The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

The high demand for lithium (Li) relates to clean renewable storage devices and the advent of electric vehicles (EVs). The extraction of Li ions from aqueous media calls for efficient adsorbent materials with various characteristics, such as good adsorption capacity, good selectivity, easy isolation of the Li-loaded adsorbent, and good recovery of the adsorbed Li ions. The widespread use of metal-based adsorbent materials for Li ions extraction relates to various factors: (i) the ease of preparation via inexpensive and facile templation techniques, (ii) excellent selectivity for Li ions in a matrix, (iii) high recovery of the adsorbed ions, and (iv) good cycling performance of the adsorbents. However, the use of nano-sized metal-based LISs is limited due to challenges associated with isolating the loaded adsorbent material from the aqueous media. Adsorbent granulation process employing various binding agents (e.g., biopolymers, synthetic polymers, and inorganic materials) affords functional particles with modified morphological and surface properties that support easy isolation from the aqueous phase upon adsorption of Li ions. Biomaterials (e.g., chitosan, cellulose, alginate, and agar) are of particular interest because their structural diversity renders them amenable to coordination interactions with metal-based LISs to form 3D microcapsules. The current review highlights recent progress in the use of biopolymer binding agents for the granulation of metal-based LISs, along with various crosslinking strategies employed to improve the mechanical stability of the granules. The study reviews the effects of granulation and crosslinking on adsorption capacity, selectivity, isolation, recovery, cycling performance and the stability of the LISs. Adsorbent granulation using biopolymer binders has been reported to modify the uptake properties of the bio-adsorbent materials to varying degrees, in accordance with the surface and textural properties of the binding agent. The review further highlights the importance of granulation and crosslinking for improving the extraction process of Li ions from aqueous media. This review contributes to manifold areas related to industrial application of LISs, as follows: 1) to highlight recent progress in the granulation and crosslinking of metal-based adsorbents for Li ions recovery, 2) to highlight the advantages, challenges, and knowledge gaps of using biopolymer-based binders for granulation of LISs, and finally, 3) to catalyze further research interest into the use of biopolymer binders and various crosslinking strategies to engineer functional adsorbent materials for application in Li extraction industry. Properly engineered extractants for Li ions are expected to offer various cost benefits in terms of capital expenditure, percent Li recovery, and reduced environmental footprint.

In this study, various diamine monomers were used to synthesize aramid polymer films via a low-temperature solution condensation reaction with diacid chloride. For diamines with relatively high basicity, the reaction system became opaque because amine salt formation inhibited polymer synthesis. Meanwhile, low-basicity diamines with strong electron-withdrawing groups, such as CF3 and sulfone, were smoothly polymerized without amine salt formation to provide highly viscous solutions. The acid byproduct HCl generated during polymerization was removed by adding propylene oxide to the reaction vessel and converting the acid into highly volatile inert substances. The resulting solutions were used as varnishes without any additional purification, and polymer films with an excellent appearance were easily obtained through a conventional casting and convection drying process. The films neither tore nor broke when pulled or bent by hand; furthermore, even when heated up to 400°C, they did not decompose or melt. Moreover, polymers prepared from 2,2-bis (trifluoromethyl) benzidine (TFMB) and bis (4-aminophenyl) sulfone (pAPS) did not exhibit glass transition until decomposition. The prepared polymer films showed a high elastic modulus of more than 4.1 GPa and a high tensile strength of more than 52 MPa. In particular, TFMB-, pAPS-, and 2,2-bis (4-aminophenyl) hexafluoropropane-based polymer films were colorless and transparent, with very high light transmittances of 95%, 96%, and 91%, respectively, at 420 nm and low yellow indexes of 2.4, 1.9, and 4.3, respectively.

Self-compacting concrete (SCC) is a high-quality construction solution combining high fluidity, passing and filling ability with improved mechanical properties and durability. In the present study, the effect of incorporating alternative waste materials, such as two by-products of the ce-ment industry, namely cement kiln dust (CKD) and by-pass dust (BPD), into SCC as partial re-placement for traditional filler material was investigated. The produced compositions were compared with reference mixtures containing only marble powder (MP) as a filler. A series of tests including specific test methods for wet SCC, compressive, flexural and tensile splitting strength tests as well as drying shrinkage determination were conducted to evaluate the quality of the produced SCC in terms of fresh and hardened SCC properties. The use of alternative fine filler materials resulted in a high-performance sustainable SCC of low cement content. Specifi-cally, incorporating CKD into the SCC enhanced its rheological behavior and improved slightly its mechanical properties, while the use of BPD led to SCC mixtures of adequate rheological characteristics but with highly upgraded mechanical and physical properties

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

This study aims at the sustainable valorization of eggshells (ES) from different countries of origin in cement concrete as a cement replacement for Hong Kong. For this purpose, sixteen different eggs from different regions across the world were selected from the local market. Firstly, the extent of uniformity in the weight and mineral content of sampled eggshells were assessed by a specific gravity test and thermogravimetric analysis (TGA), respectively. It was found that specific gravity varies between 2.02 and 2.39, with an average value of 2.20 ± 0.01, whereas CaCO₃ varies between 94.65% and 97.23%, with an average value of 96.33%. These values were a bit lower than those of extra-pure limestone (LS) because of the organic part and the porous structure of eggshells. Secondly, three different eggshells were selected for cement replacement in cement concrete, both in the uncalcined and calcined states, based on having the highest, medium, and lowest CaCO₃ content, respectively. To get the calcined eggshells, the eggshells were calcined at 800^oC for three hours. It was found that the strength of eggshells varies with CaCO₃, but the variation was acceptable. The calcined eggshells showed comparatively more compressive strength and were close to the LS because of the free CaO and the absence of an organic part. In general, the variation in the basic properties of eggshells from different regions across the world is negligible and suitable to use as a cement replacement with acceptable variation in strength in Hong Kong.

According to the development needs of marine seismic station networking, it is necessary to develop a marine seismometer with a networking function to realize quasi-real-time and large-scale long-term observation of undersea seismic signals. This can lay a solid foundation for marine seismic research and research on earth tectonics, activities, and processes. Based on the advantages and disadvantages of the existing observation equipment, this study proposed to develop a new type of the Autonomous Glide Marine Seismometer(AGMS) that can be applied to the global sea area, focusing on the design and study of the main structure of the carrier of the AGMS. The ultimate strength of the ellipsoidal pressure-resistant spherical shell is investigated by using the finite element analysis method. A reasonable finite element analysis model is proposed through comparing the finite element parameter results with the theoretical formulas and relevant specifications. Finally, the design process and strength checking of the pressure-resistant shell of the AGMS are established. These relevant results can also provide a reference for the design of other deep-sea pressure-resistant chambers.

On the analyzed section of 2.4 km of the national road No. 50 of the Młodzieszyn bypass, it was carried out by a consortium of OAT and SAT companies in the period April-September 2019, under constant traffic in the field of repairing the concrete pavement by replacing slabs, levelling them and sealing expansion joints, roughening and roadside reinforcements.

This study investigates the influence of the porous structure, on the density and the mechanical behaviour of new foam concretes incorporating hemp shives. A total of eight batches of foam concretes were manufactured and tested, made with a protein-based foam agent, containing cement, ground granulated blast furnace slag and Metakaolin as binder and hemp shives as natural aggregate. The effect of several parameters is studied, elaboration method (direct and preformed), amount of pozzolanic additions (0% and 30%) and incorporation of hemp shives (5 and 15 vol%) on the resulting physical properties, microstructure, porous structure and mechanical behaviour of the concretes. Hemp shives incorporation results in increased concrete porosity and air bubble radius, decreased uniformity and mechanical strength, and lower cohesion with the cement matrix compared to standard concretes.

Water damage is one of the main causes of roads’ deterioration throughout their service life. This effect harms the adhesion and cohesion parameters of the asphalt mix, which leads to a decrease in the structural and functional characteristics of the road surface. This research focuses on studying the water susceptibility of hot mix asphalt mixtures using three different procedures: (1) UNE-EN 12697-12, (2) ASTM D4867, and (3) AASHTO T-283. The tests are carried out on reference mixtures and mixtures modified with polyethylene terephthalate (PET) particles as an additive. The results indicate that the incorporation of 6% PET allows the limits established by the UNE-EN 12697-12 standards to be exceeded, reaching 86% of the tensile strength ratio (TSR). However, for the ASTM D4867 and AASHTO T-283 standards, the results obtained concerning the water susceptibility of the bituminous mixtures were not as satisfactory because the established minimum limits were not reached (< 75%), which indicates that the procedure applied in a test can significantly modify the results of a later application.

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

Polymeric wet-strength agents are important additives used in the paper industry to improve the mechanical properties of paper products, especially when they come in contact with water. These agents play a crucial role in enhancing the durability, strength, and dimensional stability of paper products. The aim of this review is to provide an overview of the different types of wet-strength agents available and their mechanisms of action. We will also discuss the challenges associated with the use of wet-strength agents and the recent advances in the development of more sustainable and environmentally friendly agents. As the demand for more sustainable and durable paper products continues to grow, the use of wet strength agents is expected to increase in the coming years.

Self-healing ceramic composites are promising smart materials for high-temperature applications. To better understand their behaviors under service conditions, numerous studies have been performed both experimentally and numerically, and kinetics parameters such as activation energy and frequency factor are reported to be indispensable for investigating healing phenomena. Here, we propose a method for determining the kinetic parameters of self-healing ceramic composites based on the oxidation kinetics model of strength recovery. These parameters are determined by an optimization method using experimental strength recovery data under various healing temperatures and times and microstructural features on the fractured surfaces. Alumina and mullite matrix-based self-healing ceramic composites, such as Al2O3/SiC, Al2O3/TiC, Al2O3/Ti2AlC (MAX phase), and mullite/SiC, were selected as target materials. The theoretical strength recovery behaviors of the cracked specimens obtained from the determined kinetic parameters were compared with the experimental results. The determined parameters are within the previously reported range, and the predicted strength recovery behaviors are reasonably agreed with the experimental values. The proposed method can also be applied to other self-healing ceramics with matrices reinforced with different healing agents to evaluate oxidation rate, crack healing rate, and theoretical strength recovery behaviors for designing self-healing materials used in high temperature applications. Furthermore, the healing ability of composites can be fairly discussed regardless of the type of strength recovery test.

Indoor localization is an active area of research dominated by traditional machine-learning techniques. Deep learning-based systems have shown unprecedented improvements and have accomplished exceptional results over the past decade, especially the Transformer network within natural language processing (NLP) and computer vision domains. We propose the hyper-class Transformer (HyTra), an encoder-only Transformer with multiple classification heads (one per class) and learnable embeddings, to investigate the effectiveness of Transformer-based models for received signal strength (RSS) based WiFi fingerprinting. HyTra leverages learnable embeddings and the self-attention mechanism to determine the relative position of the wireless access points (WAPs) within the high-dimensional embedding space, improving the prediction of user location. From an NLP perspective, we consider a fixed order sequence of all observed WAPs as a sentence and the captured RSS value(s) for every given WAP at a given reference point from a given user as words. We test our proposed network on public and private datasets of different sizes, proving that the quality of the learned embeddings and overall accuracy improves with increments in samples.

