Deformation monitoring is beneficial to ensure the service safety of long tunnel. An three-direction (vertical, transverse and axial) deformation estimation method using long-gauge fiber Bragg grating (FBG) sensing technology is proposed and applied to a long tunnel by integrating mechanical analysis and field monitoring during the service state. The key issues of the proposed method for identifying the three-direction deformation are discussed, such as establishing the separation model of coupling strain on cross section, deriving the theory of deformation identification in three directions, and determining the sensor layout of the long tunnel. A major advantage of the proposed method is that the three-direction deformation of the tunnel can be monitored in real time using distributed long-gauge strain sensors. The numerical analysis and field test results verify the feasibility of the proposed method.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

Isometric exercises for physiotherapeutic rehabilitation are often prescribed, with little quantification of the load being prescribed. This article aimed to provide a framework and practical examples of how the physiotherapist may take a more quantitative evidence-based approach to isometric assessment, monitoring, and exercise prescription of knee osteoarthritis, by integrating a strain gauge into their practice. Strength measures to monitor were discussed. A series of fourteen studies were reviewed, with the intent of identifying isometric exercises that had been utilized in the rehabilitation of knee osteoarthritis. Of the fourteen studies, the three most identified isometric exercises were seated knee extension, knee flexion, and the supine straight leg raise. The integration of strain gauge technology with these exercises provided the focus of the remainder of the article.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Prestress loss evaluation in prestressed strand is essential for prestressed structures. However, the sensors installed outside the duct can only measure the total prestress loss. The sensors attached on strand inside the duct also have several problems, such as inadequate durability in an aggressive environment, vulnerable damage at tensioning and so on. This paper proposes a new installation method for long-gauge fiber Bragg grating (LFBG) sensor to prevent accidental damage. Then the itemized prestress losses were determined in each stage of the pre-tensioning and post-tensioning according to the LFBG measurements. We verified the applicability of the LFBG sensors for prestress monitoring and the accuracy of the proposed prestress loss calculation method during pre-tensioning and post-tensioning. In the pre-tensioning case, the calculated prestress losses had less deviation from the true losses than those obtained from foil-strain gauges, and the durability of the LFBG sensors was better than foil-strain gauges, whereas in post-tensioning case, the calculated prestress losses were close to those derived from theoretical predictions. Finally, we monitored prestress variation in the strand for 90 days. The itemized prestress losses at each stages of post-tensioning were obtained by the proposed calculation method to show the prospect of the LFBG sensors in practical evaluation.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

This chapter aims to construct a relatively complete, universal, and highly reliable road surface state monitoring and perception system through the research of the A1 contact road reconstruction project of an international airport (hereinafter referred to as the “airport”). The system design is based on on-the-spot investigation, theoretical analysis, and engineering practice, using vibrating string type and resistive strain sensors as sensing means, real-time high-frequency signal acquisition technology as the guide, 4G router for wireless communication technology as the media, and storage technology for monitoring system based on server storage terminals. In combination with engineering background, aircraft motion state, main landing gear configuration, sensor selection and evaluation, and other major factors, the actual monitoring information needs of the plane are fully taken into account, as well as the difference in sensor information types, and the system design is carried out by stratification and classification.

We have successfully measured amyloid beta (Aβ) (1-40) protein added in human serum by a NiCr strain gauge cantilever biosensor immobilized with liposomes incorporating cholesterol. Importantly, we investigated the effect of incorporation of cholesterol in the liposome in order to suppress the interaction between the liposome and many different proteins included in human serum. It was revealed that incorporating cholesterol suppresses the interaction between the proteins other than Aβ in human serum and the liposome. Finally, we detected Aβ(1-40) in human serum with typical chronological behaviors due to Aβ aggregation and fibrillization. Furthermore, as a digital low-pass filtering procedure could reduce external noises, the cantilever sensor immobilized with liposome incorporating cholesterol can detect low-concentrated Aβ in human serum.

Monitoring of structures is one of the engineering challenges of the 21st century. At the same time, as a result of changes in the conditions of use, design errors, many building structures require strengthening. The article presents research on the development of the external strengthening carbon fiber textile with an option of self-sensing. The idea is based on the pattern of resistive strain gauge, where thread is provided in a zig-zag of parallel lines. Already the first laboratory tests showed the high efficiency of the system in the measurement of strains, but also revealed the sensitivity of measurement to environmental conditions. The article presents studies on the influence of temperature and humidity on the measurement. To separate those effects, resistance changes were tested on unloaded concrete and wooden samples. The models were placed in a climatic chamber and the daily cycle of temperature and humidity changes was simulated. The results of the research confirm preliminary observations. Resistivity growths with the temperature. This effect is more visible on concrete samples, presumably due to its greater natural humidity. The strain measurement with carbon fibers is very sensitive to temperature changes and application of this method in practice requires compensation.

Tuning nonlinearity of the laser is the main source which will deteriorate the spatial resolution in optical frequency domain reflectometry system. We develop methods for tuning nonlinearity correction in the OFDR system from the aspects of data acquisition and also the posting-processing. A zero-crossing detection scheme is researched and implemented by a customized circuit. Equal-spacing frequency sampling is therefore achieved in real-time. The maximum sensing distance can reach to the same length of the auxiliary interferometer. The zero-crossing detection for the beating frequency of 20MHz is achieved. Then, a nonlinearity correction method based on the self-reference method is proposed. The auxiliary interferometer is no longer necessary in this scheme. The tuning information of the laser is extracted by a strong reflectivity point at the end of the sensing arm in the main interferometer. The tuning information can then be used to resample the raw signal and the nonlinearity correction can be achieved. The spatial resolution test and the distributed sensing experiments are both performed based on this nonlinearity correction method. The results validated the feasibility of the proposed method. The method reduces the hardware and data burden for the system and has a potential value on the system integration and miniaturization.

The investigation on the issue of damage diagnosis based on strain modal parameters is conducted in this paper using simply supported wooden Beams as the study's object. First, ABAQUS is utilized to create finite element models of intact wooden beams as well as wooden beams with varying degrees of damage and perform modal analyses on them. Next, damage identification studies are conducted on the wooden beam structure using various strain modal parameters (strain mode strain modal difference, strain modal curvature difference), the timber beam damage identification test then yields the modal parameters of timber beams under various damage situations, and the test findings are contrasted with those of the numerical simulation. The outcomes demonstrate that the damage identification of the test data using the three types of damage identification indexes is consistent with the results of the numerical simulation; the three types of damage identification indexes can locate the damage to timber beams, but the identification effect of the indexes is different, the best-recognized metric is the strain mode curvature difference; the next best is the strain mode difference, and the worst is the strain modes. The study's findings can serve as a guide for future damage detection on wood beams.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

1) Background: Ultrasound-based strain imaging is now available in several ultrasound (US) scanners. Strain ratio (SR) can be used to quantify strain recorded simultaneously in two different user-selected areas, ideally exposed to the same amount of stress. The aim of this study was to evaluate SR variability when assessed in an in-vitro setup with a tissue-mimicking phantom, on resected tissue samples and in live tissue scanning with endoscopic applications. 2) Material and methods: Retrospective analysis of SR for quantification of elastic contrasts in a tissue-mimicking phantom containing four homogenous inclusions, in 38 resected bowel wall lesions and in 48 focal pancreatic lesions examined in vivo. Median SR and the inter-quartile range (IQR) was calculated on all external and endoscopic US-applications. The IQR/median provides a measure of the SR variability focusing on the two percentiles of the data closest to the median value. 3) Results: The overall variability of SR was lowest in a tissue-mimicking phantom (mean QR/median SR: 0.07). In resected bowel wall lesions representing adenomas, adenocarcinomas or Crohn lesions, the variability increased (mean IQR/Median: 0.62). During an endoscopic examination of focal pancreatic lesions in vivo, the variability increased further (mean IQR/Median: 2.04). 4) Conclusion: SR variability increased when assessed on different targets with growing heterogeneity and biological variability as one moved from homogeneous media to live tissues and endoscopic application. This may indicate a limitation for the accuracy SR evaluation in clinical applications.

The paper presents an extensometer designed to measure two mechanical strains at the same time—one from tensile load and the other from torsion load. Strain transducers provide different electric signals, which, after calibration, lead to the simultaneous measurement of linear (ε) and angular (γ) strains. Each of these two signals depends on the measured process and is not influenced by the other strain process. This extensometer is designed to be easily mounted on the sample with only two mounting points and can be used to measure the combined cyclical fatigue of tensile and torsional loadings. This extensometer has two bars—one rigid, reported at the resulting stress points, and one elastic and deformable. The elastic deformable bar has two beams with different orientations. When the sample is deformed, both beams are loaded by two bending moments (perpendicular to each other and both perpendicular on the longitudinal axis of the bars).

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

When different strain hardening and strain rate sensitive materials are used for scaled model and prototype, the traditional pure geometrical similarity laws of solid mechanics will fail. Although correcting the basic scaling factors of velocity, density and geometry have been developed to compensate for the material distortion in recent non-geometric scaling works, it is difficult to be widely used because of its inherent indirect (depending on the structural strain and strain rate responses) and inexact (having significant prediction errors for prototype) defects. In this paper, a framework of material similarity, based on the new suggested material dimensionless numbers and the ‘Material number vs. strain/strain-rate’ function curves, are further developed, which represents the objective requirement of similarity theory for the basic mechanical properties of materials. It is demonstrated what is similitude materials of solid mechanics and how to use the best similitude materials to overcome the non-scalabilities of materials for identical or different materials. The direct and exact solution of the basic correction factors is further obtained and therefore overcomes the previous inherent indirect and inexact defects radically. Based on the similarity evaluation of different materials of the classical constitutive models, the impacted structures of circular plate and crooked plate with strain hardening and strain rate sensitive materials are verified numerically. The results show the completely different materials can be exact similitude for various structural behaviors (strain, strain rate, stress and displacement) of time and space fields after using the best similitude materials; and the basic correction factors do not depend on the structural strain and strain rate responses. As a contrast, when the non-similitude materials are used, the similarity results are very sensitive to the selection of strain/strain-rate and often leads to failed predictions. In addition, for the material elastic and temperature effects, the proposed method is also discussed to be valid.

