Synthesis of a novel series of chromen-3-yl-pyridine moieties. IR, NMR, and MS spectroscopy were used to confirm the structure of these novel compounds and study of antitumor activity of these compounds. The structure activity relationship investigation demonstrated that 2,4-diamino-5-(3-methoxyphenyl)-7-(2-oxo-2H-chromen-3-yl)-1,8-naphthyridine-3-carbonitrile (16), was more effective and naphthyridine-3-carbonitrile derivatives 17, 18 and pyrido[2,3-d]pyrimidine derivative 12, while compounds 5a,b, 9c, 11, 13 and 14 were moderate activity for antitumor activities.

This work aims to investigate the influence of reaction time and catalyst-to-residual fat ratio by catalytic upgrading from pyrolysis vapors of residual fat at 400 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, and acid value) and chemical composition of bio-oils, over a catalyst fixed bed reactor of activated carbon pellets impregnated with 10.0 M NaOH, in semi pilot scale. The experiments were carried out at 400 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 50, 60, 70, 80, 90, 100 and 120 minutes in order to investigate the process kinetics. The physicochemical properties (density, kinematic viscosity, and acid value) of bio-oils were determined by official methods. The chemical composition of bio-oils determined by GC-MS. The thermal catalytic cracking of residual fat show bio-oils yields from 55.55 to 30.22 (wt.%), aqueous phase yields between 2.83 and 3.19 (wt.%), solid phase yields between 13.56 and 9.75 (wt.%), and gas yields from 27.89 to 55.60 (wt.%). The yields of bio-oil decreases from 74.41 to 30.22% (wt.) with increasing catalyst-to-Tallow kernel oil ratio, while that of gaseous phase increases from 12.87 to 55.60% (wt.). For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of bio-oils decreases as the reaction time increases varying from 0.9266 to 0.8220 g/cm³, 8.10 to 2.24 mm²/s, and 144.14 to 2.37 mg KOH/g. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, ring-containing alkanes, ring-containing alkenes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the pyrolysis and catalytic cracking experiments, the hydrocarbon selectivity in bio-oil increases with increasing reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties density, kinematic viscosity, and acid value were 0.8220 g/cm³, 3.03 mm2/s, and 2.37 mg KOH/g, respectively, with a maximum hydrocarbon concentration of 97.194% (area.) and 2.806% ketones (area.) were obtained at 400 °C and 1.0 atmosphere, 80 minutes, without catalyst. For the catalytic cracking experiments, the maximum hydrocarbon content of 75.763% (area.) and 17.041% (area.) carboxylic acids, 4.702% (area.) ketones (area.), and 2.494% (area.) non-identified oxygenates was obtained at 400 °C and 1.0 atmosphere, 90 minutes, using a catalyst fixed bed reactor, with 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH as catalyst.

This study aligns with the 2030 United Nations Sustainable Development Goals- 3 which aim to “ensure healthy lives and promote well-being for all at all ages”. It contributes to the nascent literature stream on energy-health dynamics by introducing a holistic theoretical model to empirically examine the mediation effect of carbon emissions on the relationship between nonrenewable energy and infant mortality rates. Using an unbalanced panel data on 42 Asia and the Pacific countries from 2005 to 2015 and deploying the structural equation modeling approach, the empirical results are surmised as follows: (i) in regard to the full sample of countries, nonrenewable energy indirectly increases infant mortality rates through increasing carbon emissions. In other words, carbon emissions play a partial mediation role between nonrenewable energy and infant mortality rates; and (ii) for the different income groups, carbon emissions show varying mediation effects. For example, the mediation effects of carbon emissions in lower-middle and upper-middle income countries are found to be similar to those of the full sample of countries. Therefore, based on these findings, we conclude that nonrenewable energy is an essential determinant of infant mortality rates. Policy recommendations are put forward.

Pd-Pt catalysts supported on carbon preheated to 1600°C have been reinvestigated in CHFCl2 hydrodechlorination. An additionally adopted catalyst oxidation at 350-400°C produced an order of magnitude increase in the catalytic activity of Pd/C. This increase is not caused by changes in metal dispersion or possible decontamination of the Pd surface from superficial carbon, but rather by unlocking the active surface, originally inaccessible in metal particles tightly packed in the pores of carbon. Burning carbon from the pore walls attached to the metal changes the pore structure, providing easier access for the reactants to the entire palladium surface. As upon calcination the performance of the rest of the Pd-Pt/C catalysts changes less than for Pd/C, the relation between the turnover frequency and alloy composition does not confirm the Pd-Pt synergy invoked in our previous work. The use of even higher-preheated carbon (1800°C), completely free of micropores, results in a Pd/C catalyst that does not need to be oxidized to achieve high activity and excellent selectivity up to CH2F2 (>90%).

Air change rate is an important parameter for quantification of ventilation heat losses and also affects the indoor climate of buildings. Indoor air quality is significantly associated with ventilation. If air change isn't sufficient, trapped allergens, pollutants and irritants can degrade the indoor air quality and affect the well-being of a building's occupants. Many studies on ventilation and health have concluded that lower air change rates can have a negative effect on people’s health and low ventilation may result in an increase in allergic diseases. Quantification of air change rate is complicated, since it is affected by a number of parameters, of which the one of the most variable is the air-wind flow. This study aims to determination and comparison of values of the air change rate in two methods - by quantifying of aerodynamic coefficient Cp = Cpe - Cpi – so called aerodynamic quantification of the building and the methodology based on experimental measurements of carbon dioxide in the selected reference room in apartment building.

Soil CO2 efflux (FCO2) plays a dominant role in the terrestrial carbon (C) cycle but interpreting constraints on local observations is impeded by challenges in disentangling belowground CO2 sources. Trees contribute most C to forest soils, so linking aboveground properties to FCO2 could open new avenues to study plant-soil feedbacks and facilitate scaling; furthermore, FCO2 responds dynamically to meteorological conditions, complicating predictions of total FCO2 and forest C balance. We tested for proximity effects of individual Acer saccharum Marsh. trees on FCO2, comparing FCO2 within 1 m of mature stems to background fluxes before and after an intense rainfall event. Wetting significantly increased background FCO2 (6.4±0.3 vs. 8.6±0.6 s.e. μmol CO2 m-2s-1), with a much larger enhancement near tree stems (6.3±0.3 vs. 10.8±0.4 μmol CO2 m-2s-1). FCO2 varied significantly among individual trees and post-rain values increased with tree diameter (with a slope of 0.058 μmol CO2 m-2s-1 cm-1). Post-wetting amplification of FCO2 (the ‘Birch effect’) in root zones often results from the improved mobility of labile carbohydrates and further metabolization of recalcitrant organic matter, which may both occur at higher densities near larger trees. Our results indicate that plant-soil feedbacks change through tree ontogeny and provide evidence for a novel link between whole-system carbon fluxes and forest structure.

Soil organic carbon (SOC) sequestration in arable soils is a challenging goal for soil management. Multiple factors should be considered for the prediction of the soil capacity to fix atmospheric carbon. In this study, we focused on the effect of crop rotation and previous land use for future carbon sequestration on two experimental fields with identical soils (Retisols) and input of organic fertilizers. We analyzed the SOC dynamics and used the Roth C model to forecast SOC changes under RCP4.5 and RCP8.5 scenarios. Our experimental and modelling results indicated a consistent increase in SOC stocks and the stable fractions of soil organic matter (SOM). The increase in SOC was higher in the experiment with the crop-grassland rotation that in the experiment with a rotation of row crops and barley. With similar total SOC stocks, the efficiency of soil management differed as reflected by the contrasting composition of SOM, as fields with a long cultivation history showed higher SOM stability. The goal of 4‰ annual increase of SOC stocks may be reached under crop- grassland rotation in 2020-40 and 2080-90 when applying mineral or organic fertilizer system for scenario RCP4.5, and mineral fertilizer system in 2080-2090 for scenario RCP8.5.

Biochar application to the soil can improve soil quality and nutrient leaching loss. Recent studies have reported that surficial application of biochar to stored swine manure can reduce emissions of odorous compounds and reduce the volatilization loss of ammonia. Our working hypothesis was that the biochar-treated manure application to the soil would decrease nutrient leaching from manure and increase plant-available nutrients. The study objectives were to evaluate the impact of biochar-treated swine manure on soil total C, N, and other major and minor nutrients. Three biochars (i) neutral pH red-oak (RO), (ii) highly alkaline autothermal corn (Zea mays) stover (HAP), and (iii) mild acidic Fe-treated autothermal corn stover (HAPE) were incubated with swine manure for a month. The biochar-manure mixture was applied in triplicate to soil columns with application rate determined by the P₂O₅-P content in manure or manure-biochar mixtures after the incubation. The ammonium (NH₄⁺), nitrate (NO₃^-), and reactive P concentrations in soil column leachates were recorded for eight leaching events. Soil properties and plant-available nutrients were compared between treatments and control manure & soil. Manure-(HAP&HAPE) biochar treatments significantly increased soil organic matter (OM) and increased soil total C, N, and improved soil bulk density. Concentrations of KCl-extractable NH₄⁺ and NO₃^- significantly increased in HAPE column leachates during this 4-week study and in the soil after the experiment. A significant reduction in soil Mehlich3 Cu was also observed for the manure-HAPE mixture compared with the control. Overall, the manure-biochar incubation enabled biochar to sorb nutrients from manure, and the subsequent manure-biochar mixture application to soil improved soil quality and plant nutrient availability in comparison to conventional manure application to soil. This proof-of-the-concept study suggests that biochars could be used to solve both environmental and agronomic challenges and further improve the sustainability of animal and crop production agriculture.

Bioenergy with carbon capture and sequestration (BECCS) is one strategy to remove CO2 from the atmosphere. To assess the potential scale and cost of CO2 sequestration from BECCS in the US, this analysis models carbon efficiencies and costs of biomass production, delivery, power generation, and CO2 capture and sequestration in saline formations. The analysis includes two biomass supply scenarios (near-term and long-term), two biomass logistics scenarios (conventional and pelletized), two generation technologies (pulverized combustion and integrated gasification combined cycle), and three cost accounting scenarios (gross cost, net cost after electricity revenues, and net cost after electricity revenues with avoided emissions from conventional power generation). Results show cost Mg-1 CO2 as a function of CO2 sequestered (simulating capture up to 90% of total CO2 sequestration potential) and associated spatial distribution of resources and generation locations for the array of scenario options. Under a near-term scenario using 222 million Mg yr-1 of biomass, up to 196 million Mg CO2 can be sequestered at scenario-average costs ranging from $60 to $158 Mg 1 CO2; under a long-term scenario using 823 million Mg yr-1 of biomass, up to 727 million Mg CO2 yr 1 can be sequestered at scenario-average costs ranging from $32 to $242 Mg-1 CO2. These costs are largely influenced by cost accounting scenario, and the CO2 sequestration potential may be reduced if future competing demand reduces resource availability. Results suggest there are multiple feedstock-logistics-generation pathways toward CO2 drawdown that could be incrementally trialed and monitored for environmental sustainability effects. Interactive visualization of results is available at [final link to be determined].

The sustainable production of food faces formidable challenges. Foremost is the availability of arable soils, which have been ravaged by the overuse of fertilizers and detrimental soil management techniques. As such, maintenance of soil quality, and reclamation of marginal soils, has become an increasingly important endeavor. Recently, there has been emerging interest in the use of biochar, a carbon rich, porous material thought to improve various aspects of soil performance. Biochar (BC) is produced through the thermochemical decomposition of organic matter at high temperature in an oxygen limited environment, in a process known as pyrolysis. Importantly, the source of organic material, or ‘feedstock,’ used in this process and different parameters of pyrolysis, especially temperature, determine the chemical and physical properties of biochar. Incorporation of BC impacts soil-water relations, tilth and nutrient status, pH, soil organic matter (SOM), and microbial activity. Soil amendment with BC has been shown to have an overall positive impact on soil health and crop productivity; however, initial soil properties need to be considered prior to the application of BC. There is an urgent need to understand the effects of long-term field application of BC and how it influences the soil microcosm. This knowledge will facilitate predictable enhancement of crop productivity and meaningful carbon sequestration.

Nanoparticles of platinum-group metals (PGM) on carbon supports are widely used as catalysts for a number of chemical and electrochemical conversions on laboratory and industrial scale. The newly emerging field of single atom catalysis focuses on the ultimate level of metal dispersion, i.e. atomically dispersed metal species anchored on the substrate surface. However, the presence of single atoms in traditional nanoparticle-based catalysts remains largely overlooked. In this work we use aberration-corrected scanning transmission electron microscope to investigate four commercially available nanoparticle-based PGM/C catalysts (PGM = Ru, Rh, Pd, Pt). We show that in addition to nanoparticles, single atoms are also present on the surface of carbon substrates. These observations raise questions about the role that single atoms play in conventional nanoparticle PGM/C catalysts. We critically discuss the observations with regard to the quickly developing field of single atom catalysis.

Sustainability in material purchasing is a growing area of research. Goods purchasing decisions strongly affect transportation path flows, vehicle consolidation, inventory levels and related obsolescence costs. Within a global sourcing context, companies experience the need of new decision making approaches capable to consider a large variety of factors, also linked with society and environment. Environmental impact assessment has become a key requirement for materials purchasing and transportation decisions since global warming is a rising concern both in academic and industrial researches. In fact, it is well known that the freight transport industry is responsible for large amounts of carbon emissions contributing to global warming. In this paper, we initially analyse and compare the environmental economic policies established by the International Governments in relation to the carbon trading systems adopted. Then, we develop a multi-objective lot sizing approach useful in practice to define the sustainable quantity to purchase when a Cap and Trade mitigation policy is present. We further analyse the model behaviour according to different carbon price values by demonstrating that carbon prices are still far too low to motivate managers towards sustainable purchasing choices.

