Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

Injection molding is one of the most common and effective manufacturing processes used to produce plastic products and impacts industries around the world. However, injection molding is a complex process that requires careful consideration of several key control variables. These variables and how they are utilized greatly affect the resulting parts of any molding operation. The bounds of the acceptable values of each control process variable or CPV must be analyzed and delimited to ensure manufacturing success and produce injected molded parts efficiently and effectively. One such method in which the key CPV of an injection molding operation can be delimited is through the development of a process window. Once developed, operating CPV at values inside the boundaries of the window or region will allow for the consistent production of parts that comply with the desired performance measures (PM), promoting a stable manufacturing process. This work proposes a method to experimentally develop process windows and illustrates the methodology with a specific molding operation.

The protection of electronics against environmental influences and mechanical loads is important for integration of conventional electronics in textile conductive tapes. For this purpose, the sensors on the tapes are molded with plastic locally. This process step is recognized in the injection molding process. The molding compound is then later selected depending on: The field of application, the parameters of the manufacturing process and the textile tape properties. We have designed a mould for liquid silicone (LSR) as well as for the textile and electronic insertions. The cavities are sealed by a local compression of the textile and the two inserts are positioned with position pins representing the main aspect of the mould design. The sampling tool and the process parameter optimization are mainly based on the material properties of the silicone and the mechanical sensitivity of the inserts. To reduce the deformation of the circuit boards by the melt front and ensuring the functionality of the electronics a low-pressure process is used.

The application of optimization techniques to improve the performance of polymer processing technologies is of great practical consequence, since it may result in significant savings of materials and energy resources, assist recycling schemes and generate products with better properties. The present review aims at identifying and discussing the most important characteristics of polymer processing optimization problems in terms of the nature of the objective function, optimization algorithm, and process modelling approach that is used to evaluate the solutions and the parameters to optimize. Taking into account the research efforts developed so far, it is shown that several optimization methodologies can be applied to polymer processing with good results, without demanding important computational requirements. Also, within the field of artificial intelligence, several approaches can be reach significant success. The first part of this review demonstrated the advantages of the optimization approach in polymer processing, discussed some concepts on multi-objective optimization and reported the application of optimization methodologies in single and twin screw extruders, extrusion dies and calibrators. This second part focus on injection molding, blow molding and thermoforming technologies.

Magnetorheological elastomers (MREs) are in demand in the field of high-tech micro- and nano-industries such as biomedical applications and soft robotics due to their exquisite magneto-sensitive response. Among various MRE applications, programmable actuators are emerging as promising soft robots because of their combined advantages of excellent flexibility and precise controllability in a magnetic system. Here, we present the development of a magnetically programmable soft magnetic microarray actuators through field-induced injection molding using MREs, which consist of styrene-ethylene/butylene styrene (SEBS) elastomer and carbonyl iron powder (CIP). The ratio of the CIP/SEBS matrix is designed to maximize the CIP fraction based on a critical solids loading. Further, as part of the design of the magnetization distribution in micropillar arrays, the magnetorheological response of the molten composites is analyzed using the static and dynamic viscosity results for both the on- and off- magnetic states, which reflect the particle dipole interaction and subsequent particle alignment during field-induced injection molding process. To develop high aspect ratio soft magnetic microarray, X-ray lithography is applied to prepare the sacrificial molds with a height-to-width ratio of 10. The alignment of CIP is designed to achieve a parallel magnetic direction along the micropillar columns, and consequently, the micropillar arrays successfully achieve the uniform and large bending actuation of up to approximately 81˚ with an applied magnetic field. This study suggests that the injection molding process offers a promising manufacturing approach to build a programmable soft magnetic microarray actuator.

A novel approach for the long-term medical treatment of the inner ear is the diffusion of drugs through the round window membrane from a patient-individualized, drug-eluting implant, which is inserted in the middle ear. In this study, drug-loaded (10 wt% Dexamethasone) guinea pig round window niche implants (GP-RNIs, ~1.30 mm x 0.95 mm x 0.60 mm) were manufactured with high precision via micro injection molding (µIM, Tmold = 160 °C, crosslinking time of 120 s). The medical grade silicone elastomer MED-4244 (NuSil Technology LLC, Radnor, PA, USA) was used. Molds for µIM were 3D printed from a commercially available resin PlasGRAY V2 (Asiga, Alexandria, Australia, TG = 84 °C) via a high-resolution DLP process (xy-resolution of 32 µm, z-resolution of 10 µm, 3D printing time of about 6 h). Drug release, biocompatibility, and bio-efficacy of the GP-RNIs were investigated in vitro. GP-RNIs could be successfully produced. Wear of the molds due to thermal stress was observed. However, the molds are suitable for single use in the µIM process. About 10% of the drug load (8.2 ± 0.6 µg) was released after 6 weeks (medium: isotonic saline). The implants showed high biocompatibility over a time of 28 days (lowest cell viability ~80%). Moreover, we found anti-inflammatory effects over a time of 28 days in a TNF-α-reduction test. These results are promising for the development of long-term drug-releasing implants for human inner ear therapy.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

Background: Chronic lateral epicondylitis challenges the therapeutical approach; underlying mechanisms are incompletely understood; neuropathic pain and central and peripheral sensitization may explain the fact that botulinum toxin was found to play a role in pain and function management. Methods: We searched the literature for MeSH terms: lateral epicondylitis or synonyms and botulinum toxin. Results: We found 14 papers containing trials on botulinum toxin injection into the tendon or into the extensor muscles (particularly extensor carpi radialis brevis and extensor communis digitorum). We followed the administration pathways, doses, timing and side effects. Conclusion: With chronic course, the focus of the therapy shifts from the afflicted tendon to the inserting muscles, as muscle contracture may create a vicious loop to perpetuate and aggravate the disease. Doses, timing and side effects are discussed.

High-quality ionization injection methods for Wake Field Acceleration driven by lasers or charged beams (LWFA/PWFA) can be optimised so as to generate high-brightness electron beams with tuneable duration in the attosecond range. We present a model of the minimum bunch duration obtainable with low-emittance ionization injection schemes, by spotting the roles of the ionization pulse duration, of the wake field longitudinal shape and of the delay of the ionization pulse position with respect to the node of the accelerating field. The model is tested for the resonant multi-pulse ionization injection (ReMPI) scheme, showing that bunches having length of about 300as can be obtained with a ionization pulse having duration of 30fs FWHM

This study investigates cloud cavitation suppression around a model scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift-drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor-liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift-drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems.

N-acetyl-L-cysteine (NAC), a sulfhydryl-containing compound, is mainly used as a mucolytic and as an antidote for acetaminophen overdose. Flow injection and sequential injection systems were designed and optimized with the aim of providing precise, accurate and reliable flow methods for NAC determination in pharmaceuticals with very low sample and reagent consumption. Proposed methods are based on a redox reaction wherein NAC reduces a complex of Cu(II) and bathocuproine disulfonate (BCS) to orange [Cu(BCS)2]3– complex, which absorption was measured at λmax = 483 nm. The optimized FIA and SIA configuration yielded a linear calibration curve with correlation coefficients (R2 = 0.9999 and R2 = 0.9996) in the concentration range of 3.0 × 10–7 – 3.0 × 10–5 mol L–1 and analytical frequency of 120 h–1 for the FIA method and 4.0 × 10–7 – 4.0 × 10–5 mol L–1, at sampling rate 60 h–1 for the SIA method. The proposed flow methods were successfully applied for the determination of NAC in pharmaceutical products, as the results showed good agreement with the standard method prescribed by Pharmacopoeia. Recoveries were in the range from 98.4% to 101.9% for the FIA method and from 97.2% to 101.8% for the SIA method.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

With growing regulations on ship emissions, specifically carbon dioxide and nitrogen oxides, this study emphasizes the critical need for improving the performance of existing ship diesel engines. Focusing on easily modifiable injection conditions within the fuel system, the research aims to enhance combustion characteristics for operational ships. The study provides a concise analysis of the combustion performance improvements achievable in the field. The study employed a range of calculation conditions, spanning from fuel injection pressures of 20 MPa to 160 MPa, injection timing from 15 degrees before top dead center (BTDC) to 5 degrees after top dead center (ATDC), and spray angles varying between 10 degrees and 50 degrees. A comprehensive analysis was conducted, focusing on fuel distribution behavior, combustion dynamics, carbon monoxide (CO) production and extinction, as well as nitrogen oxide (NO) production. This thorough examination aimed to provide insights into the complex interplay of these factors in order to optimize combustion performance in ship diesel engines. The analysis indicated that substantial unburned fuel occurred at injection pressures below 40 MPa and spray angles less than 20 degrees. This issue was significantly mitigated when injection pressures exceeded 80 MPa or a spray angle of 40 degrees was employed. High flame propagation speeds were observed at injection pressures over 80 MPa and injection timings before BTDC 10. Carbon monoxide emissions were notably low when injection pressures exceeded 80 MPa and a 40-degree spray angle was used. Nitrogen oxide emissions were minimized under conditions of injection pressure below 40 MPa, injection timing after BTDC 5 degrees, and a spray angle between 30 and 40 degrees. The study concludes that the most effective injection conditions for concurrently reducing fuel consumption, minimizing incomplete combustion products, and lowering nitrogen oxide emissions in the target engine are optimal when the injection pressure is set at 80 MPa, the injection timing is positioned at 5 degrees before top dead center (BTDC), and the spray angle is maintained at 40 degrees.

X-rays production through betatron radiation emission from electron bunches is a valuable resource for several research fields. The EuAPS (EuPRAXIA Advanced Photon Sources) project, within the framework of the EuPRAXIA project, aims to provide 1-10 keV photons (soft X-rays) developing a compact plasma-based system designed to exploit self-injection processes that occur in highly nonlinear laser-plasma interaction (LWFA) to drive electron betatron oscillations. Since the emitted radiation spectrum, intensity, angular divergence, and possible coherence strongly depend on the properties of the self-injected beam, accurate preliminary simulations of the process are necessary to evaluate the optimal diagnostic device specifications. Dedicated tools for these tasks are under development: electron trajectories from particle-in-cell (PIC) simulations are currently undergoing numerical analysis through the calculation of retarded fields and spectra for various plasma and laser parameter combinations. At the same time, an analytical approach is being examined to obtain an expression for the emitted spectrum, assuming linear or quadratic electron energy variation. Code structure and some trajectories analysis results are presented.

The danger is still very large from cross site scripting attacks. When designing web applications We must follow as much as we can prevention rules and don’t leave any loophole to our programs. Experience is a great factor for programmers to know these attacks and for a trainee programmer is a difficult task to spot all the weak points. In this article we present a tutorial on launching an XSS attack and also we propose simple solutions.

Implementation of waterflood is with injected pressured water to reservoir to escalation oil production. Produced water is the dominated result from oil and gas mechanism in this world meanwhile 65% of water is injected back to the well for pressure maintenance, 30% for discharge aquifier condition and surface. For shaly sand, produced water usually bring coarse and suspended sand to the surface. Therefore, this sand level is needed to declining to avoid plugging in injection well until certain economic condition.

Here is analysed the process of water re-injection in the two hydrocarbon reservoirs/fields in the Upper Miocene sandstone reservoirs, located in the western part of the Sava Depression (Croatia). Namely, those are the "A" field with "L" reservoir and the "B" field with "K" reservoir. Both currently produce hydrocarbons using a secondary recovery method, i.e. water injection (in fact re-injection of the field waters). Three regional reservoir variables had been analysed, namely porosity, permeability and injected water volumes. The number of data was small in all three cases. For porosity: reservoir “L” included 25 data, reservoir “K” 19 data; for permeability: reservoir “L” 10 data, reservoir “K” 18 data; for injected volumes of water: reservoir “L” 10 data; reservoir “K” 3 data. It defined selection of mapping algorithms mostly designed for small datasets (less than 20 points), i.e. Inverse Distance Weighting, Nearest and Natural Neighbourhood. Additionally, the Ordinary Kriging was used, but only with jack-knifed variograms, producing many “artificial points”. Results are extensively tested, using cross-validation and shape recognitions, and the Inverse Distance Weighting method is described as the most appropriate approach for mapping permeability and injected volumes in both reservoirs (“K” and “L”). The Kriging could be slightly outlined as the best approach for porosity. Obtained maps made possible application of the modified geological probability calculation as tools for prediction of successfulness of future injection (probability of 0.56). Consequently, results made possible to plan future injection more efficiently, with smaller injected volumes and same of higher hydrocarbon recovery. That could prevent useless injection, decrease number of injection wells, and save energy and funds invested in such processes.

