This study investigates the preparation of KNN-ZnO composites through optimized sintering conditions under both inert and oxygen atmospheres. Initial experiments employing inert hot pressing were hindered by the necessity for annealing, which resulted in cracks due to the differing thermal expansion coefficients of KNN and ZnO, rendering this method unsuitable for composite fabrication. Consequently, sintering under an oxygen atmosphere was adopted, yielding a uniform distribution of ZnO particles within the KNN matrix. The resultant microstructure demonstrated significant densification, enhanced homogeneity, and minimal porosity. Electrical performance evaluations revealed that while the incorporation of ZnO led to a slight reduction in the ferroelectric properties (d₃₃ and polarization) of the KNN matrix, it concurrently improved the electromechanical quality factor (Q_m) by 40%. However, the overall enhancements were less pronounced when compared to analogous BNT-BT systems, underscoring the necessity for further optimization of processing conditions to boost electromechanical efficiency and piezoelectric response in KNN-based ceramics.

In this work, we report the electric energy storage properties of (1-x)Bi0.5(Na0.8K0.2)0.5TiO3-xBi0.2Sr0.7TiO3 (BNKT-BST; x = 0.15-0.50) relaxor ferroelectric ceramics enhanced via a domain engineering method. A rhombohedral–tetragonal phase, the formation of highly dynamic PNRs, and a dense microstructure are confirmed from XRD, Raman vibrational spectra, and microscopic investigations. The relative dielectric permittivity (2664 at 1 kHz) and loss factor (0.058) were gradually improved with BST (x=0.45). The incorporation of BST into BNKT can disturb the long-range ferroelectric order, lowering the dielectric maximum temperature Tm and inducing the formation of highly dynamic polar nano-regions. In addition, the Tm shifts toward high temperature with frequency and a diffuse phase transition, indicating relaxor ferroelectric characteristics of BNKT-BST ceramics, which is confirmed by the modified Curie Weiss law (γ=1.83). The rhombohedral–tetragonal phase, fine grain size, and lowered Tm with relaxor properties synergistically contribute to a high recoverable energy density Wrec of 0.81 J/cm3 and a high energy efficiency η of 86.95% at 90 kV/cm for x = 0.45.

A high-performance Lead-free Piezoelectric Energy Harvester (LPEH) based on a Ba0.85Ca0.15Ti0.90Zr0.10O3 + CuO 0.3 wt% (BCTZC0.3) composite was fabricated by sintering at 1450℃. The BCTZC0.3 composite, which has an enhanced high-energy-conversion constant (〖d_33×g〗_33), shows improved piezoelectric power-generation performance when compared with conventional piezoelectric energy harvesters. The BCTZC0.3-based LPEH produces instantaneous maximum power of 8.2 mW and an energy density of 107.9 mW/cm3 in a weak magnetic field of 250 μT. This energy harvester can be used to charge a capacitor and operate a wireless sensor network (WSN) system to provide temperature sensing and radio-frequency (RF) transmission in a 250 μT magnetic field. The proposed LPEH is a promising green-energy device for potentially self-powering WSN systems when applied.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

Lead halide perovskite has become a promising candidate for high-performance photodetector (PD) applications due to its attractive optical and electrical properties such as high optical absorption coefficient, high carrier mobility, and long carrier diffusion length. However, the presence of highly toxic lead in these devices has limited their practical applications and even hindered their progress toward commercialization. Therefore, the scientific community has been committed to searching for low-toxic and stable perovskite-type alternative materials. Lead-free double perovskite materials, which are still in the preliminary stage of exploration, have achieved inspiring results in recent years. In this review, we mainly focused on two types of lead-free double perovskite based on different Pb substitution strategies, including A2M(I)M(Ⅲ)X6 and A2M(IV)X6. We reviewed the research progress and prospects of lead-free double perovskite photodetectors in the past three years. And more importantly, from the perspective of optimizing inherent defects in materials and improving device performance, we proposed some feasible pathways and made an encouraging perspective for the future development of lead-free double perovskite photodetectors.

This paper presents a demonstration of the feasibility of fabricating micro-cantilever harvesters with extended stress distribution and enhanced bandwidth by exploiting an M-shaped two-degrees-of-freedom design. The measured mechanical response of the fabricated device displays the predicted dual resonance peak behavior with the fundamental peak at the intended frequency. This design has the features of high energy conversion efficiency in a miniaturized environment where the available vibrational energy varies in frequency. It makes such a design suitable for future large volume production of integrated self powered sensors nodes for the Internet-of-Things.

This work shows a correlation between light reflectance, absorption, and morphologies of series of (1-x) BM–x PT, (x = 0.0, 0.02, 0.04, 0.08, 0.12, 0.16, 0.24) ceramics composite. The (1-x) BM–x PT showed features of a black mirror with a low optical energy gap. The measured Vis-NIR diffused reflectance enabled the calculation of the energy gap using the modified Kubelka-Munk function. The estimated energy gap was lower than 1.5 eV related to low reflectance in the Vis-NIR range. Moreover, obtained histograms of grains, using scanning electron microscope, enabled the correlation between grains size and amount of lead titanate. We deduced from the ceramics surface morphology that marked porosity also induced reflectivity of low magnitude. We correlated the magnitude of the energy gap with phases of the BM-PT composite and with the electrical conductivity activation energy reported in the literature. Our results findings opened prospect studied materials for optical applications.

Considering that the electric refrigeration temperature range of 0.94BNT-0.06BT ceramic materials is 100~140˚C, the electric refrigeration performance of the 0.94BNT-0.06BT ceramic material system was modified by LiNbO3 doping to reduce the cooling temperature. As a result, the refrigeration temperature range of the 0.94BNT-0.06BT ceramic material system was lowered to 25~80 ˚C, achieving its cooling effect near room temperature, and in this temperature range, the adiabatic temperature changes ∆T>0.6K.

The stability issues in the widely known organic inorganic halide perovskite, CH3NH3PbI3, lead to the development of alternative halide double perovskite materials which get great attention in recent times. Although the stability issue seems promising, both materials and device performance of these photovoltaic materials remain inferior and challenging for improvements. Furthermore, the power conversion efficiency of single junction organic inorganic halide perovskite is now 24.2% and 29.15% for textured monolithic perovskite/silicon tandem solar cell, but for all-inorganic halide perovskite solar cell is 7.11% and halide double perovskite solar cells based on Cs2AgBiBr6 and Cs2TiBr6 is 2.8% and 3.3%, respectively, which is far less than 24.2% and 29.15%, respectively. This creates big question and concern that can both all-inorganic halide perovskite solar cell and halide double perovskites solar cells really be an acceptable alternatives to replace organic inorganic halide perovskite solar cells or lead based perovskite solar cells in the market in order to realize the practical applications? Not only this concern, but also there are many other big challenges facing by halide double perovskite solar cells. Such big challenges include: a) geometric constraints and limited integration with interfacial materials, b) dynamic disorder and a wide bandgap and localized conduction band caused by cubic unit cell which restrains the interactions of orbitals, c) high processing temperature which may limit on the diverse applications, d) low electronic dimensionality making them less appropriate for single junction solar cell purpose and etc. Moreover, origin of electronic and optical properties such as the polarizability, the presence of molecular dipoles and their influence on the dynamics of the photo-excitations in the halide double perovskites remains unlock concern that need to be elucidated. Now, another big question is how to develop overcoming mechanisms for such challenges. Can we really overcome these current limitations faced by halide double perovskites so that we use them for commercialization? This research roadmap for performance improvement is suggested focusing on: materials surface and bulk engineering, bandgap engineering, interfacial engineering, composition engineering, doping engineering, device architectural engineering, polar and domain order engineering. This was the reason that this review was developed in order to forward great contributions to the readers and commercial ventures.

Compared to tin lead alloys, lead-free tin alloys have lower toxicity, making them more widely used. In this study, Sn-20Bi-0.3Al-xY solders alloys were prepared. The effects of the addition of Y on its microstructure, micro-hardness, wettability and mechanical properties was investigated. The result showed that the addition of Y had significant effect on the refinement of Sn-20Bi-0.3Al-xY. From the spreading tests results, Y increased the wettability of the solders, however when the fraction of Y gradually increased, the wettability reduced. The ultimate tensile and hardness of Sn-20Bi-0.3Al-xY solders alloys were increased as the content of Y increasing.

Lead pollutants mainly from urban agricultural practices, Leaded paints, Leaded fuels spillages, Lead-contaminated air, soils, and water sources pause a health threat to urban children in Uganda. Prolonged Lead exposure affects iron metabolism, by competitively blocking iron absorption leading to anemia. Blood Lead (BL) inhibits key enzymes ferrochelatase and aminolevulinic acid dehydrogenase (ALAD) involved in hemoglobin (Hb) biosynthesis even at very low levels. Lead poisoning and malaria infection geographically overlap, and both produce similar hematological outcome especially in children. Malaria parasites cause anemia by destroying parasitized red blood cells, therefore, co-existence of BL and malaria parasites infection worsens the anemia status of the host. This study aimed at expounding the extent of heme synthesis inhibition by BL levels among a study group of malaria positive children by measuring levels of free erythrocyte protoporphyrin (FEP) in blood samples. Briefly venous blood samples from 198 children were analyzed for malaria parasite densities by the thick smear method, hemoglobin (Hb) concentrations determined by the standard cyan methemoglobin method, BLL were analyzed on an atomic absorption spectrophotometer and FEP levels were fluorometrically measured. The results showed means of BLL (9.3 µg/dL), Hb (7.5 g/dL), FEP/Hb (8.3 µg/g) and parasite density (PD) (3.21×10³ parasites / µL) among the study group. A majority of 151/198 (76.3%) of the children were moderately anemic while 8/198 (4%) were severely anemic. There was weak correlation between PD and Hb (R²= -0.15, P-value < 0.001), as compared to one between FEP/Hb and Hb (R²= -0.6, P-value=0.001). The study concludes that BL is a significant contributor to malaria anemia and should be considered in the management of anemia in malaria-endemic areas.

Research on the lead halide-based perovskite solar cells have obtained considerable interest in photovoltaic industry owing to their higher efficiency, easy manufacturing, light-weight and low cost. However, these lead halide-based solar cells are not suitable to manufacture commercially because of the toxicity of lead-based materials. In this context, a lead-free perovskite, cesium-bismuth iodide (Cs₃Bi₂I₉) is considered as a potential alternative to the lead halide-based cell due to their non-toxicity and stability, but this perovskite cannot be matched with random hole transport layer (HTL) and electron transport layer (ETL) materials compared to lead halide-based perovskite because of their crystal structure and band gap. Therefore, in this study, performance comparison of different ideal HTL and ETL materials for Cs₃Bi₂I₉ perovskite layer were studied using SCAPS-1D device simulation on the basis of open circuit voltage, short circuit current, power conversion efficiency (PCE) and fill factor (FF) as well as several novel PSC configuration model were designed that can direct for further experimental research for PSC device commercialization. Results from this investigation reveals that the maximum efficiency of 20.96% is obtained for the configuration ITO/WS₂/Cs₃Bi₂I_9­/NiO/Au with optimized parameters such as thickness 400 nm, band gap 2.1eV, absorber layer defect density 10¹² cm^-3, donor density of ETL 10¹⁸ cm^-3 and the acceptor density of HTL 10²⁰ cm^-3.

Heterojunctions based on metal halide perovskites (MHPs) are promising systems for photocatalytic hydrogen evolution reaction (HER). In this work, we coupled Cs3Bi2Br9 nanocrystals (NCs), obtained by wet ball milling synthesis, with g-C3N4 nanosheets (NSs) produced by thermal oxidation of bulk g-C3N4 in air. These methods are reproducible, inexpensive, and easy to scale up. Heterojunctions with different loadings of Cs3Bi2Br9 NCs were fully characterized and tested for HER. A relevant improvement of H2 production with respect to pristine carbon nitride was achieved at low NCs levels reaching values up to about 4600 µmol g-1 h-1. This work aims to provide insights on the synthesis of inexpensive and high performing heterojunctions using MHP for photocatalytic applications.

