To implement renewable energy resources, microgrid systems have been adopted and developed into the technology of choice to assure mass electrification in the next decade. Microgrid systems have a number of advantages over the conventional utility grid systems, however, it faces severe instability issues due to continually increasing constant power loads. To improve the stability of the entire system, load side compensation technique is chosen because of its robustness and cost effectiveness. In this particular occasion, a sliding mode controller is developed for microgrid system in the presence of CPL to assure certain control objective of keeping the output voltage constant at 480V. After that, the robustness analysis of the sliding mode controller against parametric uncertainties is presented. The sliding mode controller robustness against parametric uncertainties, frequency variations, and additive white Gaussian noise (AWGN) are illustrated in this paper. Later, the performance of the PID and sliding Mode controller is compared in case of nonlinearity, parameter uncertainties, and noise rejection to justify the selection of Sliding Mode controller over PID controller. All the necessary calculations are reckoned mathematically and results are verified in the virtual platform such as MATLAB/Simulink with the appreciable outcome.

The composition of the gut microbiota varies significantly among healthy individuals and insomniacs, hypersomniacs and healthy people. On the other hand, there is a substantial bacterial strain shared across these populations with distinct intra-population, mother-to-infant and intra-household transmission patterns. Based on these premises, we propose a hypothesis stating that person-to-person bacterial transmission can change the sleep pattern in couples. In this pilot study, 157 couples who had been married and living together for an average of 5.91 months were enrolled. A wide range of questionnaires were administered to participants to measure sleep patterns. Gut microbiota composition was analyzed at two time points: baseline and 3 months. We found that sleep disturbances in couples can be partially explained by changes in gut microbiota.

Agriculture is the largest sector of Nepalese economy among the south-Asian developing countries that contributed 26.98 % share of Gross Domestic Product (GDP) in the year 2018/19. The capacity to derive maximum output by per unit of resource is resource use efficiency. Resource use efficiency of a producer explains the comparison between inputs and output value. Potato is staple vegetable in every parts of Nepal. Cobb-Douglas production function is used to predict the significance of inputs in income from cash crops. Due to lack of optimum utilization of available resources in cultivation of vegetable like lack of technical knowledge, low education level, and extensive service the productivity and production is low in Nepalese economy. It ensures vegetable security in Nepal. Though, there are extensive researches on the resource use efficiency and productivity issues on agriculture, very few papers explored in the case of Sudurpaschim province of Nepal OBJECTIVE: This study had the specific purposes: (1) To identify the factors affecting in resource use efficiency and productivity of potato production (2) to utilize the resource use efficiency and productivity in potato production and (3) to show the type of returns to scale in potato production. METHODS: Applying post-positivist paradigm and quantitative causal survey research design, it explored the resource use efficiency and productivity through the semi-structured questionnaire from 140 households by random sampling. Data analysis was carried out by multiple regression model using Cobb-Douglas production function. SPSS software was used to find quantitative results. From the analysis of data using mean, and SD, t-test, analysis of variance, Durbin-Waston test, Marginal Value Product and marginal Factor cost, findings of this research was emerged. RESULTS AND DISCUSSION: The major findings: education level, extension service, farm size and pesticide cost were significant variables in potato production; seed, hired labor, Family Yard Manure and pesticide cost were overused and needed to decrease their cost for optimum allocation and there was decreasing returns to scale in production. This study emphasized on increasing education level, extensive service and farm size for optimum utilization of resources and increasing returns to scale. SIGNIFICANCE: Barriers to Indian potatoes and increasing returns to scale are only possible through protection policy of government. For optimum use of resources and increasing returns to scale, government can introduce capital intensive technique. This study can be implied in policy making and improving existing situation of agriculture, and allocating budget.

: Based on fairness perspective, this paper combines the social vulnerability assessment of natural hazards with multi-objective site selection model to propose a new site selection planning model for central refuges. To begin with, the social vulnerability assessment system of regional natural disasters is founded through literature analysis, and the social vulnerability index of natural disasters is constructed; and based on the exponential differentiation of index to depict regional refuge demand, design vulnerability coverage function quantitive site selection fairness; then taking the shortest weighted evacuation distance, maximum vulnerability coverage and construction cost, the coverage population and refuge quantity as constraint conditions to construct multi-objective optimization model; finally, taking Zigong City, Sichuan Province as the object of empirical research, adapting NSGA-II algorithm to get the Pareto optimal solution set, and using TOPSIS method to get the optimal location scheme. The research results can provide a new method for the location layout of central refuge.

Chili peppers (Capsicum annuum L.) are economically important crop worldwide. Pepper yellow leaf cure Thailand virus (PepYLCTHV), a Begomovirus causing yellow leaf mosaic disease of chili pepper has been reported to damage 95% economic loss under favorable epidemic conditions. Thirty-one chili genotypes were screened for resistance to PepYLCTHV disease through challenge inoculation using 10-15 viruliferous whiteflies per plant. We purified two resistant lines (PEP6 and PEP12) through four generations of selfing and selection through challenged inoculations. At the 28 days after inoculations two chili genotypes showed symptoms less based on disease severity and percentage of disease incidence of 30 plants PEP6 showed a disease severity 3.64 with 69.33 % DI and PEP12 showed a disease severity 3.83 with 77.67 % DI. PEP6 and PEP12 were selected for pure-line development for four cycles.Both varieties showed an increase in percentage of the resistant plant 12.78 % and 16.77 %, respectively. These lines have potential for release as resistant lines for improvement chili pepper resistance to PepYLCTHV and for developing maker associated with the resistant trait.

A number of studies suggested that influenza vaccination can provide protection against COVID-19 but the underlying mechanisms that could explain this association is still unclear. In this study, the effect of the 2021/2022 seasonal influenza vaccination on the immune response to the booster dose of anti-SARS-CoV-2 vaccination was evaluated in a cohort of healthy individuals. One hundred and thirteen participants were enrolled, and 74 of them with no prior COVID-19 diagnosis or significant co-morbidities were considered for the analysis. Participants received the anti-influenza tetravalent vaccine and the booster dose of the anti-SARS-CoV-2 vaccine or the anti-SARS-CoV-2 vaccine alone. Blood was collected before and 4 weeks after each vaccination and 12 weeks after SARSCoV2 vaccination and analyzed for anti-flu and anti-spike-specific antibody titers and for in vitro influenza and SARS-CoV-2 neutralization capacity. Results indicated an increased reactivity in subjects who received both influenza and SARSCoV2 vaccinations, as compared to those who received only the SARS-CoV-2 vaccine, with sustained anti-spike antibody titers up to 12 weeks post-vaccination. Immune response to influenza vaccine was evaluated and individuals were stratified as high or low responders. High responders showed increased antibody titers against SARSCoV2 vaccine both after 4- and 12-weeks post-vaccination. On the contrary, the individuals classified as low responders were less responsive to the SARS-CoV-2 vaccine. These data indicate that both external stimuli, such as influenza vaccination, and the host's intrinsic ability to respond to stimuli play a role in the response to vaccine.

Background: Currently, a Dolutegravir (DTG)-based regimen is administered to women on option B plus to prevent mother-to-child transmission (MTCT) of the virus. However, its effect on reducing MTCT of human immunodeficiency virus (HIV) among exposed infants over the previously used Efavirenz (EFV)-based regimen is unknown. Objective: This study aimed to compare the effects of DTG-based and EFV-based regimens on the MTCT of HIV among exposed infants in southern Ethiopia. Methods: A retrospective before-after study design was employed from March to May 2023 among 958 mother-infant pairs (479 on EFV-based and 479 on DTG-based regimens) enrolled in the prevent mother-to-child transmission (PMTCT) care from September 2015 to February 2023. The outcome variable was the HIV infection status among the exposed infants. A log-binomial model was employed and the proportion was computed to compare the incidence of MTCT of HIV in both groups. The risk ratio (RR) with 95% confidence interval (CI) was calculated to assess the predictor variables. Results: Mothers on a DTG-based regimen were approximately 44% (adjusted risk ratio (aRR): 0.56; 95% CI: 0.44, 0.70) less likely to transmit HIV to their infants than those on an EFV-based regimen. In addition, poor/fair adherence to antiretroviral therapy (ART) (aRR: 5.82; 95% CI: 3.41, 9.93), home delivery (aRR: 3.61; 95% CI: 2.32, 5.62), mixed feeding practice (aRR: 1.83; 95% CI: 1.45, 2.3), and not receiving antiretroviral prophylaxis (aRR: 3.26; 95% CI: 1.6, 6.64) were found to increase the risk of MTCT of HIV infection, whereas older maternal age (aRR: 0.93; 95% CI: 0.9, 0.96) was a protective factor.Conclusion: The Dolutegravir-based regimen significantly reduced MTCT of HIV among exposed infants compared to the EFV-based regimen. Thus, DTG-based first-line ART regimen supplementation should be sustained to achieve global and national targets for zero new infections in HIV-exposed infants.

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

Addressing the increasing nursing demand in the face of a limited nursing workforce, understanding job satisfaction and retention becomes critical. Our cross-sectional study, conducted among 2,572 nurses in Bavaria, Germany, uncovers a dichotomy where nurses have strong empathy for their profession yet yearn for significant improvements. The top areas identified for enhancement include (i) ensuring sufficient time for patient care, (ii) providing a reliable service organization with minimal unplanned shift changes, and (iii) streamlining nursing documentation. Moreover, the largest disparity between expectations and job satisfaction was measured in patient care time. Multivariable regression analysis further investigates factors influencing intentions to stay in the profession, including (i) demographic aspects (age, living conditions), (ii) working area, (iii) working hours, (iv) career choice satisfaction, (v) career opportunities, (vi) payment, (vii) working and rest times, and (viii) satisfaction derived from aiding individuals in challenging life situations. The findings uncover a need to change nursing conditions, and measures for younger nurses and elderly care nursing. Although there are limitations, and a potential bias due to convenience sampling, our study provides key insights into nursing conditions. Future research should broaden its scope to investigate nurse job satisfaction and retention, emphasizing potential relief tools such as digitization.

To meet the International Maritime Organization’s requirements for carbon dioxide emissions from ships, a cost-effective and practical ship decarbonization tower was autonomously designed based on the marine diesel engine model 6135G128ZCa. The tower is internally filled with structured packing, and a slot-type liquid distributor at the top of the packing evenly distributes the NaOH solution to absorb carbon dioxide from the ship’s exhaust gas. Experimental research was conducted to investigate the influence of factors such as liquid-to-gas ratio and NaOH concentration on the performance of the decarbonization tower. The results confirmed that the use of NaOH solution can effectively absorb CO2 from ship exhaust gas, reducing CO2 emissions by more than 81.59% and meeting the EEDI (Energy Efficiency Design Index) requirements specified by the IMO.

In the realm of artificial intelligence (AI), generative systems, most notably Midjourney, have tremendous power to generate creative images of buildings and sites of Islamic architectural heritage through text-to-image generation based on the internet. The AI-generated representations have significant potential for architects, specialists, and common users. However, the system has considerable limitations when generating images for some buildings and sites where the representations appear too far from their original represented structures. This research article attempts to answer the question: What are the limitations of using the AI system of Midjourney in producing images similar to the original buildings and sites of the Islamic architectural heritage? The research employs prompt engineering techniques based on historical sources as inputs to examine the accuracy of the output of the AI-generated images of selected examples of structures of the Islamic tradition. It compares the output with the original look by employing direct observation and critical analysis of human intelligence (HI). It categorizes these limitations into four groups: (1) limits of the prompt, (2) limits of fame, (3) limits of regionality and historical styles, and (4) limits of architectural elements and details. It concludes that while Midjourney has great capability to represent high-end AI-generated images inspired by the Islamic tradition, it currently falls short of presenting the actual appearance of some of their original structures.

This work focuses on an inland area of North Sardinia (Italy), which is currently subject to depopulation and economic crisis because it is not affected by the summer tourism typical of the region. Despite this, the area shows an interesting architectural and natural heritage, as of today insufficiently known and valued. Therefore, the purpose of this paper is to illustrate the application of the Conjoint Analysis methodology on this case study aimed at supporting processes of valorisation, diversification of the tourist offer and promotion of the through the detection of the preferences of a sample of residents and visitors on a set of 9 cards (itinerary profiles) which also promote the peculiarities of small rural centres. Thus, by valorising the material and immaterial heritage and their intrinsic characteristics, it is shown that inland areas can generate an economy by offering new types of tourism, not just the typically invasive summer and maritime tourism. The research, therefore, seeks to estimate the economic value of the area from a public point of view through the WTP measured by a questionnaire of 600 interviews between inhabitants (300) and tourists (299).

