The aeroelastic response of lightweight low-speed aircraft with slender wings under extreme flow turbulence intensity is not well-understood. Experiments on a commmercial unmanned aerial vehicle (UAV) with a 3-meter wingspan and aspect ratio of 13.6 were performed in a large open-return wind tunnel with extreme flow turbulence intensity of T∞≈10%. The structural dynamics of the wing in the bending mode and the flow beneath the wing to capture the effect of aileron deflection was measured using laser displacement sensors and tomographic particle image velocimetry (PIV) techniques. The unsteady lift produced by the wing was also measured using a high-capacity load cell at an angle of attack, α of 2 degrees for three freestream velocities U∞ of 13.4 m/s, 17.9 m/s, and 26.8 m/s representing the UAV’s stall through cruise speed. It was found that high flow turbulence intensity with large integral length scales relative to the wing chord plays a dominant role in the large unsteady lift and wing displacements measured. The power spectral density (PSD) of wing structural vibration shows that flow shedding from the wing and the integral length scales have a significant impact on the overall power inherent in the bending vibration of the wing. Computation of vorticity iso-surfaces in the flow measurement volume surrounding the aileron reveal a striking observation; aileron deflection, δa of 10∘becomes less effective in producing additional spanwise vorticity, which is proportional to circulation and lift, at U∞ of 26.8 m/s because the freestream already has elevated levels of vorticity. A paradigm shift in design is suggested for light aircraft structures with slender wings operating in highly turbulent flow, which is to employ multiple control surfaces in order to respond to this flow and mitigate large bending or torsion displacements and the probability of structural failure.

Bandsaw blades are typical band-shaped cutting tools characterized by a low stiffness and micro-level cutting depth, resulting in distinct wear mechanisms compared to rigid cutting tools. In this study, the evolution of bandsaw tooth wear mechanisms during the bandsawing of Cr12MoV cold-working steel was investigated. The tool life was divided into two stages according to the tooth wear mechanism: a rapid wear stage (Stage I) and a homogeneous wear stage (Stage II). In Stage I, the wear mechanism was dominated by chipping, although multiple wear mechanisms were found because of the relatively poor manufacturing tolerance compared to rigid cutting tools, resulting in remarkable differences between the cutting depths of the individual teeth. In Stage II, abrasive and adhesive wear were the primary wear mechanisms instead of chipping, due to the decreased width and setting magnitude tolerance after Stage I. Furthermore, methods for increasing the bandsaw performance were proposed based on the tooth wear mechanisms.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

Carbonization of a biopolymer (lignin) in self-propagating high-temperature synthesis (SHS) led to the production of 2D graphene structures. With the help of modern analytical methods (Raman spectroscopy, X-ray diffraction) and electron microscopy, the resulting product was confirmed to have a few-layer 2D graphene structure. The predicted photovoltaic properties of the resulting few-layer graphene were implemented for laser ignition of a model pyrotechnic composition based on porous silicon. A phenomenological model of the formation mechanism of 2D graphene structures under the conditions of the SHS process is proposed.

A twin-screw extruder was used to fabricate poly(butylene succinate) (PBS)/high density polyethylene (HDPE) blends (7:3 weight ratio) and blend-based nanocomposites. Carbon nanotubes (CNTs), graphene nanoplatelets (GNPs) and organoclays (15A and 30B) served as the nanofiller, while maleated HDPE (PEgMA) acted as an efficient compatibilizer for the blend. In the composites, individual nanofillers were mostly localized in HDPE domains, but some fillers were also observed at PBS-HDPE interfaces. The sea-island morphology of compatibilized blend evolved into a pseudo-co-continuous morphology in the composites. Differential scanning calorimetry results confirmed that PEgMA with HDPE evidently accelerated the crystallization of PBS in the blend. The possible nucleation effect of added fillers on PBS crystallization was obscured by the formation of quasi-connected HDPE domains, causing less PBS nucleation sites. The presence of nanofillers improved the thermal stability and burning anti-dripping behavior of the parent blend. The anti-dripping efficiency of added fillers followed the sequence: CNT>15A>30B>GNP. Rigidity of the blend was increased after formation of nanocomposites. In particular, adding GNP resulted in 31% increase in flexural modulus. Development of a pseudo-network structure in the composites was confirmed by measurement of rheological properties. Electrical resistivity of the blend was reduced by more than 6 orders of magnitude at 3 phr CNT loading, demonstrating the achievement of double percolation morphology.

Ornamental kale (Brassica oleracea var. acephala) is an attractive ornamental plant with a range of leaf colors and shapes. Breeding new varieties of ornamental kale has proven challenging due to its lengthy breeding cycle and the limited availability of genetic markers. Microspore culture is an effective approach to generate new materials and genetic maps are a prerequisite for quantitative trait loci analysis, MAS, fine gene mapping, and genome sequence assembly. In this study, a F1DH ornamental kale population comprising 300 DH lines was constructed using microspore culture. A high-density genetic map was developed by conducting whole-genome sequencing on 150 individuals from the F1DH population. The genetic map contained 1,696 bin-markers with 982,642 single-nucleotide polymorphisms (SNPs) spanning a total distance of 775.81 cM on all nine chromosomes with an average distance between markers of 0.46 cM. The ornamental kale genetic map contained substantially more SNP markers compared with published genetic maps for other B. oleracea crops. The F1DH progenies provide an excellent resource for germplasm innovation and breeding new varieties of ornamental kale. The high-density genetic map provides crucial insights for gene mapping and unraveling the molecular mechanisms behind important agronomic traits in ornamental kale.

A 4×2 factorial experiment was conducted to evaluate the potential of feeding dietary gamma-oryzanol and vitamin E tocotrienols in hens reared in 840 (low cage density; LCD) or 420 cm2/hen (high cage density; HCD). A total of 120 hens were allocated into eight groups with five replicates. Diets were a control (CON) or the control diet supplemented with 200 ppm gamma-oryzanol (GO-200), 200 ppm vitamin E tocotrienols (VE-200) or 200 ppm gamma-oryzanol + 200 ppm vitamin E tocotrienols (GE-400). Results showed that HCD-housed hens decreased (P &lt; 0.01) egg performance and quality. Average egg weight (AEW), egg mass and FCR improved in all supplemented treatments. Results on the AEW, FCR, and eggshell qualities of birds kept at the HCD revealed the best responses in the GE-400 group (P &lt; 0.01). Among hens kept on an HCD, there was a noticeable decrease in HMGCR mRNA abundance in the VE-200 group, while the highest IFN-γ mRNA abundance was found in hens fed the GO-200 diet (P &lt; 0.05). Thus, this study suggested that dietary GO or VE at 200 ppm either individually or in combination could improve performance and egg quality as well as regulate the abundance of immune- and stress-related genes.

Staphylococcus aureus is a common pathogen in human. Methicillin resistant Staphylococcus aureus (MRSA) infection poses a big and perplexing difficulty in terms of therapy. The acquisition of the non-native gene PBP2a, which has a decreased tolerance for β-lactam antibiotics, frequently confers resistance. PBP2a has a less attraction for methicillin and it helps bacteria to continue peptidoglycan biosynthesis, and it is cell wall’s core component in bacteria. So, even in the presence of methicillin or any other antibiotic, bacteria develop resistance. Due to resistance-causing genes, S. aureus becomes MRSA. The main premise of the resistance mechanism is well understood. The current demand for novel antibiotics is legitimate in the face of therapeutic concerns posed by resistant micro-organisms. The emphasis of this review is on PBP2a scaffolds and the different screening approaches used to find PBP2a inhibitors. Penicillin, Cephalosporins, Pyrazole-Benzimidazole based derivatives, Oxadiazole containing derivatives, non-β-lactam allosteric inhibitors, 4-(3H)-Quinazolinones, Pyrrolylated chalcone, Bis-2-Oxoazetidinyl macrocycle (β-lactam antibiotics with 1, 3-Bridges), Macrocycle-embedded β-lactams as novel inhibitors, Pyridine-Coupled Pyrimidinones, novel Naphthalimide corbelled aminothiazoximes, non-covalent inhibitors, Investigational-β-lactam antibiotics Carbapenem, novel Benzoxazole derivatives, Pyrazolylpyridine analogues, and other miscellaneous classes of scaffolds for PBP2a are also represented as well as with their biological activity is discussed. The penicillin-binding protein is also discussed, which is the crucial target for the cell wall of MRSA. Various aspects of PBP2a, the cell wall of bacteria, peptidoglycans, different crystal structures of PBP2a, synthetic routes for PBP2a inhibitors, and future perspectives of MRSA inhibitors are also enumerated.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

High-grade gliomas present a significant challenge in neuro-oncology because of their aggressive nature and resistance to current therapies. Boron neutron capture therapy (BNCT) is a potential treatment method; however, the boron carrier compounds used — such as 4-borono-L-phenylalanine (L-BPA) — have limitations. This study evaluated the use of boron-conjugated 4-iodophenylbutanamide (BC-IP), a novel boron compound in BNCT, for the treatment of glioma. Using in vitro drug exposure experiments and in vivo studies, we compared BC-IP and BPA, with a focus on boron uptake and retention characteristics. The results showed that although BC-IP had a lower boron uptake than BPA, it exhibited superior retention. Furthermore, despite lower boron accumulation in tumors, BC-IP showed significant survival improvement in glioma-bearing rats compared to controls. These results suggest that BC-IP, with its unique properties, may be an alternative boron carrier for BNCT. Further research is required to optimize this potential treatment modality, which could significantly contribute to advancing the treatment of high-grade gliomas.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Breakage and damage of fiber optic cable fibers seriously affect the normal operation of fiber optic networks and it is important to quickly and accurately determine the type and location of faults when they occur. The advantages of wavelet transform in singular signal detection and signal filtering are used to analyze Optical Time Domain Reflectometer (OTDR) curve signal and the fault detection method of fiber communication link with no relay and large span in high altitude area is given, which realizes the accurate detection and location of optical fiber communication link fault events under strong noise. The theoretical analysis is basically consistent with the experimental data. The accuracy of optical fiber fault location has been greatly improved in performance. The method has been directly applied to the field detection of ultra-long optical fiber links in high altitude areas, which has certain significance for the future real-time monitoring of optical fiber cables.

At Mae-Moh power plant, Thailand, superheater tubes, which are exposed in fly ash environ-ment, often degrade due to solid particle erosion. To extend the service lifetime of the superheater tubes, the high velocity oxy-fuel (HVOF) thermal spray technique is used to deposit a protective coating on the material, SA213-T22 steel. In this work, the solid particle erosion of the Co-28Cr and WC-12Co coatings was investigated using erodent particle impingement at the angles of 30o and 90o with an average particle size of 60 μm. The erosion behavior of SA213-T22 with and without Co-28Cr and WC-12Co coatings was explained using ductile and brittle erosion modes. The erosion test resulted in the brittle mode for both Co-28Cr and WC-12Co coatings, while SA213-T22 without coating indicated the ductile mode. On the investigation of surface morphology, the Co-28Cr coating showed mostly microcracks in contrast with the WC-12Co coating, fracture, de-bonding and deep cavities were also observed. Erosion resistance of the Co-28Cr coating was significantly higher than the WC-12Co coating, due to high hardness, low porosity and high density of the coating.