A potassium bromide KBr material, which has been widely used as the key element in the Fourier spectrometers and as the output window of the IR-lasers, has been studied with good advantage via applying the carbon nanotubes in order to modify the potassium bromide surface. The laser oriented deposition method has been used to place the carbon nanotubes at the matrix material surface in the vertical position at the different electric field varied from 100 to 600 V×cm-1. The main idea of the improvement of the spectral properties of the potassium bromide structure is connected with the fact that the refractive index of the carbon nanotubes is substantially less than the refractive index of the studied material, and the small diameter of the carbon nanotubes allows one to embed these nano-objects in the voids of the lattice of the model matrix systems. Moreover, the mechanical characteristics and wetting features of the potassium bromide structures have been investigated under the condition mentioned above. Analytical and quantum-chemical simulations have supported the experimental results.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

Background: Oxytocin is recommended as the first-line choice for labor induction in term pregnant women with premature rupture of membranes (PROM); however, it can occasionally lead to failed induction and delivery complications. The primary objective of this study was to compare delivery information and outcomes following the administration of oxytocin infusion or oral low-dose misoprostol solution for labor induction in term PROM women with an unfavorable cervical condition. Methods: A prospective nested case-control study was conducted at a tertiary general hospital in China from March 2020 to February 2024, comparing oxytocin infusion and oral administration of 25ug misoprostol every 2 hours for labor induction in term PROM women with a Bishop score

A fundamental aspect in the evolution of Time-to-Digital Converters (TDCs) implemented within Field-Programmable Gate Arrays (FPGAs), given the increasing demand for detection channels, is the optimization of resource utilization. This study reviews the principal methodologies employed for implementing low-resource TDCs in FPGAs. It outlines the foundational architectures and interpolation techniques utilized to bolster TDC performances without unduly burdening resource consumption. Low-resource Tapped Delay Line, Vernier Ring Oscillator, and Multi-Phase Shift Counter TDCs, including the use of SerDes, are reviewed. Additionally, novel low-resource architectures are scrutinized, including Counter Gray Oscillator TDCs and interpolation expansions using Voltage-Temperature-Consumption stable IODELAYS. Furthermore, the advantages and limitations of each approach are critically assessed, with particular emphasis on resolution, precision, non-linearities, and, especially, resource utilization. A comprehensive summary table encapsulating existing works on low-resource TDCs is provided, offering a comprehensive overview of the advancements in the field.

The unprecedented progress in Artificial Intelligence (AI), particularly in deep learning algorithms with ubiquitous internet connected smart devices, has created a high demand for AI computing on the edge devices. This review studied commercially available edge processors, and the processors that are still in industrial research stages. We categorized state-of-the-art edge processors based on the underlying architecture, such as dataflow, neuromorphic, and Processing in-Memory (PIM) architecture. The processors are analyzed based on their performance, chip area, energy efficiency, and application domains. The supported programming frameworks, model compression, data precision, and the CMOS fabrication process technology are discussed. Currently, most of the commercial edge processors utilize dataflow architectures. However, emerging non-von Neumann computing architectures have attracted the industry in recent years. Neuromorphic processors are highly efficient for performing computation with fewer synaptic operations, and several neuromorphic processors offer online training for secured and personalized AI applications. This review found that the PIM processors show significant energy efficiency and consume less power compared to dataflow and neuromorphic processors. The future direction of the industry would be to implement state-of-the-art deep learning algorithms in emerging non-Von Neumann computing paradigms for low power computing on the edge devices.

Mortality in children accounts for 15% of all AIDS-related deaths globally, with a higher burden among Cameroonian children (25%), likely due to poor virological response. We sought to evaluate viral suppression (VS) and its determinants in a nationally representative paediatric and young adult population receiving antiretroviral therapy (ART). A cross-sectional and multicentric study was conducted among Cameroonian children (

Great Himalayan range with regions namely, Jammu & Kashmir, Ladakh and high altitude parts of north eastern states inherently experience high solar exposure, cold, arid climate and significantly challenging geography. With a scarcity of affordable public housing projects in these regions a grid enabled low energy residential prototype is proposed having the capability to operate on nearly zero consumption of heating and cooling energy with the application of indigenous and contemporary energy efficient passive design techniques. Preliminary study, development of design and reading of simulation results were applied for the performance and benefit analysis of the low energy building prototype. Analysis of the climatic zone further classified and narrowed the design criterion by confirming upon beneficial architectural components proven to be energy efficient. These architectural components include, optimization of direct solar gain and orientation of building envelope, modified trombe wall system, traditional sunrooms, solar chimney with openable vents, efficient spatial planning and compliance of relevant parameters such as window-wall-ratio (WWR). The proposed low energy housing for the economically weaker section is estimated to save nearly 50% of active fuel based household heating energy. Site has been planned in such a way that about 100% of required electricity can be generated from on site renewable energy for the proposed infrastructure, it is proven more beneficial if additional electricity is generated to offset the power supply and result in lower or subsidized electricity bills. Design is compliant to different codes relevant to energy conservation and low-income housing with an embodied carbon of about 1.2 kgCO2/m2 per dwelling unit giving ‘A’ grade in cradle to gate impacts. The findings and performance of this prototype can serve as a guideline for energy efficient design in low income group housing situated in severe cold and arid regions of India such as Ladakh (U.T.).

Background: The objectives were to evaluate: the safety and immunogenicity of nonavalent human papillomavirus (nHPV) vaccine in adult Spanish women living with HIV (WLHIV); the prevalence of anal and cervical dysplasia and nHPV vaccine genotypes in anus and cervix; and risk factors for high-risk HPV (HR-HPV) infection in anal mucosa. Methods In this single-center, open-arm, non-randomized clinical trial, nHPV vaccine was administered at 0, 2, and 6 months to WLHIV enrolled between February 2020 and November 2023, measuring vaccine antibody titers pre-vaccination and at 2, 6, and 7 months after the first dose. Cervical and anal cytology and HPV PCR genotyping studies were performed. Women with abnormal cytology and/or anal or cervical HPV infection at baseline underwent high-resolution anoscopy and/or colposcopy. Results: 122 participants were included with mean age of 49.6 years: 52.5% smoked; 10.7% had anal-genital condylomatosis; 38.5% infection by HR-HPV in anus and 25.4% in cervix, most frequently HPV-16; 19.1% had AIN1 and 3.1% CIN1 and CIN2. Vaccine administration did not modify viral-immunological status (CD4 [809±226.8 cells/uL vs. 792.35 ±349.95; p=0.357]) or plasma HIV load (3.38±4.41 vs. 1.62±2.55 cop/uL [log]; p=0.125). Anti-HPV antibodies ([IQR: 0-0] vs. 7.63 nm [IQR: 3.46-19.7]; p=0.0001) and seroconversion rate (8.2% vs. 96.7% [p=0.0001]) were increased at 7 versus 0 months. There were no severe vaccine-related adverse reactions; injection-site pain was reported by around half of participants. HR-HPV infection in anus was solely associated with concomitant cervix infection (HR 5.027; 95% CI: 1.009-25.042). Conclusions: nHPV vaccine in adult WLHIV is immunogenic and safe.

A regional modern river-sand geochemical mapping study in the majority of the Timor-Leste territory, including the research area, has not been previously reported. This study demonstrated the potential of modern river sand geochemical mapping as an effective method for lithological mapping, particularly in areas that face challenges in conducting efficient geological fieldwork and have limited geological information. A total of 53 modern river sand samples were collected and analyzed. Before examining the samples using wavelength-dispersive X-ray fluorescence for ten major elements, the loss-on-ignition method was employed. In the Clerec drainage basin, SiO2, CaO, and K2O showed positive correlations, and CaO was positively correlated with MnO. Similarly, in the Sahe River catchment, a positive relationship was observed between CaO, MnO, and TiO2. These findings suggested the presence of quartz, manganese, secondary K-bearing minerals, and secondary Ti-bearing minerals in carbonate rocks that have undergone silicification and other alteration processes. The principal component analysis results corroborated the SiO2/Al2O3 and K2O/Na2O ratios and the ICV findings. PC1 was related to the variations in Ca-poor and Ca-rich rocks; PC2 indicated notable inputs from SiO2-rich and SiO2-poor rocks; and PC3 revealed the possibility of contributions from secondary mineral assemblages related to silicification and low-grade metamorphic processes.

Severe COVID-19 alters the biochemical and morphological characteristics of blood cells in a wide variety of ways. To date, however, the vast majority of research has been devoted to the study of leukocytes, while erythrocyte morphological changes have received significantly less attention. The purpose of this research was to identify erythrocyte types that were unique to COVID-19, compare the number of different poikilocyte types, and measure erythrocyte sizes to provide data on size dispersion. Red blood cells obtained from 6 control donors (800-2200 cells for each donor) and 5 COVID-19 patients (800-1900 cells for each patient) were examined using low voltage scanning electron microscopy. We did not discover any forms of poikilocytes that would be unique to COVID-19. Among COVID-19 patients, we observed an increase in the number of acanthocytes (p=0.01) and a decrease in the number of spherocytes (p=0.03). In addition, our research demonstrates that COVID-19 causes an increase in the median (p=0.004) and interquartile range (p=0.009) when assessing erythrocyte size.

A fluorescent probe, N'-((3-methyl-5-oxo-1-phenyl-4, 5-dihydro-1H-pyrazol-4-yl) methylene)-2-oxo-2H-chromene-3-carbohydrazide (MPMC), was synthesized and characterized. Characterizations of the synthetic MPMC were conducted by proton nuclear magnetic resonance (1HNMR) spectroscopy and carbon-13 nuclear magnetic resonance spectroscopy (13C NMR). The fluorescence emission behaviors of probe MPMC towards diverse metal ions were detected and the probe exhibited high sensitivity and selectivity towards Cu2+ over other metal ions via quenching of its fluorescence. Furthermore, the existence of other metal actions made no difference on the fluorescence intensity of the MPMC-Cu2+ system apparently, that is, MPMC displayed a good anti-interference ability. Job’s plot of MPMC and copper ions indicated the detection limit was 15.16 nM (R2=0.9612) for the assayed actions, with a stoichiometric ratio of 1:1 for MPMC and Cu2+. Additionally, the color of MPMC probe solution changed from nearly colorless to yellow in the presence of Cu2+ in visible light, which the color change could be observed by the naked eye. Similarly, the color resolved bright yellow into blue in ultraviolet light. Also reusability studies indicated that MPMC probe was reusable. The pH effect of probe MPMC to Cu2+ had a broad range of pH detection 4.0 to 11.0. The response time of MPMC probe for determining Cu2+ was within 1 min. The recognition of Cu2+ by MPMC performed on pre-treated paper under sunlight and UV light both had a distinct colour change. Thus, the solid-state method for detecting Cu2+ with the naked-eye, was both economical and convenient.

This article presents a study conducted within a wind tunnel to enhance understanding of the excitation mechanism of stay cable vibration under arid conditions. Numerous wind tunnel tests were meticulously analyzed. Initially, the vibration of the stay cable was measured under steady flow conditions at a flow angle of 45 degrees and an inclination of 25 degrees, while varying wind velocities were applied. Additionally, an investigation into the flow field surrounding the stay cable was conducted in both vertical and horizontal directions. By utilizing two hot wire anemometers in the cable wake, an extensive database of flow field measurements was obtained. The experimental results revealed that the vibration characteristics of the stay cable under the arid conditions considered in this study aligned with findings reported in existing literature. Notably, a deeper comprehension of the excitation mechanism of a stay cable in a dry state was attained. This mechanism is closely associated with the inhibition of Karman vortices and the development of low-frequency vortices. At low wind speeds, Karman vortices predominated, resulting in small-amplitude vibrations. However, as the wind speed increased, the influence of Karman vortices diminished progressively, while the low-frequency vortices grew stronger. These low-frequency vortices exhibited high energy and a significant correlation with shedding along the stay cable, thereby inducing cable vibration in a dry environment.

To accomplish IMO's emissions reduction targets, the Chinese government has established emission control areas and implemented strict sulfur limitation policies. Faced with the downturn in the shipping industry and the challenge of insufficient supply of compliant fuel, Hong Kong and Shenzhen in China have implemented different low-sulfur fuel subsidy policies. Therefore, it is particularly important to study the air pollution control mechanism considering low sulfur fuel subsidy policy. Firstly, the non-cooperative game models considering low-sulfur fuel subsidies are constructed. Secondly, the mechanisms of various factors affecting port pricing, throughput and profit are analyzed. Then, a case study is conducted by using AIS data of container ships in Shanghai Port and Ningbo Zhoushan Port. The study reveals that whether the container service price of the leader port increases or decreases, the follower port always take corresponding follow-up measures. In both sequential and simultaneous game, the profit difference of the leader port is positively related to the subsidy ratio of the port’s own and negatively related to the coefficient of the competitor's subsidy. In conclusion, the low-sulfur fuel subsidy policy has a significant positive impact on the step-by-step implementation of more stringent pollution reduction policies in port waters.

This paper presents a proposal for a non-isolated bidirectional converter (NIBC) controlled by a deep neural network (DNN) to enable vehicle-to-vehicle (V2V) and vehicle-to-grid (V2G) charging, which contributes to the development of more efficient and sustainable transportation and energy systems. The DNN controller manages power flow in both directions, making it possible to charge electric vehicles (EVs) and discharge power from EVs to the grid with improved efficiency and performance compared to traditional control methods. The non-isolated topology used in this proposal offers several benefits, including reduced cost, smaller size, and higher efficiency. To train the DNN controller, a large dataset of simulations was used, and the results were validated with a hardware setup. The real-time performance of the DNN controller was compared to a proportional-integral (PI) based controller through simulated results. The findings of the study show that the DNN controller outperforms traditional PI controllers.

