One of the relevant goals in forging technologies is simplifying the existing process and developing new processes that can retain the original or very close to the original dimensions and billet shape after the end of the deformation cycle. This study attempts to develop a forging equipment design that provides alternating cyclic loading; the alternate cyclic forging (ACF) method is proposed. To preliminary evaluate the ACF and study the plastic deformation behavior, numerical simulation via finite element modeling (FEM) was conducted using DEFORM-3D. The main attention was paid to the metal flow characteristics, effective strain and stress distribution, and the forging load. The ACF results in non-uniform metal flow with the formation of diagonal and vortex flows were demonstrated. Maximum effective strains and stresses zones are localized at two points of the billet contact with the surface of the tooling container and at two points of the interface between the punches. It was also assumed that reducing the contact area between the punch and the billet using separate semi-cylindrical punches can reduce the forging load. Preliminary finite element analysis (FEA) results of the proposed process after four successive steps of the deformation cycle confirmed the feasibility of its general implementation.

Lithium-metal batteries offer high energy density, but are challenged by dendrite growth, which can lead to short circuits and battery failure. Various models with varying degrees of accuracy and computational cost have been developed to understand and predict dendrite growth. In this study, a simple simulation model to predict macroscale dendrite growth on lithium metal electrodes is presented. The model uses a 3D single-particle diffusion-limited aggregation (DLA) algorithm, biased by the electric field, to simulate dendrite growth. The model was validated using 3D MRI of dendrite growth in a lithium symmetric cell. It was used to simulate deposition between consecutive measured dendrite structures. The model also introduces an important parameter, namely the biasing factor c, which determines the balance between diffusion and electric field effects. This parameter was calibrated using the overlap and displacement of deposition sites metrics, achieving optimal results at c = 0.7. The model predictions were in good agreement with experimental data confirmed by fractal dimension analysis. This model provides a useful tool for predicting and studying dendrite formation in lithium and other metal batteries.

Objective: This study aimed to assess the impact of artificial intelligence (AI)-driven noise reduction algorithms on metal artifacts and image quality parameters in cone-beam computed tomography (CBCT) images of the oral cavity. Materials and Methods: This retrospective study included 70 patients, 61 of whom were analyzed after excluding those with severe motion artifacts. CBCT scans, performed using a Hyperion X9 PRO 13 × 10 CBCT machine, included images with dental implants, amalgam fillings, orthodontic appliances, root canal fillings, and crowns. Images were processed with ClariCT. AI deep learning model (DLM) for noise reduction. Objective image quality was assessed using metrics such as the differentiation between voxel values (ΔVVs), the artifact index (AIx), and the contrast-to-noise ratio (CNR). Subjective assessments were performed by two experienced readers, who rated overall image quality and artifact intensity on predefined scales. Results: Compared with native images, DLM reconstructions significantly reduced the AIx and increased the CNR (p<0.001), indicating improved image clarity and artifact reduction. Subjective assessments also favored DLM images, with higher ratings for overall image quality and lower artifact intensity (p<0.001). However, the ΔVV values were similar between the native and DLM images, indicating that while the DLM reduced noise, it maintained the overall density distribution. Orthodontic appliances produced the most pronounced artifacts, while implants generated the least. Conclusion: AI-based noise reduction using ClariCT. AI significantly enhances CBCT image quality by reducing noise and metal artifacts, thereby improving diagnostic accuracy and treatment planning. Further research with larger, multicenter cohorts is recommended to validate these findings.

With the ever-growing emphasis on global decarbonization and rapid increases in the power density of electronics equipment in recent years, new methods and lightweight materials have been developed to manage heat load as well as interfacial stresses associated with Coefficient of Thermal Expansion (CTE) mismatch between components. The Al-Si system provides an attractive combination of CTE performance and high thermal conductivity whilst being a very lightweight option. Such materials are of interest to industries where thermal management is a key design criterion, such as aerospace, automotive, consumer electronics, defense, EV and space. This paper will describe the development and manufacture of a family of high-performance hypereutectic Al-Si alloys (AyontEX™) by a powder metallurgy method. These alloys are of particular interest for structural heat sink applications that require high reliability under thermal cycling (CTE of 17μm/(m·°C)) as well as reflective optics and instrument assemblies that require good thermal and mechanical stability (CTE of 13μm/(m·°C)). Critical performance relationships are presented, coupled with the microstructure, physical and mechanical properties of these Al-Si alloys.

Transition metal complexes have historically played a pivotal role in creating vibrant pigments utilized across artistic mediums such as ceramics, paintings, and glass mosaics. Despite their extensive historical use, our understanding of the mechanisms governing transition metal complex behavior has predominantly emerged in recent times, leaving numerous aspects of this process ripe for exploration. These complexes exhibit striking color variations under diverse conditions when employed in pigment formulations. This review utilizes a bottom-up scientific approach, spanning from microscopic to macroscopic scales, to unravel the molecular origins of the colors generated by transition metal complexes in pigments and ceramic glazes. Advanced spectroscopy techniques and computational chemistry play pivotal roles in this endeavor, highlighting the significance of understanding and utilizing analytical data effectively, with careful consideration of each technique's specific application. Furthermore, the review investigates the influence of processing conditions on color variations, providing valuable insights for artists and manufacturers aiming to enhance the precision and quality of their creations while mitigating environmental impact.

Dissimilar welds between ferritic and austenitic steels represent a good solution for exploiting the best performance of stainless steels at high and low temperatures and in aggressive environments, while minimizing costs. Therefore, they are widely used in nuclear and petrochemical plants, however, due to the different properties of the steels involved, the welding process can be challenging. Fusion welding can be specifically addressed to connect low-carbon, or low-alloy steels, with high-alloy steels, which have similar melting point. Welding of thick plates can be performed with electric arc in multiple passes or in a single pass by means of a laser beam equipment. Since microstructure and consequently mechanical properties of the weld are closely related to composition, the choice of the filler metal and processing parameters, which in turn affects the dilution rate, plays a fundamental role. Numerous technical solutions were proposed for welding dissimilar steels and much research was developed on the weldment metallurgy; therefore, this article is aimed at a review of the most recent scientific literature on the issues relating to the fusion welding of ferritic / austenitic steels. Two specific sections are dedicated respectively to electric arc and laser beam welding; finally, metallurgical issues, related to dilution and thermal field are debated in the discussion section.

Memristors are state-of-the-art, nano-sized, two-terminal, passive electronic elements with very good switching and memory characteristics. Owing to their very low power usage and a good compatibility to the existing CMOS ultra-high-density integrated circuits and chips, they are po-tentially applicable in artificial and spiking neural networks, memory arrays, and many other de-vices and circuits for artificial intelligence. In this paper, a complete electronic realization of ana-log circuit model of modified neural net with memristor-based synapses and transfer function with memristors and MOS transistors in LTSPICE is offered. Each synaptic weight is realized by only one memristor, providing enormously reduced circuit complexity. The summing and scaling implementation is founded on op-amps and memristors. The logarithmic-sigmoidal activation function is based on a simple scheme with MOS transistors and memristors. The functioning of the suggested memristor-based neural network for pulse input signals is evaluated both analytically in MATLAB-SIMULINK and in LTSPICE environment. The obtained results are compared one to another and are successfully verified. The realized memristor-based neural network is an im-portant step towards the forthcoming design of complex memristor-based neural networks for ar-tificial intelligence, for implementation in very high-density integrated circuits and chips.

Contrast agents developed for X-ray computed tomography (CT) offer extremely valuable tools and techniques in diagnostics via contrast enhancements. Heavy metal-based nanoparticles (NPs) can provide high contrast in CT images. These result from a high density of heavy metal atoms with high X-ray attenuation coefficients that exceed that of iodine (I), which is currently used in hydrophilic organic CT contrast agents. Nontoxicity and colloidal stability are vital characteristics in designing heavy metal-based NPs as CT contrast agents. In addition, the particle size must be small for in vivo renal excretion. In vitro phantom imaging studies can provide X-ray attenuation efficiency, which is a critical parameter for CT contrast agents, and the imaging performance of CT contrast agents can be demonstrated via in vivo experiments. This review focuses on in vitro and in vivo studies of various heavy metal-based NPs (metal: Au, Pt, Pd, Ag, Ce, Gd, Dy, Ho, Yb, Ta, W, and Bi) and provides an outlook on their use as high-performance CT contrast agents.

The response of plasmonic metal particles to an electromagnetic wave undergoes significant features at the nanoscale level. Different properties of the internal composition of a metal, such as its ionic background and the free electron gas, begin to manifest more prominently. As the dimensions of the nanostructures decrease, the classical local theory gradually becomes inadequate. Therefore, Maxwellʹs equations need to be supplemented with a relationship determining the dynamics of current density which is the essence of nonlocal plasmonic models. In this field of physics, the standard (linearized) hydrodynamic model (HDM) has been widely adopted with great success, serving as the basis for a variety of simulation methods. However, ongoing efforts are also being made to expand and refine it. Recently, the GNOR (general nonlocal optical response) modification of the HDM has been used, with the intention of incorporating the influence of electron gas diffusion. Clearly, from the classical description of fluid dynamics, a close relationship between viscosive damping and diffusion arises. This offers a relevant motivation for introducing the GNOR modification in an alternative manner. The standard HDM and its existing GNOR modification also do not include the influence of interband electron transitions in the conduction band and other phenomena that are part of many refining modifications of the Drude‐Lorentz and other models of metal permittivity. In this article, we present a modified version of GNOR‐HDM that incorporates the viscosive damping of the electron gas and a generalized Drude‐Lorentz term. In the selected simulations, we also introduce Landau damping which corrects the magnitude of the standard damping constant of the electron gas based on the size of the nanoparticle. We have chosen a spherical particle as a suitable object for testing and comparing HD models and their modifications because it allows finding precise analytical solutions for the interaction and, simultaneously, it is a relatively easily fabricable nanostructure in practice. Our contribution also includes our own analytical method for solving the HDM interaction of a plane wave with a spherical particle. This method forms the core of calculations of the characteristic quantities, such as the extinction cross‐sections and the corresponding components of electric fields and current densities.

This short review is aimed at giving an overview of catalytic carbonylative double cyclization reactions, which are processes in which suitable organic substrates and carbon monoxide are sequentially activated by a promoting catalyst to afford the formation of two new cycles with concomitant incorporation of carbon monoxide as a carbonyl function into the final product. Paradigmatic examples of this powerful synthetic methodology, which allows the one-step synthesis of complex molecular architectures from simple building blocks using the simplest and readily available C-1 unit (CO) are illustrated and discussed. The review is divided into five sections: 1) Introduction; 2) Functionalized Olefinic Substrates; 3) Functionalized Acetylenic Substrates; 4) Functionalized Halides; 5) Conclusions and Future Perspectives.

Plazomicin is a recently U.S. Food and Drug Administration (FDA)-approved semisynthetic aminoglycoside. Its structure consists of a sisomicin scaffold modified by adding a 2(S)-hydroxy aminobutyryl group at the N1 position and a hydroxyethyl substituent at the 6′ position. These substitutions produced a molecule refractory to most aminoglycoside-modifying enzymes. The main enzyme within this group that recognizes plazomicin as substrate is the aminoglycoside 2′-N-acetyltransferase type Ia [AAC(2′)-Ia], which reduces the antibiotic’s potency. Designing formulations that combine an antimicrobial with an inhibitor of resistance is a recognized strategy to extend the useful life of existing antibiotics. We have recently found that several metal ions inhibit acetylation of numerous aminoglycosides catalyzed by the aminoglycoside 6′-N-acetyltransferase type Ib [AAC(6′)-Ib]. In particular, Ag1+, which also enhances the effect of aminoglycosides by other mechanisms, is very effective in interfering with AAC(6′)-Ib-mediated resistance to amikacin. Here we report that silver acetate is a potent inhibitor of AAC(2′)-Ia-mediated acetylation of plazomicin in vitro, and it reduces resistance levels of Escherichia coli carrying aac(2′)-Ia. The resistance reversion assays produced equivalent results when the structural gene was expressed under the control of the natural or the blaTEM-1 promoters. The antibiotic effect of plazomicin in combination with silver was bactericidal, and the mix did not show significant toxicity to human embryonic kidney 293 (HEK293) cells.

Residual stresses in fiber metal laminates (FML) inevitably develop during the manufacturing process. The main contributor to these stresses is the difference in the coefficients of thermal expansion (CTE) between fibers and metal in combination with high process temperatures. To quantify these stresses, the use of specimens with an asymmetric layup is an easily adaptable method. The curvature that develops after the manufacturing of flat laminates with an asymmetrical layer stack is a measure of the level of residual stresses evolving during cure. However, the accuracy of the curvature evaluation is highly dependent on specimen design and other influencing parameters. In this work a large set of FML specimens is investigated to identify relevant influencing parameters and derive conclusions about specimen design and evaluation techniques. For certain layups and process parameters, there is a good correlation between the curvature and the stress-free temperature, which is further covered by analytical solutions for bimetals. This correlation is the basis to transfer curvature into a stress-free temperature that can consequently be used for the quantification of residual stress levels in more complex FMLs. The transfer is validated by in-situ strain measurements during cure using a strain gage technique. Based on the results, the application of asymmetric specimens for residual stress characterization in more complex laminates is presented in the form of a workflow.

