The dual-station Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of single-station dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration.Unmanned aerial vehicles (UAV) equipped with dual-station InSAR, with relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne dual-station InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne dual-station InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision dual-station InSAR imaging and interferometric processing. Height inversion results based on the proposed method is also provided, demonstrating the effectiveness of the proposed method and improving interferometric accuracy at calibration points from 0.66 meters to 0.42 meters.

Communication infrastructures may be partially or completely destroyed due to the natural disasters, especially the disruption of a few critical network devices, leading to the collapse of communication services.To address this issue, we constructed a layered, multi-domain data transmission architecture based on a UAV-assisted resilient network. Initially, the UAV controllers perceived the network status and learning the temporal- spatial characteristics of air-to-ground networks links. Subsequently, we developed a multi-domain routing algorithm based on federated reinforcement distillation, called FedRDR, enhancing the generalization capabilities of routing decision model through the augmentation of training data samples.We conducted simulation experiments, and the results indicate that the FedRDR algorithm has an average communication data volume of approximately 45.3KB between each domain controller and server. Compared to parameter transmission through the federated reinforcement learning algorithm, FedRDR can reduce the amount of transmitted parameters by approximately 29\%. Therefore, the FedRDR routing algorithm promotes knowledge transfer, accelerates the training process of intra-domain intelligent agents, and decreases the communication data volume between domain controllers and servers.

The extraction of roof feature lines is an important foundation for realizing large-scale and batch 3D modeling. However, the current traditional point cloud segmentation algorithms do not have satisfactory results in extracting roof feature lines of Chinese traditional residential buildings. In this paper, taking Jingping Village in Western Hunan as an example, we propose a method that combines multiple algorithms based on slope segmentation of roof patches to extract feature lines. Firstly, VDVI and CSF algorithms are used to extract the building and roof point cloud based on the MVS point cloud. Secondly, according to roof features, village buildings are classified, and 3D roof point cloud is projected into 2D regular grid data. Finally, the roof slope is segmented via slope direction, and internal and external feature lines are obtained after refinement through Canny edge detection and Hough straight line detection. Results reveal that this method effectively extracts feature lines of low-building roofs in traditional villages, with slope-based roof surface segmentation accuracy surpassing 99.6%. This method significantly outperforms the RANSAC algorithm and region segmentation algorithm.

In this paper, the distributed formation tracking control problem of quadrotor unmanned aerial vehicles (UAVs) is considered. Adaptive backstepping technology is used to design flight control schemes for quadrotor UAVs. For the position subsystem, a distributed robust formation tracking control scheme is developed to achieve formation flight of quadrotor UAVs and track the desired flight trajectory. For the attitude subsystem, an adaptive disturbance rejection control scheme is proposed to achieve attitude stabilization during UAV flight under uncertain disturbances. Compared with the existing results, the novelty of this paper is that the proposed formation control scheme does not require the use of the quadrotor model parameters. Finally, a quadrotor UAV swarm system is used to verify the effectiveness of the proposed control scheme.

In this paper, a multirotor UAV platform based on the PX4 ecosystem was discussed, which in combination with the MATLAB Simulink programming environment enables utilization in various aspects of mechatronic engineering education. Extensive testing of the UAV platform control module was performed, in order to enable implementation in engineering education. In the design phase of the educational platform, take-off-the-shelf components were selected and tested, and airframe parts were manufactured using rapid prototyping technologies. The proposed educational platform with four rotors was presented and tested. The learning outcomes of the undergraduate mechatronics professional study program according to the Croatian Qualifications Framework and related to the considered platform are shown. A preliminary framework of laboratory exercises for the field of mechatronic systems control is investigated.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

Capabilities of hovering unmanned aerial vehicles (UAVs) in low-altitude sensing of atmospheric turbulence with high spatial resolution are studied experimentally. The experiment was carried out at the Basic Experimental Observatory of the V.E. Zuev Institute of Atmospheric Optics SB RAS. UAV findings are compared with objective data on the state of the atmosphere that were measured by acoustic anemometers installed at weather towers at altitudes of 4, 10, and 27 m. Profiles of atmospheric turbulence were recorded with three UAVs hovering at the same heights at a distance of 5 m from the anemometers. The behavior of the longitudinal and lateral wind velocity components is studied in the frequency band 0-10 Hz before and after one-minute smoothing, which reveals long turbulent wind gusts. The discrepancy between the UAV and anemometer data is analyzed. It is found that after smoothing, the discrepancy does not exceed 0.5 m/s in 95% cases. This value meets the requirements of the World Meteorological Organization for some applications in wind velocity measurements. The spectral and correlation analysis of the UAV and anemometer measurements is carried out. The profiles of the longitudinal and lateral scales of turbulence are examined based on the UAV data and are found to be in agreement with the anemometer data to a good accuracy.

Rapid advancements in the fifth generation (5G) communication technology and mobile edge computing (MEC) paradigm lead to the proliferation of unmanned aerial vehicles (UAV) in urban air mobility (UAM) networks, which provide intelligent services for diversified smart city scenarios. Meanwhile, the widely deployed internet of drones (IoD) in smart cities also brings up new concerns on performance, security, and privacy. The centralized framework adopted by conventional UAM networks is not adequate to handle high mobility and dynamicity. Moreover, it is necessary to ensure device authentication, data integrity, and privacy preservation in UAM networks. Thanks to characteristics of decentralization, traceability, and unalterability, Blockchain is recognized as a promising technology to enhance security and privacy for UAM networks. In this paper, we introduce LightMAN, a lightweight microchained fabric for data assurance and resilience-oriented UAM networks. LightMAN is tailored for small-scale permissioned UAV networks, in which a microchain acts as a lightweight distributed ledger for security guarantees. Thus, participants are enabled to authenticate drones and verify the genuineness of data that is sent to/from drones without relying on a third-party agency. In addition, a hybrid on-chain and off-chain storage strategy is adopted that not only improves performance (e.g,.latency and throughput) but also ensures privacy preservation for sensitive information in UAM networks. A proof-of-concept prototype is implemented and tested on a Micro Air Vehicle Link (MAVLink) simulator. The experimental evaluation validates the feasibility and effectiveness of the proposed LightMAN solution.

The ever-burgeoning growth of autonomous unmanned aerial vehicles (UAVs) has demonstrated a promising platform for utilization in real-world applications. In particular, UAV equipped with a vision system could be leveraged for surveillance applications. This paper proposes a learning-based UAV system for achieving autonomous surveillance, in which the UAV can be of assistance in autonomously detecting, tracking, and following a target object without human intervention. Specifically, we adopted the YOLOv4-Tiny algorithm for semantic object detection and then consolidated it with a 3D object pose estimation method and Kalman Filter to enhance the perception performance. In addition, a back-end UAV path planning for surveillance maneuver is integrated to complete the fully autonomous system. The perception module is assessed on a quadrotor UAV, while the whole system is validated through flight experiments. The experiment results verified the robustness, effectiveness, and reliability of the autonomous object tracking UAV system in performing surveillance tasks. The source code is released to the research community for future reference.

Recently, the mapping industry has been focusing on the possibility of large-scale mapping from unmanned aerial vehicles (UAVs) owing to advantages such as easy operation and cost reduction. In order to produce large-scale maps from UAV images, it is important to obtain precise orientation parameters. For this, various techniques have been developed and are included in most of the commercial UAV image processing software. For mapping, it is equally important to select images that can cover a region of interest (ROI) with the fewest possible images. Otherwise, to map the ROI, one may have to handle too many images, and commercial software does not provide information needed to select images, nor does it explicitly explain how to select images for mapping. For these reasons, stereo mapping of UAV images in particular is time consuming and costly. In order to solve these problems, this study proposes a method to select images intelligently. We can select a minimum number of image pairs to cover the ROI with the fewest possible images. We can also select optimal image pairs to cover the ROI with the most accurate stereo pairs. We group images by strips, and generate the initial image pairs. We then apply an intelligent scheme to iteratively select optimal image pairs from the start to the end of an image strip. According to the results of the experiment, the number of images selected is greatly reduced by applying the proposed optimal image–composition algorithm. The selected image pairs produce a dense 3D point cloud over the ROI without any holes. For stereoscopic plotting, the selected image pairs were map the ROI successfully on a digital photogrammetric workstation (DPW), and a digital map covering the ROI is generated. The proposed method should contribute to time and cost reductions in UAV mapping.

This paper describes and demonstrates an autonomous robotic team that can rapidly learn the characteristics of environments that it has never seen before. The flexible paradigm is easily scalable to multi-robot, multi-sensor autonomous teams, and is relevant to satellite calibration/validation and the creation of new remote sensing data products. A case study is described for the rapid characterisation of the aquatic environment, over a period of just a few minutes we acquired thousands of training data points. This training data allowed our machine learning algorithms to rapidly learn by example and provide wide area maps of the composition of the environment. Along side these larger autonomous robots two smaller robots that can be deployed by a single individual were also deployed (a walking robot and a robotic hover-board), observing significant small scale spatial variability.

Karst wetlands are being seriously damaged, and protecting it has become an important matter. Karst vegetation is the essential component of wetland and plays an important role in in the ecological functions of wetland ecosystems. Classifying karst vegetation is important for karst wetlands protection and management. This paper addressed to classify karst vegetation in Huixian National Wetland Park, located in China using the improved SegNet Deep-Learning Algorithm and UAV images. This study proposed a method to fuse single-class SegNet models using the maximum probability algorithm for karst vegetation classification, and compared with object-based RF classification and multi-class SegNet classification, respectively. This paper evaluated the performance of multi-class SegNet model and fusion of single-class SegNet model with different EPOCH values for mapping karst vegetation. A new optimized post-classification algorithm was proposed to eliminate the stitching traces caused by SegNet model prediction. The specific conclusions of this paper include the followings:(1) fusion of four single-class SegNet models produced better classification for karst wetland vegetation than multi-class SegNet model, and achieved the highest overall classification accuracy (87.34%); (2) The optimized post-classification algorithm was able to improve prediction accuracy of SegNet model, and it could eliminate splicing traces; (3) The karst wetland vegetation classifications produced by single-class SegNet model outperformed multi-class SegNet model, and improved classification accuracy(F1-Score) between 10%~25%;(4)The EPCOH values and textural feature important impact on karst wetland vegetation classifications. The SegNet model with EPCOH 15 achieved greater classification accuracy(F1-Score) than the model with EPOCH 5 or 10. The textural feature improved improves the capability of the SegNet model for mapping karst vegetation;(5) Fusion of single-class SegNet models and object-based RF model could provide high classifications results for karst wetland vegetation, and both achieved greater 87% overall accuracy.

Rapid assessment of maize yields in smallholder farming system is important to understand its spatial and temporal variability and for timely agronomic decision-support. Imageries acquired with unmanned air vehicles (UAV) offer opportunity to assess agronomic variables at field scale, however, it is not clear if this can be translated into reliable yield assessment on smallholder farms where field conditions, maize genotypes, and management practices vary within short distances. In this study, we assessed the predictability of maize grain yield using UAV-derived vegetation indices (VI), with(out) biophysical variables, in smallholder farms. High-resolution images were acquired with UAV-borne multispectral sensor at 4 and 8 weeks after sowing (WAS) on 31 farmers’ managed fields (FMFs) and 12 nearby Nutrient Omission Trials (NOT), all distributed across 5 locations within the core maize region of Nigeria. The NOTs included non-fertilized and fertilized plots (with and without micronutrients), sown with open-pollinated or hybrid maize genotypes. Acquired multispectral images were post-processed into several three (s) vegetation indices (VIs), normalized difference vegetation index (NDVI), normalized difference red-edge (NDRE), green-normalized difference vegetation index (GNDVI). Biophysical variables, plant height (Ht) and percent canopy cover (CC), were measured with the georeferenced plot locations recorded. In the NOTs, the nutrient status, not genotype, influenced the grain yield variability and outcome. The maximum grain yield observed in NOTs was 9.3 tha^-1, compared to 5.4 tha^-1 in FMF. Without accounting for between- and within-field variations, there was no relationship between UAV-derived VIs and grain yield at 4WAS (r<0.02, P>0.1), but significant correlations were observed at 8WAS (r≤0.3; p<0.001). Ht was positively correlated with grain yield at 4WAS (r=0.5, R²=0.25, p<0.001), and more strongly at 8WAS (r=0.7, R²=0.55, p<0.001), while relationship between CC and yield was only significant at 8WAS. By accounting for within- and between-field variations in NOTs and FMF (separately) through linear mixed-effects modeling, predictability of grain yield from UAV-derived VIs was generally (R²≤0.24), however, the inclusion of ground-measured biophysical variable (mainly Ht) improved the explained yield variability (R² ≥0.62, RMSEP≤0.35) in NOTs but not in FMF. We conclude that yield prediction with UAV-acquired imageries (before harvest) is more reliable under controlled experimental conditions (NOTs), than in actual farmer-managed fields where various confounding agronomic factors can amplify noise-signal within the vegetation canopy.

