The inhibition of localised corrosion is known to involve multiple processes taking place over a range of time and length scales that are difficult to study by conventional electrochemical methods. This work demonstrates an approach to probing complex localised electrochemical processes by combining an electrochemically integrated multi-electrode array (also known as wire beam electrode (WBE)), scanning vibrating electrode technique, scanning electrochemical microscopy and surface analytical techniques. Each technique reveals certain aspects of the dynamically changing, multi-scale, inhibitor-microstructure interactions and local chemistry over a heterogeneous AA2024-T3 alloy surface in the presence of an environmentally friendly inhibitor; cerium diphenyl phosphate (Ce(dpp)3).

This paper presents a demonstration of a linearly-polarized transmit-arrays antenna with high-efficiency and wideband operating in X-band. The topology of the unit cell consists of two identical patch antennas loaded by C-loop slot and interconnected by a metalized via through a ground plane sandwiched between two identical substrates [18]. A waveguide measurement system WGMS has been used for single cell characterization (reflection/transmission coefficients). Good results have been demonstrated in terms of matching performances; the reflection coefficient S11 is under 10-dB in the 9.4-10.4 GHz band (i.e. 10.1% around 9.9 GHz) and with only 0.35 dB-insertion loss at 10 GHz. The transmit-arrays prototype permitted to achieve 22.4 dBi of directivity and 20.1 dBi of gain. The aperture and radiation efficiencies are about 28.2% and 58.3%, respectively. With a focal ratio (F/D) of 1/2 the spill-over loss is less than 2 dB. Beam-scanning up to ± 35° has been achieved with the same phase quantization (passive) and less than 3 dB of gain losses.

Managing sidelobe levels (SLLs) in metasurface-driven beam-steering antennas poses a significant challenge due to intrinsic factors leading to grating lobes. Our proposed method employs an equivalent model to optimize large periodic metasurfaces efficiently. This model predicts complete metasurface performance, accounting for mutual coupling between patches. We introduce an evolutionary optimization algorithm based on the Cross Entropy (CE) method to enhance PGM-based beam-steering antennas and suppress sidelobes. Two strategies were employed: first is to optimize the patch dimensions for a sidelobe-free pattern and the second is to maintain the PGM dimensions while optimizing feed array amplitudes. Both strategies effectively suppressed sidelobes, offering insights into the CE method's applicability and effectiveness for CPU-intensive electromagnetic optimization challenges. The proposed CE method variant retains its simplicity while improving monitoring capabilities, addressing this limitation. Smaller generations yield better improvements per evaluation

The paper presents a modified finite element method for nonlinear analysis of 2D beam structures. To take into account the influence of the shear flexibility, a Timoshenko beam element was adopted. The algorithm proposed enables using complex material laws without the need of implementing advanced constitutive models in finite element routines. The method is easy to implement in commonly available CAE software for linear analysis of beam structures. It allows to extend the functionality of these programs with material nonlinearities. By using the structure deformations, computed from the nodal displacements, and the presented here generalized nonlinear constitutive law, it is possible to iteratively reduce the bending, tensile and shear stiffnesses of the structures. By applying a beam model with a multi layered cross-section and generalized stresses and strains to obtain a representative constitutive law, it is easy to model not only the complex multi-material cross-sections, but also the advanced nonlinear constitutive laws (e.g. material softening in tension). The proposed method was implemented in the MATLAB environment, its performance was shown on the several numerical examples. The cross-sections such us a steel I-beam and a steel I-beam with a concrete encasement for different slenderness ratios were considered here. To verify the accuracy of the computations, all results are compared with the ones received from a commercial CAE software. The comparison reveals a good correlation between the reference model and the method proposed.

Beam dumps are indispensable components for particle accelerator facilities to absorb or dispose beam kinetic energy in a safe way. However, the design of beam dumps based on conventional technology, i.e. the energy deposition via beam-dense matter interaction, makes the beam dump facility complicated and large in size, partly due to nowadays’ high beam intensities and energies achieved. In addition, these high-power beams generate radioactive hazards, which need specific methods to deal with. On the other hand, the EuPRAXIA project can advance the laser-plasma accelerator significantly by achieving 1-5 GeV high quality electron beam in a compact layout. Nevertheless, the beam dump based on conventional technique will still produce radiation hazards and make the overall footprint less compact. Here, we propose to implement a plasma beam dump to absorb the kinetic energy from the EuPRAXIA beam. In doing so, the overall compactness of the EuPRAXIA layout will not be impacted, and the radioactivity generated by the facility can be mitigated. In this paper, results from particle-in-cell (PIC) simulations are presented for plasma beam dumps based on EuPRAXIA beam parameters.

Precise individual tree or sample-based inventories derived from 3D point cloud data of mobile laser scanning can improve our comprehensive understanding of the structure, function, resilience, biodiversity, and ecosystem services of urban forests. This study assessed the performance of a hand-held laser scanning system for the extraction of tree position, diameter at breast height (DBH) and tree height (H) in an urban area. A total of 2083 trees of 13 species from 34 plots were analyzed. The results showed that the registration of tree positions using ground control points (GCPs) demonstrated high accuracy, with errors consistently below 0.4 m, except for a few instances. The extraction accuracy of DBH for all trees and individual species remained consistently high, with a total root mean square error (RMSE) of 2.06 cm (6.89%) and a bias of 0.62 cm (2.07%). Notably, broad-leaved trees outperformed coniferous trees, with RMSE and bias values of 1.86 cm (6%) and 0.76 cm (2.46%) compared to 2.54 cm (9.46%) and 0.23 cm (0.84%). Tree height extraction accuracy varied significantly among different species, with R2 values ranging from 0.65 to 0.92. Generally, both DBH and height were underestimated. Linear mixed effects models (LME) were applied to evaluate factors affecting the performance of HLS with the plot as a random factor. LME analysis revealed that plant type and terrain significantly influenced the accuracy of DBH and H derived from HLS data. Other fixed factors of plot area, tree density and trajectory length didn’t have significance. With a large sample size, we concluded that the HLS demonstrated sufficient accuracy in extracting individual tree parameters in urban forests.

A model for the simulation of ion beam extraction from an electron cyclotron resonance ion source is proposed. It is based on the simple fact that charged particles follow magnetic field lines. Therefore magnetic field lines are used to generate initial conditions for ray-tracing. This model reproduces in simulation experimentally obtained results. The importance of correlations in phase-space caused by the magnetic field is shown in simulation. This model also describes the physics of space-charge and its compensation in the extracted (fast) ion beam by low energy electrons. Simulation provides the possibility to test theoretical assumptions, as well as to optimize technical designs.

The color of a thin copper oxide layer formed on a copper plate was transformed from reddish-brown into blue-purple by irradiation with 5 keV Ar+ ions to a fluence as low as 1 1015 Ar+ cm–2. In the unirradiated copper oxide layer, the copper valence state of Cu2+ as well as Cu+ and/or Cu0 was included as indicated by the presence of a shake-up satellite line in a photoemission spectrum. While for the irradiated one, the satellite line decreased in intensity, indicating that irradiation resulted in the reduction from Cu2+ to Cu+ and/or Cu0. Furthermore, nuclear reaction analysis using a 16O(d, p)17O reaction with 0.85 MeV deuterons revealed a significant loss of oxygen (51015 O atoms cm–2) in the irradiated layer. Thus, the chromatic change observed in the present work originated in the irradiation-induced reduction of a copper oxide.

A cell-surface ectonucleotidase CD39 mediates the conversion of extracellular ATP into immunosuppressive adenosine with another ectonucleotidase CD73. The elevated adenosine in the tumor microenvironment (TME) attenuates antitumor immunity, which promotes tumor cell immunologic escape and progression. Anti-CD39 monoclonal antibodies (mAbs), which suppress the enzymatic activity, can be applied to antitumor therapy. Therefore, an understanding of the relationship between the inhibitory activity and epitope of mAbs is important. We previously established an anti-mouse CD39 (mCD39) mAb, C₃₉Mab-1 using the Cell-Based Immunization and Screening (CBIS) method. In this study, we determined the critical epitope of C₃₉Mab-1 using flow cytometry. We performed the PA tag (12 amino acids)-substituted analysis (named PA scanning) and RIEDL tag (5 amino acids)-substituted analysis (named RIEDL scanning) to determine the critical epitope of C₃₉Mab-1 using flow cytometry. By the combination of PA scanning and RIEDL scanning, we identified the conformational epitope, spanning three segments of 275^th to 279^th, 282^nd to 291^st, and 306^th to 323^rd amino acids of mCD39. These analyses would contribute to the identification of the conformational epitope of membrane proteins.

Self-assembling films typically used for colloidal lithography have been applied to pine wood substrates to change the surface wettability. Therefore, monodisperse polystyrene (PS) spheres have been deposited onto a rough pine wood substrate via dip coating. The resulting PS sphere film resembled a polycrystalline FCC-like structure with typical domain sizes of 5 – 15 single spheres. This self-assembled coating was further functionalized via an O2 plasma. This plasma treatment strongly influenced the particle sizes in the outermost layer, and hydroxyl as well as carbonyl groups were introduced to the PS spheres’ surfaces, thus generating a superhydrophilic behaviour.

We propose versatile integrated polarizers based on geometric metasurfaces. Metasurface polarizer consists of L-shaped hole array etched on a silver film and it can generate simultaneously several polarization states including the linear polarization, circular polarization, elliptical polarization, or even hybrid polarization. Meanwhile, the combination of output polarization states changes with the illumination polarization type. The theoretical analysis provides the detail explanation for the generation of the integrated polarization states. The well-designed metasurface polarizers may generate more complex polarization modes including vector beams and vector vortex beams. The theoretical and simulated results confirm the polarization performance of the proposed integrated metasurface polarizers. The compact design of metasurface polarizers and the controllable generation of versatile polarization combinations are benefit to the applications of polarization light in optical imaging, biomedical sensing and material processing.

Optical beam splitter is used for dividing an input optical beam into several separate beams with specific power ratio. Usually, conventional beam splitters have bulky dimensions and fixed dividing ratio which significantly limit the design of new miniaturized optical devices and integrated optical circuits. We propose and investigate a novel physical concept of a miniaturized planar optical splitter/coupler with a switching element in the form of a photonic molecule (PM) pair dispersing input optical fluxes along multiple ways with variable power proportions. The structural design of the proposed splitter is based on a silicon-on-insulator (SOI) platform and composed of high-quality resonators in the form of electromagnetically coupled submicron-sized microcylinders. The control on the power division ratio and the selection of optical beam directions is realized by tuning the photonic splitter structure to the corresponding resonance of PM supermode. Compared to known analogues, the proposed design is easy to fabricate, suitable for integration into a "System-on-a-chip" platform and can dynamically change the beam power division ratio by input wave-phase manipulation.

Dynamic analyses and seismic assessments of multi-storey buildings at urban level require large-scale simulations and computational procedures based on simplified but accurate numerical models. At this aim the present paper propos-es an equivalent non-uniform beam-like model, suitable for the dynamic analysis of buildings with asymmetric plan and non-uniform vertical distribution of mass and stiffness. The equations of motion of this beam-like model, which pre-sents only shear and torsional deformability, are derived through the application of Hamilton’s principle. The linear dy-namic behaviour is evaluated by discretizing the continuous non-uniform model according to a Rayleigh-Ritz approach based on a suitable number of modal shapes of the uniform shear-torsional beam. In spite of its simplicity, the model is able to reproduce the dynamic behaviour of low- and mid-rise buildings with a significant reduction of the computa-tional burden with respect to that required by more general models. The efficacy of the proposed approach has been tested, by means of comparisons with linear FEM simulations, on three multi-storey buildings characterized by different irregularities. The satisfactory agreement, in terms of natural frequencies, modes of vibration and seismic response, proves the capability of the proposed approach to reproduce the dynamic response of complex spatial multi storey frames.

