Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

Purpose: To improve numerical simulation of the non-contact tonometry test by using Arbitrary Eulerian-Lagrangian deforming mesh in the coupling between computational fluid dynamics model of an air jet and finite element model of the human eye. Methods: Computational fluid dynamics model simulated impingement of the air puff and consisted of 25920 wedge6 elements and employed Spallart-Allmaras model to simulate capture turbulence of the air jet. The time span of the jet wais 30 ms and maximum Reynolds number

Transient flows result in unbalanced forces and high pressure in pipelines. Under these conditions, the combined effects of flow-induced forces along with sudden pipe displacements can create cracks in the pipeline, especially at the junctions. This situation consequently results in water leakage and reduced operational efficiency of the pipeline. In this study, displacements and stresses in a buried pressurized water transmission pipe installed by pipe jacking method are investigated using numerical modeling and considering interactions between fluid, pipe, and soil. The analyses were performed consecutively under no-flow, steady flow, and transient flow conditions, in order to investigate the effects of flow conditions on displacements and stresses in the system. Analyses of the results show that displacements and stresses in the jointed concrete pipes are significant under transient flow conditions. Moreover, because of pressure transient effects, maximum tensile stresses exceed the tensile strength of concrete at the junctions, leading to cracks and consequent water leakage.

Associating the most influential parameters with the product distribution is of uttermost importance in complex catalytic processes such as fluid catalytic cracking (FCC). These correlations can lead to the information-driven catalyst screening, kinetic modeling and reactor design. In this work, a dataset of 104 uncorrelated experiments, with 64 variables, has been obtained in an FCC simulator using 6 types of feedstock (vacuum gasoil, polyethylene pyrolysis waxes, scrap tire pyrolysis oil, dissolved polyethylene and blends of the previous), 36 possible sets of conditions (varying contact time, temperature and catalyst/oil ratio) and 3 industrial catalysts. Principal component analysis (PCA) has been applied over the dataset, showing that the main components are associated with feed composition (27.41% variance); operational conditions (19.09%) and catalyst properties (12.72%). The variables of each component have been correlated with the indexes and yields of the products: conversion, octane number, aromatics, olefins (propylene) or coke, among others.

In this paper, an attempt has been made to analyze the effect of spool port/ groove geometry on the pressure drop and chamber pressures which effect the performance parameters of the flow distributor valve. The work mainly involves formulation of detailed mathematical model of the valve and compare them on the same platform. For mathematical modelling, Matlab has been used. The size of the orifices is considered same throughout the model for better comparison. Initially the construction and functioning of flow distributor valve along with working principles of hydrostatic motor (Rotary Piston) is shown. Next shown the analytical analysis of area change and pressure drops due to different geometry of the spool valve ports. After that the computational fluid dynamics (CFD) analysis has been shown. A complete mathematical model to describe such flow distributor valve is developed after having a comprehensive knowledge of orifice characteristics, flow interactions based on valve geometry. Equations of flow through different orifices (fixed and variable area) of the valve have been developed based on the relationships obtained earlier.

In this paper, we introduce the evolve-then-filter (EF) regularization method for reduced order modeling of convection-dominated stochastic systems. The standard Galerkin projection reduced order model (G-ROM) yield numerical oscillations in a convection-dominated regime. The evolve-then-filter reduced order model (EF-ROM) aims at the numerical stabilization of the standard G-ROM, which uses explicit ROM spatial filter to regularize various terms in the reduced order model (ROM). Our numerical results based on a stochastic Burgers equation with linear multiplicative noise. It shows that the EF-ROM is significantly better results than G-ROM.

Hybrid manufacturing processes that combine additive and machining operations are gaining relevance in modern industry thanks to the capability of building complex parts with minimum material and, many times, with process time reduction. Besides, as the additive and subtractive operations are carried out in the same machine, without moving the part, dead times are reduced and higher accuracies are achieved. However, it is not clear whether the direct material deposition after the machining operation is possible or intermediate cleaning stages are required because of the possible presence of residual cutting fluids. Therefore, different LMD tests are performed on a part impregnated with cutting fluid, both directly and after the removal of the coolant by techniques such as laser vaporizing and air blasting. The present work studies the influence of the cutting fluid in the LMD process and the quality of the resulting part. Resulting porosity is evaluated and it is concluded that if the part surface is not properly clean after the machining operation, deficient clad quality can be obtained in the subsequent laser additive operation.

Based on the two-flavors Polyakov quark-meson model, we study the bubble dynamics of a first-order phase transition in chiral phase diagram at high density but low temperature in the framework of the homogeneous thermal nucleation theory. Under the mean-field approximation, after obtaining the effective potential with inclusion of the fermionic vacuum term, we build a geometric approach to probe two possibly existing minima, which can actually tunnel through a bounce interpolated between a metastable vacuum to an adjacent true vacuum. By separating our discussions into a weak first-order hadron quark phase transition and strong ones, the bubble profiles, the surface tension, the typical radius of the bounce and the saddle point action in the presence of a nucleation bubble as a function of temperature are numerically calculated in detail as the chemical potentials are fixed at $\mu=306 \mathrm{MeV}$ and $\mu=310 \mathrm{MeV}$. our results show that the surface tension remains a small value even when the density is very high and phase boundaries for hadron and quark matter should be resized properly according to the saddle point action evaluated on the bounce. It is also noticed that the inclusion of the deconfinement phase transition in term of the Polyakov loop does not change chiral phase transition dramatically for light quarks.

Ab initio density functional theory molecular dynamics extensive calculations were used for the first time to evaluate stability conditions for relevant phases of InN. In particular, thermal decomposition of InN with formation of N2 molecules and pressure induced wurtzite – rocksalt solid-solid phase transition were established. The results consistent with available experimental data allowed a critical evaluation of potential and limitations of the proposed simulation method. The ab initio molecular dynamics as an efficient tool for simulations of phase transformations of InN including solid-solid structural transition and thermal decomposition with formation of N2 molecules has been demonstrated. It is of high interest because InN being important component of epitaxial quantum structures has still not been obtained as a bulk single crystal making difficult a determination of its basic physical properties and designing new applications.

To overcome the time-consuming drawbacks of Computational Fluid Dynamics (CFD) numerical simulations, this paper proposes a hybrid model based on a parallel architecture based on the concept of intelligent aerodynamics, named PA-TLA (Parallel Architecture combining TCN, LSTM, and Attention mechanism). This model utilizes CFD data to drive efficient predictions of aircraft wake evolution at different initial altitudes during the approach phase. Initially, CFD simulations of continuous initial altitudes during the approach phase are used to generate aircraft wake evolution data, which are then validated against real-world LIDAR data to verify their reliability. The PA-TLA model is designed based on a parallel architecture, combining Long Short-Term Memory networks (LSTM), Temporal Convolutional Networks (TCN), and a tensor concatenation module based on the attention mechanism, which ensures computational efficiency while fully leveraging the advantages of each component in a parallel processing framework. The study results show that the PA-TLA model outperforms both the LSTM and TCN models in predicting the three characteristic parameters of aircraft wake: vorticity, circulation, and Q-criterion. Compared to the serially structured TCN-LSTM, PA-TLA achieves an average reduction in mean squared error (MSE) by 6.80%, mean absolute error (MAE) by 7.70%, and root mean square error (RMSE) by 4.47%, with an average increase in the coefficient of determination (R²) by 0.36%, and a 35% improvement in prediction efficiency. Lastly, this study combines numerical simulation and the PA-TLA deep learning architecture to analyze the characteristics of wake evolution during the near-ground phase, providing theoretical value for further reducing aircraft wake intervals and enhancing airport operational efficiency.

Grating (moiré) interferometry is one of the well-known methods for full-field in-plane displacement and strain measurement. There are many design solutions for grating interferometers, including systems with a microinterferometric waveguide head. This article proposes a modification to the conventional waveguide interferometer head, enabling the implementation of a polarization fringe phase shift for automatic fringe pattern analysis. The article presents both the theoretical consideration of the proposed solution and its experimental verification, along with the concept of the in-plane displacement/strain sensor using the described head.

This study proposes an innovative pharmacovigilance approach, VIGI-4, leveraging ChatGPT Teams Pro version. Our method involves aggregating data from all phase 4 studies published in February 2024 to identify adverse reactions. These results are categorized by disease state alphabetically, demonstrating the method's capacity to generate structured and easily navigable outputs. The results section is tailored to exemplify the valuable, actionable insights attainable through our workflow. This research emphasizes the game-changing potential of integrating advanced technologies such as ChatGPT into pharmacovigilance, signaling a new era in safeguarding drug safety.

Permafrost covers about 23% ~ 25% of the land in the northern hemisphere, mainly in Russia, Canada, Alaska, Northeast and Qinghai Tibet Plateau (QTP) in China. Many engineering especially the transportation has been in the permafrost regions above. Under the action of highways construction and global warming, permafrost under infrastructures is degraded and causes serious damage. Two phases closed thermosyphon (TPCT) is a widely accepted green countermeasure against the problem in permafrost regions. Although it has been applied to prevent permafrost degradation, their application presents significant challenges on account of the stronger endothermic action of asphalt pavement. This paper focused on the thermosyphon technology and application in the permafrost. Moreover, the article highlighted the excellent working performance of the TPCT that improving the stability of the infrastructures and prevent it degrading due its excellent efficiency of heat transfer. The industrial applications of the TPCT were also summarized, along with their limitations. Finally, the results reported in this paper can provide a valuable guidance for the design of the TPCT and construction of the permafrost regions in the future.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Digital-Radio-Frequency-Memory (DRFM) has emerged as an advanced technique to achieve diverse jamming signals, due to its capability of intercepting waveforms within a short time. Multiple-Input Multiple-Output (MIMO) radars can transmit agile orthogonal waveform sets for different pulses to combat the DRFM-based jamming, where any two groups of waveform sets are also orthogonal. In order to design multiple groups of orthogonal waveform sets at the same time, this article formulates a group orthogonal waveforms optimal design model, whose objec-tive function is the weighted sum of the intra- and inter-group orthogonal performances metrics. To solve this optimization problem, this article proposes a group orthogonal waveforms design algorithm. Based on a primal-dual type method and proper relaxations, the proposed algorithm transforms the original problem into a series of simple sub-problems. Numerical results demonstrate that the proposed algorithm has the ability to balance the intra- and inter-group orthogonal performances by adjusting the weighting factors, which is not available using other state-of-the-art orthogonal waveform design algorithms.

