The generation of eucalypt sawdust has increased in Uruguay with the expansion of pulp and paper industrial sites. Currently, most of this readily available feedstock is either not used or applied for producing heat and power by combustion in biomass boilers. In this work, eucalypt sawdust was subjected to steam explosion as the first step for cellulosic ethanol production within the biorefinery concept. The effect of sawdust moisture content, pretreatment temperature and residence time were evaluated, along with the influence of water washing of steam-exploded solids on enzymatic hydrolysis and fermentation yields. After steam explosion, 60% xylans and 97% acetyl groups were recovered mainly as oligomers and acetic acid in the pretreatment liquor. Eucalypt sawdust moisture content affected the enzymatic hydrolysis performance and glucan conversion efficiency. Water washing after pretreatment improved hydrolysis efficiencies and ethanol production yields by 10% with respect to the unwashed pretreated solids at the same experimental condition. The best ethanol yields were obtained using PSSF (pre-saccharification and simultaneous saccharification and fermentation) after pretreatment at 205°C for 10 min, using sawdust with an 8% moisture content. In this case, 227 L ethanol and 40 kg total xylose (including xylo-oligomers) were obtained per ton of dry eucalypt sawdust.

The electron Transport layer (ETL) plays a crucial role in solar cell technology, particularly in perovskite solar cells (PSCs), where nanostructured TiO2 films have been investigated as superior ETL’s compared to compact TiO2. In this study we explore the nanocolumnal growth of TiO2 in the anatase phase, for bilayer thin films by magnetron sputtering (MS) technique and glancing angle deposition (GLAD). By optimizing the growth parameters, we achieved the formation of TiO2 nanocolumns with a cross-sectional diameter ranging from 50 to 75 nm. The average thickness of the films exceeded 12.71 ± 0.5µm , while the filaments exhibited an inclination angle close to 70◦ , corresponding to the deposition angle. Furthermore, we observed a correlation between the quality of the initial layer and enhanced growth of the TiO2 nanocolumns.

The structural stability of γ-boron is investigated using Raman spectra under high pressures up to 126 GPa at ambient temperature. The pressure dependence of all the Raman-active modes of the γ-boron is reported. We also observe amusing changes within the B3g and B1g Raman-active vibrational modes, which results in the phenomenon of merging first and then separating of the Raman peaks. In addition to the Raman measurements, the changes in crystal structure and force constants are calculated to reasonably explain the discrepancy between the two Raman modes in response to pressure. The results of the continuous shifts for all Raman modes with increasing pressure indicate that γ-boron remains stable below this pressure value, with no changes in either symmetry or structure.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

The functions of annexin A1 (ANXA1) that is expressed on membranes and in cytoplasmic granules have been fully described. Nonetheless, the role of this protein in protecting against DNA damage in the nucleus is still emerging and requires further investigation. Here, we investigated the involvement of ANXA1 in DNA damage response in placental cells. Placenta was collected from ANXA1 knockout mice (AnxA1-/-) and pregnant women with gestational diabetes mellitus (GDM). The placental morphology and ANXA1 expression, which are related to the modulation of cellular response markers in the presence of DNA damage, were analyzed. Total area of AnxA1-/- placenta was smaller because of reduced labyrinth zone, enhanced DNA damage, and impaired base excision repair (BER) enzymes, which resulted in the induction of apoptosis in the labyrinthine and junctional layers. The placentas from pregnant women with GDM showed reduced expression of AnxA1 in the villous compartment, increased DNA damage, apoptosis, and reduction of enzymes involved in the BER pathway. Our translational data provide valuable insights into the possible involvement of ANXA1 in the response of placental cells to oxidative DNA damage and represent advancement in investigations on the mechanisms involved in placental biology.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

Abstract: Pomegranate peels are important source of polyphenols with remarkable interest in food, pharmaceutical and cosmetic industry. An improved extraction of total polyphenolic com-pounds (TPC) from pomegranate peels by Solid-State Fermentation (SSF) was achieved. A Box Hunter & Hunter (BHH) followed by Central Composite Design (CCD) were performed to assess the effect of the process variables on TPC release. The statistic designs indicate that the best TPC extraction (234.85 mg GAE/gdm) by means of SSF occurs, at 42°C, 50 % moisture, pH 5.0, mineral solution (g/L): NaNO3 (3.83), KH2PO4 (1.52), MgSO4 (4.66) and KCl (1.52) at 36 h. At the best fer-mentation conditions, TPC (248.78±1.24 mgGAE/gdm) increased 5.96-fold than values previously reported and antioxidant activity [AA] increased 5.81-fold than the value obtained before the SSF optimization. High-valued citric acid, α and β punicalin, α and β punicalagin, punigluconin, gal-loyl-HHDP hexoside and ellagic acid molecules were identified. The increased extraction of TPC by SSF provides a suitable alternative for pomegranate peels valorization through the re-covery of molecules with high added value with potential use in food, pharmacy and cosmetic industries; a diversification in the use of food agroindustry by-products is obtained as approach to the circular economy model through biotechnological processes.

With the aim to improve cladding coating quality and prevent cracking, this paper established an extreme high-speed laser cladding thermo-mechanical coupling simulation model to study the evolution of the temperature field and residual stress distribution. Process parameters that impacted the macroscopic morphology of single-pass coatings were investigated. Numerical calculations and temperature field simulations were performed based on the process parameter data to validate the effect of the temperature gradient and cooling rate on the coating structure and the residual stress distribution. The results showed that a good coating quality could be achieved using a laser power of 2400 W, a cladding rate of 20 m/min, and a powder feeding rate of 20.32 g/min. The coatings’ cross-sectional morphology corresponded well with the temperature distribution predicted by numerical modeling of the melt pool. The microstructure of the molten coatings is affected by the temperature gradient and cooling rate, which vary greatly from the bottom to the middle to the top. Maximum residual stress appears between the bonding region of the coatings and the substrate, and the coatings themselves have significant residual stress in the form of tensile strains that are mostly distributed in the direction of the laser cladding speed.

This paper analyzed the main diseases of the friction high-strength bolt (FHSB) joints in order to study the characteristics of the corrosion products of the joints in steel bridge and the influence factors. Seven representative FHSB connection pairs and eight steel plate samples were selected from the Dongying Shengli Yellow River Bridge, which has been in operation for 33 years. Then Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD) were used to analyze the microscopic morphology and chemical composition of the corroded surface of the samples. Finally, this paper discussed the relationship between the corroded sample surface and the environmental corrosion. The research results showed that construction quality problems, such as non-standard hole expansion, segmental slab joint dislocation and contact surface pollution, accelerated corrosion of the contact surface. With the increase of corrosion degree of joints, the contact surface of aluminum spraying layer gradually changed from a rugged and dense state to a smooth and porous powder state. With the corrosion of the steel plate substrate, the contact surface gradually changed from a fluffy stratified state to a surface bonding state. It was inferred that the friction coefficient of the FHSB connection node on the corroded aluminum sprayed contact surface first decreased and then increased. The corroded node samples detected not only a large number of S and Cl elements, but also the oxides of Mn, Si and other elements as well as FeS. It was speculated that node corrosion was also related to atmospheric (acid rain) and industrial dust and other corrosive environments. Almost all samples detected the component SiO2 of the Yellow River soil, as well as Mg, Ca, K, Na and other elements at the same time, which is basically consistent with the component elements of the Yellow River soil. Therefore, it was inferred that it was related to the inclusion of the Yellow River soil.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

Purpose: This study investigates the impact of different intensity normalization (IN) methods on the overall survival (OS) radiomics models’ performance of MR sequences in primary (pHGG) and recurrent high-grade glioma (rHGG). Methods: MR scans acquired before radiotherapy were retrieved from two independent cohorts (rHGG C1: 197, pHGG C2: 141) from multiple scanners (15, 14). The sequences are T1 weighted (w), contrast-enhanced T1w (T1wce), T2w, and T2w-FLAIR. Sequence-specific significant features (SF) associated with OS, extracted from the tumour volume, were derived after applying 15 different IN methods. Survival analyses were conducted using Cox proportional hazard (CPH) and Poisson regression (POI) models. A ranking score was assigned based on the 10-fold cross-validated (CV) concordance index (C-I), mean square error (MSE), and the Akaike information criterion (AICs), to evaluate the methods’ performance. Results: Scatter plots of the 10-CV C-I and MSE against the AIC showed an impact on the survival predictions between the IN methods and MR sequences (C1/C2 C-I range: 0.62-0.71/0.61-0.72, MSE range: 0.20-0.42/0.13-0.22). White stripe showed stable results for T1wce (C1/C2 C-I: 0.71/0.65, MSE: 0.21/0.14). Combat (0.68/0.62, 0.22/0.15) and histogram matching (HM, 0.67/0.64, 0.22/0.15) showed consistent prediction results for T2w models. They were also the top-performing methods for T1w in C2 (Combat: 0.67, 0.13; HM: 0.67, 0.13), however, only HM achieved high predictions in C1 (0.66, 0.22). After eliminating IN impacted SF using Spearman’s rank-order correlation coefficient, a mean decrease in the C-I and MSE of 0.05 and 0.03 was observed in all four sequences. Conclusion: The IN method impacted the predictive power of survival models. Thus, performance is sequence-dependent.

Evolutionary ecology may be described as explaining ecology through evolution and vice versa, but one may also view it as an integration of the two fields, where one takes the view that ecology and evolution are inseparable, and one can only begin to understand the biology of organisms by synthesizing the two fields. An example of such a synthesis is the biology of high fecundity and the associated concept of sweepstakes reproduction, or skewed individual recruitment success. As an illustration we consider selection at linked sites under various dominance and epistasis mechanisms in a diploid population evolving according to random sweepstakes and experiencing recurrent bottlenecks. Using simulations we give a few examples of the impact of the stated elements on selection. We show that depending on the dominance mechanisms random sweepstakes can shorten the time to fixation (conditional on fixation) of the fit type at all sites. Bottlenecks tend to increase the fixation time, with random sweepstakes counteracting the effects of bottlenecks on the fixation time. Understanding the effect of random sweepstakes, recurrent bottlenecks, dominance mechanisms and epistasis on the fate of selectively advantageous mutations may help with explaining genetic diversity in natural highly fecund populations possibly evolving under sweepstakes reproduction.

The turbulent Poiseuille flow between two parallel plates is one of the simplest possible physical situations, and it has been studied intensively. In this paper, we propose a modified Prandtl-van Driest mixing length that satisfies both boundary conditions and wall damping effects. With our new formulations, we numerically solve the problem and, moreover, propose an approximate analytical solution of mean velocity. As applications of our solution, an approximate analytical friction coefficient of turbulent Poiseuille flow is proposed.

Background: Some patients who have recovered from COVID-19 have experienced a range of persistent symptoms or the appearance of new ones after a SARS-CoV-2 infection. These symptoms can last from weeks to months, impacting everyday functioning to a significant number of patients. Methods: A cross-sectional analysis based on an online, self-reporting questionnaire was conducted in Ecuador from April to July 2022. Participants were invited by social media, radio, and TV to voluntarily participate in our study. A total of 2103 surveys were included in this study. We compared socio-demographic variables and long-term persisting symptoms at low (< 2,500 m) and high altitude (>2,500 m).Results: Overall, 1100 (52.3%) responders claimed to have long-term symptoms after SARS-CoV-2 infection. Most of these symptoms were reported by women (64.0%), the most affected group was young adults (68.5%), and the majority of long-haulers were mestizos (91.6%). We found that high altitude residents were more likely to report persisting symptoms (71.7%) versus those living at lower altitudes (29.3%). The most common symptoms were fatigue or tiredness (8.4%), hair loss (5.1%) and difficulty concentrating (5.0%). The highest proportion of persisting symptoms was observed among those who received an incomplete vaccine scheme.Conclusions: This is the first study describing post-COVID symptoms' persistence in low and high-altitude residents. Our findings demonstrate that women, especially those aging between 20-40, are more likely to describe sequalae associated with post-COVID. We also found that living at a high altitude was associated with earlier onset and longer symptom duration. Finally, we found a greater risk to report long lasting symptoms among women, those with previous comorbidities and those who had a severer acute SARS-CoV-2 infection.