Gardens play a key role in the definition of the cultural landscape since they reflect the culture, identity and history of a people. They also contribute to the ecological balance of the city. Despite gardens have an historic and social value, they are not protected as much as the rest of the existing heritage, like architecture and archaeological sites. While methods of built-heritage mapping and monitoring are increasing and constantly improving to reduce built-heritage loss and the severe impact of natural disasters, the documentation and survey techniques for gardens are often antiquated, inventories are typically made by non-updated/updatable reports, and rarely they are on digital format and in 3D. This paper presents the preliminary results of a study on latest technology for gardens laser scanning. We compared static Terrestrial Laser Scanning and Mobile Laser Scanning point clouds, to evaluate their quality for documentation and the estimation of the tree attributes. The evaluation is based on visual observation and graphic comparison of the two point clouds acquired in different instances. Both methods produced useful outcomes for the research scope within their limitations. Terrestrial Laser Scanning is still the method that offers more accurate point clouds with a higher point density and less noise level. However, the more recent Mobile Laser Scanning is able to survey in less time, significantly reducing the costs for site activities, data post-production and registration. Both methods have their own restrictions that are amplified by site features, mainly the lack of plans for the geometric alignment of scans and for the Simultaneous Location and Mapping (SLAM) process. We also offer the results of a comparison of the functional range of the two machines, as well as for a comparison of their terrain information extraction capabilities.

Machine Learning deals with creating algorithms capable of learning from the provided data. These systems have a wide range of applications and can also be a valuable tool for scientific research which in recent years has been focused on finding new diagnostic techniques for particle accelerator beams. In this context SPARC_LAB is positioned, a facility located at the Frascati National Laboratories of INFN, where the progress of beam diagnostics is one of the main developments of the entire project. With this in mind, you aim to present the design of two neural networks aimed at predicting the spot size of the electron beam of the plasma-based accelerator at SPARC_LAB, which powers an undulator for the generation of x-ray Free Electron Laser (XFEL). Data-driven algorithms use two different data preprocessing techniques, namely autoencoder neural network and PCA. With both approaches, the predicted measurements can be obtained with an acceptable margin of error and most importantly without activating the accelerator, thus saving time, even compared to a simulator that can produce the same result but much more slowly. The goal is to lay the groundwork for creating a digital twin of linac and conducting virtualized diagnostics using an innovative approach.

This paper presents a multifunctional reflective digital metasurface of arbitrary base based on voltage tunable liquid crystal (LC). The reflective digital metamaterial can be multiplexed for different desirable functions by properly biasing the LC for different code patterns. Simulation results of three significant functions, beam steering with a steering elevation angle 27° at 75 GHz, RCS reduction of at least 15dB along the incident direction, and beam shaping with different beam shapes have been presented to prove the concept.

Owing to the nondiffracting, self-accelerating, and self-healing properties, Airy beams of different nature have become a subject of immense interest in the past decade. Their interesting properties have opened doors to many diverse applications. Consequently, the questions of how to properly design spatial manipulation of Airy beams or how to implement them in different setups have become important and timely in the development of various optical devices. Here, based on our previous work, we present a short review on the spatial control of Airy beams, including the interactions of Airy beams in nonlinear media, beam propagation in harmonic potential, and the dynamics of abruptly autofocusing Airy beams in the presence of a dynamic linear potential. We demonstrate that under the guidance of nonlinearity and external potential, the trajectory, acceleration, structure, and even the basic properties of Airy beams can be adjusted to suit specific needs. We describe other fascinating phenomena observed with Airy beams, such as self-Fourier transformation, periodic inversion of Airy beams, and the appearance of spatial solitons in the presence of nonlinearity. These results have promoted the development of Airy beams, and have been utilized in various applications, including particle manipulation, self-trapping, and electronic matter waves.

Marine renewable energy is emerging as one of the fast-growing industry in the last decades, as modern society pushes for technologies that can convert energy contained from winds, waves, tides and stream flows. The implementation of renewable energy technologies impose high demands on both structural and environmental engineering, as the energy converters have to work under extreme conditions where parameters such as sea-bottom configuration, water transparency and depth, sea-states and prevailing winds are harsh. Constant monitoring of the marine environment is crucial in order to keep this sector reliable. Active acoustics is becoming a standard tool to collect multi-dimensional data from physical, geological and biological properties of the marine environment. The Div. of Electricity of Uppsala University have been developing an environmental monitoring platform based on sonar (Sound Navigation And Raging) systems. This platform aims to monitor the installation, operation and decommissioning of marine renewable energy converters. The focus will be given the observations of behaviours of marine animals in vicinity of energy converters but also structural inspection and monitoring of MRETs. This paper describes how this multifunctional environmental monitoring platform come to existence from the design to the deployment phase.

The purpose of the investigation was to determine the relationship between rotary kiln liner loss and steel structure ovality. As measurement apparatus, a terrestrial laser scanner was used. The interior and exterior of the rotary kiln were measured. The primary focus object was inner-lining loss and the geometric characteristics of cylindrical shells. The research uncovered significant disparities in inner lining loss between sections. A correlation was found between ovality and elimination of inner lining. Due to the hypothesis of constant inner linig loss from the middle of the rotary kiln, the investigation found that the loss of brick lining was less than the value reported from the boreholes. The study offers significant information on maintenance and repair strategies for rotary kilns, which have the potential to increase their efficiency and useful life.

The segmentation of urban scene mobile laser scanning (MLS) data into meaningful street objects is a great challenge due to the scene complexity of street environments, especially in the vicinity of street objects such as poles and trees. This paper proposes a three-stage method for the segmentation of urban MLS data at the object level. The original unorganized point cloud is first voxelized, and all information needed is stored in the voxels. These voxels are then classified as ground and non-ground voxels. In the second stage, the whole scene is segmented into clusters by applying a density-based clustering method based on two key parameters: local density and minimum distance. In the third stage, a merging step and a re-assignment processing step are applied to address the over-segmentation problem and noise points, respectively. We tested the effectiveness of the proposed methods on two urban MLS datasets. The overall accuracies of the segmentation results for the two test sites are 98.3% and 97%, thereby validating the effectiveness of the proposed method.

Fracture analysis of reinforced concrete deep beam strengthened with carbon fiber-reinforced polymer (CFRP) plates was carried out. The present research aims to find out whether the crack propagation in a strengthened deep beam follows linear elastic fracture mechanics (LEFM) theory or nonlinear fracture mechanics theory. To do so, a new energy release rate based on nonlinear fracture mechanics theory was formulated on the finite element method and the discrete cohesive zone model (DCZM) was developed in deep beams. To validate and compare with numerical models, three deep beams with rectangular cross-sections were tested. The code results based on nonlinear fracture mechanics models were compared with experimental results and ABAQUS results carried out based on LEFM. The predicted values of initial stiffness, yielding point and failure load, energy absorption, and compressive strain in the concrete obtained by the proposed model were very close to the experimental results. However, the ABAQUS software results have greater differences with the experimental results. For example, the predicted failure load for the shear-strengthened deep beam using the proposed model has only 6.3% differences compared to the experimental result. However, the predicted failure load using ABAQUS software based on LEFM has greater differences (25.1%) compared to the experimental result.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p < 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

Bone cement, mainly based in PMMA, is commonly used in different arthroplasty surgical proce-dures, and its use is essential for prosthesis fixation. However, its manufacturing process reaches high temperatures that can produce necrosis in the patients' surrounding tissues. In order to con-tribute to avoid this problem, the addition of graphene could delay the polymerisation of the MMA and, simultaneously, contribute to the optimisation of the composite material's properties. This article analysed the effect of the addition of different percentages of Highly Reduced Graphene Oxide (HRGO) with different wt. % (0,10, 0,50 and 1,00) and surface densities (150, 300, 500 and 750 m2/g) on the physical, mechanical, and thermal properties of commercial PMMA-based bone cement and its processing. It was noticed that a lower sintering temperature would be reached with this addition, making it less harmful to use in surgery and as it reduces its adverse effects. In contrast, the materials' density does not show significant changes, which indicates that the addi-tion of HRGO does not significantly increase its porosity. Lastly, the mechanical properties are re-duced by almost 20 %. Nevertheless, these properties are high enough so that these new materials can still fulfil their structural function.

Engineering application of additively manufactured (AM) metallic materials is quite limited by their fatigue behaviors which are very inconsistent with that of conventionally wrought or cast ones. Here, based on advanced material characterization techniques, such as focused ion beam (FIB), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the mi-crostructures underneath fracture surfaces were thoroughly investigated in an AM aluminium (AlSi10Mg) alloy with horizontal and vertical building orientation endured very-high-cycle fa-tigue (VHCF) loading under stress ratios R = –1, 0 and 0.5. Two VHCF failure specimens A and B were representatively selected to further SEM examine and TEM samples preparation via FIB milling. Specimen A was horizontally printed and failed at R = –1; specimen B was vertically printed and failed at R = 0. TEM samples A1 and B1 were lifted from locations near the crack ini-tiation sites on the fracture surfaces of specimens A and B; The locations of TEM samples A2 and B2 kept away from the crack origin sites but still within the “fish-eye” region of crack steady growth. TEM observations show that there was no characteristic microstructure induced by VHCF in different oriented specimens and under various R values.

We found an important fact that the beam footprint line of Ping will intersect with the real water depth when the initial incidence angle is about 45°, and sound velocity error hardly has an effect on it. This is contrary to our previous experience that the soundings of the central beam of multi-beam bathymetric system (MBS) is the most accurate. Firstly, the influence of sound velocity errors on central beam and seafloor topography distortion was analyzed. Secondly, the process of proving this fact was given, and the topography correction method was proposed by compensating the sound velocity profile area (SVP area). Finally, we showed in the first simulation of four type errors in SVPs that this fact is verified. The topography correction method used in the second simulation to correct the topography distortion of the first simulation is also verified.

Micro-electro-mechanical systems (MEMS) are once proposed in 1970s and evolving rapidly. The current researchers are seeking for better designs and better applications of MEMS actuators. This work presents an electrostatic driven dual-axis scanning micromirror, i.e., two-dimensional (2D) scanning micromirror with a mirror size of 500 μm × 500 μm. The scanning mirror is implemented by using bulk micromachining process on silicon on insulator (SOI) substrate, which is compatible with present complementary metal oxide semiconductor (CMOS) manufacturing technology. The scanning frequencies of the slow and the fast axis are 4.87 kHz and 31.15 kHz, respectively. The impact factors of the dimensions of comb fingers and torsional beams are analyzed and discussed in this study. Under the driving voltage difference of 100 volts and 70 volts, the deviation angle is 4.57° × 13.08°. Therefore, a simple design of a dual-axis MEMS scanning micromirror is proposed, which can be precisely controlled without additional complex sensors or circuits.

The 3D reconstruction of vermiculite-based sealing material was carried out based on CT scanning experiments and Avizo software. The precision and representation of the reconstructed digital core were tested by calculating the pore structure parameters and comparing them with the experimental results of mercury compression. Avizo is a perfect interface with Fluent software to perform micro-scale seepage simulation to explore the distribution of pressure and velocity fields during fluid transport. In this paper, a new approach is proposed to study the penetration leakage of non-metallic gaskets by using equivalent pore networks.