Limited availability of expensive alloying elements elevates low-alloyed steels to a unique position in the field of lightweight construction and mass production. Quenching and partitioning (Q&P) heat treatments of low-alloyed steels with exceptional property combinations are particularly promising. In this study, we characterize for the first time a new low-alloyed steel to be processed by Q&P heat treatments. In combined experimental and numerical studies, we design a novel approach that effectively combines the short cycle times of press hardening with the excellent property profiles of Q&P-treated steels. We identify appropriate transformation parameters for Q&P heat treatments by dilatometric studies and we adjust a number of reference conditions with different isothermal holding times. By means of SEM analysis and XRD measurements, we show that different fractions of retained austenite result in different mechanical properties. Initial numerical designs of the process can identify varying temperature profiles and cooling rates depending on the position in the die. The results show that the geometry of the part plays a minor role, but the die temperature is the dominant factor for successful partitioning directly in the press hardening process.

Hardaliye, a traditional non-alcoholic beverage, made from red grape pomace from wine production and produced by lactic acid fermentation with addition of different concentrations of whole/ground or heat-treated mustard seeds and of sour cherry leaves. Short shelf life of hardaliye limits its consumption and search in trend to process hardaliye to extend its shelf life. Thus, high hydrostatic pressure treatment of hardaliye drink with determination of changes in physicochemical and sensory properties in addition to microbial inactivation were studied according to Box-Behnken design. Maximum 5.10±0.00, 4.21±0.00, 5.38±0.59 and 5.05±0.22 log reductions were obtained in total mesophilic aerobic bacteria, total mold and yeast, Brettanomyces bruxellensis and Lactobacillus brevis by HHP. Shelf-life studies of the hardaliye samples were conducted with optimum processing parameters of 490 MPa, 29 oC for 15 min with the response variables of OD520 and inactivation of L. brevis. Both control and HHP treated samples were stored at 4 and 22 C for shelf-life studies. While control samples at 4 and 22 °C were spoiled at the 15th and 3rd days, HHP treated samples were spoiled after 108th and 228th days, respectively.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

Multi-level direct networks fueled by the evolving technology of active optical cables and increasing pin-bandwidth achieve reduced diameters and cost, with high-radix switches. These networks, like Dragonfly, are becoming the preferred aspirants for extreme high-performance parallel machines such as exa-scale computing. In this paper, we introduce a Hyper Z-Tree topology, which deploys the Z-Tree, a variant of fat-tree, as a computing node of a Generalized Hypercube (GHC) configuration. The resulting configuration provides higher bisection bandwidth, lower latency for some applications and higher throughput. Furthermore, the levels of the fat tree offer several path diversities across the GHC dimensions, hence conceding a more fault tolerant architecture. To profit from these path diversities, we propose two adaptive routing algorithms, which are extensions to the routing algorithm suggested in HyperX topology. These two algorithms exhibit better latencies and throughput than the HyperX.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

The petrogenesis of high Ba-Sr granitoids provide a great significance to penetrate the Proto-Tethys evolution in the North Qilian orogenic belt. This paper presents a combination of zircon U-Pb age, whole-rock major and trace element concentrations, and Sr-Nd-Hf isotopic data for Caowa high Ba-Sr dioritic intrusion from the eastern part of the North Qilian orogenic belt, aiming to decipher its petrogenesis and tectonic setting. LA-ICP-MS zircon U-Pb dating yields an emplacement age of 447±3 Ma for the Caowa intrusion, indicating a magmatic activity of the late Ordovician. The Caowa quartz diorites contain moderate contents of SiO2, MgO, Mg# and resultant high concentrations of Na2O+K2O, Fe2O3T and Al2O3, displaying calc-alkaline and metaluminous characteristics. Their relatively elevated Ba (up to 1165 ppm) and Sr (561 to 646 ppm) contents, with obvious enrichment in LILEs (e.g. Ba、Th、U) and depletion in HFSEs (e.g. Nb、Ta、Ti) resemble those of typical high Ba-Sr granitoids in subduction zone. Together with enriched Sr-Nd isotopic compositons[(87Sr/86Sr)i=0.7082−0.7086, εNd(t)= -5.1 to -4.9], and relatively extensive εHf(t) values (-13.2 to +8.5) of zircons, it suggests that these high Ba-Sr quartz diorites were derived from a mixture magma source between the ancient crust materials and the enriched lithospheric mantle metasomatised by fluid was released from subducted oceanic crust or sediment. Taking into account the ophiolites, high pressure metamorphic rocks and arc magmatic rocks in the region, we infer that affected by the northward subduction of the Qilian Proto-Tethys ocean, the Laohushan oceanic crust of the North Qilian back-arc basin was subducted during the Late Ordovician and resulted in extensive metasomatism of lithospheric mantle by fluids derived from oceanic crust or sediments, and the Caowa high Ba-Sr quartz diorites generated in the process of crust-mantle interaction during the Late Ordovician.

Lifestyle physical activity (PA) and nutrition are known to be effective interventions in preventing and managing obesity related comorbidities is adult populations, but less so in children and adolescents. We examined the effectiveness of lifestyle interventions in children from minority ethnic populations in western high-income countries. Our systematic review included 53 studies involving 26045 children from minority ethnic populations within western countries, who followed lifestyle intervention programs lasting between 8 weeks and 5 years with an aim to prevent and/or manage childhood obesity and associated comorbidities, including adiposity and cardiometabolic risks. Studies were heterogenous in terms of lifestyle intervention components (nutrition, PA, behavioural counselling) and settings (community vs. schools and after schools). Our meta-analysis included 31 eligible studies and showed no significant effects of lifestyle interventions when they focused on body weight and body mass index (BMI) outcomes [pooled BMI mean change = -0.09 (95% CI -0.19, 0.01), p=0.09]. This was irrespective of the intervention program duration (< 6 months vs. ≥ 6 months), type (PA vs nutrition/combined intervention) and weight status (overweight or obese vs no normal weight), all showed no significant effects in the sensitivity analysis. Nonetheless, 19 of the 53 studies reported reduction in BMI, BMI z scores and body fat percentage. However, majority of lifestyle interventions adopting a quasi-design with a combined primary and secondary obesity measures (11 out of 15 studies), were effective in reducing obesity comorbidities of cardiometabolic risks including metabolic syndrome, insulin sensitivity, and blood pressure in children with overweight and obesity. Preventing childhood obesity and associated comorbidities in children from high-risk ethnic minority groups is best achieved using a combined PA and nutrition intervention approach, which jointly target preventing obesity and cardiometabolic disease primary and secondary outcomes, especially measures of diabetes, hypertension, and cardiovascular disease.

INTRODUCTION There have been several advances in the treatment of hepatitis C virus (HCV) infection which have resulted in major reductions in the morbidity and mortality from liver-associated disease. These are not widely available in the Caribbean, due in part, to lack of knowledge of the epidemiology of infections with HCV. As efforts are made to eliminate HCV from the region, these and other existing barriers such as lack of an established database on HCV must be addressed. This review seeks to identify gaps in the knowledge of HCV in the Caribbean with respect to seroprevalence, genotype distribution and general epidemiologic characteristics. MATERIALS AND METHODS The literature for the period January 1, 2005, to October 2022, was reviewed to gather country specific data on HCV across the Caribbean. References were identified through indexed journals accessed through established databases. The usage pattern of HCV drugs was determined from data obtained from Pharmacists and Infectious Diseases Specialists across the region. RESULTS The prevalence of HCV in the Caribbean was 1.5%; the region should therefore be considered an area of moderate prevalence. Notably, data from specific countries were limited. The prevalence of HCV among intravenous drug users (21.9-58.8%); persons living with HIV/AIDS (0.8 to 58.5%); prisoners (32.8-64%) and men who have sex with men (MSM) (0.8-6.9%) was generally higher than in the general population (0.8-2.3%). Genotype 1 (83% was most prevalent followed by genotypes 2 (7.2%) and 3(2.1%), respectively. Drugs currently being used for treatment of HCV infections across the Caribbean include Epclusa (Sofosbuvir/velpatasvir), and Harvoni (Ledipasvir/sofosbuvir). Some of these drugs, are only available in the private sector and are sourced externally whenever needed. CONCLUSION There is a paucity of current data on the seroprevalence of HCV in the Caribbean and well-designed prospective studies are indicated to drive the implementation of treatment and control programs for HCV in the region. Barriers which need to be first overcome include unavailability and high cost of drugs used to treat HCV infections, injecting drug use and limited access to medical care and laboratory testing.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

Several studies have reported a relationship between autonomic dysfunction　 during tasks and Internet addiction. Changes within 24 h regarding heart rate variability (HRV) may be a more sensitive indicator than short term observations. We evaluated the influence of excessive Internet usage on HRV using a 24 h electrocardiogram (ECG) and examined acute changes during computer game tasks. A total 13 high school students and 22 young adults were recruited, and divided into excessive Internet user and non- excessive user groups based on Internet addiction test scores. The ECG was recorded continuously for 24 h by a wearable sensor and during two computer games (the Iowa gambling task and each participant’s preferred game) using a standard type ECG system. Multiple psychometric tests were also conducted. The excessive Internet user group exhibited clinically significant depressive symptoms, and higher self-reported scores for anxiety, impulsivity, autistic tendencies, and sleep problems than the non- excessive internet user group. There were weak differences within the 24 h high-frequency (HF) band power between two groups. During the Iowa gambling task, younger participants exhibited a reduced HF response, which may be related to weaker top- down self- regulatory mechanisms.

In engineering practice, various types of information data are affected by many factors during the collection process. For example, information data measurement errors are caused by equipment performance and the working environment. During the transmission of detection information, the signal distortion caused by energy loss and signal interference causes unpredictable detection errors in the collected information data. Through the study of fractional calculus theory, it was found that it is suitable for studying nonlinear, non-causal, and non-stationary signals, and has the dual functions of improving detection information and enhancing signal strength. Therefore, under the influence of many factors, we applied the fractional difference algorithm to the field of information data processing. Multi-sensor detection data fusion algorithm based on the fractional partial differential equation was adopted to establish its online detection data. A multi-sensor detection data fusion algorithm based on a fractional partial differential equation is established, which effectively fuses the information data detection errors caused by various influencing factors and greatly improves the detection accuracy of information data. The effectiveness of this method is proved through its application in an experiment.

Background: High blood pressure (BP) has been implicated as a major risk factor for cardiovascular diseases in several global populations, including in individuals of African ancestry. Despite the elevated burden of high BP-induced cardiovascular diseases in Africa and other global populations with African ancestry, limited genetic studies have been carried out to explore the genetic machinery driving this phenomenon. Methods: We performed univariate and multivariate analyses using Genome-wide association studies (GWAS) and summary statistics data of 77,850 individuals of African ancestry for systolic (SBP) and diastolic blood pressure (DBP) traits. The six independent cohorts used included individuals derived from the African Partnership for Chronic Disease Research (APCDR), the UK Biobank, and the Million Veteran Program (MVP). Subsequently, we annotated, prioritized, visualized, and interpreted our meta-analyses results using FUMA, to gain further insight into the molecular mechanism(s) that contribute to the genetics of BP traits. Finally, loci attaining genome-wide significance, GWS (p<5x10-8) were also followed up with Bayesian fine-mapping to identify potential causal variants. Results: Our meta-analyses altogether identified 350 GWAS SNPs for SBP (166 SNPs) and DBP (184 SNPs, including two novel loci) whilst our multivariate GWAS method identified 166 SNPs (including three novel loci). Interestingly, in FUMA there was significant tissue enrichment of up-regulated differentially expressed genes (DEGs) in the sigmoid and transverse colon for SBP, as well as 10 significant gene sets from MAGMA gene set analyses, However, for DBP, no significant DEGs nor gene sets in MAGMA were found; instead, in DBP for gene property analysis for tissue specificity nine candidates were found to be significant and all nine were in different brain regions. Finally, Bayesian fine-mapping revealed that only 11 variants from the lead SNPs had >50% posterior probability (PP) of being causal and they included novel variant rs562545 (MOBP, PP = 77%) and 10 other previously published variants. Conclusion: Our results demonstrate the importance of performing GWAS in large sample sizes of global populations of African ancestry, including continental Africans; which yield novel insights, from novel loci to novel pathways/tissue expression candidates. Large-scale genomic datasets are required to enhance further discovery and fine-mapping of high-risk loci/variants in highly susceptible groups for cardiovascular disease and other related traits. Our study highlights the need for diversity in genetic research and the importance of expanding large GWASs to include ancestrally diverse populations.