The optimization of production of lignin-nanofiber-filled thermoplastic starch composite film for potential application in food packaging was carried using Response Surface Methodology (RSM), through the adoption of the Box-Wilson Central Composite Design (CCD) with 1 center point. The effects of filler loading on moisture absorption (MAB), tensile strength [TS], percent elongation [PE] and Young’s modulus [YM]) of the films were investigated in order to construct the desirability indices of the composite. The quality of the fitting model was expressed by the coefficient of determination, R2 and the adjusted R2. Results showed that the nanocomposite films were best fitted by a quadratic regression model with a high coefficient of determination (?2) value. The selected film has desirability of 76.80%, close to the objective function, and contained 4.81% lignin and 5.00% nanofibre. The MAB, TS, YM and PE of the selected film were 17.80 %, 21.51 MPa, 25.76 MPa and 48.81%, respectively. The addition of lignin and nanofiber to starch composite reduced the moisture absorption tendency but increased the mechanical properties of the films due to the good filler/matrix interfacial adhesion. Conclusively, results suggested that these films would be suitable for packaging application.

The aim of the study is to assess the loads that are transferred from the main rotor and the tail rotor to the helicopter fuselage. These loads change in the various phases of the transient flight as a result of the variable control of the maneuver and as a result of the variable flow around the blades. The knowledge of the loads allows for the proper selection of the level of excitations that should load the fuselage structure during fatigue and strength tests. The simulation model describing the helicopter flight is discussed. This model takes into account the motion of each blade relative to its hinges. Results are shown for two maneuvers - pullup/pushover and diving. The values of extreme loads transferred to the fuselage were obtained.

The brittle shear failure of reinforced concrete beams is complexed and unfavorable. For decades, research on the mechanical properties and durability of recycled coarse aggregate (RCA) to make recycled aggregate concrete (RAC) has been widely investigated. However, test results on the shear strength of reinforced recycled aggregate concrete beams are still limited and contradictory. This paper reports the shear strength of reinforced recycled aggregate concrete beams without stirrups. Eight RAC beams and two controlled beams with natural coarse aggregate (NCA) were tested under the four-point flexural test with the shear span-to-effective depth ratio (a/d) of 3.10. Parameters in this study were the replacement percentage of RCA (0%, 25%, 50%, 75%, and 100%) and longitudinal reinforcement ratio (w) of 1.16% and 1.80%. It was found that the normalized shear stresses of RAC beams with w = 1.80% at all levels of replacement percentage were quite similar to that of the NAC counterparts. Normalized shear stress of the beam with 100% RCA and w = 1.16% was lower than that of the NAC beam by 5%. Database of 128 RAC beams without shear reinforcement from literature was analyzed to evaluate the ability of the most recent ACI 318-19 shear provisions in shear strength prediction. A reduction factor of 0.75 is proposed to the current ACI code provision to account for the physical variations of RCA such as replacement percentage, RCA source and quality, density, amount of residual mortar, and physical irregularity.

The bending performance of a basalt-polypropylene fiber-reinforced concrete (HBPFRC) was characterized by testing 24 400×100×100 mm3 prismatic specimens in a four-point bending test JSCE-SF4 configuration. The type and content of both fibers was varied in order to guarantee different target levels of post-cracking flexural performance. The results evidenced that mono-micro basalt fiber reinforced concrete (BFRC) allows the increase of the flexural strength (pre-cracking stage), while macro polypropylene fiber reinforced concrete can effectively improve both bearing capacity and ductility of the composite for a wide crack width range. Compared with the plain concrete specimens, flexural toughness and equivalent flexural strength of macro polypropylene fiber-reinforced concrete (PPFRC) and the hybrid fiber-reinforced concrete (HFRC) increased by 3.7~7.1 times and 10%~42.5%, respectively. From both technical and economic points of view, the optimal mass ratio of basalt fiber to polypropylene fiber resulted to be 1:2, with a total content of 6 kg/m3. This HFRC is seen as a suitable material to be used in sewerage pipes where cracking control (crack formation and crack width control) is of paramount importance to guarantee the durability and functionality of the pipeline as well as the ductility of the system in case of local failures.

Several types of hematite nanoparticles (α-Fe2O3) have been investigated for their effects on the structure and properties of fly ash (FA) blended cement. All synthesized nanoparticles were found to be spherical shape, but of different particle sizes from 10 to 195 nm depending on the surfactant used in their preparation. The cement hydration with time showed 1.0% α-Fe2O3 nanoparticles was an effective accelerator for FA blended cement. Moreover, adding α-Fe2O3 nanoparticles in FA blended cement enhanced the compressive strength and workability of cement. Nanoparticle size and size distribution were important for optimal filling of various size of pores within the cement structure.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

Fiber-cement composites were prepared from cellulosic cotton residue (CCR) arise from sanding process (emerizing). The effect of different concentrations: 0.5% and 1%, and granulometry: thick (retained in a14 mesh sieve) and thin (retained in a 48 mesh sieve) of this residue were evaluated on tensile strength of cement slurries with seven (07) curing days. To characterize the CCR, TGA, FT-IR, SEM and XRD analysis were performed and the residue resistance in an alkaline environment was also evaluated. Splitting tensile strength test, known as Brazilian Test, was used to assess effects of the fibers on the mechanical behavior of cement matrix. Analyzing the results, the CCR proved to be resistant in an alkaline environment, meaning that it can withstand the alkaline environment of cement matrix. The results showed an improvement superior to 17% in tensile strength for 1% of CCR. Therefore, the CCR presents a great application potential in cement pastes used for oil well cementing that requires to increase its tensile strength, once a significant improvement was achieved with a low-residue employee.

This study aims to model grinding of a Polish slag and evaluate the particle size distributions of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e. temperature, curing and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin-Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multi fractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

It has been regarded that Vibrio cholerae O1 inhabit in environmental water. As many cholera patients emerge in Kolkata, it has been thought that V. cholerae O1 is easily detected in environmental water in Kolkata. However, the detection of V. cholerae O1 is rare, though other V. cholerae (NAG Vibrio) is constantly detected. To clear the reason for the difference of the detection rate of two Vibrios, we examined the viability of V. cholera O1 and NAG Vibrios in low ionic strength aquatic medium. We observed greater declining viability of V. cholerae O1 possessing cholera toxin gene (ctx) in low ionic strength solution, but the decline of NAG Vibrios non-possessing ctx is small. To evaluate the concerning of ctx in the viability, we examined the viabilities of V. cholerae O1which do not possess ctx and NAG Vibrios possessing ctx under the same condition. The result indicated that the existence of the ctx induces the decrease the viability of the host in low ionic strength solution. The decrease observed in this experiment might relate with the low detection of V. cholerae O1 possessing ctx in environmental water, though NAG Vibrio is constantly detected.

By using hydrogen quench continuous annealing technology, Stelco Inc. has developed a suite of Advanced High Strength Steel (AHSS) grades with tensile strength greater than 1000MPa to meet standard automotive specifications and for unique customer requirements. These grades were optimized by correlating chemical composition and processing parameters with microstructures and mechanical properties. Dual-Phase 980 (Stelco trademarked STELMAXTM 980DP), Multi-Phase 1180 (STELMAXTM 1180MP), Martensitic Steel 1300 (STELMAXTM 1300M) and 1500 (STELMAXTM 1500M) products met strength and formability requirements with excellent flatness and surface quality. Hydrogen quench continuous annealing technology not only ensures all developed AHSS grades have consistent mechanical properties across the entire strip length (from strip head to tail) and width (from edge to edge), but also produces high product yield compared with other continuous annealing processes.

Marine mortar was the goal material and its multi-scale physical-chemical-mechanical characteristics were the principal interest in this study. The on-line multi-scale damage detection experiments art was designed to quantify the characteristics mathematically and graphically. The normal cylinder specimen with 70-day age was produced and investigated by dynamically global MSHCT scan and local detection of EDS, SEM and XRD. The experiments results indicated that the marine mortar offered the appreciable strength at the early age at least, although some saline minerals were generated during the preparation. The micro-interfacial behavior and the parental foci controlled the damage development of the marine mortar the performance of which was still the adjustable one by the composition optimization.

This study presents a novel approach for the early detection of developing thunderstorms. To date, methods for the detection of developing thunderstorms usually rely on accurate atmospheric motion vectors (AMVs) for the estimation of cooling rate of convective clouds, which corresponds to the updraft strength of the cloud objects. In this study we present a method for the estimation of the updraft strength that does not rely on AMVs. The updraft strength is derived directly from the satellite observations in the SEVIRI water vapor channels. For this purpose the absolute value of the vector product of two vectors derived from the observed radiances emitted by the water vapor channels in 2 subsequent satellite images is calculated. The x and y components of the vectors consists of the temporal change of the spatial brightness temperature gradients in x- and y-direction, the z component consists of the temporal variation of the brightness temperature at pixel level. The absolute value of the vector product is referred to as normalized updraft strength (NUS). The performance of the method has been investigated for 2 summer periods in 2016 and 2017 by validation with lightning data. Values of the Critical Success Index (CSI) of about 66 % for the 2016 period and 62 % for the 2017 period demonstrate the good performance of the method. The POD values for the experiments with the highest CSI values are 90.3 for 2016 period and 87.6 for the 2017 period, respectively The corresponding FAR values are 28.2% (2016) and 32.5 % (2017), respectively. In summary, the method has the potential to reduce the forecast lead time significantly, and can be quite useful in regions without a well maintained radar network.

This paper addresses the effect of both microstructure and relative humidity on the long-term creep properties of sustainable calcium carbonate (CaCO₃) cements. Those can be prepared by mixing amorphous calcium carbonate and vaterite with water. A larger starting amount of vaterite, X_V, within the mixture design gives a higher elasticity and resistance to the specimens due to the larger overall bridging area within the newly formed calcite crystals. Regarding creep properties for a given relative humidity, the amplitude of creep strain decreases with X_V, and makes the relation between the elastic modulus, E, and hardness, H, of the samples to be linear with the contact creep modulus, C. On the other hand, for a given composition, the amplitude of creep increases with the relative humidity, making the contact creep modulus, Ci, to rise exponentially with the elastic modulus, E, and hardness, H, of the specimens. The most probable creep mechanisms for this kind of cement seem to be a combination of microcraking in the early stages and dissolution and reprecipitation of calcite in the long-term (also known as pressure solution theory). The presence of water in pores with increasing relative humidity might enhance the local dissolution of calcite, and hence the creep amplitude.