Many (if not a very large number) of metals and alloys evince substantial softening with torsion deformation to strains not usually achievable in tension. Of course, softening has long been observed by discontinuous dynamic recrystallization (DDRX) but this paper will discuss cases where softening is associated by texture development with large-strain deformation that is not reliant on changes in the dislocation hardening. This paper reviews the work of the current authors on FCC metals and alloys in this area and extends to a new discussion of BCC and HCP cases.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double <100> and <111> fiber and a unique component of (001)<110>, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

One of the major limitations of the current 3D-concrete-printing technology is incorporation of reinforcement. Furthermore, there is a need to decrease the ecological footprint of printable concrete. As a possible solution for these challenges, this paper presents a 3D-printable strain-hardening geopolymer composite (3DP-SHGC) that shows pseudo-ductile behaviour under direct tension. The developed 3DP-SHGC is composed of one-part (just-add-water) geopolymer binder made of slag (GGBFS), fly ash (FA) and solid activator. The one-part geopolymer binder eliminates the need for elevated temperature curing and handling of corrosive alkaline liquids. At first, an optimum matrix was identified by studying the effects of FA to GGBFS ratio on the rheological properties and compressive strength. Subsequently the optimum matrix was reinforced by PVA fibres to make the 3DP-SHGC, which printing performance and rheological properties were evaluated. In addition, the influences of curing temperature on the compressive, flexural and tensile performances of the printed specimens were also investigated. The results were compared with those obtained for the mould-cast specimens. The 3DP-SHGC exhibited superior flexural performance, higher tensile strength, and comparable tensile strain capacity to the mould-cast counterpart. Further, the curing temperature had influence on the mechanical properties of both 3D-printed and mould-cast SHGCs. The underlying reasons for the differences are discussed.

Current progress in the prediction of mechanical behavior of solids requires understanding of spatiotemporal complexity of plastic flow caused by self-organization of crystal defects. It may be particularly important in hexagonal materials because of their strong anisotropy and combination of different mechanisms of plasticity, such as dislocation glide and twinning. These materials often display complex behavior even on the macroscopic scale of deformation curves, e.g., a peculiar three-stage elastoplastic transition, the origin of which is a matter of debates. The present work is devoted to a multiscale study of plastic flow in α-Ti, based on simultaneous recording of deformation curves, 1D local strain field, and acoustic emission (AE). It is found that the average AE activity also reveals three-stage behavior, but in a qualitatively different way depending on the crystallographic orientation of the sample axis. On the finer scale, the statistical analysis of AE events and local strain rates testifies to an avalanche-like character of dislocation processes, reflected in power-law probability distribution functions. The results are discussed from the viewpoint of collective dislocation dynamics and are confronted to predictions of a recent micromechanical model of Ti strain hardening.

Tomato leaf curl disease (TLCD) is the most common viral disease in the tomato plant. It is caused by begomoviruses, which are viruses that cause plant development to be slowed. Many of the traditional disease management methods are still in use. They are, however, ineffective and out of date. Modern biotechnology is being used to detect illness in tomato plants as early as possible, thus reducing damage to the plants. Through genetic engineering, the spread of viruses may be controlled or prevented entirely. Here reviewed many methods for decreasing or eliminating the viral influence on crop growth through biotechnology and genomics. We also investigated the possibility of genetic engineering to reduce or remove the virus TLCD impact on tomato crop development.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

Introduction: Left ventricular dysfunction in an independent predictor of mortality in Chagas disease. Global longitudinal strain (GLS) is an emerging echocardiographic modality with possible incremental value in early detection of cardiac involvement. Objective: Compare left ventricular function with multiple echocardiographic parameters between patients with the indeterminate and chronic forms of Chagas and perform a literature review. Methods: In this observational study, 11 patients with a confirmed diagnosis of Chagas disease were evaluated. Individuals were distributed as follows: 5 with the indeterminate and 6 with the chronic forms. Conventional echocardiographic evaluation was followed by GLS measurement. Results: The mean left ventricle ejection fraction LVEF was 33 ± 2.88 and the mean GLS of the left ventricle was - 10.76 ± 2.20 in the chronic form as compared to 57.80 ± 6.49 and - 17.34 ± 3.82, respectively in the indeterminate group. Contractility was reduced in segments of the inferior, inferoseptal and anteroseptal walls in both groups. Conclusion: Analysis of longitudinal strain in the indeterminate form has potential incremental value to the conventional analysis of ejection fraction when compared to patients with chronic Chagas cardiomyopathy, especially with individual segmental analysis but the impact and clinical significance of these techniques is still unknown.

Introduction: The disease caused by Coronavirus-2019 (COVID-19) was initially described in December 2019. Severe acute respiratory syndrome type 2 (Sars-Cov-2) is responsible for an important multisystem inflammatory spectrum. Cardiovascular conditions have been reported with an estimated frequency of 8-28%. In this context, transthoracic echocardiography associated with the analysis of the two-dimensional Global Longitudinal Strain (GLS) of the left ventricle derived from Speckle Tracking emerges as a promising modality. Objective: This study aims to evaluate the applicability of GLS and segmental deformity assessment in detecting subclinical myocardial dysfunction in patients that recovered from COVID-19 infection. Methods: The observational study involved 18 patients (mean age 52 years) with recent evidence of COVID-19 infection that underwent detailed echocardiographic evaluation with GLS, and cardiac magnetic resonance (CMR) according to segmental assessment results. The degree of correlation between the methods was analyzed and a systematic literature review was also conducted. Results: The mean left ventricular ejection fraction (LVEF) was 57.50 ± 9.98%. Only 16.6% of patients had reduced LVEF. The average GLS was – 18.70 ± 3.54% and in 44% of cases only one myocardial segment was affected, particularly the inferolateral basal. CMR revealed inflammatory cardiomyopathy. Discussion: Subclinical myocardial involvement is associated with major adverse cardiac events. Literature review supports the use of GLS for detecting early cardiac involvement. Conclusion: Speckle-tracking echocardiography has been shown to have clinical utility in a variety of settings and to offer superior prognostic value with a potential to enhance subclinical detection of myocardial changes in patients after COVID-19 infection.

MgB2 is a hexagonal superconducting material, and its simple composition has led to the development of low-cost practical wires. However, the problem is that the strain characteristics of filaments are inferior to those of other practical wires, but there have been no strain measurements using diffraction method. The reason for this is presumably that it is a little too thick for synchrotron radiation measurements, and the large absorption cross section of the included boron-10 makes it difficult to obtain elastic scattering for neutron measurements. We prepared a wire substituted with boron-11, an isotope with small neutron absorption cross section, and attempted to measure its strain under tensile loading using pulsed neutron.

We have developed a self-consistent model for predicting velocity of 1/2[111] screw dislocation in binary iron--carbon alloys gliding by a high-temperature Peierls mechanism. The methodology of modelling includes: (i) Kinetic Monte-Carlo (kMC) simulation of carbon segregation in dislocation core and determination the total carbon occupancy of the core binding sites; (ii) Determination of kink-pair formation enthalpy of a screw dislocation in iron---carbon alloy; (iii) KMC simulation of carbon drag and determination of maximal dislocation velocity at which the atmosphere of carbon atoms can follow a moving screw dislocation; (iv) Self consistent calculation of average velocity of screw dislocation in binary iron--carbon alloys gliding by a high-temperature kink-pair mechanism under constant strain rate. We conduct a quantitative analysis of the conditions of stress and temperature at which screw dislocation glide in iron--carbon alloy is accomplished by a high-temperature kink-pair mechanism. We estimate the dislocation's velocity at which screw dislocation brakes away from the carbon cloud and thermally-activated smooth dislocation propagation is interrupted by sporadic bursts controlled by athermal dislocation activity.

Bridges enable communications and transportation of goods nationally and internationally, underpinning economic and social activities, thus they are pylons of our prosperity and mobility. Bridges worldwide are constantly subjected to physical wear, ageing, deterioration, hazards, environmental influences, and increased loading. Loss of performance and functionality of bridge structures would have a crucial impact on overall infrastructural resilience and would cause significant negative economic and social consequences. Monitoring their behaviour for different loading conditions relies on accurate estimations of the stress-strain state of various critical components and remaining capacities. These activities are of high importance for better planning and lifespan prolongation, that is the extension of their service life and prevention of unforeseen collapses, in line with sustainability principles of well-informed maintenance. In many cases, access to the structure is limited or even impossible, which causes the need for the deployment of remote and contactless methods. One such innovative technique, which has recently attracted attention in scientific and practical applications is the digital image correlation (DIC). DIC is a contactless approach applicable for obtaining the full field of strains and deformations of full-scale real structures. Although the DIC approach has been widely used in world engineering practice for monitoring bridges and has proved to be a reliable and accurate method, there is a lack of systematic integral review on previous practical applications, revealing limitations and perspectives. This is the main motivation and novelty of this study, which will describe selected case studies, in which DIC was used on real full-scale bridge structures and propose improvements for the method.

This study investigates by hybrid approach of classical calculations and numerical explicit FEM simulation the strain rate sensitive hardening of Polypropylene Sabic 83MF10 under dynamic tension loads. The Cowper-Symonds model is employed to characterize the non-linear increase in yield strength with strain rate, within the range of 0,01 to 1 [1⁄s]. For lower strain rates, a drastic decrease in yield strength is observed, suggesting the significant influence of creep and relaxation phenomena. The study proposes further research incorporating viscoelastic properties for a more comprehensive material model. Additionally, the study observes a disproportionate increase in yield strength for samples with smaller radius, indicating a dependency on triaxiality which suggests further research on the Drucker-Prager model for this material. The study concludes by recommending a broader range of input parameters for future studies, including the Johnson-Cook model and comparison of tensile test results with compression test results.

This article explores the emerging concept of atrial myopathy (AM) and its potential role as a risk factor for stroke and dementia, both independently and in association with atrial fibrillation (AF). AM refers to structural and functional abnormalities of the atria, potentially causing blood clots formation and their subsequent embolization even in patients without AF. Echocardiography, particularly Left Atrial (LA) strain analysis, is a promising non-invasive tool for AM evaluation and might offer additional risk stratification beyond the established CHADS2-VASc score, potentially impacting anticoagulation decisions. By understanding AM and utilizing advanced imaging techniques like LA strain, clinicians can achieve a more comprehensive understanding of thromboembolic risk in specific patient groups. Integrating LA strain analysis into routine clinical practice holds promise for improved patient management and targeted therapies, allowing for better risk stratification in AF patients. However, standardized definitions and diagnostic criteria for AM are essential for consistent evaluation and research. Further studies are needed to explore the efficacy and safety of anticoagulation in AM patients without AF.

Background: Evaluation of left ventricular(LV) functions in patients with idiopathic premature ventricular contraction(PVC) with preserved LV Ejection Fraction(LVEF), especially in the subclinical stage, may be of great importance in terms of directing early treatment. Methods: A total of 122 patients, retrospectively recruited, were divided into three groups according to PVC burden: Group 1; 5%PVC<10%, Group 2; 10%PVC<15%, and Group 3; 15% PVC. Transthoracic echocardiography(TTE) was performed to evaluate LV parameters. Results: LV-GLS was found to be significantly lower in groups 2 and 3 with high PVC burden (18.89 ± 1.4, 17.55 ± 2.1, 16.26 ± 1.3; p<0.001 respectively). Correlation analysis revealed a positive and significant correlation between PVC burden with deterioration in LV-GLS (r:0.536; p<0.001). In addition, PVC burden was found to be an independent predictor of LV-GLS deterioration in multiple linear regression analysis(:0.525, p<0.001). The ROC curve analysis demonstrated that a PVC burden cut-off value of 8.4% was associated with a LV-GLS deterioration greater than -18, with a specificity of 75.4% and a sensitivity of 75.4% (AUC: 0.81 [0.73-0.88] 95% CI; p<0.001). Conclusions: PVC burden was an independent predictor of deterioration in LV-GLS. In the presence of subclinical LV injury associated with PVC burden, early catheter ablation strategies may be therapeutically beneficial.