Mixture of abramis brama (freshwater bream), carassius carassius (crucian carp), and sander lucioperca (pike perch) scales was used for the preparation of fish scale powder containing about 26.5 wt. % of removed when heating components preferably of organic nature, and 63.5 wt. % of mineral components. Fish scale powder enriched with inorganic components was prepared from washed, dried, and ground fish scale mixture using vibration sieving. Inorganic powders consisting of hydroxyapatite and magnesium whitlockite were obtained via heat treatment of this fish scale powder at 800-1000 oC. Particles of these inorganic powders consisted of sintered grains with dimensions less than 100 nm after heat treatment at 800 oC, less than 200 nm after heat treatment at 900 oC, and 100-500 nm after heat treatment at 1000 oC. Fish scale powder enriched with inorganic components as well as heat-treated inorganic powders consisting of hydroxyapatite and magnesium whitlockite can be recommended for the production of different materials such as ceramics or composites.

In the diagnosis of olfactory neuroblastoma (ONB), the presence of S-100–positive sustentacular cells surrounding the tumor is important; however, these are also present in normal nasal sinus epithelium. Although ONB often has a different final diagnosis, complete resection of the tumor has a good prognosis and minimally affects the patient's treatment plan. When the tumor extends around the internal carotid artery (ICA), complete resection is difficult due to the high risk of vascular injury; revascularization using a high-flow bypass can avoid this complication. In the present case, the tumor was located in the left sphenoid sinus and extended around the ICA. Preoperative biopsy tissue was positive for neuroendocrine markers and slightly positive for S-100 protein, leading to a diagnosis of ectopic ONB. High-flow bypass revascularization with trapping of the ICA allowed complete tumor resection. The postoperative histopathological diagnosis was neuroendocrine carcinoma, showing no S-100 protein–positive cells. There was no sign of recurrence two and a half years after surgery without additional treatment. This case demonstrates that the presence of S-100 protein–positive cells in ONB may be misleading. Although misdiagnosis of ectopic ONB should be anticipated, a complete resection of the tumor is an effective treatment strategy.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

Phenotypic characterization of crop genotypes is an essential yet challenging aspect of crop management and agriculture research. Digital sensing technologies are rapidly advancing plant phenotyping and speeding-up crop breeding outcomes. However, off-the-shelf sensors might not be fully applicable and suitable for agriculture research due to diversity in crop species and specific needs during plant breeding selections. Customized sensing systems with specialized sensor hardware and software architecture provide a powerful and low-cost solution. This study designed and developed a fully integrated Raspberry Pi-based LiDAR sensor named CropBioMass (CBM), enabled by internet of things to provide a complete end-to-end pipeline. The CBM is a low-cost sensor, provides high-throughput seamless data collection in field, small data footprint, injection of data onto the remote server, and automated data processing. Phenotypic traits of crop fresh biomass, dry biomass, and plant height estimated by CBM data had high correlation with ground truth manual measurements in wheat field trial. The CBM is readily applicable for high-throughput plant phenotyping, crop monitoring, and management for precision agricultural applications.

Capacitor banks are widely used in current electrical transmission systems in order to improve power quality and increase efficiency. Utilizing high voltage components such as, shunt capacitors in the power grid imposes new challenges to the system which are required to be addressed. One of these challenges is corona discharges that can have negative impacts on capacitor banks such as power loss, insulator erosion followed by equipment failure, and radio interference. Although previous studies have almost exclusively focused on optimization of corona suppression rings for transformers and transmission lines, no specific studies have conducted regarding high voltage capacitor banks. This paper presents a novel study concerning verification and development of corona discharge suppression models on AC and DC capacitor banks with two different voltage levels. The employed method is based on the Maxwell’s equations and finite element method (FEM) which is implemented with the help of COMSOL Multiphysics© software. Results have verified the necessity of suppression methods as well as the efficiency of proposed solutions. Corona inception voltage levels are identified and effective factors on its appearance are reviewed. Analyses of proposed solutions have shown significant improvements in optimization of corona suppression methods as well as enhancement of maintenance maneuverability.

This article discusses a transformer-free, high-efficiency DC-DC converter besides renewable energy applications. The traditional buck-boost, classic Zeta, Sepic, and Cuk converter does have the benefits of a simple design, low cost, as well as the capacity to execute voltage step-up and step-down. Conversely, because of the detrimental consequences of the parasitic constraints of the device, the voltage conversion gain of the traditional DC-DC converter is much more restricted and the efficiency is also significantly smaller, whereas this proposed converter does have a higher voltage gain and efficiency because it is used in a single power switch, resulting in reduced switching losses and voltage stress. The said converter's design is very simple, which simplifies the operation control and reduces switching and conduction losses, leading to an efficiency of 97.4 percent. This converter seems to have the same capabilities as the Zeta converter, including continuous desired output current and desired buck-boost operation. Such an article offers the operation principle and steady evaluation, as well as a comparison with other existing high step-up configurations. The proposed converter employs a fuzzy logic controller, which improves the voltage level as well as reduces the time taken to set the voltage output of a conventional PI and ANN controller, especially in comparison to the FLC controller. For deployment, Experimental Result and MATLAB/Simulink has been used, and the modeling results indicate that the proposed controller performance has improved

Biofuels have many environmental and practical benefits as a transportation fuel. They are among the best alternatives to fossil fuels due to their capacity for negative carbon emissions, which is vital for archiving the global ambition of a Net-Zero Economy. However, conventional biofuel production takes place on inland sites and relies on freshwater and edible crops (or land suitable for edible crop production), which has led to the food vs fuel debate. It also suffers technical and economical barriers due to the energy balance and the cost of production compared to fossil fuels. Establishing a coastal integrated marine biorefinery (CIMB) system for the simultaneous production of biofuels, high-value chemicals, and other co-products could be the ultimate solution. The proposed system is based on coastal sites and relies on marine resources including seawater, marine biomass (seaweed) and marine microorganisms (marine yeasts and marine microalgae). The system will not require the use of arable land and freshwater in any part of the production chain and will be linked to offshore renewable energy sources to increase its economic and environmental value. This article aims to introduce the CIMB system as a potential vehicle for addressing global warming and speeding the global effort on climate change mitigation as well as increasing global water, food and energy security. I hope this perspective may serve to draw attention into research funding for this approach.

Background: Patients with severe chronic kidney disease (CKD G4-G5) often have chronically elevated high-sensitivity cardiac troponin T (hs-cTnT) values above the 99th percentile of the upper reference limit. In these patients, optimal cutoff levels for diagnosing non-ST-elevation acute cor-onary syndrome (NSTE-ACS) requiring revascularization remain undefined. Methods: Of 11,912 patients undergoing coronary angiography from 2012 to 2017 for suspected NSTE-ACS, 325 (3%) had severe CKD. Of these, 290 with available serial hs-cTnT measurements were included and 300 matched patients with normal renal function were selected as a control cohort. Results: Diagnostic performance for patients with severe CKD was high at presentation and similar to that of the control population (AUC, 95% CI: 0.81, 0.75-0.87 versus 0.85, 0.80-0.89, p=0.68) and the ROC-derived cutoff value at presentation was 4 times higher compared to the conventional 99th percentile. Combining the ROC-derived cutoff levels for hs-cTnT at presentation and absolute 3-hour changes, sensitivity increased to 98%, PPV and NPV improved up to 93% and 86%, re-spectively. (4) Conclusions: In patients with severe CKD and suspected ACS the diagnostic accu-racy of hs-cTnT for the diagnosis of NSTE-ACS requiring revascularization is improved by using higher assay specific cutoff levels combined with early absolute changes.

Growth benefits of high speed rail (HSR) for enterprises are not automatic, but require a buoyant local economy and a robust strategy. Against above background, main objectives of ex-ante case study have been to investigate local socio-economic and spatial impacts of proposed HSR project around Ahmedabad station area on Mumbai-Ahmedabad HSR corridor, analyze the opportunities and challenges of HSR development and draw policy implications. Qualitative research methodology has been used to elicit the perceptions and perspectives of randomly selected 43 small, medium and large enterprises. Data has been analyzed using descriptive statistics. The study reveals that HSR induced greater human interaction will activate local economy, improve business efficiency and generate employment. Frequent travels on business trips can influence enterprises decision to settle near HSR station for easy access and likely to promote realty development. The proposed HSR project should be developed in synergy with urban dynamics of cities in transition and metropolitan service cities. Poor public transport connectivity is likely to be a major challenge in improving HSR accessibility and enhancing overall impacts of HSR, which can be improved by developing an integrated urban transport system, for which cooperation of all stakeholders and coherence with firms’ strategies is essential.

This paper presents two designs of high-efficiency polarizer reflectarray antennas able to generate a collimated beam in dual-circular polarization using a linearly polarized feed, with application to high-gain antennas for data transmission links from a Cubesat. First, an 18 cm x 18 cm polarizer reflectarray operating in the 17.2 - 22.7 GHz band has been designed, fabricated and tested. The measurements of the prototype show an aperture efficiency of 52.7% for right-handed circular polarization (RHCP) and 57.3% for left-handed circular polarization (LHCP), both values higher than those previously reported in related works. Then, a dual-band polarizer reflectarray is presented for the first time, which operates in dual-CP in the frequency bands of 20 and 30 GHz. The proposed antenna technology enables a reduction of the complexity and cost of the feed chain to operate in dual-CP, as a linear-to-circular polarizer is no longer required. This property, combined with the lightweight, flat profile and low fabrication cost of printed reflectarrays, makes the proposed antennas good candidates for Cubesat applications.

This review highlights normal and tumor tissue vasculature, immunological changes, and phenotypic alterations (VIP model) as fundamental in abscopal interaction. In the stereotactic body radiotherapy (SBRT) and immunotherapy era, we are moving toward “immunological radiation planning,” i.e., radiation scheduling with abscopal effect as a vital endpoint as well. Towards this end, this manuscript presents specific diagrammatic tumor models to optimize the outcome of abscopal response in SBRT, based on the principle of the four R’s - Repair, Redistribution, Repopulation, and Reoxygenation of radiotherapy. The article highlights the importance of restricting the dose of SBRT to < 10 Gy per fraction, appropriate use of dose painting, and concomitant/delayed SBRT boost potential. Current literature indicates that immunotherapy should not precede but follow SBRT within seven days. Included is the review of integrating “cyclical” antiangiogenics, immune adjuvants/immune-metabolites as abscopal effect enhancers with SBRT. The importance of proton, carbon-ion SBRT is dealt with briefly. Proposed six fundamental requirements for augmentation of the abscopal cascade are listed. The existing exploratory results need to develop a definitive strategy amidst complex interactions in SBRT, immunotherapy, immune-adjuvants, & abscopal effects. We now have enough literature evidence to convert “abscopal by chance” to “abscopal by design” by harmonized combinatorial approach.

We propose a chemical language processing model to predict polymers’ glass transition temperature (Tg) through a polymer language (SMILES, Simplified Molecular Input Line Entry System) embedding and recurrent neural network. This model only receives the SMILES strings of polymer’s repeat units as inputs and considers the SMILES strings as sequential data at the character level. Using this method, there is no need to calculate any additional molecular descriptors or fingerprints of polymers, and thereby, being very computationally efficient and simple. More importantly, it avoids the difficulties to generate molecular descriptors for repeat units containing polymerization point `*’. Results show that the trained model demonstrates reasonable prediction accuracy on unseen polymer’s Tg. Besides, this model is further applied for high-throughput screening on an unlabeled polymer database to identify high-temperature polymers that are desired for applications in extreme environments. Our work demonstrates that the SMILES strings of polymer’s repeat units can be used as an effective feature representation to develop a chemical language processing model for predictions of Tg. The framework of this model is general and can be used to construct structure-property relationships for other polymer’s properties.

In the last decade, readily available electronic devices have created unprecedented opportunities for teens to access a wide variety of information and media – both positive and negative – on the internet. Despite the increasing number of initiatives taking place worldwide intended to assess and mitigate the online risks encountered by children and adolescents, there is still a need for a better understanding of how adolescents use the internet and what consequences they may face. We conducted a cross sectional online survey of a convenience sample of 733 8th and 9th grade students in Utah. The survey contained eight questions regarding students’ exposure to three types of online risk scenarios: content risk, contact risk, and commercial risk. Independent variables included students’ online behaviors, use of social media and private messaging apps, and adult supervision of online activities. Logistic and negative binomial regression models indicated that female gender, social media use, and chatting with strangers were associated with exposure to multiple unsafe online scenarios. Our results provide critical information to practitioners involved in the development of educational initiatives by building a profile of potentially risky online behaviors and allow them to tailor their initiatives to meet the needs of more vulnerable populations.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

In view of the preparation for a post-LHC collider, the high-energy physics (HEP) community started from 2010 to discuss various options, including the use of HTS for very high field dipoles. Therefore, a small program was set in Europe aiming at exploring the possibility of using HTS for accelerator quality magnets. Based on various EU funded programs, though at modest levels, has enabled the European community of accelerator magnets to start getting experience in HTS and addressing a few issues. The program was based on use of REBCO tapes to form 10 kA Roebel cables, to be used to wind small dipoles of 30-40 mm aperture in the 5 T range. The dipoles are designed to be later inserted in a background dipole field (in Nb3Sn), to reach eventually a field level in the 16-20 T range, beyond the reach of LTS. The program is currently underway: more than 1 km tape of high performance (Je &gt; 500 A/mm2 at 20 T, 4.2 K has been manufactured and characterized, various 30 m long Roebel cables have been assembled and validated up to 13 kA, a few dipoles have been wound and tested, reaching at present 4.5 T in stand-alone (while a dipole made from race track coils with no-bore exceeded 5 T using stacked tape cable) and a test in a background field is being organized.