In this article, a technology for producing wire and rod solder from 52In-48Sn alloy has been developed and investigated in the conditions of small-scale production. The use of direct extrusion of wire and rods instead of the traditional technology for producing solder, which includes pressing, rolling and drawing, can significantly reduce the fleet of required equipment. Using only a melting furnace and a hydraulic press, solder wires and rods can be produced in various sizes. Shortening the production cycle allows you to quickly fulfill small orders and be competitive in sales. The article developed a mathematical model of direct extrusion, which allows you to calculate: extrusion ratio, extrusion speed and pressing force. The results of modeling the process of extrusion of wire ∅2.00 mm and rods ∅8.0 mm made of 52In-48Sn alloy are presented. The temperature of the solder and the tool is simulation in software QForm based on the finite element method. Experimental results of manufacturing ∅2.0 mm solder wire and ∅8.0 mm rods are presented. The microstructure of the direct extruded solder is a eutectic of phases γ and β. Energy-dispersive X-ray spectroscopy (EDS) mapping of the 52In-48Sn alloy showed that the solder obtained by direct extrusion has a uniform distribution of structural phases. The developed technology can be used in the manufacture of wires and rods from other low-melting alloys.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

Most methods for measuring environmental lead (Pb) content are time consuming, expensive, hazardous, and restricted to specific analytical systems. To provide a facile, safe tool to detect Pb, we created pMet-lead, a portable fluorescence resonance energy transfer (FRET)-based Pb biosensor. pMet-lead comprises a 3D-printed frame housing a 405-nm laser diode — an excitation source for fluorescence emission images (YFP and CFP) — accompanied by optical filters, a customized sample holder with a Met-lead 1.44 M1 (the most recent version)-embedded biochip, and an optical lens aligned for smartphone compatibility. Measuring the emission ratios (Y/C) of the FRET component enables Pb detection with a dynamic range of nearly 2 (1.96), pMet-lead/Pb dissociation constant (K_d) 45.62 nM, and limit of detection 40 nM (0.832 μg/dL, 8.32 ppb). To mitigate earlier problems with lack of selectivity for Pb vs. zinc, we preincubated samples with tricine, a low-affinity zinc chelator. We validated pMet-lead measurements of characterized laboratory samples and unknown samples from six regions in Taiwan by inductively coupled plasma mass spectrometry (ICP-MS). Notably, two unknowns had Y/C ratios significantly higher than that of the control (3.48 ± 0.08 and 3.74 ± 0.12 vs. 2.79 ± 0.02), along with Pb concentrations (10.6 ppb and 15.24 ppb) above the WHO-permitted level of 10 ppb in tap water, while the rest four unknowns showing no detectable Pb upon ICP-MS. These results demonstrate that pMet-lead provides a rapid, sensitive means for on-site Pb detection in water from the environment and in living/drinking supply systems to prevent potential Pb poisoning.

One-Dimensional Solar Cell Capacitance Simulator (1D-SCAPS) and n-i-p planar configuration have been employed for the simulation of the caesium tin iodide (CsSnI₃)-based perovskite solar cell (PSC) with titanium (IV) oxide (TiO₂) and copper thiocyanate (CuSCN) as the electron and hole transport materials respectively. The results obtained for the initially modeled PSC compared well with similar devices in the literature but marred with high recombination rate. As such, the defect density in the CsSnI₃ absorber was varied from 10¹³ cm^-3 to 10¹⁷ cm^-3 and enriched with SnCl₂ (additive) and Br⁻(dopant) respectively. This strategy ensured a reduced concentration of Sn⁴⁺ vacancy (V_Sn) in the CsSnI₃ absorber with improved carrier lifetime and diffusion length beyond 0.05 ns and 1.1µm by a magnitude of the order of 10³ and 10² respectively for the enriched CsSnI₃ –based PSC. For the optimized PSC, we recorded V_OC=1.289 V, J_SC=32.60 mA.cm^-2, FF=83.56% and PCE=35.12%.

For the eutectic molten PbBi alloy, we tested the additive properties of density, sound velocity, compressibility and dynamic viscosity of this alloy in the temperature range 600 – 1200 K. All these values can be represented as a mass-weighted sum of the corresponding values of pure lead and bismuth in the temperature range 600 – 1000 K within the limit of experimental errors. In the temperature range 800 – 900 K, we found that interatomic forces in the eutectic increase with temperature, which is caused by a decrease in the size of accumulations of atoms, clusters, of melt. A decrease in the size of clusters is accompanied by an increase in bonds between atoms within the clusters, which make them more stable.

Objective: To determine blood lead levels (BLL) in a healthy paediatric population and to analyse related sociodemographic, dietary and haematological factors. Methods: A cross-sectional study was made of 1,427 healthy subjects aged 1-16 years from the city of Almería (south-eastern Spain). BLL, iron parameters and erythropoietin were determined, and sociodemographic and dietary data obtained. The study data were analysed by multiple logistic regression. Results: The mean BLL was 1.98±1.1 µg/dl (95% CI:1.91–2.04). For 5.7% of the population, mean BLL was 2-5 µg/dl, for 2.1% it was >5 µg/dl and for 0.15% it was >10 µg/dl. Multivariate analysis showed that immigrant origin (OR:11.9; p<0.0001), low level of parental education (OR:4.6; p<0.02) and low dietary iron bioavailability (OR: 3.2; p<0.02) were all risk factors for toxic BLL. Subjects with toxic and non-toxic BLL presented similar iron and erythropoiesis-related parameters, except erythrocyte protoporphyrin, which was significantly higher in the BLL >5 µg/dl group. Conclusions: BLL and the prevalence of toxic BLL in healthy subjects aged 1-16 years living in south-eastern Spain are low and similar to those found in other developed countries. The factors associated with toxic BLL are immigrant origin, low level of parental education and dietary iron deficiency. The toxicity of BLL was not related to changes in the analytical parameters studied.

Flushing tap water is often promoted as a simple and low cost approach to reducing water lead exposures. This study evaluated lead reduction when prevailing flush guidelines (30 seconds-2 minutes) are implemented in a city compliant with lead-associated water regulations (New Orleans, LA). Water samples (n=1,497) collected from a convenience sample of 376 residential sites (2015-2017) were analyzed for lead in samples collected: at 1) first draw (n=375), and after incremental flushes of 2) 30-45 seconds (n=375), 3) 2.5-3 minutes (n=373), and 4) 5.5-6 minutes (n=218). There was no significant reduction when compared to the first draw lead level, until the 6 minute flush (p<0.05); but most sites (52%) still had detectable lead (≥1 ppb) after 6 minutes. Older homes (pre-1950) and low occupancy sites had significantly higher WLLs (p<0.05).Each sample type had health-based standard exceedances at over 50% of sites sampled (max: 58 ppb). While flushing is an effective short-term approach to remediate high lead, prevailing flush recommendations are an inconsistently effective exposure prevention measure that can often inadvertently increase exposures. Public health messages should be modified to ensure appropriate application of flushing for specific cities, while acknowledging its short-comings and practical limitations.

The research was conducted in the Kırklareli stream, which flows southwest through the city of the same name toward the village of Kavaklı. The aim of the study is to evaluate water analysis results and assess the potential that the European Union drinking water standard for lead can be achieved in the Kırklareli stream by reliance on the low solubility of lead phosphate minerals. The present study used Visual MINTEQ 3.1 for all water chemistry simulations. The European Union drinking water standard for lead, which is 10 μg L⁻¹, is exceeded at least once and as many as three times at seven of the ten sites during the 2018 sampling season. Although the database solubility of hydroxypyromorphite is exceeded in most samples, it appears this may be the result of major ion substitutions in the hydroxypromorphite that forms in the Kırklareli stream which increases the effective solubility of lead in the stream.

: The objective of this work is to elucidate the role of partnerships and the number of partners necessary for lead user innovation outcomes. Lead user theory identifies these users as being ahead of market trends and experiencing significant benefits from innovating. So far, most lead user research has concentrated on firms and not individual lead users’ perspective. Data were obtained using a quantitative design during which 321 respondents participated. The SPSS software was used to analyze the data and determine significance. These findings indicate a connection between number of partners and lead user innovation success. This demonstrates that number of partners is significant in determining the success or failure of an innovation. This study provides empirical evidence that the number of partners is an essential factor that influences the success of innovation, and establishes the absolute numbers for achievement of successful innovation. Future studies must investigate the possible implications of integrating the partner variables with other characteristics of the lead user.

Anthropogenic lead pollution is an environmental problem that threatens the quality of soils and waters and endangers living organisms in numerous surface and subsurface habitats. Lead coprecipitation on mineral surfaces through dissolution-recrystallization processes has long term effects on lead bioavailability. Gypsum and calcite are among the most abundant and reactive rock forming minerals present in numerous geological settings. In this work, we study the interaction of slightly acidic (pHi = 5.5) Pb-bearing aqueous solutions ([Pb]i = 1 mM and 10 mM) with crystals of gypsum and /or calcite under atmospheric conditions. This interaction results in a reduction of the concentration of lead in the liquid phase due to the precipitation of newly formed Pb-bearing solid phases. The extent of this Pb removal mainly depends on the nature of the primary mineral phase involved in the interaction. Thus, when gypsum is the only solid phase initially present in the system the Pb-bearing liquid-gypsum interaction results in Pb removals in the 98-99.8 % range, regardless of [Pb]i. In contrast, when the interaction takes place with calcite, Pb removal strongly depends on [Pb]i. It reaches 99% when [Pb]i = 1 mM while it is much more modest (⁓13%) when [Pb]i = 10 mM. Interestingly, Pb-removal is maximized for both [Pb]i (99.9 % for solutions with [Pb]i = 10 mM and 99.7% for solutions with [Pb]i = 1 mM) when Pb-polluted solutions simultaneously interact with gypsum and calcite crystals. Despite the large Pb removals found in most of the cases studied, the final Pb concentration ([Pb]f) in the liquid phase always is well above the maximum permitted in drinking water (0.1 ppm), with the minimum ([Pb]f = 0.7 ppm) being obtained for solutions with [Pb]i =1 mM after their interaction with mixtures of gypsum and calcite crystals. This result suggests that integrating the use of mixtures of gypsum-calcite crystals might help to develop more efficient strategies for in-situ decontaminating Pb-polluted waters through mineral coprecipitation processes.

The work carried out first-principles calculations within the framework of density functional theory to study the structural stability of the CsSnI₃ compound and the influence of phase transitions on their electronic and optical properties. Using the GGA and SCAN functionals, the relaxed structures of the CsSnI₃ phases were obtained and their geometric characteristics were assessed. Using the Phonopy code based on VASP, calculations of phonon and thermodynamic properties were performed, and the temperatures of phase transitions of CsSnI₃ were determined. The temperature dependences of the thermodynamic parameters α-, β-, γ- and δ-phases of CsSnI₃ were analyzed. The trends in free energy, entropy, enthalpy, heat of formation energy and heat capacity were justified in terms of the pattern of changes in the total energy of the four phases of CsSnI₃ from VASP calculations. It is shown that at 0 K the non-perovskite structure of the CsSnI₃ compound (δ-CsSnI₃) is the most stable (followed by γ-CsSnI₃), and the tetragonal phase (β) is quite unstable, having the highest energy among the perovskite phases. It was revealed that at temperatures above 450 K the tetragonal phase becomes stable, and when the temperature drops, it transforms into the cubic phase (α-CsSnI₃). The phase transition between the β and γ phase of perovskite occurs in the range of 300-320 K, and at 320 K a black-yellow transformation of CsSnI₃ occurs in which the cubic phase (black perovskite) undergoes a phase transition to a non-perovskite conformation (yellow phase). The presence of temperature phase transitions between two orthorhombic phases of CsSnI₃ at 360 K was discovered, although direct transitions of the α⟷γ and γ⟷δ types have not yet been reported in any experiment, except for γ→δ transitions under the influence of moisture. Based on well-relaxed structures (from the SCAN calculations), the band gap widths for four CsSnI₃ phases were calculated and compared with experimental measurements. Electronic properties and Fermi level shifts as a result of phase transformations of CsSnI₃ were assessed using the HSE06 functional and machine learning prediction. The values of the complex dielectric constant and the refractive index of all phases of the CsSnI₃ were determined.

Composite membranes formed by sulfonated poly(ether ether ketone) (SPEEK) with embedded carbon quantum dots (CQDs) were used for detection and removal of heavy metal ions, such as lead and cadmium, from water. SPEEK is responsible for the capture of heavy metals based on the cation exchange mechanism, while CQDs detect their contamination by exhibiting changes in fluorescence. Water-insoluble “red” carbon quantum dots (rCQDs) were synthesized from p-phenylenediamine so that their photoluminescence was shifted from that of the polymer matrix. CQDs and the composites were characterized by several techniques: FTIR, Raman, UV/VIS, photoluminescence, XPS spectroscopies and AFM microscopy. The heavy metal ion concentration was analyzed by inductively coupled plasma–optical emission spectroscopy (ICP-OES). The concentration ranges were 10.8 - 0.1 mM for Pb2+ and 10.0 - 0.27 mM for Cd2+. The composite achieved 100% removal efficiency for lead and cadmium if the concentration was below a half of the ion exchange capacity of SPEEK. The regeneration of membranes in 1 M NaCl was also studied. SPEEK/rCQDs showed a turn-off effect more pronounced for lead. A second order law was effective to describe the kinetics of the process.