We explored the outcomes of germline BRCA1/2 pathogenic/likely pathogenic variants (PVs/LPVs) in the endocrine-sensitive disease treated with first line standard of care cyclin-dependent kinase 4/6 (CDK4/6) inhibitors. Three studies retrospectively showed a reduction in overall survival (OS) and progression free survival (PFS) in gBRCA1/2m patients compared to both germinal BRCA1/2 wild type (gBRCA1/2wt) and to the untested population. Regarding the efficacy of PI3K inhibitors, there are no subgroup or biomarker analyses in which germinal BRCA status was explored. However, the biological interactions between the PIK3CA/AKT/mTOR pathway and BRCA1/2 at a molecular level could help us to understand the activity of these drugs when used to treat BC in BRCA1/2 PVs/LPVs carriers. The efficacy of trastuzumab deruxtecan (T-DXd), an antibody-drug conjugate (ADC) targeting HER2 for HER2-low and HER2-positive (HER2+) BC, has been increasingly described. Unfortunately, data on T-DXd in HER2+ or HER2-low metastatic BC harboring germinal BRCA1/2 PVs/LPVs is lacking. Including germinal BRCA1/2 status in the subgroup analysis of the registration trials of this ADC would be of great interest, especially in the phase III trial DESTINY-breast04. This trial enrolled patients with HER2-negative (HER2-) and both HR+ and HR- metastatic disease, which can now be categorized as HER2-low. The HER2-low subgroup includes tumors that were previously classified as triple negative, so it is highly likely that some women were germline BRCA1/2 PVs/LPVs carriers and this data was not reported. Germline BRCA1/2 status will be available for a higher number of individuals with BC in the near future and data on the prognostic and predictive role of these PVs/LPVs is needed in order to choose the best treatment options.

The Direction-of-Arrival (DoA) estimation methods are highly versatile and find extensive applications in satellite communication. The DoA methods are employed across a range of orbits, from Low Earth Orbits (LEO) to Geostationary Earth Orbits (GEO). They serve multiple applications, including altitude determination, geolocation and estimation accuracy, target localization, and relative and collaborative positioning. This paper presents a novel approach for modeling the DoA angle using a closed-form expression, incorporating the boresight angle and satellite and Earth station position data. The method uses the geographic coordinate system in the satellite communication system, precisely the latitude and longitude of the Earth station and altitude parameters of the satellite stations, to calculate the Earth station’s elevation angle and accurately model the DoA angle. Furthermore, this paper performs a comprehensive comparative analysis of various DoA methods to gain deeper insights into the performance of DoA estimation in multi-antenna systems operating under spatially correlated channels. Accordingly, this paper evaluates DoA estimation performance using root-mean-square-error (RMSE) statistics for uplink and downlink conditions through extensive Monte Carlo simulations. The simulation’s effectiveness is validated against the Cramer-Rao Bound (CRB) performance metric for the Additive white Gaussian noise (AWGN) case. (i.e., thermal noise). The simulation results demonstrate improved RMSE performance in satellite systems by incorporating spatial correlation into the system model.

Hydro generator sets serve as the peak and frequency regulation of the power system,and play a very important role in maintaining system stability and improving power quality.Based on the internal characteristics model of a specific type of hydro generator,this paper constructs a hydroelectric coupling model for hydropower units,studies the influence of the regulation system of hydropower units on low-frequency oscillations under different load conditions,and adopts variable speed reaching law and fuzzy sliding mode control strategy to improve the regulation quality of the system and ensure the stable operation of the units.Results of simulation and water turbine set under different load conditions show that varible speed reaching law can effectively improve the power-angle oscillation behavior of the hydropower set and suppress the occurrence of low-frequency oscillations of the system when the system is subject to power disturbance,which provide a new theoretical basis and solution for the vibration analysis and control optimization of hydraulic turbine units.

An extended classification of active RC- and RLC- filters with Sallen-Key architectures, including those created in the last three years, is proposed. This makes it possible to formulate new design directions for an extended family of active RC- and RLC- Sallen-Key filters (PF, LPF, HPF, RF) for the tasks of high-speed and ultra-fast analog-to-digital signal conversion.

Ensuring a protection scheme in DC distribution is more difficult to achieve against pole-to-ground fault than in AC distribution system because of the absence of zero crossing points and low line impedance. To complement the major obstacle of limiting the fault current, several compositions have been proposed related to mechanical switching and solid-state switching. Among them, solid-state circuit breakers(SSCBs) are considered a possible solution to limit fast fault current. However, they may cause problems in circuit complexity, reliability and cost-related troubles due to the use of multiple power semiconductor devices and additional circuit configuration to commutate current. This paper proposes the SSCB with a coupled inductor(SSCB-CI) which has symmetrical configuration. The circuit is comprised of passive components like commutation capacitors, a CI and damping resistors. Thus, proposed SSCB-CI offers the advantages of simple circuit configuration and fewer utilized power semiconductor devices than another typical SSCBs in LVDC microgrid. For analysis, six operation states are described for the voltage across main switches and fault current. The effectiveness of the SSCB-CI against a short-circuit fault is proved via simulation and experimental results in a lab-scale prototype.

A high proportion of dogs and cats are fearful during veterinary visits, which in some cases may escalate into aggression. Here, we discuss factors that contribute to negative emotions in a veterinary setting and how these can be addressed. The set-up of the waiting area (e.g. spatial dividers; elevated places for cat carriers), tailoring the examination and the treatment to the individual, considerate handling (minimal restraint when possible, avoiding leaning over or cornering animals) and offering high-value food or toys throughout the visit can promote security and, ideally, positive associations. Desensitisation and counterconditioning are highly recommended both to prevent and address existing negative emotions. Some negative experiences such as short-term pain from injections can be minimised by using tactile and cognitive distractions. Preemptive analgesia is recommended for known painful procedures. Recommendations for handling fearful animals to minimise aggressive responses are discussed. However, anxiolytics or sedation should be used whenever there is a risk of traumatising an animal or for safety reasons. Stress-reducing measures can decrease stress and fear in patients and consequently their owners – thus strengthening the relationship with the clients as well as increasing the professional satisfaction of veterinary staff.

Background: Low-level physical activity (PA) among Chronic Low Back Pain (cLBP) is associated with various biopsychosocial factors. This research aimed to study the predictors of PA behavior among cLBP patients. Methods: In the present study 300 eligible patients with cLBP who referred to comprehensive health service centers in the Shahid Beheshti University of Medical Sciences (SBUMS) in Tehran, Iran were random selected.To diagnose the predictors of PA behavior, all the Theory of Reasoned Action (TRA) constructs were examined as risk factors to see if they influence on the probability of PA behavior occurrence and were interpreted through odds ratio (OR). SPSS version 19 was used to analyze the data. Results: Totally 280 cLBP patients with mean age of 57.07 ±13.09 years old participated in the study. This study showed that motivation to comply significant predictor the cLBP patients for subjective norm OR (%95CI): 2.095(0.116-2.792), p-value<0.001), intention was significant predictor for perform the PA behavior OR (%95CI): 1.431(0.138-1.538), p-value <0.001), behavior beliefs could predictor for attitude OR (%95CI): 1.276(0.106-1.355), p-value= 0.002). attitude, normative beliefs, subjective norm ,and evaluation outcome behavior could predictors the cLBP patients for intention to perform the PA behavior OR (%95CI): 1.188(0.032-1.312), p-value<0.001)., OR (%95CI): 1.158(0.076-2.208), p-value=0.003) ., OR (%95CI): 1.104(0.076-1.128), p-value<0.001) ., OR (%95CI): 0.814(0.301-1.440), p-value=0.007). Conclusions: This study showed that the cLBP patients who were normative beliefs and evaluation regarding PA behavior could effect on the intention to engage in greater PA than those via other constructs (attitude and subjective norm). This study showed that the cLBP patients who were normative beliefs and evaluation regarding PA behavior could effect on the intention to engage in greater PA than those via other constructs (attitude and subjective norm). This study showed that the cLBP patients who were normative beliefs and evaluation regarding PA behavior could effect on the intention to engage in greater PA than those via other constructs (attitude and subjective norm).

Green infrastructure systems are often overdesigned. This may be a byproduct of static sizing (e.g., accounting for a design storm’s runoff volume but not exfiltration rates) or may be deliberate (e.g., buffering against performance loss through time). Regardless, overdesign may compromise plants’ access to water in systems where soil pits are embedded in infiltration beds. It could raise the storm size required for water to reach soil pits, reducing water availability between storms, which could ultimately induce plant physiological stress. This study investigated the hydrological dynamics and water relations of a tree trench system suspected to have been overbuilt and identified factors contributing to, compounding, and mitigating the risk of plant stress. Results provided strong evidence that the abovementioned processes played out. Water in the infiltration bed reached soil pits only once in three years, with that event occurring during a hydrant release. Moreover, minimal water was retained in the soil pit during the event due to the hydraulic properties of the soil media. Through a growing season, one of the two tree types frequently experienced water stress, while the other did so only rarely. These contrasting responses can likely be attributed to roots either being largely confined to the soil pits or reaching a deeper water source. Implications of these results for green infrastructure design are considered.

The solution of structural problems with nonlinear material behaviour in a model order reduction framework is investigated in this paper. In such a framework, greedy algorithms or adaptive strategies are interesting as they adjust the reduced order basis (ROB) to the problem of interest. However, these greedy strategies may lead to an excessive increase in the size of the reduced basis, i.e. the solution is no more represented in its optimal low-dimensional expansion. Here, an optimised strategy is proposed to maintain, at each step of the greedy algorithm, the lowest dimension of the PGD basis using a randomised SVD algorithm. Comparing to conventional approaches such as Gram-Schmidt orthonormalisation or deterministic SVD, it is shown to be very efficient both in terms of numerical cost and optimality of the reduced basis. Examples with different mesh densities are investigated to demonstrate the numerical efficiency of the presented method.

Thermal stresses belong to the leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature properties of asphalt mixtures, three point bending and uniaxial tensile creep tests were applied and the master curves of stiffness modulus were analyzed. On the basis of creep test results, rheological parameters describing elastic and viscous properties of the asphalt mixtures were determined. Thermal stresses were calculated and compared to tensile strength of the material to obtain the failure temperature of the analyzed asphalt mixtures. It was noted that lower strain values of creep curves were obtained for the Tensile Creep Test (TCT) than for the Bending Beam Creep Test (BBCT), especially at lower temperatures. Results of thermal stress calculations indicated that higher reliability was obtained for the viscoelastic Monismith method based on the TCT results than for the simple quasi-elastic solution of Hills and Brien. The highest agreement with the TSRST results was also obtained for the Monismith method based on the TCT results. No clear relationships were noted between the predicted failure temperature and different methods of thermal stress calculations.

As a result of the cancer immunotherapy revolution hundreds of clinical trials of the newly approved immunotherapies are now under way to improve responses. Not unexpectedly, the 2018 Nobel Prize in Physiology or Medicine was awarded to James P. Allison and Tasuku Honjo for their development of cancer therapy by blockade of co-inhibitory signals. While success stories of terminal cancer patients achieving complete remissions are accumulating, not enough research has been done into the risks of the new therapies. Since the use of immunotherapy is becoming more common, and is expected to develop into first- and second-line treatments, immunotoxicity and autoimmunity are emerging as the nemesis of immunotherapy. Immune-related adverse events (IrAEs) could affect any tissue, their incidence may reach up to 90% of patients and toxicity is dose-dependent. While the combination of two immune checkpoint inhibitors (ICIs) increased efficacy, the incidence of severe adverse events was also increased. Apparently, ICIs cannot be restricted to the targeted anti-tumor T cell population. The long lasting objective of cancer regression can only be achieved by paying a price: tolerance to healthy self tissues is compromised. In the face of an ipilimumab induced pan-lymphocytic activation, a therapeutic paradigm shift is required. The task is not desperately trying to put the genie back in the bottle by immune suppressive treatments, but instead harnessing the autoimmune forces by an off label low-dose combined anti-CTLA-4 and anti-PD1 antibody blockade, which is supplemented with conventional interleukin-2 stimulation and hyperthermia. The proof-of-principle of the low-dose-combination therapy was demonstrated in a heavily pre-treated triple negative breast cancer (TNBC) patient with far advanced pulmonary metastases and severe shortness of breath, who had exhausted all conventional treatment. Her pulmonary metastases went into complete remission with transient WHO I-II diarrhea and skin rash. She lived for 27 months after starting the low-dose-combination therapy. She had recurrence as a sternal mass and pleural metastases up to 3 cm. Since the low-dose-combination protocol consists only of approved drugs and treatments, this exceptional response should instigate further research efforts.

We have successfully measured amyloid beta (Aβ) (1-40) protein added in human serum by a NiCr strain gauge cantilever biosensor immobilized with liposomes incorporating cholesterol. Importantly, we investigated the effect of incorporation of cholesterol in the liposome in order to suppress the interaction between the liposome and many different proteins included in human serum. It was revealed that incorporating cholesterol suppresses the interaction between the proteins other than Aβ in human serum and the liposome. Finally, we detected Aβ(1-40) in human serum with typical chronological behaviors due to Aβ aggregation and fibrillization. Furthermore, as a digital low-pass filtering procedure could reduce external noises, the cantilever sensor immobilized with liposome incorporating cholesterol can detect low-concentrated Aβ in human serum.

The central aim of this paper is to present the Green Web Meter software which is designed to support the measurement of digital sustainability performance of websites and web apps, as well as providing sound based analytic tools for improving their overall quality. We analyzed scientific literature and specifically selected three quality assessment models (E-S Qual, Sitequal, Webqual 4.0) which we used as a starting point for identifying the most crucial aspects for the monitoring activities. A consistent set of Key Performance Indicators (KPIs) suitable for automated tracking has been provided. We finally developed model-based software able to deliver solutions for real-time website performance analysis and reports. We structured the model to offer accurate references for digital sustainability reporting by aggregating the KPIs into an Environmental, Social, and Governance (ESG) framework and computing a comprehensive score for its pillars.

