Inverse problems of recovering surface fluxes on the boundary of a domain from pointwise observations are considered. Sharp conditions on the data ensuring existence and uniqueness of solutions in Sobolev classes are exposed. They are smoothness conditions on the data, geometric conditions on the location of measurement points, and the boundary of a domain. The proof relies on asymptotics of fundamental solutions to the corresponding elliptic problems and the Laplace transform. The problem is reduced to a linear algebraic system with a nondegerate matrix.

This study aims to evaluate the land surface temperature (LST) and the thermal characteristics of the Urban Canopy Layer (UCL) of the urban canyon in Avenida Rio Branco in the Central Business District (CBD) of Rio de Janeiro during summer. In order to conduct this evaluation, two methods were employed: 1) TIRS Landsat-8 sensor for data selection and processing (latest generation, 2011-2020); ; 2) field survey using nine sampling points — seven along two mobile transects, one fixed point, and one vertical measurement point, which required the use of a RPA (Remotely Piloted Aircraft). Three categories of analysis were established for the field survey based on the prevailing synoptic situations: stability, instability, and post-instability. The CBD is characterized by extensive areas with surface heat islands, in which temperatures were higher than 38.9°C; the areas with milder LSTs were Campo do Santana, Avenida Rio Branco, and one of the Mixed-Use Zones (Praça Mauá). With respect to Rio Branco Avenue, the LST niches of lowest elevation were derived through building shadowing; however, the orbital data diverged from the observation data of the ten field-study days. In situ data revealed that the characteristics urban morphology of Avenida Rio Branco is susceptible to the formation of heat islands, presenting heat islands of very strong magnitude (over 6.1°C) in atmospheric stability, strong magnitude (4.1-6.0°C) in atmospheric instability, and moderate magnitude (2.1°C-4.0°C) in post-atmospheric instability. Despite the synoptic situation, thermal cores were concentrated at 1 pm. The intersection between Avenida Rio Branco, Rua do Ouvidor, and Praça Mauá stored most of the solar energy received during the day due to the greater sky obstruction caused by the verticalization. Finally, vertical analysis demonstrated the formation of a thermal inversion on the night of the highest mean air temperature (29.5°C), probably, due to the roughness and number of buildings in the urban canyon.

Tree resin, which in addition to its widespread use in industry is also a macroergic component which has not yet been used for energy purposes. The main goal of this work is to determine the energy content of the resin of spruce, pine and larch and wood components – pulp and turpentine. The combustion heats of resin (MJ/kg) from each timber was determined calorimetrically. The energy values of tree resin (>38.0 MJ.kg-1) were 2.2 and 2.4 times higher than that of bleached and unbleached cellulose, the highest value was recorded for the turpentine (>39.0 MJ.kg-1). The best way of resin tapping is the America method, providing 5 kg resin ha-1 yr-1. The resin quantity tapped was raised at least 3 times applying stimulant, its production cost compared to other feedstocks was the cheapest. The tree resin can be applied as a good means to mitigate global warming and consequently dampen climate change. One tonne of tree resin burned instead of coal spares the atmosphere by 5.0 Mt CO2 since it is environmentally neutral. As resin heating values approach to the lower end of ones of liquid hydrocarbon fuels, greater efforts are needed to examine the most efficient energy use of resin.

This paper presents a steady-state and transient heat conduction analysis framework using the polygonal scaled boundary finite element method (PSBFEM) with polygon/quadtree meshes. The PSBFEM is implemented with commercial finite element code Abaqus by the User Element Subroutine (UEL) feature. The detailed implementation of the framework, defining the UEL element, and solving the stiffness/mass matrix by the eigenvalue decomposition are presented. Several benchmark problems from heat conduction are solved to validate the proposed implementation. Results show that the PSBFEM is reliable and accurate for solving heat conduction problems. Not only can the proposed implementation help engineering practitioners analyze the heat conduction problem using polygonal mesh in Abaqus, but it also provides a reference for developing the UEL to solve other problems using the scaled boundary finite element method.

Air pollution is responsible for any adverse effects on human beings. Thermal discomfort, on the other hand, is able to overload the human body and eventually provoke health implications due to the heat imbalance. Methods: The aim of the present work is to study the behavior of two bio-climatic indexes and statistical characteristics of the air quality index for Sofia city - the capital of Bulgaria for the period 2008 - 2014. The study is based on WRF-CMAQ model system simula-tions with a spatial resolution of 1 kilometer. The air quality is estimated by the air quality index, taking into account the influence of different pollutants and the thermal conditions by two indi-ces, respectively, for hot and cold weather. Results: It was found that half of the heat and cold index categories are present in the simulations. Their distribution has some spatial features. All air quality categories are present in the domain, with dominance only of the O3 and PM10. Conclu-sions: It was found that Sofia is not so hot and air polluted place, but in some situations, people have to have some concerns when intend to be outdoors for a prolonged time.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

An exact spherically symmetric and magnetically charged black hole solution in 4D Einstein-Gauss-Bonnet gravity coupled to nonlinear electrodynamics (NED) is obtained. The NED Lagrangian is given by ${\cal L}_{NED} = -{\cal F}/(1+\sqrt[4]{2\beta{\cal F}})$, where ${\cal F}$ is the field invariant. We study the thermodynamics calculating the Hawking temperature and the heat capacity of the black hole. The phase transitions take place when the Hawking temperature has an extremum and the heat capacity is singular. We demonstrate that black holes are thermodynamically stable in some range of event horizon radii where the heat capacity is positive. The BH shadow radii are calculated. It is shown that when increasing the nonlinearity parameter $\beta$ the BH shadow radius is decreased.

Mass timber products, together with careful forestry management, could help decarbonize the construction industry. These products must be long-lasting, to safely store atmospheric carbon for decades or centuries, and multi-functional, to displace materials and equipment that are emissions-intensive. This paper shows how to optimize mass timber panels as heat-exchangers, suggesting how to eliminate insulation while simplifying HVAC systems. Test panels measured the heat-exchange in steady and transient conditions, when the ventilation was driven by a fan or by thermal buoyancy. The total heatexchange was predicted accurately by theory in all cases. Further investigation is needed to understand the possible heat-recovery effects at the exterior surface.

In order to design efficient and sustainable office spaces and to automate lighting, heating and air circulation in these facilities, solving the challenge of occupancy prediction is crucial. In office spaces where large areas need to be observed, multiple sensors must be used for full coverage. In these cases, it is normally important to keep the costs low, but also to make sure that the privacy of the people who use such environments are preserved. Low-cost and low-resolution heat (thermal) sensors can be very useful to build solutions that address these concerns. However, they are extremely sensitive to noise artifacts which might be caused by heat prints of the people who left the space or by other objects which are either using electricity or exposed to sunlight. There are some earlier solutions for occupancy prediction that employ low-resolution heat sensors, however, they have not addressed nor compensate for such heat artifacts. Therefore, in this paper, we present a low-cost and low-energy consuming smart space implementation to predict the number of people in the environment based on whether their activity is static or dynamic in time. We use a low-resolution (8×8) and non-intrusive heat sensor to collect data from an actual meeting room. We propose two novel workflows to predict the occupancy; one based on computer vision and one based on machine learning. Besides comparing the advantages and disadvantages of these different workflows, we use several state-of-the-art explainability methods in order to provide a detailed analysis of the algorithm parameters and how the image properties influence the resulting performance. Furthermore, we analyze noise resources which affect the heat sensor data. We hope that our analysis brings light into understanding how to handle very low-resolution heat images in these environments. The presented workflows could be used in various domains and applications other than smart offices, where occupancy prediction is essential, e.g., for elderly care.

District heating networks have become widespread due to their ability to distribute thermal energy efficiently, which leads to reduced carbon emissions and improved air quality. The characteristics of these networks vary remarkably depending on the urban layout and system amplitude. Moreover, extensive data about the energy distribution and thermal capacity of different areas are seldom available. Design, optimization and control of these systems are enabled by the availability of fast and scalable models of district heating networks. This work addresses this issue by proposing a novel method to develop a scale-free model of large-scale district heating networks. Starting from coarse data available at the main substations, a physics-based model of the system aggregated regions is developed by identifying the heat capacity and heat loss coefficients. The model validation on the network of Västerås, Sweden, shows compatibility with literature data and can therefore be exploited for system design, optimization and control-oriented applications. In particular, the possibility to estimate the heat storage potential of network regions allows new smart management strategies to be investigated.

The paper presents the results of energy and environmental analysis of geothermal CHP plant operation in Polish conditions. As the most favorable, for the geothermal conditions prevailing in Poland, the variant of CHP plant based on Organic Rankine Cycle (ORC) has been taken into consideration. As the case study the existing geothermal well located in the town of Konin in the Wielkopolska voivodship has been chosen. The conceptual design of CHP plant has been proposed and evaluated from energy and environmental point of view. As energy performance criteria the non-renewable primary energy consumption has been chosen. In case of environmental performance carbon dioxide emission has been taken as evaluation criteria. The analysis has been performed for different operating conditions and three working fluids.

One way to increase overall natural gas engine efficiency is to transform exhaust waste heat into useful energy by means of a bottoming cycle. Organic Rankine cycle (ORC) is a promising technology to convert medium and low grade waste heat into mechanical power and electricity. This paper presents an energy and exergy analysis of three ORC-Waste heat recovery configurations by using an intermediate thermal oil circuit: Simple ORC (SORC), ORC with Recuperator (RORC) and ORC with Double Pressure (DORC), and Cyclohexane, Toluene and Acetone have been proposed as working fluids. An energy and exergy thermodynamic model is proposed to evaluate each configuration performance, while available exhaust thermal energy variation under different engine loads was determined through an experimentally validated mathematical model. Additionally, the effect of evaportating pressure on net power output , absolute thermal efficiency increase, absolute specific fuel consumption decrease, overall energy conversion efficiency, and component exergy destruction is also investigated. Results evidence an improvement in operational performance for heat recovery through RORC with Toluene at an evaporation pressure of 3.4 MPa, achieving 146.25 kW of net power output, 11.58% of overall conversion efficiency, 28.4% of ORC thermal efficiency, and an specific fuel consumption reduction of 7.67% at a 1482 rpm engine speed, a 120.2 L/min natural gas Flow, 1.784 lambda, and 1758.77 kW mechanical engine power.

The limitations of investment casting of cobalt-based alloys are claimed to be less problematic with significant improvements in metal additive manufacturing by selective laser melting (SLM). Despite these advantages, the metallic devices are likely to display mechanical anisotropy in relation to build orientations, which could consequently affect their performance ‘in vivo’. In addition, there are inconclusive evidence concerning the requisite composition and post-processing steps (e.g. heat-treatment to relieve stress) that must be completed prior to the devices being used. In the current paper, we evaluate the microstructure of ternary cobalt-chromium-molybdenum (Co-Cr-Mo) and cobalt-chromium-tungsten (Co-Cr-W) alloys built with Direct Metal Printing and LaserCUSING SLM systems respectively at 0°, 30°, 60° and 90° inclinations (Φ) in as-built (AB) and heat-treated (HT) conditions. The study also examines the tensile properties (Young's modulus, E; yield strength, R_P0.2; elongation at failure, A_t and ultimate tensile strength, R_m), relative density (RD), and micro-hardness (HV5) and macro-hardness (HV20) as relevant physico-mechanical properties of the alloys. Data obtained indicate improved tensile properties and HV values after short and cost-effective heat-treatment cycle of Co-Cr-Mo alloy; however, the process did not homogenize the microstructure of the alloy. Annealing heat-treatment of Co-Cr-W led to significant isotropic characteristics with increased E and A_t (except for Φ = 90º) in contrast to decreased R_P0.2, R_m and HV values, compared to the AB form. Similarly, the interlaced weld-bead structures in AB Co-Cr-W were removed during heat-treatment, which led to a complete recrystallization in the microstructure. Both alloys exhibited defect-free microstructures with RD exceeding 99.5%.