This paper reviews state of the art Additive Manufactured (AM) IN718 alloy intended for high temperature applications. AM processes have been around for decades and have gained traction in the past five years due to the huge economic benefit it brings to manufacturers. It is crucial for the scientific community to look into AM IN718 applicability in order to see a step-change in the production. Microstructural studies reveal that the grain structure plays a significant role in determining the fatigue lifespan of the material. Controlling IN718 respective phases such as the ϒ’', δ and Laves phase is seen to be crucial. Literature reviews have shown that the mechanical properties of AM IN718 were very close to its wrought counterpart when treated appropriately. Higher homogenization temperature and longer ageing were recommended to dissolve the damaging phases. Various surface enhancement techniques were examined to find out their compatibility to AM IN718 alloy that is intended for high temperature application. Laser shock peening (LSP) technology stands out due to the ability to impart low cold work which helps in containing the beneficial compressive residual stress it brings in high temperature fatigue environment.

The use of cow bones for biomaterial is still limited; accordingly, the cow bones waste has low economic value. Basically, a human’s and a cow’s bones are the same in terms of their forming compound. Aluminum (Al) has the potential to combine with hydroxyapatite (HAp) to make metal matrix composites (MMC) that have the potential for biomaterials. Compatible elements to be combined with Al and HAp are magnesium (Mg), titanium (Ti), and Copper (Cu), used self-high propagating temperatures synthesis (SHS). MMC can be processed to be a useful, solid product. Applying pressure to the SHS reaction and heating process may result in biomaterial composite product consisting of some matrix materials such as Al come from cans materials used in the experiment was HAp that was processed from cow bones calcination, added by can that contained aluminum and wetting agent, namely magnesium. The exothermic temperature was 800-900°C. The compaction process was done to allow materials to be bound. Based on the ASTM F138 standard for element of biomaterials, the porosity value was below 30% and hardness level above 40 HV. Cow bones and can-based composite sample with the composition of HAp-Al-Mg: 85%-10%-5% met the standard since the hardness value was: 73.3 HV with a porosity value of 29.88%.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

Conventional radiation therapy uses white X-rays that consist of a mixture of X-ray waves with various energy levels. In contrast, a monochromatic X-ray (monoenergetic X-ray) has a single energy level. Irradiation of high Z elements with a synchrotron generated monochromatic X-ray with the energy at or higher than the K-edge energy of the element results in the production of the Auger electrons that cause DNA damage leading to cell killing. Delivery of high Z elements into cancer cells and tumor mass can be facilitated by the use of nanoparticles. Mesoporous silica nanoparticles (MSNs) have been shown to be effective in delivering high Z elements to cancer cells. A proof of principle experiment was reported that demonstrated the feasibility of this approach. This opens up a possibility to pursue the Auger cancer therapy by the combined use of MSNs loaded with high Z elements and monochromatic X-rays. Similar cancer therapies using other types of quantum beams such as neutron, proton and carbon ion beams can be envisioned.

The paper provides information on significant contamination of real laboratory water with hydrophilic microimpurities. This fact suggests that researchers are practically dealing with microdispersed systems. However, this fact is usually neglected in the discussions of the causes of the anomalous properties of water. We will show that, when exposed to various factors of physical nature, water demonstrates reactions of the same type, namely, increased pH and electrical conductivity, reduced redox potential and viscosity, and enhanced bioavailability. Each exposure is accompanied by the destruction of aggregates of the dispersed phase and its transition to a fine-dispersed state. The relationship between this phenomenon and the change in the physicochemical properties of water is discussed.

The origin and significance of the tonalite–trondhjemite–granodiorite (TTG) units and the familiar metabasite xenoliths they host in the Yangtze Craton, China, remain controversial, and resolving these issues is important if we are to understand the evolution of the early Yangtze Craton. We focused on biotite–tremolite schist xenoliths in the Archean TTG units of the Kongling high-grade metamorphic terrane, and U–Pb dating of their zircons yielded ²⁰⁷Pb/²⁰⁶Pb ages of ca. 3.00 Ga, which provides a minimum age for the formation of the pre-metamorphic basic igneous rock. The host TTGs and late intrusive granitic dikes yield three groups of upper intercept ages at 2.87–2.88, 2.91–2.94, and 3.07 Ga, and a concordant age at 2.94 Ga, which suggest that the Yangtze continental nucleus underwent three important metamorphic–magmatic events in the Mesoarchean at ca. 3.00, 2.94, and 2.87 Ga. The biotite–tremolite schists have high ratios of K₂O/Na₂O and high contents of CaO, Cr, and Ni, thus showing the characteristics of high-K calc-alkaline island-arc volcanic rocks (basalt–andesite) that form by the partial melting of subducted oceanic crust. The data also provide further proof that a Mesoarchean metamorphic basement exists in the Yangtze Plate. Derivation of the magmatic protoliths of the biotite–tremolite schist enclaves from an oceanic crust during slab subduction, and the presence of these xenoliths within the TTG suite, indicate the existence of the initiation of plate tectonics during the Mesoarchean (≤2.94 Ga).

Real-time evolution of the electron densities under excitations in La₂CuO₄ was calculated by the time-dependent density functional theory (TDDFT). The author found, for the first time, under excitations, the electron cloud of Cu²⁺ changes obviously and the characteristic frequencies are 83 meV and 36 meV, respectively, for two different modes. The results are unexpected and close to that of lattice vibrations. The results show that the electron cloud of Cu²⁺ (just like the lattice) can be the electron-pairing medium in high temperature copper oxide superconductors.

As metabolomics is widely used in the study of disease mechanisms, more and more studies have found that metabolites play an important role in the occurrence of diseases. The aim of this study is to investigate the effects and mechanisms of quercetin in high-fat-sucrose diet (HFD)-induced nonalcoholic fatty liver disease (NAFLD) development using nontargeted metabolomics. A rat model of NAFLD was established by feeding with a HFD for 30 and 50 days. Results indicated quercetin exhibited hepatoprotective activity in HFD-induced NAFLD rats in 30 days by regulating fatty acids related metabolites (adrenic acid, etc.), inflammation related metabolites (arachidonic acid, etc.), oxidative stress related metabolites (2-hydroxybutyric acid) and other differential metabolites (citric acid, etc.). However, quercetin couldn’t improve NAFLD in 50 days maybe it couldn’t reverse the inflammation condition induced by long-term high-fat diet. These data indicate that dietary quercetin may be beneficial to NAFLD at early stages. Furthermore, combining metabolomics and experimental approaches opens up avenues of effects and mechanisms of drugs for complex diseases.

In this work we present the results obtained with an artificial neural network (ANN) which we trained to predict the expected output of high-order harmonic generation (HHG) process, while exploring a multi-dimensional parameter space. We argue on the utility and efficiency of the ANN model and demonstrate its ability to predict the outcome of HHG simulations. In this case study we present the results for a loose focusing HHG beamline, where the changing parameters are: the laser pulse energy, gas pressure, gas cell position relative to focus and gas cell length. The physical quantity which we predict here using ANN is directly related to the total harmonic yield in a specified spectral domain (20-40 eV). We discuss the versatility and adaptability of the presented method.

It was demonstrated during the past decade that ultra-short intense laser pulse tightly focused deep inside a transparent dielectric generates the energy density in excess of several MJ/cm$^3$. Such energy concentration with extremely high heating and quenching rates leads to unusual solid-plasma-solid transformation paths overcoming kinetic barriers to formation of previously unknown high-pressure material phases, which are preserved in the surrounding pristine crystal. These results were obtained with the pulse of Gaussian shape in space and in time. Recently it was shown that the Bessel-shaped pulse could transform much larger amount of a material and allegedly create even higher energy density than that was achieved with the Gaussian (GB) pulses. Here we present a succinct review of previous results and discuss the possible routes for achieving higher energy density employing the Bessel beams (BB) and take advantage of its unique properties.

Wildland fires are responsible for large socio-economic impacts. Fires affect the environment, damage structures, threaten lives, cause health issues, and involve large suppression costs. These impacts can be mitigated via accurate fire spread forecast to inform the incident management team. We show that a fire forecast system based on a numerical weather prediction (NWP) model coupled with a wildland fire behavior model can provide this forecast. This is illustrated with the Chimney Tops II wildland fire responsible for large socio-economic impacts. The system is run at high horizontal resolution (111 m) over the region affected by the fire to provide a fine representation of the terrain and fuel heterogeneities and explicitly resolve atmospheric turbulence. Our findings suggest that one can use the high spatial resolution winds, fire spread and smoke forecast to minimize the adverse impacts of wildland fires.

Human factors are the most relevant issues contributing to adverse events in obstetrics. Specific training of Crisis Resource Management (CRM) skills (i.e., problem solving and team management, resource allocation, awareness of environment, and dynamic decision-making) are now widespread and are often based on High Fidelity Simulation. In order to be used as a guideline in simulated scenarios, they need to be translated into specific and observable behavioral markers. To this purpose, we developed a set of observable behaviors related to the main elements of CRM in the delivery room. The observational tool was then adopted in a two-days seminar on obstetric hemorrhage where teams working in obstetric wards of six Italian hospitals took part to simulations. The tool was used as guide for the Io and as a peer-to-peer feedback. It was then rated for its usefulness in facilitating the reflection upon one’s own behavior, its ease of use, and its usefulness for the peer-to-peer feedback. The ratings were highly positive, around 4 in a 5-point scale. The CRM observational tool is therefore a useful, quick and easy solution to facilitate the debriefing, the peer-to-peer feedback and, most of all, the transfer of safe behavior from simulation to everyday practice.

Continuous ultrasonic in-situ monitoring for industrial applications is difficult owing to the high operating temperatures in industrial fields. It is expected that ultrasonic transducers consisting of CaBi4Ti4O15(CBT)/Pb(Zr,Ti)O3(PZT) sol-gel composite could be one solution for ultrasonic nondestructive testing (NDT) above 500 C because no couplant is required and CBT has a high Curie temperature. To verify the high temperature durability, CBT/PZT sol-gel composite films were fabricated on titanium substrates by spray coating, and the CBT/PZT samples were tested in a furnace at various temperatures. Reflected echoes with a high signal-to-noise ratio were observed up to 600 C. A thermal cycle test was conducted from room temperature to 600 C, and no significant deterioration was found after the second thermal cycle. To investigate the long-term high-temperature durability, a CBT/PZT ultrasonic transducer was tested in the furnace at 600 °C for 36 h. Ultrasonic responses were recorded every 3 h, and the sensitivity and signal-to-noise ratio were stable throughout the experiment.

Background: Studies employing next-generation sequencing (NGS) show that the oral fungal community (mycobiome) is far more complex than hitherto thought. However, the role of the oral mycobiome in health and disease, including oral carcinogenesis, has not been explored. Objective: To characterize the mycobiome associated with oral squamous cell carcinoma (OSCC). Methods: Tissue biopsies [cases: 25 OSCC; controls: 27 intra-oral fibro-epithelial polyp (FEP)] were collected from oral and maxillofacial units in Sri Lanka. Total DNA was extracted and subjected to sequencing of the fungal ITS2 region using Illumina’s 2x300 bp chemistry. High quality, non-chimeric merged reads were classified to species level using a BLASTN-algorithm with UNITE’s named species sequences as reference. Downstream analyses were performed using QIIME and LEfSe. Results: 364 species representing 160 genera and 2 phyla (Ascomycota and Basidiomycota) were identified, with Candida and Malassezia making up 48% and 11% of the average mycobiome, respectively. However, only 5 species and 4 genera were detected in ≥50% of the samples. The species richness and diversity were significantly lower in OSCC. At the genus level, Candida, Hannaella and Gibberella were overrepresented in OSCC while Alternaria and Trametes were more abundant in FEP. Species-wise, C. albicans, C. etchellsii and Hannaella luteola-like species were enriched in OSCC while Malassezia restricta, Aspergillus tamarii, Alternaria alternate, Cladosporium halotolerans, and Hanseniaspora uvarum-like species were the most significantly abundant in FEP. Conclusions: A dysbiotic mycobiome dominated by C. albicans was found in association with OSCC. Whether this dysbiosis plays a role in oral carcinogenesis warrants further investigation.

