This research seeks to solve the multi-faceted problem of waste disposal by analyzing the application of waste plastic and tyre material within non-structural concrete to ensure more sustainability and less environmental degradation. Study focusses on material properties including specific gravity, water absorption and bulk density and characteristics of the concrete that is produced by the utilization of the above waste aggregates including workability, compressive strength, flexural strength and tensile strength. This paper employs secondary data collection and MATLAB in the analysis of the findings pointing to the fact that the mechanical properties reduce with the level of waste content yet emphasizing the green aspect of such materials. Thus, a complex and diverse effect is demonstrated by the life cycle assessments (LCA) for global warming, ozone depletion, terrestrial ecotoxicity, and acidification. Furthermore, the utilization of waste materials decreases the compressive, flexural, and tensile strength, but it provides distinct ecological benefits which prove the importance of proper mix proportions for concrete performance. The outcomes of this research will be useful for further investigation in the application of the concept as well as to call for the development of new ideas for the improvement of bonding of wastes to aggregates in concrete.

Excessive activation of frog eggs, so called overactivation, can be initiated by strong oxidative stress, leading to expedited calcium-dependent non-apoptotic cell death. Overactivation also occurs spontaneously, albeit with a low frequency, in natural populations of spawned frog eggs. Currently, cytological and biochemical events of the spontaneous process are not characterized. In the present study, we demonstrate that spontaneous overactivation of Xenopus frog eggs, similarly to oxidative stress- and mechanical stress-induced overactivation, is characterized by the fast and irreversible contraction of the egg’s cortical layer, increase in the egg size, depletion of intracellular ATP, drastic increase in the intracellular ADP/ATP ratio, and degradation of M phase-specific cyclin B2. These events manifest in eggs in the absence of caspase activation within just one hour of triggering overactivation. Importantly, large amounts of ATP and ADP leak from the overactivated eggs, indicating that plasma membrane integrity is compromised in these cells. The rapture of the plasma membrane and acute depletion of intracellular ATP define explicitly necrotic cell death. Finally, we report that egg overactivation can occur in the frog’s genital tract. Our data argue that mechanical stress may be a key factor promoting egg overactivation during natural spawning in frogs.

PURPOSE: The aim of this study was to identify the incidence of early mechanical failure in the first post-surgical year in patients who had undergone spinal surgery, and to assess the related risk factors. METHODS: Retrospective observational study of a prognostic cohort was conducted at an orthopaedic hospital, examining all patients with spine degenerative disease who consecutively underwent arthrodesis surgery between March 2018 and March 2019. The incidence of postoperative mechanical failure during the first year was calculated as primary outcome; the time between the date of the implant surgery and diagnosis of the mechanical failure was calculated as secondary outcome. RESULTS: A total of 237 patients were identified for statistical analysis. The median age of the group of patients was 47 years (IQR of 44), and 66.6% were female. The incidence of mechanical failure in the first postoperative year was 5.1% overall with 12 events and the median time between surgery and the need for revision surgery was 5 months (IQR=7.75). ASA score (OR= 2,39; p=0.134), duration of the surgical procedure (OR=1,27; p=0,006) and inability to walk at discharge (OR=7,86; p=0,072) were independent risk of factor associated with the mechanical failure. CONCLUSION: Higher ASA score and longer duration of surgery are risk factors for mechanical failure in the first year in patients who had undergone spinal surgery and must be carefully considered when planning spinal surgery. During hospitalization, recovery of ambulation must be encouraged to prevent mechanical failure. All these factors are useful in identifying patients with a closer follow-up is needed.

The evolution of transportation has been inextricably tied to the progress of civilization. Through innovation, the automobile business has been working to improve safety, quality, and compliance with environmental regulations. Electric vehicles have made significant strides in this area, but optimizing their efficiency requires a special focus because they expend energy that can be recovered in a variety of ways. Energy harvesting, a cutting-edge technology that captures wasted energy from vehicles, has recently received a lot of attention as it constitutes a means to improve the efficiency of electric vehicles. Dissipated energy can be converted into electricity using regenerative energy recovery systems and put to various uses. This study tenders a thorough examination into energy recovery technologies which could be applied to the various types of energy dissipated in electric vehicles. Firstly, the paper investigates the possible sources of energy recoverable from an electric vehicle, as well as the various types of energy dissipated. Secondly, the article examines the energy recovery technologies most frequently used in vehicles, categorizing them according to the type of energy and application. Finally, it determines that with further research and development, energy harvesting holds considerable potential for improving the energy efficiency of electric vehicles. New and innovative methods for capturing and utilizing wasted energy in electric vehicles can be established. The potential benefits of applying energy recovery systems in electric vehicles is a vital issue for the automobile industry to focus on due to the potential benefits involved. The ongoing progress currently being made in this field is expected to play a significant role in shaping the future of transportation.

Bobbin Tool Friction Stir Welding (BTFSW) is a variant of FSW process using the special two shoulder tool that forms the top and bottom weld surface. As such, a significant simplification of welding setup is achieved. One of the dominant parameters of BTFSW process is the interference between tool shoulder pinch gap and weld metal thickness. In this research, the influence of interference of the square pin tool with convex shoulders on process temperature, microstructure, tensile, impact and bend performance were studied, and appropriate correlations were devised. The base metal was aluminum-magnesium alloy, with the interference varied in the range of 0.1 to 0.5 mm. The worm defects and irregularities were found in all specimens except in specimen welded with 0.4 mm interference. Optimal interference of 0.4 mm resulted in the highest mechanical properties, which, in terms of tensile strength and reduction of area were similar to the base metal. Furthermore, impact strength was significantly higher, which was attributed to grain refinement effect in the nugget zone.

Fe rich soft magnetic alloys are candidates for applications as magnetic sensors and actuators. These alloys can also be added to hard magnetic compounds to obtain spring magnets. In this work we produce two nanocrystalline Fe-Zr-B-Cu alloys by the powder metallurgy powder technology of mechanical alloying. The increase of the boron content favors the reduction of the crystalline size. Thermal analysis (by differential scanning calorimetry) shows at temperatures between 450 and 650 K wide exothermic processes, associated with the relaxation of tensions of the alloys produced by milling. At high temperatures, a main crystallization peak is found. The apparent activation of this process was determined by Kissinger and isoconversional methods. The values are compared with those found in the scientific literature. Likewise, adapted thermogravimetry permits to determine the Curie temperature. The functional response has been analyzed by hysteresis loop cycles. According to the composition, the decrease of the Fe/B ratio diminishes the magnetic soft behavior.

Objective: This study aims to identify the impact of nutritional factors on mechanical ventilation duration for critical patients. Patients and Methods: The current study was a single-center, prospective observational design which enrolled one-hundred critically ill patients who were admitted to an intensive care unit (ICU). It demonstrates purposive sampling and also performs the descriptive nutritional factors influencing the mechanical ventilation duration. Daily calories target requirement scale (DCRS), subjective global assessment form (SGA), dyspnea assessment form, and APACHE II have been used as methods in the study along with time to initial enteral nutrition (EN) after 24-hour admission and daily calories target requirement over 7 days to assess patients. Data is analyzed using the multiple regressions. Results: As a result, nutritional status monitoring, time to initial EN, calories and target requirements are statistically positive significance associated with the mechanical ventilation duration respectively (R = 0.54, R = 0.30, R= 0.40, p < 0.05). However, age, illness severity, and dyspnea scales are not associated with the mechanical ventilation duration (p> 0.05). Therefore, the nutritional status, malnutrition scores and calorie target requirements can be used to significantly predict the mechanical ventilation duration. The predictive power is 58 and 28.0% of variance. The most proper influencer to predict the mechanical ventilation duration is nutritional status or malnutrition scores. Conclusion: The research findings show that the nutritional status, time to initial EN, and calorie target requirement within 7 days of admission are associated with the mechanical ventilation duration in the critical patients. Therefore, it can be used to develop guidelines reducing the mechanical ventilation duration and to promote the ventilator halting for critical patients.

The distributed long-range sensing system using the standard telecommunication single-mode optical fiber in a function of a distributed sensor for sensing of mechanical vibrations is described. Various events generating vibrations such as walking or running person, moving cars, trains and others can be detected, localized and classified. The sensor and related sensing system components were designed and constructed and the system was tested both in the laboratory and in the real situation with 88 km telecom optical link, and the results are presented.

With the emergence of COVID-19 we are confronted with a new clinical picture of acute respiratory distress syndrome in the intensive care unit. In the majority of patients, the respiratory mechanics are very different from the “normal” ARDS patient. We measured transpulmonary pressure and dead space ventilation to assess the effects of high and low PEEP levels on lung compliance and ventilation-perfusion mismatching. Advanced respiratory mechanics were assessed in 14 patients. Compared to ARDS patients, lung compliance was relatively high (61 ± 5 mL/cmH₂O). COVID-19 patients had high dead space ventilation and gas exchange impairment (Bohr 52 ± 3%; Enghoff modification 67 ± 2%; ventilatory ratio 2.24 ± 0.23). we show that higher PEEP levels decrease lung compliance and in most cases increase dead space ventilation, indicating that high PEEP levels probably cause hyperinflation in patients with COVID-19. We suggest using prone position for an extended period of time, and apply lower PEEP levels as much as possible.

Cu₆Sn₅ whiskers precipitated in Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer were found and investigated after reflow soldering and during aging. Ag₃Sn fibers can be observed around Cu₆Sn₅ whiskers in the matrix microstructure, which can play an active effect on the reliability of interconnection. Different morphologies of Cu₆Sn₅ whiskers can be observed, and hexagonal rod structure is the main morphology of Cu₆Sn₅ whiskers. A hollow structure can be observed in hexagonal Cu₆Sn₅ whiskers, and a screw dislocation mechanism was used to represent the Cu₆Sn₅ growth. Based on mechanical property testing and finite element simulation, Cu₆Sn₅ whiskers were regarded as having a negative effect on the durability of Sn3.0Ag0.5Cu/Cu interconnection in concentrator silicon solar cells solder layer.

The dynamic landscape of 3D printing has experienced a notable surge in the development of diverse filaments tailored for a wide range of applications in medicine. This experimental study thoroughly examines the mechanical properties of nine popular 3D printer filaments, namely PLA, ABS, HIPS, PETG, PA, Carbon Fiber, Ceramic, PMMA, and Metal composite. Focusing on key aspects such as tensile strength and compressive tests, the study delves into the intricate mechanical characteristics of these 3D printer filaments. In addition to the mechanical properties, the study provides a comprehensive exploration of essential filament attributes, including melting point, bed temperature requirements, and density of nine different filament properties. Furthermore, the study addresses crucial considerations in material selection for different applications. Through insightful comparisons, the article illuminates the advantages and limitations of various available filaments within the realm of applications. This study serves as a valuable resource, offering nuanced insights for researchers, engineers, and medical professionals seeking a deeper understanding of the mechanical characteristics of 3D printer filaments and their potential applications.

