of the model for RUL prediction RMSE, MAE are compared. Outcome of the RUL prediction should be useful for decision maker to drive the business decision; hence Binary classification is performed, and business case analysis is performed. Business case analysis includes the cost of maintenance and cost of non-maintaining a particular asset. Current research is aimed at integrating the machine intelligence and business intelligence so that the industrial operations optimized both in resource and profit.

We present an Arduino-based automatic robotic system which is used for cutting grass or lawns, mostly healthy grass which needs to cut neatly like in a public park or a private garden. The purpose of this proposed project is to design a programmable automatic pattern design grass cutting robot with solar power which no longer requires time-consuming manual grass-cutting, and that can be operated wirelessly using an Android Smartphone via Bluetooth from a safe distance which is capable of cutting the grass in indeed required shapes and patterns; the cutting blade can also be adjusted to maintain the different length of the grass. The main focus was to design a prototype that can work with a little or no Physical user interaction. The proposed work is accomplished by using an Arduino microcontroller, DC geared Motors, IR obstacle detection sensor, motor shield, relay module, DC battery, solar panel, and Bluetooth module. The grass-cutting robot system can be moved to the location in the lawn remotely where the user wants to cut the grass directly or in desired patterns. The user can press the desired pattern button from the mobile application, and the system will start cutting grass in the similar design such as a circle, spiral, rectangle, and continue pattern. Also, with the assistance of sensors positioned at the front of the vehicle, an automatic barrier detection system is introduced to enhance safety measurements to prevent any risks. IR obstacle detector sensors are used to detect obstacles, if any obstacle is found in front of the robot while traveling; it avoids the barrier by taking a right/right turn or stop automatically appropriately, thereby preventing the collision. Also, the main aim of this project is the formation of a grass cutter that relieves the user from mowing their own grasses and reduces environmental and noise pollution. The proposed system is designed as a lab-scale prototype to experimentally validate the efficiency, accuracy, and affordability of the systems. The experimental results prove that the proposed work has all in one capability (Simple and Pattern based grass cutting with mobile-application, obstacle detection), is very easy to use, and can be easily assembled in a simple hardware circuit. We note that the systems proposed can be implemented on a large scale under real conditions in the future, which will be useful in robotics applications and cutting grass in playing grounds such as cricket, football, and hockey, etc.

It is since long known, that SAW devices, resonators as well as delay lines, can be used as passive wireless sensors for physical quantities like temperature and pressure as well as gas sensors or ID-Tags. The sensors are robust, work passively without battery, can be applied at high temperatures and provide a high resolution. Nevertheless, if the devices should be readout wirelessly in an industrial environment, several constraints have to be taken into account, especially when more than one quantity or device needs to be measured at the same time. The paper addresses the challenges that have to be tackled when establishing multi-sensor-wireless-readout for industrial applications. Major issues here are the legal ISM-band regulations, as well as sampling time and costs, which impose severe restrictions to any system design. We describe several design approaches and their constraints. We have successfully designed sensors based on reflective delay lines that allow the parallel readout of four independent temperature sensors in the 2.45 GHz ISM-band. These devices have been fabricated, positively tested and demonstrate the applicability of SAW sensors for industrial applications.

In this work, a tailored extreme learning machine (ELM) algorithm to enhance the overall robustness of gas analyzer based on the tunable diode laser absorption spectroscopy (TDLAS) method is presented. The ELM model is tailored through activation function selection, input weight and bias searching, and cross validation method to address the analyzer robustness issues for industrial process analysis field application. The two particular issues are the inaccurate gas concentration measurement caused by the process gas background components variation, and the inaccurate spectra shift calculation caused by spectral interference. By using our algorithm, the concentration error is reduced by one order of magnitude over a much larger stream pressure and component range compared with that obtained by classical least square (CLS) fitting methods based on reference curves. Additionally, it is shown that with our algorithm, the wavelength shift accuracy is improved to less than 1 count over 1000 counts spectra length. In order to test the viability of our algorithm, a trace ethylene (C₂H₄) TDLAS analyzer with coexisting methane was implemented, and its experimental measurements support analyzing robustness enhancement effect.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