Studies on the possible association between bacteria and oral squamous cell carcinoma (OSCC) remain inconclusive, largely due to methodological variations/limitations. The objective of this study was to characterize the species composition as well as functional attributes of the bacteriome associated with OSCC. DNA obtained from 20 fresh OSCC biopsies (cases) and 20 deep-epithelium swabs (matched control subjects) were sequenced for the V1-V3 region using Illumina’s 2x300 bp chemistry. High quality, non-chimeric merged reads were classified to species level using a prioritized BLASTN-algorithm. Downstream analyses were performed using QIIME, PICRUSt, and LEfSe. Fusobacterium nucleatum subsp. polymorphum was the most significantly overrepresented species in the tumors followed by Pseudomonas aeruginosa and Campylobacter sp. Oral taxon 44, while Streptococcus mitis, Rothia mucilaginosa and Haemophilus parainfluenzae were the most significantly abundant in the controls. Functionally, genes involved in bacterial mobility, flagellar assembly, bacterial chemotaxis and LPS synthesis were enriched in the tumors while those responsible for DNA repair and combination, purine metabolism, phenylalanine, tyrosine and tryptophan biosynthesis, ribosome biogenesis and glycolysis/gluconeogenesis were significantly associated with the controls. This is the first epidemiological evidence for association of F. nucleatum and P. aeruginosa with OSCC. Functionally, an “inflammatory bacteriome” is enriched in OSSC.

In the case of long-stator linear drive, unlike rotative drives for which speed or position sensors are a single unit attached to the shaft, these sensors extend along the guideway. The position signals transmitted from maglev vehicle can’t meet the need of the real-time propulsion control in the on-ground inverter power substations. In this paper the design of the propulsion inverter control system with a position estimator for driving long-stator synchronous motor in high speed maglev train is proposed. The experiments have been carried out at the 150m long guideway in O-song test track. To investigate the performance of the position estimator, the propulsion control system with and without the position estimator are compared. The result confirms that the proposed strategy can meet the dynamic property need of propulsion inverter control system for driving long-stator linear synchronous motors

Originally developed to image the shadow region of the central black hole in Sagittarius A* and in the nearby galaxy M87, the Event Horizon Telescope (EHT) provides deep, very high angular resolution data on other AGN sources too. The challenges of working with EHT data have spurred the development of new image reconstruction algorithms. This work briefly reviews the status of the EHT and its utility for observing AGN sources, with emphasis on novel imaging techniques that offer the promise of better reconstructions at 1.3 mm and other wavelengths.

Big data quality is all about ensuring that the huge amounts of data are accurate, reliable, and useful. It is important because decisions made based on this data can affect many things, like business strategies, customer experiences, and even public policies. Many researchers are studying data quality in the context of big data. This study aims to analyze the research trends and patterns within the domain of big data quality. This method reveals hidden themes in large datasets, helping to understand data quality better. The findings show that Latent Dirichlet Allocation (LDA) is effective for topic modeling in big data, highlighting data quality challenges and opportunities. The research identified key trends and effective assessment methods. For researchers, using LDA in a systematic review helps summarize existing studies and find gaps, guiding future research. Practitioners and future researchers get useful direction for managing data quality and improving efficiency and decisions in various industries.

The purpose of this study was to examine how factors that contribute to the service quality (responsiveness, product diversity, price fairness, and tangibles) offered by a sporting goods store on an online shopping mail affect shopping value. We also explore the moderating effects of positive emotions on the relationship between service quality and shopping value. A total of 654 respondents participated in the survey. The SPSS statistical package and smartPLS 4.0 were used to test the research hypotheses as well as to confirm the moderating effect. The study finds that the abovementioned factors that contribute to the quality of service provided by the online sportswear store had a significant effect on shopping value. Shopping value was in turn found to have a significant effect on customer satisfaction. Customer satisfaction was in turn found to have a significant effect on shopping mall loyalty. The study finds that positive emotions do not have a moderating effect when responsiveness and tangibles affect shopping value. When product diversity and price fairness affect shopping value, however, the moderating effect of positive emotions was found. The results provide implications for practitioners who are concerned about improving the quality of service on online shopping malls. The results of this study contribute valuable guidance to marketers seeking to establish delivery-platform service-marketing strategies.

The gut microbiota plays a pivotal role in host metabolism, influencing the production of small metabolites from non-digestible compounds, which can accumulate in tissues and play important role in fatty acids synthesis for improving the meat quality. We investigate the breed-specific differences in longissimus dorsi (LD) muscle fatty acid profile, gut microbiota, and metabolites across the cecum, ileum, and rectum in Chinese Songliao Black pigs (SBP) and commercial Large White × Landrace crossbred pigs (LWLDP) and interactions. Significant correlations highlighting potential microbiota-metabolite interactions that contribute to muscle fatty acid composition. LWLDP pigs exhibited a higher number of significant fatty acids and maintained higher operational taxonomic units (OTUs) in the cecum and rectum, with no differences observed in the ileum between breeds. Firmicutes, Bacteroidetes, Proteobacteria, and Spirochaetes were the predominant phyla across both breeds. Differentially expressed metabolites (DEMs) were more abundant in the cecum and ileum of LWLDP, while rectum showed higher expression in SBP. Integrative analysis identified significant correlations between fatty acids, metabolites, and microbial taxa. DHA was linked to cecal metabolites and rectal microbial families, while saturated and unsaturated fatty acids were associated with different microbes and metabolites. This study demonstrates distinct breed-specific interactions between gut microbiota, metabolites, and fatty acid composition, offering insights into potential microbial interventions to enhance pork quality through fatty acid modulation.

This paper presents an advanced software tool for precise laser beam propagation analysis, focusing on the calculation of the M2 value, a key measure of beam quality. Developed in Python, the software integrates libraries like NumPy, Matplotlib, and SciPy for robust data handling and accurate polynomial fitting. It features a user-friendly interface for easy data input, analysis, and visualization, making it accessible to both professionals and novices. The tool has been rigorously validated against theoretical models (M2=1) and experimental data (showing M2=1.2548 and 1.3166), ensuring high accuracy and reliability. It visualizes beam width data and fitted polynomial curves, aiding in assessing beam propagation characteristics and optimizing laser systems. Future enhancements include additional beam quality metrics, machine learning integration, and cloud-based functionality. This tool significantly advances laser beam analysis, benefiting research and industrial applications by improving performance and efficiency. The software is available at DOI: 10.5281/zenodo.13325911

The study´s goals were to determine the health status of a group of heart transplant recipients (HTR) and their level of physical activity and to compare the health status among them and with a group of healthy sedentary individuals. Fifty-four HTR and eighteen S were assigned to four groups, according to their level of physical activity (determined with The International Physical Activity Questionnaire); patients with a low, a moderate and a high level of physical activity (HTRL, HTRM and HTRH, respectively) and sedentary individuals (S). Participants underwent a basic blood analysis and several tests to assess their cardiovascular, neuromuscular, functional mobility condition and their quality of life. The S and HTRH were very similar in terms of BP, HR and blood analysis while HTRM and HTRL differed from both S and HTRH in these parameters. Regarding the cardiovascular, neuromuscular, functional mobility, and quality of life variables assessed in this study, HTRH showed the best results across all of them, followed by S, HTRM, and HTRL. It is suggested that the weekly level of physical activity of HTR should be high, what might help them to enhance their health and quality of life.

Consumer perception of beef is heavily influenced by overall meat quality, a critical factor in the cattle industry. Genomics has the potential to improve important beef quality traits and identify genetic markers and causal variants associated with these traits by genomic selection (GS), and genome-wide association studies (GWAS) approaches. Transcriptomics, proteomics, and metabolomics provide insights into underlying genetic mechanisms by identifying differentially expressed genes, proteins, and metabolic pathways linked to quality traits, complementing GWAS data. Leveraging these functional genomics techniques can optimize beef cattle breeding for enhanced quality traits to meet high-quality beef demand. This paper provides a comprehensive overview of the current state applications of the omics technologies in uncovering functional variants underlying beef quality complexities. By highlighting the latest findings from GWAS, GS, transcriptomics, proteomics, and metabolomics studies, this work seeks to serve as a valuable resource fostering a deeper understanding of the complex relationships between genetics, gene expression, protein dynamics, and metabolic pathways in shaping beef quality.

This study presents a comparative analysis of indoor air quality (IAQ) across health centers in Arakale, Iju, Owode, FECA, and Oba Ile, Ondo State, Nigeria. Particle count data were analyzed to identify common trends, similarities, and differences in IAQ parameters, with the aim of informing targeted interventions for improving indoor air quality in healthcare settings. The findings reveal consistent positive skewness in particle count distributions, indicating occasional spikes in pollution levels amidst generally lower concentrations. Fine particles in the size range of PC 2.5 were consistently dominant across all locations, emphasizing their significance in IAQ assessment. Similar variability in particle count data suggests comparable levels of fluctuations in IAQ among the health centers. However, variations in PCA patterns highlight unique factors influencing IAQ in specific locations, such as combustion sources and control strategies. Targeted interventions, including enhancing ventilation systems, controlling indoor pollution sources, and promoting smoking cessation programs, are proposed to mitigate health risks associated with indoor air pollution exposure. Ongoing monitoring and collaboration with environmental experts are crucial for assessing IAQ trends and implementing evidence-based interventions to safeguard the health of patients, staff, and visitors in healthcare facilities.

Stormwater runoff from large roads is a major source of pollutants to receiving waters. Porous pavements have been shown to substantially reduce many of these pollutants, but studies are lacking on arterial roads. We sampled typical stormwater pollutants in runoff from sections of an arterial road 9-16 years after installation of three pavement types: control with conventional asphalt, porous asphalt overly, and full-depth porous asphalt. Both types of porous pavements substantially reduced most of the stormwater pollutants measured. Total suspended solids, turbidity, total lead, total copper, and 6PPD-quinone were all reduced by &gt;75%. Total nitrogen, ammonia, total phosphorus, biochemical oxygen demand, total and dissolved copper, total mercury, total zinc, total polycyclic aromatic hydrocarbons, and di-2-ethylhexyl phthalate were all reduced by &gt;50%. Reductions were lower or absent for nitrate, orthophosphate, E. coli, dissolved lead, and dissolved zinc. Most reductions were statistically significant. Many pollutants exceeded applicable water quality standards in the control samples but met them with both types of porous pavement. This study demonstrates that porous overlays and full-depth porous asphalt can provide substantial reductions of several priority stormwater pollutants on arterial roads for many years after installation.

This study investigates the characteristics of formaldehyde (HCHO) concentration and its reduction in newly constructed apartment buildings in Dubai. It addresses the significant health risks of high HCHO levels due to poor ventilation and extensive use of VOC-emitting materials. The research explores the effectiveness of various mitigation strategies, including air purifiers, photocatalyst applications, and window ventilation, in the living room, master bedroom (MBR), Room 1, and Room 2. HCHO concentrations were measured under different conditions: sealed windows, operation of an air purifier with a VOCs filter, and the application of a photocatalyst. The study followed a quantitative approach, recording real-time HCHO levels over 24 hours. Results indicated that sealing windows led to HCHO concentrations surpassing the domestic standard of 0.1 ppm, with the MBR recording the highest concentration at 0.73 ppm. The air purifier showed minimal impact within the first 8 hours but achieved an 18% reduction after 24 hours of operation. Applying a photocatalyst to room surfaces resulted in a 50% reduction in HCHO levels. Ventilation through window openings significantly improved air exchange rates, with the air exchange per hour (ACH) increasing proportionally with window opening size. Smaller rooms with larger window-to-volume ratios, such as Room 1 and Room 2, maintained HCHO concentrations below the WHO standard of 0.1 ppm with partial window openings. The study concludes that window ventilation is the most effective strategy for reducing HCHO concentrations, highlighting the importance of integrating comprehensive ventilation designs in modern residential buildings to ensure healthier indoor environments in Dubai.