Abstract: Comorbidities of patients may be related to the duration of mechanical ventilation, survival, and Candida isolation during intensive care unit (ICU) stay. To examine the frequency of Candida isolation and significant comorbidities in the surgical intensive care unit (ICU) in Osijek University Hospital, Croatia, the data from the electronic database from May 2016 to June 30, 2023, were analyzed. In a cross-sectional study examining 15,790 microbiological samples, different strains of Candida were observed in 581 samples from 236 patients. The control group was 160 consecutive patients from March-May 2019, and 161 in the same months of 2020 (pre- and post-COVID-19). Comorbidities, duration of mechanical ventilation and survival were compared. Patients with isolated Candida were more often non-elective, had significantly more heart, kidney, liver diseases and sepsis (P<0.001). The duration of mechanical ventilation was 9.2 [2.2-9.24], 96 [24-146], 160 [19.5-343] and 224 [73.5-510] hours in controls, and patients with Candida albicans, non-albicans, and in patients with ³2 Candidas isolated. The mortality was significantly higher and reached 42% in patients with Candida isolated, while in the control group, it was 19% (P<0.001). In a multivariate analysis adjusted for patient’s age, SAPS II score, days of ICU, and type of admission, only sepsis was independent predictor of mortality (OR = 2.27).

UEDVT still remains an underdiagnosed entity due to a significant percentage of patients who remain asymptomatic. The etiology of UEDVT is overwhelmingly attributed to secondary causes including but not limited to central venous access devices and malignancy. Treatment modalities include anticoagulation, catheter directed thrombolysis, percutaneous mechanical thrombectomy or a multimodality approach along with the management of underlying etiology. We describe a case of a female with breast cancer, who came with left UEDVT and CVC malfunction and was successfully treated using the ClotTriever system to maintain continuous intravenous access.

Conventional heat treatment is not capable of converting a sufficient amount of retained austenite into martensite in high-carbon or high-carbon and high-alloyed iron alloys. Cryogenic treatment induces the following alterations in the microstructures: (i) a considerable reduction in the retained austenite amount, (ii) formation of refined martensite coupled with an increased number of lattice defects, such as dislocations and twins, (iii) changes in the precipitation kinetics of nano-sized transient carbides during tempering, and (iv) an increase in the number of small globular carbides. These microstructural alterations are reflected in mechanical property improvements and better dimensional stability. A common consequence of cryogenic treatment is a significant increase in the wear resistance of steels. The current review deals with all the mentioned microstructural changes as well as the variations in strength, toughness, wear performance, and corrosion resistance for a variety of iron alloys, such as carburising steels, hot work tool steels, bearing and eutectoid steels, and high-carbon and high alloyed ledeburitic cold work tool steels.

Materials characterised by magnetorheological properties are non-classic engineering materials. A significant increase in the interest of scientific community in materials from this group can be observed over the recent several years. The results of research presented in this article are oriented on the examination of said materials’ mechanical properties. In order to do so, stress relaxation tests were conducted on cylindrical samples of magnetorheological elastomers loaded with compressive stress for various values of magnetic induction (B1 = 0 mT, B2 = 32 mT, B3 = 48 mT, and B4 = 64 mT) and temperature (T1 = 25° C, T2 = 30° C, and T3 = 40° C). The results of these tests indicate that the stiffness of examined samples increases along with the increase of magnetic field induction and decreases along with the increase of temperature. On this basis, it has been determined that: the biggest stress amplitude change caused by the influence of magnetic field was σ0ΔB = 12.7% and the biggest stress amplitude change caused by the influence of temperature was σ0ΔT = 11.3%. As a result of applying a mathematical model, it has been indicated that the stress relaxation in the examined magnetorheological elastomer for the adopted time range (t = 3600 s) has a hyperbolic decline nature. The collected test results point to examined materials being characterised by extensive rheological properties, which leads to a conclusion that it is necessary to conduct further tests in this scope.

In this paper, an adaptive technology and the interconnection and damping assignment passivity-based control method are combined to solve the stabilization problem for underactuated mechanical systems with uncertainties (including matched and unmatched). Uncertainties include unknown friction coefficients and unknown terms in kinetic energy and potential energy. A novel adaptive interconnection and damping assignment passivity-based control scheme is proposed and an adaptive stabilization controller is designed to make the closed-loop system locally stable. Verification is conducted on the ball and beam system, taking into account uncertainties of friction coefficients, kinetic energy, and potential energy. The locally asymptotic stability is demonstrated using the LaSalle’s invariance principle and approximate linearization. The effectiveness of the proposed control law is verified through numerical simulations.

Space vehicles may be propelled by solar sails exploiting the radiation pressure coming from the sun and applied on their surfaces. This work deals with the adoption of Shape-Memory Alloy (SMA) elements in the sail deployment mechanism activated by the Joule Effect, i.e. using the same SMA elements as a resistance within suitable designed electrical circuits. Mathematical models were analyzed for the thermal analysis by implementing algorithms for the evaluation of the temperature trend depending on the design parameters. Several solar sail prototypes were built up and tested with different number, size and arrangement of the SMA elements, as well as the type of the selected electrical circuit. The main parameters have been discussed in the tested configurations and advantages discussed as well.

The decreasing width, increasing aspect ratio RDL presents significant challenges to design for reliability (DFR) of advanced package. Therefore, this paper proposes a ML based RDL modeling and simulation method. In the method, RDL is divided into blocks and subdivided into pixels of metal percentage, and the RDL is digitalized as tensors. Then, an ANN-based surrogate model is built and trained by a subset of tensors to predict the equivalent material properties of each block. Lastly, all blocks are transformed into elements for simulations. For validation, line bending simulations were conducted on an RDL, with the reaction force as accuracy indicator. The results show that neglecting layout impact causes critical errors as substrate thins. By the method, the reaction force error is 2.81% and the layout impact can accurately be considered with 200×200 elements. For application, the TCT maximum temperature state simulation was conducted on a CPU chip. The simulation indicates that for advanced package the maximum stress more likely occurs in RDL rather than bumps, both RDL and bumps are critical impacted by layouts, and RDL stress is also impacted by vias/bumps. The proposed method precisely concerns layout impacts with little resources, presents an opportunity of efficiency improvement.

Abstract. This article proposes new fuzzy controller to regulation the voltage, damp the oscillations and limit the overshoot behavior in single-machine infinite-bus power system. Two different independent MISO fuzzy controllers are designed. First controller, is voltage stabilizer and it composes of two adaptive fuzzy modules and proportional gain AVR. The voltage stabilizer is designed to regulate the terminal voltage, damp the voltage oscillation and limit the voltage overshoot to the industrial maximum allowable limit. The input signals of this stabilizer is are taken from the terminal voltage and the imposed voltage disturbance that can be read from any smart relay. The fuzzy output is used as feedback signal to control the AVR in order to achieve stabilized voltage equal to the reference voltage. The second fuzzy controller is designed with two input signals; “mechanical angle” and its derivative, and one output which is used as feedback signal to adapt the damping torque in order to damp the mechanical oscillation fast and with maximum overshoot not exceeding 10%, and hence damp the power angle oscillation that is important in the PSS improvement. MATLAB-SIMULINK was used for modelling and the test cases simulation. The results show very good performance for the proposed fuzzy controllers.

Mechanical ventilation is a life-saving treatment for critically ill patients who are struggling to breathe independently due to injury or disease. Globally, large numbers of Individuals have always required mechanical ventilation per year. The Covid-19 pandemic elevated the significance of the mechanical ventilation which have played a significant role in sustaining Covid 19 infected critically ill patients who could not breathe on their own. The pandemic drew the attention of the world to the shortage of ventilators globally.This research work presents the formulation of a detailed Port Hamiltonian model of a mechanical ventilator integrated to the human respiratory system. The interconnection and coupling conditions for the various subsystem within the mechanical ventilator and the coupling between the mechanical ventilator and the human respiratory system is also presented.A structure preservation discretization is provided along side numerical simulations and results. The obtained results are found to be comparable to results presented in literature.The future work will include the design of suitable controllers for system.

The mechanical pre-treatment constitutes an unavoidable pre-step prior to biofuels conversion. As the cost of this step is often underestimated, recently researchers have striven to identify and characterize the mechanical pre-treatment effects in terms of post-treatment physical characterization, derived improvement of enzymatic digestibility, and output yields. The status of existing mechanical pre-treatment techniques is reviewed by substrate’s typology for lignocellulose biomass, focusing on comminution techniques. Emphasis has been dedicated to the particle size achieved after treatment, crystallinity breakage and eventual inhibitory phenomena deriving from the application of particle size reduction, which are analysed and discussed.

Lightweight component design is effectively achievable through the sandwich structures, many past research studies in the aerospace and racing sectors (since 1920s) has proven it. To extend their application into automotive and other transport industries, the manufacturing cycle times must be reduced. This can be achieved by thermoplastic sandwich materials of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widespread the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). For an increase in reproducibility of the sandwich component production and a decrease in manufacturing defects, numerical modelling methods and experimental validation are needed. The finite element (FE) modelling of this thermoforming process is a thermo-mechanical assignment with all three: material, geometry, and boundary non-linearities. In the scope of this work, the material behavior of different sandwich components (cover layers, honeycomb core, interface) under thermo-mechanical loads is characterized in detail, and a complex numerical model is developed to describe the thermoforming process of thermoplastic-based sandwich laminate. The critical forming condition like wrinkling that occurs due to friction in a sandwich or poor intra-ply shear in cross-ply studied, validated, and optimized. A thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used for this study, and numerical modelling was executed in LS-DYNA software.

In order to address the issues of weight, cost and sustainability issues associated with the application of glass fibre in structural composites, plant fibres are proposed as an alternative to reduce and replace the usage of glass fibres. Despite this, there is still a gap in comprehensive research on plant fibre composites, especially with regard to their durability in real structural applications. This research investigates the fatigue and impact properties of pultruded hybrid polyester composites reinforced with glass fibre and kenaf, tailored for structural applications. Utilising kenaf fibres in mat form, unidirectional glass fibre direct roving yarns and unsaturated polyester resin as key components, pultruded kenaf/glass hybrid profiles were meticulously fabricated. Comparative cost and weight analyses were conducted between pultruded hybrid and non-hybrid profiles. The study showed that the pultruded kenaf/glass alternative laminates exhibit commendable fatigue and impact resistance, making them suitable for use in moderately loaded structural applications. Moreover, the use of kenaf as a hybrid alternative shows significant cost and weight reductions. This research provides a basis for the development of sustainable and efficient structural materials and highlights the significant role of material design in shaping the future of engineering applications.

It is generally accepted that the human abdominal wall is comprised of skin, subcutaneous tissues, muscles and their aponeuroses, and the parietal peritoneum. Understanding these layers and their mechanical properties provides valuable information to those designing procedural skills trainers, supporting surgical procedures (hernia repair), and engineering-based work (in silico simulation). However, there is little literature available on the mechanical properties of the abdominal wall in layers or as a composite. This work characterizes the tensile properties of the human abdominal wall by layer and as a partial composite. Tissues were collected from fresh-never-frozen and fresh-frozen cadavers and tested in uniaxial tension at a rate of 5 mm/min until failure. Stress-strain curves were created for each sample, and the values for elastic moduli, ultimate tensile strength, and strain at failure were obtained. The experimental outcomes from this study demonstrated variation of tensile properties within and between tissues. The data also suggest that the tensile properties of composite abdominal walls are not additive. Ultimately, this body of work contributes to a deeper comprehension of these mechanical properties and will serve to enhance patient care, refine surgical interventions, and assist with more sophisticated engineering solutions.