1,3,5-Tris-(α-naphthyl)benzene is an organic non-electrolyte with notable stability of an amorphous phase. Its glassy and supercooled liquid states were previously studied by spectroscopic and calorimetric methods. However, the thermodynamic parameters of phase transitions available from the literature are inconsistent. In this work, the heat capacities of crystalline and liquid phases, the temperature dependence of the saturated vapor pressures, fusion and vaporization enthalpies were determined using differential and fast scanning calorimetry and verified using the estimates based on solution calorimetry. The structural features of 1,3,5-tris-(α-naphthyl)benzene are discussed based on the computations performed and the data on the molecular refractivity. The consistency between the values obtained by independent techniques was demonstrated. The deviations in the previously published data were attributed to possible polymorphism.

The details of antigen-antibody interactions and the identification of epitopes are critical for the development of monoclonal antibody drugs. Ab42 is a native human-derived anti-CFH monoclonal antibody. In this study, the interaction between antigen pCFH and antibody (Ab42) was theoretically demonstrated by molecular docking and MD simulation, combined with free energy calculation and computational alanine scanning (CAS), and key amino acids and epitopes were identified. Experimental alanine scanning (EAS) was then carried out to verify the results of the calculation, and our results indicated that Ab42 antibody forms hydrogen bonds and interacts hydrophobically with pCFH through the Tyr315, Ser100, Gly33, and Tyr53 residues on its CDR, while the main pCFH epitopes are located at the six sites of Pro441, Ile442, Asp443, Asn444, Ile447, and Thr448. In conclusion, this study has explored the mechanism of antigen-antibody interaction from both theoretical and experimental aspects, and our results have important theoretical significance for the design and development of relevant antibody drugs.

The main goal and essential parameter of laser light conversion is achieving higher laser brightness. That is the main reason why we take one light source to pump another. For every application the desired laser beam must have the highest available beam quality and highest achievable power. Usually by increasing one parameter, you incur a loss in the other. Here we present a method for delaying the reduction in beam quality by using a spatially structured optical pump for a membrane external cavity laser resonator. A slight increase in brightness is achieved under the same focusing conditions just by changing the pump intensity profile. By using a dynamically changing pump pattern a controllable output laser mode can be achieved.

A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.

Heavy Ion Beam Probing (HIBP) diagnostic is a powerful tool for electric field studies in hot dense plasma of modern day toroidal magnetic confinement devices. On the TUMAN-3M to-kamak, the HIBP have been used in regimes with improved plasma confinement to clear up the role of radial electric field in the transition to good confinement regimes. Recently, a moderni-zation of the TUMAN-3M HIBP diagnostics was performed aiming to reconfigure it for a work with a reversed plasma current direction and improvement of overall stability of the diagnostic. The results of first measurements of plasma potential in co-NBI scenario are reported and dis-cussed.

This paper presents an approach to the two-dimensional analysis of elastic isotropic deep beams using the finite difference method (FDM). Deep beams are subjected to in-plane loading and present a shear span to height ratio of less than 2.50; consequently, Euler-Bernoulli beam theory and Timoshenko beam theory do not apply. Deep beams analysis is generally conducted using numerical methods such as the finite element method and to a lesser extent the FDM; the strut-and-tie model and the stress field method are also widely utilized. Analytical approaches usually make use of the Airy stress function, where stresses are formulated in terms of the stress function; however, the exact solution of this function satisfying all of the boundary conditions can hardly be found, even for simple cases. In this paper, deep beams were analyzed using the FDM. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected nodes of the structure. Therefore, the deep beam was discretized with a two-dimensional grid, and additional nodes were introduced at the boundaries and at positions of discontinuity (openings, brutal change of material properties, non-uniform grid spacing), the number of additional nodes corresponding to the number of boundary conditions at the node of interest. The introduction of additional nodes allowed us to apply the governing equations at boundary nodes and satisfy the boundary and continuity conditions. An Airy stress function approach and a displacement potential function approach were considered in this study whereby strong formulations of equations (equilibrium, kinematic, and constitutive) were set. Stress and stability analyses were carried out with this model; furthermore, deep beams of varying stiffness, layered beams, and beams having openings were analyzed. For slender beams, the results obtained with the Airy stress function approach showed good agreement with those of the Euler-Bernoulli beam theory, and for deep beams, the shapes of stress distributions were in good agreement with a proper understanding of the behavior of structures. On the other hand, the displacement potential function approach delivered unsatisfactory results, probably due to the use of an inefficient equation solver; a more powerful tool will be needed in future research for this purpose.

Ballistic helmets are individual armor equipment designed to protect a soldier's head from projectiles and fragments. Although very common, these helmets are responsible for several causalities due to their low ballistic resistance and large back face deformation to stop the projectile. Therefore, to enhance helmet performance, studies have focused on the development of new materials and new ballistic protection solutions. The purpose of this study was to develop and evaluate a new ballistic solution using thermoplastic-based matrices. The first matrix was based on high-density polyethylene (HDPE). The second matrix was based on HDPE modified with ex-foliated montmorillonite (MMT). The main manufacturing processes of a thermoplastic-based ballistic helmet are presented, along with its ballistic performance, according to the National Institute of Justice (NIJ) standard 0106.01 and an investigation of its failure mechanisms via a non-destructive technique. All the helmets resulted in level III-A ballistic protection. The postimpact helmets were scanned to evaluate the back face deformation dimensions, which revealed that the global cone deformation was deeper in the HDPE than in the HDPE/MMT. The failure analysis revealed an overall larger deformation area in the HDPE and HDPE/MMT helmet delamination zones in regions with a large radius of curvature than in zones with the lowest radius, which is in accordance with previous simulations from the literature.

The purpose of the present study was to develop an experimental model for studying of the intra-articular knee movements depending on the work of the knee joint and applied muscle groups in isometric stretching conditions with different tens. The experimental procedure includes ultrasound examination of a knee joint after isometric stretching of healthy men (n=32). The changes in millimeters of the distances between the femur and tibia were measured with ultrasound sonographer at three stages. The first stage was performed on ten (n=10) healthy men at five different sitting and upright positions. In the second and third experimental model stages the lower limbs loading was on 22 participants. Our hypothesis which was confirmed, was that as a result of increasing extraloads on the participants back (2, 5, 10, 15, 17, 20 kg), a intra-articular decrease in the femur-tibia cartilage surface distance wiil be observed. The accuracy of the created experimental model was improved over its three stages from 30% to 9%. Quantitative model data can help to create a mathematical model for the mechanical effects during deformation of the knee joint bone cartilage, as well as to outlines the some future tasks: increasing loading weights; enlarge participant groups; comparison men and women; healthy and pathology comparison.

Pollen analysis as a part of palynology deals with the morphological determination of pollen and spores. Different technologies with different resolutions varying from simple light microscopy to highly elaborate electron microscopy are used for the examination, depending on the area of application (e.g. sedimentology, melissopalynology, forensic palynology, etc.). To answer the question of whether laser scanning microscopy (LSM) can replace scanning electron microscopy (SEM) for the determination of pollen species, 168 species were examined using LSM. It was concluded that LSM is both efficient and easy to handle. After preparing the fresh pollen, a 3D laser scan takes 5-10 minutes and unlike using SEM, the pollen does not have to be sputtered or processed. The 3D scans can be measured quickly and easily with the integrated software and there were no observable artifacts. At magnifications up to 8545x, the image quality is comparable to that of a sputtered SEM sample whereas at higher magnifications, the SEM method is superior. Overall, pollen display by LSM is much less time consuming and more cost effective than with the SEM method.

Laser scanning is an effective tool for acquiring geometric attributes of trees and vegetation, which lays a solid foundation for 3-dimensional tree modelling. Existing studies on tree modelling from laser scanning data are vast. Nevertheless, some works don’t ensure sufficient modelling accuracy, while some other works are mainly rule-based and therefore highly depend on user inputs. In this paper, we propose a novel method to accurately and automatically reconstruct tree branches from laser scans. We first extract an initial tree skeleton from the input tree point cloud, then simplify the skeleton through iteratively removing redundant components. A global-optimization approach is performed to fit a sequence of cylinders to approximate the geometry of the tree branches. Experiments on various types of trees from different data sources demonstrate the effectiveness and robustness of our method. The resulted tree models can be further applied in the precise estimation of tree attributes, urban landscape visualization, etc.

The purpose of this study consists to verify if Er:YAG laser, at low fluences, is able to debond porcelain veneers, successfully used to improve anterior tooth esthetics, without damaging the tooth structures. A total of twelve freshly extracted teeth were used and samples were decontaminated, stored, prepared to obtain Veneers adhesion. One week after, Er:YAG laser with a non-contact sapphire tip with air-water spray was used for veneer debonding at 100 mJ of power and 30Hz of frequency (Fluence 5.91 J/cm2). Results demonstrated that veneer debonding is possible with an Er:YAG laser and that the total number of pulses does not seem related to its efficiency. SEM observation confirms that residual tooth structure is not altered when using these low fluences. Low fluences with Er:YAG laser are able to debond veneers while preserving the tooth structures. SEM observation confirmed that residual tooth structure is not altered with low fluences.

A new method for multi-shot reconstruction of high-energy photon distributions in the context of studying the interaction between a beam and a plasma in plasma wakefield acceleration (PWFA) experiments is presented. The study investigates the effects of beam perturbations on betatron radiation and analyzes how these perturbations can lead to hosing, a transverse instability that can degrade the quality of the beam. The potential of betatron radiation spectroscopy as a non-invasive diagnostic technique for PWFA experiments is also emphasized.

This study introduces numerical advancements in an alternative design for the SPS Beam Dump Facility (BDF) at CERN. The design envisions a high-power operation target made of flowing liquid lead. The BDF is a proposed versatile facility at CERN, intended for both beam-dump-like and fixed-target experiments. The target behavior is assessed, assuming a proton beam with a momentum of 400 GeV/c, a pulse frequency of 1/7.2 Hz, and an average beam power of 355 kW. An evaluation is conducted using various Computational Fluid Dynamics (CFD) codes to analyze the behavior of liquid lead and to predict the thermal stress on the target vessel induced by the pulsed heat source generated by the charged particle beam. The comparison increases the reliability of the results, investigating the dependencies on the CFD modeling approach. The beam is modeled as a volumetric heat source with data coming from beam-lead interaction simulations provided by CERN and obtained with the Monte-Carlo code FLUKA. The velocity field and stress profiles are utilized to enhance the design of the lead loop and verify its viability and safety when operated with a liquid metal target.

In this paper, we dive into the exciting world of wireless communication, focusing on how millimeter-wave technology and Multiple-Input Multiple-Output phased array antennas are shaping the future of 5G and the upcoming 6G technologies. We cover the latest advancements in millimeter-wave and beam-forming technologies, emphasizing their role in enhancing network security and efficiency in automotive vehicles through dual radar communication. Our discussion spans the benefits, applications, challenges, and solutions of these technologies individually from millimeter-wave to beam-forming technology and joint radar communications, alongside a look at their theoretical and practical implementations. We emphasize the integration of beam-forming technology in joint radar communications for future automotive vehicles and its impact on automotive systems, smart cities, and the Internet of Things (IoT). Looking ahead, we discuss the potential of these technologies to transform future tech landscapes, while also addressing the security implications of merging communication and radar capabilities. This paper aims to provide a clear view of the advancements and prospects of millimeter-wave, beam-forming, and dual radar communication technologies.

