: Low-temperature growth of diamond films by chemical vapor deposition (CVD) method is not so widely reported and especially its initial periods of nucleation and growth phenomenon are of particular interest to the researchers. Four sets of substrates were selected for growing diamond films by linear antenna microwave plasma enhanced CVD (LA-MPCVD). Among them, silicon and sapphire substrates were pre-treated with detonation nanodiamond (DND) seeds before diamond growth for enhancement of its nucleation. On the other hand, carbon nanotube (CNT) films on Si substrates were also used as another template for LA-MPCVD diamond growth. In order to enhance the diamond nucleation during CVD growth, some of the CNT films were again pre-treated by electrophoretic deposition (EPD) of diamond nanoparticles. All these substrates were then put inside the LA-MPCVD chamber for growing diamond films under variable processing conditions. Microwave input powers (1100 – 2800 W), input power modes (pulse or continuous), antenna to stage distances (5 - 6.5 cm), process gas recipes (with or without CO2), methane gas percentages (3 - 5%), deposition times (11 – 120 minutes) were altered to investigate their effect on the growth of diamond film on the pre-treated substrates. The substrate temperatures were found to vary from as low as 170oC to a maximum of 307oC during the alteration of the different processing parameters. Contrary to the conventional MPCVD, it was observed that during the first hour of LA-MPCVD diamond growth, DND seeds or the nucleating structures, do not coalesce together to make a continuous film. Deposition time was the most critical factor in fully covering the substrate surfaces with diamond film, since the substrate temperature could not become stable during the first hour of LA-MPCVD. CNT was found to be oxidised rapidly under LA-MPCVD plasma conditions; therefore, a CO2-free process gas recipe was used to reduce CNT burning. Moreover, EPD-coated CNT was found to be less oxidised by the LACVD plasma during diamond growth.

Human epidermal growth factor receptor 2 (HER2) belongs to the ErbB family, a group of four transmembrane glycoproteins with tyrosine kinase activity, all structurally related to the epidermal growth factor receptor (EGFR). These tyrosine kinases are involved in the transmission of cellular signals controlling normal cell growth and differentiation. If this transmission goes awry, it can lead to dysregulated growth of the cell. HER2 specifically can be implicated in the pathogenesis of at least eight malignancies. HER2 positivity quickly became a well characterized indicator of aggressiveness and poor prognosis, with high rates of disease progression and mortality. After realizing the implication of HER2, it first became investigated as a target for treatment in breast cancer, and later expanded to areas of research in other cancers types. To this day, the most therapeutic advancements of anti-HER2 therapy have been in breast cancer, however, there have been strong advancements made in the incorporation of anti HER2 therapy in other cancer types as well. This comprehensive review dissects HER2 to its core incorporating the most up to date information. The topics touched upon are discussed in detail and up to 200 published sources from the most highly recognized journals have been integrated. The importance of knowing about HER2 is exemplified by the groundbreaking advancements that have been made, and the change in treatment plans it has brought to the oncological world in the last twenty years. Since, its ground breaking discovery there has been significant breakthroughs in knowledge regarding the actual receptor, the receptors biology, its mechanism of action, advancements in tests to detect HER2 and significant strides on how to best incorporate targeted treatment. Due to the success of this field thus far, the review concludes by discussing the future of novel anti-HER2 therapy currently in development that everyone should be aware of.

Iterative Stochastic decoding is an alternative to standard fixed-point decoding of Low-density parity check codes (LDPC) to reduce inter-node routing. In this paper, we propose a Flexible Field-Programmable Gate Array (FPGA)-Based Stochastic decoding (SD) hardware architecture for LDPC codes in the Fifth-Generation (5G) New Radio (NR) Standard that supports decoding of set of various code rates. This decoder’s runtime flexibility is desirable to switch a better performing code rate automatically based on the channel conditions without the extra time needed for reprogramming of FPGA. An offline design method is implemented to generate the hardware description language (HDL) code description of the decoder for the required code-rate set, which is further synthesized and integrated into the Xilinx Kintex-7 series FPGA board to determine the hardware resource utilisation and processing throughput. The Synopsys design tools were employed during both the simulation and synthesis stages, in combination with TSMC 65-nm CMOS standard cell technology, to facilitate comparative analysis. Compared with state-of-the-art designs, the proposed architecture reduces hardware utilization by up to 26% and achieved energy efficiency by 52%.

