This paper discusses about control of the linear switched reluctance machines (LSRMs) network for the zero phase-difference tracking to a sinusoidal reference. The dynamics of each LSRM is derived by online system identification and modeled as a second-order linear system. Accordingly, based on the coupled harmonic oscillators synchronization manner, a distributed control is proposed to synchronize each LSRM state to a virtual LSRM node representing the external sinusoidal reference for tracking it with zero phase-difference. Subsequently, a simulation scenario and an experimental platform with the identical parameter setup are designed to investigate the tracking performance of the LSRMs network constructed by the proposed distributed control. Finally, the simulation and experimental results verify the effectiveness of the proposed LSRMs network controller, and also prove that the coupled harmonic oscillators synchronization method can improve the synchronization tracking performance and precision.

We tested the use of mosquito traps as an alternative to insecticide spraying in Camargue (France) following the significant impacts observed on the non-target fauna through Bti persistence and trophic perturbations. In a village of 600 inhabitants, 16 Techno-Bam traps emitting CO₂ and using octenol lures were set from April to November 2016. Trap performance was estimated at 70% overall based on mosquito landing on human baits in areas with and without traps. Reduction of Ochlerotatus caspius and Oc. detritus, the two species targeted by Bti spraying, was respectively 74 and 98%. Traps were less efficient against Anopheles hyrcanus (46%), which was more attracted by lactic-acid than octenol lures based on previous tests. Nearly 300 000 mosquitoes from nine species were captured, with large variations among traps, emphasizing that trap performance is also influenced by surrounding factors. Environmental impact, based on the proportion of non-target insects captured, was mostly limited to small chironomids attracted by street lights. Breeding success of a house martin colony was not significantly affected by trap use, in contrast to Bti spraying. Our experiment confirms that deployment of mosquito traps can offer a cost-effective alternative to Bti spraying for protecting local populations from mosquito nuisance in sensitive natural areas.

In the last decades synthetic jet actuators have gained much interest among the flow control techniques due to their short response time, high jet velocity and absence of traditional piping, that matches the requirements of reduced size and low weight. A synthetic jet is generated by the diaphragm oscillation (generally driven by a piezoelectric element) in a relatively small cavity, producing periodic cavity pressure variations associated with cavity volume changes. The pressured air exhausts through an orifice, converting diaphragm electrodynamic energy into jet kinetic energy. This review paper faces the development of various lumped-element models (LEMs) as practical tools to design and manufacture the actuators. LEMs can quickly predict device performances such as the frequency response in terms of diaphragm displacement, cavity pressure and jet velocity, as well as the efficiency of energy conversion of input Joule power into useful kinetic power of air jet. The actuator performance is analyzed also by varying typical geometric parameters such as cavity height and orifice diameter and length, through a suited dimensionless form of the governing equations. A comprehensive and detailed physical modeling aimed to evaluate the device efficiency is introduced, shedding light on the different stages involved in the process. Overall, the influence of the coupling degree of the two oscillators, the diaphragm and the Helmholtz’s one, on the device performance is discussed throughout the paper.

Count data are used in many fields of practice, especially Poisson distribution as a popular choice for the marginal process distribution. If these counts exhibit serial dependence, a popular approach is to use a Poisson INAR(1) model to describe the autocorrelation structure of process. In this paper, the explicit formulas are proposed to evaluate performance characteristics of Double Moving Average control chart (DMA) for Integer valued autoregressive of serial dependence Poisson process. The characteristics of the control chart are frequently measured as Average Run Length (ARL) which means that the average of observations are taken before a system is signaled to be out-of-control. These proposed explicit formulas of ARL are simple and easy to implement for practitioner. The numerical results show that the DMA chart performs better than others when the magnitudes of shift are moderate and large.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

Distracted driving is the leading cause of accidents, the cause of these distractions may include drowsiness, using cell phone, smoking a cigarette, etc. The proposed paper aims at monitoring the attentiveness of the driver and alerting the driver when his/her alertness goes below a certain threshold. It uses image processing using OpenCV (Computer Vision) and You Look Only Once (YOLO) algorithm to detect the eyes and object respectively and sounds an alarm when the driver is either drowsy or using his cell phone or smoking a cigarette.

More than 700 thousand human deaths from mosquito bites are observed annually in the world. It is more than 2 times the number of annual murders in the world. In this regard, the invention of new more effective methods of protection against mosquitoes is necessary. In this article for the first time, comprehensive studies of mosquito neutralization using machine vision and a 1 W power laser are considered. Developed laser installation with Raspberry Pi that changing the direction of the laser with a galvanometer. We developed a program for mosquito tracking in real. The possibility of using deep neural networks, Haar cascades, machine learning for mosquito recognition was considered. We considered in detail the classification problems of mosquitoes in images. A recommendation is given for the implementation of this device based on a microcontroller for subsequent use as part of an unmanned aerial vehicle. Any harmful insects in the fields can be used as objects for control.

Exoskeleton robots have become a promising tool in neurorehabilitation, offering effective physical therapy and recovery monitoring. The success of these therapies relies on precise motion control systems. Although computed torque control based on inverse dynamics provides a robust theoretical foundation, its practical application in rehabilitation is limited by its sensitivity to model accuracy, making it less effective when dealing with unpredictable payloads. To overcome these limitations, this study introduces a novel model reference computed torque controller that accounts for parametric uncertainties while optimizing computational efficiency. A dynamic model of a seven-degree-of-freedom human lower limb exoskeleton is developed, incorporating a realistic joint friction model to accurately reflect the physical behavior of the robot. To reduce computational demands, the control system is split into two loops: a slower loop that predicts joint torque requirements based on input trajectories and robot dynamics, and a faster PID loop that corrects trajectory tracking errors. Coriolis and centrifugal forces are excluded from the model due to their minimal impact on system dynamics relative to their computational cost. Experimental results show high accuracy in trajectory tracking, and statistical analyses confirm the controller’s robustness and effectiveness in handling parametric uncertainties. This approach presents a promising advancement for improving the stability and performance of exoskeleton-based neurorehabilitation.

Fairness-related decision-making often involves a conflict between egoistic and prosocial motives. Previous research based on Terror Management Theory (TMT) indicates that mortality salience can promote both selfish and prosocial behaviors, leaving its effect on fairness-related decision-making uncertain. By integrating TMT with the strength model of self-control, we propose that managing death-related thoughts depletes self-control strength, thereby impairing individuals' ability to resist selfish impulses during fairness-related decision-making tasks. Additionally, this effect is moderated by dispositional self-control. We tested these hypotheses in two studies. Participants were primed with either mortality salience or negative affect and then asked to made a series of binary choices (equal allocation vs. unequal allocation favoring themselves) to distribute monetary resources. In both studies, mortality salience heightened selfish tendencies, leading allocate resources less equitably. Study 2 further revealed that this effect occurred among participants with low, but not high, self-control. These findings indicate that mortality salience promotes selfishness and inequitable resource allocation, but that self-control can buffer these effects.

Results: This case series study included 20 PD participants with STN-DBS, with a mean age of 61.2±10.1 years. There were no differences in equilibrium scores of SOT conditions between 60, 130, and 180 Hz frequencies (p> 0.05), except the SOT6 score (p= 0.003), where 60 Hz showed better equilibrium performance in SOT6, indicating an advantage in postural control when visual and somatosensory cues are disturbed, and vestibular cues are not.

This study investigates the efficacy of an integrated rehabilitation program that combines vestibular and knee-focused therapies to improve proprioceptive function, balance, and motor control in patients suffering from both Benign Paroxysmal Positional Vertigo (BPPV) and knee joint conditions. The study involved 59 participants diagnosed with both vestibular dysfunction and knee impairments, who were enrolled in a comprehensive rehabilitation program. Vestibular interventions included specific maneuvers such as the Epley maneuver and Brandt-Daroff exercises, aimed at repositioning otoliths and reducing vertigo symptoms, while balance retraining exercises were implemented to enhance stability and prevent falls. Additionally, TECAR therapy was used for its deep tissue heating and regenerative benefits, and specific proprioceptive exercises targeting the knee joint were conducted to improve joint position sense and reduce the risk of falls. The intervention resulted in significant improvements in proprioceptive accuracy, as evidenced by enhanced joint position sense measurements and increased scores on the Dynamic Gait Index (DGI). These findings suggest that the dual-targeted rehabilitation approach not only addresses the individual impairments associated with vestibular dysfunction and knee pathology but also effectively improves overall functional outcomes by tackling the complex interplay between these conditions. The study further highlights the importance of a multidisciplinary approach in rehabilitation, where addressing vestibular and musculoskeletal dysfunctions simultaneously can lead to better patient outcomes. The integrated rehabilitation strategy presented in this study offers a comprehensive approach to managing complex clinical cases, ultimately contributing to improved quality of life and functional independence in patients affected by concurrent vestibular and knee joint issues.

Introduction: Low back pain (LBP) is the leading cause of lost productivity, absenteeism, disability, and early retirement worldwide. LBP treatment should be comprehensive, including prevention, education, diagnosis, and various treatment methods. Treatment can be divided into pharmacological and non-pharmacological. The role of physiotherapy in the comprehensive treatment of LBP is very important. Elastic therapeutic tape, also called kinesiology tape or therapeutic kinesiology tape, has been used for about 50 years. Purpose: The aim of this study was to evaluate the effectiveness of Kinesio taping in patients suffering from (LBP) and its possible effect on the swing of the center of pressure (COP), balance, gait, improvement of coordination, and pain reduction. Material and methods: A total of 60 patients aged 20 to 83 years (54% women) were examined, all of whom met the inclusion and exclusion criteria. In the experimental group, in addition to comprehensive rehabilitation, kinesiotaping of the L1-L5 spine was used. The control group underwent balance control training. The research tools used included the Bohannon single-leg standing test, the FAC scale - Functional Ambulatory Category, the Podsiadlo and Richardson Standing and Walking Test - Timed Up and Go (TUG), lumbar spine mobility assessment, Lasegue's sign and examination of neurological deficit symptoms. and self-assessment of pain using the Visual Analogue Scale (VAS). Results: Kinesio taping has a statistically significant effect on postural control, balance, gait, coordination, and pain. The main parameter with a statistically significant effect on the effects of Kinesio taping was age (below 55 years), which was also observed in the control group. Conclusions: Kinesio taping is an effective method in the treatment of LBP. It improves postural control, balance, gait, coordination, and pain.

A medium scale household in South Africa consumes about 1000 kWh on average, and ae household spend about 3000 ZAR per month on energy supply using grid electricity. Grid electricity. South Africa’s energy is supplied by a huge governmental organization. Statistical analyses indicate that projected increase of the cost of grid electricity in South Africa is about 30% per annum for the next five years. Our research show that Photo-Voltaic (PV) technology can offer a viable alternative, provided a large initial capital outlay can be made. The technology is user-friendly and easy to operate. It is calculated that the cost of electricity, capitalized over 20 years, considering an 80 % supply of needs and assuming 20 sunny days per month, is about 2.80 ZAR. The study also shows that utilizing a hybrid combination of renewable energies, such as combining PV supply with solar thermal energy absorbers, and converting thermal energy to electricity, as energy supply systems, could reduce the current cost of electricity per household in South Africa to about half of national grid supply prize, R1,50 per kWhr. The study also shows that water provides as a most viable medium to store energy, instead of using expensive battery technology to perform such functions.

Reducing visceral fat is an important issue for obesity prevention. We previously reported a novel dietary intervention program using “Optimized Nutri-Dense Meals” based on the nutrients described in Dietary Reference Intakes in Japan. This open-label randomized controlled trial evaluated the visceral fat reducing effect of the program. In total, 100 Japanese obese/overweight male patients were recruited and divided into a control group that continued their usual diets and a test group that consumed test meals twice per weekday for four weeks. Visceral fat area, set as the primary outcome, was significantly decreased in the test group compared with the control group. Regarding other outcomes, the occupancy levels of some gut floras and presenteeism scores were significantly increased in the test group compared with the control group. These results indicate that dietary intervention based on the Dietary Reference Intakes can prevent visceral fat accumulation and contribute to the improvement of health, without the need for completely replacing the everyday diet.