Structural health monitoring of lightweight constructions made of composite materials can be performed using guided ultrasonic waves. If modern fiber metal laminates are used, this requires integrated sensors that can record the inner displacement oscillations caused by the propagating guided ultrasonic waves. Therefore, we have developed a robust MEMS vibrometer that can be integrated with structural and functional compliance. This vibrometer is directly sensitive to the high-frequency displacements from structure-borne ultrasound when excited between its first and second natural frequency. The vibrometer is mostly realized by processes earlier developed for a pressure sensor but with additional femtosecond laser ablation and wafer bonding. The piezoresistive transducer made from silicon is encapsulated between top and bottom glass lids. The natural frequencies are experimentally determined using an optical micro vibrometer setup. The vibrometer functionality and usability for structural health monitoring are demonstrated on a customized test rig by recording application-relevant guided ultrasonic wave packages with a central frequency of 100 kHz at a distance of 200 mm from the exciting ultrasound transducer.

Radially polymerized dendritic compounds are nowadays an established polymer category next to their linear, branched and cross-linked counterparts. Their uncommon tree-like architecture is characterized by adjustable internal cavities and external groups. They are therefore exceptional absorbents and this attainment of high concentrations into their interior renders them ideal reac-tion media. In this framework they are applied in many environmentally benign implementa-tions. One of the most important among them is water purification though pollutant decomposi-tion. Simple and composite catalysts and photo-catalysts containing dendritic polymers and ap-plied in water remediation will be discussed jointly with some unconventional solutions and fu-ture prospects.

For the better part of a century researchers across disciplines have sought to explain the crystallography of the elemental transition metals: hexagonal close packed, body centered cubic, and face centered cubic in a form similar to that used to rationalize the structure of organic molecules and inorganic complexes. Pauling himself tried with limited success to address the origins of transition metal stability. These early investigators were handicapped, however, by incomplete knowledge regarding the structure of metallic charge density. Here we exploit modern approaches to charge analysis to first comprehensively describe transition metal charge density. Then, we use topological partitioning and quantum mechanically rigorous treatments of kinetic energy to account for the structure of the density as arising from the interactions between metallic tetrahedra. We argue that the crystallography of the early transition metals results from charge transfer from the so called “octahedral” to “tetrahedral holes” while the face centered cubic structure of the late transition metals is a consequence of antibonding interactions that increase octahedral hole kinetic energy.

Non steady applied magnetic field impact on a liquid metals has good prospects for industry. For a better understanding of heat and mass transfer processes under these circumstances, numerical simulations are needed. A combination of finite elements and volumes methods was used to calculate the flow and solidification of liquid metal under electromagnetic influence. Validation of numerical results was carried out by means of measuring with ultrasound Doppler velocimetry technique, as well as with neutron radiography snapshots of the position and shape of the solid/liquid interface. As a result of the first part of the work, a numerical model of electromagnetic stirring and solidification was developed and validated. This model could be an effective tool for analyzing the electromagnetic stirring during the solidification process. In the second part, the dependences of the velocity pulsation amplitude and the melt velocity maximum value on the magnetic field pulsation frequency are obtained. It was found numerically the ability of the pulsating force action to develop higher values of the liquid metal velocity at a frequency close to the MHD resonance. Obtained characteristics give a more detailed description of the electrically conductive liquid behaviour under action of pulsating traveling magnetic field.

The recovery of precious metals is a project with both economic and environmental significance. In this paper, it presents how to use bacterial mineralization to selectively recover gold from multi-ionic aqueous systems. The Bacillus licheniformis FZUL-63, separated from a landscape lake in FuZhou University, was shown to selectively mineralize and precipitate gold from coexisting ions in aqueous solution. The removal of Au(III) was almost happened in first hour, and FTIR data show that the amino, carboxyl and phosphate groups on the surface of the bacteria are related to the adsorption of gold ions. XPS results implied that Au(III) ions are reduced to monovalent, and then the Au(I) was adsorbed on the bacterial surface at the beginning stage(first hour). XRD results showed the gold biomineralization began about 10 hours after the interaction between Au(III) ions and bacteria. The Au(III) mineralization has been rarely influenced by other co-existing metal ions. TEM analysis shows the gold nanoparticles are polyhedral structure with a particle size of ~20 nm. The Bacillus licheniformis FZUL-63 could selectively mineralize and recover 478 mg/g(dry biomass) gold from aqua regia-based metal wastewater through four cycles. It could be of great potential in the practical application.

Attaining sustained soil fertility is essential for guaranteeing global food security and environmental well-being. Traditional farming methods that depend extensively on synthetic fertilizers have resulted in soil deterioration and environmental contamination. Biological fertilizers fortified with micronutrients have emerged as viable alternatives. This analysis examines many types of biological fertilizers and their contribution to improving soil fertility via micronutrient enhancement. Multiple sources of micronutrient-enriched biological fertilizers, such as microbial inoculants, compost, and organic amendments, are evaluated for their effectiveness in enhancing plant growth, increasing nutrient availability, and boosting soil health. Moreover, the effects of these fertilizers on agricultural productivity, soil microbial populations, and ecological sustainability are examined. Green manuring is a reasonable and ecofriendly scientific approach to enhancing robust and sustainable food production in agricultural systems. The integration of green manure improves soil quality by augmenting its chemical, physical, and biological properties, including the availability of organic matter, potassium, nitrogen, and phosphorus, while also enhancing soil structure by reducing erosion and improving water retention capacity. Green manure serves as a natural fertilizer, releasing nutrients into the soil during decomposition, so enhancing nutrient content and fostering plant growth and development. The results highlight the potential of biological fertilizers as sustainable solutions for improving soil fertility and decreasing reliance on synthetic inputs, hence promoting long-term agricultural output and ecosystem resilience.

This research aims to develop top-emission OLEDs (Organic Light light-emitting diodes) that exhibit enhanced electro-optical properties regarding color purity, luminance, efficiency, stability, and longer lifetime. To achieve this aim, we have used silicon wafer substrates with a thickness of 675 m. Top-emission OLED fabrication on silicon wafer substrates requires careful material selection and layer configuration. This device structure is described as follows: Silicon/Al (100 nm)/ HATCN (10 nm)/ Dic-TRZ: Ir(mppy)3 (40 nm)/ TPBi (30 nm)/ LiF 1.2 nm / Al 19.9 nm. LiF/Al combination is used as the semi-transparent cathode. Research on top-emission OLEDs has demonstrated the importance of silicon wafer substrates in enhancing electro-optical properties. The optical properties of top-emission OLEDs are significantly influenced by factors such as the semitransparent cathode layer's thickness and the anode layer's surface roughness. Study findings encompass the impact of microcavity on TEOLEDs, dopant concentration on device performance, and device thermal conductivity and lifetime. To create a highly efficient top-emission OLED on a silicon substrate, we meticulously fine-tuned parameters such as the thickness of the cathode Al layer (19.9 nm), the organic layer thickness (HIL - HATCN 10 nm, HTL - NPB 30 nm, ETL - TPBi 30 nm, EML - DIC–TRZ: Ir(mppy)3 40 nm), and the dopant concentration. Electro-optical performance has been significantly improved through optimization, especially in devices with high dopant concentrations. The 38% dopant concentration experiments resulted in a peak current density of 201.97 mA/cm2, a luminance of 4776 cd/m2, and an efficiency of 2.36 cd/A at 9 V. In addition, the high dopant concentration has resulted in a narrow spectral range, indicating a strong microcavity effect. Additionally, Si-TEOLEDs were tested for lifetime under these specific conditions, exhibiting a half-life of 420 hours.

The bimetallic (Ta/(Ti, V, Co, Nb) mesoporous MCM-41 nanoparticles were obtained by direct synthesis and hydrothermal treatment. The obtained mesoporous materials were characterized by XRD, XRF, N2 adsorption/desorption, SEM, TEM, XPS, Raman, UV-Vis, PL spectroscopy. A more significant effect was observed on mesoporous structure, typi-cally for MCM-41, and optic properties if the second metal (Ti, Co) does not belong to the same Vb group with Ta as V, Nb. The obtained new nanoparticles were used as catalysts for oxidation with H2O2 of olefinic compounds (1,4 cyclohexadiene, cyclohexene, styrene) and photodegradation of organic pollutants (phenol, methyl orange) from water. The re-sults showed improving of activity and selectivity in oxidation reactions by addition of the second metal to Ta-MCM-41 catalyst. The slow addition of H2O2 was also be benefit for the selectivity in epoxide products and stability of the catalysts. The band gap energy values decrease in the presence of the second metal and the band edge diagram evidenced posi-tive potential for all the conduction band of the bimetallic samples except TaTi-MCM-41. The higher photocatalytic degradation was obtained for samples with TaTi and TaV.

Cured-in-place pipe (CIPP) lining is a widely adopted method for pipeline renewal, offering advantages such as rapid installation and cost-effectiveness. However, concerns regarding the environmental impacts of volatile organic compound (VOC) emissions during the installation process have raised issues regarding the CIPP method. The literature review conducted in this paper indicated the need for stringent monitoring and management practices to mitigate adverse effects, emphasizing the importance of safe installation protocols. This paper presents the initial results of a case study focusing on VOC emissions, specifically investigating non-styrene polyester resins and water curing. To capture emissions from CIPP activities, the methodology involved air sampling using various equipment, including photoionization detectors (PID), summa canisters, passive worker sampler sorbent tubes, and method 13 cartridges. The preliminary findings indicate that non-styrene polyester resins do not exceed the exposure limits set out by the OSHA and USEPA. The future phases of this project will explore different resins and curing methods.

Conjugated polymers (CPs) offer potentials for sustainable semiconductor devices due to their low cost, and inherent molecular self-assembly. Enhanced crystallinity and molecular orientation in thin films of solution-processable CPs have significantly improved organic electronic device per-formance. In this work, three methods namely spin-coating, dip-coating, and unidirectional float-ing-film transfer method (UFTM) were utilized with their parametric optimization for fabricating RR-P3HT films. These films were then utilized for their characterization via optical and micro-structural analysis to elucidate dominant roles of molecular orientation, and crystallinity in con-trolling charge transport in organic field-effect transistors (OFETs). OFETs fabricated by RR-P3HT thin films using spin-coating and dip-coating displayed field-effect mobility (μ) of 8.0 × 10-4 cm2V-1s-1 and 1.3 × 10-3 cm2V-1s-1, respectively. This two-time enhancement in (µ for dip-coated films was attributed to its enhanced crystallinity. Interestingly, UFTM films based OFETs demon-strated μ of 7.0 × 10-2 cm2V-1s-1, >100 times increment as compared to its spin-coated counterpart This superior device performance is attributed to synergistic influence of higher crystallinity and molecular orientation. Since the crystallinity of dip-coated and UFTM-thin films are similar ~50 times improved µ of UFTM thin films suggest a dominant role of molecular orientation as com-pared to crystallinity in controlling the charge transport.

Soil secondary salinization has seriously affected the greenhouse vegetable production in China. To improve the secondary salinization greenhouse soil and enhance the soil physical-chemical properties in an eco-environmental way, different organic amendments (straw, straw biochar, Trichoderma bio-organic manure, commercial organic manure) were applied using pot experiment for 60 day to comprehensively screen the optimal remediation method. In this study, soil nutrient condition and salt movement were assessed, and predictive models using multi-linear regression (MLR) and Random Forest (RF) were developed to estimate soil salinization parameters. The findings indicated a significant decrease in soil salt content following the application of organic materials compared to the control treatment. Specifically, the addition of straw at a rate of 250g/kg resulted in a 59.38% reduction in soil salt levels after 60 days (P < 0.05). Furthermore, the main salt ions exhibited dynamic changes over the course of the experiment, with reductions observed in Na+, Ca2+, Cl-, and NO3- content under the 250 g/kg straw treatment by 83.63%, 74.67%, 63.26%, 59.07%, respectively, compared to CK (P < 0.05). In addition, the SO42- content under 125 g/kg commercial organic manure amendment reduced by 48.94%, respectively (P < 0.05). Contrary to expectations, the addition of organic materials significantly increased the levels of total nutrients (N/P/K) and available potassium (AK) and phosphorus (AP) in the soil. Specifically, the addition of straw at a rate of 250 g/kg resulted in increases of 18.02%-87.38% in total potassium (TK), 66.67%-200% in total phosphorus (TP), and 142.87%-367.8% in AK after a period of sixty days (P < 0.05). Ultimately, the treatment involving the addition of 250 g/kg of straw demonstrated the most pronounced impact on the physical and chemical properties of the soil. The random forest method shows promise in accurately predicting soil salt and soil sodium adsorption ratio (SAR)indicators, thereby providing a valuable tool for estimating soil properties.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

In recent years, online review system attracts attention to assess seller-customer relations in the world of e-commerce. To address the quality concern of online review, especially incentivized ones, this study evaluates credibility and consistency based on reviews’ volume, length, and content to distinguish the impact of incentives on customer review behavior, improving review quality, and purchase decision-making. Software product reviews collected from software review websites, including Capterra, Software Advice, and GetApp undergo Exploratory Data Analysis (EDA) to reveal critical features such as cost, support, usability, and product features. The indirect impact of companies’ size, direct impact of users’ experience, and different impacts of changing situations during years on the incentive reviews’ volume are major findings of sentiment analysis. A/B testing results show a minimal to no impact of such reviews on purchasing decisions, highlighting discrepancies in credibility and consistency in volume, length, and content. Employing advanced techniques like Sentence-BERT (SBERT) and TF-IDF, the study explores semantic differences in reviews to improve recommendation systems for a more customized shopping experience. This approach seeks to establish a framework that discerns between review types and their effect on customer behavior. The findings contribute to developing more sophisticated and consistent e-commerce solutions, emphasizing the importance of authentic and reliable online reviews in influencing consumer choices.