Interviews from strength and conditioning coaches across all levels of athletic competition identified their two biggest concerns with the current state of wearable technology: (a) the lack of solutions that accurately capture data "from the ground up" and (b) the lack of trust due to inconsistent measurements. The purpose of this research is to investigate the use of liquid metal sensors, specifically Liquid Wire sensors, as a potential solution for accurately capturing ankle complex movements such as plantar flexion, dorsiflexion, inversion, and eversion. Sensor stretch linearity was validated using a Micro-Ohm Meter and a Wheatstone bridge circuit. Sensors made from different substrates were also tested and discovered to be linear at multiple temperatures. An ankle complex model and computing unit for measuring resistance values were developed to determine sensor output based on simulated plantar flexion movement. The sensors were found to have a significant relationship between the positional change and the resistance values for plantar flexion movement. The results of the study ultimately confirm the researchers' hypothesis that liquid metal sensors, and Liquid Wire sensors specifically, can serve as a mitigating substitute for inertial measurement unit (IMU) based solutions that attempt to capture specific joint angles and movements.

The study of localized surface plasmons (LSPs) in nanoscale structures is an essential step towards identifying optimal plasmonic modes that can facilitate robust optomechanical coupling and deepen our understanding of light-matter interactions at the nanoscale. This paper investigates numerically, using the finite element method, LSPs modes in a design comprising two coupled nano-ridges deposited on a gold layer, with an interposing polymer spacer layer. Such a structure, usually referred to as particles-on-mirror, shows exquisite optical properties at the nanoscale. We first examine the LSPs modes of a single nano-ridge through the analysis of its scattering cross-section in the visible and infrared range. To enhance the plasmonic response, a thin polymer layer is placed at the middle of the ridge, which introduces additional LSPs modes confined within the former. Then, we extend the analysis to the dimer configuration, which exhibits more complex and enhanced plasmonic behavior compared to a single nano-ridge. In particular, the dimer configuration yields LSPs resonances with a quality factor enhancement of approximately threefold relative to single nano-ridge. Furthermore, the presence of the polymer layer within the ridges significantly improves plasmon field localization and quality factor. These findings underscore the potential of nano-ridge-based structures in advancing optomechanical coupling and plasmon-phonon interaction studies, offering valuable insights for the development of high-performance acousto-plasmonic devices. In particular, the proposed device could help significantly improve the design of nano-acousto-optic modulators operating in the visible or in the near infrared, that require enhanced light-photon coupling rate.

CO2 geological sequestration in coal seams can achieve the dual objectives of CO2 emission reduction and enhanced coalbed methane production, making it a highly promising carbon capture and storage technology. However, the injection of CO2 into coal reservoirs in the form of supercritical fluid (ScCO2) leads to complex physicochemical reactions with the coal seam, altering the properties of the coal reservoir and impacting the effectiveness of CO2 sequestration and methane production enhancement.In this paper, theoretical calculations based on ReaxFF-MD were conducted to study the interaction mechanism between ScCO2 and the macromolecular structure of both low-rank and high-rank coal, to address the limitations of experimental methods. The reaction of ScCO2 with low-rank coal and high-rank coal exhibits significant differences. At swelling stage, the low-rank coal experiences a decrease in aromatic structure and aliphatic structure, high-rank coal shows an increase in aromatic structure and a decrease in aliphatic structure, while swelling phenomenon is more pronounced in high-rank coal. At dissolution stage, low-rank coal is initially decomposed into two secondary molecular fragments, and then recombine to form new molecular structure, the aromatic structure increased and the aliphatic structure decreased. In contrast, high-rank coal occurs stretches-breakage-movement-reconnection, a reduction in aromatic structure and an increase in aliphatic structure.The primary reasons for these variations lie in distinct molecular structure compositions and the properties of ScCO2, leading to different reaction pathways of functional group and aromatic structure. The reaction pathways of functional groups and aromatic structures in coal can be summarized as follows: the breakage of the O-H bond in hydroxyl groups, the breakage of the C-OH bond in carboxyl groups, transformation of aliphatic structures into smaller hydrocarbon compounds or formation of long-chain alkenes, and various pathways involving broken, rearrangement, recombination of aromatic structures. In low-rank coal, there is a higher abundance of oxygen-containing functional groups and aliphatic structures. The breakage of O-H and C-OH chemical bonds results in the formation of free radical ions, while some aliphatic structures detach to produce hydrocarbons. Additionally, some of these aliphatic structures combine with carbonyl groups and free radical ions to generate new aromatic structures. Conversely, in high-rank coal, the lower content of oxygen-containing functional groups and aliphatic structures, along with stronger intramolecular forces, results in fewer chemical bond breakages and makes it less conducive to the formation of new aromatic structures.These results elucidate the specific deformations of different chemical groups, offering a molecular-level understanding of the interaction between CO2 and coal.