The impact induced by cavitation bubble collapse can be utilized for mechanical surface treatment to improve fatigue properties of metals including additive manufactured metallic materials. A peening method using cavitation impact induced by a pulsed laser is called “laser cavitation peening (LCP)”. Normally, a Q-switched Nd:YAG laser, whose pulse width is a few nanoseconds, is used for LCP, which improves the fatigue strength. The problem with LCP is that the processing time is too slow. If a laser pulse whose pulse width is a few hundred microseconds can be utilized for LCP, the repetition frequency can be increased drastically using other types of laser systems such as a fiber laser. In the present paper, in order to reveal the possibility of LCP using a pulsed laser width of a few hundred microseconds, the use of LCP with a normal-oscillation Nd:YAG laser (pulse width ≈ 200 us) was investigated. It is demonstrated that LCP with the normal-oscillation Nd:YAG laser produced curvature in an aluminum alloy plate.

Advanced coatings are essential to modern technologies, as they optimise surface characteristics for different application scenarios. Transparent and self-cleaning coatings are increasingly used as protective coatings for various applications, such as foldable touchscreens, windows, and solar panels. Moreover, incorporating other functionalities such as high hardness, wear resistance, and flexibility into transparent and self-cleaning coatings is important for broadening the use cases. Although many kinds of multifunctional coatings have been developed, it is still difficult to embody several properties in one coating adequately, as some properties, such as hardness and flexibility, are inherently contrastive. This review first describes basic principles, including wetting ability, photocatalytic reactions, photo-induced hydrophilic phenomena, and the implication of self-cleaning. The desired properties of multifunctional coatings are then listed, and methods for evaluating different properties are used. Recent progress in various preparation methods for multifunctional coatings, including the sol-gel, dip/spin, and chemical vapour deposition (CVD) methods, are also presented. Magnetron sputtering (MS) technology is widely used in coating preparation. Compared with chemosynthesis and CVD, MS is time-saving, suitable for industrial production, and environmentally friendly. Coatings prepared by MS usually possess excellent mechanical properties. Thus, we highlight the current research status of MS technology in multifunctional coating preparation. Moreover, according to the multilayer design structure of coatings, their optical and mechanical properties and self-cleaning ability can be controlled by combining the characteristics of different materials. Finally, combining photocatalytic materials such as TiO2 with other materials through a multilayer structure to obtain a multifunctional coating with excellent overall properties is discussed.

In order to produce nanostructured Ti0.9Cr0.1C powders, an elemental powder mixture of titanium, chromium, and graphite is milled in this work using a high-energy ball mill for various milling times. Microstructural characteristics such as crystallite size, microstrain, lattice parameter, and dislocation density are determined using X-ray diffraction (XRD). Mechanical alloying successfully produced nanocrystalline (Ti,Cr)C with an average crystallite size of 11 nm. This size of the crystallites is also directly verified using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to investigate the morphology of the samples. The novelty of this work is advancing the scientific understanding of the effect of milling time on the particle size distribution and crystalline structure, and also understanding the effect of the spark plasma sintering on the different properties of the bulks. Densified cermet samples were produced from the nanocrystalline powders, milled for 5, 10 and 20 hours by SPS process at 1800 degrees for 5 min under a pressure of 80 MPa. Phase changes of the produced cermets were examined according to XRD, SEM/EDX analyses. Significant amounts of Cr and Fe elements were detected, especially in the 20 h milled cermet. The bulk forms of the milled powders for 5 and 20 h had a relative density of 98.43 and 98.51 %, respectively. However, 5 h milled cermet had 93.3 HRA because of the more homogeneous distribution of the (Ti,Cr)C phase, the low iron content and high relative density. According to the 0.0011 mm/year corrosion rate, and 371.68 kΩ*cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h cermet was the specimen with the highest corrosion resistance.

Time and cost-efficient techniques are essential to avoid extra conventional experimental studies with large date-set to characterize the mechanical properties of composite materials. Correlation between the structural performance and mechanical properties could be captured through the efficient predictive models. Several ensembled Machine Learning (ML) methods were implemented in this study, to materially characterize carbon nanotube (CNT)-reinforced cement-based composites. Proposed models were compared with each other to represent the accuracy of each method. The Flexural and Compressive Strength (target values) of CNT reinforced composites were predicted based on the data-rich framework provided in previous experimental investigations. These data were utilized for training of the proposed models by employing SciKit-Learn library in Python, followed by hyper-parameter tuning and k-fold cross-validation method for obtaining an efficient model to predict the target values. Random Forest (RF) and Gradient Boosting Machine (GBM) were developed for this purpose. The findings of this study would be useful for prospective composite designers in case of sufficient experimental data availability for ML model training.

The paper contains the results of the 100-hour test campaign of the Additive Manufactured (AM) spare part (retainer – slipper) dedicated for an exact axial piston pump. The material of the retainer-slipper has been identified by using energy dispersive spectroscopy and replaced by other – with similar material properties as the original one. The obtained spare part had been subjected to only one postprocessing type (sandblasting) to analyze the influence of the rough part after the AM process. The whole test campaign has been divided into stages, where after each stage microscopic measurements have been made. During microscopical investigation roughness and geometrical measurements were conducted. The results revealed that it is possible to replace parts in hydraulic pumps with the use of AM. 100-hour test campaign caused about 500% increase in the surface roughness of the pump’s original part which was cooperated with the AM spare retainer-slipper, without any damages to the test system.

Closed timelike curves (CTCs), non-intuitive theoretical solutions of general relativity field equations can be modelled in quantum mechanics in a way, known as Deutsch-CTCs, to circumvent one of their most paradoxical implications, namely, the so-called grandfather paradox. An outstanding theoretical result of this model is the demonstration that in the presence of a Deutsch-CTC a classical computer would be computationally equivalent to a quantum computer. In the present study, the possible implications of such a striking result for the foundations of quantum mechanics and the connections between classicality and quantumness are explored. To this purpose, a model for fundamental particles that interact in physical space exchanging carriers of momentum and energy is considered. Every particle is then supplemented with an information space in which a probabilistic classical Turing machine is stored. It is analysed whether, through the action of Darwinian evolution, both a classical algorithm coding the rules of quantum mechanics and an anticipation module might plausibly be developed on the information space from initial random behaviour. The simulation of a CTC on the information space of the particle by means of the anticipation module would imply that fundamental particles, which do not possess direct intrinsic quantum features from first principles in this information-theoretic Darwinian approach, could however generate quantum emergent behaviour in real time as a consequence of Darwinian evolution acting on information-theoretic physical systems.

A better understanding of diseases progress in tissues vest on the accurate understanding of tissues under mechanical loading. Also, development of therapies for injuries may depend on the available mechanical data for soft tissues. In this study, the raw data of biaxial tensile testing of sclera soft tissue is presented in this paper. Biaxial mechanical testing of soft tissues presents details understanding of how soft tissues behave when compared to uniaxial testing. Biomechanical properties of soft tissues are vital in the development of accurate computational models. Reliable computational models of studying mechanisms of diseases depends mainly on the accurate and more details mechanical behavior of soft tissues. These accurate and detailed computational models may be utilized to further develop the understanding and therapies of various diseases. The mechanical tensile testing was conducted on the passive sheep sclera. Engineering stress vs strain of several samples of the sheep sclera are further presented determined from force and displacement experimental data. The goal of this paper is to make available biaxial data of sheep sclera soft tissue that can be further utilized.

Shape-memory hydrogels (SMH) are as multifunctional, actively-moving polymers of interest in biomedicine. In loosely crosslinked polymer networks gelatin chains may form triple helices, which can act as temporary netpoints in SMH, depending on the presence of salts. Here, we show programming and initiation of the shape-memory effect of such networks based on a thermomechanical process compatible with the physiological environment. The SMH were synthesized by reaction of glycidylmethacrylated gelatin with OEG α,ω-dithiols of varying crosslinker length and amount. Triple helicalization of gelatin chains is shown directly by wide-angle X-ray scattering and indirectly via the mechanical behavior at different temperatures. The ability to form triple helices increased with the molar mass of the crosslinker. Hydrogels had storage moduli of 0.27-23 kPa and Young’s moduli of 215-360 kPa at 4 °C. The hydrogels were hydrolytically degradable, with full degradation to water soluble products within one week at 37 °C and pH = 7.4. A thermally-induced shape-memory effect is demonstrated in bending as well as in compression tests, in which shape recovery with excellent shape recovery rates Rr close to 100% were observed. In the future, the material presented here could be applied e.g. as self-anchoring devices mechanically resembling the extracellular matrix.

Fired bricks have shown tremendous potential as a construction material due to their properties. However, their use required some specifications in terms of quality, resistance, and durability. In developing countries, the lack of tools to make test specimens leads to many defects in these brick specimens responsible for low durability and weak precision during mechanical tests and shrinkage. In this study, a simple and traditional method of making test bricks is presented. This simple method allows the production of bricks with the required properties. This method is especially efficient for a firm or semi-soft pastes consistency. The handmade pastes do not stick into the walls of the mold like the case of steel molds and it gives specimens with standard shape, smooth surface, and sharp edges. The resulting fired bricks exhibit high mechanical strength comparable and even better than those of conventional methods.

We demonstrate high quality (intrinsic Q factor ~2.8×106) racetrack microresonators fabricated on lithium niobate (LN) thin film with a free spectral range (FSR) of ~86.38 pm. By integrating microelectrodes alongside the two straight arms of the racetrack resonator, the resonance wavelength around the 1550 nm can be red shifted by 92 pm when the electric voltage is raised from -100 V to 100 V. The microresonators of the tuning range spanning over a full FSR is fabricated using photolithography assisted chemo-mechanical etching (photolithography assisted chemo-mechanical etching, PLACE).

Background: The main factors to influence on the stroking performance of club head are alloy and spring-like effect. Design the structure of new club face to create the fairway wood which can show best stroking feeling and let driving distance become longer. Purpose: The club face of fairway wood is processed through the iron alloy heating procedure and CNC to innovate the club head with high spring-like effect (characteristic time). Method: (1) Use 455 stainless steel processed by heating and aging treatment, to do the analysis on microstructure and mechanical properties. (2) Through CNC to design seven different patterns for the back of club face, each pattern for three club head. The total amount is twenty-one. (3) Make finished product be test the characteristic time and the ability of strike by the practical measurement. (4) To analyze after the compare between three-way ANOVA and LSD. Results: After 455 stainless steel was heated in procedure S850℃-A550℃, mechanical properties became superior and had the better malleability, it is suitable for developing the club face of high spring-like effect. Before and after grinding among three-way ANOVA (pattern*thickness*place), did not achieve the significant level on the figure of characteristic time. Through two-way ANOVA (pattern*place and thickness*place), showed the significant deviation before and after grinding. After doing the crash test by 45m/s, all the results can reach the higher limited standard. Summary: 455 stainless steel was designed with the different club face’s thicknesses of fairway wood can make spring-like effect achieve high characteristic time. The much thinner club face let the characteristic time perform highly. But there was no obvious effects from the patterns of the back club face.