Food Neophobia (FN), defined as the reluctance to eat new or unfamiliar foods, mainly concerns fruit, vegetables, and legumes, typical of the Mediterranean Diet (MD). Considering these premises, this study aimed to clarify the relationship between FN and AMD in a sample of Italian children and their association with some socio-demographic factors and children's nutritional status. A sample of 288 children aged 3-11 years, participated to an assessment carried out with a questionnaire evaluating FN and AMD, respectively with Child Food Neophobia Scale (CFNS) and the KIDMED Test. Most of the sample showed an intermediate (67.3%) or high level of FN (18.1%) with high rates among 6-11 years old children (63.9%) and especially in only-child (50%). The AMD was mostly low (29.5%) or medium (54.8%) and reached lower levels among higher neophobic children (51.9%; p value < 0.05). Present results confirm the study hypothesis that FN is a driver of MD abandonment and show the positive effects on children's eating habits of having siblings. Finally, this study proves the relevance of adopting effective feeding strategies against FN to avoid its maintenance in adulthood and detrimental effects on future overall health and well-being.

Canine mammary tumors represent one of the leading malignant pathology in female dogs, displaying the importance of efficient therapeutic findings, beside the golden standard surgery, able to limit the development of the disease. Studies in human cancers demonstrated that Doxorubicin presents a good effect in different biological processes like apoptosis, autophagy, cell cycle, cell invasion and epithelial to mesenchymal transition. Our study following the effects of Doxorubicin on two canine mammary cancer cell lines P114 and CMT-U27, showing an inhibitory effect in cell proliferation and an expression alteration of the EMT related genes.

The cutting of difficult-to-machine materials, including their preconditioning, often requires specialised tools and machinery. An alternative processing technology can be cutting materials with a water jet. From the initial stage, the selection of appropriate technological parameters will influence what further finishing treatments will be applied. Vibrations occurring during this process can negatively affect the quality of the cutting edges and surfaces. Therefore, this study analysed vibrations during water-jet cutting with variable technological parameters (speed vfi and pressure pi). To measure the vibrations, a three-axis accelerometer from SEQUOIA was used in water-jet cutting of three materials: aluminum alloy, titanium alloy, and steel. Based on the study, it was found that the maximum value of vibration amplitude reaches the lowest value of vibration acceleration for aluminum alloy (not exceeding 5 m/s2), regardless of the value of pressure during the cutting process. This, taking into account the material properties, indicates that aluminum alloy is the material most susceptible to the cutting process while maintaining a high quality of the cutting surface. Significantly higher values of vibration acceleration amplitude (reaching up to 60 m/s2) during cutting were registered for steel and titanium alloy in all zones and phases of the process (entry zone, cutting zone, and exit zones).

Graphene is a two-dimensional nanostructured material with intrinsic properties that show promising performance in various applications, including electronics, renewable energy, medicine, mechanical enforcement and others. This study reports a bottom-up approach for the conversion of cyclohexane into graphene nanoflakes, which were then deposited onto fiberglass using a non-thermal generator. The composite was characterized using transmission electron microscopy, which revealed the formation of stacked few-layer graphene with a partially disordered structure and a d-spacing of 0.358 nm between the layers. X-ray diffraction confirmed the observations from the TEM images. SEM images showed the agglomeration of carbonaceous material onto the fiberglass, which experienced some delamination due to the synthesis method. Raman spectroscopy indicated that the obtained graphene exhibited a predominance of defects in its structure. Additionally, Atomic Force Microscopy (AFM) analyses revealed the formation of graphene layers with varying levels of porosity.

In this paper, a novel strategy is adopted in a degradation model to affect the implied lifetime distribution. The multiplicative degradation model is utilized as a postulate in the model. It will be established that the implied lifetime distribution forms a classical mixture model. In this mixture model, time-to-failure is lying with some probabilities between two first passage times of the degradation process to reach two specified levels. Stochastic comparisons in the model under a change in the probabilities are studied. Several examples are provided to highlight the applicability of the results in the cases when typical degradation models are candidate.

Epithelial ovarian cancer (EOC) remains the most lethal gynecologic malignancy, largely due to metastasis and drug resistant recurrences. Fifteen percent of ovarian tumors carry mutations in BRCA1 or BRCA2, rendering them vulnerable to treatment with PARP inhibitors such as olaparib. Recent studies have shown that TGFβ can induce “BRCAness” in BRCA wild-type cancer cells. Given that TGFβ is a known driver of epithelial to mesenchymal transition (EMT), and the con-nection between EMT and metastatic spread in EOC and other cancers, we asked if TGFβ and EMT alter susceptibility of EOC to PARP inhibition. Epithelial EOC cells were transiently treated with soluble TGFβ and their clonogenic potential, expression and function of EMT and DNA repair genes, and response to PARP inhibitors compared with untreated controls. A second epithelial cell line was compared to its mesenchymal derivative for EMT and DNA repair gene expression and drug responses. We found that TGFβ and EMT resulted in downregulation of genes responsible for homologous recombination (HR) and sensitized cells to olaparib. HR efficiency was reduced in a dose-dependent manner. Furthermore, mesenchymal cells displayed sensitivity to olaparib, cis-platin, and the DNA-PK inhibitor Nu-7441. Therefore, treatment of disseminated, mesenchymal tumors may represent an opportunity to expand clinical utility of PARP inhibitors and similar agents.

The article presents the results of a morpho-physiological assessment of rice samples by the strength of growth, as well as an assessment of the degree of development of the conducting system of the flag leaves of rice plants. The resistance of varieties to flooding is very relevant in the fight against weeds due to the deep layer of water that weeds cannot overcome. Currently, there are no zoned varieties in Russia that would meet these requirements. Therefore, the problem of creating such rice varieties is urgent, as it will reduce production costs, reduce grain losses during harvesting, improve the quality of the products obtained, and also reduce the pesticide load on the ecosystem. As a result of research, a number of studied samples revealed the potential to quickly lengthen the first leaves, overcome a large layer of water and accumulate vegetative mass. As a result of the evaluation of the conducting system of the flag leaf of rice plants, it was found that in plants with the flood resistance gene Sub1A, which stops growth under water, the conductive beams were smaller in comparison with other fast-growing samples with the AG, Sk genes. Consequently, fast-growing samples have bigger sizes of the conducting system as a resistance mechanism.

Since the beginning of 2020, tetracycline (TC), such as minocycline (MINO), has been used to inhibit coronavirus disease 2019 (COVID-19). Traditional Japanese Kampo medicine, such as Saiko-keishi-to (SKT), has recently received a lot of attention for its anti-severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) effects. We describe a COVID-19 patient treated with MINO and SKT in anticipation of their anti-SARS-CoV-2 properties. A 90-year-old male patient with Alzheimer’s disease was referred to a medical clinic due to fever, appetite loss, and general malaise. Based on positive SARS-CoV-2 rapid antigen tests, he was diagnosed with COVID-19. He did not have COVID-19 pneumonia, but he had difficulty in eating on his own. As a result, he was referred to a hospital for admission. After admission, he was treated with molnupiravir to avoid aggravation. Seven days after his admission, he was discharged. After his discharge, he was referred to our hospital as an outpatient due to a prolonged mild fever and general malaise. As a precaution, a real-time reverse transcription-polymerase chain reaction (RT-PCR) test was performed, which yielded a positive result. Therefore, the aforementioned symptoms were thought to be caused by prolonged COVID-19. He was treated with MINO and SKT due to the anti-viral properties of these two drugs. The RT-PCR test became negative 7 days after receiving this treatment, and the fever and general malaise subsided.

The gauge field equation for fluid mechanics established in Part 1 is developed into a first-order scattering theory in the simplified case of a two-dimensional incompressible flow over a flat plate. This is used to present a model for the origin of Tollmien-Schlichting (TS) waves based on scattering between fluid particles. As a result, analytical formulae for the maximum amplification factor and the transition point from laminar to turbulent flow in the boundary layer are obtained. The mathematical transformations from the stationary field equations in Part 1 to a scattering theory with time evolution along the flow axis using Wick rotation are elaborated in detail.

Food waste is one of the greatest challenge to sustainability in developed and developing countries. In the former, food waste is concentrated in the final part of the chain. Too Good To Go is a digital platform aimed to prevent food waste, where consumers can buy magic boxes from different outlets containing food products that are approaching their end-of-life. However, the mechanism of the platform enable the outlets to publish their offering much in advance of the pick-up time, raising the question whether the food sold on the platform is effectively a leftover or a planned production. Our empirical study gathers data from over 1200 outlets in Rome on the Too Good To Go platform.

Deep neural networks have been extensively researched in the field of document image classification to improve classification performance and have shown excellent results. However, there is little research in this area that addresses the question of how well these models would perform in a real-world environment, where the data the models are confronted with often exhibits various types of noise or distortion. In this work, we present two separate benchmark datasets, namely RVL-CDIP-D and Tobacco3482-D, to evaluate the robustness of existing state-of-the-art document image classifiers to different types of data distortions that are commonly encountered in the real world. The proposed benchmarks are generated by inserting 21 different types of data distortions with varying severity levels into the well-known document datasets RVL-CDIP and Tobacco3482, respectively, which are then used to quantitatively evaluate the impact of the different distortion types on the performance of latest document image classifiers. In doing so, we show that while the higher accuracy models also exhibit relatively higher robustness, they still severely underperform on some specific distortions, with their classification accuracies dropping from ~90% to as low as ~40% in some cases. We also show that some of these high accuracy models perform even worse than the baseline AlexNet model in the presence of distortions, with the relative decline in their accuracy sometimes reaching as high as 300-450% that of AlexNet. The proposed robustness benchmarks are made available to the community and may aid future research in this area.

Previous studies have quantified repolarization variability using time-domain, frequency-domain and non-linear analysis in mouse hearts. Here, we investigated the relationship between these parameters and ventricular arrhythmogenicity in a hypokalaemia model of acquired long QT syndrome. Methods: Left ventricular monophasic action potentials (MAPs) were recorded during right ventricular regular 8 Hz pacing during normokalaemia (5.2 mM [K+]), hypokalaemia modelling LQTS (3 mM [K+]) or hypokalaemia with 0.1 mM heptanol in Langendorff-perfused mouse hearts. Results: During normokalaemia, mean APD was 33.5±3.7 ms. Standard deviation (SD) of APDs was 0.63±0.33 ms, coefficient of variation was 1.9±1.0% and the root mean square (RMS) of successive differences in APDs was 0.3±0.1 ms. Low- and high-frequency peaks were 0.6±0.5 and 2.3±0.7 Hz, respectively, with percentage powers of 38±22 and 61±23%. Poincaré plots of APDn+1 against APDn revealed ellipsoid morphologies with SD along the line-of-identity (SD2) to SD perpendicular to the line-of-identity (SD1) ratio of 4.6±1.1. Approximate and sample entropy were 0.49±0.12 and 0.64±0.29, respectively. Detrended fluctuation analysis revealed short- and long-term fluctuation slopes of 1.62±0.27 and 0.60±0.18, respectively. Hypokalaemia provoked ventricular tachycardia in six of seven hearts, prolonged APDs (51.2±7.9 ms), decreased SD2/SD1 ratio (3.1±1.0), increased approximate and sample entropy (0.68±0.08 and 1.02±0.33) and decreased short-term fluctuation slope (1.23 ± 0.20) (ANOVA, P<0.05). Heptanol prevented VT in all hearts studied without further altering the above repolarization parameters observed during hypokalaemia. Conclusion: Reduced SD2/SD1, increased entropy and decreased short-term fluctuation slope are associated with ventricular arrhythmogenesis in hypokalaemia. Heptanol exerts anti-arrhythmic effects without affecting repolarization variability.

Novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) variants of concern (VOC) are constantly threatening global public health. With no end date, the pandemic still persists with the emergence of novel variants that threaten the effectiveness of diagnostic tests and vaccines. Mutations in the Spike surface protein of the virus are regularly observed in the new variants, potentializing the emergence of novel viruses with different tropism from the current ones, which may change the severity and symptoms of the disease. Growing evidence has shown that mutations are being selected in favor of variants that are more capable of evading the action of neutralizing antibodies. In this context, the most important factor guiding the evolution of SARS-CoV-2 is its interaction with the host’s immune system. Thus, as current vaccines cannot block the transmission of the virus, measures complementary to vaccination, such as the use of masks, hand hygiene, and keeping environments ventilated remain essential to delay the emergence of new variants. Importantly, in addition to the involvement of the immune system in the evolution of the virus, we highlight several chemical parameters that influence the molecular interactions between viruses and host cells during invasion and are also critical tools making novel variants more transmissible. In this review, we dissect the impacts of the Spike mutations on biological parameters such as (1) increase of Spike binding affinity to hACE2; (2) bound time for the receptor to be cleaved by the proteases; (3) how mutations associate with increase of RBD up-conformation state in the Spike ectodomain; (4) expansion of uncleaved Spike protein in the virion particles; (5) increment of Spike concentration per virion particles; and (6) evasion of the immune system. These factors play key roles in the fast spreading of SARS-CoV-2 variants of concern, including the Omicron.