Femtoscopy is a unique tool to investigate the space-time geometry of the matter created in ultra-relativistic collisions. If the probability density distribution of hadron emission is parametrized, then the dependence of its parameters on particle momentum, collision energy, and collision geometry can be given. In recent years, several measurements came to light that indicated the adequacy of assuming a Lévy-stable shape for the mentioned distribution. In parallel, several new phenomenological developments appeared, aiding the interpretation of the experimental results, or providing tools for the measurements. In this paper we review and discuss some of these advances, phenomenological and experimental.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

The extraction method for simultaneously analyzing fatty acids (Myristic acid, cis-Palmitvaccenic acid, Palmitic acid, Palmitic-9,9-d2 acid, Oleic acid, Stearic acid and Stearic-2,2-d2 acid) related to biodiesel fuel in large algae was developed. The introduction of trimethylaminoethyl (TMAE) derivatives into the hydroxyl group (-OH) functional group of the analyte was able to improve ionization and obtain high sensitivity. Liquid Chromatography (LC) was used to investigate the optimal mobile phase composition and flow rate for the separation of five derived fatty acids. In this study, a solid phase extraction (SPE) column was introduced for efficient extraction of fatty acids, and the optimal conditions for SPE were set by comparing the recovery rate according to the solvent for each step (loading, washing, and elution) of SPE from macroalgae.

The research community has shown significant interest in the aqueous synthesis of nanomaterials due to its ability to eliminate the need for complex organic solvents. This synthesis approach aligns with the principles of green chemistry, attracting considerable attention. Aqueous solution technology in fabricating nanostructures has gained recognition for its potential to create ultrasensitive, low-energy, and ultrafast optoelectronic devices. This report focuses on synthesizing lead iodide (PbI2) nanoplates using a water-based solution technique and fabricating a planar photodetector. The photodetectors with a planar type of device structure (ITO/PbI2 NPs/Au) demonstrated a remarkable photosensitivity of 3.9×103 and a photoresponsivity of 0.51 mA/W at a wavelength of 405 nm. Notably, the asymmetrical output properties of ITO/PbI2 NPs/Au detector deliver additional evidence of the effective creation of a Schottky contact. Thus, the photodetector exhibited a photoresponse even at 0 V bias, leading to the realization of self-powered photodetectors. Additionally, the device exhibited a rapid photoresponse of 0.21/0.38 s (−5 V) in the visible range. This study has expanded the horizons for the aqueous-phase synthesis of nanoplate nanostructures, enabling the large-area fabrication of high-performance photodetectors.

The mechanism of vapor-gas deposition of vinyltrimethoxysilane (VS) and ethylene glycol (EG) from azeotropic solutions is investigated, which allows to reduce the evaporation temperature of the components of working mixtures. The need for such studies is associated with the development of a new direction in the technology of vapor-gas deposition of polymer coatings. Methods have been developed for monitoring the chemical composition of working solutions in evaporators using optical spectroscopy, which allow calculating the partial pressures of vapor phase components. Based on these studies, compositions of working solutions are proposed that allow to equalize the partial pressures of the components of working mixtures with a large difference in boiling point. A new method of vapor-gas deposition of non-volatile powder inhibitors on metals is proposed. Chemical compositions of siloxane coatings were determined using XPS and mechanisms of interaction of VS with polymerization promoters ethylene glycol and 1-hydroxy ethylidene-1,1-diphosphonic acid (HEDP) were proposed.

Scientific advancements in the food industry have resulted in the discovery of natural substances that can serve various functions in food. Essential oils, in particular, can act as food preservatives or flavoring agents due to their abundance of natural antioxidants, which possess preservative properties. In this study, the composition of Thymus vulgaris essential oil was determined using GC-MS and HS-SPME. The essential oil obtained from Thymus vulgaris L. through hydro-distillation yielded approximately 4%. GC/MS analysis of the essential oil identified 11 components, with a predominant presence of oxygenated monoterpenes (56.97%). Notably, carvacrol (37.63%) and thymol (17.35%) were present in significant amounts, accounting for 54.98% of the overall composition. The in vitro antioxidant activity of the essential oil was evaluated using three methods. The DPPH free radical scavenging test yielded an IC50 of 0.51±0.11 mg mL-1. The β-carotene/linoleic acid bleaching test resulted in an IC50 of 2.58±0.10 mg mL-1. Finally, the ABTS assay indicated relatively lower antioxidant activity compared to ascorbic acid.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

In this paper, Fe-Cr-C-N-Al-Y wear-resistant surfacing alloy was prepared by open arc surfacing with self-shielded flux-cored wire. The wear properties of the surfacing alloy were analyzed by MLS-23 rubber wheel wet sand wear tester. The phase composition and microstructure of the surfacing alloy were analyzed by XRD, SEM, EBSD and TEM, and the strengthening mechanism and wear mechanism of the alloy were discussed. The results show that the microstructure of Fe-Cr-C-N-Al-Y surfacing alloy is composed of M + γ-Fe + M7C3 + AlN. When the content of nano-Y2O3 is 0.456wt. %, the formability of the surfacing alloy is the best and the wetting angle is the smallest, which is 50.8°, AlN and M7C3 precipitate the most, and the microstructure grain is the smallest. At this time, the hardness value of the surfacing alloy is up to 62.3 HRC, which is 11.8 % higher than that of the unmodified surfacing alloy. The minimum wear weight loss is 0.125 g, and the wear resistance is increased by 41.86 %. The wear mechanism of surfacing alloy is mainly plastic deformation mechanism, and the material removal process is micro cutting and furrow wear.

Applying of blood biopolymers to regulate the phase composition is promising in designing the hydroxyapatite-based hybrid biomaterials with controllable resorbability. Hybrid materials based on hydroxyapatite and platelet-poor plasma (PPP) were formed in conditions of chemical precipi-tation at pH 11, [Ca2+] / [PO43–] ratio 1.67, PPP volume fraction of 6–24%, maturing time of 4–9 days. Mineral component of the materials was represented as 53% hydroxyapatite / 47% amor-phous calcium phosphate after 4 days of maturation, and 100% hydroxyapatite after 9 days of maturation. Varying PPP content from 6% to 24% provided forming of materials with rather de-fined content of amorphous calcium phosphate and biopolymer component, having desired mor-phology ranging from typical apatitic conglomerates to hybrid apatite-biopolymer fibers. Co-precipitated hybrid materials based on hydroxyapatite and PPP are promising for bone regen-eration in osteoplastic and maxillofacial applications.

Magnetic nanoparticles (MNPs) have attracted a great interest in nanomedical research. MNPs exhibit many important properties, particularly, magnetic hyperthermia for selective killing of cancer cells is one of them. In hyperthermia treatment, MNPs act as nano-heaters when they are under the influence of an alternating magnetic field (AMF). In this work, micromagnetic simulations have been used to investigate the magnetization dynamics of a single-domain nanoparticle of magnetite in an external AMF. Special attention is paid to the circumstances dealing with a dynamic phase transition (DPT). Besides, we focus on the influence of the orientation of the magnetic easy-axis of the MNP on the dynamic magnetic properties. For amplitudes of the external AMF above certain critical value, the system is not able to follow the magnetic field and it is found in a dynamically ordered phase; whereas for larger amplitudes, the state corresponds to a dynamically disordered phase and the magnetization follows the external AMF. Our results suggest that the way how the order-disorder DPT takes place, and both the metastable lifetime as well as the specific loss power (SLP), are strongly dependent on the interplay between the orientation of the magnetic easy-axis and the amplitude of the external AMF.

The analogy between the theory of phase transitions in simple fluids and vehicular traffic flow has long been suspected, promising a new level of understanding of urban congestion by standing on one of the firmer foundations in physics. The obstacle has been the interpretation of the thermal energy of the gas-particle system, which remains unknown. This paper proposes the flow of cars through the network as a viable interpretation, where the fundamental diagram for traffic flow would be analogous to the coexistence curve in gas-liquid phase transitions. Thanks to the power-law form of the coexistence curve, it was possible to formalize that the resulting network traffic model belongs to the Kardar-Parisi-Zhang universality class. The scaling relationships arising in this universality class are found to be consistent with West's scaling theory for cities. It is shown that congestion costs (delays + fuel consumption) scale superlinearly with city population, possibly and worryingly more so than predicted by West's theory. Implications for sustainability and resiliency are discussed.

This paper proposes how to reduce the consumption of active electrical energy (kwh) by 90.3% while maintaining the same mechanical work speed (RPM) at variable torque loads (fans or air-fluid blowers, centrifugal pumps are not included). of water and similar fluids), by using the “Fan Law” in an innovative way in PMSM-type synchronous motors (a comparative study never before carried out on the Fan Law). The work is carried out comparatively between brushless a-synchronous motors with starting loop (or motor with a short-circuited loop) versus brushed a-synchronous motors and PMSM-type synchronous motors without the need to use VDF (variable frequency drives), simplifying technology (electronics) and saving costs in an innovative way (R+D+i). The case study was developed on a design applied to a centrifugal air extractor/blower with PMSM/IPM type synchronous motor. Applying one of the fan affinity laws –with the impeller diameter 10.5 (mm) constant- the electrical power absorbed by the blower motor is proportional to the cube of the shaft speed: . Being “P” power (Watts) and “N” speed (RPM). Carrying out a comparative study between power (watts), active energy consumption (kwh) and rotational speed (RPM). This has a direct impact on the costs of residential and commercial single-phase active electrical energy consumption, measured in kilowatt-hours (kwh). Carrying out a comparative study between three (3) types of alternating current (AC) electrical machines, according to the NEMA (National Electrical Manufacturers Association); AC motors fall into three (3) categories. One (1), synchronous motors (Syncrhonous Motor) of three types: (1a) excitation by DC (DC Excited Motor), (1b) permanent magnet (Permanent Magnet Motor) and (1c) reluctance motor (Reluctance Motor) or motor Step by Step. Two (2), asynchronous induction motors of two types: (2a) Squirrel-Cage Induction Motor and (2b) Wound-Rotor Induction Motor. Three (3) series-wound motor (Series-Wound Motor) also called universal motor (they have carbons).