CO2 injection into geological formations is considered one way of mitigating the increasing levels of carbon dioxide concentrations in the atmosphere and its effect on and global warming. In regard to sequestering carbon underground, different countries have conducted projects at commercial scale or pilot scale and some have plans to develop potential formations for carbon dioxide storage. In this study, pure CO2 injection is examined on a model with the properties of bunter sandstone and then sensitivity analyses were conducted for some of the important parameters. The results of this study show that the extent to which CO2 has been convected in the porous media in the reservoir plays a vital role in improving the CO2 dissolution in brine and safety of its long term storage. We conclude that heterogeneity plays a crucial role on the saturation distribution and can increase or decrease the amount of dissolved CO2 in water. Furthermore, the value of absolute permeability controls the effect of the Kv/Kh ratio on the CO2 dissolution in brine. In other words, as the value of vertical and horizontal permeability decreases (i.e. tight reservoirs) the impact of Kv/Kh ratio on the dissolved CO2 in brine becomes more prominent. Additionally, reservoir engineering parameters, such as well location, injection rate and scenarios, also have a high impact on the amount of dissolved CO2.

Barley straw was used to reinforce PHB in a discontinuous semi-industrial process. Four different fibres were used as reinforcing material : sawdust (SW), defibred (DFBF), delignified (DBF) and bleached (BBF) fibres. Looking at the mechanical properties, onlythe elastic moduli (Et) revealed an improvement. Oppositely, the strengths at break, under both tensile and bending assays, tended to decrease, evidencing a poor affinity between both components. Thanks to the mechani-cal treatment applied on the fibre, DFBF appeared as the most promising filler with the mechani-cal properties of the composites closest to those of neat PHB. DFBF-based composites were then produced by means of a process intensification using a twin-screw extruder, and then moulded into flowerpots. Mechanical results showed almost the same properties between the discontinuous and intensification processes. The suitability of the material to be used on agriculture flowerpots was demonstrated by simulation. . PHB-DFBF composite material can be considered an alterna-tive to replace petrol-based products for applications in agriculture and horticulture.

Background: Regardless of the indisputable benefits of insulin therapy, initiating insulin for diagnosed children with diabetes might be intimidating for parents. This study assesses the experience, fears, barriers and adherence to insulin use among the parents of diagnosed children with diabetes. Methods: A cross-sectional online survey was utilized for data collection from 218 participants between February and March 2023 in Jordan. The survey consisted of six sections to evaluate and assess: sociodemographic for both children with diabetes and their parents, the experience of using the insulin, the diabetes fear of self-injecting questionnaire (D-FISQ), the barriers for insulin administration including both sociocultural and other insulin-related factors, and insulin adherence. Results: More than 80% of the participants perceived a number of sociocultural barriers to insulin administration such as the tendency for addiction, lower efficiency of insulin than oral medication, and preference for complementary medicine over insulin. More than two-thirds of the participants complained of insulin-related barriers such as infections and sudden death in addition to learning the correct injection method. The general fear level was low, 8.56±7.87 (out of 45); however, more fear of insulin injection and self-testing was significantly associated with both sociocultural and insulin-related barriers, especially at the younger age. Conclusion: The results of this study indicated that parents have several barriers to insulin administration, mainly related to insulin injection. Therefore, more awareness about insulin therapy can help adjust the cooperation of patients, acceptance of treatment, ending with improving the quality of life and well-being.

A overview on application of CO2 in the ironmaking and steelmaking process is presented. Study on resource utilization of CO2 is significant for the reduction of CO2 emissions and the coping with global warming. The paper introduces the research progress of CO2 utilization in the sintering, Blast Furnace, Converter, secondary refining, Continuous Casting and smelting process of stainless steel in recent years in China. According to the foreign and domestic research and application status, the paper analyzes the feasibility and metallurgical effects of the CO2 utilization in the ferrous metallurgy process. The paper mainly introduces such new techniques as 1) flue gas circulating sintering, 2) blowing CO2 through Blast Furnace tuyere and CO2 as a pulverized coal carrier gas, 3) top and bottom blowing CO2 in the converter, 4) Ladle Furnace and Electric Arc Furnace bottom blowing CO2, 5) CO2 as Continuous Casting shielding gas, 6) CO2 for stainless steel smelting, and 7) CO2 circulation combustion. CO2 has a very wide application prospect in ferrous metallurgy process and the quantity of CO2 utilization is expected to be 100kg per ton of steel. It will effectively facilitate the progress of metallurgical technology and strongly promote the energy conservation of metallurgical industry.

Generalised Modules for Membrane Antigens (GMMA) are outer membrane vesicles derived from Gram-negative bacteria that can be used to design affordable subunit vaccines. GMMA are highly immunogenic and capable to induce an optimal antigen-specific humoral immune response both in animals and humans. Despite their potent immunogenicity, GMMA are usually formulated with aluminum salts (Alum) to reduce their potential systemic reactogenicity. GMMA, in fact, contain agonists of Toll-Like Receptor 4 (TLR4) and TLR2 that possess pro-inflammatory activity. The adsorption of GMMA onto Alum is believed to reduce their systemic exposure. However, it has been found that GMMA formulated without Alum did not induce concerning signs of systemic reactogenicity in the rabbit model. Here we asked whether GMMA promote local reactogenicity. We immunized mice intramuscularly with GMMA alone or formulated with Alum and we analyzed the injection site during 7 days after treatment. We found that GMMA alone promoted only mild inflammation within the muscle, whereas Alum induced severe muscle inflammation, as expected. Thus, in the mouse model, GMMA demonstrated to possess mild reactogenic potential locally, while Alum is confirmed a major driver of local reactogenicity. Our results further support the idea to investigate the reactogenicity of GMMA formulated without Alum in clinical studies.

Knee osteoarthritis (KOA) is a progressive and multifactorial disease that leads to joint pain, muscle weakness, physical disability, and decreased quality of life. In KOA, hyaluronic acid (HA) quantity and molecular weight (MW) are decreased, leading to joint pain due to increased wear of the knee articular cartilage. Arthrogenic muscle inhibition, which is usually found in patients with KOA, is associated with joint inflammation, pain, and swelling, also causing muscle atrophy, primarily of the anterior thigh muscles, and hindering the rehabilitation process. The aim of our work was to determine if a single HA infiltration could minimize the effects of arthrogenic muscle inhibition in patients with KOA in the short term, using isokinetic dynamometry to evaluate the strength of the knee extensor and flexor muscles of the thigh. Thirty patients with KOA who underwent both clinical and isokinetic assessment, and that received a single injection of HA, were retrospectively included. Our results showed that a single intra-articular injection of HA significantly reduces pain and improves joint function at four weeks, while non-statistically significant improvements were observed for the reference isokinetic parameter (maximum torque) at both 90°/s and 180°/s. Further high-quality studies are necessary to confirm the results of our study.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

Photoreceptor degeneration is a major cause of untreatable blindness worldwide and has recently been targeted by emerging technologies, including cell- and gene-based therapies. Cell types of neural lineage have shown promise for replacing either photoreceptors or retinal pigment epithelial cells following delivery to the subretinal space, while cells of bone marrow lineage have been tested for retinal trophic effects following delivery to the vitreous cavity. Here we explore an alternate approach in which cells from the immature neural retinal are delivered to the vitreous cavity with the goal of providing trophic support for degenerating photoreceptors. Rat and human retinal progenitor cells were transplanted to the vitreous of rats with a well-studied photoreceptor dystrophy, resulting in substantial anatomical preservation and functional rescue of vision. This work provides scientific proof-of-principle for a novel therapeutic approach to photoreceptor degeneration that is currently being evaluated in clinical trials.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

This research aims to delve into the intricacies of combustion processes, specifically focusing on heating oil and a blend of heating oil with TPO (Tire Pirolysis Oil) in a self-developed evaporative combustion chamber featuring steam injection. The primary objective is to scrutinize the impact of steam injection on the combustion dynamics. Conducting a series of tests, the investigation involved the meticulous manipulation of stoichiometric ratios while introducing ambient air through gravity fuel flow. Subsequent iterations of these tests incorporated the introduction of steam into the ambient air stream. The examination encompassed the combustion of both heating oil and the TPO blend within the combustion chamber. The evaluation criteria comprised an in-depth analysis of flame characteristics, temperature distribution within the combustion chamber, and the quantification of emissions such as particulate matter (PM), nitrogen oxides (NOx), carbon dioxide (CO2), carbon monoxide (CO), and water vapor (H2O). Throughout the experimentation phase, commercially available diesel fuel served as the primary fuel source. To facilitate the tests, the combustion chamber under scrutiny was seamlessly integrated into an AVL engine test bench system. Essential parameters, including fuel consumption, were meticulously gauged using an AVL 735 fuel flow meter, while fuel temperature was monitored using the AVL 745 fuel temperature conditioning system. The intake air, a crucial element in the combustion process, was quantified with precision using an AVL Flowsonix sensor. Emission measurements were conducted meticulously using state-of-the-art equipment, with gaseous emissions analyzed using an AVL FTIR AMA i60 exhaust gas analyzer. Simultaneously, soot emissions were quantified through employment of an AVL Micro Soot sensor. This comprehensive approach not only delves into the fundamental aspects of combustion but also extends its reach to the exploration of innovative techniques, such as steam injection, to enhance combustion efficiency and reduce emissions. The integration of advanced measurement tools ensures a robust and thorough analysis of the combustion process and its environmental implications.

A common requirement of embedded software in charge of safety tasks is to guarantee the identification of those Random Hardware Failures (RHFs) that can affect digital components. RHFs are unavoidable. For this reason, functional safety standards, like the ISO 26262 devoted to automotive applications, require embedded software designs able to detect and eventually mitigate them. For this purpose, various software-based error detection techniques have been proposed over the years, focusing mainly on detecting Control Flow Errors. Many Control Flow Checking (CFC) algorithms have been proposed to accomplish this task. However, applying these approaches can be difficult because their respective literature gives little guidance on the their practical implementation in high-level programming languages, and they have to be implemented in low-level code, e.g., assembly. Moreover, the current trend in the automotive industry is to adopt the so-called Model-Based Software Design approach, where an executable algorithm model is automatically translated into C or C++ source code. This paper presents two novelties: firstly, the compliance of the experimental data on the capabilities of Control Flow Checking (CFC) algorithms with the ISO 26262 automotive functional safety standard; Secondly, by the implementation of the CFC algorithm in the application behavioral model is automatically translated. There is no need to modify the code generator. The assessment was performed using a novel fault injection environment targeting a RISC-V (RV32I) microcontroller.

Every simplification has the potential to add a systematic error to the measured value. Sometimes, the addition does not render the measurement useless. In the case of oil well flow measurements based on the thermal properties of the fluid in the well, the addition of a systematic error of up to 20% can occur if the variation in the internal energy of the fluid and, most importantly, the transient nature of heat transfer in the completion are not taken into account. This error is a mathematical consequence of the simplifications chosen. To work within the first hours of good operation, given the need for immediate application in a prototype water injection well developed and installed at the UFRN, this article presents an analytical solution for calculating the flow rate by solving the differential equations obtained by applying the principles of mass and heat transfer. As a result, at the cost of greater complexity, the systematic error drops to values of less than 1% in the first two hours of operation of the well, as seen throughout this document.

In the investment casting process, the pattern made of wax is obtained in a die for further formation of shell mold. This work investigates commercial pattern waxes fluidity with a newly developed injection fluidity test. A good correlation between wax fluidity and its viscosity is observed, which is different from metallic alloys, where the solidification behavior is more critical. The difference in investigated filled waxes fluidity can be associated with the type and amount of filler.