Our objective was to evaluate whether pregnancy is prolonged by use of a proteomics-based maternal serum screening test followed by treatment interventions. This is a secondary analysis of the PREVENT-PTB randomized trial comparing screening with the PreTRM test versus no screening. The primary trial analysis found no significant between-group difference in preterm birth rate. Rather than considering a dichotomous outcome (preterm vs term), we treated gestational age at birth as a continuous variable using survival analysis. We also evaluated between-group difference in NICU length of stay and duration of respiratory support. Results indicated that pregnancy was significantly prolonged in subjects screened with PreTRM test compared to controls (adjusted hazard ratio 0.53, 95% confidence interval 0.36-0.78, P <0.01). Newborns of screened subjects had significantly shorter NICU stay but no significant decrease in duration of respiratory support. In the PreTRM screen-positive group, interventions that were associated with pregnancy prolongation included care management and low-dose aspirin but not 17-hydroxyprogesterone caproate. We concluded that screening with the PreTRM test followed by interventions for screen-positive pregnancies can prolong pregnancy and reduce NICU-LOS.

Applications for Wireless Sensor Networks (WSNs) range from monitoring the environment to automating factories. However, sustained and effective functioning is made more difficult by Sensor Nodes (SNs) limited energy supplies in which optimization is the main issue. So with the aim of increasing the lifespan by decreasing the energy consumption of WSN, Low-Energy Adaptive Clustering Hierarchy (LEACH) protocol with Deep Learning (DL) algorithm is analyzed in this paper. LEACH is a hierarchical mechanism that elects Cluster Heads (CHs) and regularly rotates their positions in order to allocate energy use effectively by using the same amount of energy. However, Deep Learning (DL) method is used to further improve energy optimization. In many applications, the types of Deep Learning methods like Artificial Neural Networks (ANNs) have shown to be very useful. Using this method, WSNs may make more efficient decisions that reduce energy consumption. Data aggregation, duty cycling, and transmission protocols may all be optimized by Deep Learning model's ability to recognize patterns and forecast network behavior. This results in lower energy consumption, a longer lifespan for the network, and better overall performance.

Powerful emitters of the ultraviolet C (UVC) light in the wavelength range of 230-280nm are necessary for the development of effective and safe optical disinfection technologies, high-sensitive optical spectroscopy and non-line-of-sight optical communication. This review considers such UVC-emitters with electron-beam pumping of heterostructures with quantum wells in the (Al,Ga)N material system. The important advantages of these emitters include the absence of the critical problem of p-type doping and the possibility of achieving record (up to several tens of watts for peak values) output optical power values in the UVC range. The review consistently considers about a decade of world experience in the implementation of various UV emitters with various types of thermionic, field-emission, and plasma-cathode electron guns (sources) used to excite various designs of active (light-emitting) regions in heterostructures with quantum wells AlxGa1-xN/AlyGa1-yN (x = 0 − 0.5, y = 0.6 − 1) fabricated either by metal-organic chemical vapor deposition or by plasma-activated molecular beam epitaxy. Special attention is paid to the production of heterostructures with multiple quantum wells/two-dimensional(2D) quantum disks GaN/AlN with a monolayer (1ML ~ 0.25nm) thickness, which ensures a high internal quantum efficiency of radiative recombination in the UVC range, low elastic stresses in heterostructures, and a high output UVC-optical powers.