Background and Objectives: Similar to diabetes, the presence of left ventricular (LV) diastolic function (DD) has been reported in various studies which were conducted with people with a diagnosis of impaired fasting blood glucose (FBG). The study aimed to examine the effects of fasting blood glucose (FBG) levels on left atrial strain (LAS) estimated by two-dimensional echocardiography speckle tracking analyses in patients without known diabetes. Material and Methods: The study included 148 participants (74 female and 74 male) without a history of diabetes mellitus or chronic disease. The patients were divided into two groups as follows: individuals with FBG <100 mg/dl and those with FBG between 100-125 mg/dl after at least 8 hours of overnight fasting and according to these FBG levels STE measures were compared. Results: There was a significant decrease in the LA reservoir (52.3±15 vs. 44.5±10.7; p=0.001) and conduit strain (36.9±11.7 vs. 28.4±9.7; p=0.001) in the impaired FBG group. When the STE findings of both ventricles were compared, no significant difference was observed between the groups in right and LV strain imaging. Conclusion: In the earliest stage of LVDD, changes in atrial functional parameters become particularly evident. Echocardiographic analyses of these parameters can help to diagnose and determine the degree of LVDD while the morphological parameters are still normal. The addition of LAS imaging to the routine TTE study in patients with impaired FBG but without a DM diagnosis may be helpful in demonstrating subclinical LVDD or identifying patients at risk for LVDD in this patient group.

This work describes a resonance Raman study performed in domes of monolayer MoS2 using 23 different laser excitation energies covering the visible and near-infrared (NIR) ranges. The multiple-excitation results allowed us to investigate the exciton-phonon interactions of different phonons (A1’, E’ and LA) with different electronic and excitonic optical transitions in biaxially strained monolayer MoS2. The analysis of the intensities of the two first-order peaks, A1’ and E’, and the double-resonance 2LA Raman band as a function of the laser excitation furnished the values of the energies of the indirect gap and the excitonic transitions in the strained MoS2 domes. It was noticed that the out-of-plane A1’ phonon mode is significantly enhanced only by the indirect gap I and the C exciton, whereas the in-plane E’ mode is only enhanced by the C exciton of MoS2 dome, revealing thus a weak interaction of these phonons with the A and B excitons in the strained MoS2 domes. On the other hand, the 2LA Raman band is significantly enhanced at the indirect gap I transition and by the A (or B) exciton, but not enhanced by the C exciton, showing thus that the LA edge-phonons that participate in the double resonance process in MoS2 have a weak interaction with the C exciton.

Magnesium (Mg) alloy is a widely used lightweight metal structural material due to its high specific strength and stiffness, excellent damping performance, and recyclability. Wrought Mg alloys are widely favored in fields such as aerospace, transportation, and biomedical stents. However, most wrought Mg alloys with a hexagonal close-packed (HCP) crystal structure lack sufficient independent slip systems to meet the von Mises criterion for uniform plastic deformation at room temperature. This can result in the formation of strong basal texture during plastic deformation and poor room temperature plastic forming ability. Improving the room temperature forming performance is a crucial challenge that must be addressed to broaden the application of Mg alloy sheets. Our research group has comprehensively summarized significant work and latest research progress in improving the room temperature forming of Mg alloy sheets via extrusion technology in recent years. Specifically, we have developed a new type of asymmetric extrusion technology that combines material structure evolution, mechanical property, and forming behavior analysis. We have elucidated the extrusion process characteristics, texture control mechanism, and forming properties of Mg alloy sheets through plastic deformation mechanisms, mold design, and finite element numerical simulation. Our findings provide a novel extrusion technology for the fabrication of highly formable Mg alloy sheets, which can be utilized in various applications.

Copper toxicity has been a selective pressure on the sea-ice bacteria due to its widespread occur-rence in Antarctica. Here, with a combined biochemical and metabolomic approach, the Cu2+ ad-aptation mechanisms of Antarctic bacteria were analyzed. Heavy metal resistance pattern of Pb2+ > Cu2+ > Cd2+ > Hg2+ > Zn2+ was observed. Copper treatment did increase the activity of antioxidants and enzymes, maintaining cellular redox state balance and normal cell division and growth. Metabolomics analysis demonstrated that fatty acids, amino acids, and carbohydrates played dominant roles in copper stress adaptation. The results indicated that the adaptation mechanisms of strain O5 to copper stress included protein synthesis and repair, accumulation of organic per-meable substances, up-regulation of energy metabolism, and formation of fatty acids. This study increases the resistance mechanism understanding of Antarctic strains to heavy metals in extreme environments.

Quantitative dynamic strain measurements of the ground would be useful for engineering scale problems such as monitoring for natural hazards, soil-structure interaction studies and non-invasive site investigation using full waveform inversion (FWI). Distributed Acoustic Sensing (DAS), a promising technology for these purposes, needs to be better understood in terms of its directional sensitivity, spatial position, and amplitude for application to engineering-scale problems. This study investigates whether the physical measurements made using DAS are consistent with the theoretical reception patterns and experimental measurements of ground strain made by geophones. Results show that DAS and geophone measurements are consistent in both phase and amplitude for broadband (10s of Hz), high amplitude (10s of microstrain) and complex wavefields originating from different positions around the array when: (1) the DAS channels and geophone locations are properly aligned, (2) the DAS cable provides good deformation coupling to the internal optical fiber, (3) the cable is coupled to the ground through direct burial and compaction, and (4) laser phase noise is mitigated in the DAS measurements. The theoretical relationship between DAS-measured and point-wise strain for vertical and horizontal active sources is introduced using 3D elastic finite-difference simulations. The implications of using DAS strain measurements are discussed including directionality and magnitude differences between the actual and DAS-measured strain fields. A method for spatially aligning the DAS channels with the geophone locations at tolerances less than the spatial resolution of the DAS system is proposed.

The effects of an external strain tensor on the electrical resistivity of a manganite granular system are investigated using a simple approach describing the induced deformation in terms of the tilt angle between adjacent grains. The results obtained assuming the resistivity of each grain as given by a metallic part, coming from the inner grain, and a surface related tunnel contribution, allow to estimate appreciable resistivity variations even in the case of small deformation angles.

The study presents the effect of annealing process parameters on the microstructure, hardness and strain hardening coefficients i.e., the strength coefficient c and the strain hardening exponent n, of 42CrMo4 steel. Seven selected annealing time-temperature schemes are examined for superior steel formability in cold metal forming conditions. The c and n coefficients are first determined in experimental upsetting of annealed samples and then used in FEM simulations of the upsetting process. The results demonstrate that the strain hardening coefficients (c and n) depend on the employed annealing scheme. Compared to the as-received sample, the annealing process reduces the true stress and effectively decrease the hardness of 42CrMo4 steel, improves microstructural spheroidization and, consequently, facilitates deformability of this material. The annealing schemes relying on heating the material to 750 °C and its subsequent slow cooling lead to the highest decrease in hardness ranging from 162 to 168HV. Results obtained with the SEM-EDS, LOM and XRD methods lead to the conclusion that the employed heat treatment schemes cause the initial ferritic-pearlitic microstructure to develop granular and semi-lamellar precipitation of cementite enriched with Mo and Cr in the ferrite matrix. In addition, the annealing process affects the growth of α-Fe grains. The highest cold hardening rate, and thus formability, is obtained for the annealing scheme producing the lowest hardness. The results of FEM simulations are positively validated by experimental results. Obtained results are crucial for further numerical simulations and experimental research connected with developing new cold metal forming methods for producing parts made of 42CrMo4 steel.

The paper describes preliminary studies on the influence of humidity on the electrical resistance of a textile sensor made of carbon fibers. The concept of the sensor refers to externally bonded fiber reinforcement commonly used to strengthen building structures. However, the zig-zag arrangement of carbon fiber tow allows measuring strains, as it is done in popular resistive strain gauges. The sensor tests proved its effectiveness in the measurement of strains, but also showed a high sensitivity to changes in the temperature and humidity which unfavorably affects the readings and their interpretation. The influence of these factors must be compensated. Due to the size of the sensor, there is not possible electrical compensation by the combining of several sensors into the half or full Wheatstone bridge circuit. Only mathematical compensation based on known humidity resistance functions is possible. The described research is the first step to develop such relations. The tests were carried out at temperatures of 10 °C, 20 °C and 30 °C, with changing the humidity in the range of 30-90%.

Metallic substrates and polymer adhesive in composite-metal joints have a relatively large coefficient of thermal expansion (CTE) mismatch, which is a barrier in the growing market of electric vehicles and their battery structures. It is reported that adding carbon nanotubes (CNTs) to the adhesive reduces the CTE of the CNT enhanced polymer adhesive multi-material system, therefore when used in adhesively bonded joints it would, theoretically, result in low CTE mismatch in the joint system. The current article presents the influence of two specific mass ratios of CNTs on the CTE of the enhanced polymer. It was observed that the addition of 1.0 wt% and 2.68 wt% of multi-walled CNTs (MWCNTs) decreased the CTE of the polymer adhesive from 7.5e-5 1/C (pristine level) to 5.87e-5 1/C and 4.43e-5 1/C, respectively by 22% and 41% reduction. The reduction in the CTE was predicted, theoretically, which showed that CTE should have been reduced to 3.6e-5 1/C (52% reduction) and 1.4e-5 1/C (81% reduction). This may be due to the fact that, Raman spectroscopy of the MWCNTs identified defects in the raw material, and scanning electron microscopy (SEM) identified agglomeration of MWCNTs on the surface and cross-section of the modified polymers.