To create normative scores for all CrossFit® Open (CFO) workouts and compare male and female performances, official scores were collected from the official competition leaderboard for all competitors of the 2011-2022 CFO competitions. Percentiles were calculated in athletes (18 – 54 years) who completed all workouts within a single year ‘as prescribed’ and met minimum scoring thresholds. Independent t-tests revealed significant (p &lt; 0.05) sex differences for 56 of 60 workouts. In workouts scored by repetitions completed, men completed more repetitions in 18 workouts by small-to-large differences (d = 0.22-0.81), whereas women completed more repetitions in 6 workouts by small-to-medium differences (d = 0.36-0.77). When workouts were scored by time-to-completion, men were faster in 10 workouts by small-to-large differences (d = 0.23-1.12), while women were faster in three workouts by small differences (d = 0.46). In three workouts scored by load lifted, men lifted more weight by large differences (d = 2.00-2.98). All other differences were either trivial or not significant. Despite adjusted programming for men and women, the persistence of performances differences across all CFO workouts suggest resultant challenges are not the same. These normative values may be useful to training and research in male and female CrossFit® athletes.

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.

Canola is the major oilseed crop of Canada. The de-oiled material is an important by-product due to its rich phenolic profile and high protein content. This co-processing stream from canola is primarily utilized as animal feed but represents an invaluable source of nutraceuticals. Microwave-assisted solvent extraction (MAE), as a green extraction method, has received considerable attention in recent times. The ease of use and application of many solvents at the same time makes the MAE one of the best methods for studying multiple solvents at the same time. The formation of canolol, from sinapine and sinapic acid, is primarily dependant on temperature which favors the decarboxylation reaction. Hence, MAE using green extractants can be used to enhance the yield of canolol. This study examined the effects of different pre-treatment temperature-time combinations of 140, 150, 160, and 170℃ for 5, 10, 15, 20 and 30 minutes on the extraction of canolol and other canola endogenous phenolic compounds. Three antioxidant assays assessed the antioxidant activity of the different extracts obtained by MAE confirming the microwave as a novel and versatile instrument for enhancing the yield of canolol. Improvements in the antioxidant activity of the different extracts further established the efficacy of the current method for isolating important natural phenolic derivatives for utilization by the nutraceutical industry.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

The article is devoted to identifying promising research issues on the topic of Digital Industry based on the analysis of bibliometric data from Scopus platform for 2018–2022. The definition of promising issues derived from the titles, additionally abstracts, of highly cited works by authors with high publication activity. Authors' Scopus profiles were used to determine their affiliations, which are important for in-depth analysis of selected promising Digital Industry tasks. Metadata filtering to identify highly cited papers on particular issues was performed by keywords, Subject Areas, affiliations with countries and sponsoring organizations. Additionally, bibliometric metadata were clustered based on the co-occurrence of terms using VOSviewer. Within these clusters, articles of interest were identified for the formulation of promising research issues on the topic of Digital Industry, which will be subjected to in-depth analysis in separate papers.

By drilling periodic thru-holes in a suspended film, the phonon system can be modified. Being motivated by the BCS theory, the technique, so-called phonon engineering, was applied to a niobium sheet. The newly emergent high-T_c superconductivity, however, cannot be accounted for by the BCS theory. Rather, its exposed configuration, namely a square-lattice oxygen network, is reminiscent of the copper--oxygen plane in cuprate high-T_c superconductors. It turns out that its magnetic result is consistent with the principle of giant atom, which was developed by another heroes of superconductivity, Fritz London and John Slater, in the 1930s, several decades earlier than the propagation of BCS theory. The superconducting transition feature is discussed on the basis of a comprehensive theory of the giant atom---the theory of hole superconductivity.

The stress imposed by ethanol to Saccharomyces cerevisiae cells are one of the most challenging limiting factors in industrial fuel-ethanol production. Consequently, the toxicity and tolerance to high ethanol concentrations has been the subject of extensive research, allowing the identification of several genes important for increasing the tolerance to this stress factor. However, most studies were performed with well characterized laboratory strains, and how the results obtained with these strains work in industrial strains remains unknown. In the present work we have tested three different strategies known to increase ethanol tolerance by laboratory strains in an industrial fuel-ethanol producing strain: overexpression of the TRP1 or MSN2 genes, or overexpression of a truncated version of the MSN2 gene. Our results show that the industrial CAT-1 strain tolerates up to 14% ethanol, and indeed the three strategies increased its tolerance to ethanol. When these strains were subjected to fermentations with high sugar content and cell-recycle, simulating the industrial conditions used in Brazilian distilleries, only the strain with overexpression of the truncated MSN2 gene showed improved fermentation performance, allowing the production of 16% ethanol from 33% of total reducing sugars present in sugarcane molasses. Our results highlight the importance of testing genetic modifications in industrial yeast strains under industrial conditions in order to improve the production of industrial fuel ethanol by S. cerevisiae.

The article is devoted to solving the problem of searching for universal explainable features that can remain explainable for a wide class of objects and phenomena and become an integral part of Explainable AI (XAI). The study is implemented on the example of an applied problem of early diagnostics of plant stress, using Thermal IR (TIR) and HSI, presented by 8 vegetation indices/channels. Each such index was presented by 5 statistical values. A Single-Layer-Perceptron classifier was used as the main instrument. TIR turned out to be the best of the indices in terms of efficiency in the field and sufficient to detect all 7 key days with 100% accuracy. Our study shows also that there are a number of indices, inluding NDVI, and usual color channels Red, Green, Blue, which are close to TIR possibilities in early plant stress detection with 100% accurasy or near, and can be used for wide class of plants and in different conditions their treatment. The stability of the stress classification in our study was maintained when the training set was reduced up to 10% of the dataset volume. The entropy-like feature of (max-min) for any indices/channels have determined as a leadersheep universal high-level explainable feature for the plant stress detection, which used in interaction with some of other statistical features.

The purposes of this study are to analyze the groundwater quality of Ogallala Aquifer and evaluate the hydrological characteristics in the southern High Plains region of the Permian Basin, Texas. Levels of chloride, fluoride, nitrate, pH, selenium, and total dissolved solids (TDS) were analyzed through the years 1990-2016. A total of 133 wells were collected from the Texas Water Development Board (TWDB) which is an open database by the US government. Statistical analysis was utilized to evaluate the groundwater quality and propose trends. The average levels of the contaminants were compared to their respective Maximum Contaminant Levels (MCL) by the Environmental Protection Agency (EPA). Potential human health risks that each contaminant possesses were described. Possible sources of each contaminant were discussed with oil/gas activities, agricultural practices, and other human actions impact its conditions. This research provides important information for groundwater quality of Ogallala aquifer and contributes on understanding the response to development in the Permian Basin, Texas.

This study was carried out to determine the effects of apple vinegar and sodium diacetate addition on the aerobic stability of fermented high moisture maize grain (HMM) silage after opening. In the study, the effect of three different levels (0, 0.5, 1.0%) of apple vinegar (AV) and sodium diacetate (SDA) supplementation to fermented HMM at two different storage conditions (27-29°C, 48% Humidity; 35-37°C, 26% Humidity) were investigated. The material of the study was fermented rolled maize grain with 62% moisture content stored for about 120 days. Silage samples were subjected to aerobic stability test with 3 replicates for each treatment group. Wendee and microbiological analyses were made at 0, 2, 4, 7, and 12 days. Meanwhile, samples were displayed in the T200 IR brand thermal camera. According to the thermogram results, 1% SDA addition positively affected HMM silages at the second and fourth days of aerobic stability at both storage conditions (p<0.05). Aerobic stability and infrared thermography analysis indicated that 1% AV, 0.5%, and 1% SDA additions to HMM silages had promising effects. Due to our results, we concluded that thermal camera images might be used as an alternative quality indicator for silages in laboratory conditions.

Immunoglobulin G (IgG) adopts a modular multidomain structure that mediates antigen recognition and effector functions, such as complement-dependent cytotoxicity. IgG molecules are self-assembled into a hexameric ring on antigen-containing membranes, recruiting the complement component, C1q. To provide deeper insights into the initial step of the complement pathway, we report a high-speed atomic force microscopy study for quantitative visualization of the interaction between IgG and the C1 complex composed of C1q, C1r, and C1s. Results showed that C1q in the C1 complex is restricted regarding internal motion and has a stronger binding affinity for on-membrane IgG assemblages than C1q alone, presumably because of smaller conformational entropy loss upon binding. Furthermore, we visualized a 1:1 stoichiometric interaction between C1/C1q and an IgG variant that lacks the entire CH1 domain in the absence of antigen. In addition to the canonical C1q-binding site on Fc, their interactions are mediated through a secondary site on the CL domain that is cryptic in the presence of the CH1 domain. Our findings offer clues for novel-modality therapeutic antibodies.

We describe a method for protein quantification and for mRNA quantification in small sample quantities of human induced pluripotent stem-cell-derived-cardiomyocytes (hiPSC-CMs). Demonstrated here is how the capillary-based protein detection system Wes^TM by ProteinSimple and the Power SYBR^TM Green Cells-to-CT^TM Kit by Invitrogen can be applied to individual samples in a 96-well microplate format and thus made compatible with high-throughput (HT) cardiomyocyte assays. As an example of the usage, we illustrate that Cx43 protein and GJA1 mRNA levels in hiPSC-CMs are enhanced when the optogenetic actuator, channelrodopsin-2 (ChR2), is genetically expressed in them. Instructions are presented for cell culture and lysate preparations from hiPSC-CMs, along with optimized parameter settings and experimental protocol steps. Strategies to optimize primary antibody concentrations as well as ways for signal normalization are discussed, i.e. antibody multiplexing and total protein assay. The sensitivity of both the Wes and Cells-to-CT kit enables protein and mRNA quantification in a HT format, which is important when dealing with precious small samples. In addition to being able to handle small cardiomyocyte samples, these streamlined and semi-automated processes enable quick mechanistic analysis.