Mortarless refractory masonry structures are widely used in the steel industry for the linings of many high-temperature industrial applications including steel ladle. The design and the optimization of these components require accurate numerical models that consider the presence of joints as well as joints closure and opening due to cyclic heating and cooling. The present work reports on the formulation, numerical implementation, validation, and application of homogenized numerical models for simulation of refractory masonry structures with dry joints. The validated constitutive model has been used to simulate a steel ladle and to analyze its transient thermomechanical behavior during a typical thermal cycle of steel ladle. 3D solution domain, enhanced thermal and mechanical boundary conditions have been used. Parametric studies to investigate the impact of joints thickness on the thermomechanical response of the ladle have been carried out. The results clearly demonstrate that the thermomechanical behavior of mortarless masonry is orthotropic nonlinear due to gradual closure and reopening of joints with the increase and decrease of temperature. Also, resulting thermal stresses increase with the increase of temperature and decrease with the increase of joints thickness.

The effect of reprocessing on the quasi-static uniaxial tensile behavior of two commercial polypropylene (PP) based composites is experimentally investigated and modeled. In particular, the studied materials consist of an unfilled high-impact PP and a talc-filled high-impact PP. These PP composites are subjected to repeated processing cycles including a grinding step and an extrusion step to simulate recycling at the laboratory level, the selected reprocessing numbers for this study being 0, 3, 6, 9 and 12. Because the repeated reprocessing leads to thermo-mechanical degradation by chain scission mechanisms, the tensile behavior of the two materials exhibits a continuous decrease of elastic modulus and failure strain with increasing number of reprocessing. A physically consistent three-dimensional constitutive model is used to predict the tensile response of non-recycled materials with strain rate dependence. For the recycled materials, the reprocessing effect is accounted by incorporating the reprocessing sensitive coefficient into the constitutive model for Young’s modulus, failure strain, softening and hardening equations. Our predictions of true stress - true strain curves for non-recycled and recycled 108MF97 and 7510 are in a good agreement with experimental data.

Polymer flooding is an established enhanced oil recovery (EOR) method, still many aspects of polymer flooding are not well understood. This study investigates the influence of mechanical degradation on flow properties of polymers in porous media. Mechanical degradation due to high shear forces may occur in the injection well and at the entrance to the porous media. The polymers that give high viscosity yields at a sustainable economic cost are typically large, MW > 10 MDa, and have wide molecular weight distributions. Both MW and the distributions are altered by mechanical degradation, leading to changes in the flow rheology of the polymer. The polymer solutions were subjected to different degrees of pre-shearing and pre-filtering before injected into Bentheimer outcrop sandstone cores. Rheology studies of injected and produced polymer solutions were performed and interpreted together with in-situ rheology data. The core floods showed a predominant shear thickening behavior at high flow velocities which is due to successive contraction/expansion flow in pores. When pre-sheared, shear thickening was reduced but with no significant reduction in in-situ viscosity at lower flow rates. This may be explained by reduction in the extensional viscosity. Furthermore, the results show that successive degradation occurred which suggests that the assumption of the highest point of shear which determines mechanical degradation in a porous media does not hold for all field relevant conditions.

We focus on macromolecules which are modelled as sequentially growing dual scale-free networks. The dual networks are built by replacing star-like units of the primal treelike scale-free networks through rings, which are then transformed in a small-world manner up to the complete graphs. In this respect, the parameter γ describing the degree distribution in the primal treelike scale-free networks regulates the size of the dual units. The transition towards the networks of complete graphs is controlled by the probability p of adding link between non-neighbouring nodes of the same initial ring. The relaxation dynamics of the polymer networks is studied in the framework of generalized Gaussian structures by using the full eigenvalue spectrum of the Laplacian matrix. The dynamical quantities on which we focus here are the averaged monomer displacement and the mechanical relaxation moduli. For several intermediate values of the parameter’s set (γ, p) we encounter for these dynamical properties regions of constant in-between slope.

Implant-supported-screw-retained prostheses are really popular. Some of the most frequent complications have been mechanical complications. These include abutment screw loosening or even screw fracture. Using an intermediate abutment can offer several advantages. However, little literature has been found regarding how this affects the mechanical behavior of dental restorations. This study focuses on understanding the mechanical behavior of implant-supported restorations with a transepithelial component compared to those with a direct implant-supported restoration. It was carried out by using the Finite Element Method (FEM) and was experi-mentally validated. The results showed that in the case of transepithelial-supported restoration, the prosthetic screw mounted over the transepithelial component suffers higher stress than the one screwed directly to the implant. After applying a cyclic fatigue load, it is experimentally proven that, in the transepithelial-supported restorations, the fuse changes from being the screw that goes to the implant, to being the upper one. As a conclusion we can say that the use of an intermediate abutment in dental restoration not only provides better protection to the rest of the dental restoration but also allows easier repair in the event of a fracture. This can potentially lead to more efficient procedures and improved patient outcomes.

Mechanical circulatory support has proven effective in managing postcardiotomy cardiogenic shock by stabilizing patients' hemodynamics and ensuring adequate organ perfusion. Among the available device modalities, the combination of extracorporeal life support and a microaxial flow pump for left ventricular unloading has emerged as a valuable tool in the surgical arma-mentarium. In this publication, we provide recommendations for the application and weaning of temporary mechanical circulatory support in cardiogenic shock patients, derived from a con-sensus among leading cardiac centers in German-speaking countrie

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

The aim of this investigation is focused on the effects of hooked-end steel fibers on both fresh and hardened properties of modified self-compacting concretes (SCC). For this purpose, the steel fibers are associated with other residues contents (i.e. marble, granite and rubber). This concatenated materials contents constitutes a novelty since no investigations are reported. It is found that the increase of rubber content, a better ability to absorb energy is observed. This indicates that a good alternative of structural material is provided. Fresh properties are evaluated by using flow, T500 time, V-funnel, J-ring methods. The mechanical behavior is evaluated in terms of compressive strength, tensile strength, static and dynamic modulus of elasticity, and damping ratio. Experimental results of the water absorption, porosity and density are also attained. It is also found that a SCC mixture containing steel fiber, marble/granite residue and rubber content is a potential mixture to be considered when in SCC designing associated with improved damping ratio. Although the rubber content decreases the mechanical behavior and slump flow, the concatenated utilization of MGR and steel fiber contents provide a slight improve in the damping result. An environmental benefit can also be associated since the cement consumption is decreased with marble additions.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

Measurements of the properties of soft materials are important from the point of view of medical diagnostics of soft tissues as well as testing the quality of food products and many technical materials. One of the frequently used techniques for testing such materials, attractive due to its non-invasive nature, is the indentation technique, which does not puncture the material. The difficulty of testing soft materials, which affects the objectivity of its results, is related to the problems of stable positioning of the studied material in relation to the indentation apparatus, especially with a device held by the operator. This work concerns the comparison of test results using an indentation apparatus mounted in mobile and stationary handles. The tested materials are cylindrical samples of polyurethane foams with three different stiffnesses and the same samples with a 0.5- or 1-mm-thick silicone layer. The presented research uses an apparatus with a flat cylindrical indenter, with a surface area of 1 cm2, pressed to a depth of 10 mm (so-called deep tests). Based on the recorded force changes over time, five descriptors of the indentation test were determined and compared for both types of handles. The tests performed showed that the elastic properties of foam materials alone and with a silicone layer can be effectively characterized by the maximum forces during recessing and retraction, and the slopes of the recessing and retraction curves. In the case of two-layer materials, these descriptors reflect both the characteristics of the foams and the silicone layer. The results showed that the above property of the deep indentation method distinguishes it from the shallow indentation method. The repeatability of tests performed in the mobile and stationary holders were determined to be comparable.

We develop a technique for realizing lithium niobate on insulator (LNOI) waveguides of a multi-centimeter-length with a propagation loss as low as 0.027 dB/cm. Our technique relies on patterning a chromium (Cr) thin film coated on the top surface of LNOI into a hard mask with a femtosecond laser followed by the chemo-mechanical polishing for structuring the LNOI into the waveguides. The surface roughness on the waveguides is determined to be 0.452 nm with an atomic force microscope (AFM). The approach is compatible with other surface patterning technologies such as optical and electron beam lithographies or laser direct writing, enabling high-throughput manufacturing of large-scale LNOI-based photonic integrated circuits.

This paper presents the microstructural and mechanical properties of low and medium carbon advanced high-strength forging steels developed based on the third generation advanced high-strength sheet steels, in conjunction with those of conventional high-strength forging steels. Hot-forging followed by an isothermal transformation process considerably improved the mechanical properties of the forging steels. The improvement mechanisms of the mechanical properties were summarized by relating to the matrix structure, the strain-induced transformation of metastable retained austenite and/or a mixture of martensite and austenite.

In the field of metallurgy, there are many factors that influence the final quality of cast iron. These are mainly charge materials, chemical composition, metallurgical preparation up to the final casting process. Even small deviations from metallurgical processing lead to fluctuations in melt quality and the occurrence of casting defects. Charge materials has a significant impact on the quality of cast iron, especially steel scrap, which is increasingly used from an economic and ecological point of view, especially when melting cast iron in electric furnaces. Cast iron produced from a higher proportion of steel scrap in the charge has higher hardness and tensile strength. On the other side, these cast irons has a higher tendency to chillout, brittleness, shrinkage, pearlitic microstructure, stresses and higher purity due to the difference in hardness at different wall thicknesses of the castings. It is the high hardness that is the problem in the final machining of castings. These negative properties are recorded mainly in heavy thick-walled castings with higher tensile strength and hardness. This negative effect is mainly due to the nitrogen content in the steel scrap. Based on these knowledges, operating melts were realized in the foundry's operating conditions. The influence of steel scrap in the charge and the possibility of eliminating its negative effects on the properties of cast iron were investigated.

Here I describe an overlooked form of non-biological paralife (i.e., near-life) that has been evolving on Earth for millions of years, and is currently in the final stages of transitioning into a new form of life. Any consideration of non-biological life or paralife is complicated by the fact that there is no consensus among biologists for the definition of life. This ambiguity has caused disagreement about whether subcellular reproduction systems like viruses are a form of life, despite having genomes, mutations, heritable phenotypes and system-improving evolution. To resolve this problem, I develop a definition of life that is entirely functional and independent of any of the structural idiosyncrasies of biological life on Earth: an order-generating system controlled by internally-encoded information that perpetuates itself by functioning to counteract its entropic decay. Using this definition, subcellular transposons, plasmids, and viruses are paralife because they match the definition of life in all ways except that they induce their order-generating functioning by a living host rather through their own self-sustaining production system. Using this functional definition of life, I show that utility- products (UPs) like fabricated hand tools are part of induced-reproduction systems that have features equivalent to biological genomes, mutations, heritable phenotypes, and a process of system-improving evolution. The perceived benefit of utility-products causes them to induce their reproduction by a biological life-form (humans). For these reasons, human utility products are functionally just as close to being a form of life as subcellular transposons, plasmids, and viruses, i.e., they are Utility-Product paralife (UP-parlife). I also show that some forms of UP-paralife are currently evolving into mechanical life that is capable of both self- sustaining reproduction and system-improving evolution without outside assistance. This transition requires the development of a high level of factory and/or UP automation and artificial intelligence (AI) that is capable of complex reasoning, imagination and creativity. Finally, I consider the influence of UP-life and UP-paralife on the development of the level of structural complexity in the universe, and I briefly speculate about how these non-biological forms of life and paralife will influence the expansion of scientific knowledge about the universe.