We present a compact polarimeter for 3He ions with special emphasis on the analysis of short-pulsed beams accelerated during laser-plasma interactions. We discuss the specific boundary conditions for the polarimeter, such as the properties of laser-driven ion beams, the selection of the polarization-sensitive reaction in the polarimeter, the representation of the analyzing-power contour map, the choice of the detector material used for particle identification, as well as the production procedure of the required deuterated foil-targets. The assembled polarimeter has been tested using a tandem accelerator delivering unpolarized 3He ion beams, demonstrating good performance in the few-MeV range. The statistical accuracy and the deduced figure-of-merit of the polarimetry are discussed, including the count-rate requirement and the lower limit of accuracy for beam-polarization measurements at a laser-based ion source.

The snap fit is a common mechanical mechanism. We have studied the spherical snap fit carefully for its physical asymmetry which is easy to assemble but difficult to disassemble, and obtained the general law.Because of the complexity of spherical structure, it is difficult to get a theoretical formula to describe its physical asymmetry.In this paper, through the method of combining theory, simulation and experiment, and based on the general rule of cylindrical snap fit obtained in the early stage, pushing assembly and pulling disassembly of spherical snap fit are studied,we not only get the theoretical formula of spherical snap fit, but also further verify the correctness of previous research conclusions on cylindrical snap fit.This research provides strong theoretical support and basis for the optimization design and further research of snap fit.

Gold nanoparticles (GNPs) have demonstrated significant dose enhancement with kilovoltage (kV) X-rays however recent studies have shown inconsistent findings with megavoltage (MV) X-rays. We proposed to evaluate the radiosensitization effect in U87 glioblastoma (GBM) cells in the presence of 42 nm GNPs and irradiated with a clinical 6 MV photon beam. Cytotoxicity and radiosensitization was observed using MTS and clonogenic cellular radiation sensitivity assays respectively. Sensitization enhancement ratio was calculated for 2 Gy (SER2Gy) with GNP (100 μg/mL). Dark field and MTS assay revealed high co-localization and good biocompatibility of the GNPs with GBM cells. Significant sensitization enhancement of 1.45 (P = 0.001) was observed with GNP 100 μg/mL. Similarly, at 6 Gy there was significant difference in the survival fraction between GBM alone group (Mean (M) = 0.26, Standard Deviation (SD) = 0.008) and GBM plus GNP group (M = 0.07, SD = 0.05, P = 0.03). GNPs enable radiosensitization in U87 GBM cells at 2 Gy when irradiated using a clinical platform. In addition to the potential clinical utility of GNPs, these studies demonstrate the effectiveness of a robust and easy to standardise in-vitro model that can be employed for future studies involving metal nanoparticle plus irradiation.

The article presents tests aimed to verify the possibility of making T-joints in TMCP steel using laser. The tests involved the use of 10 mm thick high yield point steel S700MC obtained in an industrial manufacturing process. The joints made in the tests were single and double-sided. Subsequent non-destructive tests revealed that the joints obtained in the tests represented quality level B in accordance with PN-EN ISO 13919-1. Single-sided welding performed using the laser beam having a power of 11 kW enabled the obtainment of 8 mm deep penetration without visibly deforming the web of the joint. The double-sided welded joints were characterised by proper geometry and the presence of gas pores in the welds not compromising the requirements of quality level B (strict requirements). The weld structure was bainitic-ferritic. The weld hardness was by approximately 60 HV1 higher than that of the base material (280 HV1). The HAZ area was slightly softer than the base material. The tests of thin foils performed using a high-resolution scanning transmission electron microscope revealed that, during welding, an increase in the content of the base material in the weld was accompanied by an increase in contents of alloying microagents Ti and Nb, particularly near the fusion line. The above-named alloying microagents, in the form of fine-dispersive (Ti,Nb)(C,N) type precipitates, could reduce plastic properties of joints.

Neutral beam injection (NBI) is used for thermonuclear plasma heating, non-inductive current drive, rotation, operation scenario control, and for plasma diagnostics in nuclear fusion devices. NBI is the main source of fast particles in plasma which transmit energy to thermal plasma during their slow-down. Steady-state tokamak operation is only possible when the sub-thermal particles energy is absorbed and effectively confined in plasma volume. While NBI purposes and applications vary through different fusion systems, the engineering tasks performed during research and development (R&D) stage of neutral beamline design have much in common. The NBI studies, especially addressing long pulse and high-power operation typically include a beam transmission analysis and power loads distribution at the structural components of the beamline. Thermo-structural analysis is applied next to heat removal circuits design. ‘Beam Transmission’ (BTR) code is a dedicated tool, developed by a physicist and used by NBI physicists and engineers. BTR was created and 1^st applied during R&D phase of the world’s largest tokamak ITER. BTR code is intended for public usage and routinely applied for detailed simulations of neutral beam propagation through complex beamlines. BTR is flexible and intuitive in input, user-friendly and fully interactive. Thanks to visualization and high performance BTR looks and feels like a real NB flight simulator. Despite BTR ‘mature’ age, the code is still in evolution. Support is available to all new BTR users.

The external and internal structures of male and female adults of Culicoides grisescens Edwards, were examined with scanning electron microscope (SEM) and tissue section techniques. Specimens were collected from Qilian Mountain National Park in Qinghai Province, China. The ultrastructure and morphology of compound eyes, antenna, maxillary palpus, spermathecae, genitalia and other structural characteristics of both male and female adults of C. grisescens are described. Internal structures of the species are described, including histological sections of the digestive, nervous, respiratory, and reproductive systems. This paper provides visual and descriptive details for the systematic taxonomic study of Ceratopogonidae.

Purpose: To examine the effectiveness of patterned laser trabeculoplasty (PSLT) as an additional treatment for patients of open-angle glaucoma (OAG) receiving maximized ocular hypotensive medications (OHM). Methods: Forty eyes of 33 patients (average age 72.7±10.7 years) who had not previously undergone open glaucoma surgery or laser trabeculoplasty and were treated with maximized OHM between June 2018 and March 2022 were included. A 360-degree PSLT was conducted and postoperative intraocular pressure (IOP) and survival curves at 1, 3, 6, 9, and 12 months were evaluated. Results: According to the Kaplan-Meier survival analysis, the average survival time was 8.1 months with death defined as postoperative IOP reduction of less than 10% or requiring additional treatment. The average survival time was 4.9 months with death defined as postoperative IOP reduction of less than 20% or requiring additional treatment. In the 31 eyes which received no additional treatment after PSLT, the mean preoperative IOP was 18.5±3.9 mmHg, which reduced to 15.3±4.1 mmHg (p=1.62 x 10-6)), 15.5±3.4 mmHg (p=1.51 x 10-5), 15.7±4.0 mmHg (p=1.75 x 10-5), 14.7±4.38 (p=2.89 x 10-6), and 15.0±4.0 mmHg (p=5.74 x 10-9) at 1, 3, 6, 9 and 12 months after PSLT, respectively. The IOP reduction rate one year after PSLT was 18.7%. Thirteen of the 31 eyes (42%) achieved a 20% reduction in IOP compared to the baseline. Conclusion: Adjunctive treatment with PSLT in OAG patients receiving maximized OHM may be effective over 12-months of follow-up.

Porous metals possess low bulk density, large specific strength, high stiffness and special thermal, electromagnetic and acoustic conductivity, so that porous metals are widely used in filtration and separation, flame retardant explosion-proof, biomedical application, etc. Compared with its corresponding dense metal, the presence of porous structures also leads to different corrosive performances of porous metal. So, some researches have utilized weight loss method, electrochemical impedance to evaluate porous metals’ corrosion behavior; however, the influence of pore structure on metal corrosion is still controversial, and present methods used for analyses of porous metals’ corrosion are statistical averages of the corrosion behavior of the entire porous material, which cannot accurately reflect the corrosion behavior inside the pore structure. Herein, we prepare porous copper samples with 0, 24, 72, 96 pores using mechanical process, and employ scanning kelvin probe combined with electrochemical polarization curve and impedance spectroscopy to test the corrosion performance of the porous copper in static and dynamic NaCl solution. The relevant results indicate that in static solution, the corrosion resistance of samples gradually increases with the rise of the number of pores. By contrast, the sample with 24 pores exhibits more susceptible to corrosion than the sample without pore.

Samples of ZrO2 ceramics with different concentrations of impurity titanium ions were synthesized by mixing powders of zirconium and titanium oxides in various mass ratios. The phase composition and surface morphology of the studied ceramics were determined by X-ray phase analysis and scanning electron microscopy. It was found that irradiation of samples with xenon ions (220 MeV) with fluences 1010 and 1012 ion/cm2 leads to a decrease in the intensity of the pulse cathodoluminescence band at 2.5 eV. It is shown that ion irradiation causes the appearance of a new peak of thermoluminescence at 450-650 K of a non-elementary form associated with radiation-induced traps of charge carriers. In contrast to electron irradiation, an increase in the fluence of ions leads to a decrease in the intensity of this peak. In contrast to electron irradiation, an increase in the fluence of ions leads to a decrease in the intensity of this peak. A complex nonmonotonic dependence of the cathode and thermoluminescence intensity on the dopant concentration was found, which may be due to the effects of concentration quenching and aggregation of defective centers.

The results of muonographic study of two objects in the cave complex of the unique historical and archaeological memorial, the Holy Dormition Pskovo-Pechersky Monastery, are presented. The experimental technology is based on the use of nuclear emulsion detectors.

The phenomenon of ordered self-assembly on solid substrates is a topic of interest in both fundamental surface science research and its applications in nanotechnology. The regulation and control of two-dimensional (2D) self-assembled supra-molecular structures on surfaces have been realized through applying external stimuli. By utilizing scanning tunneling microscopy (STM), researchers can investigate detailed phase transition process about self-assembled monolayers (SAMs), providing insight into the interplay between intermolecular weak interactions and substrate-molecule interactions, which govern the formation of molecular self-assembly. This review will discuss the structural transition of self-assembly probed by STM in response to external stimuli and provide state-of-art methods such as tip induced confinement for the alignment of SAM domains and selective chirality. Finally, we discuss the challenges and opportunities in the field of self-assembly and STM.

Diatom identification and counting by light microscopy is a fundamental method in ecological and water quality investigations. Here we present a new variant of this method based on “digital virtual slides”, and compare it to the traditional, non-digitized light microscopy workflow. We analysed three replicates of six samples using two methods: 1) working directly on a light microscope (the “traditional” counting method), and 2) preparing “virtual digital slides” by high-resolution slide scanning and subsequently identifying and labelling individual valves or frustules using a web browser-based image annotation platform (the digital method). Both methods led to comparable results in terms of species richness, diatom indices and diatom community composition. Although counting by digital microscopy was slightly more time consuming, our experience points out that the digital workflow can not only improve the transparency and reusability of diatom counts but it can also increase taxonomic precision. The introduced digital workflow can also be applied for taxonomic inter-expert calibration through the web, and for producing training image sets for deep-learning-based diatom identification, making it a promising and versatile alternative or extension to traditional light microscopic diatom analyses in the future.

Three-dimensional transfer functions (3D TFs) are generally assumed to fully describe the transfer behavior of optical topography measuring instruments such as coherence scanning interferometers in the spatial frequency domain. Therefore, 3D TFs are supposed to be independent of the surface under investigation resulting in a clear separation of surface properties and transfer characteristics. In this paper we show that the 3D TF of an interference microscope differs depending on whether the object is specularly reflecting or consists of point scatterers. In addition to the 3D TF of a point scatterer, we will derive an analytical expression for the 3D TF corresponding to specular surfaces and demonstrate this as being most relevant in practical applications of coherence scanning interferometry (CSI). We additionally study the effects of temporal coherence and disclose, that in conventional CSI temporal coherence effects dominate. However, narrowband light sources are advantageous if high spatial frequency components of weak phase objects are to be resolved, whereas for low-frequency phase objects of higher amplitude the temporal coherence is less affecting. Finally, we present an approach that explains the different transfer characteristics of coherence peak and phase detection in CSI signal analysis.