Phenology is one of the ubiquitous fingerprints of climate change on our ecosystems. Monitoring the spatiotemporal patterns of vegetation phenology is thus critical. A wide range of sensors have been used to monitor vegetation phenology. Sensor point of view and resolution can potentially impact estimates of phenology. We compared three different sensors from three different remote sensing platforms—a UAV mounted RGB camera, an under canopy, upward facing hemispherical camera with R, G and NIR capabilities, and a tower mounted RGB PhenoCam—to estimate spring phenological transition in a mixed-species temperate forest in central Virginia, USA. Our study had two objectives: 1) to compare the above- and below- canopy inference of canopy greenness (green chromatic coordinate and normalized difference vegetation index) and canopy structural attributes (leaf area and gap fraction) by matching under-canopy hemispherical photos with high spatial resolution (0.03 m) drone imagery to find the appropriate spatial coverage and resolution for comparison; 2) to compare how each sensor performed in estimating the temporality of the spring phenological transition. We find that a spatial buffer of 20 m radius for UAV imagery is most closely comparable to under-canopy imagery in this system. Sensors and platforms agree within +/- 5 days of when canopy greenness stabilizes from the spring phenophase into the growing season. This work has implications for paring UAV imagery with both tower-based observation platforms, as well as plot-based studies (e.g. long-term monitoring, existing research networks, permanent plots).

Sea level rise is one of the main factor of risk for the preservation of cultural heritage sites located along the coasts of the Mediterranean basin. Coastal retreat, erosion and storm surges are yet posing serious threats to archaeological and historical structures built along the coastal zones of this region. In order to assess the coastal changes by the end of 2100 under an expected sea level rise of about 1 m, a detailed determination of the current coastline position and the availability of high resolution DSM, is needed. This paper focuses on the use of very high-resolution UAV imagery for the generation of ultra-high resolution mapping of the coastal archaeological area of Pyrgi, near Rome (Italy). The processing of the UAV imagery resulted in the generation of a DSM and an orthophoto, with an accuracy of 1.94 cm/pixel. The integration of topographic data with two sea level rise projections in the IPCC AR5 2.6 and 8.5 climatic scenarios for this area of the Mediterranean, were used to map sea level rise scenarios for 2050 and 2100. The effects of the Vertical Land Motion (VLM) as estimated from two nearby continuous GPS stations located as much as close to the coastline, were included in the analysis. Relative sea level rise projections provide values at 0.30±0.15 cm by 2050 and 0.56±0.22 by 2100, for the IPCC AR5 8.5 scenarios and at 0.13±0.05 cm by 2050 and 0.17±0.22 by 2100, for the IPCC AR5 2.6 scenario. These values of rise will correspond to a potential beach loss between 12.6% and 23.5% in 2100 for RCP 2.6 and 8.5 scenarios, respectively, while during the highest tides the beach will be reduced up to 46.4%. With these sea level rise scenarios, Pyrgi with its nearby Etruscan temples and the medieval castle of Santa Severa will be soon exposed to high risk of marine flooding, especially during storm surges, thus requiring suitable adaptation strategies.

Unmanned Aerial Vehicles (UAVs) severing as the relay is an effective technology method to extend the coverage. It can also alleviate the congestion and increase the throughput, especially applied in UAV networks. However, since the energy of UAVs is limited and the resources in UAV networks are scarce, how to optimize the network delay performance under these constraints should be well investigated. Besides, the relationship among different resources, e.g. power and bandwidth, is coupled which makes the optimization more complex. This article investigates the problem of joint power and bandwidth allocation in UAV backhaul networks, which considers both the delay performance and the resource utilization efficiency. Considering the heterogeneous locations characteristics of different UAVs, we formulate the optimization problem as a Stackelberg game. The relay UAV acts as the leader and extended UAVs act as followers. Their utility functions take both the delay durance and the resource consumption into account. To capture the competitive relationship among followers, the sub-game is proved to be an exact potential game and exists Nash equilibriums (NE). The Stackelberg Equilibrium (SE) is proved afterwards. We utilize a hierarchical learning algorithm (HLA) to find out the best resource allocation strategies, which also reduces the computational complexity. Simulation results demonstrate the effectiveness of the proposed method.

This paper investigates the problem of the optimal arrangement for both UAVs’ caching contents and service locations in UAV-assisted networks based on the context awareness, which considers the influence between users and environment. In the existing work, users within the coverage of UAVs are considered to be served perfectly, which ignores the communication probability caused by line-of-sight (LOS) and non- line-of-sight (NLOS) links. However, the links are related to UAV deployment. Moreover, the transmission overhead should be taken into account. To balance the tradeoff between these two factors, we design the ratio of users’ probability and transmission overhead as the performance measure mechanism to evaluate the performance of UAV-assisted networks. Then, we formulate the objective for maximizing the performance of UAV-assisted networks as a UAV-assisted caching game. It is proved that the game is an exact potential game with the performance of UAV-assisted networks serving as the potential function. Next, we propose the log-linear caching algorithm (LCA) to achieve the Nash equilibrium (NE). Finally, related simulation results reflect the great performance of the proposed algorithm.

The precise prediction of air contaminant dispersion is essential to the air quality monitoring and the emergency management of the contaminant gases leakage incidents in the chemical industry park. The conventional atmospheric dispersion models can seldom give precise prediction due to inaccurate input parameters. In order to improve the prediction accuracy of dispersion model, two data assimilation methods (i.e. one is merely based on the typical particle filter while the other is a combination of particle filter and expectation-maximization algorithm) are proposed to assimilate the UAV observations into the atmospheric dispersion model. Two emission cases are taken into consideration, the difference between which is the different dimensions of state variables. To test the performances of the proposed methods, experiments corresponding to the two emission cases are designed and implemented. The results show that the particle filter can effectively estimate the model parameters and improve the accuracy of model prediction when the dimension of state variables is low. In contrast, when the dimension of state variables becomes higher, the method of particle filter combining expectation-maximization algorithm performs better in the parameter estimation accuracy and warm-up time. Therefore, the data assimilation methods are able to effectively support the air quality monitoring and emergency management in chemical industry parks.

In recent years, UAV-enabled wireless energy transfer (WET) has attracted significant attention for its ability to provide efficient and stable power for ground devices by flexibly navigating 3-dimensional (3-D) space and utilizing the favorable line-of-sight (LoS) channels. Meanwhile, energy beamforming utilizing multiple antennas has been touted as a key technology to substantially enhance the radio frequency (RF)-based WET efficiency by focusing energy beams towards devices in desirable directions. However, energy beamforming design for UAV-enabled WET systems has not been studied, despite its tremendous utility. In this paper, we propose a joint design of the UAV’s altitude and channel statistics based energy beamforming to minimize the overall charging time required for all energy havesting devices (EHDs) to meet their energy demands, while alleviating the additional resources and cost for channel estimation. Unlike previous works that considered only the LoS dominant channel without small-scale fading, we adopt a more general air-to-ground (A2G) Rician fading channel, where the LoS probability as well as the Rician factor depends on the UAV’s altitude. To tackle the highly non-convex and non-linear problem, we first examine a single EHD scenario in order to draw insights by deriving an optimal energy beamformihng in a closed-form, and then devise the efficient methods to jointly design the altitude and energy beamforming for a multiple EHDs scenario. Our numerical results exhibit that the proposed joint design considerably reduce the overall charging time, while benefiting from significantly lowering the computational complexity compared the conventional methods.

Accurate fire severity mapping is essential for understanding the impacts of wildfires on vegetation dynamics in arid savannas. The frequent wildfires in these biomes often cause topkill, where vegetation experiences above-ground combustion, but the below-ground root structures survive, allowing for subsequent regrowth post-burn. Investigating post-fire regrowth is crucial for maintaining ecological balance, elucidating fire regimes, and enhancing the knowledge base of land managers regarding vegetation response. This study examined the relationship between bush fire severity and post-burn coppicing/regeneration events of woody vegetation in the Kalahari Desert of Botswana. Utilizing UAV-derived RGB imagery combined with a Random Forest (RF) classification algorithm, we aimed to enhance the precision of burn severity mapping at a fine spatial resolution. Our research focused on a 1 km2 plot within the Modisa Wildlife Reserve, extensively burnt by the Kgalagadi Transfrontier Fire of 2021. The UAV imagery, captured at various intervals post-burn, provided detailed orthomosaics and canopy height models, facilitating precise land cover classification and burn severity assessment. The RF model achieved an overall accuracy of 79.5% and effectively identified key burn severity indicators, including green vegetation, charred grass, and ash deposits. Our analysis revealed a &gt;50% probability of woody vegetation regrowth in high severity burn areas six months post-burn, highlighting the resilience of these ecosystems. This study demonstrates the efficacy of low-cost UAV photogrammetry for fine scale burn severity assessment and provides valuable insights into post-fire vegetation recovery, thereby aiding land management and conservation efforts in savannas.

We propose a novel unsupervised semantic segmentation method for fast and accurate flood area detection utilizing color images acquired from Unmanned Aerial Vehicles (UAVs). To the best of our knowledge, this is the first fully unsupervised method for flood area segmentation in color images captured by UAVs, without the need of pre-disaster images. The proposed framework addresses the problem of flood segmentation based on parameter-free calculated masks and unsupervised image analysis techniques. First, a fully unsupervised algorithm gradually excludes areas classified as non-flood utilizing calculated masks over each component of the LAB colorspace, as well an RGB vegetation index and the detected edges of the original image. Unsupervised image analysis techniques, such as distance transform, are then applied, producing a probability map for the location of flooded areas. Finally, flood detection is obtained by applying the hysteresis thresholding segmentation. The proposed method is tested and compared with variations, and other supervised methods in two public datasets, consisting of 953 color images in total, yielding high-performance results, with 87.4% and 80.9% overall accuracy and F1-Score, respectively. The results and computational efficiency of the proposed method show that it is suitable for on board data execution and decision-making during UAVs flight.

To accurately and non-destructively monitor the growth of spring wheat in the Hetao Irrigation Area, UAV remote sensing was employed during various fertility stages. Digital image indices from diverse fertilization treatments were calculated and compared with physiological indices to identify the most sensitive digital image indices corresponding to these indices. The study underscored the critical importance of the flowering stage in the growth of spring wheat, thus highlighting the necessity of focusing on this stage. This finding reiterated that the flowering stage was pivotal for spring wheat development in the Hetao Irrigation Area. Several digital image indices, such as GLA, R, G, INT, g, GRVI, MGRVI, RGBVI, EXG, and GRRI, exhibited a high frequency of significant correlations with physiological indices during the four primary reproductive stages of wheat. Consequently, these sensitive digital image indices during the flowering stage can more effectively characterize the physiological indices of spring wheat.

Rapidly and accurately extracting tobacco plant information can facilitate tobacco planting man-agement, precise fertilization and yield prediction. In karst plateau of southern China, tobacco plant identification is affected by large ground undulations, fragmented planting areas, complex and diverse habitats and uneven plant growth. This study took a tobacco planting area in Gui-zhou Province as the research object and used DJI UAVs to collect UAV visible light images. Considering plot fragmentation, plant size, presence of weeds and shadow masking, this area was classified into eight habitats. The datasets of different habitats were constructed to train the U-Net model. The results show that (1) the overall precision, recall, F1-score and IOU of tobacco plant information extraction were 0.68, 0.85, 0.75 and 0.60, respectively. (2) The precision was the highest for the subsurface-fragmented and weed-free habitat and the lowest for the smooth-tectonics and weed-infested habitat. (3) The weed-infested habitat with smaller tobacco plants can cause blurred images, reducing the plant identification accuracy. This study verified the feasibility of the U-Net model for tobacco single-plant identification in complex habitats. Decomposing complex habitats to establish the sample set method is a new attempt to improve crop identification in complex habitats in karst mountainous areas.

Unmanned aerial vehicles (UAV) have emerged as a solution to day to day survey tasks, allowing users to visualize phenomena in real-time. This paper explores the capabilities of UAV or drones in the collection of accurate, geo-tagged data quickly, including photogrammetry software processes to deliver standardized data output. In order to explore the capabilities of UAV, Gatu Township in Centenary, Muzabani District of Zimbabwe was chosen from the national mapping topographic series. This study demonstrates the efficiency of data collection using drones, generate 2D orthomosaics in real time, so that analysts can easily visualize land cover and identify any changes, map and model large areas to produce data for 2D and 3D models. The recent development of innovative optical image processing has further lowered the costs high resolution topographic surveys.

Due to the energetic transition at course, new geological exploration technologies are needed to discover mineral deposits containing critical materials such as lithium (Li). The vast majority of European Li deposits are related to Li–Cs–Ta (LCT) pegmatites. Literature review indicates that conventional exploration campaigns are dominated by geochemical surveys and related exploration tools. However, other exploration techniques must be evaluated namely remote sensing (RS) and geophysics. This work presents the results of the INOVMINERAL4.0 project obtained through alternative approaches to traditional geochemistry that were gathered and integrated into a webGIS application. The specific objectives were to: (i) assess the potential of high-resolution elevation data; (ii) evaluate geophysical methods, particularly radiometry; (iii) establish a methodology for spectral data acquisition and build a spectral library; (iv) compare obtained spectra with Landsat 9 data for pegmatite identification; and (v) implement a user-friendly webGIS for data integration and visualization. Radiometric data acquisition using geophysical techniques effectively discriminated pegmatites from host rocks. The developed spectral library provided valuable insights for space-based exploration. Landsat 9 data accurately identified known LCT pegmatite targets, compared to Landsat 8. The user-friendly webGIS facilitated data integration, visualization, and sharing, supporting potential users in similar exploration approaches.

UAV-captured multispectral imagery was used to characterize and associate Moriche’s palm 1 canopy features with the maturity stage of the corresponding fruits. Deep learning models based on 2 convolutional neural networks (CNN) were trained in order to determine correlations between the 3 photosynthetic radiation of the palms with the fruit. Here, we compare several approaches for feature 4 extraction based on vegetation indices and graph-based models. Also, a comprehensive dataset has 5 been collected and labeled, containing plant data for an entire phenological cycle of the Moriche 6 palms. Experimental results reported an average estimation accuracy of 72%, by using the proposed 7 method in dense forests of the Amazonian region.