The impact of long-term soil and crop management practices on soil biological and chemical properties in oilseed brassica-based production systems were deliberated for holistic soil health improvement in the present study. Different tillage, crop residue re-cycling and cropping systems were studied for 5-years in 0-15 and 15-30 cm soil profiles. No-till permanent beds with crop residue (PB+R) noticeably improved soil organic carbon (SOC), microbial biomass carbon (MBC), enzymes [dehydrogenase (DHA) and alkaline phosphatase (AlP)], nitrogen fractions (available, nitrate and total), and available phosphorus and potassium content in both the soil layers compared to conventional tillage without crop residues. Though, the plow soil layer (0-15 cm) showed higher concentration of soil carbon, enzymes, N fractions and available P than in the sub soil (15-30 cm). The dynamic soil biological and chemical properties were also varied with the crop stage, and recorded higher MBC at 30 days, SOC and enzymatic activities at 60 days, and N fractions and available P and K at harvest of mustard crop. Green gram-mustard rotation showed higher values of biological and chemical parameters. Thus, the legume-based mustard crop rotation following no-till permanent beds and residue re-cycling found holistic in improving soil health, and nutrient cycling.

This study deals with the computational analysis of the kinetic processes of a microbial electrolysis cell assisted-anaerobic digestion (MEC-AD) treating raw-waste activated sludge (WAS), comparatively with a conventional AD, as well as the effect of the Organic Loading Rate (OLR) on the system’s performance. The aim was to derive a single kinetic and mathematical model for the study of the MEC-AD, using the ADM1 framework, which can be utilized to extract the effect of an applied potential on the kinetics of AD. The experimental data were obtained from the long-term, continuous operation of two identical reactors (an AD and a MEC-AD), which were operated at different OLRs (1.1, 1.7 and 2.9 gCOD/(L*d)). The results showed that the MEC-AD yielded improved biomass yields, substrate consumption kinetics and 1st order disintegration kinetics, with a predominant contribution to disintegration of complex particulates, comparatively with the AD. Moreover, it enabled operation at higher OLRs (achieving the highest divergence from the AD at the OLR of 4.14 gCOD/(L*d)), therefore accelerating sludge treatment, as well as an improved performance at an increased solids retention time (SRT). These findings can serve as a quantitative guide for the effects of the operating parameters on the raw-WAS-fed MEC-AD performance.

The performance of two bio inoculants either in single or in combined applications with organic fertilizer was tested to determine their effect on plant growth and yield under normal and unfavorable field conditions such as low pH value and low content of P. Arbuscular Mycorrhiza Fungi ((AMF; three species of Glomus) and the plant growth-promoting bacterial strain Kosakonia radicincitans DSM16656 were applied to barley in two years field experiment with different soil pH levels and available nutrients. Grain yield, content of P, N, K, Mg, and soil microbial parameters were measured. Grain yield and content of nutrients were significantly increased by the applications of mineral fertilizer, organic fertilizer, AMF, K. radicincitans, and combined application of organic fertilizer with AMF and with K. radicincitans over the control under normal growth conditions. Under low pH and low P conditions, only the combined application of the organic fertilizer with K. radicincitans and organic fertilizer with AMF could increase grain yield and content of nutrients of barley over the control.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

One of the biggest problems that the Dominican Republic has had in recent decades is the efficient management of solid waste produced by the population. This problem has worsened in recent years due to the decrease in available areas for the construction of sanitary landfills, the lack of recycling culture in the population, the deficiency in waste collection, and the scarce legal controls aimed at preserving water and air and soil, among other factors. The objective of this study was to explore the management of solid waste by the population and the municipality of Puñal, province of Santiago, to evaluate and analyze the situation and generation of solid waste, municipal solid waste management services, and the attitudes of the population regarding recycling projects and waste management, to evaluate the viability and sustainability of the use organic waste for energy generation. A total of 275 households from 29 localities in the municipality of Puñal were surveyed, which allowed for a significant population sample. According to the results obtained, the most significant type of waste produced by families is organic waste, followed by plastic waste and paper. Of the total organic waste produced in the municipality, 53% of solid waste is disregarded through the municipal waste collection system, while 47% is used as plant fertilizers or animal feed. On the other hand, most households receive the municipal waste collection service and pay for this service. The results of our research show that the implementation of an energy production system based on organic waste would be viable in the municipality of Puñal. However, a more efficient waste collection system would be necessary and the development of programs and projects that allow all households to participate in the system.

(1) Predictive assessment of the performance characteristics of metal-polymer (MP) plain bearings at the design stage is necessary and important for engineering practice. They include bearing capacity, linear wear of the bushing, and bearing life. However, no method for their calculation has been developed. (2) The authors have created a generalized analytical method for the mathematical modeling of MP sliding bearings as a classical science-based method of contact mechanics of conformal cylindrical bodies with consideration of polymer bushing wear. (3) Contact problem of the theory of elasticity takes into account the significant difference in the elasticity characteristics of polymeric materials from those of steel: Young's modulus is 60...250 times smaller, Poisson's ratio is 1.27...1.37 times larger. The method has been used to study MP bearings with several common groups of tribopolymers used for bushings: PA, PTFE, PET, and PEEK. The maximum contact pressures and durability of dry friction bearings have been calculated taking into account the load, radial clearance, bushing thickness, elasticity characteristics of tribopolymers, their wear resistance, sliding friction coefficient, and type of tribopolymer materials. (4) The paper establishes quantitative and qualitative regularities of the influence of these factors on the maximum contact pressures and bearing durability.

This article reports the preparation of a novel functionalized magnetic nanoadsorbent through an addition reaction between Fe3O4 nanoparticles coated with allyl silica gel and 4-pyridinyl ethylene, detailed characterization of Fe3O4@SiO2-yl-VP was conducted. Among them, in the infrared spectrum, we can easily see that the absorption peak of C=C stretching vibration at 1660 cm-1 in the raw material disappears after the addition reaction, indicating the successful grafting of polymer on the surface of silica gel. The appearance of N element in the EDS spectrum also proves the successful completion of the addition reaction and the successful synthesis of Fe3O4@SiO2-yl-VP. At pH=5 and pH=7, it only takes half an hour for Fe3O4@SiO2-yl-VP to achieve maximum adsorption capacities of 85.06 and 73.78 mg/g for Hg (II) and Pb (II), respectively. The adsorption process conforms to the Langmuir model and pesudo first and pesudo second order kinetic models, and can be reused 11 times, demonstrating excellent reusability.

Efforts to achieve carbon neutrality, which aims to reduce the net carbon emissions to zero by decreasing carbon emissions from human activities and increasing carbon absorption, are actively underway. Additionally, the search for clean energy alternatives to fossil fuels has become a global research trend. This paper presents research on metal-air batteries, focusing on the development of energy supply technologies that do not generate carbon emissions during power generation and require less space for power generation compared to existing renewable energy sources. The proposed Mg-Air Battery (MAB) in this study uses magnesium as the metal anode and theoretically offers a maximum open-circuit voltage of 3.1V and a high energy density of 6.8kWh/kg. While previous research has primarily focused on designing small-capacity cells and maximizing the performance of metal anodes, this study differentiates itself by designing a large-capacity MAB cell and optimizing its electrical performance. For the large-capacity cell design, the weight, shape, and size of the anode were designed based on MAB performance factors, and research was conducted on manufacturing methods to optimize the performance of the air cathode. Furthermore, to enhance usability and extend the lifespan of the MAB cell, it was designed to allow electrolyte circulation, and the electrolyte circulation performance was verified through simulations of fluid flow within the cell. Based on the study of the power performance of the newly designed large-capacity MAB cell, the feasibility of con-structing a kW-class system using multiple Mg-Air battery cell stacks was confirmed.

Landmines, with more than 600 varieties and an estimated 110 million scattered across various regions worldwide, pose a significant threat globally. Heavily found landmines like TM-62M, MON-100, PDM-1, etc., in the recent Russia-Ukraine war, confirm the continued incorporation of metals in munitions. Traditional handheld metal detectors are still state-of-the-art for technical sub-surface demining procedures but are slow, unsafe, and expensive. Drone-based metal detection techniques can provide promising solutions for the rapid and effective detection of landmines; however, their reliability and accuracy remain a concern, as a single miss can cost a life. In our research, we present the results of a comprehensive comparative analysis of three distinct metal detectors: the EM61 Lite, a highly sensitive air-borne metal detector specially designed for UXO detection; the CTX 3030, a traditional handheld all-metal detector; and the ML 3S, a traditional handheld ferrous-only detector. We tested these detectors in a test field containing various inert landmines similar to those currently found in landmine-affected countries, including Ukraine, the US, Russia, and Afghanistan. Our findings highlight the possible challenges and limitations of employing current airborne systems in practical scenarios. Our results also showcase the need for advanced image processing techniques for analyzing airborne metal detector data.

The binary metal oxide mesoporous interfacial layers (bi-MO meso IF layer) templated by a graft copolymer is synthesized between a fluorine-doped tin oxide (FTO) substrate and nanocrystalline TiO2 (nc-TiO2). Amphiphilic graft copolymers, Poly(epichlorohydrin)-graft-poly(styrene), PECH-g-PS, was used as a structure-directing agent, and the fabricated bi-MO meso IF layer exhibits good interconnectivity and high porosity. Even if the amount of ZnO in bi-MO meso IF layer increased, it was confirmed that the morphology and porosity of bi-MO meso IF layer was well maintained. In addtion, bi-MO meso IF layer coated onto FTO substrates show higher transmittance compared with a pristine FTO substrate and dense-TiO2/FTO, due to the reduced surface roughness of FTO. The overall conversion efficiency (η) of a solid state photovoltaic cells, dye-sensitized solar cell (DSSC) fabricated with nc-TiO2 layer/bi-MO meso IF layer TZ1 used as a photoanode reaches 5.0% at 100 mW cm-2, which is higher than that of DSSC with a nc-TiO2 layer/dense-TiO2 layer (4.2%), resulting from enhanced light harvesting, good interconnectivity, and reduced interfacial resistance. The cell efficiency of the device did not change after 15 days, indicating that the bi-MO meso IF layer with solid-state electrolyte has improved electrode/electrolyte interface and electrochemical stability. Additionally, commercial scattering layer/nc-TiO2 layer/bi-MO meso IF layer TZ1 photoanode fabricated solid state photovoltaic cells (DSSC) achieved an overall conversion efficiency (η) of 6.4% at 100 mW cm-2.

The paper presents the development of cheap and selective Paper-based Analytical Devices (PADs) for Pd(II) determination. The PADs were obtained with an azoic ligand, (2-(tetrazolylazo)-1,8 dihydroxy naphthalene-3,6,-disulphonic acid), termed TazoC, and filter paper as the substrate. The orange TazoC-PADs interact quickly with Pd(II) solutions by forming a complex purple-blue-colored already at a very acidic pH (lower than 2). The dye complexes no other metal ions at such an acidic media, making TazoC-PADs highly selective to Pd(II) detection. Besides, at higher pH values, other cations, for example, Cu(II) and Ni(II), can interact with TazoC through the formation of stable and pink-magenta-colored complexes; however, it is possible to quantify Pd(II) also in the presence of other cations using a multivariate approach. Indeed, by applying Partial Least Square regression (PLS), the spectra of the TazoC-PADs were related to the Pd(II) concentrations both when present alone in solution and also in the presence of Cu(II) and Ni(II). The PLS models correctly predicted Pd(II) concentrations in unknown samples and tap water spiked with the metal cation.

This paper focuses on parametric model order reduction (PMOR) of guided ultrasonic wave propagation and its interaction with damage in a fiber metal laminate (FML). Structural health monitoring in FML seeks to detect, localize and characterize the damage with high accuracy and minimal use of sensors. This can be achieved by the inverse problem analysis approach which employs the signal measurement data recorded by the embedded sensors in the structure. The inverse analysis requires to solve the forward simulation of the underlying system several thousand times. These simulations are often exorbitantly expensive and triggered the need for improving their computational efficiency. A PMOR approach hinged on the proper orthogonal decomposition method is presented in this paper. An adaptive parameter sampling technique is established with the aid of a surrogate model to efficiently update the reduced-order basis in a greedy fashion. A numerical experiment is conducted to illustrate the parametric training of the reduced-order model. The results show that the reduced-order solution based on the PMOR approach is accurately complying with that of the high fidelity solution.

As a candidate for bifunctional asymmetric catalysts containing a half-sandwich C–N chelating Ir(III) framework (azairidacycle), a dinuclear Ir complex with an axially chiral linkage is newly designed. An expedient synthesis of chiral 2,2’-bis(aminomethyl)-1,1’-binaphthyl (1) from 1,1-bi-2-naphthol (BINOL) was accomplished by a three-step process involving nickel-catalyzed cyanation and subsequent reduction with Raney-Ni and KBH4. The reaction of (S)-1 with an equimolar amount of [IrCl2Cp*]2 (Cp* = 5-C5(CH3)5) in the presence of sodium acetate in acetonitrile at 80 °C gave a diastereomeric mixture of new dinuclear dichloridodiiridium (5) through the double C–H bond cleavage, as confirmed by 1H NMR spectroscopy. A loss of the central chirality on the Ir centers of 5 was demonstrated by treatment with KOC(CH3)3 to generate the corresponding 16e amidoiridium complex 6. The following hydrogen transfer from 2-propanol to 6 provided diastereomers of hydrido(amine)iridium with retaining the bis(azairidacycle) architecture. The dinuclear chlorido(amine)iridium 5 can serve as a catalyst precursor for the asymmetric transfer hydrogenation of acetophenone with a substrate to catalyst ratio of 200 in the presence of KOC(CH3)3 in 2-propanol, leading to (S)-1-phenylethanol with up to 67% ee.