Graphene was synthesized through a two-step pyrolysis method using waste candlenut (Aleurites moluccanus) shells as the precursor. Cerium (Ce)/graphene composites were prepared via an impregnation technique. The resulting graphene and Ce/graphene were characterized using various analytical methods, including Scanning Electron Microscopy with Energy-Dispersive Spectroscopy (SEM-EDS), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscopy (TEM), Thermo Gravimetric Analysis (TGA), Fourier Transform Infrared (FTIR) spectroscopy, Cyclic Voltammetry (CV), and Linear Sweep Voltammetry (LSV). The bio-carbon produced predominantly exhibited a graphene structure with flat carbon morphology and an interlayer distance of 0.33 nm. This structural information is supported by XRD data, which shows a broad and weak peak at 2θ = 26° corresponding to the C (002) plane, indicative of graphene presence. FTIR, XPS, and Raman spectroscopy further confirmed the presence of graphene through the detection of Csp2 aromatic bonds and the characteristic D, G, and 2D peaks. Notably, the performance of cerium can be enhanced by the incorporation of graphene, attributed to the large surface area and chemical interactions between Ce and graphene. Consequently, candlenut-derived graphene shows potential as a supportive material for modifying the properties of cerium, thereby opening avenues for various advanced applications, such as sustainable and high-performance energy storage systems.

While the simple model of the total atmospheric carbon sink effect as a linear function of concentration has provided excellent prediction results, several problems remained to be investigated and solved. The most obvious open issue is the correct treatment of land use change emssions. It turns out that the model improves by mostly neglecting them after 1959. This effectively implies that land use change emissions have been constant and small since then. The key investigation starts with the observation, that the total carbon sink has a short term component which be explained by temperature changes commonly known as El Nin˜o. The apparent paradox is analysed and explained, why contrary to the short term changes no temperature caused trend can be detected in the model, despite the fact that several contributing processes exhibit temperature dependency. The result of this analysis leads to the model extension, where the total effect of sinks and natural emissions are a linear function of concentration and temperature. This model not only explains current measurements but also paleo climate from ice-core time series.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

The main source of electricity worldwide stems from fossil fuels, contributing to air pollution, global warming, and associated adverse effects. This study explores wind energy as a potential alternative. Nevertheless, the variable nature of wind introduces uncertainty in its reliability. Thus, it is necessary to identify an appropriate machine learning model capable of reliably forecasting wind speed under various environmental conditions. This research compares the effectiveness of artificial neural networks (ANN) and convolutional neural networks (CNN) in predicting wind speed across three locations in South Africa, characterised by different weather patterns. Empirical results show that CNN outperforms ANN in accurately forecasting wind speed under different weather conditions. This superiority is likely due to the inherent architectural attributes of CNNs, including feature extraction capabilities, spatial hierarchy learning, and resilience to spatial variability. These results could be useful to decision-makers in the energy sector.

The impact of long-term soil and crop management practices on soil biological and chemical properties in oilseed brassica-based production systems were deliberated for holistic soil health improvement in the present study. Different tillage, crop residue re-cycling and cropping systems were studied for 5-years in 0-15 and 15-30 cm soil profiles. No-till permanent beds with crop residue (PB+R) noticeably improved soil organic carbon (SOC), microbial biomass carbon (MBC), enzymes [dehydrogenase (DHA) and alkaline phosphatase (AlP)], nitrogen fractions (available, nitrate and total), and available phosphorus and potassium content in both the soil layers compared to conventional tillage without crop residues. Though, the plow soil layer (0-15 cm) showed higher concentration of soil carbon, enzymes, N fractions and available P than in the sub soil (15-30 cm). The dynamic soil biological and chemical properties were also varied with the crop stage, and recorded higher MBC at 30 days, SOC and enzymatic activities at 60 days, and N fractions and available P and K at harvest of mustard crop. Green gram-mustard rotation showed higher values of biological and chemical parameters. Thus, the legume-based mustard crop rotation following no-till permanent beds and residue re-cycling found holistic in improving soil health, and nutrient cycling.

Hybrid materials derived adsorbents have showed a great applicable efficiency in various fields including industrial uses and environmental remediation. Herein, the zinc oxide nanoparticles anchored carbon (ZnO-C) is fabricated and utilized for wastewater treatment by adsorption of Zn(II), Cd(II), Co(II) and Mn(II). The surface and structural characteristics are examined by TEM, SEM, XRD, FTIR, EDS and BET surface area. The Kinetics and equilibrium investigations are applied to optimize the adsorptive removal of Zn(II), Cd(II), Co(II) and Mn(II) onto ZnO-C. Results indicated formation of ZnO-C in crystalline spherical granules with nano-size between 29.3 and 48.8 nm. In addition, the spherical granules are gathered to form clusters. The FTIR indicated that the ZnO-C surface is rich with OH groups and ZnO. The adsorption capacity is reported as 212, 209, 200 and 230 mg/L for Zn(II), Cd(II), Co(II) and Mn(II) respectively. The optimum condition for maximum adsorption were pH between 5 and 6, contact time of 180 min and adsorbent dose of 0.1 g/L. The adsorptive removal data modeling for uptake of Zn(II), Cd(II), Co(II) and Mn(II) onto ZnO-C showed agreement with the assumption of pseudo 2nd order kinetic model and Freundlich isotherm suggesting fast adsorption rate and multilayer mechanism. The achieved adsorption capacity using the prepared ZnO-C is more effective compared to ZnO, carbon, Fe3O4 and Fe3O4-C. Real wastewater samples are applied including valley water, industrial wastewater and rain wastewater and evaluated for applicable uptake of Zn(II), Cd(II), Co(II) and Mn(II) using ZnO-C and Fe3O4-C with high efficiency.

Matter grows and self-assembles to produce complex structures such as virus capsids, carbon fullerenes, proteins, glasses, etc. Due to its complexity, performing pen-and-paper calculations to explain and describe such assemblies is cumbersome. Many years ago, Richard Kerner presented a pen-and-paper path integral approach to understand self-organized matter. Although successfully addressed many important problems including the yield of fullerene formation, the glass transition temperature of doped chalcogenide glasses, the fraction of boroxol rings in B2O3 glasses, the first theoretical explanation for the empirical recipe of window and Pyrex glass and the understanding of virus capsid self-assembly, still is not the primary choice when tackling similar problems. The reason lies in the fact that it diverges from mainstream approaches based on the energy landscape paradigm and non-equilibrium thermodynamics. In this context, a critical review is presented, demonstrating that the Richard Kerner method is, in fact, a clever way to identify relevant configurations. Its equations are simplified, common physical sense versions to those found in the energy landscape kinetic equations. Subsequently, the utilization of equilibrium Boltzmann factors in the transition Markov chain probabilities is analyzed within the context of local two-level energy landscape models kinetics. This analysis demonstrates that their use remains valid when the local energy barrier between reaction coordinate states is small compared to the thermal energy. This finding places the Richard Kerner model on par with other more sophisticated methods and, hopefully, will promote its adoption as an initial and useful choice for describing the self-agglomeration of matter.

We propose a silviculture with a purely biological logic that takes soil into account. The article is divided into three parts: 1) presentation of the issue in the context of biodiversity and forest pro-tection; 2) impact of the soil functioning on forestry; 3) possible implementation of soil functioning in forestry practice, to support and protect a non-or minimally anthropized evolution of the forest. The first chapter illustrates the importance of the forest for the future of the planet and our human species, referring to recently published works on the topic of climate warming and biodiversity. The second illustrates the aspects that link soil dynamics to the silvogenetic cycle, focusing on the humipedon (organic and organo-mineral surface horizons, approximately the first 30 cm of forest soil), and more significant carbon storage in old forests since up to 2/3 is found in the soil. In the third chapter we consider the possibility of lengthening the forestry cycle, to allow the return of nutrients to the soil. Theoretical graphs and distribution models of the number of trees as a func-tion of diameter and age are reported, with examples of logging in uneven Alpine forests, with reference to Swiss fir-beech forests published on the Pro-Silva website.

This study evaluated gas mixtures of carbon dioxide (CO2) associated with nitrogen (N2) as al-ternatives to the use of CO2 in two phases to improve the welfare of broiler chickens at slaugh-ter. Broilers were exposed to one of three treatments: 40C90C (1st phase: <40% CO2 for 2 min; 2nd phase: >90% CO2 and <2% O2 for 2 min, n=92), 40C60N (40% CO2, 60% N2 and <2% O2 for 4 min, n=79), or 20C80N (20% CO2, 80% N2 and <2% O2 for 4 min, n=72). The time to onset of loss of consciousness (LOC) and death was assessed by brain activity (EEG) and behaviour. Behaviour also allowed characterisation of the aversive response to the treatments. Exposure to 40C60N and 20C80N induced LOC faster (19 s [14 – 30 s] and 21 s [16 – 37 s], respectively) but also with less inter-individual variability compared to 40C90C (53 s [26 – 156 s], P < 0.001) and birds took less time to die (40C60N: 64 s [43 – 108 s]; 20C80N: 70 s [45 – 88 s]; 40C90C: 177 s [89 – 212 s], P < 0.001). The 40C90C birds not only experienced more aversion during induction to LOC but are at risk of remaining conscious when the CO2 concentration is increased in the 2nd phase. From an animal welfare point of view, 40C60N provided the highest welfare, followed by 20C80N and 40C90C.

This review delves into the intricate relationship between folate (Vitamin B9) intake, especially its synthetic form, folic acid, and its implications on health and disease. While folate plays a pivotal role in the one-carbon cycle, essential for DNA synthesis, repair, and methylation, concerns arise from its excessive intake. The literature underscores potential deleterious effects, such as an increased risk of carcinogenesis, disturbances in DNA methylation, and impacts on embryogenesis, pregnancy outcomes, neurodevelopment, and disease risk. Notably, these consequences stretch beyond the immediate effects, potentially influencing future generations through epigenetic reprogramming. We probe into the molecular mechanisms underlying these effects, including accumulation of unmetabolized folic acid, Vitamin B12 dependent mechanisms, altered one carbon metabolism, altered methylation patterns, and interactions with critical receptors and signaling pathways. Furthermore, we emphasize differences in the effects and mechanisms mediated by folic acid compared to natural folate. Given the widespread folic acid supplementation, it is imperative to further research its optimal intake levels, and the molecular pathways impacted by its excessive intake, ensuring the health and well-being of the global population.

In this review, we focus on a small section of the extensive literature that deals with the materials containing pristine defective CNs and those incorporated in the hybrid materials. We will discuss only those topics that focus on structural defects related to the introduction of perturbation into the surface topology of a nanostructure. We focus mainly on the method using microwave (MW) irradiation, which is a powerful tool for synthesizing and modifying carbon-based solid materials. In addition, the simplicity of the technique, economy, and the possibility of conducting the reaction in solvents and solid phase, in the presence of components of different chemical nature, allows use in various combinations. In this review, we will emphasize the advantages of synthesis using MW-assisted heating and indicate the influence of the structure of the obtained materials on their physical and chemical properties. We will also highlight the role of the occurrence of defects in the carbon material and the implication in designing their properties and applications.

When attempting to quantify future harms caused by carbon emissions and to set appropriate energy policies, it has been argued that the most important metric is the number of human deaths caused by climate change. Several studies have attempted to overcome the uncertainties associated with such forecasting. In this article, approaches to estimating future human deaths tolls from climate change are compared and synthesized, and implications for energy policy are considered. Several studies are consistent with the “1000-ton rule,” according to which a future person is killed every time 1000 tons of fossil carbon are burned (order-of-magnitude estimate). If warming reaches or exceeds 2°C this century, mainly richer humans will be responsible for killing roughly 1 billion mainly poorer humans through anthropogenic global warming. Such mass manslaughter is clearly unacceptable. On this basis, relatively aggressive energy policies are summarized that would enable immediate and substantive decreases to carbon emissions. The limitations to such calculations are outlined and future work is recommended to accelerate the decarbonization of the global economy while minimizing the number of sacrificed human lives.

Thermal processing of Zr-loaded ion-exchangers is a facile route to synthetize (ZrO2, ZrC)@C composites. The chemical character of the functional groups in the cation exchanger is an essential factor in the composition and properties of the (ZrO2, ZrC)@C composites. In the present paper furnace and RF-thermal plasma processing of ZrOCl2 loaded thiourea-functionalized styrene-divinylbenzene copolymer was investigated that led to various composites containing ZrO2 and ZrC. Depending on the synthesis conditions, different ZrO2@C composites were formed between 1000 and 1400 °C in 2 h, whereas the composite containing ZrC was created at 1400 °C in 8 h. The ratio of ZrO2/ZrC, the prevailing ZrO2 modifications, and the crystallite sizes strongly depend on the synthesis conditions. The ZrC-containing composites formed only at 1400 °C in 8 hours and by the plasma treatment of the ZrO2@C sample prepared in the furnace, resulting in 8 and 16% ZrC content, with 44 and 41 nm ZrC crystallite sizes, respectively. The ZrO2-containing composites (tetragonal, monoclinic, and cubic modifications with 65–88 nm ZrO2 crystallite sizes and 15–43 m2/g BET surface areas, depending on the carbonization temperature) formed in a tube furnace between 1000 and 1400 °C in 2 h. The tube furnace–prepared sample formed at 1400 °C in 8 h contained ZrC, ZrO2 modifications, and amorphous carbon, whereas the plasma-treated sample contained ZrC, ZrO2 modifications, and graphite. All ZrO2@C composites had both amorphous carbon and graphite, and their ratio is temperature-dependent. The carbonaceous compounds of the prepared composites were characterized by Raman spectroscopy, with analysis of the G and D band intensities. XPS studies showed the surface oxidation of ZrC.