Aedes albopictus is considered one of the major invasive species in the world and can transmit viruses such as dengue, Zika, or chikungunya. The Sterile Insect Technique (SIT) can be used to suppress the native populations of Ae. albopictus. To support the development of the release strategy during the SIT application, Mark-Release-Recapture (MRR) studies are crucial. Mean-while, weather conditions can affect the MRR trial’s results and it is critical to understand the influence of climatic factors on the results. In October 2022 in Faro, Southern Portugal, 84,000 ir-radiated sterile males were released for three consecutive weeks and mosquitoes were recapture by Human Landing Collections (HLC) one, two, four and six days after. Generalised linear models with a negative binomial family and log function were used to estimate the factors asso-ciated with the number of recaptured mosquitoes, prevalence ratios, and the 95% confidence in-tervals (CI). A total of 84,000 sterile male mosquitoes were released, with 528 recaptured (0.8%) by HLC. The prevalence of recaptured mosquitoes was 23% lower when the wind intensity was moderate. Sterile-marked males had an average median distance travelled of 88.7 m. Median probability of daily survival and the average life expectancy were 61.6% and 2.1, respectively. Wild male population estimates was 443.33 males/ ha. Despite no statistically significant asso-ciation was found with humidity, temperature and precipitation, it is crucial to consider weather conditions during MRR trials analyses to obtain the best determinants estimation and a more ef-ficient application of SIT in an integrated vector management program.

Fiscal control and monitoring of public management are issues of great importance and relevance, as they focus on preventing and mitigating corruption, thus benefiting governments in their management and performance, and thus citizens. Given the large amount of data involved in the management and functioning of a government, it is pertinent to apply data analysis methods to contribute to fiscal control. This paper aims to investigate data management for this purpose, starting with a bibliometric study to demonstrate the relevance and pertinence of the current study. It examines existing data collection techniques that may facilitate such control, data storage considering its nature and the possibilities that contribute to this end, and data processing through techniques that allow obtaining adequate information for further analysis and decision making. The necessary architecture and interoperability between systems is also discussed, as the existence of large amounts and types of data in governments makes it crucial to promote these practices for accurate and truthful analysis. Finally, data visualization is addressed since this topic is highly relevant as it allows for the identification of anomalies, where proper visualization promotes appropriate analysis and thus informed decision making. This work is useful for modern audit and fiscal control entities, since data capture, storage, processing, interoperability, and visualization are crucial elements that collectively enhance the ability to supervise public expenditure effectively, ensuring that public funds are managed with the highest standards of transparency, accountability, and efficiency.

As modern systems are becoming more complex their control strategy cannot longer relay only on measurement information that usually comes from probes but also from mathematical models. Those systems models can lead to unbearable computation times due to their own complexity, turning the control process non-viable, which leads to the implementation of surrogate models that enable to achieve estimates within acceptable time to take decisions. A control trained with Deep Reinforcement Learning algorithm, using a Physics-Informed Neural Network to obtain the temperature map on the following time step, replaces the need of running Direct Numerical Simulations. On this work we considered an 1D heat conduction problem, which temperature distribution feeds a control system to activate a heat source aiming to obtain a constant, previously defined, temperature value. With this approach, control training becomes much faster without the need of performing numerical simulations or laboratory measurements, as well the control is taken based on Neural Network enabling its implementation on simple processors to edge computing.

The layer-by-layer (LBL) fabrication method allows for controlled microstructure morphology and vertical component distribution, and also offers a reproducible and efficient technique for fabricating large-scale organic solar cells (OSCs). In this study, polymer D18 and PYIT-OD are employed to fabricate all-polymer solar cells (all-PSCs) using the LBL method. Morphological studies reveal that the use of additives optimizes the microstructure of the active layer, enhancing the crystallinity and charge transport capability. The optimized device with 2% CN additive significantly reduces bimolecular recombination and trap-assisted recombination. All-PSCs fabricated by the LBL method based on D18/PYIT-OD deliver a power conversion efficiency (PCE) of 15.07%. Our study demonstrates the great potential of additive engineering via LBL fabrication method in regulating microstructure of active layers, suppressing charge recombination, and enhancing the photovoltaic performance of devices.

Panax notoginseng (Burk.) F. H. Chen, a valuable Chinese herb in Yunnan Province, is susceptible to leaf spot caused by Boeremia linicola. Nonetheless, effective control methods against leaf spot in P. notoginseng are lacking. We surveyed understorey P. notoginseng bases in Lincang, Lancang, and Xundian, with incidence rate reaching 80% and an average disease index of 25 in severe cases. We found that pathogenic bacteria overwinter in infected leaves and soil, with conidia and conidiophores serving as the primary infection source. The strain B. linicola LYB-2 showed the best growth at 20°C and pH 5.0. We also screened control agents using the plate and face-off culture methods. Tetramycin exhibited 38.56–74.67% inhibition with an EC50 of 0.60 mg/L. Copper abietate showed 3.10–34.76% inhibition with an EC50 of 3,120.05 mg/L. Trichoderma atroviride and T. harzianum exhibited inhibition rates of 52.48% and 44.19%, respectively, while Bacillus subtilis reached 78.45%. Field tests demonstrated significant control effects with 20% copper abresinate, B. subtilis, T. virenceae BH-10 preparation, and 0.3% tetramycin, achieving 82.57%, 72.56%, 71.3%, and 70.2% inhibition, respectively. These findings support their eco-friendly use for preventing and controlling leaf spot disease in P. notoginseng forests; we provide vital scientific evidence for disease prediction and green control strategies.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

: This paper presents a comparison between direct integer orders or classical model reference adaptive control (IO-DMRAC) versus its fractional orders counterpart (FO-DMRAC) applied to the F-16 aircraft longitudinal model pitch rate control. A substantial improvement is achieved when using fractional order adaptive control, since, in addition to performance indices, such as Integral Square-Error criterion (ISE) and Integral Square-Input criterion (ISU) being lower, the oscillations of the system output (pitch rate) in the transient period, are eliminated. Moreover, it is the first attempt in literature of adaptive control that a FO-DMRAC is applied to the pitch rate control of an aircraft. A F-16 short-period model, whose relative degree is equal to 1 (n^*=1) is analyzed by mean of simulations with good results. A FO-DMRAC is designed, for a specific operating flight conditions and compared with its IO-DMRAC counterpart. Furthermore, the boundedness of all signals, including the internal ones ω(t) are assured.

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimising MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based-control and deep learning techniques, including gated recurrent units (GRU), basic recurrent neural network (RNN) and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimises MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyper-parameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R2 value close to 1, representing a strong correlation between predicted and actual power values.

A difficult open problem that has never been fully resolved in the literature to date is the behaviour of the (TDCDP) third approximation. As a giant step towards modern control theory, this cutting-edge paper will advance control theory and other relevant inter-disciplinary subjects. Because control theory is important in industry and engineering, this study will be especially beneficial to anyone working in these disciplines who wish to understand more about recent advances in control theory settings. In contrast, the wealth of applications of Fokker Planck Kolmogorov (FPK) equations numerous disciplines As a result, the study instantly gains more taste and credibility. At the end of the paper, there are several challenging open problems, some concluding remarks, and recommendations for further investigation.

Bacteria belonging to the genus Micromonospora are recognized as microorganisms with potential to be used in biotechnology processes, including their beneficial influence on plant growth and biocontrol of phytopathogens. In this study, nineteen Micromonospora isolates originating from root nodules of white clover plants were taxonomically assigned based on the phylogenetic analysis of the 16S rRNA gene and four housekeeping genes. The antifungal properties of the bacteria against phytopathogenic Botrytis cinerea, Fusarium oxysporum, Fusarium equiseti, Sclerotinia sclerotiorum, and Verticillium albo-atrum were tested with the agar plug test and the dual culture test. The ability to produce various metallophores was determined with the agar plug diffusion test on modified CAS agar medium. ISP2 broth amended with 0.2% L-tryptophan was used to indicate the bacterial ability to produce auxins. Strains belonging to M. tulbaghiae, M. inaquosa, and M. violae showed in vitro potential as antimicrobial agents against the tested fungi. M. inaquosa strain 152, M. violae strain 126, M. violae strain 66 and M. violae strain 45 were recognized as the most efficiency metallophores producers. M. alfalfae strain 55 and M. lupini strain 5052 were identified as the most promising auxin compound producers and, therefore, as potential plant growth promoting bacteria.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

Acute and chronic graft versus host disease (a/cGVHD) are major complications of allogeneic stem cell transplantation and a frequent cause of non relapse-mortality. The treatment of a/cGVHD consists of steroid administration at full dose. In the case of aGVHD, around 60 % of patients with grade III/IV fails to respond (steroid-resistant, SR), requiring a second line therapy. Extracorporeal photopheresis (ECP) represents a good option for second line treatment, leading to multiorgan response in several patients. Here, we have evaluated the performances of a cytofluorimetric quality control of the first ECP procedure in 29 patients with severe SR aGVHD who underwent ECP. The quality control represents a check control of in vitro cell apoptosis/death induction in collected and irradiated CD3+ cells by ECP. Our analysis shows that in more than 70 % quality controls a relevant apoptotosis/death of CD3+ cells was observed after cell irradiation, as compared to non-irradiated controls. Albeit observed in a small patients’ series, the occurrence of relevant in vitro effect after ECP relates to less procedures and/or to a better survival on ECP. Age, disease, gender, aGVHD grade and time from transplant to the first ECP had not impact on ECP efficacy in this patients’ series.

This analytical cross-sectional study was designed to evaluate the association between glycemic control and peripheral arterial disease in patients with diabetic foot with more than ten years of evolution of diabetes mellitus who attended the diabetic foot outpatient clinic of the Guillermo Almenara National Hospital between June 2015 and February 2017. Glycosylated hemoglobin (HbA1C) and ankle-brachial index (ABI) were used to diagnose glycemic control and peripheral arterial disease, respectively. A generalized Poisson log-linear regression model was used to calculate the crude (cPR) and adjusted (aPR) prevalence ratios, with 95% confidence intervals, and a significance level of p < 0.05. 226 patients were included in the study, finding 23% (n=52) with good glycemic control, and 44.7% (n=101) with peripheral arterial disease. The adjusted model found statistically significant associations for glycemic control, age, and sedentary lifestyle with peripheral arterial disease. Compared with patients with good glycemic control, those with poor glycemic control had a 34% higher probability of presenting peripheral arterial disease (aPR: 1.34, 95%CI: 1.01-1.79, p=0.045). The prevalence of good glycemic control in the population with diabetic foot is low. Poor glycemic control was found to be independently associated with the presence of peripheral arterial disease.

Edible oils have commercial and nutritional value due to the presence of essential fatty acids. They can be consumed fresh in the form of capsules known as nutraceuticals. The quality of such products is of interest to the consumer. In this context, this study describes a method based on high resolution nuclear magnetic resonance (NMR) and Fourier transform mid-infrared spectroscopic analysis (FTIR), combined with statistical analyzes to differentiate different edible oils used as nutraceuticals in Brazil by fatty acid content. Through the analysis of 1H NMR spectra, the levels of saturated and unsaturated fatty acids in edible oils were characterized and quantified. Statistical analysis of the data confirmed the real distinction between nutraceutical raw materials, with emphasis on ω-9, ω-6 and ω-3 fatty acids. The analytical approach presented also demonstrated potential to identify the origin (animal or vegetable) of edible oils used as nutraceuticals.