In this investigation dyeing of alginate fiber was carried out after cationic treatment of EPTAC (2, 3-Epoxypropyl Trimethyl Ammonium Chloride). Optimum dyeing process and parameter show good dyeing performance when alginate fiber dyed with rhubarb dye. In addition to cationic treatment is taken into account for alginate fiber to improve fastness, color strength, breaking strength. Later in dyeing for fixation ferrous sulfate, copper sulphate was considered as mordents. Moreover using pre-mordanting methods conveyed the dyeing of alginate fiber with the stave of metallic mordant and without metallic salt mordents. The evaluation of each color dyed material was done through following two terms for instance CIELAB (L*, a*, and b*) and K/S values. According to AATCC test methods color fastness to washing of the dyed fiber was determined whereas according to the ASTM D3822M standard the breaking strength of alginate fiber was estimated and tested. When dyeing was carried out on alginate fiber through considering optimum parameter like 80◦C for 90 min, M: L 1:40 and at pH 7 which showed optimum results. In addition to mostly very good wash fastness was obtained while there was no fading of the color, whereas the moderate level of color fastness to crocking was achieved. Later after dyeing the evaluations of SEM of the cationized alginate fiber and FTIR of powder from the rhubarb dye were observed. The results suggested that the surface of cationized alginate fiber was smoother than the raw alginate fiber.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

In the recent concrete industry, high fluidity concrete is being widely used for the pouring of dense reinforced concrete. Normally, in the case of high fluidity concrete, it includes high binder contents, so it is necessary to replace part of the cement through admixtures such as fly ash to procure economic feasibility and durability. This study shows the mechanical properties and field applicability of high fluidity concrete that using mass of fly ash as alternative materials of cement. The high fluidity concrete mixed with 50% fly ash was measured to manufacture concrete that applies low water/binder ratio to measure the mechanical characteristics as compressive strength and elastic modulus. Also, in order to evaluate the field applicability, high fluidity concrete containing high volume fly ash was evaluated that fluidity, compressive strength, heat of hydration and drying shrinkage of concrete.

This study examined the effectiveness of virtual delivery of the Strength at Home (SAH) intervention program for intimate partner violence in a sample of 605 military Veterans across 69 Veterans Affairs (VA) Medical Centers through a national implementation of the program. Outcome measures included physical IPV, psychological IPV, coercive control behaviors, posttraumatic stress disorder (PTSD) symptoms, and alcohol misuse. Significant pre-intervention to post-intervention reductions were found for all outcomes, with similar effect size estimates relative to a prior investigation of in-person delivered SAH through the same national VA implementation. Study findings suggest that virtual delivery of SAH may be as effective as in-person delivery which has important implications for program access and impact.

This review explores the prevalence and implications of muscular power and dynamic balance asymmetry among soccer players, focusing on its impact on performance and injury risk. Asymmetry is common in soccer due to the sport's specific demands, such as the frequent use of one leg for kicking and passing. While some asymmetry may allow for functional specialization and may not impair performance, significant imbalances are often linked to an increased risk of injuries, particularly to the lower extremities. Dynamic balance asymmetry is also associated with a higher risk of non-contact injuries, highlighting the importance of joint stability in preventing such injuries. However, the direct impact of balance asymmetry on performance metrics like sprint speed and agility is less definitive, suggesting that compensatory mechanisms or training adaptations might mitigate potential negative effects. Advancements in assessment technologies, such as motion capture systems and wearable devices, have enhanced the precision of asymmetry evaluations, enabling more targeted interventions. Despite these technological advancements, further research is needed to understand the long-term effects of asymmetry across different player demographics, including youth and female athletes, and to evaluate the effectiveness of specific training interventions. This review recommends a multidisciplinary approach, integrating biomechanics, sports medicine, and coaching insights, to develop comprehensive strategies for managing asymmetry in soccer. Such strategies will be crucial for optimizing player performance, minimizing injury risk, and improving training and rehabilitation programs tailored to the diverse needs of soccer players.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

Frailty syndrome, a significant contributor to morbidity and mortality in older adults, has traditionally been addressed through aerobic exercises. However, recent research has highlighted the importance of anaerobic and strength training activities in mitigating frailty. This article explores the shift from aerobic to anaerobic/strength training exercises, emphasizing the benefits of the latter in improving muscle strength, balance, and overall physical function. The discussion includes the physiological mechanisms underlying this shift, the evidence supporting strength training, and practical recommendations for implementation.

There are few results about the internal damping ratio of normal and high strength concretes. Hence, this paper presents the expansion of the investigation about internal damping ratio under undamaged and damaged conditions, for usual concretes (NSC) and high strength concretes (HSC). In this way, the study cover a strength range of 42 to 83 MPa. Cyclic load was employed by a servo-controlled hydraulic testing machine and for each cyclic step the dynamic elastic modulus (Ed) and internal damping ratio (ξ) were determinate by acoustic tests. Normal strength concretes (fc = 42MPa) presented undamaged internal damping ratio ξ = 0.5% and achieved the maximum value of ξ = 2.5 for a damage index equal to 0.8. High strength concretes mixtures (fc = 83MPa) presented an undamaged internal damping of ξ=0.29% and maximum internal damping equal to ξ=0.93% (under damage index of 0.32). Porosity and the transition zones were the responsible to the initial internal damping values and how the material behavior under each cyclic load. The progressive damage generates the increase of coulomb damping. There are few studies allowing the quantification and comprehension of internal damping ratio under damage cyclic loading and this approach will lead to improve the understanding of NSC and HSC under dynamical excitation subject to damage evolution, mainly in impact situations.

The present study seeks to assess the Brand Equity in the network of new fashion designers in the Canary Islands. To this end, we have adapted the Brand Equity model to an online context and proposed a set of metrics for four dimensions: estimate, relevance, awareness, and differen-tiation. The multidimensional approach to online Brand Equity was employed to measure the online Brand Equity of 129 fashion designers from the Canary Islands. The study's findings re-vealed that the number of social media profiles significantly impacts brand awareness and dif-ferentiation. Moreover, the digital maturity level influences brand relevance and overall Brand Equity . Our study highlights the practical value of web data-driven metrics for measuring online Brand Equity , which can be utilised for diagnostic, evaluative, or predictive purposes. The study's outcomes have substantial implications for marketers in the fashion industry aimed at improving online Brand Equity

In view of the fact that the field monitoring information can more intuitively and accurately reflect the stability state of slopes, this paper takes the warning threshold of slope deformation rate monitoring as the slope stability evaluation standard, and puts forward a method for solving the safety coefficient of rocky slopes. The discrete element method 3DEC, which is suitable for rocky slopes, is selected as the numerical calculation tool, and the convergence criterion of its strength reduction method is modified to the slope deformation rate threshold, and the method is realized by the bifurcation method through its built-in FISH programming language. The results of the classical case show that, by selecting the slope deformation rate threshold in the appropriate interval, the results of this paper's method are very close to those of the finite unit stress method and the limit equilibrium method, which verifies the reliability of this paper's method. Further, the method of this paper is applied to an open-pit mine slope project, based on the slope deformation on-site monitoring data, through the time series prediction method to determine the slope deformation rate warning threshold, using the threshold as an evaluation criterion to solve the slope's coefficient of safety, the calculation results show that: the slope's coefficient of safety in natural working conditions is 1.086, basically stable, suffered from continuous rainfall, the slope body is gradually saturated, the slope's coefficient of safety is reduced to 0.987, the slope's safety is reduced to 0.987. After continuous rainfall and gradual saturation of the slope, the coefficient of safety decreased to 0.987, destabilizing and destroying, which is consistent with the site conditions.

Background Sarcopenia is a state with progressive and generalized loss of skeletal muscle mass and strength. It is a serious complication occurring in chronic kidney disease (CKD) patients which increases morbidity and mortality rate. Sarcopenia is diagnosed when loss of both compartments - muscle strength and skeletal muscle quality or quantity are present. However, there are still numerous patients, also with CKD, diagnosed as pre-sarcopenic individuals with low muscle strength and normal skeletal muscle quality or quantity and conversely, with correct muscle strength and decreased skeletal muscle mass, who are prone to develop sarcopenia in future life. It is crucial to examine numerous variables possibly associated with changes of skeletal muscle mass and muscle strength in terms of preventing the development of sarcopenia. The aim of the study was to investigate anthropometric and clinical correlates and sources of variation in both skeletal muscle mass and muscle strength in advanced stages of CKD. Methods The study sample consisted of 84 non-dialysis dependent patients of both sexes (including 45.2% of women) with eGFR < 45 ml/min/1.73m²: 26.2% with eGFR 30-44 mL/min/1.73 m², 65.5% with eGFR 15-29 mL/min/1.73 m² and 8.3% with eGFR < 15 mL/min/1.73 m². Muscle strength was estimated by measuring hand grip strength (HGS) with the use of handheld hydraulic dynamometer. Muscle quantity was measured by bioimpedance spectroscopy using Body Composition Monitor. Appendicular skeletal muscle mass (ASM) was calculated according to Lin’s formula. Serum creatinine, urea, uric acid and albumin were measured. Results In bivariate analysis we found that ASM significantly and positively correlated with anthropometric variables such as body mass (r=0.903, p<0.001), NH weight (r=0.882, p<0.001), height (r=0.694, p<0.001), body mass index (BMI) (r=0.701, p<0.001), lean tissue mass (LTM) (r=0.664, p<0.001), lean tissue index (LTI) (r=0.433, p<0.001), fat mass (r=0.614, p<0.001) and fat tissue index (FTI) (r=0.449, p<0.001), and was negatively associated with clinical variable such as hydration status (p<0.001). HGS significantly and positively correlated with anthropometric parameters such as body mass (r=0.319, p=0.003), NH weight (r=0.315, p=0.004), height (r=0.666, p<0.001), LTM (r=0.490, p<0.001), LTI (r=0.238, p=0.029), and ASM (r=0.501, p<0.001), and was negatively associated with clinical variables like uric acid (p=0.039) and urea (p<0.001). After adjustment for age, sex and height, HGS remained significantly and negatively related with uric acid (β=-1.078, p=0.041) and hydration status (β=-0.805, p=0.042). Conclusions In CKD patients, ASM is determined mainly by anthropometric parameters but HGS - both by anthropometric and clinical variables specific for CKD.

The aim of the study was to examine the influence of different irrigation protocols on the shear bond strength (SBS) of self-adhesive resin composite cement (SARC) to primed radicular dentin. Radicular dentin slabs (N=58) were sectioned from extracted intact third molars, embedded in acrylate, polished, and randomly assigned to five experimental groups (N=8-12) and one control group, CG (N=8). Irrigation solutions used were sodium hypochlorite (H), ethylene-diamine-tetra acetic acid (EDTA), etidronic acid with hypochlorite (HEDP), saline solution (SS), and chlorhexi-dine (CHX). Each experimental group underwent different irrigation protocol for two minutes: 1) H/EDTA/H, 2) HEDP, 3) H/EDTA/CHX, 4)H/EDTA/SS, and 5) HEDP/SS. The CG samples were not treated with any irrigation solution. After drying, adhesive enhancing primer (AEP) and du-al-curing SARC were applied to the radicular dentin using molds corresponding to the Ultra Tester. Specimens were stored at 37°C in distilled water and fractured in shear mode after 10 days. The results were analyzed using the ANOVA statistical test and Post-hoc Games-Howell test, α=0.05. CG exhibited the highest SBS. Except for HEDP and HEDP/SS, all experimental groups showed significantly lower SBS compared to the control group (p< 0.05). HEDP seems to be ad-equate solution for root canal cleaning before dentin priming and fiber post cementation with self-adhesive resin cement. Cleaning protocols with H, EDTA and CHX cause a significant de-crease in bond strength.