Adding zinc (II) and formate anions improves the thermal phase-stability of alpha-FAPbI3 materials and the spin-coated thin films of such doped FAPbI¬3 show an increased emission lifetime of up to 3.7 microsecond on quartz. This work investigates the effects of zinc and formate on the stability and time resolved photoluminescence of FAPbI3 perovskites for solar cell applications. Perovskite samples with varying concentrations of zinc and formate were made by incorporating different amounts of zinc formate and zinc iodide and characterized with XRD. Doping levels of 1.7% Zn(II) and 1.0% formate (relative to Pb) seem optimal. The thermal stability of the perovskite powders and thin films were assessed. XRD was virtually unchanged after 6 months. The time-resolved photo-luminescence spectroscopy of the doped spin-coated perovskite samples is reported. The results show that synergy between an anionic and a cationic dopant can take place, making the perovskite thermally more stable with a longer charge carrier lifetime.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

There has recently been interest in the development of small-molecule inhibitors of the oligomerization of Bacillus anthracis protective antigen for therapeutic use. Some of the proposed lead compounds have, however, unfavorable solubility in aqueous medium, which prevents their clinical use. In this computational work, we have designed several hundreds of derivatives with progressively higher hydrosolubility and tested their ability to dock the relevant binding cavity. The highest-ranking docking hits were then subjected to 125 ns-long simulations to ascertain the stability of the binding modes. Several of the potential candidates performed quite disappointingly , but two molecules showed very stable binding modes throughout the complete simulations. Besides the identification of these two promising leads, these molecular dynamics simulations allowed the discovery of several insights that shall prove useful in the further improvement of these candidate towards higher potency and stability.

The BIOTON® biochar, produced by a wood biomass pyrolysis process, usually applied as a soil amendment, was investigated for a novel application, i.e. the adsorption of lead from contaminated solutions. The experimental activity firstly included the physical-chemical characterization of BIOTON®; SEM images were also obtained to highlight its internal structure. The adsorption process was investigated through batch and column experiments. Adsorption kinetics showed a very rapid achievement of the equilibrium conditions, i.e. at 2h and 4h for 50 mg/L and 100 mg/L initial Pb concentration, respectively. Complete removal also occurred within the same time. The Brunauer–Emmett–Teller model better fitted the equilibrium data for both Pb concentrations, whereas the kinetics were best represented by the pseudo second order model. The column tests showed that the addition of biochar as adsorbent media within the bed significantly extended the time of breakthrough and exhaustion, with respect to the column filled with soil only. The adsorption capacities of BIOTON® versus lead solutions was found to be comparable to that reported for commercial adsorbents. Therefore, BIOTON® can be considered a valid option, with the additional benefit to reduce the environmental impact since allows to recover a residue which alternately would need to be disposed of.

Anthropogenic activity like Industrialization has unleashed vast quantities of organic pollutants, including heavy metals. The hazardous heavy metals can cause cancer, neurocognitive defects and wide-ranging health problems. The pollutants resist environmental degradation and can often accumulate in the environment. Microbial degradation of pollutants is a potentially efficient solution for pollution remediation. Amongst the heavy metals, lead contamination resulting from anthropogenic activity have resulted in tragic consequences since the advent of human civilization, even in 21^st century as demonstrated by the Flint water crisis in the US. Bioremediation of lead from the environment could be attempted by various strategies, including mitigation of human activity that causes it in the first place. Microbiome, specifically bacteria, mediated bioremediation can serve as a potent platform for remediating environmental pollution with heavy metals such as lead. Herein we will review the mechanisms and methods of microbial bioremediation of environmental heavy metals with a focus on lead and highlight the challenges and opportunities.

Adopting banana peel as raw material, the adsorption properties of banana peel hydrothermal carbon modified with KOH solution for lead ions in aqueous solution were studied. The surface structure and functional groups of the modified hydrothermal carbon were analyzed by XRD and SEM. The results showed that the banana peel hydrothermal carbon prepared from 0.5 mol/L KOH solution had large pores, and its adsorption capacity reached 42.92 mg/g at a pH value of 6; When the concentration of KOH solution is 0.5 mol/L, the solid liquid ratio is 2 g/L, the adsorption capacity reaches 21.39 mg/g, and the adsorption rate reaches 82.74%; When the concentration of lead solution increased to 100 mg/L, the adsorption capacity of modified hydrothermal carbon for lead ions decreased to 78.26%; The equilibrium adsorption time of lead ion in solution on phosphoric acid modified hydrothermal carbon from banana peel was 250 minutes, and the adsorption process met the quasi second order kinetic model and Freundlich isotherm equation, with an equilibrium adsorption rate of 88.62%. The adsorption of lead ions in solution by KOH modified hydrothermal carbon is mainly chemical physical adsorption.

Using banana peel as raw material, the adsorption properties of hydrothermal carbon pre-10 pared from banana peel modified with different concentrations of phosphoric acid solution for lead 11 ions in aqueous solution were studied. The surface structure and functional groups of the modified 12 hydrothermal carbon were analyzed by XRD and SEM. The results show that the surface of the 13 modified banana peel hydrothermal carbon prepared at 240℃ and 2mol/L phosphoric acid solution 14 has large pores. The adsorption capacity is larger when pH value is 6.When the concentration of 15 phosphoric acid solution was 2mol/L, the solid-liquid ratio was 2g/L, the adsorption capacity was 16 40.64mg/g, and the removal rate was 82.74%.When the initial concentration of lead solution in-17 creased to 100mg/L, the adsorption capacity of modified hydrothermal carbon for lead ion increased 18 to 76.81mg/g, and the removal rate decreased to 76.81%.The equilibrium adsorption time of banana 19 peel phosphoric acid modified hydrothermal carbon for lead ions in solution is 300min. The adsorp-20 tion process satisfies the pseudo-second-order kinetic model and Langmuir isotherm equation. The 21 reaction temperature is 313K, and the equilibrium adsorption capacity can reach 101.19mg/g. The 22 adsorption of Pb ions in aqueous solution by phosphoric acid modified hydrothermal carbon is 23 dominated by single layer chemisorption. The artificial neural network has a fitting correlation of 24 0.99, and the adsorption process includes physical adsorption, electrostatic attraction, ion exchange, 25 and surface complexation.

In this study, fig leaves, zeolite and alginate were used to prepare a biocomposite for the adsorption of Pb(II) ions from aqueous solutions. Effects of various parameters on the biosorption process such as pH, temperature, initial lead concentration and contact time have been investigated. Maximum uptake of Pb(II) ions (85%) has been achieved at pH 6, with 25 mg/L of initial concentration and at a temperature of 288.15 K. Among the applied models, the data correlated well with Freundlich and D-R models and it was established that the biosorption was physical in nature. The amount of adsorbed lead per gram of sorbent was found to be 150.3 mg/g. Thermodynamic parameters showed the exothermic heat of biosorption and the feasibility of the process. Results have suggested that the prepared biosorbent possesses promising biosorption potential.

An ambitious citizen-science effort in the city of Indianapolis (Indiana, USA) led to the collection and analysis of a large number of samples at the property scale, facilitating the analysis of differences in soil metal concentrations as a function of property location (i.e., dripline, yard, and street) and location within the city. This effort indicated that dripline soils had substantially higher values of lead and zinc than other soil locations on a given property, and this pattern was heightened in properties nearer the urban core. Soil lead values typically exceeded the levels deemed safe for children’s play areas in the US (<400 ppm), and almost always exceeded safe gardening guidelines (<200 ppm). As a whole, this study identified locations within properties, and cities, that exhibited the highest exposure risk to children, and also exhibited the power of citizen science to produce data at a spatial scale (i.e., within a property boundary) that is usually impossible to feasibly collect in a typical research study.

The volume of electronic waste (e-waste) received in Nigeria is reportedly on the increase and the effects on environmental health are yet to be fully ascertained. This study aimed to investigate haematological indices, lead and serum iron levels in workers occupationally exposed to electronic wastes in South-South, Nigeria. In this pilot study, 104 participants were enrolled from Benin City, South-South Nigeria; consisting of 63 E-waste Workers (EW) sex- and aged-matched with 41 Unexposed Participants (Control). Blood levels (5 mL) of the metals (lead and iron) were determined using Inductively Coupled Plasma-Mass Spectrometry while the haematological parameters [white blood cells (WBC), Lymphocytes ( LY); monocytes (MO), granulocytes(GR), red blood cells (RBC), haemoglobin (Hgb), haematocrit (HCT), mean cell volume (MCV), mean cell haemoglobin (MCH), mean cell haemoglobin concentration (MCHC) and platelets (PLT)] were determined using standard methods. Results obtained from this study show a significantly low serum iron (11.5 ± 2.14 µg/dL) in the EW compared with Control (168.9 ± 2.39 µg/dL); while blood lead level in EW (1.07±0.02 µg/dL) was significantly elevated compared with Control (0.72 ± 0.12). Total WBC and RBC, HCT, MO and MCV were all significantly elevated in EW compared with Control while LY and PLT in the EW were significantly decreased compared with Control. This study concludes that chronic occupational e-waste exposure may increase blood lead level, lower serum iron status and may have adversely altered some important haematological parameters in the studied population.

We evaluated the association of blood pressure with blood levels of cadmium, lead, and cadmium and lead together (cadmium+lead) in a representative sample of adolescents from Korea by use of 2010-2016 data from the Korean National Health and Nutrition Examination Survey (KNHANES). This cross-sectional study enrolled adolescents aged at 10-18 years-old who completed a health examination survey and had blood measurements of lead and cadmium. The association of adjusted mean differences in diastolic and systolic blood pressure with doubling of blood lead and cadmium were estimated by regression of blood pressure against log₂-transformed blood metals and their quartiles after covariate adjustment. Adjusted odds ratios for prehypertension were calculated for log₂-transformed blood levels of lead and cadmium and their quartiles. Our analysis of adolescents in Korea indicated that blood levels of lead and cadmium were not significantly associated with increased blood pressure or risk of pre-hypertension. However, the cadmium+lead level was associated with pre-hypertension. Previous studies showed that blood levels of lead and cadmium were associated with increased blood pressure and risk of hypertension in adult populations. We found no such effect in Korean adolescents, although the cadmium+lead level was associated with prehypertension. These differences may be because adolescents generally have lower levels of these blood metals or because adolescents only rarely have hypertension.

Recycling solar panels is crucial to mitigating the environmental impact of the growing volume of end-of-life photovoltaic waste and conserving valuable resources, while achieving high purity in recovered materials ensures their effective reuse in the manufacturing of new solar panels, con-tributing to a sustainable and circular economy. This study proposes a two-step leaching process to recover Ag and Al from the silicon fraction of EoL photovoltaics (PVs). In the first stage laboratory scale tests, 99% Al was extracted using 5% HCl at room temperature for 3 hrs. The Al was precip-itated as oxide from the solution. The silicon residue was then leached with 0.5 M HNO3 at 80°C for 2 hrs extracting 99% Ag and producing Si with 99.83% purity. The silver was precipitated to produce metallic Ag with >99.9% purity. Methods to mitigate the effluent solutions were recom-mended and the entire process was presented in a flowsheet.

The phenotypic manifestation of lead toxicity includes cognitive, learning, and memory decline which is associated with neuronal injuries and death and been a major challenge in public health especially in developing countries. Thus, we explore the prophylactic potentials of luteolin in prefrontal Pb intoxication. Thirty-six (36) male Wistar Rats were used for this research and di-vided into six (6) groups of six animals each and were treated orally as follows: Group 1-Normal saline (0.5ml daily for 14 days); Group 2- PbCl3 (50mg/kg of PbCl3 daily for 14 days); Group 3- luteolin (100mg/kg of LUT daily for 14 days); Group 4- luteolin and PbCl3 (50mg/kg PbCl3 and 100mg/kg LUT daily for 14 days); Group 5- PbCl3 then luteolin (50mg/kg of PbCl3 daily for 14 days followed by 100mg/kg of LUT daily for 14 days); Group 6- luteolin then PbCl3 (100mg/kg of LUT daily for 14days followed by 50mg/kg of PbCl3 daily for 14 days). We measured cerebral oxidative redox parameters, G6PDH, IL-6, acetylcholinesterase levels, and total protein profiles using ELISA and biochemical assay kits. We also examined cerebral morphology and the Nissl profile with H&E and toluidine blue staining techniques, as well as astrocytic morphology and synaptic integrity with anti-GFAP and anti-synaptophysin antibodies. As a result of Pb perturba-tion, luteolin treatment inhibits MDA, IL-6, and AChE expression while increasing antioxidant enzyme activities (SOD, GPx) and G6PDH. Furthermore, luteolin has significant prophylactic po-tential against Pb-induced neuronal injuries and modulates astrocyte actions, preserving synap-tic integrity and thus improving cognition, learning, and memory. Taken together, our findings indicate that luteolin may be a promising candidate for managing and treating Pb neural intoxi-cation.

Seawater contamination is a global challenge due to its hazardous effects on marine organisms and human health. Twenty-three surface seawater samples were collected from Al Lith intertidal area along the Saudi Red Sea coast to evaluate the ecological risks and document the potential sources of Cr, Cd, Fe, Zn, and Pb. Contamination factor (CF), contamination degree (Cd), water quality index (WQI), and heavy metal pollution index (HPI), as well as multivariate tools were applied. The averages of HMs (μg/L) had the following order: Zn (6.616) &gt; Pb (0.284) &gt; Cd and Cr (0.268) &gt; Fe (0.197). Results of CF showed moderate contamination of seawater with Cd and low contamination for Cr, Fe, Zn, and Pb. However, 26.09% of the samples showed considerable contamination for Cd. Average Cd values revealed low contamination for HMs, while 17.39% of the samples showed moderate contamination. HPI average values indicated medium pollution for Al Lith seawater, meanwhile 13 samples reported high pollution. The higher HPI values were reported in samples characterized by higher concentration of HMs, particularly Cd and Zn. Correlation matrix and principal component analysis suggested anthropogenic sources for Pb and Zn, mostly from industrial and agricultural effluents, landfilling and domestic wastewaters, apart from their natural sources.