For a decade, the studies of dynamic control for unmanned aerial vehicles took a large interest, where drones as a useful technology in different areas were always suffering from several issues like instability-high energy consumption of batteries - inaccuracy of tracking targets. Different approaches are proposed for dealing with the non-linearity issues which present the most important features of this system. This paper describes our focus on the most common control strategies, known as model predictive control MPC, by developing a model based on the sensors embedded in our Tello quadrotor used for indoor purposes. The original controller of Tello quadrotor is supposed to be a slave, where the designed model predictive controller is created in MATLAB and imported to another embedded system, considered as a master; the objective of this model is to track the reference trajectory, almost keeping the stability of the system and ensure the low energy consumption. In the first part, a profound description of the modelling process of a dynamic model for drones is presented, explaining the design of MPC controller with both linear and non-linear strategies built in MATLAB. In the final part, simulation and results are discussed regarding its behaviour and performance, highlighting the MPC model's important role on drones' energy consumption profile.

Unmanned aerial vehicles (UAVs)-based communication system is a promising solution to meet coverage and capacity requirements of future wireless networks. However, UAV-enabled communications is constrained with its coverage, energy consumption, and flying regulations, and the number of works focusing on the sustainability aspect of UAV-assisted networking has been limited in the literature so far. In this paper, we propose a solution to this limitation; particularly, we design a $Q$-learning-based UAV positioning scheme for sustainable wireless connectivity considering key constraints, that are, altitude regulations, non-flight zones, and transmit power. The objective is to find the optimal position of the UAV base station (BS) and minimize the energy consumption while maximizing the number of users covered. Moreover, a weighting mechanism is developed, where the energy consumption and number of users covered can be prioritized according to network/battery conditions. The proposed Q-learning-based solution is compared to the baseline k-means clustering method, where the UAV BS is positioned at the centroid location that minimizes the cumulative distance between the UAV BS and the users. The results demonstrate that the proposed solution outperforms the baseline k-means clustering-based method in terms of the number of users covered while achieving the desired minimization of the energy consumption.

Human populations and natural ecosystems are bound to be exposed to ionizing radiation1from the deposition of artificial radionuclides resulting from nuclear accidents, nuclear devices2or radiological dispersive devices ("dirty bombs"). On the other hand, NORM industries such as3phosphate production or uranium mining, contribute to the on site storage of residuals with enhanced4concentrations of natural radionuclides. Therefore, in the context of the European agreements5concerning nuclear energy, namely the EURATOM (European Atomic Energy Community) Treaty,6monitoring is an essential feature of the environmental radiological surveillance. In this work, we7obtain 3D maps from outdoor scenarios, and complete such maps with measured radiation levels8and with its radionuclide signature. In such scenarios, we face challenges such as unknown and9rough terrain, limited number of sampled locations and the need for different sensors and therefore10different tasks. We propose a radiological solution for scouting, monitoring and inspecting an area of11interest, using a fleet of drones and a controlling ground station. First, we scout an area with a LiDAR12onboard a drone to accurately 3D-map the area. Then, we monitor that area with a Geiger-Muller13sensor at a low-vertical distance from the ground to produce a radiological (heat)map that is overlaid14on the 3D map of the scenario. Next, we identify the hotspots of radiation, and inspect them in detail15using a drone by landing on them, to reveal its radionuclide signature using a CZT sensor. We present16the algorithms used to implement such tasks both at the ground station and on the drones. The three17mission phases were validated using actual experiments in three different outdoor scenarios. We18conclude that drones can not only perform the mission efficiently, but in general they are faster and19as reliable as personnel on the ground

The aim of this research was to test recent developments in the use of Remotely Piloted Aircraft Systems or Unmanned Aerial Vehicles (UAV) to map pasture biomass yield and nutrient status, across a selected range of field sites throughout the rangelands of Queensland. Improved pasture management begins with an understanding of the state of the resource base, UAV based methods can potentially achieve this at improved spatial and temporal scales. This study developed predictive models of both pasture yield and pasture nutrient status. An automated pasture height surface modelling technique was developed, tested and used along with field site measurements of pasture yields, to predict further estimates across each field site. Both prior knowledge and automated predictive modelling techniques were employed to predict pasture yield and nutrition. Pasture height surface modelling was assessed against field measurements using a rising plate meter, results reported correlation coefficients (R2) ranging from 0.2 to 0.4 for both woodland and grassland field sites. Accuracy of the predictive modelling was determined from further field measurements of pasture yield and on average indicated an error of 0.8 t ha-1 in grasslands and 1.3 t ha-1 in mixed woodlands across both modelling approaches. Correlation analyses between measures of pasture quality, acid detergent fibre and crude protein (ADF, CP), and spectral reflectance data indicated the visible red (651 nm) and red-edge (759 nm) regions were highly correlated (ADF R2 = 0.9 and CP R2 = 0.5 mean values). These findings agreed with previous studies linking specific absorption features with grass chemical composition. These results conclude that the practical application of such techniques, to efficiently and accurately map pasture yield and quality, is possible at the field site scale, however further research is needed, in particular further field sampling of both yield and nutrient elements across such a diverse landscape, with the potential to scale up to a satellite platform for broader scale monitoring.

The rapid development of multicopters has led to many security problems. In order to prevent multicopters from invading restricted areas or famous buildings, an Anti-UAV Defense System (AUDS) has been developed and become a research topic of interest. Topics under research in relation to this include electromagnetic interference guns for unmanned aerial vehicles (UAVs), high-energy laser guns, US military net warheads, and AUDSs with net guns. However, these AUDSs use either manual aiming or expensive radar to track UAVs. This paper proposes a dual-axis rotary platform with UAV automatic tracking. The tracking platform uses visual image processing technology to track and lock the dynamic displacement of a UAV. When a target UAV is locked, the system uses a nine-axis attitude meter and laser rangefinders to measure its flight altitude and calculates its longitude and latitude coordinates through sphere coordinates to provide UAV monitoring for further defense or attack missions. Tracking tests of UAV flights in the air were carried out using a DJI MAVIC UAV at a height of 30 meters to 100 meters. It was set up for UAV image capture and visual recognition for tracking under various weather conditions by a thermal imager and a full-color camera respectively. When there was no cloud during the daytime, the images captured by the thermal imager and full-color camera provide a high-quality image recognition result. However, under dark weather, black clouds will emit radiant energy and seriously affect the capture of images by a thermal imager. When there is no cloud at night, the thermal imager performs well in UAV image capture. When the UAV is tracked and locked, the system can effectively obtain the flight altitude and longitude and latitude coordinate values.

Unmanned Aerial Vehicles (UAVs) have gained significant attention in recent times due to their suitability to a wide variety of civil, military and societal missions. Development of an unmanned amphibious vehicle integrating the features of a multi-rotor UAV and a hovercraft is focus of the present study. Components and subsystems of the amphibious vehicle are developed with due consideration on aerodynamic, structural and environmental aspects. Finite element analysis (FEA) on static thrust conditions and skirt pressure are performed to evaluate the strength of structure. For diverse wind conditions and angles of attack (AOA), computational fluid dynamic (CFD) analysis is carried out to assess the effect of drag and suitable design modification is suggested. A prototype is built with a 7 kg payload capacity and successfully tested for stable operations in flight and water-borne modes. Internet of Things (IoT) based water quality measurement is performed in a typical lake and water quality is measured using pH, dissolved oxygen (DO), turbidity and electrical conductivity (EC) sensors. The developed vehicle is expected to meet functional requirements of disaster missions catering to the water quality monitoring of large water bodies.

Precision agriculture is a farm management technology that involves sensing and then responding to the observed variability in the field. Remote sensing is one of the tools of precision agriculture. The emergence of small unmanned aerial vehicles (sUAV) have paved the way to accessible remote sensing tools for farmers. This paper describes the comparison of two popular off-the-shelf sUAVs: 3DR Iris and DJI Phantom 2. Both units are equipped with a camera gimbal attached with a GoPro camera. The comparison of the two sUAV involves a hovering test and a rectilinear motion test. In the hovering test, the sUAV was allowed to hover over a known object and images were taken every second for two minutes. The position of the object in the images was measured and this was used to assess the stability of the sUAV while hovering. In the rectilinear test, the sUAV was allowed to follow a straight path and images of a lined track were acquired. The lines on the images were then measured on how accurate the sUAV followed the path. Results showed that both sUAV performed well in both the hovering test and the rectilinear motion test. This demonstrates that both sUAVs can be used for agricultural monitoring.

Unmanned Aerial Vehicle (UAV) technology has recently experienced increasing development, leading to the creation of a wide variety of autonomous solutions. In this paper a guidance strategy for straight and orbital path following of fixed-wing small UAV is presented. The proposed guidance algorithm is based on a reference Vector Field as desired 16course for the UAV to follow. A Sliding Mode approach is implemented to improve robustness and effectiveness andasymptotic convergence of the aircraft to the desired trajectory in presence of constant wind disturbances is proved according to Lyapunov. The algorithm exploits the banking dynamics and generates reference signals for the inner loop ailerons control. A MATLAB&amp;Simulink® simulation environment is used to verify performance and robustness of the compared guidance algorithms. This high-fidelity model considers the six Degrees-of-Freedom (DoF) whole flight dynamics of the UAV and it is based on experimental flight test data to implement the aerodynamic behavior.

The multi-UAV target search problem is crucial in the field of autonomous Unmanned Aerial Vehicle (UAV) decision-making. The algorithm design of Multi-agent Reinforcement Learning (MARL) methods has become integral to research on multi-UAV target search, due to its adaptability to the rapid online decision-making required by UAVs in complex, uncertain environments. In non-cooperative target search scenarios, targets may have the ability to escape, complicating UAVs' search efforts and hindering the convergence of the MARL algorithm training. This paper investigates the multi-UAV target search problem in scenarios involving static obstacles and dynamic escape targets, modeling the problem within the framework of Decentralized Partially Observable Markov Decision Process. Based on this model, a Spatio-Temporal Efficient Exploration network and a Global Convolutional Local Ascent mechanism are proposed. Subsequently,we introduce a Multi-UAV Escape Target Search Algorithm Based on MAPPO(ETS-MAPPO) for addressing the escape target search difficulty problem. Simulation results demonstrate that the ETS-MAPPO algorithm outperforms five classical MARL algorithms in terms of the number of target searches,the area coverage rate, and other metrics.

The challenging terrain and deep ravines characteristic of mountainous regions often result in slower path planning and suboptimal flight paths for Unmanned Aerial Vehicles (UAVs) when traditional meta-heuristic optimization algorithms are employed. This study investigates the application of an Improved Enhanced Snake Optimizer (IESO) for three-dimensional path planning in a simulated rugged mountainous terrain. The initialization process in the enhanced snake optimizer is refined by integrating the Chebyshev chaotic map. Additionally, a non-monotonic factor is introduced to modulate the "temperature," and a boundary condition is incorporated into the dynamic opposition learning mechanism. These modifications collectively reduce the likelihood of population convergence to local optima during optimization. The feasibility of IESO is validated through time complexity and global convergence analyses. Comparative simulation experiments benchmarked IESO against five state-of-the-art optimization algorithms across test functions and path-planning simulated scenarios. The experimental results indicate that the enhanced algorithm achieves superior optimization precision, faster convergence speeds, and improved quality in the planned trajectories by 30%.

The NW-SE trending dextral strike-slip faults on the north side of the Tian Shan play an important role in accommodating the crustal shortening, which mainly includes the Karatau fault, Talas-Fergana fault, Dzhalair-Naiman fault, Aktas fault, Dzhungarian fault (also named Bolokenu-Aqikekuduk fault) and Chingiz fault. The classic viewpoint is that the strike-slip fault is the adjustment product caused by the difference of the crustal shortening from west to east. Another viewpoint attributes the dextral strike-slip fault to large-scale sinistral shearing. The Alakol Lake Fault is situated along the northern margin of the Dzhungarian Gate, stretching for roughly 150 km from Lake Ebinur to Lake Alakol. Our team utilized aerial photographs, Satellite Stereo-imagery, and field observation to map the distribution of the Alakol Lake fault. Our findings provided evidence supporting the assertion that the fault is a dextral strike-slip fault. In reference to its spatial distribution, Lake Alakol is situated in a pull-apart basin that lies between two major dextral strike-slip fault lines: the Chingiz and Dzhungarian faults. The Alakol Lake Fault serves as a connecting point for these two faults, resulting in the formation of a mega NW-SE dextral strike-slip fault zone. According to our analysis of the dating samples taken from the alluvial fan, as well as our measurement of the displacement of the riser and gully, it appears that the Alakol Lake fault has a dextral strike-slip rate of 0.8-1.5mm/yr. The strike-slip rate of the Alakol Lake fault is comparatively higher than that of the Chingiz fault in the northern region (~0.7 mm/yr), but slower than that of the Dzhungarian fault in the southern (3.2-5 mm/yr). The Chingiz-Alakol-Dzhungarian fault zone shows a gradual decrease in deformation towards the interior of the Kazakhstan platform. We contend that the rate of deformation observed is better explained by the crustal shortening adjustment model, rather than the large-scale sinistral shearing model.