The influence of aluminosilicate pozzolanic waste, specifically spent fluid catalytic cracking catalyst (FCCW) and metakaolin waste (MK) from expanded glass industry, on the properties of hardened Portland cement paste were analysed. The study involved replacing part of cement with FCCW and MK and observing their impact on hydration, microstructure, density and compressive strength of hardened cement paste. Various analysis methods were employed, including X-ray diffraction (XRD), thermogravimetric analysis (TG), and scanning electron microscopy (SEM), to understand the changes in the structure of hardened cement paste during hydration. The findings revealed that FCCW tends to accelerate cement hydration process due to its high surface area and pozzolanic activity. Notably, the formation of portlandite crystals was observed on FCCW particle surfaces in a specific direction. These crystals appeared smaller and developed in different directions in compositions containing a composite binder with mixture of FCCW and MK in a ratio 1:1. This could be influenced by pozzolanic reactions activated by fine particles of MK and the formation of calcium silicate hydrates (CSH) and calcium alumino silicate hydrates (CASH) in the presence of portlandite. XRD and TG results indicated that the specimens containing a composite binder exhibited the least amount of portlandite. The compressive strength of these specimens increased compared to control specimens, although the amount of cement was 9% lower.

Protein–nanoparticle hybridization can ideally lead to novel biological entities characterized by emerging properties, which can sensibly differ from those of the parent components. Herein, the effect of ionic strength on the biological functions of recombinant, His-tagged spermine oxidase (i.e., SMOX) was studied for the first time. Moreover, SMOX was integrated to colloidal surface active maghemite nanoparticles (SAMNs) by direct self-assembly, leading to a biologically active nano-enzyme (i.e., SAMN@SMOX). The hybrid was subjected to an in-depth chemical-physical characterization highlighting that protein structure was perfectly preserved. The catalytic activity of the nanostructured hybrid (SAMN@SMOX) was assessed by extracting kinetics parameters using spermine as substrate and compared to the soluble enzyme as a function of ionic strength. Results revealed that the catalytic function was dominated by electrostatic interactions and that they were drastically modified upon hybridization with colloidal ɣ-Fe2O3. Noteworthy, the affinity of SMOX toward spermine was significantly higher for the nanohybrid at low salinity. The present study supports the vision of using protein–nanoparticle conjugation as a mean for modulating biological functions.

The aim of this study was to investigate the effect of laser irradiation to computer-aided de-sign/computer-aided fabrication (CAD/CAM) resin blocks coated with a silane coupling agent on the bond strength between the resin blocks and composite resin. The CAD/CAM resin blocks used in this study were Cerasmart 300 (GC) and Vita Enamic (Vita); they were cut into plates and then subjected to a series of treatments. After processing with a silane coupling agent, treatment with a semiconductor laser was performed at 3.0, 5.0, and 7.0 W, followed by the bonding procedures. The control group included those exposed to silane and bonded without laser application. After bonding, a mold with a simulated cavity was formed on the specimen and filled with flowable composite resin, and they were stored for 24 h or stressed by thermal cycling for subsequent testing that assessed the shear bond strength (n = 10). The results revealed that the bond strength was significantly enhanced by laser irradiation after applying a silane coupling agent, whereas significant effect was not detected between the materials. Particularly, 7 W laser irradiation had a significant effect on the bond strength between the composite resin and Cerasmart block after thermal cycling.

The development of the additive manufacturing (AM) technology proffers challenging requirements for forming accuracy and efficiency. In this paper, a hybrid additive manufacturing technology combining fusion-based selective laser melting (SLM) and solid-state cold spraying (CS) was proposed in order to enable the fast production of near-net-shape metal parts. The idea is to fabricate a bulk deposit with a rough contour first via “fast” CS process and then add fine structures and complex features through “slow” SLM. The experimental results show that it is feasible to deposit SLM part onto CS part with good interfacial bonding. However, the CS parts must be subject to heat treatment to improve their cohesion strength before being sending for SLM processing. Otherwise, the high tensile residual stress generated during SLM process will cause fracture and cracks in the CS part. After heat treatment, pure copper deposited by CS undergoes grain growth and recrystallization, resulting in improved cohesive strength and release of the residual stress in the CS parts is released. The tensile test on the SLM/CS interfacial region indicates that the bonding strength increased by 38% from 45±7 MPa to 62±1 MPa after the CS part is subject to heat treatment, and the SLM/CS interfacial bonding strength is higher than the CS parts. This study demonstrates that the proposed hybrid AM process is feasible and promising for manufacturing free-standing SLM-CS components.

Background: Radiotherapy is an important part of the medical therapy concept treating tumors in the head and neck region; however, the impact on the field of dentistry could be im-mense. The objective of this study was to evaluate the microtensile bond strength (µTBS) of uni-versal adhesives and to compare the results of different application modes (etch-and-rinse and self-etch) on irradiated and sound human dentin. Methods: Dentin specimen of 180 extracted human wisdom teeth were divided in two superordinate groups. Ninety teeth received either no irradiation (control group) or the high-level therapeutic dose of 60 Gy (test group) applied frac-tionally (2 Gy/day, 5 days/week, 6 weeks). Samples from each group were randomly divided in-to six subgroups assigned to three established universal adhesives (Futurabond® U, VOCO; AdheSE® Universal, Ivoclar Vivadent; Xeno® Select, Dentsply) in both conceivable application modes: etch-and-rinse and self-etch (n = 15). Bond strength was assessed with a universal testing machine immediately after application and light curing of the adhesive materials. Statistical analysis was performed using two-way ANOVA (p<0.01) and Tukey's test (p<0.05). Results: The effect of dentin irradiation and application mode for the adhesive restoration was found to be significant (p<0.01, ANOVA). In all groups, a decrease of µTBS could be observed when used on irradiated dentin. However, no significant influence of high level radiation on the bond strength of Futurabond® U and AdheSE® Universal in both modes could be evaluated (p>0.05, Tukey´s test). Solely in the case of the adhesive system Xeno® Select, significantly reduced bond strength could be determined in self-etch mode after irradiation (group 60 Xse) compared to the control group (0 Xse) (p<0.05, Tukey´s test). Conclusions: Within the limitations of an in vitro study, some effects of high-level tumor irradiation on the bond strength of universal adhesives can be detected. However, these effects were strongly depending on the used material and application mode.

This paper presents the use of Graph Neural Networks (GNNs) to predict the tensile strength of Fused Deposition Modeling (FDM) specimens. In the present work, there are four main input parameters i.e. Infill percentage, Layer height, Print speed and Extrusion temperature while the Tensile Strength is an output parameter were considered. This study includes use of central composite design based response surface methodology to finalize the experimental layout. 3D printed specimen were manufactured as per the ASTM E8 standard on FDM printer using Polylactic Acid (PLA) as filament. Micro-tensile test were performed on the printed specimen as per ASTM E8 standard. The GNN algorithm was trained on a dataset of FDM specimens, achieving a mean squared error (MSE) of 2.47, mean absolute error (MAE) of 1.14, and R-squared value of 0.78. An adjacency matrix, which shows the connections between nodes in a graph. The obtained plot for nodes and weights in a GNN provide valuable information about the model and its performance. The results show the potential of using GNNs in predicting the mechanical properties of additively manufactured specimens and provide a promising direction for further research in this field.

This study investigates the long-term impact of soil tillage systems and crop residue incorporation on agrophysical properties. A long-term field experiment has been conducted since 1999 at the Ex-perimental Station of Vytautas Magnus University Agriculture Academy. According to the latest edition of the International Soil Classification System, the soil in the experimental field was classified as Planosol, with a silty medium loam texture at a depth of 0–20 cm and a silty light loam at a depth of 20–40 cm. This investigation aimed to assess the long-term impact of reduced tillage systems, straw, and green manure combinations on soil physical properties, including soil shear strength, and soil aggregate stability. Studies were carried out on winter wheat crops in 2014, 2017, and 2023. The treatments were arranged using a split-plot design. In a two-factor field experiment, one part of the experimental field had straw removed, while the other part had the entire straw yield chopped and spread at harvest (Factor A). The subplot factor (Factor B) included three different tillage sys-tems: conventional deep ploughing, cover cropping for green manure with no-till, and no-tillage. Soil samples were analysed in the Laboratory of Agrobiology at Vytautas Magnus University Ag-riculture Academy. The findings indicate that long-term application of reduced tillage significantly increases soil shear strength. Shallower tillage depths lead to higher soil shear strength, while the effect of spreading plant residues is relatively lower. Long-term tillage of different intensities, spreading plant residues, and catch crop cultivation for green manure did not significantly affect soil structure. However, soil structural stability was found to be highly dependent on soil tillage. Cover cropping for green manure with no-till and no-tillage positively affected soil aggregate sta-bility in the upper (0–10 cm) and 10–25 cm layers.

Limited availability of expensive alloying elements elevates low-alloyed steels to a unique position in the field of lightweight construction and mass production. Quenching and partitioning (Q&P) heat treatments of low-alloyed steels with exceptional property combinations are particularly promising. In this study, we characterize for the first time a new low-alloyed steel to be processed by Q&P heat treatments. In combined experimental and numerical studies, we design a novel approach that effectively combines the short cycle times of press hardening with the excellent property profiles of Q&P-treated steels. We identify appropriate transformation parameters for Q&P heat treatments by dilatometric studies and we adjust a number of reference conditions with different isothermal holding times. By means of SEM analysis and XRD measurements, we show that different fractions of retained austenite result in different mechanical properties. Initial numerical designs of the process can identify varying temperature profiles and cooling rates depending on the position in the die. The results show that the geometry of the part plays a minor role, but the die temperature is the dominant factor for successful partitioning directly in the press hardening process.

Selective Paste Intrusion (SPI) is an additive manufacturing (AM) process in which thin layers of aggregates are selectively bonded by cement paste only where the structure is to be produced. In this way, concrete elements with complex geometries and structures can be created. Reinforcement is required to increase the flexural strength of the concrete elements and, thus, enable their applicability in practice. Integrating the reinforcement is a difficult task, particularly in the case of SPI due to the layer-wise printing method. Especially with respect to possible complex structures, the production of the reinforcement needs to be adapted to SPI, thereby offering a high degree of freedom. One concept for a reinforcement integration is combining the two additive manufacturing processes SPI and Wire and Arc Additive Manufacturing (WAAM). However, since the two processes serve different fields of application, their compatibility is not necessarily given. Ongoing investigations show that the temperatures caused by WAAM adversely affect both, the cement paste rheology required for sufficient paste penetration into the particle bed and the overall concrete strength. This paper provides an overview of ongoing research focusing on different cooling strategies and their effects on the compressive strength of SPI-printed concrete parts.

