Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A three-dimensional, time-dependent, computational fluid dynamics model of a single channel of a F10 SOFC stack in Forschungszentrum Jülich GmbH is developed to investigate chromium poisoning for different stack designs, temperatures and absolute air humidities. The model takes into account both chemical and electrochemical mechanisms of chromium poisoning and is able to predict the spatial distribution of SrCrO4 and Cr2O3. The voltage degradation over 100 kh can be simulated quantitatively. According to the simulation results, chromium poisoning is almost eliminated by the application of the protective coating fabricated by the atmospheric plasma-spraying (APS) technology. Besides, with the help of the APS protective coating, operating a SOFC stack with less dehumidified air at 650 oC is possible according to the simulation.

Here we performed a comparative experimental analysis by EPR spectroscopy of the intensity of nitric oxide (NO) production and copper content in the injured and uninjured areas of the frontal lobes and the hippocampus of the brain of male Wistar rats, after modeling of combined brain and spinal cord injury. Brain and spinal cord injury were modelled by local destruction of the left precentral region of the brain using a stylet followed by hemorrhage injury at the level of the first lumbar vertebra of the spinal cord. We found a significant decrease in NO production 7 days after injury modeling in the injured and uninjured (contralateral) brain regions, but the copper content remained unchanged one week after injury modeling. Thus, combined brain and spinal cord injury is not accompanied by a radical change in the activity of the antioxidant system in the brain, which is also confirmed by the absence of changes in NO production and copper content in the hippocampus.

The master molecular regulators and mechanisms determining longevity and health span include nitric oxide (NO) and superoxide anion radicals (SOR). L-arginine, the NO synthase (NOS) substrate, can restore a healthy ratio between the dangerous SOR and the protective NO radical to promote healthy aging. Antioxidant supplementation orchestrates protection against oxidative stress and damage—L-arginine and antioxidants such as vitamin C increase NO production and bioavailability. Uncoupling of NO generation with the appearance of SOR can be induced by asymmetric dimethylarginine (ADMA). L-arginine can displace ADMA from the site of NO formation if sufficient amounts of the amino acid are available. Antioxidants such as ascorbic acids can scavenge SOR and increase the bioavailability of NO. The topics of this review are the complex interactions of antioxidant agents with L-arginine, which determine NO bioactivity and protection against age-related degeneration.

The master molecular regulators and mechanisms determining longevity and health span include nitric oxide (NO) and superoxide anion radicals (SOR). L-arginine, the NO synthase (NOS) substrate, can restore a healthy ratio between the dangerous SOR and the protective NO radical to promote healthy aging. Antioxidant supplementation orchestrates protection against oxidative stress and damage—L-arginine and antioxidants such as vitamin C increase NO production and bioavailability. Uncoupling of NO generation with the appearance of SOR can be induced by asymmetric dimethylarginine (ADMA). L-arginine can displace ADMA from the site of NO formation if sufficient amounts of the amino acid are available. Antioxidants such as ascorbic acids can scavenge SOR and increase the bioavailability of NO. The topics of this review are the complex interactions of antioxidant agents with L-arginine, which determine NO bioactivity and protection against age-related degeneration.

Individual susceptibility to pulmonary oxygen toxicity (PO2tox) is highly variable and currently lacks a reliable biomarker for predicting pulmonary hyperoxic stress. As nitric oxide (NO) is involved in many respiratory system processes and functions, we aimed to determine if expired nitric oxide (FENO) levels can provide an indication of PO2tox susceptibility in humans. Eight U.S. Navy trained divers volunteered as subjects. The hyperoxic exposures consisted of six- and eight-hour hyperbaric chamber dives conducted on consecutive days in which subjects breathed 100% oxygen at 202.65 kPa. Subjects’ individual variability in pulmonary function and FENO was measured twice daily over five days and compared with their post-dive values to assess susceptibility to PO2tox. Only subjects who showed no decrements in pulmonary function following the six-hour exposure conducted the eight-hour dive. FENO decreased by 55% immediately following the six-hour oxygen exposure (n=8, p<0.0001) and by 63% following the eight-hour exposure (n=4, p<0.0001). Four subjects showed significant decreases in pulmonary function immediately following the six-hour exposure. These subjects had the lowest baseline FENO and the lowest post-dive FENO and had clinical symptoms of PO2tox. Individuals with low FENO were the first to develop PO2tox symptoms and deficits in pulmonary function from the hyperoxic exposures. These data suggest that endogenous levels of NO in the lung may protect against the development of PO2tox.

Hypertension and arterial stiffness are the main factors contributing to cardiovascular disease. L-citrulline, a nitric oxide precursor, has been proposed as a blood pressure-lowering intervention. This study aimed to investigate the impact of L-citrulline on central and peripheral blood pressure, arterial stiffness, and muscle oxygenation at rest and during an isometric knee extension exercise protocol. Twelve older males received 6 g of L-citrulline or a placebo for six days using a double-blind crossover design. Blood hemodynamics parameters (i.e., arterial and brachial systolic and diastolic blood pressure, mean arterial pressure, pulse pressure, heart rate), arterial stiffness (i.e., augmented pressure, augmentation index, forward, backward wave pressure and carotid-femoral pulse wave velocity) and muscle oxygenation [i.e., oxyhemoglobin (Δ[O2Hb]) and deoxyhemoglobin (Δ[HHb]), total hemoglobin concentration (Δ[tHb]) and tissue saturation index (TSI%)], were measured at baseline, post-supplementation and during isometric exercise. No significant effects of L-citrulline supplementation were observed at rest or during exercise on blood pressure, arterial stiffness, and muscle blood flow. Both central and peripheral blood pressure were increased during the exercise, which is consistent with isometric contractions. The results of the present study question the efficacy of short-term L-citrulline in decreasing blood pressure at rest or attenuating blood pressure increases during isometric exercise.

Recent advances in synthetic membranes allow their use in fields as diverse as food and agriculture, biotechnology, industrial wastewater treatment, and potable water production. Among the newly developed technologies, nanofiltration for liquids and more particularly for desalination of seawater or saline aquifers are actively pursued. However, current solid-state membranes performance is limited, which calls for the development of novel formulations for membranes offering both high permeability (ion and water flux) and ion differentiation (selectivity), usually considered antagonist features. We report the development of hybrid nanoporous membranes made of solid-state polymeric carbonate track-etched (PCTE) thin films in which biological ion channels such as Gramicidin A (GA), alpha-hemolysin (α-HL), and outer-membrane protein F (OmpF) aquaporin are confined and graphene oxide (GO) conjugated cobalt ion selective binding peptide motifs (Copep) are adsorbed, referring as bioinspired and biomimetic approaches, respectively. These solid-state nanoporous membranes are attracting widespread attention since they offer scalability, mechanical robustness, selectivity, controlled pore dimension and shape, for water sustainability. The ion permeability, ion diffusion coefficient and selective ion recognition are evaluated via nanofiltration, cell diffusion kinetics, and UV-Visible absorption spectroscopy to gain insights into the role of key performance parameters including effective ion confinement in track-etched pores, rich surface chemistry, and peptide-induced channel for selective ion transport. These findings provide new avenues for artificial ion channels by synergistic combination of eco-friendly material design such as GO enabled by bio-molecular recognition chemistry.

Luminescent properties of epitaxial Cu2O thin films were studied in 10-300 K temperature range and compared with luminescent properties of Cu2O single crystals. Cu2O thin films were deposited epitaxially by the electrodeposition method on either Cu or Ag substrates at different processing parameters, which determined the epitaxial orientation relationships and encapsulated surface. Cu2O (100) and (111) single crystal samples were cut from a crystal rod grown by the floating zone method. Luminescence spectra of thin films contain the same emission bands as single crystals around 720, 810 and 910 nm, characterizing VO2+, VO+ and VCu defects, correspondingly. Additional emission bands, whose origin is under discussion, are observed around 650-680 nm, while the exciton features are negligibly small. The relative mutual contribution of the emission bands varies depending on the particular thin film sample. Existence of the domains of crystallites with different orientation determines the polarization of luminescence. PL of both Cu2O thin films and single crystals is characterized with negative thermal quenching in the low temperature region, the reason of this phenomenon is discussed.

As a derivative of graphene, graphene oxide (GO) was initially developed by chemists to emulate some of the key properties of graphene, but it was soon recognized as a unique material in its own right, addressing an application space that is not accessible to chemical vapor deposition based materials. Over the past decade, GO has emerged as a new frontier material with tremendous advances in its material fabrication and quality control over its properties. These in turn have led to rapid progress in GO based photonics, electronics, and optoelectronics concepts and devices, evoking new science and paving the way for many technological breakthroughs with exceptional performance. Here, we review the unique fundamental characteristics of GO, its thin film fabrication methods, patterning techniques, and mechanisms for tuning its material properties. This latter capability in particular has enabled novel advanced functional photonic, electronic, and optoelectronic devices. Understanding these insights is essential for designing and tailoring GO properties for state-of-the-art applications including solar energy harvesting, energy storage, medical diagnosis, image displays, and optical communications. We conclude by discussing the open challenges and exciting opportunities of this field, together with future prospects for major technological advancements and breakthroughs.

The present work demonstrates the optimization of the ligand structure in the series of bis-phosphine oxide and carbamoylphosphine oxide representatives for efficient coordination of Tb3+ and Eu3+ ions with the formation of the complexes exhibiting high Tb3+- and Eu3+-centered luminescence. The analysis of the stoichiometry and structure of the lanthanide complexes obtained by XRD method reveals the great impact of the bridging group nature between two phosphine oxide moieties on the coordination mode of the ligands with Tb3+ and Eu3+ ions. The bridging imido-group facilitates the deprotonation of imido-bisphosphine oxide ligand followed by the formation of tris-complexes. The spectral and PXRD analysis of the separated colloids indicates that the high stability of the tris-complexes provides their safe conversion into polystyrenesulfonate-stabilized colloids under the solvent exchange method. The red Eu3+-centered luminescence of the tris-complex exhibits the same specificity in the solutions and the colloids. The pronounced luminescent response on the antibiotics ceftriaxone allows to sense the latter in aqueous solutions with the LOD value equal to 0.974 M.

When present in specific amounts in the air, the colorless, odorless, and tasteless gases monoxide and carbon dioxide may either replace oxygen in red blood cells (CO) or increase the respiratory rate causing cardiac arrhythmias (CO2), leading to death. Commercial sensors take around 8 h to detect levels of CO (50 PPM), causing moderate poisoning. SnO2 presents controlled interactions with the atmosphere using conductance and vacancy adjustments to capture electrical properties. However, the selectivity of gas detection by SnO2 can still be improved, thus also increasing the application possibilities. The present study aimed to optimize the sensing of CO and CO2 in SnO2 using palladium functionalization. The vapor-liquid-solid method synthesized a network of SnO2 nanobelts decorated with palladium nanoparticles. The sensitivity of the sensors for CO and CO2 were evaluated, characterizing parameters such as response time, a wide range of CO and CO2 concentrations, and temperature. In the seventh measurement cycle, the sensor response for different concentrations of gases in consecutive cycles showed a sensitivity of up to 125% for CO in 60 s. Furthermore, we observed increased sensor sensitivity with material doping with nanoparticles from 130 ppm to 1360 ppm in 30 seconds to CO. Conclusion: The results provide a better understanding of the sensitivity of SnO2 in palladium-decorated nanoparticles, offering insights for detecting low CO concentrations quickly. The behavior of these doped nanosensors showed us the importance of considering them as a practical possibility for detecting these gases of importance to human health.

This study describes an eco-friendly synthesis of ZnO nanoparticles using aqueous oat extract. The advanced electrochemical and optical features of green synthesized ZnONPs displayed excellent antibacterial activity, and exhibited an important role in pharmaceutical determinations. The formation of nanoscale ZnO was confirmed using various spectroscopic and microscopic investigations. The formed nanoparticles were found to be around 100 nm. The as-prepared ZnONPs were monitored for their antibacterial potential against different bacterial strains. The inhibition zones for ZnONPs were found as E. coli (16 mm), P. aeruginosa (17 mm), S. aureus (12 mm) and B. subtilis (11 mm) using 30 µg mL-1 sample concentration. Also, ZnONPs exhibited significant antioxidant effects 58 to 67 % with an average IC50 value of 0.88 ± 0.03 scavenging activity and 53 to 71 % (IC50 value 0.73 ± 0.05) against the DPPH and ABTS scavenging free radicals, respectively. The photocatalytic potential of ZnONPs for Rhodamine B dye degradation dye under UV irradiation was performed. The photodegradation process was carried out as a function of time-dependent and the complete degradation (nearly 98 %) with color removal after 120 min. Conclusively, the synthesized ZnONPs using oat biomass might provide a great promise in the future for biomedical applications.