Under the wave of technological advancement and industrial upgrading, new productivity is deeply influencing the field of vocational education and promoting fundamental changes in teachers' roles. Modern teachers must not only keep pace with technological development but also master innovative teaching modes and guide students to form correct values. They are gradually evolving from mere knowledge transmitters to guides for learning, stimulators of interest, explorers of in-depth research, and promoters of comprehensive growth. Through interdisciplinary knowledge structures and innovative abilities, combined with advanced tools such as information technology and artificial intelligence, teachers innovate teaching methods to meet students' diverse learning needs and focus on cultivating students' professional skills, comprehensive qualities, and innovative spirits. This multi-dimensional reshaping of roles is not only an inevitable choice for the development of vocational education but also provides important insights for educational reform.

The aging ability of dry white wines has been increasingly recognised. The present work aimed to understand which sensory factors drive their quality evaluation by experienced tasters. Individuals assessed several aesthetic, synthetic, and analytic flavour attributes, using dark tasting glasses. Wines originated from the grape varieties Alvarinho, Arinto, Sauvignon Blanc and Pinot Bianco with a wide range of ages. Basic physical-chemical analysis, browning (Abs 420 nm), elemental composition and a partial volatile fraction were also determined. The overall quality scores were a function of complexity and balance and were negatively influenced by the perception of faultiness. The different ages could be associated with a continuous sensory space characterised by a decreasing perception of freshness and an increase in the mellowed flavours. All wines shared an austere in-mouth perception elicited by their acidity, saltiness, bitterness, smoothness and dryness. Nevertheless, quality scores were similar from the youngest to the oldest-tasted wines (17 years old). The exception was a Sauvignon Blanc wine from a recent vintage that was judged as faulty due to the perception of earthiness. Overall, the tasted wines displayed an unexpected aging ability as demonstrated by the difference between the predicted and real wine ages. To improve the recognition of old wines, the metaphor “mellowed by age” is proposed to describe flavours resulting from beneficial aging instead of “oxidised by age”.

In the digital age, 3D as-built monitoring of structures and buildings is becoming increasingly important. It provides the basis for automated quality control and progress monitoring through as-built and as-planned model- comparisons, as well as 3D modelling for automated repair, refurbishment and reuse in existing construction. Especially for 3D model-based manufacturing processes such as additive manufacturing, efficient as-built monitoring is essen- tial to ensure the quality and accuracy of buildings and products. Therefore, three different 3D scanning devices have been evaluated for 3D as- built monitoring of concrete structures with different characteristics: An indus- trial handheld laser scanner commonly used in automotive and mechanical en- gineering, a mobile device with lidar for commercial public use, and a terrestri- al laser scanner commonly used for surveying. The devices were tested on 3D printed, cast, and assembled structures of different sizes and geometries. The scan results are compared to the as-planned models based on their dimen- sional distances using Cloud-to-Cloud Comparison (C2C). The results show that the applicability is highly dependent on the size, geometric complexity and surface texture of the concrete structures. While small and flat structures can be captured completely and with micrometer accuracy using the handheld industri- al laser scanner, terrestrial laser scanners are suitable for capturing large struc- tures and environments. The handheld, photogrammetry-based mobile device has demonstrated the broadest applicability for concrete structures. The accura- cy and coverage of the point cloud results were respectively high. Therefore, photogrammetry-based scanning with advanced mobile devices is a cost- effective, fast and portable alternative for 3D as-built monitoring and data ac- quisition of a wide range of concrete structures.

Conclusions: The quantitative method provides a large-scale overview of the biometry measurements of an entire practice. Image audits can then be focused on sonographers whose measurements are outliers, avoiding the time, complexity, and expense of auditing those whose measurements fall within the expected range. We encourage commercial software developers to include tools in their ultrasound reporting software to facilitate such quantitative review.

A smart water quality monitoring system based on the Internet of Things (IoT) paradigm was designed to protect water resources from pollution in real-time. Long-range (LoRa) application of the low-power, wide-area networking (LPWAN) concept has become a phenomenon in IoT smart monitoring applications. This study proposes the implementation of a LoRa network in a water quality monitoring system-based IoT approach. The LoRa nodes were embedded with measuring sensors pH, turbidity, temperature, total dissolved solids (TDS), and dissolved oxygen (DO), in the designated water station. It operates at a transmission power of 14 dB and a bandwidth of 125 kHz. The network properties were tested with two different antenna gains of 2.1 dBi and 3 dBi with three different spread factors (SF) of 7, 9, and 12. The water stations were located at Sungai Pantai and Sungai Anak Air Batu, both rivers on the Universiti Malaya campus. Following a dashboard display and K-means analysis of the water quality data received by the LoRa gateway, it was determined that both rivers are Class II B rivers. The results from the evaluation of LoRa performance on the Received Strength Signal Indicator (RSSI), Signal Noise Ratio (SNR), loss packet, and path loss at best were -83 dBm, 7 dB, &lt; 0%, and 64.41 dB, respectively, with a minimum received sensitivity of -129.1 dBm. LoRa has demonstrated its efficiency in an urban environment for smart river monitoring purposes.

Introduction: Agricultural practices significantly influence soil microbial populations and physicochemical properties, which are crucial for crop growth and quality. This study aims to investigate the impact of different agrochemical applications on soil microbial dynamics, soil physicochemical properties, as well as yield and proximate properties of maize. Methods: Carefully gathered topsoil samples at depths ranging from 1 to 15 cm, were transported to Jimma University to cultivate maize. Over a period of up to 120 days, soil and maize samples were collected at specified days to analyze various parameters, including soil pH, microbial populations, as well as nutrient content both in soil and plants. The collected data was statistically analyzed using one-way ANOVA, with a significance level of p < 0.05. Results: The soil bacterial and fungal populations were measured on days 5, 10, 20, 40, 80, and 120. The highest total mesophilic bacterial count (TMBC) was measured in the pots containing compost (G) and the lowest in pots that received macronutrient fertilizers and glyphosates (B) (i.e. 91.8 x 105 and 13.13 x 105 cfu/g of soil, respectively). The highest total mesophilic fungal count (TMFC) was observed in pots containing glyphosates and compost (F) (i.e. 67.25 x 104 cfu/g soil) and again the lowest in pot treated with macronutrient fertilizers and glyphosate (B) (i.e. 3.23 x 104 cfu/g soil). Moreover, the pots treated with macronutrient fertilizers and glyphosate (B), macronutrient fertilizers (A), and micronutrient fertilizers (C) exhibited the lowest levels of Fe and Zn. Furthermore, the pots receiving macronutrient fertilizer combined with glyphosate (B), as well as those receiving macronutrient fertilizers (A) alone had the lowest concentrations of Mn and Cu micronutrients. Finally, in maize the lowest protein, fats, and carbohydrates (g/100g) were found in the pots treated with macronutrient fertilizer combined with glyphosate (B, 2.21 ± 0.2), micronutrient fertilizer (C, 8.57 ± 0.25), and glyphosates only (D, 57.34 ± 0.1). Maize treated with compost (G) showed the highest levels of Fe, Cu, and Zn, while macronutrient fertilizer combined with glyphosate (B) resulted in the lowest content of these micronutrients. Additionally, maize receiving micronutrient fertilizer (C) had the highest concentration of Mn, whereas those treated with glyphosates (D) had the lowest. Conclusions: Significant variations in soil’s mesophilic bacterial and fungal populations, micronutrient levels, and nutritional composition were observed, indicating treatment-related changes. Generally, treatment with micromineral fertilizer combined with glyphosate (B) seemed to deplete the soil while compost treatment improved. Compost-treated soils exhibited the highest mesophilic bacterial and fungal count, as well as Fe and Zn micronutrient concentrations. The use of agrochemicals also had a negative effect on maize yield quality. The fluctuations in the soil parameters underscore the multifaceted effects of agrochemical treatments.

This study explores the public library service evaluation domain through user-generated content on Google Maps, highlighting digital feedback's significant yet underexplored potential in understanding public library patronage across Taiwan's six major cities. Utilizing a mixed-methods research design, this study integrates Google Maps review content analysis with Social Network Analysis to delineate public perceptions and identify areas for service enhancement in public libraries. It innovatively leverages personal experiences extracted from over 60,000 Google Maps reviews to evaluate public library services in cities such as Taipei, New Taipei, Taoyuan, Taichung, Tainan, and Kaohsiung. The research taps into the National Library of Taiwan's National Library Statistics System to provide a robust analysis of library performance and user satisfaction, offering a novel perspective by emphasizing user-centric feedback from Google Maps as a primary data source. This approach provides quantitative data on library usage and geographic distribution and enriches our understanding of the qualitative experiences of library users. In analyzing the keywords from Google Maps reviews of public libraries, we categorize and interpret these under the three core LibQUAL+ dimensions—Affect of Service, Information Control, and Library as Place. The findings expose variances in perceived service quality among the cities, with Kaohsiung and Taichung receiving the highest accolades for service satisfaction. Simultaneously, the study identifies potential areas for improvement, particularly in cities with lower satisfaction ratings like Taipei. This personalized feedback illustrates the intimate relationship between public libraries and their communities, offering invaluable insights for policymakers and library management to enhance service delivery and user experience.

The institutionalization of people with intellectual disabilities has been a common international response across cultures and generations that persists to this day. This chapter recounts its inheritance and manifestation in modern service provision. An institutional mind-set persists among clinicians and managers despite policies that emphasise the rights of persons with intellectual disability and anti-discriminatory practice. Alternative provision is rooted in person-centred practice; with a growing body of evidence for the improved quality of life that results from it. A reflective activity encourages readers to examine a recent case when they were associated with an institutional placement and what alternatives might have been sought. Yet alliances with other professionals, self-advocates and family carers will be needed to effect real and lasting changes in our service cultures and even then, the long shadows of institutional care may still persist.

Researchers are exploring solutions to meet the growing demand for protein due to the expected increase in global population by 2050. Interest in alternative protein sources like insects has risen, driven by concerns about environmental impact and the need for sustainable food production. This study aimed to develop and evaluate the physicochemical properties of soy protein-based burger enriched with insect protein from Alphitobius diaperinus. Three formulations were developed: a control (B0), and burgers with 5% (B5) and 10% (B10) insect protein - Whole Buffalo Powder (WBP). Results showed that adding insect protein decreased the burger analogue's pH. There was observed a clear trend of increasing total lipids and SFA, and decreasing MUFA and PUFA, as the WBP concentration increases from 0% to 10%. No significant differences with increasing WBP concentration in the protein content of the burger analogue, as well as the cooking yield, were noted. The WBP addition had a notable effect on the color change, especially decrease in brightness (L*). It was shown that as the WBP concentration increased, there were no significant differences in the texture profile of the burger analogues. The formulation with 5% WBP concentration was the most acceptable in sensory analysis.

This study investigates how customers’ technological readiness affects service quality and the adoption of self-service banking by developing an empirical model. The model was proposed to explore the relationships between technology readiness, self-service quality, and customer satisfaction. The hypotheses and stability of the model were tested using structural equation modeling. The findings revealed that technology readiness, including the optimism, innovation, and insecurity dimensions, had a significant positive impact on self-service quality. In addition, service quality fully mediated the relationship between technological readiness and customer satisfaction. These results suggest that when customers are ready to embrace and use new technology, their evaluation of service quality is high. Thus, bank managers should drive customer perceptions of the quality of self-service banking by improving their technological readiness through various measures. Furthermore, based on the mediating effect of self-service quality, banks must be aware that improving service quality can enhance customer satisfaction and maintain a competitive advantage.