The availability of multi-rotor UAVs with lifting capacities of several kilograms, allows for a new paradigm in atmospheric measurement techniques, i.e. the integration of research-grade sonic anemometers for airborne turbulence measurements. With their ability to hover and move very slowly, this approach yields an unrevealed flexibility compared to mast-based sonic anemometers, for a wide range of boundary layer investigations that require an accurate characterization of the turbulent flow. For an optimized sensor placement, potential disturbances by the propeller-induced flow (PIF), as well as the potential impact of the sensor weight and angular momentum on the flight performance in the case of a boom-mounted sensor, have to be considered.

This research focuses on the development of an automated medication delivery system using Unmanned Aerial Vehicle (UAV) Technology and the Internet of Things (IoT) to support telemedicine and community welfare in the KLU region. The system is designed to improve the quality of medical services and medication management for the community in the area. One of the main challenges faced is how the KLU community responds and accepts automatic medication delivery using UAVs and IoT. To overcome this challenge, this research suggests providing education and training to the community about the benefits and usage of the system, as well as displaying a working simulation of the system to the community.

It is a challenging and meaningful task to carry out drone-based livestock monitoring in high-altitude and cold regions. The purpose of AI is to execute automated tasks and to solve practical problems in actual applications by combining the software technology with the hardware carrier to create integrated advanced devices. Only in this way, the maximum value of AI could be realized. In this paper, a real-time tracking system with dynamic target tracking ability is proposed. It is developed based on the tracking-by-detection architecture using YOLOv7 and DeepSORT algorithms for target detection and tracking, respectively. To address the existing problems of the DeepSORT algorithm, the following two optimizations are made: (1) Optical flow is used to compensate the Kalman filter for improvement of the prediction accuracy; (2) A low-confidence trajectory filtering method is adopted to reduce the influence of unreliable detection on target tracking. In addition, an visual servo controller for the UAV is designed to enable the automated tracking task. Finally, the system is tested using the Tibetan yaks living in the Tibetan Plateau as the tracking targets, and the results reveal the real-time multiple tracking ability and the ideal visual servo effect of the proposed system.

Unmanned Aerial Vehicles (UAVs) in particular multirotors are becoming the {\it de facto} tool for aerial sensing and remote inspection. In large industrial facilities, a UAV can transmit an online video stream to inspect difficult to access structures, such chimneys, deposits and towers. However, the communication range is limited, constraining the UAV operation range. This limitation can be overcome with relaying UAVs placed between the source UAV and the control station, creating a line of communication links. In this work we assume the use of a digital data packet network technology, namely WiFi, and tackle the problem of defining the exact placement for the relaying UAVs that creates an end-to-end channel with maximal delivery of data packets. We consider asymmetric communication links and we show an increase as large as $15$\% in end-to-end packet delivery ratio when compared to an equidistant placement. We also discuss the deployment of such a network and propose a fully distributed method that converges to the global optimal relay positions taking, on average, 1.4 the time taken by a centralized method.

In this study, we propose a scalable deep learning approach to automated phenotyping using UAV multispectral imagery, exemplified by yellow rust detection in winter wheat. We adopt a high granularity scoring method (1 to 9 scale) to align with international standards and plant breeders’ needs. Using a lower spatial resolution (60m flight height at 2.5cm GSD), we reduce the data volume by a factor of 3.4, making large-scale phenotyping faster and more cost-effective while obtaining results comparable to those of the state-of-the-art. Our model incorporates explainability components to optimise spectral bands and flight schedules, achieving top-3 accuracies of 0.87 for validation and 0.67 and 0.70 on two separate test sets. We demonstrate that a minimal set of bands (EVI, Red, and GNDVI) can achieve results comparable to more complex setups, highlighting the potential for cost-effective solutions. Additionally, we show that high performance can be maintained with fewer time steps, reducing operational complexity. Our interpretable model components improve performance through regularisation and provide actionable insights for agronomists and plant breeders. This scalable and explainable approach offers an efficient solution for yellow rust phenotyping and can be adapted for other phenotypes and species, with future work focusing on optimising the balance between spatial, spectral, and temporal resolutions.

Urban ultra-low altitude airspace (ULAA) presents unique challenges for unmanned aerial vehicle (UAV) path planning due to high building density and regulatory constraints. This study analyzes and improves classical path planning algorithms for UAVs in ULAA. Experiments were conducted using A*, RRT, RRT*, and artificial potential field (APF) methods in a simulated environment based on building data from Chengdu City, China. Results show that traditional algorithms struggle in dense obstacle environments, particularly APF due to local minima issues. Enhancements were proposed: a density-aware heuristic for A*, random perturbation for APF, and a hybrid optimization strategy for RRT*. These modifications improved computation time, path length, and obstacle avoidance. The study provides insights into the limitations of classical algorithms and suggests enhancements for more effective UAV path planning in urban environments.

This paper studies the maximum reliability of multi-hop relay UAV, in which UAV provides wireless services for remote users without direct communication link on the ground as a coded cooperative relay. In this paper, the analytical expressions of total power loss and total bit error rate are derived as reliability measures. Firstly, based on the environmental statistical parameters, a LOS probability model is proposed. Then the problem of minimizing the bit error rate of static and mobile UAVs is studied. The goal is to minimize the total bit error rate by jointly optimizing the height, elevation, power and path loss, and subject to the maximum allowable path loss con-straints, transmission power allocation constraints and UAV height and elevation constraints. At the same time the total path loss is minimized to achieve maximum ground communication cov-erage. However, the formulated joint optimization problem is non-convex and generally difficult to solve. Therefore, we decomposed the problem into two subproblems and proposed an effective joint optimization iteration algorithm. Finally, the simulation results are given, and the analysis shows that the optimal height of different reliability measures is slightly different, and using the mobility of UAVs can improve the reliability of communication performance.

Balsam fir trees are a specialty agricultural species that are largely used as Christmas trees. Soil or tissue sampling is seldom performed to assess balsam fir nutrition needs, which can contribute to over or under fertilization and subsequent environmental challenges. Remote sensing to determine the normalized difference vegetation index (NDVI) has had strong relationships with nutrition in other plants. This research aimed to determine whether there is a relationship between NDVI and nutrition in balsam fir. A random sample of 45 trees was selected in autumn of 2021 and then another 70 trees selected in spring of 2022. Soil and needle tissue samples were analyzed for N, P, K, Ca, Mg, S, Fe, Zn, Mn, B, and Cu. An uncrewed aerial vehicle equipped with a multispectral camera was flown over the orchard to determine the NDVI for each tree. Nutrition and NDVI were analyzed for correlations through all sampled trees. Separate correlation analyses were repeated for mature trees (greater than 5 years old) and young trees (less than 5 years old). Soil nutrients N, P, K had a significant relationship with NDVI in autumn sampling. Only N was correlated consistently in both autumn and spring, with R2 of 37% and 33% respectively. Relationships were much stronger when only mature trees were considered, increasing to 60% and 51% respectively. NDVI was found to offer predictive power for tissue N that can be useful to producers to help optimize fertilizer input. However, further work is needed to refine these relationships.

This work aims to develop an autonomous system for the unmanned aerial vehicle (UAV) to land on a moving platform such as the automobile or marine vessels, providing a promising solution for a long-endurance flight operation, a large mission coverage range, and a convenient recharging ground station. Different from most state-of-the-art UAV landing frameworks which rely on UAV’s onboard computers and sensors, the proposed system fully depends on the computation unit situated on the ground vehicle/marine vessel to serve as a landing guidance system. Such novel configuration can therefore lighten the burden of the UAV and computation power on the ground vehicle/marine vessel could be enhanced. In particular, we exploit a sensor fusion-based algorithm for the guidance system to perform UAV localization, whilst a control method based upon trajectory optimization is integrated. Indoor and outdoor experiments are conducted and the result shows that a precise autonomous landing on a 43 X 43 cm platform could be performed.

The escalating global population and subsequent demand for agricultural products have led to a surge in agricultural waste generation, posing significant disposal challenges. Conventional disposal methods such as burning and dumping not only harm the environment but also jeopardize human health and safety. Recognizing the urgent need for sustainable waste management, researchers have increasingly focused on repurposing agricultural plant waste as a valuable resource. This paper presents a comprehensive review of the potential of agricultural plant waste in wealth creation and sustainable development. It highlights the detrimental impacts of current disposal methods and emphasizes the necessity for alternative approaches. By analyzing the physical, mechanical, and chemical properties of plant fibers, particularly cellulose, hemicellulose, and lignin, this review underscores their suitability for diverse applications. Moreover, it explores the emerging trend of utilizing pineapple leaf fiber, a sustainable and lightweight material, in structural applications such as UAV construction. With its exceptional mechanical properties and biodegradability, pineapple leaf fiber holds promise as a viable alternative to traditional materials, contributing to a more sustainable future. In conclusion, this review advocates for a paradigm shift towards embracing agricultural plant waste as a valuable asset for economic prosperity and environmental sustainability. It underscores the importance of continued research and technological advancements to unlock the full potential of agricultural waste in fostering a circular economy and driving sustainable development globally.

Coastal dunes worldwide are increasingly under pressure from the adverse effects of human activities. Therefore, more and more restoration measures are being taken to create conditions that help disturbed coastal dune ecosystems regenerate or recover naturally. However, many projects lack (open-access) monitoring observations needed to signal whether further actions are needed, and hence to learn by doing. This submission presents an open access data set of 37 high-resolution digital elevation models and 24 orthomosaics collected before and after the excavation of five artificial foredune trough blowouts ("notches") in winter 2012/2013 in the Dutch Zuid-Kennemerland National Park, one of the largest coastal dune restoration projects in northwest Europe. These high-resolution data provide a valuable resource for improving understanding of the biogeomorphic processes that determine the evolution of restored dune systems, as well as developing guidelines to better design future restoration efforts with foredune notching.

In recent years, unmanned aerial vehicles (UAVs) have become a valuable platform for many applications, including communication networks. UAV-enabled wireless communication faces challenges in complex urban and dynamic environments. UAVs can suffer from power limitations and path losses caused by non-line-of-sight connections, which may hamper better communication performance. To address these issues, reconfigurable intelligent surfaces (RIS) have been proposed as a helpful tool to enhance UAV communication networks. However, due to the high mobility of UAV, complex channel environments, and dynamic RIS configurations, it is challenging to estimate the link quality of ground users. In this paper, we propose a link quality estimation model using a gated recurrent unit (GRU) to assess the link quality of ground users for a multi-user RIS-assisted UAV-enabled wireless communication system. Our proposed framework uses a time series of user channel data and RIS phase shift information to estimate the quality of the link for each ground user. Simulation results showed that the proposed GRU model effectively and accurately estimates the link quality of the ground users in the RIS-assisted UAV-enabled wireless communication network.

In the past few decades, the use of agricultural waste has been increasing due to the increasing demand for sustainable materials. This paper aims to review the significance of agricultural waste as a type of wealth and its potential as an alternative material in the composite field. It was found that many agricultural wastes had been utilized in various production of ecological products. The review discusses the physical, mechanical, and chemical properties of the natural fibers made from agricultural waste and the use of Pineapple Leaf Fiber Reinforced Composite to manufacture UAVs (Unmanned Aerial Vehicles). The extracted waste fibers’ physical, mechanical, and chemical properties show that these agricultural wastes can produce better advanced composite materials suitable for structural applications. The use of pineapple leaf fiber in Unmanned Aerial Vehicles manufacturing has the potential to revolutionize this industry and contribute to a more sustainable future.

This paper proposes a compact planar Wi-Fi antenna with optimized radiation patterns for small uncrewed aerial vehicle (UAV) applications in both urban and open areas. It is suitable for mounting on the outermost side of the non-metallic wing of small UAVs. It has small dimensions of 16.5 mm (L) by 30.3 mm (W) by 1.6 mm (h), and the measured results of its prototype are in agreement with simulated data. Its impedance bandwidths over the two frequency ranges are 2.11 to 2.58 GHz and 5.06 to 7.5 GHz ( ). At 5.8 GHz, it has stronger radiation below the small UAV to reduce interference from rare-use directions. Its maximum radiations, the directions of the maximum radiation in each elevation plane, are below the UAV and between 14° and 29° from the horizontal plane. At 2.4 GHz, it has quasi-omnidirectional radiation to ensure a stable link in all directions, and its maximum radiations are near the horizontal plane. The optimized radiation patterns at 5.8 and 2.4 GHz can provide more antenna gain when the small UAV flies farther in urban and open areas, respectively. In addition, it has good vertically polarized radiation for long-distance applications.

Quadrotor drones have rapidly gained interest recently. Numerous studies are underway for the commercial use of autonomous drones, and especially the distribution businesses are taking serious reviews on drone delivery services. However, there are still many concerns about urban drone operations. The risk of failures and accidents makes it difficult to provide drone-based services in the real world with ease. There have been many studies that introduced supplementary methods to handle drone failures and emergencies. However, we discovered the limitation of the existing methods. The majority of approaches were improving PID-based control algorithms which is the dominant drone control method. This type of low-level approach lacks situation awareness and the ability to handle unexpected situations. This study introduces an event-based control methodology that takes a high-level diagnosing approach that can implement situation awareness via time-window. While leaving the low-level controller to involve in operating the drone for most of the time in normal situations, our controller operates at a higher level and detects unexpected behaviors and abnormal situations of the drone. We tested our method with real-time 3D computer simulation environments with Unreal Engine[15] and AirSim[31]. We were able to verify that our approach can provide enhanced double safety and better ensure safe drone operations. We hope our discovery to possibly contribute to the advance of real-world drone services in the near future.