Immunoglobulin G (IgG), a type of antibody, represents approximately 75% of serum antibodies in humans, and is the most common type of antibody found in blood circulation Consequently, the development of simple, fast and reliable systems for IgG detection are of considerable interest which can be achieved using electrochemical sandwich-type immunosensors. In this study we have developed an immunosensor sub-strate using an inexpensive and very simple fabrication method based on ZnO nanorods obtained through the electrodeposition of ZnO. The ZnO nanorods were treated by electrodepositing a layer of reduced gra-phene oxide to ensure an easy immobilization of the antibodies. On this substrate, the sandwich configura-tion of the immunosensor was built through different incubation steps, that were all optimized. The im-munosensor is electrochemically active thanks to the presence of gold nanoparticles tagging the secondary antibody, therefore it has been used to measure the current density of the hydrogen development reaction which is indirectly linked to the concentration of H-IgG antigens. In this way the calibration curve was constructed obtaining a linear range of 1-100 ng / ml with a detection limit of few ng / mL and good sensi-tivity.

Poly-ether-ether ketone (PEEK) is a great potential thermoplastic in industry and medical treatment and health. In this work, the PEEK/GO and PEEK/MoS2 composites were prepared by a novel hot isostatic pressing method. The addition of GO alters the tribological behaviours mechanism, fatigue wear mechanism is predominant to PEEK/GO composites. However, the combination of abrasive and adhesive wear mechanisms is observed for PEEK/MoS2 composites and PEEK. The reason is the hardness and tensile strength of composites are increased with the appropriate addition of GO. The response time to stable friction state of PEEK/GO and PEEK/MoS2 composites reduces in compared with PEEK, which conduce to shorten running-in time, reduce energy consumption and improve the tribological performances of composites. The addition of GO and MoS2 can effectively decrease the friction coefficient and wear rate, and the optimal content of GO and MoS2 was 0.7 wt.% and 15 wt.%, respectively. The results indicate that PEEK/GO and PEEK/MoS2 are impressive composites that possess super tribological properties.

Being a chilling-sensitive staple crop, rice (Oryza sativa L.) is vulnerable to climate change. The competence of rice to withstand chilling stress should, therefore, be enhanced through technological tools. The present study employed chemical intervention like application of sodium nitroprusside (SNP) as nitric oxide (NO) donor and elucidated the underlying molecular mechanisms of NO-mediated chilling tolerance in rice. At germination stage, germination indicators were interrupted by chilling stress (5.0 ± 1.0°C for 8 h day‒1), while pretreatment with 100 μM SNP markedly improved the indicators. At seedling stage (14-day-old), chilling stress caused stunted growth with visible toxicity along with alteration of biochemical markers, for example, increase in oxidative stress markers (superoxide, hydrogen peroxide, and malondialdehyde) and osmolytes (total soluble sugar; proline and soluble protein content, SPC), and decrease in chlorophyll (Chl), relative water content (RWC), and antioxidants. However, NO application attenuated toxicity symptoms with improving growth performance which might be attributed to enhanced activities of antioxidants, mineral contents, Chl, RWC and SPC. Furthermore, principal component analysis indicated that water imbalance and increased oxidative damage were the main contributors to chilling injury, whereas NO-mediated mineral homeostasis and antioxidant defense were the critical determinants for chilling tolerance in rice. Collectively, our findings revealed that NO protects against chilling stress through valorizing cellular defense mechanisms, suggesting that exogenous application of NO could be a potential tool to evolve cold tolerance as well as climate resilience in rice.

Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.

White spot lesions (WSLs), a side effect of orthodontic treatment, can result in reversible and unaesthetic results. Graphene oxide (GO) with a bioactive glass (BAG) mixture(BAG@GO) was added to Low Viscosity Transbond XT(LV) in a ratio of 1, 3, 5%. The composite’s characterization and its physical and biological properties were verified with scanning electron microscopy(SEM) and X-ray diffraction(XRD); its microhardness, shear bond stress (SBS), cell viability, and adhesive remnant index (ARI) were also assessed. Efficiency in reducing WSL was evaluated using antibacterial activity of S. mutans. Anti-demineralization was analyzed using a cycle of the acid-base solution. Adhesives with 3 or 5 wt.% of BAG@GO showed significant increase in microhardness compared with LV. The sample and LV groups showed no significant differences in SBS or ARI. The cell viability test confirmed that none of the sample groups showed higher toxicity compared to the LV group. Antibacterial activity was higher in the 48-hour group than in the 24-hour group; the 48-hour test showed that BAG@GO had a high antibacterial effect, which was more pronounced in 5 wt.% of BAG@GO. Anti-demineralization effect was higher in the BAG@GO-group than in the LV-group; the higher the BAG@GO concentration, the higher the anti-demineralization effect.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

A cuprous oxide (Cu₂O) thin layer served as the base for a non-enzymatic glucose sensor in an alkaline medium, 0.1 NaOH solution, with a linear range of 50-200 mg/dL using differential pulse voltammetry (DPV) measurement. An X-ray photoelectron spectroscopy (XPS) study confirmed the formation of the cuprous oxide layer on the thin gold film sensor prototype. Quantitative detection of glucose in both phosphate-buffered saline (PBS) and undiluted human serum were carried out. Neither ascorbic acid nor uric acid even at a relatively high concentration level of 100mg/dL in serum interfered with the glucose detection, demonstrating the excellent selectivity of this non-enzymatic cuprous oxide thin layer based glucose sensor. Chronoamperometry (CA) and single potential amperometric voltammetry were used to verify the measurements obtained by differential pulse voltammetry (DPV), and the positive results validated that the detection of glucose in a 0.1 M NaOH alkaline medium by DPV measurement was effective. Nickel, platinum and copper are commonly used metals for non-enzymatic glucose detection. The performance of these metal-based sensors for glucose detection using DPV were also evaluated. Cuprous oxide (Cu₂O) thin layer based sensor showed the best sensitivity for glucose detection among the sensors evaluated.

Sentinel lymph node dissection (sLND) using a magnetometer and superparamagnetic iron oxide nanoparticles (SPIONs) as a tracer was successfully applied in prostate cancer (PCa). Radioisotope-guided sLND combined with extended pelvic LND (ePLND) achieved better node removal, increasing the number of affected nodes or the detection of sentinel lymph nodes outside the established ePLND template. We determined the diagnostic value of additional magnetometer-guided sLND after intraprostatic SPION-injection in high-risk PCa. This retrospective study included 104 high-risk PCa patients (PSA >20 ng/ml and/or Gleason score ≥8 and/or cT2c) from a prospective cohort who underwent radical prostatectomy with magnetometer-guided sLND and ePLND. The diagnostic accuracy of sLND was assessed using ePLND as a reference standard. Lymph node metastases were found in 61 of 104 patients (58.7%). sLND had a 100% diagnostic rate, 96.6% sensitivity, 95.6% specificity, 96.6% positive predictive value, 95.6% negative predictive value, 3.4% false negative rate, and 4.4% false positive rate (detecting lymph node metastases outside the ePLND template). These findings demonstrate the high sensitivity and additional diagnostic value of magnetometer-guided sLND, exceeding that of ePLND through the individualized extension of PLND or the detection of sentinel lymph nodes / lymph node metastases outside the established node template in high-risk PCa.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

The dynamic equilibrium of iron homeostasis has an important role in sustaining metabolic and neurological functions during human life. Iron excretion is modest and unregulated hence this overall equilibrium is tightly regulated in normal conditions by increasing deficient or limiting excessive iron assimilation. Here we focus on neural tissue overload, dyshomeostasis that is preceded by excessive assimilation, disturbances in internal homeostasis or both. Normal steps in iron homeostasis include its uptake across the apical membrane of the enterocytes in a mildly acidic duodenal milieu by the major importer of ferrous iron, Divalent Metal Transporter 1 (DMT1) (Nramp2/DCT1/SLC11A2, solute carrier family 11 member 2) [1, 2], responsible for the uptake of Non-Transferrin Bound Iron (NTBI) and divalent metals [3], passage through enterocytes bound to a chaperone and crossing the basal membrane via the only known cellular ferrous iron exporter, ferroportin [4] with the iron bound to transferrin (Tf) as it exits. Cells in peripheral tissues largely utilize circulating iron after uptake by receptor-mediated endocytosis of Tf-bound Iron [5]. Derangement of duodenal NTBI absorption of iron and heavy metals is influenced by systemic iron metabolism associated with inflammation that leads to iron accumulation into peripheral tissues and potential development of neurodegenerative diseases, involving distribution and fine regulation of DMT1 also in the central nervous system, where inflammatory-related acidosis influences DMT1 uptake, via its action as a proton cotransporter. Pharmacological strategies to inhibit NTBI transport selectively will be illustrated in relationship to protection, particularly neuroprotection, against iron overload associated with acidosis, inflammation, neuroinflammation and subsequent neurodegeneration.

In the ongoing transition from fossil fuels to renewable energies, advances are particularly expected regarding safe and cost-effective solutions. Publicising instances of such advances and emphasising safety considerations constitute the rationale for this communication. Knowing that high-strength steels can prove economically relevant for transporting hydrogen in pipelines by limiting the pipe wall thickness required to withstand high pressure, one advance relates to a bench designed for contributing to study the safety of the gaseous transport or renewable-energy-related buffer storage of hydrogen. That bench has been specifically implemented at technology readiness level TRL 6 for testing initially intact, damaged, or pre-notched DN 300/NPS 12, DN 600/NPS 24, and DN 900/NPS 36 pipe sections in order to provide data allowing for the possible validation of fully satisfactory predictive models in terms of hydrogen embrittlement and potential corollary ruin. The other advance relates to the reactivation of a previously fruitful applied research into mass solid-state hydrogen storage through a new public-private partnership. This latest development comes at a time when markets have started driving the hydrogen economy, bearing in mind that phase-change materials decisively allow levelling the heat transfers during the absorption/melting and solidification/desorption cycles and attaining an overall energy efficiency of up to 80% for MgH₂-based compacts doped with expanded natural graphite.

Currently, the textile industry is among the most rapidly expanding areas of the economy and is an important source of water pollution. There are many efficient chemical and physical methods for treating textile effluent, but they produce secondary pollutants. Therefore, there is a need to manage the textile waste wastewater. The potential EPS-producing and plant growth-promoting rhizobacteria Lysinibacillus capsici PB300 (T) bacteria strain has been isolated from the bark borer-affected Peltophorum pterocarpum plant and has been determined to be effective in > 95 decolorizing Reactive Red 120, and other azo dyes such as AB11385%, orange II 94.62%, Congo red 94.62%, phenol red 94.54%, and mixtures of azo dyes 81.66%. Physico-chemical factors were optimized manually, including Taguchi design. EPS production, PGPR strain, and fabric discoloration of L. capsici were qualitatively studied. The FTIR, GC-MS, and UV absorbance studies also confirmed that the dye had been broken into its amines. Research findings using enzyme assays have shown that the bacteria Lysinibacillus capsici PB300 (T) can utilize laccase and manganese peroxidase and are capable of degrading dyes significantly. According to this work, immobilised L. capsici cells and the studied four bacterial consortiums, Lysinibacillus capsici PB300 (T), Alcaligenes faecalis subsp. Phenolicus DSM 16503 (T), Acinetobacterbaumanni ATCC 19606 (T), and Pseudomonasaeruginosa JCM 5962 may be employed to degrade RR120 effectively, and it is concluded that L. capsici PB300 (T) bacteria is significantly efficient in textile effluent treatment.

Supramolecular structures with specific applications are a pillar in several areas of science. Thus, from a contemporary point of view, there are several reasons to feel inclined to cover a systematic, or historic critique of the supramolecular concept itself. First, the idea of a supramolecular material seems more secure now than it was decades ago. Second, updating the interacting of MOFs and supramolecular chemical and conversely, supramolecularity to assemble MOFs and to make ef-ficient complex systems in multiple cutting-edge applications. Third, we should here simply confine to a consideration of how workers in this field have tried to correlate the notion of the idea of supramolecular systems linking self-assembly considerations. Thereby, this is clearly an ad-vantage that optimized geometries obtained on the conductive bases described that undoubtedly, some of these systems have substantial applications and create a significant practical interest. The outline of this review encompasses a general introduction to MOFs and supramolecularity, the key unit of the study presented here, followed by a survey of recent advances in supramolecular chemistry in confined space, relationships of MOFs with the supramolecular chemistry, electro-chemical synthesis of MOFs, and switchable MOFs. Finally, some discussion on possible future perspectives of this field is given.