Tuberculosis (TB), caused by Mycobacterium tuberculosis, is an infectious disease that seriously affects human life and health. Despite centuries of efforts to control it, in recent years the emergence of multidrug-resistant bacterial pathogens of M. tuberculosis due to various factors has exacerbated the disease, posing a serious threat to global health. Therefore, a new method to control M. tuberculosis is urgently needed. Phages, viruses that specifically infect bacteria, have emerged as potential biocontrol agents for bacterial pathogens due to their host specificity. In this study, a Mycobacterium phage, Henu3, was isolated from soil around a hospital. The particle morphology, biological characteristics, genomics and phylogeny of Henu3 were characterized. Additionally, to explore the balance between phage resistance and stress response, phage Henu3-resistant strains 0G10 and 2E1 were screened by sequence passage and bidirectional validation methods, which significantly improved the sensitivity of phage to antibiotics (cefotaxime and kanamycin). By whole genome resequencing of strains 0G10 and 2E1, 12 genes involved in cell wall synthesis, transporter-encoded genes, two-component regulatory proteins and transcriptional regulatory factor-encoded genes were found to have mutations. These results suggest that phage Henu3 has the potential to control M. tuberculosis pathogens, and phage Henu3 has the potential to be a new potential solution for the treatment of M. tuberculosis infection.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Numerous experimental and theoretical studies undertaken to determine the effective-stress coefficient for seismic velocities in rocks stem from the importance of this geomechanical parameter both for monitoring changes in rock saturation and pore pressure distribution in connection with reservoir production, and for overpressure prediction in reservoirs and formations from seismic data. The present work pursues a task to determine, in the framework of a low-frequency laboratory study, the dependence of the elastic moduli of n-decane saturated sandstone on the relationship between pore and confining pressures. The study was conducted on a sandstone sample with high quartz and notable clay content in the quasi-static regime, when the 100 ml tank filled with n-decane was directly connected to the pore space of the sample. The measurements were carried out at a seismic frequency of 2 Hz and strains, controlled by semiconductor strain gauges, not exceeding 10-6. The study was performed using a forced-oscillation laboratory apparatus utilizing stress-strain relationship. The dynamic elastic moduli have been measured in two sets of experiments: at constant pore pressures of 0, 1 and 5 MPa and differential pressure (defined as a difference between confining and pore pressures) varied from 3 to 19 MPa; and at а constant confining pressure of 20 MPa and pore pressure varied from 1 to 17 MP. It was shown that the elastic moduli obtained in the measurements are in good agreement with the Gassmann moduli calculated for the range of differential pressures used in our experiments, which corresponds to the effective-stress coefficient equal to unity.

This contribution was devoted to unveil the strain rate sensitivity (SRS) of G18NiCrMo3-6 cast steel in tension/compression asymmetry. For that purpose, detailed mechanical characterization tests were conducted providing a process window covering quasi-static and medium strain rate regimes (0.001, 0.1, 10 [ s¯¹]) in tension and compression states. By means of this experimental ef-fort, the SRS of the material could be extracted by a function of strain and strain rate which ena-bling to create a mathematical expression to easily be implemented as a state variable for constitu-tive material modeling. Finally, a pressure and rate dependent constitutive material model on the basis of Cocks'89 yield locus definition was created by a subroutine (UMAT) file and the material parameters were verified with respect to the experimental data. The UMAT file also takes into account the tension/compression asymmetry in yielding to handle the effect of porous media plas-ticity concept. The predictions of the proposed material model are quite in line with the experi-mental outputs.

This study aimed to investigate the diagnostic potential of circulating microRNAs (miRNAs) for detecting early myocardial fibrosis development in HFpEF patients. This observational study used a case-control research design. Peripheral blood samples were isolated from 25 HFpEF patients and 25 normal patients. They were measured for NTproBNP levels using ELISA, as well as MicroRNA-1, 21, and 29 levels using RT-PCR. All patients also underwent echocardiography for global longitudinal strain (GLS) to measure the myocardial fibrosis progression. Data were analyzed using SPSS 25.0. HFpEF patients had significantly higher GLS compared to the normal patients (-13±2.4% vs -19±3.2%; p &lt; 0.05), suggesting HFpEF patients tended to have myocardial fibrosis. HFpEF patients also had significantly higher microRNA-1 and microRNA-21 compared to the normal patients (p &lt; 0.05), but they had lower microRNA-1 (p &lt; 0.05). There was a positive correlation between microRNA-1 (r = 0.753; p &lt; 0.05) and microRNA-21 (r = 0.675; p &lt; 0.05) and an inverse correlation with microRNA-29 (r = -0.653; p &lt; 0.05) based on the GLS findings. By using a GLS cutoff of -15% for myocardial fibrosis, microRNA-1, microRNA-21, and microRNA-29 were found to be able to predict myocardial fibrosis based on GLS with a specificity of 78% and sensitivity of 75%. Increasing microRNA-1 and microRNA-21 followed by decreasing microRNA-29 in HFpEF patients suggest early myocardial fibrosis.

The rapid changes in the coronavirus genomes are creating new strains over time after the first variation found in Wuhan in 2019. SARS-CoV-2 (Severe Acute Respiratory Syndrome Coronavirus 2) genotypes need periodically undergo whole genome sequencing. Genome sequencing has been extremely helpful in combating this virus because so many diagnoses, treatments, and vaccinations have been developed against it. To achieve this, we generated 17 high-quality whole-genome sequence data from 48 SARS-CoV-2 genotypes of COVID-19 patients who tested positive by PCR in the Tashkent city of Uzbekistan. We identified nucleotide polymorphisms, including nonsynonymous (missense) and synonymous mutations in the coding regions of the sequenced sample genomes. All whole genome sequences were categorized by phylogenetic analysis into the G clade (or GK sub-clade). A total of 134 mutations were identified, consisting of 65 shared and 69 unique mutations. Collectively, nucleotide changes represented one frameshift mutation, one conservative and disruptive insertion deletion, four upstream region mutations, four downstream region mutations, 39 synonymous mutations, and 84 missense mutations. Furthermore, bioinformatics web tools were used to analyze amino acid changes in virus genomes. Several amino acid mutations were found, which were not found in previously published Delta strain sequences.

All over the world, externally bonded fiber-reinforced polymer systems used to strengthen concrete elements improve building sustainability. However, reports issued by the American Concrete Institute Committee 440 called for heavy scrutinizing before actual field implementation. The very limited number of proposed equations lacks reliability and accuracy. Thus, further investigation in this area is needed. In addition, machine learning techniques are being implemented successfully in developing strength models for complex problems. This study aims to provide a reliable machine learning model based on an experimental database. The proposed model was developed and validated against the experimental database and the very limited models in the literature. The model showed improved agreement with the experimental results compared to the previous models.

The International System of Units (SI) was adopted in 1960 as a universal measuring system to be used for all areas of science. Sports Science papers have shown lots of inaccurate and inappropriate terms for quantification of athletes’ performance and the psychobiological responses to exercise (e.g., internal load). In biomechanics, external and internal loads are forces acting externally and internally, inducing stress and strain in the biological tissues. Therefore, the current review present simple proposals to correct the inappropriate terms: 1) do not use the term external load when referring to the assessment of exercise time, distance, displacement, speed, velocity, acceleration, torque, work, power, impulse, etc.; 2) do not use the term internal load when referring to the assessment of psychobiological stress markers (i.e., session rating of perceived exertion, heart rate, blood lactate, oxygen consumption, etc.); 3) do not use the term impulse when expressing other calculus than integrating force with respect to time, and neither strain, when expressing other phenomena than the body deformation. Instead, the term exercise intensity is universal and can be used to describe all forms of exercise. Finally, duration should precisely be described according to physical quantities (e.g., time, distance, displacement, speed, velocity, acceleration, force, torque, work, power, impulse, etc.) and the units accomplish by use of the SI. These simple quantifications can be performed for the exercises, sessions, microcycles, mesocycles and macrocycles of the athletes. Such standardization will provide a consistent and clear communication among sports scientists and all areas of science.

Fabry-Perot air chamber was constructed at the melting point (splicing location) of two single-mode fibers by glycerin assisted self-expansion method. The morphology of the Fabry-Perot air chamber was fabricated and optimized by modulating the splicing parameters (drawing process, discharging location, time and intensity) and the fibers’ end-face (plane or arc). The in-line or reflected Fabry-Perot cavities have been applied to determine the tensile strain in the range of 0-1.2 N. The train sensing performance of the spherical shaped FP cavity has been experimentally demonstrated with the best sensitivity of 3.628 nm/N, corresponding to the resolution of ~0.005 N. The proposed FP fiber sensor has the advantages of low cost, fast fabrication and easy-integration with the common fiber system.

The Apennine sector formed by Sannio and Irpinia is one of the most important seismic districts in Italy, representing a good case of study due to the plenty of recorded earthquakes that have therein occurred from Roman times up to nowadays. We have merged the historical record and the new satellite techniques that allow a precise determination of ground movements, and then derived physical dimensions like strain rate. In this way, we have verified that in Irpinia the hazard of new strong shocks forty years after one of the strongest known seismic events in the district is still high. This aspect must be considered very important from many points of view, particularly for Civil Protection plans, as well as civil engineering and urban planning development.

Based on the kinematic approach of the limit analysis and slip-line theories, this paper proposes a new 2D analytical model to evaluate the collapse support pressure to ensure the face stability of a circular tunnel in purely cohesive soils driven by a shield. The normality conditions, the yield criterion and the vertical soil arching effect are considered in the analytical model. Two upper bound solutions corresponding to the ratio of the cover to the diameter (C/D) are derived from considering the mechanisms based on the motion of rigid multi-blocks. Comparisons are made with existing upper and lower bound solutions published in previous articles. The results are close to the solutions of practical engineering. The failure mechanisms proposed in this study provide a better explanation for the failure process in the heading of the tunnel face.

Myocardial deformation imaging (strain imaging) is a technique to directly quantify the extent of myocardial contractility and overcomes several of the limitations of ejection fraction. The application of the most commonly used strain imaging method; speckle-tracking echocardiography to patients with sepsis cardiomyopathy heralds an exciting development to the field. However; the body of evidence and knowledge on the utility, feasibility and prognostic value of left ventricular global longitudinal strain in sepsis cardiomyopathy is still evolving. We conducted a review of literature on utility of left ventricular global longitudinal strain in sepsis cardiomyopathy. We discuss the role of left ventricular global longitudinal strain in mortality prediction, utility and limitations of the technique in the context of sepsis cardiomyopathy.

The statistics of grain displacements probability distribution function (pdf) during the shear of a granular medium displays an unusual dependence with the shear increment upscaling as recently evinced [Phys. Rev. Lett. 115 238301 2015]. Basically, the pdf of grain displacements has clear nonextensive ($q$-Gaussian) features at small scales but approaches to Gaussian characteristics at large shear window scales -- the granulence effect. Here, we extend this analysis studying a larger system (more grains considered in the experimental setup) which exhibits a severe shear band fault during the macroscopic straining. We calculate the pdf of grain displacements and the dependency of the $q$-statistics with the shear increment. This analysis have shown a singular behavior of $q$ at large scales, displaying a non-monotonic dependence with the shear increment. By means of an independent image analysis, we demonstrate that this singular non-monotonicity could be associated with the emergence of a shear band within the confined system. We show that the exact point where the $q$-value inverts its tendency coincides with the emergence of a giant percolation cluster along the system, caused by the shear band. We believe that this original approach using Statistical Mechanics tools to identify shear bands can be a very useful piece to solve the complex puzzle of the rheology of dense granular systems.