Penicillium digitatum is the major postharvest pathogen of citrus fruit under Mediterranean climate conditions. In the present work, we have addressed the study of the role of P. digitatum’s proteases in virulence following two complementary approaches. In a first approach, we have undertaken the functional characterization of the P. digitatum prtT gene, which codes for a transcription factor previously shown to regulate extracellular proteases in other filamentous fungi. Deletion of prtT caused a significant loss in secreted protease activity during in vitro growth assays. However, there was no effect on virulence. Gene expression of the two major secreted acid proteases was barely affected in the ΔprtT deletant during infection of citrus fruit. Hence, no conclusion could be drawn on the role of these secreted acidic proteases on the virulence of P. digitatum. In a second approach, we have studied the effect of different protease inhibitors and chelators in virulence. Co-inoculation of citrus fruit with P. digitatum conidia and a cocktail of protease inhibitors resulted in almost a complete absence of disease development. Analysis of individual inhibitors revealed that the metalloprotease inhibitor 1,10-phenanthroline was responsible for the observed effect. The application of metal ions reverted the protective effect caused by the metallopeptidase inhibitor. These results may set the basis for the development of new alternative treatments to combat this important postharvest pathogen.

There is much interest in effective copper chelators to correct copper dyshomeostasis in neurodegenerative and oncological diseases. In this study, a recombinant fusion protein for expression in E. coli cells was constructed from glutathione-S-transferase (GST) and the N-terminal domain (ectodomain) of human high affinity copper transporter CTR1 (hNdCTR1), which has three metal-bound motifs. Several biological properties of the GST-hNdCTR1 fusion protein were assessed. It was demonstrated that in cells, the protein was prone to oligomerization, formed inclusion bodies and displayed no toxicity. Treatment of E. coli cells with copper and silver ions reduced cell viability in a dose- and time-dependent manner. Cells expressing GST-hNdCTR1 protein demonstrated resistance to the metal treatments. These cells accumulated silver ions and formed nanoparticles that contained AgCl and Ag0. In this bacterial population, filamentous bacteria with length about 10 μm were often observed. The possibility for the fusion protein carrying extracellular metal binding motifs to integrate into the cell’s copper metabolism and its chelating properties are discussed.

In the field of quality analysis of food and flavoring products, gas chromatography – quadrupole mass spectrometry – ion mobility spectrometry (GC-QMS-IMS) is a powerful technique for the simultaneous detection of volatile organic compounds (VOC) by both QMS and IMS. GC is an established technique for the separation of complex VOC-rich foods such as beverages, dairy and fruit products as well as flavorings in general. While the subsequent detection by IMS features soft ionization of fragile compounds (e.g., terpenes) with characteristic drift times, MS provides the analytes’ m/z-values for database substance identification. A limitation of the prominently used static headspace-based GC-QMS-IMS systems is the substantially higher sensitivity of IMS in comparison to full scan QMS, which results in the detection of relevant VOC only in IMS, but not in the QMS analyzer. The present study describes a new prototypic trapped-headspace (THS)-GC-QMS-IMS setup, with optimized active flow regulation, able to gain valuable data of both detectors. This ultimately allows the combination of a soft ionization with m/z values obtained from database-searchable electron ionization (EI) spectra and as such, offers a substantial advantage in fields of quality control. The new setup features aligned retention times for IMS and MS and sufficient signal intensities for QMS and IMS. The analytical setup was evaluated with a set of mango puree samples from various provenances and the data was evaluated by suitable machine learning approaches. The results demonstrate that THS-GC-QMS-IMS allows for the classification of mango purees from different cultivars and can be a promising alternative method for authenticity control of food, flavors, and beverages.

Renal uric acid (UA) reabsorption is mainly mediated by urate transporter 1 (URAT1) and glucose transporter 9 (GLUT9). Dotinurad selectively inhibits URAT1 and do not inhibit other UA transporters such as GLUT9, ATP-binding cassette transporter G2 (ABCG2) and organic anion transporter1/3 (OAT1/3). We discovered that dotinurad improved metabolic parameters and renal function in hyperuricemic patients. We consider a significance of high selectivity in inhibiting URAT1 by dotinurad for metabolic syndrome, chronic kidney disease (CKD), and cardiovascular disease (CVD). Dotinurad inhibits selectively URAT1 and increases UA in the proximal tubules, and UA may compete with glucose for GLUT9, reducing glucose reabsorption. The inhibition of UA entry via URAT1 to liver and adipose tissues by dotinurad increased energy expenditure and decrease lipid synthesis and inflammation in rats. The inhibition of URAT1 in kidney, liver and adipose tissues improve metabolic parameters. CKD patients accumulate uremic toxins such as indoxyl sulfate (IS) in the body. ABCG2 regulates renal and intestinal excretion of IS which strongly affects CKD. OAT1/3 inhibitors suppress IS uptake into kidney, increasing plasma IS, which produces oxidative stress, inducing vascular endothelial dysfunction in CKD patients. The high-selective inhibition of URAT1 by dotinurad may be beneficial for metabolic syndrome, CKD and CVD.

This study reports the synthesis and characterization of novel per-fluorinated organic polymers with azo- and azomethine-based linkers using nucleophilic aromatic substitution. The polymers reveal variations in the fluorine content via the incorporation of decafluorobiphenyl and hexafluorobenzene linkers, which enhanced their hydrophobic nature. The rich fluorine polymers were slightly soluble in THF and have shown molecular weights between 4886 to 11948 g/mol. All polymers exhibit thermal stability in the range of 350-500°C, with varying thermal stability depending on the fluorine and nitrogen content. Conjugation of the polymers was confirmed through changes in the UV-Vis spectra, with a hypsochromic shift observed in all cases, more pronounced in azo-based fluorinated chains due to H-bonding on the nitrogen sites, chain conformations, and planarity. The optical band gap (Eg) of the polymers was determined from the UV-Vis data, with the Eg values of the azo-based fluorinated polymers being 1 eV higher than those of their corresponding linkers. The cross-linking formation was characterized by porosity measurements, with the azo-based polymer exhibiting the highest surface area of 770 m²/g with a pore volume of 0.35 cm³/g, while the open-chain azomethine-based polymer exhibited the lowest surface area of 285 m²/g with a pore volume of 0.0872 cm³/g. Porous structures with varied hydrophobicities were investigated as adsorbents for separating water-benzene and water-phenol mixtures and selectively binding methane/carbon dioxide gases from the air. The most hydrophobic polymers containing the decafluorbiphenyl linker were suitable for benzene separation, while the best methane uptake values were 6.14 and 3.46 mg/g for DAB-Z-1O and DAB-A-1O, respectively. DAB-Z-1h, with the highest surface area and rich in nitrogen sites, exhibited the highest CO₂ uptake at 298 K (17.25).

To provide the population with food, it is very important to re-cultivate "abandoned lands" that have been retired from agricultural use. Conversion of arable land into agricultural abandoned lands in the south of Kazakhstan is, first of all, was primarily associated with salinity. For the purposes of sustainable development, there is a need to develop proposals for re-mastering by studying their current state, reviewing world studies on the reclamation of salt-affected soils. Therefore, this study was devoted to the study of the current environmental and reclamation conditions of the abandoned lands of Otyrar district in the south Kazakhstan, as well as discussion and recommendations on their development. In the course of the research, the historical method is used in the study of the emergence and formation of abandoned lands, the method of geographical analysis during the territorial analysis of the research object, the statistical and comparison methods in showing the complexity and intensity of the problems, the cartographic, geo-informational and field research (reconnaissance) methods in the study of the condition of the abandoned lands in the research object and methods of grouping and analysis were used in the work with scientific data on the topic of research. By deciphering space images with the help of geoinformation technologies, it was revealed that the area of abandoned lands in the research object is 13688.9 ha, including the area of non-saline soils – 83.9 ha, weakly saline soils – 984.4 ha, medium saline soils – 2398.3 ha, highly saline soils – 10222,1 ha. A review of the methods and technologies proposed by scientists for the development and melioration of salt-affected lands was made. Taking into account the ecological and reclamation state of the object of research along with the material and technical capabilities of farms, 2 methods of developing abandoned lands (organic and agro-innovative) in the research object are proposed and the need for their use in case of soil salinization has been scientifically justified.

The use of the commercial simulator Aspen Plus® could bring an amelioration in the accuracy of the predictions of the chemical species composition in the output streams of the anaerobic digestion process, due to availability of a broad library of thermodynamic and phenomena transport properties in this commercial package. In the present investigation, the process simulation model for anaerobic digestion, which was originally developed by Rajendran et al. [1], has been modified by including a stoichiometric-equilibria reactor to calculate the extent of the ionization of the molecules present in the anaerobic digestate. The refined model offers a more accurate prediction of the composition of the biogas because it delves on the chemical equilibrium of the gaseous stream and the anaerobic digestate. Additionally, the refined model allows to assess the possibility of upgrading the gaseous stream to biomethane degree via manufacturing of ammonium bicarbonate. This processing pathway relies on the stabilization of the anaerobic digestate by means of biomass ash-based treatment. First of all, the titration of the manure digestate with the hydrochloric acid showed that a dose of 3.18 mEq/g would be required to attain the targeted pH of zero-point charge, upon addition of the sewage sludge ash in a ratio to the manure digestate of 0.6 ± 0.2 %. Secondly, the profiles of ammonia, carbon dioxide, and methane found in the biogas agree with both the pH of the treated digestate and the processes described in for the simultaneously upgrading the biogas and the production of ammonium bicarbonate. The refined Aspen Plus® model presented in this article needs to be further developed to ensure the standards are attained in all output streams of stabilized anaerobic digestate, biomethane, and isolated added-value chemical fertilizers.

Through a modern derivation of Planck's formula for the entropy of an arbitrary beam of photons we derive a general expression for the entropy production due to the irreversible process of the absorption of an arbitrary incident photon spectrum in material and its dissipation into an infrared-shifted grey-body emitted spectrum, the rest being reflected or transmitted. Employing the framework of Classical Irreversible Thermodynamic theory, we define the generalized thermodynamic flow as the flow of photons from the incident beam into the material and the generalized thermodynamic force is then just the entropy production divided by the photon flow which is the entropy production per unit photon at a given wavelength. We compare the entropy production under sunlight of different inorganic and organic materials (water, desert, leaves and forests) and show that organic materials are the greater entropy producing materials. Intriguingly, plant and phytoplankton pigments (including chlorophyll) have peak absorption exactly where entropy production through photon dissipation is maximal for our solar spectrum $430<\lambda<550$ nm, while photosynthetic efficiency is maximal between 600 and 700 nm. These results suggest that the evolution of pigments, plants and ecosystems has been towards optimizing entropy production rather than photosynthesis. We propose using the wavelength dependence of global entropy production as a biosignature for discovering life on planets of other stars.

Nanotechnology is an emerging field of modern science based on the use of nanoparticles (NPs) with a huge potential in many sectors, including nanomedicine. Their small size confers them unique properties because they are subject to physical laws that are in the middle between classical and quantum physics. In this context, NPs project plays a pivotal role because the composition, size, shape and surface proprieties need to be carefully considered for their optimal design and application. As reported in this review, NPs are classified in inorganic (metallic NPs; quantum dots; carbon-based nanostructures; mesoporous silica nanoparticles) and organic (liposomes and micelles, dendrimers and polymer nanoparticles) ones. Here, we report an accurate description of the potential of each NPs type focusing on their multiple areas of application like theranostics drug delivery, imaging, tissue engineering, antimicrobial techniques and nanovaccines, and therefore they represent a promise to revolutionize the new era of nanomedicine, especially in cancer research.

Soil organic carbon (SOC) is an essential condition for soil health and a potential sink for greenhouse gases. SOC dynamics in a long-term field experiment with mineral and organic fertilization on loamy sand Podzol in Vladimir Region, Russia, was traced with the dynamic carbon model RothC since 1968 until the present time. During this period, C stock increased 21% compared with the initial level in the treatment with the application of manure in an average annual rate of 10 t·ha-1. The model was also used to forecast SOC changes until 2090 for two contrasting RCP4.5 and RCP8.5 climatic scenarios. Until 2090, the steady growth of SOC stocks is expected in all compared treatments for both climate scenarios. This rate of growth was the highest until 2040, decreased in 2040-2070 and increased again in 2070-2090 for RCP4.5. The highest annual gain was within 21-27‰ under RCP4.5 and 16-21‰ in 2020-2040 in 0-20 cm soil layer. The expected accumulation of C allows increasing current C stock 1.6-1.7 times for RCP4.5 and 2.0-2.2 times for RCP8.5 scenario. Modelling demonstrated potentially more favourable conditions for SOC stability in arable Podzols than in Retisols in Central Russia in the 21st century.