Bicyclic peptides have attracted the interest of pharmaceutical companies because of their remarkable properties putting them on a new path in medicine. Their conformational rigidity that improves proteolytic stability, leads to rapid penetration into tissues via any possible route of administration and elimination, occurring by renal metabolism, is of great importance for people with a history of liver diseases. In addition, each ring can function independently, making them extremely versatile molecules for further optimization. In this paper we compared the potentiometric and spectroscopic properties studied by UV-Vis, MCD, and EPR, of four synthetic analogues of the bi-cyclic peptide c(PKKHP-c(CFWKTC)-PKKH). In particular we correlated the structural and spectral properties of complexes with coordinating abilities toward Cu(II) ions of MCL (Ac-PKKHPc(CFWKTC)PKKH-NH2) that contains the unbinding cycle and N- and C-terminal linear parts, with two histidine residues, one per part; two monocyclic ligands containing one histidine residue, both in the N-terminal position i.e., MCL2 (Ac-PKKHPc(CFWKTC)PKKS-NH2) and in the C-terminal position i.e., MCL3 (Ac-PKKSPc(CFWKTC)PKKH-NH2), respectively, and the linear structure LNL (Ac-PKKHPSFWKTSPKKH-NH2).

Biopolymers are of growing interest, but to improve some of their poor properties and performance, it is required the formulation of bio-based blends and/or adding of nanoparticles. For this purpose, in this work, two different metal oxides, such as zinc oxide (ZnO) and titanium dioxide (TiO2), at different concentrations (0.5, 1 and 2 %wt.) have been added in polylactic acid (PLA) and polylactic acid/polyamide 11 (PLA/PA11) blends to establish their effects on solid-state properties, morphology, melt behaviour, and photo-oxidation resistance. It seems that the addition of ZnO in PLA leads to a significant reduction of its rigidity probably due to an inefficient dispersion in the melt state, while the addition of TiO2 does not penalise PLA rigidity. Interestingly, the addition of both ZnO and TiO2 in PLA/PA11 blend has a positive effect on the rigidity because of blend morphology refinement and leads to a slight increase in film hydrophobicity. The photo-oxidation resistance of neat PLA and PLA/PA11 blend is significantly reduced due to the presence of both metal oxides, and this must be considered when designing the potential applications. The last results suggest that both metal oxides could be considered as photo-sensitive degradant agents for biopolymer and biopolymer blends.

Present research focus on the effect of different processing routes on physical and mechanical properties of nano Ti(CN) based cermet’s with metallic binders. Tungsten carbide (WC) is added as secondary carbide and Ni-Co are added as metallic binders in nano Ti(CN) based cermet processed via Conventional and Spark Plasma Sintering (SPS). Systematic comparison of composition and sintering conditions for different cermet’s’ systems is done to design the novel composition and sintering conditions. Nano TiCN powder was prepared by 30hr of ball milling. Highest density of >98.5% percent was achieved for SPS processed cermet’s sintered at 1200°C and 1250°C for 3 min. at 60 MPa pressure in comparison to conventionally sintered cermet’s at 1400°C for 1hr with two stage compaction process, uniaxially at 150 MPa and isostatically at 300 MPa pressure respectively. Comparison of XRD analysis of milled powders of different time intervals was done to understand the characteristics of the as received and milled powders. Peak broadening was observed after 5 hr. of ball milling, and it increased till 30hr. Also, peak broadening and refined carbide size was observed in XRD and SEM micrograph of SPS processed cermet. TEM analysis of milled powder showed internal structure having regular periodic arrangement of planes. SEM (BSE) images of all cermets primarily showed three major microstructural phases of core-rim-binder with black, grey and white contrast respectively. In the present sintering conditions high hardness of ~16 GPa and fracture toughness of ~9 MPa m1/2 was obtained for SPS processed cermets sintered at higher temperature.

Biofilm serves as the residence for bacteria, wherein bacteria attach to surfaces and produce extracellular polymeric substances, including proteins, polysaccharides, and extracellular DNA. In recent years, biofilm reactors have gained increasing significance, playing a crucial role, for instance, in immobilizing heavy metals from waterways. This paper employs a bibliographic study to analyze the most important keywords and organizations in the field of biofilm reactors, identifying recent significant papers. Additionally, the paper discusses the opportunities for the future development of biofilm reactors. Through this study, a better understanding of key factors in biofilm reactor research is achieved, providing valuable guidance for future studies and applications in this field.

Metal halide perovskites have shown excellent optoelectronic properties, including high photoluminescence quantum yield, tunable emission wavelength, narrow full-width at half-maximum and low-cost solution-processed fabrication, which make it exhibit great potential as the emission layer materials of light emitting diodes. With the joint efforts of researchers from different disciplines, there has been a significant progress in the improvement of external quantum efficiency (EQE) and stability of perovskite light emitting diodes (PeLEDs) in recent few years, especially in green PeLEDs with EQE over 30%. In this review, we firstly introduce the basic device structure of PeLEDs, as well as the factors influencing EQE and stability of PeLEDs. Secondly, the development of lead-based and lead-free PeLEDs are summarized systematically. Thirdly, challenges of PeLEDs are discussed in detail, including low EQE of blue PeLEDs, poor device stability and EQE roll-off. Finally, some suggestions and perspectives of the future research directions for PeLEDs are proposed.

The CMT (Cold Metal Transfer) arc welding process is a convenient instrument for the assembly of thin sheets [1], [2]. More particularly, it permits the decrease of the amount of heat transferred to the parts to-be assembled, thus reducing their subsequent deformations. The present work aims at simulating the CMT welding of thin stainless-steel sheets in order to develop an approach that allows the prediction of temperature fields, as well as final deformations induced by the welding process. For that purpose, instrumented tests and numerical simulations were set aiming at comparing the experiments with simulations. Butt-welding of stainless-steel sheets was considered, with a thickness ranging from 1 to 1.2 mm. The weld seam samples were observed in order to set an equivalent heat source for each configuration. Moreover, the electric current and voltage were surveyed, and temperature measurements were performed using K-type thermocouples. In addition, displacement measurements were obtained using the DIC (Digital Image Correlation) technique. Thermomechanical simulations were then carried out using an equivalent heat source approach, considering the phase changes of elements, i.e. the transitions from solid to liquid and from liquid to solid. These simulations also consider the actual geometry of seams induced by addition of a filler material.

The results of a study of the processes of formation of macro- and micro-inhomogeneity of ingots and rolled sheets are presented. To study the nature and sources of surface defects in rolled sheets, a comparative method of structural-concentration analysis of metal at the end-to-end metallurgical process of ingot - slab - sheet metal has been developed, based on the metallographic method of studying the structure and qualitative analysis of non-metallic inclusions. The research results showed that the quality of the surface of rolled sheets is determined mainly by the physical heterogeneity of the crust zone of the ingots, and the internal defects of thin rolled sheets largely depend on the contamination of the metal with non-metallic inclusions and off-axis segregation. A mechanism for transforming defects in the casting cortical zone into surface and internal defects in rolled sheets is proposed.

The increading emission of carbon dioxide to the atmosphere has urged the scientific community to investigate alternatives to alleviate such emissions being the principal contributor to the greenhouse gas effect. One major alternative is carbon capture and utilisation (CCU) towards the production of value-added chemicals using diverse technologies. This work aims at the study of the catalytic potential of different cobalt-derived nanoparticels for methanol syntheis from carbon dioxide hydrogenation. Thanks to its abundance and cost-efficacy, cobalt can serve as an economical catalyst compared to noble-metal-based catalysts. In this work, we present a systematic comparison among different cobalt and cobalt oxide nanocomposites in terms of their efficiency as catalysts for carbon dioxide hydrogenation to methanol as well as how different supports can enhance their catalytic capacity. The oxygen vacancies in the cerium oxide act as carbon dioxide adsorption and activation sites, which facilitates a higher methanol production yield.

(1) Background: The synthesis of core-shell magnetic mesoporous nanoparticles (MMSN) from phase transfer process is usually performed at 100-250 mg scale. At the gram scale, nanoparticles without core or with multicore systems are observed. (2) Methods: Iron oxide core nanoparticles (IO) were synthesized through thermal decomposition procedure of -FeO in oleic acid. Phase transfer from chloroform to water was then performed in order to wrap IO with mesoporous silica shell through the sol-gel procedure. MMSN were then functionalized with DTPA, and used for the separation of metal ions. Their toxicity was evaluated (3) Results: The phase transfer pro-cedure was crucial to obtained MMSN at large scale. Three synthesis parameters were rigorously controlled: temperature, time and glassware. Homogeneous dispersion of MMSN at the gram scale was successfully obtained. After functionalization with DTPA, the MMSN-DTPA were shown to have a strong affinity for Ni ions. Furthermore toxicity was evaluated in cells, zebrafish and through seahorse metabolic assays, and the nanoparticles were found nontoxic. (4) Conclusions: We developed a method of preparation of MMSN at the gram scale. After function-alization with DTPA, the nanoparticles were efficient in metal ion removal and separation, fur-thermore, no toxicity was noticed up to 125 µg.mL-1 in zebrafish.

It is important to develop new antibacterial drugs since the emergence of bacterial resistance to available antibiotics. Metal nanoparticles have the potential to combat antibiotic resistance and are effective antibacterial agents. Here, we demonstrate the biogenic production of zinc nanoparticles using Rhododendron arboreum stem bark. The biosynthesized ZnNPs were characterized through different analytical techniques such as UV-vis, FTIR, EDX, SEM, and XRD. Clinical isolates such as E. coli, S. aureus, and K. pneumonia were used to check the antibacterial efficacy of the biosynthesized zinc nanoparticles. The MIC and MBC values against K. pneumonia, S. aureu, and E. coli were found to be 34±0.21 and 11.71±0.47, 47±0.11 and 23.86±0.84 and 94±0.18 and 40.43±0.16 µg/mL, respectively. It dramatically decreased the integrity of the cell membrane and markedly increased the permeability of both inner and outer membranes. The green synthesized ZnNPs have good catalytic activity. It degraded 65% of methyl orange dye within 6h when the mixture was kept in direct sunlight, thus demonstrating good photodegradation potential and can be employed as a good photocatalyst. According to these results, biosynthesized zinc nanoparticles could be a potential therapy option for controlling bacterial pathogenesis and an effective photocatalyst for the elimination of hazardous water contaminants.

Metal-organic framework (MOF) is a porous hybrid material of metal ions connected by organic bridging ligands. The coordination bonds link the metal ions, metal-ion clusters, and organic ligands to create the MOFs, and the materials are a distinctive class of crystalline frameworks. These porous materials possess relatively large surface area, tunable pore sizes, various functionalities, and high thermal stability. Therefore, diverse area of research including electrochemical sensor development utilizes distinctive and engineered MOFs materials. The review critically analyzes the strategy adopted for synthesizing a variety of MOFs materials. The role of these engineered materials in the fabrication of a miniaturized device demonstrates the detection of various emerging water contaminants in an aqueous medium. The studies demonstrated an understanding of the insights of sensor and device development. Moreover, the challenges encountered utilizing the MOFs in the electrochemical sensor development are precisely included, along with future perspectives of these studies.

Ionic gel electrolyte retains the characteristics of non-volatilization, non-flammability and outstanding electrochemical stability of ionic liquid, and shows good electrochemical performance combined with the excellent characteristics of different matrix materials, which is considered to be the best choice to achieve the high energy density and safety at the same time. In this paper, a flexible and self-healing ionic gel electrolyte is prepared by solvent-assisted method based on a zteric ion (ZI) copolymer. Abundant hydrogen bonds and synergistic interaction of ions in the electrolyte system endowed it with wonderful self-healing ability. The ionic conductivity of 9.06×10-4 S cm-1 at room temperature was achieved. Besides, the tLi+ was also increased to 0.312. The self-healing function of the ionic gel electrolyte ensured the long-term tolerance of the SHIGE. The capacity retention rate of the Li//LiFePO4 battery is 96% after 155 cycles at 0.1 C at 60 oC. This polymer electrolyte is expected to solve the problem of increasing polarization，which is caused by the low lithium ions migration number in ionic liquid electrolyte. And ultimately, it gives rise to a good rate performance.