Steel fibers (SF) and polyolefin (PF) are widely used for shotcrete, especially in tunnelling. Both SF and PF and have shown to meet the standards in order to reduce or substitute the conventional steel mesh as reinforcement of concrete showing mechanical and productive advantages. This study sought the analysis and assessment of the mechanical properties of fiber reinforced shotcrete, comparing in-situ with laboratory results. This was performed with low and high fiber dosages of SF and PF as well as a combination of them (hybrid mixtures). A total of seven mixtures, two of steel, two of polyolefins, two hybrids and a control mixture were manufactured at laboratory and in situ. By performing tests according to EN 14651 and slabs according to EN 14488-5, it was possible to characterize the residual flexural strengths (fRj), and energy absorption capacity (E25mm) in slabs. In addition, a fracture surface analysis was performed, and the orientation factor was obtained. This allowed the authors to quantify the loss of residual strength on site and correlate it with the fiber content and positioning. Moreover, some relationships between beam and slab tests were found, allowing to correlate the most relevant type of tests in the field of fiber reinforced concrete.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Nowadays, we use social networks such as Twitter, Facebook, WeChat and Weibo as means to communicate with each other and get to know others. Gradually social networks has become indispensable in our everyday life, and we cannot absolutely imagine what the daily life would be like without social networks. Through social networks, we can access friends' opinions and behaviors easily and are influenced by them in turn. Thus, an effective algorithm to find the top-K influential nodes (the problem of influence maximization) in the social network is critical for various downstream tasks such as viral marketing, anticipating natural hazards, reducing gang violence, public opinion supervision etc. Solving the problem of influence maximization in real-world propagation scenarios often involves estimating influence strength (influence probability between two nodes), which cannot directly observed. To estimate influence strength, conventional approaches propose various humanly-devised rules to extract features of user interactions, the effectiveness of which heavily depends on domain expert knowledge. Besides, they are often applicable for special scenarios or specific diffusion models. Consequently, they are difficult to be generalized into different scenarios, diffusion models and even domains. Inspired by the powerful ability of neural networks in the field of representation learning, we design a deep hierarchical network embedding model HGE to map nodes (with attributes) into latent space automatically. In general, HGE takes an attributed social network as the input for learning latent network representation of each node, incorporating hierarchical community structure, node attributes and general network structure into a unified deep generative framework. Then, with the leaned latent representation of each node, we propose a HGE-GA algorithm to predict influence strength and compute the top-K influential nodes through a greedy-based maximization algorithm. Extensive experiments on real-world attributed networks demonstrate the outstanding superiority of the proposed HGE model and HGE-GA algorithm compared with the state-of-the-art methods, verifying the effectiveness of the proposed model and algorithm.

The Study proposes possible solution to enhance Password Authentication using Association Technique based on the Ecological theory of memory and data at the Presbyterian university College Ghana. The study used a deductive research approach and employed two empirical Studies using the non-probability sampling technique where few respondents were selected in categories out of the populace by means of openness in other to get similar categories of respondents with different age groups and education background. The two Empirical study also used a quasi-experimental approach which structure incorporate observation, experimental treatment and timing. The First empirical study carried out an investigation to identify existing Password authentication Technique used by End Users, as well as their behavior in password utilization through a self-completed questionnaires which was analyzed using SPSS version 21 . The Second empirical study was an experiment to compared three kinds of password constructions that is own set, modified dictionary, and association against one another to see which of them would be best meet the ecological theory of memory and data which aims at creating a secured password that is easy to recall. The computation and evaluation of password construction was done using My1login Password meter whiles Levenshtein Distance String Edit Software was also used to compute the memorability of all given password. Across-tabulation was then employed out of the experiment using SPSS version 21. The result from the analysis revealed that the majority of the respondents do have weak passwords and also have few passwords which they even end up sharing with families and friends and reuse it. This confirms statements made by researchers that human being is the weakest connection in information system securities. To maintain Confidentiality, Availability and Integrity of data, the study therefore recommended the use of the Association Password technique which makes it easier to develop a much secured password that is difficult to crack but easy remember.

We prepared heterogeneous alumina-silicate glasses by consolidating nanoparticles using molecular dynamics simulations. Consolidated glasses from either low alumina content alumina-silicate glasses or high alumina content alumina-silicate glasses show significantly improved ductility around consolidation pressure of ~3 GPa. The introduced structural heterogeneities, namely over-coordinated network formers and their neighboring oxygen atoms, are identified as plasticity carriers due to their high rearrangement propensity. In addition, consolidated oxide glass from both 23.4Al₂O₃76.6SiO₂ and 73.1Al₂O₃26.9SiO₂ nanoparticles show improved flow strength (up to 1 GPa) due to the introduction of chemical heterogeneities. Last but not least, apparent hardening behavior appears upon cold work in consolidated glasses, with an increase of yield strength from ~3.3 GPa to ~6.4 GPa. This method is a big advancement toward ultra-strong and ultra-tough glasses by breaking the structure, composition and size limitations in traditional melt-quench process.

Current study aims to evaluate the possibilities to increase part strength by optimizing the FFF process parameters. Five different CAD models of parts with same coupling dimensions but different shape inherited from a recent study were converted into test samples with Ultimaker 2 3D printer. The main measure of success was the sample strength, defined as the load at which the first crack in the stressed area of the part appeared. Three different modifications to the FFF process with verified positive effect on interlayer bonding were applied. First modification included raising the extrusion temperature and disabling printed part cooling. Second modification consisted in reduction of the layer thickness. Third modification combined the effects of the first and the second ones. For four out of five shapes tested applied process modifications resulted in significant strengthening of the part. The shape that exhibited the best results was subject to further research by creating special printing mode. The mode included fine-tuning of three technological parameters on different stages of the part fabrication. As result it was possible to increase the part strength by 108% only by tuning printing parameters of the best shape designed with increasing its weight by 8%.

The article describes the study of the properties of polytetrafluoroethylene, modified using natural layered silicates—serpentinite. It is shown that the introduction of a small amount of layered silicates significantly increases the tribological characteristics of the material. The additional introduction of magnesium nano-spinels facilitated the formation of an intercalated polymer-silicate nanocomposite.

Present work has systematically investigated the evolution of dispersoid and elevated-temperature properties including the strength and creep resistance during the various multi-step heat treatments in Al-Mn-Mg 3004 alloys. Results show that only α-Al(MnFe)Si dispersoid is observed in the studied temperature range (up to 625°C) and it coarsens with increasing temperature to 500°C but dissolves at 625°C. The evolution of elevated-temperature strength and creep resistance is greatly related to the temperature of each step during the multi-step heat treatments. Generally, lower temperature at the first-step heat treatment leads to higher properties while the properties decrease with increasing temperature of last-step heat treatment. Suitable models have been introduced to explain the evolution of strength and the creep threshold stress at elevated-temperature during the various heat treatments.

Background: Even though a number of studies have verified the positive effect of physical activity (PA) on self-related health (SRH) no previous research has examined this association among pediatric patients with Type 1 diabetes mellitus (T1DM). Objective: The purpose of this study was to investigate the association between regular physical activity (PA) and self-rated health (SRH) in pediatric patients with Type 1 diabetes mellitus (T1DM) who lacked diabetes care. Methods: We conducted a retrospective study among pediatric patients with T1DM who lacked diabetes care and were enrolled in a diabetes education program between January 2011 to January 2015 at the endocrinology clinic of Seoul National University Children’s Hospital in South Korea. The eligible participants for this study were 37 pediatric patients with T1DM aged 9 to 17 years. PA was divided into regular PA and muscle strength exercise to analyze the relationship with SRH using binomial logistic regression analysis. Results: The results showed SRH of pediatric patients with T1DM who did not engage in regular PA was significantly lower than those who did (OR in regular PA = .199 [95% CI: .040, .995]; OR in regular muscle strength exercise = .097 [95% CI: .023, .825]). Conclusions: In conclusion, regular PA and muscle strength exercise in pediatric patients with T1DM who lacked diabetes care were effective in improving their SRH. A systematic plan is required to enhance regular PA for pediatric patients with T1DM.

Although fragility fractures, osteoporosis, sarcopenia and frailty are becoming more prevalent in our aging society the treatment options are limited and preventative strategies are needed. Despite magnesium being integral bone and muscle physiology the relationship between dietary magnesium and skeletal muscle and bone health has not been investigated concurrently before. We analysed cross-sectional associations between dietary magnesium and skeletal muscle mass (as fat free mass – FFM), grip strength and bone density (BMD) in 156,575 men and women aged 39-72 years from the UK Biobank cohort. FFM was measured with bioelectrical impedance and expressed as the percentage of body weight (FFM%) or divided by body mass index (FFM_BMI). Adjusted mean grip strength, FFM%, FFM_BMI, and BMD were calculated according quintiles of dietary magnesium, correcting for covariates. Significant inter-quintile differences across intakes of magnesium existed in men and women respectively of 1.1% and 2.4% for grip strength, 3.0% and 3.6% for FFM%, 5.1% and 5.5% for FFM_BMI, and 2.9% and 0.9% for BMD. These associations are as great or greater than annual measured losses of these musculoskeletal outcomes indicating potential clinical significance. Our study suggests that dietary magnesium may play a role in musculoskeletal health and have relevance for population prevention strategies for sarcopenia, osteoporosis and fractures.

: The present paper tackles the important issue of tensile ultimate strength of ceramic matrix composites, using a multiscale approach. The ultimate strength is investigated at the successive increasing length scales inherent to 2D woven SiC/SiC composites, i.e. single filaments, fiber tow, minicomposites reinforced with a single tow, and 2D woven composite. First experimental results on tensile behavior under strain-controlled conditions are summarized for tows, minicomposites and composites. Then, models of tow ultimate failure under controlled force and strain are presented. A criterion of tow failure is developed for filament fracture initiation and then propagation based on applied stress and on filament strength gradient. The model of ultimate failure of minicomposite under strain-controlled condition is based on the strength of filaments in the presence of matrix cracks and the overstress induced by interactions of broken filaments and the matrix. The variability of ultimate strengths of filaments, minicomposites and composites at various gauge lengths is described by linear p-quantile diagrams which indicates that the data follow normal distribution function. The contribution of structural effects to variability of composite and minicomposite strength under strain-controlled loading is analyzed. Their dependence on specimen size is related to reproducibility of critical flaw population and structural effects.

We investigated theoretically the electron-surface optical phonon interaction across the long-range Fröhlich coupling in monolayer transition metal dichalcogenides such as WS2, WSe2, MoS2, and MoSe2 monolayers on SiC and hexagonal BN dielectric substrates. We employed the effective Hamiltonian in the 〖K_(+ ) (K〗_-) valley of the hexagonal Brillouin zone, to assess electronic energy shifts induced by the interaction between electronic states and surface polar optical phonons. Our results indicate that the interaction between electron and surface optical phonon depends upon the polar nature of the substrate. We have also calculated the polaronic oscillator strength as well as the polaronic scattering rate of the lower polaron state in monolayer WS2, WSe2, MoS2, and MoSe2 on SiC and hexagonal BN dielectric substrates. As a result, we have proved theoretically; firstly, the enhancement of polaronic scattering rate with temperature, and secondly, the notable influence of the careful selection of surrounding dielectrics on both Polaronic oscillator strength and polaronic scattering rate. Thus, the optimal dielectrics would be those exhibiting both elevated optical phonon energy and a high static dielectric constant.

