To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

UV-digital printing belongs to the commonly used method for custom large-area substrate decoration. Despite low surface energy and adhesion, transparent polymer materials, such as polymethylmethacrylate (PMMA) and polycarbonate (PC), represent an ideal substrate for such purposes. The diffuse coplanar surface barrier discharge (DCSBD) in a novel compact configuration was used for substrate activation to improve ink adhesion to the polymer surface. This industrially applicable version of DCSBD was prepared, tested, and successfully implemented for the UV-digital printing process. Furthermore, wettability and surface free energy measurement, X-ray photoelectron spectroscopy, atomic force and scanning electron microscopy evaluated the surface chemistry and morphology changes. The changes in adhesion of the surface and of ink were analyzed by a peel-force and a crosscut test, respectively. A short plasma treatment (1-5 s) enhanced the substrate's properties of PMMA and PC while providing the pre-treatment suitable for further in-line UV-digital printing. Furthermore, we did not observe damage or significant change of roughness affecting the substrate's initial transparency.

Crystalline silicon nanomembrane (Si NM) is promising in wearable and implantable bioelectronics due to its electrical and mechanical performances. However, the current explorations are not enough to firmly bridge ultrathin encapsulation strategies with high performance crystalline Si NM based transistors. In this work, we utilized Al2O3/alucone as the ultrathin encapsulation strategies aim to thoroughly investigate the effect of gate dielectric surface area on the electrical performance of crystalline Si NM based metal-oxide-semiconductor capacitors (MOSCAPs). The comparative analysis was implemented on the three types of diameters (Ø) MOSCAPs with and without Al2O3/alucone encapsulation under planar and concave/convex bending conditions. Benefited from the Al2O3/alucone ultrathin encapsulations, the stability of gate leakage current density, and interfacial characteristics were maintained and improved under mechanical bending deformations for MOSCAPs with predefined Ø of 160, 240, and 320 μm compared to the bare MOSCAPs. Combined with the Ø-related mechanical analysis on the maximum strain in the critical layers and the practical measurements, the encapsulated MOSCAPs with Ø 160 μm showed the most stable electro-mechanical performances. The variations for encapsulated MOSCAPs with three types of Ø emerged in the oxide layer and the interface at dielectric/Si NM that were carefully evaluated according to the bending deformations. These findings are significant for leveraging the practical applications in the ultrathin encapsulation strategies for reliable operations of crystalline Si NM based integrated circuits (ICs).

We use COMSOL Multiphysics software to model optical processes in media and the effects of light propagation in whispering gallery mode resonators (WGMRs). Although plane wave irradiating on resonator does not create resonances, it was shown that they can be obtained when focused tangentially on the perimeter of the resonator. We demonstrate that resonances can be excited in resonators by prism coupling when the incident angle of the light is larger than the angle of total internal reflection. We determined the optimal distance between the prism and the resonator to get the strongest resonances. Bio-sensing principle of WGMRs is shown by demonstrating that the shift of resonances increases with a larger number of "bio-molecules" attached to the surface of WGMR. Surface functionalization and surface roughness were explored.

Experimental investigations were conducted to uncover the impact of cavitation control - through the use of riblets (mesoscale surface structuring) - on cavitating flows around a circular cylinder. First, the dynamics of cavitation in the flow behind a finite cylinder (without riblets) was unveiled by visualizing the cavitation clouds and measuring the lift force fluctuations acting on the cylinder. Second, as a significant step forward, a comprehensive explanation was provided for the mechanism of cavitation control using two bio-inspired riblet morphologies positioned in different orientations and locations on the cylinder. For the first time, the effects of these tiny structures on the flow dynamics and the associated cavitation process were scrutinized. This showed that scalloped riblets, with their curved design, induced secondary vortices near their tips and distorted primary streamwise vortices, and that high velocity gradients near the jagged pattern peaks of sawtooth riblets delayed flow separation, which affected cavitation.

The bacterial adhesion to food contact surfaces is a threat to human health, as these surfaces can serve as a reservoir of pathogenic bacteria. Escherichia coli is a biofilm-forming bacterium involved in surface contamination. Despite the application of disinfection protocols, contamination continues to occur. Hence, new effective and sustainable approaches are needed. Bacteriophages (or simply phages), viruses that only infect bacteria, have proven to be effective in reducing biofilms. Here, phage phT4A was applied to prevent and reduce E. coli biofilm on plastic and stainless steel. The assays were performed in Tryptic Soy Broth (TSB), at 25 °C. The biofilm formation capacity of phage-resistant and sensitive bacteria, after treatment, was also evaluated. Maximum reductions on E. coli biofilm of 5.5 log colony forming units (CFU)/cm2 (after 6 h) and 4.1 log CFU/cm2 (after 9 h), on plastic and stainless steel, respectively, were observed. In the prevention assays, phage prevented biofilm formation in 3.2 log CFU/cm2, after 12 h. Although the emergence of phage-resistant bacteria has been observed during phage treatment, a lower biofilm formation capacity was observed by phage-resistant bacteria comparatively to phage-sensitive bacteria. Overall, phages have shown to be a promising approach to decontaminate food handling surfaces.

In this paper, a swarm trajectory planning method is proposed for multiple autonomous surface vehicles (ASVs) in an unknown and obstacle-rich environment. Specifically, based on the point cloud information of the surrounding environment obtained from local sensors, a kinodynamic path searching method is used to generate a series of waypoints in the discretized control space at first. Next, after fitting B-spline curves to the obtained waypoints, a nonlinear optimization problem is formulated to optimize the B-spline curves based on gradient-based local planning. Finally, a numerical optimization method is used to solve the optimization problems in real-time to obtain collision-free, smooth and dynamically feasible trajectories relying on a shared network. Simulation results demonstrate the effectiveness and efficiency of the proposed swarm trajectory planning method for a network of ASVs.

The two-scale method (TSM) is an effective approach to simulate electromagnetic (EM) scattering from rough sea surface, to interpret physical interaction of EM wave with rough sea surfaces. The sea surface roughness spectrum and the cutoff wavenumber are two key factors affecting the accuracy of TSM simulation. This paper takes the geophysical model functions (GMFs) of different band as reference, and quantitatively studies the two factors based on the numerical simulation of different polarization backscattering coefficients. The numerical simulation demonstrates that Apel spectrum is more suitable for the backscattering simulation in C/X/Ku-band, and the optimal cutoff wavenumbers are also derived for TSM simulation of EM scattering in C/X/Ku-band. Then an empirical model function of optimal cutoff wavenumbers with respect to frequency, incident angle and wind speed are obtained with regression method. Finally, the simulation results with the new model function of cutoff wavenumber are compared with the GMF and measured data in different bands and they are all consistent. Moreover, a physical explanation for the optimal cutoff wavenumber is also given.

The peculiar physicochemical features of deep eutectic solvents (DESs), in particular their tunability, make them ideal media for various applications. Despite their ability to solubilize metal oxides, their use as rust removers from valuable substrates has not yet been thoroughly investigated. In this study we chosen three known DESs, consisting of choline chloride and acetic, oxalic or citric acid for evaluating their ability to remove corrosion products from a cellulose-based material as linen fabric and two different lithotypes, as travertine and granite. The artificial staining was achieved by placing a rusty iron grid on their surfaces. The DESs were applied by means of cellulose poultice on the linen fabrics, while on the rusted stone surfaces with a cotton swab. Macro- and microscopic observations, colorimetry and SEM/EDS analysis were employed to ascertain the cleaning effectiveness and the absence of side effects on the samples after treatment. Oxalic acid-based DES was capable of removing rust stains from both stone and cellulose-based samples, while choline chloride/citric acid DES was effective only on stone specimens. The results suggest a new practical application of DESs for the elimination of rust from lithic and cellulosic substrates of precious and artistic value.

Traditional methods of non-metallic materials joining for industrial uses are limited to lasers, or induction or conduction heating. The precision and efficiency for large-scale applications are difficult to be achieved at the same time. Here in this paper, we report a precise microwave welding method induced by localized surface plasmon of metallic macro-gaps under microwave excitation. The proposed method utilizes energy from well-developed commercial microwaver, and benefits from the precision of localized surface plasmon, an oscillating electron cloud excited by electromagnetic waves, which is currently under hot investigation only at micro- or nano-scales. The method is applied to the welding of polymers to solve the problems of complex processing equipment and high processing energy consumption in the traditional welding process, so as to cope with the growing energy and environmental crisis. Finite element numerical simulations are used to study the distribution characteristics of electric fields and temperature fields. The results show that the process is a high quality, efficient, low consumption and environmentally friendly green process compared to traditional polymer welding methods.

Membrane filtration is a popular choice in the treatment of wastewater for reuse. However, when used to produce clean water, these devices are subject to concentration polarization and fouling, which inhibit their ability to operate efficiently and provide high-quality permeate streams. Patterned membrane surfaces offer a hydrodynamic approach to mitigating concentration polarization and the surface fouling that follows. However, when subject to a steady feed flow rate, surface patterns generally produce stagnant zones in cavity-like spaces where particulate from the bulk flow recirculates in stationary vortices. To prevent aggregation in these recirculation zones, and therefore the onset of surface fouling, we study a rapidly pulsed feed flow. When combined with cavity-like geometries, such as the valleys present in membrane surface patterns, a rapidly pulsed flow generates mixing mechanisms (i.e., the deep sweep and the vortex ejection) that disrupt otherwise stagnant regions. First, we confirm the existence of these mechanisms, which are typically induced in impermeable cavities at relatively low Reynolds numbers, for near transitional feed Reynolds numbers in permeable cavity spaces via numerical simulation of the flow field. Following this confirmation, we demonstrate the ability of these mechanisms to remove particles trapped in recirculation zones via massless particle tracking studies. The results of this work suggest that when combined with a rapidly pulsed inlet flow, patterned membrane surfaces can not only alleviate concentration polarization and the surface fouling that follows but also reduce the need for traditional cleaning methods, which require operational downtime and often involve the use of abrasive chemical agents.

Milling machines have made denture fabrication possible with high accuracy in a short time. However, the relationship between the milling conditions, accuracy, and milling duration has not been clarified. This study aimed to clarify the effects of milling conditions on surface roughness and milling duration. The specimen was designed using a CAD software, and milled using PMMA disks. In milling, the parameters of finishing the specimen surface were adjusted. Three different spindle speeds and four different feed rates were set. Twelve combinations of each parameter were used for milling, and the surface roughness and milling duration were measured. Results showed that the surface roughness significantly increased with the feed rate on the slopes of the specimen. The surface roughness differed with the spindle speed on the left and right slopes. The spindle speed and feed rate did not affect the surface roughness on the flat surface. The milling duration was not affected by spindle speed but decreased as the feed rate increased. In conclusion, by increasing both the spindle speed and feed rate, the milling duration could be shortened while maintaining a constant surface quality. The optimum milling conditions were a spindle speed of 40,000 rpm and feed rate of 3,500 mm/min.

The development of integrated, compact, and multifunctional photonic circuits is crucial to increase the capacity of all-optical signal processing for communications, data management or microsystems. Plasmonics brings compactness to numerous photonic functions, but its integration into circuits in not straightforward due to insertion losses and poor modes matching. The purpose of this article is to detail the integration strategies of plasmonic structures on dielectric waveguides, and to show through some examples the variety and the application prospect of integrated plasmonic functions.

This work investigates the influence of ground albedo on the solar radiation obtained by surfaces mounted on fixed-tilt to south, one-axis, and two-axis systems. To do this, estimation of the solar radiation difference is performed by applying real albedo and zero albedo. This is done within Saudi Arabia, at 82 selected sites. Annual, seasonal, and monthly mean solar energy differences are computed as function of the site’s number, latitude, and local near-real ground albedo. The great variation in the ground-albedo values at the 82 sites (0.1 - 0.46) could be thought as having a significant effect on the solar radiation levels received on the 3 tracking modes. The analysis shows quite the opposite; a zero-albedo ground diminishes solar radiation levels by 1.43%, 3.50%, and 3.20%, respectively for the 3 modes. Therefore, in most solar engineering applications a ground albedo of 0.2 (considered as reference) can be used without losing accuracy. This is the main conclusion of the study, which must, however, be applied with caution in areas with snow cover, especially for mode-III tracking systems. In such situations the increase in solar radiation levels may be up to 15% (but ≈3.5% for mode-I and -II systems instead).