A novel adaptive neural network-based fault-tolerant control scheme is proposed for six-degree freedom nonlinear helicopter dynamic. The proposed approach can detect and mitigate sensors' faults in real-time. An adaptive observer-based on neural network (NN) and extended Kalman filter (EKF) is designed, which incorporates the helicopter's dynamic model to detect faults in the navigation sensors. Based on the detected faults, an active fault-tolerant controller, including three loops of dynamic inversion, is designed to compensate for the occurred faults in real-time. The simulation results showed that the proposed approach is able to detect and mitigate different types of faults on the helicopter navigation sensors, and the helicopter tracks the desired trajectory without any interruption.

Remote sensing (RS) is a compulsory component in studying and monitoring ecosystems suffering from the disruption of natural balance, productivity, and degradation. Current study attempted to assess the feasibility of multisource RS for assessing and monitoring mountainous natural grasslands in Armenia. Series of the different spatial resolution RS data (Landsat 8, Sentinel 2, Planet Scope, and multispectral UAV data) were used to obtain various vegetation spectral indices: NDVI, NDWI, GNDVI, GLI, EVI, DVI, SAVI, MSAVI, and GSAVI, and the relationship among the indices were assessed via Spearman correlation method, which shows a significant positive correlation for all cases (p &lt; 0.01). A comparison of all indices shows a significant high correlation between UAV and the PlanetScope imagery. The comparison of UAV, Sentinel and Landsat data show moderate and low significant correlation (p &lt; 0.01) correspondingly. Also, trend analysis was performed to explore their spatial-temporal changes using Mann-Kendall statistical tests (MK, MKKH, MKKY, PW, TFPW), which indicated no significant trend. However, Sen’s slope as second estimator shows decreasing trend. Though the best result received for PlanetScope and Sentinel 2, Sentinel-2 data seem to have better alignment making it a reliable tool for an accurate monitoring of small mountainous grasslands in Armenia.

Accurate and timely prediction of Napa cabbage (Brissica rapa subsp. Perkinensis) fresh weight is crucial for optimizing harvest timing, crop management, and supply chain logistics, contributing to food security and price stabilization. Traditional manual sampling methods are labor-intensive and imprecise. This study addresses this challenge by developing a comprehensive (artificial intelligence) AI-powered model for predicting Napa cabbage fresh weight using unmanned aerial vehicle (UAV)-based multi-sensor data. High-resolution RGB, multispectral, and thermal infrared (TIR) imagery were collected over a Napa cabbage field throughout the 2020 growing season. Various vegetation indices, crop features (vegetation fraction, crop height model), and water stress indi-cators (CWSI) were extracted from the imagery. Three AI algorithms—deep neural network (DNN), support vector machine (SVM), and random forest (RF)—were trained and evaluated, with the DNN model consistently outperforming the others. The DNN model achieved the highest accuracy (R² = 0.86 for training, 0.82 for testing; root mean square error (RMSE) = 0.432 kg for training, 0.465 kg for testing) during the mid-to-late rosette growth stage (DAP 35-42), highlighting this period as crucial for fresh weight estimation due to stable leaf area and well-developed canopy structure. The model tended to underestimate the weight of Napa cabbages exceeding 5 kg, potentially due to limited samples and saturation effects of vegetation indices. However, the overall error rate was less than 5%, demonstrating the feasibility and effectiveness of this approach. Spatial analysis revealed that the model accurately captured the variability in Napa cabbage growth across different soil types and irrigation conditions, particularly reflecting the positive impact of drip irrigation on the sandy loam plot. Bias analysis indicated the DNN model's tendency to overestimate smaller Napa cabbages (2 kg), suggesting areas for future refinement. This study demonstrates the potential of UAV-based multi-sensor data and AI algorithms for accurate and non-invasive prediction of Napa cabbage fresh weight. The developed DNN model offers a promising tool for optimizing harvest timing, improving crop management practices, and en-hancing supply chain efficiency. Future research should focus on refining the model for specific weight ranges and diverse environmental conditions, as well as extending its application to other crops, to further advance precision agriculture and contribute to sustainable food production.

An approach to the implementation of neural network for real-time cryptographic data protection with symmetric keys oriented on embedded systems is presented. This approach is valuable especially for onboard communication systems in unmanned aerial vehicles (UAV) because of suitability to hardware implementation. In this study we evaluate the possibility to build such a system in hardware implementation at FPGA. The proposed integrated neural network approach for real-time cryptographic data protection was based on theoretical foundations of neural network cryptographic data protection, new algorithms and structures of neural network data encryption and decryption, modern hardware components with programmable structure. The development and implementation of the on-board neural network system for cryptographic data protection in real-time are based on the following principles: variable composition of equipment; modularity; conveyorization and spatial parallelism; hardware and software modification and making them suitable for data encryption and decryption. The tabular-algorithmic method for calculation of the scalar product has been improved that makes it possible to perform fast calculation of the scalar product of fixed-point and floating-point input data by bringing them to the largest common order of weights and forming tables of macro-partial products. Components of neural network cryptographic data encryption and decryption have been developed on the processor core supplemented by specialized scalar product calculation modules. The specialized hardware for neural network cryptographic data encryption was developed using VHDL for equipment programming in the Quartus II development environment ver. 13.1 and the appropriate libraries, and implemented on the basis of the FPGA EP3C16F484C6 Cyclone III family.

Drones equipped with thermal cameras have recently become readily available, broadening the possibilities for monitoring wildlife. The European hare (Lepus europaeus) is a nocturnal mammal that is closely monitored in Denmark due to populations declining since the mid-1900s. The limitations of current population assessment methods, such as spotlight counts and hunting game statistics, could be overcome by relying on drone surveys with thermal imaging for population counts. The aim of this study was to investigate the use of a DJI Mavic 2 Enterprise Advanced drone with thermal imaging as a tool for monitoring the Danish hare population. Multiple test flights were conducted over agricultural areas in Denmark in spring 2022, testing various flight altitudes, camera settings, and recording methods. The test flights were used to suggest a method for identifying and counting hare. The applied use of this methodology was then evaluated through a case survey that had the aim of identifying and counting hare over an agricultural area of 242 ha. Hare could be detected with thermal imaging at flight altitudes up to 80 m and it was possible to fly as low as 40 m without observing direct behavior changes. Thermal images taken at these altitudes also provided enough detail to differentiate between species and animal body size proved to be a good species indicator. The case study confirmed the use of thermal imaging based drone surveys to identify hare and conduct population counts, thus, indicating the suggested methodology as a viable alternative to traditional counting methods.

Automation of forest field reference data collection has been an intensive research objective for laser scanning scientists ever since the invention of terrestrial laser scanning more than two decades ago. Recently, it has been proposed that such automated data collection providing both the tree heights and stem curves would require a combination of above-canopy UAV point clouds and terrestrial point clouds. In this study, we demonstrate that an under-canopy UAV laser scanning system utilizing a rotating laser scanner can alone provide accurate estimates of the canopy height and the stem volume for the majority of the trees in a boreal forest. To this end, we mounted a rotating laser scanner based on a Velodyne VLP-16 sensor onboard a manually piloted UAV. The UAV was commanded with the help of a live video feed from the onboard camera of the UAV. Since the system was based on a rotating laser scanner providing varying view angles, all important elements such as treetops, branches, trunks, and ground could be recorded with laser hits. In an experiment including two different forest structures, namely sparse and obstructed canopy, we showed that our system can measure the heights of individual trees with a bias of -20 cm and a standard error of 40 cm in the sparse forest and with a bias of -65 cm and a standard error of 1 m in the obstructed forest. The accuracy of the obtained tree height estimates was equivalent to airborne above-canopy UAV surveys conducted in similar forest conditions. The higher underestimation and higher inaccuracy in the obstructed site can be attributed to three trees with a height exceeding 25 m and the applied laser scanning system VLP-16 that had a limited height measurement capacity when it comes to trees taller than 25 m. Additionally, we used our system to estimate the stem volumes of individual trees with a standard error at the level of 10%. This level of error is equivalent to the error obtained when merging above-canopy UAV laser scanner data with terrestrial point cloud data. Future research is needed for testing new sensors, for implementing autonomous operation inside canopies through collision avoidance and navigation through canopies, and for developing robust methods that work also with more complex forest structure. The results show that we do not necessarily need a combination of terrestrial point clouds and point clouds collected using above-canopy UAV systems in order to accurately estimate the heights and the volumes of individual trees.

Using the Yellow-River-Source National Park (YRSNP) as a study site, an unmanned aerial vehicle (UAV) remote sensing and line transect method was used to investigate the number of wild herbivorous animals and livestock, including the kiang (Equus kiang) and Tibetan gazelle (Procapra picticaudata). A downscaling algorithm was used to generate the forage yield data in YRSNP based on 30 m spatial resolution. On this basis, we estimated the forage–livestock balance, which included both wild animals and livestock, and analyzed the effects of functional zone planning in national parks on the forage–livestock balance in YRSNP. The results showed that the estimates of large herbivore population numbers in YRSNP based on population density in the aerial sample strips, which were compared and validated with statistical data and warm season survey results, indicated that the number of kiangs and Tibetan gazelles in the 2017 cold season was 12900 and 12100, respectively. The number of domestic yaks, Tibetan sheep, and horses was 53400, 76800, and 800, respectively, and the total number of sheep units was 353200. The ratio of the number of large wild herbivores and livestock sheep units was 1:5; Large wild herbivores have different preferences for functional zones, preferring ecological restoration areas consisting mainly of degraded grassland; The grazing pressure indices of the core reserve areas and ecological restoration areas were 0.168 and 0.276, respectively, indicating that these two regions still have high grazing potential. However, the grazing pressure index of the traditional utilization areas was 1.754, indicating that these grasslands are severely overloaded; After the planning and implementation of functional zones, the grazing pressure index of YRSNP was 1.967. Under this measure, the number of livestock was not reduced and the grazing pressure nearly doubled, indicating that forage–livestock conflict has become more severe.

This article proposes the use of a multi-scale and multi-sensor approach to collect and modelling 3D data concerning wide and complex areas in order to obtain a variety of metric information in the same 3D archive, based on a single coordinate system. The employment of these 3D georeferenced products is multifaceted and the fusion or integration among different sensors data, scales and resolutions is promising and could be useful for the generation of a model that could be defined as hybrid. The correct geometry, accuracy, radiometry and weight of the data models are hereby evaluated comparing integrated processes and results from Terrestrial Laser Scanner (TLS), Mobile Mapping System (MMS), Unmanned Aerial Vehicle (UAV), terrestrial photogrammetry, using Total Station (TS) and Global Navigation Satellite System (GNSS) as topographic survey. The entire analysis underlines the potentiality of the integration and fusion of different solutions and is a crucial part of the “Torino 1911” project whose main purpose is mapping and virtually reconstructing the 1911 Great Exhibition settled in the Valentino Park in Turin (Italy).

In this paper, firstly, some questionable formulas and conceptual oversights of previous reduced sigma set unscented transformation (UT) methods are revised through theoretical analysis. Then the revised UT methods based Kalman filters are used in a GPS/INS tightly-coupled system. The Kalman filter flows are the kind of square-root, since the square-root unscented Kalman filters (SRUKFs) can guarantee the stability of the system. By using the reduced sigma set SRUKFs (which contain simplex sigma set square-root unscented Kalman filter (S-SRUKF), spherical simplex sigma set square-root unscented Kalman filter (SS-SRUKF) and minimum sigma set square-root unscented Kalman filter (M-SRUKF)), the computation cost is greatly saved compared with the standard SRUKF, while the accuracy of the GPS/INS tightly-coupled system still maintained. The structure of the GPS/INS tightly-coupled system is in the form of error state, and the time updates of the state and the state covariance of SRUKFs are directly estimated without using UT, thus the computational time is also greatly saved. The pseudo-satellite is introduced to aid the system when the observation information is deficient, for example, when the GPS signal is deficient in the maneuver environment. By using the pseudo-satellite, the optimal performance of the system is guaranteed. Experiment of unmanned aerial vehicle (UAV) showed that the pseudo-satellite aided mechanism worked well.

Landmines, with more than 600 varieties and an estimated 110 million scattered across various regions worldwide, pose a significant threat globally. Heavily found landmines like TM-62M, MON-100, PDM-1, etc., in the recent Russia-Ukraine war, confirm the continued incorporation of metals in munitions. Traditional handheld metal detectors are still state-of-the-art for technical sub-surface demining procedures but are slow, unsafe, and expensive. Drone-based metal detection techniques can provide promising solutions for the rapid and effective detection of landmines; however, their reliability and accuracy remain a concern, as a single miss can cost a life. In our research, we present the results of a comprehensive comparative analysis of three distinct metal detectors: the EM61 Lite, a highly sensitive air-borne metal detector specially designed for UXO detection; the CTX 3030, a traditional handheld all-metal detector; and the ML 3S, a traditional handheld ferrous-only detector. We tested these detectors in a test field containing various inert landmines similar to those currently found in landmine-affected countries, including Ukraine, the US, Russia, and Afghanistan. Our findings highlight the possible challenges and limitations of employing current airborne systems in practical scenarios. Our results also showcase the need for advanced image processing techniques for analyzing airborne metal detector data.