There is lacking information about the physiological response when conducting training of older men in a real-life setting. Seventy-six sedentary men aged 72.3 ± 0.6 (means ± SE; range: 63–92) years with a height, body mass and body mass index of 178.9 ± 0.8 cm; 92.1 ± 2.2 kg: 28.7 ± 0.6 kg/m2, respectively, were recruited to floorball (FG, n = 29), strength (SG, n = 38) or bowls (BG, n = 9) training 1 h twice a week in municipal activity centers and senior sport clubs. Subjects were tested at baseline, after 12 and 24 weeks. Twelve weeks of floorball and strength training lead to reduced blood Hb1Ac, body mass, fat mass, visceral and android fat. Further, SG had a decrease in gynoid fat and blood total and LDL cholesterol. Both groups decreased heart rate at rest. In SG, systolic and diastolic blood pressure were also reduced. FG increased markers for bone growth. FG and SG improved functional capacity. The improvements in FG and SG were maintained after 24 weeks. BG did not have any changes. In conclusion, older men conducting floorball or strength training twice a week in a real-life setting can improve functional capacity and a high number of health factors, whereas playing bowls does not lead to physiological changes.

Background: Despite the tremendous effort in hamstring injury prevention, injury rates in soccer remain elevated. Hypothesis: Hamstring and hip/pelvic isometric strength imbalances may increase the likelihood of hamstring strain injury (HSI) occurrence amongst soccer players.Study design: Case-control study.Methods: In 120 male soccer players (mean age: 20.0 +/- 6.96 years) pre-season maximum isometric strength of the hip adductors, abductors, flexors, and knee flexors were measured, and strength ratios were calculated. Previous injury and anthropometric data were registered. Injury data were collected following the FIFA/UEFA consensus. A multivariate and Machine learning-based Logistic Regression model was employed to estimate the likelihood of players sustaining a hamstring injury.Results: 21 players sustained 32 hamstring injuries. Players with higher abduction strength in the dominant leg had an 18.5% lower risk of sustaining a hamstring injury (OR = 0.818, CI 95% = [(0.695-0.964]). No other significant contributor variables were found to be significant predictors of hamstring injury in the player group (p> 0.05).Conclusion: Isometric strength of the abductor muscles in the dominant limb had a significant association with hamstring injury.Clinical relevance: Our findings indicate the utilization of hip strength measurements as an integral component of the pre-season screening assessment, thereby affirming prior research on the correlation between lumbo-pelvic stability and incidence of hamstring injuries. Consequently, clinicians should contemplate incorporating hip strengthening exercises into regular training sessions, rehabilitation programs, and injury prevention protocols especially indicated when lower hip strength levels are observed.

Cementitious materials exhibit excellent binding properties and micropore structures that support the stabilization of TiO2 nanoparticles within the matrix. Therefore, these materials are ideal for the development of functional construction products with TiO2 nanoparticles. This study investigated the degree of hydration, microstructure, and mechanical properties of cement-containing TiO2 nanoparticles. The experimental results demonstrated that TiO2 nanoparticles accelerated the hydration rate of cement, reducing the setting times. Moreover, TiO2 nanoparticles changed matrix microstructure, decreasing the porosity and improving early-age strength. Although TiO2 nanoparticles function as nucleation sites in the cement hydration reaction, the tendency of the particles to clump implies that proper dispersion should be ensured when mixing in large quantities. When developing new building materials incorporating TiO2 nanoparticles, considering the effect of TiO2 nanoparticles on the hydration reaction of cementitious materials is crucial.

Despite ongoing efforts, the relationship between groin strength and injury remains unclear. The challenge of accurately predicting injuries presents an opportunity for researchers to develop pre-vention strategies to reduce the occurrence of such injuries. Consequently, this issue requires further investigation to obtain insights into effective mitigation strategies. In 120 male soccer players the maximum isometric strength of the hip muscle groups was measured, and the strength ratios were calculated. Previous injury and anthropometric data were registered. Injury data were collected following the FIFA/UEFA consensus. The K- Nearest Neighbour (k-NN), was used to predict the incidence of injury, while the significant predictive variables of the k-NN algorithm were fitted into a multivariate logistic regression model (LR) to analyze the likelihood of players sustaining a groin injury. The LR model determined two variables as significant predictors of groin injury. Players were less likely to sustain a groin injury by 76% for each decrease of the Adductors/Abductors isometric strength ratio in the non-dominant limb (OR = 0.238, CI 95%= [(0.098-0.572]). Players with a history of previous injury had a 67% greater risk of sustaining an injury (OR = 0.333, CI 95%= [(0.1068-1.038]). Isometric hip adductor and abductor strength im-balances of the non-dominant lower limb and a history of previous injury were risk factors for groin injury in soccer players.

Efficient utilization of biomass requires conversion into forms that can be optimally applied in energy generation. Briquetting involves compaction of biomass into solid blocks that are more efficient than raw biomass and provides for ease of transport and handling. These are improved when the briquettes possess high shatter index and compressive strength. Due to difference in nature and composition, it is imperative to define optimum conditions for the production of quality and durable briquettes for individual biomass compacted into briquettes. This study studied the effects of process variables on the strength and durability of biomass briquettes produced using Abura sawdust. The lateral compressive strength and drop shatter index were investigated whilst varying the temperature (100-150 °C), pressure (9-15 MPa) and hold time (15-30 min). The compressive strength ranged between 2.06 and 5.15 MPa whilst the shatter index was between 50 and 600. The pressure was significant to the determination of the compressive strength (p &lt; 0.1) and the shatter index (p &lt; 0.05). Mechanical characteristics of the binderless Abura sawdust briquettes can be improved by optimizing the densification variables during the briquetting process when moderate pressures are used for compaction.

Addressing the issue of low bonding strength in Ti/Mg laminated composites due to interfacial oxidation, this study employs a differential temperature rolling method using longitudinal induction heating to fabricate Ti/Mg composite plates. The entire process is conducted under an argon gas protective atmosphere, which prevents interfacial oxidation while achieving uniform deformation. The effects of reduction on the mechanical properties and microstructure of the composite plates are thoroughly investigated. Results indicate that as the reduction increases, the bonding strength gradually increases, mainly attributed to the increased mechanical interlocking area and a broader element diffusion layer. This corresponds to a transition from brittle to ductile fracture at the microscopic tensile-shear fracture surface. When the reduction reaches 47.5%, the Ti/Mg interfacial strength reaches 63 MPa, which is approximately a 20% improvement compared to the bonded strength with previous oxidation at the interface. Notably, at a low reduction of 17.5%, the bonding strength is significantly enhanced by about 1 time. Additionally, it is found that a strong bonded interface at high reduction is beneficial in hindering the propagation of interfacial cracks during tensile testing, enhancing the ability of the Ti/Mg composite plates to resist interfacial delamination.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

This article objective was to identify a centenary trend in the growth and development of girls in the metropolis of Moscow. Material and methods — The physical development (body length and weight, chest circumference, right hand muscle strength, and menstrual function development) of Moscow girls was studied during the period from 1920 to 2020. The amount of own observations was 4581 girls aged 8-17 years. Results – A comparative analysis of the physical development of Moscow school girls of different decades revealed a statistically significant increase in body length by 3-5 cm and a significant increase in chest circumference in all age groups of girls of the beginning of the XXI century, compared with their peers in the 1960s and 1980s, which indicates the completion of the gracialization processes that have been observed since the 1980s. However, in all age groups, a decrease in the muscle strength of the right hand is still being noticed. Earlier terms of menarshe onset in modern Moscow school girls (12 years 9 months) and a shift in growth jumps to earlier terms were established. It is shown that the age of menstruation depends on the level of family wealth. Conclusions. In Moscow girls in the centenary dynamics, a tendency to increase the total body size and shift the terms of biological maturation to earlier terms was revealed.

The research object was the stress-strain state of shear stud bonds in the contact joint of steel-concrete beams. The work diagrams for three types of anchors are given. Based on the analysis of numerical and full-scale experiments, analytical dependencies are proposed that reflect the actual operation of anchor ties. Comparisons of the calculation results by analytical formulas and comparisons with numerical and full-scale experiment data are given. Numerical studies have revealed the pattern of the stress-strain state of the contact joint, the stages of development of cracks in the concrete flange, and the sequence of development of deformations in anchor ties. It was revealed that vertical shear studs bonds have an increased bearing capacity, although displacements are 1.5-2 times greater than those of loop-shaped anchor ties.

Fastener holes are among the most common natural stress concentrators in metal structures. The life cycles of various structural elements, such as those in aircraft structures, automobiles, and rail-end bolt joints are limited by fatigue damage around the holes. An effective approach to delay the formation and growth of fatigue macrocracks is to introduce residual hoop compressive stresses around the holes. Two methods have become established in the prestressing of fastener holes in aircraft components: split sleeve and split mandrel, which implement one-sided processes. The common disadvantage of both methods is the complex procedure due to the need for high accuracy of the initial holes. This article presents a new modified split mandrel method providing the same tightness (interference fit) with a wide tolerance of the pre-drilled hole diameters reducing the number of technological cycle steps and production costs. То implement the new method, a functionally connected tool and a device with a hydraulic drive were developed. An extensive experimental study of 2024-T3 AA specimens was carried out to evaluate the effectiveness of the method under a high scattering of the pre-drilled holes. The new method provided a deep zone of residual hoop compressive stresses on both faces of the specimens after cold working and after hole final reaming. The removal of a plastically deformed layer around the hole of suitable thickness during the final reaming decreased the axial gradient of residual hoop stress distribution. Fatigue tests on a tensile pulsating cycle verified the effectiveness of the modified split mandrel method to significantly increase the fatigue life by 6.6 times based on cycle fatigue strength compared to the conventional case of machining the holes. The obtained S-N curves for three groups of samples with initial hole diameters of 8.0, 8.1, and 8.2 mm which were cold worked with the same tightness of 0.32 mm and final reamed, aligned well indicating that the new method can provide constant fatigue strength for a given stress amplitude.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

Experimental methodologies for fatigue lifetime prediction are time-intensive and susceptible to environmental variables. While the cohesive zone model is popular for predicting adhesive fatigue lifetime, entropy-based methods have also shown promise. This study aims to provide an understanding of the durability characteristics of CFRP adhesive joints by incorporating an entropy damage model within the context of the finite element method (FEM), examined the effects of different adhesive layer thicknesses on SLS models. As the adhesive layer increased in thickness, DAMAGE VARIABLES initially rose and then declined, peaking at 0.3mm. This finding provides crucial understanding into the stress behavior at the resin-CFRP interface and the resin's fatigue mechanisms.