This paper introduces a theory for the evolution of corporates in which the growth and sustainability strategies are developed simultaneously. Since the introduction of corporate sustainability, it has been an extra cost for risk mitigation and making ‘compensating’ positive impact. The world has reached a tipping point of volatility, mainly due to climate change but also by emergence of COVID-19, so that the applicability of existing corporate structures is under question and these poses high risk to the existence of our planet. On the other hand, the technology cost for sustainable investment has reached a parity in comparison with non-sustainable alternatives. Therefore, our proposed Organic Grow Theory introduces a step-by-step approach so that corporates can grow and be profitable without compromising the ability of future generations to meet their needs. It is concluded that, a new structure for corporate, called Founcorp, would be needed to direct corporates to evolve being a responsible legal entity.

Various type of soils have been identified based on their electrical and magnetic properties, especially with regards to peat soils. Peat soils are commonly considered as partly decomposed vegetation. In this study, electrical and magnetic properties have been used in K-means clustering to identify layers of peat soils. K-means clustering is a partitioning method that treats observations in the data. Data cores were obtained at every centimeter and examined for their electrical conductivity (σ) and magnetic susceptibility (χ_m) properties. A 291 cm core was obtained at Tegal Arum Village in South Kalimantan, Indonesia. The K-means clustering results indicate two different layers at 148 cm, and this is supported by loss on ignition (LOI) measurements. In the first layers, a 87.65% LOI was found associated with peat soils (above 248 cm). Whereas, in the second layers, there was a 26.11% LOI associated with mineral soils (below 248 cm). The results of this study using K-means clustering can be used to delineate soil layers.

Present worldwide difficulties in healthcare and the environment have motivated the investigation and research of novel materials in an effort to find novel techniques to address the current chal-lenges and requirements. In particular, the use of nanomaterials has demonstrated a significant promise in the fight against bacterial infections and the problem of antibiotic resistance. Metal na-noparticles and carbon-based nanomaterials in particular have been highlighted for their excep-tional abilities to inhibit many types of bacteria and pathogens. In order for these materials to be as effective as possible, synthetic techniques are crucial. Therefore, in this review article, we high-light some recent developments in the design and synthesis of various nanomaterials, including metal nanoparticles (e.g., Ag, Zn, or Cu), metal hybrid nanomaterials, and the synthesis of mul-ti-metallic hybrid nanostructured materials. Following that, examples of these materials’ applica-tions in antimicrobial performance targeted at eradicating multi-drug resistant bacteria, material protection such as microbiologically influenced corrosion (MIC), or additives in construction ma-terials have been described.

The aging mechanism of 10% and 30% nickel substituted manganese hexacyanoferrate cathode material in aqueous zinc-ion batteries has been explored through the advanced synchrotron-based two-dimensional x-ray fluorescence technique. Thanks to the two-dimension modality, not only the metal concentration dynamics throughout the entire electrodes was followed during the aging process, but their spatial distribution was also revealed, suggesting the route of the material transformation. The dissolution of Mn and Ni, and the penetration of Zn inside the framework, alongside the Mn aggregations outside the hexacyanoferrate framework were detected. Additionally, the possibility of conducting x-ray absorption spectroscopy measurements on the regions of interest made it possible to explore the chemical state of each metal, and furthermore, synchrotron-based powder x-ray diffraction demonstrated the gradual structural modification in 30% Ni-containing sample series, in terms of the different phase formation.

The current economic development paradigm, which is based on steadily rising resource consumption and pollution emissions, is no longer viable in a world with limited resources and ecological capacity. The "green economy" idea has presented this context with a chance to alter how society handles the interplay between the environmental and economic spheres. The related concept of "green nanotechnology" aims to use nano-innovations within the fields of materials science and engineering to generate products and processes that are economically and ecologically sustainable, enabling society to establish and preserve a green economy. Many different economic sectors are anticipated to be impacted by these applications, including those related to corrosion inhibitor nano fertilizers, nano remediation, biodegradation, heavy metal detection, biofuel, insecticides & pesticides, and catalytic CO2 reduction. These innovations might make it possible to use non-traditional water sources safely and to create construction materials that are enabled by nanotechnology, improving living and ecological conditions. Therefore, our aim is to highlight how nanotechnology is being used in the green economy and to present promises for nano applications in this domain. Additionally, we want to critically examine the practical difficulties these applications raise, especially in consideration of any possible implications for the health and safety of those employed within this innovative sector. In the end, it emphasizes how critical it is to attain a really sustainable advancement in nanotechnology.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

Metal complexes feature a wide range of available geometries, diversified lability, controllable hydrolytic stability, and easily available rich redox activity. These characteristics combined with the specific properties of the coordinated organic molecules result in many different mechanisms of biological action, making each of the myriads of the classes of metal coordination compounds unique. This focused review presents combined and systematized results of the studies of a group of copper(I) (pseudo)halide complexes with aromatic diimines and tris(aminomethyl)phosphines of a general formula [CuX(NN)PR₃], where X = I^- or NCS^-, NN = 2,2’-bipyridyl, 1,10-phenanthroline, 2,9-dimethyl-1,10-phenanthroline or 2,2’-biquinoline, and PR₃ = Air-stable tris(aminomethyl)phosphines. The structural and electronic properties of the phosphine ligands and luminescent complexes are discussed. The complexes with 2,9-dimethyl-1,10-phenanthroline, apart from being air- and water-stable, exhibit a very high in vitro antimicriobial activity against the Staphylococcus aureus and Candida albicans. Moreover, some of the complexes also show a strong in vitro antitumor activity against human ovarian carcinoma cell lines: MDAH 2774 and SCOV 3, CT26 (mouse colon carcinoma), and A549 (human lung adenocarcinoma) cell lines. The tested complexes are moderately able to induce DNA lesions through free radical processes, however the trends do not reflect observed differences in biological activity.

Metallic substrates and polymer adhesive in composite-metal joints have a relatively large coefficient of thermal expansion (CTE) mismatch, which is a barrier in the growing market of electric vehicles and their battery structures. It is reported that adding carbon nanotubes (CNTs) to the adhesive reduces the CTE of the CNT enhanced polymer adhesive multi-material system, therefore when used in adhesively bonded joints it would, theoretically, result in low CTE mismatch in the joint system. The current article presents the influence of two specific mass ratios of CNTs on the CTE of the enhanced polymer. It was observed that the addition of 1.0 wt% and 2.68 wt% of multi-walled CNTs (MWCNTs) decreased the CTE of the polymer adhesive from 7.5e-5 1/C (pristine level) to 5.87e-5 1/C and 4.43e-5 1/C, respectively by 22% and 41% reduction. The reduction in the CTE was predicted, theoretically, which showed that CTE should have been reduced to 3.6e-5 1/C (52% reduction) and 1.4e-5 1/C (81% reduction). This may be due to the fact that, Raman spectroscopy of the MWCNTs identified defects in the raw material, and scanning electron microscopy (SEM) identified agglomeration of MWCNTs on the surface and cross-section of the modified polymers.

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser-wire based Directed Energy Deposition is demonstrated with a novel modification: site-specific changes to the controller set-point were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary 3D-printed component geometry. The present work shows that, through this technique, it is possible to print a specific geometry that occurs beyond the actual toolpath of the print head. This is denoted as an extra-toolpath geometry and is fundamentally different from other methods of generating component features in metal AM. A proof-of-principle experiment is presented in which a complex oak leaf geometry was embossed on an otherwise ordinary double-bead wall made from Ti-6Al-4V. The process is introduced and characterized primarily from a controls perspective with reports on the performance of the control system, the melt pool size response, and the resulting geometry. The implications of this capability, which extend beyond localized control of bead geometry to the potential mitigations of defects and functional grading of component properties, are discussed.

The blue sepal color of hydrangea is due to a metal complex anthocyanin composed of 3-O-glucosyldelphinidin (1) and an aluminum ion with the co-pigments 5-O-caffeoylquinic acid (2) and/or 5-O-p-coumaroylquinic acid (3). The three components, namely, anthocyanin, Al³⁺ and 5-O-acylquinic acids, are essential for blue color development, but the complex is unstable and only exists in aqueous solution. Furthermore, the complex did not give analyzable NMR spectra or crystals. Therefore, many trials to determine the detailed chemical structure of the hydrangea-blue complex have failed to date. Instead, via experiments mixing 1, Al³⁺ and 2 or 3 in a buffered solution at pH 4.0, we obtained the same blue solution derived from the sepals. However, the ratio was not stoichiometric but fluctuated. To determine the composition of the complex, we tried direct observation of the molecular ion of the complex using electrospray-ionization mass spectrometry. In a very low-concentration buffer solution (2.0 mM) at pH 4.0, we reproduced the hydrangea-blue color by mixing 1, 2 and Al³⁺ in ratios of 1:1:1, 1:2:1 and 1:3:1. All solution gave the same molecular ion peak at m/z = 843, indicating that the blue solution has a ratio of 1:1:1 for the complex. By using 3, the observed mass number was m/z = 827 and the ratio of 1, 3 and Al³⁺ was also 1:1:1. A mixture of 1, 3-O-caffeoylquinic acid (4) and Al³⁺ did not give any blue color but instead was purple, and the intensity of the molecular ion peak at m/z = 843 was very low. These results strongly indicate that the hydrangea blue-complex is composed of a ratio of 1:1:1 for 1, Al³⁺ and 2 or 3.

2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) is a molecule widely employed as a very effective p-dopant of semi-conducting polymers, such as poly(3-hexylthiophene -2,5-diyl) (P3HT). The CN stretching transitions of F4TCNQ are exceptionally sensitive to the charge state of the molecule, thus allowing the doping diagnosis via IR spectroscopy. Less pronounced frequency shifts can reveal characteristics of the intermolecular environment. We present a systematic study based on Density Functional Theory (DFT) calculations and on experiments aimed at exploring how different factors, such as the charge state and the environment, modify the vibrational spectra of F4TCNQ. While several effects on the vibrational frequencies are well known and have been thoroughly investigated in the past, this study focuses on the infrared intensities of the CN stretching modes and reveals that they are strongly affected both by the charge state of the molecule and by the surrounding medium: it is then mandatory to consider such remarkable intensity modulation for any quantitative diagnosis based on spectroscopic measurements, e.g., concerning the amount of F4TCNQ molecules involved in the formation of charge transfer complexes.

Several environmental and economic issues have been brought about by mass accumulations of Sargassum along the coastlines in Trinidad and Tobago, and the wider Caribbean region. Though there are massive environmental issues associated with this seaweed biomass, there is also a chance to make innovations, thereby making this problem into a solution. The holopelagic species such as S. natans and S. fulitans have considerably high amounts of beneficial compounds which can be leveraged for agriculture. The value chain transformation of Sargassum from a nuisance to a resource for agricultural production is narrated in the following report. Details of the application of products from Sargassum including composts, soil amendments, and liquid biostimulants are given. A case study is presented for OJA1 biostimulant, which was developed from Sargassum biomass at the University of the West Indies, St. Augustine, Trinidad. This biostimulant has shown increased productivity and resistance to diseases of several cash crops. The valorization of Sargassum contributes to sustainable agriculture and propels economic development in coastal communities. The Caribbean could lead with the adoption of the circular economy, turning environmental adversity into a lever for sustainable development.

Crop rotation diversification using legumes has been advocated as one of the solutions to improve the resilience of the crop system to various environmental stresses and the use of nitrogen resources. However, when forage legumes or grass-legumes are ploughed, there is a high risk of nitrate leaching, especially in sandy soils. The aim of the study was to determine the effect strip tillage intercropping management on soil mineral nitrogen (SMN), water-extractable organic carbon (WEOC) content and winter wheat (WW, Triticum aestivum L.) grain yield compared to forage legume and WW monocropping with conventional tillage. In intercropping was used winter wheat - black medick (Medicago lupulina L.) WW+BM, winter wheat - white clover (Trifolium repens L.) WW+WC, and winter wheat - Egyptian clover (Trifolium alexandrinum L.) WW+EC. Research was repeated in two experiments. The results showed that after strip tillage and WW sowing less or similar SMN content cud be detected, as in conventional tillage and WW + forage legumes intercropping. WW grain yield in intercrops decreased, compared to the grasses monocultures that were ploughed before WW sowing. The highest amount of WEOC was in intercropping soil growing WW+WC or in all fields (except WW+EC) after applying strip tillage. During the research period, the amounts of mobile humic substances (HSs) and mobile humic acids (HAs) changed analogously. Their content increased substantially in fields with WC and EC, regardless of whether the grasses were ploughed or grown with WW.

The adoption of environmental conservation agriculture (ECA) in Nepal is aligned with the country's goal to achieve carbon neutrality by 2045, as ECA practices have been proven to effectively reduce greenhouse gas emissions. Nepal's agricultural sector faces numerous challenges, including labor shortages, climate change impacts, and the necessity for environmentally friendly farming methods, making the adoption of ECA practices even more crucial. This paper thus explored farmer perspectives on the sustainability of ECA practices in Namobuddha municipality, Nepal, which is renowned as a leading hub of organic farming. A cross-sectional survey was conducted, together with key informant interviews and onsite observations. By analyzing various farmer perspectives, the study presents an analytical framework that highlights the economic, environmental, and social pillars of ECA's sustainability. The findings underscore the significance of economic viability for farmers, as damages to crops and farm products negatively drive their perception of ECA sustainability. Conversely, factors such as increased agriculture-related income, favorable prices, and sustainable productivity positively shape farmers' perceptions. In terms of environmental sustainability, farmers prioritize enhancing the local and global environment, viewing their farming methods as climate-smart and actively working towards reducing greenhouse gas emissions. The study emphasizes the importance of strategic communication to effectively convey the benefits of ECA to rural communities. Overall, this research contributes to filling the knowledge gap concerning farmers' perceptions of ECA sustainability. The insights gained from this study have the potential to inform policy decisions and promote the widespread adoption of environmentally friendly farming practices in Nepal.