In this work, a xylan-based antimicrobial additive agent was prepared and aimed for uses in paper products against Escherichia coli bacteria. The derived Cationic-Xylan-grafted-PHGH (CX-g-PHGH) was successfully synthesized by graft copolymerization of cationic-xylan with guanidine polymer (PHGH) using ceric ammonium nitrate as initiator. The obtained CX-g-PHGH had maximum PHGH grafting ratio of 18.45% and efficiency of 58.45%, and showed good viscosity and thermal stability. Furthermore, the paper samples prepared in this work were reinforced obviously with the addition of CX-g-PHGH by improved mechanical properties. Compared to the reference paper without any of the xylan-derivatives, the index of tensile, tear, burst and folding endurance of the paper had increases up to 20.07%, 25.31%, 30.20% and 77.78%, respectively. Moreover, the prepared CX-g-PHGH paper exhibited an efficient antimicrobial activity against E. coli bacterial, by which a lot of applications based on the new xylan-derived additive agent obtained in this work could be found, especially in field of antimicrobial paper products against E. Coli bacteria from contaminated food.

The parts obtained by FFF technology are anisotropic in any direction; while the whole part constitutes out of layers, each of the layers include one or more perimeters of shell and the infill with density from 0 to 100%. Mechanical performance of FFF parts depends on its shape, orientation, constitution and 3D printing parameters. A classification for shapes of parts obtained by FFF and stressed during its operation is provided. For the most questionable class (parts with interrupted shell critically stressed on interlayer boundaries) a representative sample and testing apparatus is developed. Different approaches to the sample shape modification were applied and tested. The part shape optimization resulted in increment of the force, required to fracture the part from 483 to 1096 N.

Entangled metallic wire material (EMWM) can be utilized as a novel elastic element in vibration isolation devices for mechanical actuators. This paper presents a vibration experiment aimed at investigating the degradation behavior of mechanical performance in EMWM under cyclic compressive environment. An electric vibration testing system, coupled with an isolation structure, is employed to apply compressive loads to the EMWM specimens. Through visual observations and quasi-static compression tests, the variations in geometric morphology and mechanical properties are studied, considering different relative densities and stress amplitudes. The results incidate a significant reduction in the compressed dimension of the specimens as the number of cycles increases, without any wire fractures or wear. Moreover, the mechanical properties exhibit an increasing secant modulus and a decreasing loss factor. These variations ultimately lead to a gradual deviation of the vibration characteristics of the isolation structure from its design state. To predict the mechanical property degradation of EMWM, prediction models are proposed, incorporating dimension, modulus and damping by fitting the obtained results. This research provides valuable experimental data and presents an effective method to determine the operational lifetime of vibration isolators utilizing EMWM.

Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) is developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) are comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibits a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at -20 ℃. In contrast, the HR-QT steel exhibits tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consists of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reaches 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared to the HR-QT process, the TMCP-DQP process results in finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieves the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilizes the RA through carbon enrichment, while the relaxation stage reduces a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminates internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

In this study, AlSi12 alloy was fabricated using the selective laser melting (SLM) technique to produce high density components with complex and customized parts for railway applications. Nonetheless, the production of dense samples necessitates the optimization of production process parameters. As a statistical design of experimental technique, the response surface methodology was used to optimise different combination of SLM parameters. The results were analysed using analyse of variance (ANOVA) and the signal-to-noise(S/N) ratios. The relationship between the hardness response to the process parameters (scanning speed and lase power) for determining the optimal processing conditions were examined. A hardness value of 133 HV was obtained. The process parameters were successfully optimized and the relationship between the parameters and the structures of the fabricated samples were reported.

Flexible electronics have revolutionized the field by overcoming the rigid limitations of traditional devices, offering superior flexibility and adaptability. Conductive ink performance is crucial, directly impacting the stability of flexible electronics. While metal filler-based inks exhibit excellent conductivity, they often lack mechanical stability. To address this challenge, we present a novel conductive ink utilizing a ternary composite filler system: liquid metal and two micron-sized silver morphologies (particles and flakes). We systematically investigated the influence of filler type, mass ratio, and sintering process parameters on the composite ink's conductivity and mechanical stability. Our results demonstrate that flexible wires fabricated with the liquid metal/micron silver particle/micron silver flake composite filler exhibit remarkable conductivity and exceptional bending stability. Interestingly, increasing the liquid metal content results in a trade-off, compromising conductivity while enhancing mechanical performance. After enduring 5000 bending cycles, the resistance change in wires formulated with a 4:1 mass ratio of micron silver particles to flakes is only half that of wires with a 1:1 ratio. This study further investigates the mechanism governing resistance variation during flexible wire bending. Additionally, we observed a positive correlation between sintering temperature and pressure with the conductivity of flexible wires. The significance of sintering parameters on conductivity follows a descending order: sintering temperature, sintering pressure, and sintering time. Finally, we demonstrate the practical application of this technology by integrating the composite ink-based flexible wires with conductive polymer-based strain sensors. This combination successfully achieved the detection of human movements, including finger and wrist bending.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

The UN Sustainable Development Goal 7 Report 2022 is about ensuring access to clean and affordable energy, which is key to the development of agriculture, business, communications, education, healthcare, and transportation. The lack of access to energy hinders economic and human development. Nevertheless, the current pace of progress is insufficient to achieve Goal 7 by 2030. Huge disparities in access to modern sustainable energy persist. Rising commodity, energy and shipping prices have increased the cost of producing and transporting solar photovoltaics modules, wind turbines and biofuels worldwide, adding uncertainty to a development trajectory that is already far below Goal 7 ambitions. Achieving energy and climate goals will require continued policy support and a massive mobilization of public and private capital for clean and renewable energy such as methane from biomass. An important factor in improving methane yield from biomass waste is pre-treatment of the biomass prior to anaerobic digestion. Size reduction of lignocellulose biomass is important for changing and increasing digestibility thus increasing methane yield. A Hollander beater was used as the mechanical pre-treatment machine throughout this study. Results indicate that methane yield is directly proportional to feedstock/Inoculum (F/I) ratio as higher F/I ratio led to higher methane yield. It was observed at an F/I ratio of 0.5 that 5 minutes pre-treatment time produced highest methane yield, while the lowest methane yield was observed at an F/I ratio of 0.2 with 1 minute of pre-treatment time. Methane yield decreased by 30% from 140 mL gTS-1 at F/I ratio 0.5 with 5 minutes pre-treatment time to 98 mL gTS-1 at F/I 0.2 with 5 minutes pre-treatment time. The optimum methane yield was attained at high F/I ratio allowing sufficient nutrient essential for complete degradation of biomass. Overall, this research shows the Hollander beater is not efficient in optimizing methane yield for cardboard.

In this study, seven mortar mixes were prepared by replacing natural sand by crumb rubber ,CR, (10%, 25%, 50%, 60%, 75% and 100%). The properties of mortars, both in their fresh and hardened states, were studied. Key characterisitcs, including density, water absorption coefficient, porosity, thermal conductivity, heat capacity, shrinkage/swelling, elastic modulus, compressive strength, flexure strength, fracture energy and performance after exposure to heat, were evaluated. The results obtained showed that as the CR fraction increased, density, initial setting time, and workability decreased but mortars with CR fractions ranged between 25% and 50% are lightweight and can be used for repairing as they fulfill satndards. It was observed that strengths and stiffness decreased with higher CR content while shrinkage increased for CR percentage higher than 60%. However, up to 50% of CR content the mortars obey to the standards for repair. Interestingly, incorporating up to 50% waste tires proved to improve comfort and thermal resistance without affecting thermal inertia. A slight increase in the mass loss is observed when mortars are exposed to high temperatures. Mortars containing CR between 25% and 50% can be classified as lightweight and thermally insulating mortars, suitable for repairing concrete structures in accordance with industry standards.

To improve the adaptability of aerial reflective opto-mechanical structures to low-temperature environments, an optimized thermal control design is proposed. Firstly, the relationship be-tween conventional heating methods and axial/radial temperature differences of mirrors with different shapes is analyzed. Based on heat transfer analyses, it is pointed out that optimized thermal control design is necessary to ensure the temperature uniformity of the fused silica mirror and take into account the temperature level when working in low temperature environ-ments. A thermal control scheme based on temperature negative feedback variable power zone heating is proposed for the characteristics of aerial electro-optics systems. Using the thermal control scheme at low temperatures ensures that the average temperature of the mirror fluctu-ates slowly and slightly around 20℃. At the same time, the temperature differences within a mirror and between the primary mirror and the secondary mirror can be controlled within 5℃. Thereby, satisfactory image quality is obtained.

The paper presents research results on biocomposites made from a combination of extruded apple pomace (EAP) and potato starch (SP). The products were manufactured by hot pressing using a hydraulic press with a mold for producing samples. The prepared biocomposites were subjected to strength tests, surface wettability was determined and color analysis was carried out. Thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR) and cross section observed in Scanning electron microscope (SEM) were also performed. The obtained test results showed that the combination of apple pomace (EAP) and starch (SP) enabled the production of compact bicomposite materials. At the same time, it was found that each increase in the share of starch in the mixture for producing biocomposites increased the strength parameters of the obtained materials. With the highest share of starch in the mixture, 40%, and a raw material moisture content of 14%, the material had the best strength parameters and was even characterized by hydrophobic properties. It was also found that materials with a high content of starch are characterized by increased temperature resistance. Analysis of SEM microscopic photos showed well-glued particles of apple pomace, pectin, gelatinized starch and a smooth external structure of the samples. Research and analyzes have shown that apple pomace reinforced only with the addition of starch can be a promising raw material for the production of simple, biodegradable biocomposite materials.

Advancements in 3D printing technologies have led to new implementations in rapid prototyping, microfluidics, tooling, dentistry, biomedical devices, drug delivery, and tissue engineering. Stereolithography techniques, which are photopolymerization-based processes, contribute to the optical, chemical, and mechanical properties of 3D printed materials using versatile polymer chemistry. This study used potassium titanate powder (K2Ti8O17) as an additive to enhance the mechanical strength of photocurable resins. PEG was selected as the stabilizer to optimize the dispersion and precipitation of potassium titanate. The flexural strength, hardness, and tensile strength were compared to assess the mechanical strength of the 3D printing resin. The flexural strengths of the printed specimens were in the range of 15–39 N/mm2. The measured surface hardness and tensile strength were 41–80 HV and 2.3–15 N/mm2, respectively. The output resolution of the potassium titanate/acrylate resin was tested using a line-pattern structure. 3D printing resin without stabilizers produced lines with a thickness of 0.3 mm, whereas 3D printing resin containing a stabilizer produced lines with a thickness of 0.2 mm. The flexural strength and pattern thickness results suggest that the potassium titanate/acrylate resin can be utilized as a 3D printer resin, suggesting new possibilities for potassium titanate materials.