The regenerated magnesia-calcium brick samples that had added 0, 1.5, 3.0 wt.% aluminium oxide (Al2O3) were prepared by using spent magnesia-calcium bricks, fused magnesia and Al2O3 powder additive as the main raw materials. The phases, microstructures, room temperature and hot flexural strength, resistance to cement clinker corrosion and strength of coating adherence were investigated respectively. It indicated that the addition of Al2O3 increased mainly resulting in the content of tetracalcium aluminoferrite (C4AF) and tricalcium aluminate (C3A) increased in the regenerate samples. The bulk density, the room temperature flexural strength and the strength of coating adherence all increased, while the hot flexural strength and corrosion resistance both deteriorated along with the increase of Al2O3 addition. It was because that on the one hand the low melting point phases of C4AF and C3A improved the sinterability of the regenerated samples during the burning stage, on the other hand they melted or existed in liquid phase during the experimental temperature (1573 K and 1823 K) which degraded hot flexural strength and corrosion resistance, and enhanced the strength of coating adherence as the wettability of the liquid phase. The content of Al2O3 in the regenerated magnesia-calcium brick should not be higher than 1.1 wt.%, considering its room and high-temperature performances for cement rotary kiln.

Polyimide (PI) films are widely used in electronic devices owing to their excellent mechanical and electrical properties and high thermal and chemical stabilities. In particular, PI films play an important role in flexible printed circuit boards (FPCBs). However, one challenge currently faced with their use is that the adhesives used in FPCBs cause a high dielectric loss in high-frequency applications. Therefore, it is envisioned that PI films with a low dielectric loss and Cu films can be used to prepare two-layer flexible copper clad laminates (FCCLs) without any adhesive. However, the preparation of ultra-thin FCCLs with no adhesives is difficult owing to the low peel strength between the PI films and Cu films. To address this technical challenge, an FCCL with no adhesive was prepared by high-power helicon wave plasma (HWP) treatment. The surface roughness of the PI film and the peel strength between the PI film and Cu film were measured. The experimental results showed that the surface roughness of the PI film increased by 40-65% and the PI film demonstrated improved adhesion (the peel strength was &gt;8.0 N/cm) with the Cu film following plasma treatment and Cu plating.

The article presents a simplified method for determining the strength of a corrugated board packaging subjected to dynamic transport loads. The proposed algorithm consists of several calculation steps: (1) a static analysis of the compressive strength of the package, (2) an analysis of random vibrations in the frequency domain, used to determine the resonance frequencies, and (3) a dynamic analysis of the package loaded with computed resonant frequencies. For this purpose, numerical models of the static compression test of the packaging before and after the dynamic analysis of the package subjected to general transport loads were developed. In order to validate the model, the laboratory packaging compression tests were also performed for samples of boxes with 3-layer cardboard. Thanks to this, it was possible to verify the results of numerical simulations of compression tests for several box geometries. Which, in turn, allowed for the development of a method based on dynamic and post-dynamic (static) numerical analysis, allowing to determine with high accuracy the resistance of selected packaging to vibrations and dynamic loads. The results of the (validated experimentally) numerical analysis prove the usefulness of the simplified method presented here for precise estimation of the load capacity of various packages dynamically loaded during transport.

Abstract: To overcome the environmental impact of cement production in cocnrete , the construction industry is adopting eco-friendly approaches, such as incorporating alternative and recycled materials, minimizing carbon emissions in concrete production. One such material that has gained prominence is Ground Granulated Blast Furnace Slag (GGBFS),. This study focuses on investigating the compressive strength of concrete at 28 days of age by examining the influences of several factors, such as temperature, water-to-binder ratio (w/b), GGBFS-to-binder ratio (GGBFS/b), fine aggregate, coarse aggregate, and superplasticizer. A statistical modeling approach was employed to comprehensively analyze these parameters and assess their impact on the compressive strength. To accomplish this, the study collected and analyzed data from the literature, resulting in a dataset of 210 observations. The dataset was divided into training and testing groups, and statistical analyses were performed to assess the relationships between the input parameters and compressive strength. The correlation analysis revealed insignificant relationships between the input parameters and compressive strength, indicating that multiple factors affect the strength. Different models, such as linear regression, nonlinear regression, quadratic, full quadratic models, and artificial neural networks (ANN) were employed to predict the compressive strength. The findings of this study contribute to a better understanding of the factors that influence the compressive strength of concrete containing GGBFS. The results underscore the importance of considering multiple parameters to predict strength accurately.

This paper analyzed the main diseases of the friction high-strength bolt (FHSB) joints in order to study the characteristics of the corrosion products of the joints in steel bridge and the influence factors. Seven representative FHSB connection pairs and eight steel plate samples were selected from the Dongying Shengli Yellow River Bridge, which has been in operation for 33 years. Then Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD) were used to analyze the microscopic morphology and chemical composition of the corroded surface of the samples. Finally, this paper discussed the relationship between the corroded sample surface and the environmental corrosion. The research results showed that construction quality problems, such as non-standard hole expansion, segmental slab joint dislocation and contact surface pollution, accelerated corrosion of the contact surface. With the increase of corrosion degree of joints, the contact surface of aluminum spraying layer gradually changed from a rugged and dense state to a smooth and porous powder state. With the corrosion of the steel plate substrate, the contact surface gradually changed from a fluffy stratified state to a surface bonding state. It was inferred that the friction coefficient of the FHSB connection node on the corroded aluminum sprayed contact surface first decreased and then increased. The corroded node samples detected not only a large number of S and Cl elements, but also the oxides of Mn, Si and other elements as well as FeS. It was speculated that node corrosion was also related to atmospheric (acid rain) and industrial dust and other corrosive environments. Almost all samples detected the component SiO2 of the Yellow River soil, as well as Mg, Ca, K, Na and other elements at the same time, which is basically consistent with the component elements of the Yellow River soil. Therefore, it was inferred that it was related to the inclusion of the Yellow River soil.

Abstract: During firing from a mortar, an important issue is the parameters of compressibility of the ground on which the mortar is placed. This affects the operation of the mortar (including safety). During the qualification tests of the mortar, the influence of different types of substrate on its strength and work during shooting should be examined. Until now in the Polish standardization documents was no clear description about the substrate parameters used for this kind of tests. Analysis of the literature also did not allow to determine the dependence of the mortars displacement in the function of the type of substrate and its geotechnical parameters. Therefore, the authors carried out analytical and experimental analysis of the use of geotechnical methods to determine the parameters of the substrate for mortar testing. The paper presents the proposed types of standardized soil and their research methods. Preliminary tests were also carried out using the prescribed measurement methods and a comparative mortar firing test. Subsequently, an analysis of the results was carried out and the possibilities of using the proposed methods of measuring the parameters of soil compressibility were determined.

Objectives: In order to solve the problem that most of the existing research focuses on the binary tactile attributes of objects,which ignores the tactile attribute strength and category recognition,an attribute strength and category recognition method based on convolutional neural network matrix-label is proposed. Methods:Firstly,in the data preparation stage,we preprocess the raw data and determine the matrix labels to build the haptic dataset.Secondly,in the feature extraction stage,we fuse the haptic data of two fingers and use the convolutional neural network to extract the attribute strength features.Finally,in the attribute strength and category recognition stage,all channel haptic data is fused to predict the attribute strength and category.Results:We compared with the multi-label convolutional neural network method in terms of elastic strength,hardness strength and category,and compared the attribute strength recognition capabilities of the two methods using novel objects outside the haptic dataset.The results show that the accuracy of the last 20 iterations of the matrix-label method has an average elastic strength of 96.73%,hardness strength of 97.34%,and category of 96.67%.The performance is better.When the Euclidean distance between the prediction of the novel object and the real label is less than 1,the accuracy of the elastic strength is best to reach 100%,and the hardness strength is best to reach 100%.The performance is better. Conclusions:The effectiveness of the method has been verified.Comparing with the convolutional neural network method,our method can effectively recognize the attribute strength and category of objects.

The use of whole-body vibration (WBV) for therapeutic purposes is far from being standardized and only very recently an empirical foundation for reporting guidelines for human WBV studies has been published. Controversies about safety and therapeutic dosage stll exist. The present study aimed to investigate the metabolic and mechanical effects of low-intensity WBV in according to the ISO 2631 norm on subjects with obesity. 41 obese subjects (BMI≥ 35 kg/mˆ2) were recruited to participate in a 3-week multidisciplinary inpatient rehabilitation program including fitness training and WBV training. During WBV the posture was monitored with an optoelectronic system with 6 infrared cameras (Vicon, Vicon Motion System, Oxford, UK). The primary endpoints were: variation in body composition, factors of the metabolic syndrome, functional activity (sit-to-stand and 6-min walking test), muscle strength, and quality of life. Secondary endpoints were: modification of irisin, testosterone, growth hormone, IGF1 levels. We observed significant changes in salivary irisin levels, Group 2 (p&lt;0.01) as compared to the control group, while muscle strength, function, and other metabolic and hormonal factors did not change after a 3-week low-intensity WBV training respect control group. Future studies are needed to deeper investigate the potential metabolic effect of low-intensity WBV in managing weight.

The development of high complexity geometry parts is one of the main goals of the additive manufacturing technology. However, the failure of printed structures and the joining of different parts to create complex assemblies represents a real challenge in the research of efficient and sustainability techniques for the permanent assembly of polymers. Laser welding processes have been used as a single step method to join metals until years ago. Nowadays, the growing trend in the use of thermoplastics for additive manufacturing has led to the need to adapt this technique to materials with a very specific nature and more sensitive to thermal effects. Also, the possibility of transmitting the laser beam through transparent polymer layers allows to focus the energy supply on internal sections of the assembled components. In this research, an infrared laser marking system was used to join two different samples of polylactic acid manufactured by fused deposited modeling technology. In order to increase the effectiveness of the bonding process, a transparent and a dark sample have been used as assembly material, focusing the laser beam on the interface area of the two parts. By means of tensile tests, dimensional measurement and the use of optical microscopy techniques, a basis was established that links the supplied energy by laser to the joining performance.

Abstract: This paper is focusing on the stabilisation of soil using jute fibre as soil stabilizer. Stabilisation is the process of modifying the properties of a soil to improve its engineering performance and used it for a variety of engineering works. This study examines the potential of soil stabilization with jute fibre when it is cut into roughly 30mm lengths as stabilizer. The varying percentages like 0.5%, 1%, 1.5 and 2% of pieces of jute fibre were used and mixed it with soil. The laboratory tests such as California Bearing Ratio (CBR) test, modified compaction tests and direct shear strength tests have been conducted to observe the change in engineering properties of soil. On the basis of the experiments performed, it can be concluded that the stabilization of soil using 30mm pieces of jute as stabilizer improves the strength characteristics of the soil so that it becomes usable as one of the reinforcing material for the construction of roadways, parking areas, site development projects, airports and many other situations where sub-soils are not suitable for construction.