This paper describes the successful application of the Transformer model used in the natural language processing and vision tasks as a means of processing the time series of signals from gyroscope and accelerometer sensors for the classification of human activities. The Transformer model is based on deep neural networks with many layers which can generalize well on signals. All measured signals come from a smartphone placed in a waist bag. Activity prediction is sequence-to-sequence, each time step of the signal is assigned a designation of the performed activity. Emphasis is placed on attention mechanisms, which express individual dependencies between signal values within a time series. In comparison with another recent result, the recognition precision was improved from 89.67 percent to 99.2 percent. The transformer model should in the future be included among the top options in machine learning methods for human activity recognition.

As V2X technology develops, acute problems related to reliable and secure information exchange between network objects in real time appear. The article aims to solve the scientific problem of building a network architecture for reliable delivery of correct and uncompromised data within the V2X concept to improve the safety of road users, using blockchain technology and mobile edge computing (MEC). The authors present a formalized mathematical model of the system, taking into account the interconnection of objects and V2X information channels, and an energy-efficient algorithm of traffic offloading to the MEC server. The paper presents the results of application of blockchain technologies and mobile edge computing in the developed system, their description, evaluation of advantages and disadvantages of the implementation.

Sustainability is very important in business. The residential high-rise building all firms wanted to successful and sustainability in business. There is need the construction to completed low time, low cost and high quality in construction work. Therefore, real estate developers must find various strategies to use in construction projects to achieve goals and success of the firm. The purpose of this study was to indicate the very importance of knowledge management can lead to sustainability in business. Analyze 14 critical success to sustainability in residential high-rise building projects, collected questions from literature review, and survey in deep interview senior managers of 15 projects real estate development firms listed on the stock market of Thailand. Budget building more than 1000 million baht per project. From conceptual frame work five foundations integrated to knowledge management of critical success (KMITL PROCESS) used made tool survey in deep interview the critical success to sustainability in residential high-rise building project from project managers. Used IBM SPSS evaluated the critical success to sustainability. Found was one very important of critical success to sustainability, which was quality of products x̄ = 4.83. All 14 critical success to sustainability was found can applied made the knowledge management of critical success to sustainability in residential high-rise building project in firm. Especially in the field of construction managements project can used improve of all construction projects.

We show that an exponential income distribution will emerge spontaneously in a peer-to-peer economic network that shares the publicly available technology. Based on this finding, we identify the exponential income distribution as the benchmark structure of the well-functioning market economy. However, a real market economy may deviate from the well-functioning market economy. We show that the deviation is partly reflected as the invalidity of exponential distribution in describing the super-low income class that involves unemployment. In this regard, we find, theoretically, that the lower-bound u of exponential income distribution has a linear relationship with (per capita) unemployment compensation. In this paper, we test this relationship for the United Kingdom from 2001 to 2015. Our empirical investigation confirms that the income structure of low and middle classes (about 90% of populations) in the United Kingdom exactly obeys exponential distribution, in which the lower-bound u is exactly in line with the evolution of unemployment compensation.

Indonesia is an interesting case study for students of sustainable development and sustainable energy due to its ability to connect the multiple “worlds” it has become part of. Indonesia is an important bridge to Muslim countries, the voice of the Global South in the G20 and a main pillar of the 134-country-strong G77. Indonesia’s development trajectory is also key to the achievement of the Paris Climate Agreement as well as of the 2030 Agenda. Students can learn from how Indo-nesia address contradictions that would have been unsurmountable for other countries. Indone-sia’s energy transition offers helpful lessons, because of its aspiration to become a developed country by 2045. This goal is only possible when a country is able to effectively address barriers and caveats to sustainable energy. It is interesting how Indonesia focuses on silver linings and come up with pragmatic solutions to energy-related issues. This is followed by the “teaching guide,” which provides recommendations how the lessons from Indonesia can be embedded into a learning experience. The “learning activation approach” is introduced, which encourages stu-dents to systematically reflect on the complexity of selected contexts and understand this com-plexity by looking at the technical issues and processes that allow decision-making.

Peer-to-peer (P2P) energy trading is a new data-driven business model currently being trialed within the energy sector. Introducing P2P transactions to an essential service such as energy could have far-reaching implications for individuals and the grid. This paper raises considerations and questions from social, economic/markets and regulatory points of view, that should be understood and addressed by societies and policymakers. It does this by considering under what circumstances it is reasonable to conceptualize P2P energy trading as part of the sharing economy, and drawing parallels to the sharing economy experience in other sectors. In order to reap the full societal benefits, while avoiding considerable risks to infrastructure and individuals, a policy approach promoting dialogue and innovation is necessary. We suggest the regulatory sandbox is the most appropriate tool to achieve this and would help avoid the breakdown of trust between policymakers and platform companies observed in other sectors.

Paraphrase generation is an important yet challenging task in NLP. Neural network-based approaches have achieved remarkable success in sequence-to-sequence(seq2seq) learning. Previous paraphrase generation work generally ignores syntactic information regardless of its availability, with the assumption that neural nets could learn such linguistic knowledge implicitly. In this work we make an endeavor to probe into the efficacy of explicit syntactic information for the task of paraphrase generation. Syntactic information can appear in the form of dependency trees which could be easily acquired from off-the-shelf syntactic parsers. Such tree structures could be conveniently encoded via graph convolutional networks(GCNs) to obtain more meaningful sentence representations, which could improve generated paraphrases. Through extensive experiments on four paraphrase datasets with different sizes and genres, we demonstrate the utility of syntactic information in neural paraphrase generation under the framework of seq2seq modeling. Specifically, our GCN-enhanced models consistently outperform their syntax-agnostic counterparts in multiple evaluation metrics.

Why are pieces of spaghetti generally broken into three to ten segments instead of two as one thinks? How can one obtain the desired number of fracture segments? For these problems, in this paper a strand of spaghetti is considered an elastic rod, and the finite-element software ABAQUS is used to simulate the detailed fracture dynamics of the elastic rod. By changing the size (length and diameter) of the rod, the relevant data on the fracture limit curvature and the number of fractured segments of the elastic rod are obtained. The ABAQUS simulation results confirm the scientific judgment of B. Audoly and S. Neukirch (Fragmentation of rods by cascading cracks: Why spaghetti does not break in half. Phys Rev Lett 95: 095505). Using dimensional analysis to fit the finite-element data, two relations of the elastic rod fracture dynamics are obtained: (1) the relationship between the fracture limit curvature and the diameter, and (2) the relationship between the number of fracture segments and the diameter-length ratio. Results reveal that when the length is constant, the larger the diameter (the smaller the diameter-length ratio D/L), the smaller the limit curvature; and the larger the diameter-length ratio D/L, the fewer the number of fractured segments. The relevant formulations can be used to obtain the desired number of broken segments of spaghetti by changing the diameter-to-length ratio.

1) Background: Intellectual disability is more common in low- and middle-income countries than in high-income countries. Stigma and discrimination have contributed to barriers to people with intellectual disability accessing healthcare. As part of a larger study on caregiving of children with intellectual disability in urban Cape Town, South Africa, we interviewed a sub-group of families who had never used the intellectual disability services available to them, or who had stopped using them; 2) Methods: We employed a qualitative research design and conducted semi-structured interviews to explore the views and perspectives of parents and caregivers of children with intellectual disability who are not using specialised hospital services. We developed an interview guide to help explore caregivers’ and parents’ views; 3) Results: Results revealed that caregivers and parents of children with intellectual disability did not use the service due to financial difficulties, fragile care networks and opportunity costs, community stigma and lack of safety, lack of faith in services and powerlessness at effecting changes, and self-stigmatisation; 4) Conclusion: Current findings highlight a need for increased intervention at community level and collaboration with community-based projects to facilitate access to services, and engagement with broader issues of social exclusion.

Achieving sustainable management of forests in China is becoming increasingly important with more awareness and realization of the importance of forests in environmental protection. Forest certification, a market-based instrument to promote sustainable forest management, has been recognized by many countries including China. While landowners’ perception and perspective regarding this voluntary program have been well-documented in literature, how to motivate and incentivize landowners to participate in forest certification remained under-studied questions. With the face-to-face survey of landowners in Shandong, China, this study analyzed landowners’ willingness to accept compensation for participating in forest certification. Results indicated that landowners average accepted compensation, in terms of increased timber price, was about RMB120 (~$17.2)/m3 to have their forests certified. Results from multiple regression showed that the level of such compensation required for certification adoption was influenced by ownership size, owners’ demographics, certification program requirements, as well as importance placed on timber sale. These findings would inform policy-makers in designing compensation-related polices and establish incentive-based mechanisms to motivate landowners participate in forest certification programs in China.

Despite the long and extensive history of 3D technology, it has recently attracted the attention of researchers. This technology has become the center of interest of young people because of the real feelings and sensations it creates. People see their environment as 3D because of their eye structure. In this study, it is hypothesized that people lose their perception of depth during sleepy moments and that there is a sudden transition from 3D vision to 2D vision. Regarding these transitions, the EEG signal analysis method was used for deep and comprehensive analysis of 2D and 3D brain signals. In this study, a single-stream anaglyph video of random 2D and 3D segments was prepared. After watching this single video, the obtained EEG recordings were considered for two different analyses: the part involving the critical transition (transition-state) and the state analysis of only the 2D versus 3D or 3D versus 2D parts (steady-state). The main objective of this study is to see the behavioral changes of brain signals in 2D and 3D transitions. To clarify the impacts of the human brain’s power spectral density (PSD) in 2D-to-3D (2D_3D) and 3D-to-2D (3D_2D) transitions of anaglyph video, 9 visual healthy individuals were prepared for testing in this pioneering study. Spectrogram graphs based on Short Time Fourier transform (STFT) were considered to evaluate the power spectrum analysis in each EEG channel of transition or steady-state. Thus, in 2D and 3D transition scenarios, important channels representing EEG frequency bands and brain lobes will be identified. To classify the 2D and 3D transitions, the dominant bands and time intervals representing the maximum difference of PSD were selected. Afterward, effective features were selected by applying statistical methods such as standard deviation (SD), maximum (max), and Hjorth parameters to epochs indicating transition intervals. Ultimately, k-Nearest Neighbors (k-NN), Support Vector Machine (SVM), and Linear Discriminant Analysis (LDA) algorithms were applied to classify 2D_3D and 3D_2D transitions. The frontal, temporal, and partially parietal lobes show 2D_3D and 3D_2D transitions with a good classification success rate. Overall, it was found that Hjorth parameters and LDA algorithms have 71.11% and 77.78% classification success rates for transition and steady-state, respectively.

A growing number of households benefit from the government subsidies to install renewable generation facilities such as PV panels, used to gain independence from the grid and provide cheap energy. In the Romanian electricity market, these prosumers can sell their generation surplus only at regulated prices, back to the grid. A way to increase the number of prosumers is to allow them to make higher profit by selling this surplus back into the local network. This would also be an advantage for the consumers, who could pay less for electricity exempt from network tariffs and benefitting from lower prices resulting from the competition between prosumers. One way of enabling this type of trade is to use peer-to-peer contracts traded in local markets, run at microgrid (μG) level. This paper presents a new trading platform based on smart peer-to-peer (P2P) contracts for prosumers energy surplus trading in a real local microgrid. Several trading scenarios are proposed, which give the possibility to perform trading based on participants’ locations, instantaneous active power demand, maximum daily energy demand and the principle of first come first served implemented in an anonymous blockchain trading ledger. The developed scheme is tested on a low-voltage (LV) microgrid model to check its feasibility of deployment in a real network. A comparative analysis between the proposed scenarios, regarding traded quatities and financial benefits is performed.

Background: Alzheimer’s disease (AD), the most threatening neurodegenerative diseases, is characterized by the loss of memory and language function, an unbalanced perception of space and other cognitive and physical manifestations. Pathology of the AD is characterized by neuronal loss, and the extensive distribution of senile plaques and neurofibrillary tangles (NFTs). The role of environment and the diet in the AD is being studied actively, and nutrition is certainly one of the main factors playing a prominent role in the prevention of neurodegenerative diseases. In this context, the relationship between dementia and wine use/abuse has received increased research interest in recent times, with varying and often conflicting results. Scope and approach: This review aims to critically summarize the most recent studies conducted to clarify the relationship between wine drinking and AD, as well as whether effects are influenced by quantity and/or frequency of drinking. Key findings and Conclusion: Overall, based on the interpretation of various studies, it can be concluded that there is no indication that light to moderate alcohol drinking is detrimental to cognition and dementia, and it is not possible to define whether alcohol could be used as a means to reduce risk of developing AD.