Amylose content (AC) stands as a pivotal determinant of rice grain quality, primarily governed by the Waxy gene (Wx), with its allelic diversity significantly influencing AC variation. In the current culinary landscape, soft rice varieties, known for their low AC and superior palatability, are particularly sought after by consumers. Notably, many soft japonica rice varieties cultivated in southern China, including the Nangeng series, are characterized by the presence of the Wxmp allele, derived from the ancestral Wxmq allele. While both alleles are associated with reduced AC, there remains a paucity of detailed understanding regarding the interplay between specific functional single nucleotide polymorphisms (SNPs) within these alleles and the overarching rice grain quality. Employing site-directed mutagenesis, we engineered three distinct transgenic rice lines, each harboring either the Wxmp, Wxmq, or Wxb-5c alleles, against the background of the glutinous rice cultivar Nip(wx). This suite of transgenic rice showcased a gradation ingrain transparency inversely correlated to AC, delineating a sequence from Wxmq, signifying the lowest, through Wxmp, to Wxb-5c, indicating the highest. Consequently, this gradation in AC precipitated variations in other rice grain physicochemical attributes, such as the taste value of cooked rice, gel consistency (GC), and starch pasting properties. Furthermore, analyses of gene expression and enzyme activity revealed that the functional SNPs, Ex4-53G/A and Ex5-53T/C, lead to a decline in the GBSSI enzyme activity without affecting expression levels. These findings underscore the potential of harnessing these SNPs in breeding programs aimed at developing soft rice varieties endowed with enhanced culinary qualities.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

Abstract Introduction: Poor structural quality of health facilities for tuberculosis (TB) diagnosis and treatment contributes to unfavorable health outcomes among TB patients. Improving the quality of healthcare services helps to avert TB-related morbidity. Despite these facts, the level of structural quality of health facilitieSs to deliver TB services is not in line with what the national TB and leprosy program (NTLP) recommends. Hence, the present study was conducted to assess the structural quality of health facilities to deliver quality TB services to TB patients among public health facilities in the Sidama region.Objectives: To determine the quality of the structural domain of TB services at public health facilities in the Sidama region of southern Ethiopia.Methods: An institution-based cross-sectional study was conducted from June to July 2023 among randomly selected public health facilities in the Sidama region. We included 40 randomly selected public health facilities that delivered TB services in the study area. Data was collected by experienced data collectors using facility audits, clinical observation checklists, structured questionnaires, and in-depth interviews. An Open Kit Mobile (ODK) application was used to collect data and exported to SPSS version 26. All statistical analysis was done using SPSS version 26.Results: The overall mean quality score for the structural dimension was 50.25 among the 40 health facilities audited in the study area.Conclusion: The quality of TB services regarding structural dimensions was poor in the study area. Therefore, any strategies must give careful attention to increasing the comprehensive structural dimension of quality TB services.

The agricultural sector is amidst an industrial revolution driven by the integration of sensing, communication, and artificial intelligence (AI). Within this context, the internet of things (IoT) takes center stage, particularly in facilitating remote livestock monitoring. Challenges persist, particularly in effective field communication, adequate coverage, and long-range data transmission. This study focuses on employing LoRa communication for livestock monitoring in mountainous pastures in the north-western Alps in Italy. The empirical assessment tackles the complexity of predicting LoRa path loss attributed to diverse land-cover types, highlighting the subtle difficulty of gateway deployment to ensure reliable coverage in real-world scenarios. Moreover, the high expense of densely deploying end devices makes it difficult to fully analyze LoRa link behavior, hindering a complete understanding of networking coverage in mountainous environments. This study aims to elucidate the stability of Lora link performance in spatial dimensions and ascertain theextent of reliable communication coverage achievable by gateways in mountainous environments. Additionally an innovative deep learning approach was proposed to accurately estimate path loss across challenging terrains. Remote sensing contributes to land-cover recognition, while Bidirectional Long Short-Term Memory (Bi-LSTM) enhances the path loss model’s precision. Through rigorous implementation and comprehensive evaluation using collected experimental data, this deep learning approach significantly curtails estimation errors, outperforming established models. Our results demonstrate that our prediction model outperforms established models with a reduction in estimation error to less than 5dB, marking a 2X improvement over state-of-the-art models. Overall, this study signifies a substantial advancement in IoT-driven livestock monitoring, presenting robust communication and precise path loss prediction in rugged landscapes.

Background: The study aimed to investigate the association between environmental tobacco smoke exposure and the risk of wheezing among rural and urban preschool children in Mpumalanga province, South Africa, an area associated with poor air quality. Methods: In this study, parents/caregivers of preschool children (n=3145) completed a modified International Study of Asthma and Allergies in Childhood (ISAAC) questionnaire. Data were analysed using multiple logistic regression models. Results: The overall prevalence of Wheeze ever was 15.14%, with a higher prevalence in urban pre-schoolers than rural pre-schoolers (20.71% vs 13.30 %, P<0.000). Moreover, the total prevalence of asthma ever was 2.34%. The prevalence was greater in urban pre-schoolers than in rural pre-schoolers (3.92% vs 1.81%, P<0.001). In the final adjusted model, both urban and rural area children who lived with one or more people who smoked in the same household (WE: OR 1.44, 95% CI 1.11-1.86) (CW: OR 2.09, 95% CI 1.38-3.16) and (AE: OR 2.49, 95% CI 1.12-5.54) were found to have an increased likelihood of having Wheeze Ever, Current Wheeze and Asthma Ever as compared to those who lived with non-smokers. Conclusions: The implementation of smoking limits and prohibition is crucial in areas that are frequented or utilized by children. Hence, it is imperative for healthcare providers to actively champion the rights of those who do not smoke within the society, while also endorsing legislative measures aimed at curtailing the extent of tobacco smoke exposure.

Climate change, growing world population and increasing food demand require higher yields and adaptability of crops, including spring bread wheat. Modern plant breeding based on achievements of genetics has a significant impact on plant resistance to diseases, climate variability and other factors. Genome wide association studies (GWAS) is one of genetics tools for mining of genome loci associated with economically important traits. In the current study, we applied GWAS to reveal QTL for spike productivity and grain quality using a panel of spring varieties of Triticum aestivum L. bred in different decades of the last century in Russia and Germany. The study has enabled to find new genetic markers associated with grain yield and quality. Studying genetic basis of grain yield and quality by comparison of wheat varieties from different breeding periods, including landraces preserved as the source of valuable genetic diversity for breeding and genetic studies, makes it possible not only to understand selection processes in the past, but also to develop strategies for future breeding work.

In the early 2000s, matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) emerged as a performant and relevant tool for identifying micro-organisms. Since then, it has become practically essential for identifying bacteria in microbiological diagnostic laboratories. In the last decade, it was successfully applied for arthropod identification allowing to distinguish vectors from non-vectors of infectious diseases. However, identification failures are not rare, hampering it widely use. Failure is generally attributed either to the absence of respective counter species MS spectra in the database, or to the insufficient quality of query MS spectra (i.e. lower intensity and diversity of MS peaks detected). To avoid matching errors due to non-compliant spectra, the development of a strategy for detecting and excluding outlier MS profiles became compulsory. To this end, we created MSProfileR, an R package leading to a bioinformatics tool through a simple installation, integrating the control quality system of MS spectra and an analysis pipeline including peak detection and MS spectra comparisons. MSProfileR can also add metadata concerning the sample that the spectra are derived from. MSProfileR has been developed in the R environment and offers a user-friendly web interface using the R Shiny framework. It is available on Microsoft Windows as a web browser application by simply navigation using the link of the package on the Github. MSProfileR is therefore accessible to non-computer specialists and is freely available to the scientific community. We evaluated MSProfileR using two datasets including exclusively MS spectra from arthropods. In addition to coherent sample classification, outlier MS spectra were detected in each dataset confirming the value of MSProfileR.

This study investigated the anatomical characteristics and pulp quality of tapped Styrax sumatrana wood to facilitate its further utilization. The transverse surface of the tapped S. sumatrana was light or greyish brown in the sapwood and reddish brown in the heartwood. The resin canals of the tapped wood were formed along the growth rings at the boundaries between the heartwood and sapwood. Furthermore, microscopic analyses revealed an irregular outline and rounded epithelial cells at the edges of the intercellular traumatic resin canal (TC). Approximately 8–16 epithelial cells surrounded the resin canals. The fibers in the tapped S. sumatrana were generally thin-walled, whereas those near the TC were thick-walled. Moreover, S. sumatrana were diffuse-porous and exhibited intermediately distinct or indistinct growth ring boundaries. The vessels were mainly in radial multiples and clusters of 3–5. In addition, they showed a diagonal-to-radial pattern arrangement and a few tangential bands. Deposits were observed in some vessels in the tapped part but were absent in the untapped part. The fiber length of the tapped S. sumatrana wood was classified as moderate to extensive and categorized as 2nd grade pulp quality. Finally, the cell walls were classified as thin to moderate.

With end-to-end encryption for video streaming services becoming more popular, network administrators face new challenges in preserving network performance and user experience. Video ads may cause traffic congestion and poor Quality of Experience. Because of the natural variation in user interests and network situations, traditional algorithms for increasing QoE may face limitations. To solve this problem, we suggest a novel method that uses user facial emotion recognition to deduce QoE and study the effect of ads. We use open-access Face Emotion Recognition (FER) datasets and extract facial emotion information from actual observers to train machine learning models. Participants were requested to watch ad videos and provide feedback, which will be used for comparison, training, testing, and validation of our suggested technique. Our tests show that our approach beats the ITU-T P.1203 standard in terms of accuracy by 37.1%. Our method provides a hopeful answer to the problem of increasing user engagement and experience in video streaming services.

The aim of the study is to explore how sharing status updated and receiving Likes on Facebook, as a form of positive social feedback, correlates with current and perceived changes in Quality of Life (QoL) Sample consisted of 1577 adult Facebook users (76.3% females; 65.9% aged 18-24, 21.9% aged 25-30, 12.3% aged &gt; 30 years old). The study employed a longitudinal approach, collecting Facebook data from adult users over a 12-month period using the Graph API. Data were divided into 12 monthly segments. Two monthly indicators were calculated: the percentage of textual status updates and the average number of Likes per post. Current and perceived changes in Quality of Life (QoL) were administered as self-report measures. The findings indicated a positive correlation between the frequency of textual Facebook posts and the average received Likes. Furthermore, receivign more Likes was positively associated with a higher current QoL, and perceived improvements in QoL correlated with an increase in Likes over time. The study suggests that online positive social feedback, measured through Likes on Facebook, is associated with both current QoL and perceived improvements in QoL among adult Facebook users. This highlights the potential impact of online social interactions on individual well-being.

This study aimed to use spatiotemporal tensor data to measure the level of employment quality in China's provinces and analyzed the magnitude and direction of its influencing factors in the spatiotemporal dimension. Taked 30 provinces, autonomous regions and municipalities directly under the central government in China from 2011 to 2020 as the research object, the employment quality evaluation system was constructed from six dimensions of employment environment, employment status, employability, labor remuneration, social security, and labor relations. The employment quality index data was expressed as a three-order high-dimensional tensor spatio-temporal data form, and the employment quality of China's provinces was measured from the spatio-temporal perspective by using principal tensor analysis, and the visual analysis of the development and change process of employment quality was carried out. The spatial autocorrelation analysis of employment quality was carried out, and the time-space dual fixed effect model of the spatial Dubin model was selected to analyze the direction and magnitude of the influence factors of employment quality on itself and its neighboring provinces. The research showed that: (1) The overall level of employment quality in China was not high and the employment quality varies greatly among provinces, and the employment quality development gap among provinces showed a trend of widening. (2) The development of employment quality in western China was relatively fast, while the development of employment quality in central China showed insufficient stamina. (3) Sichuan Province had a strong radiation effect on the development of employment quality in neighboring provinces, and Beijing and Tianjin had a strong siphon effect on the development of employment quality in neighboring provinces. (4) The level of industrialization and informatization promoted the development of employment quality in China's provinces, while the industrial structure had a significant negative effect on the development of employment quality.

Origanum dictamnus L. (Lamiaceae), a local endemic plant of Crete (Greece), creates polysaccharide-containing subcuticular compartments presenting biological activity against phytopathogenic fungi, and, among others, significantly affecting the fungal cell wall polysaccharides. This field study introduces a fertilization scheme for O. dictamnus, which was developed and refined to optimize yield as well as critical herbal quality aspects. Five fertilization schemes were investigated, based on a polysaccharide-based Integrated Nutrient Management (INM), a mixture of chemical fertilizers and two biostimulants (not algae) via foliar and soil application. Plant growth, together with leaf chlorophyll fluorescence and colour (SPAD meter, DA meter, Chroma Meter) were determined. The leaf content of chlorophyll, three critical antioxidant compounds (carotenoids, flavonoids, phenols) and minerals were also assessed. Considering all three antioxidants together, the enhanced efficiency, non-toxic, water-soluble, polysaccharide-based INM by foliar application was the most stimulatory scheme, playing an important role in plant growth and development. The present field study provides for the first time baseline fertilization data improving key herbal quality features in O. dictamnus and unravels the attainment of high antioxidant properties. The latter may be exploited in favor of its further utilization as raw material for tea preparation, medicinal purposes, natural food flavoring and/or food preservative.

The overuse of chemical fertilisers degrades the soil ecosystem and restricts the natural development of plants. Within the coffee industry, various by-products are produced throughout the process of coffee production and consumption, which are significant in terms of environmental waste. SCG (spent coffee grounds) contain a variety of bioactive compounds that have demonstrated potential applications in various fields. These compounds can enhance soil quality by improving its chemical, physicochemical, physical properties, and biological fertility, ultimately leading to improved plant growth. This study examines the impact of SCG, vermicompost, and chemical fertilisers on the growth of organic red radish (Ravanello Cherry Belle) and soil quality. The experiment, conducted in a greenhouse, tested various concentrations and applications of SCG. Results showed that the SCGT 0.5 gm treatment yielded the highest mean plant length (18.47 cm) and fresh weight (27.54 grammes), while the SCG 10% treatment resulted in the lowest mean plant length (4.54 cm) and fresh weight (0.07 grammes). Vermicompost at 50% concentration produced the highest mean leaf surface area (58.32). These findings suggest the potential of SCG as a sustainable fertiliser alternative, contributing to improved plant growth and soil quality, thus supporting sustainable agricultural practices and a circular economy.