In recent times, the soft robotics field is gaining numerous research focus owing to its high level of manipulation capabilities unlike traditional rigid robots, which gives room for an increasing use in other areas. However, compared to traditional rigid gripper robots, being capable of controlling/obtaining overall body stiffness when required is yet to be further explored since soft gripper robots have inherently less rigid properties. unlike previous designs with very complex variable stiffness systems, this paper demonstrates a soft gripper design with minimum system complexity while being capable of varying the stiffness of a continuum soft robotic actuator and proves to have potential applications in gripping objects of various shapes, weights &amp; sizes. The soft gripper actuator comprises two separate mechanisms; the pneumatic mechanism for bending control and the mechanical structure for stiffness variation by pulling tendons using stepper motors which compresses the actuator, thereby changing the overall stiffness. The pneumatic mechanism was first fabricated and then embedded into another silicon layer during which it was as well merged with the mechanical structure for stiffness control. By first pneumatically actuating the actuator which causes bending and then pulling the tendons, we found out that the actuator stiffness value can be increased up to 145 % its initial value, and the gripper can grasp &amp; lift a weight of up to 2.075 kg.

The study of mechanical properties of rock mass can be effectively carried out through rock-like material model test. The similarity of mechanical properties between rock-like material and protolith is dependent on the appropriate selection of composition and content of rock-like materials. In this research, X-Ray diffraction test was conducted to analyze the composition of deep rock, which confirmed silica, quartz, and dolomite as the primary components of deep sandstone. An orthogonal design test was used to execute the ratio test of rock-like material. River sand was used as an aggregate, cement as a binder, gypsum powder as a regulator, and polystyrene foam (EPS) as rock damage simulation material. The influencing factors considered in the orthogonal mechanical tests were the proportion of aggregate and binder, ratio of binder and regulator, quantity of damage simulation material, and size of damage simulation material. Three levels were set for each factor, and mechanical parameters such as compressive strength, tensile strength, elastic modulus, axial strain, and Poisson's ratio were tested for each group of samples. The changes of those parameters with the levels of the above four factors were studied. The study revealed that adjusting the size of polystyrene foam (EPS) can adjust the values of elastic modulus, tensile strength, and Poisson's ratio of rock-like material. Similarly, changing the ratio of binder and regulator can adjust the values of axial strain and compressive strength of rock-like material. The rock-like material developed in the study can simulate the mechanical properties of different rock masses such as granite, sandstone, shale, and limestone.

The effects of post-treatment temperature-based methods on 1D single PLA filaments after FFF have been studied. This lets to decouple the variables related to the 3D structure (layer height, raster angle, infill density, and others) from the variables solely related to the material (molecular weight, molecular orientation, crystallinity, and others). PLA 1D filaments have been aged at 20, 39, 42, 51, 65, 75 and 80 ºC in a water-bath-inspired process in which the hydrolytic degradation of the PLA has been minimised for the ageing temperatures of interest. The evolution of the thermal and mechanical properties of the PLA filaments at different temperatures was recorded. Differential scanning calorimetry (DSC) was used to evaluate thermal and physical properties, in which the glass transition, enthalpic relaxation, crystallisation and melting reactions were analysed. Tensile tests were performed to evaluate the tensile strength and elastic modulus. The flow-induced molecular orientation, the degradation, the logistic fitting and the so-called summer effect –stabilisation of properties at higher temperatures– are discussed for assessing the safeness of accelerating ageing.

The effects of residual stress in a tungsten gate on a polysilicon channel in scaled 3D NAND flash memories were investigated using a technology computer-aided design simulation. The NAND strings with respect to the distance from the tungsten slit were also analyzed. The scaling of the spacer thickness and hole diameter induced compressive stress on the polysilicon channel. Moreover, the residual stress of polysilicon in the string near the tungsten slit had greater compressive stress than the string farther away. The increase in compressive stress in the polysilicon channel degraded the Bit-Line current (Ion) because of stress-induced electron mobility deterioration. Moreover, a threshold voltage shift (△Vth) occurred in the negative direction because of conduction band lowering.

The gastrointestinal (GI) tract is a continuous channel through the body that consists of the esophagus, the stomach, the small intestine, the large intestine, and the rectum. Its primary functions are to move the intake of food for digestion before storing and ultimately expulsion of feces from the rectum through the anal sphincter. The mechanical behavior of GI tissues thus plays a crucial role for GI function in health and disease. The mechanical properties are typically characterized by a constitutive biomechanical model, which is a mathematical representation of the relation between load and deformation in a tissue. Hence, validated biomechanical constitutive models are essential to characterize and simulate the mechanical behavior of the GI tract under physiological and pathological conditions. Numerous constitutive models have consequently been proposed over the past three decades, mainly inspired by work done in cardiovascular tissues. Here, a comprehensive review of these constitutive models is provided. This review is limited to studies where a model of the strain energy function is proposed to characterize the stress-strain relation of a GI tissue. Several needs are identified for more advanced modeling of GI biomechanics including: 1) Microstructural models that provide actual structure-function relations; 2) Validation of coupled electro-mechanical models accounting for active muscle contractions; 3) Human data under physiological and pathological conditions to develop and validate models. The findings from this review provide guidelines for using existing constitutive models as well as perspective and directions for future studies aimed at establishing new constitutive models for GI tissues.

An infestation of parkinsonia (Parkinsonia aculeata) located on Alexandria Station, Northern Territory, Australia was successfully treated with a bioherbicide using stem implanted capsules. The bioherbicide containing three endemic endophytic fungi (Lasiodiplodia pseudotheobromae, Macrophomina phaseolina and Neoscytalidium novaehollan-diae) is the first Australian registered woody weed bioherbicide. The product was effectively administered to the plant stems using a mechanical device, resulting in subsequent development of a dieback event, which, after a period of establishment, has moved through the adjacent untreated plant population resulting in significant decline in infestation vigour and reduced recruitment. This is the first report of large-scale management of parkinsonia by this method.

This paper presents the values of several mechanical characteristics for two blends: H (60% PP + 12% PA6 + 8% EPDM + 20% Polybond 3200) and G (20% PP + 42% PA6 + 28% EPDM + 10% Polybond 3200) (%wt), comparing them to those of PP (polypropylene) and PA6 (polyamide 6). The adding of EPDM (ethylene propylene diene monomer rubber) and Polybond 3200 help reducing the disadvantages of simple blends made of PP+PA6, when the PA6 concentration allows for having a PA6 matrix with droplets of PP. SEM analysis helps for understanding the performance of material G as compared to the neat polymers. EDX analysis proved that there was a matrix inversion, material H having a PP matrix and material G a matrix made of PA6 with droplets of PP. Strain at break for PP and material H were proved to be insensitive to test speed, but materials G and PA6 had large value for strain at break and energy at break for v = 10 mm/min. Taking at basis the values for polyamide 6 (PA6), material G has greater values for energy at break: with 97.8% for v = 10 mm/min, with 29.5% for v= 250 mm/min and with 98% for 1000 mm/min, without exhibiting the micro and macro cavitation of PA6. This means that the recipe, the technology and the mechanical characteristics make material G a potential candidate for applications where a low and moderate impact resistant material is required.

This study aims to identify an optimal heat-treatment parameter set for an additively manufactured AlSi10Mg alloy in terms of increasing the hardness and eliminating the anisotropic microstructural characteristics of the alloy in as-built condition. Furthermore, the influence of these optimized parameters on the fatigue properties of the alloy investigated. In this respect, microstructural characteristics of an AlSi10Mg alloy manufactured by Laser-Based Powder Bed Fusion in non-heat-treated and heat-treated conditions were investigated. Their static and dynamic mechanical properties were evaluated, and fatigue behavior was explained by a detailed examination of fracture surfaces. Much of the microstructure in the non-heat-treated condition was composed of columnar grains oriented parallel to the build direction. Further analysis revealed a high fraction of pro-eutectic α-Al. Through heat-treatment, the alloy was successfully brought to its peak-hardened condition, while eliminating the anisotropic microstructural features. Yield strength and ductility increased simultaneously after heat-treatment, which is due to the relief of residual stresses, preservation of refined grains, and introduction of precipitation strengthening. The fatigue strength, calculated at 10^7 cycles, improved as well after heat-treatment and finally detailed fractography reviled that a more ductile fracture mechanism has happened in the heat-treated condition compared to the non-heat-treated condition.

Currently, one of the biggest issues when developing an ODS alloy is the competition established between the different oxide precursors during the precipitation of oxides which nature depends on their chemical composition. In the presence of various precursors, usually the one with the highest affinity to oxygen leads to the absence of the other oxides. In this work, a new process to equilibrate the local concentration of species and to decrease the competition among them is explained. A unique compound, containing the diverse oxide precursors as one complex oxide, is introduced in a prealloyed 14Cr Steel powder via mechanical alloying. Thus, generating environments enriched in Y, Ti and Zr which, after consolidation, refine the oxides precipitation improving the thermal stability of the alloy. SPS were used as consolidation technique to guarantee shorter sintering times and to maintain the nanostructure obtained. Mechanical properties were tested by tensile tests and Vickers microhardness.

Background - Physiological helical flow in the ascending aorta has been well documented in the last two decades, accompanied by discussions on possible physiological benefits of such axial swirl. Recent 4D-MRI studies on healthy volunteers have shown indication of early generation of helical flow, early in the systole and already close to the valve plane. Objectives - Firstly, the aim of the study is to investigate the hypothesis of premature swirl existence in the ventricular outflow tract leading to already helical flow in the valve plane, and second to investigate the possible impact of two different mechanical valves design on the preservation of this early helical flow and its subsequent hemodynamic consequences. Methods - We use a pulse duplicator with an aortic arch and High Speed Particle Image Velocimetry to document the flow evolution in the systolic cycle. The pulse-duplicator is modified with a swirl-generating insert to generate early helical flow in the valve plane. Special focus is laid on the interaction of such helical flow with different designs of mechanical prosthetic heart valves, comparing a classical bileaflet mechanical heart valve, the St Jude Medical Regent valve (SJM Regent BMHV) with the Triflo trileaflet mechanical heart valve T2B version (Triflo TMHV). Results – When the swirl-generator is inserted, a vortex is generated in the core flow demonstrating early helical flow in the valve plane, similar as observed in the recent 4-D-MRI study taken for comparison. For the Triflo trileaflet valve, the early helical flow is not obstructed in the central orifice, similar as in the case of the natural valve. Conservation of angular momentum leads to radial expansion of the core flow and flattening of the axial flow profile downstream in the arch. Furthermore, the early helical flow helps to overcome separation at the outer and inner curvature. In contrast, the two parallel leaflets for the bileaflet valve impose a flow straightener effect, annihilating the angular momentum with negative impact on kinetic energy of the flow. Conclusion - The results imply better hemodynamics for the Triflo trileaflet valve based on hydrodynamic arguments under the discussed hypothesis. In addition, it makes the Triflo valve a better candidate for replacements in patients with pathological generation of nonaxial velocity in ventricle outflow tract.