In response to the growing demand for high-strength and high-toughness materials in industries like aerospace and automobiles, there is a need for metal matrix composites (MMCs) that can simultaneously enhance strength and toughness. This paper focuses on the design configurations of MMCs, which include both the configurations resulting from reinforcements and the inherent heterogeneity of the matrix itself. The mechanical properties of MMCs are influenced by factors such as reinforcement content, shape, size, and spatial distribution within the composite architecture. Among them, Aluminum matrix composites (AMCs) are particularly significant in aerospace, electronics, and electric vehicles due to their potential for weight reduction and enhanced performance. However, the challenge lies in the inverse relationship between strength and toughness, hindering the widespread utilization and large-scale development of MMCs. The design configuration of composites plays a critical role in achieving concurrent improvements in strength and toughness. This review explores the advantages of toughness, toughening mechanisms, reinforcement distribution characteristics, and structural parameters in the design of composite architectures. Drawing inspiration from biological composites like bone, the development of synthetic composites with homogeneous structural designs provides insights into attaining exceptional strength and toughness in lightweight engineering structures. Additionally, understanding fracture behavior and toughening mechanisms in heterogeneous nanostructures is vital for advancing the field of metal matrix composites. Summarily, the design of composite architectures holds tremendous potential for tailoring AMCs with outstanding strength and toughness, addressing the requirements of lightweight engineering structures in various industries.

Evidence of the efficacy and safety of colorectal stent placement for palliation remains insufficient. This single-arm, prospective, multicenter study with WallFlex enteral colonic stent included 200 consecutive patients with malignant large bowl obstruction in the palliation cohort. The technical and clinical success, as well as stent patency and complications as short-term (≤ 7 days) and long-term (&gt; 7days) outcomes, of high axial force self-expandable metal stent (SEMS) placement was evaluated. The technical and clinical success rates were 98.5% and 94.5%, respectively. Non recurrent colorectal obstruction at 1 year was 63.9%, and 71.2% of the patients remained free of recurrent colorectal obstruction until death or the last follow-up. Fifty-six patients (28.0 %) received chemotherapy and five patients were administered bevacizumab after stent placement. The overall complication rate was 47%, including four (2.0%) early-onset and ten (5.0%) late-onset perforations, mostly due to stent-edge injury. Only the use of a long SEMS was a risk factor for perforation. In conclusion, endoscopic colorectal stenting using high axial force SEMS is an effective and safe procedure for palliation in patients with malignant colorectal obstruction. However, care should be taken to avoid perforation at the stent edge when using a long SEMS.

The spike protein (S) of SARS-CoV-2 has been shown to bind to the human angiotensin-converting enzyme 2 (ACE2) receptor with much higher affinity compared to other coronaviruses. The binding interface between the ACE2 receptor plays a critical role in the entry mechanism of SARS-CoV-2 virus. There are specific amino acids involved in the interaction between S protein and ACE2 receptor. This specificity is critical for the virus to establish a systemic infection and cause COVID-19 disease. In the ACE2 receptor, the largest number of amino acids that play a crucial role in the mechanism of interaction and recognition with the S protein are located in the C-terminal part which represents the main binding region between ACE2 and S. This fragment is abundant in coordination residues such as aspartates, glutamates and histidine that could be targeted by metal ions. Zn²⁺ ion binds to the ACE2 receptor in its catalytic site and modulates its activity, but it could also contribute to the structural stability of the entire protein. The ability of the human ACE2 receptor to coordinate metal ions, such Zn²⁺, in the same region where it binds to the S protein could have a crucial impact in the mechanism of recognition and interaction of ACE2-S with consequences on their binding affinity that deserve to be investigated. To test this possibility, this study aims to characterize the coordination ability of Zn²⁺, and also Cu²⁺ for comparison, with selected peptide models of the ACE2 binding interface using spectroscopic and potentiometric techniques.

Endoscopic ultrasound-guided gallbladder drainage (EUS-GBD) is an alternative to surgery for acute cholecystitis (AC) in poor operative candidates. However, the role of EUS-GBD in non-cholecystitis (NC) indications has not been well studied. We compared clinical outcomes of EUS-GBD for AC and NC indications. Consecutive patients undergoing EUS-GBD for all indications at a single center were retrospectively analyzed. Fifty-one patients underwent EUS-GBD during the study period. Thirty-nine (76%) patients had AC while 12 (24%) had NC indications. NC indications included malignant biliary obstruction (n = 8), symptomatic cholelithiasis (n = 1), gallstone pancreatitis (n = 1), choledocholithiasis (n = 1), and Mirizzi’s syndrome (n = 1). Technical success was noted in 92% (36/39) for AC and 92% (11/12) for NC (p &gt; 0.99). Clinical success rate was 94% and 100%, respectively (p &gt; 0.99). There were 4 adverse events in the AC group and 3 in the NC group (p = 0.62). Procedure duration (median 43 vs 45 minutes, p = 0.37), post-procedure length of stay (median 3 vs 3 days, p = 0.97), and total gallbladder related procedures (median 2 vs 2, p = 0.59) were similar. EUS-GBD for NC indications is similarly safe and effective as EUS-GBD in AC.

Two solvated rhenium(IV) complexes with formula [ReCl4(bpym)]·MeCN (1) and [ReCl4(bpym)]·CH3COOH·H2O (2) [bpym = 2,2'-bipyrimidine] have been prepared and characterized by means of Fourier transform infrared spectroscopy (FT–IR), scanning electron microscopy and energy dispersive X-ray analysis (SEM–EDX), single-crystal X-ray diffraction (XRD) and SQUID magnetometer. 1 and 2 crystallize in the monoclinic system with space groups P21/n and P21/c, respectively. In both compounds, the Re(IV) ion is six-coordinate and bound to four chloride ions and two nitrogen atoms of a 2,2’-bipyrimidine molecule forming a distorted octahedral geometry around the metal ion. In the crystal packing of 1 and 2, intermolecular halogen⋯halogen and π⋯halogen type interactions are present. Hydrogen bonds take place only in the crystal structure of 2. Both compounds exhibit an akin crystal framework based on halogen bonds. Variable-temperature dc magnetic susceptibility measurements performed on microcrystalline samples of 1 and 2 show a similar magnetic behavior for both compounds, with antiferromagnetic exchange between the Re(IV) ions connected mainly through intermolecular Re-Cl···Cl-Re interactions.

We have detected a large Nernst effect in the CDW state of the multiband organic metal α−(BEDT−TT)2KHg(SCN)4. We find that there exists a significant gradient of charge relaxation processes that can generate a sizeable contribution adding especially to the transverse thermoelectric signal. Apart from the phonon drag, the energy relaxation processes governing the electron-phonon interactions and the momentum relaxation processes governing the charge mobility of the q1D group of carriers have a significant role in observing the large Nernst signal in the CDW state. The emphasised momentum relaxation dynamics in the low field CDW state is a clear indicator of a significant carrier mobility that can lead to the largest Nernst signal in this state. The momentum relaxation is reduced with increasing angle and magnetic field, i.e., in the high field CDW state which is reflected in the smaller Nernst effect amplitude. In this case only the phonon drag and electron-phonon interactions are contributing to the transverse thermoelectric signal. Our findings advance and change the previous observations on the complex properties of this organic metal.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

All living organisms require some metal ions for their energy production as well as metabolic and biosynthetic processes. Within cells, metal ions are involved in the formation of adducts interact with metabolites and macromolecules (proteins and nucleic acids). The proteins that require binding to one or more metal ions to be able to carry out their physiological function are called metalloproteins. About one third of all protein structures in the Protein Data Bank involve metalloproteins. Over the past few years there has been a tremendous progress in the number of computational tools and techniques making use of 3D structural information to support the investigation of metalloproteins. This trend has been boosted also by the successful applications of neural networks and deep learning approaches in molecular and structural biology at large. In this review, we discuss recent advances in the development and availability of resources dealing with metalloproteins from a structure-based perspective. We start by addressing tools for the prediction of metal-binding sites (MBSs) using structural information on apo-proteins. Then, we provide an overview of methods for and lessons learned from the structural comparison of MBSs in a fold-independent manner. We then move to describing databases of metalloprotein/MBS structures. Finally, we summarize recent DL applications enhancing the functional interpretation of metalloprotein structures.

We report a prebiotically relevant solution to the N1-ribosylation of pyrimidine nucleobases, a well-known challenge in the RNA World hypothesis. It is found that the presence of metal cations and clay mineral enables the previously unachievable direct ribosylation of uracil, providing by far the highest yield. Spectroscopy and chromatography analyses confirmed the formation of ribosylated uracil. The method can also be extended to the ribosylation of 2-pyrimidinone. These findings are also compatible with the metal-doped-clay model developed by our lab for the unified route of the selection of ribose and subsequent syntheses of nucleotide and RNA.

The present study utilizes a metal inert gas welding (MIG) to make a dissimilar weld joint of different stainless steel grades AISI 304, 314, 316L, 420 and a standard structural steel S355MC to estimate the correlation of a microstructure and the mechanical properties. The microstructure of the base metals (BM), the heat affected zone (HAZ), the fusion zone (FZ) and the weld seam were analyzed using optical microscopy. Optical microscopy did not reveal any presence of weld defects such as porosity or cracks. The analysis of microstructure showed that both the austenitic and martensitic stainless steel weld structures contain some retained delta ferrite and coarse Me23C6 carbides in the HAZ, while the FZ exhibits delta ferrite and some retained austenite. The hardness profiles revealed difference between austenitic and martensitic steel welds that the later showed extremely high values in the HAZ (~500 HV/0.1) which causes fracture in this zone. The welds of all austenitic steel grades withstood tensile test, showing the average tensile strength of 472 MPa with fracture observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds, and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.

The screening and treatment of acid mine drainage (AMD) using Na₂FeO₄ has been explored. Elemental composition was performed using an ICP-OES for the raw and treated AMD. The AMD samples were collected from three different sampling sites (RTW1, RTW2 and RTW3) in Pretoria, South Africa with acidic pH ranging between 2.50 and 3.13. Total dissolved solids and Electrical Conductivity of AMD samples ranged between 960 and > 1000 mg. L^-1, 226 and 263 µS. cm^-1, respectively. The final pH of treated water samples increased up to ≥ 9.5 after treatment with Na₂FeO₄. Sodium ferrate showed dual functions by removing metals and raising the pH of the treated water. Concentrations of most trace elements were not complying with WHO and DWAF guideline standards in raw AMD while after treatment with Na₂FeO₄ the concentrations were below guidelines for domestic and irrigation purposes.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

Alzheimer’s disease (AD) is one of the most prevailing neurodegenerative diseases, characterized by memory dysfunction and the presence of hyperphosphorylated tau and amyloid β (Aβ) aggregate in multiple brain regions, including the hippocampus and cortex. The exact etiology of AD has not yet been confirmed. However, epidemiological reports suggest that populations who were exposed to environmental hazards are more likely to develop AD than those who were not. Arsenic (As) is a naturally occurring environmental risk factor abundant in the Earth’s crust and human exposure to As predominantly occurs through drinking water. Convincing evidence suggests that As causes neurotoxicity and impairs memory and cognition although the hypothesis and molecular mechanism of As-associated pathobiology in AD are not clear yet. However, exposure to As and its metabolites leads to various pathogenic events such as oxidative stress, inflammation, mitochondrial dysfunctions, ER stress, apoptosis, impaired protein homeostasis, and abnormal calcium signaling. Evidence has indicated that As exposure induces alterations that coincide with most of the biochemical, pathological, and clinical developments of AD. Here, we overview existing literature to gain insights into the plausible mechanisms that underlie As-induced neurotoxicity and the subsequent neurological deficits in AD. Prospective strategies for the prevention and management of arsenic exposure and neurotoxicity have also been discussed.