The intensification of conflicts associated with the use of water in the transition region of the Cerrado and Amazon biomes caused by population and economic growth, combined with the interest in generating energy from hydroelectric plants, raise the need to quantify the surface water availability of rivers contributing with different drainage areas. The present study estimated and compared loco measurements of liquid flow (QL) and depth of rivers in the Teles Pires river basin by reference methods (MLN-7 hydrometric windlass and metal rod/winch) and by Acoustic Current Profiler by Doppler Effect (ADCP RiverRay), in addition, evaluated the total measurement time underestimation uncertainty by ADCP. Field measurements were carried out at monthly intervals between March 2020 and October 2021, seeking to represent the water seasonality and depth and QL variations in the cross-sections of the Caiabi 1 and 2, Celeste, Preto and Renato rivers. The evaluated rivers had a net flow between 3.48 and 60.78 m3 s-1 by the windlass and between 2.66 and 54.30 m3 s-1 by the ADCP, while the depths obtained were from 0.17 to 6.34 m by the rod/winch and from 0.65 to 6.20 m by the ADCP. The methods resulted in similar measurements of net flow and depth in each of the cross-sections, and the statistical performance of the linear regression model was satisfactory with a Willmott concordance index of 0.9977 and 0.9819 for estimates of QL and of the depth of the cross-sections, respectively. The ADCP accurately measured net discharge and depth in shallow (up to 6.5 m) cross-sections of Teles Pires River in relative to the reference method. Determining the total measurement time and pairs of transects to obtain accurate QL by ADCP depends on the hydraulic characteristics of the watercourses.

Digital Image Correlation (DIC) is an optical technique used to measure surface displacements and strains in materials and structures. This technique has demonstrated significant utility in structural examination and monitoring. This manuscript offers a comprehensive review of contemporary research and applications that have leveraged the DIC technique in laboratory-based structural tests. The reviewed works encompass a broad spectrum of structural components, such as concrete beams, columns, pillars, masonry walls, infills, composite materials, structural joints, steel beams, slabs, and other structural elements. These investigations have underscored the efficacy of DIC as a metrological instrument for precise quantification of surface deformation and strain in these structural components. Moreover, the constraints of the DIC technique have been highlighted, especially in scenarios involving extensive or complex test configurations. Notwithstanding these constraints, the DIC methodology has validated its effectiveness as a strain measurement instrument, offering numerous benefits such as non-invasive operation, full-field measurement capability, high precision, real-time surveillance, and compatibility with integration into other measurement instruments and methodologies.

This article is a logical continuation of the work of Nuritdinov et al. (2021). We analyzed space observations of the apparent surface density of 81 globular clusters (GCs) observed by GAIA DR2 and published in de Boer et al (2019). First, we studied the features of the quality of the GC surface density data, including comparing them with the HST data. Using our 3-parameter model, previously tested on the example of HST space observations, we found the values of the stellar concentration parameter towards the center of the cluster. As a result, we found good correlations of this parameter with the physical characteristics of the GCs. We have also found the corresponding empirical formulas for this parameter.

The mechanism of anionic/cationic combination collector ST-8 for the efficient separation of spodumene and feldspar was investigated by flotation tests, surface tension measurements, zeta potential measurements and infrared spectroscopy analysis. The flotation results indicated that when the optimum molar combination of sodium oleate and dodecylamine was 6:1-10:1 and pH=8.5 or so, the recovery of spodumene reached a maximum of 80% and that of feldspar reached about 24.5%. Zeta potential measurements showed that the negative shift of the kinetic potential on the surface of spodumene was much stronger than that on the surface of feldspar, indicating that the adsorption capacity of the combined collector on spodumene surface and feldspar surface was greatly different. From the surface tension as well as the synergistic parameters, there was a strong mutual attraction between dodecylamine and sodium oleate, and there was a significant synergistic effect between them. Infrared spectroscopy indicated that the combined collector chemisorbed on the mineral surface, and the intensity of the absorption peak after the action of spodumene was much stronger than that after the action of feldspar. The solution chemistry of the combined collector revealed that at pH 8.5, the positively charged ions RNH3+ and (RNH3+)22+ in dodecylamine and the negatively charged RCOO- and (RCOO-)22- ions in oleic acid form highly reactive complexes to interact with the mineral surface by electrostatic gravitation, thus achieving efficient separation of spodumene and feldspar. Finally, from the closed circuit test results, a flotation index of 6.34% Li2O grade and 88.51% Li2O recovery was obtained.

Citrus peels are considered as a rich source of valuable biomolecules like pectin as polymer of polysaccharide acid. In this study, response surface methodology was used to optimize pectin extraction from Citrus clementina peels using citric acid as extraction solvent. The effect of parameters conditioning the extraction process and pectin yield (pH, temperature, extraction time, solid/liquid ratio, and raw material particle size) was investigated using a Box-Behnken design. The quality of the extracted pectin was assessed both chemically (moisture, ash, protein, and sugar content) and functionally (gelling power and emulsifying activity). According to the screening experiment, the factors pH, temperature, and particle size were the main factors influencing the pectin yield. The adjusted mathematical model enabled us to plot response surfaces in order to determine optimal extraction conditions. The highest production yield of pectin (26.6%) was obtained at the optimal conditions of: pH = 1.5; temperature 100 °C and particle size = 0.1 mm for an extraction time of 30min. Compared to the predicted value of 26.6%, the experimental extraction yield was about 21.4% of pectin. Concerning the functional properties, the extracted pectin has a high gelling power of 164°SAG and an emulsifying activity of 38.5%.

The present study employed a modifed QuEChERS method to systematically analyze the presence of fifteen Quinolones and seven Tetracyclines antibiotic residues in local animal food. Additionally, a multi-level-four-factor Box-Behnken design (BBD) within the framework of Response surface methodology (RSM) was utilized to evaluate the various factors affecting the detection efficiency of the sample pretreament procedure. The optimization was performed by Design Expert®, the factors including volume of the acetonitrle, the addition of formic acid, the duration of extract and the addition of EDTA were combined to experiment design until reach an optimal solution. Finally, the sample test was conducted by ultra-high performance liquid chromatography-quadrupole-linear ion trap mass spectrometry in both multiple reaction monitoring (MRM) and enhanced product ion (EPI) scan modes on a QTRAP® 5500 instrument. The overall average recoveries from actual samples fortified with 22 antibiotics at three levels ranged from 74.7 to 122.6% based on the use of matrix-fortified calibration with the variation ranging from 2.1 to 18.2% (n=6). The limits of detection and quantification were 0.3 μg kg-1 and 1.0 μg kg-1, respectively.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

This paper presents an analysis of the sensitivity of controlling an autonomous surface object among a group of encountered objects to the inaccuracy of state control process data. For this purpose, a safe and optimal model of the control process was defined. An algorithm for determining the optimal and safe trajectory of an object, based on the multi-object game model, was developed; for comparative analysis, an algorithm for calculating only the optimal trajectory, not taking into account the maneuverability of other objects, was additionally developed. First, simulation-based studies of the algorithms enabled a comparative analysis of a number of different acceptable strategies for optimally shifting the trajectory of maneuvering objects from a single initial direction. Thereafter, the main goal of this paper was implemented: an analysis of the sensitivity characteristics of safe control, assessed with the risk of collision, both on the inaccuracy of navigation data and on the number of possible control strategies. Finally, final conclusions and a plan for further research on the subject of the paper were formulated.

With the dramatic increase in the number of mobile users and wireless devices accessing the network, the performance of the fifth generation (5G) wireless communication systems has been severely challenged. Reconfigurable intelligent surfaces (RIS), one of the potential technologies for the sixth generation (6G), has received a lot of attention. Since it is easier to deploy, consumes less power, and is inexpensive. RIS is an electromagnetic metamaterial that serves to reconfigure the wireless environment by adjusting the phase, amplitude and frequency of the wireless signal. To maximize channel transmission efficiency and improve the reliability of communication systems, the acquisition of channel state information (CSI) is essential. Therefore, an effective channel estimation method guarantees the achievement of excellent RIS performance. This paper conducts a comprehensive investigation of the existing channel estimation methods of RIS, analysis and comparison of channel model building and CSI acquisition schemes in different frequency bands, in addition to a comprehensive description of generic channel estimation methods, with a focus on the application of deep learning. Finally, we conclude the paper and provide an outlook in the future development of RIS channel estimation.

The dispersion properties of surface plasmon polaritons during propagation on metal wires with a dielectric coating in the terahertz frequency range are investigated theoretically. An analytical expression is obtained for a pulsed electric field from the solution of Maxwell equations taking into account high-order dispersion terms. The effect of the dielectric coating on the distortion of the pulse shape is analyzed. Unlike uncoated wire, the propagation of a surface plasmon pulses along a coated wire is highly dispersive. It is shown that the coating leads to the appearance of a long-chirped signal with a propagation of only a few millimeters, i.e. when a terahertz pulse propagates along a coated wire, it acquires a long oscillatory tail, the frequency of which depends on time.

In the framework of the FireStorm project, four portable weather stations were installed in the Lousã/Estrela mountain range. Given that the Portuguese Institute for Sea and Atmosphere’s sur-face network has two weather stations installed in this region, the new data allows an improved monitoring of the vertical variability of near-surface variables in this mountainous region. As most of the wildfires in mainland Portugal affect areas with complex terrain with elevations below 1200 m and major fires continue to burn overnight, it is also relevant to monitor the vertical changes of meteorological variables in the nighttime period, as these may exhibit large variability. This study provides the first assessment of the available data, with focus on the summer seasons of 2021 and 2022. The results highlight the large variability that was observed in the region and suggest that the risk of extreme fire behaviour in the nighttime period may be underestimated.

Localized surface plasmon resonance (LSPR) based sensors exhibit enormous potential in the areas of medical diagnosis, food safety regulation and environmental monitoring. While, the broadband spectral lineshape of LSPR hampers the observation of wavelength shifts in sensing processes, thus preventing their widespread applications in sensors. Here, we describe an improved plasmonic sensor based on Fano resonances between LSPR and Rayleigh anomaly (RA) in a metal-insulator-metal (MIM) meta-grating, which is constructed by silver nanoshells array, an isolation grating mask and a continuous gold film. The MIM configuration offers more freedoms to control the optical properties of LSPR, RA and the Fano resonance between them. Strong couplings between LSPR and RA form a series of narrowband reflection peaks (with a linewidth of ~20 nm in full width at half maximum (FWHM) and a reflectivity closing to 100%) within a LSPR based broadband extinction window in experiment, making the meta-grating promising for applications of high-efficiency reflective filters. While, a well-optimized Fano resonance between LSPR and RA by carefully adjusting the angles of incident light can switch such nano-device to an improved biological/chemical sensor with the figure of merit (FOM) large than 60 and capability for detecting the local refractive index changes caused by the bonding of target molecules on surface of the nano-devices. The figure of merit of hybrid sensor in detection of target molecules is 6 and 15 times higher than the simple RA and LSPR based sensors, respectively.

Blood testing is a crucial medical application. In this study, we applied Raman spectroscopy to test blood samples and obtained complete biological information, including the main components and compositions in these samples. Short-wavelength (532-nm green light) Raman scattering spectroscopy was conducted on samples of normal blood, abnormal blood in 3 types of preparation including whole blood, plasma, and serum, and the underlying information reflected by the biological characteristics detected in each sample type were analyzed. Raman spectroscopy results indicated that normal blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. Hemoglobin affects blood oxygen level. The characteristic peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. In addition, surface-enhanced Raman spectroscopy was used to collect biological signals that are difficult to obtain in conventional Raman spectroscopy, including those of small molecules such as hormones, antibodies, and enzymes. Changes in biological information collected in this manner can be used as a basis for potentially diagnosing clinical diseases.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

Abstract- Cognitive radio (CR) play an important role in improving spectral efficiency (SE) of wireless communication, meanwhile, intelligent reflecting surface (IRS) is an effective technology to improve the secrecy performance of wireless communication system by adjusting the phase shift and amplitude of channel. Thus, we consider an IRS-aided multiple-input single-output (MISO) CR systems to enhance secrecy rate, which is consists of a single eavesdropping link, a primary network containing the primary receiver (PR), and secondary network including secondary receiver (SR) and the SR transmitter (SR-TX). Specifically, we minimize the transmit power of SR subject to secrecy capacity constraint and interference temperature (IT) constraint on PR, by jointly optimizing the beamforming vector and artificial noise (AN) constraints matrix at SR-TX as well as the phase shift matrix of IRS. Numerical results show that the different values of transmit antennas at the SR-TX and the number of IRS elements can significantly decrease the transmit power under the condition of ensuring secure communication.