Organic light-emitting diodes (OLEDs) have garnered considerable attention in academic and industrial circles due to their potential applications in flat panel displays and solid-state lighting technologies, leveraging the advantages offered by organic electroactive derivatives over their inorganic counterparts. The thin and flexible design of OLEDs enables the development of innovative lighting solutions, facilitating the creation of customizable and contoured lighting panels. Among the diverse electroactive components employed in the molecular design of OLED materials, the benzophenone core has attracted much attention as fragment for synthesis of organic semiconductors. On the other hand, the benzophenone also functions as a classical phosphor with high intersystem crossing efficiency. This characteristic makes it as compelling candidate for effective reverse intersystem crossing, potentially leading to the development of thermally activated delayed fluorescent (TADF) emitters. These emitting materials witnessed a pronounced interest in recent years due to their incorporation in metal-free electroactive frameworks and the capability to convert triplet excitons into emissive singlet excitons through reverse intersystem crossing (RISC), consequently achieving exceptionally high external quantum efficiencies (EQEs). This review article comprehensively overviews the synthetic pathways, thermal characteristics, electrochemical behaviour and photo-physical properties of the derivatives based on benzophenone. Furthermore, we explore their applications in OLED devices, both as host materials and emitters, shedding light on the promising opportunities that benzophenone-based compounds present in advancing OLED technology.

Biochar is a carbon-rich material that recently received attention due to its increasing agronomical potential. The agricultural utilization of biochar relates to its potential to act in the soil as a soil conditioner, nevertheless, the complex information on the direct dependence of biochar physical properties (texture, particle size) and corresponding leaching and availability of organic molecules (e.g. the polycyclic and heterocyclic organic compounds) and inorganic mineral salts (based on micro– and macroelements) are still not consistent. These aspects were addressed in our study. A multi-elemental analysis (ICP-OES) was used to access the information on the aqueous-extractable and total contents of inorganic macro- and macroelements in used commercial biochar samples (purchased from Sonnenerde GmbH, Novoterrra Sonnenerde GmbH, Biouhel.cz, s.r.o.). Potassium (K) was identified as the major macroelement, responsible for alkaline pH and the conductivity of biochar extract. Our results indicate an indirect relation between the size fraction of biochar and the content of extractable K, sodium (Na), and calcium (Ca) and a direct relation with the contents of phosphorus (P) and magnesium (Mg). As the total determined amounts of inorganic elements were significantly higher compared to aqueous-extractable amounts, we believe it could indicate the potential for repeated release to the surrounding soil. These findings were also confirmed by the analysis of biochar samples obtained after the cultivation (duration of 2 years) in selected representative soil samples from the Czech Republic (Cambisol, Fluvisol, Regosol, Chernozem). Moreover, gas chromatography (GC) coupled with mass spectroscopy (MS) was further used to reveal the concentrations of available polycyclic aromatic and heterocyclic compounds in biochar samples. The detected concentration of these types of organic compounds were far below the certified limits. We believe our in-depth analysis could provide the necessary insight into the description of biochar mineral content, its connection to biochar texture, corresponding physicochemical properties and potential availability to leach nutrients to the soil. These findings could help in further assessment of the potential applications of biochar in modern agriculture as a soil conditioner.

Retrogressive thaw slumps (RTSs) are becoming more common on the Qinghai-Tibet Plateau as permafrost thaws, but the hydraulic characteristics of these slumps have not been extensively studied. To fill this knowledge gap, we used the ''space-for-time substitution method'' to differentiate three stages of RTSs: original grassland, collapsing, and collapsed. Our study included on-site investigations, measurements, and simulated analyses of soil water characteristics, environmental factors, and hydrological properties. Our findings show that the measurements and simulated analyses of soil water characteristics were highly consistent across RTSs, indicating the accuracy of the V-G model in reproducing soil hydraulic parameters for different stages of RTSs. The original grassland stage had the highest soil water retention and content due to its high SOM content and fine-textured micropores. In contrast, the collapsed stage had higher soil water retention and content compared to the collapsing stage, primarily due to increased proportions of soil micropores, SOM content, and lower bulk density (BD). Freeze-thaw cycles had a significant impact on the soil texture and structure of RTSs, resulting in a decrease in SOM content and an increase in BD. However, the absence of soil structure and compaction led to the subsequent accumulation of organic matter, increasing SOM content. Changes in field capacity (FC), permanent wilting point (PWP), and soil micropore distribution aligned with variations in SOM content and water content.These findings highlight the importance of managing SOM content and water content to mitigate the adverse effects of freeze-thaw cycles on soil structure and stability at different stages of RTSs. Effective management strategies may include incorporating organic matter, reducing soil compaction, and maintaining optimal water content. Further research is needed to determine the most suitable management practices for different soil types and environmental conditions.

Emerging pollutants pose significant threats to Uganda's ecosystems and public health amidst rapid urbanization, industrial growth, and intensified agriculture. This systematic review comprehensively assessed these pollutants by analyzing existing Ugandan literature and research studies, revealing various types in different environmental compartments. These pollutants, including pharmaceuticals, personal care products, pesticides, industrial chemicals, heavy metals, radionuclides, biotoxins, disinfection byproducts, hydrocarbons, and microplastics, originate from urban, industrial, and agricultural regions. Wastewater and improper waste disposal are major contributors. From an initial search of 794 articles across multiple databases such as PubMed, African Journal Online (AJOL), Web of Science, Science Direct, and Google Scholar, 138 were found relevant. The review underscores potential ecological and health impacts, including antibiotic resistance, endocrine disruption, and carcinogenicity. Existing monitoring and regulation efforts are discussed, alongside the need for specific regulations, improved data collection, and public awareness campaigns. Recommendations include advanced wastewater treatment, sustainable agriculture, and source control measures. Emphasis is placed on further research to address knowledge gaps and develop effective policies and interventions. Uganda can mitigate these risks by implementing comprehensive monitoring, robust regulations, and sustainable practices, safeguarding the environment and public health.

Hydrochemical and geophysical data collected during a hydrological survey in September 2017, reveal patterns of small-scale hydrological connectivity in a small water track catchment, north-European Arctic. Elevated tundra patches underlain by sands were disconnected from the stream and stored precipitation water from previous months. At the catchment surface and in the water track thalweg, some circular hollows, from 0.2 to 0.4 m in diameter, acted as evaporative basins with low d-excess values, from 2 to 4‰. Other hollows were connected to shallow subsurface runoff, yielding d-excess values between 12 and 14‰. ‘Connected’ hollows yielded a 50% higher dissolved organic carbon (DOC) content, 17.5±5.3 mg/L, than the ‘disconnected hollows, 11.8±1.7 mg/L. Permafrost distribution across the landscape is continuous, but highly variable. Open taliks exist under fens and small hummocky depressions, as revealed by electric resistivity tomography surveys. Isotopic evidence supports upward subpermafrost groundwater migration through open taliks under water tracks and fens/bogs/depressions, and its supply to streams via shallow sub-surface compartment. Temporal variability of isotopic composition and DOC in water track and a major river system, the Vorkuta R., evidence the widespread occurrence of the described processes in the large river basin. Water tracks effectively drain the tundra terrain and maintain xeric veg-etation over the elevated inter-track tundra patches.

Optical rotatory dispersion (ORD) is a beautiful analytical technique for the study of chiral molecules and polymers. In this study, ORD was applied successfully to follow the degree of polycondensation of l-(+)-lactic acid toward the formation of poly(lactic acid) oligomers (PLAO) and high molecular weight poly(l-lactic acid) (PLLA) in a simple esterification reaction equipment. PLLA is a biodegradable polymer obtainable from renewable raw materials. The racemization of the intrinsically isotactic PLLA through thermal treatment can be easily followed through the use of ORD spectroscopy. Organic or molecular electronics is a hot topic dealing with the combination of π-conjugated organic compounds and polymers with specific properties (e.g. chirality) which can be exploited to construct optoelectronic devices such as organic light-emitting diodes (OLEDs), organic photovoltaic (OPV) high efficiency cells, switchable chirality devices, organic field-effect transistors (OFETs), and so on. ORD spectroscopy was applied to study either the gigantic optical rotation of PLLA films as well as to detect successfully the excitonic coupling occurring in thin solid PLLA green film loaded with a combination of two dyes: SY96 (a pyrazolone dye) and PB16 (the metal-free phthalocyanine pigment). The latter compound PLLA loaded with SY96 and PB16 shows a really gigantic optical activity in addition to typical ORD signal due to exciton coupling and may be considered as a simple and easily accessible model composite of a chiral polymer matrix combined with π-conjugated dyes for molecular electronics studies.

Succinic semialdehyde dehydrogenase deficiency (SSADH-D) is a genetic disorder that results from the aberrant metabolism of the neurotransmitter γ-amino butyric acid (GABA). The disease is caused by the impaired activity of the mitochondrial enzyme succinic semialdehyde dehydrogenase. SSADH-D manifests as varying degree of mental retardation, autism, ataxia and epileptic seizures, but the clinical picture is highly heterogeneous. So far, there is no approved therapy for this disease. In this review, we briefly summarize the molecular genetics of SSADH-D, the past and ongoing clinical trials and the emerging features of the molecular pathogenesis, including redox imbalance and mitochondrial dysfunction. The main aim of this review is to discuss the potential use of further therapy approaches that have so far not been tested in SSADH-D, such as pharmacological chaperones, read-through drugs and gene therapy. Special attention will also be paid to elucidating the role of patient advocacy organizations in facilitating research and in the communication between the researchers and the patients.

Induction of jasmonate-mediated plant defense against insect herbivory is initiated by a combination of both, mechanical wounding and chemical factors. In order to study both effects independently on plant defense induction, SpitWorm, a computer-controlled device which mimics the damage pattern of feeding insect larvae on leaves and, in addition, can apply oral secretions (OS) or other solutions to the ‘biting site’ during ‘feeding’, was developed and evaluated. The amount of OS left by a Spodoptera littoralis larva during feeding on Phaseolus lunatus (lima bean) leaves was estimated by combining larval foregut volume, biting rate, and quantification of a fluorescent dye injected into the larvae’s foregut prior to feeding. For providing OS amounts by SpitWorm equivalent to larval feeding, dilution and delivery rate were optimized. The effectiveness of SpitWorm was tested by comparing volatile organic compounds (VOC) emissions of P. lunatus leaves treated with either SpitWorm, MecWorm or S. littoralis larvae. Identification and quantification of emitted VOCs revealed that SpitWorm induced a volatile bouquet that is qualitatively and quantitatively similar to herbivory. Additionally, RT-qPCR of four jasmonic acid responsive genes showed that SpitWorm, in contrast to MecWorm, induces the same regulation pattern as insect feeding. Thus, SpitWorm mimics insect herbivory almost identical to real larvae feeding.

The acylation of unsymmetrical N-benzylbispidinols in aromatic solvents without external base led to formation of supramolecular gels, which possess different thickness and stability depending on the substituents in para-positions of benzylic group and nature of acylating agent as well as on the nature of the solvent used. Structural features of the native gels as well as of their dried forms were studied by complementary techniques including FT IR- and ATR-spectroscopy, AFM, TEM, SEM, SAXS. Structures of the key crystalline compounds were established by X-ray diffraction. Analysis of obtained data allowed speculating on the crucial structural and condition factors that governed the gel formation. The most important factors were: (i) absence of base, either external or internal; (ii) presence of HCl; (iii) presence of carbonyl and hydroxyl groups to allow hydrogen bonding; (iv) presence of two (hetero)aromatic rings at both sides of the molecule. The hydrogen bonding involving amide carbonyl, hydroxyl at 9th position and, very probably, ammonium N-H+ and Cl- anion appear to be responsible for the formation of infinite molecular chains required for the first step of gel formation. Subsequent lateral cooperation of molecular chains into fibers occured, presumably, due to the aromatic pi-pi-stacking interactions. sc-CO2 drying of the gels gave rise to aerogels morphology different from that of air dried samples.

The ANFC/ABPE-10 composite film was prepared by ABPE-10 impregnating into ANFC films under negative pressure. And the composite film had meted high performance FOLED substrate requirement even when ANFC dosage was high for approximately 70%, which was consistent with for low cost efficiency, recyclability, and environmentally friendly. The enhanced properties of ANFC films were mainly because of the nature of ABPE-10 itself and the IPN structure formed between ABPE-10 and ANFC film. The transparency of composite films with different ANFC dosage was significantly increased from 67% to 88% by UV-Vis analysis. The composite film inherited the properties of AFNC, obtaining low CTE characteristics and ductile compact structure. The contact angles of ANFC films increased by 102% from 49.2° to 102.9°after dipping ABPE-10. Additionally, the composite films had outstanding mechanical properties such as tensile strength 173.72 MPa, Young’s modulus 4.06 GPa, and elongation at break 5.81%.