This study presents a novel polyurethane-activated carbon composite (PACC) as an effective and sustainable adsorbent for treating lead-ion-contaminated waters. The PACC was characterized using SEM-EDX, FTIR, BET, XRD, and TGA to evaluate its physicochemical and thermal properties. Furthermore, the PACC was employed in an experimental column adsorption setup to investigate its adsorption performance and to develop a dynamic method suitable for industrial implementation. Parameters such as bed height (50, 100, 150 mm), flow rate (4, 6, 8 mL min-1), pH (2, 4, 6), and initial metal ion concentrations (10, 50, 100 mg L-1) were examined. The experimental data exhibited strong agreement with the Thomas and Yoon-Nelson models (R2 ≥ 0.96), indicating efficient adsorption mechanisms. Remarkably, the depleted adsorbent has the potential for facile regeneration without substantial loss in capacity. The PACC demonstrated excellent adsorption performance for lead ions in aqueous solutions in a fixed-bed column system. Thus, the novel PACC material holds potential for scalable application in industrial settings to address water pollution challenges, especially in regions with uncontrolled effluent discharge.

In principle, modular or integral character of manufacturing lines depends on topological designs of products and determined operation tasks. On the other hand, in specific situations there is an articulated need for modular design in smart manufacturing systems, since modular layouts are a crucial step towards agile production via smart manufacturing. The aim of this paper is to explore how the modular layout relates to manufacturing lead time (MLT) and to operational complexity of smart manufacturing systems. For this purpose, topologically different models of alternative process layouts were simulated and tested, while MLT values were obtained using Tecnomatix Plant Simulation. Obtained positive findings of this research could be useful not only in selection of the most suitable process design from the alternative ones, but especially in deepening knowledge and better understanding of the concept of optimal network modularity.

Studies suggest that elevated postnatal blood lead levels (BLLs) are negatively associated with child growth. This study aimed to investigate associations of childhood BLLs at age one-year and growth outcomes at age six-years (n=661) in a cohort of children in Allada, Benin. The growth outcomes studied are weight-for-age Z-score (WAZ), height-for-age Z-score (HAZ) and BMI-for-age Z-score (BMIZ), head circumference (HC), underweight, stunting, and wasting. Multivariable regression models examined associations between blood lead levels, growth outcomes with adjustment for potential confounders. The geometric mean BLLs was 59.3 μg/L and 82% of children had BLLs &gt;35 μg/L at one year. After adjusting for confounding factors, no association was found between BLLs quartiles and HAZ, WAZ, BMIZ, and height and weight growth velocities. However, boys in the highest quartile had 1.02 cm lower HC (95% CI: [-1.81, -0. 24]) as compared to those in the lowest quartile with a dose-response trend across quartiles (Ptrend =0.02). Furthermore, an increased risk of being stunted was observed in children in the highest quartile of exposure compared to the first (OR: 2.43; 95% CI: [1.11 – 5.33]) with a dose-response trend (Ptrend =0.03). Blood lead was found to be associated with an increased risk of childhood stunting and lower head circumference in a resource-limited setting.

In this paper we investigate some properties of square-free numbers. In particular, we study a function that counts the number of square-free numbers no larger than the given number n. We show that this function has asymptotics consistent with the predictions of the Riemann hypothesis and use this to obtain new and better estimates of the density of square-free numbers. Finally, we present a well-known generalization of the concept of a square-free number to monoids and research on square-free factorizations.

This paper explores the suppression of ideas within academic scholarship by academics, either by self-suppression or because of the efforts of other academics. Legal, moral, and social issues distinguishing freedom of speech, freedom of inquiry, and academic freedom are reviewed. How these freedoms and protections can come into tension is then explored by an analysis of denunciation mobs who exercise their legal free speech rights to call for punishing scholars who express ideas they disapprove of and condemn. When successful, these efforts, which constitute legally protected speech, will suppress certain ideas. Real-world examples over the past five years of academics who have been sanctioned or terminated for scholarship targeted by a denunciation mob are then explored.

This study presents a comprehensive approach to calculating the free energy of hydration of methane using Molecular Dynamics simulations. We employed the Free Energy Perturbation (FEP) method to determine the Gibbs free energy associated with transferring a methane molecule into water. Simulations were conducted in a cubic simulation box containing one methane molecule and 1000 TIP4P water molecules. The forward and backward routes were both analyzed, providing consistent free energy differences, which validates the robustness of our methodology. The Gibbs free energy profiles demonstrated characteristic energy barriers and stabilization points, indicative of the interaction dynamics in the solvation process. The results demonstrate the robustness of the FEP method implemented in LAMMPS, yielding free energy in close agreement with experimental data and previous computational studies. The calculated free energy differences for methane hydration exhibited deviations of 13% and 8% for the forward and backward routes, respectively, compared to experimental values. These findings underscore the accuracy and efficiency of using LAMMPS for free energy calculations, contributing to the broader understanding of solvation thermodynamics. Additionally, radial distribution functions were analyzed to provide insights into the structural arrangement of water molecules around methane, revealing strong interaction between methane's carbon atom and water molecules.

Cell free systems are a widely used research tool in systems and synthetic biology and a promising platform for manufacturing of proteins and chemicals. In the past, cell free biology was primarily used to better understand fundamental biochemical processes. Notably, E. coli cell free extracts were used in the 1960s to decipher the sequencing of the genetic code. Since then, the transcription and translation capabilities of cell free systems have been repeatedly optimized to improve energy efficiency and protein yield. Today, cell free systems, in combination with the rise of synthetic biology, have taken on a new role as a promising technology for just in time manufacturing of therapeutically important biologics and high-value small molecules. They have also been implemented in an industrial scale for the production of antibodies and cytokines. In this review, we discuss the evolution of cell free systems, advancements in cell free protein synthesis, and cell free metabolic engineering, and conclude with discussing the importance and feasibility of mathematical modeling in cell free systems.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

For the first time porous tungsten coatings were obtained by vacuum annealing of coatings consisting of both lead solution in β-W and a mixture of Pb solution in β-W and pure lead. Electron-microscopic studies of the obtained coatings before and after vacuum annealing at 800 оС for 1 hour and 6 hours were carried out. The formation of a new phase of tungsten with an octa-lattice and parameter a = 0.4878±0.0005 nm was recorded.

The Internet of Things (IoT) technology connects the real world and the network world by integrating sensors and internet technology, which has greatly changed people's lifestyles, showing its broad application prospects. However, traditional materials for the sensors and power components used in IoT limit its development to high-precision detection, long-term endurance, and multi-scenario applications. Metal halide perovskite, with the unique advantages such as excellent photoelectric properties, adjustable bandgap, flexibility, and mild process, exhibiting enormous potential to meet the requirements for IoT development. This paper provides a comprehensive review of metal halide perovskites' application in sensors and energy supply modules within IoT systems. Advances on perovskite-based sensors were discussed as to gas, humidity, photoelectric, and optical sensors. The application of indoor photovoltaics based on perovskite in IoT systems were also discussed. At last, the application prospects and challenges of perovskite-based devices in IoT are summarized.

Background: Although the link between environmental lead exposure and several patterns of cardiovascular disease (CVD) has been reported, its association with silent myocardial infarc-tion (SMI) has not been explored. We aimed to assess the association between blood lead levels (BLL) and risk of SMI. Methods: This analysis included 7283 (mean age 56.1±2.52 years, 52.5% women) participants from the Third National Health and Nutrition Examination Survey who were free of clinical CVD. Ascertainment of BLL done using graphite furnace atomic absorption spectrophotometry. SMI defined as ECG evidence of MI without history of MI. Multivariable lo-gistic regression analysis was used to examine the association between SMI and BLL. Results: SMI was detected in 120 participants corresponding to an unweighted prevalence of 1.65%. Par-ticipants with higher levels of BLL had higher prevalence of SMI (0.4%, 0.9%, and 2.4% across BLL tertiles; p-value

Electrochemical Impedance Spectroscopy techniques were applied in this work to 9 lead-acid battery prototypes fabricated industrially, divided on three type/technology packages. Frequency dependent impedance changes were interpreted during successive charge/discharge cycles on two distinct stages: 1) immediately after fabrication; and 2) after a controlled aging procedure to 50% Depth of Discharge, following industrial standards. By investigating their State of Health behaviour vs electrical response, three methods were employed, namely the (Q-Q0) total charge analysis, the decay values of Constant Phase Element in the equivalent Randles circuits, and the resonance frequency of the circuit. A direct correlation has been found for prediction of the best performant batteries in each package, thus allowing a qualitative analysis capable to provide the decay of the battery State of Health. We emphasized which parameters are directly connected with their lifetime performance in both stages, and by consequence, which type/technology battery prototype emphasize the best performance. Based on this methodology, the industrial producers can further establish the quality of the novel batteries in terms of performance vs lifespan, allowing them to validate the novel technological innovations implemented in the current prototypes.

The integration of bioinformatics in drug discovery has revolutionized the field of pharmaceutical research. The use of computational tools and techniques has enabled researchers to analyze vast amounts of data, identify potential drug targets, and design new drugs with greater precision and efficiency. The integration of bioinformatics has also facilitated the development of personalized medicine, where drugs can be tailored to individual patients based on their genetic makeup. However, there are still challenges that need to be addressed, such as the need for more accurate predictive models and the ethical considerations surrounding the use of patient data. Overall, the integration of bioinformatics in drug discovery holds great promise for improving human health and advancing our understanding of disease mechanisms. In this mini-review, we discuss how Bioinformatics plays a crucial role in each step of drug discovery by providing tools and techniques to analyze large amounts of data generated from various sources, as well as the challenges and the opportunities offered by bioinformatics.

Clean water is now very rare due to the increased water pollution causing many diseases. Heavy metals mainly lead from industrial waste i.e. batteries, cable sheaths, machinery manufacturing, shipbuilding, lead oxide and radiation protection is accountable & largely contributed lead in river and canal waters. Presence of lead in water is hazardous to life due to many reasons. It can cause cancer, weakness, anemia, kidneys, high blood pressure and nerve diseases. Inorganic lead is reported to me more dangerous than organic one. Industries including batteries, cable sheaths, machinery manufacturing etc. drains water that has soluble lead ranging from 200 – 500 mg/L. The safe limit of lead in water is about 0.015 mg/L. Pakistan is a country rich in minerals. It has about 3.5 MT of Kaolin (Clay) deposits situated at Nagar Parker region of Sindh, Pakistan. This indigenous material is being used to produce ceramic products and in paper making. Now we use this mineral source to remove lead from water by adsorption. Kaolin clay can be used as an adsorbent due to its unique structure. XRF technique is employed for clay characterization. Resultants will be analyzed by UV – Vis Spectrophotometry.

Lead (Pb) is a non-essential, highly toxic, and persistent element widely recognised as one of the most concerning pollutants, and it is listed in the Priority List of Hazardous Substances. Widespread environmental contamination from Pb is a serious issue for human health and wildlife. The liver, a key compartment for metal detoxification and excretion, is also the organ in which Pb mainly accumulates in fish. Herein, we investigated for the first time the morphological and functional injuries induced in zebrafish (Danio rerio) liver by two very low and environmentally relevant concentrations of Pb (2.5 and 5 μg/L) after 48, 96, and 192 hours of exposure. We showed significant histological alterations in all the exposed samples, also demonstrating that the extent of injuries increased with dose and exposure time. The most common modifications observed were congestion of blood vessels and sinusoids, cytoplasmic vacuolizations, parenchyma dyschromia, and macrophage proliferation. Pb administration also resulted in a significant increase in lipid content and the upregulation of key genes involved in metal detoxification (mtf1) and the defensive response against oxidative stress (sod1 and cat). We showed that even very low doses of Pb can disrupt liver morphology and function.

This field study aimed to assess the base line conditions of a long-term polluted shooting range in Argentina polluted with 428 mg kg-1 lead (Pb), to evaluate the establishment and development of Helianthus petiolaris plants and address the efficacy of the phytomanagement strategy through: i) element accumulation in plant tissues; ii) rhizosphere bacterial diversity changes by Illumina Miseq™ and iii) floral water and essential oil yield, composition and element concentration by GC-MS and ICP. After one life cycle growing in the polluted sites, in the roots of Helianthus petiolaris plants Pb concentration was between 195 and 304 mg kg-1 Pb. Only a limited fraction of the Pb was translocated to the aerial parts. The predominance of the genus Serratia in the rhizosphere of Helianthus petiolaris plants cultivated in the polluted sites and the decrees of the essential oil yield were some effects significantly associated with soil Pb concentration. No detectable Pb concentration was found in the floral water and essential oil obtained. Extractable Pb concentration in the soil reduced between 28-45 % after the harvest.