A chronically stable electrode material with low impedance for recording neural activity and high charge-injection capacity for functional electro-stimulation is desirable for the fabrication of implantable microelectrode arrays that aims to restore impaired or lost neurological functions in humans. For this purpose, we have investigated the electrochemical properties of sputtered ruthenium oxide (RuOx) electrode coatings, deposited on planar microelectrode arrays, using an inorganic model of interstitial fluid (model-ISF) at 37o C as the electrolyte. Through a combination of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) modelling study we have established the contribution of faradaic reaction as the major charge-injection contributor within the safe neural stimulation potential window of 0.6 V vs Ag|AgCl. We have also established the reversibility of the charge-injection process for sputtered RuOx film by applying constant charge-per-phase current stimulations at different pulse widths and by comparing the magnitudes of leading and trailing access voltages during voltage transient measurements. Finally, the impedance of the sputtered RuOx film was found to be reasonably comparable in both its oxidized and reduced states, although electronic contribution from capacitive double-layer was found to be slightly higher for the completely oxidized film around 0.6 V than its reduced counterpart around -0.6V.

This article provides insight into flow measurement techniques in water injection wells in oil production fields, with a particular focus on the initial phases of operation. Consequently, the method created by Ramey in 1962, originally intended for estimating the temperature of the injection fluid, has been adapted to calculate the flow rate. In this technique, the calculation This procedure is based on the correlation between the thermal flux formed in the well. The discrepancy between the temperatures of the injected liquid and the geothermal temperature of the reservoir is the main source of the systematic errors in Ramey’s technique. To a lesser extent, but still significant, failure to observe the injection time in a fluid variation also results in an error problem that needs the failure to adhere to the scheduled injection time for a fluid alteration also yields a notable error dilemma that needs to be fixed. The reduction of listed systematic errors is the product of the main part of this article.

An 18.8–33.9-GHz, 2.26-mW current-reuse (CR) injection-locked frequency divider (ILFD) for radar sensor applications is presented in this paper. A fourth-order resonator is designed using a transformer with a distributed inductor for wideband operating of the ILFD. The CR core is employed to reduce the power consumption compared to conventional cross-coupled pair ILFDs. The targeted input center frequency is 24 GHz for radar application. The self-oscillated frequency of the proposed CR-ILFD is 14.08 GHz. The input frequency locking range is from 18.8 to 33.8 GHz (57%) at an injection power of 0 dBm without a capacitor bank or varactors. The proposed CR-ILFD consumes 2.26 mW of power from a 1-V supply voltage. The entire die size is 0.75 mm ´ 0.45 mm. This CR-ILFD is implemented in a 65-nm CMOS technology.

The paper presents results from investigation focused on toxicity content in the exhaust gases emitted by the internal combustion compression ignition engine fueled with glycerol-ethanol blends at ratio of 50/50% by volume. Innovative issue of this engine is application of 2 high pressure injectors for glycerol-ethanol blend and diesel fuel direct injection at high pressure over 200 MPa. As known, glycerol is considered is by-product from biodiesel production technologies, hence its cost is relatively low to other renewable alternative fuels, which can be applied as a fuel to the reciprocating piston engines. Tests on exhaust gases toxicity were performed. It was found that the toxic components UHC, NOx and CO were below the maximal allowed limits. Both NOx and smoke emissions were strongly reduced with increase in glycerol-ethanol fraction in the fuel. Summarizing, such a fueling strategy proposed in this paper made it possible to effectively and environmentally friendly combust crude glycerol in the compression ignition engine working in a heat and power cogeneration unit. Exhaust gas emission tests conducted in this case confirmed usability of this technology to be implemented into practice.

The use of biodiesel fuels in compression ignition engines leads to decrease CO, PM, HC and smoke opacity. However, NOx emissions increase importantly. Various methods to reduce NOx are used namely the EGR, the water injection method and the steam injection method. In this study, the steam injection method has been used instead of the other methods because of its benefits. This study examines the effects of steam injection on combustion products of diesel and biodiesel fuels by considering chemical equilibrium in order to determine the equilibrium combustion products involving 10 combustion products. A developed simulation code determing the equilibrium mole fractions and thermodynamic properties of combustion products is used for diesel and biodiesel fuels. It can be used for any fuel consisting of carbon, hydrogen or any oxygenated fuel. The results show that the mole fraction of CO2 and CO decrease with the steam injection ratios. NO mole fractions decrease with steam injection for lean mixtures but they increase slightly in the case of rich mixtures. The specific heat of combustion products increase with the steam injection ratios. Thus, the engine performance can be improved using the method. The model has been validated by comparing model results with the ones of NASA CEA software and GASEQ software using the methane as fuel. The relative errors of equilibrium mole fractions and thermodynamic properties of combustion products are less than 0.98 %.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

As a critical component of electric vehicles, the powertrain has a significant impact on the overall performance of the vehicle. In addressing the challenge of lengthy testing cycles, this study develops a para model of the powertrain utilizing digital twin (DT) technology, thereby establishing a framework for simulation testing of multi-controller intermodulation. The research conducts functional definition coverage testing through the design of specific functional requirement use cases, and it validates the failure mechanism via fault injection use cases. The results indicate that the DT testing platform can effectively simulate the operational interactions among various controllers within the powertrain system. In comparison to traditional field testing, the digital twin-based testing methodology offers enhanced operational efficiency and allows for the examination of testing conditions that are impractical to implement in real vehicles, particularly in the context of fault injection testing, thus facilitating the early detection of potential safety risks within the system. The advancement of this technical solution holds significant practical implications for the future mass production and development of electric vehicles.

The ultrasound guided viscosupplementation of the hip joint with hyaluronic acid(HA)is considered a standard procedure among the conservative treatments for hip arthritis.The aim of the study was to evaluate the clinical benefit and the incidence of adverse events of the technique in a obseravtional study at one year follow up. We evaluated a consecutive series of 85 patients with a diagnosis of symptomatic arthritis that performed intra-articular ultrasound-guided hyaluronic acid injections. The scales used for evaluation were modified Harris Hip Score(mHHS),WOMAC (Western Ontario and McMaster University),Hip Outcome Score (HOOS) with subscale Sport (HOOSs), for pain the Visual Analogic Scale (VAS).The patients were classified according to Tonnis’ radiological classification of arthrosis (range 0-3):20 patients(grade 0),32(grade 1),18(grade 2),15(grade 3).At last follow up all the scales increased:mHHS from 59.35 to 82.1,HOOS from 69.45 to 78.53,HOS Sport from 47.4 to 58.11,VAS from 6.09 to 3.97,WOMAC from 33.2 to 31.5 (p<0.05 for all the parameters);13/85 requested arthroplasty. Based on our findings, indication for use of hyaluronic acid is limited to patients with mild to moderate arthritis.Patients in advanced arthritis refusing replacement surgery and asking for this treatment should be informed about the poor results of the technique even in the short term follow up.

We have recently introduced the possibility of performing operando small-angle X-ray scattering measurements using a novel industrially relevant injection moulding system for plastics. We show that useful time-resolving measurements can be performed with a time-cycle of 1s and we highlight the possible steps to reduce this to 0.5s. We show how we can use the transmission measurements to provide a time-marker when plastic first enters the mould cavity in the region probed by the incident X-ray beam. We show the opportunities provided by this experimental stage mounted on the NCD-SWEET beamline at ALBA to probe the reproducibility of the injection moulding system on different scales. The design of the equipment allows the development of the structure and the morphology to be evaluated in different parts of mould cavity and we evaluate any differences in a rectangular mould cavity. We identify future prospects for this equipment in terms of novel mould heating and cooling systems and the opportunities for quantitatively evaluating radical approaches to injection moulding technology.

A wide variety of applications require high peak laser intensity in conjunction with a narrow spectral linewidth. Typically, injection-locked amplifiers have been employed for this purpose, where a continuous wave oscillator is amplified in a secondary external resonant amplifier cavity using a pulsed pump laser. In contrast, here we demonstrate a setup that combines a CW Ti:sapphire oscillator and pulsed amplifier in a single optical cavity, resulting in a compact system. Dichroic beam combination of blue wavelength semiconductor diodes and the green wavelength of a Nd:YAG laser allowed the simultaneous excitation of the Ti:sapphire crystal by both continuous-wave and pulsed pump sources. A linewidth of &lt;2MHz is achieved in continuous wave operation, while the linewidth increases to about 10MHz in the combined CW + pulsed mode with a pulse duration of 73ns. A peak pulse intensity of 0.2kW is achieved, which should enable efficient single-pass second harmonic generation in a nonlinear crystal.

The Oil reservoirs with low permeability account for a large proportion in the world, they surpass half of the total number of the oil reservoirs in China, it is important to exploit this kind of reservoir effectively. The exploitive results of these reservoir using normal water flooding methods are very poor because of the thine pores, bad connections and so on. However, these problems can be well solved by applying gas injection techniques. In this paper, the effects on the recovery effects exerted by the injection parameters such as the oxygen content in the injected air, the injection speed etc. were studied by several experiments using independently designed equipments aiming at one low permeable sandstone reservoir in China. Several conclusions were made from the experiment results: the best recovery effects can be achieved by injecting the oxygen reduced air with 8% of oxygen at the speed of 0.3ml/min (7.41×10-4PV/min) using the methods of injecting the air slugs and the foaming agent slugs alternately; the best oxidation time of the oil was 168 hours and the final oil recovery could be enhanced by 26.5% in this method. It was also showed by the experiments that the larger the permeability ratio is, the larger the recovery factor will be increased. At last, several equations about relationships between the EOR and the air injection parameters were revealed according to the results of the experiments which may offer some references to the LTO process mechanisms study in the similar oil reservoir.

In GDI engine applications, high-pressure (H.P.) injectors typically require to be designed to be capable of rapid response for GDI engines in order to be driven in the rapid response with respect to magnetic actuators, allowing for example more precise air-fuel ratio control in the GDI engines. The H.P. fuel injector is a highly dynamic component requiring careful voltage and pressure input modulation to achieve the required fuel injection quantities of GDI engines. The accurate fuel injection curves are a key influence for this technology, therefore will require the estimation of the fuel flow rate to be realized. In this paper, a PIC microchip for programming injector drive circuits is implemented to improve the performance of a H.P. fuel injector and tested to verify its feasibility. In the proposed injector drive circuit, powers MOSFETs directly control the charging/discharging current by a dsPIC30F4011 microchip. Design and analysis of the proposed injector drive circuit are presented. Next, effects of total pulse width, injector supply voltage, fuel system pressure and PWM operation on fuel injection quantities of a H.P. fuel injector are measured. Also, the measured data of the H.P. fuel injector fed by the injector driving circuit are defined as the fuel injection curves. Finally experimental results are provided for verification of the proposed injector drive circuit.

This paper presents a 612–1152 MHz Injection Locked Frequency Multiplier (ILFM). The proposed ILFM is only used for sending an input signal to the receiver in the I/Q mismatch calibration mode. Using the Phase-Locked Loop (PLL) to calibrate the receiver places a burden on this system due to the extra area required and power consumption. Instead of the PLL, to satisfy high frequency, low jitter, and low area, a Ring Oscillator is proposed. The free-running frequency of the ILFM is automatically digitally calibrated to reflect the frequency of the injected signal from the harmonics of the reference clock. To control the frequency of the ILFM, the load current is digitally tuned with 6-bit digital control signal. The proposed ILFM locks to the target frequency using a digitally controlled Frequency Locked Loop (FLL). This chip is fabricated using 1-poly 6-metal 0.18 µm CMOS and achieve the wide tuning range of 612–1152 MHz. The power consumption is 0.95 mW from a supply voltage of 1.8 V. The measured phase noise of the ILFM is −108 dBc/Hz at a 1 MHz offset.