Unmanaged forest ecosystems play a critical role in addressing the ongoing climate and biodiversity crises. As there is no commercial interest in monitoring the health and development of such inaccessible habitats, low-cost assessment approaches are needed. We used a method combining RGB imagery acquired using an Unmanned Aerial Vehicle (UAV), Sentinel-2 data and field surveys to determine the carbon stock of an unmanaged forest in the UNESCO World Heritage Site wilderness area Dürrenstein-Lassingtal in Austria. The entry-level consumer drone (DJI Mavic Mini) and free of charge Sentinel-2 multispectral datasets were used for the evaluation. We merged the Sentinel-2 derived vegetation index NDVI with aerial photogrammetry data and used an orthomosaic and a Digital Surface Model (DSM) to map the extent of woodland in the study area. The Random Forest (RF) Machine Learning (ML) algorithm was used to classify land cover. Based on the acquired field data, the average carbon stock per hectare of forest was determined to be 371.423 ± 51.106 t of CO2 and applied to the ML-generated classification. An overall accuracy of 80.8% with a Cohen’s kappa value of 0.74 was achieved for the land cover classification, while the carbon stock of the living Above-Ground Biomass (AGB) was estimated with an accuracy of -1.0% (± 5.9%). In conclusion, the proposed approach demonstrated that the combination of low-cost remote sensing data and field work can predict above-ground biomass with high accuracy. The results and the estimation error distribution highlight the importance of accurate field data.

Urban tree classification is pivotal in urban planning and management, facilitating informed decision-making processes. In this study, we introduce a novel data presentation method termed Pseudo Tree Crown, designed to enhance the accuracy and efficiency of urban tree classification. Leveraging the latest advancements in artificial intelligence (AI), we employ a state-of-the-art classification scheme, PyTorch, to maximize the accuracy of tree classification. Our results demonstrate a robust classification accuracy of over 95% from high spatial resolution imagery from Unmanned Aerial Vehicle (UAV), underscoring our proposed approach’s effectiveness. Moreover, the adaptability of our method renders it applicable to various study areas, highlighting its versatility and potential for widespread implementation in urban planning and management initiatives.

This paper presents the second stage of a tandem fixed wing unmanned aerial vehicle (UAV) aerodynamic development. In the initial stage, the UAV was optimized analyzing its characteristics only in symmetrical flight conditions. Posted requirements were that both wings should produce relevant positive lift, the initial stall must occur on the front wing first, the center of pressure should be close to the center of gravity, while longitudinal static stability should be in the optimum range. Computational fluid dynamics (CFD) analyses were performed, where applied calculation model was derived from the authors’ previous successful projects. The eight version TW V8 has satisfied all longitudinal requirements. Lateral-directional CFD analyses of V8 showed that the ratio of the lateral and directional stability at the nominal cruising regime was optimal, but both lateral and directional static stabilities were too high. On further development versions the lower vertical tail was eliminated, negative dihedral was implemented on the front wing, and four inverted blended winglets were added. Version TW V14 has largely improved lateral and directional stability characteristics, while their optimum ratio at cruising regime was preserved. Longitudinal characteristics were also well preserved. Maximum lift coefficient and lift-to-drag ratio were increased, compared to the V8.

To address the trajectory tracking issue for quadrotors working under the influence of external disturbances, a control scheme is designed for position and attitude trajectory tracking. Firstly, the quadrotor dynamic model is derived for control design. Secondly, adaptive integral backstepping control (AIBS) is employed in the position loop in which adaptive estimation is used to estimate the upper bounds of disturbances. Subsequently, a new adaptive backstepping fast nonsingular integral terminal sliding mode control (ABFNITSM) is proposed to follow desired Euler angles. The intro-duction of fast nonsingular terminal sliding mode and integral element is to realize fast convergence and accurate tracking. Dead zone technique is applied to minimize estimation errors. Besides, a saturation function is utilized to eliminate chattering phenomenon. Finally, simulation experiments are conducted under the Simulink environment. The proposed control is verified by comparing it with traditional integral terminal sliding mode control (ITSM) and integral backstepping control (IBS).

Precision farming, a labor-saving and highly productive management, is gaining popularity as the number of farmers declines in contrast to the increasing global food demand. However, it requires more efficient crop phenology observation and growth monitoring. One measure is the Leaf Area Index (LAI), which is essential for estimating biomass and yield, but its validation requires destructive field measurements. Remote sensing offers a non-destructive and effective method for ground- and UAV-based field observations. Thus, in this study, a method for indirect estimation of LAI was investigated using ground and UAV observation data. A weekly plant survey was done to measure the plant height, above-ground biomass, and light intensity. Furthermore, images from ground-based and UAV-based cameras were acquired to generate NDVI and the canopy height (CH), respectively. Using the canopy photosynthetic model, derived from Lambert-Beer’s law, the daily biomass was estimated by applying the weekly estimated LAI using CH, and the observed light intensity data as input. The results demonstrated the possibility of quantitatively estimating the daily growth biomass of rice plants, including its spatial variation. The near-real-time estimation method of rice biomass by integrating observation data at fields with numerical models can be applied to the management of major crops.

This paper aims at trying to answer the question of whether a low cost drone equipped with a regular camera can serve as a simple device to estimate the size of objects. Ad-ditionally, it assesses if the accuracy of measurement is good enough for using a drone for measurements, relying solely on GPS position and camera. A review of the literature pertaining to ground object measurements was conducted. The availability of such in-struments was evaluated in terms of purchase and rental costs, the number of instru-ments on the market, and the time to obtain them. The most common measurement methods were considered and their unit costs were reviewed. The cost of professional surveying and measuring equipment was compared to the possibility of using low-cost, non-commercial drones to measure objects and surfaces. The quality of the images ob-tained was compared with high-resolution satellite systems. Is an ordinary drone with a standard camera suitable for length measurement without professional measuring equipment? Should the results be considered only in the category of size estimation?

The effective integration of aerial remote sensing data and ground multi-source data has always been one of the difficulties of quantitative remote sensing. A new monitoring mode is designed which installs the hyperspectral imager on the UAV and places a buoy spectrometer on the river. Water samples are collected simultaneously to obtain in situ assay data of total phosphorus, total nitrogen, COD, turbidity and chlorophyll during data collection. The cross correlogram spectral matching (CCSM) algorithm is used to match the data of the buoy spectrometer with the UAV spectral data to reduce the UAV data noise significantly. An absorption characteristics recognition algorithm (ACR) is designed to realize a new method for comparing UAV data with laboratory data. This method takes into account the spectral characteristics and the correlation characteristics of test data synchronously. It is concluded that the most accurate water quality parameters can be calculated by using the regression method under five scales after the regression tests of multiple linear regression method (MLR), support vector machine method (SVM) and neural network (NN) method. This new working mode of integrating spectral imager data with point spectrometer data will become a trend in water quality monitoring.

Low-cost miniature hyperspectral and thermal cameras onboard lightweight unmanned aerial vehicles (UAV) bring new opportunities for monitoring land surface variables at unprecedented fine spatial resolution with acceptable accuracy. This research applies hyperspectral and thermal imagery from a drone to quantify upland rice growth and water use efficiency (WUE) after biochar application in a Costa Rican dry region. The field flights were conducted over two experimental groups with bamboo biochar and sugarcane biochar amendments and one control group without biochar application. Rice canopy biophysical variables were estimated by inversion of a canopy radiative transfer model on hyperspectral reflectance. Variations in gross primary production (GPP) and WUE across treatments were estimated from the normalized difference vegetation index (NDVI), canopy chlorophyll content (CCC), and evapotranspiration. We found that GPP was increased by 41.9±3.4 % when using bamboo biochar and 17.5±3.4 % when using sugarcane biochar, which was probably due to higher soil moisture in the biochar-amended plots and led to significantly higher WUE by 40.8±3.5 % in bamboo biochar and 13.4±3.5 % in sugarcane biochar. This study demonstrated the use of hyperspectral and thermal imagery from drone to provide indicators for quantifying biochar effects on tropical dry cropland by integrating with ground point samples and physical models.

Due to the convenience of implementing without additional transmitter, radar communication integrated systems using conventional communication signals have become an effective means of monitoring unmanned aerial vehicles and other aircraft. However, the non-ideal radar signal form causes the strong signal to cover the weak signal, and the clutter suppression is required to expose the target. As the target signal is extremely low, and the performance of conventional clutter suppression methods is limited, the residual clutter remains after the time-varying clutter is suppressed, which leads to many false alarm points on the processed RD spectrum. The two-dimensional distribution of these false alarms in range-Doppler is very similar to the target and difficult to be distinguished, which seriously affects the target detection and tracking. To reduce false alarm points and improve the performance of target detection, the difference of spatial-temporal stationarity between target signal and clutter in a short time is discussed in this paper, a radar false alarm suppression method based on target spatial-temporal stationarity is proposed by using the difference of stationarity between target signal and false alarm points in range, Doppler, energy and azimuth. In this algorithm, to ensure the short-time stationarity of the target, the RD spectrum of sub-frames with short time interval is obtained by using the sliding matching filtering method and extract the peak points. Then, the Mahalanobis distance between the peak points of each sub-frame is used to eliminate false alarm points. Finally, false alarm points are further eliminated through the target tracking and retain the real target information, so as to improve the radar target detection performance. The simulation experiments show that this method can eliminate more than 90% false alarms points while maintaining the detection performance of the target. The processing of actual data in the field experiment shows that the after suppression false alarm by this algorithm can obtain more ideal target detection results, and realize the tracking of the UAV and other aircraft track.

Tail-sitters aim to combine the advantages of fixed-wing and rotor-craft, but demand a robust and fast stabilization strategy to perform vertical maneuvers and transitions to and from aerodynamic flight. The research conducted in this work intends to assess the performance of nonlinear control strategies to stabilize the attitude of a X-Vert VTOL aircraft when hovering, comparing existing solutions to applications of Nonlinear Dynamics Inversion (NDI) and its incremental version, INDI. Such controllers are implemented and tuned in simulation in order to stabilize a model of the tail-sitter , complemented by estimation methods that allow to feed back the necessary variables. These estimators and controllers are then implemented in a microcontroller, validating them in a Hardware-in-the-Loop (HITL) scenario, with simple maneuvers in vertical flight. Lastly, the developed control solutions are used to stabilize the aircraft in experimental flight, being monitored by a motion capture system. The experimental results allow to validate the model of the X-Vert and compare the effectiveness of the different control solutions in stabilizing it, with the INDI presenting itself as a more robust control strategy, with better tracking capabilities and less actuator demands.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

The neural network technology for real-time cryptographic data protection with symmetric keys (masking codes, neural network architecture and weights matrix) for unmanned aerial vehicles (UAV) onboard communication systems has been developed. It provides hardware and software implementation with high technical and operational characteristics. The development of neural network technology for real-time cryptographic data protection was performed using an integrated approach based on theoretical foundations of neural network cryptographic data protection, new algorithms and structures of neural network data encryption and decryption, modern element base with the possibility of programming for the structure, and computer-aided design of hardware and software tools. The development and implementation of the on-board system of neural network cryptographic data protection in real-time are based on the following principles: variable composition of equipment; modularity; conveyorization and spatial parallelism; specialization and adaptation of hardware and software to data encryption and decryption. The tabular-algorithmic method of calculating the scalar product has been improved, it provides fast calculation of the scalar product of input data for both fixed and floating-point by bringing to the largest common order of weights and forming tables of macro-partial products for them. Components of neural network cryptographic data encryption and decryption have been developed on the processor core supplemented by specialized scalar product calculation modules. The specialized hardware for neural network cryptographic data encryption was developed using VHDL for equipment programming in the Quartus II development environment ver. 13.1 and the appropriate libraries, and implemented on the basis of the FPGA EP3C16F484C6 Cyclone III family.

Tracking and early identification of suspected cases are essential to control and prevent potential COVID-19 outbreaks. One of the most popular techniques used to track this disease is the use of Infrared cameras to identify individuals with elevated body temperatures. However, they are limited by their inability to be implemented in open public settings such as public parks or even outdoor recreational centers. This limits their ability to effectively track possible COVID-19 patients as open public recreational places such as parks, concert venues and other public venues are hotspots for the spreading of the virus. Other technological solutions such as thermal scanners require an individual to perform the actual testing as they are not individual standalone technologies. This method of testing can potentially cause the transmission of the virus between the tester and the individual getting tested. As can be seen, an alternative solution is essential to solving this issue. In this study, we aim to present the system, design and potential scope of a non-invasive system that can diagnose and identify potential COVID-19 patients using thermal and optical images of the individual using drone technology. The proposed system (COVIDRONE) combines multi-modal machine intelligence, computer vision and real-time monitoring to enable scalable monitoring. The system will also involve the use of machine learning algorithms for better and more accurate diagnosis. We envisage that development of such technologies may help in developing technological solutions to combat infectious disease threats in the future pandemics.

Remote sensing is one of the modern methods that have significantly developed over the last two decades and nowadays provides a new means for forest monitoring. High spatial and temporal resolutions are demanded for accurate and timely monitoring of forests. In this study multi-spectral Unmanned Aerial Vehicle (UAV) images were used to estimate canopy parameters (definition of crown extent, top and height as well as photosynthetic pigment contents). The UAV images in Green, Red, Red-Edge and NIR bands were acquired by Parrot Sequoia camera over selected sites in two small catchments (Czech Republic) covered dominantly by Norway spruce monocultures. Individual tree extents, together with tree tops and heights, were derived from the Canopy Height Model (CHM). In addition, the following were tested i) to what extent can the linear relationship be established between selected vegetation indexes (NDVI and NDVIred edge) derived for individual trees and the corresponding ground truth (e.g., biochemically assessed needle photosynthetic pigment contents), and ii) whether needle age selection as a ground truth and crown light conditions affect the validity of linear models. The results of the conducted statistical analysis show that the two vegetation indexes (NDVI and NDVIred edge) tested here have a potential to assess photosynthetic pigments in Norway spruce forests at a semi-quantitative level, however the needle-age selection as a ground truth was revealed to be a very important factor. The only usable results were obtained for linear models when using the 2nd year needle pigment contents as a ground truth. On the other hand, the illumination conditions of the crown proved to have very little effect on the model’s validity. No study was found to directly compare these results conducted on coniferous forest stands. This shows that there is a further need for studies dealing with a quantitative estimation of the biochemical variables of nature coniferous forests when employing spectral data acquired by the UAV platform at a very high spatial resolution.