Microstructure evolution in metal additive manufacturing (AM) is a complex multi-physics and multi-scale problem. Understanding the impact of AM process conditions on the microstructure evolution and the resulting mechanical properties of the printed part is an active area of research. At the meltpool scale, the thermo-fluidic governing equations have been extensively modeled in the literature to understand the meltpool conditions and the thermal gradients in its vicinity. In many phenomena governed by partial differential equations, dimensional analysis and identification of important dimensionless numbers can provide significant insights into the process dynamics. In this context, a novel strategy using dimensional analysis and the method of linear least squares regression to numerically investigate the thermo-fluidic governing equations of the Laser Powder Bed Fusion AM process is presented in this work. First, the governing equations are solved using the Finite Element Method, and the model predictions are validated by comparing with experimentally estimated cooling rates, and with numerical results from the literature. Then, through dimensional analysis, an important dimensionless quantity - interpreted as a measure of heat ab- sorbed by the powdered material and the meltpool, is identified. This dimensionless measure of heat absorbed, along with classical dimensionless quantities such as Peclet, Marangoni, and Stefan numbers, is used to investigate advective transport in the meltpool for different alloys. Further, the framework is used to study the variations of thermal gradients and the solidification cooling rate. Important correlations linking meltpool morphology and microstructure evolution related variables with classical dimensionless numbers are the key contribution of this work.

The aim of this paper is to evaluate the surface concentration of nitrogen dioxide (NO2) inferred from the Sentinel-5 Precursor TROPOspheric Monitoring Instrument (S5P/TROPOMI) NO2 tropospheric column densities over Central Europe for two time periods, the summer of 2019 and the winter of 2019-2020. Simulations of the NO2 tropospheric vertical column densities and surface concentrations from the LOng-Term Ozone Simulation – EURopean Operational Smog (LOTOS-EUROS) chemical transport model are also applied in the methodology. More than two hundred in-situ air quality monitoring stations, reporting to the European Environment Agency (EEA) air quality database, are used to carry out comparisons with the model simulations and the space-borne inferred surface concentrations. Stations are separated into seven types (urban traffic, suburban traffic, urban background, suburban background, rural background, suburban industrial and rural industrial) in order to examine the strengths and shortcomings of the different air quality markers, namely the NO2 vertical column densities and NO2 surface concentrations. S5P/TROPOMI NO2 surface concentrations are inferred by multiplying the fraction of the satellite and model NO2 vertical column densities with the model surface concentrations. The estimated inferred TROPOMI NO2 surface concentrations are examined further with the altering of three influencing factors: the model vertical levelling scheme, the versions of the TROPOMI NO2 data and the air mass factors applied to the satellite and model NO2 vertical column densities. Overall, the inferred TROPOMI NO2 surface concentrations show a better correlation with the in-situ measurements for both time periods and all station types, especially for the industrial stations (R>0.6) in winter. The calculated correlation for background stations is moderate for both periods (R~0.5 in summer and R>0.5 in winter), whereas for traffic stations it improves in the winter (from 0.20 to 0.50). After the implementation of the air mass factors from the local model, the bias is significantly reduced for most of the station types, especially in winter for the background stations, ranging from +0.49% for the urban background to +10.37% for the rural background stations. The mean relative bias in winter between the inferred S5P/TROPOMI NO2 surface concentrations and the ground-based measurements for industrial stations is about -15%, whereas for traffic urban stations it is approximately -25%. In summertime, biases are generally higher for all station types, especially for the traffic stations (~ -75%), ranging from -54% to -30% for the background and industrial stations.

Impervious surface area (ISA) is a crucial indicator for quantitative urban studies. It is also important for land use land cover classification, groundwater recharge, sustainable development, urban heat island effects, and more. Spectral ISA mapping suffers from mixed pixel problems, especially with bare soil. This study aims to develop an ISA index for spatiotemporal urban mapping from common multispectral bands by reducing soil signature better than in previous studies. This study proposed a global impervious surface area index (GISAI) enhancing ISA mapping accuracy using a temporal parameter of the remote sensing (RS) dataset. Bare soil spectral reflectance shows more fluctuation than urban ISA. Therefore, the study uses minimum composites of earlier urban indices to compile minimum soil signature. It is later improved by removing water, increasing the contrast between bare soil and urban ISA and reducing bright bare soil area. This study maps the ISA of all 12 megacities using the annual RS image collection from 2021. GISAI reduced the bare soil signature and achieved an overall accuracy of 87.29%, F1-score of 0.84, and Kappa coefficient of 0.75. However, it has some limitations with grey bare soil and barren hilly areas. By limiting bare soil signature, GISAI broadens the scope of inter-urban studies globally and lengthens potential urban time-series analysis using common multispectral bands.

Artificial roughness applied to the Solar Air Heater (SAH)’s absorber plate is a popular technique to increase its total-thermal efficiency (η_(t-th)). In this paper, the influence of geometrical parameters of V-down ribs attached below the corrugated absorbing plate of SAH on the η_(t-th) has been examined. The impacts of key roughness parameters, including relative pitch p⁄e (6-12), relative height e⁄D (0.019-0.043), angle of attack α (30°-75°), and Re (1000-20000), are examined under real weather conditions. The SAH η_(t-th) roughened by V-down ribs is predicted using an in-house developed conjugate heat transfer numerical model. It has been shown that the maximum SAH η_(t-th) is 78.8%, predicted under steady-state conditions of Re = 20000, solar irradiance G =1000 W/m2, p/e = 8, e/D = 0.043, and angle =60. That is 15.7% more efficient than that of the default smooth surface. Under real weather condition, the η_(t-th) of the roughened SAH with single and double glass covers are 17.7% and 20.1%, respectively, higher than those of smooth SAH.

The rational fabrication of low-dimensional materials with a well-defined topology and functions is an incredibly important aspect of nanotechnology. In particular, the on-surface synthesis (OSS) methods based on the bottom-up approach enable facile construction of sophisticated molecular architectures unattainable by traditional methods of wet chemistry. Among such supramolecular constructs especially interesting are surface-supported metal-organic networks (SMONs), composed of low-coordinated metal atoms and π-aromatic bridging linkers differing in size, shape and functionalization scheme. In this work, the lattice Monte Carlo (MC) simulation technique was used to extract the chemical information encoded in a family of Y-shaped positional isomers coadsorbed with trivalent metal atoms on a flat metallic surface with (111) geometry. For this purpose the investigated tritopic molecules/metal atoms were carefully mapped on a triangular lattice as interconnected/isolated segments with appropriatelly embedded anisotropic interactions. Depending on the intramolecular distribution of active centers (functional groups) within the simulated molecular bricks, we observed the metal-directed self-assembly of two-dimensional (2D) openwork patterns, aperiodic mosaics and metal-organic ladders. The obtained theoretical findings could be especially relevant for the scanning tunneling microscopy (STM) experimentalists interested in a surface-assisted construction of complex nanomaterials stabilized by directional coordination bonds.

We report the strong coupling between plasmonic surface lattice resonances (SLRs) and photonic Fabry-Pérot (F-P) resonances in a microcavity embedded with two-dimensional periodic array of metal-insulator-metal nanopillars. For such a plasmonic-photonic system, we show that the SLR can be strongly coupled to the F-P resonances of both the odd- and even orders, and that the splitting energy reaches as high as 138 meV in the visible regime. We expect that this work will provide a new scheme for strong coupling between plasmonic and photonic modes.

This paper investigates the path following control problem for a unmanned surface vehicle (USV) in the presence of unknown disturbances and system uncertainties. The simulation study combines two different types of sliding mode surface based control approaches due to its precise tracking and robustness against disturbances and uncertainty. Firstly, an adaptive linear sliding mode surface algorithm is applied, to keep the yaw error within the desired boundaries and then an adaptive integral non-linear sliding mode surface is explored to keep an account of the sliding mode condition. Additionally, a method to reconfigure the input parameters in order to keep settling time, yaw rate restriction and desired precision within boundary conditions is presented. The main strengths of proposed approach is simplicity, robustness with respect to external disturbances and high adaptability to static and dynamics reference courses without the need of parameter reconfiguration.

Although lithium-ion batteries have extensively been used in various applications because of their high energy capacity, fracture and failure, the by-products of large strains and stresses caused by fast charging and discharging need yet to be addressed. The size effects on the mechanical behavior of the nano-sized structures are significant; however, the classical elasticity theory may not consider such effects. On the other hand, surface stress theory, as a robust and potential theory, is suitable in considering size effects in nano-scale structures. Therefore, in this paper, in order to involve the surface stress effects on the fracture behavior of Li-ion batteries, the following steps are taken. Firstly, a phase-field model is used to determine the evolution of the concentration profile. Subsequently, the stress distribution is obtained by using the surface stress theory combined with chemical equations for a planar electrode. Afterward, by using the weight function method for an edge crack in the plate, the stress intensity factor is derived for all time steps and possible crack lengths during the process. It is found that with increasing phase boundary thickness parameter or decreasing phase-separation phenomenon, the surface mechanics parameters become more influential. Furthermore, in the presence of positive surface stress, the diffusion-induced stress distribution decreases, which in turn reduces the stress intensity factor. In addition, in this paper, the two states of surface stress are compared either for elastic or total strain. Concerning stresses and concentrations, the results indicate a big difference at the beginning of the deintercalation process showing, in particular, 2% for stresses, but the differences diminish gradually.

The steady-state, coupled heat and mass transfer from a fluid flow to a sphere accompanied by an exothermal catalytic chemical reaction on the surface of the sphere is analysed taking into consideration the effect of thermal radiation. The flow past the sphere is considered steady, laminar and incompressible. The radiative transfer is modeled by P₀ and P₁ approximations. The mathematical model equations were discretized by the finite difference method. The discrete equations were solved by the defect correction – multigrid method. The influence of thermal radiation on the sphere surface temperature, concentration and reaction rate was analysed for three parameter sets of the dimensionless reaction parameters. The numerical results show that only for very small values of the Prater number the effect of thermal radiation on the surface reaction is not significant.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

Axial spondyloarthritis (axSpA) is a chronic rheumatic disease characterised by the presence of inflammatory back pain. In patients with chronic low back pain, the lumbar flexion relaxation phenomenon measured by surface electromiography (sEMG) differs from that in healthy individuals. However, sEMG activity in axSpA patients has not been studied. The purpose of this study was to analyse the flexion relaxation phenomenon in axSpA patients. A study evaluating 39 axSpA patients and 35 healthy controls was conducted. sEMG activity at the erector spinae muscles was measured during lumbar full flexion movements. sEMG activity was compared between axSpA patients and the controls, as well as between active (BASDAI≥4) and non-active (BASDAI<4) patients. The reliability (using intraclass correlation coefficients (ICC)), criterion validity and discriminant validity using the area Under the curve (AUC) for the inverse flexion/relaxation ratio (1/FRR) were evaluated. Significant differences (p<0.05) were observed between axSpA patients and the control group in lumbar electric activity, especially during flexion, relaxation and extension and in FRR and 1/FRR (0.66±0.39 vs. 0.25±0.19, respectively). In addition, significant differences were found between active and non-active but also between non-active and healthy subjects. The sEMG showed good reliability (ICC>0.8 for 1/FRR) and criterion validity. ROC analysis showed good discriminant validity for axSpA patients (AUC=0.835) vs. the control group using 1/FRR. An abnormal flexion/relaxation phenomenon exists in axSpA patients compared with controls. sEMG could be an additional objective tool in the evaluation of patient function and disease activity status.

Understanding the ionic channel network of proton exchange membranes, which dictate fuel cell performance, is crucial when developing proton exchange membrane fuel cells. However, itis difficult to characterize due to complicated nano structure and differing changes to their structure with different amounts of water uptake. Electrostatic force microscopy (EFM) can map surface charge distribution as nano special resolution by measuring the electrostatic force between a vibrating conductive tip and a charged surface under an applied voltage, . In this study, the ionic channel network of a proton exchange membrane is analyzed using EFM. A mathematical approximation model of the ionic channel network is first derived, to explain changes in force gradient on the surface using EFM. The phase lag of dry and wet Nafion under stepwise changes to bias voltage is then measured. Based on the model, variations in the ionic channel network of Nafion with different amounts of water uptake are analyzed numerically. The mean surface charge density of both membranes, which is connected with the ionic channel network, is calculated using the model. The results show that the difference between the mean surface charge of the dry and wet membranes is consistent with the variation in their proton conductivity.