Salinity is one of the major factors responsible for the deterioration of soils, making them unsuitable for agriculture. The application of halotolerant and halophilic plant growth promoting bacteria (PGPR: Plant Growth Promoting Rhizobacteria) with biological control activities as an inoculant of cultivated plants offers a biological alternative to the use of agrochemicals, particularly when subjected to salt stress. In this perspective, 70 bacterial strains were isolated from saline soils (sebkha) in arid and semi-arid areas of eastern Algeria. Three isolates were selected based on their ability to produce bioactive molecules allowing them to promote plant growth, such as hydrolytic enzymes, indole acetic acid, HCN, NH3, etc. Two of these isolates belong to the genus Serratia and the third is a halophilic Halomonas bacteria. These bacteria were identified based on the 16S rDNA sequence. Antagonism tests against phytopathogenic fungi were carried out. The identification of the antifungal molecules produced by these bacteria was done by high performance liquid chromatography. These bacteria are capable of inhibiting mycelial development against phytopathogenic fungi with rates reaching 80.67% against Botrytis cinerea, 76.22% against Aspergillus niger and 66.67% against Fusarium culmorum for Serratia sp. The strain Halomonas sp. inhibited mycelial growth by production of volatile substances of Aspergillus niger at 71.29%, Aspergillus flavus at 75.49% and Penicillium glabrum at a rate of 72.22%. The identification by HPLC of the antifungal molecules produced by these three bacteria reveals that they are polyphenols, which makes these strains the first rhizobacteria capable of producing phenolic compounds. Finally, pot tests to determine the effectiveness of these strains in promoting wheat growth under salinity stress (125 mM, 150 mM and 200 mM) were carried out. The results revealed that a consortium of two isolates (Serratia sp. and Halomonas sp.) performed best at 125 mM. But, at higher concentrations it was the halophilic bacteria Halomonas sp which gave the best result. In all cases, there was a significant improvement in the growth of wheat seedlings inoculated with the bacteria, compared to non-inoculated controls.

The protection of grapevine from the diseases is now particularly focused on the development of environmentally friendly strategies. Although sulphur is not in itself a toxic substance, a large use towards powdery mildew, in organic vineyards especially, may cause problems to environment, health and safety of viticultural workers and plant phytotoxicity. The activity on powdery mildew of sulphur applied at doses reduced up to 50% in tank mixtures with silicates and Equisetum arvense based products, never tested on grapevine, was assessed. Two-year trials were carried out applying the products every 7-9 days in the period of greatest risk for spring ascosporic infections, in two organic vineyards in the Abruzzo region, Italy. The effectiveness towards the disease of the mixtures was demonstrated, often to a greater extent than that of full-dose sulphur, normally used in the vineyards. Furthermore, in vines treated with the mixtures, increases in yield quantity and quality, such as higher contents of soluble solids and lower levels of total acidity, have been shown. Due to the strong efficacy demonstrated on the leaves, silicon-based products + sulphur mixtures can also be recommended in eradicative applications, aimed at reducing the inoculum of the disease. The great activity of the mixtures demonstrated in this study suggests confirmation through further investigations on different cultivars and vine-growing areas at different levels of infection, also testing the effectiveness of individual silicon products against the disease.

Fire blight, caused by the plant-pathogenic bacterium Erwinia amylovora, is a highly contagious and difficult-to-control disease due to the efficient dissemination, survival, and scarcity of effective control methods. Copper and antibiotics are the most used treatments but pose environmental and human health risks. Bacteriophages (phages) constitute an ecological, safe, and sustainable fire blight control alternative. The goal of this study was to search for specific E. amylovora phages from plant material, soil, and water samples in Mediterranean environments. A collection of phages able to specifically infect and lyse E. amylovora strains was generated from former fire blight-affected orchards in Eastern Spain. Following in vitro characterization, assays on immature fruit revealed that preventively applying some of the phages or their combinations delayed the onset of fire blight symptoms and reduced the disease severity, suggesting their biocontrol potential in Spain and other countries. Morphological and molecular characterization of the selected E. amylovora phages classified them as members of the class Caudoviricetes (former Myoviridae family) and genus Kolesnikvirus. This study reveals Mediterranean settings as plausible sources of E. amylovora-specific bacteriophages, and provides the first effective European phage cocktails in plant material for the development of sustainable fire blight management measures.

The fifth Industrial revolution (I5.0) prioritizes resilience and sustainability, integrating cognitive cyber-physical systems and advanced technologies to enhance machining processes. Numerous research studies have been conducted to optimize machining operations by identifying and reducing the sources of uncertainty and estimating the optimal cutting parameters. Virtual modeling and Tool Condition Monitoring (TCM) methodologies have been developed to assess the cutting states during machining processes. With a precise estimation of cutting states, the safety margin necessary to deal with the uncertainties can be reduced, resulting in improved process productivity. This paper reviews the recent advances in high-performance machining systems with a focus on the cyber-physical models developed for the cutting operation of difficult-to-cut materials using cemented carbide tools. An overview of the literature and background on the advances in the offline and online process optimization approaches have been presented. Process optimization objectives such as tool life utilization, dynamic stability, enhanced productivity, improved machined part quality, and reduced energy consumption and carbon emissions are independently investigated for the offline and online optimization methods. Addressing the critical objectives and constraints prevalent in industrial applications, the paper explores the challenges and opportunities inherent in developing a robust cyber-physical optimization system

In this paper, a class of coupled competitive neural networks, which subject to disturbance and discontinuous activation functions, is concerned. To realize the fixed-time quasi-bipartite synchronization, an aperiodic intermittent controller is initially designed. Subsequently, by combining the fixed-time stability theory and nonsmooth analysis, several criteria are established to ensure the bipartite synchronization in fixed time. Moreover, synchronization error bounds and settling time estimates are provided. Finally, numerical simulations are presented to verify the main results.

This paper explores the intricate world of microbial life, focusing on biofilm as a dynamic consortium of bacteria forming complex networks within a self-produced matrix of extracellular polymeric substances (EPS). Analogous to a bacterial house, these structures provide both shelter and support, playing a pivotal role in the microbial realm with dual effects on human and environmental contexts. Biofilm's significance extends beyond its microcosmic architecture, positively contributing to heavy metal removal, electricity generation through microbial fuel cells, and structural remediation, while also posing threats with detrimental formations implicated in conditions from lung to urinary tract infections. Control of biofilm becomes imperative to unlock its positive attributes and mitigate potential negatives, serving as a cornerstone for environmental remediation, sustainable energy, and infrastructure maintenance. Employing a comprehensive bibliographic approach, this study identifies keywords, countries, and organizations influencing biofilm research, proposing innovative avenues like machine learning for future exploration. The aim is not only to contribute to existing knowledge but to pioneer cutting-edge strategies for biofilm optimization and challenge mitigation, shaping its trajectory towards sustainable applications across diverse fields.

Researchers are always looking to find ways to use energy more efficiently while keeping people comfortable at home. They've tried different methods like fuzzy logic and genetic algorithms to do this. In this paper, we introduce a novel model that combines different techniques like data smoothing, optimization, machine learning, and control algorithms to reach this goal in smart homes. The proposed model is made up of three main parts: smoothing, optimization, and control. The smoothing part uses the Kalman filter to get rid of any unnecessary noise and make sure the data used to predict energy use is clean and smooth. The optimization part uses both genetic with firefly algorithms and artificial neural networks to minimize the gap between the actual environmental conditions and the conditions users find comfortable. It adjusts the comfort settings in real-time using machine learning. The control part uses Mamdani fuzzy logic to make sure energy is delivered in the best way possible to the systems that control temperature, lighting, etc., making the home comfortable and saving energy at the same time. Comparative analyses demonstrate the superiority of the proposed model over existing algorithms, including the Particle Swarm Optimization (PSO) algorithm. Additionally, the paper discusses the importance of adaptive controllers in addressing issues associated with incorrect PID controller selection and highlights the benefits of using the FA-GA in energy optimization and comfort improvement. Overall, the proposed model offers an effective solution for efficient energy consumption optimization and enhanced user comfort in diverse settings through the integration of advanced algorithms and optimization modules.

It is unavoidable that the characteristics of the robot system alter inexactly or cannot be correctly determined during movement and are impacted by external disturbances. There are many adaptive control methods, such as sliding control or neural control, to improve the quality of trajectory tracking for robot motion systems. Still, those methods require a large amount of computation related to solving the problem of constrained nonlinear optimization problem. The article presents some techniques for determining an intelligent controller's online learning function parameters, including two circuits: the inner circuit is a state feedback linearized controller, and the outer course is an Interactive learning controller and does not use the robot's mathematical mode with function parameters online optimal learning and intelligent online learning closely following the joint model to stabilize the robot system. Finally, the 2-DOF planar robot simulation is performed on Matlab software R2022b. The findings indicate that outstanding tracking performance is achievable.

In Active Flow Control (AFC) applications, to activate the boundary layer the use of pulsating flow has notorious energy advantages versus constant blowing/suction jet injections. For a given AFC application, five parameters, jet location and width, inclination angle, frequency of injection and momentum coefficient need to be tuned. Two main devices are nowadays capable of injecting pulsating flow with the sufficient momentum coefficient to delay the boundary layer separation, these are the Zero Net Mass Flow actuators (ZNMFA) and the Fluidic Oscillators (FO). In the present research, a novel FO configuration is analyzed for the first time at relatively high Reynolds numbers, fluid is considered as incompressible. After obtaining the typical linear correlation between the incoming Reynolds number and the outlet flow oscillating frequency, the effect of outlet width and mixing chamber wedge inclination angle dimensional modifications is addressed, modifications of the outlet width are observed to create large variations on the FO performance. The origin of the self-sustained oscillations is also analyzed in the present manuscript and greatly helps in clarifying the forces acting on the jet inside the mixing chamber. In fact we can conclude saying that the current FO configuration is pressure driven although the mass flow forces appear to be a much more relevant than in previous FO configurations studied.

This study introduces a cybernetic control and architectural framework for a robotic fish avatar operated by a human. The behavior of the robot fish is influenced by the electromyographic (EMG) signals of the human operator, triggered by stimuli from the surrounding objects and scenery. An deep artificial neural network (ANN) with perceptrons classifies EMG signals, discerning the type of muscular stimuli generated. The research unveils a fuzzy-based oscillation patterns generator (OPG) designed to emulate functions akin to a neural central pattern generator, producing coordinated fish undulations. The OPG generates swimming behavior as an oscillation function, decoupled into coordinated step signals, right and left, for a dual electromagnetic oscillator in the fish propulsion system. Furthermore, the research presents an underactuated biorobotic mechanism of the subcarangiform type, comprising a two-solenoid electromagnetic oscillator, an antagonistic musculoskeletal elastic system of tendons, and a multi-link caudal spine composed of helical springs. The biomechanics dynamic model and control for swimming, as well as the ballasting system for submersion and buoyancy, are deduced. Experimental results encompass EMG pattern recognition, OPG, and coordinated fish locomotion, with additional topics illustrated through numerical simulations.

Experimental investigations were conducted to uncover the impact of cavitation control - through the use of riblets (mesoscale surface structuring) - on cavitating flows around a circular cylinder. First, the dynamics of cavitation in the flow behind a finite cylinder (without riblets) was unveiled by visualizing the cavitation clouds and measuring the lift force fluctuations acting on the cylinder. Second, as a significant step forward, a comprehensive explanation was provided for the mechanism of cavitation control using two bio-inspired riblet morphologies positioned in different orientations and locations on the cylinder. For the first time, the effects of these tiny structures on the flow dynamics and the associated cavitation process were scrutinized. This showed that scalloped riblets, with their curved design, induced secondary vortices near their tips and distorted primary streamwise vortices, and that high velocity gradients near the jagged pattern peaks of sawtooth riblets delayed flow separation, which affected cavitation.