In this paper, a low-power Injection-Locked Clock and Data Recovery (ILCDR) using 28nm FDSOI technology is presented. The back-gate auto-biasing of UTBB-FDSOI transistors allows us to create a QRO (Quadrature Ring Oscillator) reducing both size and power consumption. By injecting a digital signal into this circuit, we realize an Injection-Locked Oscillator (ILO) with low jitter. Thanks to the good performance of this oscillator, we propose a low power ILCDR with fast locking time and low jitter for burst-mode applications. The main novelty consists in the implementation of a complementary QRO based on back-gate control using FDSOI technology to realize a simple and efficient ILCDR circuit. With a Pseudo-Random Binary Sequence (PRBS7) at 868Mbps, the recovered clock jitter is 26.7ps (2.3%UIp-p) and the recovered data jitter is 11.9ps (1%UIp-p). With a 0.6V power supply, the power consumption is 318μW. The estimated Chip area is around 6600μm².

The automotive industry is under growing pressure from regulatory agencies to improve the recyclability of their plastic components. Simultaneously, manufacturers are adopting natural fiber composites in vehicles to reduce carbon footprints and decrease reliance on petroleum-based materials. This presents a challenge at vehicle end-of-life however, as natural fiber-reinforced polymers are substantially more difficult to recycle than their unreinforced counterparts. This study investigated the development of a mechanical recycling process for paper fiber-reinforced polypropylene composites, focusing on the impact of injection molding parameters—specifically, injection temperature and rate—on the thermal, mechanical, and water uptake properties of the composites. The results showed that processing temperature had a greater influence on composite performance than injection rate, with some limited interaction effects between the two. Higher processing intensity damaged the paper fibers, increasing the number of nucleation sites and resulting in greater polypropylene crystallinity. These structural changes reduced tensile properties at higher intensities, while flexural properties improved. Objective function analysis was applied to identify optimal processing conditions, balancing these competing trends. Overall, the findings demonstrate that paper fiber-reinforced polypropylene composites can be recycled into automotive relevant injection molding compounds using conventional plastic manufacturing techniques, though careful tuning of processing parameters is essential to achieve optimal performance.

Purpose To investigate the effects of intra-articular glenohumeral joint triamcinolone injection in treating secondary adhesive capsulitis after breast cancer surgery.Methods This study prospectively enrolled 37 participants, 22 of the breast cancer surgery group and 15 of the idiopathic group. All participants received intra-articular glenohumeral joint injection in the affected shoulder joint and received physiotherapy for 12 week. The clinical assessment evaluated before, and 1, 3, and 6 months after the intervention. The primary outcome was the change in the Shoulder Pain and Disability Index (SPADI).Results The total SPADI(%) in both groups showed significant decrease from baseline to 1, 3, and 6 months after the intervention. There was no significant difference in the differences of the total SPADI from baseline to 1, 3, and 6 months between two groups. However, the improvement in the SPADI pain subscale and the PROM of abduction at 3 and 6 months post-injection in the breast cancer group were inferior to the idiopathic group.Conclusion Intra-articular triamcinolone injection for adhesive capsulitis after breast cancer surgery significantly improved in significant improvements of pain, shoulder function and the PROM. The effects were similar to idiopathic adhesive capsulitis, but in the breast cancer surgery group, appropriate pain and ROM management and monitoring are required even 3 months after injection. With a standardized injection protocol, intra-articular triamcinolone injection could be an effective and safe treatment option for secondary adhesive capsulitis after breast cancer surgery.

Recycled tire fibers (RTF) are currently one of the most abundant waste not being recovered due to several processing hurdles and the presence of high amounts of residual ground rubber particles (GR). Therefore, this study proposes a simple approach to separate most of rubber particles from fibers and to determine their rubber content using thermogravimetric analysis (TGA)/calcination. Afterwards, clean fiber (CF) and GR are used as fillers for recycled post-consumer low density polyethylene (rLDPE), and their effects on the physical properties are investigated. Accordingly, a series of composites with CF and GR is prepared at different filler concentrations (0-30%) via extrusion compounding before using compression molding and injection molding for comparison. In all cases, injection molding leads to higher strength and modulus, but lower elongation at break. The results show that incorporating 30 wt.% of CF into rLDPE yields a remarkable improvement in tensile strength (15%), tensile modulus (192%) and flexural modulus (142%). On the other hand, the incorporation of up to 30 wt.% of GR results in a reduction of both tensile strength and flexural modulus by 15%, confirming the critical role of the cleaning process for RTF in achieving the best results.

The presented research focused on the evaluation of the novel concept of overmolding technique using self-reinforced composite prepregs and recycled polymer blends. In order to evaluate the effectiveness of the proposed manufacturing technique, several series of materials based on polycarbonate/polyethylene terephthalate (PC/PET) and polycarbonate/polyethylene terephthalate glycol (PC/PETG) blends were prepared. The reinforcing component in the form of overmolded prepreg was made from polyester-based self-reinforced composite (srPET). The prepared materials were compared in terms of mechanical properties and heat resistance; the study was supplemented by thermal analysis measurements (DMTA, DSC). Considering the mechanical characteristics, the overmolding technique turns out to be an effective method of improving the properties of composites, and the increase in impact strength turns out to be particularly beneficial. The increase of the impact strength for overmolded PC/PET blend reached 430 % for PC/PETG sample 330% , while for PC-based composite, only 100%. The expected improvement in thermomechanical properties turned out to be difficult to achieve due to the rapid softening of the srPET prepreg at around 70 °C. However, technological tests and analysis of properties clearly indicated that the use of PC-based blends makes it possible to create a permanent connection with reinforcement based on srPET prepregs, which can significantly expand the potential of applications of this type of materials.

Purpose: The intervertebral disc is a leading avascular organ in the body that may gather nutrition through diffusion. It maintains homeostasis by the use of autophagy and apoptosis to survive in unfavorable conditions such as stress and mechanical force. Therefore, excessive force and stress beyond normal conditions may cause intervertebral disc degeneration. The purpose of this study was to examine which is the better method, either external fixator (EF) or saline injection (SI), for inducing autophagy and apoptosis-mediated nucleus pulposus (NP) cell death in the discs of rat tail’s. Methods: Sixteen, nine-weeks-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross Kirschner wires) for a period ofsix and twelve weeks. Treated discs were dissected to identify the participation of autophagy and apoptosis in intervertebral disc degeneration. For identification purposes, H&amp;E staining, Masson’s trichrome staining, and immunohistochemistry (IHC) for LC3, beclin-1, and P62 in addition to MMP-2, MMP-3, and TIMP-1 were performed. Furthermore, we performed real-time polymerase chain reaction (RT-PCR) to observe autophagy-related gene expression (beclin-1, LC3, and P62) and apoptosis-related gene expression (MMP-2, MMP-3, and TIMP-1). Results: TheEF group showed more insidious NP cell degeneration than the control (Ctrl) group. Degeneration was elevated with increasing compression duration of EF group, whereas the SI group could not distinguish the margin of annulus fibrosus (AF) and NP cells. LC3, beclin-1, and P62 showed the highest and lateral expression whilst MMP-2, MMP-3, and TIMP-1 showed up-regulated and central expression in both groups, although the SI group could not recognize the boundary between NP and AF cells. The EF group showed the highest autophagy-related gene expression whereas the SI group showed lower expression. In addition, the EF group showed more autophagy-accumulating materials than the SI group which elevated with increasing compression duration. Furthermore, the SI group induced the highest apoptotic gene expression, but the EF group showed the lowest expression. Conclusion: The EF method was better for studying autophagy and apoptosis because it enhanced intervertebral disc degeneration after compression, which is actively linked to autophagy and apoptosis. The degeneration process was elevated by increasing the compression duration, but SI could not distinguish AF and NP cell margins.

Purpose: Intervertebral disc is a leading avascular organ in the body. Hence, it may utilize autophagy and apoptosis to alive in unfavorable condition like stress and mechanical force. But excessive force and stress is a key cause to intervertebral disc degeneration (IVDD). Purpose of this study is to identify, external fixator (EF) and saline injection (SI) may induce autopahgy and apoptosis mediated nucleus pulposus (NP) cells death in rat tail’s disc and which method is better for studying autophagy and apoptosis. Methods: Sixteen 9-week-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross kirschner wires) for 6 weeks and 12 weeks as well. Treated discs were dissected for checking out participation of autopahgy and apoptosis to intervertebral disc degradation (IVDD). For identifying them, we performed H&E staining, Masson’s trichrome staining, and Immunohistochemistry (IHC) for LC3, Beclin-1and P62 as well as MMP-2, MMP-3 and TIMP-1.Furthermore, we performed quantitative polymerase chain reaction (qPCR)to check out autophagy related gene expression (beclin-1, LC3 and P62) and apoptosis related gene expression (MMP-2, MMP-3 and TIMP-1) respectively. Results: More insidious nucleus pulposus (NP) cell degeneration was indentified in (EF) group than in (Ctrl) control group. And rate of degradation was elevated with increasing duration of compression, but SI group cannot distinguish the margin of AF and NP cells. Highest along with lateral expression was found for LC3, Beclin-1, and P62 of both groups. Up-regulated and central expression was observed for MMP-2, MMP-3 and TIMP-1 of both groups, although SI group cannot recognize the margin between NP and AF cells. Utmost autophagy related gene expression was identified in EF group than in SI group. Besides, maximum autophagy accumulating materials was found in EF group than in SI group. And it was amplified along with increasing the duration of compression. Highest, apoptotic gene expression was observed in SI group, whereas, EF group showed lowest expression. Conclusion: External fixator (EF) method was better to study autophagy and apoptosis because it enhanced IVDD after compression which is actively linked with autophagy and apoptosis. Degeneration process was conversely proportional along with duration of compression. On contrary, saline injection (SI) could not distinguish AF and NP cell border.

We describe the design and fabrication of an industrial injection moulding system which can be mounted and used on the NCD-SWEET Small-angle X-Ray Scattering Beamline at ALBA. We show how highly useful time-resolved data can be obtained using this system. We are able to evaluate the fraction of material in the mould cavity and identify the first material to solidify and how this varies with the injection tem-perature. The design follows current industrial practice and provides opportunities to collect time-resolved data at several points within the mould cavity so we can build up a 4D perspective of the morphology and its temporal development. The quantitative data obtained will prove invaluable for the optimisation of the next generation of in-jection moulding techniques. This preliminary work used results from the injection moulding of a general purpose isotactic polypropylene.

Within the context of ever wider expansion of direct injection in spark ignition engines, this investigation was aimed at improved understanding of the correlation between fuel injection strategy and emission of nanoparticles. Measurements performed on a wall guided engine allowed identifying the mechanisms involved in the formation of carbonaceous structures during combustion and their evolution in the exhaust line. In-cylinder pressure was recorded in combination with cycle-resolved flame imaging, gaseous emissions and particle size distribution. This complete characterization was performed at three injection phasing settings, with butanol and commercial gasoline. Optical accessibility from below the combustion chamber, allowed visualization of diffusive flames induced by fuel deposits; these localized phenomena were correlated to observed changes in engine performance and pollutant species. With gasoline fueling, minor modifications were observed with respect to combustion parameters, when varying the start of injection. The alcohol, on the other hand, featured marked sensitivity to the fuel delivery strategy. Even though the start of injection was varied in a relatively narrow crank angle range during the intake stroke, significant differences were recorded, especially in the values of particle emissions. This was correlated to the fuel jet-wall interactions; the analysis of diffusive flames, their location and size confirmed the importance of liquid film formation in direct injection engines, especially at medium and high load.

The permeability, heat conductivity and reaction rate will be varied with the change of natural gas hydrate saturation, when thermal fluid injected into the natural gas hydrate reservoirs. In order to characterize the variation of physical field parameters with hydrate saturation, DDF-LBM was applied to simulate the hydrate dissolving process by thermal fluid injection under pore scale modelling. Based on the forced conjugate heat transfer case, the relaxation frequency of the thermal lattice in the pores is corrected. Based on the P-T phase equilibrium relationship of hydrates and considering the heat absorbed by the hydrate reaction, the solid-liquid state of the hydrate lattice is judged in real time, and the dynamic simulation of the heat flow solidification multi-physics field is realized. The simulation results show that the dissolution rate of hydrates by thermal fluid injection was higher than that by heating the hydrate surface alone, and was positively correlated with the hydrate saturation. On the basis of the above results, this paper provided exponential fitting equations between different hydrate saturations and average permeability, effective thermal conductivity, and inherent reaction rate. The fitting results show that saturation has a negative correlation with relative permeability and effective thermal conductivity, and a positive correlation with the inherent reaction rate. The above results can provide a reference basis for accurately describing the heat and mass transfer of natural gas hydrate under macro-scale.