Aiming the characterization of road dusts on the surrounding villages of an active mine and to assess metal(loids) bioaccessible fractions, a dust samples survey was undertaken. To achieve these objectives, pseudototal element concentration, mineralogical composition, Enrichment factor and in vitro extraction UBM assay for both gastric (G) and gastrointestinal (GI) phases, were determined. Results obtained revealed that arsenic represents the higher risk to humans, with mean pseudototal values higher than the maximum reference value range. Enrichment factor points to As significant to very high enrichment in all villages. Particles enriched in As, Ca, Fe, Cu, Al, Ti were identified by SEM-EDS in weathered agglomerates, linked to mine wastes and long-distance transport, both by wind and/or traffic. Arsenic bioaccessibility fraction (%BAF) presents low values in the studied samples, possibly due to low Fe complexes solubility with adsorbed As, limiting arsenic release and reducing its bioaccessibility. Concentrations of Cd bioaccessible G and GI phases are within the reference values range, while for Cu are above and for Pb are lower, than reference value range. Results show that the pseudototal fraction risk is overestimated when comparing to BAF (bioaccessible fraction), nevertheless, total G and GI risk are above the carcinogenic target risk (1.00E-06) in most samples. Carcinogenic risk of the bioaccessible contaminants shows that As is the element that represents higher risk for developing cancer over a lifetime, being ingestion the main risk route.

: Dacarbazine, DAC, 5-(3,3-dimethyltriazeno)imidazol-4-carboxamideis is an imidazole-carboxamide derivative, that is structurally related to purines. DAC belongs to the triazene compounds, which are a group of alkylating agents with antitumour and mutagenic properties. DAC is a non-cell cycle specific drug, active on all phases of cellular cycle. In the frame of this work the 3d-metal complexes (cobalt and copper) with dacarbazine were synthesized. Their spectroscopic properties by the use of FT-IR, FT-Raman and 1HNMR were studied. The structures of dacarbazine and its complexes with copper(II) and cobalt(II) were calculated using DFT methods. The effect of metals on the electronic charge distribution of dacarbazine was discussed on the basis of calculated NBO atomic charges. The reactivity of metal complexes in relation to ligand alone was estimated on the basis of calculated energy of HOMO and LUMO orbitals. The aromaticity of imidazole ring in dacarbazine and the complexes was compared (on the basis of calculated geometric indices of aromaticity). Thermal stability of the investigated 3d-metal complexes with dacarbazine and the products of their thermal decomposition were analyzed.

The paramagnetic gadolinium(III) ion is used as contrast agent in magnetic resonance (MR) imaging to improve the lesion detection and characterization. It generates a signal by changing the relaxivity of protons from associated water molecules and creates a clearer physical distinction between the molecule and the surrounding tissues. New gadolinium-based contrast agents displaying larger relaxivity values and specifically targeted might provide higher resolution and better functional images. We have synthesized the gadolinium(III) complex of formula [Gd(thy)2(H2O)6](ClO4)3·2H2O (1) [thy = 5-methyl-1H-pyrimidine-2,4-dione or thymine], which is the first reported compound based on gadolinium and thymine nucleobase. 1 has been characterized through vis-IR, SEM-EDAX and single-crystal X-ray diffraction techniques, and its magnetic and relaxometric properties have been investigated by means of SQUID magnetometer and MR imaging phantom studies, respectively. On the basis of its high relaxivity values, this gadolinium(III) complex can be considered a suitable candidate for contrast enhanced magnetic resonance imaging.

Bacteria a Microscopic organisms are the most inexhaustible and flexible of microorganisms and constitute a huge division of the whole living earthly biomass, certain microorganisms were found to amass metallic components at a high limit Was Known as Bacterial Bio-sorption Due to their little size, capacity to become under controlled conditions, and their Accommodation to an extensive variety of ecological situations; Potent metal bio-sorbents among microorganisms, at low pH esteems, cell divider ligands are protonated and contend essentially with metals for official. With expanding pH, more ligands, such as amino and carboxyl groups, could be exposed, leading to attraction between these negative charges and the metals, and consequently increment bio-sorption onto the cell surface. Starting with Isolation and identification of heavy metal-resistant bacteria from rock Ore. Studying Factors Affecting Uranium Bio-sorption, Optimization of bacterial growth conditions and optimum for metal uptake by free and immobilized bacterial cells and Desorption ratio of uranium ions adsorbed by Coli. /alginate, All this evidence suggest that functions groups Represented in our study are responsible for metal uptake in our bacterial biomass beside change in peaks position which assigned for it's groups confirm bio-sorption of metal ions from waste due to ions charge interaction comparing with immobilized we found increase in no of binding sites indicate that immobilized bacterial have high efficiency for metal up take which also change in peaks position which assigned for its groups confirm bio-sorption of metal ions from waste due to ions charge interaction, Where the high bio-sorption yield obtained by bacteria, the Uranium & heavy metal bioremediation process expects microorganisms to be joined to a strong surface.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

Hybrid metal-organic compounds as relatively new and prosperous magnetoelectric multiferroics provide opportunities to improve the polarization, magnetization and magneto-electric coupling at the same time, which usually have some limitations in the common type-I and type-II multiferroics. In this work we investigate the crystal of guanidinium copper(II) formate [C(NH2)3]Cu(HCOO)3 and give novel insights concerning the structure, magnetic, electric and magneto-electric behaviour of this interesting material. Detailed analysis of crystal structure at 100 K is given. Magnetization points to the copper(II)-formate spin-chain phase that becomes ordered below 4.6 K into the canted antiferromagnetic (AFM) state, as a result of super-exchange interaction over different formate bridges. The performed ab-initio colinear density functional theory (DFT) calculation confirm the AFM-like ground state as a first approximation and explain the coupling of spin-chains into the AFM ordered lattice. In versatile measurements of magnetization of a crystal, including transverse component besides the longitudinal one, very large anisotropy is found that might originate from canting of the coordination octahedra around copper(II) in cooperation with the canted AFM order. With cooling down in zero fields the generation of spontaneous polarization is observed step-wise below 270 K and 210 K and the effect of magnetic field on its value is observed also in the paramagnetic phase. Measured polarization is somewhat smaller than the DFT value in the c-direction, possibly due to twin domains present in the crystal. The considerable magneto-electric coupling below the magnetic transition temperature is measured with different orientations of the crystal in magnetic field, giving altogether the new light onto the magneto-electric effect in this material.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

Both types of surgical guides – with and without metal sleeves are founded beneficial in clinical studies. The aim of this in vitro study was to compare time of surgical procedure in dental implantology depending of used type of the surgical guide. Ten three dimensional (3D) printed models of lower jaws were prepared based on complete virtual model of patient clinical conditions with missing teeth 37, 46 and 47. Five of this models were used for implant sites preparation performed with use of surgical guide without metal sleeves and dedicated surgical kit, and next five were used for the same procedure performed with surgical guide with metal sleeves and dedicated surgical kit. Time of implant site preparation were measured and noted. Statistical analysis was performed using Student’s t test for independent samples. Difference of time in both groups were founded as statistically significant (t=-9.94; df =28; p=0.0000). Type of surgical guide is important factor which can impact on time of implant site preparation and all surgical procedure.

Sorghum is a multipurpose crop, but Cr(VI) toxicity influenced the production of the crop and have established highlighted courtesy, due to robust toxicity and a comparatively less known mode of action. Many reports approve the negative impact of Cr(VI) on plants. Yet, it is not clear that, at what concentrations, Cr(VI) inhibits the growth and nutrient quality of Sorghum. In the present research, toxic effects appeared after 1ppm of Cr treatment. The plant growth decreased 15 – 20% and nutritional quality decreased 30 – 40% significantly with increasing concentration of Cr(VI). Toxic components increased 14 – 16% with increasing concentration of Cr(VI) in both the varieties (HJ 541 and SSG 59-3). Chromium was accumulated more in roots followed by shoots with increasing Cr(VI) treatments (0-4 ppm). Chromium at 4ppm level was becoming lethal to Sorghum. Sorghum cultivar SSG 59-3 was more tolerable to Cr toxicity than HJ 541. Chromium accumulated in Sorghum and increased HCN content and at higher doses adversely affects the nutritive values and growth making it toxic for animal consumption. These findings may be useful for scheming a mitigation strategy for chromium toxicity.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

In this paper, a metal cutting machine position control have been designed and simulated using Matlab/Simulink Toolbox successfully. The open loop response of the system analysis shows that the system needs performance improvement. Static output feedback and full state feedback H₂ controllers have been used to increase the performance of the system. Comparison of the metal cutting machine position using static output feedback and full state feedback H₂ controllers have been done to track a set point position using step and sine wave input signals and a promising results have been analyzed.

Highly sensitive multicomponent materials designed for the recognition of hazardous compounds request control over interfacial chemistry. The latter is key parameter in the construction of the sensing (macro)molecular architectures. In this work, multi-walled carbon nanotubes (in short, CNTs) were deposited on diazonium-modified flexible ITO electrodes prior to electropolymerization of pyrrole. This three step process, including diazonium electroreduction, deposition of CNTs and electropolymerization, provided adhesively bonded polypyrrole-wrapped CNT composite coatings on aminophenyl-modified flexible ITO sheets. The aminophenyl (AP) groups were attached to ITO by electroreduction of the in situ generated aminobenzenediazonium compound in aqueous, acidic medium. For the first time, polypyrrole (PPy) was electrodeposited in the presence of both benzenesulfonic acid (dopant) and ethylene glycol-bis(2-aminoethylether)-tetraacetic acid (EGTA) which acts as a chelator. The flexible electrodes were characterized by XPS, Raman and scanning electron microscopy (SEM) which provided strong supporting evidence for the wrapping of CNTs by the electrodeposited PPy. Indeed, the CNT average diameter increased from 182.6 nm to 274.8, 35.65.9 and 17520.1 after 1, 5 and 10 of electropolymerization of pyrrole. The PPy/CNT/NH2-ITO films generated by this strategy exhibit significantly improved stability and higher conductivity compared to a similar PPy coating without any embedded CNTs as assessed by from electrochemical impedance spectroscopy measurements. The potentiometric response was linear in the 10-83×10-7 mol.L-1 Pb(II) concentration range and the detection limit was 2.9×10-9 mol.L-1 at S/N=3. The EGTA was found to drastically improve selectivity for Pb(II) over Cu(II). To account for this improvement, density functional theory (DFT) was employed to calculate the EGTA-metal ion interaction energy which was found to be -374.6 and -116.4 kJ/mol for Pb(II) and Cu(II), respectively, considering solvation effects. This work demonstrates the power of a subtle combination of diazonium coupling agent, CNTs, chelators and conductive polymers to design high-performance electrochemical sensors for environmental applications.

Food preservatives are compound that are used for the treatment of food to improve the shelf life. In the food industry, is necessary to monitor all processes, for both safety and quality of the product. An electronic nose (or e-nose) is a biomimetic olfactory system that could find numerous industrial applications, including food quality control. Commercial electronic noses are based on sensor arrays composed by a combination of different sensors, which include conductometric metal oxide devices. Metal oxide nanowires are considered among the most promising materials for the fabrication of novel sensing devices, which can enhance the overall performances of e-noses in food applications. In the present work, is reported the fabrication of a novel sensor array based on SnO2, CuO and WO₃ nanowires deposited on top of commercial μHPs, provided by ams Sensor Solutions Germany GmbH. The array was tested for the discrimination of four typical compounds added to food products or used for their treatment to increase the shelf life: ethanol, acetone, nitrogen dioxide and ozone. Results are very promising: the sensors array was able to operate for long time consuming less than 50mW for each single sensor, and PCA analysis confirms that the device was able to discriminate between different compounds.

The optimization of the production process of metal mines has been traditionally driven only by economic benefits while ignoring resource efficiency. However, it has become increasingly aware of the importance of resource efficiency since mineral resource reserves continue to decrease while the demand continues to grow. To better utilize the mineral resources for sustainable development, this paper proposes a multi-objective optimization model of the production process of metal mines considering both economic benefits and resource efficiency. Specifically, the goals of the proposed model are to maximize the profit and resource utilization rate. Then, the fast and elitist Non-Dominated Sorting Genetic Algorithm (NSGA-II) is used to optimize the multi-objective optimization model. The proposed model has been applied to the optimization of the production process of a stage in the Huogeqi Copper Mine. The optimization results provide a set of Pareto-optimal solutions that can meet varying needs of decision makers. Moreover, compared with those of the current production indicators, the profit and resource utilization rate of some points in the optimization results can increase respectively by 2.99% and 2.64%. Additionally, the effects of the decision variables (geological cut-off grade, minimum industrial grade and loss ratio) on objective functions (profit and resource utilization rate) were discussed using variance analysis. The sensitivities of the Pareto-optimal solutions to the unit copper concentrate price were studied. The results show that the Pareto-optimal solutions at higher profits (with lower resource utilization rates) are more sensitive to the unit copper concentrate prices than those obtained in regions with lower profits.