TThe paper presents the results of research on the influence of the settings of lubrication and cooling system parameters (solenoid valve opening time and lubricant feed pressure in terms of its quantity) in order to select the optimal lubricating conditions and thus reduce the wear of the dies used in the first forging operation of the valve forging made of high-nickel steel. Based on the observation of lubrication in the industrial process, it was found that a significant part of the lubricant fails to reach the die cavity, reaching the outside of it, which causes die wear due to seizure resulting from adhesion of the forging material to the tool surface, as well as high lubricant consumption and dirt in the press chamber. The authors proposed their own mobile lubricating and cooling system, which allows for a wide range of adjustments and provided with automatic cleaning procedures of the entire system, unlike the fixed lubrication system used so far in the industrial process. First, tests were carried out in laboratory conditions to determine the highest wettability and the lubricant remaining inside the tool cavity. These tests determined the lubrication system parameter settings which ensured that the greatest amount of lubricant remains in the cold die cavity without the forging process. Then, to verify the obtained results, tests were carried out in the industrial process of hot die forging of valve forgings, for short production runs of up to 500 forgings. The results were compared with the measurement of changes in the geometry of tools and forgings based on 3D scanning and surface topography analysis with the use of SEM. For best results (the variant of the setting of the dose and the time of exposure to lubricant), the forging process was carried out with the use of a new tool, up to the maximum service life.

Scanning magnetic microscopy is a new tool that has recently been used to map magnetic fields with good spatial resolution and field sensitivity. This technology has great advantages over other instruments; for example, its operation does not require cryogenic technology, which reduces its operational cost and complexity. Here, we describe the construction of a customizing scanning magnetic microscope based on commercial Hall-effect sensors at room temperature that achieves a spatial resolution of 200 µm. Two scanning stages on the x- and y-axes of precision, consisting of two coupled actuators, control the position of the sample, and this microscope can operate inside or outside a magnetic shield. We obtained magnetic field sensitivities better than 521 nT_rms/√Hz between 1 and 10 Hz, which correspond to a magnetic momentum sensitivity of 9.20 × 10^–10 Am². In order to demonstrate the capability of the microscopy, polished thin sections of geological samples, samples containing microparticles and magnetic nanoparticles were measured. For the geological samples, a theoretical model was adapted from the magnetic maps obtained by the equipment. Vector field maps are valuable tools for the magnetic interpretation of samples with a high spatial variability of magnetization. These maps can provide comprehensive information regarding the spatial distribution of magnetic carriers. In addition, this model may be useful for characterizing isolated areas over samples or investigating the spatial magnetization distribution of bulk samples at the micro and millimeter scales. As an auxiliary technique, a magnetic sweep map was created using Raman spectroscopy; this map allowed the verification of different minerals in the samples. This equipment can be useful for many applications that require samples that need to be mapped without a magnetic field at room temperature, including rock magnetism, the nondestructive testing of steel materials and the testing of biological samples. The equipment can not only be used in cutting-edge research but also serve as a teaching tool to introduce undergraduate, master's and Ph.D. students to the measurement methods and processing techniques used in scanning magnetic microscopy.

We improved a magnetic scanning microscope for measuring the magnetic properties of minerals in thin sections of geological samples at submillimeter scales. The microscope is comprised of a 200 µm diameter Hall sensor that is 142 µm from the sample; an electromagnet capable of applying to the sample up to 500 mT dc magnetic fields over a 40 mm diameter region; a second Hall sensor arranged in a gradiometric configuration to cancel the background signal applied by the electromagnet and reduce overall noise in the system; a custom-designed electronics to bias the sensors and provide adjustment for background signal cancelation; and a scanning XY stage with micrometer resolution. Our system achieves a spatial resolution of 220 µm with noise at 6.0 Hz of »300 nT_rms/(Hz)^1/2 in an unshielded environment. The magnetic moment sensitivity is 1.3 × 10⁻¹¹ Am².^1/2 We successfully measured the representative magnetization of a geological sample using an alternative model that takes into account the sample geometry and identified different micrometric characteristics in the sample slice.

The diameter of a H13 steel tool with M6 threads and a pin diameter of 5.9 mm and a pin length of 5 mm was measured after each 25.4 mm length of friction stir processing (FSP) of 6061-T6 extrusions. The change in pin diameter with FSP time or distance did not exhibit any steady state and was found to have two distinct regions. Metallographic analysis of two tools subjected to FSP for 60 and 120 seconds showed that (i) threads fractured in early stages of FSP, (ii) a built-up layer formed between the threads, and (iii) threads progressively wore with processing time. The metallographic analysis of an embedded tool showed the presence of a fractured piece of the tool in the stir zone. These points are discussed in detail in the paper.

This article presents a methodology to process information from a Terrestrial Laser Scanner (TLS) from three dimensions (3D) to two dimensions (2D), and to two dimensions with a color value (2.5D), as a tool to document and analyze heritage buildings. Principally focused on the loss of material in stone, this study aims at creating an evaluation method for loss control, taking into account the state of conservation of the building in terms of restoration, from studying the pathologies, to their identification and delimitation. A case study on the Cathedral of the Seu Vella de Lleida was completed, examining the details of the stone surfaces. This cathedral was affected by military use, periods of abandonment, and periodic restorations.

We describe a family of paraxial and quasi-monochromatic optical wave packets with finite energy and smoothly shaped amplitude in space and time that develops a singularity in the intensity when spatiotemporally focused by imparting a converging spherical wave front and a negative temporal chirp. This singular behavior upon ideal focusing is manifested in actual focusing with finite apertures and in media with high-order dispersion in an "exploding" behavior featuring indefinitely increasing concentration of the energy when opening the aperture radius, thus exercising a continuous control on the focal intensity and spatial and temporal resolution. These wave packets offer a new way of focusing that outperforms what can be achieved with standard Gaussian wave packets in terms of focal intensity and resolution, and new possibilities in applications where energy concentration and its control are crucial.

In this paper we present methodology for precise calibration of Molecular Beam Epitaxy (MBE) growth process and achieving run to run stability of growth parameters. We present the analysis of the influence of fluxes stability during the growth of long wavelength quantum cascade laser structures designed for the range λ ~ 12–16 µm on wavelength accuracy with respect to desired emission wavelength. The active region of the lasers has a complex structure of nanometer thickness InxGa1-xAs/InyAl1-yAs superlattice. As a consequence, the compositional and thickness control of the structure via bulk growth parameters is rather difficult. To deal with this problem we employ methodology based on double-superlattice test structures, that precede the growth of the actual structures. The test structures are analyzed by high-resolution X-ray diffraction which allows to calibrate the growth of the complex active region of quantum cascade laser structures. We also study theoretically the effect of individual flux changes on emission wavelength and gain parameters of the laser. The results of simulations allow for determination of flux stability tolerance, preserving acceptable parameters of the laser and provide means of emission wavelength control. The proposed methodology was verified by the growth of laser structures for emission at around 13.5 μm.

The pion-argon cross-section measurement is crucial to understand effects such as final-state interactions, which account for a large source of systematic uncertainty in neutrino oscillation experiments. ProtoDUNE-SP, with its charged particle beam data, can provide such experimental constraints. This paper elaborates the methodology to measure the cross-section on large-scale LArTPCs like ProtoDUNE-SP. We use the 1 GeV MC sample to demonstrate the analysis procedures. The cross-sections for pion kinetic energy ranging from 350 MeV to 950 MeV are measured on the MC. The consistency of the MC results with its input values serves as validation of the method and the procedures, which we will later use to perform measurements on the data sample.

Snap fit is a common mechanical mechanism. It uses the physical asymmetry that is easy to assemble but difficult to disassemble to provide a simple and fast link between objects. The ingenious combination of geometric shape, bending elasticity and friction of the snap fit is the mechanism behind the easy to assemble but difficult to disassemble disassemble. Yoshida and Wada (2020) has done a groundbreaking work in the analysis of the elastic snap fit. During our study of their paper, while we really enjoyed their research, unfortunately we detected several questioning formulations. After careful checking, we found that those formulations are not typographical, therefore it is necessary to make corrections. This paper reformulates the linear elasticity of a cylindrical snap fit, obtains an exact solution and proposes an accurate relation between the opening angle and bending tangent angle. Under the first order approximation, our formulations can reduced to the results of Yoshida and Wada and hence confirms the scientific correctness of Yoshida and Wada's work. Furthermore, this paper also derives a correct vertical displacement expression, and propose a new way of disassembly by bending for the first time and formulate a scaling law by data fitting. All formulations are validated by finite element simulation and experiment. The research here is helpful to the design of elastic snap fit or adjustable mechanical mechanism and metamaterial cell.

Identifying cracks in the incipient state is essential to prevent the failure of engineering structures. Detection methods relying on the analysis of the changes in modal parameters are widely used because of the advantages they present. In our previous research, we have found that eigenfrequencies were capable of indicating the position and depth of damage when sufficient vibration modes were considered. The damage indicator we developed was based on the relative frequency shifts (RFS). To calculate the RFSs for various positions and depths of a crack, we established a mathematical relation that involved the squared modal curvatures in the healthy state and the deflection of the healthy and damaged beam under dead mass, respectively. In this study, we propose to calculate the RFS for beams with several cracks by applying the superposition principle. We demonstrate that this is possible if the cracks are far enough from each other. In fact, if the cracks are close to each other, the superposition method does not work and we distinguish two cases: (i) when the cracks affect the same beam face, the frequency drop is less than the sum of the individual frequency drops, and (ii) on the contrary, cracks on opposite sides cause a decrease in frequency, which is greater than the sum of the frequency drop due to individual damage. When the RFS curves are known, crack assessment becomes an optimization problem, the cost function being the distance between the measured RFSs and all possible RFSs for several vibration modes. Thus, the RFS constitutes a benchmark that characterizes damage using only the eigenfrequencies. We can accurately locate multiple cracks and estimate their severity trough experiments and thus prove the reliability of the proposed method.

Polymethyl methacrylate (PMMA) is a transparent thermoplastic with excellent optical properties, transparent surface, low moisture absorption, tensile and electrical resistance. In this study, the alloy was prepared through PMMA and cycloolefin copolymer (COC) due to some similar properties. The mechanical test showed that properties such as impact resistance, elongation, tensile, and flexural strength decreased by adding COC by up to 20% due to less incompatibility and miscibility, but mentioned properties improved by adding COC 40% due to sub-phase generation. The DSC and DMTA tests showed improvement in the thermal properties of alloys by adding 40% COC. SEM micrographs exhibited a softer surface and more phase elongation of the alloy. Finally, the sample was selected as the optimal sample in terms of mechanical properties irradiated by electron beam, and amplification results showed that a dose of 50 KGY increased the mechanical and thermal properties relatively.

Background: Cleft lip and palate can affect the development of the maxilla, which may create a midfacial deficiency as well as an interference of the facial growth pattern and dentofacial esthetics. Objective: Estimate the chronological age of complete fusion of the spheno-occipital synchondrosis in cleft lip and/or palate patient´s and a control group, using cone beam computed tomography images. Methods: In this retrospective study, 125 patients were enrolled (cleft lip and/or palate group (n=91); control group (n=34)). Age comparison was made with Chi-square test and a Kaplan-Meyer analysis determined the median time to reach complete fusion of the spheno-occipital synchondrosis (p<0.05). Results: The experimental group showed statistically significant differences in the median time for complete ossification between males and females (p=0.019). No statistically significant differences were found in the control group between males and females (p=0.104). The median time for complete ossification of the spheno-occipital synchondrosis was, for males, 15.0 years in both groups; for females, it was 14.0 years in the experimental group and 13.0 years in the control group. Conclusions: The present study showed no differences in the ossification of the spheno-occipital synchondrosis between individuals with and without cleft lip and/or palate.