The DNS of film boiling requires strong computational resources that are difficult to obtain for a daily CFD use by the practitioners of the industrial R&D experts. On the other hand, the film boiling experiments are associated with the usage of the expensive and highly sophisticated apparatus, and the research to this end is found to be relatively difficult due to high heat flow rates that are present in the process itself. When combined with a transient heat conduction in a solid, the problem becomes significantly difficult. Therefore, a novel method in computation of conjugate heat transfer during film boiling in a quiescent liquid has been proposed in this paper. The method relies on the solution of mass, momentum and energy conservation equations in a two-fluid framework, supplemented with the appropriate closures. Furthermore, the turbulent flow has been found as an important parameter in obtaining the accurate solution of the temperature field evolution in a solid specimen, via the proper modeling of turbulent kinetic energy (TKE) value, that has been imposed as a constant value, i.e., the frozen turbulence approach. It was found, in addition, that the appropriate TKE value can be obtained by use of Kelvin-Helmholtz instability theory in conjunction with the boundary layer theory. The obtained results show excellent agreement with the experimental data within the first 15 s of the experiment, i.e., the first ca. 10 % of the total duration of the film boiling mode of heat transfer. Furthermore, the heat transfer coefficient has matched the error bands prescribed by the authors of the paper that has presented the correlations, whilst the averaged values are far beyond this band, i.e., are slightly more than 30 % higher. The further inspection has revealed a measure of similarity between the computational result of the volume fraction field distribution and the experiment, thus confirming the capability of the method to obtain realistic interface evolution in time. The method has shown full capability for further pursuing the industrial-scale film boiling problems that involve turbulent flow and the conjugate heat transfer approach.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

There is a systematic exclusion of gender-based violence, safe abortion, reproductive cancers, infertility services, comprehensive sexuality education, sexuality services, and STI’s other than HIV in essential health packages in LMICs. To accelerate progress on sexual reproductive health (SRH), the Guttmacher–Lancet Commission proposed the adoption of these interventions into an essential health package of SRH services that should be universally available. In this commentary, we use a healthcare priority-setting processes lens to review the importance of these services for universal health coverage. We isolate inherent challenges in social value judgments for terminal, process and content evidence for their healthcare priority-setting. We then advance promising emerging practical examples from low to middle-income countries on evidence-informed decision-making processes. We recommend capacity development through regional support, generating equity and efficiency evidence and strengthening political and publicly acceptable processes to institutionalise and operationalise evidence-informed decision-making.

This paper is a mini literature review about electromagnetic field’s effects on cells, tissues and new treatment modalities. We have reviewed a papers which have been published in high quality journals in the last 5 years as two authors. This review’s aim is to be a resource for experimental studies about electricity’s effects on cell biology and pathophysiology. As a result of this literature review, we found that especially extremely low electric frequency and intermediate frequency fields have very important pathophysiological effects. We have mentioned four important expressions on this subject; electroporation, electrofusion, electrochemotherapy, gene electrotransference. Two different new treatment approaches have been developed by use of these two important electrical waves. First is tumor treating fields and the other is pulsed electric fields. Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma multiforme and malign melanoma.Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma and melanoma.

Selenium-rich Au-Ag mineralization has been discovered in the Kremnica ore district, central Slovakia. The mineralization is hosted by a single quartz-dolomite vein hosted by Neogene propyllitized andesites of the Kremnica stratovolcano. Ore mineralogy and crystal chemistry of individual ore minerals have been studied here. The early base-metal ore mineralization composed of pyrite, sphalerite and chalcopyrite lacks selenium, whereas the superimposed Au-Ag paragenesis is Se-enriched. The Au-Ag alloys, uytenbogaardtite, minerals of the galena-clausthalite series, acanthite-naumannite series, diaphorite, miargyrite, pyrargyrite-proustite, polybasite group, minerals of the tetrahedrite group and andorite branch (andorite IV, andorite VI, Ag-excess fizélyite), freislebenite, and rare Pb-Sb sulphosalts (scaiinite, robinsonite, plagionite) have been identified here. Besides selenides, the most Se-enriched phases are miargyrite, proustite-pyrargyrite, and polybasite-pearceite, whose Se contents are among the highest reported worldwide. In addition, one new phase has been found, corresponding to a Se-analogue of pearceite containing 2.08 - 3.54 apfu Se. The style of mineralization, paragenetic situation, and chemical trends observed in individual minerals are comparable to those of Au-Ag low-sulphidation epithermal Au-Ag mineralizations of the Kremnica and neighboring Štiavnica and Hodruša-Hámre Ore Districts, however, the pronounced enrichment in selenium is a specific feature of the studied vein only.