Knowledge of the interaction between inorganic and organic phosphates with soil minerals is vital for improving the soil P fertility. To achieve an in-depth understanding we combined adsorption experiments and hybrid ab initio molecular dynamics simulations to analyze the adsorption of common phosphates, i.e. orthophosphate (OP), glycerolphosphate (GP) and inositolhexaphosphate (IHP), onto the 100 surface plane of goethite. Experimental adsorption data per mol P-molecule basis fitted to the Freundlich model show the adsorption strength increases in the order GP &lt; OP &lt; IHP, and IHP adsorption being saturated faster followed by GP and OP. Modeling results show that OP and GP form stable monodentate (M) and binuclear bidentate (B) motifs with B being more stable than M, whereas IHP forms stable M and 3M motifs. Interfacial water plays an important role through hydrogen bonds and proton transfers with OP/GP/IHP and goethite. It also controls the binding motifs of phosphates with goethite. Combining both experimental and modeling results, we propose that the B motif dominates for OP, whereas GP forms M and IHP forms a combination of M and 3M motifs. The joint approach plausibly explains why IHP is the predominant organically bound P form in soil. This study could be considered as a preliminary step for further studies for understanding the mechanisms of how microbes and plants overcome the strong IHP–mineral binding to implement the phosphate groups into their metabolism.

Ti6Al4V samples obtained by selective laser melting were subjected to acid treatment, chemical oxidation in hydrogen peroxide solution and subsequent thermochemical treatment. The effect of temperature and time of acid etching of Ti6Al4V samples on surface roughness, morphology, topography and chemical and phase composition after the thermochemical treatment was studied. The surfaces were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and contact profilometry. Pore and protrusion sizes were measured. Acid etching modified the elemental composition and surface roughness of the alloy. Temperature had a greater influence on the morphology, topography and surface roughness of samples than time. Increases in roughness values were observed when applying successive chemical oxidation and thermochemical treatment compared to the values observed on surfaces with acid etching. After the thermochemical treatment, the samples with acid etching at a temperature of 80 °C showed a multiscale topography. In addition, a network-shaped structure was obtained on all surfaces, both on their protrusions and pores previously formed during the acid etching.

Slot-die coatings are advantageous when used for coating large-area flexible devices; in particular, the coating width can be controlled, and simultaneous multi-layer coatings can be processed. Till date, the effects of ink widening and coating gap on the coating thickness have only been considered in a few studies. To this end, we developed two mathematical models to accurately estimate the coating width and thickness considering these two effects. We used root mean square deviation (RMSD) to experimentally verify the developed method. The coating width was seen to increase and the coating thickness was seen to decrease when the coating gap was increased. Experimental results showed that the estimation performances of the coating width and thickness models were as high as 98.46 % and 95.8 %, respectively. We believe that the developed models can be useful for determining the coating conditions according to the ink properties to coat a functional layer with user-defined widths and thicknesses in both lab- and industrial-scale roll-to-roll slot-die coating processes.

The article aims to present the possible use of the simple modified optical training kit as a low-cost, simple setup for high precision surface speed measurements. A measurement capability evaluation of the optical Doppler kit used for velocimetry of a fast-rotating reflecting surface is presented. To get high repeatability measurements, we modified a fibre optic interferometry training kit. By using signal processing and statistics a precision under repeatability conditions of measurements was evaluated. Expressed by the standard deviations (3σ’s) the surface velocity measurements precision below 0.2 m/s is shown. The Cg’s capability indices were also evaluated. We postulate, the electric circuit stability of the measurement system power supply is essential for a signal noise reducing process for a wide range of metrology systems. It is crucial for precision measurements.

We fabricated the nano-aperture plasmonic platforms for single molecule detection and other various applications such as infrared thermal emission device. The nano-apertures including the nanopores on the pyramid, and the nano-slits on the Au flat membrane were fabricated using a Ga ion focused ion beam drilling technique, followed by high energy electron beam irradiations dependent upon the electron beam current density. The nanopores with a few nanometer size and the nanoslit array with order of ~ 100 nm width were fabricated. Optical characteristics for the various nanoslits were examined dependent upon the slit opening width and sample thickness. The broad emission spectra from the (7x 7) slit array are obtained from spp-mediated emission in the visible and infrared region. A sharp strong infrared emission peak is also obtained due to Au nanoparticle. The fabricated Au platform can be utilized as single molecule sensor and infrared thermal emission device.

The conservation of coastal wetland ecosystems, like mangrove forests and salt marshes, represents a critical strategy for mitigating atmospheric emissions and climate change in the 21st century. Yet the existence of these environments is threatened by human-induced disturbances, namely deforestation and accelerated sea-level rise. Coastal systems maintain surface elevation in response to sea-level rise through a combination of physical and biological processes both above and below the ground surface. The quantification and relative contribution of belowground process controls (e.g., seasonal water content, organic matter decomposition) on surface elevation change is largely unexplored but crucial for informing coastal ecosystem sustainability. To address this knowledge deficit, we integrated measurements of surface elevation change of the live root zone (0.5 to 1 m depth) with geotechnical data from co-located sediment cores in the Sundarbans mangrove forest (SMF) of southwest Bangladesh. Core data reveal that the primary belowground controls on surface elevation change include seasonal fluctuations in pore-water content and the relative abundance of fine-grained sediments capable of volumetric expansion and contraction, supporting an elevation gain of ~2.42 ± 0.26 cm yr⁻¹. In contrast to many mangrove environments, the soils of the SMF contain little organic matter and are dominantly composed (>90%) of inorganic clastic sediments. The mineral-rich soil texture likely leads to less compaction-induced subsidence as compared to organic-rich substrates and facilitates surface equilibrium in response to sea level rise. Despite a relatively high soil bulk density, soil carbon (C) density of the SMF is very low owing to the dearth of preserved organic content. However, rates of C accumulation are balanced out by locally high accretion rates, rendering the SMF a greater sink of terrestrial C than the worldwide mangrove average. The findings of this study demonstrate that C accumulation in the SMF, and possibly other alluvial mangrove forests, is highly dependent on the continued delivery of sediment to the mangrove platform and associated settings.

Preclinical animal studies provide valuable opportunities to better understand human diseases and contribute to major advances in medicine. This review provides a comprehensive overview of ocular parameters in humans and selected animals, with a focus on the ocular surface, detailing species differences in ocular surface anatomy, physiology, tear film dynamics and tear film composition. We describe major pitfalls that tremendously limit the translational potential of traditional laboratory animals (ie., rabbits, mice and rats) in ophthalmic research, and highlight the benefits of integrating companion dogs with clinical analogues to human diseases into preclinical pharmacology studies. This One Health approach can help accelerate and improve the framework in which ophthalmic research is translated to the human clinic. Studies can be conducted in canine subjects with naturally occurring or non-invasively induced ocular surface disorders (eg., dry eye disease, conjunctivitis), reviewed herein, and tear fluid can be easily retrieved from canine eyes for various bioanalytical purposes. In this review, we discuss common tear collection methods, including capillary tubes and Schirmer tear strips, and provide guidelines for tear sampling and extraction to improve the reliability of analyte quantification (drugs, proteins, others).

In this study, a new approach for estimating volume variations of lakes and reservoirs using water levels from satellite altimetry and surface areas from optical imagery is presented. Both input data sets, namely water level time series and surface area time series, are provided by DGFI-TUM‘s Database of Hydrological Time Series of Inland Waters (DAHITI). The approach is divided into three parts. In the first part, a hypsometry model based on the new modified Strahler approach is computed by combining water levels and surface areas. The hypsometry model describes the dependency between water levels and surface areas of lakes and reservoirs. In the second part, a bathymetry between minimum and maximum surface area is computed. For this purpose, DAHITI land-water masks are stacked using water levels derived from the hypsometry model. Finally, water levels and surface areas are intersected with the bathymetry to estimate a time series of volume variations in relation to the minimum observed surface area. The results are validated with volume time series derived from in-situ water levels in combination with bathymetric surveys. In this study, 28 lakes and reservoirs located in Texas are investigated. The absolute volumes of the investigated lakes and reservoirs vary between 0.099 km³ and 6.448 km³. The correlation coefficients of the resulting volume variation time series with validation data vary between 0.80 and 0.99. Overall, the relative errors with respect to volume variations vary between 2.8% and 14.9% with an average of 8.3% for all 28 investigated lakes and reservoirs. When comparing the resulting RMSE with absolute volumes, the absolute errors vary between 1.5% and 6.4% with an average of 3.1%. This study shows that volume variations can be calculated with a high accuracy which depends essentially on the quality of the used water levels and surface areas. In addition, this study provides a hypsometry model, high-resolution bathymetry and water level time series derived from surface areas based on the hypsometry model. All data sets are publicly available on the Database of Hydrological Time Series of Inland Waters (DAHITI, https://dahiti.dgfi.tum.de).

According the JKR theory of adhesive contact, changes of the contact configuration after formation of the adhesive neck and before detaching are completely reversible. This means, that after formation of the initial contact, the force-distance dependencies should coincide, independently on the direction of the process (indentation or pull-off). In the majority of real systems, this invariance is not observed. The reasons for this may be either plastic deformation in the contacting bodies or surface roughness. One further mechanism of irreversibility (and corresponding energy dissipation) may be chemical heterogeneity of the contact interface leading to the spatial dependence of the specific work of adhesion. In the present paper, this "chemical" mechanism is analyzed on a simple example of an axisymmetric contact (with axisymmetric heterogeneity). It is shown that in the asymptotic case of a "microscopic heterogeneity", the system follows, during both indentation and pull-off, JKR curves, however, corresponding to different specific surface energies. After the turning point of the movement, the contact area first does not change and the transition from one JKR curve to the other occurs via a linear dependency of the force on indentation depth. The macroscopic behavior is not sensitive to the absolute and relative widths of the regions with different surface energy but depends mainly on the values of the specific surface energy.

A recently developed thermodynamic theory for the determination of the driving force of crystallization and the crystal–melt surface tension is applied to the ice–water system employing the new Thermodynamic Equation of Seawater TEOS-10. The deviations of approximative formulations of the driving force and the surface tension from the exact reference properties are quantified, showing that the proposed simplifications are applicable for low to moderate undercooling and pressure differences to the respective equilibrium state of water. The TEOS-10 based predictions of the ice crystallization rate revealed pressure-induced deceleration of ice nucleation with an increasing pressure, and acceleration of ice nucleation by pressure decrease. This result is in, at least, qualitative agreement with laboratory experiments and computer simulations. Both the temperature and pressure dependencies of the ice–water surface tension were found to be in line with the le Chatelier–Braun principle, in that the surface tension decreases upon increasing degree of metastability of water (by decreasing temperature and pressure), which favors nucleation to move the system back to a stable state. The reason for this behavior is discussed. Finally, the Kauzmann temperature of the ice–water system was found to amount TK=116K, which is far below the temperature of homogeneous freezing. The Kauzmann pressure was found to amount pK=-212MPa, suggesting favor of homogeneous freezing upon exerting a negative pressure on the liquid. In terms of thermodynamic properties entering the theory, the reason for the negative Kauzmann pressure is the higher mass density of water in comparison to ice at the melting point.

We investigate molecular beam epitaxy growth conditions of micrometers-thick In0.52Al0.48As designed for waveguide of InGaAs/InAlAs/InP quantum cascade lasers. Effect of growth temperature and V/III ratio on the surface morphology and defect structure were studied. The growth conditions which were developed for the growth of cascaded In0.53Ga0.47As/In0.52Al0.48As active region, e.g. growth temperature of TG=520°C and V/III ratio of 12, turned out to be not optimum for the growth of thick In0.52Al0.48As waveguide layers. It has been observed that after exceeding ~1µm thickness the quality of In0.52Al0.48As layers deteriorates. The in-situ optical reflectometry showed increasing surface roughness caused by defect forming, which was further confirmed by High Resolution X-Ray reciprocal space mapping, optical microscopy and atomic force microscopy. The presented optimization of growth conditions of In0.52Al0.48As waveguide layer led to the growth of defect free material, with good optical quality. This has been achieved by decreasing the growth temperature to TG=480 °C with appropriate increasing V/III ratio. At the same time the growth conditions of the cascade active region of the laser were left unchanged. The lasers grown using new recipe have shown lower threshold currents and improved slope efficiency. We relate this performance improvement to reduction of the electron scattering on the interface roughness and decreased waveguide absorption losses.

Acquisition of real-time hydraulic data is an essential component for flood forecasting. However, we frequently face difficulties in obtaining discharge data using classical contact methods during high magnitude floods and for systems experiencing rapid hydro-geomorphological adjustment. Therefore, we developed low-cost, non-contact sensors and platforms that are designed to overcome these difficulties. These advances enable flood flow properties to be monitored at multiple locations across a river catchment, at low-cost, and communicated in near real-time by using an image velocimetry method. This is an optics-based approach for stream flow measurement using commercially available near-infrared digital cameras to acquire video footage in full HD (30fps). Video footage is then subjected to optical flow tracking techniques based on cross-correlation, and feature-based tracking, enabling the displacement rates of detected features (for example natural foam, seeds, woody debris, and turbulent structures) to be computed. This manual provides step by step guidance to install an image-based gauging station. It contains the list of necessary components, the calibration process of a new camera and the assembly procedure of the system.