The transition towards a renewable energy system is essential in order to reduce greenhouse gas emissions. The increase in the share of variable renewable energy sources (VRES), which mainly comprise wind and solar energy, necessitates storage technologies by which the intermittency of VRES can be compensated for. Although hydrogen has been envisioned to play a significant role as a promising alternative energy carrier in a future European VRES-based energy concept, the optimal design of this system remains uncertain. In this analysis, a hydrogen infrastructure is posited that would meet the electricity and hydrogen demand for a 100% renewable energy-based European energy system in the context of 2050. The overall system design is optimized by minimizing the total annual cost. Onshore and offshore wind energy, open-field photovoltaics (PV), rooftop PV and hydro energy, as well as biomass, are the technologies employed for electricity generation. The electricity generated is then either transmitted through the electrical grid or converted into hydrogen by means of electrolyzers and then distributed through hydrogen pipelines. Battery, hydrogen vessels and salt caverns are considered as potential storage technologies. In the case of a lull, stored hydrogen can be re-electrified to generate electricity to meet demand during that time period. For each location, eligible technologies are introduced, as well as their maximum capacity and hourly demand profiles, in order to build the optimization model. In addition, a generation time series for VRES has been exogenously derived for the model. The generation profiles of wind energy have been investigated in detail by considering future turbine designs with high spatial resolution. In terms of salt cavern storage, the technical potential for hydrogen storage is defined in the system as the maximum allowable capacity per region. Whether or not a technology is installed in a region, the hourly operation of these technologies, as well as the cost of each technology, are obtained within the optimization results. It is revealed that a 100 percent renewable energy system is feasible and would meet both electricity demand and hydrogen demand in Europe.

We propose the traditional goal of cancer therapists to develop a single drug or drug combination that can, by itself, eliminate all cancer cells within a host has neglected potential treatments that may achieve curative outcomes by strategically combining agents that are individually effective but non-curative. We derive basic principles for such an approach from the eco-evolutionary dynamics of background extinctions in which a “first strike” reduces the size and heterogeneity of the initial population and is followed immediately by demographic and ecological “second strikes” that push the population below an extinction threshold. This proposed strategy appears identical to the empirically-derived curative therapy in childhood Acute Lymphocytic Leukemia.

Globally, public acceptance of waste-to-energy (WtE) incinerators is a crucial factor in implementing national waste-to-energy policies. This study adds to the literature on anti-incinerator sentiment by drawing upon an extended psychological-emotional model that integrates place-, trust-, and fairness-based pathways. A total of 338 residents in the Asuwei area in North Beijing completed a survey on a proposal to construct a WtE incinerator in the vicinity. Hierarchical regression analyses indicate that place attachment positively enhances anti-incinerator sentiment through direct effects, as well as through moderation and mediation effects between risk perception and opposing willingness. Further, institutional trust negatively moderates the impact of perceived risk on anti-incinerator sentiment, in addition to directly reducing perceived risk. Trust also influences anti-incinerator sentiment via risk perception, attesting to the effectiveness of a casual model of trust. Likewise, fairness perception acts as another determinant of opposing sentiment, similar to trust. We further reveal that procedural fairness plays a more significant role in predicting anti-incinerator sentiment than does distributional fairness. These findings demonstrate the importance of using a range of instrumental and more affective strategies to promote social acceptance of renewable energy infrastructure.

This paper deals with the techno-economic study of the hybrid renewable energy system based on energy storage aspect under the form of hydrogen and methane. Indeed, with the intermittency of the renewable energy sources such as photovoltaic and wind energy, several problems of produced energy injection to the power system network can be encountered due to the shortage or the excess of these sources. This situation appeals the use of systems that ensure the stability of network based on the storage of energy surplus into gas using electrolyzer systems, which will be used afterward to cover the eventual shortage. In the present paper, the study of performance of each pathway of methane and hydrogen storage has been performed by the treatment of multiple scenarios via different architecture case studies in an Algerian location. Whereas, the energy produced by the photovoltaic system, the wind energy and the gas micro turbine sources are considered similar in each case. The modeling and simulation of the studied system operation under optimization criteria has been performed in this work, where the main aim is to define the appropriate configuration taking into account the different with low costs of investment, maintenance operation and immediate reactivity with a big storage capacity.

Diffusion Models (DMs) are probabilistic models that create realistic samples by simulating the diffusion process, gradually adding and removing noise from data. These models have gained popularity in domains such as image processing, speech synthesis, and natural language processing due to their ability to produce high-quality samples. As DMs are being adopted in various domains, existing literature reviews that often focus on specific areas like computer vision or medical imaging may not serve a broader audience across multiple fields. Therefore, this review presents a comprehensive overview of DMs, covering their theoretical foundations and algorithmic innovations. We highlight their applications in diverse areas such as media quality, authenticity, synthesis, image transformation, healthcare, and more. By consolidating current knowledge and identifying emerging trends, this review aims to facilitate a deeper understanding and broader adoption of DMs and provide guidelines for future researchers and practitioners across diverse disciplines.

Hubei, Hunan and Henan Provinces are located in Central China, a region with extensive transport networks and trade. Bursaphelenchus xylophilus, the causative agent of pine wilt disease, is spreads mainly through human activities. In order to further understand the genetic structure of PWN in Central China, we studied the genetic information of PWN populations in this region and compared the genetic relationship with strains from Guangdong and Jiangsu provinces. We found that the HB (Hubei) 15, HEN (Henan) 20, HN (Hunan) 07, HN08 and HN10 had significantly more SNPs and homozygotes than other strains from Central China, and their most frequent mutant genotypes also differed from other strains. The clustering results indicated that HB15, HEN 20, HN07, HN08 and HN10 were genetically distinct from other strains and closely related to Guangdong strains. We also observed significant genetic variation among strains in Henan province, suggesting that some of them might have different transmission sources than those from Hubei and Hunan provinces. The results provide a basis for tracing the origin and spread of PWD in China.

The salt marshes, lying at the land-sea temperate interface, furnish a plethora of ecosystems services such as biodiversity niche support, ocean-climate change regulation, ornithology recreo-tourism or plant gathering by hand. They undergo significant worldwide losses due to their conversion into crop fields and to their spatial compression between the rising sea-level and the armoring shoreline. Their monitoring however requires to use a suite of remote sensing sensors to embrace the regional scale while capturing the plant details. This research innovatively adopts a multiscale approach using a cascading spaceborne and airborne process, from the 10-m Sentinel-2, through the 3-m Dove, to the 0.03-m unmanned airborne vehicle (UAV) imageries. The high to very high temporal resolution of the Sentinel-2 and Dove enabled to cover twenties and tens of km2 over five and four years, respectively, in the form of normalized difference vegetation index (NDVI) classes, associated with microphytobenthos, low, medium and high salt marsh vegetation, including the opportunistic Elyma genus. The NDVI was then modelled at the UAV scale (a few km2) using a three-layered NN prediction, providing the final near-infrared (NIR), and the intermediate red, green and blue reflectance imageries, calibrated/validated/tested with the Dove reflectance imageries (R2NIR=0.98, R2red=0.88, R2green=0.84, and R2blue=0.90). The 100fold increase in pixel size allowed to detect the decimeter-scale objects of the tidal flats and salt marshes, to enlarge the NDVI class ranges, and hold great promise to model other spectral bands at the UAV scale for further deeply enhancing the salt marsh mapping.

(1) Objective: This study aims to lay a foundation for non-contact intensive care monitoring of premature babies. (2) Methods: Arterial oxygen saturation and heart rate were measured using a monochrome camera and a time division multiplex controlled lightning with three different wavelengths (660 nm, 810 nm and 940 nm) on a piglet model. (3) Results: Using the camera system and our newly designed algorithm for further analysis, the detection of a heartbeat and the calculation of oxygen saturation was evaluated. In motionless individuals, heartbeat and respiration were separated clearly during light breathing and only minor intervention. In this case, the mean difference between non-contact and contact saturation measurements was 0.7% (RMSE = 3.8%, MAE = 2.93%). (4) Conclusions: The new sensor has proven effective under ideal animal experiment conditions. The results allow a systematic improvement for the further development of contactless vital sign monitoring systems. The results presented here are a major step towards the development of an incubator with non-contact sensor systems for use in the neonatal intensive care unit.

Obesity is a major risk factor for the development of life-threatening malignant ventricular tachyarrhythmias (VT) and sudden cardiac death (SCD). Risks may be highest for patients with high levels of the proinflammatory cytokine interleukin (IL)-6. We used our guinea pig model of high-fat diet (HFD) induced Ventricular arrhythmias, that exhibit heightened proinflammatory-like pathology which is also observed in human obesity VT, as well as immunofluorescence, and confocal microscopy approaches to evaluate the pathological IL-6 trans-signaling function and explore the underlying mechanisms. Using blind-stick and electrocardiogram (ECG) techniques, we tested the hypothesis that heightened IL-6 trans-signaling exhibit enhanced Ventricular arrhythmias /SCD incidence and underlying arrhythmia substrates. Remarkably, compared to low-fat (LFD) diet fed controls, HFD promotes phosphorylation of the IL-6 signal transducer and activator of transcription 4 (STAT4) leading to its activation and enhanced nuclear translocation of pSTAT4/STAT4 more than LFD controls and pSTAT3/STAT3 nuclear expression. Overactivation of IL-6 trans-signaling in guinea pigs prolonged the QT interval that resulted in greater susceptibility to VT/SCD with isoproterenol challenge, as also observed with the downstream Janus kinase (JAK) 2 activator. These findings may have potentially profound implications for more effective VT therapy in the vulnerable obese patient population.

This paper experimentally reveals some of the resources offered by the evolution of the instantaneous active electric power in describing the state of three-phase AC induction asynchronous electric motors (with squirrel-cage rotor) operating under no-load conditions. A mechanical power is required to rotate the rotor at no-load and this mechanical power is satisfactorily reflected in the constant and variable part of instantaneous active electric power. The variable part of this electrical power should necessarily have a periodic component with the same period as the period of rotation of the rotor. The paper proposes a procedure for extracting this periodic component description (as a pattern, by means of a selective averaging of instantaneous active electrical power) and analysis. The time origin of this pattern is defined by the time of a selected first passage through the origin of an angular marker placed on the rotor, detectable by a proximity sensor (e.g. a laser sensor). The usefulness of the pattern in describing the state of the motor rotor has been demonstrated by several simple experiments which show that a slight change in the no-load running conditions of the motor (e.g. by placing a dynamically unbalanced mass on the rotor) has clear effects in changing the shape of the pattern.

As cardiovascular diseases continue to be a leading cause of mortality, recent-ly, wearable devices for monitoring cardiac activity have gained much interest among medical community. This paper introduces an innovative ECG monitoring system based on a single – lead ECG machine enhanced with machine learning methods. The system only processes and analyses the ECG data, but also predict potential heart disease at an early stage. The wearable device was built on the ADS1298 and a microcontroller STM32L151xD. A server module based on REST API architecture style was designed to fa-cilitate interaction with web-based segment of the system. The module is responsible for receiving data in real time from microcontroller and their deliver to web – based segment. Algorithms for analyzing ECG signals have been developed, including band filter artifact removal, K-means clustering for signal segmentation, and PQRST analysis. Machine leaning methods as Isolation Forest have been employed for ECG anomaly detection. Moreover, a comparative analysis with various machine learning methods, including lo-gistic regression, random forest, SVM, XGBoost, decision forest and, CNNs was conducted to predict cardiovascular diseases. Convoluted Neural Networks (CNN) showed an accu-racy of 0.926, proving high effectiveness in ECG data process.