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

In this study, the model proposed by Yang et al. to generalize the stress–strain model for unconfined concrete with consideration of the size effect is expanded. Sim et al.’s compressive strength model that is based on the function of specimen width and aspect ratio was used for the maximum stress. In addition, a strain at the maximum stress was formulated as a function of compressive strength by considering the size effect using the regression analysis of datasets compiled from a wide variety of specimens. The descending branch after the peak stress was formulated with consideration of less dissipated area of fracture energy with the increase in specimen width and aspect ratio in the compression damage zone (CDZ) model. The key parameter for the slope of the descending branch was formulated as a function of specimen width and aspect ratio, concrete density, and compressive strength of concrete considering the size effect. Consequently, a rational stress–strain model for unconfined concrete was proposed. This model explains the trends of the peak stress and strain at the peak stress to decrease and the slope of the descending branch to increase, as the specimen width and aspect ratio increase. The proposed model agrees well with the test results, irrespective of the compressive strength of concrete, concrete type, specimen width and aspect ratio. In particular, the proposed model for the stress–strain curve rationally considered the effect of decreasing peak stress and increasing the descending branch slope, with the increase in specimen width and aspect ratio.

To date, several independent methods and algorithms exist exploiting constraint-based stoichiometric models to find metabolic engineering strategies that optimize microbial production performance. Optimization procedures based on metaheuristics facilitate a straightforward adaption and expansion of engineering objectives as well as fitness functions, while being particularly suited for solving problems of high complexity. With the increasing interest in multi-scale models and a need for solving advanced engineering problems, we strive to advance genetic algorithms, which stand out due to their intuitive optimization principles and proven usefulness in this field of research. A drawback of genetic algorithms is that premature convergence to sub-optimal solutions easily occurs if the optimization parameters are not adapted to the specific problem. Here, we conducted comprehensive parameter sensitivity analyses to study their impact on finding optimal strain designs. We further demonstrate the capability of genetic algorithms to simultaneously handle (i) multiple, non-linear engineering objectives, (ii) the identification of gene target-sets according to logical gene-protein-reaction associations, (iii) minimization of the number of network perturbations, and (iv) the insertion of non-native reactions, while employing genome-scale metabolic models. This framework adds a level of sophistication in terms of strain design robustness, which is exemplarily tested on succinate overproduction in Escherichia coli.

Carbon nanotube (CNT) yarns are fiber-like materials that exhibit excellent mechanical, electrical and thermal properties. More importantly, they exhibit a piezoresistive response that can be tapped for sensing purposes. The objective of this study is to determine experimentally the piezoresistive response of CNT yarns that are embedded in a polymeric medium while subjected to either compression or tension, and compare it with that of the free or unconstrained CNT yarns. The rationale for this study is the need to know the response of the CNT yarn while in a medium, which provides a lateral constraint to the CNT yarn thus mimicking the response of integrated CNT yarn sensors. The experimental program will include the fabrication of samples and their electromechanical characterization. The CNT yarns are integrated in polymeric beams and subjected to four-point bending, allowing the determination of their response under tension and compression. The electrical resistance data from an Inductance-Capacitance-Resistance (LCR) device is used with the data acquired from the mechanical testing system to determine the piezoresistive response of the CNT yarns. This data and information will be used for future modeling efforts and to study the phenomena that occur when CNT yarns are integrated in polymeric and composite materials and structures.

The stability of deep soft rock tunnels is of particular concern under seepage conditions. Aiming at thoroughly discussing the seepage actions and their consequences on the support scheme of such structures, the host rocks of the Weilai Tunnel situated in Guangxi province of China are taken as the research substance. Emphasizing on seepage conditions, stresses, displacements and plastic zone radii along the surrounding rocks of such tunnel are adequately examined taking into consideration the Mogi-Coulomb strain criterion and the elastic-plastic theory. Subsequently, based on strain-softening model, the coupled actions of seepage and softening on the rocks surrounding the tunnel are studied. According to the results, it is revealed that the support scheme of deep soft rock tunnels must be of highest resistance possible to better decrease the plastic zone and the tangential stress along the host rocks. Moreover, throughout the surrounding rocks, the dissemination of pore water pressure is strongly affected by the uneven permeability coefficient under anisotropic seepage states. Combined effects of softening and seepage are very dangerous for the surrounding rocks of deep-buried tunnels. To better guarantee reasonable longevity of such tunnels, long-term monitoring of their support structures with reliable remote sensors is strongly recommended.

For semiconducting two-dimensional transition metal dichalcogenides, carrier transport proper-ties of the material are affected by strain engineering. In this work, we investigate the carrier mo-bility of monolayer hafnium disulphide (HfS2) under different biaxial strains by first-principles calculations combined with Kubo-Greenwood mobility approach and compact band model. The decrease/increase in effective mass of conduction band of monolayer HfS2 caused by biaxial ten-sile/compressive strain is the major reason for the enhancement/degradation of its electron mobil-ity. Lower hole effective mass of valence bands in the monolayer HfS2 under biaxial compressive strain results in the better hole transport performance of monolayer HfS2 than the one with biaxial tensile strain. In summary, biaxial compressive strain decreases both effective mass and phonon scattering rate of monolayer HfS2, resulting in an increase in carrier mobility. When the biaxial compressive strain reaches 4%, for the conduction band of monolayer HfS2, electron mobility en-hancement ratio is ~90%. For the valence band of monolayer HfS2, the maximum hole mobility enhancement ratio appears ~13% at biaxial compressive strain of 4%. Our results indicate that the carrier transport performance of monolayer HfS2 can be greatly improved by the strain engineer-ing.

Background. Myocardial involvement mediated by chronic obstructive pulmonary disease (COPD) is a common cause of morbidity and mortality. Conventional transthoracic echocardiography (TTE) parameters are poor in the detection of subclinical myocardial dysfunction. Aim.To investigate the contribution of strain in the early detection of cardiac damage in stable COPD patients Methods. Group A and B patients with COPD were enrolled in this study. The COPD assessment test, spirometry, 6-minute walk test, and both conventional TTE and strain were performed in these patients. Results. 80 COPD patients, with a mean age 65.6 ± 8.9 years, were included. The. Left ventricular ejection fraction (LVEF) was 60.7 ± 5.1%. Right atrium and right ventricle (RV) strain were 24.5 ± 6.6% and -19.9 ± 3.7%, respectively. Additionally, left ventricle global longitudinal strain (LV GLS) was -21.1 ± 2. Forty-eight patients had impaired RV strain. Compared to COPD patient with normal RV strain, those with RV reduced starin had a lower 6meter walk distance (6MWD) (p=0.001) and forced expiratory volume in the first second (FEV1) (p=0.012), and a higher CAT score (p=0.012). A reduced RV strain was correlated with a higher risk of hospitalizations for acute exacerbation in the post inclusion year (55% versus 25%; p=0.024). No deaths were recorded during the follow-up period. No significant factors causing neither RA starin alteration nor LV GLS reduction were revealed. Conclusion. Group A and B COPD patients having normal conventional TTE parameters, speckle tracking is a key parameter in the detection of subclinical myocardial dysfunction.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

Myocardial involvement among critical patients with coronavirus disease 2019 (COVID-19) has a worse outcome. The occurrence of an imbalance in oxygen supply results in the release of pro-inflammatory cytokines which leads to increased ventilation support requirement and increase risk of mortality. Our aim was to evaluate the association between hs-Troponin I level and global longitudinal strain as evidence of myocardial involvement among critical COVID-19 patients. Methods. We performed prospective cohort study from February 1st – July 31st, 2021 at Dr. Soetomo General Hospital, Surabaya as referral center for COVID-19 care. Of the 65 critical COVID-19 included, 41 (63.1%) were men, with a median (interquartile range) age of 51.0 years (20.0-75.0).Subjects were recruited according to WHO criteria for severe COVID-19 and CDC criteria for myocarditis. All subjects recruited were examined using echocardiography to measure global longitudinal strain (GLS) and blood samples were taken to measure hs-Troponin. Subjects were then followed to assess their needs for mechanical ventilation and in-hospital mortality. Severe COVID-19 subjects with cardiac injury were associated with an increased need for intubation (78.5%) and an increased incidence of myocarditis (50.8%). There was an association between the use of intubation and the risk of mortality in patients (66.7% vs. 33.3%, p-value &lt;0.001). Both reduced GLS and increased hs-troponin are associated with increased myocarditis (p-value &lt;0.001 and 0.004 respectively). Reduced GLS is associated with higher mechanical ventilation needs (12.17 + 4.79 vs.15.65 + 4.90, p-value 0.02) and a higher mortality rate (11.36 + 4.64 vs. 14.74 + 4.82; p-value 0.005). Increased hs-troponin is associated with higher mechanical ventilation needs (25.33% vs. 3.56%, p-value 0.002) and a higher mortality rate (34.57% vs. 5.76%, p-value 0.002). Compared with contemporary controls, critical COVID-19 patients with myocardial involvement and elevated cardiac troponin level are associated with higher mechanical ventilation needs and a higher mortality rate.

This study investigates the microstructures and deformation mechanism of hetero-structured pure titanium under different high strain rates (500 s-1，1000 s-1，2000 s-1). The influence of strain rate on the deformation mechanism is examined. As the strain rate increases, the dominance of dislocation slip decreases while deformation twinning becomes more prominent. Notably, at a strain rate of 2000s-1, nanoscale twin lamellae are activated within grain with a size of 500nm, which is a rarely observed phenomenon in pure Ti. Additionally, martensitic phase transformation is also identified. These findings can greatly enhance our understanding of the mechanical responses of Ti and broaden the potential applications of Ti in dynamic deformation scenarios.

The flow stress of face-centered cubic (FCC) metals exhibits a rapid increase near a strain rate of 104 s-1 under fixed strain conditions. However, many existing constitutive models either fail to capture the mechanical characteristics of this plastic deformation or use piecewise strain rate hardening models to describe this phenomenon. Unfortunately, the piecewise models may suffer from issues such as discontinuity of physical quantities and difficulties in determining segment markers, and struggling to reflect the underlying physical mechanisms that give rise to this mutation phenomenon. In light of this, this paper proposes that the abrupt change in flow stress sensitivity to strain rate in FCC metals can be attributed to microstructural evolution characteristics. To address this, a continuous semi-empirical physical constitutive model for FCC metals is established based on the microstructural size evolution proposed by Molinari-Ravichandran and the dislocation motion slip mechanism. This model effectively describes the mutation behavior of strain rate sensitivity under fixed strain, particularly evident in the annealed OFHC. The predicted results of the model across a wide range of strain rates (10-4 − 106 s-1) and temperatures (77 − 1096 K) demonstrate relative errors generally within ±10% of the experimental values. Furthermore, the model is compared to five other models, including Mechanical Threshold Stress (MTS), Nemat-Nasser-Li (NNL), Preston-Tonks-Wallace (PTW), Johnson-Cook (JC), and Molinari-Ravichandran (MR) models. A comprehensive illustration of errors reveals that the proposed model outperforms the other five models in describing the plastic deformation behavior of OFHC. The error results offer valuable insights for selecting appropriate models for engineering applications and provide significant contributions to the field.