The key anthropogenic effects on climate include the changes in land use and emission of greenhouse gases into the atmosphere. Depletion of vegetation poses serious threat that speeds the process of climate change and reduces carbon sequestration by the environment. Thus, the preservation of natural environment in urban areas is an essential component of the garden city model, proposed by Sir Ebenezer Howard in 1898, to ensure ecological balance. Recent Landsat images showed that Kumasi does not have the required percentage of green vegetation as was stipulated in the garden city model on which the city was built. It was observed that most parts of Kumasi's green vegetation have been lost to built environments. This study was conducted to assess the impact of urbanization on the garden city status and its effect on the micro-climate of the city. Significant changes in the vegetation cover of the city was evaluated from Landsat-TM imagery and analysis of a long term climatic data of Kumasi carried out over a 55-year period (1960 to 2015). It was observed that, climatic conditions have slightly changed, as mean surface temperature of has increased by 1.2 °C/ 55 years, due to the significant landuse changes from development of non-transpiring, reduced evaporative urban surfaces. However, the impact is not greatly felt due to the geographical location of the city on the globe despite the evidence of a considerable temperature change. Green vegetation conservation for the city is recommended as a top priority in future for city authorities and planners.

Batch combustion in wood log stoves is a promising application for latent heat storage (LHS), due to the transient heat production with high peak effects. The current study aimed at designing a compact, passive and durable LHS system storing a substantial part of the heat release during batch combustion and effectively releasing the stored heat to the room for 6 to 10 hours after the last batch. The LHS system consists of a coaxial cylinder located at the top of the wood stove, replacing part of the regular stovepipe. Internal metallic fins were applied as heat transfer enhancement to homogenize the temperature distribution inside the PCM. The effect of radial fin lengths was numerically investigated through a parametric study using five different fin lengths within the PCM. Using 35-mm fins in the 70-mm PCM layer yielded the best trade-off for the application. This configuration enabled achieving a slow but close to complete melting of the PCM within a realistic combustion duration, while avoiding overheating the PCM above its degradation temperature. Thereafter, the discharge allowed releasing the stored latent heat for 6 hours. The exhaust gas inlet temperature proved to have a strong influence on the PCM thermal performance.

Heat stress affects the yield of medicinal plants and can reduce biomass and/or metabolite production. In order to evaluate the effect of heat-induced stress on the essential oil production in Mentha x piperita L. var. Mitcham (Mitcham mint) and Mentha x arvensis var. piperascens Malinv. ex L. H. Bailey (Japanese mint), we studied the chemical composition of the oils of the two mint species under different heat shock stress in growth chambers. The antibacterial activity of the essential oils was also evaluated; microscopic observation (fluorescence and electron transmission) was used to assess the effect of the tested samples on bacterial growth. The results obtained shed light on the mint essential oils composition and biological activity in relation to heat stress.

In urban area, one of the great problem is the rise of temperature, which leads to form the urban heat island effect. This paper refers to the trend of the urban surface temperature extracted from the Landsat images from which to consider changes in the formation of surface urban heat island for the north of Ho Chi Minh city in period 1995-2015. Research has identified land surface temperature from thermal infrared band, according to the ability of the surface emission based on characteristics of normalized difference vegetation index NDVI. The results showed that temperature fluctuated over the city with a growing trend and the gradual expansion of the area of the high-temperature zone towards the suburbs. Within 20 years, the trend of the formation of surface urban heat island with two typical locations showed a clear difference between the surface temperature of urban areas and rural areas with space expansion of heat island in 4 times in 2015 compared to 1995. An extreme heat island located in the inner city has an area of approximately 18% compared to the total area of the region. Since then, the solution to reduce the impact of urban heat island has been proposed, in order to protect the urban environment and the lives of residents in Ho Chi Minh City becoming better

The sustainability of the planet and its inhabitants is in dire danger and is among the highest priorities on global agendas such as the Sustainable Development Goals (SDGs) of the United Nations (UN). Solar energy -- among other clean, renewable, and sustainable energies -- is seen as essential for environmental, social, and economic sustainability. Predicting solar energy accurately is critical to increasing reliability and stability, and reducing the risks and costs of the energy systems and markets. Researchers have come a long way in developing cutting-edge solar energy forecasting methods. However, these methods are far from optimal in terms of their accuracies, generalizability, benchmarking, and other requirements. Particularly, no single method performs well across all climates and weathers due to the large variations in meteorological data. This paper proposes SENERGY (an acronym for Sustainable Energy), a novel deep learning-based auto-selective approach and tool that, instead of generalising a specific model for all climates, predicts the best performing deep learning model for GHI forecasting in terms of forecasting error. The approach is based on carefully devised deep learning methods and feature sets through an extensive analysis of deep learning forecasting and classification methods using ten meteorological datasets from three continents. We analyse the tool in great detail through a range of metrics and methods for performance analysis, visualization, and comparison of solar forecasting methods. SENERGY outperforms existing methods in all performance metrics including Root Mean Square Error (RMSE), Mean Absolute Error (MAE), Mean Absolute Percentage Error (MAPE), Forecast Skills (FS), Relative Forecasting Error, and the normalised versions of these metrics. The proposed auto-selective approach can be extended to other research problems such as wind energy forecasting and predict forecasting models based on different criteria (in addition to the minimum forecasting error used in this paper) such as the energy required or speed of model execution, different input features, different optimisations of the same models, or other user preferences.

Background: Many risk-modifying factors affect cancer incidence and mortality rates. Solar UVB reduces cancer risk by producing vitamin D, which has many mechanisms to reduce risk of cancer incidence, progression, and metastasis. Obesity increases cancer risk through several mechanisms, including increased inflammation. Method and Materials. We present an ecological study (a type of observational study) of incidence and/or mortality rates for cancers during 2007–2016 of 17 anatomical sites with respect to solar ultraviolet-B (UVB) doses and obesity prevalence. Data were averaged for 12 geographical regions. Results: Solar UVB doses were significantly inversely correlated with incidence rates for three types of cancer for males. They were inversely correlated with mortality rates for five cancers for males and four for females. Obesity prevalence was directly correlated with mortality rates for three cancers for males and seven for females. Discussion: The ecological approach has certain limitations, such as its sensitivity only to regional variations in relation to specific risk-modifying factors. In this study, these limitations include numerous factors influencing cancer risk and the fact that the data are averaged across entire regional populations, which may not reflect individual risks. Despite this, the study reveals important correlations. Specifically, it found that solar UVB exposure is linked to a lower risk of certain cancers, while obesity is associated with an increased risk of some cancers in France. These findings are consistent with results from a similar study in the United States on cancer rates between 2016 and 2020. The association between obesity and cancer risk aligns with other observational studies. However, it is uncertain to what extent higher solar UVB exposure or elevated serum 25-hydroxyvitamin D levels might mitigate the impact of obesity on cancer risk. Reducing cancer mortality in France may be achievable through vitamin D supplementation and efforts to lower obesity prevalence.

Solar radiation corresponds to fundamental parameters for solar photovoltaic (PV) technology. Reliable solar radiation prediction became valuable to design solar PV systems, performance, operatively efficient planning, safety operation, grid dispatch and financial characteristics. However, high quality ground-based solar radiation measurements are scarce, especially for very short-term time horizon. Most of the existent studies trained the machine learning (ML) model used dataset with time horizon of 1-hour or day, very fewer studies have been reported using a dataset with a 1-mitute time horizon. In this study, a comprehensive evaluation of nine ensemble learning algorithms (ELA) is performed to estimate the solar radiation in Santo Domingo with a 1-minute time horizon dataset collected from a local weather station. The ensemble learning evaluated included seven homogeneous ensembles; Random Forest (RF), Extra Tree (ET), Adaptive Gradient Boosting (AGB), Gradient Boosting (GB), Extreme Gradient Boosting (XGB), Light Gradient Boosting (LGBM), Histogram-based Gradient Boosting (HGB) and heterogeneous ensemble named as Voting and Stacking. RF, ET, GB, HGB were combined to develop Voting and Stacking and Linear Regression (LR) was adopted in the second layer of the Stacking. Five technical metrics, Mean Squared Error (MSE), Root Mean Squared Error (RMSE), Mean Absolute Error (MAE), Mean Absolute Percentage Error (MAPE) and Coefficient of Determination (R2) were used as criteria to determine the prediction quality of the developed ensemble algorithms. Comparison of the results indicates that the HGB algorithm offers superior prediction performance among the homogeneous ensemble learning and overall, the Stacking provides the best accuracy with metric values of MSE=3218.27, RMSE= 56.73, MAE=29.87, MAPE=10.60, R2=0.964.

Solar radiation impacts diverse aspects of city life, such as harvesting energy with PV panels, passive heating of buildings in winter, cooling loads of air-conditioning systems in summer, and urban microclimate. Urban digital twins and 3D city models can support solar studies in the process of urban planning and provide valuable insights for data-driven decision support. This study examines the calculation of solar incident radiation at the city scale in Sofia using remote sensing data for the large shading context in a mountainous region and 3D vector building data. The building footprints and the terrain are preprocessed using GIS. The solar calculation uses a raytracing algorithm in 3D CAD at the city scale. To evaluate the performance, two cases were considered at the city and district scale, respectively. The total face count of meshes for the simulations constituted approximately 2 000 000 faces. 64379 roofs for the whole city and 4796 buildings for one district were selected. All calculations were performed in one batch and visualized in a 3D web platform. Using a 3D CAD environment establishes a seamless process of updating 3D models and simulations while preprocessing in GIS ensures working with large-scale datasets. The proposed method showed moderate computation time for both cases and could be extended to include reflected radiation and dense photogrammetric meshes in the future.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

The result of the multidisciplinary collaboration of researchers from different areas of knowledge to validate a solar radiation model is presented. The MAPsol is a 3D local-scale adaptive solar radiation model that allows to estimate direct, diffuse and reflected irradiance for clear sky conditions. The model includes the adaptation of the mesh to complex orography and albedo, and considers the shadows cast by the terrain and buildings. The surface mesh generation is based on surface refinement, smoothing and parameterisation techniques and allows the generation of high quality adapted meshes with a reasonable number of elements. Another key aspect of the paper is the generation of a high-resolution digital elevation model (DEM). This high-resolution DEM is constructed from LiDAR data and its resolution if two times more accurate than the publicly available DEMs. The validation process uses direct and global solar irradiance data obtained from pyranometers at the University of Salamanca located in an urban area affected by systematic shading from nearby buildings. This work provides an efficient protocol for studying solar resources, with particular emphasis on areas of complex orography and dense buildings where shadows can potentially make solar energy production facilities less efficient.

With the popularity of solar energy in the electricity market, demand arises for data such as precise locations of solar panels for efficient energy planning, management, and distribution. However, this data is not easily accessible and in some cases, information such as precise locations does not exist. Furthermore, existing data sets for training semantic segmentation models of PV installations are limited, and their annotation is time-consuming and labor-intensive. Therefore, for additional remote sensing (RS) data creation, the pix2pix generative adversarial network (GAN) is utilized, enriching the original resampled training data of varying GSDs without compromising its integrity. Experiments done with the DeepLabV3 model, ResNet-50 backbone, and pix2pix GAN architecture were conducted to find the optimal configuration for an accurate RS imagery segmentation model. The result is a fine-tuned solar panel semantic segmentation model, trained using transfer learning and utilizing an optimal amount – 60% of generated RS imagery for additional training data, increasing model accuracy. The findings demonstrate the benefits of using GAN-generated images as additional training data, increasing the size of small data sets, and improving the capabilities of the segmentation model for solar panel detection in RS images.

Efficient implementation of clean energy technologies, including pioneering solutions like mobile solar PV systems mounted on trailers (MSPT), is pivotal for addressing energy challenges, especially in regions with constrained power grid access. This endeavour is vital for meeting escalating elec-tricity demands and aligning with the UN Sustainable Development Goal (SDG) aimed at ensuring dependable and sustainable energy provision in developing countries. This paper investigates the aerodynamic behaviour of a designed MSPT using numerical and experimental approaches. Spe-cifically, the study focuses on the effects of wind velocity and tilt angels on the drag and lift forces, as well as drag and lift coefficients on the panel used in the MSPT system. Additionally, the overall wind force acting on the entire MSPT (including 9 large solar PV panels) was examined, considering the combined effects of wind flow and the system's geometry. The simulations were conducted using ANSYS-Fluent software and experimental testing was performed utilizing scaled-down models to validate the accuracy of the simulation. The insights and the knowledge from this study can be utilized to optimize the design, installation, and operation of such systems, ultimately enhancing their performance, reliability, and paving ways for further improvements in mobile solar PV technology.