Fiber distributed optical fiber acoustic sensor (DAS) is generally used in distributed long-distance acoustic/vibration measurement. We found that DAS with excellent performance of low self-noise and anti-fading in combination with the plastic structure in daily life as an acoustic transducer can achieve high-sensitivity acoustic measurement at a single point rather than designing a state-of-the-art acoustic transducer or using special enhanced scattering fiber. The simple acoustic transducer we proposed for DAS can reach the sensitivity level of -106.5dB re. 1rad/μPa at a sensing range of 5.1 km, which can meet many demands on the industrial site.

From the formalism of the thermodynamics of irreversible processes and the theory of complex systems, characterization of longevity and aging and its relationship with the emergence and evolution of cancer was carried out. It was found that: 1. The rate of entropy production can be used as an index of robustness, plasticity, the aggressiveness of cancer, and as a measure of biological age; 2. The aging process, as well as the evolution of cancer, goes through what we have called “biological phase transition”; 3. The process of metastasis, which occurs through epithelial-mesenchymal transition (EMT), appears as a phase transition far from thermodynamic equilibrium and exhibits Shilnikov chaos-like dynamic behavior. This dynamic guarantees the robustness of the process and, in turn, its unpredictability; 4. It was shown that as the ferroptosis process is strengthened, the complexity of the dynamics associated with the emergence and evolution of cancer decreases. The theoretical framework developed contributes to a better understanding of the biophysical-chemical phenomena of longevity and aging and their relationship with cancer.

We experimentally demonstrate enhanced spectral broadening of femtosecond optical pulses after propagation through silicon-on-insulator (SOI) nanowire waveguides integrated with two-dimensional (2D) graphene oxide (GO) films. Owing to the strong mode overlap between the SOI nanowires and the GO films with a high Kerr nonlinearity, the self-phase modulation (SPM) process in the hybrid waveguides is significantly enhanced, resulting in greatly improved spectral broadening of the femtosecond optical pulses. A solution-based, transfer-free coating method is used to integrate GO films onto the SOI nanowires with precise control of the film thickness. Detailed SPM measurements using femtosecond optical pulses are carried out, achieving a broadening factor of up to ~4.3 for a device with 0.4-mm-long, 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of ~3.5 and the effective nonlinear figure of merit (FOM) by a factor of ~3.8, relative to the uncoated waveguide. Finally, we discuss the influence of GO film length on the spectral broadening and compare the nonlinear optical performance of different integrated waveguides coated with GO films. These results confirm the improved nonlinear optical performance for silicon devices integrated with 2D GO films.

In the context of all-digital radar systems, phase-modulated continuous wave (PMCW) based on pseudorandom binary sequences (PRBSs) appears a prominent candidate modulation scheme for applications such as autonomous driving. Among the reasons for that are its simplified transmitter architecture and lower linearity requirements, e.g., compared to orthogonal-frequency division multiplexing radars, as well as its high velocity unambiguity and multiple-input multiple-output operation capability that are characteristic of digital radars. For appropriate operation of a PMCW radar, choosing a PRBS whose periodic autocorrelation function (PACF) has low sidelobes and high robustness to Doppler shifts is paramount. In this sense, this article performs an analysis of Doppler shift tolerance of the PACFs of typically adopted PRBSs in PMCW radar systems supported by simulation and measurement results. To accurately measure the Doppler-shift-induced degradation of PACFs, peak power loss ratio (PPLR), peak sidelobe level ratio (PSLR), and integrated-sidelobe level ratio (ISLR) were used as metrics. Furthermore, to account for effects on targets whose ranges are not multiples of the range resolution, oversampled PACFs are analyzed.

A theoretical description of quantum jumps at the level of elementary particles is proposed, based on a micro-cosmological interpretation of their de Broglie phase. The third quantization formalism proposed in current literature for the description of baby universes in quantum cosmology is used here to describe the breakdown of unitarity in the transition from the pre-jump to the post-jump wave function. The corpuscular aspect manifested by the particle in the micro-interaction that originates the jump is represented by a pair of evanescent "micro-universes", respectively pre- and post-jump, connected by a wormhole. The latter represents the actual implementation of the interaction that leads to the projection on the outgoing state; this interaction is always local, even when the selected outgoing state is entangled. Therefore, the decoherence which leads to the emergence of classicality is originated by the same fundamental interactions of the Standard Model involved in the unitary evolution of the wave function. The objective nature of the reduction process admits implications on the possibility of using the formalism in the cosmological context, which are briefly discussed.

Although lithium-ion batteries have extensively been used in various applications because of their high energy capacity, fracture and failure, the by-products of large strains and stresses caused by fast charging and discharging need yet to be addressed. The size effects on the mechanical behavior of the nano-sized structures are significant; however, the classical elasticity theory may not consider such effects. On the other hand, surface stress theory, as a robust and potential theory, is suitable in considering size effects in nano-scale structures. Therefore, in this paper, in order to involve the surface stress effects on the fracture behavior of Li-ion batteries, the following steps are taken. Firstly, a phase-field model is used to determine the evolution of the concentration profile. Subsequently, the stress distribution is obtained by using the surface stress theory combined with chemical equations for a planar electrode. Afterward, by using the weight function method for an edge crack in the plate, the stress intensity factor is derived for all time steps and possible crack lengths during the process. It is found that with increasing phase boundary thickness parameter or decreasing phase-separation phenomenon, the surface mechanics parameters become more influential. Furthermore, in the presence of positive surface stress, the diffusion-induced stress distribution decreases, which in turn reduces the stress intensity factor. In addition, in this paper, the two states of surface stress are compared either for elastic or total strain. Concerning stresses and concentrations, the results indicate a big difference at the beginning of the deintercalation process showing, in particular, 2% for stresses, but the differences diminish gradually.

The influence of the hot isostatic pressing (HIP) post-processing step on structural and phase changes, porosity healing and mechanical strength in a powder metallurgy Ti35Nb2Sn alloy was studied. Powders were pressed at room temperature at 750 MPa, and then sintered at 1,350°C in a vacuum for 3 h. The standard HIP process at 1,200°C and 150 MPa for 3 h was performed to study its effect on a Ti35Nb2Sn powder metallurgy alloy. The influence of the HIP process and cold rate on density, microstructure, the quantity of interstitial elements, mechanical strength and Young's modulus was investigated. HIP post-processing for 2 h at 1,200°C and 150 MPa led to greater porosity reduction and a marked retention of the β phase at room temperature. The slow cooling rate during the HIP process affected phase stability, with a large amount of α”-phase precipitate, which decreased the titanium alloy’s yield strength.

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

Organic-organic interactions play important roles in the secondary organic aerosol formation, but the interactions are complex and poorly understood. Here we use environmental molecular beam experiments combined with molecular dynamics simulations to investigate the interactions between methanol and nopinone, as atmospheric organic proxies. In the experiments, methanol monomers and clusters are sent to collide with three types of surfaces, i.e., graphite, thin nopinone coating on graphite and multilayer surfaces, at temperatures between 140 K and 230 K. Methanol monomers are efficiently scattered from the graphite surface, whereas the scattering is substantially suppressed from nopinone surfaces. The desorption from the three surfaces is similar, suggesting that all the surfaces have weak or similar influences on the methanol desorption. The molecular dynamics results show that upon collisions the methanol clusters shatter, and the shattered fragments quickly diffuse and recombine to clusters. The desorption involves a series of processes, including detaching from clusters and desorbing as monomers. The experimental results also show that all trapped methanol molecules completely desorb within a short experimental time scale at temperatures of 180 K and above. At lower temperatures, the desorption rate decreases, and a long experimental time scale is used to resolve the desorption, where three desorption components are identified. The fast component is beyond the experimental detection limit. The intermediate component exhibits multi-step desorption character and has an activation energy of E_a = 0.18 ± 0.03 eV, in good agreement with simulation results. The slow desorption component is related to diffusion processes due to the weak temperature dependence.

A novel polyphenol‑coated CoFe₂O₄ system was synthesized as a magnetic adsorbent by chemical oxidative polymerization process for magnetic solid-phase extraction of lawsone. The synthesized nanoadsorbent showed a spherical morphology with diameters under 50 nm by scanning electron microscopy images. The extraction efficiency of this adsorbent was studied towards the extraction of lawsone from saline aqueous solution in dispersion mode. Major parameters including the type and volume of desorption solvent, amount of sorbent, desorption time, extraction time, extraction temperature, ionic strength and pH were optimized. Under the optimum conditions the relative standard deviation in 0.005 µg mL^-1 (inter-day n = 6; intra-day: n = 6; and adsorbent to adsorbent n = 4) were obtained as 5.2, 8.07 and 11.7%, respectively. A linear calibration curve in the range of 0.003–0.5 µg mL^-1 with R² = 0.993 was obtained. The limit of detection and limit of quantification of the method were 0.001 µg mL^-1 and 0.003 µg mL^-1, respectively. The relative recovery percentages were in range of 90-96.4% for henna leaves, henna shampoo, and henna dermal lotion real samples.

The growth of solid particles during liquid phase sintering was modeled by the Cellular Automata method. The binary phase diagram and Fickian approach for the diffusion process were applied to simulate the chemical composition variation in liquid and solid phases during sintering. The Oswald-Ripening effect was considered during the dissolution of the solid phase in the liquid phase. It is used to define the probability of solid-phase dissolution by the liquid phase and develop the model to simulate the alloy with solid solubility. So, the microstructure could be modeled in the liquid phase sintering process.

This paper reports on the fabrication of alumina doped preforms using MCVD-vapor phase chelate delivery system with Al(acac)3 as the precursor. The objectives of the work are to study the deposition process, the efficiency of the fabrication process, and the quality of the fabricated fiber preforms. Two parameters are studied, Al(acac)3 sublimator temperature (TAl°C) and deposition direction (i.e. downstream and upstream). Other parameters such as oxygen flow and deposition temperature are fixed. The results showed that a high uniformity of refractive index difference (%RSD < 2%) and core size (%RSD < 2.4%) was obtained along the preform length using downstream deposition while for the combined upstream and downstream deposition the uniformity was deteriorated. The process efficiency was found to be about 21% for TAl°C of 185°C and downstream deposition. From the EDX elemental analysis, the refractive index was found to increase by 0.0025 per mole percent of alumina.