Research has been actively conducted on the materials used to commercialize finished products that use hydrogen energy. Hydrogen embrittlement that occurs when hydrogen atoms penetrate metals is the largest problem that must be addressed first regarding safety. Because liquefied hydrogen has an 800 times higher density than hydrogen gas, hydrogen has been stored and transported through liquefaction at -253℃ using helium gas as a refrigerant. However, even if extreme temperatures below zero are maintained, natural vaporization loss that reduces liquefied hydrogen by 3 to 5% of the tank storage capacity per day occurs. In addition, when liquefied hydrogen is converted into high-pressure hydrogen gas for use, it is difficult to completely prevent the loss of the gas, even if sealing technology is applied to prevent gas leaks in transport and storage tanks. Therefore, methods to minimize the loss of hydrogen, establishment of assessment criteria for the embrittlement caused by a small amount of hydrogen gas, and related research are essential. We researched the hydrogen embrittlement resistance of SUS316L rods according to the tensile speed by conducting water electrolysis testing at room temperature, at which hydrogen gas is used to present hydrogen embrittlement assessment criteria for primary ring-shaped forged products.

We present the results of a twofold experimental and computational study of (0001) GaN/AlN multilayers forming pseudomorphic superlattices. High-Resolution Transmission Electron Microscopy (HRTEM) shows that heterostructures with GaN Quantum Wells (QW) four c-lattice parameters thick are misfit-dislocation free. Accurate structural data are extracted from HRTEM images via a new methodology optimizing the residual elastic energy stored in the samples. Total energy calculations are performed with several models analogous to the experimental QWs with increasing thicknesses of GaN, whereas this of the AlN barrier is kept fixed at n=8 c-lattice parameters. With vanishing external stresses, minimum energy configurations of the studied systems correspond to different strain states. Linear elasticity accurately yields the corresponding lattice parameters, suppressing the need for on-purpose total energy calculations. Theoretically justified parabolic fits of the excess interfacial energy yield the values of interfacial stress and elastic stiffness as functions of the GaN QW thickness. Total species-projected densities of states and gap values extracted therefrom allow deciphering the effect of the evolving strain on the electronic structure of the superlattice. It is found that the gap energy decreases linearly with increasing the strain of the QW. These results are briefly discussed in the light shed by previous works from the literature.

This paper presents a finite element analysis of the bi-directional orthogonal model, which incorporates individual crack strain separation and tracking. The objective of the research is to expand the current shear friction model to manage bi-directional cracking at any angle, allowing for a more universal model that can be applied to intricate structures and non-proportional loading cases. The proposed model was initially developed as a total strain-based model, with the assumption that crack strains are equivalent to total strains, but was subsequently recalculated to improve accuracy by separating crack strains from total strains. Furthermore, a separate crack strain formulation was created to account for strains in the concrete's uncracked portions and locked-in crack strains. The article then discusses the testing of various convergence methods and loading programs to achieve high convergence. Comparative analyses of the generalized shear friction model with other models for crack orientation and loading cases similar to those of a reinforced concrete membrane are also presented. The MATLAB program successfully applied the bi-directional cracking model for one finite element under a uniform cyclical strain state, using a secant stiffness formulation.

The mass production of mosquitoes at an industrial scale requires efficient sex separation, which can be achieved through mechanical, genetic or artificial intelligence means. Compared with others methods, the genetic sexing approach offers the advantage of limiting costs and space by removing females at larval stage. We recently developed a GSS in Aedes albopictus based on the sex linkage of the rdl gene to the M locus, conferring dieldrin resistance in males only. It has been previously reported that dieldrin ingested by larvae can be detected in adults and bioaccumulated in predators, raising the question of its use at a large-scale. In this context, we performed several experiments aiming at optimizing dieldrin selection by decreasing both dieldrin concentration and exposure time while maintaining a stable percentage of females averaging 1%. We showed that the previously used dieldrin exposure induced an important toxicity as it killed 60% of resistant males at larval stage. We could easily lower this toxicity by reducing the dose and/or the exposure time to recover nearly all resistant males. We then quantified the residues of dieldrin in resistant male adults and showed that dieldrin toxicity in larvae was positively correlated with dieldrin concentrations detected in adults. Interestingly, we showed that the use of reduced dieldrin exposure led to a dieldrin detection in adult males that was below the sensitivity threshold of the Gas Chromatography Mass Spectrometry detection method. Presented data show that dieldrin exposure can be adjusted to suppress toxicity in males while achieving efficient sexing and lowering the levels of dieldrin residues in adults to barely detectable levels.

The perceived risk of being infected at work (PRIW) with COVID-19 represents a potential risk factor for workers during the current COVID-19 pandemic. In line with the job demands-resources (JD-R) model applied to safety at work, in this longitudinal study we propose that PRIW can be conceptualized as a job demand, whereas communication (i.e., the exchange of good-quality information across team members) can be conceived as a job resource. Accordingly, we hypothesized that PRIW at Time 1 (T1) would positively predict psychophysical strain at Time 2 (i.e., four months later). Furthermore, we hypothesized that communication at T1 would negatively predict psychophysical strain at T2. Overall, 297 workers took part in the study. The hypothesized relationships were tested using multiple regression analysis. Results supported our predictions: PRIW positively predicted psychophysical strain over time, whereas communication negatively predicted psychophysical strain over time. Also, results did not change after controlling for age, gender, and type of contract. Overall, this study suggests that PRIW and communication can be considered as a risk and a protective factor for work-related stress, respectively. Hence, to promote more sustainable working conditions, interventions should encourage organizations to optimize the balance between job demands and job resources related to COVID-19.

In the present work, cost-effective strain gauges were fabricated by using inkjet printing and photonic curing on flexible and recyclable PET substrates. Ohmic resistance (a.k.a. DC resistance) (R0) and complex electrical impedance (Z) as a function of test frequency were characterized, respectively, with the state-of-the-art electronic testing equipments. For the fabrication process, commercially available silver nanoparticle (AgNP) inks and printing substrates were used in order to eliminate any apriori ink processing. In order to validate the in-house cantilever beam measurement setup and devices, first, commercially available metallic foil strain gauges (with the provided gauge factor GF=2 by the manufacturer) were tested at different locations. Thereafter, the printed strain gauges were investigated with several repetitions at different measurement locations. The measurement results demonstrated an affordable, rapid and tailorable design and repeatable fabrication approach for strain gauges with GFavg~6.6, which has potential applications in remote sensing and structural monitoring applications.

Polymer materials are increasingly being used for sliding machine elements due to their numerous advantages. They are used even where they are deformed and in such a state they interact frictionally e.g. in machine hydraulics or lip seals. Few publications deal with the influence of deformation, which is the effect of e.g. assembly on tribological properties of polymeric material. This deformation can reach up to ε ≈ 20% and is achieved without increasing the temperature of the polymer material. The paper presents the results of investigations in which high-density polyethylene (PE-HD) was maintained in deformation by means of a special grip (holder). The wear of the sample was significantly higher than that of the undeformed sample. This effect persisted even after partial relaxation of the stress in the sample after 24 hours. Additional investigations were carried out to explain the obtained results. There were the microscopic observations of the surface after friction, measurements of microhardness and free surface energy. Changes in the value of surface free energy and a significant decrease in microhardness with deformation under tension were observed. Strained material had a different surface appearance after friction and a different size and form of wear products. It was indicated that it is probable that the cohesion of the material will decrease and that the character of the wear process will change as a result of tension. Tension without heating of polymeric material (PE-HD), e.g. as a result of assembly, has been qualified as a hazard to be taken into account when designing and analysing polymeric sliding elements.

The effect of reprocessing on the quasi-static uniaxial tensile behavior of two commercial polypropylene (PP) based composites is experimentally investigated and modeled. In particular, the studied materials consist of an unfilled high-impact PP and a talc-filled high-impact PP. These PP composites are subjected to repeated processing cycles including a grinding step and an extrusion step to simulate recycling at the laboratory level, the selected reprocessing numbers for this study being 0, 3, 6, 9 and 12. Because the repeated reprocessing leads to thermo-mechanical degradation by chain scission mechanisms, the tensile behavior of the two materials exhibits a continuous decrease of elastic modulus and failure strain with increasing number of reprocessing. A physically consistent three-dimensional constitutive model is used to predict the tensile response of non-recycled materials with strain rate dependence. For the recycled materials, the reprocessing effect is accounted by incorporating the reprocessing sensitive coefficient into the constitutive model for Young’s modulus, failure strain, softening and hardening equations. Our predictions of true stress - true strain curves for non-recycled and recycled 108MF97 and 7510 are in a good agreement with experimental data.

We describe the effect of the expansion of space on the wavelength of the light beam in a Fabry-Pérot interferometer. For an instrument such as the Laser Interferometer Gravitational-Wave Observatory (LIGO), which has high sensitivity and a long period of light storage, the wavelength ${\lambda }_L$ of laser photons are redshifted due to the expansion of space in each cavity by an amount $\delta \lambda$ given by $\delta \lambda /{\lambda }_L=H_0{\tau }_s\approx 8.8\times {10}^{-21}$ , where $H_0\approx 2.2\times {10}^{-18}{\mathrm{s}}^{-1}$ is the Hubble constant and ${\tau }_s\approx 4\mathrm{ms}$ is the light storage time for the cavity. Since ${\tau }_s$ is based on the cavity finesse $\mathcal{F}$ which depends on the laser beam full width at half maximum (FWHM) $\delta \omega$ of each cavity, we show that a difference in finesses between the LIGO arm cavities produces a signal $h_H\left(t\right)$ at the anti-symmetric output port given by $h_H\left(t\right)=2a_1{H}_0\left(\frac{1}{\delta {\omega }_X\left(t\right)}-\frac{1}{\delta {\omega }_Y\left(t\right)}\right),$ where $\delta {\omega }_X\left(t\right)$ and $\delta {\omega }_Y\left(t\right)$ are the beam FWHM at time t, respectively, for the X and Y arm cavities and $a_1$ is a beam proportionality constant to be determined expermentally. Assuming $a_1\approx 1$ , then for cavity beams FWHM of $\delta \omega \left(t\right)\approx (523.2\pm 31)\mathrm{rad}.{\mathrm{s}}^{-1}$ the output signal has the range $\mid h_H\left(t\right)\mid \le 1\times {10}^{-21}$ , which is detectable by advanced LIGO.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

This article raise a topic of critical examination of polypropylene, a key polymeric material, and its extensive application within the automotive industry, particularly focusing on the manufacturing of brake fluid reservoirs. The study aims to enhance the understanding of polypropylene's behavior under mechanical stresses through a series of laboratory destruction tests and numerical simulations, emphasizing the Finite Element Method (FEM). A novel aspect of this research is the introduction of the PEAK parameter, a groundbreaking approach designed to assess the material's resilience against varying states of strain, known as triaxiality. This parameter facilitates the identification of critical areas prone to crack initiation, thereby enabling the optimization of component design with a minimized safety margin, which is crucial for cost-effective production. The methodology involves conducting burst tests to locate crack initiation sites, followed by FEM simulations to determine the PEAK threshold value for the Sabic 83MF10 polypropylene material. The study successfully validates the predictive capability of the PEAK parameter, demonstrating a high correlation between simulated results and actual laboratory tests. This validation underscores the potential of the PEAK parameter as a predictive tool for enhancing the reliability and safety of polypropylene automotive components. The research presented in this article contributes significantly to the field of material science and engineering by providing a deeper insight into the mechanical behavior of polypropylene and introducing an effective tool for predicting crack initiation in automotive components. The findings hold promise for advancing the design and manufacturing processes in the automotive industry, with potential applications extending to other sectors.