Aluminium matrix composite’s overall quality is impacted by the friction stir process parameters, which have a major impact on the microstructure, soundness, and particle dispersion inside the stir zone. Although it requires a lot of experimentation, optimizing these factors is vital. For the purpose of optimizing the ultimate tensile strength and microhardness of the AA5083/Silicon carbide and AA5083/Coal composites fabricated by FSP, this work used the Taguchi L9 design of experiments. Three process parameters were investigated at three levels each. For the AA5083/Silicon carbide composite, the results of the ANOVA analysis showed rotational speed has a larger impact on ultimate tensile strength while forAA5083/coal tilt angle has a larger impact on ultimate tensile strength. On the other hand, rotating speed had a greater effect on microhardness and percentage elongation of the AA5083/Coal and AA5083/Silicon carbide composite joints, according to ANOVA analysis. The need for specific process optimization for each composite was highlighted by the fact that different combinations of parameters were best for obtaining the necessary attributes in the AA5083/Silicon carbide and AA5083/Coal composites.

Geothermal energy is a weather-independent, permanently available renewable energy source. In addition to producing heat and electricity, geothermal energy can be used to extract critical raw materials dissolved in the heat-carrying fluid. Researchers working on the frontiers of geothermal energy utilisation may be able to transform ultra-deep metallic mineral formations into “orebody-Enhanced Geothermal Systems”. In the planned technology, the metal-containing geological formation would be manipulated in such a way that cogeneration of energy and metals is possible and can be optimised in the future according to market needs. The potential of geothermal energy for sustainable mineral extraction and energy production aligns with Sustainable Development Goal (SDG) 7, which aims to ensure access to affordable, reliable, sustainable, and modern energy for all. This new technology could substantially decrease Europe’s dependency on importing critical metallic minerals (such as lithium and tungsten) and energy; over and above, it has a small environmental footprint, including very low carbon emissions

The interlaminar strength of mechanically interlocked polymer-metal-interfaces is strongly dependent on the surface structure of the metal component. Therefore, this contribution assesses the suitability of the fractal dimension for quantification of the surface structure as well as interlaminar strength prediction of aluminum/polyamide 6 polymer-metal-hybrids. Seven different surface structures, manufactured by blasting, combined blasting and etching, thermal spraying and laser ablation, are investigated. The experiments are carried out on a novel butt-bonded hollow cylinder testing method that allows shear and tensile strength determination with one specific specimen geometry. The fractal dimension of the metal surfaces is derived from cross-sectional images. For comparison, the surface roughness slope is determined and related to the interlaminar strength. Finally, a fracture analysis is conducted. For the investigated material combination, the experimental results indicate that the fractal dimension is an appropriate measure for predicting the interlaminar strength

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Promoting organic foods production and consumption contributes to accomplishing United Nations sustainable development goals. Social commerce provides a promising opportunity to develop the organic food industry. However, there is limited knowledge regarding customer behaviors in relation to purchasing organic foods via social commerce platforms. Therefore, this study expanded upon the unified theory of acceptance and use of technology (UTAUT-2) to develop a comprehensive model that explains how customers' social commerce trust and behavioral intentions to purchase organic foods using Instagram social commerce affect their purchasing behaviors. The research model was analyzed by employing partial least squares structural equation modeling (PLS-SEM) for the data collected from a quantitative survey of 410 customers who used Instagram to purchase organic foods in Iran. The results revealed that facilitated purchasing conditions, hedonic motivations, social influence, rating and reviews, and influencers’ endorsements increase customers' purchase intentions. Moreover, Instagram’s recommendations and referrals, influencers’ endorsements, as well as social influence boost customers' trust in the social commerce platform. Eventually, it was determined that influencers’ endorsements, social commerce trust, and purchase intention determine a customer’s organic foods purchasing behaviors. This research provides valuable insights for organic food marketers to optimize their social commerce strategies.

Radical reactions in water or aqueous media are important for organic synthesis, realizing high yielding processes under non-toxic and environmentally friendly conditions. This overview includes (i) a general introduction to organic chemistry in water and aqueous media, (ii) synthetic approaches in-, on- and with-water as well as in heterogeneous phase, (iii) reaction of carbon-centered radicals with water (or deuterium oxide) activated through coordination with various Lewis acids, (iv) photocatalysis in water and aqueous media, and (v) synthetic applications bioinspired from naturally occurring processes. A wide range of chemical processes and synthetic strategies under different experimental conditions have been reviewed that lead to important functional group translocation and transformation reactions, leading to the preparation of complex molecules. These results reveal how water as a solvent/medium/reagent in radical chemistry has matured over the last two decades and how further discoveries are foreseen to come in the near future.

Photophysics properties such as fluorescence quenching, and photoexcitation dynamics of bimolecular non-covalent systems consisting of cationic poly[(9,9-di(3,3’-N,N’-trimethyl-ammonium) propyl fluorenyl-2,7-diyl)-alt-co-(9,9-dioctyl-fluorenyl-2,7-diyl)] diiodide salt (PFN) and anionic graphene carboxylate (GC) have been discovered for the first time by the steady state and time-resolved femtosecond transient absorption (TA) spectroscopy with broadband capabilities. The steady-state fluorescence of PFN is quenched with high efficiency by GC acceptor. Fluorescence lifetime measurements revealed that the quenching mechanism of PFN by GC is static. Here, the quenching mechanisms are well proven by TA spectra of PFN/GC systems. For PFN/GC systems, the photo electron transfer (PET) and charge recombination (CR) processes are ultrafast (within few tens of ps) related to static interactions whereas for PFN/DCB systems the PET takes place in few hundreds ps (217.50 ps)1 suggesting diffusion-controlled PET process. In the latter case, the PFN+•-DCB-• radical ion pairs as the result of PET from the PFN to DCB are clearly resolved and they are long-lived. The slow CR process (in 30 ns time scales)1 suggest PFN+• and DCB-• may already form separated radical ion pairs through charge separation (CS) process, which recombined back to the initial state with a characteristic time constant of 30 ns. The advantage of the present positively charged polyfluorene used in this work is the control over the electrostatic interactions and electron transfers in non-covalent polyfluorene/quencher systems in DMSO solution.

Plant waste biomass is the most abundant renewable energy resource on Earth. The main problem of utilising this biomass in anaerobic digestion is the long and costly stage of degrading its complex structure into simple compounds. A promising solution to this problem are fungi of the Trichoderma genus, which show a high capacity to produce hydrolytic enzymes capable of degrading lignocellulosic biomass. This article discusses the structure of plant waste biomass and the problems resulting from its structure in the digestion process. It presents the methods of pre-treatment of lignocellulose with a particular focus on biological solutions. Based on the latest research findings, key parameters related to the application of Trichoderma sp. as a pre-treatment method are discussed. In addition, the possibility of using the digestate from agricultural biogas plants as a carrier for the multiplication of the Trichoderma sp. fungi, which are widely used in many industries, was discussed.

Organic light-emitting diodes (OLEDs) have ushered in a technological revolution with their remarkable impact on diverse sectors of our daily lives. These versatile devices known for their outstanding display and lighting capabilities, have become indispensable components in various industries including smartphones, tablets, televisions, and automotive applications. This paper delves into the development of a group of twisted donor-acceptor-donor (D-A-D) derivatives incorporating bicarbazole and benzophenone structures for potential use as blue emitters in OLEDs. The synthesized compounds, namely DB14, DB23 and DB29, were designed with various alkyl side chains to enhance their film forming properties as for blue emitters. Characterization and evaluation of these derivatives included photophysical, electrochemical, thermal, and electroluminescent analysis. Some of the OLED devices incorporating these emitters demonstrated promising performance with maximum current efficiency (CEmax) of 2.6 cd/A and external quantum efficiency (EQEmax) of 5.3%. Notably, the DB23 emitter exhibited the highest EQE among all devices. The study also emphasizes the influence of host-guest energy transfer, optimal doping concentrations, and molecular structures on device performance. This research not only contributes to the understanding of advanced OLED materials but also provides insights into designing efficient blue emitters for future display and lighting applications, thereby advancing the field of organic electronics.

Diabetes mellitus is a widespread chronic metabolic disorder demanding regular blood glucose level surveillance (BGLs). Current invasive techniques, such as finger-prick tests, often result in discomfort for patients, leading to infrequent monitoring and potential health complications. The primary objective of this study was to design a novel, portable, non-invasive system for diabetes detection using breath samples, named as DiabeticSense, an affordable digital health device for early detection, encouraging immediate intervention. The device employed MOSFET-based electrochemical sensors to assess volatile organic compounds in breath samples, whose concentrations differ between diabetic and non-diabetic individuals. The system merged body vital signs with sensor voltages obtained by processing breath sample data to predict diabetic conditions. Our research used readings from 100 patients at a nationally recognised hospital to form the dataset. Data was then processed 10 using a Gradient Boosting Classifier model, and performance was cross-validated. The proposed system attained a promising accuracy of 86.6%, marking an improvement of 20.72% over an existing regression technique. The developed device introduces a non-invasive, cost-effective, and user-friendly solution for preliminary diabetes detection. It has the potential to increase patient adherence to regular monitoring.

Organic light-emitting diodes (OLEDs) are energy-efficient; however, the coordinating ligand can affect their stability. Sky-blue phosphorescent Pt(II) complexes with a C^N chelate, fluorinated-dbi (dbi = [1-(2,4-diisopropyldibenzo[b,d]furan-3-yl)-2-phenyl-1H-imidazole]), and acetylactonate (acac)(1)/picolinate (pic)(2) ancillary ligands were synthesized. The molecular structures were characterized using various spectroscopic methods. The Pt(II) coordination sphere in 2 exhibited a distorted square-planar geometry, with several intra- and inter-molecular interactions involving Cπ⋯H/Cπ⋯Cπ stacking. Complex 1 emitted bright sky-blue light (λmax = 485 nm) with a moderate photoluminescent quantum efficiency of 0.37 and short decay time (6.1 µs) compared to those of 2. Time-dependent density functional theory calculations suggested that the electronic transition of 1 arose from ligand(C^N)-centered π–π* transitions combined with metal-to-ligand charge transfer transitions (MLCT), whereas that of 2 arose from MLCT and ligand(C^N)-to-ligand(pic) charge transfer (LLCT), with minimal contribution from the C^N chelate to the lowest unoccupied molecular orbital. Multi-layered phosphorescent OLEDs using 1 as a dopant and a mixed host, 3,3-di(9H-carbazol-9-yl)-1,1-biphenyl:3-di(9H-carbazol-9-yl)-1,1-biphenyl (mCBP)/9-(3’-carbazol-9-yl-5-cyano-biphenyl-3-yl)-9H-carbazole-3-carbonitrile (CNmCBPCN) were successfully fabricated. At a 10% doping of 1, a current efficiency of 13.6 cd A−1 and external quantum efficiency of 8.4 % at 100 cd m−2 were achieved. These results show that the ancillary ligand in phosphorescent Pt(II) complexes must be considered.

Unmetamorphosed carbonaceous chondrites provide important information concerning the formation and evolution of organic matter, such as amino acids. However, terrestrial contamination remains a valid concern when investigating the organic inventory of meteorites that have fallen to Earth. Accordingly, JAXA’s Hayabusa2 and NASA’s OSIRIS-REx have been launched with the task of returning uncontaminated C-type asteroid material to Earth. The successful Hayabusa2 mission has a very limited sample size (5.4 g). Therefore, many conventional compound specific techniques will struggle to detect amino acids above detection limit with available sample amounts (~several mg to 10’s of mg) being much smaller than those typically used. Here a novel method utilizing ultrahigh performance liquid chromatography-Orbitrap-mass spectrometry is validated and applied to very small meteorite samples, thus providing an approach that can overcome the small sample size constraints of sample return missions. The method is highly sensitive, enabling the detection of amino acids in the carbonaceous chondrites Murchison (2.28 mg) and Orgueil (2.30 mg). Furthermore, quantitation was possible for many of the detected amino acids in Murchison and Orgueil. Using the data presented here, both the amino acid reservoirs of Murchison and Orgueil and the potential application of this method to sample return samples are discussed.

Trichoderma atroviride is a strong necrotrophic mycoparasite antagonizing and feeding on a broad range of fungal phytopathogens. It further beneficially acts on plants by enhancing growth in root and shoot and inducing systemic resistance. Volatile organic compounds (VOCs) are playing a major role in all those processes. To date, T. atroviride IMI 206040 and T. atroviride P1 are among the most frequently studied T. atroviride strains and hence are used as model organisms to study mycoparasitism and photoconidiation. However, there are no studies available, which systematically and comparatively analyzed putative differences between these strains regarding their light-dependent behavior. We therefore explored the influence of light on conidiation and the mycoparasitic interaction as well as the light-dependent production of VOCs in both strains. Our data show that in contrast to T. atroviride IMI 206040 conidiation in strain P1 is independent of light. Furthermore, significant strain-and light-dependent differences in the production of several VOCs between the two strains became evident, indicating that T. atroviride P1 could be a better candidate for plant protection than IMI 206040.