The purpose of this study was to develop a mathematical model for non-contacting face seals to analyze how their performance is affected by thermoelastic phenomena. The model was used to solve thermal conductivity and thermoelasticity problems. The primary goal was to calculate the values of thermal deformations of the sealing rings in a non-contacting face seal with a flexibly mounted rotor (FMR) for a turbomachine. The model assumes conversion of mechanical energy into heat in the fluid film. The heat flux generated in the fluid film is transferred first to the sealing rings and then to the fluid surrounding them. An asymmetric distribution of temperature within the sealing rings leads to the occurrence of thermal stresses and, consequently, a change in the rings geometry. The model is solved analytically. The distributions of temperature fields for the sealing rings in the cross-sections are calculated using the Fourier-Bessel series as a superficial function of two variables (r,z). The thermoelasticity problems described by the Navier equations are solved by applying the Boussinesq harmonic functions and Goodier’s thermoelastic displacement potential function. The proposed method involves solving various theoretical and practical problems of thermoelasticity in FMR-type non-contacting face seals. The calculated thermal deformations of the sealing rings are used to determine the most important seal performance parameters such as the leakage rate and power loss.

In this paper, we aim to assess the electric current parameters and report the analysis of the associated degree of ventricular recovery during left ventricular assist device (LVAD) support. An assumption was made there is a linear relationship between ventricular recovery degree and the pump electric current pulsatility index (PI). The experimental study was carried out using the ViVitro Pulse Duplicator System with Sputnik 1 LVAD connected. Cardiac output (CO) and cardiac power output (CPO) were used as a measure of ventricular recovery degree. Different heart rates (HR) (59, 73, 86 bpm) and pump speeds (7600–8400 rpm in 200 rpm steps) were investigated. Ventricular stroke volumes in the range of 30–80 ml for each heart rate at certain pump speed were used. The obtained relationships of CO and CPO vs. PI was linear as the coefficients of determination for each regression curve were more than 0.8. CO vs. PI: R2=0.9218; 0.9271; 0.9172 and CPO vs. PI: R2=0.8517; 0.841; 0.8244 for HR=59 bpm; 73 bpm; 86 bpm, respectively. Study findings suggest that adequate interpretation of parameters could potentially serve as a valuable clinical tool to assess ventricular recovery based on LVAD infrastructure without requiring any special hemodynamic assessment.

Extensive experimental and theoretical research over the past several decades has culminated in the understanding of the mechanisms behind nanoparticle-mediated enhancements on the mechanical properties of hydrogels. This information is not only crucial to realizing applications that directly benefit from developing hydrogels with high mechanical strength, but also to guide the development of strategies to further enhance hydrogel properties by combining different approaches. In our study, we investigated the effect of combining two approaches – addition of nanoparticles and crosslinking two different polymers (to create double-network hydrogels) – on the mechanical properties of hydrogels. Our studies revealed that these approaches may be combined to synthesize hydrogel composites with enhanced properties; however, both polymers in the double-network hydrogel must strongly interact with the nanoparticles to fully benefit from the addition of nanoparticles. Moreover, the concentration of hydrogel monomers used for the preparation of the double-network hydrogels had a significant effect on the extent of nanoparticle-mediated enhancements; double-network hydrogel nanocomposites prepared using lower monomer concentrations showed higher enhancements in elastic moduli compared to those prepared using high monomer concentrations. Collectively, these results demonstrate that the hypotheses previously developed to understand the role of nanoparticles on the mechanical properties of hydrogel nanocomposites may be extended to double-network hydrogel systems and guide the development of next generation hydrogels with extraordinary mechanical properties through a combination of orthogonal approaches.

The article presents a mathematical model to investigate the operability envelopes for subsea production tress (SPT) installation using drill pipe. The finite differential method was used to solve the established governing equations in which the ocean conditions were considered. Based on the evaluations of the ocean wave, ocean current, water depth, specification of drill pipe and SPT weight that might dominate the mechanical behaviors of the pipe, the operability envelopes with permissible ocean conditions for SPT installation were obtained. The results indicate that changes of depths in deep water and SPT weight have few effects on the operation conditions and it would be better to choose smaller pipe to obtain larger permissible ocean conditions during SPT installation.

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice.

Failure characteristics induced by unloading disturbance and the corresponding mechanical mechanism of the coal seam floor are important theoretical bases for water-bursting prevention from the floor of the coal seam and rock burst alarm in deep mining. However, the existing two-dimensional ground-pressure-control theory based on shallow mining cannot sufficiently guide deep-mining practices. In this study, the redistribution of mining-induced stress field in rocks surrounding the longwall face and mechanical behaviors of strata in deep mining are investigated through a combination of numerical simulation, physical simulation, and field measurement. Results demonstrate that mining-induced stress fields in the floor of the longwall face differ in space and time. Vertical stress unloading from top to bottom of the floor and horizontal stress unloading are relatively low. A concentration zone of high horizontal stress exists at stope boundaries. The critical yield load of rock stratum in the floor is determined through thin plate yield theory. Under the combined effect of concentrated high horizontal and vertical resilience stresses, strata in the floor fracture from seam to seam if the load increases to the minimum critical buckling value. Fractured strata slide along the fracture surface, which leads to floor heave. The stope floor shows evident time-delay progressive failure characteristics. The stress shell in the stope floor in deep mining is found to be a sensitive mechanical parameter that produces three-dimensional ground-pressure behavior in the floor. This ground-pressure behavior in the stope floor is controlled by the existence of the corresponding stress shell and effects induced by its space–time evolution. This study provides theoretical basis for the dynamic control of a hazard-inducing environment in engineering and minimizing or altering disaster-occurrence conditions during the construction engineering of the coal seam floor.

The prohibitive costs of small-scale solar photovoltaic (PV) racks decreases PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt mounted racking designs that allow manual change of tilt angle from zero to 90 degrees by varying the length of cables. The racks are designed using the calculated dead, wind and snow loads for Canada as conservative design for most of the rest of the world. Structural capacities of the wooden members are then ascertained and resisting bending moment, shear force, tensile force, and compressive force for them is calculated. A structural and truss analysis is performed to ensure that racking design with-stands the applicable forces. Moreover, implications of changing the tilt angle on the wooden members/cables used to build the system are also determined. The systems offer significant economic savings ranging from 1/3rd to 2/3rd the capital expenses of the commercially available alternatives. In addition, the racking designs are easy-to-build and require minimal manufacturing operations, which increases their accessibility. The stilt-mounted designs can be employed for agrivoltaic settings while allowing farm workers shaded ergonomic access to perform planting, weeding, and harvesting.

There is an increase towards reducing the weight of structures through the use of aluminium alloys in different industries like aerospace, automotive, etc. This growing interest would lead towards using dissimilar aluminium alloys which would require welding. TIG and friction stir welding are the well-known techniques that are currently suitable for joining dissimilar aluminium alloys. The welding of dissimilar alloys has its own dynamics which impact on the quality of the weld. This then suggests that there should be a process which can be used to improve the dissimilar alloys welds post their production. Friction stir processing is viewed as one of the techniques that could be used to improve the mechanical properties of the material. This paper reports on the status and the advancement of FSW, TIG and FSP technique. It further looks at the variation use of FSP on TIG and FSW welded joints with the purpose of identifying the knowledge gap.

Using polymethylmethacrylate (PMMA) bone cement is widespread in orthopedic surgeries for implant fixation and as a carrier for antibiotic delivery to prevent and treat infections. This review comprehensively evaluates in vitro studies investigating the antibiotic elution profiles and mechanical properties of PMMA bone cement. We explore the kinetics of antibiotic release, factors influencing elution efficiency, and the impact of various antibiotics on the mechanical properties of PMMA composites. At the same time, we examine how the inclusion of antibiotics affects the mechanical integrity of PMMA, including parameters such as compressive strength, tensile strength, and fatigue resistance. Through a detailed analysis of these studies, this review aims to provide insights into optimizing PMMA bone cement formulations for enhanced therapeutic efficacy and structural performance.

A potassium bromide KBr material, which has been widely used as the key element in the Fourier spectrometers and as the output window of the IR-lasers, has been studied with good advantage via applying the carbon nanotubes in order to modify the potassium bromide surface. The laser oriented deposition method has been used to place the carbon nanotubes at the matrix material surface in the vertical position at the different electric field varied from 100 to 600 V×cm-1. The main idea of the improvement of the spectral properties of the potassium bromide structure is connected with the fact that the refractive index of the carbon nanotubes is substantially less than the refractive index of the studied material, and the small diameter of the carbon nanotubes allows one to embed these nano-objects in the voids of the lattice of the model matrix systems. Moreover, the mechanical characteristics and wetting features of the potassium bromide structures have been investigated under the condition mentioned above. Analytical and quantum-chemical simulations have supported the experimental results.

Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

Contact inhibition (CI) represents a crucial tumor-suppressive mechanism responsible for controlling the unbridled growth of cells, thus preventing the formation of cancerous tissues. CI can be further categorized into two distinct yet interrelated components: CI of locomotion (CIL) and CI of proliferation (CIP). These two components of CI have historically been viewed as separate processes, but emerging research indicates that they share both distinctive and common pathways. Moreover, they exhibit intriguing intersections with mechanotransduction, a process that involves cells sensing and responding to mechanical forces. This review article describes the intricate interplay between mechanical forces and CI, shedding light on how these forces regulate CIL and CIP. Emphasis is placed on filamin A (FLNA)-mediated mechanotransduction, elucidating how FLNA senses mechanical forces and translates them into crucial biochemical signals that regulate cell locomotion and proliferation. In addition to FLNA, trans-acting factors (TAFs) emerge as sensitive players in both CI and the mechanotransduction process. This article presents methods for identifying these TAFs and profiling the associated changes in chromatin structure, offering valuable insights into CI and mechanotransduction regulation. Finally, it addresses unanswered research questions in these fields and delineates their possible future directions.

The high demand for lithium (Li) relates to clean renewable storage devices and the advent of electric vehicles (EVs). The extraction of Li ions from aqueous media calls for efficient adsorbent materials with various characteristics, such as good adsorption capacity, good selectivity, easy isolation of the Li-loaded adsorbent, and good recovery of the adsorbed Li ions. The widespread use of metal-based adsorbent materials for Li ions extraction relates to various factors: (i) the ease of preparation via inexpensive and facile templation techniques, (ii) excellent selectivity for Li ions in a matrix, (iii) high recovery of the adsorbed ions, and (iv) good cycling performance of the adsorbents. However, the use of nano-sized metal-based LISs is limited due to challenges associated with isolating the loaded adsorbent material from the aqueous media. Adsorbent granulation process employing various binding agents (e.g., biopolymers, synthetic polymers, and inorganic materials) affords functional particles with modified morphological and surface properties that support easy isolation from the aqueous phase upon adsorption of Li ions. Biomaterials (e.g., chitosan, cellulose, alginate, and agar) are of particular interest because their structural diversity renders them amenable to coordination interactions with metal-based LISs to form 3D microcapsules. The current review highlights recent progress in the use of biopolymer binding agents for the granulation of metal-based LISs, along with various crosslinking strategies employed to improve the mechanical stability of the granules. The study reviews the effects of granulation and crosslinking on adsorption capacity, selectivity, isolation, recovery, cycling performance and the stability of the LISs. Adsorbent granulation using biopolymer binders has been reported to modify the uptake properties of the bio-adsorbent materials to varying degrees, in accordance with the surface and textural properties of the binding agent. The review further highlights the importance of granulation and crosslinking for improving the extraction process of Li ions from aqueous media. This review contributes to manifold areas related to industrial application of LISs, as follows: 1) to highlight recent progress in the granulation and crosslinking of metal-based adsorbents for Li ions recovery, 2) to highlight the advantages, challenges, and knowledge gaps of using biopolymer-based binders for granulation of LISs, and finally, 3) to catalyze further research interest into the use of biopolymer binders and various crosslinking strategies to engineer functional adsorbent materials for application in Li extraction industry. Properly engineered extractants for Li ions are expected to offer various cost benefits in terms of capital expenditure, percent Li recovery, and reduced environmental footprint.