Insulin receptors are internalized by endothelial cells; however, the impact of hyperinsulinemia on this process is not known. Thus, the aim of this study is to determine the role of hyperinsulinemia on insulin receptor function and internalization, as well as the potential impact of protein tyrosine phosphatase 1B (PTP1B). To this end, hippocampal microvessels were isolated from male C57Bl/6J mice on either a control or high-fat diet and assessed for insulin receptor signaling. Cell surface insulin receptors in brain microvascular endothelial cells were labelled with biotin to assess the role hyperinsulinemia plays on receptor internalization in response to stimulation, with and without Claramine treatment, a potent PTP1B antagonist. Our results indicated that insulin receptor levels increased in tandem with insulin receptor dysfunction in the high-fat diet mouse hippocampal microvessels. Hyperinsulinemic cell-receptors demonstrate a shift in splice variation towards decreased IR-A/IR-B ratios and demonstrate a higher membrane-localized proportion. This corresponded with decreased autophosphorylation at sites critical for receptor internalization and signaling, however, Claramine restored signaling and receptor internalization in hyperinsulinemic cells. In conclusion, hyperinsulinemia negatively impacts brain microvascular endothelial cell insulin receptor function and internalization, likely through both alternative splicing and increased negative feedback from PTP1B.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

Rapid isolation of white blood cells (WBCs) from whole blood is an essential part of any WBC examination platform. However, most conventional cell separation techniques are labor-intensive and low throughput, require large volumes of samples, need extensive cell manipulation, and have low purity. To address these challenges, we report the design and fabrication of a passive, label-free microfluidic device with a unique U-shaped cross-section to separate WBCs from whole blood using hydrodynamic forces that exist in a microchannel with curvilinear geometry. It is shown that the spiral microchannel with a U-shaped cross-section concentrates larger blood cells (e.g., WBCs) in the inner cross-section of the microchannel by moving smaller blood cells (e.g., red blood cells (RBCs) and platelets) to the outer microchannel section and preventing them from returning to the inner microchannel section. Therefore, it overcomes the major limitation of a rectangular cross-section where secondary Dean vortices constantly enforce particles throughout the entire cross-section and decrease its isolation efficiency. Under optimal settings, more than 95% of WBCs can be isolated from whole blood under high-throughput (6 ml/min), high-purity (88%), and high-capacity (180 ml of sample in 1 hour) conditions. High efficiency, fast processing time, and non-invasive WBC isolation from large blood samples without centrifugation, RBC lysis, cell biomarkers, and chemical pre-treatments make this method an ideal choice for downstream cell study platforms.

Farmers and seed companies constantly require high-quality seeds with excellent agronomic performance. However, faced with environmental adversity, limited natural resources and increasing food demand around the globe, more attention has turned to improving crop plant production by implementing efficient strategies. Seed priming technology has shown promising biological improvements leading to suitable agronomic performance in crop plants under adverse environmental conditions. Seeds are subjected to controlled conditions that are conducive to complex physiological, biochemical, and molecular changes, conferring specific stress tolerance to subsequent germination and growth conditions. In this review paper, we aimed to study the recent approaches in the efficiency of hydropriming, osmopriming, chemopriming, hormopriming, nanopriming, matrix priming, biopriming, physical priming and hybrid priming procedures in the production of crop plants under environmental adversity, as well as their biological mechanism changes. All priming methods demonstrated relevant changes in the biological mechanism related to crop plant production by mitigating salinity effects, heavy metals, and flooding stress and enhancing chilling, heat, drought and phytopathogen tolerance. We strongly recommend that researchers combine multiple priming methods, known as hybrid priming, in their investigations to provide novel technologies and additional biological approaches to enhance the knowledge of crop plant science. Thus, the findings shed light on the use of seed priming technology as a key strategy to increase crop plant production under environmental adversity by acquiring stress tolerance and enhancing agronomic traits to meet the global food demand.

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

It has been known that the performance of the High-Pressure Grinding Rolls (HPGR) varies as a function of method used to confine laterally the rolls, their diameter/length (aspect) ratio as well as their condition, if new or worn. However, quantifying these effects through direct experimentation in machines with reasonably large dimensions is not straightforward given the challenge, among others, of guaranteeing that the feed material remains unchanged. The present work couples the discrete element method (DEM) to multibody dynamics (MBD) and a novel particle replacement model (PRM) to simulate the performance of pilot-scale HPGRs grinding pellet feed. It shows that rotating side plates, in particular when fitted with studs, allow reaching more uniform forces along the bed, which also translates in a more constant product size along the rolls as well as higher throughput. It also shows that the edge effect is relatively constant with roll length, leading to substantially larger proportional edge regions for high-aspect ratio rolls. On the other hand, the product from the center region of such rolls was found to be finer when pressed at identical specific forces. Finally, rolls were found to have higher throughput, but generate a coarser product when worn following the commonly observed trapezoidal profile. The approach used in industry to compensate for roller wear by increasing the specific force and roll speed has then been demonstrated to be effective to maintain and potentially even increase product fineness and throughput, as long as the minimum safety gap is not reached.

Based on panel data of 31 provincial-level administrative units (excluding Hong Kong, Macao and Taiwan) in China from 2015 to 2019, using fixed effect model and mediation effect model, this paper makes an empirical analysis on the interaction among digital economy, industrial structure upgrade and high-quality economic development. The results show that, from the overall effect, the digital economy can significantly promote the high-quality development of the economy, and there are regular regional differences, and the relationship between the promotion intensity and the development level of the digital economy is proportional. From the mediation effect, in the relationship between digital economy and high-quality economic development, the upgrade of industrial structure has played a significant part of the mediation effect, the proportion of mediation effect is 25.17% . In addition, the mediation effect of industrial structure upgrade has obvious regional difference, the western area is the strongest, the eastern area is the second, the central area is the weakest. Based on the above research,the concrete policy suggestions are given to promote the development of digital economy and upgrade the level of industrial structure to promote the high-quality development of economy.

Sugar-sweetened beverages are associated with metabolic dysfunction, particularly in those with increased risk factors. Artificial sweeteners (AS) are often promoted as a healthier alternative, yet findings remain conflicting as to their effects on metabolic function. Further, there is a lack of data exploring the interaction between AS and high-fat diets (HFD). We therefore examined the effects of HFD and the AS Acesulfame-potassium (Ace-K) on glucose intolerance and adipose tissue physiology in male and female C57BL/6 mice. 40 mice were randomised to receive either a) a control diet (CDCon; standard control diet/water), b) control diet and Ace-k (CDAS; CD/7.5mM AS in drinking water), c) HFD (HFCon; HFD (45%kcal from fat)/water), or d) HF and AS (HFAS; HFD/7.5mM AS in drinking water) for 6 weeks. A HFD increased body weight in male and female mice independently of AS supplementation. AS induced sex-specific effects protecting against HFD-induced hyperglycaemia and adipocyte hypertrophy in male mice and reducing inflammatory gene expression in the adipose tissue. Conversely in females, AS induced hyperinsulinemia in HFD mice and increased expression of immune-related genes. These findings suggest that supplementation of HFD with AS exacerbates metabolic dysfunction in female mice. This work supports the importance of studying sexually dimorphic responses to an altered nutritional environment and highlights the need for further investigation into the intake of AS, particularly in those already at risk of metabolic disease such as the obese or overweight.

This paper proposes a multifractal model, with the aim of providing a possible explanation for the locality phenomenon that appears in the estimation of the Hurst exponent in stationary second order temporal series representing self-similar traffic flows in current high-speed computer networks. It is shown analytically that this phenomenon occurs if the network flow consists of several components with different Hurst exponents.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

Tarsal tunnel syndrome is a focal compressive neuropathy of the posterior tibial nerve or one of its associated branches. Brief mention is made in the literature of the use of corticosteroid injections for this condition. The basic technique of hydrodissection is used for other nerve entrapments and includes identifying the region of nerve compression, and the injection of a fluid medium to dissect between structures or fascial planes. We introduce our treatment protocol using a methylprednisolone/sterile water/ropivacaine hydrochloride injectate mix and peripheral nerve stimulation to a perform hydrodissection technique for tarsal tunnel syndrome.

Background and objectives: Induction of labor (IOL) is an event that occurs in up to one-quarter of pregnancies; less is known about the outcomes and safety of IOL in obese pregnant woman; no data is available on misoprostol vaginal insert (MVI) IOL in high-risk pregnancy obese women. Objectives: (1) to evaluate the rate of successful IOL with 200 μg MVI in obese (Body Mass Index - BMI over 30 kg/m2) high-risk pregnant women: late-term pregnancy, hypertension or diabetes, compared to obese non-high-risk ones; (2) to evaluate the safety profile of MVI in high-risk pregnancy obese patients. Study design: We conducted a cross-sectional study in "Filantropia" Clinical Hospital, Bucharest, Romania, from June 2017 to September 2019 (28 months). From a total of 11,096 registered live births, IOL was performed in 206 obese patients; 74 obese high-risk pregnant patients matched the inclusion criteria; of these, 33.8% pregnancies (n=25) were late-term (41 – 41+6 weeks), 43.2% (n=32) had associated pathologies (hypertension and diabetes); labor induction was guided using a standardized protocol. We evaluated the maternal and gestational age, parity, fetal tachysystole, hyper-stimulation, initial cervical status, time from induction to delivery, drug side effects, mode of delivery, and neonatal outcomes. Results: (a) The overall successful labor induction rate, evaluated by the vaginal delivery rate, was 71.6% (n=53), spontaneously or instrumentally assisted; 28.4% (n=21) births were unsuccessful MVI IOL, converted into caesareans. (b) No significant differences were found regarding the maternal outcomes; in terms of perinatal outcomes of safety, four cases of high-risk pregnancies vaginally delivered were associated with neonatal intensive care unit (NICU) admissions and a one-minute Apgar score under seven (5.4%). Most cases with adverse effects of misoprostol have been managed conservatively, except for three emergency C-section cases. Conclusions: Misoprostol vaginal insert is a safe choice in IOL in obese high-risk pregnancies with good maternal and perinatal outcomes.

To improve the voltage gain of step-up converters, cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the converter takes the advantages of both impedance source and cascaded converters. However, by applying some modifications, the proposed converter provides high voltage gain while the voltage stress of switch and diodes are still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in order to expand the lifetime of PV panels. After analyzing the operation principles of the proposed converter, simulation and experimental results of a 100W prototype are presented to verify the proposed converter performance.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Suboptimal health status (SHS) is a state between health and disease, has several associated factors, although, its underlying mechanism is still unclear. This study aimed to investigate the status of SHS and its associated factors of high school students in three areas of China (Shanxi, Guangzhou, and Tibet). A multidimensional sub-health questionnaire of adolescent (MSQA) is used to evaluate SHS. Among 1461 respondents, females proportion 56.47% was higher than males 43.53% where SHS was higher in Shanxi followed by Tibet and then Guangzhou. The rural area, grade, lack of sleep, home visit in a week, lack of exercise, a heavy burden of study, smoking, drinking, and fewer friends were the risk factors of SHS, while, families living status, seeking help and extroversion were the protective factors. SHS is significantly associated with different influencing factors. For comprehensive prevention and control measures, reduce the risk factors and enhance the protective factors.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Exploring the biological significance of mutations in SARS-CoV-2 coronavirus, causing the COVID–19 pandemic, has recently become an area of paramount interest for many researchers, who are pouring their tremendous efforts, in cracking the COVID–19 pandemic code. One of many such mutations that have occurred in the viral genome is V483A mutation, which is a part of the receptor-binding motif (RBM), present in the S1 domain of the spike protein. V483A mutant virus is becoming popular in North America with 36 cases so far, due to its frequent occurrences in recent days. In this review, we have assembled all information, currently available on V483A mutation, and have made a critical analysis based on the perspectives of many researchers all around the world. Comparison is made between the wild type and the V483A mutants to analyze certain factors like the type of interaction between the virus and host cell interface, binding affinity, stability, partition energy, hydrophobicity, occurrence rate, and transmissibility. Insilico dynamic analysis shows minimal alteration in the receptor-binding domain (RBD) of V483A mutant protein in free-state and no significant change of mutant tertiary structure of RBM upon binding to the ACE2 receptor. Comprehensive details about infectivity and evasion of the immune system by the virus are discussed. This information can in turn be of monumental importance in the field of vaccine and drug development because the mutants are becoming resistant to the vaccines and monoclonal antibodies.