The amount and spatial distribution of foliage in a tree canopy have fundamental functions in ecosystems as they affect energy and mass fluxes through photosynthesis and transpiration. They are usually described by the Leaf Area Index (LAI) and the Leaf Area Density (LAD), which can be measured through a variety of methods, including voxel-based methods applied to LiDAR point clouds. A theoretical study recently compared the numerical errors arising from different voxel-based estimation methods for Plant Area Density (PAD) based on Beer’s law-based, contact frequency and Maximum-Likelihood Estimation, showing that the bias-corrected Maximum Likelihood Estimator was theoretically the most efficient. However, this earlier study i) ignored wood volumes; ii) neglected vegetation clumping inside the voxel; iii) ignored instrument characteristics in terms of effective footprint, iv) was limited to a single viewpoint. In practice, retrieving LAD from PAD is not straightforward, vegetation is not randomly distributed in volumes of interest, beams are divergent and forestry plots are usually sampled from more than one viewpoint, to mitigate the effect of occlusion. In the present short communication, we extend the previous efficient formulation to actual field conditions to i) account for the presence of both wood volumes and wood hits, ii) rigorously include correction terms for vegetation and instrument characteristics, iii) integrate multiview data. A numerical comparison with other methods commonly used to combine information from different viewpoints led to error reduction, especially in poorly-explored volumes, which are frequent in actual canopies. Beyond its concision, completeness and efficiency, this new formulation -which can be applied to multiview TLS, but also UAV LiDAR scanning - can help reducing errors in LAD estimation.

Human detection from Unmanned Aerial Vehicles (UAV) is gaining popularity in the field of disaster management, crowd counting, people monitoring. Real time human detection from UAV is a challenging task, because of many constraints involved. This study proposes a system for real time detection of humans on videos captured from UAVs addressing three of these constraints namely, flying height, computation time and scale of viewing. The proposed method integrated an android application with a binary classifier based on Haar-features to automatically detect human / non-human class from UAV images. The video frames were parsed and detected humans from image frames were geo-localized and visualized on Google Earth. The performance was evaluated for geo-localization accuracy, computation time and detection accuracy, considering human coverage – pixel size relationship for various heights and scale factor. Based on flying height - human size relationship and tradeoff between detection accuracy vs computation time, the study came up with optimal parameters for OpenCV’s cv2.cascadeClassifier. detectMultiScale function. This paper establishes a strong ground for further research relating to real time human detection from UAV.

UAV network operation enables gathering and fusion from disparate information sources for flight control in both manned and unmanned platforms. In this investigation, a novel procedure for detecting runways and horizons as well as enhancing surrounding terrain is introduced based on fusion of enhanced vision system (EVS) and synthetic vision system (SVS) images. EVS and SVS image fusion has yet to be implemented real-world situations due to signal misalignment. We address this through a registration step to align the EVS and SVS images. Four fusion rules combining discrete wavelet transform (DWT) sub-bands are formulated, implemented and evaluated. The resulting procedure is tested on real EVS-SVS image pairs and pairs containing simulated turbulence. Evaluations reveal that runways and horizons can be detected accurately even in poor visibility. Furthermore, it is demonstrated that different aspects of the EVS and SVS images can be emphasized by using different DWT fusion rules. The procedure is autonomous throughout landing, irrespective of weather. We believe the fusion architecture developed holds promise for incorporation into head-up displays (HUDs) and UAV remote displays to assist pilots landing aircraft in poor lighting and varying weather. The algorithm also provided a basis rule selection in other signal fusion applications.

In developing nations, such as Ekiti State, Nigeria, the use of remote sensing data, especially satellite and UAV imagery, remains significantly underutilized in land administration. This limits the potential of multi-resolution imagery in land governance and socio-economic development. This study examines factors influencing UAV adoption for land administration in Nigeria, mapping six distinct rural, peri-urban, and urban sites, and creating orthomosaics with resolutions ranging from 2.2cm to 3.39cm. Boundaries were manually delineated from multi-resolution orthomosaics to acquire coordinates, and parcel areas were calculated. Using 0.05m UAV imagery as the reference, the Root Mean Square Error (RMSE) was computed to evaluate 0.1, 0.5, and 1m orthomosaics' accuracy for boundary delineation across the six geographical contexts. The Normalized Parcel Area Error (NPAE) was also calculated to determine how the multi-resolution imageries affected the property areas. Results showed a consistent increase in error with increasing resolution (0.1m to 1m) in formal areas (Igedora, Maryland, Okebola) with physical demarcations, from 0.117m to 1.747m RMSE. In contrast, informal settlements exhibited inconsistent error values, indicating a differing impact of resolution on error between formal and informal areas. The research demonstrates the role of physical demarcations in facilitating cadastral mapping, with formal settlements demonstrating the highest suitability. This study recommends the use of imagery resolution specific to each context, offering guidance for improved land governance. Implications and recommendations include promoting awareness of settlement typologies in aerial imagery use for cadastral mapping, leveraging UAVs for high-resolution aerial imagery, and addressing regulatory challenges to promote UAV adoption. Finally, the RMSE and NPAE values can serve as metrics for assessing different resolution images’ fitness for cadastral mapping.

Drone imagery has the potential to enrich urban planning and preservation, especially where it converges with the growing creation and use of 3D models. The authors have conducted a systematic literature review of articles published between 2002 and 2022, drawing from reputable academic repositories including Science Direct, Web of Science, and China National Knowledge Infrastructure (CNKI), to identify current gaps in existing research in the application of UAVs to the creation of 3D models in urban planning and preservation. Findings indicate five research shortcomings: limited participation of planning experts, research focus imbalance, lack of usage for special scenarios, lack of integration with smart city planning, and limited interdisciplinary collaboration. The study also acknowledges current limitations with UAV applications and discusses possible countermeasures as well as future prospects.

Miscanthus holds a great potential in the frame of the bioeconomy and yield prediction can help improving Miscanthus logistic supply chain. Breeding programs in several countries are attempting to produce high-yielding Miscanthus hybrids better adapted to different climates and end-uses. Multispectral images acquired from unmanned aerial vehicles (UAVs) in Italy and in the UK in 2021 and 2022 were used to investigate the feasibility of high-throughput phenotyping (HTP) of novel Miscanthus hybrids for yield prediction and crop traits estimation. An intercalibration procedure was performed using simulated data from the PROSAIL model to link vegetation indices (VIs) derived from two different multispectral sensors. Random forest algorithm estimated with good accuracy yield traits (light interception, plant height, green leaf biomass and standing biomass) using VIs time series and predicted yield using peak descriptor derived from VIs time series with 2.3 Mg DM ha-1 of RMSE. The study demonstrates the potential of UAVs multispectral in HTP applications and in yield prediction for providing important information needed to increase sustainable biomass production.

The presented study demonstrates the bi-sensor approach suitable for rapid and precise up-to-date mapping of forest canopy gaps for the larger spatial extent. The approach makes use of UAV RGB images on smaller areas for highly precise forest canopy mask creation. Sentinel-2 was used as a scaling platform for transferring information from UAV to a wider spatial extent. The various approaches of the improvement of the predictive performance were examined: (I) the highest R2 of the single satellite index was up to 0.57, (II) the highest R2 using multiple features obtained from the single date, S-2 image was 0.624 and, (III) the highest R2 on the multi-temporal set of S-2 images, was 0.697. Satellite indices such as ARVI, IPVI, NDI45, PSSRa, MCARI, CI, RI, and NDTI were the dominant predictors in most of the ML algorithms. The more complex ML algorithms such as SVM, Random Forest, GBM, XGBoost, and Catboost that provided the best performance on the training set exhibited weaker generalization capabilities. Therefore, a simpler and more robust Elastic Net algorithm was chosen for the final map creation.

Unmanned aerial vehicles (UAVs) represent a new model of social robots for home care of dependent persons. In this regard, this article introduces a study on people’s feeling of safety and comfort while watching the monitoring trajectory of a quadrotor dedicated to determining their condition. Three main parameters are evaluated: the relative monitoring altitude, the monitoring velocity and the shape of the monitoring path around the person (ellipsoidal or circular). For this purpose, a new trajectory generator based on a state machine, which is successfully implemented and simulated in MATLAB/Simulink®, is described. The study is carried out with 37 participants using a virtual reality (VR) platform based on two modules, UAV Simulator and VR Visualiser, both communicating through the MQTT protocol. The participants’ preferences have been a high relative monitoring altitude, a high monitoring velocity and a circular path. These choices are a starting point for the design of trustworthy socially assistive UAVs flying in real homes.

In scenarios such as natural disasters and military strike, it is common for unmanned aerial vehicles (UAVs) to form groups to execute reconnaissance and surveillance. To ensure the effectiveness of UAV communications, repeated resource acquisition issues and transmission mechanism design need to be addressed urgently. In this paper, we build an information interaction scenario in a Flying Ad-hoc network (FANET). The data transmission problem with the goal of throughput maximization is modeled as a coalition game framework. Then, a novel mechanism of coalition selection and data transmission based on group-buying is investigated. Since large-scale UAVs will generate high transmission overhead due to the overlapping resource requirements, we propose a resource allocation optimization method based on distributed data content. Comparing existing works, a data transmission and coalition formation mechanism is designed. Then the system model is classified into graph game and coalition formation game. Through the design of the utility function, we prove that both games have stable solutions. We also prove the convergence of the proposed approach with coalition order and Pareto order. Binary log-linear learning based coalition selection algorithm (BLL-CSA) is proposed to explore the stable coalition partition of system model. Simulation results show that the proposed data transmission and coalition formation mechanism can achieve higher data throughput than the other contrast algorithms.

Geophysical surveys, a conventional means of analyzing the Earth and its environs, have traditionally relied on ground-based methodologies. However, up-to-date approaches encompass remote sensing (RS) techniques, employing both spaceborne and airborne platforms. The emergence of Unmanned Aerial Vehicles (UAVs) has notably catalyzed interest in UAV-borne geophysical RS. This study comprehensively reviews the state-of-the-art UAV-based geophysical methods, encompassing magnetometry, gravimetry, gamma-ray spectrometry/radiometry, electromagnetic (EM) surveys, ground penetrating radar (GPR), traditional UAV RS methods (i.e., photogrammetry and LiDARgrammetry), and integrated approaches. Each method is scrutinized concerning essential aspects such as sensors, platforms, challenges, applications, etc. Drawing upon an extensive review of over 435 scholarly works, our analysis reveals the versatility of these systems, ranging from geophysical development to applications over various geoscientific domains. The reviewed studies unanimously highlight the advantages of UAV RS in geophysical surveys. UAV geophysical RS effectively balances the benefits of ground-based and traditional RS methods regarding cost, resolution, accuracy, and other factors. Integrating multiple sensors on a single platform and fusion of multi-source data enhance efficiency in geoscientific analysis. However, implementing geophysical methods on UAVs poses challenges, prompting ongoing research and development efforts worldwide to find optimal solutions from both hardware and software perspectives.

Wildlife monitoring can be time-consuming and expensive, but the fast-developing technologies of uncrewed aerial vehicles, sensors, and machine learning pave the way for automated monitoring. In this study we trained YOLOv5 neural networks to detect Points of Interest, hare (Lepus europaeus), and roe deer (Capreolus capreolus) in thermal aerial footage and proposed a method to manually assess the parameter mean average precision (mAP), compared to the number of actual false positive and false negative detections in a subsample. This showed that a mAP close to 1 for a trained model does not necessarily mean perfect detection and provided a method to gain insights into the parameters affecting the trained models' precision. Furthermore, we provided a basic, conceptual algorithm for implementing real-time object detection in uncrewed aircraft systems equipped with thermal sensors, with high zoom capabilities, and a laser rangefinder. Real-time object detection is becoming an invaluable complementary tool for the monitoring of cryptic and nocturnal animals with the use of thermal sensors.

The dynamic development of robotics is affecting people's lives. Flying robots replace pilots and crews in performing dangerous tasks. There are various designs of the above-mentioned robots such as multi-rotors, fixed-wing aircraft, helicopters, among which wing-in-ground (WIG) units can also be distinguished. WIG vehicles, which utilize ground effect to enhance efficiency and stability, share similarities with UAVs in their control and aerodynamic challenges. The article presented the results of the autopilot test for the NeoX UAV, which have the potential to be utilized in WIG UAVs. The NeoX was developed at the Air Force Institute of Technology as a reconnaissance flying robot and is a tailless mini UAV. It has a characteristic feature which is the flying wing with a small fuselage. The electric engine with the pusher propeller ensures thrust. The tailless airplane has a greater drag-to-lift ratio than a conventional airplane, but this airplane configuration needs a control system that ensures a stable flight. The structure of auto-pilot for the horizontal flight phase (a cruise phase), the climbing, and the descending phase were presented. The authors concentrated on the longitudinal channel of autopilot and showed the recorded results from the flight tests. The research focused on developing autopilot system that could be adapted for use in WIG craft, which operate with similar aerodynamic principles but require unique control adaptations due to their proximity to the water or ground. The findings from the NeoX UAV tests are instru-mental in enhancing the stability and performance of these specialized crafts, ensuring safer and more efficient operation in their respective environments.