Fire blight, caused by Erwinia amylovora, is a devastating bacterial disease that threatens world-wide production of apples and pears. In Canada and the US, streptomycin and kasugamycin are commonly used for the control of this pathogen. There is an urgent need for development of biocontrol agents (BCAs) that can be easily incorporated into integrated pest management pro-grams with high efficacy against streptomycin sensitive and resistant strains of E. amylovora. In addition, excessive use of antibiotics in agriculture has increased awareness of the possibility of antibiotic resistance gene transfer to human, animal and environmental microbes. To address this issue, a phage-carrier system (PCS) that combines Pantoea agglomerans as an antagonistic bacterial carrier of Erwinia phages as a double-pronged treatment for fire blight have been de-veloped. The low viability of P. agglomerans cells following spray drying challenged the industrial scale production of this PCS. In the present research, a spray drying protocol was developed for P. agglomerans by modifying the growth medium and the bacterial cell formulation using D(+)-trehalose and maltodextrin. The developed protocol is amenable to industrial scale pro-duction of the BCA/PCS. The P. agglomerans viability was greater than 90% after spray drying, had a prolonged shelf life of 4 months at 4 C, and the reconstituted cells showed an approximate 3 log reduction in E. amylovora counts with a green pear disc challenge assay.

The Attentional Control Theory (ACT) suggests that trait anxiety does not directly affect performance but may alter processing efficiency through the generation of compensatory strategies. However, the ACT does not describe the nature of these strategies, which could be reflective in nature. One hundred ten students (M = 20.12; SD = 2.10) completed questionnaires on trait anxiety, metacognitive beliefs, and emotion regulation strategies (ERS). They performed two working memory tasks: the digit span task from the WAIS-IV and an emotional n-back task. Anxiety, metacognitive beliefs, and maladaptive ERS were not linked to performance but were associated with longer response times. Additionally, participants using maladaptive ERS, such catastrophizing and rumination, made fewer negative commission errors and employed more strategies during the digit span. These findings support the role of the reflective level in influencing trait anxiety's impact on performance and emphasize considering metacognitive beliefs and maladaptive ERS for a comprehensive understanding of the ACT. Identifying these variables provides insights to optimize cognitive abilities and promote academic success.

Inverse optimal control is a method for recovering the cost function used in an optimal control problem in expert demonstrations. Most studies on inverse optimal control have focused on building the unknown cost function through the linear combination of given features with unknown cost weights, which are generally considered to be constant. However, in many real-world applications, the cost weights may vary over time. In this study, we propose an adaptive online inverse optimal control approach based on a neural-network approximation to address the challenge of recovering time-varying cost weights. We conduct a well-posedness analysis of the problem and suggest a condition for the adaptive goal, under which the weights of the neural network generated to achieve this adaptive goal are unique to the corresponding inverse optimal control problem. Furthermore, we propose an updating law for the weights of the neural network to ensure the stability of the convergence of the solutions. Finally, simulation results for an example linear system are presented to demonstrate the effectiveness of the proposed strategy. The proposed method is applicable to a wide range of problems requiring real-time inverse optimal control calculations

In this paper, a buck DC-DC converter with the proposed twin frequency control scheme (TFCS) and accurate load current sensing (ALCS) have been designed and implemented with 0.18µm CMOS technology for a supply voltage ranging from 2.0-3.0V which is compatible with state-of-the-art batteries (NiCd/NiMH: 1.1-2V, Li-Ion: 2.5-4.2V). The proposed converter yields a peak efficiency of about 92.7% with a load current of 30mA. Furthermore, it only occupies a silicon area of 1.3mm2. The proposed buck converter is dedicated for smartphone applications whereby it spends most of its time in idle, low load conditions.

This paper addresses a mode-dependent state-feedback H∞ control for descriptor hybrid systems, considering both the absence and presence of actuator saturation. Firstly, the necessary and sufficient conditions for the stochastic admissibility criterion with H∞ performance ? of the closed-loop system is proposed. Given the proposed non-convex condition, the author reformulates it into linear matrix inequalities (LMIs). Then, to extend the result to the systems with actuator saturation, the actuator saturated control input is expressed as a linear combination of given state-feedback control input and a virtual control input that remains under the saturation level. To verify this expression, the set invariant condition is also suggested by using the singular mode-dependent Lyapunov function candidate. Therefore, the LMI conditions for the existence of the mode-dependent state-feedback H∞ control and the ellipsoidal shape of invariant set are successfully derived. Two numerical examples demonstrate the effectiveness of the proposed approach in optimizing H∞ performance $\gamma$ and identifying the largest invariant set.

Enhancing traffic safety is one of the fundamental objectives of Intelligent Transport Systems (ITS), and it aligns closely with the principles of sustainable transport. Due to specific differences in infrastructure, vehicles, and users’ behaviour, places where different modes of traffic intersect are recognized as critical points of the traffic system, making them crucial aspects of Sustainable Urban Mobility Plans (SUMPs) implementation. The SUMPs aim to create urban mobility that is not only environmentally friendly and efficient but also safe for all users. The continuous development and widespread adoption of innovative ITS technologies have paved the way for a system that could provide drivers with real-time information about both immediate and potential dangers at these critical points. This paper provides an overview of previous research in the field, investigating the impact of information systems on drivers’ behaviour, various detection and communication solutions that can be effectively integrated into such a system, as well as a brief overview of models and solutions that have been developed to warn drivers in a similar context. The reviewed literature offered valuable insights on which a novel driver information system architecture framework is proposed. This framework can contribute to the ongoing safety improvement in multimodal transport networks within the context of sustainable transport.

Efficient traffic systems control in large cities with complex traffic management of signalized intersections is a challenging task, particularly when dealing with high traffic volumes. The city of Zagreb faces this challenge, as all administrative and governmental institutions are located in the old city centre, and routes for escorted vehicles have a significant impact on the traffic network. This paper addresses the issue of the impact of unconditional priority for escorted vehicles on the energy efficiency of the urban traffic network in the city of Zagreb. The traffic network model is developed by using the PTV Vissim microsimulation software. The evaluation was conducted with node (delay, queue length, number of stops) and network evaluation parameters (CO2 emission, NOx emission, PM10 emission, and fuel consumption). The results show that unconditional priority has minimal impact on energy consumption and exhaust emission in the observed scenario. This is a significant result considering all actions that have to be done to manage the passage of the escorted vehicles through the traffic network.

Acid in-situ leaching (ISL) is a common approach to the recovery of uranium in the subsurface. As some toxic and harmful substances might be produced by the chemical reactions among the injected sulphuric acid, the groundwater, and the porous media during leaching processes, the pollution control of the mining plan for ISL is important. In this study, a three-dimensional reactive transport modeling (3DRTM) was applied to decide the pollution control mining plan, considering the partial penetration through wellbore in confined aquifer and complex chemical reactions between main minerals. Based on the 3DRTM, different pumping ratio and non-uniform injection schemes were compared. The results show that the preferential pollution control mining plan is non-uniform injection ratio equal 0.1. By analyzing the characteristics of water table and streamline, it is concluded that the scheme has a strong hydraulic capture effect. In this scheme, the concentration of UO22+, H+, SO42- obtained by 3DRTM is lower. The inner well injection rate is 194.09 m3/d, the outer well injection rate is 158.89 m3/d, and the pumping rate is 264.00 m3/d. A reasonable suggestion is to adopt non-uniform injection mining mode in ISL.

In this paper, an adaptive technology and the interconnection and damping assignment passivity-based control method are combined to solve the stabilization problem for underactuated mechanical systems with uncertainties (including matched and unmatched). Uncertainties include unknown friction coefficients and unknown terms in kinetic energy and potential energy. A novel adaptive interconnection and damping assignment passivity-based control scheme is proposed and an adaptive stabilization controller is designed to make the closed-loop system locally stable. Verification is conducted on the ball and beam system, taking into account uncertainties of friction coefficients, kinetic energy, and potential energy. The locally asymptotic stability is demonstrated using the LaSalle’s invariance principle and approximate linearization. The effectiveness of the proposed control law is verified through numerical simulations.

Diabetes mellitus (DM) is a metabolic disease characterized by chronic hyperglycemia associated with impaired carbohydrate, lipid and protein metabolism, with concomitant absence of insulin secretion or reduced sensitivity to its metabolic effects. Patients with diabetes mellitus have 30% more risk of developing heart failure and cardiovascular disease with respect to healthy people. Heart and cardiovascular problems are the first cause of death worldwide and the main complications which lead to high healthcare costs. Such complications can be delayed or avoided by taking prescribed medications in conjunction with a healthy lifestyle (i.e. diet and physical activity). The American College of Sports Medicine and the American Diabetes Association recommend that diabetic people reduce total sedentary time by incorporating physical activity in their weekly routine. This narrative literature review has the aim to summarize and present the main guidelines, pre-exercise cardiovascular screening recommendations, and considerations for patients with diabetes and comorbidities who are planning to participate in regular exercise regimens.

Compared with ordinary asphalt pavement, the application of modified asphalt will improve the performance of asphalt pavement. However, using the same modification method for the whole road section can cause modification waste or result in some parts not meeting performance standards. This paper proposes a whole road section modification method. First of all, a finite element model was established using Abqus according to the actual road pavement material to analyze the mechanical response of each layer under different working conditions and establish the grading standard under comprehensive working conditions. Secondly, different modification methods were analyzed according to investigation and their modification effects were graded through clustering analysis method. Finally, different working conditions and different modification methods were reasonably matched and a section of highway was selected for verification. The results show that before modification, the calculated rutting is 6.23mm and after modification, it is reduced to 2.45mm which indicates that reasonable modification has a better effect and can achieve the purpose of rutting equalization control on the whole road section. It is of great significance to carry out reasonable modification on different conditions to control rutting equalization of asphalt pavements.

This work investigates the sliding mode control (SMC) problem for a class of uncertain switched systems subject to asynchronous switching and an assigned finite time constraint. Two important issues are how to ensure the reachability of state trajectories within the assigned time and the input-to-output finite-time stability (IO-FTS) of the closed-loop switched systems during the whole phase under asynchronous switching. To achieve these objectives, an asynchronous sliding mode controller with adjustable parameters is constructed to drive the state trajectories onto the sliding surface during the assigned finite-time interval. By means of the partitioning strategy, sufficient conditions for the IO-FTS of the closed-loop switched are derived during the whole phase [0,T] using the multiple Lyapunov function (MLF) approach. Additionally, the asynchronous characteristics are detailedly investigated while analyzing the reachability of a specified sliding surface. Finally, an illustrative example is given to illustrate the effectiveness of the proposed method.

A class of controlled plants, whose dynamics is governed by a vector system of ordinary differential equations with a partially known right-hand side, is considered. The state variables and their velocities are assumed to be measurable. The aim is to design a controller which minimizes a loss function under certain constraints which arguments is the current state of the controlled plant. The designed control action is admitted to be a function of the current sub-gradient only, which supposed to be measurable on-line. The control design is based on ASG (Average Sub-Gradient method) — version of Integral Sliding Mode (ISM) concept, aimed to minimize on average a given convex (not obligatory strongly convex) cost function of the current state under a set of given constraints. An optimization type algorithm is developed and analyzed using ideas of SDM technique. The main results consist in proving the reachability of the "desired regime" (nonstationary analogue of sliding surface) from the beginning of the process and obtaining an explicit upper bound for the averaged loss function decrement, that is, the averaged in time functional convergence is proven and the rate of such convergence is estimated.

Mild cognitive impairment (MCI) is when brain function declines. It is a transition stage between normal aging and Alzheimer's disease (AD) and may be an underlying symptom of AD. Improper use of test instruments or imperfect test methods in clinical practice often leads to variations in test results. In addition, there may be resistance from the subject if he/she has to undergo multiple screening tests simultaneously. Therefore, the objective of this study was to use virtual reality to create an image testing scenario that integrates Mini-Cog, Short Portable Mental Status Questionnaire (SPMSQ), Mini-mental Status Examination (MMSE), Saint Louis University Mental Status Examination (SLUMS), Clinical Dementia Rating (CDR), and Cognitive Abilities Screening Instrument (CASI), and combine fuzzy logic control (FLC) technology to develop an MCI forecasting system. There were 24 middle-aged to older adults aged 50 to 65 years who participated in the evaluation experiment. The results showed that the MCI forecasting system developed in this study is highly correlated with the traditional screening tests, including Mini-Cog, SPMSQ, MMSE, SLUMS, and CASI. The forecasting system can provide an integrated reference score for testers in making judgments. In addition, the distribution of the System Usability Scale (SUS) evaluation scores for the MCI forecasting system revealed that 87.5% were grade C (good to use) or above, and 29.2% were grade B (extremely good to use) or above. The forecasting system receives positive feedback from the subjects.