The application of the sensors optical fiber in the areas of scientific instrumentation and industrial instrumentation is very attractive due to its numerous advantages. In the industry of civil engineering for example, quasi-distributed sensors made with optical fiber are used for reliable strain and temperature measurements. Here, a quasi-distributed sensor in the frequency domain is discussed. The sensor consists of a series of low-finesse Fabry-Perot interferometers where each Fabry-Perot interferometer acts as a local sensor. Fabry-Perot interferometers are formed by pairs of identical low reflective Bragg gratings imprinted in a single mode fiber. All interferometer sensors have different cavity length, provoking the frequency-domain multiplexing. The optical signal represents the superposition of all interference patterns which can be decomposed using the Fourier transform. The frequency spectrum is analyzed and sensor´s properties were defined. Following, a quasi-distributed sensor was numerically simulated. Our sensor simulation considers sensor properties, signal processing, noise system and instrumentation. The numerical results show the behavior of resolution vs. signal-to-noise ratio. From our results, the Fabry-Perot sensor has high resolution and low resolutions. Both resolutions are conceivable because the FDPA algorithm elaborates two evaluations of Bragg wavelength shift

Combustion parameters are the important aspects in the development and research of an internal combustion engines. Hence present work is an attempt to develop an artificial neural network (ANN) model for anticipating the combustion characteristics of computerized CI DI VCR, four strokes, single cylinder, and water cooled engine using mixture of two biodiesel and diesel blends as a fuel. The two biodiesel selected are Jatropha and Simarouba and mixed in the ratio of 75:25. Two biodiesel mixtures is used for the preparation of various blends with diesel. Experiments are carried out at different compression ratio, at different % load and blends B20, B40, B60and neat diesel (B00) fuel to accumulate the assorted combustion data. The input variables are % load, compression ratio, blends and crank angle. The outputs well thought-out are cylinder pressure (CP), net heat release rate (NHRR), cumulative heat release (CHR), rate of pressure rise (RPR), mass fraction burned (MFB) and maximum cylinder pressure. The assessment is focused on developing artificial neural network for the prediction and verifying the combustion characteristics of engine. MATLAB software is used for analysis of different combustion aspects of the engine. Multilayer neural network perceptions are used with Feed-Forward Back Propagation algorithm with performance function for mapping the input and output parameters. The experimental outcomes are compared with ANN estimated results for the analysis. The outcome from the study authenticate that experimental results are in match with ANN results. The accuracy of the ANN model shows the developed model can effectively predict the engine combustion characteristics with excellent regression coefficients ‘R’ and its values are close to unity and the mean square errors are extremely less. ANN model approach is competent towards predicting the combustion aspect of diesel engine with good accuracy

Bioactive lipids are involved in cellular signalling events with links to human disease. Many of these are involved in inflammation under normal and pathological conditions. Despite being attractive molecules from a pharmacological point of view, detection and quantification of lipids has been a major challenge. Here, we have optimised a liquid chromatography dynamic multiple reaction monitoring targeted mass spectrometry (LC-dMRM-MS) approach to profile eicosanoids and fatty acids in biological samples. In particular, by applying this analytic workflow to study a cellular model of Chronic Myeloid Leukaemia (CML), we found that intra- and extra-cellular 2-Arachidonoylglycerol (2-AG), intracellular Arachidonic Acid (AA), and extracellular Prostaglandin F_2α (PGF_2α), 5-Hydroxyeicosatetraenoic acid (5-HETE), Palmitic acid (PA, C16:0) and Stearic acid (SA, C18:0) were altered in response to immunomodulation by type I Interferon (IFN-I), a currently approved treatment for CML. Our observations indicate changes in eicosanoid and fatty acid metabolism with potential relevance in the context of cancer inflammation and CML.

Evaporating liquid sessile drop deposited on horizontal surface is an important object of applications (printing technologies, electronics, sensorics, medical diagnostics, hydrophobic coatings, etc.) and theoretical investigations (microfluidics, self-assembly of nanoparticle, crystallization of the solute, etc.). The arsenal of formulas for calculating the slow evaporation of an axisymmetric drop of capillary dimensions deposited on a flat solid surface is reviewed. Such characteristics as vapor density, evaporation flux density, total evaporation rate are considered. Exact solutions obtained in the framework of the Maxwellian model, in which the evaporation process of the drop is limited by vapor diffusion from the drop surface to the surrounding air, are presented. The summary covers both well-known results obtained during the last decades and new results published by us in the last few years, but practically unknown to the wide scientific community. The newest formulas, not yet published in refereed publications, concerning exact solutions for a number of specific contact angles are also presented. In addition, new approximate solutions are presented for the first time (total evaporation rate and mass loss per unit surface area per unit time in the whole range of contact angles ), which can be used in modeling without requiring significant computational resources.