Light sources tend to affect images captured in any automatic optical inspection (AOI) system. In this study, the effectiveness of metal-halide lamps, quartz-halogen lamps, and LEDs as the light sources in AOI systems for the detection of the 3rd and 4th layers electrodes of thin-film-transistor liquid crystal displays (TFT-LCDs) is examined experimentally. The results show that the performance of LEDs is generally comparable or better than that of metal-halide and quartz-halogen lamps. The best optical performance is by the blue LED due to its spectrum compatibility with the time-delay-integration charged-coupled device (TDI CCD) sensor and its better spatial resolution. The images revealed by the blue LED are sharper and more distinctive. Since current LEDs are more energy efficient and environmentally friendly, using LEDs as the light source for AOI is very beneficial. As the blue LED performs the best, it should be adopted for AOI using TDI CCD sensors.

The apparent metal-insulator transition (MIT) in two-dimension (2D) was discovered by Kravchenko et al. [1] more than two decades ago in strongly interacting 2D electrons residing in a Si-metal-oxide-semiconductor field-effect transistor (Si-MOSFET). Its origin remains unresolved. Recently, low magnetic field reentrant insulating phases (RIPs), which dwell between the zero-field (B=0) metallic state and the integer quantum Hall (QH) states where the Landau-level filling factor υ > 1, have been observed in strongly correlated 2D GaAs hole systems with large interaction parameter rs (~20-40) and high purity. A new complex phase diagram was proposed, which includes zero field MIT, low magnetic field RIPs, integer QH states, fractional QH states, high field RIPs and insulating phases (HFIPs) with υ < 1 in which the insulating phases are explained by the formation of Wigner crystal. Furthermore, evidences of new intermediate phases were reported. All contribute to the further understandings of the puzzle. This review article serves the purpose of summarizing those recent experimental findings and theoretical endeavors, to foster future research efforts.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

To remove sulfur-containing compounds (SCC) from the diesel fraction 200-360 °C extraction systems have been created based on coordinating organic solvents - dimethylformamide and dimethylsulfoxide and chlorides (CoCl2, CuCl2, CdCl2, MnCl2 and CrCl3) and metal trifluoroacetates (Co (TFA)2, Cu(TFA)2 and Mn(TFA)2). Using PMR spectroscopy the coordination of chloride and metal trifluoroacetate on the oxygen atom in the carbonyl group of DMFA was shown to redistribute electron density in the solvent molecule and to enhance properties of the acceptor center localized on the nitrogen atom. The removal of sulfur-containing compounds from the diesel fraction proceeded under mild conditions - at the temperature of 25 °C and atmospheric pressure. The degree of SCC removal from the diesel fraction in 30 minutes extraction was more than 90%. The interaction of organic solvents with metal salts and sulfur-containing compounds of the diesel fraction was considered within the framework of the concept of "hard and soft acids and bases" (HSAB). The most complete SCC extraction was carried out by "DMFA - Mn(TFA)2, MnCl2 and CrCl3 systems, that was probably connected with the implementation of the" hard base - hard acid "system.

Slow and controlled release systems for drugs, have attracted increasing interest recently. A highly efficient metal-organic gels (MOGs) drug delivery carrier, i.e., MIL-100(Al) gels, has been fabricated by a facile, low cost and environment friendly one-pot process. The unique structure of MIL-100(Al) gels leads to a high loading efficiency (620 mg/g) towards doxorubicin hydrochloride (DOX) as a kind of anticancer drugs. DOX-loaded MOGs exhibited high stability under physiological conditions and sustained release capacity of DOX for up to 3 days (under acidic environments). They further showed sustained drug release behavior and excellent antitumor effects in in vitro experiments on HeLa cells, in contrast with the extremely low biotoxicity of MOGs. Our work provides a promising way for the anticancer therapy, by utilizing this MOGs-based drug delivery system, as an efficient and safe vehicle.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

1) Background: Bipolar or manic-depressive disorder is a malign mental disease that frequently faces social stigma. Educational and thinking models are needed to increase people’s awareness and understanding of the disorder. The arts have potential to achieve this goal. 2) Methods: This paper builds on the recent use of heavy metal music as a thinking and education model. It emphasizes the artistic component of heavy metal and its potential to characterize the symptomatology during the episodes of (hypo)mania and depression and the recurrence of these episodes. Heavy metal music has diversified into subgenres that become allegorical to both the symptoms of episodes and the recurrence of bipolar cycles. 3) Results: Examples of songs are given that mirror distinct facets of the disorder. 4) Conclusion: Although the links drawn between art (music) and science (psychiatry) are inherently subjective, such connections might be used to trigger a learning process, facilitate judgment and decision-making, and induce affective reactions and memory formation in the listener. The approach may facilitate collaborative efforts and serve healthcare professionals and educators as a communication tool to aid the public’s comprehension of the disease and an associated social paradox: On one hand, bipolar disorder incurs substantial costs to society. On the other hand, it benefits from the creative artistic and scientific endeavors of bipolar individuals from which cultural and political gains may ensue.

In this study, we analyzed the microbial community of traditional fermented foods in Jeju Island to identify the distribution of useful microorganisms and confirm their anti-inflammatory and anti-melanogenic effects to determine their potential use as cosmetic ingredients. Firstly, we examined the microbial communities of Omphalius rusticus Jeotgal (OR), Spratelloides gracilis Jeotgal (SG), Chromis notata Jeotgal (CN), Turbo cornutus Jeotgal (TC), Trichiurus lepturus intestine Jeotgal (TL), Branchiostegus japonicus Sweet Rice Punch (BJ), Salted Anchovy Sauce (SA), Jeju Soy Sauce (JSS), and Jeju Soybean Paste (JSP). We found that Latilactobacillus sakei (87.2%), Tetragenococcus halophilus (37.7%), T. halophilus (96.8%), Bacillus subtilis (23.4%), T. halophilus (71.3%), L. sakei (53.7%), Lentibacillus sp. (42.9%), Enterococcus durans (14.6%), and E. durans (32.8%) were the dominant species. Secondly, to study the nine Jeju fermented foods’ anti-inflammatory and anti-melanogenic effects, we employed RAW 264.7 and B16F10 cells, classic cell models for inflammation and melanogenesis studies. Ethyl acetate extracts of the nine Jeju fermented foods all inhibited nitric oxide (NO) and melanin production in a concentration-dependent manner. Thirdly, to test the applicability of the nine Jeju fermented foods to human skin, we used the MTT assay to assess their cytotoxic effects on human keratinocytes (HaCaT cells). Finally, the topical applicability of the nine Jeju fermented foods was tested through primary skin irritation, and it was found that they did not cause any adverse effects. Therefore, extracts from the nine Jeju fermented foods have potential applications as ingredients in anti-inflammatory and anti-melanogenic products and can be used in the cosmetic industry.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

Buckypaper (BP), a flexible and porous material, exhibits photovoltaic properties when exposed to light. In this study, we have employed Radio Frequency (RF) Sputtering of Zinc Oxide (ZnO) followed by rapid thermal annealing to enhance the photovoltaic response of BP. We investigated the impact of various sputtering parameters, such as the gas flow ratio of argon to oxygen and deposition time, on the morphology, composition, resistivity, and photovoltaic characteristics of ZnO-modified BP. Additionally, the photovoltaic performance of the samples under different illumination modes and wavelengths was compared. It was found that optimal sputtering conditions—argon to oxygen flow ratio of 1:2, deposition time of 20 minutes, and power of 100 watts—resulted in a ZnO film thickness of approximately 45 nanometers. After annealing at 400°C for 10 minutes, the ZnO-modified BP demonstrated a significant increase in photocurrent and photovoltage, along with a reduction in resistivity, compared to unmodified BP. Moreover, under gradient illumination, the ZnO-modified BP exhibited a photovoltage enhancement of 14.70 times and a photocurrent increase of 13.86 times, compared to uniform illumination. Under blue light, it showed a higher photovoltaic response than under other colors. The enhancement in photovoltaic response is attributed to the formation of a Schottky junction between ZnO and BP, an increased carrier concentration gradient, and an expanded light absorption spectrum. Our results validate that ZnO sputtering followed by annealing is an effective method for modifying BP for photovoltaic applications such as solar cells and photodetectors.

The formation of a rigid tough interface based on a nacre-like structure in carbon fiber (CF) composites is a promising way to eliminate low delamination resistance. An effective method of coating CFs is electrophoretic deposition (EPD), which, in the case of dissimilar components like graphene oxide (GO) and polymeric glue, usually requires their chemical bonding/ strong interactions. In this work, we focus on chitin nanocrystals (ChNCs), leading to an excellent mechanical performance of artificial nacre, where favorable interactions and bonding with GO were controlled by degrees of deacetylation (5, 15 and 30 %). We have prepared coatings based on GO/ChNCs adducts with 95/5, 90/10,50/50 and 25/75 ratios using optimized EPD conditions (pH, concentration, voltage and time). The prepared materials were characterized using FTIR, TEM, XPS, SEM, DLS, and XRD. SEM evaluation indicates the formation of a homogeneous interlayer, which possesses a fair ability of chemical bonding with the epoxy matrix. Short beam testing of epoxy matrix composites indicates that coating does not decrease stiffness and its relatively low dependence on composition. Therefore, all coatings are promising for a detailed study of delamination resistance using laminate samples. Moreover, facile EPD from water solution/ suspension has a fair potential for industrial applications.

When wastewater containing methylene blue, a cationic dye is improperly treated or immediately dumped into the environment, it can degrade the quality of water bodies and contaminate the ecological environment. The removal of methylene blue from the aqueous solution is critical and urgent. The present work focuses on the use of maize stalk agricultural waste to prepare an adsorbent for the removal of cationic dye (methylene blue) from an aqueous solution. The prepared maize stalk biochar (MSB) was modified with MnO2 and the modified maize stalk biochar was characterized using Fourier transform infrared (FTIR) spectroscopy. Taguchi technique was employed to determine the optimum conditions for the removal of methylene blue (MB) dye from aqueous solution by MMSB. The factors were adsorbent dose (0.5, 1.0 and 1.5 g/100 mL), initial dye concentration (100, 200 and 300 mg/L), contact time (30, 60, 90 minutes) and pH (4, 6 and 8). Among the investigated process factors, adsorption efficiency was influenced by adsorbent dose and initial MB dye concentration. The optimum parameters were 1 g/100 mL adsorbent dose, 100 mg/L initial dye concentration, 60 minutes contact time and a pH of 8.0. This yielded a removal efficiency of 87.49% with adsorption capacity of 206.53 mg/g. The adsorption kinetics agreed with the pseudo-second-order (R2 of 0.999968) model and fitted a Langmuir isotherm (R2 of 0.9795) representing homogeneous monolayer chemisorption.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

: Nanotechnology has expanded what can be achieved in our approach to cancer treatment. The ability to produce and engineer functional nanoparticle formulations to elicit higher incidences of tumor cell radiolysis has resulted in substantial improvements in cancer cell eradication while also permitting multi-modal biomedical functionalities. These radiosensitive nanomaterials utilize material characteristics, such as radio- blocking/absorbing high-Z atomic number elements, to mediate localized effects from therapeutic irradiation. These materials thereby allow for subsequent scattered or emitted radiation to produce direct (e.g., damage to genetic materials) or indirect (e.g., protein oxidation, reactive oxygen species formation) damage to tumor cells. Using nanomaterials that activate under certain physiologic conditions such as the tumor micro-environment can selectively target tumor cells. These characteristics combined with biological interactions that can target the tumor environment allow for localized, radio-sensitization while mitigating damage to healthy cells. This review explores the various nanomaterial formulations utilized in cancer radiosensitivity research. Emphasis on inorganic nanomaterials showcase the specific material characteristics that enable higher incidences of radiation while ensuring localized cancer targeting based on tumor micro-environment activation. The aim of this review is to guide future research in cancer radiosensitization using nanomaterial formulations and to detail common approaches to radiosensization, as well their relations to commonly implemented radiotherapy techniques.

Nitric acid is a key component in the production of nitrate fertilisers and is industrially produced using the Ostwald process. The Ostwald process can be further intensified by oxidising nitric oxide to nitrogen dioxide using heterogeneous catalysts. We have explored various monometallic and bimetallic catalysts for NO to NO2 oxidation and found ruthenium supported on ceria, containing 10 wt.% manganese to be a promising catalyst for oxidising NO to NO2 at low temperatures at industrially relevant conditions. For a feed comprising 10% NO, 6% O2, 15% H2O and rest Ar, and 8% NO, 2% NO2 5% O2, 15% H2O and rest Ar, the ruthenium-manganese catalysts attained NO-NO2 equilibrium below 400∘C. For the 5wt.% ruthenium and 10 wt.% manganese on ceria catalyst, an apparent activation energy of 39.4 kJ/mol and 85.4 kJ/mol were observed in the absence and presence of NO2, respectively. These findings demonstrate the potential of supported bimetallic ruthenium-manganese catalysts for efficient oxidation of NO to NO2 at low temperatures which can lead to significant process intensification of nitric acid plants.