This research study focuses on addressing practical optimization challenges in audio-visual content using advanced computational intelligence methods, with a specific emphasis on privacy-preserving issues. The research will be presented as a proposal and can be conducted based on the provided ideas. Computational intelligence encompasses various approaches, including evolutionary algorithms, learning methods, fuzzy systems, and neural networks, which have become essential tools for tackling complex engineering optimization problems due to computational expenses, dimensional complexities, and interdisciplinary integration. The research objectives include a thorough investigation of optimization challenges in audio-visual content, the delineation of problem characteristics, and the development of relevant methodologies based on these specifications. The main goals of the study, titled "Advanced Computational Intelligence Assisted Less-Expensive Privacy-Preserving Optimization," encompass the development of a metamodel-based learning algorithm integrated with evolutionary computation for privacy-preserving optimization, less-expensive signal watermarking optimization using hybrid metamodeling and evolutionary algorithms, and a closed-loop robust intelligent PID control system applied in real-time dynamic signal watermarking. Additional objectives may be defined as the research progresses and further background review is conducted.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

The Food and Drug Administration’s 2011 Process Validation Guidance and International Council for Harmonization Quality Guidelines recommend continued process verification (CPV) as a mandatory requirement for pharmaceutical, biopharmaceutical, and other regulated industries. As a part of product life cycle management, after process characterization in stage 1 and process qualification and validation in stage-2, CPV is performed as stage-3 validation during commercial manufacturing. CPV ensures that the process continues to remain within a validated state. CPV requires the collection and analysis of data related to critical quality attributes, critical material attributes, and critical process parameters on a minimum basis. Data is then used to elucidate process control regarding the capability to meet predefined specifications and stability via statistical process control tools. In statistical process control, control charts and Nelson rules are commonly used throughout the industry to monitor and trend data to ensure that a process remains in control. In the control chart, the mean value is taken as the center line, and 3σ limits are placed on either side of the center line. In CPV, manufactured lots are summarized, trended, and discussed at a cross-functional level at pre-defined intervals (either weekly, bi-weekly, or even monthly) based on the batch run rate. A cross-functional team assesses details regarding 1) violation frequency, 2) statistical strength of the signal, 3) violation magnitude and its impact on process or quality, and 4) any potential root causes for out-of-expectation or out-of-trend signals. The cross-functional team must analyze whether any signal identified by the control chart is reliable and must determine whether corrective action should be taken and justify the decision in the CPV meeting minutes based on statistical strength and reliability of the signal. However, basic control charts are susceptible to false alarms and nuisance alarms. Therefore, it is imperative to understand the assumptions behind control charts and the inherent false alarm rates for different Nelson rules. In this article, the authors have detailed the assumptions behind the usage of control charts, the rate of false alarms for different Nelson rules, the impact of skewness and kurtosis of a data distribution on the false alarm rate, and methods for optimizing control chart design by reducing false alarm rates and nuisance signals.

Surface roughness prediction is a pivotal aspect of the manufacturing industry, as it directly influences product quality and process optimization. This study introduces a predictive model for surface roughness in the turning of complex-structured workpieces, utilizing Gaussian Process Regression (GPR) informed by vibration signals. The model captures parameters from both the time and frequency domains of the turning tool, encompassing the mean, median, standard deviation (STD), and root mean square (RMS) values. The signal is from the time to frequency domain is executed using Welch's method, complemented by time-frequency domain analysis employing three levels of Daubechies Wavelet Packet Transform (WPT). The selected features are then utilized as inputs for the GPR model to forecast surface roughness. Empirical evidence indicates that the GPR model can accurately predict the surface roughness of turned complex-structured workpieces. This predictive strategy has the potential to improve product quality, streamline manufacturing processes, and minimize waste within the industry.

Detecting gear rim fatigue cracks using vibration signal analysis is often a challenging task, which typically requires a series of signal processing steps to detect and enhance fault features. This task becomes even harder in helicopter planetary gearboxes due to the complex interactions between different gear sets, and the presence of vibration from sources other than the planetary gear set. In this paper, we propose an effectual processing algorithm to isolate and enhance rim crack features and to trend crack growth in planet gears. The algorithm is based on using cepstrum editing (or liftering) of the hunting tooth synchronous averaged signals (angular domain) to extract harmonics and sidebands of the planet gears, and low-pass filtering and minimum entropy deconvolution (MED) to enhance extracted fault features. The algorithm has been successfully applied to a vibration dataset collected from a planet gear rim crack propagation test undertaken in the Helicopter Transmission Test Facility (HTTF) at DSTG Melbourne. In this test, a seeded notch generated by an electric discharge machine (EDM) was used to initiate a fatigue crack that propagated through the gear rim body over 94 load cycles. The proposed algorithm demonstrated a successful isolation of incipient fault features and provided a reliable trending capability to monitor crack progression. Results of a comparative analysis showed that the proposed algorithm outperformed the traditional signal processing approach.

In arXiv:2111.15017v1 [1], Dias and Salamat posted some of the measured data for ac magnetic susceptibility of carbonaceous sulfur hydride, a material that was reported in Nature 586, 373 (2020) [2] to be a room temperature superconductor. They provided additional measured data in arXiv:2111.15017v2 [3]. Here I provide an analysis of these data. The results of this analysis indicate that the claim of ref. [2] that magnetic susceptibility measurements support the conclusion that the material is a room temperature superconductor is not supported by valid underlying data.

Over the past few years, the importance of video surveillance in securing the national critical infrastructure has significantly increased, whose applications include detecting failures and anomalies. Accompanied by video proliferation is the increasing number of attacks against surveillance systems. Among the attacks, false frame injection (FFI) attacks that replay video frames from a previous recording to mask the live feed has the highest impact. While many attempts have been made to detect FFI frames using features from the video feeds, video analysis is computationally too intensive to be deployed on-site for real-time false frame detection. In this paper, we investigate the feasibility of FFI attacks on compromised surveillance systems at the edge and propose an effective technique to detect the injected false video and audio frames by monitoring the surveillance feed using the embedded Electrical Network Frequency (ENF) signals. An ENF operates at a nominal frequency of 60 Hz/50 Hz based on its geographical location and maintains a stable value across the entire power grid interconnection with minor fluctuations. For surveillance system video/audio recordings connected to the power grid, the ENF signals are embedded. The time-varying nature of the ENF component is used as a forensic application for authenticating the surveillance feed. The paper highlights the ENF signal collection from a power grid creating a reference database and ENF extraction from the recordings using conventional short-time Fourier Transform and spectrum detection for robust ENF signal analysis in the presence of noise and interference caused in different harmonics. The experimental results demonstrate the effectiveness of ENF signal detection and/or abnormalities for FFI attacks.

The detection of seismic events at regional and teleseismic distances is critical to Nuclear Treaty Monitoring. Traditionally, detecting regional and teleseismic events has required the use of an expensive multi-instrument seismic array; however in this work, we present DeepPick, a novel seismic detection algorithm capable of array-like performance from a single trace. We achieve this directly, by training our single-trace detector against labeled events from an array catalog, and by utilizing a deep temporal convolutional neural network. The training data consists of all arrivals in the International Seismological Centre Catalog for seven seismic arrays over a five year window from 1 Jan 2010 to 1 Jan 2015, yielding a total training set of 608,362 detections. The test set consists of the same seven arrays over a one year window from 1 Jan 2015 to 1 Jan 2016. We report our results by training the algorithm on six of the arrays and testing it on the seventh, so as to demonstrate the transportability and generalization of the technique to new stations. Detection performance against this test set is outstanding. Fixing a type-I error rate of 1%, the algorithm achieves an overall recall rate of 73% on the 141,095 array beam picks in the test set, yielding 102,394 correct detections. This is more than 4 times the 23,259 detections found in the analyst-reviewed single-trace catalogs over the same period, and represents an 8dB improvement in detector sensitivity over current methods. These results demonstrate the potential of our algorithm to significantly enhance the effectiveness of the global treaty monitoring network.

This paper presents the design and implementation of a digital control system for modular multilevel converters (MMC) and its use in a 5-kW small scale prototype. To achieve higher system control reliability and multi-functionality, the proposed architecture has been built with an effective split of the control tasks between a master controller and six slave controllers, one for each of the six arms of the converter. The MMC prototype have been used for testing both converter and system level controls in a reduced scale laboratory set up of a Multi-Terminal DC transmission network (MTDC). The whole control has been tested in order to validate the proposed control strategies. The tests performed at system level allowed to explore the advantages of using an MMC in a MTDC system.

Pigment dispersion can lead to pigmentary glaucoma, a poorly understood condition of younger myopic eyes with fluctuating high intraocular pressure. It has been difficult to investigate its pathogenesis without a model similar to human eyes in size and behavior. Here we present a porcine ex vivo model that recreates several features of pigmentary glaucoma, including intraocular hypertension, accumulation of pigment in the trabecular meshwork, and declining phagocytosis. We found that trabecular meshwork cells regulate outflow, form actin stress fibers, and have a decreased phagocytic activity. Gene expression microarrays and a pathway analysis of TM monolayers as well as ex vivo anterior segment perfusion cultures indicated that RhoA plays a central role in regulating the cytoskeleton, motility, and phagocytosis in the trabecular meshwork, providing new insights and targets to investigate in pigmentary glaucoma.

The mitigation of NLOS (non-line-of-sight) propagation conditions is one of main challenges in wireless signals based indoor localization. When RFID localization technology is applied in applications, RSS fluctuates frequently due to the shade and multipath effect of RF signal, which could result in localization inaccuracy. In particularly, when tags carriers are walking in LOS (line-of-sight) and NLOS hybrid environment, great attenuation of RSS will happen, which would result in great location deviation. The paper proposes an IMU-assisted (Inertial Measurement Unit) RFID based indoor localization in LOS/NLOS hybrid environment. The proposed method includes three improvements over previous RSS based positioning methods: IMU aided RSS filtering, IMU aided LOS/NLOS distinguishing and IMU aided LOS/NLOS environment switching. Also, CRLB (Cramér-Rao Low Bound) is calculated to prove theoretically that indoor positioning accuracy for proposed method in LOS/NLOS mixed environment is higher than position precision of only use RSS information. Simulation and experiments are conducted to show that proposed method can reduce the mean positioning error to around 3 meters without site survey.

Indoor positioning based on the received signal strength (RSS) of the WiFi signal has become the most popular solution for indoor localization. In order to realize the rapid deployment of indoor localization systems, solutions based on crowdsourcing have been proposed. However, compared to conventional methods, crowdsourced RSS values are more erroneous and can result in large localization errors. To mitigate the negative effect of the erroneous measurements, a graph-based semi-supervised learning (G-SSL) method is used to exploit the correlation between the RSS values at nearby locations to estimate an optimal RSS value at each location. Before using the G-SSL method, the Linear Regression (LR) algorithm is proposed to solve the device diversity problem in crowdsourcing system. Since the spatial distribution of the APs is sparse, the Compressed Sensing (CS) method is applied to precisely estimate the location of the APs. Based on the location of the APs and a simple signal propagation model, the RSS difference between different locations is calculated and used as an additional constraint to improve the performance of G-SSL. Furthermore, to exploit the sparsity of the weights used in the G-SSL, we use the CS method to reconstruct these weights more accurately and make a further improvement on the performance of the G-SSL. Experimental results show improved results in terms of the smoothness of the radio map and the localization accuracy.

Acute high altitude illnesses are of great concern for physicians and people traveling to high altitude. High Altitude Pulmonary Edema (HAPE) can be better understood through the Oxygen Transport Triad which involves the Pneumo-Dynamic Pump (Ventilation), the Hemo-Dynamic Pump (Heart and circulation), and Hemoglobin. The two pumps are the first physiologic response upon initial exposure to hypobaric hypoxia. Hemoglobin is the balancing energy-saving time-evolving equilibrating factor. The increased hemoglobin at high altitude reduces the percentage of dissolved oxygen in the arterial oxygen content with respect to sea level. At high altitude, the acid-base balance must be adequately interpreted using the high altitude Van-Slyke correction factors. Pulse-oximetry measurements during breath-holding at high altitude allow for the evaluation of high altitude diseases. The Tolerance to Hypoxia Formula shows that, paradoxically, the higher the altitude the more tolerance to hypoxia. All organisms adapt physiologically and optimally to a high-altitude environment to survive. Reduction of pulmonary hypertension in HAPE through oxygen administration results in a favorable outcome.

The research is devoted to the problem of noise generation during flights of supersonic civil aircrafts. The effect of a thermally stratified energy source used to control the flow past a pointed cylinder aerodynamic models on the nearfield and ground pressure signatures, as well as on the perceived loudness in decibels (PLdB) on the ground is evaluated. The fields of parameters and the dynamics of the drag forces are studied for different values of temperature in the layers of the thermally stratified energy source and for different number of layers in it. It has been shown that when performing the flow control at freestream Mach numbers 1.5-2 using thermally stratified energy sources with the number of layers from 2.5 to 7.5 and rarefaction parameters in the layers from 0.15 to 0.3, no additional noise impact on the ground is introduced. Thus, the simulations showed that changing the surface pressure signature due to drag reduction does not necessarily imply a change in the PLdB on the ground.