Exploring the fundamental mechanisms of locomotion extends beyond mere simulation and modeling. It necessitates the utilization of physical test benches to validate hypotheses regarding real-world applications of locomotion. This study introduces cost-effective modular robotic platforms designed specifically for investigating the intricacies of locomotion and control strategies. Expanding upon our prior research in Electric-Pneumatic Actuation (EPA), we present the mechanical and electrical designs of the latest developments in the EPA robot series. These include EPA Jumper, a human-sized segmented monopod robot, and its extension EPA Walker, a human-sized bipedal robot. Both replicate the human weight and inertia distributions, featuring co-actuation through electrical motors and pneumatic artificial muscles. These low-cost modular platforms, with considerations for degrees of freedom and redundant actuation, 1) provide opportunities to study different locomotor subfunctions— stance, swing, and balance; 2) help investigate the role of actuation schemes in tasks such as hopping and walking; and 3) allow testing hypotheses regarding biological locomotors in real-world physical test benches.

In 1911, A. Einstein suggested that gravity affects at the electromagnetic radiation originating from the distant sources, namely, it shifts the spectral lines in the red side of the spectrum and derived the gravitational redshift formula. A modern science claims that Einstein’s formula is mathematically immaculate. We show that this is not true: in fact, this formula is approximate. Using the law of conservation of mechanical energy, we derived two exact formulas оf the gravitational redshift.

A CoCrFeNiNb0.65 eutectic high-entropy alloys (EHEAs) prepared by arc melting were irradiated with a 100 keV He+ ion beam. Swelling, helium bubbles and mechanical response induced by irradiation were evaluated. When the ion fluence reached 1.0×1018 ions/cm2, the irradiation-induced swelling occurred on the sample surface, and as the ion fluence increasing, the swelling became increasingly severe and the surface of Nb-rich phase appeared peeling and shedding. Meanwhile, along the boundaries of matrix and Nb-rich phase there was a neat line of helium bubbles. The size of these helium bubbles decreased with distance from the center of the helium bubble layer. This result indicated that the phase boundaries were favorable sites for the nucleation and gathering of helium bubbles. Nanoindentaion results indicated that hardening and softening induced by He+ ion irradiation occurred in various ion fluences. At ion fluence of 5.0×1017 ions/cm2, the CoCrFeNiNb0.65 EHEAs exhibited an obvious hardening behavior, which can be explained by dislocation-dominated hardening effect. When the ion fluence reached 1.0×1018 ions/cm2 and 2.0×1018 ions/cm2, the hardening effect decreased probably due to the helium bubble aggregation and growth, as well as helium bubbles induced noncompact structures. The results of this study provide insights into the effect of helium bubbles on mechanical evolution and pave the way for designing EHEAs suitable for the nuclear industry.

This study investigates the influence of the porous structure, on the density and the mechanical behaviour of new foam concretes incorporating hemp shives. A total of eight batches of foam concretes were manufactured and tested, made with a protein-based foam agent, containing cement, ground granulated blast furnace slag and Metakaolin as binder and hemp shives as natural aggregate. The effect of several parameters is studied, elaboration method (direct and preformed), amount of pozzolanic additions (0% and 30%) and incorporation of hemp shives (5 and 15 vol%) on the resulting physical properties, microstructure, porous structure and mechanical behaviour of the concretes. Hemp shives incorporation results in increased concrete porosity and air bubble radius, decreased uniformity and mechanical strength, and lower cohesion with the cement matrix compared to standard concretes.

Background: For the treatment of bone defects, biodegradable compressive biomaterials are needed as a substitute, which degrade at the same rate as the bone regenerates. In this study, the compressive strength of CPC ceramics (with a layer thickness of more than 12 layers) should be compared with sintered ceramics. Methods: Round scaffolds with 20, 25, 30 and 45 layers were 3D printed the 3D Bioplotter, solidified in a water-saturated atmosphere for 3 days and then tested for compressive strength together with a sintered ceramic using a Zwick universal testing machine. Results: The 3D printed scaffolds are more compressive at 41.56 ± 7.12 MPa than the sintered ceramic at 24.16 ± 4.44. Conclusions: The round geometry sintered ceramics approach or exceed the upper limit of the compressive strength of cancellous bone in the direction of compacta (depending on the author).

In order to understand the impact of lithologic heterogeneity of continental mixed fine-grained sedimentary rocks on reservoir brittleness in western Qaidam basin, the mechanical properties of the rocks and their correlation with mineral composition and petrographic characteristics were studied by measns of mineralogy, petrography and triaxial stress test. The results show that the reservoir rocks can be divided into 5 different types according to the mechanical properties of the reservoir (characteristics of stress-strain curves), among them Type I and III belong to similar elastoplastic failure model, type II shows a special pulse failure mode for plastic material, type IV shows a failure mode of mixed characteristics, and type V exhibits a typical plastic failure model. The correlation between minerals and mechanical properties indicates that quartz and feldspar, which are often considered brittle minerals, do not contribute much to the brittleness of continental fine-grained sedimentary rocks. The main minerals affecting reservoir brittleness are dolomite and clay minerals, and their contributions to reservoir brittleness are positive and negative, respectively. The petrographic analysis results prove that the abnormal correlation between rock mechanical properties and quartz and feldspar is caused by the different rock fabrics. When dolomite forms a rock skeleton, it typically exhibits greater strength, brittleness and physical properties than other minerals. Based on the results, a brittleness evaluation standard for continental fine-grained sedimentary rock reservoir is proposed, and the validity of the standard is verified by the spatial correlation between the lithology probability model and the micro-seismic monitoring data, indicating that the spatial heterogeneity of dolomite-rich rock is the main controlling factor for the development of ‘sweet spot’ in the Cenozoic continental fine-grained sedimentary rock reservoir in the Western Qaidam Basin.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

The mechanical properties and stability of hydrophobic surface structures prepared by traditional methods are still the main technical bottlenecks restricting the broad application of hydrophobic systems on workpiece surfaces. In this contribution, we propose a technique called selective laser shock peening (SLSP) to enable large-scale high efficient, low-cost manufacturing of hydrophobic metal surfaces with enhanced mechanical properties for durable applications. Using the method of experimental investigation combined with numerical calculation, the hydrophobic properties, mechanical properties, and tribological properties of the samples prepared under SLSP, all-laser shock peening (ALSP), and non-laser shock peening (NLSP) are studied. The SLSP process could prepare a 3D gradient structure material with surface structures, a two-phase (strong phase, soft phase) distribution on the surface, and a multi-level gradient distribution in the thickness direction. Compared with the 2D gradient structure prepared by the traditional process, 3D gradient structures by SLSP have more significant advantages in improving the wetting behavior and the mechanical properties of the material, which proves SLSP to be a novel method to fabricate functional metal surface structures, with highly high engineering application value.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

Existing rammed earth construction methods have disadvantages such as increased initial costs for manufacturing the large formwork and increased labor costs owing to the labor-intensive construction techniques involved. To address the limitations of existing rammed earth construction methods, an autonomous rammed earth construction method is introduced herein. As this autonomous rammed earth construction method uses a modular formwork, alternative materials must be used in the construction to satisfy the requirements for the early-age binder performance. Accordingly, this study evaluates the use of an epoxy emulsion composed of epoxy and a hardener to enhance the performance of the binder. Preliminary experiments were conducted to determine the optimal formulation of the epoxy emulsion, following which the compressive strength, water loosening, shrinkage, rate of mass change, and microstructure of several red clay binder specimens with and without epoxy emulsion were analyzed at early ages. The results confirmed that the epoxy emulsion can be applied to satisfy the performance requirements for autonomous rammed earth construction by improving the durability and strength of the binder at early ages.

Mucosal irritation caused by cusps of upper and lower teeth represents a source of persistent, low grade mechanical trauma. This type of trauma can initiate and/or perpetuate oral lichen planus in a few susceptible patients. Here, we report a rare case of bilateral white linear striations in the buccal mucosa of a young patient, associated with sharp cusps. Oral lesions demonstrated a unique cuspal signature highlighting the causal role of subtle mucosal trauma in the genesis of reticular-oral lichen planus. Lesions appeared to be exacerbated by significant psychological distress experienced by the patient. Although the Koebner phenomenon is well reported in the cutaneous lichen planus literature, such presentations are relatively rare in the oral cavity. This report emphasizes the potential role of low-grade cuspal trauma/irritation in conjunction with psychological distress in the genesis of oral lichen planus.

There is currently an interest in “active” implantable biomedical devices that include mechanical stimulation as an integral part of their design. This paper reports the experimental use of a porous scaffold made of interconnected networks of slender ferromagnetic fibres that can be actuated in vivo by an external magnetic field applying strains to in-growing cells. Such scaffolds have been previously characterized in terms of their mechanical and cellular responses. In this study, it is shown that the shape changes induced in the scaffolds can be used to promote osteogenesis in vitro. In particular, immunofluorescence, gene and protein analyses reveal that the actuated networks exhibit higher mineralization and extracellular matrix production, and express higher levels of osteocalcin, alkaline phosphatase, collagen type 1a1, runt-related transcription factor 2 and bone morphogenetic protein 2 than the static controls at the 3-week time point. The results suggest that the cells filling the inter-fibre spaces are able to sense and react to the magneto-mechanically induced strains facilitating osteogenic differentiation and maturation. This work provides evidence in support of using this approach to stimulate bone ingrowth around a device implanted in bone and can pave the way for further applications in bone tissue engineering.

By using hydrogen quench continuous annealing technology, Stelco Inc. has developed a suite of Advanced High Strength Steel (AHSS) grades with tensile strength greater than 1000MPa to meet standard automotive specifications and for unique customer requirements. These grades were optimized by correlating chemical composition and processing parameters with microstructures and mechanical properties. Dual-Phase 980 (Stelco trademarked STELMAXTM 980DP), Multi-Phase 1180 (STELMAXTM 1180MP), Martensitic Steel 1300 (STELMAXTM 1300M) and 1500 (STELMAXTM 1500M) products met strength and formability requirements with excellent flatness and surface quality. Hydrogen quench continuous annealing technology not only ensures all developed AHSS grades have consistent mechanical properties across the entire strip length (from strip head to tail) and width (from edge to edge), but also produces high product yield compared with other continuous annealing processes.

We demonstrate fabrication of single-mode optical waveguides on lithium niobate on insulator (LNOI) by optical patterning combined with chemo-mechanical polishing. The fabricated LNOI waveguides have a nearly symmetric mode profile of a mode field size of ~2.5 µm (full-width at half maximum). We develop a high-precision measurement approach by which the single mode waveguides are characterized to have a propagation loss of ~0.042 dB/cm.