Although 4Ce4YSZ has high corrosion resistance, it faces challenges concerning sinterability and ionic conductivity. Therefore, we studied destabilization behavior caused by corrosion and oxygen vacancy ordering according to ZnO doping. The powders of (4Ce4YSZ)1-x(ZnO)x (x=0.5, 1, 2, 4 mol%) were synthesized through the sol-gel method. With the addition of ZnO, the cubic phase increased, and secondary phases were not observed. The (111) peak showed a higher angle shift in ZnO-doped 4Ce4YSZ compared to 4Ce4YSZ, and TEM-SAED revealed a reduction in the spacing of the (011)t plane, suggesting lattice contraction due to the substitution of the smaller Zn2+ (60 Å) for Zr4+ (84 Å) in the lattice. The local atomic structure analysis was conducted using EXAFS to investigate the oxygen vacancy ordering behavior. Zr K-edge Fourier-transform data revealed a decrease in the Zr-O1 peak intensity with an increasing amount o ZnO doping, indicating an increase in oxygen vacancies. The Zr-O1 peak position shifted to the right, leading to an increase in the Zr-O1 interatomic distance. In the Y K-edge Fourier-transform data, the Y-O1 peak intensity did not decrease, and there was little variation in the Y-O1 interatomic distance. These results suggest that the oxygen vacancies formed due to ZnO doping are located in the neighboring oxygen shell of Zn, rather than in the neighboring oxygen shells of Y and Zr. Impedance measurements were conducted to measure the conductivity, and as the amount of ZnO doping increased, the total conductivity increased, while the activation energy decreased. The increase in oxygen vacancies by ZnO doping contributed to the enhancement of conductivity and it is considered that these created oxygen vacancies did not interact with Zn2+ and did not form defect associations. Fluoride-based molten salts were introduced to the specimens to assess corrosion behavior in a molten salt environment. Yttrium depletion layers (YDLs) were formed on the surfaces of all specimens due to the leaching of yttrium. However, Ce remained relatively stable at the interface according to EDS line scans, suggesting a reduction in the phase transformation (cubic, tetragonal to monoclinic) typically associated with yttrium leaching in YSZ.

Cattle slurry is an important nitrogen source for maize on dairy farms. Slurry injection is an effective measure to reduce ammonia emissions after field application, but with higher risk of nitrous oxide emission than surface application. This study compared soil mineral nitrogen dynamics and nitrous oxide emissions with two ways of application. First, traditional injection at 25 cm spacing between rows followed by ploughing (called “non-placed slurry”), and second, injection using a new so-called goosefoot slurry injector that placed the slurry in ploughed soil as a c. 30 cm broad band at 10 cm depth below maize crop rows with 75 cm spacing (named “placed slurry”). Furthermore, the effect of treating slurry with the nitrification inhibitor 3,4-dimethylpyrazole phosphate (DMPP) in Vizura® was tested with both application methods. The field experiment was conducted on a sandy loam soil in a temperate climate. Both nitrous oxide emissions, and the dynamics of soil mineral nitrogen, were monitored for eight weeks after slurry application and seeding of maize using static chambers. The level of nitrous oxide emissions was higher with non-placed compared to placed slurry, mainly due to higher emissions during the first four weeks. That might be due to higher rates of nitrification rate and in turn stimulation of denitrification process. In both placed and non-placed slurry treatments, Vizura® caused higher soil ammonium concentrations and lower nitrate concentrations, particularly from 3 to 8 weeks after slurry application. The final level of soil nitrate was similar with and without the nitrification inhibitor, but higher with placed compared to non-placed slurry. Adding Vizura® to non-placed slurry reduced nitrous oxide emissions by 70 % when compared to placed slurry. Surprisingly, there was a non-significant trend towards higher cumulative emissions from placed slurry with the nitrification inhibitor compared to untreated slurry, which were due to higher emissions in the last part of the monitoring period (5-7 weeks after slurry application). Possibly degradation of the nitrification inhibitor, and nitrification activity inside the slurry band as the soil dried, promoted nitrous oxide emissions by this time. In summary, placement of untreated slurry in a broad band under maize seeds reduced nitrous oxide emissions compared to non-placed slurry with more soil contact. A comparable reduction was achieved by adding a nitrification inhibitor to non-placed slurry. The pattern of nitrous oxide emissions from placed slurry treated with the inhibitor was complex and requires more investigation.

Wood plastic composite usage and demands have increased due to chemical, and mechanical properties when compared to plastic materials. However, because of the possibility of structural and mechanical changes of the material when exposed to external environment more research needs to be done. In the present study yellow birch/HDPE composites materials made by injection molding were treated by zinc oxide and exposed to fungal rots. Mechanical properties of the composites were assessed by Tensile and Izod impact test. The impact energies of the samples loaded with 30 % ZnO-treated fibers and exposed to G. trabeum and T. versicolor decreased, compared to when samples were not treated with ZnO. The mechanical properties of all samples treated with ZnO and exposed to rot decreased which were reported as a decreased Young's modulus and impact energies. ZnO prevented mycelium proliferation which was nonexistent on samples. It has been noted that the decrease in mechanical properties of treated samples was due to NaOH used to dissolve the ZnO powder.

Pastes containing reduced graphene oxide (rGO) and LiCl-Mn(NO3)2·4H2O are screen-printed on a carbon cloth substrate and then calcined using a nitrogen atmospheric-pressure-plasma jet (APPJ) for conversion into rGO-LiMnOx nanocomposites. The APPJ processing time is within 300 s. RGO-LiMnOx on carbon cloth is used to sandwich H2SO4, LiCl, or Li2SO4 gel electrolytes to form hybrid supercapacitors (HSCs). The areal capacitance, energy density, and cycling stability of the HSCs are evaluated using electrochemical measurement. The Li2SO4 gel electrolyte HSC exhibits the highest areal capacitance and energy density but lower cycling stability. By contrast, the H2SO4 gel electrolyte HSC exhibits better cycling stability but lower areal capacitance and energy density.

Plastics are highly beneficial for the day-to-day activities of human beings; however, their decomposition is limited due to their strong covalent bonding. The concept of degradation of these big molecules into smaller ones or monomers was attempted by several researchers in the preceding decades with limited success. Pyrolysis is one of the ideas used to convert plastics into fuel, rather than small molecules, compared to the crowded structure of polymers. Among these plastics, low-density polyethylene (LDPE) is largely used as carry bags throughout the world, and, herein, the results of catalytic pyrolysis of the conversion of LDPE into fuel are reported. Different dosages of zinc oxide (ZnO) were used as a catalyst to do the pyrolysis at a specific temperature in a batch reactor specially designed at our laboratory. 0.6 g of ZnO was found to be the optimal dosage for a 50 g waste LDPE batch to get the maximum oil yield. The yielded oil was analyzed chemically through Fourier transform infrared spectroscopy (FTIR) and Reformulyzer M4 Hydrocarbon Group Type Analyzer. Evaluation of physical and chemical exergy along with exergetic efficiency of the process was done.

Cancer is considered nowadays one of the main causes of human death worldwide, being characterized by an alteration of the oxidative metabolism. Many natural compounds with anti-tumor attributes have been described, many of them from plant origin. Among them, capsaicin, which is the molecule responsible for the pungency in hot pepper fruits, has been reported to show antioxidant, anti-inflammatory and analgesic activities, as well as anti-proliferative properties against cancer. Thus, in this work the potential anti-proliferative activity of pepper (Capsicum annuum L.) fruits from diverse varieties with different capsaicin content (California < Piquillo < Padrón < Alegría riojana) against several tumor cell lines (lung, melanoma, hepatoma, colon, breast, pancreas, and prostate) has been investigated. The results showed that the capsaicin content in pepper fruits did not correspond with their anti-proliferative activity against tumor cell lines. By contrast, the greatest activity was promoted by the pepper tissues which contained the lowest capsaicin amount. This indicates that other compounds different from capsaicin have this anti-tumor potentiality in pepper fruits. Based on this, green fruits from the variety Alegría riojana, which has negligible capsaicin levels, was used to study the effect on the oxidative and redox metabolism of tumor cell lines from liver (Hep-G2) and pancreas (MIA PaCa-2). Different parameters from both lines treated with pepper fruit crude extracts were determined including, among others, protein nitration and protein S-nitrosation (two post-translational modifications (PTMs) promoted by nitric oxide), the antioxidant capacity, as well as the activity of the antioxidant enzymes superoxide dismutase (SOD), catalase, and glutathione peroxidase (GPX). Besides, the activity of the NADPH-generating enzymes glucose-6-phosphate dehydrogenase (G6PDH), 6-phosphogluconate dehydrogenase (6PGDH), and NADP-isocitrate dehydrogenase (NADP-ICDH) was followed. Our data revealed that the treatment of both cell lines with pepper fruit extracts altered their antioxidant capacity, enhanced the catalase activity, and considerably reduced the activity of the NADPH-generating enzymes. As a consequence, less H2O2 and NADPH seem to be available to cells, thus avoiding cell proliferation and possibly triggering cell death in both cell lines.

NADPH is an indispensable cofactor in a wide range of physiological processes which is generated by a family of NADPH-dehydrogenases, where the NADP-dependent malic enzyme (NADP-ME) is one member of these enzymes. Pepper (Capsicum annuum L.) fruit is a horticultural product worldwide consumed which has great nutritional and economic relevance. Besides the phenotypical changes that undergo pepper fruit during ripening, there are many associated modifications at transcriptomic, proteome ic, biochemical, and metabolic levels. Nitric oxide (NO) is a recognized signal molecule that can exert regulatory functions in diverse plant processes. To our knowledge, there is very scarce information about the number of genes encoding for NADP-ME in pepper plants and their expression during the ripening of sweet pepper fruit. Based on a data-mining approach on the pepper plant genome and fruit transcriptome (RNA-seq), five NADP-ME genes were identified, and four of them, namely CaNADP-ME2 to CaNADP-ME5, were expressed in fruit. The time-course expression analysis of these genes during different fruit ripening stages including green immature (G), breaking point (BP), and red ripe (R) showed that they were differentially modulated. Thus, while CaNADP-ME3 and CaNADP-ME5 were upregulated, CaNADP-ME2 and CaNADP-ME4 were downregulated. Exogenous NO treatment of fruit triggered the downregulation of CaNADP-ME4. Furthermore, the analysis of the cis-regulatory elements showed that CaNADP-ME2 and CaNADP-ME5 were positively regulated by the light-responsive element Box4 whereas CaNADP-ME4 was by ABRE (ACGT-containing abscisic acid response element), which is involved in the abscisic acid (ABA) responsiveness. To get deeper knowledge on this enzyme system from fruits, we obtained the 50-75% ammonium-sulfate-enriched protein fraction containing CaNADP-ME enzyme activity, and this was assayed by non-denaturing polyacrylamide gel electrophoresis (PAGE). The results allowed identifying four isozymes designated CaNADP-ME I to CaNADP-ME IV. Taken together, the data provide new pieces of information on the CaNADP-ME system with the identification of five CaNADP-ME genes and how the four genes expressed in pepper fruits are modulated during ripening and by exogenous NO gas treatment.

Oxidative stress and inflammation are basic pathogenic factors involved in tissue injury, pain, as well as acute and chronic diseases. Since long-term uses of steroids and non-steroidal anti-inflammatory drugs (NSAIDs) cause severe adverse effects, novel effective materials with minimal side effects are required. In this study, polyphenol content and antioxidative activity of rosebud extracts from 24 newly-crossbred Korean roses were analyzed. Among them, Pretty Velvet rosebud extract (PVRE) were found to contain high polyphenols and to show in vitro antioxidative and anti-inflammatory activities. In RAW 264.7 cells stimulated with lipopolysaccharide (LPS), PVRE down-regulated mRNA expression of inducible nitric oxide synthase (iNOS) and cyclooxygenase-2 (COX-2), and thereby decreased nitric oxide (NO) and prostaglandin E2 (PGE2) production. In an air-pouch inflammation model, treatment with PVRE decreased λ-carrageenan-induced tissue exudation, infiltration of inflammatory cells including neutrophils, monocytes and lymphocytes, and tumor necrosis factor-α and interleukin-1β concentrations, as achieved with dexamethasone (a steroid). Notably, PVRE also inhibited PGE2, similar to dexamethasone and indomethacin (an NSAID). The anti-inflammatory effects of PVRE were confirmed by microscopic findings, attenuating tissue erythema, edema, and inflammatory cell infiltration. These results indicate that PVRE exhibits dual (steroid- and NSAID-like) anti-inflammatory activities by blocking both the iNOS ― NO and COX-2 ― PG pathways, and that PVRE could be a promising anti-inflammatory material for diverse issue injuries.