We present the generation and nonlinear frequency conversion of nanosecond cylindrical vector beams (CVBs) in two-mode fiber (TMF). Based on the polarized dependence vector mode coupling characteristic and the precise wavelength tunability of an acoustically-induced fiber grating (AIFG), the nanosecond cylindrical vector beams (CVBs, 1064 nm, 10 ns) is directly generated in a TMF with convenient switching characteristics between the radial and azimuthal vector beams. Furthermore, the stimulated Raman scattering (SRS) is produced based on the transmission of the nanosecond CVBs in the 100-meters long TMF, and the spatial intensity and polarization distributions characteristics the 1st-order Stokes shifted component is consistent with the nanosecond CVBs pump pulse. This work provides a method for achieving wavelength conversion of the CVBs in optical fiber.

In the last decades bioresorbable and biodegradable polymers have gained a very good reputation both in research and in industry thanks to their unique characteristics. They are, indeed, able to ensure high performances and biocompatibility, at the same time avoiding post-healing surgical interventions for devices removal. In the medical device industrial use of such biopolymers, it is widely known that product formulation and manufacturing need to follow specific procedures in order to ensure both proper mechanical properties and desired degradation profile. Moreover, also the sterilization method is crucial and its impact on physical properties is generally underestimated. In this work we focused our attention on the effect of different terminal sterilization methods on two commercially available poly(L-lactide-co-ε-caprolactone) with equivalent chemical composition (70% PLA and 30% PCL) and relatively similar initial molecular weight, but different chains arrangement and crystallinity. Results obtained show that crystallinity plays a key role, helping in preserving the narrow distribution of chains and, as a consequence, defined physical properties. These statements can be used as guidelines for a better choice of the most adequate biodegradable polymers in the production of resorbable medical devices.

In previous work (Z. Angew. Math. Phys. 68(2), 2017), Apalara considered a one dimensional thermoelastic laminated beam under Cattaneo’s law of heat conduction and proved the exponential and polynomial decay results depend on the stability number χ_T . In this paper, we continue to study the same system and show that the solution of the concerned system lacks of exponential decay result in the case χ_T ≠ 0 which solves the open problem proposed by Apalara (Z. Angew. Math. Phys. 68(2), 2017).

Directional dithering of a laser beam potentially limits the detection accuracy of a laser triangulation displacement probe. A theoretical analysis indicates that the measurement accuracy will linearly decrease as the laser dithering angle increases. To suppress laser dithering, a laser triangulation displacement probe with laser beam pointing control, which consists of a collimated red laser, a laser beam pointing control setup, a receiver lens, and a charge-coupled device, is proposed in this paper. The laser beam pointing control setup is inserted into the source laser beam and the measured object and can separate the source laser beam into two symmetrical laser beams. Hence, at the angle at which the source laser beam dithers, the positional averages of the two laser spots are equal and opposite. Moreover, a laser dithering compensation algorithm is used to maintain a stable average of the positions of the two spots on the imaging side. Experimental results indicate that with laser beam pointing control, the standard variance of the fitting error decreases from 0.3531 to 0.0100, the repeatability accuracy can be decreased from ±7mm to ±5 μm, and the nonlinear error can be reduced from ±6 %FS to ±0.16 %FS.

The paper presents the results of high precision control survey carried out in the underground mining of Oyu Tolgoi project using terrestrial laser scanning technology. The purpose of the measurements is to ensure the heading, total length and volume of the penetration and excavation works are being implementing in accordance with the planned and designed dimensions. We established a network of 18 reference points in the tunnel of the selected underground level which were repeatedly measured 4 times by two round readings of the Trimble S7 tacheometry and processed by using the Trimble Business Center software. All points except the one was within the permissible error. Based on these points the excavation length and volumes were determined using the Trimble SX12 laser scanner. The difference between the planned work quantity provided by the Oyu Tolgoi project and the actual values measured by the laser scanning was calculated using the comparative method. The TLS partial control measurements in the excavations made through the ore bodies revealed the length of 20285.72 m and volume of 441128.80 m3 for underground 7 mine levels while their project values were 16158.26 m length and 422837.50 m3 volume, respectively.

The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

Under inflammatory conditions including lymphatic disorders, bone marrow-derived myeloid cells often express lymphatic endothelial cell (LEC) markers called LEC progenitor cells, which extend lymphatic vessels by fusing with existing lymphatic vessels. However, studies on the mechanism of lymphatic regeneration using three-dimensional images of lymphatic structures are limited. In this study, scanning electron microscopy (SEM) was used to observe the three-dimensional structure of lymphangiogenesis in a mouse model of secondary lymphedema. The model was established in C57BL/6J mice via circumferential incision in the inguinal region of the left hind limb. Skin samples were obtained from the lymphedema region on days 2, 5, and 8 after surgery. To determine lymphatic vessel positions using SEM analysis, we detected anti-lymphatic vessel endothelial hyaluronan receptor 1 (LYVE-1) immunoreactivity in serial sections and overlaid them during SEM observation. On days 2 and 5, spherical cells, probably myeloid cells, were attached and fused to the LYVE-1-positive lymphatic vessel walls. On day 8, spherical cells were converted to string-shaped cells, forming a new lymphatic vessel wall resembling an intraluminal pillar. Our results show the three-dimensional lymphatic structures formed during lymphatic regeneration.

The CC chemokine receptor 3 (CCR3) is a receptor for CC chemokines, including CCL5/RANTES, CCL7/MCP-3, and CCL11/eotaxin. CCR3 is expressed on the surface of eosinophils, basophils, a subset of Th2 lymphocytes, mast cells, and airway epithelial cells. CCR3 and its ligands are involved in airway hyperresponsiveness in allergic asthma, ocular allergy, and cancers. Therefore, CCR3 is an attractive target for those therapies. Previously, anti-mouse CCR3 (mCCR3) monoclonal antibodies (mAbs), C3Mab-3 (rat IgG2a, kappa), and C3Mab-4 (rat IgG2a, kappa) were developed using the Cell-Based Immunization and Screening (CBIS) method. In this study, the binding epitope of these mAbs was investigated using flow cytometry. The CCR3 extracellular domain-substituted mutant analysis showed that C3Mab-3, C3Mab-4, and a commercially available mAb (J073E5) recognized the N-terminal region (amino acids 1–38) of mCCR3. Next, the alanine scanning was conducted in the N-terminal region. The results revealed that Ala2, Phe3, Asn4, and Thr5 of mCCR3 are involved in C3Mab-3 binding, whereas Ala2, Phe3, and Thr5 are essential to C3Mab-4 binding, and Ala2 and Phe3 are crucial to J073E5 binding. These results reveal the involvement of the N-terminus of mCCR3 in the recognition of C3Mab-3, C3Mab-4, and J073E5.

Abstract: The calibrator is one of the most important factors in the calibration of various laser 3D scanning instruments. The requirements for diffuse reflection surface are specially emphasized in many national standards. In this study, the spherical calibrator and plane calibrator compara-tive measurement experiments were carried out. The black ceramic standard sphere, white ce-ramic standard sphere, metal standard sphere, metal standard plane and white ceramic standard plane were used to test the laser 3D scanner. In the spherical calibrators comparative measure-ment experiments, the results indicated that the RMS of the white ceramic spherical calibrator with reflectance about 60% is 10 times that of the metal spherical calibrator with the reflectance of about 15%, and the RMS of the black ceramic spherical calibrator with reflectance of about 11% is of the same order as the metal spherical calibrator. In the plane calibrators comparative measurement experiments, the RMS of flatness measurement is 0.077 mm for metal plane cali-brator with reflectance of 15%, and 2.915 mm for ceramic plane calibrator with reflectance of 60%. The results show that when the optimal measurement distance and incident angle are selected, the reflectance of the calibrator has a great effect on the measurement results, regardless of the outlines or profiles. Based on the experiments, it is recommended to use the spherical calibrator or the standard plane with reflectance of around 18% as the standard, which can obtain the rea-sonable results. In addition, it is necessary to clearly provide the material category and surface reflectance information of the standard when calibrating the scanner according to the measure-ment standard.

In horses, there is an increasing interest in developing long-lasting drug formulations, with bi-opolymers as viable carrier alternatives in addition to their use as scaffolds, suture threads, screws, pins, and plates for orthopedic surgeries. This communication focuses on the prolonged biocompatibility and biodegradation of PLA, prepared by hot pressing at 180 ºC. Six samples were implanted subcutaneously on the lateral surface of the neck of one horse. The polymers remained implanted for 24 to 57 weeks. Physical examination, plasma fibrinogen, and the mechanical noci-ceptive threshold (MNT) were performed. After 24, 28, 34, 38, and 57 weeks, the materials were removed for histochemical analysis using hematoxylin-eosin and scanning electron microscopy (SEM). There were no essential clinical changes. MNT decreased after the implantation procedure, returning to normal after 48h. A foreign body response was observed by histopathologic evalua-tion up to 38 weeks. At 57 weeks, no polymer or fibrotic capsules were identified. SEM showed surface roughness suggesting a biodegradation process, with an increase in the average pore di-ameter. As in the histopathological evaluation, it was not possible to detect the polymer 57 weeks after implantation. PLA showed biocompatible degradation and these findings may contribute to future research in the biomedical area.

The article proposes an indirect measurement method based on a dimensional and shape analysis of forgings for the evaluation of the manufacture and the proper operation of the key elements of the crank press, in which after modernization, a quick tool assembly based on SMED (Single Minute Exchange of Die) was implemented. As a result of the introduced changes aiming at improving the forging aggregate and increasing the production efficiency, errors were observed on the manufactured products-forgings in the form of twists and joggles. The preliminary analysis showed that they can be clearances and dynamic deformation in the kinematic chain, the occurrence of side forces during automatic forging of the forging in a two-component system (a long, thin element), as well as the design and construction errors in the joining of the SMED instrument with the table tops of the press. In order to solve the presented problem, in the first place, a separate dimensional and shape analysis was made of selected elements of the press and the instrumentation with the use of the 3D scanning method with the purpose to analyze the construction tolerances of the key elements of the press geometry. Next, an evaluation of the effect of clearances and dynamic deformations of the press as well as the force distribution during the forging process was made through numerical modelling. Despite all of the above, such an approach did not make it possible to solve the problem. A proprietary method with the use of 3d reverse scanning was proposed, which allowed to solve the problem of forgings errors. Based on the measurement results and analyses for a few variants of production cycles the necessary changes was obtained, making it possible to minimize the errors and obtain proper products in respect of geometry and quality.