(1) Background: Co-morbidities such as hypertension and cardiovascular disease are major risk factors for severe COVID-19. The renin-angiotensin-system (RAS) is critically involved in their pathophysiology and is counterbalanced by both angiotensin-converting enzyme 2 (ACE2), the functional receptor of SARS-CoV-2, and the kallikrein-kinin-system (KKS). Considerable research interest with respect to COVID-19 treatment is, thus, currently directed towards the components of these systems. In an earlier study, we noticed significantly reduced carboxypeptidase N (CPN, KKS member) activity and partially excessive angiotensin-converting enzyme (ACE, RAS member) activity in the sera of both hospitalized (HoP) COVID-19 patients and a sub-group of covalescent patients, while in the majority of the probands recovering from the disease these values had returned to normal. The data had been obtained using bradykinin (BK) as a reporter peptide, which is a target of both CPN and ACE, and they were supplemented by serum proteomics of the same patient cohort. We hypothesized that the data could be indicative of Long COVID, which had not been fully appreciated at the time of our study.; (2) Methods: The data were re-evaluated in the light of Long COVID. The recent literature on the RAS in COVID-19, antihypertensiva, and Long COVID was briefly reviewed.; (3) Results: While the levels of the BK serum degradation products should return to normal concentrations during convalescence, this was not true for some patients. This could be due to persisting liver problems, because CPN is synthesized there, but also to a dysregulated RAS. This was not reflected in the levels of selected RAS/KKS serum proteins like angiotensinogen (AGT), although AGT correlated with disease severity in HoP. However, standard tests in routine patient care in Long COVID often come back normal, and it may be that BK degradation is specific in some pathophysiologies. Moreover, the HoP group was sub-divided based on the serum protein profiles and COVID-19 severity.; (4) Conclusions: We point out two insights: 1) Sensitive technology such as omics methods might provide unexpected significant differences within the pre-defined patient groups of a clinical study. Those can only be explored, if the cohorts are large enough and properly matched with respect to the parameters known beforehand (e.g., age, gender, co-morbidities). 2) Results of the BK-reporter serum protease activity assay could be indicative of persisting liver problems and/or potentially of Long COVID. Clinical studies are required to test this hypothesis.

When gravity is quantum, the point structure of space-time should be replaced by a non-commutative geometry. This is true even for quantum gravity in the infra-red. Using the octonions as space-time coordinates, we construct a pre-spacetime, pre-quantum Lagrangian dynamics. We show that the symmetries of this non-commutative space unify the standard model of particle physics with $SU(2)_R$ chiral gravity. The algebra of the octonionic space yields spinor states which can be identified with three generations of quarks and leptons. The geometry of the space implies quantisation of electric charge, and leads to a theoretical derivation of the mysterious mass ratios of quarks and the charged leptons. Quantum gravity is quantisation not only of the gravitational field, but also of the point structure of space-time.

It is extremely fascinating and astonishing that the gravitational field on the surface of a neutron star is with a relativistic mass density of 2.65*10¹⁶~5.87*10¹⁸kgm^-3 which can be larger than the mass density of the neutron star (~10¹⁷kgm^-3).Therefore, it is the author’s first intuitional imagining that this field could directly convert into mass. In so strong a gravitational field, electron and proton could be produced directly from graviton–photon collision. The gravitational field exists in everywhere in our universe. No vacuum that the region of a space is “empty” does exist. A particle is clearly always being acted on by the gravitational field. The quantum vacuum fluctuation and vacuum polarization need be re-understood with the interaction between photon and gravitational field. Therefore, the gravitational field is naturally one of the foundations of modern physics.