The Voronoi entropy is a mathematical tool for quantitative characterization of the orderliness of points distributed on a surface. The tool is useful to study various surface self-assembly processes. We provide the historical background, from Kepler and Descartes to our days, and discuss topological properties of the Voronoi tessellation, upon which the entropy concept is based, and its scaling properties, known as the Lewis and Aboav-Weaire laws. The Voronoi entropy has been successfully applied to recently discovered self-assembled structures, such as patterned micro-porous polymer surfaces obtained by the breath figure method and levitating ordered water micro-droplet clusters.

In addition to image filtering in the spatial and frequency domains, fractal characteristics induced algorithms offers considerable flexibility in the design and implementations of image processing solutions in areas such as image enhancement, image restoration, image data compression and spectrum of applications of practical interests. Facing up to a real-world problem of identifying workpiece surface defects, a generic adaptive fractal filtering algorithm is proposed, which shows advantages on the problems of target recognition, feature extraction and image denoising at multiple scales. First, we reveal the physical principles underlying between signal SNR and its representative fractal dimension indicative parameters, validating that the fractal dimension can be used to adaptively obtain the image features. Second, an adaptive fractal filtering algorithm (Abbreviated as AFFA) is proposed according to the identified correlation between the image fractal dimensions and the scales of objects, and it is verified by a benchmarking image processing case study. Third, by using the proposed fractal filtering algorithm, surface defects on a flange workpiece are identified. Compared to conventional image processing algorithms, the proposed algorithm shows superior computing simplicity and better performance Numerical analysis and engineering case studies show that the fractal dimension is eligible for deriving an adaptive filtering algorithm for diverse-scale object identification, and the proposed AFFA is feasible for general application in workpiece surface defect detection.

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO₂ with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.

Novel collector lead(II)-benzohydroxamic acid (Pb(II)-BHA) complexes in aqueous solution were characterized by using experimental approaches, including Ultraviolet-visible (UV-Vis) spectroscopy and electrospray ionization–mass spectrometry (ESI-MS), as well as first-principle density functional theory (DFT) calculations with consideration for solvation effects. The Job plot delineated that a single coordinated Pb(BHA)⁺ should be formed first, and the higher coordination number complexes can be formed subsequently. Moreover, the Pb(II)-BHA species can aggregate with each other to form complicated structures, such as Pb(BHA)₂ or highly complicated complexes. ESI-MS results validated the existence of Pb-(BHA)_n=1,2 under different solution pH values. Further, the first-principles calculations suggested that Pb(BHA)⁺ should be the most stable structure, and the Pb atom in Pb(BHA)⁺ will act as an active site to attack nucleophiles. These findings are meaningful to further illustrate the adsorption mechanism of Pb(II)-BHA complexes in mineral processing.

In this study, we applied a central composite design to estimate independent variables and establish optimal conditions of filtration rate and feces production that enhance filtration of suspended organic matter by the freshwater mussels Sinanodonta woodiana. The results indicated that statistical design methodology offers an efficient and feasible approach for high filtration and low feces production condition optimization. The proposed model equation takes into account the quantitative effect of variables and also the influence of interactions among variables on mussel filtration rate. Under the optimal experimental conditions (mussel size, 13.0 ± 0.2 cm; water current, 17.5 L/h), the experimental filtration rate of 4.47 ± 1.82 L/mussel/h showed a degree of correspondence with the predicted value of 8.4 L/mussel/h, which verified the practicability of this optimum strategy.

An adequate representation of the water infiltration process in the soil allows improving the efficiency in application and the uniformity in surface irrigation. The Green and Ampt model has shown a good representation of the process, and researchers from the United States Department of Agriculture (USDA) determined the values of their parameters for soils of that country, which are shown in tables or through functional relationships and this information is used as reference in several parts of the world, although there is no certainty that they are representative of the soils in Mexico. In this study, the parameters of the Green & Ampt equation were determined and evaluated in some soils of agricultural importance in Mexico. The parameters were obtained in four ways: one of them applied a methodology adapted from Brooks and Corey to quantify the wetting front capillary pressure head and used an permeameter under constant hydraulic head to determine the saturated hydraulic conductivity, and the other three consisted in taking them from three studies reported by the USDA. The values of the parameters suggested in Mexico drastically underestimated the results with relative errors (RE) in a range of -49.0 to -94.0% and the most representative were those obtained with the methodology proposed in this research with RE of -15.0 to 6.0%.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

After UV excitation, gas phase thymine returns to ground state in 5 to 7 ps, showing multiple time constants. There is no consensus on the assignment of these processes, with a dispute between models claiming that thymine is trapped either in the first (S1) or in the second (S2) excited states. In the present study, nonadiabatic dynamics simulation of thymine is performed on the basis of ADC(2) surfaces, to understand the role of dynamic electron correlation on the deactivation pathways. The results show that trapping in S2 is strongly reduced in comparison to previous simulations considering only non-dynamic electron correlation on CASSCF surfaces. The reason for the difference is traced back to the energetic cost for formation of a CO p bond in S2.

In this research paper a novel Ultra Violet Photo Catalyst Oxidation (UVPCO) sensor for air and surface sanitization using Common Source (CS) amplifier is presented. The ultra violet photo catalysis is the process in which the highly reactive radicals like H+, OH-and peroxides ions are produced from air in the presence of the ultra violet radiation and photo catalyst. In this process, the free radicals outbreaks the bio aerosols like bacteria, fungus and volatile organic compounds (VOCs) and destroy them. The proposed system is relies on the fast operation of PCS which operates under sub-threshold conditions and reduced computation time. The properties of common source amplifier like very high voltage gain and input output resistance increased the sensitivity as well as stability of the circuit. The system is more user friendly and the outcomes of simulation are fairly in agreement with the theoretical estimation. Keywords: bio aerosol, Photo Catalytic Oxidation (PCO), hydroxyl, hydrogen peroxide, SPICE, surface sanitizer.

Deploying onshore wind energy as a cornerstone of future global energy systems challenges societies and decision-makers worldwide. Expanding wind energy should contribute to a more sustainable electricity generation without harnessing humans and their environment. Opponents often highlight the negative environmental impacts of wind energy to impede its expansion. This study reviews 152 studies to synthesize, summarize, and discuss critically the current knowledge, research gaps, and mitigation strategies on the environmental impacts of onshore wind energy. The investigated effects comprise impacts on the abiotic and biotic environment, with birds and bats in particular, noise and visual impacts. Effects are discussed in the context of social acceptance, other energy technologies, and wind energy expansion in forests. The review illustrates that many effects are highly case-specific and must be more generalizable. Studies are biased regarding the research focus and areas, needing more standardized research methods and long-term measurements. Most studies focus on the direct mortality of birds and bats at wind farms and are concentrated in Europe and North America. Knowledge gaps persist for many impact categories, and the efficacy of mitigation strategies has yet to be proven. More targeted, unbiased research is required that allows for an objective evaluation of the environmental impacts of wind energy and strategies to mitigate them. Impacts, such as those on biodiversity, need to be addressed in the context of other anthropogenic influences and the benefits of wind energy. This forms the basis for a socially acceptable, efficient, and sustainable expansion of wind energy.

The impact of the agriculture net carbon effect is crucial for climate change mitigation, yet research on this topic in China is currently insufficient. In this study, the carbon balance ratio (CBR) is used to characterise the net carbon effect of agriculture, and the spatial Durbin model and threshold regression model were used to empirically analyse the CBR with a sample of 30 provincial-level regions in China from 2004 to 2019. The aim was to investigate the mechanism of the influence of the land management scale (SCALE) of farming on the CBR. The results of the study indicate that national farming generally has a net sink effect, with large changes in interannual fluctuations; the expansion of SCALE has an obvious role in increasing sinks and reducing emissions, and has a positive spatial spillover effect on CBR, with significant spatial heterogeneity. Furthermore, as the SCALE expands, the direction of the influence of rural residents’ income and education level on CBR changes in the opposite direction, showing a significant non-linear relationship characteristic. However, in most areas, the SCALE threshold has not yet been reached, suggesting that the improvement in education levels can still offset the negative impact of economic income growth in the short term. The study recommends paying attention to the role of farmers’ human capital, changing production methods, and implementing carbon peaking and carbon neutrality goals to enhance the net sink effect of the farming industry, which would be achieved by increasing land management scale.

Polarimetric features extracted from polarimetric synthetic aperture radar (PolSAR) images contain abundant scattering information of objects. Utilizing this information for PolSAR image classification can improve accuracy and enhance object monitoring. Although significant progress has been achieved in related research, there are still issues such as insufficient utilization of polarimetric information and features. In this paper, a deep learning classification method based on polarimetric channel power features for PolSAR is proposed. The distinctive characteristic of this method is that the polarimetric features inputted into the deep learning network are the power values of polarimetric channels, where these channels are treated equivalently and contain complete polarimetric information. In terms of experimental comparative study, besides polarimetric power combinations, three different data input schemes were employed as data for the input end of the convolutional neural network (CNN), taking into account existing research. The neural networks utilizes the extracted polarimetric features to classify images, and the classification accuracy analysis is employed to compare the strengths and weaknesses of different input schemes. It is worth mentioning that the polarized characteristics of the data input scheme mentioned in this article have been derived through rigorous mathematical deduction, and each polarimetric feature has clear physical meaning. By testing different data input schemes on the Gaofen-3 (GF-3) PolSAR image, the experimental results show that the method proposed in this article outperforms existing methods and can improve the accuracy of classification to a certain extent, validating the effectiveness of this method in large-scale area classification.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

Although crop conversion from annual to perennial crops has been considered as one path towards climate-smart and resource-efficient agriculture, the effects of this conversion on soil multifunctionality and biomass yields remain unclear. Here, we investigated the effects of one annual and three perennial crops (a grass (Lolium perenne), a legume (Medicago sativa), and their mixture) on soil multifunctionality and biomass yield on the Yellow River floodplain. Soil multifunctionality was assessed by the capacity of water regulation and the multifunctionality of carbon (C), nitrogen (N), and phosphorus (P) cycles. Results showed that perennial crops enhanced soil multifunctionality by 207% for L. perenne, 311% for M. sativa, and 438% for L. perenne + M. sativa, compared with annual winter wheat (Triticum aestivum). The effect of perennial crops on soil multifunctionality increased with infiltration rate, dissolved organic C, microbial biomass C, and extracellular enzymatic activities for both C and N acquisition. However, we observed that perennial crops had lower biomass yield than annual crop. Therefore, the transition of agricultural landscapes to perennials needs to take into account the balance between environmental protection and food security, as well as environmental heterogeneity, to promote sustainable agricultural development.

This study analyzed the CO2 capture potential for Parque Natural Regional Serrania de las Quinchas buffer area in Colombia. For this purpose, multitemporal analysis for land covering for years 1989, 2000, 2006, 2011, 2017 and 2021 was made using the Normalized Difference Vegetation Index (NDVI), and Corine Land Cover (CLC) methodology. In the same way, Aboveground Biomass (AGB) was measured for representative parcels by measuring tree’s diameters and heights and applying the adequate allometric models; carbon content in soils was measured too. Results show that dense forest has grown since 1989 and the carbon stock in all the vegetation covers increased by 14,3% from 1989 until 2021, using literature data for tropical humid forests. If measured AGB values obtained in this study are used, the carbon stock average is 3 times this value. Measured carbon average content in AGB was 374,3 Ton C/Ha, well above the average for the content reported for humid tropical forests in Colombia; carbon content in soils was 897,19 Ton/Ha, 2,4 times that found in the AGB. In total, an average of 1271,49 Ton C/Ha (AGB+ soil) was found and a pattern of dense forest recovery was found, but in a more dispersed way than in the past. A very interesting potential for existing forests recovery was found for this area. Strategies for this include the development of sustainable practices, land use management, everything pursuing biodiversity preservation and the participation and leading of the local communities.

The eco-efficiency of cultivated land use (ECLU) is an important indicator for the construction of ecological civilization in China. Exploring the spatiotemporal dynamic evolution of the ECLU is helpful for sustainable use of arable land, ensuring food security and ecological security. However, previous studies have mostly focused on the use of a slacks-based measure (SBM) model for ECLU measurement, ignoring the more accurate epsilon-based measure (EBM) model. Therefore, in this study, firstly, we explored the conceptual framework of ECLU, and then, based on the panel data of the counties in the region around Beijing and Tianjin from 2005 to 2020, we investigated the spatial and temporal evolution of ECLU by using the Super-EBM model, kernel density estimation method, and spatial Markov chain model. Results displayed: (1) From 2005 to 2020, the ECLU in the region around Beijing and Tianjin displayed an increasing state, but the average value was only 0.55. (2) The time evolution of the ECLU has gradually polarized, the internal gap has widened, but it tends to stabilize. (3) The ECLU in the region around Beijing-Tianjin was more inclined to keep it the same and there was a "club convergence" phenomenon, which was meaningfully affected by the background of neighboring areas. In the light of local conditions, the government should reasonably formulate the path to optimize the ECLU, strengthen the linkage with the surrounding cities, and bring into play the positive spillover effect.