The prohibitive costs of small-scale solar photovoltaic (PV) racks decreases PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt mounted racking designs that allow manual change of tilt angle from zero to 90 degrees by varying the length of cables. The racks are designed using the calculated dead, wind and snow loads for Canada as conservative design for most of the rest of the world. Structural capacities of the wooden members are then ascertained and resisting bending moment, shear force, tensile force, and compressive force for them is calculated. A structural and truss analysis is performed to ensure that racking design with-stands the applicable forces. Moreover, implications of changing the tilt angle on the wooden members/cables used to build the system are also determined. The systems offer significant economic savings ranging from 1/3rd to 2/3rd the capital expenses of the commercially available alternatives. In addition, the racking designs are easy-to-build and require minimal manufacturing operations, which increases their accessibility. The stilt-mounted designs can be employed for agrivoltaic settings while allowing farm workers shaded ergonomic access to perform planting, weeding, and harvesting.

Solar heating technology is a promising solution to promote China to achieve the “3060 double carbon” target as soon as possible. And seasonal thermal storage (STS) can effectively solve the mismatch problem of solar heating systems between the supply and demand of thermal energy. Due to the instability of solar radiation resources and heat demand, it is necessary to analyze the dynamic response characteristics of the system. Yet, related studies are still scarce. In this study, a solar heating system with a solar tower receiver and STS was introduced in north China. The dynamic performance of the system is analyzed with a dynamic simulated method in a typical day or typical operation modes, and the switch mechanism between multiple operation modes is also revealed. The impact of different heating strategies on system performance was analyzed. Results showed that the solar fraction of the system reached 89.4% in the third year, which was 3.6% higher than the first year. The quality-quantity heating operation strategies can be effective ways to improve the discharge efficiency of STS and the system performance without any heat pump. The electricity consumption of the pump on the heating side could be significantly reduced by 44.6% compared with the quality control.

In this work we explore the utilization of plasmonic resonance (PR) in silver nanowires to enhance the performance of organic solar cells. Plasmonic resonance is a phenomenon in which nanoscale conductive materials exhibit oscillation of conduction electrons, resulting in the creation of an electric field. Enhancing light absorption is crucial for improving organic solar cell efficiency and incorporating metallic nanostructures to induce surface plasmon resonance (SPR) shows promise in achieving this goal. We discuss the two key mechanisms of plasmonic effects: far-field scattering and near-field resonance modes. Far-field scattering extends the optical path of incident light, while near-field plasmonic effects involve localized surface plasmon resonance (LSPR) and plasmonic cavity modes, enhancing absorption by strengthening electric fields near the nanostructures. Silver nanowires are the focus of this study, and finite-difference time-domain (FDTD) simulation software is used to investigate their plasmonic resonance behavior in a ZnO/Silver nanowires/ZnO (ZAZ) electrode structure. The simulations reveal the dominance of LSPR in this configuration, with intense electric fields inside the nanowire and propagation into the surrounding medium, offering opportunities for enhanced light absorption in the organic solar cell's active layer.

Integrating numerous renewable resources has been extensively researched and studied to create a dependable energy system. This study investigated the best techno-economical hybrid energy system configuration while using hydrogen energy to keep the system's energy balanced. Additionally, this study aims to determine the best hybrid system configuration for the location under investigation. A novel technique of DBM (Deterministic Balanced Method) was introduced to determine the total annual energy output for the project's lifetime. This approach is used to contrast the outcomes of other HOMER software tools. Then, using HOMER, it is possible to confirm the sizing optimization results for the suggested method by comparing the power ratings and yearly energy output. A detailed comparison between our proposed method and HOMER Pro has been conducted for validation and verification. Our method has been rigorously tested in various hybrid off-grid energy systems, ensuring its applicability and reliability across different scenarios and configurations. The results of our study indicate a high degree of similarity between the proposed approach and HOMER pro for computing annual energy power for the studied energy systems. Specifically, our analysis revealed that the difference between the approaches was within a range of 5%, indicating a high level of consistency and reliability in our method. These findings suggest that our approach can be confidently applied to determine the appropriate size of hybrid energy systems accurately. Overall, our study provides valuable insights into the development of effective sizing methodologies for hybrid energy systems. After considering the amount of solar radiation and wind speed gathered by global weather data platforms like NASA and METEONORM, this paper has also included a real case study of the Cairo International Airport's hybrid renewable energy production systems. To guarantee the viability of this study, the system design was founded on an actual load that was researched and simulated. A cluster of distributed networks was finally proposed to use the excess energy and enable energy conversion processes to be used in industry and transportation applications.

Canada has committed to reducing greenhouse gas (GHG) emissions by increasing the non-emitting share of electricity generation to 90% by 2030. As solar energy costs have plummeted, agrivoltaics (co-development of solar photovoltaic (PV) systems and agriculture) provide an economic path to these goals. This study quantifies agrivoltaic potential in Canada by province using geographical information system analysis of agricultural areas and numerical simulations. Systems modeled would enable conventional farming of field crops to continue (and potentially increase yield) by using bifacial PV for single-axis tracking and vertical system configurations. Between a quarter (vertical) to more than one third (single axis tracking) of Canada’s electrical energy needs can be provided solely by agrivoltaics using only 1% of current agricultural lands. These results show that agrivoltaics could be a major contributor to sustainable electricity generation and provide the ability for Canada to render the power generation sector net zero/GHG emission free. It is clear that the potential of agrivoltaic-based solar energy production in Canada far outstrips current electric demand and can thus be used to electrify and decarbonize transportation, heating, expand economic opportunities by powering the burgeoning computing sector, and export green electricity to the U.S. to help eliminate their dependence on fossil fuels.

This work deals with the performance evaluation of novel flat photovoltaic-thermal (PV-T) modules under vacuum. Through a 1D (dimensional) steady-state-energy-balance numerical model developed in MATLAB, two different layouts are studied: the first consisting of a photovoltaic (PV) cell installed just below the glass encapsulating the flat panel, and the second where the PV cell is placed on the selective solar absorber (SSA). In both cases the thermal and electrical efficiencies have been evaluated at different SSA operating temperatures, in the range of 323 K to 423 K. The analysis has been conducted at different energy bandgap (E_bg) of the PV cell and assuming a variable transmittance or emittance of the PV cell, depending on the design. The two systems efficiency comparison has been carried out at the same operating temperature. Overall, this work highlights the importance of high vacuum insulation, which guarantees the reduction of convective thermal losses, and shows that the maximum energy is produced for PV cells with E_bg ≈1.5-1.7 eV, depending on layout and operating temperature, by including the thermal output in the PV-T optimization. The energy and exergy efficiencies obtainable using the proposed PV-T systems are considerably improved compared to the results previously reported in the literature.

Solar cell layers technology has achieved global standing in the solar cell layers deposition process, and it covers the innovative methods and techniques in significant applications. Recent solar cell layers technology has an advanced interest in a refined approach to enhance performance and highlights the importance of recent proficient procedures for manufacturing. For example, the application is used to search for novel materials for solar cells' layers to clarify the current energy crisis. The technological process and various types of solar cells depend on climate change. Among them, layers of solar cells and silicon wafer solar cells are very encouraging. Solar cell layers technology has led to solar cells being a more reasonable active option in design and production. The productivities facilitated by new solar cells still need to be enhanced for the various processes involved in the additional enhancement from Copper Indium Gallium Selenide (CIGS) microfilms to solar cell crystal structure dye-sensitized solar cells. The hydrophobic coating works as an anti-dust coating, enhancing efficiency and decreasing the cost of cleaning solar cells. In Saudi Arabia Majmaah City, most solar projects are in dry regions, where the dusty weather reduces solar cell efficiency. Therefore, combining these two properties and applying an anti-reflective and superhydrophobic coating will increase solar cell efficiency by 20%. Solar cells' crystal structure results are substituted with layers or new materials to balance environmental impact and toxic nature.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

NASA’s ICESat-2space-borne photon-counting lidar mission is providing global elevation measurements that will provide significant benefits to a variety of bio-geoscience research applications. Given the novelty of elevation and the derived data products from the ICESat-2 mission, the research community needs software tools that can facilitate photon-level analyses to support product validation and development new analysis methods. Here, we describe PhotonLabeler, a free graphic user interface (GUI) for manual labeling and visualization of ICESat-2 Geolocated Photon data (ATL03). Developed in MATLAB, the GUI facilitates the reading and display of ATL03 Hierarchical Data Format (HDF) files, the manual labeling of individual photons into target classes of choice using a number of point selections tools and enables eventual saving of labeled data in ASCII format. Other capabilities include saving and loading of labeling sessions to manage labeling tasks over time. We expect labeled data generated using the application to serve two main purposes. First, serve as ground truth for validating various products from ICESat-2 mission, especially for study sites around the world that do not have existing reference datasets such as airborne lidar. Second, serve as training and validation data in the development of new algorithms for generating various ICESat-2 data products. We demonstrate the first use case through a validation case study for the land and vegetation product (ATL08), which provides canopy and terrain height estimates, over two sites. For the first site, located in northwestern Zambia, we used ICESat-2 ATL03 data acquired at night and for our second site in Texas, US, we used ATL03 data acquired during the day. The PhotonLabeler application is freely available as a compiled MATLAB binary to enable free access and utilization by interested researchers.

The hybrid system is analyzed and optimized to produce electric energy in Non-Interconnected Zones in the Colombian Caribbean region, contributing both to the improvement in the reduction of greenhouse gas emissions and to the rational use of energy. A comparative analysis of the performance of these systems was carried using a dynamic model in real wind and solar data. The model is integrated by a Southwest Wind Power Inc. wind turbine. AIR 403, a proton exchange fuel cell (PEM), an electrolyze, a solar panel and a charge regulator based on PID controllers to manipulate oxygen and hydrogen flows in the cell. The transient responses of the cell voltage, current, and power were obtained for the demand of 200 W for changes in solar radiation and wind speed for all days of the year 2013 in the Ernesto Cortissoz airport, Puerto Bolívar, Alfonso Lopez airport and Simon Bolívar airport, by regulating the flow of hydrogen and oxygen into the fuel cell. The maximum contribution of power generation from the fuel cell was presented for the Simon Bolívar airport in November with a value of 158,358W (9.45%). A multi-objective design optimization under a Pareto front is presented for each place studied to minimize the Levelized Cost of Energy and CO₂ emission, where the objective variables are the number of panel and stack in the PV system and PEM.

Stabilized un-doped Zinc Telluride (ZnTe) thin films were grown on glass substrates under vacuum using closed space sublimation (CSS) technique. A dilute copper nitrate solution (0.1/100 ml) was prepared for copper doping known as ion exchange process in the matrix of ZnTe thin film. The reproducible polycrystalline cubic structure of undoped and Cu doped ZnTe thin films with preferred orientation (111) was confirmed by X-rays diffraction (XRD) technique. Lattice parameter analyses verified the expansion of unit cell volume after incorporation of Cu species into ZnTe thin films samples. The micrographs of scanning electron microscopy (SEM) were used to measure the variation in crystal sizes of samples. The energy dispersive X-rays was used to validate the elemental composition of undoped and Cu-doped ZnTe thin films. The bandgap energy 2.24 eV of ZnTe thin film decreased after doping Cu to 2.20 eV may be due to the introduction of acceptors states near to valance band. Optical studies showed that refractive index was measured from 2.18 to 3.24 whereas thicknesses varied between 220 nm to 320 nm for un-doped and Cu doped ZnTe thin film respectively using Swanepoel model. The oxidation states of Zn⁺², Te⁺² and Cu⁺¹ through high resolution X-ray photoelectron spectroscopy (XPS) analyses was observed. The resistivity of thin films changed from ~10⁷ Ω-cm for undoped ZnTe to ~1 Ω-cm for Cu-doped ZnTe thin film, whereas p-type carrier concentration increased from to respectively. These results predicted that Cu-doped ZnTe thin film can be used as an ideal, efficient and stable intermediate layer between metallic and absorber back contact for the heterojunction thin film solar cell technology.