Recently, deep neural networks (DNNs) have been widely used in various fields such as autonomous vehicles and smart homes. Since these DNNs can be directly implemented on edge devices, they offer advantages such as real-time processing in low-power and low-bandwidth environments. However, deployment of DNNs in embedded systems, including edge devices, exposes them to threats such as fault injection attacks. In this paper, we introduce two methods to induce misclassifications by using clock and voltage glitch-based fault attacks in devices where DNN models are executed. As a result of experiments on a microcontroller implemented with a DNN for image classification, we show that glitch injection attacks can lead with high probability to serious misclassifications. Furthermore, we propose a countermeasure to glitch attacks on the softmax function, and confirm that this method is effective in preventing misclassifications.

Background: Removable prostheses have seen a fundamental change recently because of advances in polymer materials, allowing improved durability and performance. Despite these advancements, notable differences still occur amongst various polymer materials and processing technologies, requiring a thorough grasp of their mechanical, physical, and therapeutic implications. Methods: Fours different processing techniques, all utilizing Polymethyl methacrylate (PMMA) as the main material, were used to construct complete dentures. The specimens underwent a mechanical test. Results: All the specimens broke under the influence of a certain force, rather than yielding through flow, as is characteristic for plastic materials. For each specimen, the maximum force (N) was recorded (figure 4), as well as the breaking energy, Conclusions: The best results were obtained in the case of the thermoplastic injection system and, surprisingly and contrary to those in the specialized literature, the worst results were recorded in the case of 3D printed samples.

Solar geoengineering (SG) solutions have many advantages compared to the difficulty of carbon removal (CR): SG produces fast results, is shown here to have much higher efficiency than CR, is not related to fossil fuel legislation, and is something we all can participate in brightening the Earth with cool roofs, and roads. SG requirements detailed previously to mitigate global warming (GW) have been concerning primarily because of overwhelming goals and climate circulation issues. In this paper, the advantages of annual solar geoengineering (ASG) to mitigate yearly global warming increases are explored and detailed as it provides higher feasibility in geoengineering applications. ASG area modification requirements found here are generally 50 to possibly higher than 150 times less compared to the challenge of full SG GW mitigation reducing circulation concerns. Results indicate that there are mixed technologies that can help meet annual mitigation Earth brightening goals. As well, results show much higher feasibility for L1 space shading compared to prior literature estimates for full GW mitigation. However, stratosphere injections appear challenging in the annual approach. Because ASG earth brightening area requirements are much smaller than those required for full mitigation, we have concerns that worldwide negative SG would interfere with making positive advances for several reasons. Negative SG currently dominates yearly practices with the application of dark asphalt roads and roofs. This issue is discussed.

PEDOT:PSS (polyethylene dioxythiophene:polystyrenesulfonate) is a commonly used hole injec-tion layer (HIL) in optoelectronic devices due to its high conductive properties and work function. However, the acidic and hygroscopic nature of PEDOT:PSS can be problematic for device stability over time. To address this issue, in this study, we have demonstrated the potential of an organic-inorganic hybrid HIL, by incorporating solution-processed WOx nanoparticles (WOx NPs) into the PEDOT:PSS mixture. This hybrid solution was found to have a superior hole transport ability and low Ohmic contact resistance, contributing to higher brightness (~62 000 cd m-2) and current efficiency (13.1 cd A-1) in the manufactured quantum-dot based light-emitting diodes (QLEDs). In addition, the resulting devices achieved a relative operational lifetime of 7,071 hours, or approxi-mately twice that of traditional QLEDs with PEDOT:PSS HILs. The proposed method is an un-complicated, reliable and low-cost way to achieve long operational lifetimes without sacrificing efficiency in optoelectronic devices.

Monte Carlo Filtering (MCF) is one of the methods of Experimental Statistical Energy Analysis (E-SEA), which allows the correction of a negative LF (Loss Factor). In this article, a modification of the MCF method, called DESA (Diagonal Extension of the Search Area), is proposed. The technique applies a non-uniform extension of the search area when generating a population of normalized energy matrices. The degree of expansion of the search area is controlled by the Diagonal Penalty Factor (DPF). The authors demonstrated the method's effectiveness on a system that could not be identified in several frequency bands by the classical MCF method. After applying DESA, it was possible to fill in the problematic bands that were missing CLF and DLF values. The paper also proposes a way to minimize the errors introduced by using overly high DPF values.

This article investigates the features of heat and mass transfer for the steady two-dimensional Williamson nanofluid flow across an exponentially stretched surface depending on suction/injection. The boundary conditions incorporate the impacts of the Brownian motion and thermophoresis boundary. The analysis of heat transfer is carried out for the two cases of prescribed exponential order surface temperature (PEST) and prescribed exponential order heat flux (PEHF). The ongoing flow problem is mathematically modeled under the basic laws of motion and heat transfer. The similarity variables are allowed to transmute the governing equations of the problem into a similarity ordinary differential equation (ODEs). The solution of this reduced non-linear system of ODEs is supported by the Homotopy analysis method (HAM). The combination of HAM arrangements is acquired by plotting the h-curve. In order to evaluate the influence of several emergent parameters, the outcomes are presented numerically and are plotted diagrammatically as a consequence of velocity, temperature and concentration proles.

Tarsal tunnel syndrome is a focal compressive neuropathy of the posterior tibial nerve or one of its associated branches. Brief mention is made in the literature of the use of corticosteroid injections for this condition. The basic technique of hydrodissection is used for other nerve entrapments and includes identifying the region of nerve compression, and the injection of a fluid medium to dissect between structures or fascial planes. We introduce our treatment protocol using a methylprednisolone/sterile water/ropivacaine hydrochloride injectate mix and peripheral nerve stimulation to a perform hydrodissection technique for tarsal tunnel syndrome.

It is important to distinguish between natural earthquakes and those induced by CO2 injection at carbon capture and storage sites. For example, the 2004 Mw 6.8 Chuetsu earthquake occurred close to the Nagaoka CO2 storage site during gas injection, but we could not quantify whether the earthquake was due to CO2 injection or not. Here we simulated changes of pore pressure during CO2 injection at the Nagaoka site and compared them with estimated natural seasonal fluctuations of pore pressure due to rainfall and snowmelt as well as estimated pore pressure increases related to remote earthquakes. We clearly distinguished changes of pore pressure due to CO2 injection from those due to rainfall and snowmelt. The simulated local increase in pore pressure at seismogenic fault area was much less than the seasonal fluctuations related to precipitation and increases caused by remote earthquakes, and the lateral extent of pore pressure increase was insufficient to influence seismogenic faults. We also demonstrated that pore pressure changes due to distant earthquakes are capable of triggering slip on seismogenic faults. The approach we developed could be used to distinguish natural from injection-induced earthquakes and will be useful for that purpose at other CO2 sequestration sites.

Carbon dioxide capture and storage (CCS) is a necessary requirement for high-emitting CO2 industries to significantly reduce volumes of greenhouse gases released to the atmosphere and mitigate the climate change. Geological CO2 storage into depleted oil and gas fields is the fastest and most accessible option for CCS deployment allowing for re-purposing of existing infrastructure and utilizing the significant knowledge about the subsurface acquired during the field production operations. Location of such depleted fields in neighbourhood of high-emitting CO2 industries is additional advantage available for matured on-shore Europe fields. Considering these advantages, the oil and gas operators are now evaluating different possibilities for CO2 sequestration projects for the fields approaching end of production. This article describes an integrated approach to reservoir simulations focused on evaluating CO2 injection pilot at one of such matured fields operated by MND and located in the Czech Republic. The potential CO2 injection site in focus is a naturally fractured carbonate reservoir. This oil-bearing formation has a gas cap at the top and a limited aquifer at the bottom of the reservoir and was produced mainly by pressure depletion with quite limited pressure support from water injection. The article summarizes results of efforts taken by the multi-disciplinary team to develop and apply an integrated approach to reservoir simulation started from geological modelling of the naturally fractured reservoir and integrating results of laboratory studies and their interpretation (geomechanical and geochemistry laboratory experiments) and dynamic field data analysis (pressure transient analysis including time-lapse) into the history matching of the reservoir model and simulations of pilot CO2 injection. Attention is given to evaluating and modelling stress-sensitive fracture properties and safe injection envelope preventing induced fracturing as well as impact of potential salt precipitation in the near wellbore area. These effects are considered in the context of pilot CO2 injection and addressed in reservoir simulations of the injection scenarios. Single porosity and permeability reservoir simulations with dominating fracture flow and black-oil formulation with CO2 simulated as a solvent were used in this study and arguments for such choice of the simulation approach for the site in focus are shortly discussed. The reservoir simulations have indicated larger site injection capacity than required for the pilot injection and allowed to evaluate CO2 migration pathway within the reservoir. The application of the approach to the site in focus has also revealed large uncertainties, related to fracture description and geomechanical evaluations, resulted in an uncertain safe injection envelope. These uncertainties should be addressed in further studies in preparation to the pilot. The article concludes with an overview of the outcomes of the integrated approach and its application to the field in focus including discussion of issues and uncertainties revealed.

Geological storage of carbon dioxide (CO2) is a crucial technology for mitigating global temperature rise. Near-depleted edge-bottom water reservoirs are attractive targets for CO2 storage, as they can not only enhance oil recovery (EOR) but also provide important potential candidates for geological storage. This study investigated CO2 enhanced oil recovery and storage for a typical near-depleted edge-bottom water reservoir that had been developed for a long time with a recovery factor of 51.93%. To improve the oil recovery and CO2 storage, new production scenarios are explored. At the near-depleted stage, by comparing the four different scenarios of water injection, gas injection, water alternating gas injection, and bi-directional injection, the highest additional recovery of 8.64% is achieved by the bi-directional injection scenario. Increasing the injection pressure leads to a higher gas-oil ratio and liquid production rate. After shifting from the near-depleted to depleted stage, the most effective approach to improve CO2 storage capacity is to increase reservoir pressure. At 1.4 times the initial reservoir pressure, the maximum storage capacity is 6.52×108 m3. However, excessive pressures boosting poses potential storage and leakage risks. Therefore, lower injection rates and longer intermittent injections are expected to achieve a larger amount of long-term CO2 storage. Through the numerical simulation study, a gas injection rate of 80,000 m3/day and a schedule of 4-6 years injection with 1 year shut-in was shown to be effective for the case considered. During 31 years of CO2 injection, the percentage dissolved CO2 increased from 5.46% to 6.23% during the near-depleted period, and to 7.76% during the depleted period. This study acts as a guide for the CO2 geological storage of typical near-depleted edge-bottom water reservoirs.

In order to explore the combustion performance of a non-road air-cooled two-cylinder turbocharged diesel engine, an experiment on the effects of engine compression ratio, combustion chamber shape and injection timing were systematically conducted in this study. Moreover, the effects of intake air conditions on combustion performance were numerically investigated using the one-dimensional simulation platform. The findings of this study could help provide new insights for promoting the sustainable development of diesel engines used in generator sets. The results show that the increase of intake air temperature can delay the combustion center of gravity, and improve the combustion performance and the sustainability of diesel engines. The decrease of intake air pressure will lead to a reduction in oxygen amount during the combustion process, thus causing a deterioration of cylinder pressure and combustion performance. By modifying the combustion chamber, the ignition delay and combustion duration are each extended by 1.6 degrees and 4.2 degrees under 100% engine load. The ignition delay and combustion duration are not obviously affected by modifying the combustion chamber shape under 25% and 50% loads. By increasing the compression ratio from 19.5 to 20.5, the ignition delay and combustion duration are shortened, which could enhance the cylinder pressure and heat release rate. However, reducing the compression ratio from 19.5 to 18.5 could significantly decrease the heat release rate. Under middle and low loads, combustion duration is less affected by injection timing. Under 100% load, the peak cylinder pressure increases to 11.4 MPa, and the ignition delay is shortened by advancing injection timing from -17°CA to -20°CA.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

The objective of this study was to investigate the liquefaction resistance of chemically improved sandy soils in a straightforward and accurate manner. Using only the existing experimental databases and artificial intelligence, the goal was to make predictions without conducting physical experiments. Emphasis was placed on the significance of data from 20 loading cycles of cyclic undrained triaxial tests to determine the liquefaction resistance and the contribution of each explanatory variable. Different combinations of explanatory variables were considered. Regarding the predictive model, it was observed that a case with the liquefaction resistance ratio as the dependent variable and other parameters as explanatory variables yielded favorable results. In terms of exploring combinations of explanatory variables, it was found advantageous to include all variables as doing so consistently resulted in a high coefficient of determination. The inclusion of the liquefaction resistance ratio in the training data was found to improve the predictive accuracy. In addition, the results obtained when using a linear model for the prediction suggested the potential to accurately predict the liquefaction resistance using historical data.