For our research on droplet deformation and breakup in scaled high-pressure homogenizing units we developed a pressure stable inline droplet generator. It consists of an optically accessible flow channel with a combination of stainless steel and glass capillaries and a 3D printed orifice. The droplet size is determined online by live image analysis. The influence of the orifice diameter, the mass flow of the continuous phase and the mass flow of the disperse phase on the droplet diameter was investigated. Furthermore, the droplet detachment mechanisms were identified. Droplet diameters with small diameter fluctuation between 175 µm and 500 µm could be realized, which allows a precise adjustment of the Ca and We Number in the subsequent scaled high pressure homogenizer disruption unit. The determined influence of geometry and process parameters on the resulting droplet size and droplet detachment mechanism agreed well with literature on microfluidics. Furthermore, droplet trajectories in an exemplary scaled high-pressure homogenizer disruption unit are presented which show that the droplets can be reinjected on a trajectory close to the center axis or close to the wall, which should result in different stresses on the droplets.

Green Stormwater Infrastructure (GSI), a sustainable engineering design approach for managing urban stormwater runoff, has long been recommended as an alternative to conventional conveyance-based stormwater management strategies to mitigate the adverse impact of sprawling urbanization. Hydrological and hydraulic simulations of small-scale GSI measures in densely urbanized micro watersheds require high-resolution spatial databases of urban land use, stormwater structures, and topography. This study presents a highly resolved Storm Water Management Model developed under considerable spatial data constraints. It evaluates the cumulative effect of the implementation of dispersed, retrofitted, small-scale GSI measures in a heavily urbanized micro watershed of Costa Rica. Our methodology includes a high-resolution digital elevation model based on Google Earth information, whose accuracy was sufficient to determine flow patterns and slopes, as well as to approximate the subsurface stormwater structures. The model produced satisfactory results in event-based calibration and validation, which ensured the reliability of the data collection procedure. Simulating the implementation of GSI shows that dispersed, retrofitted, small-scale measures could significantly reduce impermeable surface runoff (peak runoff reduction up to 40%) during frequent, less intense storm events and delay peak surface runoff 5-10 minutes. The presented approach can benefit stormwater practitioners and modelers conducting small scale hydrological simulation under spatial data constraint.

Bacteria and archaea participate in and are influenced by processes of substance circulation and energy exchanges in natural environment. Generally, the community changes of bacteria and archaea in sediment are mainly driven by seasonality in mid-latitude regions. But in our study, water diversion to Fen river played a more important role on OTU number, diversity and community structure of bacteria and archaea in sediment than seasonal variation, which was found by 16S rRNA high-throughput sequencing technology. This phenomenon might be caused by external transferred water on the physicochemical water environment and accelerated release of positive nitrogen from sediment caused by rise of water level. Changes of carbon-nitrogen cycle and increase of electrical conductivity (EC) value induced more diversion-responders than season-responders both for bacteria and archaea. Seasonal changes have been influencing bacteria and archaea mildly throughout the whole study reach. After water diversion, the environment indicators relating to bacteria community obviously changed from nutrients to salinity while that for archaea almost disappeared. Our research showed the effects of human activities on the communities of bacteria and archaea outweigh the forcing from natural seasonal changes in mid-latitude regions and revealed the mechanism, highlighting different responses of bacteria and archaea to environmental changes.

This study presents a novel technique utilizing high frequency vibration to shorten treatment time and preserve alveolar bone in challenging orthodontic cases treated with Invisalign® clear aligners. Four non-growing orthodontic patients (age range 14-47 years old) with Class II skeletal patterns (convex profiles with retrognathic mandibles) who sought correction of their crowded teeth and non-surgical correction of their convex profiles were included in this study. These patients were treated using Invisalign clear aligners together with high frequency vibration (HFV) devices (120 Hz) (VPro5™) that were used by all patients for five minutes per day during active orthodontic treatment. Vertical control and forward rotation of the mandible for each patient was achieved through pre-programming the Invisalign to produce posterior teeth intrusion. Successful forward rotation of the mandibles achieved in all patients led to improvement of their facial convex profiles (ANB improved 2.1 + 0.5 degrees; FMA improved 1.2 +1.1 degrees). Dental decompensation was achieved by lingual tipping of the lower incisors and palatal root torque of upper incisors. The use of HFV together with Invisalign facilitated achieving these results within a 12+6 month period. In addition, more bone labial to the lower incisors after their lingual movement was noted. In conclusion, the use of HFV concurrent with SmartTrack Invisalign aligners allowed complex tooth movement and forward projection without surgery in non-growing patients with skeletal Class II relationships. The clinical impact and implications of this case series is that the use of HFV facilitates complex orthodontic tooth movement including posterior teeth intrusion and incisor decompensation in addition to increased bone formation labial to lower incisors that may minimize future gum recession due to their labial inclination.

Although it is known that the gut microbiota (GM) can be modulated by diet, the efficacy of specific dietary interventions in determining its composition and diversity in obese patients remains to be ascertained. The present work aims to evaluate the impact of a moderately hypocaloric Mediterranean diet on the GM of obese and overweight patients (OB). The GM of 23 OB patients (F/M= 20/3) was compared before (T0) and after 3 months (T3) of the nutritional intervention (NI). Fecal samples were analyzed by Illumina MiSeq sequencing of the 16S rRNA gene. At baseline, the GM characterization confirmed the typical obesity-associated dysbiosis. After 3 months of NI, patients presented a statistically significant reduction of the body weight and fat mass, along with changes in the relative abundance of many microbial patterns. In fact, we observed an increased abundance in several Bacteroidetes taxa (i.e. Sphingobacteriaceae, Sphingobacterium, Bacteroides spp., Prevotella stercorea) and depletion of many Firmicutes taxa (i.e. Lachnospiraceae members, Ruminococcaceae and Ruminococcus, Veillonellaceae, Catenibacterium, Megamonas). In addition, the phylum Proteobacteria showed an increased abundance, while the genus Sutterella, within the same phylum, decreased after the intervention. Metabolic pathways, predicted by bioinformatic analyses, showed a decrease in membrane transport and cell motility after NI. The present study extends our knowledge of the GM profiles in OB, highlighting the potential benefit of a moderate caloric restriction in counteracting the gut dysbiosis.

Archaeological topography identification from high-resolution DEMs is a current method that is used with high success in archaeological prospecting of wide areas. I present a methodology trough which burial mounds (tumuli) from LiDAR DEMS can be identified. This methodology uses geomorphometric and statistical methods to identify with high accuracy burial mound candidates. Peaks, defined as local elevation maxima are found as a first step. In the second step, local convexity watershed segments and their seeds are compared with positions of local peaks and the peaks that correspond or have in vicinity local convexity segments seeds are selected. The local convexity segments that correspond to these selected peaks are further feed to a Random Forest algorithm together with shape descriptors and descriptive statistics of geomorphometric variables in order to build a model for the classification. Multiple approaches to tune and selected the proper training dataset, settings and variables were tested. The validation of the model was performed on the full dataset where the training was performed and on an external dataset in order to test the usability of the method for other areas in a similar geomorphological and archaeological setting. The validation was performed against manually mapped and field checked burial mounds from two neighbor study areas of 100 km² each. The results show that by training the Random Forest on a dataset composed of between 75% to 100% of the segments corresponding to burial mounds and ten times more non-burial mounds segments selected using latin hypercube sampling, 93% of the burial mound segments from the external dataset are identified. There are 42 false positive cases that need to be checked, and there are two burial mound segments missed. The method shows great promise to be used for burial mound detection on wider areas by delineating a certain number of tumuli mounds for model training.

High-frequency near-infrared diode laser provides high peak output, low heat accumulation, and efficient biostimulation. Although these characteristics are considered suitable for osteoarthritis (OA) treatment, the effect of high-frequency near-infrared diode laser in in vitro or in vivo OA models has not yet been reported. Therefore, we aimed to assess the biological effects of high-frequency near-infrared diode laser irradiation on IL-1β-induced chondrocyte inflammation in an in vitro OA model. Normal Human Articular Chondrocyte-Knee (NHAC-Kn) cells were stimulated with human recombinant IL-1β and irradiated with high-frequency near-infrared diode laser (910 nm, 4 or 8 J/cm2). The mRNA and protein expression of relevant inflammation- and cartilage destruction-related proteins was analyzed. IL-1β treatment significantly increased the mRNA levels of IL-1β, IL-6, TNF-α, MMP-1, MMP-3, and MMP-13. High-frequency near-infrared diode laser irradiation significantly reduced the IL-1β-induced expression of IL-1β, IL-6, TNF-α, MMP-1, and MMP-3. Similarly, high-frequency near-infrared diode laser irradiation decreased the IL-1β-induced increase in protein expression and secreted levels of MMP-1 and MMP-3. These results highlight the therapeutic potential of high-frequency near-infrared diode laser in OA.

The cardioprotective effects of volatile anesthetics versus total intravenous anesthesia (TIVA) are controversial, especially in patients undergoing non-cardiac surgery. Using current generation high-sensitivity cardiac troponin (hs-cTn), we aimed to evaluate the effect of anesthetics on the occurrence of myocardial injury after non-cardiac surgery (MINS). From February 2010 to December 2016, 3555 patients without preoperative hs-cTn elevation underwent non-cardiac surgery under general anesthesia. Patients were grouped according to anesthetic agent; 659 patients were classified into a propofol-remifentanil total intravenous anesthesia (TIVA) group, and 2896 patients were classified into into a volatile group. To balance the use of remifentanil between groups, a balanced group (n=1622) was generated with patients who received remifentanil infusion in the volatile group, and two separate comparisons were performed (TIVA vs. volatile and TIVA vs. balanced). The primary outcome was occurrence of MINS, defined as rise of hs-cTn I ≥ 0.04 ng/mL within postoperative 48 hours. The secondary outcomes were 30-day mortality, postoperative acute kidney injury (AKI), and adverse events during hospital stay (mortality, type I myocardial infarction (MI), and new-onset arrhythmia). In propensity-matched analyses, the occurrence of MINS was lower in the TIVA group compared to the volatile group (OR 0.642; 95% CI 0.450-0.914; p = 0.014). However, after balancing the use of remifentanil, there was no difference between groups in the risk of MINS (OR 0.832; 95% CI 0.554-1.251; p-value = 0.377). There were no significant associations between the two groups in type 1 MI, new-onset atrial fibrillation, in-hospital and 30-day mortality before and after balancing the use of remifentanil. However, the incidence of postoperative AKI was lower in the TIVA group (OR 0.362; 95% CI 0.194-0.675; p-value = 0.001). After balancing the use of remifentanil, volatile anesthesia and TIVA showed comparable effects on MINS in patients undergoing non-cardiac surgery without preoperative myocardial injury. Further studies are needed on the benefit of remifentanil infusion.

Detection of the region of interest (ROI) is a critical step in laryngeal image analysis for the delineation of glottis contour. The process can improve both computational efficiency and accuracy of the image segmentation task, which will facilitate subsequent analysis and characterization of the vocal fold vibration as it correlates with voice quality and pathology. This study aims to develop machine learning based approaches for automatic detection of ROI for glottis image sequences captured by high-speed video-endoscopy (HSV), a clinical laryngeal imaging modality. In particular, we first applied the supporting vector machine (SVM) method using histogram of oriented gradients (HOG) feature descriptor, and second, trained a convolutional neural network (CNN) model for this task. Comparisons are made for both approaches in terms of accuracy of recognition and computation time.

By means of density functional theory (DFT) calculations, we have investigated the effect of hydrostatic pressure on the structural, electronic and elastic properties of the barium-doped silicon clathrate Ba8Si46 in the type-VIII structure (α phase). Physical properties are calculated under different conditions of pressure (0 GPa to 45 GPa) using the GGA-PBE functional, those calculations have been performed using the Cambridge serial total energy package CASTEP code within the Materials Studio package. Electronic properties have shown that the type-VIII Ba8Si46 has metal-like properties with a fundamental bandgap of 1 eV. Under pressure the fundamental bandgap increases slightly and the positions of the valence band maximum VBM and the conduction band minimum CBM remain unchanged. We found that the compound is mechanically stable under the pressure range, but this needs to be confirmed experimentally through synthesis, a comparison with the type-I and the guest-free counterparts has exhibited promising features for the type-VIII Ba8Si46.