This work is related to the environmental toxicology risk assessment and evaluation of possible transformation of carbon-based nanomaterials (CNMs) after the contact with marine microalgae. The materials used in the study represent common and widely applied multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO). The toxicity was evaluated as growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species generation changes. The measurement was performed with flow cytometry after 3, 24, 96 h, and 7 days. Biotransformation of nanomaterials were evaluated after 7 days of microalgae cultivation with CNMs by FTIR and Raman spectroscopy. The calculated toxic level (EC50 in mg/L, 96 h) of ued CNMs reduced in the following order: CNTs (18.98) &gt; GrO (76.77) &gt; Gr (159.40) &gt; C60 (414.0). Oxidative stress and membrane depolarization was the main toxic action of CNTs and GrO. At the same time, Gr and C60 decreased the toxic action with time and had no negative impact on microalgae even at concentration of 125 mg/L. Moreover, C60 and Gr after seven days of the contact with microalgae cells obtained structural deformations.

To study the strengthening effect on recycled concrete columns by carbon fiber composite materials (CFRP) under different levels of seismic damage, four column specimens were designed for pseudo-static tests. The four specimens were respectively non-destructive without strengthening (prototype), non-destructive strengthening, medium seismic damage strengthening and severe seismic damage strengthening, according to the replacement rate of recycled aggregates and the level of seismic damage. The characteristics of the deformation damage and seismic performance indicators of each specimen were compared and analyzed. A decrease was observed in the initial stiffness of the seismically damaged recycled concrete column specimens strengthened with CFRP, while the ductility, peak bearing capacity and energy dissipation capacity of the specimens were improved. On the other hand, with the reduction of seismic damage and the increase of recycled aggregate replacement rate, the ductility and energy dissipation capacity of the reinforced seismic damaged recycled concrete column specimens were enhanced to different levels. In particular, the cumulative energy consumption of the strengthened specimens under medium seismic damage increased most significantly by 32.5%. In general, the hysteretic curves of the strengthened specimens were full, and the average ductility coefficients were 4.1–6.8. CFRP strengthening was more effective in restoring and enhancing the performance of the recycled concrete column specimens with medium and lower seismic damage levels (displacement ratio ≤ 3%).

Near-neutral pH and low redox potentials (EH) are considered favorable conditions for radionuclides immobilization in deep repository systems in clay geological formations. Cigeo is a future Industrial Centre for Geological Disposal for Nuclear Waste (NW) for high-level and intermediate level long-lived radioactive waste, to be built in France, at 500 m depth within the Callovo-Oxfordian clay formation. Deep knowledge of the mechanisms and kinetics of corrosion occurring at the external surface of tubings made of API 5L X65 carbon steel (CS-X65) in contact with COx pore water, is essential for a reversible NW management of the Cigeo site. By using robust handmade electrodes and electrochemical and gravimetric techniques, this work aimed to determine the corrosion phenomenology and kinetics of CS-X65 in contact with COx pore water flowing continuously through a Multi-Parameter Probe (MPP) device, placed at 500 m depth, for more than 180 days. It also aimed at demonstrating the reliability and the robustness of the measurement methodology for the corrosion evaluation of the metallic liner of the future nuclear waste disposal site. Two iron oxidants were encountered, oxygen, who was depleted, and proton, who was accompanied by hydrogen sulfide. Corrosion mechanisms and kinetics were well established for two CS-X65, electrochemically perturbed and not. The corrosion thickness loss rates stand between 0.016 and 0.032 mm/y.

The emission of black carbon (BC) particles, which cause atmospheric warming by affecting radiation budget in the atmosphere, is the result of an incomplete combustion process of organic materials. The recent wildfire event during the summer 2019-2020 in South-Eastern Australia was unprecedented in scale. The wildfires lasted for nearly 3 months over large areas of the two most populated states of New South Wales and Victoria. This study on the emission and dispersion of BC emitted from the biomass burnings of the wildfires using the Weather Research Forecast – Chemistry (WRF-Chem) model is aimed to determine the extent of the BC spatial dispersion and ground concentration distribution and the effect of BC on air quality and radiative transfer at the top of the atmosphere, the atmosphere and on the ground. The predicted aerosol concentration and AOD are compared with the observed data from the New South Wales Department of Planning and Environment (DPE) aethalometer and air quality network and from remote sensing data. The BC concentration as predicted from WRF-Chem model is in general less than the observed data as measured from the aethalometer monitoring network, but the spatial pattern corresponds well, and the correlation is relatively high. The total BC emission into the atmosphere during the event and the effect on radiation budget were also estimated. This study shows that the summer 2019-2020 wildfires affect not only the air quality and health impact on the east coast of Australia but also short-term weather in the region via aerosol interactions with radiation and cloud.

The use of additive manufacturing in fabricating composite components has been gaining traction in the past decade. However, some issues with mechanical perfor-mance still need to be resolved. The issue of material porosity remains a pertinent one that needs more understanding to be able to determine viable solutions. Different re-searchers have examined the subject of porosity issues in AM-fabricated CFRP compo-sites. However, more research to quantitatively determine the effects of fabrication temperatures at the micro-scale is still needed. This study employed micro CT scan analysis to quantitatively compare the effects of fabrication temperatures at 230°C, 250°C, 270°C, and 290°C for CF-PA and CF-ABS composites. This followed an SEM evaluation which was used to determine the effects of the temperatures on interlayer and intralayer porosity generation. The porosity volume was related to the mechanical properties results in which it was determined how deposition temperatures affect the porosity volumes. It was also determined that semicrystalline composites are generally more affected by fabrication temperatures than amorphous composites, with the rela-tionship between porosity and mechanical properties also established. The overall po-rosity volume from the interlayer and intralayer voids was also determined, with the interlayer voids found to play a more determinant role in influencing the mechanical properties.

Lettuce is a salt-sensitive crop and has a threshold electrical conductivity of 1.3–2.0 mS cm-1 and above that is considered detrimental. As there has been very little information on the physio-logical response of different critical stages of lettuce under different salt stress (SS), the current study is focused on investigating the effects of SS on the critical physiological traits influencing the carbon assimilation in different growth stages of lettuce. The experiment was conducted in deep-water culture hydroponic system in a greenhouse condition. Four levels of sodium chloride salt treatments (EC: 20, 16, 8, and 1.8 mS cm-1) were applied. During both growth stages (day 11 (GS1) and day 19 (GS2) after salt treatment), the leaf transpiration rate, stomatal conductance, and intercellular CO2 were severely decreased. However, the carbon assimilation rate remained unchanged under SS. Similarly, the water use efficiency increased under the SS. It is concluded that the increasing SS increased stomatal and non-stomatal limiting factors during GS1 suggesting the enhanced limitation in photosynthetic activity while no such trend was observed during GS2. The decreased gm with increased SS at GS1 and GS2 suggested that SS induced the irreversible decrease of gm, which in turn can be responsible for the transient reduction in the Vcmax and Jmax during GS2. Taken together, the evidence from this research recommends that varying the SS levels can significantly affect the physiological performance of lettuce at both growth stages.

This paper presents a new implementation of a 2-box absolute flow model, enabling the calculation of CO₂ transfer between the atmosphere and a mixing reservoir representing the combined effect of the terrestrial and ocean regions. The model uses published values of anthropogenic CO₂ fossil fuel emissions (CO2ff), atmospheric CO₂ mixing ratio and nuclear weapons bomb yields, to compute atmospheric d¹³C and Δ¹⁴C time-series. The level of agreement between the calculated values and the accepted values for d¹³C is within ± 0.05 ‰, and for Δ¹⁴C is within ± 3‰, spanning 200 years. The model contains only seven internal parameters; these are varied to optimize the fit, leading to reasonable parameter values, indicating the validity of the method. In addition, the model shows how a rising CO₂ exchange influx fluctuating with surface temperature is compatible with a nett atmospheric CO₂ sink. The study demonstrates that a single CO₂ residence time applies to both the ¹⁴C bomb pulse and the anthropogenic flux, contrary to the conventional view that "bomb radiocarbon and anthropogenic CO₂ do not behave identically." [Joos 1994 Nature 370, 181–182]. It is shown that the difference in behaviour, claimed to be due to seawater chemistry, is not significant in practice since fluctuating bulk carbon dominates fluctuating isotopic ratio. A new analysis of the airborne fraction indicates that the assumption of a time-dependent exchange influx results in a similar residence time for bulk CO₂ as for ¹⁴C in the nuclear bomb pulse, reinforcing the view that the ¹²C, ¹³C and ¹⁴C carbon isotopic forms of CO₂ behave similarly in the carbon cycle.

Recent times have witnessed an increasing number of countries and private firms pledging carbon neutrality by mid-century. Whilst representing a significant improvement in intentions to tackle climate change, such pledges lack substance and structure. For instance, individual pledges lack coordination and aggregation among peers, while strategies and measures to achieve ambitious targets are largely absent. Moreover, current disagreements obstructing progress in international climate change negotiations further undermine the reliability of carbon neutrality objectives. Effective international policies are needed to foster aggregate mitigation ambitions and the creation of adequate supporting mechanisms. This theoretical paper describes a governance innovation aimed at overcoming such shortfalls and disagreements through a unifying yet customizable pathway towards carbon neutrality. It does so by first outlining a political governance framework based on a climate club interpretation of Article 6 of the Paris Agreement. Secondly, it proposes carbon emission mitigation effort sharing on a per capita basis to ensure efficiency, equity and political feasibility. Thirdly, this paper describes how the supply of certified mitigations of carbon emissions required to satisfy effort sharing-based demand can be assetized as carbon credits by operationalizing Article 6 as a joint certification mechanism. The resulting governance architecture for managing demand and supply of mitigations shifts efforts to tackle climate change from a ‘problem-driven’ cost approach to ‘opportunity-driven’ value creation pathways towards carbon neutrality.

An in-depth study of the failure of granular materials, which is known as a mechanism to generate defects, can reveal the facts about the origin of the imperfections such as cracks in the carbon anodes. The initiation and propagation of the cracks in the carbon anode, especially the horizontal cracks below the stub-holes, reduce the anode efficiency during the electrolysis process. In order to avoid the formation of cracks in the carbon anodes, the failure analysis of coke aggregates can be employed to determine the appropriate recipe and operating conditions. In this paper, it will be shown that a particular failure mode can be responsible for the crack generation in the carbon anodes. The second-order work criterion is employed to analyze the failure of the coke aggregate specimens and the relationships between the second-order work, the kinetic energy, and the instability of the granular material are investigated. In addition, the coke aggregates are modeled by exploiting the discrete element method (DEM) to reveal the micro-mechanical behavior of the dry coke aggregates during the compaction process. The optimal number of particles required for the failure analysis in the DEM simulations is determined. The effects of the confining pressure and the strain rate as two important compaction process parameters on the failure are studied. The results reveal that increasing the confining pressure enhances the probability of the diffusing mode of the failure in the specimen. On the other hand, the increase of strain rate augments the chance of the strain localization mode of the failure in the specimen.

The use of swine manure as a source of plant nutrients is one alternative to synthetic fertilizers. However, conventional manure application with >90% water and a low C:N ratio results in soil C loss to the atmosphere. Our hypothesis was to use biochar as a manure nutrient stabilizer that would slowly release nutrients to plants upon biochar-swine manure mixture application to soil. The objectives were to evaluate the impact of biochar-treated swine manure on soil total C, N, and plant-available macro and micronutrients in greenhouse-cultivated corn (Zea mays L.) and soybean (Glycine max (L.) Merr.). Neutral pH red oak (RO), highly alkaline autothermal corn stover (HAP), and mild acidic Fe-treated autothermal corn stover (HAPE) biomass were pyrolyzed to prepare biochars. Each biochar was surface-applied to swine manure at a 1:4 (biochar wt/manure wt) ratio to generate mixtures of manure and respective biochars (MRO, MHAP, and MHAPE). Conventional manure (M) control and manure-biochar mixtures were then applied to the soil at a recommended rate. Corn and soybean were grown under these controls and treatments (S, M, MRO, MHAP, and MHAPE) to evaluate the manure-biochar impact on soil quality, plant biomass yield, and nutrient uptake. Soil OM significantly (<0.05) increased in all manure-biochar treatments; however, no change in soil pH or N was observed under any treatment. No difference in soil ammonium between treatments was identified. There was a significant decrease in soil M3-P and soil NO₃^- for all manure-biochar treatments compared to the conventional M. However, the plant biomass nutrient concentrations were not significantly different from control manure. Moreover, an increasing trend of N and decreasing trend of P in the plant under all biochar-manure treatments than the controls were noted. This observation suggests that the presence of biochar is capable of influencing the soil N and P in such a way as not to lose those nutrients at the early growth stages of the plant. In general, no statistical difference in corn or soybean biomass yield and plant nutrient uptake for N, P, and K was observed. Interestingly, manure-biochar application to soil significantly diluted the M3-extractable soil Cu and Zn concentrations. The results attribute that manure-biochar has the potential to be a better soil amendment than conventional manure application to the soil.

The planetary wave activity in the stratosphere–mesosphere during the Arctic major Sudden Stratospheric Warming (SSW) in February 2018 is discussed on the basis of the microwave radiometer (MWR) measurements of carbon monoxide (CO) above Kharkiv, Ukraine (50.0° N, 36.3° E) and the Aura Microwave Limb Sounder (MLS) measurements of CO, temperature and geopotential heights. From the MLS data, eastward and westward migrations of wave 1/wave 2 spectral components were differentiated, to which less attention was paid in previous studies. Abrupt changes in zonal wave spectra occur with the zonal wind reversal near 10 February 2018. Eastward wave 1 and wave 2, observed before the SSW onset, disappear during the SSW event, when westward wave 1 becomes dominant. Wavelet power spectra of mesospheric CO variations show statistically significant periods in a band of 20–30 days using both MWR and MLS data. Approximately 10-day periods appear only after the SSW onset. Since the propagation of upward planetary waves is limited in the easterly zonal flow in the stratosphere after the zonal wind reversal during SSW, forced planetary waves in the mid-latitude mesosphere may exist due to the instability of the zonal flow.