Food safety and quality are the first steps in the food chain. This work reports a low-cost and easy-to-use optoelectronic measurement system for improving feed chain quality and safety, based on near-infrared spectrometry (NIRS) technology. This is a significant challenge for dairy farm technicians and producers who need rapid and reliable knowledge of forage quality on their farms. In most cases, instrumentation suitable for these specifications is expensive and difficult to operate. The core of the measurement system is Texas Instruments´ NIRscan Nano Evaluation Module (EVM) spectrometer. This module has a large sensing area and high resolution suitable for forage samples. To evaluate the feasibility of the prototype to analyze agrifood samples, different ways of presenting the sample, intact or ground, were tested. The final objective of the research is not just to check the efficiency of the proposed system. It is also to determine the measurement system characteristics and how to improve them.

Let G be a connected Lie group with Lie algebra g. This review is devoted to studying the fundamental dynamic properties of elements in the normalizer NG of G. Through an algebraic characterization of NG we analyze the different dynamics inside the normalizer. NG contains the well-known left-invariant vector fields and the linear and affine vector fields on G. In any case, we show the shape of the solutions of these ordinary differential equations on G. We give examples in low-dimensional Lie groups. It is worth saying that these dynamics generate the linear and bilinear control systems on Euclidean spaces and the invariant and linear control systems on Lie groups. Moreover, the Jouan Equivalence Theorem shows how to extend this theory to control systems on manifolds.

Most petrochemical plants still maintain a Proportional-Integral-Differential controller(PID) system, which is a feedback control system. However, gradually, the PID system is being extended and introduced to the Advanced Process Controller (APC) system, which is an integrated control system of feedforward and feedback that predicts external influences in advance. In the process of conducting on-site plant tests and calculating APC model parameter for the application of APC systems, a problem arises that Model Parameter are implemented differently depending on the proficiency of APC engineers. To minimize this problem, a technique for estimating APC model parameter without a plant test is required. In order to estimate the APC model parameter, it is necessary to train on dynamic interval data. In this paper, we use statistical techniques such as PELT, Linear Kernel, and Radial Basis Function Kernel of Change Point Detection (CPD) to extract dynamic data with minimum Mean Absolute Error (MAE) from time series data of a real petrochemical plant. Then, the hyper parameter is fixed and the APC model parameter is estimated by learning the dynamic section data. By applying the estimated APC model parameter to the APC Model Tool and measuring the fitting rate, it was confirmed that it is possible to estimate the APC model parameter with excellent control performance without plant test.

In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

Intersections within urban centers do not allow all citizens to move in a fluid manner. In this sense, this paper proposes a queuing network model based on Kendall's notation for the intersection of two urban streets (East 53rd Street and East 56th Street) in Panama City. A set of traffic lights operating under a fixed time scheme controls the vehicular flow at the intersection. The objective is to optimize the vehicular flow at the intersection by minimizing the waiting time of the vehicles using mathematical models, Linear Regressor Model, and simulations performed in MATLAB evaluating the waiting time experienced by the vehicles. Based on the results obtained, the optimal signal timing of the traffic lights is determined to minimize the waiting time for both streets.

In order to enable patients with severe disabilities who have lost their limbs to accurately control their wheelchair movement and optimize the power loss of smart wearable tongue control devices, a non-invasive intraoral stand-alone tongue control system based on RSIC-V edge computing is proposed in this paper. Patients can detect the pressure signal of the tongue muscles’ touching the palate by placing the flexible carbon nanotube-PDMS pressure sensor array in the mouth, and the erroneous movement signal can be avoided by setting the pressure threshold, thereby improving the reliability of the device and the user's experience. The system converts the pressure data into specific control instructions on the edge of the RSIC-V chip and transmits them to the receiver, thus reducing the transmission of data. In this experiment, the speed response time test, the center click task and the power consumption experiment are carried out, whose results show that the adaptive fuzzy PID control algorithm has good robustness in the system: when the DC motor with a given speed of 750r/min reaches the steady state, its rise time is 0.108s and the adjustment time is 0.59s. The dynamic power consumption of the non-intrusive intraoral stand-alone tongue control system proposed in this paper is tested to be 3.745 MW, which is 11.5% lower than the total power consumption of the sTDs system.

Ants of the genus Solenopsis are important invasive pests in the world. Due to their high dispersion capacity, aggressive behavior and because they feed on various sources of vegetable and animal protein, these insects have caused serious damage to public health and agriculture. The control has usually been carried out through the use of organosynthetic insecticides. However, due to the ecological and environmental impacts caused by the use these products, more sustainable alternatives have been sought for their control. Faced with these problems and due to the scarcity of registered products for the control of these insects, we aimed with this study to synthesize and evaluate the anticidal potential of carvacrol derivatives. The lethal and sublethal effects caused by these derivatives were compared with the essential oil of Lippia gracilis (50.7% carvacrol) and with the base molecule — carvacrol. Carvacryl benzoate was the most toxic derivative to Solenopsis sp. with an LD50 of 3.20 g/ mg. This compound was about 2 and 7.6 times, more toxic than carvacrol at the doses needed to kill 50 and 90% of populations, respectively. The workers of Solenopsis sp. showed a rapid reduction in survival when exposed to carvacrol (LT50 = 8.43h) and carvacryl benzoate (LT50 = 8.87h). Insects treated with sublethal doses of the compounds did not show significant effects on self-cleaning, allogrooming and aggregation, with the exception of those treated with L. gracilis essential oil. The oil increased self-cleaning and reduced allogrooming and aggregation. Ants treated with carvacrol and carvacryl benzoate showed greater distance and speed when compared to the control. These compounds decreased meanders and angular velocity. When live workers were exposed to dead individuals at the LD90 of the compounds, carvacryl benzoate was the derivative that most reduced insects survival, due to horizontal transfer. These results show the potential of the carvacrol derivative — carvacryl benzoate — for the alternative management of ants of the genus Solenopsis sp.

Effortful control (EC) describes individual differences in self-regulation, with a strong attentional basis. Moreover, during early childhood EC has a central role on children’s socio-emotional adjustment and academic achievement. The aim of the current study was to predict the development of EC at 36 months of age from early attentional and environmental measures taken in infancy using a machine learning approach. A sample of 75 infants participated in a longitudinal study running different waves of data collection at 6, 9 and 36 months of age. Attentional tasks were administered at 6 months of age and two additional measures were collected at 9 months of age. Parents reported household environment variables during wave 1, and their child’s EC at 36 months. A machine -learning algorithm was implemented to identify children with low EC scores at 36 months of age. An “attention only” model showed greater predictive sensitivity than the “environmental only” model. However, a model including both attentional and environmental variables was able to classify the groups (Low-EC vs Average-to-High EC) with 100% accuracy. Sensitivity analyses indicate that socio-economic variables together with attention control processes at 6-months, and self-restraint capacity at 9-months, are the most important predictors of EC. Results suggest a foundational role of executive attention processes in the development of EC in complex interaction with household environment and provide a new tool to identify early markers of socio-emotional regulation development.

The Yellow-legged Hornet (Vespa velutina nigrithorax) (YLH) is an invasive insect that arrived in Europe in 2004 and is now spread across nine countries. It is a threat to the native entomofauna and harmful to beekeeping and agriculture, as it is a ravenous predator of the European Honey Bee (Apis mellifera) and other pollinating species. Its expansion has been unstoppable and all resources are needed to fight against it, including native vertebrate predators. Among these, the European Bee-eater (Merops apiaster) (EBE) is a potential one, but little is known about its predation on YLH. In a study carried out in Portugal, remains of YHL were detected in EBE nesting sites, which to the best of our knowledge is the first such report. This means that this bird could be one more agent in the biological control of this pest (although research on predation intensity is still needed), in conjunction with other natural predators and other strategies. In the Iberian Peninsula both species are allopatric in vast regions, so the role of EBE may be more limited. However, in the rest of Europe, at a country or continent scale, the scenario may be different and sympatry may occur to a greater extent.

: Efficient or at least rational use of energy resources is a problem that occupies an overwhelming number of people in modern society – from major scientists and politicians to journalists and schoolchildren who have a poor understanding of the basic laws of physics.(the knowledge of politicians in this area is also sometimes doubtful). At the same time, the main focus of the discussions is on the resource base, possible waste and consequences. According to these features, they want to see the future of energy. However, the division of "energetik" follows different principles. On the one hand, these are thermal, nuclear and hydropower sources. On the other – wind and solar energy. Obviously, this separation is not only related to the renewable resources or the absence of consequences for the environment and humans. If we do not touch on geopolitical problems. which are not the subject of this article, it is obvious that the main dividing feature of these types of energy production will be their controllability. The theory of automatic control (TAU) is one of the most complex modern sciences that has been developing for many years to solve precisely the problems of energy Now, when considering energy problems, this science is most often not remembered. Maybe because the most active participants in the discussions don't know much about it? Or is this situation beneficial to someone? How efficiency and controllability are related to some problems with controllability in the "household" energy sector, which concerns almost every inhabitant of the planet and in the global energy sector, this article is devoted to

Load Frequency Control (LFC) is essential to ensure the stability and performance of power systems. In this study, a novel optimization algorithm, the Sea Horse Optimizer (SHO) algorithm, was proposed for optimizing controller parameters in LFC problems of power system. The proposed SHO algorithm was tested on a two-area power system with photovoltaic system and reheat thermal units, under three different scenarios: a 10% load change in both area, large load disturbances, and varying solar radiation. The proposed algorithm optimizes the gain parameters of PI/PID controllers using performance metrics such as Integral of Absolute value of the Error (IAE), Integral of Square Error (ISE), Integral of Time multiplied by Square Error (ITSE), and Integral of Time multiplied by Absolute Error (ITAE). The study compared the performance of the SHO-optimized controller with other reported optimization algorithms such as Genetic Algorithm (GA), Firefly Algorithm (FA), Whale Optimization Algorithm (WOA), and Modified Whale Optimization Algorithm (MWOA). The study also evaluated the accuracy and effectiveness of the controllers using performance metrics such as Settling Time, Overshoot (M+), and Undershoot (M-). The results show that the SHO-tuned controller significantly reduces overshoot, undershoot, and settling time of the system oscillations compared to other algorithms. The study provides valuable insights into the optimization of LFC controllers and presents a significant contribution to the literature with its novel algorithm. The proposed SHO algorithm can be considered an effective alternative solution method for LFC in power systems.

This paper gives solutions to puzzles of double Wheeler’s delayed choice experiments, a photon’s passing two paths simultaneously and wave collapse velocity measure, and shows new quantum control, new quantum oscillation and new controlling photon oscillator (that can be arranged in quantum computer and quantum network as their classical correspondences) in experiments. Furthermore, this paper obtains the measured attractive state and the new useful key technology of altering state’s evolving paths for quantum systems. We discover the reason and the technological way for the present changes the past, further show their feasible experiments of new quantum control, new quantum oscillation and new quantum oscillator. Finally, this paper achieves the collapse response time t of wave, further concretely deduces the measured collapse velocity of quantum system. In the past, the collapse velocity cannot be objectively deduced and experimentally measured.