Climate and land-use changes have been contributing to increase the occurrence of extreme wild-fires, shifting fire regimes and driving desertification, particularly in Mediterranean-climate regions. However, few studies have researched the effects of land-use change on fire regimes and carbon storage at the broad national scale. To address this gap, we used spatially explicit data from annual burned areas in mainland Portugal to build a typology of fire regimes based on the accumulated burned area and its temporal concentration (Gini index) between 1984 and 2019, which was combined with 2018 carbon stock data (above- and below-ground), and a landscape typology re-sulting from cluster analysis over land-use composition, diversity and configuration, to explore relationships between landscape types and the two major ecosystem services at stake: wildfire reduction and carbon stock. Cross tabulations, logistic and linear regressions were performed on these data and results revealed a strong relationship between landscapes dominated by maritime pine and eucalypt forest plantations and high-hazardous fire regime but hold the highest carbon stock. Shrubland-mixed landscapes were associated with lower carbon stocks but less hazardous fire regimes. Specialized agricultural landscapes, as well as mixed native forests and mixed agro-forestry landscapes, were the least associated with wildfires. In the case of agricultural landscapes however, this good wildfire performance is achieved at the cost of the poorest carbon stock, de-noting land degradation, whereas native forests and agroforestry landscapes strike the best trade-off between carbon stock and fire regime. Our findings support how nature-based solutions promoting wildfire mitigation and carbon stock ecosystem services may prevent and revert land degradation harming Mediterranean regions.

The Victorian Government Inquiry into wildfires that killed 173 people in 2009 has driven an Australian policy shift from self-evacuation or staying and defending a well-prepared property (‘go or stay’) to self-evacuation under catastrophic fire weather (‘leave early’). The Inquiry also led to the establishment of national ‘performance standards’ for Private Fire Shelters (PFS, that also known as bunkers). Nonetheless, incorporation of PFS into national bushfire policy remains embryonic with only Victoria having streamlined accreditation and planning approval processes. Arguments against PFS include potentially engendering complacency about preparing dwellings to survive fire and encourage risky behavior in response to a fire threat. Counteracting these arguments is research that shows that residents without PFS have low engagement with bushfire preparation and typically delay evacuation. In any case, because wildfire is unpredictable it is accepted that self-evacuation plans must have fallback positions that include sheltering ‘in place’ from the bushfire, making properly used and well maintained PFS an important element of bushfire safety. A less discussed barrier to PFS uptake outside Victoria appears to hinge on a lack of clarity about obligations for their design, certification, and consistency with planning approvals. The escalating Australian fire crisis demands much greater research and development in legal frameworks, policy and planning processes for PFS, as well as design and construction standards.

Economic valuations of ecosystem services often transfer previously estimated global unit values to the geographical setting of interest. While this approach produces quick results, its reliability depends on how representative the large-scale average unit values are for the given local context. Here, we estimate the values of three ecosystem services (ES) – water filtration, nutrient cycling and carbon sequestration – in the Grand River watershed (GRW) of southern Ontario, Canada. The watershed covers nearly 7000 km2, has a humid continental climate and a population of close to one million people. Land cover is dominated by agriculture. We compare ES valuations using locally derived (i.e., GRW-specific) unit values to valuations based on unit values from a regional database and those compiled in the global Ecosystem Services Valuation Database (ESVD). The regional database includes mean unit values from three case studies within southern Ontario and one boreal watershed in British Columbia. As expected, the regional database yields average monetary values for the three ES that are close to those obtained with the local unit values but with larger associated uncertainties. Using the ESVD, however, results in significantly higher monetary values for the ES. For water filtration, the ESVD value is more than five times higher than the regional and local estimates. We further illustrate the effect of the extent of aggregation of forested and agricultural land categories on the ES values. For example, by subdividing the forest category into three sub-categories (deciduous, coniferous, and mixed forest), the estimated value of the carbon sequestration ES of forested areas within the GRW increases by 15%. Overall, our results emphasize the importance of critically assessing the origin of unit values and the land cover resolution in ES valuation, especially when the latter is used as a policy-guiding tool.

As the first pilot ecological civilization zone in China, Fujian Province has an excellent ecological environment quality, and its ecological environment-related indices continue to be among the highest in the country. In order to investigate the causes of the excellent ecological quality in Fujian Province in the past 15 years, this paper selects MODIS images, land use data and provincial and municipal statistical yearbook data of Fujian province from 2005 to 2020 as data sources, evaluates the ecological system health of Fujian Province by remote-sensing ecological index (i.e. RSEI), constructs the land use intensity system of Fujian Province at the same time, and uses a coupled coordination model to analyze the coupling between RSEI and The coupled coordination model was used to analyze the coupling relationship between RSEI and land use intensity, and finally the spatial and temporal evolution of ecological health in Fujian Province from 2005 to 2020 was analyzed. The results show that the coupled coordination between land use intensity and ecosystem health in Fujian province showed a continuous increase between 2005 and 2020, especially in Ningde, where the increase was most significant, from 0.0993 to 0.963, this pattern of spatial distribution is lower in the south-eastern coastal region than in the north-western interior, higher in the south-western region than in the north-western region, and higher in the north-eastern region than in the south-eastern region. In terms of the type of role, the land use intensity of most cities in Fujian Province in 2005 played an obvious role in blocking the degree of ecosystem health, but as time changed, urban land use continued to be optimized and reached moderate or even high quality coordination with the quality of the ecological environment, but Xiamen City developed relatively slowly and its 2020 coupling degree value was 0.315, which was still in mild disorder. This study fills a gap in the research mechanism of the interaction between the degree of ecosystem health and land use intensity, and also provides a new perspective for the construction of ecological civilization and the assessment of the degree of ecosystem health in Fujian Province and the whole country.

Soil erosion is one of the most important environmental problems which can have various negative consequences, such as land degradation affecting the sustainable development and the agricultural production, especially for developing countries like Tunisia. Moreover, soil erosion is a major problem around the world because of its effects on soil fertility by nutriment loss and siltation in water bodies. Apart from this, soil erosion by water is the most serious type of land loss in several regions both locally and globally. This study evaluated regional soil erosion risk through the derivation of appropriate factors, using the Revised Universal Soil Loss Equation (RUSLE), which was applied to establish a soil erosion risk map of the whole Tunisian territory and to identify the vulnerable areas of the country. RUSLE model take into account all the factors playing a major role in erosion processes, namely the erodibility of soils, topography, land use, rainfall erosivity and anti-erosion farming practices. The equation is thus implemented under Geographic Information System (GIS) “Arc GIS Desktop”. The results indicated that Tunisia has a serious risk of soil water erosion, showing that 6.43% of the total area of the country is affected by a very high soil loss rate estimated at more than 30 t/ha/year and 4.20% are affected by high mean annual soil loss ranging from 20 to 30 t/ha/year. The most eroded areas were identified in west southern, central and western parts of the country. The spatial erosion map can be used as a decision support document to guide decision-makers towards better land management and provide the opportunity to develop management strategies for soil erosion prevention and control in the global scale of Tunisia.

This research introduces Genus-Physiognomy-Ecosystem (GPE) mapping at a prefecture level through machine learning of multi-spectral and multi-temporal satellite images at 10m spatial resolution, and later integration of prefecture wise maps into country scale for dealing with 88 GPE types to be classified from a large size of training data involved in the research effectively. This research was made possible by harnessing entire archives of Level-2A product, Bottom of Atmosphere reflectance images collected by MultiSpectral Instruments onboard a constellation of two polar-orbiting Sentinel-2 mission satellites. The satellite images were pre-processed for cloud masking and monthly median composite images consisting of 10 multi-spectral bands and 7 spectral indexes were generated. The ground truth labels were extracted from extant vegetation survey maps by implementing systematic stratified sampling approach and noisy labels were dropped out for preparing a reliable ground truth database. Graphics Processing Unit (GPU) implementation of Gradient Boosting Decision Trees (GBDT) classifier was employed for classification of 88 GPE types from 204 satellite features. The classification accuracy computed with 25% test data varied from 65-81% in terms of F1-score across 48 prefectural regions. This research produced seamless maps of 88 GPE types first time at a country scale with an average 72% F1-score. In addition, mapping of solar panels and vegetation disturbance are added.

Classification and mapping of plant communities is an essential step for conservation and management of ecosystems and biodiversity. We adopt the Genus-Physiognomy-Ecosystem (GPE) system developed in previous study for satellite-based classification of plant communities. This paper assesses the potential of multi-spectral and multi-temporal images collected by Sentinel-2 satellites. This research was conducted in five representative study sites in a temperate region. It consists of 44 types of plant communities including a few land cover types as well. The plant community types were enumerated in the study sites and ground truth data were prepared with reference to extant vegetation surveys, visual interpretation of high-resolution images, and onsite field observations. We acquired all Sentinel-2 Level-1C product images available for the study sites between 2017-2019 and generated monthly median composite images consisting of ten spectral and twelve spectral-indices. Gradient Boosting Decision Trees (GBDT) classifier was employed as an efficient and distributed gradient boosting technique for the supervised classification of big datasets involved in the research. The cross-validation accuracy in terms of kappa coefficient varied from 87% in Oze site with 41 land cover and plant community types to 95% in Hakkoda site with 19 land cover and plant community types; with average performance of 91% across all sites. In addition, the resulting maps demonstrated a clear distribution of plant community types involved in all sites, highlighting the potential of Sentinel-2 multi-spectral and multi-temporal images with GPE classification system for operational and broad-scale mapping of land cover and plant communities.

The forest transition – or forest-area transition – has been put forward as a land-use concept by A.S. Mather in 1992 (The forest transition. Area 24, 367-379), to describe the historical trend generally observed in the forest area of developed countries, embodied in a V-shaped curve of the forest area over time, and that may serve as a paradigm to understand and anticipate deforestation in the developing world. Well in line with a geographical approach to forests, forest transition has thus been defined as one-dimensional, forest area being the reference state variable. From a forestry perspective, the analysis appears to be reductive, as forests are described by many other state variables than area, including forest growing stock, composition in tree species, or stand structure. Whether the drivers of forest transition (population dynamics, economic modes of production and consciousness, as classified by Mather) also impact these other forest state variables in a general way thus comes forth as a logical issue.From a deductive analysis of forest transition drivers, and from forest trends brought to light in Europe, France, and at other places in the world, we here argue that the forest transition concept can be extended to a multi-dimensional space of forest attributes, characterized by typical ideal dynamics. Cumulative impacts onto forests and irreversible losses in forest biodiversity over a forest transition are hence highlighted. Global change, as a parallel consequence of countries’ developing process, further appears as one additional albeit less coupled dimension of forest transition, as it modifies forest productivity and vitality over time. Since forest ecosystem services and forest profitability primarily depend on such attributes, we argue that the extension of the forest transition concept has significance for land-use change and forest protection issues. A prospect on future changes in the forests of developed countries with the European space as a benchmark is finally proposed that leads to extend the temporal significance of forest transition. Though poorly described, returning forests on abandoned agricultural lands are significant, and deserve greater attention.

Multiple social and environmental justice concerns are linked to urban form such as the distribution of socioeconomic class populations, healthcare spending, air pollution exposure, and human mobility. This study used 1m resolved LIDAR data to characterize land use in Salt Lake County, Utah and associate it with sociodemographic and air quality data at the census block group and zip code levels. We found that increasing tree cover was associated with higher per capita income and lower minority populations while increasing built cover was linked to lower per capita income and higher minority populations. Air quality showed less strong correlations, however, decreased non irrigated cover, increased built cover, and higher amounts of households living under poverty was related to higher long-term PM2.5 exposure. Several policy efforts have been undertaken to improve air quality and reduce negative health outcomes in Utah which are being informed by regulatory and research grade air quality sensors.