Tissue engineering is an emerging field of research due to its growing impact on the regeneration of tissue injured from damage and organ failure. Small hydrogel microspheres containing regenerative cells and stimulators can be used as building blocks to regenerate tissue by injecting them into damaged areas; a microneedle is used to minimize the incision and any associated infections. To address the need for production of a large number of microspheres for use in tissue engineering, we developed a 3D coaxial multi-nozzle flow-focusing device fabricated via a simple 3D-printing method that demonstrates a high rate of microsphere production per nozzle. This device has six coaxial microscale nozzles that produce hydrogel microspheres. Two individual parts—the inlet and nozzle—can be made separately by a 3D printer and bonded together using uncured photo-curable resin as glue. The dimensions of the microspheres are between 100 μm and 1200 μm. They are produced by adjusting the flow rate ratio between the dispersed and continuous media. A flow rate ratio of 180 demonstrated the highest microsphere production rate of 2.12e+5 microspheres per sec (0.25 mL/min). This microsphere production rate per nozzle is four times higher than that of currently available devices.

The use of machine learning techniques in predictive health care is on the rise with minimal data used for training machine-learning models to derive high accuracy predictions. In this paper, we propose such a system, which utilizes Heart Rate Variability (HRV) as features for training machine learning models. This paper further benchmarks the usefulness of HRV as features calculated from basic heart-rate data using a window shifting method. The benchmarking has been conducted using different machine-learning classifiers such as artificial neural network, decision tree, k-nearest neighbour and naive bays classifier. Empirical results using MIT-BIH Arrhythmia database shows that the proposed system can be used for highly efficient predictability of abnormality in heartbeat data series.

Rice production, owing to its high-water requirement for cultivation, is very vulnerable to the threat of changing climate, particularly prolonged drought and high temperature. Such threats heighten the need for abiotic stress-resilient rice varieties with better yield potential. This review examines the physiological and molecular mechanisms of rice varieties to cope with stress conditions of drought (DS), high temperature (HTS) and their combination (DS-HTS). It appraises research studies in rice about its various phenotypic traits, genetic loci and response mechanisms to stress conditions to help craft new breeding strategies for rice varieties with improved resilience to abiotic stresses. This review consolidates available information on promising rice cultivars with desirable traits as well as advocates synergistic and complementary approaches in molecular and systems biology to develop new rice breeds that favorably respond to climate-induced abiotic stresses. The development of new breeding and cultivation strategies for climate-resilient rice varieties is a challenging task. It requires a comprehensive understanding of the various morphological, biochemical, physiological, and molecular components governing yield under drought and high temperature, but possible by implementing cohesive approaches involving molecular and systems biology approaches in genomics and molecular breeding, including genetic engineering.

Increasing of the imaging rate of conventional atomic force microscopy (AFM) is almost impossible without impairing of the imaging quality, since the probe tip tends to lose contact with the sample. We propose to apply the additional nonlinear force on the upper surface of a cantilever, which will help to keep the tip and surface in contact. In practice this force can be produced by the precisely regulated airflow. Such an improvement affects the AFM system dynamics, which were evaluated using a mathematical model presented in this paper. The model defines the relationships between the additional nonlinear force, the pressure of the applied air stream and the initial air gap between the upper surface of the cantilever and the end of the air duct. It was found that the nonlinear force created by the stream of compressed air (aerodynamic force) prevents the contact loss caused by the high scanning speed or higher surface roughness, and at the same time has minimal influence on the interaction force, thus maintaining stable contact between the probe and the surface. This improvement allows to effectively increase the scanning speed by at least 10 times using a soft (spring constant of 0.2 N/m) cantilever by applying the air pressure of 40 Pa. If a stiff cantilever (spring constant of 40 N/m) is used, the potential of accuracy improvement reaches 92 times. This method is suitable for use with different types of AFM sensors and can be implemented practically without essential changes in AFM sensor design.

This paper presents an experimental scenario aimed at bridging the gap between the cities we have and the cities we need, not only in the 21^st century but also beyond, using the integrated tools of development control and holistic land development model to achieve a planner-led vision of city sustainability. Due to scathing criticisms against the development control system, the paper contends that planners as development approving officers and public interest specialists are better positioned than allied professionals to increase city sustainability through a holistic development process that benefits from the concept of strong sustainability posited by ecological economists. The paper adopts a seven-stage, 56-cell land development matrix (model) to simulate the development of the typical high-rise residential condominium in Ontario, supported with secondary data and the author’s ground experience as a planner and realtor with condominium customer service experience across Toronto and Mississauga cities between 2008 and 2017. Findings reveal that planners can seize the opportunity of being leaders of the development team to synergize the risks and value creation in land development that are key drivers of strong sustainability. The paper suggests some policy implications for averting disasters like fire hazards and terror attacks in high-rise residential buildings.

Persistent cervical infection with high-risk Human papillomaviruses (hrHPVs) is a necessary, but not sufficient, condition for the development of cervical cancer. Therefore, there are other co-factors facilitating the hrHPV carcinogenic process, one of which is smoking. In order to assess the effect of smoking on high-risk (hr) HPV DNA positivity and on the expression of HPV E7 oncoprotein, as a surrogate of persistent hrHPV infection, we used data from women recruited for the PIPAVIR project, which examined the role of E7 protein detection in cervical cancer screening. Women were tested for hrHPV DNA, using Multiplex Genotyping and E7 protein, using a novel sandwich ELISA method, and gave information on their smoking habits. Among 1473 women, hrHPV prevalence was 19.1%. The odds ratio (OR) for hrHPV positivity of smokers compared to non-smokers was 1.785 (95%CI: 1.365-2.332, p<0.001). The ORs for E7 positivity, concerning hrHPV positive women, ranged from 0.720 to 1.360 depending on the E7 detection assay used, but this was not statistically significant. Smoking increases the probability of hrHPV infection, and smoking intensity is positively associated to this increase. Smoking is not related to an increased probability of E7 protein positivity for hrHPV positive women.

Mostly populous city like Chennai is subjected to frequent flooding due to its complex nature of natural and man-made activities. From the analysis of the past records of flood events of 1943,1976,1985,2005 and 2008,it has been observed Adayar watershed is subjected to cataclysmic flooding in low-lying areas of the city and its suburbs because of inoperativeness of the local drainage system, rainfall associated with cyclonic activity, topography of the terrain, encroachments along the floodplain, hugh upstream flow discharge into the river and the highly impervious area which blocked the runoff to flow into the storm water drainage. After looking into these problems of flooding, a study have been conducted on Adayar watershed to develop a 2D hydrodynamic model for the two scenarios of existing condition of storm water drainage network and revised conditions of storm water drainage network using high resolution Lidar DEM to assess the volume of runoff with respect to time and duration on flood peaks for the two flood events of 2005 and 2015.Secondly to develop a 1D flood model to predict the river stages during peak floods using MIKE 11 for the Adayar watershed. Thirdly to integrate the coupled 1D and 2D model using MIKEFLOOD for assessing the extent of inundation in the floodplain area of Adayar river. Finally results from the integrated model have been validated and the results found satisfactory. As a part of mitigation measures, two flood mitigation measures have been adopted. One measure such as revised storm water drainage system which enhances the flood carrying capacity of the drains and results in less inundated area which solves the problem of urban flooding and second measure such as regrading the river bed which reduces the floodplain inundation around the adjacent area of the river. After adopting these measures, the river is free to flow into the sea without any blockades.

A high intake of carbohydrates, associated with obesity, is one of the major causes of fatty liver disease in humans. This study investigated how high carbohydrate intake induces fatty liver disease in Blunt snout bream (Megalobrama amblycephala). Blunt snout bream were fed a high-carbohydrate diet (HCBD) for 60 days. Their growth indices were evaluated, and the transcriptomes, metabolites, biochemistry, and histology of their blood and livers were analyzed. The final weight, weight gain, specific growth rate, and feed conversion ratio were all higher in the HCBD group than in the control group, but not significantly so (P > 0.05). The hepatosomatic index (HSI) differed significantly in the two groups (P < 0.05), and the metabolomics results showed that a high carbohydrate intake induced significant increases in plasma α/β-glucose, succinate, and tyrosine, which could increase hepatic glycogen and triglyceride. Low levels of betaine were also found in the livers of the HCBD group. The histology and blood biochemistry results suggested abnormal liver, with excessive lipid accumulation and liver damage. A transcriptome analysis and quantitative reverse transcription–PCR (RT–qPCR) indicated that the expression of the factors INSR, IRS, PI3K, PDK, AKT, ACC, IL6, AP1, ChREBP-MLX, PEPCK, and FBP in the insulin signaling pathway was significantly upregulated and that of SOCS3, GSK3β, and AMPK significantly downregulated in the HCBD. This pattern is associated with the nonalcoholic fatty liver disease (NAFLD) pathway. This study extends our understanding of how high carbohydrate causes increased fat deposition in the liver, enhanced glycolysis (α/β-glucose) in the plasma, and reduced betaine in the liver. This leads to activation of hepatocyte insulin resistance and lipogenesis by regulating the expression of genes related to fatty liver disease.

The preparation of gold nanoparticles (AuNPs) involves a variety of chemical and physical methods. These methods use toxic and environmentally harmful chemicals. Consequently, the synthesis of AuNPs using green chemistry has been under investigation to develop eco-friendly nanoparticles. One method to achieve this is the use of plant-derived phytochemicals capable of reducing gold ions to produce AuNPs. The aim of this study was to implement a facile microtitre-plate method to screen a large number of aqueous plant extracts to determine the optimum concentration (OC) to bio-synthesize the AuNPs. Several AuNPs of different sizes and shapes were successfully synthesized and characterized from seventeen South African plants. The characterization was done using Ultra Violet-Visible Spectroscopy, Dynamic Light Scattering, High Resolution Transmission Electron Microscopy and Energy-Dispersive X-ray Spectroscopy. We also studied the effects of temperature on the synthesis of the nanoparticles and measured its effect on the particle size of the synthesized AuNPs and the data showed that changes in temperatures affect the size and dispersity of the generated AuNPs. Further, some of the synthesized AuNPs were stable upon incubation with different biological solutions in vitro.

This study evaluated batch fermentation modes, namely, separate hydrolysis and fermentation (SHF), Quasi-simultaneous saccharification and fermentation (Q-SSF), and simultaneous saccharification and fermentation (SSF), and fermentation conditions, i.e., enzyme and yeast loadings, nutrient supplementation and sterilization, on high titer bioethanol production from SPORL-pretreated Douglas-fir forest residue without detoxification. The result indicated Q-SSF and SSF were obviously superior to SHF operation in terms of ethanol yield. The enzyme loading showed a strong positive correlation between enzyme loading and the ethanol yield. The nutrient supplementation and sterility was not necessary for ethanol production from SPORL-pretreated Douglas-fir. The yeast loading showed no significant influence on the ethanol yield for typical SSF conditions. The terminal ethanol titer of 43.2 g/L, or 75.1% theoretical based on glucose, mannose, and xylose theoretical was achieved when SSF was conducted at the condition of following: whole slurry solids loading of 15%, enzyme loading of 20 FPU/g glucan, 1.8 g/kg (wet) yeast loading, without nutrition supplementation and sterilization, at 38°C, on shake flask at 150 rpm for 96h. It is believed that with mechanical mixing, enzyme loading can be substantially reduced with affect ethanol yield by using a long fermentation time.