Micro nano bubbles (MNBs) can generate ·OH in situ, which provides a new idea for the safe and efficient removal of pollutants in water supply systems. However, the difficulty in obtaining stable MNBs causes the low efficiency of ·OH generation, which makes the inability to guarantee the removal efficiency of pollutants. This paper reviews the application research of MNBs technology in water security from three aspects: the generation process of MNBs in water, the generation rule of ·OH during MNBs collapse, and the control mechanism of MNBs on pollutants and biofilms. We found that MNBs generation methods are divided into chemical and mechanical (about 10 kinds) categories, and the instability of bubble size restricts the application of MNBs technology. The generation of ·OH by MNBs is affected by pH, gas source, bubble size, temperature, external stimulation. And pH and external stimulus have more influence on ·OH generation in situ than other factors. Adjusting pH to alkaline or acidic conditions and selecting ozone or oxygen as the gas source can promote the ·OH generation. MNBs’ collapse also releases a large amount of energy, which the temperature and pressure can reach 3000K and 5Gpa respectively, making it efficient to remove ≈90 % of pollutants (i.e., trichloroethylene, benzene, and chlorobenzene). The biofilm can also be removed by physical, chemical, and thermal effect. MNBs technology also has great application potential in drinking water, which can be applied to improve water quality, optimize household water purifiers, and enhance the taste of bottled water. Under the premise of safety, let people of different ages taste, finding that compared with ordinary drinking water, 85.7 % of people think MNBs water is softer, 73.3 % of people think MNBs water is sweeter. This further proves that MNBs water has a great prospect in the drinking water application. This review provides innovative theoretical support for solving the problem of drinking water safety.

Protein–nanoparticle hybridization can ideally lead to novel biological entities characterized by emerging properties, which can sensibly differ from those of the parent components. Herein, the effect of ionic strength on the biological functions of recombinant, His-tagged spermine oxidase (i.e., SMOX) was studied for the first time. Moreover, SMOX was integrated to colloidal surface active maghemite nanoparticles (SAMNs) by direct self-assembly, leading to a biologically active nano-enzyme (i.e., SAMN@SMOX). The hybrid was subjected to an in-depth chemical-physical characterization highlighting that protein structure was perfectly preserved. The catalytic activity of the nanostructured hybrid (SAMN@SMOX) was assessed by extracting kinetics parameters using spermine as substrate and compared to the soluble enzyme as a function of ionic strength. Results revealed that the catalytic function was dominated by electrostatic interactions and that they were drastically modified upon hybridization with colloidal ɣ-Fe2O3. Noteworthy, the affinity of SMOX toward spermine was significantly higher for the nanohybrid at low salinity. The present study supports the vision of using protein–nanoparticle conjugation as a mean for modulating biological functions.

Significant amount of oil remains in the reservoir after primary and secondary operations and to recover the remaining oil, enhanced oil recovery (EOR) can be applied as one of the feasible options remaining nowadays. In this study new nano polymeric materials have been prepared from purple yam and cassava starches. The yield of purple yam nanoparticles (PYNPs) was 85% and that of cassava nanoparticles (CSNPs) is 90.53%. Synthesized materials were characterized through particle size distribution (PSA), zeta potential distribution, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The performance of PYNPs in recovering oil was better than CSNPs as found from recovery experiments. Zeta potential distribution results confirmed the stability of PYNPs over CSNPs (-36.3 mV for PYNPs and -10.7 mV for CSNPs). The optimum concentration for these nanoparticles has been found from interfacial tension measurements and rheological properties and it was 0.60 wt.% for PYNPs and 0.80 wt.% for CSNPs. More incremental recovery (33.46%) has achieved for the polymer that contained PYNPs in comparison to the other nano-polymer (31.3%). This opens the inception for a new technology for polymer flooding that may replace the conventional method that depends on partially hydrolyzed polyacrylamide (HPAM).