Farm activities continued sand winning operations and the allocation of plots of land to prospective developers in Ghana pose a serious threat to the forest covers and lifespan of the Forest and game reserves. With all the positive add ups to the country from forests, Ghana has lost more than 33.7%(equivalent to 2,500,000 hectares) of its forest, since the early 1990s between 2005 and 2010, the rate of deforestation in Ghana was estimated at 2.19% per annum; the sixth highest deforestation rate globally for that period. This shows how important forest monitoring can be to the forestry commission in Ghana. Despite the frameworks which have been developed to help Ghana to protect and restore its forest resources, inadequate monitoring systems remain a barrier to effective implementation. In this study, Google earth engine was used to map and analyze the structural changes of forest cover using JavaScript to query and compute Landsat, MODIS and NOAA AVHRR satellite imageries of the study area (Ghana) with spatial resolutions 30m, 250m and 7km respectively. A supervised classification was performed on three multi-temporal satellite imageries and a total of six major land use and land cover classes were identified and mapped. By using random Forest-classification technique, from 1985 to 2018 recorded by NOAA AVHRR, forest cover has decreased by 66% and 2000 to 2018 recorded by Landsat and MODIS 61% and 47% respectively. A decrease in the forest has been as a result of anthropogenic activities in Ghana. A change detection analysis was performed on these images and it was noted that Ghana is losing forest reserves in every 5years. Overlay of the reserved forest of the 2000 and the classified map of 2018 shows vegetation changed during 2000-2018 remarkably. Therefore, forest-related institutions like the Forestry Commission can employ and use this monitoring system on Google Earth Engine for processing satellite images particularly Landsat, MODIS and NOAA AVHRR for forest cover monitoring and analysis for fast, efficient and reliable results.

Strip-mined land (SML) disturbed by coal-mining is the non-crop land resource that can be utilized to cultivate high-yielding energy crops such as miscanthus for bioenergy applications. However, the biomass yield potential, annual availability and environmental impacts on growing energy crops in SML are less understood. In this study, we estimated the yield potential of miscanthus (Miscanthus sinensis) in SML and its environmental impacts on local streams using the Soil and Water Assessment Tool (SWAT). After calibration and validation of the SWAT model, the results demonstrated that miscanthus yield potentials were 2.6 (0.8−5.53), 10.0 (1.3−16.0) and 16.0 (1.34−26.0) Mg ha^-1 with the fertilizer application rate of 0, 100, and 200 kg-N ha^-1 respectively. Furthermore, cultivation of miscanthus in the SML has the potential to reduce sediment (~20%) and nitrate (2.5%−10.0 %) loads reaching to water streams with a marginal increase in phosphorus load. The available SML in the United States could produce about 10 to 16 dry Tg of biomass per year without negatively impacting the water quality. In conclusion, SML can provide a unique opportunity to produce biomass for bioenergy applications, while improving stream water quality in highly dense mining area (the Appalachian region) in the United States.

The heavy demand of water resources from the Zarqa River Basin (ZRB) has resulted in a base-flow reduction of the River from 5m³/s to less than 1m³/s. This paper aims at predicting Curve Numbers (CN) as a baseline scenario and proposing restoration scenarios for ZRB. The method includes classifying the soil type and land use, predicting CNs, and proposing CN restoration scenarios. Prediction of existing CNs will be in parallel with the runoff prediction using the US Army Corps of Engineers HEC-1 Model, and Rainfall-Runoff Model (RRM). The models have been set up at the land use distribution of 0.3% water body, 9.3% forest and orchard, 71% mixture of grass, weeds, and desert shrubs, 7.0% crops, 4.0% urban areas, and 8.4% bare soil. The results show that CN under dry condition are 59, 78 under a normal condition and 89 under a wet condition. During vegetation period, CN are 52, 72 and 86 for the dry, normal and wet condition respectively. The restoration scenarios; CN decreases runoff, and increases soil moisture when using the contours, terraces and crop residues. Analyzing results of CN scenarios will be a fundamental tool to support end-users related to their targets to achieve watershed restoration.

Mining for resources extraction may lead to several geological and associated environmental changes due to ground movements, collision with mining cavities and deformation of aquifers. Geological changes may continue in a reclaimed mine area, and the deformed aquifers may entail a breakdown of substrates and an increase in ground water tables, which may cause surface area inundation. Consequently, a reclaimed mine area may experience surface area collapse, i.e. subsidence, and degradation of vegetation health. Thus, monitoring short-term landscape dynamics in a reclaimed mine area may provide important information on the long-term geological and environmental impacts of mining activities. We studied landscape dynamics in Kirchheller Heide, Germany, which experienced extensive soil movement due to longwall mining without stowing, using Landsat imageries between 2013 and 2016. A Random Forest image classification technique was applied to analyse land-use and land-cover dynamics and the growth of wetland areas was assessed using a Spectral Mixture Analysis (SMA). We also analyzed the changes in vegetation health using a Normalized Difference Vegetation Index (NDVI). We observed a 19.9% growth of wetland area within the four years with 87.2% of growth in the coverage of two major waterbodies in the reclaimed mine area. NDVI values indicate that 66.5% of the vegetation of the study area was degraded due to changes in ground water tables and surface flooding. Our results inform environmental management and mining reclamation authorities about the subsidence spots and priority mitigation areas from land surface and vegetation degradation in Kirchheller Heide.

There is increasing demand from stakeholders for tools to support outcome-based approaches in environmental management. For such tools to be useful, understanding user requirements is key. In Scotland, UK, stakeholders were engaged in the development of an Environmental Decision Support System (EDSS) to support the management of land and freshwater resources for multiple policy outcomes. A structured participatory engagement process was employed to determine stakeholder requirements, establish development principles to fulfil these requirements and road-test prototypes. The EDSS specification that emerged from this bottom-up process was spatially-explicit, free at the point of use, and touch and mobile device compatible. This application, which is under development, does not closely resemble most existing published EDSS. We suggest that there is a mismatch between the way scientists typically conceptualise EDSS and the kinds of applications that are likely to be useful to decision-makers on the ground. Interactive mobile and web-based geospatial information services have become ubiquitous in our daily lives, but their importance is not reflected in current literature on EDSS. The current focus in environmental management on adaptive, stakeholder-centred strategies based on outcomes offers an opportunity to make better use of these new technologies to aid decision-making processes.

The key to simulating soil erosion is to calculate the vegetation cover (C) factor. Methods that apply remote sensing to calculate C factor at regional scale cannot directly use the C factor formula. That is because the C factor formula is obtained by experiment, and needs the coverage ratio data of croplands, woodlands and grasslands at standard plot scale. In this paper, we present a C factor conversion method from a standard plot to a km-sized grid based on large sample theory and multi-scale remote sensing. Results show that: 1) Compared with the existing C factor formula, our method is based on the coverage ratio of croplands, woodlands and grasslands on a km-sized grid, takes the C factor formula obtained from the standard plot experiment and applies it to regional scale. This method improves the applicability of the C factor formula, and can satisfy the need to simulate soil erosion in large areas. 2) The vegetation coverage obtained by remote sensing interpretation is significantly consistent (paired samples t-test, t = −0.03, df = 0.12, 2-tail significance p < 0.05) and significantly correlated with the measured vegetation coverage. 3) The C factor of the study area is smaller in the middle, southern and northern regions, and larger in the eastern and western regions. The main reason for that is the distribution of woodlands, the Hunshandake and Horqin sandy lands and the valleys affected by human activities. 4) The method presented in this paper is more meticulous than the C factor method based on the vegetation index, improves the applicability of the C factor formula, and can be used to simulate soil erosion on large scale and provide strong support for regional soil and water conservation planning.

Surface waves generated by Extra-Tropical Cyclones (ETCs) can significantly affect shipping, fishing, offshore oil and gas production and other marine activities. This paper presents results of satellite-data-based investigation of wind waves generated by two North Atlantic ETCs. These ETCs were fast-moving systems, inhibiting resonance (synchronism) between the group velocity of the generated waves and the ETC translation velocity. For these cases, the wave generation begins when the front-boundary of the storm appears at a given ocean location point. Since developing waves are slow, they move backward relative to the storm, grow in time, and then leave the ETC stormy area through the rear sector. Multi-satellite observations confirm such a paradigm, and reveal that the storm regions is filled up with young developing wind waves which are most developed in the rear-right sector. As observed, the energy of these waves was growing in time during the ETC life span. It is demonstrated that the extended-fetch concept (inherent for Tropical Cyclones) does not apply for ETC. Instead, by analogy, the concept of extended-duration wave growth concept is more relevant. Satellite observations well confirm the validity of duration-laws for waves generated by ETCs, and demonstrate that extended-fetch regime for observing waves can only asymptotically be achieved, - at time intervals exceeding the lifespan of considered ETCs.

The most common long-term complication of silicone breast implants (SMI) remains capsular fibrosis. The etiology of this exaggerated implant encapsulation is multifactorial but primarily induced by the host response towards the foreign material silicone. Identified risk factors included specific implant topographies. Of note, breast implant-associated anaplastic large cell lymphoma (BIA-ALCL), has only been observed in response to textured surface implants. We hypothesize that reduction of SMI surface roughness causes less host response hence better cosmetic outcome with fewer complications for the patient. A total of 7 patients received the routinely used CPX®4 breast expander (~60 µM Ra) and the novel SmoothSilk® (~ 4 µM Ra), fixed prepectoral with a titanised mesh pocket and randomized to the left or right breast after bilateral prophylactic NSME (nipple-sparing mastectomy). We aimed to compare the postoperative outcome regarding capsule thickness, seroma formation, rippling, implant dislocation as well as comfortability and practicability. Our analysis shows that surface roughness is an influential parameter in controlling fibrotic implant encapsulation. First time intra-individually compared in patients, our data confirm an improved biocompatibility with minor capsule formation around SmoothSilk® implants with an average shell roughness of 4 µM and in addition an amplification of host response by titanised implant pockets.

The goal of farmers operating in a market economy is to maximise profit. In the face of the changing political situation, the main social interest, besides food security, should be energy security. This article aims to indicate the direction of agricultural policy development so that it guarantees both the economic security of producers—farmers—and Europe’s energy security. The work uses data obtained from the agri benchmark Cash Crop database. DEA method and stepwise multiple regression were used. The research showed that plants are already grown in Europe which will ensure high energy efficiency of production without compromising farm financial results (including oats, peas and winter rye) and that improving the involvement of certain inputs results in improved production efficiency (among others, by expenditure on agricultural advisory services). The significance of the presented research results from the fact that the recent COVID pandemic and escalation of the military conflict in Ukraine have led to a renewed interest in the concept of EU energy security, i.e. generation of generating the greatest possible amount of energy within the EU, to be used both for food and non-food purposes.

An investigation studied the impact of various solid waste types on Helianthus plant growth, encompassing both Helianthus annuus and Helianthus giant. Common sunflowers (Helianthus) were cultivated to assess the influence of soil substrates with differing compositions and solid waste concentrations on plant growth and morphology. Materials included fireplace ash, oil burner dust, forge dust, land of Milos (pozzolan), and land of Milos mixed with olive core. The aim was to determine if Helianthus could remediate soil contaminated by these wastes. Results re-vealed plant growth relied on substrate quality and quantity. High concentrations of fireplace ash and oil burner dust were detrimental, while forge dust, land of Milos, and olive core combinations supported satisfactory growth and improved resistance. Generally, Helianthus annuus outper-formed Helianthus giant. These findings highlight Helianthus' potential for soil restoration and decontamination under specific substrate conditions concerning solid waste type and concentration.

The composition and pattern of ecosystems are important factors determining the overall status and spatial differences of ecosystem service functions. However, under the background of differential land policies and ecological protection policies, research on the trend of ecological system pattern changes in the Fenhe River Basin is insufficient. Taking the upper and middle reaches of the Fenhe River Basin as the study area, based on long-term NDVI index and multi-period LUCC remote sensing images, this study used spatial statistics and time trend analysis methods to analyze the spatio-temporal dynamic changes of vegetation, land use, landscape pattern, and explored the impact of major driving factors on ecosystem changes. The results show that: (1) From 2010 to 2020, the vegetation cover in the upper and middle reaches of the Fenhe River Basin increased, with an annual NDVI increment of 0.003 (P<0.001). NDVI showed an increasing trend spatially, with significant statistics (P<0.001) and significant changes (P<0.05) in vegetation in high-altitude mountain areas, and the vegetation cover was mostly forests or grasslands. There was no significant change in vegetation cover in the low-lying urban agglomeration area. (2) From 2010 to 2020, the area of water bodies or wetlands in the study area significantly decreased, with 51.3% converted to arable land and 33.9% transferred to construction land, while only 2.2% remained as water bodies or wetlands. From 2015 to 2020, the trend of water body changes slowed down, with the proportions of conversion to arable land and construction land being 44.0% and 18.4% respectively, while the area of wetlands or water bodies remained at 16.3%. During the period of 2015-2020, the area of water bodies or wetlands converted to other land types increased by more than 14% compared to 2010-2015. This proportion reached more than 30% compared to the 13th Five-year Plan Period. (3) From 2010 to 2020, the spatial changes of landscape diversity (SHDI) and evenness (SHEI) of LUCC showed heterogeneous characteristics. In the high-altitude areas near the river basin boundary, the values of SHDI and SHEI were below 1.0. While in the low-altitude plain areas and urban areas with relatively frequent human activities, the values of SHDI and SHEI were above 1.0, and the values in urban areas could reach above 1.5. The evolution of ecosystem patterns in the upper and middle reaches of the Fenhe River Basin in the past decade has been clarified, providing a scientific basis for the construction and management of ecological environment governance and restoration projects in the Fenhe River Basin, and providing practical references for ecological protection and high-quality development practice in the Yellow River Basin.