Although sarcopenia is characterized by a loss of muscle strength and skeletal muscle mass, few studies have evaluated the effect of muscle strength on hepatocellular carcinoma (HCC) patients. We separately evaluated the impact of sarcopenia-related factors (grip strength [GS] and the skeletal muscle index [SMI]) on the survival among lenvatinib-treated unresectable HCC (u-HCC) patients. This single-center cohort study was conducted at a university hospital. The study population included 63 lenvatinib-treated u-HCC patients managed between April 2018 and April 2020. A decreased GS and decreased SMI were found in 21 (33.3%) and 22 (34.9%) patients, respectively. The overall survival (OS) of the normal GS group was significantly higher than that of the decreased GS group, while that of the normal and decreased SMI groups did not differ markedly. There were no significant differences in the progression-free survival between the normal GS and decreased GS groups or the normal SMI and decreased SMI groups. A multivariate Cox proportional hazards model showed that ALBI2b (hazard ratio [HR] 4.39) and a decreased GS (HR 3.55) were independently associated with an increased risk of poor prognosis. In addition to the hepatic functional reserve, a decreased GS was a poor prognostic factor in lenvatinib-treated u-HCC patients.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

Corrosion is considered as one of the main factors in the structural performance deterioration of steel members. In this study, experimental and numerical methods were used to assess the reduction in compressive strength of short tubular steel columns with local corrosion damage. The corrosion damage was varied with different depths (0, 1.5, 2, 3, 4, 4.5, and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160, and 180 mm), circumference (0, 90, 180, 270, and 360°), and location along the column. A parametric numerical study was performed to establish a correlation between the residual compressive strength and the severity of corrosion damage. The results showed that as the corrosion depth, height and circumference increased, the compressive strength decreased linearly. As for the corrosion height, the residual compressive strength became constant after decreasing linearly when the corrosion height was greater than the half-wavelength of buckling of the short columns. An equation is presented to evaluate the residual compressive strength of short columns with local corrosion wherein the volume of the corrosion damage was used as a reduction factor in calculating the compressive strength. The percentage error using the presented equation was found to be within 11.4%.

Understanding the stability limit of crystalline materials under variable tensile stress conditions is of capital interest for their technological applications. In this study, we present results from first-principles density functional theory calculations that quantitatively account for the response of selected covalent and layered materials to general stress conditions. In particular, we have evaluated the ideal strength along the main crystallographic directions of 3C and 2H polytypes of SiC, hexagonal ABA stacking of graphite and 2H-MoS2. Transverse superimposed stress on the tensile stress was taken into account in order to evaluate how the critical strength is affected by these multi-load conditions. In general, increasing transverse stress from negative to positive values leads to the expected decreasing of the critical strength. Few exceptions found in the compressive stress region correlate with the trends in the density of bonds along the directions with the unexpected behavior. In addition, we propose a modified spinodal equation of state able to accurately describe the calculated stress-strain curves. This analytical function is of general use and can also be applied to experimental data anticipating critical strengths and strains values and providing informattion on the energy stored in tensile stress processes.

Two X chromosomes of female mammals randomly inactivate one of paternal or maternal X chromosome in early embryonic development and all the daughter cells produced from these cells retain the same feature of X chromosome inactivation, which is called X chromosome inactivation (XCI). Studying the mechanisms of XCI is important for understanding epigenetic that plays an important role in age-associated diseases. The previous studies have demonstrated that binding of RNAs and DNAs may play a role in activating gene expression. In this paper, our study aims to explore whether the mechanisms of XCI involve the RNA binding strength to X chromosome DNAs. The bioinformatics analyses based on big data were used to analyze the simulated binding strength of RNAs (RNA binding strength) to 23 chromosomes (including X chromosome and 22 human autosomes) and the characteristics of repetitive sequences in the X-inactivation centre. The results revealed that RNA binding strength of the long arm of the X chromosome that is almost entirely inactivated in XCI was significantly lower than that of all autosomes and the short arm of X chromosome, meanwhile the RNA binding strengths of inactivation regions in X chromosome were significantly lower than that of regions escaping from XCI. Different repetitive sequence clusters within the center of XCI presented a cross distribution characteristic. To further prove whether the repetitive sequences in human X chromosome involve in XCI, we cloned long interspersed element (LINE-1, L1) and short interspersed element (Alu) from human Xq13, the center of XCI, and constructed expression vectors carrying sense-antisense combination repetitive sequences (L1s or Alus). Effects of combined L1 or combined Alu sequences on expression of EGFP reporter gene were examined in stably transfected HeLa cells, which simulates the effects of repetitive sequences located on chromosomes. The results of experiments revealed transcribed L1 repetitive sequences activated EGFP reporter gene expression, so did the Alus. The experiment results suggested repetitive sequences activated genes by interaction of transcribed RNAs and DNAs. Since the binding of RNAs and DNAs can activate gene, so the low RNA binding strength of human X chromosome may be one of reasons of XCI. The cross distribution characteristics of different repetitive sequence clusters leading to a cascade of gene activation or gene inactivation may be the reason of transcriptional silencing one of the X chromosomes in female mammals.

The thorough description of the peculiarities of additively manufactured structures represents a current challenge for aspiring freeform fabrication methods, such as the selective laser melting (SLM). All of which have an immense advantage in the fast fabrication (no special tooling or moulds required), the geometrical flexibility in the design of components, and their efficiency when only low quantities are required. However, designs demand the precise knowledge of the material properties, which in case of additively manufactured structures are anisotropic and, under certain circumstances, in addition of an inhomogeneous nature. Furthermore, these characteristics are highly dependent on the fabrication settings. Within this study, the anisotropic tensile properties of selective laser melted stainless steel (1.4404, 316L) are investigated: The Young’s modulus ranged from 148 GPa to 227 GPa, the ultimate tensile strength from 512 MPa to 699 MPa and the breaking elongation ranged, respectively, from 12% to 43%. The results were compared to related studies, in order to classify the influence of the fabrication settings. Furthermore, the influence of the chosen raw material was addressed by comparing deviations on the directional dependencies reasoned by differing microstructural developments during manufacture. Stainless steel was found to possess its maximum strength at a 45° layer versus loading offset, which is precisely where AlSi10Mg was previously reported to be at its weakest.

Today, the style of light construction materials used in building is one of the most important factors in reducing building's dead load and better performance of the structures in the earthquake. One of the ways to reduce the structure weight is to use lightweight blocks instead of using traditional materials. The main purpose of this research is to compare density, compressive strength and water absorption volume of non-load-bearing lightweight blocks made of natural and artificial lightweight aggregates. Scoria lightweight aggregates of Sanandaj, Ghorveh mine, pumice in Tabriz, Bostanabad mine, and Leca in Leca enterprise have been used to make the samples. Given the importance of the materials used, grading of coarse-grained materials has been conducted based on the standard of 7657 and grading of fine materials have been conducted based on the standard of 302.The experiments' results show that Scoria blocks due to hard texture, and high mechanical resistance of their lightweight aggregates, have had higher compressive strength, and density and lower water absorption volume compared to pumice and Lika lightweight aggregate blocks. Pumice blocks despite having desirable compressive strength and lower density compared to the two other blocks have higher water absorption volume, and do not meet the standard conditions. This same factor causes it faces with less interest. Among these Lika blocks with density of 1151.94 (kg per cubic meter) below 2000 kilograms per cubic meter of Iran density standard of 7782 (28-day compressive strength of 2.57 MPa), higher than 2.5 MPa of Iran compressive strength standard of 7782 (and water absorption volume of 282.92 kg per cubic meter) below 288 kilograms per cubic meter of Iran water absorption volume standard of 7782 (as a non-load-bearing lightweight block) have been diagnosed desirable.

A composite is a material formed from the combination of two or more constituent materials through a non-homogeneous mixture. This research aims to determine the effect of volume fraction and fiber orientation angle of the hybrid polyester-ulin wood powder (Eusideroxylon zwageri)-wire mesh composite on bending strength. The bending test was conducted using ASTM D-790 standard with a three-point bending test method. The composite was made using the hand lay-up method with various compositions of particles and polyester. The results showed that the composition with less ulin wood powder and finer mesh size with a 45° wire mesh angle orientation had the highest bending strength and high deformation capability. The addition of wire mesh did not significantly increase the bending strength but could reduce the effect of decreased deformation capability.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

Hamstring injuries present a notable challenge to the performance and durability of soccer athletes, particularly those situated in rural areas where access to specialized training facilities may be scarce. This literature review delves into the amalgamation of resistance and flexibility training as a holistic strategy for averting hamstring injuries among rural-based soccer athletes. Utilizing existing scholarly works, this review underscores the significance of resistance training in enhancing hamstring strength, power, and stamina, while flexibility training augments muscle pliability and range of motion, thus diminishing the likelihood of injuries. Furthermore, it scrutinizes a range of resistance and flexibility routines customized to meet the specific requirements of soccer and the limitations of rural settings. Through the amalgamation of evidence-based methodologies, this review puts forth the mechanisms of injury and pragmatic suggestions for coaches, trainers, and athletes to implement efficient injury prevention protocols. Highlighting the collaborative advantages of resistance and flexibility training, this methodology strives to enhance performance and shield against hamstring injuries in rural-based soccer athletes.

The bentonite slurry trenches are becoming increasingly popular in the excavation process of trenches, especially for diaphragm wall construction. The problem that needs to be addressed is the stability of bentonite slurry trenches. This paper presents a stability analysis of trenches with temporary support of bentonite slurry, with unit weights ranging from 10.5 to 12.0 kN/m3, in the realistic stratum: C3 in the Hue city area. The analysis employs the shear strength reduction technique (SSR) with Mohr-Coulomb materials for the numerical method to evaluate the factor of safety (FS). The finite element method (FEM) software program (RS) and the finite difference method (FDM) FLAC software were applied. Additionally, the limit equilibrium method (LEM) of Bell-Washbourne and three-dimensional (3D) Bishop are used for calculating trench stability. The analysis results show a good agreement between RS2 and FLAC2D and RS3 and FLAC3D. Secondly, upon comparison, it is noted that the safety factors of the 3D software programs (RS3, FLAC3D) are higher than those of the 2D software programs (RS2, FLAC2D), ranging from 52.3 to 63.0% for trench lengths of 6m. However, for trench lengths of 54m, the safety factor values in 2D and 3D are nearly equal. Thirdly, the safety factor of the Bell-Washbourne method (LEM) is lower than the numerical analysis methods (FLAC and RS programs). Using the three-dimensional numerical method appears to be effective for estimating stability.

Coal bottom ash (CBA) is a byproduct of coal-burning power plants. This material can be used as a fine aggregate replacement in concrete to reduce global natural material depletion. Concrete usage is increasing rapidly; subsequently, the industry’s carbon footprint is increasing. Using CBA in the construction industry will reduce the technical and economic problems associated with power plants by reducing solid waste. This project aimed to determine if adding new sustainable materials, such as CBA, to concrete will reduce natural raw material usage, energy consumption, and greenhouse gas emissions while improving performance. This study included two projects: comparing increased CBA content to the two-control project and determining the optimum content based on the compressive strength. The optimum CBA content is 50%, which reduces fine aggregate usage in a concrete mix by 50% while maintaining equivalent or better concrete strength than a pure Portland concrete mix without CBA. The air content of the concrete mix containing % CBA decreased with increased CBA content and compressive strength, possibly due to the spacing factor of the voids in the mix and CBA’s porous and fineness behavior. The CBA optimum content had a unit weight lower than the controls for both projects, which makes the CBA mix a lightweight concrete. Using this material can significantly reduce natural material usage and environmental harm by reducing CBA waste disposal and improving concrete performance.