Renal cell carcinoma (RCC) represents around 3% of all cancers, within which clear cell RCC (ccRCC) are the most common type (70–75%). The RCC disease regularly progresses asymptomatically and upon presentation is recurrently metastatic, so an early method of detection is necessary. The identification of one or more spe-cific biomarkers measurable in biofluids (i.e urine) by combined approaches could surely be appropriate for this kind of cancer, especially due to easy obtainability by non invasive method. OLR1 is a metabolic gene that encodes for the Lectin-like oxidized low-density lipoprotein re-ceptor-1 (LOX-1), implicated in inflammation, atherosclerosis, ROS and metabolic disor-der-associated carcinogenesis. Specifically, LOX-1 is clearly involved in tumor insurgence and progression of different human cancers. This work reports for the first time the presence of LOX-1 protein in ccRCC urine and its peculiar distribution in tumoral tissues. In parallel, urine samples headspace has been analyzed for the presence of the volatile compounds (VOCs) by SPME-GC/MS and gas sensor array. In particular, it was found by GC/MS analysis that 2-Cyclohexen-1-one,3-methyl-6-(1-methylethyl)- correlates with LOX-1 concentration in urine. Thus, the combined approach of VOCs analysis and protein quantification could led to promis-ing results in terms of diagnostic and prognostic potential for ccRCC tumor.

The paper presents an analysis of the method of recording the magnetic component of the Earth’s natural pulse electromagnetic field in an urban environment. This method of recording has already proved itself to be a method that allocates the stressed sections of rock mass at mining and, therefore, authors suppose its effectiveness for allocating active tectonic disturbances and forecasting accidents at underground utilities, what will help reduce the potential environmental hazard of these objects.

Debris-covered glaciers are a notable feature in the greater Himalaya, and their ongoing mass loss under changing climate will affect the water resources of over a billion people. The current knowledge of the mass balance of Himalayan glaciers is restricted by the paucity of in-situ measurements of glaciers in both space and time, as well as the resolution of satellite remote sensing imageries. Recently, the use of Unmanned Aerial System (UAS) imagery has shown the potential to bridge this gap by enabling very detailed monitoring of inaccessible glacial areas. UAS imagery-based monitoring of Himalayan glaciers has so far been limited to a single glacier in the entire Himalaya, providing a limited understanding of spatial variability in glacier mass balance and driving factors. In the first UAS based glacial mass change estimation in the trans-Himalaya, we conducted two Unmanned Aerial System (UAS) surveys (May and November 2019) over the debris-covered Annapurna III glacier in the Himalaya. We performed Structure-from-Motion (SfM) analysis and utilized differential GPS field observations to derive geometrically accurate point clouds, ortho-mosaics and digital surface models (DSMs). The glacial volumetric loss was estimated from DSM differencing, and the magnitude and spatial variability of glacier surface change was derived from 3-D differencing of point clouds. Results revealed a heterogeneous glacial melt pattern, with an average elevation loss of 0.89 m during the monitored time period. The majority of the glacial tongue exhibited surface lowering except the area above and around the glacial snout that surprisingly exhibited significant elevation gain. Both the highest magnitude of mass loss and the highest spatial variability in mass change was observed in areas with exposed ice-cliffs and supraglacial ponds. Glacial surface velocity derived from manual feature tracking showed velocity ranging from 0-4.1 m. A detailed evaluation of specific areas allowed an improved understanding of the complex interplay of factors leading to observed surface change. Our findings expand the extent of UAS based monitoring of debris-covered glaciers in the Himalaya and conclude that UAS derived 3D topographic products will become increasingly important for monitoring of thinning debris-covered glaciers.

Vibrational overtones in deeply bound molecules are sensitive probes for variation of the proton-to-electron mass ratio μ. In nonpolar molecules, these overtones may be driven as two-photon transitions. Here, we present procedures for experiments with O₂⁺, including state-preparation through photoionization, a two-photon probe, and detection. We calculate transition dipole moments between all X²П_g vibrational levels and those of the A²П_u excited electronic state. Using these dipole moments, we calculate two-photon transition rates and AC-Stark-shift systematics for the overtones. We estimate other systematic effects and statistical precision. Two-photon vibrational transitions in O₂⁺ provide multiple routes to improved searches for μ variation.