Although there are several access control systems in the literature for flexible policy management in multi-authority and multi-domain environments, achieving interoperability &amp; scalability, without relying on strong trust assumptions, is still an open challenge. We present HMBAC, a distributed fine-grained access control model for shared and dynamic multi-authority and multi-domain environments, along with Janus, a practical system for HMBAC policy enforcement. The proposed HMBAC model supports: (a) dynamic trust management between different authorities; (b) flexible access control policy enforcement, defined at domain and cross-domain level; (c) a global source of truth for all entities, supported by an immutable, audit-friendly mechanism. Janus implements the HMBAC model and relies on the effective fusion of two core components. First, a Hierarchical Multi-Blockchain architecture that acts as a single access point that cannot be bypassed by users or authorities. Second, a Multi-Authority Attribute Based Encryption protocol that supports flexible shared multi-owner encryption, where attribute keys from different authorities are combined to decrypt data distributedly stored in different authorities. Our approach was implemented using Hyperledger Fabric as the underlying blockchain, with the system components placed in Kubernetes Docker container pods. We experimentally validated the effectiveness and efficiency of Janus, while fully reproducible artifacts of both our implementation and our measurements are provided.

The alteration of natural land cover to impervious surfaces during development increases stormwater runoff. Stormwater Control Measures (SCMs) are used to manage water quantity and enhance water quality by restoring the hydrologic cycle altered by development. Often, SCMs have an outflow pipe to handle overflows or to manage the release of water detained when infiltration is not possible. Traditionally, these are static controls (e.g. a small orifice is used to restrict the volume of outflow), however, these systems can be improved by instituting real-time controls (RTC). RTC improve the functionality of SCMs by dynamically controlling outflows to adjust to environmental conditions. A major impediment to the widespread implementation of RTC is the high cost of installation and operation. This study utilized machine learning methods to develop a forecasting approach for the implementation of low-cost RTC that were implemented on a programmable gate of the outlet structure of a multi-stage basin in southeastern Pennsylvania. The goals were to decrease the peak flow exiting the basin during rain events, increase the volume of water detained, decrease the number of overtopping events, maintain healthy vegetation in the basin, and protect the downstream vegetation from erosion. Multiple popular data science algorithms were evaluated including multiple linear regression and long short-term memory. These algorithms were used with a dataset, which consisted of four years of historical sensor data, collected in 5-minute intervals, to train models to predict water levels to optimize operations. The accuracy of 30 models with three different methods of handling missing values were compared. A long short-term memory model configured with a 30-minute lead time produced the best results. Having an approximate same lag time of 30 minutes for the contributing drainage area of the SCM provided a sufficient RTC functioning period to improve the performance of the outlet structure.

Nowadays, diamonds are widely used in science and technology. However, the properties of diamonds due to their defects are not fully understood. In addition to optical methods, positron annihilation spectroscopy (PAS) can be successfully used to study defects in diamonds. Positrons are capable of detecting vacancies, small and large clusters of vacancies induced by irradiation, by providing information about their size, concentration, and chemical environment. By mapping in the infrared (IR) range, it is possible to consider the admixture composition of the main inclusions of the whole plate. The article presents the results of the study of defects in synthetic diamond plates, one of which was irradiated by electrons. Presents data about the distribution of the defect concentration obtained by Infrared spectroscopy. PAS with a monochromatic positron beam can be used as a non-destructive technique of detecting defects (vacancy) distribution over the depth of diamond plates.

Reasonable trajectory planning is the precondition for the parafoil airdrop system to achieve autonomous accurate homing and safe landing. In order to successfully realize the self-homing of the parafoil airdrop system, a new trajectory optimization design scheme is proposed in this paper. The scheme is based on the parafoil's unique flight and control characteristics and adopts a segmented homing design. Compared with the current common trajectory design method, its core feature is to avoid the problem that the straight-line flight distance before landing is limited by the radius of the height-reducing area and ensure landing accuracy and safety. Firstly, the different starting states of the parafoil airdrop system and the landing requirements were comprehensively considered, and the homing trajectory is reasonably segmented. Based on the requirements of energy control, stable flight, and landing accuracy, the optimal objective function of the trajectory was established, and the trajectory parameters, calculation methods, and constraints were given. Secondly, the cuckoo search algorithm was applied to optimize the objective function to obtain the final home trajectory. Finally, the trajectory planning under different airdrop conditions was simulated and verified. The results showed that the planned trajectories could reach the target point accurately and meet the flight direction requirements, proving the proposed scheme's correctness and feasibility.

Recurrent hypoglycaemia, a common side-effect of insulin therapy in the treatment of type 1 diabetes, induces impaired glucose-sensing. Better understanding of how astrocytes, important non-neuronal cells in the brain, function in low glucose environments may improve our understanding of recurrent hypoglycaemia-induced defective counterregulation. Astrocytes contribute to glutamatergic signalling, which is required for hypoglycaemia counterregulation and is impaired by recurrent insulin-induced hypoglcyaemia. This study examined the glutamate response of astrocytes when challenged with acute and recurrent low glucose (RLG) exposure. The metabolic responses of cortical (CRTAS) and hypothalamic (HTAS) primary rat astrocytes were measured in acute and recurrent low glucose using extracellular flux analyses. RLG caused mitochondrial adaptations in both HTAS and CRTAS, many of which were attenuated by glutamate exposure during low glucose treatments. We observed an increase in capacity of HTAS to metabolise glutamine after RLG exposure. Demonstrating astrocytic heterogeneity in the response to LG, CRTAS increased cellular acidification, a marker of glycolysis in LG, whereas this decreased in HTAS. The directional change in intracellular Ca2+ levels of each cell type, correlated with the change in extracellular acidification rate (ECAR) during LG. Further examination of glutamate-induced Ca2+ responses in low glucose treated CRTAS and HTAS identified sub-populations of glucose-excited- and glucose-inhibited-like cells with differing responses to glutamate. Lastly, release of the gliotransmitter ATP by HTAS was elevated by RLG, both with and without concurrent glutamate exposure. Therefore, hypothalamic astrocytes adapt to RLG by increasing glutamate uptake and oxidation in a manner that attenuates RLG-induced mitochondrial adaptations.

In this paper, we propose an efficient numerical computation method of reduced-order controller design for linear time-invariant systems. The design problem is described by linear matrix inequalities (LMIs) with a rank constraint on a structured matrix, due to which the problem is NP-hard. Instead of the heuristic method that approximates the matrix rank by the nuclear norm, we propose a numerical projection onto the rank-constrained set based on the alternating direction method of multipliers (ADMM). Then the controller is obtained by alternating projection between the rank-constrained set and the LMI set. We show the effectiveness of the proposed method compared with existing heuristic methods, by using 95 benchmark models from the COMPLeib library.

Abstract. This article proposes new fuzzy controller to regulation the voltage, damp the oscillations and limit the overshoot behavior in single-machine infinite-bus power system. Two different independent MISO fuzzy controllers are designed. First controller, is voltage stabilizer and it composes of two adaptive fuzzy modules and proportional gain AVR. The voltage stabilizer is designed to regulate the terminal voltage, damp the voltage oscillation and limit the voltage overshoot to the industrial maximum allowable limit. The input signals of this stabilizer is are taken from the terminal voltage and the imposed voltage disturbance that can be read from any smart relay. The fuzzy output is used as feedback signal to control the AVR in order to achieve stabilized voltage equal to the reference voltage. The second fuzzy controller is designed with two input signals; “mechanical angle” and its derivative, and one output which is used as feedback signal to adapt the damping torque in order to damp the mechanical oscillation fast and with maximum overshoot not exceeding 10%, and hence damp the power angle oscillation that is important in the PSS improvement. MATLAB-SIMULINK was used for modelling and the test cases simulation. The results show very good performance for the proposed fuzzy controllers.

Ralstonia solanacearum is the causative agent of bacterial wilt, one of the most destructive plant diseases. While chemical control has an environmental impact, biological control strategies can allow sustainable agrosystems. Three lytic bacteriophages (phages) of R. solanacearum with biocontrol capacity in environmental water and plant were isolated from river water in Europe but not fully characterized, their genomic characterization being fundamental to understand their biology. In this work, the phage genomes were sequenced and subjected to bioinformatic analysis. The morphology was also observed by electron microscopy. Phylogenetic analyses were performed with a selection of phages able to infect R. solanacearum and the closely related phytopathogenic species R. pseudosolanacearum. The results indicated that the genomes of vRsoP-WF2, vRsoP-WM2 and vRsoP-WR2 range from 40,688 to 41,158 bp with almost 59% GC-contents, 52 ORFs in vRsoP-WF2 and vRsoP-WM2, and 53 in vRsoP-WR2 but, with only 22 or 23 predicted proteins with functional homologs in databases. Among them, two lysins and one exopolysaccharide (EPS) depolymerase, this type of depolymerase being identified in R. solanacearum phages for the first time. These three European phages belong to the same novel species within the Gyeongsanvirus, Autographiviridae family (formerly Podoviridae). These genomic data will contribute to a better understanding of the abilities of these phages to damage host cells and, consequently, to an improvement in the biological control of R. solanacearum.

This paper investigates the path following control problem for a unmanned surface vehicle (USV) in the presence of unknown disturbances and system uncertainties. The simulation study combines two different types of sliding mode surface based control approaches due to its precise tracking and robustness against disturbances and uncertainty. Firstly, an adaptive linear sliding mode surface algorithm is applied, to keep the yaw error within the desired boundaries and then an adaptive integral non-linear sliding mode surface is explored to keep an account of the sliding mode condition. Additionally, a method to reconfigure the input parameters in order to keep settling time, yaw rate restriction and desired precision within boundary conditions is presented. The main strengths of proposed approach is simplicity, robustness with respect to external disturbances and high adaptability to static and dynamics reference courses without the need of parameter reconfiguration.

Based on the satellite attitude control method, this paper proposes an attitude control method based on neural network disturbance compensation. The paper firstly analyzes the neural network algorithm and proposes an orthogonal least squares algorithm to implement network learning. In this paper, a set of high-precision directional neural network compensation controllers is designed for the attitude control of acupuncture small satellites. The feasibility of the improved orthogonal least-squared algorithm combined with the neural network supplementary control method in satellite attitude control is verified by experiments.

Hospital-acquired infections (HAIs) contribute to increased length of hospital stay, high mortality and higher health-care costs. Prevention and control of HAIs is a critical public health concern. We conducted a cross-sectional survey of 213 hospital health-care workers in Qassim, Saudi Arabia. We assessed Knowledge, Attitude and Practice (KAP) of standard infection control precautions using a structured questionnaire. Predictors of KAP were investigated using multivaraible logistic regression analyses and independent sample t tests. Prevalence of good (≥80% correct response) knowledge, attitude and practice were 67.6%, 61.5% and 73.2%, respectively. Predictors of good knowledge included age over 34 years (adjusted odds ratio: 30.5, p<0.001), and receiving training (13.3, p<0.001). Predictor of positive attitude was having >6 years of experience (5.5, p<0.001). While, the predictors of good practice were having >6 years of experience (2.9, p<0.01), previous exposure to HAIs (2.5, p<0.05) and training (3.5, p<0.01). However, being female (0.22, p<0.001) and older (>34 years) (0.34, p<0.01) were negatively associated with knowledge. Results indicate that older academic programs might not have adequately covered infection crontrol. Arranging training for HCWs might be useful in improving their knowledge of standard infection control precautions and is also expected to facilitate positive attitude and practice.

Apple replant disease (ARD) is a severe problem in orchards and tree nurseries caused by yet unknown soil biota that accumulate over replanting cycles. This study tested the contribution of nematodes to ARD, and cultivation of Tagetes as a control option. In a pot experiment, Tagetes patula or Tagetes tenuifolia were grown in ARD soil, incorporated or removed. Nematodes extracted from untreated ARD soil and washed on 20 µm-sieves induced ARD symptoms when inoculated to apple saplings growing in a sterile substrate. In contrast, nematodes from Tagetes treated ARD soil did not reduce root growth compared to uninoculated plants, irrespective of Tagetes species and incorporation. In plots of five apple tree nurseries or orchards, either Tagetes or grass was grown on ARD soil. Nematodes extracted from the grass plots and inoculated to apple saplings significantly reduced plant growth compared to nematodes from Tagetes plots for all five farms. Apple rootstocks showed overall a significantly higher increase in shoot base diameter when grown on Tagetes-treated plots compared to grass plots, while this effect differed among farms. Plant-parasitic nematodes were too low in abundance to explain plant damage. In conclusion, the free-living nematodes involved in ARD can be controlled by Tagetes.