Water treatment is one of the most research-challenging areas, and continuously requires the development of efficient sustainable materials for catalytic total mineralization of organic compounds. Herein, Moringa oleifera biomass was converted to "black gold" biochar loaded with ZnO nanoparticles (MOFB@ZnO) by slow pyrolysis, at 500 °C under an inert atmosphere, (MOFB@ZnO). This composite catalyst was used for the total degradation of Congo Red, a model organic pollutant. SEM confirmed the uniform distribution of ZnO nanoparticles, while XPS and XRD indicated the presence of ZnO, primarily in the wurtzite crystalline structure. Optimization was conducted using the central composite design (CCD) method and STATISTICA 12.0 software. The composite catalyst was applied in the electrochemical degradation of Congo Red dye, using a platinum anode and a carbon felt cathode to generate H2O2 from O2 reduction. The ZnO-decorated Moringa oleifera biochar catalyst permitted to achieve of 98% removal of total organic carbon in less than 6h. It is 10-fold more efficient than pristine biochar and can be recycled up to 4 times without any significant loss. The process is highly efficient producing sustainable low-cost catalysts for water purification from organics, and contributes to sustainable chemical processes therefore addressing SDGs 6, 9, and 13.

The purpose of this study was to investigate the effects of cognitive dual-tasking on gait initiation and sit-to-walk. Twenty-eight healthy young adults performed gait initiation and sit-to-walk under two conditions: while engaging in serial subtraction (dual-task) and without any additional task (single-task). Motion data were collected using a 10-camera optoelectronic motion capture system, synchronized with force plates and surface electromyography. We analyzed spatiotemporal parameters, center of mass displacement, center of pressure trajectory, and lower limb muscle activation patterns. We found that dual-task conditions significantly affected both gait initiation and sit-to-walk patterns, increasing the duration of transitions and mediolateral center of mass displacements, while reducing vertical center of mass displacements and forward propulsion. We also observed a more constrained and less efficient center of pressure path, with reduced posterior displacement during the weight shift phase. Muscle activation, particularly in the tibialis anterior and biceps femoris, decreased during dual-task conditions, indicating altered neuromuscular strategies. These findings suggest a shift in postural control demands and motor performance during dual-task transitions.

This paper presents a comprehensive study on the design and aerodynamic optimization of a hybrid surveillance drone, conducted within the academic framework of Abu Dhabi University. The research primarily focuses on the comparison between flying wing and conventional aircraft layouts, with an emphasis on reducing drag coefficients and enhancing stall behavior through integrated design strategies. Utilizing SST k-omega viscous model (CFD) simulations, the study evaluates the aerodynamic performance of the drone model, analyzing lift, drag, and pitching moment coefficients against existing models. The paper further explores winglet selection and propeller dynamics, aiming to optimize the lift-to-drag ratio and achieve desired lift-to-weight ratios through careful consideration of propeller-wing interactions. Findings from the study indicate a notable improvement in aerodynamic efficiency, with the new drone model achieving a maximum lift coefficient (Cl, max) of 0.746, a minimum drag coefficient (Cd, min) of 0.039, and a peak lift-to-drag ratio (Cl/Cd) of 8.507. The research contributes significantly to the fields of Aerospace Engineering and Mechanical Engineering, providing a foundation for future advancements in drone design and application.

Visual servoing technology has been well developed and applied in many automated manufacturing tasks, especially in tools’ pose alignment. To access a full global view of tools, most applications adopt eye-to-hand configuration or eye-to-hand/eye-in-hand cooperation configura-tion in an automated manufacturing environment. All research papers mainly put efforts into developing control and observation architectures in various scenarios, but none of them has dis-cussed the importance of the camera’s location in eye-to-hand configuration. In a manufacturing environment, the quality of camera estimations may vary significantly from one observation loca-tion to another, as the combined effects of environmental conditions result in different noise levels of a single image shot at different locations. In this paper, we propose an algorithm for the camera’s moving policy so that it explores the camera workspace and searches for the optimal location where the images’ noise level is minimized. Also, this algorithm ensures the camera ends up at a subop-timal (if the optimal one is unreachable) location among the locations already searched, with limited energy available for moving the camera. An automated manufacturing application has been sim-ulated and the results show the success of this algorithm’s improvement of observation precision with limited energy.

Smart agriculture is a new way of farming that uses advanced technology. It makes a significant contribution to improving the efficiency and productivity of farming practices. Systems that use drones to monitor pests and spray pesticides greatly reduce the burden on farmers. In addition, remote sensing technology facilitates the monitoring of crop growth conditions and the early detection of diseases and pests. However, the high cost of equipment to communicate sensor data is preventing farmers from adopting sensing systems. As a result, many studies have been conducted to make the sensing system available at a low cost. Nevertheless, many farmers have not yet adopted them. Therefore, this paper proposes an agricultural sensor network system using drones and optical camera communication (OCC). The proposed system aims to achieve high-density farm sensing at low cost. The proposed system uses OCC as the communication method for sensor data. Low cost light sources such as LED panels can be used as transmitters. In addition, existing agricultural drones equipped with cameras can be used as receivers. We also propose a trajectory control algorithm for the receiving drone to efficiently collect the sensor data. The proposed system is suitable for deploying sensor networks in areas with underdeveloped infrastructure and radio silence. In this paper, we conducted a preliminary experiment at a leaf mustard farm in Kamitonda-cho, Wakayama to demonstrate the effectiveness of the proposed system using a Mavic 2 Pro drone, launched by DJI Co., Ltd.

In this study, it was analyzed that the characteristics of ammonia and their effects on secondary particulate matter (PM) formation by region in Korea during 2020. The NH3 concentration was high in GJ (11.4 ppb) neighboring agricultural area followed by DJ (9.0 ppb) and SE (8.6 ppb) locating in the urban area. On the other hand, BI (2.6 ppb) and JI (4.5 ppb), which are background regions, were lower than other area. Seasonally, ammonia was high in spring and summer, and it generally increased when human activities are active. Therefore, it is believed that ammonia in the atmosphere changes depending on not only local emissions but also temperature-dependent phase distribution characteristics. For SE and GJ, regions with relatively high ammonia concentrations, the effect of ammonia on secondary PM formation was conducted. In both regions, the ammonium-to-sulfate mole ratio tended to increase with an ammonia or PM2.5 concentration increasing. It can be assumed that PM2.5 concentration increases as nitrates are formed under the ammonia sufficient condition. The adjusted gas ratio is generally greater than 4, indicating that there is a lot of free ammonia. Thus, it is estimated that reduction of ammonia would not effective to restrain the nitrate formation.

This paper explores the critical role of the banking sector in facilitating the ecological transition through the integration of ESG (Environmental, Social, and Governance) factors. By analyzing the intersection of ESG considerations and access to credit globally, the study highlights how banks can catalyze sustainable investments while balancing financial risks. Using a systematic literature review and k-Means clustering analysis, we assess the global landscape of credit access, emphasizing the implications of ESG adoption on financial stability and economic growth. The findings suggest that while ESG integration presents challenges, it offers significant opportunities for banks to enhance their competitiveness and foster resilient financial systems. The paper concludes by proposing policy recommendations aimed at improving the incorporation of ESG factors within credit risk management and promoting sustainable finance.

(1) Background: São Paulo, Brazil, exhibits high mortality rates from pediatric solid tumors. This study analyzed the survival trends of patients aged 0-19 diagnosed with the state's five most prevalent solid tumors between 2000-2022. (2) Methods: An epidemiological, descriptive study utilized data from the Oncocentro Foundation of São Paulo, classified according to the International Classification of Childhood Cancer. The time between the first consultation and diagnosis, between diagnosis and treatment initiation, and patient survival were assessed using the Pe-to-Peto test. (3) Results: Analysis involved 11,067 cases: 53.5% male, with 89.6% diagnosed via microscopic confirmation. Tumor distribution comprised 34.3% central nervous system, 21.1% bone, 18.6% soft tissue, 14.2% germ cell, and 11.9% retinoblastomas. Main treatments included surgery with chemotherapy (26.5%), surgery alone (20.5%), and chemotherapy alone (15.6%). The average time between consultation and diagnosis was 22.94 ± 69.93 days, significant for treatments and recurrences, except for germ cell tumors (p=0.0178). The time between diagnosis and treatment was 25.46 ± 39.71 days, not significant for germ cell tumor treatments (p=0.0793). (4) Conclusions: Survival curves varied among neoplasm groups, with patients experiencing delays beyond recommended times, despite advanced healthcare services in the state.

The theory of limited numbers says that the number is not infinite, that is, the number is limited in parts or completely. To reach a conclusion about the limited number, one must understand the meaning of mathematics and varied spaces, therefore, one must understand that mathematics and spaces interact. Mathematics has the function of describing the world precisely, where numbers represent elements or facts that rationally belong to space, and spaces have different intensities of specific physical concepts in each space; therefore, there is no infinite element or fact due to differences in the intensities of specific physical concepts in spaces that do not allow for the fact or fact in all spaces.

Parkinson’s disease (PD) is the second most common degenerative disease which may cause blood pressure abnormalities due to autonomic dysfunction. Early morning rise of blood pressure which is called morning surge is found to be related with some cardiovascular diseases when it is exaggerated. We wanted to search the relation of Morning blood pressure surge (MBPS) and inflammation in PD. Method: Ambulatory blood pressure monitoring for 24 hours, fibrinogen to albumin ratio, hs-CRP are used in this retrospective study. Fifty idiopathic PD patients and 50 age and sex matched control cases were included. MBPS, it has been defined as the difference between morning BP (measured 2 hours after awakening) and the lowest night-time BP. Body mass index (BMI) is used as an independent variable. Results: Median value of MBPS for PD group (21,63) was significantly different from the control group values (18,63) (p

Green and low-carbon development has become an important embodiment of China's path to becoming a strong agricultural country. How to enable agricultural enterprises to better adopt green technologies and conduct production and operation with the concept of sustainable development has become a key link. This article utilizes a structural equation model (SEM) to analyze the role paths and mediating effects of organizational learning ability and policy orientation in agricultural enterprises' market orientation and willingness to adopt green technologies[ The definition of green technology in this paper refers to Guo Kesha, Tian Xiaoxiao. Green technology and green transformation of industrial development mode [J]. Tianjin Social Sciences, 2024 (02) :99-107, including green manufacturing (production) technology and green service technology.]. The results show that market orientation, organizational learning ability, and policy effectiveness have significant direct positive impacts on the willingness to adopt; market orientation has a significant positive impact on agricultural enterprises' organizational learning ability, organizational learning ability has a significant positive impact on policy orientation, and market orientation has a significant positive impact on policy effectiveness; the results of mediation analysis also indicate that learning ability has a significant mediating effect between market orientation and willingness to adopt, and policy effectiveness has a significant mediating effect between market orientation and willingness to adopt. Through difference analysis, it is believed that the mediating effects of the three paths are equally important, and organizational learning ability and policy effectiveness play a partial mediating role in agricultural enterprises' willingness to adopt green technologies. Based on this, policy suggestions are proposed to improve enterprises' own organizational learning ability, increase the promotion of policies related to green technologies, improve relevant policies for the application of green technologies, and increase research and development efforts for green technologies.

To reduce the redundant counting of TDC in high-speed applications and thus reduce power consumption, a TDC architecture is proposed to quantify the difference between two adjacent rows of pixel signals. This structure can remove the identical part between two rows of pixel signals by adjusting the start and stop signal of the TDC, which will reduce the number of flipping of D flip-flops in the TDC. In the 110nm CMOS process, simulation results show that this design achieves an effective number of bits (ENOB) of 4.72 bits and a Figure of Merit (FoM) of 104.7 fJ/step - 162.3 fJ/step with a power consumption ranging from 60 µW to 93 µW. Compared with traditional counting methods, the proposed TDC can reduce counting power consumption by 30%.

The benefits of cycling as a sustainable transportation mode are widely recognized. Cycling to work offers numerous advantages for individuals, employers, the environment, and society, ranging from improved physical health, wellbeing, and productivity to enhanced public health and reduced carbon emissions. Many governments around the world have implemented various policy measures, interventions, and initiatives to promote cycling. Some cities and towns have encouraged workplaces to provide bike-friendly amenities, such as secure bike parking/storage and shower and changing facility (referred to as end-of-trip facilities), to accommodate cyclists and motivate more employees to embrace sustainable transportation options. However, the presence or absence of such amenities has been found to both positively influence cycling behavior or deter some individuals from cycling to work. Despite the desirability of these amenities, the number of office buildings equipped with bike storage and shower/changing facility remains small, and their economic value is not well understood. In this paper, we aim to investigate whether the presence of cycling-supportive facilities could add value to office buildings. Specifically, we conduct a study using data from office buildings across England as of the end of 2021. We employ hedonic techniques to examine whether office buildings with bike storage and/or shower facility command a rent premium and whether the existence of a rent premium for bike storage and/or shower facility vary by location and across regions in England, independently from any premium associated with BREEM certification. We find that the buildings with bike storage and shower facility secure rent premiums respectively. The level of rent premiums varies with location and regions. The variations of premium are driven by the shortage of the supply of these facilities.