In this study, the hybrid biological ion exchange (BIEX) resin and gravity-driven membrane (GDM) process was employed for the treatment of coloured and turbid river water. The primary objective was to investigate the impact of both physical and chemical cleaning methods on ceramic and polymeric membranes in terms of stabilised flux, flux recovery after physical/chemical cleaning, and permeate quality. To address these objectives, two types of MF and UF membranes were utilised (M1 = polymeric MF, M2 = polymeric UF, M3 = ceramic UF, and M4 = lab-made ceramic MF).Throughout extended operation, the resin functioned initially in the primary ion exchange (IEX) region (NOM displacement with pre-charged chloride) and progressed to a secondary IEX stage (NOM displacement with bicarbonate and sulphate), while membrane flux remained stable. Subsequently, physical cleaning involved air/water backwash with two different flows and pressures, and chemical cleaning utilised NaOH at concentrations of 20 and 40 mM, as well as NaOCl at concentrations of 250 and 500 mg Cl2/L. These processes were carried out to assess flux recovery and identify fouling reversibility. The results indicated an endpoint of 1,728 bed volumes (BV) for the primary IEX region, while the secondary IEX continued up to 6,528 BV. At the end of the operation, DOC and UVA254 removal in the effluent of the BIEX columns were 68% and 81%, respectively, compared to influent water. This was followed by 30% and 57% DOC and UVA254 removal by M4 (ceramic MF). The stabilised flux remained approximately 3.8 – 5.2 LMH both before and after the cleaning process, suggesting that membrane materials do not play a pivotal role. The mean stabilised flux of polymeric membranes increased after cleaning, whereas that of ceramics decreased. Enhanced air–water backwash flow and pressure resulted in increased removal of hydraulic reversible fouling, which was identified as the dominant fouling type. Ceramic membranes exhibited higher removal of reversible hydraulic fouling than polymeric membranes. Chemical cleaning had a low impact on flux recovery; therefore, we recommend solely employing physical cleaning.

Background: Catheter ablation (CA) benefits atrial fibrillation (AF) patients with heart failure (HF). Brain natriuretic peptide (BNP), a marker of left-ventricular pressure load, may serve as a potential surrogate for predicting quality of life (QOL) in broader range of patients. Methods: Within the multicenter KiCS-AF registry, 491 AF patients underwent CA without clinical HF (e.g. documented history of HF, left ventricular ejection fraction ≤40%, or BNP levels ≥100 pg/mL). Participants, aged 61±10 years, were categorized by baseline BNP quartiles. Atrial Fibrillation Effect on QualiTy-of-Life (AFEQT) questionnaire assessments were assessed at baseline and 1 year. Results: Lower baseline BNP correlated with reduced AFEQT scores. Post-CA, all groups showed significant AFEQT score improvements. Lower BNP group displayed notable enhancements (18.2±1.2, 15.0±1.1, 12.6±1.2, 13.6±1.2, p<0.005), especially in symptom and treatment concern areas. Even those with normal BNP levels (≤18.4 pg/ml) exhibited significant QOL improvements. Comparing PAF and non-PAF groups, the PAF group, especially with higher BNP levels, showed greater AFEQT score improvements. Conclusion: This study establishes BNP as a predictive marker for QOL enhancement in non-HF patients undergoing CA for AF. BNP levels represent AF stages, with individuals in earlier stages, especially within normal BNP levels, experiencing greater QOL improvement.

Multiple sources influence air quality and regional climate in complicated atmospheric emission situations like urban agglomerations. To resolve pollution plumes and source influences in polluted areas, a comprehensive chemical fingerprinting of sources utilizing non-methane hydrocarbons (NMHCs) and the identification of acceptable tracer molecules and emission ratios is required, in contrast to pristine locations, where reliance on a single or a few chemical tracers is frequently sufficient. We have characterized the prevalence of NMHCs fingerprints in the urban areas and quantified the correlation of windspeed with the concentration of these pollutants. eNose sensors and Air quality management stations provide the data to identify the emission sources of such pollutants. Based on our analysis, the average NMHC concentration in 2021 has been recorded 0.424 ppm at point 1 AQMS whereas at point 2 AQMS it was 0.256 ppm. Such outcomes could be attributed to the proximity of emissions sources, the direction and speed of the wind, or both. Moreover, traffic can be a major contributor to pollution levels in any urban area. More research based on a larger dataset is required before definitive conclusions can be drawn, and viable solutions can be proposed.

Background: Caring for individuals with mental disorders poses significant challenges for caregivers, often leading to compromised quality of life and mental health issues such as stress, anxiety, and depression. This study aims to assess the extent of these challenges among caregivers in Greece, identifying which demographic factors influence their well-being. Method: A total of 157 caregivers were surveyed using the SF-12 Health Survey for quality of life assessment and the DASS-21 questionnaire for evaluating stress, anxiety, and depression symptoms. T-tests, Kruskal-Wallis tests, Pearson correlation coefficients, and regression analyses were applied to understand the associations between demographics, quality of life, and mental health outcomes. Results: The study found that caregivers, especially women and younger individuals, faced high levels of mental health challenges. Marital status, educational level, and employment status also significantly influenced caregivers' well-being. Depression was the most significant factor negatively correlating with the mental component of quality of life. The magnitude of burden experienced by caregivers highlighted the urgency for targeted social and financial support, as well as strategic treatment programs that consider caregiver well-being. Conclusions: Caregivers of individuals with mental disorders endure significant stress, anxiety, and depression, influencing their quality of life. Demographic factors such as age, gender, marital status, education, and employment status have notable impacts. Findings emphasize the need for society-wide recognition of caregivers' roles and the creation of comprehensive support and intervention programs to alleviate their burden, particularly in the context of the COVID-19 pandemic.

Ensuring safe, high-quality food is an ongoing priority, yet consumers face heightened risk from foodborne pathogens due to extended supply chains and climate change in food industry. Nanomaterial-based assays are popular and have recently been developed to ensure food safety and high quality. This review discusses strategies for using nanomaterials in colorimetric biosensors. Localized surface plasmon resonance (LSPR) biosensors are commonly utilized for colorimetric biosensing. Several emerging technologies aimed at simple and rapid immunoassays for onsite applications have been introduced in the food industry. In the foreseeable future, field-friendly colorimetric biosensors could be adopted in food monitoring systems. The onsite and real-time detection of possible contaminants and biological substances in food and water is essential to ensure human health safety.

This study presents a comprehensive assessment of indoor particulate matter (PM) concentrations, focusing on PM1, PM2.5, and PM10 in five Primary Health Centers (PHCs): Arakale, Federal College of Agriculture (FECA), Iju, Oba-Ile, and Owode within Akure Local Government Areas in Nigeria. The primary novelty of this research lies in its detailed exploration of the toxicity potential of these PM fractions, providing valuable insights into the local air quality and associated health risks. The study assesses the health implications by calculating the toxicity potential (TP), Relative Risk (RR), Excess Risk (ER), and Attributable Fractions (AF) for cardiopulmonary and lung cancer mortality. The results reveal varying RR values for all-cause mortality, with Arakale showing a slight elevation (RR: 1.061), indicating potential health risks. ER values for cardiopulmonary mortality range from 14.728±7.25 to 19.04±0.38, emphasizing the substantial excess risk associated with long-term PM2.5 exposure. The study also uncovers AF for cardiopulmonary mortality ranging between 11.03±0.31 to 19.22±0.04, underscoring the significant contribution of PM to cardiovascular and respiratory health risks. Similarly, AF for lung cancer mortality ranges from 10.03±0.012 to 17.13±0.10, highlighting the substantial association between PM2.5 exposure and lung cancer risk. These findings underscore the urgent need for targeted air quality management strategies and public health interventions in the studied locations to mitigate the heightened health risks associated with particulate matter pollution. The calculated RR, ER, and AF values offer crucial insights into the complex relationship between PM exposure and adverse health outcomes, providing a foundation for informed decision-making and future research endeavors.

Air quality is one of the most concerning problems in major industrialized cities in the world. Prediction of future air quality is highly relevant to public health. In some big cities, multiple air quality measurement stations are deployed at different locations to monitor air pollutants, such as NO2, CO, PM 2.5 and PM 10, over time. At every monitoring time stamp t, we observe one station×feature matrix xt of the pollutant data, which represents a spatio–temporal process. Traditional methods on prediction of air quality typically use data from one station or can only predict a single pollutant (such as PM 2.5) at a time, which ignores the spatial correlation among different stations. Moreover, the air pollution data are typically highly nonstationary, We propose a de-trending graph convolutional LSTM (long short term memory) to continuously predict the whole station×feature matrix in the next 1 to 48 hours, which not only captures the spatial dependency among multiple stations by replacing an inner product with convolution, but also incorporates the de-trending signals (transform a nonstationary process to a stationary one by differencing the data) into our model. Experiments on the air quality data of the city Chengdu and multiple major cities in China demonstrate the feasibility of our method and show promising results.

Melasma is a common skin disorder of acquired hyperpigmentation that appears commonly on the face. Although asymptomatic, melasma causes psychosocial and emotional distress. This study aimed to assess melasma's severity on people with darker skin types, evaluate the effects of melasma on the Quality of Life (QoL), and establish QoL predictors in affected individuals. This was a cross-sectional analytic study that enrolled 150 patients who were diagnosed with melasma from three private dermatology clinics in Durban, South Africa. The severity of melasma and QoL were measured using a Melasma Area and Severity Index (MASI) score, and Melasma Quality of Life scale (MELASQoL), respectively. The factors associated with impaired QoL were also explored using the multivariate method and stepwise regression analysis. MASI score of Masi (β = 0.209, t = 2.628, p < .010), involvement of cheeks (β = -0.268, t = -3.405, p <.001), level of education (β = -0.159, t = -2.029, p =.044) and being menopausal (β = -0.161, t = -2.027, p =.045) were found to be predictors of QoL. A regression model to predict MELASQoL given these four predictors was developed. The significance of the equation can allow remote scoring of MELASQoL based on the four variables.

Home enteral nutrition (HEN) is recommended for patients with nutritional requirements who can stay in the familiar environment. HEN guidelines recommend assessing health-related quality of life (HRQoL) to evaluate the effect of the treatment. NutriQoL® is a specific questionnaire developed to assess HRQoL in patients receiving HEN and validated in Spanish population. An observational, descriptive, and prospective study was carried out in two Spanish hospitals to describe the evolution of HRQoL, nutritional and health status in patients receiving HEN in routine clinical practice. Fifty-seven patients participated in the study, of whom 36 were followed-up after their inclusion. Most of them were at risk or moderate malnutrition (61.1%) or showed severe malnutrition (27.8%) at baseline. Patients with HEN showed an overall good HRQoL with a mean basal NutriQoL® score of 69.4, which increased to 74.3 after 12 months of follow-up; fifteen patients showed a clinically significant difference (≥4 points) after three months. The proportion of at-risk or severely malnourished patients decreased at the end of the follow-up period and, according to the physicians, their health status improved. Additionally, physicians considered useful the HRQoL evaluation in clinical practice. In conclusion, HRQoL is probably related to nutritional status improvement and, thus, should be considered for nutritional evaluation in clinical practice.

(1) Background: The goal of the study was to evaluate psychological tolerance and health-related quality of life (QOL) in head and neck (HN) cancer patients treated with definitive accelerated radiotherapy (DART); (2) Methods: Seventy-six recurrence-free patients eligible for the study, who were treated with DART in the CAIR-2 phase III clinical study (median of follow-up=47 months), completed EORTC QLQ-C30 with H&amp;N35 module, Hospital Anxiety and Depression Scale (HADS) and Visual–Analog Scales (VAS) of pain in HN and the neck / arm area.; (3) Results: The most dominating symptoms measured with QLQ-C30 were: fatigue (44/100), sleeplessness (39/100), financial problems (38/100) and pain (32/100). Within H&amp;N35 the highest scores were reported on the subscales of sticky saliva (60/100), mouth dryness (65/100) and increased intake of painkillers (50/100). Pain (VAS) was reported by 87% (HN area) and 78% (shoulder) of the patients, with a mean score of 3/10. One-third reported depressive mood (HADS≥15 points) with an average score of 12.5/42 p. The depressed group, who smoked more as compared to non-depressed before DART (96% vs 78%) and required steroids treatment (85% vs 58%) during DART, also scored significantly worse on 23 of 35 subscales of QLQ-C30 and H&amp;N35 and experienced more intense pain (VAS). Women, and less advanced patients scored better in several aspects of the quality of life; (4) Conclusions: Patients treated with DART struggle with low quality of life and persisting treatment-related symptoms including constant pain. HNC survivors, especially those, who are depressed, may require additional psychosocial, rehabilitation and medical intervention programs..