Sideroflexins (SLC56 family) are highly conserved multi-spanning transmembrane proteins inserted in the inner mitochondrial membrane in eukaryotes. Few data are available on their molecular function but, since their first description, they were thought to be metabolite transporters probably required for iron utilization inside the mitochondrion. Such as numerous mitochondrial transporters, sideroflexins remain poorly characterized. The prototypic member SFXN1 has been recently identified as the previously unknown mitochondrial transporter of serine. Nevertheless, pending questions on the molecular function of sideroflexins remain unsolved, especially their link with iron metabolism. Here, we review the current knowledge on sideroflexins, their presumed mitochondrial functions and the sparse - but growing - evidence linking sideroflexins to iron homeostasis and iron-sulfur cluster biogenesis. Since an imbalance in iron homeostasis can be detrimental at the cellular and organismal levels, we also investigate the relationship between sideroflexins, iron and physiological disorders. Investigating Sideroflexins’ functions constitutes an emerging research field of great interest and will certainly lead to main discoveries on mitochondrial physiopathology.

rdinary people and political leaders must know the sources of greenhouse gas emissions and their effect on global climate change before they have ability to make decisions to reduce emissions and increase sinks of these gases. These people must, however, understand where greenhouse gas emissions are formed and how reductions can be made: they must understand where carbon dioxide sinks are and how to preserve or increase these sinks. North Savo is the example used in this work to describe the present emissions and sinks. There are proposals on what should and could be done to reduce greenhouse gas emissions caused by traffic, heating, forests and agriculture. There are possibilities of reducing emissions of greenhouse gases in traffic and heating in spite of the fact that the province has a low population density with long distances between homes and workplaces and schools, and a cold climate. We believe that research will also find solutions for reducing greenhouse gases and protecting waters, which are used for recreational purposes and for raw water of drinking water in many places. Luckily forests cover large areas of North Savo and their growth is an important carbon dioxide sink. In addition, forest soils serve as a valuable storage of carbon. Besides carbon dioxide emissions, emissions of nitrous oxide and methane must also be considered since they are more potent greenhouse gases than carbon dioxide and land use can thus influence these gas emissions.

The World Health Organization’s Health Economic Assessment Tool (HEAT) for walking and cycling is a user-friendly web-based tool to assess health impacts of active travel. HEAT, developed over 10 years ago, has been used by researchers, planners and policymakers alike in appraisals of walking and cycling policies of both national and more local scales. HEAT has undergone regular upgrades adopting the latest scientific evidence. This article presents the most recent upgrades of the tool. Health impacts of walking and/or cycling in a specified population are quantified in terms of premature deaths avoided (or caused). In addition to the calculation of benefits from physical activity, HEAT was recently expanded to include assessments of the burden associated with air pollution exposure and crash risks while walking or cycling. Further, impacts on carbon emissions from mode shift to active travel modes can now be assessed. Monetization of impacts using Value of Statistical Life and Social Costs of Carbon now uses country-specific values. As active travel inherently results in often substantial health benefits as well as not always negligible risks, assessments of active travel behaviour or policies are incomplete without considering health implications. The recent developments of HEAT make it easier than ever to obtain ballpark estimates of health impacts and carbon emissions related to walking and cycling.

Mushroom production in Poland is an important and dynamically developing element of diverse agriculture. Mushroom spent compost (MSC) is major waste generated during production, i.e., MSC: mushrooms is ~5:1. To date, the main use of MSC is soil application as organic fertilizer. To date, several methods of MSC treatment have been researched and developed including production of compost, bioethanol, biogas, enzyme lactase, xylo-saccharides, and hydrogen. Torrefaction may be considered a novel approach for biomass valorization. Thus, we are pioneering the potential use of MSC valorization via torrefaction. We explored valorizing the waste biomass of MSC via thermal treatment – torrefaction (‘roasting’) to produce biochar with improved fuel properties. Here for the first time, we examined and summarized the MSC torrefaction thermogravimetric analyses, fuel properties data of raw biomass of MSC and biochars generated from MSC via torrefaction. The effects of torrefaction temperature (200~300 °C), process time (20~60 min), on fuel properties of the resulting biochars were summarized. The dataset contains results of thermogravimetric analysis (TGA) as well as proximate analyses of MSC and generated biochars. The presented data are useful in determining MSC torrefaction reaction kinetics, activation energy and to further techno-economical modeling of the feasibility of MSC valorization via torrefaction. MSC torrefaction could be exploited as part of valorization resulting from a synergy between an intensive mushroom production with the efficient production of high-quality renewable fuel.

The creation of hydrophobic, antifreeze and self-cleaning coatings is currently being pursued by many industrial sectors. The potential applications include the production of liquid and gas separators and filters, new materials, optical and microelectronic devices, and textiles and clothing. These coatings will also have wide application in the construction and automobile industries, shipping, and energy and agricultural sectors. The article proposes a simple approach to the creation of superhydrophobic and antifreeze coatings, by applying powder from multi-walled carbon nanotubes (MW-CNTs) to the sample surface. This method enables combination of the necessary factors: low surface energy, micro–nano-roughness and hierarchical multi-scale. The authors investigated the dependence of the wetting angle of such a surface on the time, type and degree of functionalization. The electrophysical properties of modified MW-CNTs were studied over wide frequency and temperature ranges. This method of obtaining hydrophobic coatings differs from currently available methods in that it is simpler to prepare, is of lower cost and has less environmental impact. The proposed approach can be used to create superhydrophobic coatings that have the additional function of removing static charge and therefore reducing surface heating, and which can be used in the field of energetics for protection against the freezing of wind turbine blades and aircraft surfaces.

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix materials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNTs content. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both static and dynamically varying compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.

In China's mountainous coastal terrain, the storm badly damaged low-rise buildings. At present, it is not clear how the relative position of buildings and mountains affects the surface of a low-rise building’s fluctuating coefficient. The study compared these results with the wind pressure distribution without the surrounding environment. The primary objective of this study is to examine the fluctuating coefficient variation rule based on the spacing between hillsides and buildings under 0° wind angle. Additionally, the study analyzes the fluctuating wind pressure coefficient across wind angles between 0°~90°. The distribution of wind pressure in different common hillside landforms was examined through a wind tunnel experiment, which also compared with the distribution in an open environment. The study examined the fluctuating coefficient as the distance between the building and the hillside changed, specifically for wind blowing at a 0° angle. Next, an analysis is conducted on the changing pattern of the fluctuating coefficient for low-rise buildings ranging from a wind angle of 0° to 90°. Simultaneously, the investigation examined the power spectrum and wind pressure’s probability distribution, while considering the proximity of the building to an adjacent hill. The findings indicated that the changing wind pressure factor on the surface of the structure differed based on the relative location of the hillside and the building. The roof's wind pressure coefficient fluctuated and gradually increased until it reached its peak, unaffected by the surroundings. The low-frequency energy decreased in windward eaves, while the high-frequency energy progressively rose as the distance between the hillside and the building increased. The wind pressure on the leeward side exhibited Gaussian characteristics in its probability distribution.

Smart farm is a technology that greatly helps improve the productivity and quality of crops and is being actively introduced into indoor environments such as green houses. However, it has not yet been distributed to field-grown crops. The main reason is that, unlike indoor environments, it is very difficult to collect sensor data for monitoring the growth environment of crops in open fields where weather conditions change significantly and power supply is difficult. Additionally, because various sensors are used, the data formats of the devices are different, making it difficult to process. This paper presents a field crop growth environment monitoring and big data analysis system. The proposed system first solves power supply and data communication problems using solar power generation and LPWA technology. Additionally, based on the oneM2M architecture, data from various sensors is transmitted to the server using standardized technology. The transmitted data is stored and managed on the server as big data, and can be used to predict the production and quality of field-grown crops and take appropriate measures. The proposed system is expected to create an environment optimized for the growth of field crops and help prevent and manage diseases.

We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

For many years, energy monitoring at the most disaggregate level has been mainly sought through the idea of Non-Intrusive Load Monitoring (NILM). Nevertheless, a practical application of this concept in the residential sector should address the underlying concerns raised by the technical specifications of case studies. From one side, such an operation must handle common matters related to the essence of any NILM system. Although this aspect has been thoroughly investigated by basic research, it is limited to the properties of public datasets. On the other side, it must deal with specific concerns corresponding to uncommon situations. These circumstances impose further restrictions on existent NILM schemes, however, they have been overlooked due to the lack of pertinent databases to scrutinize. Accordingly, this paper presents applied research on a potential solution to NILM for Quebec residences. It carries out a relevant investigation into the multi-faceted nature of this problem in order to reveal barriers to feasible implementations in the context of Quebec. This work commences with a concise discussion about the NILM idea to highlight its essential requirements for a fruitful practice. Afterward, it provides a comparative statistical analysis to represent the specificity and potential challenges of the case study in accordance with NILM necessities. For this purpose, the examination exploits data from real-world measurement systems in the same and European regions. Subsequently, this study focuses on a load identification exercise by proposing a combinatory approach that utilizes the promise of sub-meter smart technologies to integrate the intrusive aspect of load monitoring with the non-intrusive one. The former is aimed at extracting overall heating demand from the aggregate one by a supervised procedure based on Deep Learning (DL) models while the latter is designed for disaggregating the residual load through an unsupervised process on the basis of clustering techniques. The results demonstrate that geographically-dependent cases create electricity consumption scenarios under which existing NILM methods can be questioned. From a realistic standpoint, this research elaborates on critical remarks to realize viable NILM systems, particularly, in Quebec houses.

Low-sodium salt substitute (LSSS) has the potential in regulating sodium and potassium intake and has been available in China market for years. However, its real-world use and impact to sodium\potassium intake is unclear. Baseline data of 4000 adult participants who participated in three similar-designed randomized controlled trails were pooled together for this study. Self-reported awareness and use of LSSS were collected using the uniform questionnaire, and the 24-h urinary sodium and potassium excretion was used to estimate their dietary intake. Mixed-effects models were developed to assess the relationship between LSSS and 24-h urinary sodium and potassium excretion. 32.0% of the participants reported awareness of LSSS and 11.7% reported its current use. After adjusting location, sex, age, and education, compared with the group of participants unaware of LSSS, participants who were aware but not using LSSS and those who were using LSSS had a lower 24-h urinary sodium excretion by –356.1(95% CI: –503.9, –205.9) mg/d and –490.6(95% CI: –679.2, –293.7), respectively (p&lt;0.001). No significant difference was found for 24-h urinary potassium excretion and sodium-to-potassium ratio among the three groups (p&gt;0.05). In conclusion, although associated with lower sodium intake, the awareness and real-world use of LSSS are still very low in China.

Urinary incontinence (UI) is a common geriatric syndrome affecting bladder health and is especially prevalent in nursing homes (NHs). The aim of the study was to determine the prevalence of UI and its associated factors in 5 Spanish NHs. UI (measured with Minimum Data Set 3.0.), sociodemographic and health-related variables were collected. Chi- square (or Fisher’s) or Student’s t-test (or Mann Whitney U) for bivariate analysis were used, with Prevalence Ratio (PR) as an association measure. The prevalence of UI was 66.1% (CI:95%, 53.6–77.2) and was significantly associated with frailty (PR 1.84; 95%CI 0.96–3.53), faecal incontinence (FI) (PR 1.65; 95%CI 1.02–2.65), anxiety (PR 1.64; 95%CI 1.01–2.66), physical performance (PR 1.77; 95%CI 1.00–3.11) and cognitive state (PR 1.95; 95%CI 1.05–3.60). Statistically significant differences between incontinent-continent groups were found for activities of daily living (ADL) limitations, mobility, quality of life, sedentary behaviour (SB) and handgrip strength. It can be concluded that 2/3 of the residents experienced UI, and its significant associated factors were mainly physical (SB, frailty, physical performance, ADL limitations, mobility, FI and handgrip strength) followed by psycho-cognitive factors (cognition, anxiety and quality of life).

Today, more disciplines are intercepting each other, giving rise to “cross-disciplinary” research. Technological advancements in material science and device structure and production have paved the way towards development of new classes of multi-purpose sensory devices. Organic phototransistors (OPTs) are photo-activated sensors based on organic field-effect transistors that convert incident light signals into electrical signals. The organic semiconductor (OSC) layer and three-electrode structure of an OPT offer great advantages for light detection compared to conventional photodetectors and photodiodes, due to their signal amplification and noise reduction characteristics. Solution processing of the active layer enables mass production of OPT devices at significantly reduced cost. The chemical structure of OSCs can be modified accordingly to fulfil detection at various wavelengths for different purposes. Organic phototransistors have attracted substantial interest in a variety of fields, namely biomedical, medical diagnostics, healthcare, energy, security, and environmental monitoring. Lightweight and mechanically flexible and wearable OPTs are suitable alternatives not only at clinical levels but also for point-of-care and home-assisted usage. In this review, we aim to explain different types, working mechanism and figures of merit of organic phototransistors and highlight the recent advances from the literature on development and implementation of OPTs for a broad range of research and real-life applications.