We synthesized iron(II)-triazole spin crossover compounds of the type [Fe(atrz)3]X2 and incorporated and deposited them on electrospun polymer nanofibers. In view of possible applications, we chose iron(II)-triazole-complexes that are known to exhibit spin crossover close to ambient temperature. Therefore we used the complexes [Fe(atrz)3]Cl2 and [Fe(atrz)3](2ns)2 (2ns = 2Naphthalenesulfonate) and analyzed them with IR-, UV/Vis and Mossbauer spectroscopy and with a SQUID magnetometer. The synthesized complexes were then in one attempt deposited on fibers of polymethylmethacrylate (PMMA) and in another attempt incorporated into core-shell like PMMA fiber structures. This was done via two different electrospinning methods. Deposition was performed by uniaxial electrospinning and incorporation was performed by coaxial electrospinning. The obtained polymer-complex-composites were then further investitgated by the same methods as the pure complexes as well as by SEM pictures and EDX measurements. The analysis by UV/Vis spectroscopy, Mössbauer spectroscopy and temperature-depended magnetic measurements with the SQUID magnetometer showed that the spin crossover properties were maintained and were not changed after the electrospinning processes and that the complexes were not harmed during the procedure.

The physicalchemistry properties and crystal structure of were nano-ZrO₂+3mol.%Y₂O₃ determined. The kinetics of the formation of H₂ as a result of the decomposition of H₂O on the surface of nano-ZrO₂+3mol.%Y₂O₃ was studied. Effects of adsorption and desorption process on ZrO₂+3 mol.%Y₂O₃ nanoparticles were studied at different (T=400÷1000⁰C) temperature. The study of H₂ in thermal processes at nano-ZrO₂+3 mol.%Y₂O₃ system increased. Such an increase in H₂ generation in comparison with a pure H₂O as thermal processes had formedactive centers for H₂O decomposition on the surface of the catalyst at the expense of δ-electrons emitted on the surface of nano-ZrO₂+3 mol.%Y₂O₃. This showed that the dimensions of the studied nanoscale particles systems are comparable to the free running distance of energy carriers generated by of nano-ZrO₂+3 mol.%Y₂O₃ as a result of thermal processes. These results are promising for hydrogen generation by waer spliting in near future.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

We fabricated the nano-aperture plasmonic platforms for single molecule detection and other various applications such as infrared thermal emission device. The nano-apertures including the nanopores on the pyramid, and the nano-slits on the Au flat membrane were fabricated using a Ga ion focused ion beam drilling technique, followed by high energy electron beam irradiations dependent upon the electron beam current density. The nanopores with a few nanometer size and the nanoslit array with order of ~ 100 nm width were fabricated. Optical characteristics for the various nanoslits were examined dependent upon the slit opening width and sample thickness. The broad emission spectra from the (7x 7) slit array are obtained from spp-mediated emission in the visible and infrared region. A sharp strong infrared emission peak is also obtained due to Au nanoparticle. The fabricated Au platform can be utilized as single molecule sensor and infrared thermal emission device.

The fundamental question in the field of sensor research is new directions of scientific fields, which play a vital role in the progress of science and technology. This study confronts this question here by developing a bibliometric analysis, which endeavors to explain the evolution of sensor research and new technologies that are critical to science and society. The database of Scopus concerning scientific documents and patents is used for statistical and computational analyses in these topics. Results suggest that emerging technological trajectories in sensors are wireless sensor networks, wearable sensors and biosensors. Main characteristics of these growing research fields and technologies in sensors are described for fruitful implications of research and innovation policy directed to science advances and technological change in society.