The menopausal transition often accompanies distressing manifestations, including vasomotor symptoms, sleep disruptions, and depressive syndrome. Omega-3 fatty acids have emerged as a potential intervention to alleviate these symptoms. This review aimed to comprehensively assess the impact of omega-3 supplementation on vasomotor symptoms, sleep quality, and depression among postmenopausal women. We conducted a systematic search focusing on randomized control trials across the Cochrane Library, Web of Science, PubMed, CINAHL, EMBASE, and SCOPUS databases from inception to August 2023. Among the initial pool of 163 studies, 9 studies met the inclusion criteria and were incorporated into this review. Four studies suggested potential benefits of omega-3 intake for improving hot flashes and night sweats. Sleep quality outcomes displayed heterogeneity across the studies. Incorporating diverse scales such as the Hamilton Depression Rating Scale-21, the Patient Health Questionnaire depression scale, and Generalized Anxiety Disorder-7 for depression outcomes, the review found inconclusive evidence on omega-3's impact on depression. Overall, the combined analysis of these studies did not provide substantial evidence to support the efficacy of omega-3 fatty acids in improving vasomotor symptoms, sleep quality, and depression. Further well-designed RCTs with larger participant groups are crucial to validate and generalize these results.

This study takes a two-echelon agricultural products supply chain (APSC) composed of an agricultural product processor (processor) and an agricultural product supermarket (supermarket) as the research object. In order to ensure the stable supply of high-quality agricultural products, this paper considers both fairness concern and corporate social responsibility (CSR), and establishes four Stackelberg game models with or without considering fairness concern and CSR, and obtains the influence mechanism of fairness concern and CSR on bilateral quality efforts in APSC through comparative analysis and numerical analysis. Research shows that the supermarket’s fairness concern can take the role of "profit distribution mechanism", but it is not conducive to improving bilateral quality efforts resulting in the inability to improve market demand, and it is not conducive to improving the utility of the supply chain system and consumer surplus; both members of APSC sharing CSR can not only improve the quality of agricultural products and promote the expansion of market demand, but also can achieve Pareto improvement of both profit of all members and supply chain system. Besides, The CSR shared by both members has a greater impact on bilateral quality efforts decision than the supermarket’s fairness concern, and thus the positive effect of CSR can overcome the negative effect of supermarket’s fairness concern.

The proliferation of physiological sensors opens new opportunities to explore interactions, conduct experiments and evaluate the user experience with continuous monitoring of bodily functions. Commercial devices, however, can be costly or limit access to raw waveform data, while low-cost sensors are efforts-intensive to setup. To address these challenges, we introduce PhysioKit, an open-source, low-cost physiological computing toolkit. PhysioKit consists of (i) a sensor and hardware layer that can be configured in a modular manner per research needs, (ii) a software application layer that enables data acquisition, real-time visualization and machine learning (ML)-enabled signal quality assessment. This also supports basic visual biofeedback configurations and synchronized acquisition for co-located or remote multi-user settings. In a validation study for photo-plethysmography (PPG) sensor with 15 participants, PhysioKit shows strong agreement with research-grade PPG sensors. Furthermore, we report usability survey results from 10 micro-project teams (44 individual members in total) who use PhysioKit for 4-6 weeks, providing insights into its use cases and research benefits. We conclude by discussing extensibility and potential impact of the toolkit on the research community.

Limited scientific evidence shows that alpha lipoic acid (ALA) can induce regression rates of low-grade squamous intraepithelial lesions (LSIL) but the mechanisms of these effects have not been elucidated. To gain a broader insight into its therapeutic potential and mechanisms of action, the effects of 3-month supplementation with 600 mg of ALA on antioxidant- and lipid status param-eters in 100 patients with LSIL were investigated in randomized placebo-controlled study. Obtained results were discussed in terms of patients’ initial metabolic status and diet quality (particularly nutritional intake of antioxidants). Obtained results showed that oxidative status biomarkers were not significantly affected by ALA supplementation. However, serum superoxide dismutase (SOD) activity was positively affected in the subgroup of patients with higher dietary antioxidant intake. Surprisingly, ALA supplementation resulted with small but statistically significant increase of serum low density lipoprotein (LDL) and observed effect was significantly affected by the initial lipid status of participants. Larger studies are necessary to gain additional insights on the clinical significance of ALA as an antioxidant and hypolipemic agent and to optimize its potential application in LSIL treatment.

To achieve user retention through multifactor synergy, Internet enterprises must reduce costs and increase efficiency and sustainable development. In response to the dilemma that Internet compa-nies are experiencing increasingly high user acquisition costs and serious user churn, this paper uses a sample of 46,695 user reviews of nine product series from Xiaomi Ecological Chain. Case studies and qualitative comparative analysis are used to explore the influence mechanisms of quality of experience, brand trust, and brand attachment on users' retention intentions. Our find-ings are as follows. (1) Brand attachment alone is not necessary for high user retention intention, but user perception, cognition, and brand trust are necessary. (2) Quality of experience positively impacts brand trust, attachment, and user retention intention. Therefore, improving user perception and cognition is critical in generating high user retention intention. (3) Five configuration paths can achieve high user retention intention, three configuration paths lead to low user retention intention, and there is an asymmetric relationship between these paths. Among them, the role of quality of experience-driven configuration paths in generating user retention intention is the most prominent. (4) In the substitution relationship between configuration paths, user perception, and cognition can substitute with brand trust and attachment. Our findings have important theoretical and practical implications for revealing the realization paths of high user retention intention in Internet companies and provide a new perspective for future research.

High salinity in soil affects the normal growth and development of crop. MicroRNA171 (miR171) plays a momentous role in plant resistance to adversity stress. The functions of Sly-miR171d and Sly-miR171e on growth of tomato and fruit nutritional quality under salt stress were studied. The results showed that the seed germination and seedling growth of tomato that silencing of Sly-miR171d/e by short tandem target mimic (STTM) were better than those of wild-type (WT). Silencing of Sly-miR171d/e seeds maintained a high germination rate, while WT tomato seeds barely germinated under 50 mM NaCl stress. Under 100 mM NaCl stress, silencing of Sly-miR171d/e increased the expression of their target gene SlGRAS24 with increasing duration of salt stress, while they enhanced the antioxidant activity, reduced reactive oxygen species (ROS) accumulation, and enhanced the salt tolerance of tomato plant by regulating gibberellin (GA) level. Moreover, the preharvest and postharvest fruit nutritional quality under salt stress was also studied, and the results showed that silencing of Sly-miR171d/e increased soluble solids, lycopene, total carotenoids, Vitamin C, organic acids and phenolic substances in tomato fruit. The present study demonstrated that silencing of Sly-miR171d/e enhanced plant salt tolerance through the GA pathway, and improved fruit nutritional quality under salt stress.

The deployment of a manufacturing execution system (MES) holds promising potential in facilitating the accumulation of a substantial amount of inspection data. Low quality levels in discrete manufacturing environments are the result of multi-factor coupling and failure to find quality issues in a timely manner within manufacturing settings may trigger the propagation of defects downstream. Currently, most of the inspection quality methods are direct measurement followed by manual judgment. The integration of deep learning methods provides a feasible way to identify defects in a timely manner, thus improving the acceptance rate of factories. This paper focuses on the design of a data-driven quality prediction and control model around discrete manufacturing characteristics, and use fuzzy theory to evaluate the quality level of production stages. Building Multivariate Long and short-term memory learning hidden quality representations to extract predictions from multi-level inspection data in manufacturing systems. Finally, by validating the data of actual produced water dispensers according to three evaluation indexes, RMSE, MAE, MAPE, the results show that Multivariate Long and short-term memory has better prediction performance.

The use of visual signals in horticulture has attracted significant attention and encompassed a wide range of data types such as 2D images, videos, hyperspectral images, and 3D point clouds. These visual signals have proven to be valuable in developing cutting-edge computer vision systems for various applications in horticulture, enabling plant growth monitoring, pest and disease detection, quality and yield estimation, and automated harvesting. However, unlike other sectors, developing deep learning computer vision systems for horticulture encounters unique challenges due to the limited availability of high-quality training and evaluation datasets necessary for deep learning models. This paper investigates the current status of vision systems and available data in order to identify the high-quality data requirements specific to horticultural applications. We analyse the impact of the quality of visual signals on the information content and features that can be extracted from these signals. To address the identified data quality requirements, we explore the usage of a deep learning-based super-resolution model for generative quality enhancement of visual signals. Furthermore, we discuss how these can be applied to meet the growing requirements around data quality for learning-based vision systems. We also present a detailed analysis of the competitive quality generated by the proposed solution compared to cost-intensive hardware-based alternatives. This work aims to guide the development of efficient computer vision models in horticulture by overcoming existing data challenges and paving a pathway forward for contemporary data acquisition.

Air pollution and the increasing production of greenhouse gases has prompted greater use of renewable energy sources; the EU has set the use of green energy at 32 percent by 2030. With this in mind, in the last 10 years the demand for pellets in Italy has more than doubled making Italy the second largest consumer in Europe. The quality of the pellets burned in stoves is crucial to indoor and outdoor pollution. Among other parameters, moisture and ash are used to classify pellets according to EN ISO 17225:2014. This work involved the analysis of the organic and inorganic fraction of both some finished products on the Italian market and some raw materials (e.g., wood chips) sampled according to the technical standard EN 14778:2011. The analytical results showed the presence of some substances potentially harmful to human health such as formaldehyde, acetone, toluene and styrene for the organic fraction and nickel, lead and vanadium for the inorganic fraction. The chemometric approach showed that it is the inorganic fraction which is most responsible for the diversification of the samples under study. The detection of some substances may be a warning bell about the impact of such materials both for the environment and for the human health.

Growth-preserving instrumentation techniques are utilized in early-onset scoliosis (EOS) cases requiring surgical intervention. Shilla technique corrects the deformity and may reduce the need for surgical treatment with its growth-directing effect. As with other techniques, various prob-lems can be encountered following the administration of the Shilla technique. The aim of this study was to examine the effect of complications encountered with Shilla treatment on correction and growth. Sixteen patients with a follow-up period of at least 1 year who received Shilla growth guidance for EOS were included in the study. No complications occurred in 50% cases and no unplanned surgery was required. Of the remaining 8 patients with postoperative im-plant-related complications (50%), 6 (37.5%) required unplanned surgery; this consequently caused implant failure in the proximal region in 5 cases (31.25%) and deep tissue infection around the implant in 1 case (6.25%). Deformity correction, spine length, and quality-of-life scores significantly improved in EOS through Shilla growth guidance. Although implant-related com-plications were observed and related unplanned surgeries were required with Shilla growth guidance in our patients, these complications did not have a significant negative effect on correc-tion and spine growth.

The study of man-land relationship in urbanization process is the current frontier and focus of international research. How to balance urban development and ecosystem conservation in the Upper Yellow River is a key issue for sustainable development in China. In this study, we evaluated the Lanzhou-Xining urban agglomeration （LXUA）by constructing a multi-dimensional assessment system for urbanization quality and ecosystem services. The efficacy function model, entropy weight method, and Integrated Valuation of Ecosystem Services and Tradeoffs (InVEST) model were used to quantitatively assess the subsystems' state of development. Then, the coupling model (CD) and the coordination degree（CCD）model were used to explore the coupling coordination relationship and spatial-temporal change characteristics of the composite system. The findings indicate that: 1）In 2020, the quality of urbanization in LXUA showed the pattern of "double core". The development of urban centers in each city is insufficient, and the proportion of counties with low-level is too high. 2）Integrated ecosystem services showed an increasing distribution pattern from the northeast to the southwest. Water provision services, soil conservation services and carbon fixation services all showed growth trends. 3）Each county’s composite system was in the run-in stage or highly coupled stage. The subsystems were closely related to each other. 4）The CCD was decreased by 6% between two decades. The number of counties on the verge of disorder was the highest. About 80% of the counties are relatively lagging behind in ecosystem services.