Knowledge about the formation energies of compounds is essential to derive phase diagrams of multi-component phases with respect to elemental reservoirs. The determination of formation energies using common (semi-)local exchange-correlation approximations of density functional theory (DFT) exhibits well-known systematic errors if applied to oxide compounds containing transition metal elements. In this work, we generalize, reevaluate and discuss a set of approaches proposed and widely applied in the literature to correct for errors arising from the over-binding of the O2 molecule and from correlation effects of electrons in localized transition-metal orbitals. The DFT+U method is exemplarily applied to iron oxide compounds, and a procedure is presented to obtain U values, which lead to formation energies and electronic band gaps comparable to experimental values. Using such corrected formation energies, we derive the phase diagrams for LaFeO3, Li5FeO4 and NaFeO2, which are promising materials for energy conversion and storage devices. A scheme is presented to transform the variables of the phase diagrams from the chemical potentials of elemental phases to those of precursor compounds of a solid-state reaction, which represents the experimental synthesis process more appropriately. The discussed workflow of methods can directly be applied to other transition metal oxides.

How does the human neurophysiological system self-organize to achieve optimal phase relationships among joints and limbs, such as in the composite rhythms of butterfly and front crawl swimming, drumming, or dancing? We conducted a systematic review of literature relating to CNS control of phase among joint/limbs in continuous rhythmic activities. SCOPUS and Web of Science were searched using keywords ‘Phase AND Rhythm AND Coordination’. This yielded 998 matches from which 23 papers were extracted for inclusion based on screening criteria. The empirical evidence arising from in-vivo, fictive, in-vitro, and modelling of neural control in humans, other species, and robots indicates that the control of movement is facilitated and simplified by innervating muscle synergies by way of spinal central pattern generators (CPGs). These typically behave like oscillators enabling stable repetition across cycles of movements. This approach provides a foundation to guide the design of empirical research in human swimming and other limb independent activities. For example, future research could be conducted to explore whether the two-layer CPG model proposed by Saltiel et al [1] to explain locomotion in cats might also explain the complex relationships among the cyclical motions in human swimming.

We investigate a notable class of states peculiar to a bosonic binary mixture featuring repulsive intraspecies and attractive interspecies couplings. We evidence that, for small values of the hopping amplitudes, one can access particular regimes marked by the fact that the interwell boson transfer occurs in a jerky fashion. This property is shown to be responsible for the emergence of a staircase-like structure in the phase diagram and to strongly resemble the mechanism of the superfluid-Mott insulator transition. Under certain conditions, in fact, we show that it is possible to interpret the interspecies attraction as an effective chemical potential and the supermixed soliton as an effective particle reservoir. Our investigation is developed both within a fully quantum approach based on the analysis of several quantum indicators and by means of a simple analytical approximation scheme capable of capturing the essential features of this ultraquantum effect.

The goal of this paper is to propose a dual version of the direct cosine simplex algorithm (DDCA) for general linear problems. Unlike the two-phase and the big-M methods, our technique does not involve artificial variables. Our technique solves the dual Klee-Minty problem in two iterations and solves the dual Clausen’s problem in four iterations. The utility of the proposed method is evident from the extensive computational results on test problems adapted from NETLIB. Preliminary results indicate that this dual direct cosine simplex algorithm (DDCA) reduces the number of iterations of two-phase method.

This paper presents the design of a high frequency zero voltage switching (ZVS) full-bridge converter with a phase-shifted driving signal for photovoltaic applications. The resonant power converter can provide high-power capacity under high-frequency operation. The proposed power converter can also reduce the size of the transformer under the same power rating. The high-frequency transformer was developed by using the resonant and switching frequencies of the power converter to reduce the switching loss and to improve the system efficiency. Phase-shifted modulation was selected to drive the switches of a full-bridge power converter based on the switching loss minimization method. The desired output voltage was controlled using a closed-loop controller under a loop gain stability margin. The simulation results showed that the output voltage can be controlled to the desired constant when the input voltage changes from 30 VDC to 60 VDC. The desired output voltage of power converter is constant at 400 VDC. The power converter can transfer the DC supply to a 220 VAC household via grid-connected inverter. Therefore, the proposed study showed the effectiveness of the phase-shift ZVS full-bridge power converter with high-frequency transformer. This power converter can control the operation of the desired voltage system and has a small sizing of power converter system, low switching loss, and high system efficiency.

We report on comparison between temperature-dependent magneto¬absorption and magnetotransport spectroscopy of HgTe/CdHgTe quantum wells in terms of detection of phase transition between topological insulator and band insulator states. Our results demonstrate that temperature-dependent magnetospectroscopy is a powerful tool to discriminate trivial and topological insulator phases, yet magnetotransport method is shown to have advantages for clear manifestation of the phase transition with accurate quantitative values of transition parameter (i.e. critical magnetic field Bc).

Fabric phase sorptive extraction, an innovative integration of solid phase extraction and solid phase microextraction principles, has been combined with gas chromatography-mass spectrometry for the rapid extraction and determination of nineteen organochlorine pesticides in various fruit juices and water samples. FPSE consolidates the advanced features of sol-gel derived extraction sorbents with the rich surface chemistry of cellulose fabric substrate, which could directly extract target analytes from complex sample matrices and substantially simplifies the sample preparation operation. Important FPSE parameters including sorbent chemistry, extraction time, stirring speed, type and volume of back-extraction solvent and back-extraction time have been optimized. Calibration curves were obtained in the concentration range 0.1-500 ng/mL. Under the optimum conditions, the limits of detection were obtained in the range 0.007-0.032 ng/mL with satisfactory precision (RSD<6%). The relative recoveries obtained by spiking organochlorine pesticides in water and selected juice samples were in the range of 91.56–99.83%. The sorbent sol-gel poly(ethylene glycol)-poly(propylene glycol)-poly(ethylene glycol) was applied for the extraction and preconcentration of organochlorine pesticides in aqueous and fruit juice samples prior to analysis with gas chromatography-mass spectrometry. The results demonstrated that the present method is simple, rapid, and precise for the determination of organochlorine pesticides in aqueous samples.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

Bamboo plastic composites have become a hot research topic and a key focus of research. However, the many strong, polar, hydrophilic hydroxyl groups in bamboo flour (BF) results in poor interfacial compatibility between BF and hydrophobic polymers. Maleic anhydride-esterified (MAH-e-BF) and lactic acid-esterified bamboo flour (LA-e-BF) were prepared using an in situ solid-phase esterification method with BF as the raw material and maleic anhydride or lactic acid as the esterifying agent. Fourier transform infrared spectroscopy results confirmed that BF esterification with maleic anhydride and lactic acid was successful, with the esterification degrees of MAH-e-BF and LA-e-BF at 21.04 and 14.36%%, respectively. Esterified BF was characterized by scanning electron microscopy, contact angle testing, X-ray diffractometry, and thermogravimetric analysis. The results demonstrated that esterified BF surfaces were covered with graft polymer and the surface roughness and bonding degree of MAH-e-BF clearly larger than those of LA-e-BF. The hydrophobicity of esterified BF was significantly higher than BF and the hydrophobicity of MAH-e-BF better than LA-e-BF. The crystalline structure of esterified BF showed some damage, with MAH-e-BF exhibiting a greater decrease in crystallinity than LA-e-BF. Overall, the esterification reaction improved BF thermoplasticity, with the thermoplasticity of MAH-e-BF appearing better than LA-e-BF.

The stability of twenty seven composts and organic substrates (including raw, less stable and stable materials) was assessed using two different liquid phase tests were carried out. One of the tests was introduced in 1998 and was based on the calculation of a Specific Oxygen Uptake Rate (SOUR). The newly introduced liquid phase test presented here is simpler to set-up and to perform that the older liquid phase test. It is based on the quantification of oxygen consumption in the headspace of a BOD bottle that contains the liquid-solid solution. The results indicate that a marginal correlation does exist between the main indices calculated from both tests. The correlation was stronger for the indices calculated for stable-processed organics than for the raw (unprocessed materials). The SOUR ranged from 1520 to 3650mg O₂/kg VS-h for the raw materials and from 110 to 1150 mg O₂/kg VS-h for the processed materials, respectively. The corresponding stability rate related index (LSRI₂₄) of the new liquid phase test introduced here ranged from 240 to 1180 mg O₂/dry kg-h for the raw materials and from 64 to 792 mg O₂/dry kg-h for the processed ones.

This work intends to present a study on relations between a Lie algebra called dispersion operators algebra, linear canonical transformation and a phase space representation of quantum mechanics that we have introduced and studied in previous works. The paper begins with a brief recall of our previous works followed by the description of the dispersion operators algebra which is performed in the framework of the phase space representation. Then, linear canonical transformations are introduced and linked with this algebra. A multidimensional generalization of the obtained results is given.

This paper addresses the mixed convective flow and heat transfer in combustible third grade fluid through a slant channel that is filled with a permeable materials. The fluid layer in contact with the lower plate is exposed to convective heating with the ambient while at the upper plate, a constant heat flux is experienced. We employ the spectral quasilinearisation method (SQLM) to the coupled nonlinear flow governing equations. Fluid velocity and temperature profiles, local entropy generation and irreversibility ratio are computed and analysed quantitatively and qualitatively. A residual error analysis demonstrated high accuracy and convergence of the numerical method. The results on flow and thermal effects, entropy generation rate and Bejan number revealed fascinating manifestations that have profound implications in design of thermo-mechanical systems. In particular, the results of the thermal analysis are pertinent to optimal designs of systems that achieve efficient energy utilization.

EV transmissions operate at high speeds, upto 30,000 rpm. High speed operation puts higher demands on bearings, seals, and gears. Bearings in EV transmissions are prone to electrically induced bearing damage and may exhibit signs of pitting and fluting. Surface-initiated rolling contact fatigue is another common problem gaining increased attention lately. Most EV transmissions require a coupling between an oil-lubricated gearbox to an electrical motor that runs with minimal lubrication at very high rpm. High mechanical and thermal stresses the seals are exposed to under starved lubrication conditions have a detrimental impact on their service life. Hence, proper lubrication is critical. In general, EV transmission fluids call for a somewhat different spectrum of properties compared to conventional ATF. Gear tribology simulations open new ways to the design and optimization of lubrication for EV transmissions. Additionally, such simulations can also provide valuable insights into the effects of different oil properties on cooling and lubrication efficiencies, thereby helping in matching the lubricant and hardware characteristics for optimal performance. In the present communication, we demonstrate the effects of different lubricants and surface finishing technologies on the tribology of high-speed gears using tribological tests and advanced thermal elastohydrodynamic (TEHD) simulations. Important roles of lubricity additives and surface finish optimization are highlighted in conjunction with a move towards ultralow viscosity EV transmission fluids.