Recently, solar energy is growing as a power source for potential alternative to meet the global demand. Unlike other energy sources such as coal, nuclear, gas and oil, their prices are not only stable, they prevent the harmful side-effects on the environment, being one of the best sources of clean energy (solar energy). This article presents an analysis of the transformation of the static system for the treatment of solar energy using photovoltaic modules. It is designed to generate energy for future generations to be more useful from different parts of the photovoltaic energy conversion system, such as a DC-DC converter, current inverter, maximum power tracking algorithm (MPPT), filter, the stability of a system, etc. The above result will be useful in the improvement of efficiency in photovoltaics structures.

In this paper, the forecast horizon and solar variability influences on MHFM model based on multiscale decomposition, AR and NN models, are studied. This article follows the works published in [1] showing the performance of the MHFM using 3 multiscale decomposition methods and a forecast horizon equal to 1 hour. Several forecast horizon strategies and his influence on the MHFM performances are investigated. We show that the best strategy for a rRMSE variying from $4.43\%$ to $10.24\%$ is obtained for forecast horizons from $5$ minutes to $6$ hours. In a second part, the solar variability influence on the MHFM is studied. A classification based on a shows that the best performance of MHFM is obtained for clear sky days with a rRMSE of $2.91\%$ and worst for cloudy sky days with a rRMSE of $6.73\%$.

The main features of the instrumental global mean surface temperature (GMST) are reasonably well described by a simple linear response model driven by anthropogenic, volcanic and solar forcing. This model acts as a linear long-memory filter of the forcing signal. The physical interpretation of this filtering is the delayed response due to the thermal inertia of the ocean. This description is considerably more accurate if El Ni\~{n}o Southern Oscillation (ENSO) and the Atlantic Multi-decadal Oscillation (AMO) are regarded as additional forcing of the global temperature and hence subject to the same filtering as the other forcing components. By considering these as predictors in a linear regression scheme, more than 92\% of the variance in the instrumental GMST over the period 1870-2017 is explained by this model, and in particular all features of the 1998 -- 2015 hiatus, including its death. While the more prominent pauses during 1870 -- 1915 and 1940 -- 1970 can be attributed to clustering in time of strong volcanic eruptions, the recent hiatus is an unremarkable phenomenon that is attributed to ENSO and a small contribution from solar activity.

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

Water borne pathogens present a threat to human health and their disinfection from water poses a challenge, prompting search for newer methods and newer materials. Disinfection of Gram-negative bacterium Escherichia coli and Gram-positive coccal bacterium Staphylococcus aureus in aqueous matrix was achieved within 60 and 90 minutes respectively at 35⁰C using solar-photocatalysis mediated by sonochemically synthesized Ag@ZnO core-shell nanoparticles. The efficiency of the process increased with increase in temperature and at 55⁰C the disinfection could be achieved in 45 and 60 min respectively for the two bacteria. A new ultrasound assisted chemical precipitation technique was used for the synthesis of Ag@ZnO core-shell nanoparticles. The characteristics of the synthesized material were established using physical techniques. The material remained stable even at 400o C. Disinfection efficiency of the Ag@ZnO core-shell nanoparticles was confirmed in case of real world water samples from pond, river, municipal tap and was found to be better than that of pure ZnO and TiO2 (Degussa P25). When the nanoparticle based catalyst was recycled and reused for subsequent disinfection experiments, its efficiency did not change remarkably even after three cycles. The sonochemically synthesized Ag@ZnO core-shell nanoparticles have a good potential for application in solar photocatalytic disinfection of water borne pathogens.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

This article discusses a focused study on visualizing the flow patterns in a two-phase pulsating heat pipe (PHP) using Fe₃O₄/water as the working fluid at 3 V/V% concentration. The research also aims to meticulously examine phase change phenomena in the heating section, particularly focusing on bubble formation and expansion processes. A high-speed video camera was utilized to capture dynamic insights into the behavior of the Fe₃O₄/water mixture. Based on the findings, a straightforward model was developed to explain bubble generation and growth in the mixture, serving as a useful reference for future PHP designs and optimizations. Visual observations also noted the stable nature of the Fe₃O₄/water nanofluid over a four-day period, confirming its consistency throughout the experiments. Moreover, the impact of heat load variation on the evaporator section was assessed using controlled heat inputs ranging from 10 to 80 Watts. Observations on the arrangement of slugs and plugs at a 50% filling ratio revealed interesting self-adjusting flow patterns in response to increasing heat inputs, providing valuable insights into PHP operational dynamics. Notably, the oscillatory flow behavior of Fe₃O₄/water, the chosen working fluid, exhibited greater activity in comparison to water. This distinctive flow behavior contributed to achieving heightened thermal performance efficiency for the Fe₃O₄/water system, attributed to its faster attainment of the annular flow condition.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, researchers developed efficient aqueous nanofluid conductors. Carbon nanotubes (CNTs) are widely studied to reach efficient, stable, low-cost and environmentally-friendly aqueous-nanofluids. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain literature mechanisms behind improvement. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluids as desired.

Parkinson’s disease (PD) is the second-most common neurodegenerative disorder worldwide and is diagnosed based upon motor impairments. Non-motor symptoms are well-recognized in PD, and peripheral neuropathy is a frequent but poorly appreciated non-motor sign. Study of how the central and peripheral sensory systems are affected can contribute to the development of targeted therapies and deepen the understanding of the pathophysiology of PD. Although the cause of sporadic PD is unknown, chronic exposure to the pesticide rotenone in humans increases the risk of development of PD. Here, we aimed to investigate whether peripheral neuropathy is present in a traditional model of PD. Mice receiving intrastriatal rotenone showed greatly reduced dopamine terminals in the striatum and reduction in tyrosine hydroxylase-positive neurons in the Substantia nigra pars compacta and developed progressive motor impairments in hindlimb stepping and rotarod but no change in spontaneous activity. Interestingly, repeated testing using gold-standard protocols showed no change in gut motility, a well-known non-motor symptom of PD. Importantly, we did not observe any change in heat, cold, or touch sensitivity, again based upon repeated testing with well-validated protocols that were statistically well-powered. Therefore, this traditional model fails to replicate PD, and our data again reiterate the importance of the periphery to the disorder that is PD.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Designing high-voltage underground transmission lines poses complex challenges in heat management, trench optimization, and determining cable ampacity. This article introduces an innovative proposal that focuses on adjusting the dimensions of the thermal backfill as a primary strategy to enhance ampacity compared to the traditional approach of increasing the cross-sectional area of the cable core. The methodology employs a particle swarm optimization (PSO) technique with adaptive penalization, restart strategies, and parameter self-adaptation implemented in MATLAB. The objective of this approach is to provide more efficient solutions than traditional MATLAB PSO, demonstrating improved convergence and more accurate results with a success probability of 66.1\%. Although traditional PSO is 81\% faster, the proposed PSO stands out for its precision. Additionally, the incorporation of thermal backfill results in an 18.45\% increase in cable ampacity. Variations in the thermal resistivity of the soil, backfill, and ambient temperature are highlighted as sensitive factors affecting ampacity and backfill dimensions. This method is presented as a crucial tool in the early stages of the project and underground installation in operation with maximum ampacity, contributing to the continuous improvement of energy efficiency.

This paper presents a comprehensive study on the application and optimization of automotive thermoelectric generators (ATEGs), focusing on the crucial role of heat exchangers in enhancing energy conversion efficiency. Recognizing the substantial waste of thermal energy in internal combustion engines, our research delves into the potential of TEGs to convert engine waste heat into electrical energy, thereby improving fuel efficiency and reducing environmental impact. We meticulously analyze various heat exchanger designs, assessing their influence on the TEG's output power under different exhaust gas flow rates and temperatures. Furthermore, we explore the impact of TEG material properties on the overall energy conversion effectiveness. Our findings reveal that specific heat exchanger designs significantly enhance the efficiency of waste gas heat exchange, leading to an improved performance of the TEG system. We also highlight the importance of thermal insulation in maximizing TEG output. This study not only contributes to the ongoing efforts to develop more sustainable and efficient vehicles but also provides valuable insights into the practical application of thermoelectric technology in automotive engineering. Through this research, we aim to pave the way for more environmentally friendly transportation solutions, aligning with global efforts to reduce fossil fuel dependence and mitigate environmental pollution.

Indoor comfort is a critical determinant of the holistic educational experience, significantly influencing the well-being, concentration, and performance of students within the confines of school environments. Despite the widespread implementation of heating, ventilation, and air conditioning (HVAC) systems in educational institutions, achieving satisfactory thermal conditions, acceptable acoustics, and optimal daylight levels for occupants continues to pose a considerable challenge. In this review, we specifically delves into the parameters characterizing Italian school environments, recognizing their direct impact on students’learning and concentration. The primary objectives of this review are conducting a thorough examination of the current acustic conditions in Italian schools. The initial phase of our search strategy involved retrieving data from key databases, namely, Scopus, Web of Science, ScienceDirect, PubMed, and Google Scholar. Following the elimination of duplicate articles (n = 289), a total of 135 distinct papers remained for analysis. A critical review of the existing literature is presented based on these criteria, offering guidelines and recommendations for forthcoming studies. The critical review underscores various shortcomings in the current design, deployment, and documentation of multi-domain studies, signaling the need for enhanced quality in future research efforts.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

The feasibility of recovering bioactive antioxidants from Phyllantus emblica leaves using ethanol -water mixture (0 – 100%) and heat-assisted extraction technology (HAE-T) was investigated in this present study. To this effect, the process parameter of operating temperature (OT: 30 -50 oC), solid -to-liquid ratio (S:L: 1:20 - 1:60 g/mL) and extraction time (ET: 45 - 180 min) were investigated on the extract total phenolic content (TPC, mg GAE/g d.w), yield (EY, %) and antioxidant activity (μM AAE/g d.w) by employing the Box-Behnken experimental design (BBD) available in response surface methodology (RSM). Multi-objective process optimization using the desirability function algorithm to determine set of process variables that simultaneously optimize process responses of TPC, EY and AA was also investigated. The recovery process was thereafter modeled with BBD-RSM and multi gene genetic programming (MGGP) algorithm and model reliability assessment via Monte Carlo simulation were conducted for the best performing set of models for predicting TPC, EY and AA values. The HPLC characterization of the recovered extract was carried out to ascertain the phenolic compound constituents of the Phyllantus emblica leaf extract. The 50% ethanol solution was found to be the best for the optimal extraction of antioxidants from Phyllantus emblica leaves. The HAE-T was suitable for recovering bioactive extract from Phyllantus emblica leaves and investigated process parameters have impacts on the recovery process. The process parameters that simultaneously gave the optimum EY of 21.6565%, TPC of 67.116 mg GAE/g and AA of 3.68583 µM AAE/g were OT of 41.61 oC, S:L of 1:60 g/mL and ET of 180 min. The HPLC extract profiling revealed that the bioactive constituents present in the recovered extract were betulinic acid, gallic acid, chlorogenic acid, caffeic acid, ellagic acid, and ferulic acid. Both the developed BBD-RSM and evolved MGGP-based models predicted the observed process response of TPC, EY and AA satisfactorily with BBD-RSM models marginally better in their predictions. The reliability results showed that the BBD-RSM models predicted TPC, EY and AA values with high certainty of 99.985%, 97.569% and 98.661%, respectively.

Key thermophysical properties necessary for the successful design and use of CoCrFeNi alloy in thermophysical applications have been measured experimentally, and the results have been compared with literature values and results previously obtained for commercial Ni-Cr alloys and equiatomic CoCrFeNi alloy. In particular, the thermal diffusivity, coefficient of thermal expansion (CTE), and specific heat capacity were measured for the as-cast and homogenized equiatomic CoCrFeNi alloy over a temperature range allowing the thermal conductivity to be calculated up to 1173 K. The thermal conductivity and thermal diffusivity of the equiatomic CoCrFeNi alloy were found to deviate from monotonic behavior in the temperature range from 773 to 1100 K. Such a deviation was previously observed in the behavior of the temperature dependence of CTE and specific heat capacity of the equiatomic CoCrFeNi alloy. The non-linear behavior is primarily the result of order/disorder phenomena for the as-cast and homogenized sample, as well as additionally for the as-cast sample, non-equilibrium solidification under arc melting conditions. The measured data of thermophysical properties are provided for thermally differently treated samples, and it is shown that there is a difference in the behavior of the temperature dependences of CTE, thermal diffusivity, and heat capacity.