The awareness of the existence in plants of bioactive compounds namely phytochemicals (PHYs), having health properties is progressively expanding. Therefore, their massive introduction in the normal diet, in food supplements, and their use as natural therapeutics to treat several diseases are increasingly emphasized by several sectors. Particularly, most PHYs possessing antifungal, antiviral, anti-inflammatory, antibacterial, antiulcer, anti-cholesterol, hypoglycemic, immunomodulatory, and antioxidant properties have been isolated from plants. Additionally, their secondary modification with new functionalities, to further improve their intrinsic beneficial effects, is extensively investigated. Unfortunately, although the idea of exploiting PHYs as therapeutics is amazing, its realization is far from simple, and the possibility of exploiting them as effective orally administrable drugs is almost utopic. Most PHYs are insoluble in water and, when introduced orally, they scarcely reach the site of action in therapeutic concentrations. Degradation by enzymatic and microbial digestion, occurring in the mouth, stomach, and intestine, as well as fast metabolism and rapid excretion via the kidney, biliary, or lung, strongly limit their in vivo activity. To overcome these drawbacks, several nanotechnological approaches have been used and many PHYs-loaded delivery systems with dimensions of nanometers have been developed. This paper, also by reporting various recent case studies, reviews the foremost nano-suspension and nano-emulsion-based techniques developed for formulating the most relevant PHYs in more bioavailable nanoparticles (NPs), suitable or promising for clinical application. Also, the acute and chronic toxic effects due to the exposure to NPs reported so far, the possible nanotoxicity which could derive by their massive employment, as well as the ongoing actions to improve the knowledge in the field were discussed. The state of the art concerning the actual clinical application of both PHYs and the nanotechnologically engineered PHYs was also reviewed.

Sinkhole formation caused by leaking pipes in karst soluble rocks is a significant concern, leading to infrastructure damage and safety risks. In this paper, an experiment was conducted to investigate sinkhole formation in dense sand induced by a leaking pipe. Fibre Bragg gratings (FBGs) sensors were used to record the strain. A balloon was gradually deflated within a bed of wet silica sand to create an underground cavity. Eighteen FBG sensors, with a wavelength range between 1550 nm and 1560 nm, were embedded horizontally and vertically in the physical model at different levels to monitor deformation at various locations. A leaking pipe was installed to induce the collapse of the formed arch above the cavity. The strain measurements suggest four phases in the sinkhole formation process: (1) cavity formation, (2) progressive weathering and erosion, (3) catastrophic collapse, and (4) subsequent equilibrium conditions. The results showed differences in strain signatures and distributions between horizontal and vertical measurements. During the critical phase of sinkhole collapse, horizontal measurements primarily showed tension, while vertical measurements indicated compression. This investigation demonstrates the effectiveness of FBGs as advanced monitoring tools for sinkhole precursor identification. The study also suggests using FBGs in geotechnical monitoring applications to improve understanding and mitigation of sinkholes and related geohazards.

Background: Gait analysis systems offer invaluable insights for rehabilitation, yet their expense limits clinician access. We developed GAITWell®, a low-cost modular system for capturing spatiotemporal gait variables, and evaluated its measurement properties. Methods: The GAITWell® uses discreet binary sensors on interconnected boards to collect gait data, which is then analyzed using the DBSCAN algorithm on the Cartesian points from sensor outputs. Reliability was assessed using ICC2,1, standard error of the mean (SEM) and Bland-Altman plots. Validity was determined by comparing GAITWell® with the Qualisys Pro-Reflex system. Results: Participated 38 healthy adults, with an average age of 33.2 years (SD 13.0). Correlations between GAITWell® and the Qualisys system ranged from moderate to very high for most gait variables, with the exception of stride length, which demonstrated a low but significant correlation (r = .360, p &lt; .05). The ICC2,1 indicated moderate to good agreement for most gait variables. Stance and double support times, cadence, and base of support exhibited poor reliability, characterized by larger SEM and limits of agreement. Conclusions: Our findings indicate that the GAITWell® system is a promising tool for gait analysis. Future research will enhance sensor accuracy and refine algorithms to improve reliability.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

In this study on volume determination in waste sorting facilities, we evaluate the effectiveness of ultrasonic sensors and address waste-material-specific challenges. Although ultrasonic sensors offer a cost-effective automation solution, their accuracy is affected by irregular waste shapes, varied compositions, and environmental factors. Notable inconsistencies in volume measurements between storage bunkers and conveyor belts underscore the need for a comprehensive approach to standardize bale production. With prediction reliability being constrained by limited data sets, undocumented modifications to machine-settings and sensor failures, this task renders a challenging application area for Machine Learning. We explore related research and present dataset analyses from three distinct waste sorting facilities in Europe, addressing issues as sensor usability, data quality and material specifics. Our analysis suggests promising strategies and future directions for enhancing waste volume measurement accuracy, ultimately aiming to advance sustainable waste management.