The aim of the research was to determine the most productive tree cutting methods and the factors influencing them in flat and sloping terrain in tree plantations in Brazil. The study utilized drone-captured video material from eucalyptus and pine plantations harvesting operations. In both terrains, two cutting methods were compared, differing in the felling to the side method used: either at the edge of the harvesting front or inside. In addition, on flat terrain, the efficiency of forward felling was studied in relation to the aforementioned methods. In slope terrain, the machines were also equipped with a winch assistance system. Statistical tests were used to determine the most productive cutting methods by analyzing differences in productivity. With an average tree size of 0.3 m3, cutting productivity was 45 m3/E0h in pine cuttings and 55 m3/E0h in eucalyptus cuttings. The average cutting productivity on flat terrain was about 11 m3/E0h higher than on sloping terrain, mainly due to the time spent attaching the winch assistance system, which was a necessary phase of the work in sloping terrain. The research results suggest that it would be the most productive to use sideways felling inside the harvesting front method. However, the need for further research is evident if we want to precisely identify the harvesting conditions and work phases in the tree cutting cycle affecting the differences in the productivity of the harvesting chain in tree plantations.

The paper proposes a methodological way to compensate the imbalance between energy generation and consumption using the battery block of electric vehicles as energy reservoir through the well-known Vehicle to Grid system (V2G). The method is based on a simulation process developed by the authors that take into consideration the daily fluctuations of energy consumption as well as the power level generated by an energy source, either conventional, renewable or hybrid. The study shows that for very large electric vehicle fleet the system renders non-viable, since the remaining energy in the battery block to let the electric vehicle usable for running during daytime avoids to compensating for the energy grid imbalance, only allowing to cover a percentage of the energy imbalance, which the proposed methodology may optimize. The analysis of the proposed methodology also shows the viability of the system when being applied to a small fleet of electric vehicles, not only compensating for the energy imbalance but also preserving the required energy in the battery of the electric vehicle to make it run. The method allows predicting the optimum size of electric vehicle battery, which depends on the energy generation level, coverage factor of the energy imbalance and size of the electric vehicle fleet.

Commercial buildings situated in hot and humid tropical climates rely significantly on cooling systems to maintain optimal occupant comfort. A well-accurate day-ahead load profile prediction plays a pivotal role in planning the energy requirements of cooling systems. Despite the pressing need for effective day-ahead cooling load predictions, current methodologies have not fully harnessed the potential of advanced deep-learning techniques. This research paper aims to address this gap by investigating the application of innovative deep learning models in day-ahead hourly cooling load prediction for commercial buildings situated in tropical climates. A range of deep learning techniques, including Deep Neural Network, Convolutional Neural Networks, Recurrent Neural Networks, and Long Short-Term Memory networks are employed to enhance prediction accuracy. Furthermore, these individual deep learning techniques are synergistically integrated to create hybrid models, such as CNN-LSTM and Sequence-to-Sequence models. An extensive comparative analysis is conducted to identify the most effective hybrid model. Sequence-to-sequence model provided better performance compared to the other single and hybrid models. Experiments are conducted to choose the time horizons from the past that can serve as input to the models. Further, the influence of various categories of input parameters on prediction performance has been assessed. Historical cooling load, calendar features and outdoor weather parameters are found in decreasing order of influence on prediction accuracy. This research focuses on buildings located in Singapore and presents a comprehensive case study to validate the proposed models and methodologies.

Pedestrians, bicyclists, scooterists are Vulnerable Road Users (VRU) in traffic accidents. The number of fatalities and injuries in traffic accidents involving vulnerable road users has been steadily increasing in the last two decades in the U.S. even though road vehicles now have perception sensors like camera to detect risk and issue collision warnings or apply emergency braking. Perception sensors like camera are highly affected by lighting and weather conditions. Camera, radar and lidar cannot detect vulnerable road users in partially occluded and occluded situations. This paper proposes the use of Vehicle-to-VRU communication to inform nearby vehicles of VRUs having trajectories with potential collision risk. An Android smartphone app with low energy Bluetooth (BLE) advertising is developed and used for this communication. The same app is also used to collect motion data of VRUs for training. VRU motion data is smoothed using a Kalman filter and an LSTM neural network is used for future motion prediction. This information is used in an algorithm comparing Time-To-collision-Zone (TTZ) for the vehicle and VRU and issue a driver warning with different severity levels. The warning severity level is based on analysis of real data from a smart intersection for close vehicle and VRU interactions. The resulting driver warning system is demonstrated using proof-of-concept experiments. The method can easily be extended to a VRU collision mitigation system.

A significant amount of data is available for bench-scale fire assessments. However, there is little surrounding large-scale tests and even less so for bench-to-large scale comparisons. Large-scale tests require more material, time and preparation, making them more expensive than bench-scale assessments. However, large-scale testing is an essential component to bench-scale fire testing. The bench-scale tests must be representative of both large-scale and real fire behaviour to provide an insight into how a material or product will behave in the event of a fire during its end use application. The few existing studies reviewed in this study show more guidance and data is needed, especially on a large-scale. Unfortunately, the data that is presented is done so in an inconsistent manner using various means of presentation, statistical analysis, and modelling that doesn’t show clear comparisons between bench and large scale. Currently, no bench-scale method shows good agreement with large-scale fire behaviour. Overall, there is a need for more large-scale testing and data for direct comparisons to be made.

Background and Objectives: The severity of acute pancreatitis (AP) is graded as mild (MAP), moderately severe (MSAP), and severe (SAP) according to the revised Atlanta Classification. Determining the severity of AP is the main goal in the early time of AP. The aim of this study was to compare laboratory parameters or indices including neutrophil-to-lymphocyte ratio (NLR), platelet-to-lymphocyte ratio (PLR) and neutrophil-creatinine index (NCI) at admission for predicting severity of AP. Materials and Methods: In this retrospective study, the data from patients who admitted with diagnosis of AP between January 2018 and December 2021 were collected. Laboratory parameters and indices including NLR, PLR and NCI were compared in the discrimination of AP severity groups. Results: A total of 421 patients [MAP group (n=213), MSAP group (n=158) and SAP group (n=50)] were included. WBC count, neutrophil count, hematocrit, CRP, BUN, creatinine, NLR and NCI were significant parameters to discriminate AP subgroups. The AUROC analysis for discriminating MSAP from MAP showed that WBC (AUC: 0.723, 95% CI: 0.674-0.768, p&lt;0.001), hematocrit (AUC: 0.566, 95% CI: 0.514-0.607, p=0.032), NLR (AUC: 0.649, 95% CI: 0.598-0.698, p&lt; 0.001) and NCI (AUC: 0.749, 95% CI: 0.701-0.792, p&lt;0.001) were statistically significant parameters. Similarly, AUCs to discriminate SAP from MSAP were (AUC: 0.649, 95% CI: 0.579-0.713, p &lt; 0.001) for WBC, (AUC: 0.703, 95% CI: 0.621-0.785, p&lt; 0.001) for BUN, (AUC: 0.602, 95% CI: 0.532-0.669, p=0.029) for CRP and (AUC: 0.742, 95% CI: 0.676-0.800, p&lt;0.001) for NCI. Logistic regression analyses indicated that NCI was the only parameter to discriminate MSAP form MAP (OR: 1.119, 95% CI: 1.015-1.235, p=0.023) and SAP from MSAP (OR: 1.113, 95% CI: 1.042-1.888, p = 0.001). Conclusions: The present study enabled the identification of neutrophil-creatinine index as a new prognostic tool for the assessment AP severity at hospital admission.

The current study primarily aimed to simulate detonation initiation via turbulent jet flame acceleration in partial-premixed H2-air mixtures. Different vertical concentration gradients were generated by varying the duration of hydrogen injection (referred to as diffusion time) within an enclosed channel filled with air. H2-air mixtures with average hydrogen concentrations of 22.5% (lean mixture) and 30% (near stoichiometric mixture) were investigated at diffusion times of 3, 5, and 60 seconds. Numerical results show that the vertical concentration gradient has a major influence on the early-stage of flame acceleration (FA). In the stratified lean mixture, detonation began in all the diffusion times, and comparing the flame-speed graphs showed that a decrease in the diffusion time and an increase in the mixture inhomogeneity speeded up the flame propagation and the jet flame to detonation transition occurrence in the channel. In the stratified H2-air mixture with an average hydrogen concentration of 30%, transition from a turbulent jet flame to detonation occurred in all the cases, and the mixture inhomogeneity weakened the FA and delayed the detonation initiation.

Liver transplantation is currently the only curative therapy for patients with liver cirrhosis. Not all patients in the natural course of the disease will undergo transplantation, but the majority of them will experience portal hypertension and its complications. In addition to medical and endoscopic therapy, a key role in managing these complications is played by the placement of a transjugular intrahepatic portosystemic shunt (TIPS). Some indications for TIPS placement are well-established and they are expanding and broadening over time. This review aims to describe the role of TIPS in managing patients with liver cirrhosis, considering them as potential candidates for liver transplantation. As far as is known TIPS placement seems not to affect the surgical aspects of liver transplantation, in terms of intra operative bleeding rates, postoperative complications or length of stay in the Intensive Care Unit. However, the placement of a TIPS “towards transplant" can offer advantages in terms of enhancing the patient's clinical condition at the time of transplantation and improving patient survival. Additionally, the TIPS procedure can help preserve the technical feasibility of the transplant itself. In this context, indications for TIPS placement may be expanded and considered at an earlier stage. TIPS insertion can also lead to serious adverse events and there are no evidence-based recommendations on this topic to date. For these reasons further studies are needed to make reliable recommendations for TIPS in the pre-transplant setting.

Molnupiravir, a prodrug known for its broad antiviral activity, demonstrated efficacy in animal models of Covid-19, prompting clinical trials where initial results indicated a significant effect against the disease. However, subsequent clinical studies did not confirm these findings, leading to the rejection of molnupiravir for permanent market authorization in many countries. This report critically assessed 19 studies published in 17 reports that investigated the efficacy of molnupiravir in animal models of Covid-19 with the purpose of determining how well the design of these models informed human studies. We found that the administered doses of molnupiravir in most studies involving animal Covid-19 models were disproportionately higher than the dose rec-ommended for human use. Specifically, when adjusted for body surface area, half of the doses of molnupiravir used in the animal studies were more than twice as high as the human dose. Addi-tionally, the drug was frequently given prophylactically or shortly after SARS-CoV-2 inoculation in these models, in contrast to clinical trials where such timing is not consistently achieved. Furthermore, the recommended five-day treatment duration for humans was exceeded in several animal studies. Collectively, we suggest that these design elements in the reported animal studies contributed to a bias favoring molnupiravir, and thus inflated expectations for its efficacy against Covid-19. Addressing these elements may offer avenues to enhance the clinical efficacy of mol-nupiravir for treatment of Covid-19 that include dose increment, early treatment, and admin-istration by inhalation along with use of molnupiravir in antiviral combination therapy.

This paper introduces an advanced method that integrates contingent valuation and machine learning (CVML) to estimate residents’ demand for reducing or mitigating environmental pollutions and climate change. To be precise, CVML is an innovative hybrid machine-learning model, and it can leverage a limited amount of survey data for prediction and data enrichment purposes. The model comprises of two interconnected modules: Module I, an unsupervised learning algorithm, and Module II, a supervised learning algorithm. Module I is responsible for grouping the data into groups based on common characteristics, thereby grouping the corresponding dependent variable, whereas Module II is in charge of demonstrating the ability to predict and the capacity to appropriately assign new samples to their respective category based on input attributes. Take a survey on the topic of air pollution in Hanoi in 2019 as an example, we found that CVML can predict households’ willingness– to– pay for polluted air mitigation at a high degree of accuracy (i.e., 98%). We found that CVML can help users reduce costs or save resources because it makes use of secondary data that is available on many open data sources. These findings suggest that CVML is a sound and practical method that could be widely applied in a wide range of fields, particularly environmental economics and sustainability science. In practice, CVML could be used to support decision-makers in improving the financial resources to maintain and/or further support many environmental programs in years to come.

Environmental concerns, among other causes, are leading to meat replacement in the diet by healthy, nutritious and tasty foods. Alternative protein sources of plant origin can be an alternative to meat, but their low biological value proteins can be a problem. Novel foods, such as insect meals, can meet currently consumer demands. Therefore, this research has developed innovative prototypes of analogue burgers with animal and vegetable proteins. Concerned about health and allergies, a prototype incorporating soya to satisfy coeliacs was developed. An iterative and heuristic process was carried out to test the product development feasibility. The main raw materials used were insect flour (Tenebrio molitor), seitan and soya. In addition, oat and sodium alginate were used as binders. Shelf-life of the new product was evaluated by physicochemical (pH, aw, moisture, colour, acidity and peroxide index) and sensory analysis (quantitative analysis -QDA-). The production of the burger analogues was feasible. Product characterisation showed significant differences (p < 0.05) among samples for organoleptic properties, highlighting texture changes. Using a multivariate model, it was established “The best before date” at 7 days for all developed prototypes, conditioned by microbial growth. Finally, the spoilage model indicated an important contribution to bacterial growth with a notable modification in the pastiness and hardness of the burger analogues developed.