Estuaries are dynamic and resource-rich ecosystems renowned for their high productivity and ecological significance. The Rías Baixas, located in the northwest of the Iberian Peninsula, consist of four highly productive estuaries that support the region's economy through key fisheries and aquaculture activities. Numerical modelling of biogeochemical processes in the rias is essential to address environmental and anthropogenic pressures, particularly in areas facing intense human development. This study presents a high-resolution water quality model developed using Delft3D software, integrating hydrodynamic (Delft3D-FLOW) and water quality (Delft3D-WAQ) modules. Calibration and validation demonstrate the robust performance and reliability of the model in simulating critical biogeochemical processes, such as nutrient cycling and phytoplankton dynamics. The model effectively captures seasonal and spatial variations in water quality parameters, including water temperature, salinity, inorganic nutrients, dissolved oxygen, and chlorophyll-a. Of the variables studied, the model performed best for dissolved oxygen, followed by nitrates, phosphates, ammonium, silicate and chlorophyll-a. While some discrepancies were observed in inner zones and deeper layers of the rias, overall performance metrics aligned closely with observed data, enhancing confidence in the model's utility for future research and resource management. These results highlight the model's value as a tool for research and managing water and marine resources in the Rías Baixas.

(1) Background: Post-activation performance enhancement (PAPE) protocols using heavy resistance preloading may improve RSA, yet optimal preloading intensity for amateur players is still unknown. This study investigated the effects of two PAPE protocols using different preloading intensities (85% and 90% of 1RM back squat) on RSA. (2) Methods: A double-blind, randomized, two-period crossover design was used, and 18 amateur male players were included in the study. RSA was assessed using a 6 x 35m sprint protocol with 10-second rest intervals (RAST). (3) Results: While the main effect of time significantly (p=0.01, η²=0.71) influenced performance decline across all groups, there was no significant (p=0.65, η²=0.01) interaction between time and condition. Individual responses to PAPE varied, highlighting the importance of individual differences. Interestingly, the BS85% group exhibited a less pronounced decline in performance compared to the control group, while the BS90% group only showed significant differences in three sprint levels. (4) Conclusions: Our findings suggest that a lower preload of 85% of 1RM may be as adequate as a higher preload of 90% of 1RM in enhancing RSA in amateur soccer players. These results may indicate a potential fatigue-delaying effect of PAPE protocols and emphasize the importance of individualized approaches for optimizing PAPE strategies.

Mono-crop plantation widely found in the world and dominated by few species such as Eucalyptus, Pinus and Tectona. While they lack diversified product, negative to environmental service and limited forest product for local use. The experiment was designed to evaluate the impact of mixed plantings on the early growth performance of the E. globulus tree species. The treatments included one monoculture of E. globulus and a combination of the plant with three other native and one foreign tree species. In four consecutive years after plantation, height, root collar diameter, DBH and leaf/branch count were measured. Following two years of out planting, the survival rates of seedlings were determined. Destructive sampling was applied to measure biomass of E. globulus. The growth performance of E. globulus in mixed plantations was compared to that of trees produced in pure plantations. The findings showed that there were no significant variations in growth parameters across the treatments. Following two years of out planting, the survival rates of seedlings were determined. The growth performance of E. globulus in mixed plantations was compared to that of trees produced in pure plantations. The findings showed that there were no significant variations in growth parameters across the treatments. The survival rate of E. globulus was good, ranging from 75 to 96.8%. Similarly, the growth performance of E. globulus's root collar diameter was larger even if the trial did not reveal a significant difference between the treatments for height. In comparison to other treatments, the one that included junipers and E. globulus had a higher mean height throughout the course of three years (1.28, 2.53, and 6.12 meters, respectively), as well as a lower RCD in the first and third years (1.3 and 5.34 cm). At year four, E. globulus attain higher in Height and DBH with high growth rate in mixed plantations compared to pure stands. The relative yield of E. globulus in pure stands compare to mixed stands greater than 1. Above and below ground biomass and carbon density of E, globulus is comparable in all treatment. Overall, the study's findings confirm that planting E. globulus improves its mingling with the examined tree species. Such studies ought to be conducted again over a longer time frame in order to examine the effects at a later stage and recommend technologies for broader implementation.

This research paper investigates the impact of psychological interventions on student performance, specifically within the MIT Integration Bee, a prestigious mathematics competition that challenges students with advanced calculus problems. Conducted across multiple high schools in Texas, the study explores how different motivational techniques, including intrinsic and extrinsic rewards, influence test scores and overall student engagement. The research design includes a comprehensive analysis of motivational strategies, encompassing both baseline and reward-based conditions to assess their effectiveness in enhancing student performance. By examining a diverse sample of high schools from urban and suburban areas, this study aims to provide a holistic understanding of the factors that drive academic achievement in competitive settings. The results have significant implications for educational strategies, particularly in the realm of mathematics education, and highlight the potential for tailored motivational interventions to optimize student engagement and achievement. These findings contribute to the broader discourse on educational psychology, offering insights that could inform the development of more effective teaching practices and policies aimed at fostering a conducive learning environment for students across different educational contexts.

Ceratitis capitata (Wiedemann) (medfly) strongly affects Argentinean fruit production and export. Augmentative biological control using the exotic parasitoid Diachasmimorpha longicaudata (Ashmead) is currently applied. The ability to find and parasitize medfly larvae on a wide diversity of fruit host species is a key issue to be analyzed. This research assessed the effect of the physical features of fruit on the preference of foraging D. longicaudata females and the influence of varying release density on parasitoid performance as a pest mortality factor in three fruit species. Trials were performed inside field cages under semi-arid environmental conditions in Argentina's central–western fruit-growing region. Sweet orange, peach, and fig were tested. Fruits were inoculated with third-instar larvae of the Vienna-8 temperature-sensitive lethal medfly strain. Naïve, 5-d-old mated D. longicaudata females were released in cages at 20, 40, 80 and 160 parasitoid densities. The highest levels of medfly mortality and parasitoid emergence were recorded in fig and peach, although D. longicaudata also induced mortality in orange, a fruit with few physical features favorable to parasitism. The medfly mortality in all fruit host species significantly increased with increased parasitoid females released into field cages. Diachsmimorpha longicaudata has high potential as a medfly biocontrol agent.

Although flow mixing and cooling can be greatly enhanced when considering the use of Fluidic Oscillators (FO), they are more commonly employed in Active Flow Control (AFC) applications where the injected pulsating flow interacts with the boundary layer in order to usually delay its separation. In fact, prior to any FO implementation in a given application, it is essential to study the range of frequencies and amplitudes it can generate as a function of the incoming mass flow and its dimensions. This point is what is being enlightened in the present manuscript for a rather novel FO configuration. We are numerically studding a standard FO configuration in three dimensions 3D and also using a two dimensional 2D approach. After comparing the 3D and the 2D results and analyzing the main differences, we modified some of the internal dimensions of the FO in order to evaluate the variation of its dynamic performance. The present results clarify which internal dimensional modifications are more effective in generating larger output frequencies and velocity field variations. Care is taken to analyze the origin of the self sustained oscillations. In fact, the present research needs to be seen as the continuation of a former one recently published , where the effect of several Reynolds numbers as well as some different internal dimensions was considered.

Reeling from the global supply chain crisis created by the COVID-19 pandemic, the maritime industry still faces multifaceted challenges for its sustainable survival. Those challenges include shifts in trade routes, congestion at major seaports, container shortages, volatility in fuel prices, the scarcity of skilled maritime labor, and potential technical glitches stemming from digitized maritime operations. To help the maritime industry handle these challenges, this paper identifies major drivers and deterrents that affect the efficiency of ocean carriers’ performances over time using two different versions of data envelopment analysis (DEA) models and the Malmquist Productivity Index (MPI). After evaluating the operating efficiencies of multinational ocean carriers across the globe over extended periods (pre- and post-pandemic periods), we developed a benchmark standard that can guide best-in-class sustainable maritime practices.

Small and medium-sized enterprises (SMEs) face unique challenges that can be effectively addressed through the adoption of data mining and business intelligence (BI) tools. This systematic literature review scrutinizes the deployment and efficacy of BI and data mining technologies across SME sectors, assessing their impact on operational efficiency, strategic decision-making, and market competitiveness. Therefore, drawing from a methodologically rigorous analysis of 93 scholarly articles published between 2014 and 2024, the review elucidates the evolving landscape of BI tools and techniques that have shaped SME practices. It reveals that advanced analytics such as predictive modeling and machine learning are increasingly being adopted, though significant gaps remain, particularly shaped by economic factors. The utilization of BI and data mining enhances decision-making processes and enables SMEs to adapt effectively to market dynamics. Despite these advancements, SMEs encounter barriers such as technological complexity, high implementation costs, and substantial skills gaps, impeding effective utilization. Our review, grounded in the analysis of business intelligence tools used indicates that dashboards (31.18%) and clustering techniques (10.75%) are predominantly utilized, highlighting their strategic importance in operational settings. However, a considerable number of studies (66.67%) do not specify the BI tools or data mining techniques employed, pointing to a need for more detailed methodological transparency in future research. The predominant focus on the ICT and manufacturing sectors underscores the industrial context sector specific applicability of these technologies, with ICT accounting for 45.16% and manufacturing 22.58% of the studies. We advocate for targeted educational programs, development of user-friendly and cost-effective BI solutions, and strategic partnerships to facilitate knowledge transfer and technological empowerment in SMEs. Empirical research validating the impacts of BI and data mining on SME performance is crucial, providing a directional pathway for future academic inquiries and policy formulation.

Modular inversion on large operands is a time-consuming calculation used in elliptic curve cryptography. Its hardware implementation requires extensive hardware resources such as lookup tables and registers. We investigate state-of-the-art modular inversion algorithms and evaluate the performance and cost of the algorithms and their hardware implementations. We then propose a high-radix modular inversion algorithm aimed at short execution time and low hardware cost. We present a detailed radix-8 hardware implementation based on 256-bit primes in Verilog HDL and compare its cost performance with other implementations. Our implementation on the Altera Cyclone V FPGA chip uses 1227 ALMs (Adaptive logic modules) and 1037 registers. The modular inversion calculation takes 3.67 microseconds. The AT (Area time) factor is 8.30, outperforming other implementations. We also present an implementation of elliptic curve cryptography using the proposed radix-8 modular inversion algorithm. The implementation results also show that our modular inversion algorithm is more efficient in area time than other algorithms.

Selection is a fundamental interaction element in Virtual Reality (VR) and 3D user interfaces (UIs). Raycasting, one of the most common object selection techniques, has been known to have difficulties in selecting small or distant objects. Meanwhile, recent advancements in computer vision technology have enabled seamless vision-based hand tracking in consumer VR headsets, enhancing accessibility to freehand mid-air interaction and highlighting the need for further research in this area. This study proposed a new technique called TouchView which utilizes a virtual panel with a modern adaptation of the Through-the-lens metaphor to improve freehand selection for VR UI. TouchView enables faster and less demanding target selection by allowing direct touch interaction with the magnified object proxies reflected on the panel view. Repeated-measures ANOVA on the results of a follow-up user experiment on multitarget selection with 23 participants showed that TouchView outperformed the current market-dominating freehand raycasting technique, Hybrid Ray in terms of task performance, perceived workload, and preference. The user behavior was also analyzed to understand the underlying reasons for these improvements. The proposed technique can be used in VR UI applications to enhance the selection of distant objects, especially for cases with frequent view shifts.