Emergence of multi drug resistant (MDR) and extensively drug resistant (XDR) Mycobacterium tuberculosis poses a serious threat to TB control as the available treatment options are less effective in these cases. Therefore, new strategies are required for identification of new drugs and drug targets. The M. tuberculosis dihydrodipicolinate synthase is a putative drug target with no potent inhibitor. Here in this study, we have used a comprehensive computational approach to identify small molecule inhibitors and validated them in vitro. As similar structures tend to have similar functions, therefore 3 approaches, namely, (a) known inhibitor-based approach, (b) substrate analogues, (c) product analogues were used for compound screening from various chemical libraries. The fourth approach we have taken is fragment library screening.In vitro studies revealed that β-hydroxypyruvic acid tartronic acid are inhibitors of Mtb-rDapA with maximum inhibition 48% and 51% at 500µM concentrations respectively. We have also observed that β-hydroxypyruvic acid is a time dependent inhibitor of Mtb-rDapA. Further, thermal shift assays showed that β-hydroxypyruvic acid interacts with Mtb-rDapA and the thermal stability of Mtb-rDapA shifted by 3˚C. Among the product analogues of Mtb-DapA, dipicolinic acid showed to bind to Mtb-rDapB shifting thermal stability of Mtb-rDapB by 0.5˚C in binding. Additionally, we have designed a new approach by combining substrate and product analogues to achieve better inhibitions. In vitro assays validated that this combination approach increased maximum inhibition up to 100%. We envision that these compounds would serve as potent leads for tuberculosis drug discovery.

Environmental lead exposure is a population health concern in many low- and middle-income countries. Lead is found throughout Myanmar and prior to the 1940s, the country was the largest producer of lead worldwide. The aim of this study was to examine any potential association between lead mining and adult literacy rates at the level of the 330 townships in Myanmar. Townships were identified as lead or non-lead mining areas and 2015 census data were examined with association being identified using descriptive, analytical and spatial statistical methods. Overall, there does appear to be a significant relationship between lead mining activity and adult literacy levels (P<0.05) among townships with both low access [OR= 2.701 (1.136-6.421)] as well as townships with high access to safe sanitation [OR=18.40 (1.794-188.745)]. LISA cluster maps confirm these findings. This exploratory analysis is a first step in the examination of potential environmental lead exposure and its implications in Myanmar.

The accumulation of high levels of lead or lead ions in a human body is harmful, particularly to children. Its neurotoxic effect is profound, damaging the central and peripheral nervous systems, resulting in stunted growth, behavioral problems and learning disabilities. The major source of lead or lead ions comes from the drinking water and tap water. The assessment of the water quality, including lead or lead ion content, is usually completed by a regional water department professional. This assessment is time-consuming and requires expensive instruments and skilled operators. Therefore, there is a need to produce a simple-use and relatively inexpensive method to detect lead or lead ions in water samples. This research has developed a simple-use, cost effective sensor system for the detection of lead ions in tap water. An under-potential deposited bismuth sub-layer on a thin gold film based electrochemical sensor was designed, manufactured and evaluated. Differential pulse voltammetry (DPV) measurement technique was employed in this detection. Tap water from the Cleveland, Ohio, USA regional water district was the test medium. Concentrations of lead ion in the range of 8 X 10^-8 M to 8 x 10^-4 M were evaluated. This DPV detection system required 3 -6 minutes to complete the detection measurement. A longer measurement time of 6 minutes was used for the lower lead ion concentration. The selectivity of this lead ion sensor was very good, and Fe III, Cu II, Ni II and Mg II at a concentration level of 5×10^-4 M did not interfere with the lead ion measurement.

Alzheimer’s disease is the most common neurodegenerative disease and affects persons of all races, ethnic groups, and sexes. The disease is characterized by neuronal loss leading to cognitive decline and memory loss. There is no cure and the effectiveness of existing treatments is limited and depends on the time of diagnosis. The long prodromal period, during which patients’ ability to live a normal life is not affected despite neuronal loss, often leads to a delayed diagnosis because it can be mistaken for normal aging of the brain. In order to make a substantial impact on AD patients, early diagnosis may provide a greater therapeutic window for future therapies to slow AD-associated neurodegeneration. Current gold standards for disease detection include magnetic resonance imaging and positron emission tomography scans, which visualize amyloid β and phosphorylated tau depositions and aggregates. Liquid biopsies, already an active field of research in precision oncology, are hypothesized to provide early disease detection through minimally or non-invasive sample collection techniques. Liquid biopsies in Alzheimer’s disease have been studied in cerebrospinal fluid, blood, ocular, oral, and olfactory fluids. However, most of the focus has been on blood and cerebrospinal fluid due to biomarker specificity and sensitivity attributed to the effects of the blood-brain barrier and inter-laboratory variation during sample collection. Many studies have identified amyloid β and phosphorylated tau levels as putative biomarkers, however, advances in next-generation sequencing-based liquid biopsy methods have led to significant interest in identifying nucleic acids species associated with Alzheimer’s disease from liquid tissues. Differences in cell-free RNAs and DNAs have been described as potential biomarkers for AD and hold the potential to affect disease diagnosis, treatment, and future research avenues.

It is known that exposure to heavy metals such as lead (Pb) and cadmium (Cd) has several adverse effects, particularly on the human reproductive system. Pb and Cd have been associated with infertility in both men and women. In pregnant women, they have been associated with spontaneous abortion, preterm birth, and impairment of the development of the fetus. Since these heavy metals come from both natural and anthropogenic activities and their harmful effects have been observed even at levels of exposure, their exposure remains a public health issue, especially for the reproductive system. Given this, the present study aimed to investigate the potential reproductive effects of Pb and Cd levels in the follicular fluid (FF) of infertile women and no-smokers exposed to heavy metals for professional reasons or living in rural areas near landfills and waste disposal areas, to correlate the intrafollicular presence of these metals with possible alterations in the ultrastructure of human cumulus-oocyte complexes (COCs), probably responsible of infertility. Blood and FF metals were measured using atomic absorption spectrometry. COCs corresponding to each FF analyzed were subjected to ultrastructural analyses by transmission electron microscopy. We demonstrated for the first time that intrafollicular levels of Pb (0.66 µg/dL to 0.85 µg/dL) and Cd (0.26 µg/L - 0.41 µg/L) could be associated with morphological alterations of both the oocyte and CCs ultrastructure. Since blood Cd levels (0.54 µg/L - 1.87 µg/L) were above the current reference values established by the guidelines of the Agency for Toxic Substances and Disease Registry (ATSDR) and the Environmental Protection Agency (EPA), whereas blood Pb levels (1.28 µg/dL - 3.98 µg/dL) were below the ATSDR reference values we believe that these alterations could be due especially to Cd, even if we cannot exclude a possible additional effect of Pb. Our results highlighted that oocytes were affected in maturation and quality, whereas CCs showed scarcely active steroidogenic elements. Regressing CCs, with cytoplasmic alterations, were also numerous. According to Cd's endocrine-disrupting activity, the poor steroidogenic activity of CCs might correlate with delayed oocyte cytoplasmic maturation. So, we conclude that levels of heavy metals in the blood and the FF might negatively affect fertilization, embryo development, and pregnancy, compromising oocyte competence to fertilization both directly and indirectly, impairing CC steroidogenic activity, and inducing CC apoptosis.

Autism Spectrum Disorder (ASD), a neurodevelopmental disorder characterized by persistent deficits in social interaction and communication manifests in early childhood and is followed by restricted and stereotyped behaviors, interests or activities in adolescence and adulthood (DSM-V). Although genetics and environmental factors have been implicated, the exact causes of ASD have yet to be fully characterized. New evidence suggests that dysbiosis or perturbation in gut microbiota (GM) and exposure to lead (Pb) may play important roles in ASD etiology. Pb is a toxic heavy metal that has been linked to a wide range of negative health outcomes including anemia, encephalopathy, gastroenteric diseases and more importantly cognitive and behavioral problems inherent to ASD. Pb exposure can disrupt GM, which is essential for maintaining overall health. GM, consisting of trillions of microorganisms, has been shown to play a crucial role in the development of various physiological and psychological functions. GM interacts with the brain in a bidirectional manner referred to as “Gut-Brain Axis (GBA).” In this review, following a general overview of ASD and GM, the interaction of Pb with GM in the context of ASD is emphasized. Potential exploitation of this interaction for therapeutic purposes is also touched upon.

Four naturally occurring zeolites AZLB-Ca and AZLB-Na (Bowie, Arizona), NM-Ca (Winston, New Mexico), and NV-Na (Ash Meadows, Nevada) were studied to evaluate structural modifications after treatment with HCl acid. AZLB-Ca and AZLB-Na are chabazite-like species and become amorphous when boiled in concentrated HCl acid as confirmed by powder X-ray diffraction. In contrast, NM-Ca and NV-Na which are clinoptilolite-like species withstood boiling in concentrated HCl acid. This treatment removes calcium, magnesium, sodium, potassium, aluminum, and iron atoms or ions from the framework while leaving the silicon framework intact as confirmed via X-ray fluorescence and diffraction. SEM images on calcined and HCl treated NV-Na were obtained. BET surface area analysis confirmed an increase in surface area for the two zeolites after treatment, NM-Ca (20.0(1) to 111(4) m2/g) and NV-Na (19.0(4) to 158(7) m2/g). 29Si and 27Al MAS NMR were performed on the natural and treated NV-Na zeolite and the data for the natural NV-Na zeolite suggested a Si:Al ratio of 4.33 similar to that determined by X-Ray fluorescence of 4.55. Removal of lead ions from solution decreased from the native (NM-Ca, 0.27(14), NV-Na, 1.50(17) meq/g) compared to the modified zeolites (30 min HCl treated NM-Ca 0.06(9) and NV-Na, 0.41(23) meq/g) and also decreased upon K+ ion pretreatment in the HCl modified zeolites.

Understanding the strength of the associations between perceived risk and individuals’ behavioral intentions to protect their health is important for determining appropriate risk communication strategies in communities impacted by lead contamination. We conducted a survey within communities of northern Idaho, USA (n = 306) near a Superfund megasite with legacy mining contamination. We empirically test a theoretical model based on the Health Belief Model. Survey respondents had higher intentions to practice health protective behaviors when they perceived the risk of lead contamination as severe, recognized the benefits of health protective behaviors, and considered the risks of lead contamination. Women reported higher behavioral intentions than men, but age and mining affiliation did not have an association. Survey comments indicated that perceptions about the long-term environmental remediation in the region influenced risk perceptions. Understanding risk perceptions, behavioral intentions, and related factors can aid public health agencies in tailoring risk communication for increasing protective behaviors in mining-impacted communities internationally.

In this paper, the effect of Bi₂O₃ doping on the mechanical properties of PbO ceramic pellets was studied. For this purpose, different ratios of Bi2O3/PbO (i.e., xBi2O3–(1-x)PbO, where x is 0, 1, 3, 5, 7 wt%) were fabricated and sintered at 570, 620, and 670°C. Mechanical properties including density, hardness, flexural strength, and sintering of PbO were studied for the aforementioned compositions. Phase compositions, microstructures, and worn surfaces of the composites were characterized by scanning electron microscopy and X-ray diffraction (XRD). The XRD analysis revealed that a solid solution formed in the composite ceramic. The best suited conditions of temperature and doping of Bi₂O₃ for optimal sintering are 620°C and 3 wt%, respectively. The hardness of the 3 wt% Bi2O3–97 wt% PbO ceramic was 717 MPa, which is about four times higher than the hardness of pure PbO; in addition, the strength of the composites was 43 MPa, which is two times higher than that of pure PbO. The integrity of the composites was verified using the lead–bismuth eutectic alloy flushing experiment. Results of this research paper are important for future studies of oxygen control in the lead–bismuth eutectic alloy of lead-cooled fast reactors.

Direct-to-blister copper flash smelting slag contains up to 14% of copper and 2-4% of lead. Considering this fact, this material is subjected to the high-temperature reduction process. After this, converting process is performed on the Cu-Pb-Fe alloy being the product of decopperization process in electric furnace. An alternative to the presently used processing of flash smelting slag would be its hydrometallurgical treatment and selective recovery of Pb and Cu. This paper presents the results of laboratory tests on flash smelting slag leaching with citric acid solutions. The experiments performed allowed to determine the process parameters at which the Pb concentration in the post-leaching sediment reached the value of 0.41-0.6% while the Pb content in flash smelting slag was 3.05%. Analogous values for copper were 11.5-11.8% (after leaching) and 12.44% (before). Material after leaching in citric acid solutions can be processed, in the second step, using sulfuric acid solutions, and it could lead to the recovery of almost all copper contained in it.