In recent years, in order to serve as effective solutions to outdoor human thermal environments under the influence of urban heat islands, adaptation measures such as awnings, louvers, directional reflective materials, mist sprays, and evaporative materials have been developed. In this study, a simplified evaluation framework for adaptation measures to urban heat islands is examined. Adaptation measures to urban heat islands are classified into the following three categories; measures to reduce solar radiation incident on the human body, measures to control and cool ground and wall surface temperature, and measures to control and cool air temperature and human body. Case studies are conducted to evaluate the effects of the implementation of cool water circulation sunshade and to examine the adverse effects of cool pavements on the human thermal environment, in addition to the effects of mist sprays on the human body. The effect of the sunshade, watering road, and mist spray, which are typical adaptation measures to urban heat islands, on the human thermal environment was estimated using Wet Bulb Globe Temperature (WBGT) as an indicator for heat stroke prevention and Standard New Effective Temperature (SET*) as an indicator for thermal comfort assessment.

The effect of high temperature (HT) stress on nicotine biosynthesis in Nicotiana attenuata was examined. Nicotine content was measured in mature leaves, young sink leaves and in roots from well-watered plants grown at 25 °C as controls and from plants exposed to 38 °C and 43 °C temperatures applied for 24, 48, 72 and 96-hr duration. At 38 °C, all leaf nicotine levels were significantly less than control plants for up to 72-hr exposure but rose sharply thereafter to levels significantly greater than controls with 96-hr exposure. In contrast, plants exposed to 43 °C never exhibited a reduction in leaf nicotine content and showed a significant increase in content with just 48-hr exposure. When radioactive 11CO2 was administered to plants, HT stress significantly reduced fixation. Furthermore, radiocarbon flux analysis revealed that ‘new’ C partitioning (as 11C) into the [11C]-amino acid pool was significantly reduced with HT stress as were yields of [11C]-aspartic acid, an important amino acid in nicotine biosynthesis, and its beta-amido counterpart [11C]-asparagine significantly reduced. In contrast, [12C]-aspartic acid levels appeared unaffected at 38 °C but were significantly elevated at 43 °C relative to controls. Additionally, [12C]-asparagine levels were significantly elevated at both stress temperatures. Finally, leaf total soluble protein (TSP) was reduced 39% with long exposures to both stress temperatures. However, Ribulose-1,5-bisphosphate carboxylase/oxygenase (Rubisco) which was 41% TSP appeared unaffected by HT stress. Altogether, these results support the theory that plant proteins other than Rubisco degrade at elevated temperatures freeing up essential amino acids supporting the nicotine biosynthetic machinery, and while feedback might downregulate de novo amino acid synthesis from ‘new’ C resources, more than likely plant C/N rebalancing caused by HT reductions in C input restricted N uptake, which in turn, limited this process.

Ever since oil was discovered in the Persian Gulf Region in the 1920s, the oil and gas industries have been dominant in the area. These countries are responsible for generating approximately 35 percent of the world's natural gas and 25 percent of its crude oil, making them the largest crude oil producers globally. The release of carbon dioxide (CO2) into the atmosphere is directly linked to the use of fossil fuels. CO2 accounts for 58.8 percent of all greenhouse gas emissions caused by human activities and has a detrimental impact on urban residents through the urban heat island effect. A significant portion of these emissions can be attributed to residential buildings. Some nations exacerbate the problem by relying excessively on fossil fuels. Oil-rich countries provide energy subsidies to the public in order to lower energy costs for their citizens. However, this policy can have negative consequences, including wasteful energy usage in countries like Iran.

CO2 is widely used in the prevention and control of coal spontaneous combustion. In this manuscript, three low-rank coals with different metamorphic degrees were selected as the research objects. The temperature-programmed experiments, in-situ infrared cooling experiments, simulation of competitive adsorption of CO2 and O2 in coal pores, and simulation study of CO2 inhibition of coal oxygen composite reaction were used to obtain the role and effect of CO2 in preventing oxygen adsorption in coal at low-temperature oxidation stage. It is concluded that CO2 can displace the O2 near the pore wall to physically prevent the adsorption of O2. Through the change law of heating rate and kinetic analysis, it is found that CO2 can increase its activation energy by 5.3%-108.3% during the slow heating stage of coal, and reduce its heating rate. At around 120°C, coal loses the protective effect of CO2. From the changes of functional groups, it can be seen that when coal is cooled in CO2 atmosphere, mainly pyrolysis and condensation reactions occur due to the lack of O2. In addition, CO2 can also inhibit the chain reaction of coal's chemical adsorption of oxygen. This work provides a theoretical basis for CO2 prevention and control of coal spontaneous combustion.

The multifarious internal workings of organisms are difficult to reconcile with a single feature defining a state of ‘being alive’. Indeed, definitions of life rely on emergent properties (growth, capacity to evolve, agency) only symptomatic of intrinsic functioning. Empirical studies demonstrate that biomolecules including ratcheting/rotating enzymes, ribozymes and pigment molecules undergo repetitive conformation state changes driven by energy absorption, excitation and relaxation. They exhibit disparate structures, but govern processes relying on directional physical motion (DNA transcription, translation, ATP synthesis, cytoskeleton transport, photosynthetic resonance energy transfer) and share the principle of repetitive uniplanar conformation changes driven by thermodynamic gradients, producing dependable unidirectional motion: ‘heat engines’ exploiting thermodynamic disequilibria to perform work. Recognition that disparate biological molecules share a heat engine principle governing directional motion, working in self-regulating networks, allows a mechanistic definition: life is a self-regulating process whereby matter undergoes cyclic, uniplanar conformation state changes that convert thermodynamic disequilibria into directed motion, performing work that locally reduces entropy. ‘Living things’ are structures including autonomous networks of units operating on the heat engine principle. Death is loss of integrated heat engine function. These principles are independent of any specific chemical environment, and can be applied to other biospheres.

The present paper contains data on the density (ρ), sound velocity (u), specific heat capacity (c_p ) of the mixture of N,N-dimethylformamide + 1-butanol (DMF + BuOH) determined in the entire concentration range of solution and in the temperature range: (293.15–318.15) K. The analysis of thermodynamic functions such as isobaric molar expansion, isentropic and isothermal molar compression, isobaric and isochoric molar heat capacity, as well as their excess functions (〖 E〗_(p,m)^E,〖 K〗_(S,m)^E,〖 K〗_(T,m)^E,〖 C〗_"p,m" ^E,〖 C〗_"V,m" ^E) and also V_m^E was undertaken. The analysis of changes in the physicochemical quantities was based on consideration of the system in an aspect of intermolecular interactions with resulting changes in the mixture structure. The results available in the literature are confusing during the analysis and became the reason for our decision to thoroughly examine the system. What is more, for a system whose components are widely used, there is no information in the literature regarding the heat capacity of the tested mixture, which was also achieved and presented in this publication. The conclusions drawn from so many data allow us to approximate and understand the changes that occur in the structure of the system due to repeatability and consistency of the obtained results

Forestry workers play a crucial role in implementing forest management programs, but their outdoor work exposes them to rising temperatures caused by global climate change, which poses potential health risks related to heat. This study focuses on Indonesian forestry workers and examines the relationship between their knowledge of heat-related issues, risk perception, and precautionary behavior in dealing with increasing workplace heat exposure. Developing effective precautionary behavior is essential for preventing heat-related health disorders and promoting health protection programs. To facilitate a comprehensive comparison of the three variables, interviews were conducted with two groups of outdoor workers, comprising 210 forestry workers and 215 paddy farmers. The findings indicate that increasing knowledge about heat-related issues promotes precautionary behavior, and risk perception acts as a mediator between knowledge and behavior. Additionally, the study highlights that the emotion of "dread" intensifies perceived risk and predicts positive behavior change. To enhance heat-related knowledge, exploring the potential use of a "fear" tone is important. In conclusion, comprehensive strategies need to be implemented to promote precautionary behavior among vulnerable forestry workers, particularly manual laborers.

The solar water heater must be integrated into future residential buildings as the main energy source, which will subsequently reduce the energy cost of water heating. An original configuration for efficient Domestic Hot Water "DHW" storage tank is developed and experimentally evaluated under Saharan climate. This novel DHW configuration includes a hybrid (solar and electric) energy system with a flat plate solar collector coupled with an electric heater. Additionally, phase change material "PCM" mixture that is composed of paraffin wax and animal fat with a melting temperature between 35.58°C and 62.58°C and latent heat between 180 and 210 kJ/kg is integrated into this novel tank configuration. The experimental results indicated that hot water production by using latent heat storage could be economically attractive. In this proposed configuration, one liter of hot water may cost around 0.1362 DZD/liter (i.e., 0.00096 US$/liter) compared to 0.4431 DZD/liter for the conventional water heater, an average energy cost savings of 69.26%. On a yearly basis, the average energy cost savings may reach up to 80.25% if optimal tilt for the solar collector is adopted on a monthly basis. The flat plate collector may be vulnerable to convective heat transfer, and therefore, other solar collectors such as vacuum tube collectors may provide enhanced energy performance.

The dynamic effects observed in collisions represent a specific area of high-energy interaction located at the boundary of mechanics, hydrodynamics, shock wave physics, and alternating high-pressure regions. The paper shows that in the volume of a solid metal body, as a result of dynamic alloying by a high-speed stream of powder particles in the super-deep penetration mode (SDP), fibre structures of altering material arise, forming the framework of the composite material. The stream of powder particles in the metal obstacle following the path of least resistance and the impact of shock waves on particles results in a volumetric framework from the products of interaction between the injected and matrix materials. When using SDP, defective structural elements (channelled) - germs of reinforcing fibres arise. At the subsequent heat treatment, there is an intensive diffusion. The growth process of reinforcing fibres shifts to higher temperatures (as compared to the standard mode), leading to an increase in the bending strength of the fibre material up to 13 times for high-speed tool W6Mo5Cr4V2 steel. As a result of the completion of the growth of reinforcing fibres in the volume of the W6Mo5Cr4V2 steel, the material's bending strength in 1.2 times is realised. Simultaneously, it provides an increase of wear resistance 1.7-1.8 times.

During type 1 diabetes mellitus (T1DM) development, beta-cells undergo intense endoplasmic reticulum (ER) stress that could result in apoptosis through the failure of adaptation to the unfolded protein response (UPR). Islet transplantation is considered an attractive alternative among beta-cell replacement therapies for T1DM. To avoid the loss of beta-cells that will jeopardize the transplant´s outcome, several strategies are being studied. We have previously shown that prolactin induces protection against pro-inflammatory cytokines and redox imbalance-induced beta-cell death by increasing heat shock protein B1 (HSPB1) levels. Since the role of HSPB1 in beta cells has not been deeply studied, we investigated the mechanisms involved in unbalanced protein homeostasis caused by intense ER stress and overload of the proteasomal protein degradation pathway. We tested whether HSPB1-mediated cytoprotective effects involved UPR modulation and improvement of protein degradation via the ubiquitin-proteasome system. We demonstrated that increased levels of HSPB1: attenuated levels of pro-apoptotic proteins like CHOP and BIM, increased protein ubiquitination and the speed of proteasomal protein degradation. Our data showed that HSPB1 induced resistance to proteotoxic stress and thus enhanced cell survival via an increase in beta-cell proteolytic capacity. These results could contribute to generate strategies aiming at optimization of beta-cell replacement therapies.

The effect of thermal radiation on the two – dimensional, steady-state, conjugate heat transfer from a circular cylinder with an internal heat source in steady laminar crossflow is investigated in this work. P₀ (Rosseland) and P₁ approximations were used to model the radiative transfer. The mathematical model equations were solved numerically. Qualitatively, P₀ and P₁ approximations show the same effect of thermal radiation on conjugate heat transfer; the increase in the radiation – conduction parameter decreases the cylinder surface temperature and increases the heat transfer rate. Quantitatively, there are significant differences between the results provided by the two approximations.