Cyber-physical testing has been applied for a decade in hydrodynamic laboratories to assess the dynamic performance of floating wind turbines (FWT). Rotor loads, computed by a numerical simulator fed with measurements, are applied in real time on the physical floater by using actuators. The present paper proposes a set of short and targeted benchmark tests that aim at quantifying the performance of actuators used in cyber-physical testing of FWT. They aim at ensuring good load tracking over all frequencies of interest, and satisfactory disturbance rejection for large motions. These benchmark tests are exemplified on two radically different 15MW FWT models tested at SINTEF Ocean.

Supplier diversity initiatives in procurement have emerged as strategic imperatives for organizations aiming to enhance competitiveness and foster socio-economic equity. This research investigates the impact of supplier diversity initiatives across various industries, analyzing implementation strategies, challenges, and outcomes through a mixed-methods approach. Qualitative data, including interviews with procurement professionals and case studies of exemplary organizations, reveal diverse approaches to implementing supplier diversity—from formalized programs with dedicated resources to ad hoc initiatives driven by regulatory compliance or social responsibility goals. Challenges identified include the identification and qualification of diverse suppliers, scalability issues, and internal resistance within procurement teams. Quantitative analysis of survey data highlights positive impacts on organizational performance metrics, such as procurement spend allocation towards diverse suppliers, supplier-driven innovation, and enhanced supply chain resilience. Best practices in successful supplier diversity programs underscore strategic alignment with overall procurement strategies, effective supplier relationship management, and strong leadership commitment. Socio-economic impacts encompass economic inclusion, community engagement, and skills development among diverse supplier networks, contributing to local economic growth and broader social benefits. Despite these benefits, challenges remain in measuring qualitative outcomes and overcoming systemic barriers to implementation. Cultivating an inclusive organizational culture and leveraging leadership support are crucial for sustaining supplier diversity efforts. Continued collaboration and innovation in supplier diversity practices are recommended to maximize benefits and drive meaningful socio-economic impact globally.

This qualitative study explores the intricacies of building sustainable supplier relationships in the e-commerce sector, focusing on best practices and strategic approaches. Through in-depth interviews with procurement managers, supply chain experts, and supplier representatives, the research identifies four critical themes: trust, technology integration, ethical practices, and performance measurement. Trust is found to be the foundation of effective supplier relationships, fostering open communication and collaboration, which are essential for addressing challenges and co-creating solutions. The integration of digital technologies such as supply chain management software, blockchain, and the Internet of Things significantly enhances transparency, decision-making, and operational efficiency, providing a competitive edge. Ethical practices, including adherence to fair labor standards and environmental sustainability, are increasingly crucial as consumer and regulatory expectations evolve, necessitating alignment between e-commerce companies and their suppliers. Performance measurement and continuous improvement are vital for maintaining quality and efficiency, with clear metrics and regular evaluations driving constructive feedback and optimization of supply chain processes. The study underscores the interdependence of these elements in fostering resilient and adaptable supplier relationships. The findings offer practical guidance for e-commerce businesses and suppliers, emphasizing the need for a holistic approach to supplier management that balances trust, technology, ethics, and performance. This approach not only enhances operational effectiveness but also ensures the long-term sustainability of supplier relationships in the dynamic e-commerce landscape. The research contributes to the theoretical understanding of supplier relationship management, providing a comprehensive framework for future studies and practical applications in the e-commerce industry.

The present study is to address performance of the dairy supply chain and emphasizes the significance of reliability of the chain as a fundamental and critical attribute for fulfilling the safety requirements. In order to evaluate the performance of the dairy supply chain, the present study utilizes the reliability attribute, which is an essential and informative system performance indicator. The study considers not only the inputs and outputs but also internal activities and relationships between customers, manufacturers, and suppliers. To minimize calculations and resolve uncertainties and vagueness that may be experienced in the performance evaluation process, this study proposes the use of the Fuzzy Inference System (FIS) approach and evaluates the reliability at each level of the supply chain: supply, manufacturing, and distribution. Combining the reliability of different levels, the study finally calculates the reliability of the entire supply chain. The proposed methodology offers a practical approach for evaluating the reliability performance of a dairy supply chain and can be easily extended to other industries as well. To verify the proposed methodology, a real case in the Iranian dairy industry is chosen to be studied. Results indicate that the proposed methodology can effectively identify bottlenecks or weaknesses in the dairy supply chain and help develop effective strategies to address them. Analyzing factors influencing supply chain reliability can optimize operations, reduce costs, and improve the overall quality of dairy product quality delivered to consumers.

This study builds on our previous Systematic Literature Review (SLR) that assessed the applications and performance of zk-SNARK, zk-STARK, and Bulletproof Non-Interactive Zero-Knowledge Proof (NIZKP) protocols. To address identified research gaps, we designed and implemented a benchmark comparing these three protocols using a dynamic MiMC hash application. We evaluated performance across four general-purpose programming libraries and two programming languages. Our results show that zk-SNARK produced the smallest proofs, while zk-STARK generated the largest. In terms of proof generation and verification times, zk-STARK was the fastest, and Bulletproof the slowest. Interestingly, zk-SNARK proofs verified marginally faster than zk-STARK, contrary to other findings. These insights enhance our understanding of the functionality, security, and performance of NIZKP protocols, providing valuable guidance for selecting the most suitable protocol for specific applications.

This research examines sustainable approaches in academic career development by analyzing the interactions between job satisfaction, professional commitment, and research performance among early-career researchers in Romanian institutions. Using a quantitative cross-sectional design, data were collected from 96 individuals classified as R1 and R2 by the European Commission. A detailed questionnaire and Web-Assisted Personal Interviewing (WAPI) identified key relationships. Findings show a significant positive correlation between job satisfaction and research perfor-mance, underscoring the role of professional satisfaction in fostering sustainable academic ex-cellence. Professional commitment is also a crucial predictor of research performance, aligning with existing studies and highlighting the importance of sustainable career practices. Statistical analysis via SPSS version 23.0 validated the initial hypotheses, emphasizing each dimension's significance in a sustainable academic career. Results reflect Romania's research environment, emphasizing the need for sustainable working conditions, effective research evaluation, sup-portive career frameworks, and strong professional commitment to motivate young researchers. This research proposes innovative, sustainable practices for enhancing academic performance and career management, advocating clear objectives, leadership development, continuous competency improvement, and a collaborative, inclusive work environment. Understanding these factors aids individuals and institutions in making informed decisions that support sustainable academic career trajectories and professional growth.

This article investigates the effectiveness of feature extraction and selection techniques for enhancing the performance of classifiers accuracy in Type II Diabetes Mellitus (DM) detection using microarray gene data. To address the inherent high dimensionality of the data by employing three Feature Extraction (FE) methods are used namely, Short-Time Fourier Transform (STFT), Ridge Regression (RR), and Pearson Correlation Coefficient (PCC). To further refine the data, meta-heuristic algorithms like Bald Eagle Search Optimization (BESO) and Red Deer Optimization (RDO) are utilized for feature selection. The performance of seven classification techniques such as Non-Linear Regression - NLR, Linear Regression - LR, Gaussian Mixture Model - GMM, Expectation Maximization - EM, Logistic Regression - LoR, Softmax Discriminant Classifier - SDC, and Support Vector Machine with Radial Basis Function kernel - SVM-RBF are evaluated with and without feature selection. The analysis reveals that the combination of PCC with SVM-RBF achieved a promising accuracy of 92.85% even without feature selection. Notably, employing BESO with PCC and SVM-RBF maintained this high accuracy. However, the highest overall accuracy of 97.14% was achieved when RDO was used for feature selection alongside PCC and SVM-RBF. These findings highlight the potential of feature extraction and selection techniques, particularly RDO with PCC, in improving the accuracy of DM detection using microarray gene data.

Context: In Software Engineering, there must be clarity in communication among interested parts to elicit the requirements aimed at software development through frameworks to achieve the behaviors expected by the software. Problem: Lack of clarity in the requirements elicitation stage can impact subsequent stages of software development. Solution: We proposed a case study to achieve the proposed goal focusing on the performance efficiency characteristic expressed in the ISO/IEC/IEEE 25010 Standard using Behavior-Driven Development (BDD). Method: The case study was performed with professionals who use BDD to elicit the non-functional requirements of a company that develops software. Summary of Results: The results obtained were aspects related to the elicitation of non-functional requirements aimed at the performance efficiency characteristic of the ISO/IEC/IEEE 25010 Standard using BDD through the point of view of industry professionals. Contributions and impact: The article’s main contribution is to demonstrate the effectiveness of using BDD to elicit non-functional requirements about the performance efficiency characteristic of the ISO/IEC/IEEE 25010 Standard.

The rapid evolution of technology has reshaped the global economy, intensifying competition and prompting industry players to embrace innovation for sustained competitiveness. In Indonesia, Business Incubators, overseen by Universities and Provincial/City Governments, are pivotal. However, understanding the determinants of Business Incubator Performance remains limited. This study investigates 24 statement items aiming to uncover the factors influencing Technology Business Incubators in Indonesia, with a focus on knowledge management as a mediating variable derived from a knowledge-based perspective. Employing a quantitative approach, Structural Equation Modeling (SEM) is utilized to scrutinize these factors' impact on Business Incubator Performance. The findings reveal that knowledge management fully and partially mediates between funding support, government assistance, incubator governance, and Business Incubator Technology Performance. This research offers valuable insights for entrepreneurs and stakeholders, emphasizing the significance of funding, governmental backing, incubator governance, and knowledge management in enhancing Incubator Business Technology Performance in Indonesia.

This study investigates the impact of real-time emotional feedback on the quality of teamwork conducted over videoconferencing. We developed a framework that provides real-time feedback through a virtual mirror based on facial and voice emotion recognition. In an experiment with 28 teams (84 participants), teams collaborated over Zoom to set up a virtual Mars station using custom simulation software. Participants were divided into 14 experimental teams which were shown the virtual mirror, and 14 control teams without it. Team performance was measured by the improvement in the Mars simulation output quality. Our analysis using correlation, multilevel regression, and machine learning revealed that fewer interruptions but an increasing number over time correlated with higher performance. Higher vocal arousal and happiness also enhanced performance. We confirmed that female presence in teams boosts performance. SHAP values indicated that high variability in happiness, head movement, and positive facial valence—an “emotional rollercoaster”—positively predicted team performance. The experimental group outperformed the control group, suggesting that virtual mirroring improves virtual teamwork and that interrupting each other more, while speaking less, leads to better results.

The purpose of this research is to examine the benefits and limitations of implementation of novel digital academic advising systems using automated collection and reporting processes for ABET student outcomes data based on principles of authentic OBE for effective developmental advising. We examine digital developmental advising models of undergraduate engineering programs in two universities that employ customized features of the web-based software EvalTools® - Advising Module based on assessment methodology incorporating the Faculty Course Assessment Report, Performance Indicators and hybrid rubrics classified according to the affective, cognitive and psychomotor domains of Bloom’s learning model. A case study approach over a six-year period is adopted for this research. The two case studies present results of samples of developmental advising activity employing sequential explanatory mixed methods models using a combination of quantitative and qualitative analyses of a) detailed students’ outcomes and Performance Indicators information; and b) self-evaluation of their professional development and lifelong learning skills. The findings of this study show that digital advising systems employing the Faculty Course Assessment Report using Performance Indicators and hybrid rubrics can provide comprehensive and realistic outcomes data to help both developmental advisors and students easily identify the specific cause of performance failures, implement practical recommendations for remedial actions and track improvements. Inherent strong skills can also be identified in academically weak students by observing patterns or trends of relatively better performing outcomes to reinforce natural affinity for learning specialized competencies and pursue related and successful career paths.