The recent green manufacturing demands have boosted the development of new biodegradable lubricants to replace petroleum-based lubricants. In this regard, water-based lubricants have been at the forefront of recent research for a wide range of industrial applications, including metalworking fluids (MWFs). In this work, we present an experimental investigation on the performance of novel green MWFs based on aqueous nopal mucilage solutions. For this, fully biodegradable solutions with different mucilage concentrations were evaluated in terms of rheological, tribological, thermal stability and turning (minimum quantity lubrication) performance, and compared to a commercial semisynthetic oil-based MWF (Cimstar 60). Mucilage solutions exhibited viscoelastic shear-thinning behavior, which was enhanced along with mucilage concentration. The solution with the highest mucilage content studied resulted in the lowest wear, friction and temperature in comparison to the other solutions and neat water in extreme pressure four-ball tests, and a similar level of lubricity as compared to the commercial MWF in cutting tests. This performance is associated to the enhanced viscosity and elasticity of the solution, as well as to the contents of lipids with fatty acids in the mucilage. Overall, the present results reveal the relevance of the viscoelastic behavior of the lubricant, elasticity in particular, in lubrication processes, and points to nopal mucilage as an effective green additive to produce innocuous MWFs.

Efficient implementation of clean energy technologies, including pioneering solutions like mobile solar PV systems mounted on trailers (MSPT), is pivotal for addressing energy challenges, especially in regions with constrained power grid access. This endeavour is vital for meeting escalating elec-tricity demands and aligning with the UN Sustainable Development Goal (SDG) aimed at ensuring dependable and sustainable energy provision in developing countries. This paper investigates the aerodynamic behaviour of a designed MSPT using numerical and experimental approaches. Spe-cifically, the study focuses on the effects of wind velocity and tilt angels on the drag and lift forces, as well as drag and lift coefficients on the panel used in the MSPT system. Additionally, the overall wind force acting on the entire MSPT (including 9 large solar PV panels) was examined, considering the combined effects of wind flow and the system's geometry. The simulations were conducted using ANSYS-Fluent software and experimental testing was performed utilizing scaled-down models to validate the accuracy of the simulation. The insights and the knowledge from this study can be utilized to optimize the design, installation, and operation of such systems, ultimately enhancing their performance, reliability, and paving ways for further improvements in mobile solar PV technology.

We will apply Pascal’s hydrostatic pressure law to black holes and also to the Hubble sphere. Haug has recently demonstrated how hydrostatic pressure in water can be utilized to determine the Planck length. One can conceptualize the energy in the Hubble sphere as a type of superfluid, and if this is correct, then Blaise Pascal’s hydrostatic pressure formula may also be applicable to such a superfluid, even within the Hubble sphere. By employing the same method on the Hubble sphere and considering it as a Schwarzschild black hole with the critical Friedmann mass, we can estimate the Planck length based on its hypothetical hydrostatic pressure.

The Physics-Informed Neural Networks (PINNs) improve the efficiency of data utilization by combining physical principles with neural network algorithms and ensure that the predictions are consistent and stable with the physical laws. PINNs opens up a new approach to address inverse problems in fluid mechanics. Based on the single-relaxation-time lattice Boltzmann method (SRT-LBM) with the Bhatnagar-Gross-Krook (BGK) collision operator, the PINN-SRT-LBM model is proposed in this paper for solving the inverse problem in fluid mechanics. The PINN-SRT-LBM model consists of three components. The first component involves a deep neural network that predicts the equilibrium control equations in different discrete velocity directions within SRT-LBM. The second component employs another deep neural network to predict non-equilibrium control equations, enabling inference of the fluid's non-equilibrium characteristics. The third component, a physics informed function translates the outputs of the first two networks into physical infor-mation. By minimizing the residuals of the physical partial differential equations (PDEs), the physics informed function infers relevant macroscopic quantities of the flow. The model evolves two sub-models applicable to different dimensions, named PINN-SRT-LBM-I and PINN-SRT-LBM-II models according to the construction of the physical informed function. The innovation of this work is the introduction of SRT-LBM and discrete velocity models as physical drivers into the neural network through the interpretation function. Therefore, PINN-SRT-LBM allows the neural network to handle inverse problems of various dimensions and focus on problem-specific solving. Experimental results confirm the accurate prediction of flow infor-mation at different Reynolds numbers within the computational domain. Relying on the PINN-SRT-LBM models, inverse problems in fluid mechanics can be solved efficiently.

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.

Geothermal energy aims at harnessing the heat of the Earth to produce energy, from the near-surface to great depths. Emphasis is put on geothermal reservoirs in crystalline rocks, hence vol-canic islands and crystalline basements of sedimentary basins based on three examples world-wide. Hot brines circulate in those rocks and are responsible for their hydrothermal alteration because of fluid-rock interactions. This includes dissolution of preexisting minerals and crystal-lization of newly formed ones which provide many information of crucial importance for a better exploration of those reservoirs. For example, the crystallization of clay minerals results from the dissolution of preexisting minerals (feldspar and ferro-magnesian minerals in plutonic, volcanic or metamorphic rocks) or from the direct precipitation from geothermal brines, in specific condi-tions. Clay minerals are found in both the geothermal reservoirs and in the clay-cap found above them. Other newly formed minerals such as quartz, carbonates or sulfates have also recorded the conditions of temperature and salinity encountered by fossil reservoirs which can be evaluated thanks to the study of fluid inclusions trapped during their crystallization. This paper presents results from several geothermal deep sites and surface analogues to pinpoint the role played by newly-formed minerals in the characterization of geothermal reservoirs and their cap-rock.

Maxwell equations governing electromagnetic effects are being shown to be equivalent to the compressible inviscid Navier-Stokes equations applicable in fluid dynamics and representing conservation of mass and linear momentum. The latter applies subject to a generalized Beltrami condition to be satisfied by the magnetic field. This equivalence indicates that the compressible inviscid Navier-Stokes equations are Lorentz invariant as they derive directly from the Lorentz invariant Maxwell equations subject to the same Beltrami condition. In addition, the derivation results provide support for the claim that electromagnetic potentials have physical significance as demonstrated by Aharonov-Bohm effect, and are not only a convenient mathematical formulation.

In this work,the wave behaviour propagation of single-walled fluid conveying carbon nanotubes (SWCNT) under longitudinal magnetic fields and elastic foundations is studied, based on the nonlocal strain gradients theory(NSGT). With considertion of surface effect, the governing differential equation are obtained utilising Timoshenko beam theory and Hamilton's variational principle. The influence of small-scale parameters, fluid density, magnetic flux, surrounding elastic medium and surface effects on wave behaviour characteristics of carbon nanotubes are discussed in detail. The numerical results illustrated that with the magnetic flux increase，the phase velocities of the carbon nanotube will increase. When the fluid effects inside the carbon nanotube, the wave frequencies of the system reduces with increase in the non-local coefficient, while promotes with increase in the strain gradient coefficient. In addition, fluid density, surrounding elastic medium and surface effects have meaningful influence on the phase velocity of the system.

This work presents a design and model of the thermo-hydrodynamic behavior applying CFD for pin-fin heat sink with square shape (rectangular fin profile), through a novel pin arrangement that improves heat removal in the system. The novelty consist in the insertion of a deflector row that will help to direct the flow, so it hits the rectangular cross-sectional fins the presents in the system. The heat sink model is placed in channel designed in which air flows as suitable medium, and its overall performance is investigated. In addition, a constant heat flux is applied to the bottom wall of the heat sink model, equal values and amounts that​ correspond to the heat fluxes generated by current electronic equipment and devices. The numerical results of the global thermal resistance, the pressure drop and the Nusselt number are reported. The results allow determining best arrangement or geometry configuration, location and functionality of the fin-deflectors were collocated for evaluate thermal-hydraulic efficiency of system.

Human serum albumin (HSA) is the ultimate, homeostatic determinant of fluid volume (FV) in all compartments of the body. The ability to change the pressure and flow of nutrient medium to cellular structures selectively has clinical significance in almost all areas of clinical medicine. We have shown that present fluid therapy (FT) using either colloid or saline dilutes nutrients. HSA binds and delivers nutrients, a lack of HSA binding causes Albumin Binding Disease (ABD) changing both colloidal pressure and nutrients leading to symptoms of sepsis. A reduction in HSA binding can be through lack of HSA or external ligands taking up binding sites on HSA. Many diseases cause ABD when immunoglobulins, infectious particles and by products bind to HSA including COVID-19 and other bacterial diseases like streptococcus as well as metabolic and cardiac disease due to incorrect pressure and nutrients. To raise HSA binding potential and remove vulnerabilities to these diseases we propose raising HSA. We show how present methods of fluid therapy (FT) are inefficient in that control of both pressure and nutrients forms initial equilibrium in the liver. HSA production and binding to nutrients is maintained at a level by the pressure in hepatocytes with the pancreatic and adrenal hormones moderating. Glucose and Ke-tone production are critical in the management of HSA binding and control of blood, colloidal pressure, and health of cells. Ketones provide a distinct mechanism of liver to lungs-heart metabolism during hypoglycaemia and activity. This known chain of nutrition becomes critical during disease like acute respiratory distress syndrome (ARDS) when ketones may be overproduced. HSA must therefore be infused into the liver to raise HSA levels safely. We investigated the control of HSA as a product of the actions of pressure in hepatocytes and changes in pancreatic and adrenal hormones. We found that in addition to pressure during glucose abundancy HSA is re-leased with ketones on administration of insulin and consider that this mechanism retains HSA moderation. HSA can therefore be increased by increasing insulin in the presence of glucose in the correct amounts. We suggest a protocol to increase FV, blood, lymph volume by infusion of HSA, insulin, and glucose direct to the liver so that the level of HSA stabilises. We suggest this will raise all other nutrients in the new FV, blood, lymph culminating in the creation of new blood cells. We propose that in a clinical situation maintaining this protocol will alleviate the symptoms of ABD and decrease the likelihood of serious illness and death.