Neurological complications of infection by the mosquito-borne Zika virus (ZIKV) include Guillain-Barré syndrome (GBS), an acute inflammatory demyelinating polyneuritis. GBS was first associated with recent ZIKV epidemics caused by the emergence of ZIKV Asian lineage in South Pacific. Here, we hypothesize that ZIKV-associated GBS relates to a molecular mimicry between viral envelope E (E) protein and neural proteins involved in GBS. Analysis of ZIKV epidemic strains showed that glycan loop (GL) region of the E protein includes an IVNDT motif which is conserved in voltage-dependent L-type calcium channel subunit alpha-1C (Cav1.2) and Heat Shock 70 kDa protein 12A (HSP70 12A). Both VSCC-alpha 1C and HSP70 12A belong to protein families which have been associated with neurological autoimmune diseases in central nervous system. The purpose of our in silico analysis is to point out that IVNDT motif of ZIKV E-GL region should be taken in consideration for the development of safe and effective anti-Zika vaccines by precluding the possibility of adverse neurologic events including autoimmune diseases such as GBS.

In the last decades farm animals kept in confined and mechanically ventilated livestock buildings are increasingly confronted with heat stress (HS) due to global warming. These adverse conditions cause a depression of animal health and welfare and a reduction of the performance up to an increase of the mortality. To facilitate sound management decisions, livestock farmers need relevant arguments, which quantify the expected economic risk and the corresponding uncertainty. The economic risk was determined for the pig fattening sector based on the probability of HS and the calculated decrease in the gross margin. The model calculation for confined livestock buildings showed, that HS indices calculated by easily available meteorological parameters can be used for assessment quantification of indoor HS, which is so far difficult to determine. These weather-related HS indices can be applied not only for an economic risk assessment but also for a weather-index based insurance for livestock farms. Based on the temporal trend between 1981 and 2017, a simple model was derived to assess the likelihood of HS for 2020 and 2030. Due to global warming, the return period for a 90-percentile HS index is reduced from 10 years in 2020 to 3-4 years in 2030. The economic impact of HS on livestock farms was calculated by the relationship between an HS index based on the temperature-humidity index (THI) and the reduction of the gross margin. From the likelihood of the HS and this economic impact function, the probability of the economic risk could be determined. The reduction of the gross margin for a 10 year return period was determined for 1980 with 0.27 € per year and animal place and increased by the 20-fold to 5.13 € per year and animal place in 2030.

In the steel industries, workers are exposed to heat and ambient thermal stresses on a daily basis, leading to discomfort and limited performance. In this study, the main purpose is to investigate the effect of climate heat stress on the rate of accidents in the workplace for workers for 5 consecutive years. The data of this study were received without any sampling through the HSE Center for Steel Industry and meteorological data from 2015 to 2019 from Isfahan Meteorological station. The daily number of casualties among workers in the steel industry during 2015-2019 by adjusting seasonal patterns, months, effects of the day of the week and other meteorological factors on the average daily temperature using the studied model has a decreasing effect. Eviews software (version 8) was used to model and investigate the relationship between events and meteorological variables. The mean temperature was at least 40.2-2 and at most 70.34 ° C, respectively. In the time-series study for the main model, the number of accidents shows a direct relationship with the average temperature and wind speed. Climatic indices of humidity and rainfall have the least impact on accidents compared to temperature and wind speed. A strong correlation was shown between the increase in average ambient temperature and the rate of accidents over the past 5 years. Given the fundamental differences in studies of environmental exposure and wind speed over heat stress, further analysis in workers should be considered.

Based on electromagnetic heat transfer and metal phase transformation co-simulations, we modeled an AISI 1045 specimen under high-frequency heat treatment. Hardening zone predictions were confirmed through cooling and metal phase transformation simulations after obtaining the results from electromagnetic heat transfer simulations. The cooling process was modeled by applying the cooling coefficient of the cooling water in the same way as the actual heat-treatment process. To obtain the current flowing through the coil during high-frequency induction heating, the voltage was measured and applied using the resistance–inductance–capacitance circuit calculation method. Experimental and simulated results of the heating temperature and curing depth of an AISI 1045 specimen with a carbon content of 0.45% were compared; the comparison indicated good agreement between the two. Using the simulation results, we established a method for obtaining the current flowing through the induction coil for predicting the extent and depth of the hardening zone during high-frequency induction heat treatment.

We construct a microscopic model to study discrete randomness in bistable systems coupled to an environment comprising many degrees of freedom. A quartic double well is bilinearly coupled to a finite number N of harmonic oscillators. Solving the time-reversal invariant Hamiltonian equations of motion numerically, we show that for N=1, the system exhibits a transition with increasing coupling strength from integrable to chaotic motion, following the KAM scenario. Raising N to values of the order of 10 and higher, the dynamics crosses over to a quasi-relaxation, approaching either one of the stable equilibria at the two minima of the potential. We corroborate the irreversibility of this relaxation on other characteristic timescales of the system by recording the time dependences of autocorrelation, partial entropy, and the frequency of jumps between the wells as functions of N and other parameters. Preparing the central system in the unstable equilibrium at the top of the barrier and the bath in a random initial state drawn from a Gaussian distribution, symmetric under spatial reflection, we demonstrate that the decision whether to relax into the left or the right well is determined reproducibly by residual asymmetries in the initial positions and momenta of the bath oscillators. This result reconciles the randomness and spontaneous symmetry breaking of the asymptotic state with the conservation of entropy under canonical transformations and the manifest symmetry of potential and initial condition of the bistable system.

Diurnal and seasonal changes of abiotic environmental factors shape plant performance and distribution. Changes of growth temperature and light intensity may vary significantly on a diurnal, but also on a weekly or seasonal scale. Hence, acclimation to a changing temperature and light regime is essential for plant survival and propagation. In the present study, we analyzed photosynthetic CO₂ assimilation and metabolic regulation of the central carbohydrate metabolism in two natural accessions of Arabidopsis thaliana originating from Russia and south Italy during exposure to heat and a combination of heat and high light. Our findings indicate that it is hardly possible to predict photosynthetic capacities to fix CO₂ under combined stress from single stress experiments. Further, capacities of hexose phosphorylation were found to be significantly lower in the Italian than in the Russian accession which could explain an inverted sucrose-to-hexose ratio. Together with the finding of significantly stronger accumulation of anthocyanins under heat/high light these observations indicate a central role of hexokinase activity in stabilization of photosynthetic capacities within a changing environment.

The meshless Petrov-Galerkin (MLPG) method is developed to analyse 2-D problems for flexoelectricity and thermoelectricity. Both problems are multiphysical and scale dependent. The size-effect is considered by the strain- and electric field-gradients in the flexoelecricity and higher-grade heat flux in the thermoelectricity. The variational principle is applied to de-rive the governing equations considered constitutive equations. The order of derivatives in governing equations is higher than in equations obtained from classical theory. The coupled governing partial differential equations (PDE) are satisfied in a local weak-form on small fic-titious subdomains with a simple test function. Physical fields are approximated by the mov-ing least-squares (MLS) scheme. Applying the spatial approximations in local integral equa-tions a system of algebraic is obtained for the nodal unknowns.

Imaging techniques such as computed tomographies (CT) play a major role in clinical imaging and diagnosis of malignant lesions. In recent years, spectral CT has emerged in the field of computed tomographies, utilizing detailed information from extracted spectral parameters of the specimen. Metal nanoparticle platforms enable effective payload delivery for this technique. Due to the possibility of surface modification, metal nanoparticles are predestined to facilitate molecular tumor targeting. In this work, we demonstrate the feasibility of anti-plasma membrane Heat shock protein 70 functionalized gold nanoparticles (AuNPs) for tumor specific multimodal imaging. Membrane-associated Hsp70 is exclusively presented on the plasma membrane of malignant cells of multiple tumor entities, but not on corresponding normal tissue cells, predestining this target epitope for tumor-selective in vivo targeting. In vitro microscopical analysis revealed the presence of cmHsp70.1-AuNP in the cytosol of tumor cell lines, being internalized via the endosomal-lysosomal pathway. In tumor bearing mice the biodistribution as well as the intratumorally enrichment of AuNP were examined 24h after i.v. application, in vivo. In parallel to spectral CT analysis, histological analysis confirmed the presence of tumor cells. In contrast to control NP, a significant enrichment of cmHsp70.1-AuNPs has been detected selectively in tumors of different preclinical mouse models. Furthermore, the biodistribution of AuNP, following i.v. injection, was analyzed by a machine-learning approach on digitalized slides. In summary, utilizing mHsp70 on tumor cells for guidance of cmHsp70.1 antibody functionalized nanoparticles enables sufficient enrichment and uniform distribution of AuNPs in mHsp70-expressing tumor cells, adequate for various microscopical imaging techniques and spectral-CT-based tumor delineation, in vivo.

A universally applicable method for the prediction of the isobaric heat capacities of the liquid and solid phase of molecules at 298.15 K is presented, derived from their “true” volume. The molecules’ “true” volume in A³ is calculated on the basis of their geometry-optimized structure and the Van-der-Waals radii of their constituting atoms by means of a fast numerical algorithm. Good linear correlations of the “true” volume of a large number of compounds encompassing all classes and sizes with their experimental liquid and solid heat capacities over a large range have been found, although noticeably distorted by intermolecular hydrogen-bond effects. To take account of these effects, the total amount of 1303 compounds with known experimental liquid heat capacities has been subdivided into three subsets consisting of 1102 hydroxy-group-free compounds, 164 monoalcohols/monoacids, and 36 polyalcohols/polyacids. The standard deviations for Cp(liq,298) were 20.7 J/mol/K for the OH-free compunds, 22.91 J/mol/K for the monoalcohols/monoacids and 16.03 J/mol/K for the polyols/polyacids. Analogously, 797 compounds with known solid heat capacities have been separated into a subset of 555 OH-free compounds, 123 monoalcohols/monoacids and 119 polyols/polyacids. The standard deviations for Cp(sol,298) were calculated to 23.14 J/mol/K for the first, 21.62 J/mol/K for the second, and 19.75 J/mol/K for the last subset. A discussion of structural and intermolecular effects influencing the heat capacities as well as of some special classes, in particular hydrocarbons, ionic liquids, siloxanes and metallocenes, has been given. In addition, the present method has successfully been extended to enable the prediction of the temperature dependence of the solid and liquid heat capacities in the range between 250 and 350 K.

A non-Newtonian fluid model is used to investigate the two-dimensional pulsatile blood flow through a tapered artery with a stenosis. The mixed convection effects of heat and mass transfer are also taken into account. By applying non-dimensionalization and radial coordinate transformation, we simplify the system in a tube. Under the finite difference scheme, numerical solutions are calculated for velocity, temperature concentration, resistance, impedance, wall shear stress and shearing stress at the stenosis throat. Finally, Quantitative analysis is carried out.

Resistant cancer often shows a particular secretory trait such as heat shock proteins (HSPs) and extracellular vesicles (EVs), including exosomes and oncosomes surrounded by lipid bilayers. Lipoproteins are biochemical assemblies that transport hydrophobic lipid (a.k.a. fat) molecules in body fluid and are composed of a single-layer phospholipid and cholesterol outer shell, lipids molecules within the particles, and apolipoproteins embedded in the membrane. However, lipoprotein storage and secretion by cancer cells have not well-investigated yet. We found lipoproteins were stored and abundantly secreted by neuroendocrine, castration-resistant prostate cancer (NEPC / CRPC) cells but barely secreted by colon cancer cells and oral squamous cell carcinoma (OSCC) cells. In addition, large EVs (approx. 300 nm diameter) and potential oncosomes were released by CRPC and OSCC cells. Proteomics revealed that CRPC cells secreted EVs enriched with tetraspanins and extracellular matrices which were reduced upon heat shock stress and alternatively lipoproteins and HSPs were secreted upon stress. Heat shock stress triggered secretion of lipoprotein-EV complexes that contained apolipoprotein A, B, C and E. These data suggested that vesicular assembly composed of EVs and lipoproteins enriched with cholesterols and phospholipids may be stored in resistant cancer cells but released upon cell stress that is increased in cancer therapies.