The problems of modeling the human bladder and its stress-strain state under external static influence were considered. A method for identification of the anisotropic biomechanical characteristics of bladder tissue was proposed. A FEM model was created, which accepts into regard that the bladder is surrounded by fiber and affected by surrounding organs, and partially protected by pelvic bones. The model considered the presence of constant hydrostatic pressure on the walls of the bladder when it is full. It has been shown that isotropic mechanical characteristics of biological tissue can be used for studying the deformed state of a filled bladder if the filled bladder 300 ml is considered as initial non-deformed stage. This was shown by modeling and verification the effect of the external static force on the bladder. Numerical experiments were conducted based on the constructed model. To validate the results obtained, a series of natural experiments on the effect of external pressure on the bladder under ultrasound control was conducted. In the future, it is planned to use the constructed model to study rupture deformations of the bladder under the influence of static and dynamic loads.

Tanning, crucial for leather production, relies heavily on chromium yet poses risks due to chromium's oxidative conversion, leading to significant wastewater and solid waste generation. Physico-chemical methods are typically used for heavy metal removal, but they have drawbacks, prompting interest in eco-friendly biological remediation techniques like biosorption, bioaccumulation, and biotransformation. The EU Directive (2018/850) mandates alternatives to landfilling or incineration for industrial textile waste management, highlighting the importance of environmentally conscious practices for leather products' end-of-life management, with com-posting being the most researched and viable option. This study aimed to isolate microorganisms from tannery wastewater and identify those responsible for different types of tanned leather biodegradation. Using a leather biodegradation assay (ISO 20136) with tannery and municipal wastewaters as inoculum, bacterial shifts during leather biodegradation were observed. Over 10,000 bacterial species were identified in all analyzed samples, with 8 bacterial strains isolated from tannery wastewater. Identification of bacterial genera like Acinetobacter, Brevundimo-nas, and Mycolicibacterium provides insights into potential microbial candidates for enhancing leather biodegradability, wastewater treatment, and heavy metal bioremediation in industrial applications.

In recent years, strain sensors have penetrated various fields. The capability of sensors to convert physical signals into electrical signals is of great importance in healthcare. However, it is still challenging to obtain sensors with high sensitivity, large operating range and low cost. In this paper, a stretchable strain sensor made of a double-layer conductive network, including a biomimetic multilayer graphene-Ecoflex (MLG-Ecoflex) substrate and a multilayer graphene-carbon nanotubes (MLG-CNTs) composite up-layer was developed. The combined action of the two layers led to an excellent performance with an operating range of up to 580% as well as a high sensitivity (gauge factor (GFmax) of 1517.94). In addition, a pressure sensor was further designed using the bionic vein-like structure with a multi-layer stacking of MLG-Ecoflex/MLG-CNTs/MLG-Ecoflex to obtain a relatively high deformation along the direction of thickness. The device presented a high sensing performance (up to sensitivity of 0.433 kPa-1), capable of monitoring small movements of the human body such as vocalisations and gestures. The good performance of the sensors together with a simple fabrication procedure (flip-molding) make it potential for some applications, for example, human health monitoring and other areas of human interaction.

Environmentally friendly lead-free K1-xNaxNbO3 (KNN) ceramics possess electromechanical properties comparable to lead-based ferroelectric materials, but cannot meet the needs of device miniaturization, and the corresponding thin films lack of theoretical and experimental studies. To this end, we developed the nonlinear phenomenological theory for ferroelectric materials to study the effects of non-equiaxed misfit strain on the phase structure, electromechanical properties and electrical response of K0.5Na0.5NbO3 epitaxial films and constructed the in-plane misfit strain (u1-u2) phase diagrams. The results show that K0.5Na0.5NbO3 epitaxial film under non-equiaxed in-plane strain can exhibit abundant phase structures, including orthorhombic a1c, a2c and a1a2 phases, tetragonal a1, a2 and c phases, and monoclinic r12 phases. Moreover, in the vicinity of a2c-r12, a1c-c and a1a2-a2 phase boundaries, K0.5Na0.5NbO3 epitaxial films exhibit excellent dielectric constant ε11, while at a2c -r12 and a1c-c phase boundaries large piezoelectric coefficient d15 is observed. It was also found that high permittivity ε33 and piezoelectric coefficients d33 exist near the a2c - a2, r12- a1a2 and a1c-a1 phase boundaries due to the existence of polymorphic phase boundaries (PPB) in the KNN system, which makes it easy to polarize near the phase boundaries, and the polarizability changes suddenly, leading to electromechanical enhancement. In addition, the results show that the K0.5Na0.5NbO3 thin films possess a large electrocaloric response at the phase boundary at the r12-a1a2 and a1c-a1 phase boundaries. And the maximum adiabatic temperature change ∆T is about 3.62 K when the electric field change is 30 MV/m at room temperature, which is significantly enhanced compared with equiaxed strain. This study provides theoretical guidance for obtaining K1-xNaxNbO3 epitaxial thin films with excellent properties.

Recently, there has been remarkable progress in the development of smart textiles, especially knitted strain sensors, to achieve reliable sensor signals. Stable and reliable electro-mechanical properties of sensors are essential for using textile-based sensors in medical applications. How-ever, challenges associated with significant hysteresis and low gauge factor (GF) values remain for using strain sensors for motion capture. To evaluate these issues, a comprehensive investiga-tion of the cyclic electro-mechanical properties of weft-knitted strain sensors was conducted in the present study to develop a drift-free elastic strain sensor with a robust sensor signal for mo-tion capture for medical devices. Several variables were considered in the study, including the variation of the basic knit pattern, the incorporation of the electrically conductive yarn, and the size of the strain sensor. The effectiveness and feasibility of the developed knitted strain sensors are demonstrated through experimental evaluation, by determining the gauge factor, its non-linearity, hysteresis and drift. The developed knitted piezoresistive strain sensors have a GF of 2.4, a calculated drift of 50 %, 12,5 % hysteresis, and 0.3 % nonlinearity in parts.

In recent years, two-dimensional (2D) materials have attracted significant attention due to their distinctive properties, including exceptional mechanical flexibility and tunable electronic properties. Via the first-principles calculation, we investigate the effect of strain on the electronic properties of monolayer SnP2S6 and GeP2S6. We find that monolayer SnP2S6 is an indirect band gap semiconductor, while monolayer GeP2S6 is a direct band gap semiconductor. Notably, under uniform biaxial strains, SnP2S6 undergoes an indirect-to-direct band gap transition at 4.0% biaxial compressive strains, while GeP2S6 exhibits a direct-to-indirect transition at 2.0% biaxial tensile strain. The changes of the conduction band edge can be attributed to the high-symmetry point Γ being more sensitive to strain than K. Thus, the relocation of the conduction-band and valence-band edges in monolayer SnP2S6 and GeP2S6 induces a direct-to-indirect and indirect-to-direct band-gap transition respectively. Consequently, the strain is an effective band engineering scheme which is crucial for the design and development of next-generation nanoelectronic and optoelectronic devices.

A highly sensitive strain sensor based on tunable cascaded Fabry-Perot interferometers (FPIs) is proposed and experimentally demonstrated. Cascaded FPIs consist of a sensing FPI and a reference FPI which effectively generate the Vernier Effect (VE). The sensing FPI comprises a hollow core fiber (HCF) segment sandwiched between single-mode fibers (SMFs), and the reference FPI consists of a tunable air reflector, which is constituted by a computer programable fiber holding block to adjust the desired cavity length. Simulation results predict the dispersion characteristics of modes carried by HCF. The sensor’s parameters are designed corresponding to a narrow bandwidth range, i.e., 1530 nm to 1610 nm. Experimental results demonstrate that the proposed sensor exhibits optimum strain sensitivity of 23.9 pm/με in the range of 0 to 3000 με which is 13.73 times higher than the single sensing FPI strain sensitivity of 1.74 pm/με. The strain sensitivity of the sensor can be further enhanced by extending the source bandwidth. The proposed sensor exhibits ultra-low temperature sensitivity of 0.49 pm/°C in the wider temperature range of 25 °C to 135 °C, providing good isolation for eliminating cross-talk between strain and temperature. The sensor is very robust, cost-effective, easy to manufacture, repeatable, and shows a highly linear and stable response in the wider range of axial strain. Based on the sensor’s performance, it may suit plenty of practical applications in the real sensing world

The gastrointestinal (GI) tract is a continuous channel through the body that consists of the esophagus, the stomach, the small intestine, the large intestine, and the rectum. Its primary functions are to move the intake of food for digestion before storing and ultimately expulsion of feces from the rectum through the anal sphincter. The mechanical behavior of GI tissues thus plays a crucial role for GI function in health and disease. The mechanical properties are typically characterized by a constitutive biomechanical model, which is a mathematical representation of the relation between load and deformation in a tissue. Hence, validated biomechanical constitutive models are essential to characterize and simulate the mechanical behavior of the GI tract under physiological and pathological conditions. Numerous constitutive models have consequently been proposed over the past three decades, mainly inspired by work done in cardiovascular tissues. Here, a comprehensive review of these constitutive models is provided. This review is limited to studies where a model of the strain energy function is proposed to characterize the stress-strain relation of a GI tissue. Several needs are identified for more advanced modeling of GI biomechanics including: 1) Microstructural models that provide actual structure-function relations; 2) Validation of coupled electro-mechanical models accounting for active muscle contractions; 3) Human data under physiological and pathological conditions to develop and validate models. The findings from this review provide guidelines for using existing constitutive models as well as perspective and directions for future studies aimed at establishing new constitutive models for GI tissues.