The problem of health status prediction of insulated-gate bipolar transistors (IGBTs) gains a lot of attention in the field of health management of power electronic equipment. The performance degradation of IGBT gate oxide layer is one of the important failure modes. In view of failure mechanism analysis and easy implementation of monitoring circuit, this paper selects the gate leakage current of IGBT as the precursor parameter of gate oxide degradation, and uses time domain characteristic analysis, gray correlation degree, Mahalanobis distance, Kalman filter and other methods to carry out feature selection and fusion, and finally obtains a health indicator characterizing the degradation of IGBT gate oxide. Based on the Convolutional Neural Network and Long Short-Term Memory (CNN-LSTM) network, this paper constructs an IGBT gate oxide degradation prediction model, and performs experimental analysis on the dataset released by NASA-Ames Laboratory, and the average absolute error of performance degradation prediction is as low as 0.0216. Compared with Long Short-Term Memory (LSTM), Convolutional Neural Network (CNN), Support Vector Regression (SVR) and CNN-LSTM models, CNN-LSTM network has the highest prediction accuracy. These results show the feasibility of gate leakage current as a precursor parameter of IGBT gate oxide layer failure, as well as the accuracy and reliability of the CNN-LSTM prediction model.

As common industrial by-products, airborne engineered nanomaterials are considered important environmental toxicants to monitor due to their potential health risks to humans and animals. The main uptake routes of airborne nanoparticles are nasal and/or oral inhalation, which are known to enable the transfer of nanomaterials into the blood stream resulting in rapid distribution in the body. Consequently, mucosal barriers present in nose, buccal and lung have been identified and intensively studied as the key tissue barrier to nanoparticle translocation. Despite decades of research, surprisingly little is known about the differences among various mucosa tissue types to tolerate nanoparticle exposures. One limitation in comparing nanotoxicological data sets can be linked to a lack of harmonization and standardization of cell-based assays, where a) different cultivation conditions such as air-liquid interface or submerged cultures, b) varying barrier maturity and c) diverse media substitutes have been used. The current comparative nanotoxicological study therefore aims at analyzing the toxic effects of nanomaterials on four human mucosa barrier models including nasal (RPMI2650), buccal (TR146), alveolar (A549), and bronchial (Calu-3) mucosal cell lines to better understand the modulating effects of tissue maturity, cultivation conditions and tissue type using standard Transwell cultivations at liquid-liquid and air-liquid interfaces. Overall, cell size, confluency, tight junction localization, and cell viability as well as barrier formation using 50% and 100% confluency was monitored using trans-epithelial-electrical resistance (TEER) measurements and Presto Blue assays of immature (e.g. 5 days) and mature (e.g. 22 days) cultures in the presence and absence of corticosteroids such as hydrocortisone. Results of our study show that cellular responses to increasing nanoparticle exposures are highly cell type specific, where bronchial mucosal cell barriers models cultivated under ALI conditions showed less tolerance to acute ZnO nanoparticle exposures. Additionally, stronger toxicities are found using early mucosa barriers compared to later barrier models being maturated under air-liquid cultivation conditions.

Background: Despite the existence of a wide variety of anti-inflammatory drugs, the vast majority are classified as steroidal or non-steroidal. Both classes with many side effects that limit usage. Thus, the search for new molecules with anti-inflammatory potential is still important. Methods: Five phenylbenzohydrazides were synthetized and evaluated in pre-clinical models of acute inflammation in vivo and in vitro. Results: Substances significantly reduced cell migration induced by carrageenan. It was also observed an intense inhibition in protein extravasation and cytokines (IL-6, IL-1β, and TNF-α) production as well as nitric oxide reduction. INL-11 demonstrated to be the most potent since the reduction was significant even when compared with dexamethasone. In vitro INLs also reduced cytokines and NO production and iNOS activity. INL-11 was the most effective in reducing cell migration in vitro. Conclusions: our data suggest that these substances are suitable for further development to new series of compounds that could lead to new hits and future drug prototypes for anti-inflammatory conditions.

We experimentally demonstrate enhanced spectral broadening of femtosecond optical pulses after propagation through silicon-on-insulator (SOI) nanowire waveguides integrated with two-dimensional (2D) graphene oxide (GO) films. Owing to the strong mode overlap between the SOI nanowires and the GO films with a high Kerr nonlinearity, the self-phase modulation (SPM) process in the hybrid waveguides is significantly enhanced, resulting in greatly improved spectral broadening of the femtosecond optical pulses. A solution-based, transfer-free coating method is used to integrate GO films onto the SOI nanowires with precise control of the film thickness. Detailed SPM measurements using femtosecond optical pulses are carried out, achieving a broadening factor of up to ~4.3 for a device with 0.4-mm-long, 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of ~3.5 and the effective nonlinear figure of merit (FOM) by a factor of ~3.8, relative to the uncoated waveguide. Finally, we discuss the influence of GO film length on the spectral broadening and compare the nonlinear optical performance of different integrated waveguides coated with GO films. These results confirm the improved nonlinear optical performance for silicon devices integrated with 2D GO films.

Two once-through steam generators and a combination of a steam generator and a gas preheater for supplying feed gases to solid-oxide electrolysis stacks were evaluated for their carryover characteristics of contaminants from the feed-water into the steam phase. The concentrations of various trace impurities in the steam were determined by sampling the steam condensates and screening them with inductively coupled plasma - mass spectrometry for 19 elements and liquid ion chromatography and continuous flow analysis for chloride and ammonium. Steam soluble species like boric acid undergo complete volatilization and transfer into the steam phase. During unstable evaporation in the steam generators an extensive physical carryover of alloying metal species was observed. At realistic operation conditions for steam electrolysis, the gas preheater caused a considerable release of silicon into the steam phase. Two stack experiments were performed with common preheater temperatures and showed largely increased cell voltage degradation at higher operation temperatures. The post-test chemical analysis of cell samples revealed significant concentrations of silicon in the samples that are regarded as primary cause for increased degradation. These findings could partially explain the wide spread of degradation rates reported for solid-oxide steam electrolysis experiments.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.

In this work, we investigate by ab initio calculations and optical experiments the sensitiv- ity of graphene quantum dots in their use as devices to measure the presence, and concentration, of heavy metals in water. We demonstrate that the quenching or enhancement in the optical response (absorption, emission) depends on the metallic ion considered. In particular, two test cases of opposite behaviour are considered: Cd 2+ , where we observe an increase in the optical response for increasing concentration, and Pb 2 whose emission spectra are quenched along the concentration rise. We envisage that quantum dots of graphene may be routinely used as cheap detectors to measure the degree of poisoning ions in water

Because of some of their diverse benefits, intelligent textiles have attracted a great deal of interest among specialists over the past decade. This paper describes a novel approach to the manufacture of intelligent piezoelectric polymer-based textiles with enhanced piezoelectric responses for applications that extract biomechanical energy. Here we report a highly scalable and ultrafast production of smart textile piezoelectric containing graphene oxide nanosheets (GONS) dispersed in polyvinylidene fluoride (PVDF). In this work, Cotton textiles (CT) were functionalized and by graphene oxide (GO), using PVDF as a binder to obtain a CT-PVDF-GO material. Tetraethyl orthosilicate (TEOS) was further grafted as a coating layer to improve the surface compatibility, resulting in the CT-PVDF-GO-TEOS composite. The research results show that the addition of GONS significantly improves PVDF's overall crystallization rate on CT. More specifically, the piezoelectric β-phase content (100 % higher F[β]) and crystallinity degree on the piezoelectric properties of composite cotton fiber has been improved effectively. Consequently, this fabricated piezo-smart textile has a glorious piezoelectricity even with comparatively low coating content of PVDF-GONS-TEOS. Based on it, the as-fabricated piezoelectric textile device has resulted in the output voltage of up to 13 mV for a given frequency (fm = 8 Hz) at fixed strain amplitude value (0.5 %). It is believed that this research may further reveal the field of energy harvesting for possible applications in the future.. In addition, the set of experimental results that illustrate the smart textile was carried out and discussed, and how it can be used as a wearable device source for this smart textile. Finally, the approach described in this study can also be used to construct other desirable designs, for a wearable low-consumption sensor, etc.

Here we report the effect of substrate, sonication process, and post-annealing on the structural, morphological, and optical properties of ZnO thin films grown in the presence of isopropyl alcohol (IPA) at temperature 30 – 65 ℃ by successive ionic layer adsorption and reaction (SILAR) method on both soda lime glass (SLG) and Cu foil. The X-ray diffraction (XRD) patterns confirmed the preferential growth thin films along (002) and (101) plane of wurtzite ZnO structure while grown on SLG and Cu foil substrate respectively. Both XRD and Raman spectra confirmed the ZnO and Cu-oxide phases of the deposited films. Scanning electron microscope (SEM) image of the deposited films shows compact and uniformly distributed grains for samples grown without sonication while using IPA at temperature 50 and 65 ℃. The post-annealing treatment improves the crystallinity of the films, further evident by XRD and transmission and reflection results. The estimated optical bandgaps are in the range of 3.37-3.48 eV for as-grown samples. Results revealed that high-quality ZnO thin films could be grown without sonication using IPA dispersant at 50 ℃, which is much lower than the reported results using the SILAR method. This study suggests that in the presence of IPA, the SLG substrate results in better c-axis oriented ZnO thin films than that of DI water, ethylene glycol, propylene glycol at the optimum temperature of 50 ℃. Air-annealing of the samples grown on Cu foils induced the formation of Cu_xO/ZnO junctions which is evident from the characteristic I-V curve including the structural and optical data.

Greenhouse Gases (GHG) emissions from dairy farms are significant contributors to global warming. However much of the published work on GHG reduction is focused on either Methane (CH4) or Nitrous Oxide (N2O), with few, if any, considering the interactions that changes to farm systems can have on both gases. This paper takes the raw data from a year of activity on a 300 cow commercial dairy farm in Northern Ireland to more accurately quantify the GHG sources by use of a simple predictive model based on IPCC methodology. Differing herd management policies are examined together with the impact of integrating Anaerobic Digestion (AD) into each farm system. Whilst significant success can be predicted in capturing CH4 and Carbon Dioxide (CO2) as biogas and preventing N2O emissions, gains made can be lost in a subsequent process negating some or all of the advantage. The process of extracting value from the captured resource is discussed in the light of current farm parameters together with indications of other potential revenue streams. However, this study has concluded that despite the significant potential for GHG reduction, there is little incentive for widespread adoption of manure based farm scale AD in the UK at this time.

A biomimetic, ion-imprinted polymer (IIP) was prepared by electropolymerization of pyrrole at the surface of gold electrodes decorated with vertically grown ZnO nanorods. The vertical growth of the nanorods was achieved via an ultrathin aryl monolayer grafted by reduction of diazonium salt precursor. Pyrrole was polymerized in the presence of L-cysteine as chelatant agent and Hg(II) (template). Hg(II)-imprinted polypyrrole (PPy) was also prepared on bare gold electrode in order to compare the two methods of sensor design (Au-ZnO-IIP vs Au-IIP). Non-imprinted PPy was prepared in the same conditions, however in the absence of any Hg2+ template. The strategy combining diazonium salt modification and ZnO nanorod decoration of gold electrodes permitted to increase considerably the specific surface and thus to improve the sensor performances. The limit of detection (LOD) of the designed sensor was ~1 pM, the lowest value ever reported in literature. The dissociation constants between PPy and Hg2+ were estimated at [Kd1 = (7.89 ± 3.63) mM and Kd2 = (38.10 ± 9.22) pM]. The sensitivity of the designed sensor was found to be 0.692 ± 0.034 μA/pM. The Au-ZnO-IIP was found to be highly selective towards Hg(II) compared to cadmium, lead and copper ions. This sensor design strategy could open up new horizons in monitoring toxic heavy metal ions in water and therefore contribute to enhance environmental quality.