Fit-for-purpose land administration (FFPLA) seeks to simplify cadastral mapping via lowering the costs and time associated with conventional surveying methods. The approach can be applied to both initial establishment and on-going maintenance of system. In Ethiopia, cadastral maintenance remains an on-going challenge, especially in rapidly urbanizing peri-urban areas, where farmers' land rights and tenure security are often jeopardized. Automatic Feature Extraction (AFE) is an emerging FFPLA approach, proposed as an alternative for mapping and updating cadastral boundaries. This study explores the role of the AFE approach for updating cadastral boundaries in the vibrant peri-urban areas of Addis Ababa. Open-source software solutions are utilized to assess the (semi-) automatic extraction of cadastral boundaries from orthophotos (segmentation), designation of 'boundary' and 'non-boundary' outlines (classification), and delimitation of cadastral boundaries (interactive delineation). Both qualitative and quantitative assessments of the achieved results (validation) are undertaken. A high-resolution orthophoto of the study area and a reference cadastral boundary shape file are used, respectively, for extracting the parcel boundaries and validating the interactive delineation results. Qualitative (visual) assessment verified the completed extraction of newly constructed cadastral boundaries in the study area, although non-boundary outlines such as footpaths and artefacts are also retrieved. For the buffer overlay analysis, the interactively delineated boundary lines and the reference cadastre were buffered within the spatial accuracy limits for urban and rural cadasters. As a result, the quantitative assessment delivered 52% correctness and 32% completeness for a buffer width of 0.4m and 0.6m, respectively, for the interactively delineated and reference boundaries. The study further demonstrated the potentially significant role AFE could assist in delivering fast, affordable, and reliable cadastral mapping. Further investigation, based on user input and expertise evaluation, could help to improve the approach and apply it to a real-world setting.

Fire regimes in mountain landscapes of southern Europe have been shifting from their baselines due to rural abandonment and fire exclusion policies. Understanding the effects of fire on biodiversity is paramount to implement adequate management. Herein, we evaluated the relative role of burn severity and heterogeneity on bird abundance in an abandoned mountain range located in the biogeographic transition between the Eurosiberian and Mediterranean region (the Natural Park ‘Baixa Limia–Serra do Xurés’). We surveyed the bird community in 206 census plots distributed across the Natural Park, both inside and outside areas affected by wildfires over the last 11 years (from 2010 to 2020). We used satellite images of Sentinel 2 and Landsat missions to quantify the burn severity and heterogeneity of each fire within each surveyed plot. We also accounted for the past land use (forestry or agropastoral use) by using a land cover information for year 2010 derived from satellite image classification. We recorded 1,735 contacts from 28 bird species. Our models, fitted by using GLMs with Poisson error distribution (pseudo-R²_-average of 0.22 ± 0.13), showed that up to 71% of the modelled species were linearly correlated with at least one attribute of the fire regime. The spatiotemporal variation in burnt area and severity were relevant factors for explaining the local abundance of our target species (39% of the species; Akaike weights > 0.75). We also found a quadratic effect of at least one fire regime attribute on bird abundance for 60% of the modeled species. The past land use, and its legacy after 10 years, was critical to understand the role of fire (Akaike weights > 0.75). Our findings confirm the importance of incorporating remotely sensed indicators of burn severity into the toolkit of decision makers to accurately anticipate the response of birds to fire management.

Integrated landscape approaches (ILA) aim to reconcile multiple, often competing, interests across agriculture, nature conservation, and other land uses. Recognized ILA design principles provide guidance for their implementation, yet application remains challenging, and a strong performance evidence-base is yet to be formed. A comprehensive literature review and focus group discussions with practitioners identified considerable diversity of ILA in actors, temporal, and spatial scales, inter alia. This diversity hampers learning from and steering these integrated planning approaches because of its intractable nature. Therefore, we developed a tool—an ‘ILA mixing board’—to structure the complexity of ILA into selectable and scalable attributes in a replicable way to allow planning, diagnostics, and comparative assessment of ILA. The ILA mixing board tool presents seven qualifiers, each representing a key attribute of ILA design and performance such as project flexibility, inclusiveness of the dialogue, and the centrality of the power distribution. Each qualifier has five (non-normative) outcome indicators that can be registered as present or absent. This process in turn guides planners, evaluators and other participating stakeholders involved in landscape management to diagnose the ILA type, and or its performance. We apply the ILA mixing board as a diagnostic tool to three ILA cases in Nicaragua, Madagascar, and the Congo Basin to show some of the many possible configurations of qualifiers on the mixing board. Overall, the tool allows comparative analyses of the complexity of ILA in a structured and manageable way.

The article describes the results of comparison of occurence of buildings (and address points) in Poland with delimitations of land use belonging to particular classes in the CORINE Land Cover (CLC) 2018 dataset. Large discrepancies have been identified, which reach on average approx. 34% of addresses and 35% of buildings located outside class 1 (artificial surfaces), mainly on terrains of class 2 (agricultural areas). Among single-family buildings it was 37% and among new addresses (forecasted or ‘under construction’ buildings) – as much as 50%. This puts a question mark over the possibility of using CLC data with resolution of 25 ha for monitoring of spatial planning and development in Poland for purposes of the diagnosis and assessment of the scale of dispersion of built-up areas. It is worth carrying out similar analyses in other countries, known for the deconcentration processes and a relatively large share of dispersed settlement e.g. other CEE countries, Spain, Portugal, Italy.

In the Brazilian Amazon, rural settlements are increasingly isolated by large-scale production farms, jeopardizing their sustainability and the good living of family farmers. Works were carried out in settlements to measure sustainability. However, the majority does not consider the participation and the collectively of those involved. In this way, we propose to evaluate, in a collective and participatory way, the sustainability and good living of the SDP São Paulo Rural Settlement, of the northern Amazon of Mato Grosso. We used the didactic-pedagogical method Circle of Sustainability, developed from five points: 1st - circle of investigation of generating themes; 2nd - circle of the history of the subject world; 3rd - circle of diagnosis of rural settlements; 4th - circle of exchange of knowledge; and 5th - circle of sustainable perceptions and narratives. The historical, socioeconomic and cultural characterization of the settlement allowed us to understand how sustainability and good living are being built in the settlement history process. Sustainability and good living are dialectical processes, are under construction, in movement.

The aim of this study is to evaluate three different strategies to improve classification accuracy in a highly fragmented semiarid area. i) Using different classification algorithms: Maximum Likelihood, Random Forest, Support Vector Machines and Sequential Maximum a Posteriori, with parameter optimisation in the second and third cases; ii) using different feature sets: spectral features, spectral and textural features, and spectral, textural and terrain features; and iii) using different image-sets: winter, spring, summer, autumn, winter+summer, winter+ spring+summer; and a four seasons combination. A 3-way ANOVA is used to discern which of these approaches and their interactions significantly increases accuracy. Tukey-Kramer contrast using a heteroscedasticity-consistent estimation of the kappa covariances matrix was used to check for significant differences in accuracy. The experiment was carried out with Landsat TM, ETM, and OLI images corresponding to the period 2000-2015. A combination of four images was the best way to improve accuracy. Maximum Likelihood, Random Forest and Support Vector Machines do not significantly increase accuracy when textural information is added, but do so when terrain features are taken into account. On the other hand, Sequential Maximum a Posteriori increases accuracy when textural features are used, but reduces accuracy substantially when terrain features are included. Random Forest using the three feature subsets and Sequential Maximum a Posteriori with spectral and textural features had the largest kappa values, around 0.9.

The electronic properties of calcium intercalated graphite (CaC6) as a function of pressure are revisited using density functional theory (DFT). The electronic band structures of CaC6, like many other layered superconducting materials, display cosine-shaped bands at or near the Fermi level (FL). Such bands encompass bonding/antibonding information with a strong connection to superconducting properties. Using an hexagonal cell representation for CaC6, construction of a double supercell in the c-direction effects six-folding in reciprocal space of the full cosine function, explicitly revealing the bonding/antibonding relationship divide at the cosine midpoint. Similarly, folding of the Fermi surface (FS) reveals physical phenomena relevant to electronic topological transitions (ETT) with application of pressure. For CaC6, the peak value for the superconducting transition temperature, Tc, occurs at about 7.5 GPa, near to the observed pressure of the calculated ETT. At this pressure, the radius of the nearly spherical Ca 4s-orbital FS coincides with three times the distance from the G centre point to the Brillouin zone (BZ) boundary of the 2c supercell (which is equal to half the identically defined distance for the primitive rhombohedral BZ). In addition, the ETT coincides with alignment of the non-bonding (inflection) point of the cosine band (the point at which the sign of the cosine amplitude modulation is reversed) with the FL. At other calculated pressure conditions, the Ca 4s-orbital FS undergoes topological changes that correspond and can be correlated to experimentally determined changes in Tc. The ETT is a key mechanism that circumscribes the known significant drop in Tc for CaC6 as a function of increasing pressure.

In this study, a new diphosphate compound, Ag0.2Na0.6FeP2O7, was synthesized using a solid-state reaction method and extensively studied using various techniques. The compound's structure was confirmed through X-ray diffraction analysis, revealing a single-phase monoclinic structure with the P21/C space group. The electrical behavior of the compound was investigated, and its conductivity followed Jonscher's universal law. The correlated barrier hopping (CBH) model explained the temperature-dependent ac conductivity and parameter "s" well. The study also explored the contribution of single-polaron and bipolaron hopping to the a.c. conductivity and discussed the ionic conductivity in relation to the structural characteristics of the sample. Overall, this investigation significantly enhances our comprehension of the distinctive electrical properties of Ag0.2Na0.6FeP2O7 and its potential practical applications.

To elucidate mesenchymal stromal cells (MSC)-tumor intricate and ambiguous interactions, the reliable cell labeling and tracking techniques are imperative. Traditional methods of cell labelling have limitations mostly relevant to need for genetic modification what demands the exploration for alternative strategies. Here, we propose using fluorescent photoconvertible microcapsules containing Rhodamine B (RhB) to study mMSC migration in brain tumors. These 3 μm sized microcapsules are readily internalised by cells and undergo photoconversion under 561 nm laser exposure with fluorescence blue shift on demand. Optimal photoconversion was achieved with a laser irradiation duration of 0.4 ms, which provide a maximal brightness of photoconverted label without an excessive laser exposure on cells. Capsules modified with polyallylamine hydrochloride demonstrated the best potential for intracellular uptake without significantly affecting cell viability, motility, or proliferation. The optimal ratio of 20 capsules per mMSC was determined for labeling. Moreover, migration of individual mMSCs within 2D and 3D glioblastoma cell (EPNT-5) colonies over 2 days and in vivo tumor settings over 7 days was tracked. Our study unveils a robust platform for investigating MSC-tumor dynamics, offering insights into therapeutic strategies. Photoconvertible microcapsules could also become an indispensable tool for studying complex fundamental processes of cell-cell interactions for a wide range of problems in biology and medicine.

Efficient utilization of biomass requires conversion into forms that can be optimally applied in energy generation. Briquetting involves compaction of biomass into solid blocks that are more efficient than raw biomass and provides for ease of transport and handling. These are improved when the briquettes possess high shatter index and compressive strength. Due to difference in nature and composition, it is imperative to define optimum conditions for the production of quality and durable briquettes for individual biomass compacted into briquettes. This study studied the effects of process variables on the strength and durability of biomass briquettes produced using Abura sawdust. The lateral compressive strength and drop shatter index were investigated whilst varying the temperature (100-150 °C), pressure (9-15 MPa) and hold time (15-30 min). The compressive strength ranged between 2.06 and 5.15 MPa whilst the shatter index was between 50 and 600. The pressure was significant to the determination of the compressive strength (p &lt; 0.1) and the shatter index (p &lt; 0.05). Mechanical characteristics of the binderless Abura sawdust briquettes can be improved by optimizing the densification variables during the briquetting process when moderate pressures are used for compaction.