Purpose: We evaluated the outcomes of fluid-gas exchange (FGE) for long-term flap closure of idiopathic macular hole (MH) after the inverted internal limiting (ILM) flap technique. Methods: We included eyes showed flap closure without complete MH closure, connection of the apart macular tissue, 1 month postoperatively after the inverted ILM flap technique. The eyes stayed at flap closure at 2 months postoperatively further underwent in-office FGE with 16% C3F8. Results: Among 10 eyes, 5 eyes (50%) showed flap closure at 2 months postoperatively further underwent FGE for complete MH closure while the remaining 5 eyes (50%) progressed directly at 2 months postoperatively. The improvement in vision of all flap closure from baseline was significant (p=0.015), with the mean baseline vision was 1.19 [Snellen equivalent (SE), 20/307] ± 0.52 logMAR and the mean final vision being 0.63 (SE, 20/85) ± 0.38 logMAR. The group that underwent FGE showed a better final vision of 0.45 (SE, 20/75) ± 0.23 logMAR than the group that didn’t undergo FGE (0.81 [SE, 20/128] ±0.44 logMAR). All eyes achieved complete MH closure, including the eyes that underwent FGE in a mean period of 5.60 months (range 3-10 months) after the inverted ILM flap technique. The eyes that underwent FGE achieved higher rate of foveal restoration [complete external limiting membrane (ELM): 80%; complete ellipsoid zone (EZ): 60%] than those that didn’t receive FGE (complete ELM: 40%; complete EZ: 10%). Conclusions: Eyes that underwent FGE accelerated complete MH closure and showed better final vision and fovea l restoration.

For solving the fractional differential equations in computational fluid dynamics (CFD), it’s complicated and difficult by the Laplace and Fourier transforms. Based on the Caputo fractional derivative, the analytical solutions for unsteady unidirectional flows of a generalized Oldroyd-B fluid are deduced by the separation of variables method. Results show that the analytical solutions are given easily, and have good university. For some specific parameter values, the well-known analytical solutions for the generalized second grade fluid, the generalized Upper-Convected Maxwell (UCM) fluid as well as the ordinary Oldroyd-B fluid can be obtained.

Nowadays, energy saving is considered a key issue worldwide, as it brings a variety of benefits: reducing greenhouse gas emissions, reducing demand for energy imports, and lowering costs on a household and economy-wide level. Researchers and building designers are looking to optimize building efficiency by means of new energy technologies. Changes in existing buildings can also be made to reduce energy consumption and costs. These may include the usage of new heat transfer fluids based on nanofluids. In this work, an extended experimental campaign (from February 2020 to March 2021) has been carried out on an educational building in the Campus of University of Salento, Lecce – Italy, in order to evaluate the increase in performance of the HVAC system, due to the usage of a nanofluid. The results show that, under optimal operating conditions, plant performance improves more than 10%, with average daily peaks of about 15%.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

In the energy-momentum density expressions for a relativistic perfect fluid with a bulk motion, one comes across a couple of pressure-dependent terms, which though well known, are to an extent, lacking in their conceptual basis and the ensuing physical interpretation. In the expression for the energy density, the rest mass density along with the kinetic energy density of the fluid constituents due to their random motion, which contributes to the pressure as well, are already included. However, in a fluid with a bulk motion, there are, in addition, a couple of explicit, pressure-dependent terms in the energy-momentum densities, whose presence to an extent, is shrouded in mystery, especially from a physical perspective. We show here that one such pressure-dependent term appearing in the energy density, represents the work done by the fluid pressure against the Lorentz contraction during transition from the rest frame of the fluid to another frame in which the fluid has a bulk motion. This applies equally to the electromagnetic energy density of electrically charged systems in motion and explains in a natural manner an apparently paradoxical result that the field energy of a charged capacitor system decreases with an increase in the system velocity. The momentum density includes another pressure-dependent term, that represents an energy flow across the system, due to the opposite signs of work being done by pressure on two opposite sides of the moving fluid. From Maxwell's stress tensor we demonstrate that in the expression for electromagnetic momentum of an electric charged particle, it is the presence of a similar pressure term, arising from electrical self-repulsion forces in the charged sphere, that yields a natural explanation for the famous, more than a century old, 4/3 factor in the electromagnetic mass.

The deep Cretaceous tight sandstone in Kuqa Depression of Tarim foreland basin is an ultra-low porosity and ultra-deep gas-bearing reservoir, which is characterized by small pores, fine throats, and poor connectivity. The wireline logging responses are so complex, and especially, it is difficult to identify fluid types from resistivity logs. Based on acoustic, density, and neutron logs response differences in gas and water layers, effective fluid sensitivity factors are constructed for gas layer identification. From conventional logs, acoustic-neutron porosity difference, density-neutron porosity difference, and triple-porosity ratio are all sensitive parameters to the gas layer. From the NMR logging response mechanism, the density and NMR porosity difference, and T2 geometric mean of the movable fluid are also two sensitive parameters to the gas layer. Based on these parameters, a series of fluid typing charts are constructed and their adaptabilities are analyzed and compared. By contrast, NMR log interpretation is better, and triple-porosity comprehensive method from conventional logs is also effective when NMR logging is not available. Finally, the comprehensive fluid typing strategy by combining some methods for ultra-low porosity tight sandstone is summarized and optimized. This study is another alternative for fluid identification using non-electrical logs.

The asymmetry in the dynamics of an electro-pneumatic actuating device consisting of an electro-pneumatic transducer and a single-action pneumatic actuator was unexpectedly found experimentally. This asymmetry manifests in response to large step excitations. The dynamic asymmetry effect is understood as a change in the shape of the response of an actuator depending on the direction of the actuators stem movement. The questions appears: How to explain this effect? Does this phenomenon reflect thermodynamic air processes? Is it connected with air-to-mechanical energy conversion? Together, six working hypotheses explaining this effect were formulated. The asymmetry was studied in detail using analytical and simulation modeling, as well as experimental research. In this respect, a nonlinear analytical model was developed, tuned, and later solved using simulations. The simulation model was verified based on the experiment data. In addition, the problem of the efficiency in the energy conversion of a single-action actuator was discussed and, in result, the maximum theoretical energy efficiency was determined. Subsequently, all six working hypotheses were verified. Finally, the hypothesis explaining asymmetry as an effect of the different thermodynamic air processes in both actuator’s stem travel directions was confirmed.

An optical frequency comb (OFC) generator based on an electro-optic Talbot laser and cross-phase modulation (XPM) in a high nonlinear fiber (HNLF) is designed and demonstrated. The Talbot laser is an electro-optic frequency shifting loop to produce repetition rate multiplied pulses, and these pulses working as a pump signal induce XPM process in the HNLF to modulate the phase of a probe signal. At the output of the HNLF, OFCs with a multiplied line-spacing can be generated. The effects of the pump power and the HNLF length on the performance of the generated OFCs are theoretically analyzed. In the experiments, the line-spacing of the generated OFCs is respectively multiplied to be 10 GHz, 15 GHz and 20 GHz with a factor of 2, 3 and 4. The center of the OFCs is tuned in a 4-nm range by adjusting the wavelength of the probe signal.

The theory of water transport in trees, according to which the main driving force of water movement is the suction created by the evaporation of water by the meniscus (the curved surface of the capillary liquid column) on the evaporating elements, supported from below by root pressure, is flawed. The capillary effect in nature is around one meter. In the case of open-air gaps, the leaf cannot suck in the water against gravity because, in this case, the plant would not be sucking in water, but air through the open-air gap. If not, how do trees transport water? When evaporation occurs, there is no suction towards the canopy, but pressure is due to a reduction in the cross-section of the water pipe caused by heat loss through evaporation. At night, when evaporation stops, a thermal equilibration process is triggered, which restores the original cross-section of the pipe. This generates suction and draws water from the soil. As the hydrostatic pressure in the pipe is high for tall trees, the pipe is cut off. To prove my theory, I have given several examples. Water transport is not based on physical mechanical laws alone. There may be complex physiological, biochemical, and biophysical processes behind the operation of the pipe system.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

In order to the effect of hydrated phase change materials on suppressing coal spontaneous combustion, the thermogravimetric experiment and reaction activation energy analysis experiment were used to explore the changes of combustion characteristic, parameters characteristic temperature and activating energy of gas coal, long flame coal, meagre coal, and lean coal before and after adding hydrated phase change materials. The research results showed that hydrated phase change materials increased the coal samples’characteristic temperature point and have effective inhibitory effects on different stages of oxidation process.However, the effect was best at low temperatures, as hydrated phase change materials undergo phase change and absorb heat when heated at low temperatures, isolating coal from contact with oxygen. The activating energy increased by 1.138 KJmol-1～23.048 KJmol-1 and the mass loss reduced by 1.6%～9.3% after the inhibition of the coal sample,indicating that the oxidation rate of various coal samples can be slowed down and the spontaneous combustion can be suppressed by using hydrated phase change materials.At the same time, this material can also reduce the combustibility index of meagre coal and lean coal, as well as the comprehensive combustion index and maximum loss rate of long flame coal and gas coal.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

This study employs the phase-field regularized cohesion model (PF-CZM) to simulate crack propagation and damage behavior in porous granite. We investigate how pore radius (r), initial crack-pore distance (D), and pore-crack angle (θ) impact crack propagation. The simulation findings reveal that, with a fixed deflection angle and initial crack-pore distance, larger pores are more likely to induce crack extension under identical loading conditions. Moreover, with r and θ keeping constant, the crack extension can be divided into two stages: from its initiation to the lower edge of the pore and then from the lower edge to the upper boundary of the model. By varying the values of D and r, we derive multiple combinations of different D/r ratios and pore radii. These results demonstrate that with constant r, cracks tend to deflect toward the pore closer to the initial crack. Conversely, when D is maintained constant, cracks will preferentially deflect toward pores with a larger r. In summary, the numerical simulation of rock pores and initial cracks, based on the PF-CZM, exhibits remarkable predictive capabilities and holds significant potential in advancing rock fracture analysis.