Transcutaneous injection laryngoplasty is a well-known procedure for treating paralyzed vocal fold by injecting augmentation material into it. Hence, vocal fold localization plays a vital role in the preoperative planning as the fold location is required to determine the optimal injection route. In this communication, we propose a mirror environment based reinforcement learning (RL) algorithm for localizing the right and left vocal folds in preoperative neck CT. RL-based methods commonly showed noteworthy outcome in general anatomic landmark localization problem in the recent years. However, such methods suggest training individual agent for localizing each fold, though the right and left vocal folds are located in close proximity and have high feature-similarity. Utilizing the lateral symmetry between the right and left vocal folds, the proposed mirror environment allows for a single agent for localizing both the folds by treating the left fold as a flipped version of the right fold. Thus, localization of both folds can be trained using a single training session which utilizes the inter-fold correlation and avoids redundant feature learning. Experiment with 120 CT volumes showed improved localization performance and training efficiency of the proposed method compared with the standard RL method.

We assessed if there were any sex-related differences in the ability of nicotine to increase plasma corticosterone secretion after single or repeated nicotine administration. For single-dose studies, male and female mice were habituated to the test room for 1 h and injected with saline or nicotine (0.25 or 1 mg/kg, s.c.). In repeated-dosing studies, mice were injected with saline or nicotine (1 mg/kg, s.c.) once daily for six days, and, on day 7, received nicotine (1 mg/kg, s.c.). The mice were euthanized 15 min later, and trunk blood was collected for the measurement of corticosterone, nicotine, and cotinine. Our results showed that saline or nicotine each significantly increased plasma corticosterone levels in both male and female mice, with a greater response in female mice. Plasma corticosterone levels were increased in male but not female mice after repeated compared to single nicotine administration. The level of cotinine, a biomarker of nicotine use, was significantly higher in female than in male mice. Taken together, these novel findings suggest that female mice responded to nicotine and stress of handling more than male mice and provide for the first-time quantitative data on the male-female differences in nicotine-induced elevations of corticosterone and of cotinine.

An important aspect of PET imaging in clinical application is the localization and detection of tumors and lesions by administering a predetermined amount of radiotracer. This allows for example, a detailed view of what is going inside the patient body in cellular level. The quality of PET image is strongly dependent on the amount of administrated radiotracer and the patient’s body parameters. As the amount of injection radiotracer increases, the quality of resulting image increases and the lesion detection efficiency increases. The PET examiner society recognizes that any dose of radiotracer is associated with some possible radiation risks. It can harmful to the patient if essential PET imaging session is not made due to fear of radiation risk. In order to ensure the highest quality diagnosis and the smallest radiation risk, the patient should receive the smallest amount of radiotracer that provide image with sufficient quality. Our study is focused on proposing an efficient PET simulation tool that predict the smallest possible amount of administrated radiotracer to provides the appropriate diagnostic information based on significant patient’s body parameters (weight, age) at fixed scanning to improve the clinical diagnostic process in term of tumor detecting and localization. We have built a model of particular PET scanner and model of patient based on real MRI image and digital anthropomorphic phantom of our region of interest (brain). We have performed Monte Carlo simulation for whole PET procedure with special parameter In evaluating stage, a dataset of 60 patient is used and 11 independent dose prediction simulation for each patient are performed. We conclude that our simulator perform a desirable and efficient prediction of injection radiotracer amount that optimizes the current clinical amount up to 28%. In addition, we found that the total injected radiotracer dosage for adult patients are mostly affected when considering patient weight rather than patient age.

Almost all modern inorganic light-emitting diode (LED) designs are based on double heterojunctions (DHJs) whose structure and current injection principle have remained essentially unchanged for decades. Although highly efficient devices based on the DHJ design have been developed and commercialized for energy-efficient general lighting, the conventional DHJ design requires burying the active region (AR) inside a pn-junction. This has hindered the development of emitters utilizing nanostructured ARs located close to device surfaces such as nanowires or surface quantum wells. Modern DHJ III-N LEDs also exhibit resistive losses which arise from the DHJ device geometry. The recently introduced diffusion-driven charge transport (DDCT) emitter design offers a novel way to transport charge carriers to unconventionally placed ARs. In a DDCT device, the AR is located apart from the pn-junction and the charge carriers are injected into the AR by bipolar diffusion. This device design allows the integration of surface ARs to semiconductor LEDs and offers a promising method to reduce resistive losses in high power devices. In this work, we present a review of the recent progress in gallium nitride (GaN) based DDCT devices, and an outlook of potential DDCT has for opto- and microelectronics.

Wide-bandgap tin oxide (SnO₂) thin-films are frequently used as an electron-transporting layers in perovskite solar cells due to superior thermal and environmental stabilities. However, its crystallization by conventional thermal methods requires typical temperatures between 300 and 900 ◦C [1] with up-to 60 min crystallization times. These post-processing conditions severely limit the choice of substrates and reduce the large-scale manufacturing capabilities. This work describes the intense pulsed light-induced crystallization of SnO₂ thin films using only 500 μs of exposure time. Thin-film properties are investigated using both impedance spectroscopy and photoconductivity characteristic measurements. Nyquist plot analysis establishes that the process parameters have a significant impact on the electronic and ionic behaviors of the SnO2 films. Most importantly, we demonstrate that light-induced crystallization yields improved topography and excellent electrical properties through enhanced charge transfer, improved interfacial morphology and better ohmic contacts compared to thermally-annealed SnO₂ films.

Treating central giant cell granuloma (CGCG) is challenging due to high recurrence rates and variable therapy responses. This study examines the efficacy of various treatments in reducing CGCG recurrence. A literature review explored outcomes of surgical excision, curettage, intralesional corticosteroid injection, and adjuvant therapy, considering factors like lesion location, size, and histological features. Aggressive surgical techniques such as en bloc resection were found to potentially lower recurrence rates compared to conservative approaches. However, treatment should be tailored to individual patient needs. Further research is needed to confirm these findings and improve treatment strategies. A concise literature review was conducted using PubMed, MEDLINE, and Google Scholar, focusing on papers published from 1986 to 2024. Search terms included "central giant cell granuloma," "recurrence," "treatment modalities," and "surgical excision". Studies reporting recurrence rates and treatment outcomes for CGCG were analyzed. Twenty-nine studies were reviewed, including six studies on surgical excision and curettage, eight studies on intralesional corticosteroid injections, six studies on calcitonin therapy, five studies on interferon alpha therapy and four studies on the therapy with denosumab. Analysis indicated that aggressive surgical treatments like en bloc resection were associated with lower recurrence rates compared to conservative methods. Predictors of recurrence included lesion size (&gt;3 cm), location (mandible), and aggressive histopathological features. Aggressive surgical excision combined with nonsurgical methods may lower recurrence rates, while conservative techniques remain viable in some cases. Further prospective research is needed to validate these findings and enhance CGCG treatment options.

Backgorund and Objectives: In this study, we aimed to evaluate and compare the changes in visual and structural outcomes in patients with intravitreal aflibercept (IVA)-resistant neovascular age-related macular degeneration (nAMD) switched to either intravitreal brolucizumab (IVBr) or intravitreal faricimab (IVF) injections in a clinical setting. Materials and Methods: This obser-vational clinical study included 20 eyes of 20 patients switched to brolucizumab and 15 eyes of 14 patients switched to faricimab for aflibercept-resistant nAMD. We measured the structural outcome (central macular thickness (CMT)) and the visual outcome (best-corrected visual acuity (BCVA); logMAR) as follows: just before the most recent IVA injection (B0), one month after the most recent IVA injection (B1), just before the first IVBr or IVF injection (A0), one month after (A1) and three months after (A3) the first IVBr or IVF injection. Results: BCVA showed significant im-provement at A1 (0.25 ± 0.34) and at A3 (0.19 ± 0.24) compared to A0 (0.38 ± 0.35) in IVBr group (p = 0.0156, p = 0.0166, respectively). CMT (μm) was significantly thinner at A1 (IVBr; 240.55 ± 51.82, IVF; 234.91 ± 47.29) and at A3 (IVBr; 243.21 ± 76.15, IVF; 250.50 ± 72.61) compared to at A0 (IVBr; 303.55 ± 79.18, IVF; 270.33 ± 77.62) in IVBr group (A1; p = 0.0093, A3; p = 0.0026) and in IVF group (A1; p = 0.0161, A3; p = 0.0093). There was no significant difference in BCVA and CMT improvement observed between two groups at any time point (p > 0.05 for all). Conclusion: Switching from aflibercept to either brolucizumab or faricimab has a significant anatomical ef-fect on eyes with aflibercept-resistant nAMD and both treatments appear to be effective short-term treatment options. There is a trend towards greater visual improvements and reductions in CMT with brolucizumab.

Background: Endogenous Candida endophthalmitis (ECE) is a rare but sight-threatening disease. Patients with ECE present with various clinical signs and symptoms, which can complicate the diagnosis. The aim of this report was to describe the characteristic features of ECE on optical co-herence tomography (OCT) and OCT angiography (OCTA). Another objective was to demon-strate the outcomes of treatment and to diagnose macular complications caused by intraocular inflammation. Case presentation: A 41-year-old woman with a history of acute intermittent por-phyria presented with a progressive vision loss in her left eye. Left-eye OCT revealed findings consistent with a fungal etiology, which was confirmed by the culture of swabs collected from a central vein catheter. The outcomes of intravenous fluconazole treatment were not satisfactory, and the patient developed recurrent attacks of porphyria, suggesting a porphyrogenic effect of systemic antifungal therapy. Repeated intravitreal injections with amphotericin B led to a gradu-al regression of inflammatory lesions. However, follow-up examinations revealed active macular neovascularization on both OCT and OCTA. The patient was administered intravitreal bevaci-zumab. Conclusions: This case highlights the importance of OCT and OCTA as valuable noninva-sive imaging techniques for the identification of ECE, the monitoring of its clinical course, and the diagnosis of macular complications.

Gas turbine power plants have important roles in the global power generation market. The examines thermodynamically the impact of steam injection for a combined cycle including a gas turbine cycle with a two-stage turbine and carbon dioxide recompression. The combined cycle is compared with the simple case without steam injection. Steam injection’s impact is observed on important parameters such as energy efficiency, exergy efficiency, and output power. It is revealed that steam injection reduces exergy destruction in components compared to the simple case. The efficiencies for both cases are obtained. The energy and exergy efficiencies respectively are found to be 30.4% and 29.4% for the simple case, and 35.3% and 34.1% for the case with steam injection. Also, incorporating steam injection reduces emissions of carbon dioxide.

Approximately 2 TCF (Trillion Cubic Feet) of acid gas are projected to be injected into the Surmeh formation. The recommended injection rate is 180 MMSCFD (Million standard cubic feet per day), based on acid gas content and gas in place of the source of injection. The tight nature of the Surmeh formation limits injectivity, with a maximum achievable rate of 7 MMSCFD for permeability of 1 mD (millidarcy). However, higher porosity (12%) and permeability of 100 mD enable more efficient injection without fracturing the formation. This study provides valuable insights into the feasibility of AGI in saline aquifers, emphasizing reservoir characterization, geomechanics, caprock integrity, and rock properties. The findings contribute to the implementation of environmentally sustainable acid gas disposal at offshore reservoirs.