The distribution of tiny sensors over a specific area was first proposed in the late 1990s as a concept known as Smart Dust. Several efforts focused primarily on computing and networking capabilities but quickly ran into problems related to power supply, cost, data transmission, and environmental pollution. To overcome these limitations, we propose using paper-based (confetti-like) chemosensors that exploit the inherent selectivity of chemical reagents, such as colorimetric indicators. In this work, cheap and biodegradable passive sensors made from cellulose could successfully indicate the presence of hazardous chemicals, e.g., strong acids, by a significant color change. A conventional color digital camera attached to a drone could easily detect this from a safe distance. The collected data was processed to define the hazardous area. Our work presents a combination of the smart dust concept, chemosensing, paper-based sensor technology, and low-cost drones for flexible, sensitive, economical, and rapid detection of hazardous chemicals in high-risk scenarios.

We present multi-sensor measurements from satellites, unmanned aerial vehicle, marine radar, thermal profilers and repeated conductivity-temperature-depth casts made in the Kara Gates strait connecting the Barents and the Kara Seas during spring tide in August 2021. Analysis of the field data during an 18-hour period from four stations evidence that a complex sill in the Kara Gates is the site of regular production of intense large-amplitude nonlinear internal waves. Satellite data show a presence of a relatively warm northeastward surface current from the Barents Sea toward the Kara Sea attaining 0.8-0.9 m/s. Triangle-shaped measurements of three thermal profilers revealed pronounced vertical thermocline oscillations up to 40 m associated with propagation of short-period nonlinear internal waves of depression generated by stratified flow passing a system of shallow sills in the strait. The most intense waves were recorded during the ebb tide slackening and reversal when the background flow was predominantly supercritical. Observed internal waves had wavelength of ~100 m and travelled northeastward with phase speeds of 0.8-0.9 m/s. The total internal wave energy per unit crest length for the largest waves was estimated to be equal to 1.0-1.8 MJ/m.

This work is part of an ongoing research project to develop an unmanned flying social robot to monitor dependants at home in order to detect the person’s state and bring the necessary assistance. In this sense, this paper focuses on the description of a virtual reality (VR) simulation platform for the monitoring process of an avatar in a virtual home by a rotatory-wing autonomous unmanned aerial vehicle (UAV). This platform is based on a distributed architecture composed of three modules communicated through the Message Queue Telemetry Transport (MQTT) protocol: the UAV Simulator implemented in MATLAB/Simulink, the VR Visualiser developed in Unity, and the new emotion recognition (ER) System developed in Python. Using a face detection algorithm and a convolutional neural network (CNN), the ER System is able to detect the person’s face in the image captured by the UAV’s on-board camera and classify the emotion among seven possible ones (surprise, fear, happiness, sadness, disgust, anger or neutral expression). The experimental results demonstrate the correct integration of this new computer vision module within the VR platform, as well as the good performance of the designed CNN, with around 85% in the F1-score, a mean of the precision and recall of the model. The developed emotion detection system can be used in the future implementation of the assistance UAV that monitors dependent people in a real environment, since the methodology used is valid for images of real people.

The location and number data of individual fruit trees are critical for planting area investigation, fruit yield prediction, and smart orchard management and planning. These data are conventionally obtained through manual investigation and statistics with time-consuming and laborious effort. Object detection models in deep learning used widely in computer vision could provide an opportunity for accurate detection of individual fruit trees, which is essential for rapidly obtaining the data and reducing human operations errors. This study proposes an approach to detecting individual fruit trees and mapping their spatial distribution by integrating deep learning with unmanned aerial vehicle (UAV) remote sensing. UAV remote sensing collected high-resolution true-color images of fruit trees in the experimental pomelo tree orchards in Meizhou city, South China. An image dataset of deep learning samples of individual pomelo trees (IPTs) was constructed through visual interpretation and field investigation based on the fruit tree images captured by UAV remote sensing. Four different scales of YOLOv5 (YOLOv5s, YOLOv5m, YOLOv5l, and YOLOv5x) for object detection were selected to train, validate, and test on the image dataset of pomelo trees. The results show that the average precision (AP@0.5) of the four YOLOv5 models for validation reach 87.8%, 88.5%, 89.1%, and 90.7%, respectively. The larger the model scale, the higher the average accuracy of the detection result of validation. It suggests that YOLOv5x is a preferred high-accuracy model among the YOLOv5 family and is suitable to realize the detection of IPTs. The number of the IPTs in the study area was counted using YOLOv5x, and their spatial distribution map was made using the non-maximum suppression method and ArcGIS software. This study will provide primary data and technical support for smart orchard management in Meizhou city and other fruit-producing areas.

Drones, as mobile media of the present day, increase the operational and narrative capabilities of television and accelerate the logistics of shooting. Unmanned aerial vehicles with a camera properly steered by a pilot are able, to some extent, to replace a jimmy jib/crane and a dolly; basic technical devices, used in the studios, enabling the creation of narrative systems of pictures in film and television. Television is more and more often using drone footage to report events, broadcast live, as well as create coverage and television documentaries. In many productions the pilot of the drone simultaneously acts as the drone camera operator, which can improve the effectiveness of shooting, but also carries some risk related to flight safety. The article describes and presents in the form of processed footage the real conditional ties of a Visual Line of Sight (VLOS) flight faced by pilots filming with a drone. VLOS is a type of air operation, which requires maintaining eye contact with the drone. In many countries a drone visibility flight is legally sanctioned as VLOS Operation. An experiment was conducted to investigate the interactions between a human and a machine in airspace steered using a controller with a touchscreen. The drone pilot was considered an integral part of the drone’s flight system control Experimental data was collected with the use of a mobile eye-tracker, video cameras, surveys and pilot declarations. During the experiment, eight television drone pilot operators recaptured a model shot under the regime of VLOS flight at low altitude. They all show that both advanced and beginner pilots did not look at the UAV for over half the time of shot execution. The experiment allowed establishing two coefficients related to the effectiveness of a VLOS flight aiming at filming from the drone. The results point to clear differences in screen perception styles used by drone television pilots.. The coefficients were described in the form of mathematical formulas and their limit values were determined. The research also determines the limits of pilots’ perception, within which they are able to film with a drone. The outcomes may help to optimize the process of aerial filming with the use of a drone, carried out for television, film and other media, as well as in a simulation of such a flight for research and training. From the perspective of media science and social communication, the presented study included a technological component that can be accessed through information science, using statistical models and variable distributions. Media scholars can study the impact of the media without having to look into the metaphorical black box. Computer science opens up this possibility.

The rising popularity of UAVs and other autonomous control systems, coupled with real-time operating systems, has increased the complexity of developing systems with the proper robustness, performance, and reactivity. Concurrently, the growing demand for more sophisticated computational tasks, proportionally bigger payloads, battery limitations, and smaller take-off mass necessitates higher energy efficiency for all avionics and mission computers. The purpose of this paper is to develop the technology for experimental studies of indicators of reactivity and energy consumption of the computing platform for unmanned aerial vehicles (UAVs). The paper provides an experimental assessment of the ’Boryviter’ 0.1 computing platform, which is implemented on the ATSAMV71 microprocessor and operates under the open-source FreeRTOS operating system. The results obtained are the basis for developing algorithms and energy-efficient design strategies for the mission computer to solve the optimization problem. The paper provides experimental results of measurements of the energy consumed by the microcontroller and estimates of the reduction in system energy consumption due to additional time costs for suspending and resuming the computer’s operation. The results show that the ’Boryviter’ 0.1 computing platform can be used as a UAV mission computer for typical flight control tasks that require real-time computing under the influence of external factors. As the further work direction, authors plan to carry out the investigation of the proposed energy saving algorithms in scope of the planned NASA’s F’Prime software flight framework. Such an investigation that should be done with the real flight computation load for the mission computer, will help to qualify the obtained energy saving methods and their implementation results.

Incremental control strategies provide undeniable advantages for controlling Uncrewed Aerial Vehicles (UAVs) due to their reduced model dependency and accurate tracking capacities. This is of particular relevance for hybrid UAVs, specially for tail-sitters, which perform complex manoeuvres when transitioning to and from aerodynamic flight. This paper summarizes the research undertaken in the application of the Incremental Nonlinear Dynamics Inversion (INDI) and Incremental Backstepping (IBKS) to a small tail-sitter UAV. After the application of these control strategies in a simulated scenario, the implementation in a Micro-Controller Unit was validated in a Hardware-in-the-Loop scenario. Following such validation, indoor experimental trials were undertaken in order to evaluate the capacity of these controllers to stabilize and control the real aircraft. The stabilization in the flight trials was successfully implemented and allow to conclude that both INDI and IBKS are control strategies suited to control a tail-sitter in vertical flight, providing accurate tracking capabilities under smooth actuation. Furthermore, it was found that the IBKS is significantly more computationally demanding than the INDI, although having a global proof of stability that is of interest in aircraft control.

In recent years, the unmanned aerial vehicle (UAV) synthetic aperture radar (SAR) has become a highly sought-after topic for its wide applications in the field of target recognition, detection, and tracking. However, SAR automatic target recognition (ATR) models based on deep neural networks (DNN) are suffering from adversarial examples. Generally, non-cooperators rarely disclose any information about SAR-ATR models, making adversarial attacks challenging. In this situation, we propose Transferable Adversarial Network (TAN) to attack these models with highly transferable adversarial examples. The proposed method improves the transferability via a two-player game, in which we simultaneously train two encoder-decoder models: a generator that crafts malicious samples through a one-step forward mapping from original data, and an attenuator that weakens the effectiveness of malicious samples by capturing the most harmful deformations. In particular, compared to traditional iterative methods, our approach is able to one-step map original samples to adversarial examples, thus enabling real-time attacks. Experimental results indicate that the proposed approach achieves state-of-the-art transferability with acceptable adversarial perturbations and minimum time costs compared to existing attack methods, i.e., it excellently realizes real-time transferable adversarial attacks.

The demands for high power and low emissions put focus on energy efficiency when developing new engines. An important part is the UAV engine cooling system, which cools the engine structure below damaging temperatures. For high temperatures in the cooling system there is a risk that boiling occurs and while the initial nucleate boiling enhances the cooling effect, the subsequent Film boiling decreases the heat transfer drastically. It is important to understand the benefits and limitations of various fluids when designing a two-phase cooling system. This paper proposes an alternative organic coolant. Its normal application range is 15°C to 400°C, and its pressure range is from atmospheric to 10.6 bar. DOWTHERM A fluid possesses unsurpassed thermal stability at temperatures of 400°C. This fluid, in both the liquid and vapor form, is noncorrosive toward common metals and alloys. Even at the high temperatures involved, the equipment usually exhibits excellent service life. Original equipment in many systems is still being used after 30 years of continuous service. The numerical results, described in this paper, show the potential of DOWTHERM A as a good alternative for cooling a UAV engine. It will extend the working temperature range of the Diesel engine and will maintain the structural integrity of the piston, cylinder and the piston rings.

As UAVs are increasingly employed across various industries, the demand for robust and accurate detection has become crucial. LiDAR has developed as a vital sensor technology because to its ability to offer rich 3D spatial information, particularly in applications such as security and airspace monitoring. This review systematically explores recent innovations in LiDAR-based drone detection, deeply focusing on the principle and components of LiDAR sensor, its classifications based on different parameters and scanning mechanisms, as well as the approaches for processing LiDAR data. The review briefly compares several deep learning approaches, including point-based, voxel-based, and hybrid models, that have improved drone detection, tracking, and classification. We also explore the integration of multi-modal sensor fusion, which combines LiDAR data with other complimentary modalities to improve UAV detection and tracking in complex environments such as GNSS-denied zones.

Remotely Piloted Aircraft Systems (RPAS) are increasingly becoming relevant actors flying through the airspace and will assume much more importance in the future perspective. In order to allow their safe integration with manned conventional traffic in non-segregated airspaces, in accordance with the overall Air Traffic Management (ATM) paradigm, specific enabling technologies are needed. As well known, among the enabling technologies identified as crucial for RPAS integration into the overall ATM system, the Detect and Avoid (DAA) technology is fundamental. In the meantime, to support extended surveillance, the universal introduction on-board of aircraft of cooperative Automatic Dependent Surveillance – Broadcast (ADS-B) is increasingly implemented, having the potential to allow coverage of the whole airspace also in remote areas not usually covered by conventional radar surveillance. In this paper, the experimental results are presented and discussed that have been obtained through the real-time validation, with hardware and human in the loop (RTS-HIL) simulations, of an automatic ADS-B based Separation Assurance and Collision Avoidance System aimed to support RPAS automatic operations as well as remote pilot decision making. In the paper, after an introductory outline of the Concept of Operations (ConOps) of the system and of its architectural organization, while also providing basic information about the main system functionalities, the description is reported of the tests that have been carried out and the obtained results are described and discussed, in order to emphasize the performances and limitations of the proposed system. In particular, not only the quantitative performances obtained are reported and commented but also the feedbacks received by the pilots in order to improve the system are described, for instance in terms of preferred typology of conflict resolution manoeuver elaborated by the system.