Lead Acid Batteries (LABs) are used for starting, lighting, and igniting, as well as in air conditioning systems and to supply power to electric engines in transport vehicles (TVs). However, the application of LABs for TVs has faced a number of market challenges, mounted by the upcoming high energy density and long lifespan batteries, such as lithium ion. LABs, on the other hand, are inexpensive. The key research question is, how can the lifespan of LABs used in automotive industries be increased, while still ensuring a low cost solution? Thus, integrating LABs with the supercapacitor (known as an electric double layer capacitor—EDLC) is likely to outperform the competing alternative batteries for TVs. This paper proposes a multiple stage approach to hybrid lead acid batteries and a supercapacitor system for TVs that is capable of maintaining the battery state-of-charge (SOC) at statistically high limits, ranging between 90% and 95%. This SOC target will likely ensure that the lifespan of the hybrid battery system can be elongated (extended) more than its competitors. In this study, the multiple stage approach of concatenated converters has been designed in order to satisfy all energy storage requirements for different characteristics of LABs and the supercapacitor. The designed hybrid system has been simulated using Matrix Laboratory (MATLAB/Simulink (version R2016a, MathWorks, Natick, MA, USA)). The simulated results show that high transient currents from the direct current (DC) bus of LABs, caused by the regenerative braking or deceleration of the TVs, reduce the battery lifespan and induce mechanical stress. The supercapacitor reduces the stress on the LAB by absorbing high transient currents. This, in turn, keeps the LABs’ SOC between 90% and 96% and the voltage at 12 V. As indicated by the simulated results, the hybrid battery SOC is maintained at 90–96% and the terminal voltage is approximately 12 V.

Accurate and efficient battery modeling is essential to maximize the performance of isolated energy systems and to extend battery lifetime. This paper proposes a battery model that represents the charging and discharging process of a lead-acid battery bank. This model is validated over real measures taken from a battery bank installed in a research center placed at “El Chocó”, Colombia. In order to fit the model, three optimization algorithms (Particle Swarm Optimization, Cuckoo Search, and Particle Swarm Optimization+Perturbation) are implemented and compared, being the last one a new proposal. This research shows that the model with the proposed algorithm is able to estimate and manage the real battery characteristics as SOC and charging/discharging voltage. The comparison between simulations and real measures shows that the model is able to absorb reading problems, signal delays, and scaling errors. The approach we present can be implemented in other types of batteries especially those used in stand-alone systems.

Milling and mining metal ores are major sources of heavy metal contamination. The Spring River and its tributaries in southeast Kansas are contaminated with Pb, Zn, and Cd as a result of 120 years of mining activities. Trace metal transformations and cycling in mine waste materials greatly influence their mobility and toxicity and affect plant productivity and human health. It has been hypothesized that under reduced conditions in sulfate-rich environments, these metals can be transformed into their sulfide forms, thus limiting mobility and toxicity. We studied biogeochemical transformations of Pb, Zn and Cd in flooded subsurface mine waste materials, natural or treated with organic carbon (OC) and/or sulfur (S), by combining advanced microbiological and X-ray spectroscopic techniques to determine the effects of treatments on the microbial community structure and identify the dominant functional genes involved in the biogeochemical transformations, especially metal sulfide formation over time. Samples collected from medium-, and long-term submerged columns were used for microarray analysis via functional gene array (GeoChip 4.2). The total number of detected gene abundance decreased under long-term submergence, but major functional genes abundance was enhanced with OC plus S treatment. The microbial community exhibited a substantial change in structure in response to OC and S addition. Sulfur-reducing bacteria genes dsrA/B were identified as key players in metal sulfide formation via dissimilatory sulfate reduction. Uniqueness of this study is that microbial analyses presented here in details are in agreements with molecular-scale synchrotron-based X-ray data supporting that OC-plus-S treatment would be a promising strategy for reducing metal toxicity in mine waste materials.

Synergy, emerges from synchronized reciprocal positive feedback loops between a network of diverse actors. For this process to proceed, compatible information from different sources synchronically coordinates the actions of the actors resulting in a nonlinear increase in the useful work or potential energy the system can manage. In contrast noise is produced when incompatible information is mixed. This synergy produced from the coordination of different agents achieves non-linear gains in free energy and in information (negentropy) that are greater than the sum of the parts. The final product of new synergies is an increase in individual autonomy of an organism that achieves increased emancipation from the environment with increases in productivity, efficiency, capacity for flexibility, self-regulation and self-control of behavior through a synchronized division of ever more specialized labor. Examples that provide quantitative data for this phenomenon are presented. Results show that increases in free energy density require decreases in entropy density. This is proposed as a law of thermodynamics.

Raw materials used for producing concrete, such as sand and gravel, are in short supply worldwide. It has been reported that the production of cement, one of the main constituents of concrete, results in the emission of a large amount of CO₂, accounting for 8% of total global CO₂ emissions. In this study, we developed a method to produce a construction material using only sand as the solid raw material. By utilizing a technique to produce organic silicon material from sand, we placed sand, alcohol, and catalyst in a closed vessel and heated it to 240 °C. After 24 h, the sand particles were bonded to each other, and a hardened body was formed. A tradeoff in production conditions, such as temperature, time, and the amount of sand, was confirmed.

Objetives/Background: Vitamin D Binding Protein (VDBP) and free vitamin D are new markers that are being studied as a possible markers of vitamin D status. The main aim of our study was to analyse the VDBP genotype and quantify the levels of VDBP and free vitamin D in a sample of cystic fibrosis (CF) patients. Methods: Multicentre, cross-sectional and prospective study including patients with CF, exocrine pancreatic insufficiency who were clinically stable. We investigated vitamin D levels (total and free) and the different VDBP haplotypes. Free vitamin D levels were measured using an electro-chemiluminescence assay. Results: A sample of 48 patients was obtained (52% male; median age 13.8 years). The most common allele of VDBP was Gc1s (72%)>Gc2 (52%)>Gc1f (27%). Median calcidiol was 21.2 ng/ml (IR 15.3 - 26.9), 81% had levels in the insufficiency range: 23 patients (48%) below 20 ng/ml, and 16 (33%) between 20 and 30 ng/ml. The median free vitamin D level was 4.2 pg/ml (IR 3.9 – 5.6). A positive correlation was observed between calcidiol and free vitamin D levels (r=0.871; p<0.0001). After adjustment for season, vitamin D supplementation, sex and CFrelated diabetes, patients with Gc1f polymorphism had a lower risk of vitamin D deficiency, OR 0.22 (95% CI 0.05 – 0.99), p=0.027. A negative linear trend was observed between the polymorphisms grouped into 3 categories (Gc1/Gc1, Gc1/Gc2, and Gc2/Gc2, in that order) and vitamin D and free vitamin D levels (p=0.025 and p=0.033, respectively). Conclusion: In CF, as in the general population, the most common VDBP haplotype in Caucasian race is Gc1s. VDBP polymorphisms influence serum vitamin D and free vitamin D levels in CF patients. There is a good correlation between free vitamin D and calcidiol levels, suggesting that measuring the latter in CF does not seem to provide any additional benefit.

Development of methods and algorithms to predict the effect of mutations on protein stability, protein-protein, and protein-DNA/RNA binding is necessitated by the needs of protein engineering and for understanding the molecular mechanism of disease-causing variants. The vast majority of the leading methods are either methods with adjustable parameters or machine learning algorithms, both requiring a database of experimentally measured folding and binding free energy changes. These databases are collections of experimental data taken from scientific investigations typically aimed at probing the role of particular residue on the above-mentioned thermodynamics characteristics, i.e., the mutations are not introduced at random and do not necessarily represent mutations originating from single nucleotide variant (SNV). Thus, the reported performance of the leading algorithms assessed on these databases or other limited cases, may not be applicable for predicting the effect of SNVs seen in the human population. Indeed, we demonstrate that the SNVs and non-SNVs are not equally presented in the corresponding databases and the distribution of the free energy changes are not the same. Furthermore, the Pearson correlation coefficients (PCCs) obtained on cases involving SNVs are less impressive than for non-SNVs, indicating that caution should be used in applying them to reveal the effect of human SNVs. All methods are found to underestimate the energy changes by roughly a factor of 2.

Acute kidney injury (AKI) is a common complication post-cardiac surgery, impacting short- and long-term survival. Free light chains (FLCs) are being explored as markers for assessing kidney damage risk. A study aimed to validate early AKI detection by studying FLCs (kappa, lambda, and kappa/lambda ratio) in serum and saliva samples. Clinical data was collected from 149 patients who underwent cardiac surgery in Baghdad. Ninety of these patients provided saliva samples in addition to serum samples for free light chain evaluation. Patients were grouped by proteinuria severity. Serum kappa levels were significantly higher in severe proteinuria patients compared to mild or no proteinuria. Salivary kappa levels were significantly higher in mild proteinuria patients compared to severe or no proteinuria. Salivary lambda levels decreased with increasing proteinuria severity. Serum kappa increase could be due to immune system activation and kidney compromise. Both serum and salivary kappa showed good predictive ability for post-surgery AKI prognosis compared to lambda and the kappa/lambda ratio, depending upon ROC performance. The study suggests FLCs, especially kappa, could be valuable in early AKI detection post-cardiac surgery, indicating potential for improved patient outcomes through proactive monitoring and intervention.

Facebook (FB) is the most popular online networking platform. There are several FB pages dedicated to spreading awareness about the Celiac disease (CD). To get the latest information, a huge number of CD patients follow Celiac disease Facebook (CD-FB) pages. Such pages frequently post beneficial information. However, very less is known if they provide appropriate information to CD patients. We conducted this study to know if CD-FB pages spread misleading information to CD patients. CD-FB pages from three celiac-influenced countries were explored using the FB platform and Google search engine. From October 2021 to April 2022, a total of 147 CD-FB, Italy (n=63), the USA (n=46), and India (n=38), were found eligible. Of them, 13% of pages (followers Mean±SD; Italy 2478±2011; USA 12635±12486; India 667±313) shared misleading information, particularly about gluten-free ingredients, and treatment of CD. In total,16% of CD-FB pages discussed alternative treatments option. Surprisingly, 7% of pages (followers Mean±SD; USA 23800±10465; India 628±333) supported alternative treatments for CD. CD-FB pages are useful for disseminating celiac-related information. While most of such pages provide useful information, a few pages sometimes contain misleading information. CD patients must consult their treating unit before following any uncertain information posted on CD-FB pages.

The antioxidant activity of molecules constitutes an important factor for the regulation of redox homeostasis and reduction of oxidative stress. Cells affected by oxidative stress can undergo genetic alteration, causing structural changes and promoting the onset of chronic diseases, such as cancer. The in silico study performed here was developed to evaluate the antioxidant potential of two molecules, ZINC08706191 (Z91) and ZINC08992920 (Z20), with recognized epithelial anticancer potential. Molecular docking, chemical-quantum calculations and Pearson's correlation were performed. The Z91 and Z20 molecules showed lower binding free energy (ΔG) values for the receptor-ligand interaction than the reference molecules (caffeine – CAF and ascorbic acid – AA), and better results for values of molecular descriptors correlated with ΔG, resulting in a decrease of ΔG. Strong correlations were observed between ΔG values for the five receptors evaluated and ΔG values of the potential epithelial anticancer activity available in literature. These results attest to the significant antioxidant potential of the Z91 and Z20 molecules and their strong relation with the potential epithelial anticancer activity and may be indicated for further analysis in relation to the control of oxidative stress and epithelial anticancer activity.

The present paper addresses dynamic risks in the automotive industry factories, specifically the car lead-acid batteries manufacturing area. The main analyzed risk is represented by the fire risk. Battery manufacturing process is described and analyzed from the fire risk perspective and the hazard areas are identified. The investigation methodology uses case studies for different lead-acid battery formation processes, combined with 3D simulations using PyroSym platform, and it is based on the author's experience in the battery manufacturing field for about ten years. The results of the case studies are compared using the same inputs, but different specific process conditions, and conclusions are formulated. To avoid the fires and mitigate the risk, a series of actions are proposed in the last sections. As a general conclusion, the actual research demonstrates that the complex and dynamic risks from the automotive industry, associated with Industry 5.0 must be analyzed using combined methods, classical and modern, including 3D simulations, to get great results.