Bimetallic colloidal CoPt nanoalloys, with a very low platinum content, were successfully synthesized following a modified polyol approach. Powder X-ray diffraction, IR spectroscopy, thermogravimetric analysis, and Transmission Electron Microscopy studies were performed to estimate the crystal structure, morphology and surface functionalization of the colloids respectively, while the room temperature magnetic properties were measured using Vibrating Sample Magnetometer. The particles exhibit excellent uniformity, with a narrow size distribution, and display strong room temperature hysteretic ferromagnetic behavior even in the as-made form. Upon annealing at elevated temperatures, progressive formation and co-existence of exchange coupled both chemically ordered and disordered phases, significantly enhance the room temperature coercivity.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

Early stable deep molecular response (DMR) of nilotinib is associated with goal of treatment-free remission (TFR) for patients with chronic-phase chronic myeloid leukemia (CML-CP). It is significant to early distinguish patients who can obtain DMR and fit for TFR. We performed a multicenter study to explore early cumulative MR4.5 rate by 18 months with nilotinib in patients with newly diagnosed CML-CP (ND-CML-CP) in China. From 29 institutes, 106 ND-CML-CP patients received nilotinib (300mg BID). The cumulative MR4.5 rate of nilotinib by 18 months was 69.8% (74/106). The cumulative MMR and MR4.0 rates of nilotinib by 18 months were 94.3% (100/106) and 84.9% (90/106), respectively. Patients with ultra-early molecular response (u-EMR) at 6 weeks were not significantly different to obtain DMR or MMR by 24 months compared to those without u-EMR (P=0.7584, P=0.9543, respectively). Our study demonstrated that treatment with nilotinib in patients with ND-CML-CP contributed to obtain high early MR4.5.

This study will present a comprehensive review of the two-phase flow boiling heat transfer coefficient of hydrocarbons such propane (R-290), butane (R-600) and iso-butane (R-600a) and ethanol at various experimental conditions. Studying the multiphase flow heat transfer coefficient has a crucial importance for many heat transfer equipment to achieve higher efficiency for more compact design and cost reduction. One reason behind choosing hydrocarbons as refrigerants in this study is because hydrocarbons have zero ozone depletion potential (ODP=0) and insignificant direct global warming potential (GWP = 3). Moreover, thermodynamic and thermophysical characteristics of hydrocarbons qualify them to be a strong candidate for more heat transfer applications. Initially, by constructing a database for the working fluids from various experimental work available in the literature. The current data that this study has collected for the flow boiling of spans wide ranges of parameters, such as: mass flux, heat flux, operating pressure, and saturation temperature, etc. Furthermore, by comparing the experimental multiphase heat transfer coefficient database with the anticipated values of each correlation, the prediction performance of 26 correlations found in the literature was assessed. This study leads to the selection of the best prediction method based on the minimum deviation of predicted results from the experimental database provided by calculated mean absolute error (MAE) from the assessed correlations. The findings of this study can also be useful in the development of more accurate correlation methods for these fluids and improve the prediction of their flow boiling characteristics.

Abstract: Self-regulated Learning has become one of educational psychology's most critical research areas. Contemporary research indicates that student creativity is crucial to the success of arts education. However, there is limited research on creativity in arts education in Self-regulated Learning. Therefore, this study aims to define the creativity characteristics that determine the quality of students’ work. This study implemented a creative competition in painting and composition for first-year undergraduates. It evaluated the characteristics of creativity during the three main phases of the task: planning, execution, and completion. We discovered through semi-open questionnaires (n=178)，and using the content analysis method. According to the competition results, the students with the highest scores in Flow, Inspiration, and Idea Generation in the Performance phase had the best quality work. In the Forethought phase, Analogical Thinking and Idea Generation worked best for most students, while in the Performance phase, Flow Sense, Idea Generation, and Idea Manipulation worked best.Data on creativity characteristics at different work phases and final quality might adequately guide and organize educational procedures. These findings can serve as a theoretical foundation for quantifying the creativity phase in Self-regulated Learning and offer arts educators a reference for creativity instruction.

An exact solution for the Nagel-Schreckenberg model for v_max = 1 is known since the 90s, yet for v_max > 1 it remains an open question. It is conjectured here that this general solution can be generated from the basic solution (for v_max = 1) by a linear coordinate transformation, the shear mapping, which requires no additional parameters in the deterministic case, and two additional parameters otherwise. The proposed solutions show remarkable agreement with existing numerical solutions, except in the congested regime where the Monte Carlo data shows more concavity than the more linear congested branches predicted by the theory. More research is needed to investigate this bias.

Voltage Source Inverters (VSI) are the integral part of Electrical Vehicles (EV) to enhance the reliability of supply power to critical loads in vehicle to load (V2L) applications. Inherent properties of sliding mode control (SMC) makes it one of the best vailable options to achieve desired voltage quality under variable load conditions. Intrinsic characteristic of robustness associated with SMC is achieved generally at the cost of unwanted chattering along the sliding surface. To manage this compromise better, optimal selection of sliding surface coefficient is applied with proposed composite exponential reaching law (C-ERL). The novelty of proposed C-ERL is associated with the intelligent mix of exponential, power and difference functions blended with rotating sliding surface selection (RSS) technique for three phase two level VSI. Moreover, proposed reaching law along with power rate exponential reaching law(PRERL), enhanced exponential reaching law(EERL) and repeatitive reaching law(RRL) are implemented on two level three phase VSI under variable load condtions. Comparative analysis of which strongly advocates the authenticity and effectiveness of proposed reaching law in achieving well regulated output voltage, with high level of robustness, reduced chattering and low %THD.

The term deviation frequency denotes the boundary between the variable part of the amplitude and phase scintillation spectrum and the part of uninformative noises. We suggested the concept of the “characteristic deviation frequency” during the observation period which is defined as the most probable value of the deviation frequency under current local conditions. This work is a case study of the characteristic deviation frequency (fd) registered for GPS, GLONASS, Galileo and SBAS signals under quiet and weakly disturbed geomagnetic conditions in April 2021 at the mid-latitude GNSS station. Our results demonstrated that the fd value for all signal components of GPS, GLONASS and GALILEO signals varied within 15-22 Hz. The characteristic deviation frequency was 20 Hz for the mentioned GNSS signals. In difference, the deviation frequency was limited within 13-20 Hz for SBAS with the lower characteristic deviation frequency at 18 Hz. We assume that the concept of the characteristic deviation frequency can be used to determine the optimal sampling rate of the GNSS carrier phase data for the ionospheric studies. The characteristic deviation frequency can also characterize the state of the regular trans-ionospheric radio channel.

This paper discusses the basic concepts of phase dislocations and vortex formation in the electric fields of fundamental air core mode of hollow core waveguides with specific types of rotational symmetry of the core – cladding boundary. Analysis of the behavior of the electric field phase in the transmission bands shows that the mechanism of light localization in the hollow core waveguides with discrete rotational symmetry of the core – cladding boundary cannot be completely described by the ARROW model. For an accurate description of the phase behavior, it is necessary to account for phase jumps of the magnitude of π when passing through the phase dislocations.

In this work, a small-strain phase-field model is presented, which is able to predict crack propagation in systems with anisotropic brittle and ductile constituents. To model the anisotropic brittle crack propagation, an anisotropic critical energy release rate is used. The brittle constituents behave linear-elastically, in a transversely isotropic manner. Ductile crack growth is realised by a special crack degradation function, depending on the accumulated plastic strain, which is calculated by following the J2-plasticity theory. The mechanical jump conditions are applied in solid-solid phase transition regions. The influence of the relevant model parameters on a crack, propagating through a planar brittle-ductile interface, and furthermore a crack developing in a domain with a single anisotropic brittle ellipsoid, embedded in a ductile matrix, is investigated. We demonstrate that important properties, concerning the mechanical behaviour of grey cast iron, such as the favoured growth of cracks along the graphite lamellae and the tension-compression load asymmetry of the stress-strain response, are covered by the model. The behaviour is analysed on basis of a simulation domain consisting of three differently oriented elliptical inclusions, embedded in a ductile matrix, which is subjected to tensile and compressive load. The used material parameters correspond to graphite lamellae and pearlite.

Two-dimensional mass spectrometry (2D MS) is a method for tandem mass spectrometry that relies on manipulating ion motions to correlate precursor and fragment ion signals. 2D mass spectra are obtained by performing a Fourier transform in both the precursor ion mass-to-charge ratio (m/z) dimension and the fragment ion m/z dimension. The phase of the ion signals evolves linearly in the precursor m/z dimension and quadratically in the fragment m/z dimension. This study demonstrates that phase-corrected absorption mode 2D mass spectrometry improves signal-to-noise ratios by a factor of 2 and resolving power by a factor of 2 in each dimension compared to magnitude mode. Furthermore, phase correction leads to an easier differentiation between ion signals and artefacts, and therefore easier data interpretation.

The aim of this work was to investigate the microstructure and the mechanical properties of la-ser-welded joints combined of DP800 and DP1000 high strength thin steel sheets. The welded joints (WJ) comprised of similar/dissimilar steels with similar/dissimilar thickness were consisted of different zones and exhibited similar microstructural characteristics. The trend of microhard-ness for all WJs was consistent, characterized of the highest value at hardening zone (HZ) and lowest at softening zone (SZ). The degree of softening was more severe and the size of SZ was wider in the WJ combinations of DP1000 than DP800. The tensile test fractures were located at the base material (BM) for all DP800 weldments, while the fractures occurred at the fusion zone (FZ) for the weldments with DP1000 and those with dissimilar sheet thicknesses. The DP800-DP1000 weldment presented similar yield strength (YS) and ultimate tensile strength (UTS) values but lower elongation (EI) in comparison with the DP800-DP800 weldment, which showed similar strength properties as the BM of DP800. However, the EI of DP1000-DP1000 weldment was much lower in comparison with the BM of DP1000. The DP800-DP1000 weldment with dissimilar thicknesses showed the highest YS and UTS values compared with the other weldments, but with the lowest EI. The fatigue fractures occurred at the WJ for all types of weldments. The DP800-DP800 weldment had the highest fatigue limit and DP800-DP1000 with dissimilar thick-nesses had the lowest fatigue limit. The fatigue crack initiated from the weld surface.