Human-Computer Interaction, including technology-aided instruction, is beginning to focus on virtual reality (VR) technology due to its ability to support immersive learning, teaching through simulation, and gamification of learning. These systems can deliver high-level multisensory learning experiences that are important in the teaching of many subjects, especially those involving abstract concepts or requiring spatial skills, such as organic chemistry. Haptic experiences with VR, however, remain a challenge. In addition, development have focused on general entertainment/gaming; VR systems in chemistry implement simulations of the chemistry laboratory and other advanced systems whereas those that support safe, game-like, immersive and multisensory learning of organic chemistry with haptics at pre-university education levels are scarce. We developed the VR Multisensory Classroom (VRMC) as an immersive learning environment within a VR head-mounted display, where learners employ hand movements to build hydrocarbon molecules and experience haptic feedback through gloves with built-in sensors and hand-tracking with the Leap Motion system. We report here the evaluation of the first prototype by learners from diverse backgrounds who reported on the ability of the VRMC to support high engagement, motivation, interest and organic chemistry learning as well as diverse learning styles. The VRMC is a novel VR classroom that supports immersive learning in molecular organic chemistry with haptics for multisensory learning.

The strength of laser joined metal and plastic hybrids is based purely on adhesion. Unpolar plastics like polypropylene depend solely on the mechanical adhesion while polar plastics like polyamide 6.6 develop covalent bonds with the metal. In this research the influence of different surface metallizations on the lap shear strength of laser joined hybrids was investigated. Sandblasted AISI 304 was used as base metal and reference. Aluminum and titanium coatings were deposited by the means of Arc-PVD. Polypropylene and polyamide 6.6 were utilized as polar und unpolar plastics. The lap shear strength of all hybrids with polyamide 6.6 was higher than the polypropylene samples. For all investigated variations of the laser power, scanning speed and the cohesive and adhesive failure modes, the samples joined with the sandblasted AISI 304 showed the highest lap shear strength. The reduction in lap shear strength for the coated samples was due to the increased difference in thermal conductivity between the plastics and the coating materials. This lead to increased warping and residual stresses. It can be concluded that the thermal properties of the metallization in laser joined metal and plastic hybrids has a high impact on the lap shear strength.

Structure and reversibility of cross-link junctions play pivotal roles in deter- mining the nature of thermoreversible gelation and dynamic mechanical prop- erties of the produced polymer networks. We attempt to explore new types of sol–gel transitions with mechanical sharpness by allowing cross-links to grow without upper bound. We consider thermoreversible gelation of the primary molecules R{Af} carrying the number f of low molecular weight functional groups (gelators) A. Gelators A are assumed to form supramolecular assemblies. Some examples are: telechelic polymers (f = 2) carrying π–π stacking benzene derivatives at their both ends, trifunctional star molecules (f = 3) bearing mul- tiple hydrogen-bonding gelators. The sol–gel transition of the primary molecules becomes sharper with the cooperativity parameter of the stepwise linear growth of the cross-links. There is a polymerization transition (crossover without singu- larity) of the junctions in the postgel region after the gel point is passed. If the gelator A tends to form supramolecular rings competitively with linear chains, there is another phase transition in the deep postgel region where the average molecular weight of the rings becomes infinite (Bose-Einstein condensation of rings). As a typical example of binary cross-links where gelators A and B form mixed junctions, we specifically consider metal-coordinated binding of ligands A by metal ions B. Two types of multi-nuclear supramolecular complexes are studied: (i) linear stacking (ladder) of the sandwich A2B units, (ii) linear train of egg-box A4B units. The average molecular weight, the gel fraction, the av- erage length of the cross-link junctions are calculated for all of these models as functions of the functionality f, the concentration of the solute molecules, and temperature. Potential candidates for the realization of these new types of thermoreversible gelation are discussed.

Interviews from strength and conditioning coaches across all levels of athletic competition identified their two biggest concerns with the current state of wearable technology: (a) the lack of solutions that accurately capture data "from the ground up" and (b) the lack of trust due to inconsistent measurements. The purpose of this research is to investigate the use of liquid metal sensors, specifically Liquid Wire sensors, as a potential solution for accurately capturing ankle complex movements such as plantar flexion, dorsiflexion, inversion, and eversion. Sensor stretch linearity was validated using a Micro-Ohm Meter and a Wheatstone bridge circuit. Sensors made from different substrates were also tested and discovered to be linear at multiple temperatures. An ankle complex model and computing unit for measuring resistance values were developed to determine sensor output based on simulated plantar flexion movement. The sensors were found to have a significant relationship between the positional change and the resistance values for plantar flexion movement. The results of the study ultimately confirm the researchers' hypothesis that liquid metal sensors, and Liquid Wire sensors specifically, can serve as a mitigating substitute for inertial measurement unit (IMU) based solutions that attempt to capture specific joint angles and movements.

To date the role of green leaf volatiles has been mainly constrained to their role in protecting plants against pests and pathogens. However, increasing evidence suggests that among the stresses that can significantly harms plants, GLV can also provide significant protection against an array of those including heat, cold, drought, light, and salinity. But while the molecular basis for this protection is still largely unknown, it seems obvious that a common theme in the way GLV work is that most if not all of these stresses are associated with physical damage to the plants, which in turn is the major event responsible for the production of GLV. Here, I summarize the current state of knowledge on GLV and abiotic stresses and provide a model that explains the multifunctionality of these compounds.

Bacillus species produce different classes of antimicrobial and antioxidant substances: peptides or proteins with different structural composition and molecular mass and a broad range of volatile organic compounds (VOCs), some of which may serve as biomarkers for microorganism identification. The aim of this study is the identification of biologically active compounds synthesized by five Bacillus species using gas chromatography coupled to mass spectrometry (GC–MS). The current study profoundly enhances the knowledge of antibacterial and antioxidant metabolites ensuring the unambiguous identification of VOCs produced by some Bacillus species, which were isolated from vegetable samples of potato, carrot, and tomato. Phylogenetic and biochemical studies were used to identify the bacterial isolates after culturing. Phylogenetic analysis proved that five bacterial isolates BSS12, BSS13, BSS16, BSS21, and BSS25 showed 99% nucleotide sequence similarities with Bacillus safensis AS-08, Bacillus cereus WAB2133, and Bacillus acidiproducens NiuFun, Bacillus toyonesis FORT 102 and Bacillus thuringiensis F3, respectively. The crude extract was prepared from bacterial isolates to assess the antibiotic resistance potency and the antimicrobial potential against various targeted multidrug-resistant strains, including Candida albicans, Candida krusei, Enterococcus hirae, Escherichia coli, Klebsiella aerogenes, Klebsiella pneumoniae, Staphylococcus aureus, Staphylococcus epidermidis, Streptococcus group B, Streptococcus mutans, Shigella sonnei, Salmonella enteritidis, Serratia marcescens, Pseudomonas aeruginosa, and Proteus vulgaris. GC–MS analysis of bacterial strains found that VOCs from Bacillus species come in a variety of chemical forms, such as ketones, alcohols, terpenoids, alkenes, etc. Overall, 69 volatile organic compounds were identified from five Bacillus species, and all five were found to share different chemical classes of volatile organic components, which have a variety of pharmacological applications. However, 8 antibacterial compounds with different concentrations were commonly found in all five species: acetoin, acetic acid, butanoic acid, 2-methyl-, oxime-, methoxy-phenyl, phenol, 1,2-benzenedicarboxylic acid, bis(2-methylpropyl) ester, nonanoic acid, and hexadecanoic acid, methyl. The biology and physiology of Bacillus can be better understood using these results, which can also be used to create novel biotechnological procedures and applications. Moreover, because of its exceptional ability to synthesize and produce a variety of different antibacterial compounds, Bacillus species can serve as natural and universal carriers for antibiotic compounds in the form of probiotic cultures and strains to fight different pathogens, including mycobacteria.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Waste materials were chosen to cover the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton 134.5 kJ∙(mol∙K)-1 and the lowest for leather 25.2 kJ∙(mol∙K)-1. The DSC analysis showed number of transformations occurred during pyrolysis for each material. For each transformation, normalized energy required for transformation, or released during transformation were determined and then summarized to present energy balance. The study found that only for three waste materials: PET (-220.1 J⸱g-1), leather (-66.9 J⸱g-1), and chicken meat (-130.3 J⸱g-1) energy balance was negative, while the highest positive balance value was found for potato peelings (367.8 J⸱g-1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

In this paper we describe many important aspects connected with lubricants, namely: the most cheapest organic lubricant in the word, how effectively save lubricant between pairs of friction, what kind of rational shapes for the lubricant must be, what it will be connected with wear and tear using the new organic lubricant (for this purpose formulas and curves are shown in computer program MathCad with calculation). Moreover, there is one physical model which helps to catch car exhausted gases. In conclusion, some recommendations will be given to realize them into the practice during the operation for the different mechanisms including ecology.

High-quality and large-size single crystals of lead-free Na0.5Bi0.5TiO3 were grown using the Czo-chralski technique. The crystals had pure perovskite structure with rhombohedral symmetry and were translucent in the visible and near infrared spectral ranges recorded in the interval 350-1050 nm. The energy gaps determined from the X-ray photoelectron spectroscopy (XPS) and optical measurements were approximately 2.92 eV. The current-voltage characteristics, depolarization current, dc (σdc) and ac (σac) electrical conductivity, and Seebeck coefficient of the crystals were investigated. The frequency/temperature-dependent electrical properties were also measured and analyzed through complex impedance spectroscopy. An overlapping reversible insulator-metal transition (resistive switching) on nanoscales, caused by the electric field, was detected. This was the first time that most of these investigations were performed for this material. The following conductivity mechanisms of NBT single crystals were identified: (i) quasi-free electron and hole conduction and hopping-charges mechanism at low temperatures, (ii) small polaron conductivity in the middle temperature range, and (iii) a significant contribution of the oxygen vacancies to conductivity in the high temperature range. The activation energy values determined from the conductivity data, the imaginary part of the electric impedance and the modulus indicate that the relaxation process in the high-temperature range is attributable to both single and double ionized oxygen vacancies, in combination with the hopping of electrons between Ti4+ and Ti3+. P-type electrical conductivity was also found. These discoveries create new possibilities of reducing the electrical conductivity of NBT and improving the process of effectively poling this material. The density of the electronic states was investigated using an ab initio method. The energy gap cal-culated for NBT (R3c) was 2.8 eV, and is well comparable to those determined from XPS and optical measurements. Our results indicate the possibility of tuning material properties by inten-tionally creating non-stoichiometry/structural defects (oxygen vacancies, cation excess and cation deficiency).

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

The broad acceptance of electromobility depends heavily on the performance and service life of the battery technology used. Lithium-ion battery technology is currently the most promising energy storage technology for mobile applications, but the performance and capacity of the cells is extremely temperature sensitive. Especially in these new complex and powerful applications there is a significant need for thermal management. Depending on the ambient conditions, part of the effective battery energy must therefore be used to temper the system. So far, mainly active components have been used for this task. This not only reduces the overall efficiency, but also increases the weight, volume and maintenance requirements of the system. In the present work, an alternative battery temperature management system (BTMS) was developed. A concept based on latent heat storage materials was created, which uses the advantages of thermal energy storage and the design freedom of additive manufacturing technology, and its suitability for use in battery applications was checked. On the one hand, the use of systems for storing thermal energy was researched and, on the other hand, an innovative cooling concept was created considering new production possibilities.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

While traditional AC mechanical circuit breakers have been competent for protecting AC circuits, high penetration of DC power distribution technologies like DC microgrids (MGs) obligate better disruption performance features such as quick and reliable switch-ing speeds. However, a DC circuit breaker (DCCB) novel design is challenging due to the need to quickly break high currents within milliseconds, caused by the high fault current rise in DC grids compared to AC grids. In DC grids, the circuit breaker must provide zero current crossing and be designed for absorbing surges since the arc is not naturally extinguished by the system. Additionally, the DC breaker must mitigate the magnetic energy stored in the system inductance and withstand residual over-voltages after current interruption. These challenges require a fundamentally different topology for DCCBs, which are typically made using solid-state semiconductor technology, metal oxide varistors (MOV), and ultra-fast switches. This study aims to provide a comprehensive review on development, design, and performance description of DCCBs in parallel with a specific concentration on analysis of internal topology, energy absorption path and sub-circuits in Solid-State (SS)-based DCCBs. The research explores various novel designs that introduce different structures for energy dissipation solution. The classification of these designs is based on the fundamental principles of surge mitigation and a detailed analysis of the techniques employed in DCCBs. In addition, our framework offers an advantageous reference point for the future evolution of SS-circuit breakers in numerous developing power delivery systems.

The dynamic behaviour of a machine tool (MT) directly influences the machining performances. The adoption of lightweight structures may reduce the effects of undesired vibrations and increasing the workpiece quality. This paper aims to present and compare a set of hybrid materials that may be excellent candidate to fabricate the MT moving parts. The selected materials have high dynamic characteristics and capacity to damp mechanical vibrations. In this way, starting by the kinematic model of a milling machine that highlights the main critical factors, this study paper evaluates a number of prototypes made of Al Foam sandwiches (AFS), Al Corrugated sandwiches (ACS) and materials reinforced by carbon fibres (CFRP). A set of prototypes has been fabricated, represented the Z-axis ram of a commercial milling machine. The static and dynamical properties have been evaluated by using both FE simulations and experimental tests. The obtained results show that the proposed structures may be a valid alternative to the conventional materials of MT moving parts, increasing machining performances. In particular, the AFS prototype highlighted a damping coefficient that is 20 times greater than a conventional ram (e.g. steel). The CFRP structure is able to satisfy the machining requirements with a reduced weight of 48.5%, while the ACS prototype showed a good trade-off between stiffness and damping.