To assess contamination levels, sources, and ecological health risks of potentially toxic elements (PTEs) in the sediments of Al Lith on the Saudi Red Sea coast, 25 samples were collected and analyzed for Zn, V, Cr, Cu, Ni, As, Pb, and Fe using ICP-AES. The average concentrations of PTEs (μg/g) were found in the following order: Fe (14259) > V (28.30) > Zn (22.74) > Cr (16.81) > Cu (12.41) > Ni (10.63) > As (2.66) > Pb (2.46). Contamination indices indicated that Al Lith sediments exhibited either no or minimal enrichment of PTEs, with concentrations below the low effects range. This suggests that the primary source of these PTEs is the basement rocks of the Arabian Shield and that they are unlikely to pose a substantial risk to benthic communities. The hazard index (HI) values for PTEs in both adults and children were below 1.0, indicating no significant non-carcinogenic risk. Lifetime cancer risk (LCR) values for Pb, As, and Cr in both adults and children were within acceptable or tolerable levels, posing no significant health threats. However, a few samples showed LCR values exceeding 1 × 10-4, indicating potential risks.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

The Lead-DBS imaging toolbox reconstructs the location of β-oscillations in the subthalamic nucleus (STN) in patients with Parkinson’s disease. The objective was to compare this probabilistic location with those of intraoperative monopolar β-oscillations (Vercise Cartesia directional electrodes, Boston Scientific). Also, the efficacy of stimulated structures in reducing motor symptoms were analysed. β-oscillations were computed from local field potentials [0.5-3kHz] by using shielded wires for monopolar recordings with an extracranial shielded reference. For each electrode contact, power spectral densities of the β-band [13-31Hz] were compared with those of all eight electrode contacts. The DISTAL, electrophysiological, and DBS target atlases of the Lead-DBS toolbox were applied to the reconstructed electrodes from preoperative MRI and postoperative CT. Thirty-six electrodes (20 patients: 7 female, 13 male; 16/20 both, 4/20 single STN) were analysed. Stimulation sites dorsal and/or lateral to the sensorimotor STN were most efficient. In 33/36 electrodes at least one contact was measured with stronger β-oscillations, 23 in or touching the ventral subpart of the probabilistic volume with β-oscillations, 10 not located in or touching but adjacent to this volume; in 3/36 electrodes, no contact was found with β-oscillations, they were distant from this volume. Monopolar local field potentials confirmed the ventral subpart of the probabilistic β-oscillations.

This paper presents the results of an experimental study of the patterns of steel and lead shot transformation under the impact of environmental factors (two types of shot exposed alone and in combination with each other). The analyzed environmental factors include atmospheric precipitation of various acidity and soil solutions with a higher content of organic acids. This research demonstrated that steel shot is characterized by a high transformation rate that is an order of magnitude higher on average than the transformation rate of lead under the same conditions. The prevalence of the suspended iron form (excluding the interaction with organic acids) presents risks for such environmental components as soils and sediments and may be hazardous to the ambient air and natural waters in case of wind erosion and surface runoff from the catchment area. Furthermore, the joint presence of steel and lead shot mutually accelerates the corrosion of both metals, thus increasing the environmental risks.

In this study, we improved the photovoltaic (PV) properties and storage stabilities of inverted perovskite solar cells (PVSCs) based on methylammonium lead iodide (MAPbI3) by employing bathocuproine (BCP)/poly(methyl methacrylate) (PMMA) and BCP/polyvinylpyrrolidone (PVP) as hole-blocking and electron-transporting interfacial layers. The architecture of the PVSCs was indium tin oxide/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/MAPbI3/[6,6]-phenyl-C61-butyric acid methyl ester/BCP:PMMA or BCP:PVP/Ag. The presence of PMMA and PVP affected the morphological stability of the BCP and MAPbI3 layers. The storage-stability of the BCP/PMMA-based PVSCs was enhanced significantly relative to that of the corresponding unmodified BCP-based PVSC. Moreover, the PV performance of the BCP/PVP-based PVSCs was enhanced when compared with that of the unmodified BCP-based PVSC. Thus, incorporating hydrophobic polymers into BCP-based hole-blocking/electron-transporting interfacial layers can improve the PV performance and storage stability of PVSCs.

Lead exposure is associated with poor cognitive development in children. Very few studies in sub-Saharan Africa (SSA) have studied blood lead levels (BLLs) and non-gasoline sources of exposure in children. Data from a birth cohort in Benin (2011-2013) suggested that 58% of one-year-old children had BLLs > 50 ug/L. We aimed to investigate the prevalence of elevated BLLs (>50 µg/L and >100 µg /L) among 425 of these children at six-years-of-age in 2016-18 and to compare BLLs between age one-year and six-years and study sources of lead at six years. BLLs were analyzed by inductively coupled plasma mass spectrometry. Multiple linear regression and quantile regressions were used to study potential sources of lead. The prevalence of BLLs >50 µg/L in children was 59.5% [Geometric Mean (GM) 56.4 µg/L, 95% CI: 54.1 - 58.7] at six years of age compared to 54.8% [GM 56.5 µg/L, 95% CI: 53.4-59.6] at one year of age. The prevalence of children with BLLs >100 µg/L decreased from 14.4% at one year of age to 8.2% at six years of age. After adjustment for all other covariates, consumption of peanut more than once per month was significantly associated with a 22.0% (95% CI: 4.6, 42.5) increment in BLLs at six years compared with no consumption. Consumption of bushmeat killed by lead bullets at six years was associated with an increase in the higher percentiles of BLLs (P75) compared with the absence of this source. Other potential sources of lead associated with BLLs with marginal significance were consumption of rice, paternal occupational exposure, and the presence of activity with the potential use of lead. This prospective cohort confirms the persistently high prevalence of elevated BLLs in children residing in a rural region in the south of Benin as well as the presence of multiple and continuous sources of lead. These results highlight the need for prevention programs to reduce and eliminate lead exposure in children.

Despite the 12-lead electrocardiogram (ECG) being the gold standard in evaluating clinical presentations of arrythmias of various kinds, several notable limitations, namely in accuracy and localization, have recently garnered concern with respect to administering appropriate therapeutic measures. The following text puts these limitations under the spotlight, highlighting the difficulty and challenging nature of standard ECG analysis and therapeutic measures, while simultaneously showing a novel body surface electrocardiographic mapping system that utilizes 3D spatial imaging and pinpoint localization algorithms in order to compensate for the shortcomings of the standard ECG, thereby providing higher precision data collection. We provide a brief overview of the novel device in a selection of arrhythmic demographics, along with its validity and reliability, while illustrating the benefits and positive outcomes of its utility.

In cancer, the lymphatic system is hijacked by tumor cells to escape from primary tumor and to metastasize to the sentinel lymph nodes. Tumor lymphangiogenesis is stimulated by the vascular endothelial growth factors-C (VEGFC) after binding to its receptor VEGFR-3. However, how VEGFC cooperates with other molecules to promote lymphatic neovessels growth is not fully determined. Here, we found that tumor lymphangiogenesis developed in tumoral lesions and in their surrounding adipose tissue (AT). Interestingly, lymphatic vessel density correlated with an increase of circulating free fatty acids (FFA) in the lymph from tumor-bearing mice. We found that adipocyte-released FFA are uploaded by lymphatic endothelial cells (LEC) to stimulate their sprouting. Lipidomic analysis identified the monounsaturated oleic acid (OA) as the major circulating FFA in the lymph in tumoral context. OA transporters FATP-3, -6 and CD36 were only upregulated on LEC in the presence of VEGFC showing a collaborative effect of these molecules. OA released from adipocytes is taken up by LECs to stimulate the fatty acid β-oxidation, leading to increase adipose tissue lymphangiogenesis. Our results provide new insights on the dialogue between tumors and adipocytes via the lymphatic system and identify a key role for adipocyte-derived FFA in the promotion of lymphangiogenesis, revealing novel therapeutic opportunities for inhibitors of lymphangiogenesis in cancer.

It has been recognized for some time that even for perfect conductors, the interaction Casimir entropy, due to quantum/thermal fluctuations, can be negative. This result was not considered problematic because it was thought that the self-entropies of the bodies would cancel this negative interaction entropy, yielding a total entropy that was positive. In fact, this cancellation seems not to occur. The positive self entropy of a perfectly conducting sphere does indeed just cancel the negative interaction entropy of a system consisting of a perfectly conducting sphere and plate, but a model with weaker coupling in general possesses a regime where negative self-entropy appears. The physical meaning of this surprising result remains obscure. In this paper we re-examine these issues, using improved physical and mathematical techniques, partly based on the Abel-Plana formula, and present numerical results for arbitrary temperatures and couplings, which exhibit the same remarkable features.

In Philadelphia chromosome positive B-cell (Ph+) acute lymphoblastic leukemia (LLA), growing evidence has ac-cumulated about the efficacy of low-intensity and chemo-free regimens. Our objective was to analyze all recent trials evaluating these treatments and to compare them in terms of efficacy. We applied the Shiny method, an artificial intelligence technique, to analyze Kaplan-Meier curves and reconstruct patient-level data. Reconstructed patient data were then evaluated through standard survival statistics and subjected to indirect head-to-head treatment comparisons. The endpoint was progression-free survival (PFS). Based on 848 reconstructed patients, 9 trials were analyzed. The survival data from these trials were pooled into three types of treatments: i) treatments based on ty-rosine kinase inhibitors (TKIs) combined with reduced-intensity chemotherapy (denoted as TKICHE); ii) TKIs as-sociated to steroids with no chemotherapy (TKISTE); iii) chemotherapy-free combinations of blinatumomab plus TKIs (TKIBLI). According to the Shiny method, the three PFS curves were reported in a single Kaplan-Meier graph and subjected to survival statistics. In terms of PFS, TKIBLI ranked first, TKICHE second, and TKISTE third; the differences between these three regimens were statistically significant. This multi-treatment Kaplan-Meier graph, generated through the Shiny method, summarized the current evidence on these treatments in both qualitative and quantitative terms.

High seismic activity in the Himalayas and the increasing urbanization of its surrounding areas in the northern Indian region pose significant threats to both lives and properties. To mitigate the risk of seismic events, an earthquake early warning system can be used in the region. This system would be particularly beneficial to cities and towns in the mountainous and foothill regions that are located near earthquake sources. The government and the science and engineering community have re-sponded to this call by establishing the Uttarakhand State Earthquake Early Warning System (UEEWS). The system became fully operational on August 4, 2021, after being launched by the government of Uttarakhand. The UEEWS includes 170 accelerometers in the seismogenic part of the Uttarakhand region of the Himalayas. Ground motion data is transmitted to a central server through a dedicated private telecommunication network 24 hours a day, seven days a week.The system is designed to issue warnings for moderate to high-magnitude earthquakes via a mobile application installed on users' devices and sirens installed in government-owned public buildings. The UEEWS has successfully issued alerts for light earthquakes that occurred in the instrumented region and warnings for moderate earthquakes that occurred in the vicinity of the instrumented area. This paper provides an overview of the design of the UEEWS, details of the instrumentation, adaptation of attributes and their relation to earthquake parameters, the operational flow of the system, and information about the dissemination of warnings

The inner walls of drinking water distribution system (DWDS) are expected to be clean to ensure a safe quality of drinking water. In reality, complex physical, chemical and biological processes take place when water comes into contact with the pipe surface. This paper describes the impact of leaching different compounds from the water supply pipes into the drinking water and subsequent risks. Among these compounds there are heavy metals. It is necessary to prevent these metals to get into the DWDS. Those compounds are susceptible to impact the quality of the water delivered to population either by leaching dangerous chemicals into the water or by enhancing the development of microorganism growth on the pipe surface. The corrosion process of different pipes materials, scale formation mechanisms and the impact of bacteria formed in corrosion layers are discussed. Water treatment processes and the pipe materials also affect the water composition. Pipes materials act differently in the flowing and stagnation conditions. Also, they age differently (e.g metal based pipes are subjected to corrosion while polymer based pipes have a decreased mechanical resistance) and are susceptible to enhance bacterial film formation. This review helps to clarify what are the possible sources of compounds responsible for drinking water quality degradation. Also, it gives guidance on the measures that are needed to maintain a stable and safe drinking water quality.

Abstract: Background: The Hospital-at-home (HAH) model is a viable alternative for conven-tional in-hospital stays worldwide. Serum electrolyte abnormalities are common in acute pa-tients, especially in those with many comorbidities. Pathologic changes in cardiac electrophysi-ology pose a potential risk during HAH stay. Periodical Electrocardiogram (ECG) tracing is therefore advised, but few studies evaluated the accuracy and efficiency of compact, self-activated ECG devices in the HAH settings. This study aimed to evaluate the reliability of such a device in comparison to a standard 12-lead ECG. Methods: We prospectively recruited consecu-tive patients admitted to the Sheba Beyond, virtual hospital, in the HAH department, during a 3-month duration. Each patient underwent a 12-lead ECG recording using the legacy device, and a consecutive recording by a compact 6-lead device. Baseline patients’ characteristics during hospi-talization were collected. Level of agreement between devices was measured by Cohen’s Kappa coefficient for inter-rater reliability (Ϗ). Results: Fifty patients were included in the study. 26 (52%) had electrolyte disturbances. Abnormal D-dimer values were observed in 33 (66%) pa-tients, and 12 (24%) patients had elevated troponin values. We found a level of 94.5% raw agreement between devices with regards to nine of the options included in the automatic read-out of the legacy device. The calculated Ϗ was 0.72, classified as substantial consensus. The rate of raw consensus regarding ECG intervals’ measurement (PR, RR, QT) was 78.5% and the calculated Ϗ was 0.42, corresponding to a moderate level of agreement. Conclusion: This is the first report to our knowledge regarding the feasibility of using a compact, 6-Lead ECG device in the setting of HAH to be safe and bearing satisfying agreement level with a legacy, 12-lead ECG device, en-abling quick, accessible arrythmia detection in this setting. Our findings bear a promise to the future development of telemedicine-based hospital at home methodology.