It is known from ancient Egyptian mathematical papyri that the Egyptians were able to calculate the area of a circle with great accuracy. How they found the formula for this calculation was still unknown. Here it is shown how the unknown ancient Egyptian mathematician found a method for calculating the area of a circle and the ratio of a circle’s circumference to diameter.

Waste-to-Hydrogen (Wahh) is a process of converting waste into hydrogen gas through various methods such as thermal conversion, biological conversion, and chemical conversion. This process not only helps in managing waste but also provides a clean source of energy as hydrogen is a renewable energy source that produces zero greenhouse gas emissions during combustion. Wahh has the potential to provide a sustainable solution for energy generation and waste management in the current scenario of globally increasing energy demands. This study aims to examine the properties and energy efficiencies of various renewable fuels including fuelwood, biogas, biomethane, and biohydrogen with a specific focus on differentiating the characteristics of biohydrogen. The paper explores the emerging concepts of waste-to-hydrogen microgrids, biohydrogen refineries, biohydrogen prosumer networks, and a biohydrogen circular economy, as well as Public-Private-People Partnerships (4Ps) and the hydrogen-centric renewable energy revolution, which are taking shape in industrialized countries. The study presents a comprehensive feasibility analysis of these concepts in the context of Nepal. The results of this research will provide valuable insights into the potential for adopting these innovative technologies in Nepal and will contribute to the development of a sustainable and efficient energy system.

Within this paper, a machine learning algorithm is used to investigate the importance of certain setpoints and parameters in the filtration processes of a large-scale water treatment facility. Previously, a model for the filtration process based on Run-to-Run Control was proposed and tested against sample data from the treatment plant, but it was quickly found that such a model was incompatible for successfully computing setpoints of operation which minimize the energy cost of running the filtration systems. The machine learning model described herein is an attempt to elucidate the importance of the available data on the filtration systems and to identify the most important variables that influence the filtration run time.

This research aims to contribute to the growing body of knowledge of Collaborative Consumption (CC) by exploring the motivations that influence the use of Peer-to-Peer (P2P) accommodation platforms from the demand side. There has been a significant increase in interest in sustainable choices regarding P2P accommodation in recent years. To address this gap and contribute to the collaborative consumption and P2P accommodation theory a quantitative study was conducted through a survey yielding 235 responses from both users and non-users of P2P platforms. The findings of this study suggest that P2P accommodation platform usage is influenced by multiple motivations, including sustainability, belonging, economic benefits, and convenience. Interestingly, the study also found that individuals with higher levels of academic qualifications are more likely to adopt this mode of consumption. Moreover, the study is the first of its kind to quantitatively address this topic and, therefore, contributes significantly to the field of collaborative consumption and P2P accommodation theory. By understanding the motivations of P2P platform users, policymakers and practitioners can develop targeted strategies to promote sustainable choices in this sector. Overall, this study provides a useful framework for future research on collaborative consumption and sustainable P2P accommodation.

The combination of non-steroidal anti-inflammatory drugs (NSAIDs) with non-opioid analgesics is common in clinical practice for the treatment of acute pain conditions like post-operative and post-traumatic pain. Besides that, and despite the very satisfactory results achieved by oral analgesics, parenteral analgesia is a key tool in the treatment of painful conditions when the enteral routes are not convenient. The parenteral ready-to-use fixed-dose combinations of NSAIDs with non-opioid analgesics like paracetamol or metamizole could play a central role in the treatment of painful conditions since they are able to gather into only one formulation the advantages of multimodal and parenteral analgesia. Surprisingly, only very recently a parenteral ready-to-use fixed-dose combination of Ibuprofen/Paracetamol was launched to the market. This review aims to review the current availability of NSAID-based Parenteral Fixed-dose combinations with paracetamol and metamizole in the European and American markets, and how the combination of such drugs could play a central role in a multimodal analgesia strategy. Also, it is explored how the parenteral formulations of NSAIDs, paracetamol, and metamizole could serve as starting elements for the development of new parenteral ready-to-use fixed-dose combinations. With this review, we concluded that, despite the well-recognized utility of combining NSAIDs with non-opioid analgesics, there are in the literature several randomized clinical trial studies unable to demonstrate clear advantages concerning their efficacy and safety. In the future, it is deemed necessary to perform clinical trials specifically designed to assess the efficacy and safety of these fixed-dose formulations to generate solid evidence of their clinical advantages.

In this paper, inspired by quantum field theory, or more specifically QED, we propose a dynamical model for relativity. By adopting the approach provided by this dynamical model, we provide a dynamical explanation for relativistic phenomena such as length contraction, time dilation and clock desynchronization. The result of the dynamical approach for clock desynchronization is especially interesting. Our dynamical approach exhausts the freedom for different clock synchronizations on frames accelerated from an initial reference frame, which is allowed by Einstein’s principle approach. Furthermore, our dynamical approach arrives at the interesting conclusion that Einstein’s equivalence principle and gravitational redshift are necessary to explain special relativistic clock desynchronization. This result shows that special relativity by itself is an incomplete theory. If our dynamical model assumptions are assumed to be valid at a fundamental level, it implies some modifications to quantum field theory and general relativity via the equivalence principle. These modifications have been discussed.

The manuscript presents a unified methodology for the engineering design of resonant inverters used for power sources to power various technologies based on induction heating. The methodology is compiled using the generalized consideration of electromagnetic processes in a series RLC circuit and the quasi-boundary method for the analysis of resonant inverters with and without reverse diodes operating in soft and hard commutation modes. On this basis, the transmission functions of the inverters are derived, and the matching between the parameters of the inverter and the load through complicated output circuits is also considered. The basic ratios for determining the circuit elements and their current and voltage loading are presented. The methodologies are verified using several computational examples, simulations and measurements from induction heating devices. The simplified design approach presented is useful for its application in power electronics training and also in the design of various devices using the principle of induction heating. Another important result is the achievement of formalization and algorithmization of the design process, which is a consequence of the application of a unified approach both in the analysis and in the design of a whole class of power electronic devices.

An out-of-hospital cardiac arrest (OHCA) is one of the leading causes of death in the world. The survival rate can be influenced by the Chain of Survival. The school is the institution that has the opportunity to promote the education of citizens in Basic Life Support (BLS), increasing the number of trained bystanders. This study aimed to identify the theoretical and practical knowledge and self-reported skills in BLS, in order to characterise the motivation to intervene in an emergency situation. A quantitative, descriptive, cross-sectional, and analytical study of the survey type was developed with a sample of 1215 students enrolled in 10th grade of secondary education in 2019-2020 in Portugal. The results point to a fragile appropriation of theoretical and practical knowledge in the field of BLS. Self-declared competences tend to rank below the theoretical knowledge manifested. Motivation to intervene is high: students are sensitive to the topic, willing to learn and highlight the importance and social relevance of the topic. We conclude that students do not feel nor are able to intervene in an OHCA episode. It seems necessary to develop didactic proposals that align the teaching of BLS with the Essential Learning at the end of compulsory education in Portugal.

Human and animal waste, including waste products originating from human or animal digestive systems such as urine, feces, and animal manure, have constituted a nuisance to the environment. Inappropriate disposal and poor sanitation of human and animal waste often cause negative impacts on human health through contamination of the terrestrial environment, soil, and water bodies. Therefore, it is necessary to convert these wastes into useful resources to mitigate their adverse environmental effect. The present study provides an overview and research progress of different thermochemical and biological conversion pathways for the transformation of human- and animal-derived waste into valuable resources. The physicochemical properties of human and animal waste are meticulously discussed as well as nutrient recovery strategies. In addition, a bibliometric analysis is provided to identify the trends in research and knowledge gaps. The results reveal that the U.S.A, China and England are the dominant countries in the research areas related to resource recovery from human or animal waste. In addition, researchers from the University of Illinois, the University of California Davis, the Chinese Academy of Science and Zhejiang University are front runners in research related to these areas. Future research should be centred on developing technologies for the on-site recovery of resources, exploring integrated resource recovery pathways, and exploring different safe waste processing methods.

The aim of this study was to estimate the association between fear of COVID-19 and risk perception with preventive behavior in health professionals from three Latin American countries. An analytical cross-sectional study was conducted. Health professionals with on-site care in Colombia, Ecuador, Guatemala, and Peru were surveyed. Information was collected through an online self-report questionnaire. The main variables were preventive behavior as the dependent variable and fear of COVID-19 and risk perception as independent variables. Linear regression was used, and Beta coefficients and p-values were calculated. 435 health professionals were included, the majority were aged 42 years or older (45.29%, 95%CI: 40.65%-50.01%) and female (67.82%, 95%CI: 63.27%-72.05%). It was shown that the greater the fear of COVID-19, the greater the preventive behavior of COVID-19 infection (B=2.21, p=0.002 for total behavior; B=1.12, p=0.037 for additional protection at work; B=1.11, p<0.010 for hand washing). The risk perception of COVID-19 infection had a slight direct relationship with preventive behaviors (B=0.28, p=0.021 for total behavior; B=0.13, p=0.015 for hand washing), with the exception of the preventive behavior of using additional protection at work (p=0.339). We found that fear and risk perception are associated with increased practice of hand washing and use of additional protection at work. Further studies are required on the influence of working conditions, job performance and the occurrence of mental health problems in frontline personnel with regard to COVID-19.

This article mainly proposes the point of view that financial literacy curriculum aims to make kinds of people, to make people with financial creativity of resource integration thinking and continuous ‘to conscience’ of morality, which is cultivate a way of thinking that can maximize benefits through the use of resource integration and constantly ‘to conscience’ to achieve goals for participants in financial structures with balanced interests. In this sense, this article argues that financial literacy is to make kinds of people with a financial mindset and constantly strengthen ‘to conscience’ through uniting of knowledge and action to achieve human well-being and benign operation of society. In this sense, this article attempts to determine what is really taught in financial literacy education in terms of curriculum theory. That is to improve creativity by cultivating financial thinking with constant ‘to conscience’. The views of this paper provide a new way of thinking about financial literacy education assessment. This changes the evaluation criteria of financial literacy education from the result-oriented of wealth growth to the process-oriented of financial creativity growth, trying to move the criticism of financial literacy education curriculum and evaluation from controversy to unity.

In previous studies regarding the osseointegration of zirconia (ZrO2) implants, a lack of consistency was observed in the surface topographies of the ZrO2 and Ti samples because of the difficult processability of ZrO2 surfaces. To resolve this problem, we used the molecular precursor method (wet process), which is a surface-modifying technique that can easily change the surface chemistry without changing the surface topography. A roughened Ti surface was prepared using sandblasting (large-grit) and acid treatment. We were able to create ZrO2-coated Ti implants with the same topography as that of roughened Ti substrates using the molecular precursor method, which solution contained a Zr complex. The uniform presence of tetragonal Zr was confirmed, and the apparent zeta potential of the surface of the ZrO2-coated Ti implant was higher than that of Ti. In animal experiments, ZrO2-coated Ti implants showed an equivalent or higher bone-to-implant contact ratio compared to that of the non-coated implants inserted into the femur bone defects of the rats. ZrO2 with the same surface topography as that of roughened Ti exhibits a promotion of osteogenesis equivalent to or better than that of Ti in the early stages of bone formation.

Modularity and organizational hierarchy are important concepts in understanding the structure and evolution of interactions in complex biological systems. In this work, we introduce and use a spectral characterization measure (Spectral Entropy) to quantify modularity in protein-to-protein interaction (PPI) networks in species across the tree of life. We evaluated the relation between the size of a PPI network and its (Spectral Entropy-based) modularity, and found a sigmoidal response between the two. We also found significant differences in the distribution of Spectral Entropy values among the three domains of life (Bacteria, Archaea, Eukaryotes). To explore further correlations with biological traits, we focused solely on bacterial PPI networks, which are the most numerous among the three domains and had associated trait metadata, and investigated how modularity impacts or is impacted by growth, aerobicity, selection and location on the tree of life. We found no relation between maximal growth rate and Spectral Entropy, but a strong dependence between G-C content (a proxy for selection) and Spectral Entropy. We also discovered that Spectral Entropy is negatively affected by phylogenetic placement (evolutionary distance from the last universal common ancestor). The general nature of the Spectral Entropy measure of hierarchical modularity in networks suggests that it will be useful in other settings where structural properties of real-world networks are being compared.