Blood Concentrates (BCs) are autologous non-transfusional therapeutical preparations with biological properties applied in tissue regeneration. These BCs differ in the preparation method, in fibrin network architecture, growth factors release as well as in platelet/cell content. Methodological changes result in distinct matrices that can compromise their clinical effectiveness. The present study evaluated the influence of different g-forces and types of tubes in the release of vascular endothelial growth factor (VEGF) from platelet-rich fibrin (PRF) as a function of time. The PRF-like samples were obtained with three g-forces (200, 400, and 800 x g) for 10 minutes in pure glass tubes or in polystyrene-clot activator tubes. Scanning and Transmission electron microscopy was used to morphometric analyzes of PRF’s specimens and flow cytometry was used to quantify VEGF slow release until 7 days. Our results showed that platelets were intact and adhered to the fibrin network, emitting pseudopods and in degranulation. The fibrin network was rough and twisted with exosomic granulations impregnated on its surface. An increase in the concentration of VEGF in the PRF supernatant was observed until 7 days for all g forces (200, 400 or 800 x g), with the highest concentrations observed with 200 x g, in both tubes, glass or plastic. Morphological analyzes showed a reduction in the diameter of the PRF fibers after 7 days. Our results showed that g-force interferes with the shape of the fibrin network in the PRF, as well as affect the release of VEGF stored into platelets. This finding may be useful in applying PRF to skin lesions, in which the rapid release of growth factors can favor the tissue repair process. Our observations point to a greater clarification on the methodological variations related to obtaining PRF matrices, as they can generate products with different characteristics and degrees of effectiveness in specific applications.

This paper focused on impact localization of composite structures, which possess more complexity in the guided wave propagation because of the anisotropic behavior of composite materials. In this work, a composite plate was manufactured by using a compression molding process with proper pressure and temperature cycle. Eight layers of woven composite prepreg were used to manufacture the composite plate. A structural health monitoring (SHM) technique is implemented with piezoelectric wafer active sensors (PWAS) to detect and localize the impact on the plate. There are two types of impact event are considered in this paper (a) low energy impact event (b) high energy impact event. Two clusters of sensors recorded the guided acoustic waves generated from the impact. The acoustic signals are then analyzed using a wavelet transform based time-frequency analysis. The proposed SHM technique successfully detect and localize the impact event on the plate. The experimentally measured impact locations are compared with the actual impact locations. An immersion ultrasonic scanning method was used to visualize the composite plate before and after the impact event. A high frequency 10 MHz 1-inch focused transducer was used to scan the plate in the immersion tank. Scanning results show that there is no visible manufacturing damage in the composite plate. However, clear impact damage was observed after the high-energy impact event.

Laser scanning systems make use of Light Detection and Ranging (LiDAR) technology to acquire accurately georeferenced sets of dense 3D point cloud data. The information acquired using these systems produces better knowledge about the terrain objects which are inherently 3D in nature. The LiDAR data acquired from mobile, airborne or terrestrial platforms provides several benefit over conventional sources of data acquisition in terms of accuracy, resolution and attributes. However, the large volume and scale of LiDAR data have inhibited the development of automated feature extraction algorithms due to the extensive computational cost involved in it. Moreover, the heterogeneously distributed point cloud, which represents objects with varying size, point density, holes and complicated structures pose a great challenge for data processing. Currently, geospatial database systems do not provide a robust solution for efficient storage and accessibility of raw data in a way that data processing could be applied based on optimal spatial extent. In this paper, we present Global LiDAR and Imagery Mobile Processing Spatial Environment (GLIMPSE) system that provides a framework for storage, management and integration of 3D LiDAR data acquired from multiple platforms. The system facilitates an efficient accessibility to the raw dataset, which is hierarchically represented in a geographically meaningful way. We utilise the GLIMPSE system to automatically extract road median from Airborne Laser Scanning (ALS) point cloud. In the first part of this paper, we detail an approach to efficiently retrieve the point cloud data from the GLIMPSE system for a particular geographic area based on user requirements. In the second part, we present an algorithm to automatically extract road median from the retrieved LiDAR data. The developed road median extraction algorithm utilises the LiDAR elevation and intensity attributes to distinguish the median from the road surface. We successfully tested our algorithms on two road sections consisting of distinct road median types based on concrete and grass-hedge barriers. The use of GLIMPSE improved the efficiency of the road median extraction in terms of fast accessibility to ALS point cloud data for the required road sections. The developed system and its associated algorithms provide a comprehensive solution to the user's requirement for an efficient storage, integration, retrieval and processing of large volumes of LiDAR point cloud data. These findings and knowledge contribute to a more rapid, cost-effective and comprehensive approach to surveying road networks.

The increased availability of high resolution remote sensor data for precision agriculture 1 applications permits users to aquire deeper and more relevant knowledge about crops states that lead 2 inevitably to better decisions. The algorithm libraries being developed and evolved around these 3 applications rely on multi-spectral or hyper-spectral data acquired by using manned or unmanned 4 platforms. The current state of the art makes thorough use of vegetational indicies to guide the 5 operational management of agricultural land plots. One of the most challenging sub-problems is 6 to correctly identify and separate crop from soil. Thresholding techniques based on Normalized 7 Difference Vegetation Index (NDVI) or other such similar metrics have the advantage of being simple, 8 easy to read transformations of the data packed with useful information. Obvious difficulties arise 9 when crop/tree and soil have similar spectral responses as in case of grass filled areas in vineyards. 10 In this case grass and canopy are close in terms of NDVI values and thresholding techniques will 11 generally fail. Radiometric approaches could be integrated or replaced by a geometric approach that 12 is based on terrain data like Digital Surface Models (DSMs). These models are one of the ouputs 13 of orthorectification engines usually present in data acquired by using unmanned platforms. In 14 this paper we present two approaches based on DSM that are able to segment crop/tree from soil 15 while over gradient terrain. The DSM data are processed through a two dimensional data slicing or 16 reduction technique. Each slice is separately processed as a one dimensional time series to derive the 17 terrain and tree structures separately, here interpreted as object probability densities. In particular 18 the first approach is a Cartesian grid rasterization (CARSCAN) of the terrain and the second is its 19 immediate generalisation or radial grid rasterization of the DSM model (FANSCAN). The FANSCAN 20 recovers information from the original image at greater frequencies on the Fourier plane. These 21 approaches enable the identification of crop/tree from soil in case of slopes or hilly terrain without 22 any constraint on the displacement / direction of plant/tree row. The proposed algorithm uses pure 23 DSM information even if it is possible to fuse its output with other classifiers.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

Background/Objectives: To evaluate incidental findings in the mandible after the placement of dental implants using a new cone-beam computed tomography (CBCT) software. Methods: The initial sample consisted of 2,872 CBCT scans of patients of both sexes. The parameters evaluated in this study were the location of the implants in the mandible, implant length, anatomical relationship of the implant with the mandibular canal, presence or absence of damage to the adjacent teeth, presence or absence of implant fractures, and presence or absence of bone support. Fisher's exact test was performed to compare the variables. The significance level was set at p = 0.05. Results: Out of 2,872 CBCT scans, 214 images of patients with an average age of 44.5 years were included. The most frequent location of the implants was the posterior region (93.5%), with 54% of the implants having a length between 9 and 14 mm. It was found that 92% of the implants were positioned above the mandibular canal. Three damage to adjacent teeth was observed, with no correlation with the implant positioning (p = 0.999). In 100% of cases of implants in the anterior region, there was bone support. Fracture was observed in 1.7% of implants with a length between 9- and 14-mm. Conclusions: The installation of implants in the mandible occurs more frequently in the posterior region, with a high presence of bone support and a low incidence of damage to adjacent teeth, anatomical structures, and fractures.

Laser-plasma interactions of ultra-short laser pulses with solid targets can generate highly intense pulses of protons and ions with energies of several MeV. The spectra of these particles are spread over a wide range following a Maxwellian distribution. We report on the design and testing of a magnetic chicane for the selection of protons within a limited energy window. It consists in two successive, anti-parallel dipole fields generated by cost-effective, permanent C-magnets with customized configuration and longitudinal positions. The chicane has been implemented into the target vessel of a petawatt laser facility under constraints on the direction of the incoming laser beam and guidance of the outgoing particles through a vacuum port. The separation of protons and carbon ions within distinct energy intervals has been demonstrated and compared to a ray tracing code.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

In a concrete beam initially crack is generated at the tension side under the effect of flexure, shear and torsional loadings. Accordingly, these weak concrete members require repair and/or strengthening to increase or restore their internal load capacity. In the current experimental and numerical investigations on concrete beam having different width to depth ratio of notch on its ultimate flexural load under one-point loading was considered. Further, the flexural behavior performance of notch concrete beam repaired with the three repair materials cement mortar, bacterial mortar and adhesive was also examined. Consequently, a comparative study is imple-mented between the experimental and numerical results. Concrete Damage plasticity (CDP) model was used for finite element numerical analysis of beam. The differences in numerical and experimental measured results ranges from 0.65 - 22.20 % for the ultimate load carrying capacity. As the notch size increases the ultimate load carrying capacity of beam was reduced. Addition-ally, linear regression model is used to predict the ultimate load values at an interval of 5 mm notch width up to maximum width of notch 100 mm. It can be observed that the ultimate load capacity for repaired beam is increased as compared to the notch beam for all the three repairing materials under consideration. The maximum ultimate load was increased in case of notch beam repaired using adhesive. As compared to the cement mortar the performance of the bacterial mortar in terms of the ultimate load was more. The bacterial mortar is found more sustainable and more durable as a repair material for the concrete structures.

The use of friction-based Beam-to-Column Connections (BCC)s for earthquake-resistant Moment Resistant Frames (MRFs), aiming at eliminating damage to beam end sections due to the development of plastic hinges, has taken hold since the early eighties. Different technical solutions were proposed for steel structures, some were also designed for timber structures, while few more recent studies concern friction joints employed in reinforced concrete structures. Research aimed at characterizing the behavior of joints has focused on the evaluation of the tribological properties of the friction materials, coefficient of friction, shape and stability of the hysteresis cycles, influence of the temperature, speed of load application, effects of the application method, stability of preload, the influence of seismic excitation characteristics on the structural response, statistical characterization of amplitude and frequency of the slip excursion during seismic excitation. Studies aimed at identifying the design parameters capable of optimizing performance have focused attention mainly on the slip threshold, device stiffness, and deformation capacity. This review compiles the main and most recent solutions developed for MRFs. Furthermore, the pros and cons for each solution are highlighted, focusing on the dissipative capacity, shape and stability of hysteresis loops. In addition, the common issues affecting all friction connections, namely characteristics of friction shims and the role of bolt preload, are discussed. Based on the above considerations, a guideline can be outlined, which can help to choose the appropriate solutions for beam-to-column connections for MRFs.

The insufficient toughness of concrete can lead to the occurrence of crack expansion, ultimately resulting in a decline in the physical and mechanical properties such as bearing capacity and deformation characteristics of structural components. In severe cases, this may lead to brittle failure, where the entire structure and system fail suddenly without significant deformation after being stressed. Additionally, during the process of shear and bending failure of reinforced concrete beams, the cracks generated on the side of the beam are mostly I-II composite cracks. Considering the material nonlinearity and geometric irregularity of reinforced concrete, it is of great significance to study the dynamic evolution law of crack expansion in reinforced concrete members. Based on experimental data, this paper aims to utilize the nonlinear finite element simulation software Abaqus to conduct finite element simulations of crack expansion in simple supported reinforced concrete beams. By accurately controlling the constitutive curves of concrete and reinforcement materials, the design of seismic performance of structural members can be enhanced, thereby making essential contributions to the preliminary analysis of actual crack control engineering. The nonlinear finite element results indicate that the joint cracks of the frame with the floor slab primarily manifest as flexural cracks, with the concrete damage degree of the floor slab being higher than that of the beam. This finding underscores the importance of considering the behavior of concrete and reinforcement materials in designing for seismic performance and crack control in actual engineering applications.