This paper presents a study aimed at enhancing the performance of quantum dot light-emitting didoes (QLEDs) by employing a solution-processed molybdenum oxide (MoO3) nanoparticle (NP) as a hole injection layer (HIL). The study investigates the impact of varying the concentrations of the MoO3 NP layer on device characteristics and explores the underlying mechanisms responsible for the observed enhancements. Experimental techniques such as an X-ray diffraction and field-emission transmission electron microscopy were employed to confirm the formation of MoO3 NPs during the synthesis process. Ultraviolet photoelectron spectroscopy is employed to analyze the electron structure of the QLEDs. The QLED with an 8 mg/mL concentration of MoO3 nanoparticles achieves remarkable improvements in device performance, with a maximum luminance of 69,240.7 cd/cm2, maximum current efficiency of 56.0 cd/A, and maximum external quantum efficiency (EQE) of 13.2%. The obtained results signify a notable progress in comparison to QLED without HIL and those utilizing the widely used poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) HIL. They exhibit a remarkable enhancement of 59.5% and 26.4% in maximum current efficiency, respectively, as well as a significant improvement of 42.7% and 20.0% in maximum EQE, respectively. This study opens up new possibilities for the selection of HIL and the fabrication of solution-processed QLEDs, contributing to the potential commercialization of these devices in the future.

Given the global economic and societal importance of the polymer industry, the continuous search for improvements in the various processing techniques is of practical primordial importance. This review evaluates the application of optimization methodologies to the main polymer processing operations. The most important characteristics related with the usage of optimization techniques, such as the nature of the objective function, the type of optimization algorithm, the modelling approach used to evaluate the solutions, and the parameters to optimize, are discussed. The aim is to identify the most important features of an optimization system for polymer processing problems, and define the best procedure for each particular practical situation. For this purpose, a state-of-the-art of the optimization methodologies usually employed is first presented, followed by an extensive review of the literature dealing with the major processing techniques, the discussion being completed by considering both the characteristics identified and the available optimization methodologies. This first part of the review focus on extrusion, namely extruders, extrusion dies and calibrators. It is concluded that there is a set of methodologies that can be confidently applied in polymer processing, with a very good performance and without the need of demanding computation requirements.

In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. Without changing the oil displacement capability of high molecular weight ASP solution in high permeability oil layers, the ASP solution is actively sheared in low permeability oil layers by using a partial quality tool to increase the injection capability of the solution and improve the overall oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, firstly, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.

Supplier selection is one of the most important multi criteria decision making (MCDM) problems for decision makers in competitive market. Organizations of today’s world are seeking new ways to reduce negative effects of their organizations to the environment and to reach a greener system. At this point, green supplier selection concept has gained great importance with its ability on incorporating environmental or green criteria into the classical supplier selection practices. Therefore, in this study, it is aimed at proposing a multi-phase MCDM model based on Best-Worst Method (BWM) and interval type-2 fuzzy technique for order preference by similarity to ideal solution (TOPSIS). A case study in a plastic injection molding facility in Turkey is performed to show the applicability of the proposed integrated methodology. The paper ensures insights into the decision making, methodology, and managerial implications. Results of the case study are examined and suggestions for future research are provided.

Using Internet of Things (IoT) applications has been a growing trend in the last few years. They have been deployed in several areas of life including secure and sensitive sectors like military and health. In these sectors, sensory data is the main factor in any decision-making process. This introduces the need to ensure the integrity of data. Secure techniques are needed to detect any data injection attempt before catastrophic effects happen. Sensors have limited computational and power resources. This limitation creates a challenge to design a security mechanism that is both secure and energy-efficient. This work presents a Randomized Watermarking Filtering Scheme (RWFS) for IoT applications that provides en-route filtering to get rid of any injected data at an early stage of the communication. Filtering injected data is based on a watermark that is generated from the original data and embedded directly in random places throughout the packet's payload. The scheme uses homomorphic encryption techniques to conceal the report's measurement from any adversary. The advantage of homomorphic encryption is that it allows the data to be aggregated and, thus, decreases the packet's size. The results of our proposed scheme proved that it improves the security and energy consumption of the system as it mitigates some of the limitations in the existing works.

Septic arthritis (SA) represents an orthopedics urgency and mainly affects the knee joint. Due to its devastating effects on cartilage, immediate management is crucial. SA is characterized by an an-nual incidence of 2 to 10 cases per 100,000 individuals, with mortality rates fluctuating between 0.5% and 15%, with a substantially higher mortality rate observed in older people (15%) in con-trast to younger cohorts (4%). The etiology of septic arthritis is multifactorial: a spectrum of Gram-positive and Gram-negative bacteria can contribute to the development of this condition, especially Staphylococcus aureus. The treatment involves urgent (arthroscopic or arthrotomic) debridement associated with adequate antibiotic therapy. Intra-articular antibiotic carriers can also be used to increase their local concentration and effectiveness. The case of a 67-years-old woman affected by knee SA from methicillin-susceptible S. aureus is presented. She was treated with an arthroscopic debridement enhanced by intra-articular antibiotic-loaded calcium sulphate beads, together with antibiotic therapy. At 2-year follow-up, the infection has been eradicated and the patient fully recovered. This is the first description, to our knowledge, in English Literature of the use of antibiotic-loaded calcium sulphate beads as an adjuvant in the surgical treatment of SA of a native knee joint.

Zn_0.9Mg_0.1O nanoparticle (NP) were employed as electron transport layers (ETLs) with varying thicknesses to investigate their influence on the efficiency of the top-emission quantum dot light-emitting diodes (TE-QLEDs) fabricated inside the bank. An increase in the thickness of the Zn_0.9Mg_0.1O NP ETL led to a decrease in the concentration of oxygen vacancies, reducing the conductivity of the Zn_0.9Mg_0.1O and resulting in lower current density in the TE-QLEDs. The decrease in conductivity of Zn_0.9Mg_0.1O NP ETL was confirmed through electron-only device (EOD) characterization. Furthermore, it was noted that when the thickness of Zn_0.9Mg_0.1O NP ETL was 30 nm, the concentration of hydroxyl species reached its minimum. By minimizing the presence of hydroxyl species, exciton quenching at the quantum dot (QD) and Zn_0.9Mg_0.1O NP ETL interface was minimized, enhancing charge balance within the QD, significantly improving the efficiency of QLED. We successfully demonstrated that TE-QLED with a 30 nm-thick Zn_0.9Mg_0.1O NP ETL exhibits outstanding performance, achieving a maximum current efficiency of 91.92 cd/A and a maximum external quantum efficiency of 21.66%. These results suggest that Zn_0.9Mg_0.1O NP ETL, when tailored to an appropriate thickness, can serve as an ETL for TE-QLEDs, effectively suppressing exciton quenching and enhancing the charge balance in the TE-QLEDs.

Numerous reservoirs that play a significant role in worldwide petroleum production and reserves contain fractures. Typically, the fractures must form a connected network for a reservoir to be classified as naturally fractured. Characterizing the reservoir with a focus on its fracture network is crucial for modeling and predicting production performance. To simplify the solution, dual continuum modeling techniques are commonly employed. However, to use continuum-scale approaches, properties such as average aperture, permeability, and matrix fracture interaction parameters must be assigned, making it necessary to improve fracture depiction and modeling methods. This study investigates a fractured reservoir with a low matrix permeability and a well-connected fracture network. The focus is on the impact of the hyrachical fracture network on the production performance of gas-based enhanced oil recovery methods. The Discrete Fracture Model (DFN) was utilized to create comprehensive two-dimensional models for three processes: Gas Injection (GI), Water Alternating Gas (WAG), and Foam Assisted Water Alternating Gas (FAWAG). Moreover, dimensionless numbers were employed to establish connections between properties across the entire fracture hierarchy, spanning from minor to major fractures and encompassing the fracture intensity. The results indicate that the FAWAG is more sensitive to fracture types and networks than the WAG and GI processes. Hence, the sensitivity of the individual EOR method to the fracture network requires a respective depth of description of the fracture network. However, other factors, such as reservoir fluids properties and fracture properties, might influence the recovery when the minor fracture networks are excluded. This study has determined that, among the enhanced oil recovery (EOR) techniques examined, the significance of the hyrachical depth of fracture networks diminishes as the ratio of major (primary fracture) aperture to the aperture of medium and minor fractures increases. Additionally, the impact of the assisted-gravity drainage method was greater with increased reservoir height; however, as the intensity ratio increased, the relative importance of medium and minor fracture networks decreased.

Objective: This systematic review and meta-analysis compared the patient-reported outcomes of intra-articular facet joint injections of normal saline and selected active substances to identify a more effective agent for treating subacute and chronic low back pain (LBP). Methods: The PubMed, Embase, Scopus, Web of Science, and CENTRAL databases were searched for randomized controlled trials and observational studies published in English. A research quality assessment was performed using ROB2 and ROBINS-I. A meta-analysis was conducted using a random-effects model, and the mean differences (MD) with 95% confidence intervals (CI) in efficacy outcomes, including pain, numbness, disability, and quality of life, were assessed. Results: Of the 2,467 potential studies, three were included (247 patients). The active substances and normal saline had similar therapeutic effects on pain within 1 h, after 1-1.5 months, and after 3-6 months, with MD and 95% CI of 2.43 and -11.61 to 16.50, -0.63 and -7.97 to 6.72, and 1.90 and -16.03 to 19.83, respectively, as well as the quality of life after 1 and 6 months. Conclusion: The short- and long-term clinical effects of intra-articular facet joint injections of normal saline are comparable to those of other active substances in patients with LBP.

Introduction. A needle is inserted into a joint for arthrocentesis or injection of a therapeutic medication(s), commonly a corticosteroid. The aim of this paper is to discuss the first theme identified from a scoping review of corticosteroid injections for the pathology of the first metatarsophalangeal joint. Pathology. The two most common pathologies affecting the first metatarsophalangeal joint are osteoarthritis and bunions. An arthritic joint is regularly injected with a corticosteroid, but bunions are not. Other pathologies that may receive an injection include rheumatoid arthritis, gout, sesamoiditis and post-operative arthrofibrosis. Discussion. Most available evidence discusses corticosteroid injections for osteoarthritis, but there is a paucity of high-quality evidence, especially for corticosteroid use in other pathological conditions. Conclusion. Whilst the evidence base suggests that corticosteroid injections are safe short- and mid-term treatment options for a range of soft tissue and joint pathology, the specific indications, and short/long-term outcomes in the first metatarsophalangeal joint pathologies are not clear and warrant further study.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

Over the past few years, the importance of video surveillance in securing the national critical infrastructure has significantly increased, whose applications include detecting failures and anomalies. Accompanied by video proliferation is the increasing number of attacks against surveillance systems. Among the attacks, false frame injection (FFI) attacks that replay video frames from a previous recording to mask the live feed has the highest impact. While many attempts have been made to detect FFI frames using features from the video feeds, video analysis is computationally too intensive to be deployed on-site for real-time false frame detection. In this paper, we investigate the feasibility of FFI attacks on compromised surveillance systems at the edge and propose an effective technique to detect the injected false video and audio frames by monitoring the surveillance feed using the embedded Electrical Network Frequency (ENF) signals. An ENF operates at a nominal frequency of 60 Hz/50 Hz based on its geographical location and maintains a stable value across the entire power grid interconnection with minor fluctuations. For surveillance system video/audio recordings connected to the power grid, the ENF signals are embedded. The time-varying nature of the ENF component is used as a forensic application for authenticating the surveillance feed. The paper highlights the ENF signal collection from a power grid creating a reference database and ENF extraction from the recordings using conventional short-time Fourier Transform and spectrum detection for robust ENF signal analysis in the presence of noise and interference caused in different harmonics. The experimental results demonstrate the effectiveness of ENF signal detection and/or abnormalities for FFI attacks.

Heavy Ion Beam Probing (HIBP) diagnostic is a powerful tool for electric field studies in hot dense plasma of modern day toroidal magnetic confinement devices. On the TUMAN-3M to-kamak, the HIBP have been used in regimes with improved plasma confinement to clear up the role of radial electric field in the transition to good confinement regimes. Recently, a moderni-zation of the TUMAN-3M HIBP diagnostics was performed aiming to reconfigure it for a work with a reversed plasma current direction and improvement of overall stability of the diagnostic. The results of first measurements of plasma potential in co-NBI scenario are reported and dis-cussed.