Parts produced by laser or electron-beam powder bed fusion (PBF) additive manufacturing are prone to residual stresses, deformations, and other defects linked to non-uniform temperature distribution during the manufacturing process. Several researchers have highlighted the important role scan sequence plays in achieving uniform temperature distribution in PBF. However, scan sequence continues to be determined offline based on trial-and-error or heuristics, which are neither optimal nor generalizable. To address these weaknesses, we have articulated a vision for an intelligent online scan sequence optimization approach to achieve uniform temperature distribution, hence reduced residual stresses and deformations, in PBF using physics-based and data-driven thermal models. This paper proposes SmartScan, our first attempt towards achieving our vision using a simplified physics-based thermal model. The conduction and convection dynamics of a single layer of the PBF process are modeled using the finite difference method and radial basis functions. Using the model, the next best feature (e.g., stripe or island) that minimizes a thermal uniformity metric is found using control theory. Simulations and experiments involving laser marking of a stainless steel plate are used to demonstrate the effectiveness of SmartScan in comparison to existing heuristic scan sequences for stripe and island scan patterns. In experiments, SmartScan yields up to 43% improvement in average thermal uniformity and 47% reduction in deformations (i.e., warpage) compared to existing heuristic approaches. It is also shown to be robust, and computationally efficient enough for online implementation.

Cryphonectria is a fungal genus associated with economically significant disease of trees. Herein we characterized a novel double-stranded RNA virus from the fungal species Cryphonectria naterciae, a species unexplored as a virus host. De novo assembly of RNA-seq data and Sanger sequencing of RACE (rapid amplification of cDNA ends) clones gave the complete, non-segmented genome (10,164 bp) of the virus termed Cryphonectria naterciae fusagravirus (CnFGV1) that was phylogenetically placed within the previously proposed viral family Fusagraviridae. Of 31 field-collected strains of C. naterciae, 40% tested CnFGV1-positive. Co-cultivation resulted in within-species transmission of CnFGV1 to virus-free strains of C. naterciae. Comparison of the mycelium phenotype and the growth rate of CnFGV1-infected and virus-free isogenic strains revealed frequent sectoring and growth reduction in C. naterciae. Co-culturing also led to cross-species transmission of CnFGV1 to Cryphonectria carpinicola and Cryphonectria radicalis, but not to Cryphonectria parasitica. The virus-infected C. naterciae and the experimentally infected Cryphonectria spp. readily transmitted CnFGV1 through asexual spores to the next generation. CnFGV1 strongly reduced conidiation and in some cases vegetative growth of C. carpinicola, which is involved in the European hornbeam disease. This study is the first report of a fusagravirus in the family Cryphonectriaceae and lays the groundwork for assessing a hypovirulence effect of CnFGV1 against the hornbeam decline in Europe.

Continuous and emerging advances in Information and Communication Technology (ICT) have enabled IoT-to-Cloud applications to be induced by data pipelines coupled with Edge Intelligence-based architectures. Advanced vehicular networks greatly benefit from these architectures due to the implicit functionalities that are focused on realizing the Internet-of-Vehicle (IoV) vision. However, IoV is susceptible to attacks, where adversaries can easily exploit existing vulnerabilities. Several attacks may succeed due to inadequate or weaker authentication techniques. Hence, there is a timely need for hardening the authentication process through cutting-edge access control mechanisms. This paper proposes a Blockchain-based Multi-Factor authentication model that uses an embedded Digital Signature (MFBC_eDS) for vehicular clouds and Cloud-enabled IoV. Our proposed MFBC_eDS model consists of a scheme that integrates the Security Assertion Mark-up Language (SAML) to the Single Sign-On (SSO) capabilities for a connected Edge-to Cloud ecosystem. MFBC_eDS draws an essential comparison with the baseline authentication scheme suggested by Karla and Sood. Based on the foundations of Karla and Sood’s scheme, an embedded Probabilistic Polynomial-Time Algorithm (ePPTA) and an additional Hash function for the Pi generated during Karla and Sood’s authentication are proposed and discussed. The preliminary analysis of the proposition shows that the approach is more suitable to counter major adversarial attacks in an IoV-centered environment based on Dolev-Yao adversarial model while satisfying aspects of the CIA triad.

The coronavirus disease 2019 (COVID-19) pandemic has led to wastewater surveillance becoming an important tool for monitoring the spread of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) within communities. As a result, molecular methods, in particular reverse transcription-quantitative PCR (RT-qPCR), have been employed to generate large data sets aimed at the detection and quantification of SARS-CoV-2 in wastewater. Although RT-qPCR is rapid and sensitive, there is no standard method that fits all use cases, there are no certified quantification standards and experiments are carried out using numerous different assays, reagents, instruments, and data analysis protocols. These variations can lead to the reporting of erroneous quantitative data resulting in potentially misleading interpretations and conclusions. We have reviewed the SARS-CoV-2 wastewater surveillance literature focusing on the variability of RT-qPCR data as revealed by inconsistent standard curves and associated parameters. We find that variation in these parameters and deviations from best practices as described in The Minimum Information for Publication of Quantitative Real-Time PCR Experiments (MIQE) guidelines suggest a lack of reproducibility and reliability in quantitative measurements of SARS-CoV-2 RNA in wastewater.

Current, application-driven trends towards larger-scale integration (LSI) of microfluidic systems for comprehensive assay automation and multiplexing pose significant technological and economical challenges to developers. By virtue of their intrinsic capability for powerful sample preparation, centrifugal systems have attracted significant interest in academia and business since the early 1990s. This review models common, rotationally controlled valving schemes at the heart of such “Lab-on-a-Disc” (LoaD) platforms to predict critical spin rates and reliability of flow control mainly based on geometries, location and liquid volumes to be processed, and their experimental tolerances. In absence of larger-scale manufacturing facilities during product development, the method presented here facilitates the provision of efficient simulation tools for virtual prototyping and characterization to greatly expedite design optimization according to key performance metrics. This virtual in silico approach thus significantly accelerates, de-risks and lowers costs along the critical advancement from idea, fluidic testing, bioanalytical validation and scale-up to commercial mass manufacture.

In the context of the COVID-19 pandemic, thousands of healthcare workers (HCWs) infected with COVID-19 have lost their lives worldwide. At the early stage of the epidemic, when COVID-19 was still not considered as a pandemic, a large number of Chinese HCWs were infected. Officials reported that more than 3,000 HCWs in Hubei contracted the virus at the early stage of the outbreak due to limited knowledge of the virus. Following reports of overloaded local hospitals, more than 42,000 medical staff, including those from the military, were dispatched to Hubei from across the country. At the peak of the fight, one in 10 intensive care medics in China were working in Wuhan. During fighting against COVID-19 in China, although a large number of HCWs were infected by SARS-CoV-2 in the early stages of the epidemic, the timely adoption of measures indicated that, a faster rate of diagnosis could be achieved, patients were isolated in-time, HCWs’ safety was prioritized, training on basic protective knowledge and unified management of HCWs was strengthened, and effective protective measures were implemented. This resulted in the accomplishment of zero SARS-CoV-2 infection among the 42,632 members of the national medical teams sent to Hubei, and the number of COVID-19 cases among HCWs in local hospitals also significantly decreased, thereby indicating that hospital-acquired infections of SARS-CoV-2 among HCWs are fully preventable.

With the continuous development of the mining industry, the world's major mines have gradually entered the intelligent stage. In the intelligent underground mine, the operation road of the underground transportation equipment is very complicated, and the monitoring and control of the underground traffic has become a problem to be solved in the intelligent underground mine. Therefore, on the basis of solving the practical problems of underground mines, the concept paper discusses the possibility of the rail transit monitoring system being applied to underground mines through the summary and induction of the related literature and propose the design for the CBTC system to solve the problems in the underground mine rail transportation. As the mining engineers, we put forward the concept of this design for the CBTC system in this concept paper, but we need to continue to work hard for the future development of the underground mines. And the concept paper serves as a guide to the Tossing out a brick to get a jade gem, has implications for the development and the future of the underground mine transportation.

This paper describes how to construct a low-cost magnetic levitation system (MagLev). The MagLev has been intensively used in the engineering education, allowing instructors and students to learn through hands-on experiments essential concepts, such as electronics, electromagnetism, and control systems. Built from scratch, the proposed MagLev depends only on simple, low-cost components readily available on the market. In addition to showing how to construct the MagLev, this paper presents a semi-active control strategy which seems novel when applied in the MagLev. Experiments performed in the laboratory have compared the proposed control scheme with the classical PID control. The corresponding real-time experiments illustrate both the effectiveness of the approach and the potential of the MagLev for education.

The paper is concerned with a class of stochastic differential equations in infinite dimensional Hilbert space with random coefficients driven by Teugel's martingales which are more general processes. and its optimal control problem. Here Teugels martingales are a family of pairwise strongly orthonormal martingales associated with L\'{e}vy processes (see Nualart and Schoutens). There are three major ingredients. The first is to prove the existence and uniqueness of the solutions by continuous dependence theorem of solutions combining with the parameter extension method. The second is to establish the stochastic maximum principle and verification theorem for our optimal control problem by the classicconvex variation method and dual technique.The third is to represent an example of a Cauchy problem for a controlled stochastic partial differential equation driven by Teugels martingales which our theoretical results can solve.

The most widespread intracellular bacteria in the animal kingdom are maternally-inherited endosymbionts of the genus Wolbachia. Their prevalence in arthropods and nematodes worldwide and a stunning arsenal of parasitic and mutualistic adaptations make these bacteria a biological archetype for basic studies of symbiosis and applied outcomes for curbing human and agricultural diseases. Here, we conduct a summative, centennial analysis of living in the Wolbachia world. We synthesize literature on Wolbachia’s host range, phylogenetic diversity, genomics, cell biology, and applications to filarial, arboviral, and agricultural diseases. We also review the mobilome of Wolbachia including phage WO and its essentiality to hallmark phenotypes in arthropods. Finally, the Wolbachia system is an exemplar for discovery-based science education using biodiversity, biotechnology, and bioinformatics lessons. As we approach a century of Wolbachia research, applications, and education, the interdisciplinary science and knowledge from this symbiosis stand as a model for consolidating and teaching the integrative rules of endosymbiotic life.

Introduction: Valproic acid (VPA) is an antiepileptic drug extensively used for treating partial and generalised seizures, acute mania and as prophylaxis for bipolar disorder. Drug-induced liver injury (DILI) persists as a significant issue related to fatal outcomes by VPA. The aim of this study was to increase our knowledge about this condition and to better identify patients affected. Methods: We conducted an observational retrospective case-control study that identified cases of DILI by VPA from the Pharmacovigilance Programme from our Laboratory Signals at La Paz University Hospital from January 2007 to December 2019. From the Therapeutic VPA Monitoring Programme, two control groups were assigned, VPA-tolerant patients and the other with patients who developed mild VPA-related hepatitis but who did not meet the DILI criteria, matched for date, age and sex. Results: A total of 60 patients were included in the study: 15 cases of DILI, 30 VPA-tolerant controls and 15 controls with mild hepatitis. Mean age for the cases was 45.7 years, 4(26.7%) were women and 5(33.34%) were children under 18 years, of them 3(20%) were fatal. Polytherapy with other antiepileptic drugs (p=0.047) and alcohol consumption (p<0.001) were associated with a greater risk of developing DILI by VPA. A diagnosis of epileptic seizure was more frequently related to DILI when compared with the VPA-tolerant controls (p<0.001). The cases developed hepatocellular hepatitis (p<0.001), while the mild hepatitis controls had a higher rate of cholestatic hepatitis (p<0.001). The laboratory lactate dehydrogenase values were statistically higher (even at baseline) in patients with DILI than in both control groups (p= 0.033 and p=0.039). Conclusions: VPA hepatotoxicity remains a considerable problem. This study offers interesting findings for characterising VPA-induced liver injury and at-risk patients.