In the last years, the Distribution Grid Operators (DGOs) assumed transition strategies of the distribution grids towards an active area associated with the "Smart Grids" concept. They are considering the use of Artificial Intelligence techniques, combined with advanced technologies and real-time remote communication solutions of the enormous data amounts, to develop smart solutions into the small size distribution grids, also called microgrids (μGs). These solutions will provide support for the DGOs to ensure an optimal operation of the technical infrastructure of the μGs. In this context, a bi-level methodology for solving the phase load balancing problem in the μGs with complex topologies and a high number of single-phase consumers, considering a clustering-based selection criterion of the consumers for placement of the switching devices, was proposed in the paper. A real μG from a rural area, with 114 consumers integrated into the Smart Metering System (SMS), belonging to the DGO from Romania, was considered in testing the proposed methodology. An implementation degree of 17.5%, corresponding to the phase load balancing equipment installed to only 20 consumers from the μG, led to a faster computational time with 43% and reducing the number of switching operations by 92% than in the case of a full implementation degree (100%). The performance indicators related to the unbalance factor and energy-saving used in the evaluation of the technical benefits highlighted the efficiency of the proposed methodology.

Abstract: This study reviewed aspects of the biology of two members of the glucosinolate family, namely sinigrin and glucoraphanin and their anti-tumour and anti-microbial properties. Sinigrin and glucoraphanin are converted by the β-sulphoglucosidase myrosinase or the gut microbiota into their bioactive forms, allyl isothiocyanate (AITC) and sulphoraphanin (SFN) which constitute part of a sophisticated defence system plants developed over several hundred million years of evolution to protect them from parasitic attack from aphids, ticks, bacteria or nematodes. Delivery of these components from consumption of cruciferous vegetables rich in the glucosinolates also delivers many other members of the glucosinolate family so the dietary AITCs and SFN do not act in isolation. In-vitro experiments with purified AITC and SFN have demonstrated their therapeutic utility as antimicrobials against a range of clinically important bacteria and fungi. AITC and SFN are as potent as Vancomycin in the treatment of bacteria listed by the World Health Organisation as antibiotic-resistant "priority pathogens" and also act as anti- cancer agents through the induction of phase II antioxidant enzymes which inactivate potential carcinogens. Glucosinolates may be useful in the treatment of biofilms formed on medical implants and catheters by problematic pathogenic bacteria such as Pseudomonas aeruginosa and Staphylococcus aureus and are potent antimicrobials against a range of clinically important bacteria and fungi. The glucosinolates have also been applied in the prevention of bacterial and fungal spoilage of food products in advanced atmospheric packaging technology which improves the shelf-life of these products.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

Printed electronic devices are attracting significant interest due to their versatility and low cost; however, quality control during manufacturing is a significant challenge, preventing the widespread adoption of this promising technology. We show that terahertz (THz) radiation can be used for the in situ inspection of printed electronic devices, as confirmed through a comparison with conventional electrical conductivity methods. Our in situ method consists of printing a simple test pattern exhibiting a distinct signature in the THz range that enables the precise characterization of {the static} electrical conductivities of the printed ink. We demonstrate that contactless dual-wavelength THz spectroscopy analysis, which requires only a single THz measurement, is more precise and repeatable than the conventional four-point probe conductivity measurement method. Our results open the door to a simple strategy for performing contactless quality control in real time of printed electronic devices at any stage of its production line.

We describe the direct formation of mixed-phase (1T and 2H) MoS2 layers on Si as a photocathode via atomic layer deposition (ALD) for application in the photoelectrochemical (PEC) reduction of water to hydrogen. Without typical series-metal interfaces between Si and MoS2, our p-Si/SiOx/MoS2 photocathode showed efficient and stable operation in hydrogen evolution reactions (HERs). The resulting performance could be explained by spatially genuine device architectures in three dimensions (that is, laterally homo and vertically heterojunction structures). The ALD-grown MoS2 overlayer with the mixed-phase 1T and 2H homojunction passivates light absorber and surface states and functions as a monolithic structure for effective charge transport within MoS2. It is also beneficial in the operation of p-i-n heterojunctions with inhomogeneous barrier heights due to the presence of mixed-phase cocatalysts. The effective barrier heights reached up to 0.8 eV with optimized MoS2 thicknesses, leading to a 670 mV photovoltage enhancement without employing buried Si p-n junctions. The fast-transient behaviors via light illumination show that the mixed-phase layered chalcogenides can serve as efficient cocatalysts by depinning the Fermi levels at the interfaces. A long-term operation of ~ 70 h was also demonstrated in a 0.5 M H2SO4 solution.

In this study, the use of recycled diatomaceous earth as the extraction phase in a the solid phase microextraction (SPME) technique for the determination of polycyclic aromatic hydrocarbons (PAHs) in river water samples, with separation/detection performed by gas chromatography-mass spectrometry (GC-MS), is proposed. The optimized extraction conditions are extraction time 70 min at 80 ºC with no addition of salt. The limits of quantification were close to 0.5 μg L-1 with RSD values lower than 25% (n = 3). The linear working range was 0.5 μg L-1 to 25 μg L-1 for all analytes. The method was applied to samples collected from the Itajaí River (Santa Catarina, Brazil) and the RSD values for repeatability and reproducibility were lower than 15% and 17%, respectively. The efficiency of the recycled diatomaceous earth fiber was compared with that of commercial fibers and good results were obtained, confirming that this is a promising option for use as the extraction phase in SPME.

Batch combustion in wood log stoves is a promising application for latent heat storage (LHS), due to the transient heat production with high peak effects. The current study aimed at designing a compact, passive and durable LHS system storing a substantial part of the heat release during batch combustion and effectively releasing the stored heat to the room for 6 to 10 hours after the last batch. The LHS system consists of a coaxial cylinder located at the top of the wood stove, replacing part of the regular stovepipe. Internal metallic fins were applied as heat transfer enhancement to homogenize the temperature distribution inside the PCM. The effect of radial fin lengths was numerically investigated through a parametric study using five different fin lengths within the PCM. Using 35-mm fins in the 70-mm PCM layer yielded the best trade-off for the application. This configuration enabled achieving a slow but close to complete melting of the PCM within a realistic combustion duration, while avoiding overheating the PCM above its degradation temperature. Thereafter, the discharge allowed releasing the stored latent heat for 6 hours. The exhaust gas inlet temperature proved to have a strong influence on the PCM thermal performance.

A phenomenological constitutive model is developed to describe the uniaxial transformation ratcheting behaviors of super–elastic shape memory alloy (SMA) by employing a cosine–type phase transformation equation with the initial martensite evolution coefficient that can capture the feature of the predictive residual martensite accumulation evolution and the nonlinear hysteresis loop on a finite element (FE) analysis framework. The effect of the applied loading level on transformation ratcheting are considered in the proposed model. The evolutions of transformation ratcheting and transformation stresses are constructed as the function of the accumulated residual martensite volume fraction. The FE implementation of the proposed model is carried out for the numerical analysis of transformation ratcheting of the SMA bar element. The integration algorithm and the expression of consistent tangent modulus are deduced in a new form for the forward and reverse transformation. The numerical results are compared with those of existing model and the experimental results to show the validity of the proposed model and its FE implementation in transformation ratcheting. Finally, a FE modeling is established for a repeated preload analysis of SMA bolted joint

It was demonstrated during the past decade that ultra-short intense laser pulse tightly focused deep inside a transparent dielectric generates the energy density in excess of several MJ/cm$^3$. Such energy concentration with extremely high heating and quenching rates leads to unusual solid-plasma-solid transformation paths overcoming kinetic barriers to formation of previously unknown high-pressure material phases, which are preserved in the surrounding pristine crystal. These results were obtained with the pulse of Gaussian shape in space and in time. Recently it was shown that the Bessel-shaped pulse could transform much larger amount of a material and allegedly create even higher energy density than that was achieved with the Gaussian (GB) pulses. Here we present a succinct review of previous results and discuss the possible routes for achieving higher energy density employing the Bessel beams (BB) and take advantage of its unique properties.

Quantitative phase microscopy (QPM), a technique combining phase imaging and microscopy, enables visualization of the 3-D topography in reflective samples as well as the inner structure or refractive index distribution of transparent and translucent samples. However, as in conventional optical microscopy, QPM provides either a large field of view (FOV) or a high resolution but not both. Many approaches such as oblique illumination, structured illumination and speckle illumination have been proposed to improve the spatial resolution of phase microscopy by restricting other degrees of freedom (mostly time). Therefore, the space bandwidth product (SBP) of QPM becomes enlarged. This paper aims to provide an up-to-date review on the resolution enhancement approaches of QPM, discussing the pros and cons of each technique as well as the confusion on resolution definition claim on QPM and other coherent microscopy.

Owing to the nondiffracting, self-accelerating, and self-healing properties, Airy beams of different nature have become a subject of immense interest in the past decade. Their interesting properties have opened doors to many diverse applications. Consequently, the questions of how to properly design spatial manipulation of Airy beams or how to implement them in different setups have become important and timely in the development of various optical devices. Here, based on our previous work, we present a short review on the spatial control of Airy beams, including the interactions of Airy beams in nonlinear media, beam propagation in harmonic potential, and the dynamics of abruptly autofocusing Airy beams in the presence of a dynamic linear potential. We demonstrate that under the guidance of nonlinearity and external potential, the trajectory, acceleration, structure, and even the basic properties of Airy beams can be adjusted to suit specific needs. We describe other fascinating phenomena observed with Airy beams, such as self-Fourier transformation, periodic inversion of Airy beams, and the appearance of spatial solitons in the presence of nonlinearity. These results have promoted the development of Airy beams, and have been utilized in various applications, including particle manipulation, self-trapping, and electronic matter waves.

Molecularly imprinted polymers (MIPs) were synthesized and applied for the selective extraction of oblongifolin C (OC) from fruit extracts of Garcinia yunnanensis Hu. A series of experiments and computational approaches were employed to improve the efficiency of screening for optimal MIP systems in the study. The molar ratio (1:4) was chosen at last based on the comparison of the binding energy of the complexes between the template (OC) and functional monomers using density functional theory (DFT) at the RI-PBE-D3-gCP/def2-TZVP level of theory. The binding characterization and the molecular recognition mechanism of MIPs were further explained using the molecular modeling method and NMR and IR spectra data. The reusability of this approach was demonstrated in over 20 batch rebinding experiments. 140.5 mg of OC (>95% purity) was obtained from the 5 g extracts with 2 g of MIPs with the best binding properties through gradient elution program from 35% to 70% methanol-water solution. At the same time, another structural analog, 46.5 mg of guttiferone K (GK) (>88% purity), was also obtained by the gradient elution procedure. Our results showed that the structural analogs could be separated from the crude extracts by the molecularly imprinted solid-phase extraction (MISPE) using a gradient elution procedure for the first time.