Ion beam-assisted deposition (IBAD) has been proposed as a promising texturing technology that uses film epitaxy method to obtain biaxial texture on a non-textured metal or compound substrate. Magnesium oxide (MgO) is the most well explored texturing material. In order to obtain the optimal biaxial texture, the actual thickness of the IBAD-MgO film must be controlled within 12 nm. Due to the bombardment of ion beams, IBAD-MgO has large lattice deformation, poor texture and many defects in the films. In this work, an additional homogeneous epitaxy MgO (epi-MgO) layer has been deposited on the IBAD-MgO layer by electron-beam evaporation. The biaxial texture can be optimized by the deposition of additional epi-MgO layer. The effects of growth temperature, film thickness, deposition rate and oxygen flux on the texture and morphology of the epi-MgO film were systematically studied. After the research of epi-MgO process, the best full width at half maximum (FWHM) values were 2.2 for the out-of-plane texture and 4.8° for the in-plane texture, respectively. Subsequently, the LaMnO3 cap layer and YBa2Cu3O7-x (YBCO) functional layer was deposited on the epi-MgO layer to test the quality of MgO layer. Finally, the critical current density of YBCO films is 6MA/cm2 (77K, 500nm, self-field), indicating that this research provides a high-quality MgO substrate for the YBCO layer.

This study aimed to estimate scattered radiation and its spatial distribution around three Cone Beam Computed Tomography (CBCT) devices, in order to determine relatively safe positions for an operator to stand if needed to be inside the CBCT room. The following devices were tested: Morita Accuitomo (CBCT1), Newtom Giano HR (CBCT2), Newtom VGi (CBCT3). Scattered radiation measurements were performed using different kVp, mA and Field of View (FOV) options. An anthropomorphic phantom (NATHANIA) was placed inside the x-ray gantry to simulate clinical conditions. Scattered measurements were taken with the ionization chamber Inovision model 451P Victoreen once placed at fixed distances from each irradiation isocenter, away from the primary beam. A statistically significant (p<0.001) difference was found in the mean value of the scattered radiation estimations between the CBCT devices. Scattered radiation was reduced with a different rate for each CBCT device as distance was increased. For CBCT1 the reduction was 0.047μGy, for the CBCT2 0.036 μGy and 0.079 μGy for CBCT3, for every one meter away from the x-ray gantry. Therefore, at certain distances from the central x-ray, the scattered radiation was below the critical 1mGy. Consequently, an operator could stay inside the room accompanying the patient being scanned, if necessary.

Fracture and failure performance of foamed concrete materials were conducted using three methods, i.e., inverse analysis, digital image correlation (DIC) and finite element modelling (FEM) from tested normalized notched beams under three-point bending. From this study, several characteristics both experimental and FEM are discussed. However inverse analysis is only well applicable for series GF-30. The bilinear softening of the testing beam was estimated to identify fracture energy (GF), critical crack length (ac) and elastic modulus (E) with values of 0.015 N/mm, 54.5 mm, and 13 GPa, respectively. Additionally, fracture toughness was calculated by adopting double-K (initiation fracture of 6.907 MPa.mm0.5, unstable fracture of 23.186 MPa.mm0.5 and cohesive fracture of 16.278 MPa.mm0.5). Two-dimensional FEA Modelling of fracture was carried out using a Traction Separation Law (TSL), incorporating extended finite element method (XFEM) and cohesive zone (CZM) techniques. A sensitivity study was carried out, global mesh size of two and damage stabilization cohesive with the value of 1 × 10-5 showed good convergence and were used in other models. Furthermore, by comparing experimental observation using DIC, reliability FEM was validated and showed good acceptance to simulating the crack propagation.

Laser therapy devices (LTDs) operating with near-infrared laser light are increasingly being used in sports medicine. For several reasons the users cannot evaluate whether or not such devices emit laser beams according to the specifications provided by the manufacturer and the settings of the device. In this study the laser beams from two different LTDs that can be used in sports medicine were thoroughly characterized by measuring the emitted power, pulse shapes and lengths, and spatial intensity distributions using professional, high-fidelity laser measurement technology. This was repeated for three units of each LDT independently to distinguish problems of individual units from potential intrinsic instrument design errors. The laser beams from the units of one LTD agreed with the settings at the device, with the measured average power for these units being within 3.3% of the set power. In contrast, the laser beams from the units of the other LTD showed large deviations between the settings and the actual emitted light. This device came with three laser diodes that could be used independently and simultaneously. The average power differed greatly between the units as well as between the laser diodes within each unit. Some laser diodes emitted essentially no light, which could lead to a lack of treatment of patients. Other laser diodes emitted much more power than set at the device (up to 230%) that could result in skin irritations or burnings of patients. These findings indicate a need for better standardization and consistency of therapeutic laser light sources.

Adaption of laser communication terminals to airborne and lean-satellite platforms is now a vogue, made possible due to the progressing advancements in lightweight components and compactness of onboard electro-optical transceivers and control systems. This enables highly secured and superior data-transmission rates beyond multiple Gigabit/second on CubeSats and drones compared to Megabit/second rates offered by similar radio-transceivers form factors. However, laser-transmission links require a very stringent beam-pointing stability because they are easily perturbed by attitude variations and micro-vibrations generated by the host platform’s propulsion system or other mechanically active subsystems in proximity with the transmitter’s optical head. Severe line-of-sight jitter causes the downlink laser beam to drift from the targeted receiving system’s field-of-view, inducing pointing errors, increasing signal outage probability and information loss. We experimentally examine the platform jitter generated by the propellers of an hexacopter drone during ground operation and the attitude-control unit’s reaction wheels in a 6U CubeSat structure. We determined the vibration spectrum unique to these platforms and accordingly prescribe requirements for applicable optical fine pointing and disturbance isolation or suppression systems needed to achieve a high-fidelity laser-communication link.

Compared with liquid crystal clad waveguide, MEMS mirror has some merits, such as high-er-transmissivity, lager-angle of scanning, faster scanning speed and so on. Furthermore, MEMS mirror arrays perform more superior than MEMS mirror when they steer laser beam, which make MEMS arrays much more suitable to be used in devising compact Lidar. Before assembling a Lidar with MEMS arrays, the optical intensity and distributions of the laser diffracted by MEMS arrays should be analyzed, but few published papers about this issue are available so far, this paper will focus on this issue about MEMS arrays. Firstly, the complex amplitudes of laser which is diffracted by 1-D and 2-D arrays are presented, respectively. Then the optical intensity and distributions on the observation plane are presented. Finally, the simulation diagrams of these distributions are shown, and the correctness of the results is indirectly verified by Young’s dou-ble-slit experiment. The results gotten in this letter are essential to design a compacted Lidar based on MEMS arrays.

We report on the successful preparation of wet dressings hydrogels based on Chitosan-Poly(N-Vinyl-Pyrrolidone)-Poly(ethylene glycol)-Poly(acrylic acid) and Poly(ethylene oxide) by e-beam cross-linking in weakly acidic media, to be used for rapid healing and pain release of infected skin wounds. The structure and compositions of hydrogels investigated according to sol-gel and swelling studies, network parameters, as well as FTIR and XPS analyses showed the efficient interaction of the hydrogel components upon irradiation, maintaining the bonding environment while the cross-linking degree increasing with the irradiation dose and the formation of a structure with the mesh size in the range 11-67 nm. Hydrogels with gel fraction above 85% and the best-swelling properties in different pH solutions were obtained for hydrogels produced with 15 kGy. The hydrogels are stable in the simulated physiological condition of an infected wound and show appropriate moisture retention capability and the water vapor transmission rate up to 272.67 g m-2 day-1, to ensure fast healing. The hydrogels proved to have a significant loading capacity of ibuprofen (IBU), being able to incorporate a therapeutic dose for the treatment of severe pains. Simultaneously, IBU was released up to 25% in the first 2h, having a release maximum after 8h.

In-situ nanoindentation experiment has been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiment in characterizing nonlinear material properties of 3D integrated microelectronic devices with through-silicon-vias (TSVs). The elastic, plastic, and interfacial fracture behavior of the copper via and matrix-via interface have been characterized using small scale specimens prepared with focused-ion-beam (FIB) and nanoindentation experiment. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7 to 83.7 degrees. The mixed-mode fracture strengths were extracted using the linear elastic fracture mechanics (LEFM) analysis and a fracture criterion was obtained by fitting the extracted data with the power-law function. The vectorial interfacial strength and toughness were found to be independent with mode-mix.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

Measuring sound pressure is a complex and tedious task in industrial environments. Classical methods can be costly, inaccurate, and potentially dangerous for workers. Integrating robotics and computer vision into acoustic measurement processes offers an innovative solution to these problems. This paper uses a Doosan Robotic Vision System to investigate an innovative automatic acoustic sound pressure measurement solution. The Doosan robot, equipped with a scanning camera and microphone, captures acoustic data and produces a map of the machine’s acoustic radiation using computer vision algorithms. The measurement technique is accurate, efficient, and safe for workers. It can also be used for continuous monitoring of the industrial acoustic environment. The developed measurement method offers a promising way to automate acoustic measurement, which can be performed faster and with better accuracy to help industries improve their product sound quality and reduce noise levels. The method was compared to analytical predictions. A 3D acoustic mapping was conducted to visualize the spatial distribution of sound sources within the environment. The experimental results show a good correlation with the theory.

This research explores the depolymerization of waste polymethyl methacrylate (PMMAW) from dental material in fixed-bed semi-batch reactors, focusing on three production scales: laboratory, technical, and pilot. The study investigates the thermal degradation mechanism and kinetics of PMMAW through thermogravimetric (TG) and differential scanning calorimetry (DSC) analyses, revealing a two-step degradation process. The heat flow during PMMAW decomposition is measured by DSC, providing essential parameters for designing pyrolysis processes. The results demonstrate the potential of DSC for energetic analysis and process design, with attention to standardization challenges. Material balance analysis across the production scales reveals a temperature gradient across the fixed bed negatively impacting liquid yield and methyl methacrylate (MMA) concentration. Reactor load and power load variables are introduced, demonstrating decreased temperature with increased process scale. The study identifies the influence of temperature on MMA concentration in the liquid fraction, emphasizing the importance of controlling temperature for efficient depolymerization. Furthermore, the research highlights the formation of aromatic hydrocarbons from the remaining char, indicating a shift in liquid composition during the depolymerization process. The study concludes that lower temperatures below 450 °C favor liquid fractions rich in MMA, suggesting the benefits of lower temperatures and slower heating rates in semi-batch depolymerization. The findings contribute to a novel approach in analyzing pyrolysis processes, emphasizing reactor design and economic considerations for recycling viability. Future research aims to refine and standardize the analysis and design protocols for pyrolysis and similar processes.

This paper is a follow-up to a previous study that was conducted in a research forest and identified the optimal method for Diameter at Breast Height (DBH) estimation as a circular scanning and fitting ellipses to 4cm stem cross-sections at breast height. The aim of this study was to determine whether the identified method is applicable to natural boreal forests as well. The iPad Pro LiDAR scanner was used to acquire point clouds for 15 sites representing a range of natural boreal forest conditions in Ontario, Canada, and estimate DBH. The secondary objective was to determine if tested stand (Species composition, age, density, understory) or tree (Species, DBH) factors affected the accuracy of estimated DBH. Overall, estimated DBH values were within 1cm of actual DBH values for 78 of 133 measured trees (59%). An RMSE of 1.5cm (8.6%) was achieved. Stand age had a large effect (&gt;0.15) on the accuracy of estimated DBH values, while density, understory, and DBH had moderate effects (0.05-0.14). No trend was identified between accuracy and stand age. Accuracy improved as understory density decreased and as tree DBH increased. Inertial Measurement Unit (IMU) and positional accuracy errors with the iPad Pro scanner limit the feasibility of using this device for forest inventories.