Insulin-like growth factor binding proteins (IGFBPs) are critical modulators of the metabolism. In adults, IGFBPs are associated with obesity and insulin resistance but the association of IGFBPs with metabolic homeostasis in children and adolescents is not fully characterized. In this study we investigated the association of plasma IGFBPs (IGFBP-1, 3 and 7) with weight status, central adiposity and cardiovascular disease markers Hs-CRP and Ox-LDL. A total of 420 adolescents (age 11-14 years) were randomly recruited from public middle schools in Kuwait. IGFBPs were measured using bead-based multiplexing while Hs-CRP and Ox-LDL were measured using ELISA. IGFBP-1 levels were significantly lower in obese and overweight participants compared to normal weight children. Only IGFBP-1 was negatively associated with waist circumference to height (WC/Ht) ratio. IGFBP-1 was negatively correlated with Hs-CRP while IGFBP-3 and IGFBP-7 were negatively correlated with Ox-LDL. These data demonstrate a robust negative association of IGFBP-1, but not IGFBP-3 or -7, with overweight and obesity, and the inflammation marker Hs-CRP. Central adiposity (WC/Ht ratio) was a stronger predictor of IGFBP-1 than BMI-for-age z-score. IGFBP-1 could thus be used as a sensitive predictive diagnostic tool for obesity and its subsequent effects in screening and monitoring of obesity-related metabolic complications in adolescents.

The epidemic transmission of Zika virus (ZIKV) in Brazil has been identified as a cause of microcephaly and other neurological malformations in babies of ZIKV-infected women. This study provides a descriptive analysis, since the onset of symptoms to the delivery, of a cohort who were registered as having ZIKV infection in pregnancy, from November 2015 to December 2016. Suspected cases were registered at a referral center for infectious and tropical diseases in Manaus, in the Brazilian Amazonian region. A total of 834 women with suspected ZIKV in pregnancy were included, of whom 91.4% had confirmed pregnancy. Reverse-transcriptase polymerase chain reaction (RT-PCR) confirmed ZIKV infection in 42.2% of the cohort. In 35.2% of the cohort, ZIKV was the sole infection identified. Severe adverse pregnancy outcomes (abortion, stillbirth, or microcephaly) were observed in both RT-PCR ZIKV-positive (4.96%) and ZIKV-negative (2.15%) cases. Women with suspected ZIKV infection were much more likely to have adverse pregnancy outcomes if they were symptomatic during the first trimester of pregnancy (odds ratio 10.5; 95% confidence interval 4.0–27.0; p<0.001). Among pregnant women with suspected ZIKV infection, the occurrence of symptoms in the first trimester is associated with an especially high risk of severe adverse pregnancy outcomes.

The slate aggregate has long been perceived as a substandard, low quality waste material with its physical and chemical properties not being competitive with those of the primary aggregates. It is assumed that the slate aggregate particles are not strong, that is not durable and will not compact. This research aims to address those claims and review the available literature on the performance of the slate aggregate. The review inaugurates by analysing the physical, chemical and mechanical properties of slate, before expanding into a literature review of laboratory testing’s on the effect of moisture content on density, compaction and layer thickness of slate aggregate.The paper reviews case studies of construction projects in North Wales, where the slate aggregate has been used for general fill and road building for many years. Some of the case studies include the A55 coastal road and duelling of the A5 in Anglesey (WRAP, 2004), where slate aggregate was successfully used as sub-base. The paper also investigates why many civil engineers are reluctant to use the slate aggregate and regard the material as sub-standard, flaky aggregate. The research paper reviews the potential usages and various products the slate aggregate is suitable for and satisfies the requested standards. The final topic reviewed is the cost of transporting slate aggregate compared with the cost of transport for primary aggregate and the introduction of the Primary Aggregates Tax (Parliament of the United Kingdom, 2011). The last topic includes a critical analyses of the claims that the slate aggregate a commercially viable construction material despite its remote location (Woodward et al, 2004). The transportation cost and the supply chain complexities must be evaluated prior to considering the long-term sustainability of the product (Radanliev et al^1-6, 2014, 2015, 2016).

The Double Diaphragm Forming (DDF) process uses vacuum pressure and heat to pre-shape composite reinforcements between flexible diaphragms. Accurate modelling of heat transfer within DDF requires knowledge of the thermophysical properties of the constituent materials. This study investigates the specific heat and thermal conductivity of silicone diaphragms, carbon fibers (chopped and powdered), thermoplastic veils, and their combinations. Experiments measured the specific heat of each material using differential scanning calorimetry and the thermal conductivity of silicone and carbon fabric preforms using the transient plane source method and modified transient plane source method respectively. The influence of reheating cycles on specific heat of carbon fiber-veil samples and the effect of compaction on thermal conductivity of silicone and carbon fabrics were explored. While silicone exhibited linear specific heat behavior, the thermoplastic veil showed non-linearity due to phase change. The combined carbon fiber-veil samples demonstrated slight non-linear specific heat variations depending on reheating cycles. Thermal conductivity of the fabric preforms decreased with the addition of thermoplastic veil and under vacuum-compaction conditions. The established temperature-dependent property relationships provide valuable data for optimizing DDF preforming parameters and enhancing energy efficiency in composite manufacturing.

This comprehensive review explores the multifaceted landscape of supercapacitors, highlighting their pivotal role in meeting the global demand for efficient energy storage solutions. Supercapacitors, with their high power density, rapid charge-discharge cycles, and extended cycle life, offer a compelling alternative to conventional batteries and capacitors. The review delves into the fundamental mechanisms of energy storage in supercapacitors, categorizing them into Electrochemical Double-Layer Capacitors (EDLCs), pseudocapacitors, and hybrid capacitors. It discusses significant advancements in supercapacitor technology, including nanostructured materials, flexible and wearable supercapacitors, solid-state supercapacitors, and hybrid supercapacitors, highlighting their potential applications across industries such as transportation, renewable energy, consumer electronics, and industrial power management. Through continued research and development, supercapacitors are poised to play a pivotal role in driving the transition towards a greener and more efficient future.

The COVID-19 virus was first detected in Wuhan, China and its genesis was traced to infected bats, passed through an intermediate host to humans. COVID-19 or “Coronavirus” reached approximately 4 million confirmed cases in the United States by July 2020. The spread of this virus has affected both social and economic affairs on a global scale with more than 15 million confirmed cases worldwide in July 2020. The pandemic has proven a global public health and socio-economic crisis. In addition, the shelter-in-place orders provide an unprecedented opportunity for examining the resulting reduction in greenhouse gases and aerosols on the atmosphere. The Sentinel-5P satellite has shown distinct changes in atmospheric compounds over the COVID-19 epicenter in Wuhan. After Texas, U.S.A. established similar shelter-in-place orders to prevent the spread of the virus, the state’s industrial activity experienced an economic slowdown. This paper quantifies the changes in the atmosphere during the time of the COVID-19 slowdown over major cities in Texas and compares it to similar changes in Wuhan, China using satellite imagery.

Solventogenic Clostridium species are important for establishing sustainable industrial bioproduction of fuels and important chemicals. The inherent versatility of these species in substrate utilization and the range of solvents produced during acetone butanol-ethanol (ABE) fermentation make solventogenic Clostridium an attractive choice for biotechnological applications such as production of fuels and chemicals. The functional qualities of these microbes have thus been identified to be due to complex regulatory networks that play essential roles in modulating the metabolism of this group of bacteria. Genomes of solventogenic Clostridium species have relatively greater prevalence of genes that are intricately controlled by various regulatory molecules than most other species. Consequently, the use of genetic or metabolic engineering strategies that do not consider the underlying regulatory mechanisms will not be effective. Several regulatory factors involved in substrate uptake/utilization, sporulation, solvent production, and stress responses (Carbon Catabolite Protein A, Spo0A, AbrB, Rex, CsrA) have been identified and characterized. In this review, the focus is on newly identified regulatory factors in solventogenic Clostridium species, the interaction of these factors with previously identified molecules, and potential implications on substrate utilization, solvent production, and resistance/tolerance to lignocellulose-derived microbial inhibitory compounds.

This study analyzed the CO2 capture potential for Parque Natural Regional Serrania de las Quinchas buffer area in Colombia. For this purpose, multitemporal analysis for land covering for years 1989, 2000, 2006, 2011, 2017 and 2021 was made using the Normalized Difference Vegetation Index (NDVI), and Corine Land Cover (CLC) methodology. In the same way, Aboveground Biomass (AGB) was measured for representative parcels by measuring tree’s diameters and heights and applying the adequate allometric models; carbon content in soils was measured too. Results show that dense forest has grown since 1989 and the carbon stock in all the vegetation covers increased by 14,3% from 1989 until 2021, using literature data for tropical humid forests. If measured AGB values obtained in this study are used, the carbon stock average is 3 times this value. Measured carbon average content in AGB was 374,3 Ton C/Ha, well above the average for the content reported for humid tropical forests in Colombia; carbon content in soils was 897,19 Ton/Ha, 2,4 times that found in the AGB. In total, an average of 1271,49 Ton C/Ha (AGB+ soil) was found and a pattern of dense forest recovery was found, but in a more dispersed way than in the past. A very interesting potential for existing forests recovery was found for this area. Strategies for this include the development of sustainable practices, land use management, everything pursuing biodiversity preservation and the participation and leading of the local communities.

Polymer-based (nano)composite foams, especially those having a microcellular structure, containing suitable conductive (nano)fillers, have been shown to act as good shielding materials, hence coming as promising to act as shields in electronic devices, limiting/avoiding electromagnetic interference (EMI) pollution. Nevertheless, due to their high (micro)structural complexity, related to their multiphase nature, there is still a lot of unawareness behind the shielding mechanisms acting in these materials, coming as a necessity to study their microstructure-cellular/porous structure-properties relations, especially in terms of their electrical conductivity and EMI shielding efficiency (EMI SE). To target and control the electrical conductivity through a controlled distribution/dispersion of conductive nanofillers, single or combined (nanohybrids), as there is a direct relation between electrical conductivity and EMI SE, as well as the main EMI shielding mechanisms working on the developed microcellular structure of the foams, which are expected to be absorption-dominated or absorption/multiple reflection-based, are two of the main objectives when combining polymer foaming with the addition of conductive nanofillers. The present review work considers the recent developments and trends on polymer-based foams containing conductive nanofillers, especially carbon-based such as carbon nanotubes or graphene-based materials, as well as similar porous structures created using trending technologies such as 3D printing, for EMI shielding applications. It is divided in different sections, starting with the strategy of microcellular foaming to develop polymer-based foams with enhanced EMI shielding characteristics, especially focusing on technologies and methods using supercritical CO2 (sCO2); continuing with the use of polymer foams as templates to synthesize carbon foams with improved EMI shielding performance for high use temperature applications; the recent strategy of combining different functional (nano)fillers to create hybrid nanofillers/nanohybrids to be used at lower amounts as conductive fillers in polymer foams; the control and selective distribution of the nanofillers in terms of favoring the formation of a more effective conductive network and hence promote the enhancement of the EMI SE; the very recent use of computational approaches to tailor the EMI shielding properties of composite foams; and the very trending possibility of creating cellular components with varied porous structures from these materials using 3D printing; to finish, some future perspectives are discussed.

The importance of the national security of supply has been emphasized in recent years due to the COVID-19 pandemic and changes in operating environments. Thanks to autonomy and resiliency in fuel procurement, organizations with decentralized energy plants may be able to quickly adapt to the changing needs of society. The main aim of this study was to increase the sustainability of a Finnish CHP plant's wood procurement by determining the company's profitable wood procurement region while keeping the forests renewable. The income received from the sale of energy and the costs incurred from the procurement of wood were collected from the ERP system as input data for the developed DSS. The environmental sustainability of wood procurement was assessed by considering the additional costs caused through the EEAP mechanism if the carbon sink of the forest worsened due to wood procurement in the area. The supply chains were compared so that the CHP plant managers could adopt the best energy wood value chains. The results showed that updating the procurement strategy would be necessary. The CHP plant managers should purchase energy wood from a larger procurement area than the current one and focus on roadside purchases of wood. The Techno-Economic Wood Payment Ability Model was a useful part of the DSS to guide wood buyers toward sustainable wood procurement by increasing the share of renewable forests.

Electronic devices are sensitive to electromagnetic (EM) emissions requiring electromagnetic shielding protection to assure good operation, preventing noise, malfunctioning, or even burning. To assure protection, it is important to develop suitable material and design solutions for electronic enclosures. Most common enclosures are made with metal alloys by traditional manufacturing methods. However, resourcing to thermoplastic composites combined with additive manufac-turing (AM) technologies emerges as an alternative that enables to fabricate complex parts that are lightweight, consolidated and oxidation and corrosion resistant. In this research, an AM technique based in material extrusion was used to print 2 mm thick specimens with a multi-material made of micro-carbon fiber (CF) filled polyamide, reinforced, at specific layers, by continuous carbon fibers stacked with a 90° rotation to each other. Specimens electromagnetic shielding effectiveness (EMSE) was evaluated in the frequency band of 0.03 – 3 GHz by coaxial transmission line method. De-pending on the number of CF layers, the EM shielding obtained can up to 70 dB, with a specific shielding up to 60 dB.cm3/g, predominantly by absorption mechanism, being 22 times higher that without the CF layers. These findings fundament this innovative approach for lightweight cus-tomizable solutions for EM shielding applications.

Climate and land-use changes have been contributing to increase the occurrence of extreme wild-fires, shifting fire regimes and driving desertification, particularly in Mediterranean-climate regions. However, few studies have researched the effects of land-use change on fire regimes and carbon storage at the broad national scale. To address this gap, we used spatially explicit data from annual burned areas in mainland Portugal to build a typology of fire regimes based on the accumulated burned area and its temporal concentration (Gini index) between 1984 and 2019, which was combined with 2018 carbon stock data (above- and below-ground), and a landscape typology re-sulting from cluster analysis over land-use composition, diversity and configuration, to explore relationships between landscape types and the two major ecosystem services at stake: wildfire reduction and carbon stock. Cross tabulations, logistic and linear regressions were performed on these data and results revealed a strong relationship between landscapes dominated by maritime pine and eucalypt forest plantations and high-hazardous fire regime but hold the highest carbon stock. Shrubland-mixed landscapes were associated with lower carbon stocks but less hazardous fire regimes. Specialized agricultural landscapes, as well as mixed native forests and mixed agro-forestry landscapes, were the least associated with wildfires. In the case of agricultural landscapes however, this good wildfire performance is achieved at the cost of the poorest carbon stock, de-noting land degradation, whereas native forests and agroforestry landscapes strike the best trade-off between carbon stock and fire regime. Our findings support how nature-based solutions promoting wildfire mitigation and carbon stock ecosystem services may prevent and revert land degradation harming Mediterranean regions.