Background: global longitudinal strain (GLS) measures myocardial deformation and is a sensitive modality for detecting subclinical myocardial dysfunction and predicting cardiac outcomes. The accuracy of speckle-tracking echocardiography (STE) is dependent on temporal resolution. A novel software enables relatively high frame rate (Hi-FR) (~200 fps) echocardiographic images acquisition which empowers us to investigate the impact of Hi-FR imaging on GLS analysis. The goal of this pilot study was to demonstrate the feasibility of Hi-FR for STE. Methods: In this prospective study, we acquired echocardiographic images using clinical scanners on patients with normal left ventricular systolic function using Hi-FR and conventional frame rate (Reg-FR) (~50 FPS). GLS values were evaluated on apical 4-, 2- and 3-chamber images acquired in both Hi-FR and Reg-FR. Inter-observer and intra-observer variabilities were assessed in Hi-FR and Reg-FR. Results: There were 143 resting echocardiograms with normal LVEF included in this study. The frame rate of Hi-FR was 190 ± 25 and Reg-FR was 50 ± 3, and the heart rate was 71 ± 13. Strain values measured in Hi-FR were significantly higher than those measured in Reg-FR (all p < 0.001). Inter-observer and intra-observer correlations were strong in both Hi-FR and Reg-FR. Conclusions: We demonstrated that strain values were significantly higher using Hi-FR when compared with Reg-FR in patients with normal LVEF. It is plausible that higher temporal resolution enabled the measurement of myocardial strain at desired time point. The result of this study may inform clinical adoption of the novel technology. Further investigations are necessary to evaluate the value of Hi-FR to assess myocardial strain in stress echocardiography in the setting of tachycardia.

We show how the excitonic features of biaxial MoS₂ flakes are very sensitive to biaxial strain. We find a lower bound for the gauge factors of the A exciton and B exciton of (-41 ± 2) meV/% and (-45 ± 2) meV/% respectively, which are larger than those found for single-layer MoS₂. Interestingly, the interlayer exciton feature also shifts upon biaxial strain but with a gauge factor that is systematically larger than that found for the A exciton, (-48 ± 4) meV/%. We attribute this larger gauge factor for the interlayer exciton to the strain tunable van der Waals interaction due to the Poisson effect (the interlayer distance changes upon biaxial strain).

This paper presents the results of investigations of the effects of hot deformation parameters in compression investigation on the austenite grain size in HSLA steel (0.16% C, 0.037% Nb, 0.004% Ti, 0.0098% N). The axisymmetric compression investigations were performed on cylindrical investigation specimens of d=1.2 using the Gleeble 3800 simulator. The strain rate=1s^-1÷15.9s^-1 and strain degree ε=1.2. Before deformation, the research specimens were austenitized at TA = 1100 ÷ 1250 °C. Metallographic observations of the primary austenite grains were conducted with an optical microscope, while the structure of dynamically recrystallized austenite, inherited by martensite, was examined by EBSD technique using a scanning electron microscope. Based on the analysis of investigation results, it was found that the size of dynamically recrystallized austenite grains in HSLA steel were clearly affected by hot compression parameters. In contrast, no significant impact of austenitising temperature on their size was found.

Abstract: The Inconel 625 is a nickel-based alloy has been widely used in the high-temperature application. The Inconel 625 exhibits unstable plastic flow at elevated temperature characterized by serrated yielding, known as Portevin-Le Chatelier effect. The aim of this work is to evaluate the mechanical properties at high temperatures of the Inconel 625. The tensile tests were performed in the temperature range of room temperature until 1000 °C and strain rate of 2x10^-4 to 2x10^-3 s^-1. The creep tests were performed in the temperature range of 600-700 °C, in the stress range of 500-600 MPa in a constant load mode. The surface fracture was observed by optical and scanning electron microscopy. Serrated stress-strain behavior was observed in the curves obtained at 200 to 700 °C, which was associated with the dynamic strain aging effect. The yield strength and the elongation values show an anomalous behavior as a function of the test temperature. An intergranular cracking was observed specimen tensile tested at 500 °C that can be attributed to the decohesion of the carbides along the grain boundaries. The fracture surface of the specimen tensile tested at 700 °C showed the predominance of transgranular cracking with tear dimples with a parabolic shape.

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (h_f) and the maximum depth (h_max) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s⁻¹ and 0.1 s⁻¹. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

Abstract: In order to explore new options for colon targeting, this study designs new polyelectrolyte complex (PEC) coacervate xerogels of chitosan (Ch) with Albizia procera (AP). It was determined by potentiometric titration tests that a 1:5 Ch/AP weight ratio was necessary for 1:1 charge stoichiometry. Rheological characterizations experiments were carried out for the pH independent coacervates and 1:5 coacervate was found to be having the highest G^/ value in the strain sweep experiment. In the frequency sweep experiments the coacervate (1:5) with the highest storage modulus (G^/) values was produced at pH 4.5.

Background Community infections of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) have increased rapidly since the emergence of the Omicron strain. During the eighth and ninth pandemic waves—when movement restrictions in the community were eased—the all-case registration system was changed, and the actual status of infection became uncertain. Methods We conducted regular rapid antigen tests (R-RAT) once or twice a week to examine the actual state of coronavirus disease (COVID-19) diagnosis among healthcare employees. Results Overall, 320 (1.42/day) and 299 (1.76/day) employees were infected in the eighth and ninth pandemic waves. During both periods, 59/263 doctors (22.4%), 335/806 nurses (41.6%), 92/194 administrative employees (47.4%), and 129/218 clinical laboratory technicians (59.2%) were infected. In the eighth wave, 56 of 195 employees were infected through close contact; in the ninth wave, 26 of 62 employees were infected. No significant difference was observed in the number of vaccinations between infected and non-infected employees. The positivity rate of R-RAT was 0.41% and 0.45% in the eighth and ninth waves. R-RAT detected infection in 212 and 229 employees during the eighth and ninth waves, respectively; the ratio of R-RAT-detected positive employees to those who reported infection was significantly higher during the ninth wave (odds ratio: 1.67, 95% confidence interval: 1.17–2.37, p

Varicella (chickenpox) is one of the most common infectious diseases in preschool children and can be prevented by immunization. While immunization program promotes higher vaccine coverage, there are still challenges with implementing vaccination programs particularly in low-income countries. Economic barriers can increase inequality in vaccination, which highlights the importance of distributing cost-effective varicella vaccines. Varicella vaccines have been developed with two main Varicella-Zoster Virus (VZV) strains globally: MAV/06 and Oka strains. Most of the vaccines are based on the Oka strain, while MAV/06 strain vaccines were exclusively developed by GC Biopharma. Although more than 30 million doses of MAV/06 vaccines as cost-effective vaccines have been distributed internationally, there is no comprehensive review on safety, immunogenicity, and effectiveness of MAV/06 vaccines in the literature. This paper aims to summarize and present more than 30 years of accumulated evidence from research on safety, immunogenicity, and effectiveness of MAV/06 vaccines. We expect that MAV/06 vaccines as cost-effective varicella vaccines make a significant contribution to improving global public health and health equality in children.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

In this paper, a novel nonlocal strain gradient anisotropic elastic shell model is developed to analyse the vibrations of simply supported single‒walled carbon nanotubes (SWCNTs). Sanders‒Koiter shell theory is used to obtain the strain‒displacement relationships. Eringen nonlocal elasticity theory and Mindlin strain gradient theory are adopted to derive the constitutive equations, where the anisotropic elastic constants are expressed via Chang molecular mechanics model. The complex variable method is used to analytically solve the equations of motion and to obtain the natural frequencies of SWCNTs. First, the anisotropic elastic shell model is validated via comparisons with the results of molecular dynamics simulations reported in the literature. Then, the effect of nonlocal and material parameters on the natural frequencies of SWCNTs with different geometries and wavenumbers is analysed. From the numerical simulations it is obtained that the natural frequencies decrease with increasing nonlocal parameter, while they increase with increasing material parameter. Moreover, the decrease of natural frequencies with increasing SWCNT radius is exponential as the material parameter increases, while it is linear as the nonlocal parameter increases. Finally, as the number of waves increases, the natural frequencies linearly vary with increasing nonlocal parameter, while they exponentially increase with increasing material parameter.

Various crystallite size estimation methods were used to analyze X-ray diffractograms of spherical cerium dioxide and donut-like titanium dioxide anatase nanoparticles aiming to evaluate their reliability and limitations. The microstructural parameters were estimated from Scherrer, Monshi, Williamson-Hall, and their variants: i) uniform deformation model, ii) uniform strain deformation model, and iii) uniform deformation energy density model, and also size-strain plot, and Halder-Wagner method. For that, and improved systematic Matlab code was developed to estimate the crystallite sizes and strain, and the linear regression analysis was used to compare all the models based on the coefficient of determination, where the Halder Wagner method gave the highest value (close to 1). Therefore, being the best candidate to fit the X-ray Diffraction data of metal-oxide nanoparticles. Advanced Rietveld was introduced for comparison purposes. Refined microstructural parameters were obtained from a nanostructured 40.5 nm Lanthanum hexaboride nanoparticles and correlated with the above estimation methods and transmission electron microscopy images. In addition, electron density modelling was also studied for final refined nanostructures, and μ-Raman spectra were recorded for each material estimating the mean crystallite size and comparing by means of a phonon confinement model.

The need for quick and easy deflection calculations of various prefabricated slabs causes that simplified procedures and numerical tools are used more and more often. Modelling of full 3D finite element (FE) geometry of such plates is not only uneconomical but often requires the use of complex software and advanced numerical knowledge. Therefore, numerical homogenization is an excellent tool, which can be easily employed to simplify a model, especially when accurate modelling is not necessary. Homogenization allows for simplifying a computational model and replacing a complicated composite structure with a homogeneous plate. Here, a numerical homogenization method based on strain energy equivalence is derived. Using the method proposed, the structure of the prefabricated concrete slabs reinforced with steel spatial trusses is homogenized to a single plate element with an effective stiffness. There is a complete equivalence between the full 3D FE model built with solid elements combined with truss structural elements and the simplified homogenized plate FE model. The method allows for the correct homogenization of any complex composite structures made of both solid and structural elements, without the need to perform advanced numerical analyses. The only requirement is a correctly formulated stiffness matrix of a representative volume element (RVE) and appropriate formulation of the transformation between kinematic constrains on RVE boundary and generalized strains.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

The alien invasive insect pest Spodoptera frugiperda Smith (Lepidoptera: Noctuidae), commonly referred to as Fall Armyworm (FAW), is a polyphagous insect feeding on more than 350 host plants in addition to maize in its native habitat. Due to the voracious nature of FAW, significant yield losses on maize production were reported across the African continent since its detection in 2016. Despite being a polyphagous insect, little is known about its alternative host plants in the new habitat including Mozambique. This study aimed to assess the host range of FAW in the central province of Manica, Mozambique. A field survey was conducted from May to August 2019 (dry season of 2018/2019 cropping season) and in December 2019 and January 2020 (rainy season of 2019/2020 cropping season) in maize fields and crops often mixed with maize or located in the vicinity of maize fields. A total of 1291 fields were surveyed. In each field, 20 plants were selected in a “W” pattern and checked for the presence of FAW egg masses and/or larvae. At the time of the sampling, no evidence was found suggesting that in Manica province FAW feeds in crops other than maize because out of 35 different crops surveyed, FAW was only recorded on maize. Results from this study suggest that the strain of FAW occurring in Manica province might be the one specialized in maize or the continuous availability of maize fields throughout the year is influencing the choices of the host plants of this invasive insect pest.