Background: Trans-septal endocardial left ventricle lead placement is an alternative technique used capture the left ventricular endocardially but it is use is limited due lack of evidence, practice uptake and clinical trials. we evaluated the efficiency of the procedure, post procedural complication rate, rate of thromboembolic events as well as changes in echocardiographic parameters, brain natriuretic peptide (BNP) level and the New York Heart Association (NYHA) class. Results: TSLV lead implant is safe, improves ejection fraction, LVEDV, LVESV, LVIDd. Significantly reduces NTproBNP levels and NYHA class. Stroke rate was reported only in one patient (9%), noticeably, this particular patient was on DOAC rather than anti-vitamin K antagonists. In this group, patients, who were on Warfarin , were not reported to have any thrombo-embolic events. Discussion: Trans-septal endocardial LV lead implant in patients with a failed CS approach remains a viable alternative however, there is a higher risk of stroke amongst these patients, as well as more procedure related risk of complications compared to conventional CRT. The data analysis demonstrates that patients undergoing a TSLV lead implant due to a failed trans-venous approach have more advanced heart failure, defined by their higher NYHA class compared to conventional trans-venous CRT implant groups. Their pre TSLV implant, echocardiographic parameters are also worse compared to trans-venous CRT implant group

In response to long-lasting high levels of Metallic Trace Elements (MTEs) in urban soils, we expect soil invertebrates inhabiting urban environments to have evolved detection and avoidance and/or tolerance mechanisms to MTE pollution. In this study, I used artificial soils with concentrations of lead, zinc, copper, chromium and nickel that reflect pollution levels in soils of Parisian parks. Using choice experiments, I compared habitat preference (i.e. the occurrence of individuals in the polluted vs. unpolluted soil) and health status (i.e. body mass maintenance, mobility, mortality) between three species of endogeic earthworms – Apporectodea caliginosa, Apporectodea icterica and Allolobophora chlorotica – originating either from urban or rural grasslands. This study highlights a clear avoidance of MTE polluted soils in all three species, as well as MTE-induced health impairments, especially in A. chlorotica. Interestingly, earthworm response to MTE exposure only slightly differed between earthworms from urban and rural origin, suggesting the absence of widespread acclimatization or adaptation mechanisms to MTE pollution in cities. As a consequence, MTE pollution is expected to significantly shape earthworm spatial distribution in both urban and rural environments and, as a consequence, affect ecosystem functioning.

The heavy metal lead (Pb) can irreversibly damage the human nervous system. To help understand Pb-induced damage, we applied a genetically encoded Förster resonance energy transfer (FRET)-based Pb biosensor Met-lead 1.44 M1 to two living systems to monitor the concentration of Pb: induced pluripotent stem cell (iPSC)-derived cardiomyocytes as a semi-tissue platform, and Drosophila melanogaster fruit flies as an in vivo animal model. Different FRET imaging modalities were used to obtain FRET signals, which represented the presence of Pb in the tested samples in different spatial dimensions. Using iPSC-derived cardiomyocytes, the relationship between beating activity (20–24 beats per minute, bpm) determined from the fluctuation of fluorescent signals and the concentrations of Pb represented by the FRET emission ratio values of Met-lead 1.44 M1 was revealed from simultaneous measurements. Pb (50 μM) affected the beating activity of cardiomyocytes, whereas two drugs that stop the entry of Pb differentially affected this beating activity: verapamil (2 μM) did not reverse the cessation of beating, whereas 2-APB (50 μM) partially restored this activity (16 bpm). The results clearly demonstrate a potential of this biosensor system as an anti-Pb drug screening application. In the Drosophila model, Pb was detected within the adult brain or larval central nervous system (Cha-gal4>UAS-Met-lead 1.44 M1) using fast epifluorescence and high-resolution two-photon 3D FRET ratio image systems. The tissue-specific expression of Pb biosensors provides an excellent opportunity to explore the possible Pb-specific populations within living organisms. We believe that this integrated Pb biosensor system can be applied to the prevention of Pb poisoning and advanced research on Pb neurotoxicology.

Lead (Pb) is a toxic environmental heavy metal that induces serious clinical defect on all organs with the nervous system being the primary target. Curcumin is the main active constituent of turmeric rhizome (Curcuma longa) with strong antioxidant and anti-inflammatory properties. This study is aimed at evaluating the therapeutic potentials of curcumin on Pb-induced neurotoxicity. Thirty six male Sprague Dawley rats were randomly assigned into five (5) groups with 12 rats in the control (normal saline) and 6 rats for the lead treated group (LTG) (50 mg/kg lead acetate for 4 weeks), recovery group (RC) (50 mg/kg lead acetate for 4 weeks), treatment group 1 (Cur100) (50 mg/kg lead acetate for 4 weeks, followed by 100 mg/kg curcumin for 4 weeks) and treatment group 2 (Cur200) (50 mg/kg lead acetate for 4 weeks, followed by 200 mg/kg curcumin for 4 weeks) groups each. All experimental groups received the oral treatments through orogastric-tube on alternate days. Motor function was assessed using horizontal bar method while Pb concentration in the cerebellum of the rats were evaluated using ICP-MS techniques. Pb-administered rats showed significant decrease in motor scores, SOD activity with increase MDA levels and Pb concentration in their cerebellum with marked alterations in the histological architecture of the cerebellar cortex layers. However, treatment with curcumin improved the motor score, reduced Pb concentration in the cerebellum and ameliorates the markers of oxidative stress as well as restored the histological architecture of the cerebellum. The results this in study suggested that curcumin attenuates Pb-induced neurotoxicity via inhibition of oxidative stress and chelating activity.

Lead (Pb) is a toxic environmental heavy metal that induces serious clinical defect on all organs with the nervous system being the primary target. Curcumin is the main active constituent of turmeric rhizome (Curcuma longa) with strong antioxidant and anti-inflammatory properties. This study is aimed at evaluating the therapeutic potentials of curcumin on Pb-induced neurotoxicity. Thirty six male Sprague Dawley rats were randomly assigned into five (5) groups with 12 rats in the control (normal saline) and 6 rats for the lead treated group (LTG) (50 mg/kg lead acetate for 4 weeks), recovery group (RC) (50 mg/kg lead acetate for 4 weeks), treatment group 1 (Cur100) (50 mg/kg lead acetate for 4 weeks, followed by 100 mg/kg curcumin for 4 weeks) and treatment group 2 (Cur200) (50 mg/kg lead acetate for 4 weeks, followed by 200 mg/kg curcumin for 4 weeks) groups each. All experimental groups received the oral treatments through orogastric-tube on alternate days. Motor function was assessed using horizontal bar method while Pb concentration in the cerebellum of the rats were evaluated using ICP-MS techniques. Pb-administered rats showed significant decrease in motor scores, SOD activity with increase MDA levels and Pb concentration in their cerebellum with marked alterations in the histological architecture of the cerebellar cortex layers. However, treatment with curcumin improved the motor score, reduced Pb concentration in the cerebellum and ameliorates the markers of oxidative stress as well as restored the histological architecture of the cerebellum. The results this in study suggested that curcumin attenuates Pb-induced neurotoxicity via inhibition of oxidative stress and chelating activity.

Drinking water contamination of lead from various environmental sources, leaching consumer products and intrinsic water-pipe infrastructure is still today a matter of great concern. Therefore, new highly sensitive and convenient Pb²⁺ measurement schemes are necessary, especially for in-situ measurements at a low-cost. Within this work dye/ionophore/Pb²⁺ co-extraction and effective water phase de-colorization was utilized for highly sensitive lead measurements and sub-ppb naked-eye detection. A low-cost ionophore Benzo-18-Crown-6-ether was used, and a simple test-tube mix and separate procedure was developed. Instrumental detection limits were in the low ppt region (LOD=3, LOQ=10), and naked-eye detection was 500 ppt. Note, however, that this sensing scheme still has improvement potential as concentrations of fluorophore and ionophore were not optimized. Artificial tap-water samples, leached by a standardized method, demonstrated drinking water application. Implications for this method are convenient in-situ lead ion measurements.

Novel collector lead(II)-benzohydroxamic acid (Pb(II)-BHA) complexes in aqueous solution were characterized by using experimental approaches, including Ultraviolet-visible (UV-Vis) spectroscopy and electrospray ionization–mass spectrometry (ESI-MS), as well as first-principle density functional theory (DFT) calculations with consideration for solvation effects. The Job plot delineated that a single coordinated Pb(BHA)⁺ should be formed first, and the higher coordination number complexes can be formed subsequently. Moreover, the Pb(II)-BHA species can aggregate with each other to form complicated structures, such as Pb(BHA)₂ or highly complicated complexes. ESI-MS results validated the existence of Pb-(BHA)_n=1,2 under different solution pH values. Further, the first-principles calculations suggested that Pb(BHA)⁺ should be the most stable structure, and the Pb atom in Pb(BHA)⁺ will act as an active site to attack nucleophiles. These findings are meaningful to further illustrate the adsorption mechanism of Pb(II)-BHA complexes in mineral processing.

Lead, known as a metal with high neurotoxicity to children, cadmium, which is a carcinogenic and bioaccumulative contaminant, and arsenic, a class 1 carcinogenic according to the International Agency for Research on Cancer, are toxic elements (TEs) whose relevant route of exposure may be diet. We determined the bio-accessible fraction of lead, cadmium, and arsenic from the diet of preschool children from two day care centers (DCC). A cross-sectional study was conducted with 64 one–four-year-old children from two DCCs where the 24-h duplicate diet samples were collected. The diet samples were analyzed by ICP-MS for lead, cadmium, and arsenic total concentrations (n = 64) and their bio-accessibility were analyzed for a subsample (n = 10). The dietary intake (DI) mean for lead, cadmium, and arsenic were 0.18 ± 0.11 µg kg⁻¹ bw, 0.08 ± 0.04 µg kg⁻¹ bw, and 0.61 ± 0.41 µg kg⁻¹ bw, respectively. All DI calculated for TEs, considering total intake, were found lower than the tolerable limits (TL) (European Union, or World Health Organization, WHO, when applicable) except for one child’s Pb intake. Bio-accessibilities ranged between 0% to 93%, 0% to 103%, and 0% to 69%, for lead, cadmium, and arsenic, respectively. Although DI for TEs has been found lower than TL, these reference values have been recently decreased or withdrawn since it was for lead and arsenic whose TL were withdrawn by WHO.

High mountain areas are an appropriate indicator of anthropogenic lead (Pb), which can reach the remote mountain ranges through long distance atmospheric transport. We compared the content of Pb in ecologically equivalent rodent species from Tian-Shan with European mountain ranges Tatra, Vitosha and Rila mountains. We used bone tissues from terminal tail vertebrae of small rodents for detection of Pb levels by using electrothermal atomic absorption spectroscopy (AAS). The tail bones of Tian-Shan rodents had significantly lower Pb levels than snow voles from Tatra mountains, but there was no significant difference in comparison with Vitosha and Rila mountains. We can conclude that Tian-Shan shows lower pollution by Pb than Tatra mountains, what may be a reason of longer lasting industrialization of north-western Europe and strongly prevailing west winds in Tatra mountains.

: In Philadelphia chromosome positive B-cell (Ph+) acute lymphoblastic leukemia (LLA), growing evidence has accumulated about the efficacy of low-intensity and chemo-free regimens. Our objective was to analyse all recent trials evaluating these treatments and to compare them in terms of efficacy. We applied the Shiny method, an artificial intelligence technique, to analyse Kaplan-Meier curves and reconstruct patient-level data. Reconstructed patient data were then evaluated through standard survival statistics and subjected to indirect head-to-head treatment comparisons. The endpoint was progression-free survival (PFS). Based on 562 reconstructed patients, 8 trials were analyzed. The survival data from these trials were pooled into three types of treatment: i) treatments based on tyrosine kinase inhibitors (TKIs) combined with reduced-intensity chemotherapy (denoted as TKICHE); ii) TKIs associated to steroids with no chemotherapy (TKISTE); iii) chemotherapy-free combinations of blinatumomab plus TKIs (TKIBLI). According to the Shiny method, the three PFS curves were reported in a single Kaplan-Meier graph and subjected to survival statistics. In terms of PFS, TKIBLI ranked first, TKICHE second, and TKISTE third; the differences between these three regimens were statistically significant. In conclusion, the multi-treatment Kaplan-Meier graph generated in this study has effectively summarized the current evidence on these treatments in comparative terms.

Wastewater contaminated with antibiotics is a major environmental challenge. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in-situ synthesis of doped graphenes. The elements present in the natural polymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and the high absorption. In this mechanism, O2 dissolved in water absorbs onto the positive charged C in doped graphenes to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amounts of radicals and rate of antibiotic removal. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived grapheme shows the highest surface area, but lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. The effect of oxygen and light were also studied to accelerate the degradation process.