We use Matlab 3D finite element fluid flow/transport modelling to simulate localized wellbore temperature events of order 0.05-0.1oC logged in Fennoscandia basement rock at ~ 1.5km depths. The temperature events are approximated as steady-state heat transport due to fluid draining from the crust into the wellbore via naturally occurring fracture-connectivity structures. Flow simulation is based on the empirics of spatially-correlated fracture-connectivity fluid flow widely attested by well-log, well-core, and well-production data. Matching model wellbore-centric radial temperature profiles to a 2D analytic expression for steady-state radial heat transport with Peclet number Pe ≡ r0φv0/D (r0 = wellbore radius, v0 = Darcy velocity at r0, φ = ambient porosity, D = rock-water thermal diffusivity), gives Pe ~ 10-15 for fracture-connectivity flow intersecting the well, and Pe ~ 0 for ambient crust. Darcy flow for model Pe ~ 10 at radius ~ 10 meters from the wellbore gives permeability estimate κ ~ 0.02Darcy for flow driven by differential fluid pressure between least principal crustal stress pore pressure and hydrostatic wellbore pressure. Model temperature event flow permeability κm ~ 0.02Darcy is related to well-core ambient permeability κ ~ 1µDarcy by empirical poroperm relation κm ~ κ exp(αmφ) for φ ~ 0.01 and αm ~ 1000. Our modelling of wellbore temperature events calibrates the concept of reactivating fossilized fracture-connectivity flow for EGS permeability stimulation of basement rock.

To evaluate the efficacy of percutaneous dilatational tracheostomy (PDT) combined with adjuvant therapies in preserving vocal function in amyotrophic lateral sclerosis (ALS) patients. Methods: We performed a retrospective analysis of 47 ALS patients who underwent PDT at the Rodem Hospital from 2021 to 2023. Post-operatively, these patients were provided with a comprehensive treatment plan that included regenerative injection therapy, low-frequency electrical stimulation, respiratory rehabilitation, and swallowing rehabilitation therapy. Additionally, a balloon reduction program was implemented for effective Tracheostomy tube (T-tube) management. The preservation of vocal functions was evaluated 4 weeks following the procedure. Results: While some patients maintained or slightly improved their ALSFRS-R speech scores, the overall trend indicated a de-crease in speech scores post-PDT. This suggests that PDT combined with adjuvant therapies may not universally improve vocal function, but can help maintain it in certain cases. Conclusion: Our findings indicate that PDT combined with mesotherapy, low-frequency electrical stimulation, and swallowing rehabilitation therapy may play a role in maintaining vocal function in limb type ALS patients, though further research is needed to optimize patient management and validate these results.

In order to enhance the gain of antenna suitable for the airplane mounted platform, a conformal tightly coupled antenna array is investigated in this paper. Especially, three-dimensional (3-D) inkjet printing technique is used to implement the conformal property. The printing of antenna substrate and radiation layer is implemented by combining the fused deposition modelling and microdroplet injection molding technologies based on the existing 3-D printer. Here, through a unique combination of 3-D and 2-D inkjet printing of dielectric material and metallic ink, respectively, we demonstrate a monolithically integrated to a nonplanar antenna for the first time. Antenna measurements show that the complete characterization of this new process in terms of minimum feature sizes and achievable conductivities. This antenna configuration offers a high-gain performance with low-cost and rapid fabrication technique by using 3-D printing. The voltage standing wave ratio and radiation patterns are tested after adding the newly designed feed structure. Results shown the design process much efficient. Both antenna element and the array with good properties, which are in very good agreement with the specially mounted platform.

Background: We assess locoregional drug targeting effectiveness of intraoperative (IO) cryoprobe-assisted injection of blue dye (BD) and cytotoxic-tracer mixture (TTM), in VX2 tumor model, and its translational value to cryo-assisted breast tumor surgery with BD alone. Methods: Under computed tomography (CT) guidance, we injected two ml TTM in five aliquots in the margin of 16 frozen or normothermic VX2 tumors. We evaluated the IO and post-operative drug targeting and therapeutic efficacy in tumor-host interface (T-HI) by CT, gross examination, and histopathology. In twenty-six T1 to T4 primary breast cancer (BRCA) we performed ultrasound-guided (US) cryoprobe-assisted tumor freezing, BD guided lymphatic mapping, and surgery. We evaluated, IO and in freshly resected specimen, BD distribution pattern in T-HI, lymph node(s), breast parenchyma, and resection cavity. Results: Fluids-impervious frozen VX2 or breast tumor transported drug(s) an arc-like pattern at T-HI regardless of freeze dose, number of freeze-thaw cycles, drug dose fractionation, tumor characteristics or dimensions. During melting, TTM spread within fifty percent VX2 tumor mirrored that of T-HI; it was massive in normothermia. In VX2 twenty percent focal margin necrosis at pathology coincided with CT gap; in both studies, BD dose-staining spread in T-HI and tumor was linear. Eighty-four patients had one to twelve stained axillary lymph nodes; sixty-nine percent and all respectively, had another quadrant and resection cavity stained. Conclusion: Intraoperative freezing-assisted drug delivery and targeting techniques during cryoablation of VX2 tumor translate successfully to locoregional BD targeting, lymphatic mapping during cryo-assisted surgery of breast cancer.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

The subject of the conducted study was focused on the development of new type of technical blends reinforced with natural fillers. The study was divided into two parts, where in the firsts stage of the research unmodified POM was reinforced with different types of natural fillers: cellulose, wood flour and husk particles. In order to select the type of filler intended for further modification, the mechanical characteristics was assessed. The 20% wood flour (WF) filler system was selected as the reinforcement. The second stage of research involved the use of combination of polyoxymethylene POM and poly(lactic acid) PLA. POM/PLA blend (ratio 50/50 %) were modified with elastomeric compound (EBA) and chain extender as reactive compatibilized (CE). The microscopic analysis revealed that for POM/PLA system the filler-matrix interface is characterized by better wettability, which might suggest higher adhesion. The mechanical performance revealed that for POM/PLA-based composites the properties were very close to the results for POM-WF composites; however, there is still large difference in thermal resistance in favor of POM-based materials. The increase in thermomechanical properties for POM/PLA composites occurs after heat treatment. The increasing crystallinity of the PLA phase allows for an significant increase of the head deflection temperature (HDT), even above 125 °C.

Neutral beam injection (NBI) is used for thermonuclear plasma heating, non-inductive current drive, rotation, operation scenario control, and for plasma diagnostics in nuclear fusion devices. NBI is the main source of fast particles in plasma which transmit energy to thermal plasma during their slow-down. Steady-state tokamak operation is only possible when the sub-thermal particles energy is absorbed and effectively confined in plasma volume. While NBI purposes and applications vary through different fusion systems, the engineering tasks performed during research and development (R&D) stage of neutral beamline design have much in common. The NBI studies, especially addressing long pulse and high-power operation typically include a beam transmission analysis and power loads distribution at the structural components of the beamline. Thermo-structural analysis is applied next to heat removal circuits design. ‘Beam Transmission’ (BTR) code is a dedicated tool, developed by a physicist and used by NBI physicists and engineers. BTR was created and 1^st applied during R&D phase of the world’s largest tokamak ITER. BTR code is intended for public usage and routinely applied for detailed simulations of neutral beam propagation through complex beamlines. BTR is flexible and intuitive in input, user-friendly and fully interactive. Thanks to visualization and high performance BTR looks and feels like a real NB flight simulator. Despite BTR ‘mature’ age, the code is still in evolution. Support is available to all new BTR users.

SQL injection attacks are one of the most common types of attacks on web applications. These attacks exploit vulnerabilities in the application’s database access mechanisms, allowing attackers to execute unauthorized SQL queries. In this study, we propose an architecture for detecting SQL injection attacks using a recurrent neural network (RNN) autoencoder. The proposed architecture was trained on a publicly available dataset of SQL injection attacks. Then compared with several other machine learning models, including ANN, CNN, Decision Tree, Naïve Bayes, SVM, Random Forest, and Logistic Regression. The experimental result showed that the proposed approach achieved an accuracy of 94% and an F1 score of 92%, which demonstrate its effectiveness in detecting QL injection attacks with high accuracy in comparison with other models covered in the study.

Despite the fact that strong routine separation methodologies can give reliable specificity and validity at usual working pharmaceuticals concentrations, they may fail at very low concentration levels. This poses considerable challenges for researchers inves-tigating product purity and therapeutic drug monitoring. Sensitivity enhancement pro-cedures are thus required to maximize the performance of separation techniques. Large volume injection, solid phase extraction/solid phase enrichment (SPE/SPEn), pre-, post-, and in-column derivatization, as well as the use of sensitive detection devices are the simplest strategies for improving sensitivity of the separation-based analytical techniques. Large volume injection of samples with online SPE/SPEn coupled with separation techniques increased sensitivity and improved detection as well as quantification limits without affecting peak shape and system performance. Although the primary purpose of derivatization is to improve sensitivity and selectivity, greener derivatization is growing in popularity and should be considered in analytical chemistry. In general, two strategies are essential for accomplishing greener derivatization goals. The first is the search for and use of ecologically acceptable derivatizing reagents, solvents, and reaction conditions. The second is miniaturization and automation of analytical methods. This review discusses significant advances in separation-based analytical techniques, specifically enrichment approaches and detector signal improvement for pharmaceutical quantification in various matrices at very low concentration levels. As a result of improved analytical systems setup in drug assays, the possibility of high-throughput analyses was also highlighted.

We present a novel passive satellite remote sensing approach for observing the three-dimensional distribution of aerosols emitted from wildfires. This method, called AEROS5P, retrieves vertical profiles of aerosol extinction from measurements of the TROPOMI satellite sensor onboard the Sentinel 5 Precursor mission. It uses a Tikhonov-Phillips regularization which iteratively fits cloud-free near-infrared and visible selected reflectances to simultaneously adjust the vertical distribution and abundance of aerosols. The information on the altitude of the aerosol layers is provided by TROPOMI measurements of the reflectance spectra at the oxygen A-band near 760 nm. In the present paper, we use this new approach for observing the daily evolution of the three-dimensional distribution of biomass burning aerosols emitted by Australian wildfires on 20-24 December 2019. Aerosol optical depths (AOD) derived by vertical integration of the aerosol extinction profiles retrieved by AEROS5P are compared with MODIS, VIIRS and AERONET coincident observations. They show a good agreement in the horizontal distribution of biomass burning aerosols, with a correlation coefficient of 0.86 and a mean absolute error of 0.2 with respect to VIIRS. A fair agreement is found between coincident transects of vertical profiles of biomass burning aerosols derived from AEROS5P and from the CALIOP spaceborne lidar. The mean altitude of these aerosols derived from these two measurements show a good agreement, with a small mean bias (185 m) and a correlation coefficient of 0.83. Moreover, AEROS5P observations reveal the height of injection of the biomass burning aerosols in 3D. The highest injection heights during the period of analysis are coincident with the largest fire radiative power derived from MODIS. Consistency is also found with respect to the vertical stability of the atmosphere.

In today's technologically advanced landscape, sensors feed critical data for accurate decision-making and actions. Ensuring the integrity and reliability of sensor data is paramount to system performance and security. This paper introduces an innovative approach utilizing discrete wavelet transforms (DWT) embedded within microcontrollers to scrutinize sensor data meticulously. Our methodology aims to detect and isolate malfunctions, misuse, or any anomalies before they permeate the system, potentially causing widespread disruption. By leveraging the power of wavelet-based analysis, we embed computational intelligence directly into the microcontrollers, enabling them to monitor and validate their outputs in real-time. This proactive anomaly detection framework is designed to distinguish between normal and aberrant sensor behaviors, thereby safeguarding the system from erroneous data propagation. Our approach significantly enhances the reliability of embedded systems, providing a robust defense against false data injection attacks and contributing to overall cybersecurity.