Earthworms and soil microorganisms contribute to soil health, quality and fertility, but their importance in agricultural soils is often underestimated. This study aims at examining whether and to what extent the presence of earthworms [Eisenia fetida (Savigny, 1826)] affected the a) soil bacterial community composition, b) litter decomposition, and c) plant growth (Brassica oleracea L., broccoli; Vicia faba L., faba bean). We performed a mesocosm experiment in which plants were grown outdoors for four months with or without earthworms. Soil bacterial community structure was evaluated by a 16S rRNA-based metabarcoding approach. Litter decomposition rates were determined by using the tea bag index (TBI) and litter bags (olive residues). Earthworm number almost doubled throughout the experimental period. Independently of the plant species, earthworm presence had a significant impact on the structure of soil bacterial communities, in terms of enhanced α- and β-diversity (especially that of Proteobacteria, Bacteroidota, Myxococcota, and Verrucomicrobia) and increased 16S rRNA gene abundance (+89% in broccoli and +223% in faba bean). Microbial decomposition (TBI) was enhanced in the treatments with earthworms, and showed a significantly higher decomposition rate constant (kTBI) and a lower stabilization factor (STBI), whereas decomposition in the litter bags (dlitter) increased by about 6% in broccoli and 5% in faba bean. Earthworms significantly enhanced root growth (in terms of total length and fresh weight) of both the plant species. Our results show the strong influence of earthworms and crop identity in shaping soil bacterial communities, litter decomposition and plant growth. These findings could be used for developing nature-based solutions that ensure the long-term biological sustainability of soil agro- and natural ecosystems.

Shale gas and coalbed methane are energy sources that partly or even mainly consist of methane stored in an adsorbed state in the pores of the organic-rich rock and coal seams. In this study, the graphene nanoslit model is employed to model the nanometer slit pores in shale and coal. The Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) modelling methods are used to investigate the mechanisms of adsorption and displacement of methane in the slit pore. It was found that the CVFF forcefield resulted in the largest adsorption amount, while the PCFF forcefield resulted in the least. The COMPASS and COMPASS II force fields led to similar results. As the width of the slit pore increases, the adsorption amount of gas molecules increases, and the number density profile of adsorbed methane molecules alters from a single adsorption layer to multi-adsorption layers. The minimum slit pore width at which methane molecules can penetrate the slit pore was found to be 0.7 nm. Moreover, it is demonstrated that by lowering the temperature, the adsorption rate of the methane increases since the adsorption is an exothermic process. Enhancing methane recovery was investigated by the injection of gases such as CO2 and N2 to displace the adsorbed methane. The comparison of adsorption isotherms of gas molecules provided the following order in terms of the amount of adsorption: CO2&gt;CH4&gt;N2.

Despite the use of commercial forest carbon protocols (CFCPs) for more than two decades, claiming ~566 MMtCO₂e and a market value of ~USD $15.7 billion, comparative analysis of CFCP methodology and offset results is limited. In this study, five widely used biometric-based CFCPs are characterized, and common characteristics and differences are identified. CFCP claims of net forest carbon sequestration are compared with results of directly measured CO₂ by eddy covariance, a meteorological method integrating gross vertical fluxes of forest and soil carbon, and the only alternative non-biometric source of net forest carbon sequestration data available. We show here that CFCPs share a structural feature delimiting forest carbon values by zero-threshold carbon accounting (gC m^-2 ≤ 0), a pattern opposite to natural emissions of forest CO₂ exchange based on direct measurement and a fundamental biological constraint on net forest carbon storage (i.e., soil efflux, ecosystem respiration). Exclusion of forest CO₂ sources to the atmosphere precludes net carbon accounting, resulting in unavoidable over-crediting of CFCP project offsets. CFCP carbon results are significantly different from global forest CO₂ net ecosystem exchange population results (FluxNet2015 gC m^-2) at the 95% to 99.99% confidence levels, inferring an annual median error of ~247% (gC m^-2), consistent with over-crediting. Direct CO₂ measurement provides an urgently needed alternative method for commercial forest carbon products that has the potential to harmonize global markets and catalyze the role of forests in managing climate change through nature-based solutions.

This is the first study to provide a systematic monetary benefit matrix, including greenhouse gas (GHG) emissions reduction benefits and air pollution reduction health co-benefits, for a change in on-the-road transport to low-carbon types. The benefit transfer method is employed to estimate the social cost of carbon and the health co-benefits via impact pathway analysis in Taiwan. Specifically, the total emissions reduction benefits from changing all internal combustion vehicles to either hybrid electric vehicles, plug-in hybrid electric vehicles, or electric vehicles would generate an average of US$760 million from GHG emissions reduction and US$2,091 million from health co-benefits based on air pollution reduction, for a total benefit of US$2,851 million annually. For a change from combustion scooters to light- or heavy-duty electric scooters, the average GHG emissions reduction benefits would be US$96.02 million, and the health co-benefits from air pollution reduction would be US$1,008.83 million, for total benefits of US$1,104.85 million annually.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

Soil organic carbon (SOC) is an essential condition for soil health and a potential sink for greenhouse gases. SOC dynamics in a long-term field experiment with mineral and organic fertilization on loamy sand Podzol in Vladimir Region, Russia, was traced with the dynamic carbon model RothC since 1968 until the present time. During this period, C stock increased 21% compared with the initial level in the treatment with the application of manure in an average annual rate of 10 t·ha-1. The model was also used to forecast SOC changes until 2090 for two contrasting RCP4.5 and RCP8.5 climatic scenarios. Until 2090, the steady growth of SOC stocks is expected in all compared treatments for both climate scenarios. This rate of growth was the highest until 2040, decreased in 2040-2070 and increased again in 2070-2090 for RCP4.5. The highest annual gain was within 21-27‰ under RCP4.5 and 16-21‰ in 2020-2040 in 0-20 cm soil layer. The expected accumulation of C allows increasing current C stock 1.6-1.7 times for RCP4.5 and 2.0-2.2 times for RCP8.5 scenario. Modelling demonstrated potentially more favourable conditions for SOC stability in arable Podzols than in Retisols in Central Russia in the 21st century.

Literature is inconsistent as to how coffee affects the features of the metabolic syndrome (MetS), and which bioactive compounds are responsible for its metabolic effects. We aimed to compare the in-vivo effects of unfiltered coffee with a selected mixture of its compounds on diet-induced MetS. 24 male Sprague-Dawley rats were fed a high-fat (35% W/W) food plus 20% W/W fructose in drinking water for 14 weeks, and were randomized into three groups: control, coffee, or nutraceuticals (5-O-caffeoylquinic acid, caffeic acid, and trigonelline). Coffee or nutraceuticals were provided in drinking water in a dosage equal to 4 cups/day in a human. Compared to the controls, only coffee supplementation decreased total food intake, weight gain, and estimated average plasma glucose. Surrogate measures of insulin resistance (fasting insulin, HOMA-IR, and oral glucose tolerance) were improved at endpoint in the coffee group. Circulating triglyceride levels were also reduced by coffee. Histopathological and quantitative measurements indicated lower grades of liver steatosis after long-term coffee consumption. In conclusion, a combination of phenolic acids and trigonelline was not as effective as coffee per se in improving the components of the MetS. This points to the role of other coffee chemicals and a potential synergism between compounds.

In this study, we evaluated chlorophyll fluorescence (CF) under two extreme illumination conditions at plant scale with a passive spectroradiometer. Fluorescence (F) was estimated by reading directly from radiance spectra of a variety of plants illuminated with light-emitting diode (LED) grow lights in the laboratory. Solar-induced fluorescence (SIF) was estimated from spectral measurements of the same plants under sunlight using the Fraunhofer Line Depth (FLD) method. Chlorophyll fluorescence yield (F_yield) and solar-induced fluorescence yield (SIF_yield) were calculated by normalizing F and SIF with absorbed photosynthetically active radiation (APAR). Two approaches to estimating APAR were compared: utilizing white reference spectra and reflected spectra versus white reference spectra combined with the fraction of absorbed photosynthetically active radiation (fPAR) derived from literature. Average F and SIF were different by a factor of approximately twenty-four (F = 0.110 ± 0.038 Wm⁻²μm⁻¹sr⁻¹ versus SIF = 2.60 ± 1.87 Wm⁻²μm⁻¹sr⁻¹). In contrast, the average normalized values F_yield and SIF_yield were within the margin of error of one another (F_yield = 0.022 ± 0.008 μm⁻¹sr⁻¹ and SIF_yield = 0.030 ± 0.020 μm⁻¹sr⁻¹). This study highlights the influence of APAR on CF and the importance of properly accounting for it when estimating yield and demonstrates the ability of two simple and portable experimental setups with a passive instrument to obtain fluorescence metrics.

This paper introduces an innovative nanotechnology-based approach that provides a pathway to enhance the energy release efficiency of nanoenergetic materials (nEMs) by harnessing self-synchronized collective atomic vibrations and phonon wave resonance within the transition domains between nanocomponents, without altering the material composition. The key innovation involves incorporating finely-tuned 2D-ordered linear-chain carbon-based multilayer nano-enhanced interfaces as programmable nanodevices into the transition domains using advanced multistage processing and assembly techniques. These programmable nanodevices enable precise control over self-synchronized collective atomic vibrations and phonon wave propagation, leading to synergistic effects. To activate and optimize these effects, a combination of various methods is employed, including energy-driven initiation of allotropic phase transformations, surface acoustic wave-assisted micro/nano-manipulation, heteroatom doping, directed self-assembly using high-frequency electromagnetic fields, and data-driven inverse design approaches. By leveraging a data-driven inverse design strategy and uncovering hidden structure-property relationships, we maximize energy release efficiency using the carbon nano-materials genome approach derived from multifactorial neural network-based predictive models. This approach not only unlocks new functionalities in nEMs but also improves environmental performance and safety levels. By pioneering transformative pathways for nEMs through harnessing phonon wave resonance in low-dimensional nanocarbon transition interfaces, this research brings significant advancements in the field.

Gas-water relative permeability curve is the foundation of gas reservoir dynamic analysis and numerical simulation. It is generally obtained through gas displacing water experiment. Referring to the existing national standards, gas-water relative permeability test is carried out for low-permeability and tight sandstone. The flow is discontinuous and the curve smoothness is poor, which affects the application of gas-water relative permeability curve. Based on the comparative analysis of a large number of mercury injection and NMR experimental results of low-permeability and tight sandstone, a method to characterize the throat radius distribution of low-permeability tight sandstone based on NMR T2 spectrum is explored. Combined with high-speed centrifugal experiment, the calculation formulas of core water saturation, phase relative permeability of gas-water under different centrifugal force are established. A new method of "nuclear magnetic resonance + high-speed centrifugation" for gas-water relative permeability curve test of low-permeability and tight sandstone is formed, and the test is carried out on Sulige low-permeability tight sandstone core. The results show that: (1) The shape of cumulative distribution curve of throat radius by mercury injection method is basically consistent with that of T2 relaxation time by NMR, and there is a good corresponding relationship between them. (2) The centrifugation process is similar to the gas displacing water process. With the decrease of water saturation, water centrifugation in rock core becomes more and more difficult until it become irreducible. (3) The test process of the new method is unified and standard and up to 6 cores can be tested at the same time. The calculation results of water saturation and relative permeability curve are reliable and the integral curve is smooth, which greatly improves the test efficiency of gas-water relative permeability curve in low-permeability and tight sandstone. The new method can be widely used to study the gas-water two-phase seepage law in low-permeability and tight sandstone gas reservoir.

A new clothing resistance model is described and applied to characterize the human thermal and moisture climates. The climate was described by the thermal (rcl,t) and evap-orative (rcl,e) resistances of comfortable, imaginary clothing. The key input variable of the model is the rate of sweating (λEsw). Since sweating is an individual-specific process, the model applies to the individual. The observations were carried out by a single individual in Martonvásár (Hungarian lowland, Central Europe) in the summer of 2023 and the winter of 2024. During the observations, the observer walked at a speed of 1.1-1.7 ms-1 in weather-appropriate clothing. Among the results, we would highlight the following: Dur-ing large environmental heat surpluses, the rcl,t values were found to be between 0.1-0.5 clo-t (clo-t = 0.155 m2·℃·W-1), while the rcl,e values fell between 0.4-0.8 clo-e (clo-e = 0.155 m2·hPa·W-1). The values of the parameters close to 0 were caused by intense sweating (λEsw > 200 Wm-2). The applicability of the model is limited and largely depends on the rela-tionship between λEsw and the metabolic heat flux density.

The paper describes an application of machine learning approach for parameter optimization. The method is demonstrated for the elasto-viscoplastic model with both isotropic and kinematic hardening. It is shown that the proposed method based on long-short term memory networks enabled to obtain reasonable agreement of stress-strain curves for cyclic deformation in low-cycle fatigue regime. The main advantage of the proposed approach over traditional optimization schemes lies in the possibility to get parameters for a new material without the necessity to conduct any further optimizations. As the power and robustness of the developed method was demonstrated on the very challenging problem (cyclic deformation, crystal plasticity, self-consistent model, isotropic and kinematic hardening), it is directly applicable to other experiments and models.