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

In this paper, an improved system to efficiently utilize the low-temperature waste heat (WHUS) from the flue gas of coal-fired power plants is proposed based on heat cascade. The essence of the proposed system is that the waste heat of exhausted flue gas is not only used to preheat air for assisting coal combustion as usual but also to heat up feedwater and the low-pressure steam extraction. Preheated by both the exhaust flue gas in the boiler island and the low-pressure steam extraction in the turbine island, thereby part of the flue gas heat in the air preheater can be saved and introduced to heat the feedwater and the high-temperature condensed water. Consequently, part of the high-pressure steam is saved for further expansion in the steam turbine, which obtains additional net power output. Based on the design data of a typical 1000 MW ultra-supercritical coal-fired power plant in China, in-depth analysis of the energy-saving characteristics of the optimized WHUS and the conventional WHUS is conducted. When the optimized WHUS is adopted in a typical 1000 MW unit, net power output increases by 19.51 MW, exergy efficiency improves to 45.46%, and net annual revenue reaches 4.741 million USD. In terms of the conventional WHUS, these aforementioned performance parameters are only 5.83 MW, 44.80% and 1.244 million USD, respectively. The research of this paper can provide a feasible energy-saving option for coal-fired power plants.

In this work, we investigated the effects of heat treatment on the microstructure, hydrogen storage characteristics and corrosion rate of a Ti₃₄V₄₀Cr₂₄Fe₂ alloy. The arc melted alloy was divided into three samples, two of which were separately quartz-sealed under vacuum and heated to 1000 °C for 1 h; one of these samples was quenched and the other furnace cooled to ambient temperature. The crystal structures of the samples were studied via X-ray diffractometry and scanning electron microscopy. Absorption/desorption characteristics were investigated using a Sievert apparatus. Potentiostat corrosion tests on the alloys were performed using an AutoLab^® corrosion test apparatus and electrochemical cell. All samples exhibited a mixture of body-center-cubic (BCC) and Laves phase structures. The corrosion rate, maximum absorption, and useful capacities increased after both heat treatments. The annealed sample had the highest absorption and reversible capacity. The plateau pressure of the as-cast alloy increased after quenching. The corrosion rate increased from 0.0004 mm/y in as-cast sample to 0.0009 mm/y after annealing and 0.0017 mm/y after quenching, due to a decrease in the Cr-content of the C14 phase.

In the past two decades the world experienced an exceptional number of unprecedented extreme weather events, some causing major human suffering and economic damage, such as the March 2012 heat event, which was called “Meteorological March Madness.” From the beginning of space era a correlation of solar flares with pressure changes in atmosphere within 2–3 days or even less was reported. In this study we wanted to test the possible relation of highly warm weather events in North-East America with Solar Energetic Particle (SEP) events. For this reason we compared ground temperatures T_M in Madison, Wisconsin, with energetic particle fluxes P measured by the EPAM instrument onboard the ACE spacecraft. In particular, we elaborated case events and the results of a statistical study of the SEP events related with the largest (Dst ≤ −150nT) Coronal Mass Ejection (CME)-induced geomagnetic storms, between with the years 1997–2015. The most striking result of our statistical analysis is a very significant positive correlation between the highest temperature increase_. ΔT_M and the time duration of the temperature increase ΔT_M (r = 0.8, p <0.001) at “winter times” ( r = 0.5, p , 0.01 for the whole sample of 26 SEP examined events). The time response of T_M to P was found to be in general short (a few days), but in the case of March 2015, during a gradual P8 increase, a cross-correlation test indicated highest c.c. within 1 day (p < 0.05). The March 2012 “meteorological anomaly” was elaborated in the case of South-East Europe, where, beside a period of strong winds and rainfall (6-13.3.2012), intense precipitation in North-East Greece (Alexandroupoli) were found to be correlated with distinct high energy flux enhancements. A rough theoretical interpretation is discussed for the space—atmospheric extreme weather relationship we found. However, much work should be done to achieve early warning of space weather dependent extreme meteorological events. Such future advances in understanding the relationships between space weather and extreme atmospheric events would improve atmospheric models and help people’s safety, health and life.

Lotions with or without 28% ascorbyl glucoside arginine complex (AGAC) were applied twice daily for 24 weeks in a double‐blind half‐face study of 27 Japanese females with solar lentigos (SLs). Pigmentation scores were evaluated using a photo‐scale and skin colors were assessed using a color difference meter and a Mexameter. Treatment with the test lotion elicited a significant decrease in pigment scores at 24 weeks compared to week 0; with a significant decrease in pigment scores at 24 weeks compared to the placebo lotion‐treated SLs. In the test lotion‐treated SLs; the L values and melanin index (MI) significantly (p<0.0001) increased and decreased; respectively; at 12 and 24 weeks of treatment compared to week 0. Comparisons of increased L (△L) values or decreased MI (△MI) values between test and placebo lotion‐treated SLs demonstrated that the test lotion‐treated SLs had significantly higher △L or △MI values than the placebo lotion‐treated SLs both at 12 and 24 weeks of treatment. The sum of our results strongly indicates that AGAC is distinctly effective in ameliorating the hyperpigmentation levels of SLs at a visibly recognizable level by the subjects without any hypo‐pigmenting effects or skin irritation.

In the field of adaptive building technologies, this research introduces the development of a self-regulating solar shading actuator, that utilizes the thermal shape memory effect. The study places its focus on addressing the actuator’s performance under diverse environmental conditions. Thermal simulations were carried out during the development of the individual components of the actuator and for the prediction of specific switching temperatures. The investigation includes an analysis of the sunshade’s response to varying environmental conditions, emphasizing its effectiveness on clear summer days and identifying challenges during overcast periods. The critical coordination between the solar collector and the shape memory alloy (SMA) wire is examined, shedding light on the impact of SMA temperature dynamics on the actuation performance. Through the integration of simulation data and real-world measurements, the study validates the thermal model for the solar collector, establishing the robustness of the system’s operation. This research work contributes significantly to the development of intelligent actuators and outlines the importance of validation of SMA-based applications under real conditions.

Although solar photovoltaic (PV) system costs have declined, capital cost remains a barrier to widespread adoption. Do-it-yourself (DIY) system designs can decrease costs by about 50% by reducing labor costs, but if not attached to a building structure demand ground penetration for conventional footings. This is not technically and economically feasible at all sites. To overcome these challenges, this study details systems designed to eliminate drilling holes and pouring concrete. Two different designs for both fixed tilt and variable tilt PV racking are investigated to assess their structural integrity, constructability, and economic cost when fabricated with a ballast-supported foundation. The ballast-supported foundations are analyzed for eight such systems by proposing two separate ballast designs: one for single line of post systems, and one for double line of post systems built on a 4-kW basis. The results of the analysis found that both designs are slightly more expensive than typical in-ground concrete systems by 25%, but the overall DIY systems costs remain economically advantageous. Sensitivity analyses are conducted to show how modifications to the dimensions including clearances and distances between gabions influence the weight of the system and thus change the economic value of the design, so users can trade dimensional freedom for cost-savings, and vice versa. Overall, all the wood-based PV racking system designs provide users with cost-effective and easy DIY alternatives to conventional metal racking, and the novel ballast systems presented provide more versatility for PV systems installations.

In recent years, advancements in rooftop solar panel technology have sparked a revolution in the electricity markets. This has given rise to a new concept of energy exchange - the ability for consumers and producers to trade localized energy. This concept has been made possible by the emergence of blockchain technology, which has gained significant traction in the energy markets. Its unique ability to facilitate peer-to-peer (P2P) energy transactions has made it a promising solution for the trilemma of scalability, security, and decentralization. However, while blockchain technology has shown great potential, it is still in its early stages of development and has yet to reach its full potential. To fully understand the potential of blockchain technology in P2P energy trading, it is important to explore the trilemma in depth. This study proposes a blockchain-based scalability solution, with a focus on P2P energy trade. This strategy is supported by empirical modeling, utilizing data gathered from a trial case study. The results of this study demonstrate that the suggested technique outperforms base layer models in terms of scalability, while still maintaining the essential elements of security and decentralization. This proposed solution not only has the potential to revolutionize the energy markets, but also has broader implications. By providing a more secure and decentralized platform for P2P energy trading, it has the potential to address issues of energy distribution inequality and promote the adoption of renewable energy. With blockchain technology, individuals and communities have the opportunity to take control of their energy usage and production, reducing their reliance on traditional centralized energy systems. This not only has the potential to lower energy costs for consumers, but also contributes to the overall goal of reducing carbon emissions and mitigating the effects of climate change. The combination of rooftop solar panel technology and blockchain applications has the potential to create a significant shift towards decentralized and sustainable energy systems. This will not only benefit individuals and communities, but also have a positive impact on the environment and the global energy market as a whole. However, for this transition to occur, it is crucial that governments and energy companies continue to support and invest in these advancements.

Modern electrical power systems integrate renewable generation, with solar generation being one of the pioneers worldwide. In Latin America, the greatest potential and development of solar generation is found in Chile through the National Electric System. However, its energy matrix faces a crisis of drought and reduction of emissions that limits hydroelectric generation and involves the definitive withdrawal of coal generation. The dispatch of these plants is carried out by the system operator, who uses a simplified mechanism, called “economic merit list” and which does not reflect the real costs of the plants to the damage of the operating and marginal cost of the system. This inefficient dispatch scheme fails to optimize the availability of stored gas and its use over time. Therefore, a real-time redispatch model is proposed that minimizes the operation cost function of the power plants, integrating the variable generation cost as a polynomial function of the net specific fuel consumption, adding gas volume stock restrictions and water reservoirs. In addition, the redispatch model uses an innovative "maximum dispatch power" restriction, which depends on the demand associated with the automatic load disconnection scheme due to low frequency. Finally, by testing real simulation cases, the redispatch model manages to optimize the operation and dispatch costs of power plants, allowing the technical barriers of the market to be broken down with the aim of integrating ancillary services in the short term, using the power reserves in primary (PFC), secondary (SCF), and tertiary (TCF) frequency control.

Bifacial PV modules have become the pervasive choice for utility-scale solar photovoltaic (PV) installations. Understanding bifacial PV performance for commercial deployments is, therefore, critically important. Although there have been studies on the modeling of Bifacial PV performance, to the best of our knowledge, the comprehensive integration of racking and mounting geometry for Bifacial PV performance simulation is yet to be reported. In this work, we modeled the racking and mounting geometry for a field-deployed operational PV array. We then applied optical ray-trace simulation to study the impact of those structures on array performance. The study reveals that the support structures have a considerable impact on the rear surface irradiance and overall bifacial PV performance, amounting to as much as 30% shading in certain situations. The work analyzes the impact of installation parameters such as tilt, height, and row spacing on the bifacial PV array’s performance. Thus, a novel holistic approach to studying the sensitivity of various installation parameters’ impact on bifacial PV array performance, with the racking and mounting structure’s geometry integrated, has been demonstrated through the work. This knowledge and its practice enables site-specific design optimization for utility-scale bifacial solar PV arrays and synergistic PV applications such as agrivoltaics and carports, where maximizing power generation is not necessarily the sole objective.

Energy demand and consumption in recent times have witnessed a rapid proliferation influenced by technological developments, increased population and economic growth. This has fuelled research trends in the domain of energy management employing tri-generation systems such as the combined cooling, heating and power (CCHP) systems. Furthermore, the incorporation of renewable energy, especially solar energy, to complement the thermal input by fossil fuels has facilitated the effectiveness and sustainability of CCHP systems. This study proposes a new approach to improve the overall efficiency of CCHP systems and compute the optimal design parameters in order to assist decision makers to identify the best geometrical configuration. A multi-objective optimization formulation of a solar-assisted CCHP system was adopted to maximize the net power, the exergy efficiency and minimize the CO2 emission using the greywolf optimization technique. In addition, the effects of the decision variables on the objective functions were analysed. The proposed optimization approach yielded 100 set of Pareto optimal solutions which would serve as options to the decision maker to make a selection in order to improve the performance of a solar-assisted CCHP system. This study demonstrates that the proposed approach is potentially suitable for the optimization of a solar-assisted CCHP system.