High-performance motor drives that operate in harsh conditions require an accurate and robust angular position measurement to correctly estimate the speed and reduce the torque ripple produced by angular estimation error. For that reason, a resolver is used in motor drives as a position sensor due to its robustness. A resolver-to-digital converter (RDC) is an observer used to get the angular position from the resolver signals. Most RDCs are based on angle tracking observers (ATOs). On the other hand, generalized predictive control (GPC) has become a powerful tool in developing controllers and observers for industrial applications. However, no GPC-based RDC with zero steady-state error during constant speed operation was proposed. This paper proposes an RDC based on a second-order difference GPC (SOD-GPC). In SOD-GPC, the second-order difference operator is applied to design a GPC model with two embedded integrators. Thus, the SOD-GPC is used to design a type-II ATO whose steady-state angle estimation error tends to zero during constant speed operation. Simulation and experimental results prove that the proposed RDC system has better performance than other literature approaches.

Mitochondria are constantly subjected to stressful conditions due to their unique physiology and organization. The resulting damage leads to mitochondrial dysfunction, which underlies many pathophysiological conditions. Hence, constant surveillance is required to closely monitor mitochondrial health for sound maintenance of cellular metabolism and thus, for viability. In addition to internal mitochondrial chaperones and proteases, mitochondrial health is also governed by host cell protein quality control systems. The Ubiquitin-Proteasome System (UPS) and autophagy constitute the main pathways for removal of damaged or superfluous proteins in the cytosol, nucleus, and from certain organelles such as the ER and mitochondria. Although stress-induced ubiquitin-dependent degradation of mitochondrial outer membrane proteins has been widely studied, mechanisms of intramitochondrial protein ubiquitination have remained largely elusive due to the predominantly cytosolic nature of UPS components, separated from internal mitochondrial proteins by a double membrane. However, recent research has illuminated examples of intramitochondrial protein ubiquitination pathways and highlighted their importance under basal and stressful conditions. Owing to the dependence of mitochondria on the error-prone process of protein import from the cytosol, it is imperative that the cell eliminate any accumulated proteins in the event of mitochondrial import deficiency. Apparently, a significant portion of this activity involves ubiquitination in one way or another. In the present review article, following a brief introduction to mitochondrial protein quality control mechanisms, we discuss our recent understanding of intramitochondrial protein ubiquitination, its importance for the basal function of mitochondria, metabolic implications, and possible therapeutic applications.

Nowadays, many political campaigns are using social influence (SI) in order to convince voters to support/oppose a specific candidate/party. In election control via SI problem, an attacker tries to find a set of limited influencers to start disseminating a political message in a social network of voters. A voter will change his opinion when he receives and accepts the message. In constructive case, the goal is to maximize the number of votes/winners of a target candidate/party, while in destructive case, the attacker tries to minimize them. Recent works considered the problem in different models and presented some hardness and approximation results. In this work, we consider multi-winner election control through SI on different graph structures and diffusion models, and our goal is to maximize/minimize the number of winners in our target party. We show that the problem is hard to approximate when voters' connections form a graph, and the diffusion model is the linear threshold model. We also prove the same result considering an arborescence under independent cascade model. Moreover, we present a dynamic programming algorithm for the cases that the voting system is a variation of straight-party voting, and voters form a tree.

In this work, it is analyzed a Digital Signal Processor, DSP, based One Cycle Control, OCC, strategy for a Power Factor Corrector, PFC, rectifier, which presents Common-mode Voltage, CMV, immunity. The proposed strategy utilizes an emulated-resistance-controller in closed-loop configuration to set up dc-link voltage and achieve unity power factor, UPF. It is shown that if PFC can achieve UPF condition and if phase voltage is only affected by CMV, then phase current is free from CMV, as well as a lead-lag compensator, LLC, to average phase current. Another possible condition is also analyzed. The proposal is verified by simulation and experiments.

We present the design and overall development of an eight degrees of freedom (DOF) based Bioinspired Quadruped Robot (BiQR). The robot is designed with a skeleton made of cedar wood. The wooden skeleton is based on exploring the potential of cedar wood to be a choice for legged robots’ design. With a total weight of 1.19 kg, the robot uses eight servo motors that run the position control. Relying on the inverse kinematics, the control design enables the robot to perform the walk gait-based locomotion in a controlled environment. The robot has two main aspects: 1) the initial wooden skeleton development of the robot showing it to be an acceptable choice for robot design, 2) the robot’s applicability as a low-cost legged platform to test the locomotion in a laboratory or a classroom setting.

In this paper, a solenoid based linearly movable armature system is designed using robust control theory in order to improve the performance of the system. Reference track method is the best performance analysis for position control systems. Among the robust controllers, H infinity mixed-sensitivity and Mixed H 2 /H∞ with Regional Pole Placement Controllers are used to improve the performance of the system. Comparison of the proposed controllers for tracking a reference displacement signals (step and sine wave) and a promising simulation result have been obtained.

(1) Background: It is unclear whether the reported presenting clinical features of coronavirus disease 2019 (COVID-19) are useful in identifying high-risk patients for early testing and isolation in the emergency department (ED). We aimed to compare the exposure history, clinical, laboratory, and radiographic features of ED patients who tested positive and negative for COVID-19; (2) Methods: We conducted a case-control study in seven EDs during the first five weeks of the COVID-19 outbreak in Hong Kong. Thirty-seven laboratory-confirmed COVID-19 patients were compared with 111 age- and gender-matched controls; (3) Results: There were no significant differences in patient characteristics and reported symptoms between the groups, except patient-reported fever. A positive travel history or contact history was the most significant predictor for COVID-19 infection. After adjustment for age and presumed location of acquiring the infection in Wuhan/Hubei, patient-reported fever (OR 2.6, 95% CI 1.1 to 6.3), delayed presentation (OR 5.0, 95% CI 2.0 to 12.5), having medical consultation before ED presentation (OR 7.4, 95% 2.9 to19.1), thrombocytopenia (OR 4.0, 95% CI 1.6 to 9.7), raised lactate dehydrogenase (OR 5.9, 95% CI 1.9 to 18.5), haziness, consolidation or ground-glass opacity on chest radiography (OR 5.6, 95% CI 2.0 to 16.0), and bilateral changes on chest radiography (OR 13.2, 95% CI 4.7 to 37.4) were associated with a higher odds of COVID-19 separately while neutrophilia was associated with a lower odds (OR 0.3, 95% CI 0.1-0.8); and (4) Conclusions: This study highlights several features that may be useful in identifying high-risk patients for early testing and isolation while waiting for test result. Further studies are warranted to verify the findings.

How does the human neurophysiological system self-organize to achieve optimal phase relationships among joints and limbs, such as in the composite rhythms of butterfly and front crawl swimming, drumming, or dancing? We conducted a systematic review of literature relating to CNS control of phase among joint/limbs in continuous rhythmic activities. SCOPUS and Web of Science were searched using keywords ‘Phase AND Rhythm AND Coordination’. This yielded 998 matches from which 23 papers were extracted for inclusion based on screening criteria. The empirical evidence arising from in-vivo, fictive, in-vitro, and modelling of neural control in humans, other species, and robots indicates that the control of movement is facilitated and simplified by innervating muscle synergies by way of spinal central pattern generators (CPGs). These typically behave like oscillators enabling stable repetition across cycles of movements. This approach provides a foundation to guide the design of empirical research in human swimming and other limb independent activities. For example, future research could be conducted to explore whether the two-layer CPG model proposed by Saltiel et al [1] to explain locomotion in cats might also explain the complex relationships among the cyclical motions in human swimming.

Biological control is widely successful for controlling pests, but effective biocontrol agents are now more difficult to obtain due to more restrictive international trade laws. Coupled with increasing demand, the efficacy of existing and new biocontrol agents needs to be improved with genetic and genomic approaches. Although they have been underutilised in the past, applying genetic and genomic techniques is becoming more feasible from both technological and economic perspectives. We review current methods and provide a framework for using them, incorporating evolutionary and ecological principles. First, it is necessary to identify which biocontrol trait to select and in what direction. Next, the genes or markers linked to these traits need be determined to better target their selection, followed by how to implement this information into a breeding program. Choosing a trait can be assisted by modelling to account for the proper agro-ecological context, and by knowing which traits have sufficiently high heritability values. We provide guidelines for designing genomic strategies in biocontrol programs, which depends on the organism, budget, and desired objective. Genomic approaches start with genome sequencing and assembly. We provide a guide for deciding the most successful sequencing strategy for biocontrol agents. Gene discovery involves quantitative trait loci (QTL) analyses, transcriptomic and proteomic studies, and gene editing. Improving biocontrol practices include marker-assisted selection, genomic selection and microbiome manipulation of biocontrol agents, and monitoring for genetic variation during rearing and post-release. We conclude by identifying the most promising applications of genetic and genomic methods to improve biological control efficacy.

As more end devices are getting connected, the Internet will become more congested. A variety of congestion control techniques have been developed either on transport or network layers. Active Queue Management (AQM) is a paradigm that aims at mitigating the congestion on the network layer by active buffer control to avoid overflow. However, finding the right parameters for an AQM scheme is challenging, due to the complexity and dynamics of the networks. On the other hand, the Explicit Congestion Notification (ECN) mechanism is a solution that makes visible incipient congestion on the network layer to the transport layer. In this work, we propose to exploit the ECN information to improve AQM algorithms by applying Machine Learning techniques. Our intelligent method uses an artificial neural network to predict congestion and an AQM parameter tuner based on reinforcement learning. The evaluation results show that our solution can enhance the performance of deployed AQM, using the existing TCP congestion control mechanisms.

The growth of sustainable apparels provides grounding for the emergence of a new consumer market. Surprisingly, this movement has not only taken place in developed countries but also in emerging countries. To the best of the authors’ knowledge, no systematic reviews have been carried out on sustainable apparels, focused specifically on emerging countries. The goal of this systematic review is to analyse the existing literature on various factors that influence sustainable apparel consumption in emerging countries, as well as presenting future research directions. This detailed literature review is guided by the PRISMA Statement (Preferred Reporting Items for Systematic reviews and Meta-Analyses) review method, and its searches encompass sources such as Web of Science, Scopus and Google Scholar databases which, in result, identified 19 related studies. Furthermore, the reviewers segregated the factors into four major domains which include value, subjective norm, perceived behavioural control and knowledge. The results of this review demonstrate that most customers in the emerging countries have already experienced a growing interest in sustainable apparel with a strong development of knowledge, great concern, values and social circle. In sum, this systematic literature review provides an insightful information about sustainable apparel purchase behaviour and helps academicians, manufacturers and retailers to position and market their sustainable clothing brands.

For the task planning problem of the command and control architecture, the existing algorithms have problems such as low efficiency and poor re-planning quality under abnormal conditions. Based on the requirements of the current accusation architecture, this paper constructs a distributed command and control architecture model based on multi-agents, which makes use of the superiority of multi-agents in dealing with complex tasks. The concept of MultiAgents-HTN is proposed under the framework. The original hierarchical task network planning algorithm is optimized, the multi-agent collaboration framework is redefined, and the coordination mechanism of local conflict is designed. Taking the classical resource scheduling problem as the experimental background, the comparison between the proposed algorithm and the classical HTN algorithm is carried out. The experimental results show that the proposed algorithm has higher quality and higher efficiency than the existing algorithm, and the space anomaly is heavy during processing. The planning is more efficient, and the time is more complicated and superior in dealing with the same problem, with good convergence and adaptability. The conclusion proves that the distributed command and control architecture proposed in this paper has high practicability in related fields and can solve the problem of distributed command and control architecture in multi-agent environment.