Sport centers are significant energy consumers. This article outlines the engineering design for a comprehensive energy performance upgrade of the indoor sport hall in Arkalochori, Greece, and presents the projected results. The indoor sport hall constitutes a major sport facility in the mainland of Crete, hosting a broad cluster of sport municipal activities and the official basketball games of the local team in the 2nd national category. Having being constructed in the mid ‘90s, the facility exhibits very low thermal performance, with considerably high U-factors for all constructive elements (from 4 to 5 W/m2∙K), still use of diesel oil for indoor space heating and domestic heat water production and ineffective, old lamps and luminaries covering the lighting needs of the facility. The energy performance upgrade of the indoor sport hall was holistically approached, through all possibly applicable passive and active measures: insulation of opaque surfaces and replacement of openings, installation of new stone wool panels, installation of heat pumps for indoor space conditioning, elimination of diesel oil for any final energy use, installation of a solar-combi system for domestic hot water production, upgrade of all indoor and outdoor lighting equipment, installation of solar tubes on the main sport hall roof for natural lighting and installation of a photovoltaic plant on the same roof for the compensation of the remaining electricity consumption. With the proposed measures, the indoor sport hall is upgraded to zero energy facility. The payback period of the investment was calculated at 26 years, on basis of the avoided energy resources procurement cost. This work has been funded by the Horizon 2020 project with the acronym “NESOI” and was awarded with the public award of the “Islands Gamechanger” competition of the NESOI project and the Clean Energy for EU Islands initiative.

One-Dimensional Solar Cell Capacitance Simulator (1D-SCAPS) and n-i-p planar configuration have been employed for the simulation of the caesium tin iodide (CsSnI₃)-based perovskite solar cell (PSC) with titanium (IV) oxide (TiO₂) and copper thiocyanate (CuSCN) as the electron and hole transport materials respectively. The results obtained for the initially modeled PSC compared well with similar devices in the literature but marred with high recombination rate. As such, the defect density in the CsSnI₃ absorber was varied from 10¹³ cm^-3 to 10¹⁷ cm^-3 and enriched with SnCl₂ (additive) and Br⁻(dopant) respectively. This strategy ensured a reduced concentration of Sn⁴⁺ vacancy (V_Sn) in the CsSnI₃ absorber with improved carrier lifetime and diffusion length beyond 0.05 ns and 1.1µm by a magnitude of the order of 10³ and 10² respectively for the enriched CsSnI₃ –based PSC. For the optimized PSC, we recorded V_OC=1.289 V, J_SC=32.60 mA.cm^-2, FF=83.56% and PCE=35.12%.

This article describes in detail the numerical modeling of a CZTS (copper zinc tin sulfide) based kesterite solar cell. The Solar Cell Capacitance Simulator -one-dimension (SCAPS-1D) software was used to simulate MO/CZTS/CdS/ZnO/FTO structured solar cells. The parameters of different photovoltaic thin-film solar cells are estimated and analyzed using numerical modeling. The effects of various parameters on the performance of the photovoltaic cell and the conversion efficiency are discussed. Since the response of the solar cell is also contingent on its internal physical mechanism, J-V characteristic measures are insufficient to characterize the behavior of a device. Different features, as well as different potential conditions, must be considered for simulation, disregarding the belief in the modeling of a solar cell. With a conversion efficiency of 25.72%, a fill factor of 83.75%, a short-circuit current of 32.96436 mA/cm2 and an open-circuit voltage of 0.64V, promising optimized results have been achieved. The findings will be useful in determining the feasibility of fabricating high-efficiency CZTS-based photovoltaic cells. The efficiency of a CZTS-based experimental solar cell is also discussed. First, the effects of experimentally developed CZTS solar cells are simulated in the SCAPS-1D environment. The experimental results are then compared to the SCAPS-1D simulated results. The conversion efficiency of an optimized system increases after cell parameters are optimized. Using one-dimensional SCAPS-1D software, the effect of system parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells is investigated. The proposed results will greatly assist engineers and researchers in determining the best method for optimizing solar cell efficiency, as well as in the development of efficient CZTS-based solar cells.

Based on measured astronomical position data of heavenly objects in the Solar System and other planetary systems, all bodies in space seem to move in some kind of elliptical motion with respect to each other. According to Kepler’s 1^st Law, “orbit of a planet with respect to the Sun is an ellipse, with the Sun at one of the two foci.” Orbit of the Moon with respect to Earth is also distinctly elliptical, but this ellipse has a varying eccentricity as the Moon comes closer to and goes farther away from the Earth in a harmonic style along a full cycle of this ellipse. In this paper, our research results are summarized, where it is first mathematically shown that the “distance between points around any two different circles in three dimensional space” is equivalent to the “distance of points around a vector ellipse to another fixed or moving point, as in two dimensional space”. What is done is equivalent to showing that bodies moving on two different circular orbits in space vector wise behave as if moving on an elliptical path with respect to each other, and virtually seeing each other as positioned at an instantaneously stationary point in space on their relative ecliptic plane, whether they are moving with the same angular velocity, or different but fixed angular velocities, or even with different and changing angular velocities with respect to their own centers of revolution. This mathematical revelation has the potential to lead to far reaching discoveries in physics, enabling more insight into forces of nature, with a formulation of a new fundamental model regarding the motions of bodies in the Universe, including the Sun, Planets, and Satellites in the Solar System and elsewhere, as well as at particle and subatomic level. Based on the demonstrated mathematical analysis, as they exhibit almost fixed elliptic orbits relative to one another over time, the assertion is made that the Sun, the Earth, and the Moon must each be revolving in their individual circular orbits of revolution in space. With this expectation, individual orbital parameters of the Sun, the Earth, and the Moon are calculated based on observed Earth to Sun and Earth to Moon distance data, also using analytical methods developed as part of this research to an approximation. This calculation and analysis process have revealed additional results aligned with observation, and this also supports our assertion that the Sun, the Earth, and the Moon must actually be revolving in individual circular orbits.

This paper contains a concise overview of the deployment of scattered solar power plants in Poland, mainly from the perspective of their communication networks, and how the recent development of the Polish 4G networks has a very positive impact for the performance of the whole monitoring system (production control and video-surveillance), with a special emphasis on video-analytics, due to its higher bandwidth demand. All the information will be shown from the point of view of the solar photovoltaics developer I+D Energías, and therefore it constitutes a real user’s experience.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

In order to reach the theoretical efficiency limits of lead-based metal halide perovskite solar cells, the voltage should be enhanced because it suffers from nonradiative recombination. Perovskite materials contain intrinsic defects that can act as Shockley-Read-Hall recombination centers. Several experimental and computational studies have characterized such defect states within the band gap. We give a systematic overview of compositional engineering by distinguishing the different defect reducing mechanisms. Doping effects are divided into influences on: (1) Crystallization; (2) Lattice properties. Incorporation of dopant influences the lattice properties by: (a) Lattice strain relaxation; (b) Chemical bonding enhancement; (c) Band gap tuning. The intrinsic lattice strain in undoped perovskite was shown to induce vacancy formation. The incorporation of smaller ions, such as Cl, F and Cd, increases the energy for vacancy formation. Zn doping is reported to induce strain relaxation but also to enhance the chemical bonding. The combination of computational studies using (DFT) calculations quantifying and qualifying the defect reducing propensities of different dopants with experimental studies is essential for deeper understanding and unraveling insights, such as the dynamics of iodine vacancies and the photochemistry of the iodine interstitials, and can eventually lead to a more rational approach in the search for optimal photovoltaic materials.

In light of climate changes, technological development and the use of renewable energy sources are considered very important nowadays, both in newly-designed structures and reconstructed historic building, resulting in the reduction of the commercial energy consumption and CO2 environmental emissions. This paper explores the possibilities of improving the energy efficiency of heritage sacred buildings by utilizing photovoltaic systems. As an exceptionally significant cultural good, the Cathedral of St. Michael the Archangel in Belgrade shall serve as a case study, with the aim of examining the methods of mounting photovoltaic (PV) panels, by taking into account the fact that the authenticity and the aesthetic value of this cultural monument must remain intact. A comparative analysis of the two options for installing PV panels on the southwestern roof of the church was performed using simulations in PVgis and PVsist V6.84 software, with the aim of establishing the most efficient option in terms of power generation. The simulation results show that photovoltaic panels can produce 151650 kWh (Option 1) and 150894 kWh (Option 2) per year, while the required amount of energy is 42726.77 kWh. The electricity produced exceeds the electricity requirements for the decorative lighting of the Cathedral Church, so it can be used for other purposes in the sacral complex.

In light of climate changes, technological development and the use of renewable energy sources are considered very important nowadays, both in newly-designed structures and reconstructed historic building, resulting in the reduction of the commercial energy consumption and CO₂ environmental emissions. This paper explores the possibilities of improving the energy efficiency of heritage sacred buildings by utilizing photovoltaic systems. As an exceptionally significant cultural good, the Cathedral of St. Michael the Archangel in Belgrade shall serve as a case study, with the aim of examining the methods of mounting photovoltaic (PV) panels, by taking into account the fact that the authenticity and the aesthetic value of this cultural monument must remain intact. A comparative analysis of the two options for installing PV panels on the southwestern roof of the church was performed using simulations in PVgis and PVsist V6.84 software, with the aim of establishing the most efficient option in terms of power generation. The simulation results show that photovoltaic panels can produce 151650 kWh (Option 1) and 150894 kWh (Option 2) per year, while the required amount of energy is 42726.77 kWh. The electricity produced exceeds the electricity requirements for the decorative lighting of the Cathedral Church, so it can be used for other purposes in the sacral complex.

Even though the current classic aerospace propulsion methods are greatly improved, some of the most modern methods have already been introduced, among which the propulsion with electric motors. Energy can be obtained from hydrogen burners, honeycomb burners to protect the burning of hydrogen that burns 10 times faster than conventional oil fuels or alcohols. Hydrogen storage is also done in honeycomb cell reservoirs. Getting solar photovoltaic power even during flight is not yet profitable or efficient, but it can be proposed in the future for lighter and/or spacecraft. A great desire is to dismantle water in hydrogen and oxygen directly on the aircraft, so the stored fuel is actually water and the one actually used is the hydrogen removed from the water. In this case, there is no need for hydrogen storage. And other modern methods of propulsion and energy acquisition are briefly presented in the paper.

We present a review of the current state of the field for a rapidly evolving group of technologies related to solar energy harvesting in built environments. In particular, we focus on recent achievements in enabling the widespread distributed generation of electric energy assisted by energy capture in semi-transparent or even optically clear glazing systems and building wall areas. Whilst concentrating on the cutting-edge recent results achieved in the integration of traditional photovoltaic device types into novel concentrator-type windows and glazings, we compare the main performance characteristics reported with these achievable using more conventional (opaque or semi-transparent) solar cell technologies. A critical overview of the current status and future application potential of multiple existing and emergent energy harvesting technologies for building integration is provided.

This study presents application of demand response strategy in a standalone wind-solar-battery hybrid energy system (HES). Inputs for the designed HES are wind speed, solar radiation, temperature and load demand which is variable with time. In this study, hourly values of meteorological data and hourly load demand are considered in one year. An improved gravitational search algorithm (IGSA) is used to optimize the configuration of the standalone wind-solar-battery hybrid power system. The optimal objectives of the system are cost of the system in life cycle, the loss of power supply probability（LPSP）and the energy excess percentage（EXC）.The effect of demand response on economic benefit and energy storage allocation of the standalone wind-solar-battery system is studied. The obtained optimal configuration of the proposed HES can provide minimal energy cost with excellent performance and reduced waste and unmet load.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of simulation and statistical results of EO with other optimization techniques showed that EO is more effective and superior.

Clarifying the distribution of temperature and pressure in the wellbore and cavern during hydrogen injection and extraction is crucial for quantitatively assessing cavern stability and wellbore integrity. This paper establishes an integrated flow and heat transfer model for the cavern and wellbore during hydrogen injection and production, analyzing the variations in temperature and pressure in both the wellbore and the cavern. The specific conclusions are as follows. (1) The temperature and pressure parameters of hydrogen and natural gas within the chamber and wellbore were compared. Under identical injection and production conditions, the temperature of hydrogen in the chamber was 10°C higher than that of natural gas, and 16°C higher in the wellbore. The pressure of hydrogen in the chamber was 2.9 MPa greater than that of natural gas, and 2.6 MPa higher in the wellbore. (2) A comparative analysis was conducted on the impact of surrounding rock’s horizontal and numerical distance on temperature during hydrogen and natural gas injection processes. As the distance from the cavity increases, from 5 to 15 meters, the temperature fluctuation in the surrounding rock diminishes progressively, with the temperature effect in the hydrogen storage chamber extending at least 10 meters. (3) The influence of rock thermal conductivity parameters on temperature during the processes of hydrogen injection and natural gas extraction is compared. The better the thermal conductivity, the deeper the thermal effects penetrate the rock layers, with the specific heat capacity having the most significant impact.