It is widely believed that the dramatic transformation of the spherical outflows of AGB stars into the extreme aspherical geometries seen during the planetary nebula (PN) phase is linked to binarity and driven by the associated production of fast jets and central disks/torii. The key to understanding the engines that produce these jets and the jet-shaping mechanisms lies in the study of objects in transition between the AGB and PN phases. I discuss the results of our recent studies with high-angular-resolution (with ALMA & HST) and at high-energies (with GALEX, XMM-Newton & Chandra) of several such objects, which reveal new details of close binary interactions and high-speed outflows. These include two PPNe (the Boomerang Nebula and IRAS16342-3814), and the late carbon star, V Hya. The Boomerang is notable for a massive, high-speed outflow that has cooled below the microwave background temperature, making it the coldest object in the Universe. IRAS16342 is the prime example of the class of water-fountain PPNe (very young PPNe with high-velocity H₂O masers) and shows the signature of a precessing jet. V Hya ejects high-speed bullets every 8.5 years associated with the periastron passage of a companion in an eccentric orbit. I discuss our work on AGB stars with strongly-variable high-energy (FUV, X-ray) emission, suggesting that these objects are in the early stages of binary interactions that result in the formation of accretion disks and jets.

Background: Pittosporum tobira (Thunb.) Aiton is an aromatic medicinal plant widely cultivated in the world. However, the essential oils (EOs) from P. tobira flowers for anti-cancer potential is still not systematically studied. The present aim to elucidate the phytochemical composition of the EOs and to explore mechanism of anticancer action. Methods: The EOs were extracted and analyzed by headspace solid-phase microextraction (HS-SPME) with gas chromatography-mass spectrometry (GC-MS). Volatile components were identified according to Kovats retention index (KI) and NIST database. The anti-neoplasm mechanisms of the EOs was comprehensively investigated in lung carcinoma A549 and H460 cells. Results: A total of 47 secondary metabolites representing 94.18% of the EOs were successfully identified: monoterpenes and sesquiterpenes were the dominant terpenoids. The EOs exhibited antiproliferative activity on A549 and H460 lung carcinoma cells. Hoechst 33324 fluorescent staining indicated the typical characteristics of apoptosis and induced cycle phase arrest. AnnexinV/PI staining revealed that the number of apoptotic cells was increased. Furthermore, the EOs also induced the caspase-mediated mitochondrial apoptosis pathway. Conclusions: Findings suggest that the full-scale chemical composition and first characterization of anticancer activities of the EOs, it could be used for integrative natural anti-cancer agents in health care should be pay more attention.

Results-Based Financing (RBF) in pediatrics, in regions with scarce resources like Northern Uganda, provides an innovative approach to enhancing healthcare delivery. RBF aligns financial incentives with desired health outcomes, boosting service quality, efficiency, and effectiveness by tying compensation to achieving specific, measurable health targets. Lacor and Kalongo hospitals, before the introduction of RBF, faced numerous challenges, including limited resources, staffing shortages, and inconsistent quality of care. RBF adoption requires critical health outcomes to target, such as lowering child mortality rates, enhancing vaccination coverage, and increasing the frequency of timely prenatal care visits. The empirical application of RBF in pediatric services at Lacor and Kalongo Hospital from 2018 to 2024 shows improved healthcare quality and outcomes. Healthcare systems can identify ways to implement RBF models better, ensuring that financial incentives effectively contribute to attaining superior health outcomes.

In this study, the fundamentals of electroencephalography signals, their categorization into frequency sub-bands, the circuitry used for their acquisition, and the impact of noise interference on signal acquisition are examined. Additionally, design specifications for medical-grade and research-grade EEG circuits and a comprehensive analysis of various analog front-end architectures for electroencephalograph (EEG) circuit design are presented. Three distinct selected case studies are examined in terms of comparative evaluation with generic EEG circuit design templates. Moreover, a novel one-channel battery-supplied EEG analog front-end circuit designed to address the requirements of usage protocols containing strong com-pound muscle movements is introduced. Furthermore, a realistic input signal generator circuit is proposed that models the human body and the Electromagnetic Interference from its surroundings. Experimental simulations are conducted in 50 Hz and 60 Hz electrical grid environments to evaluate the performance of the novel design. The results demonstrate the efficacy of the proposed system, particularly in terms of bandwidth, portability, common mode rejection ratio , gain, suppression of muscle movement artifacts, electrostatic discharge and leakage current protection. Conclusively, the novel design is cost-effective and suitable for both commercial and research single-channel EEG applications. It can be easily incorporated in Brain Computer Interfaces and neurofeedback training systems.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

It’s well known that existing horizontal well drilling and hydraulic fracturing technology that is used to achieve large-scale cost-effective production from immature to low-moderate maturity continental shale in China, where the organic matter mainly exists in the solid form is fairly ineffective. To overcome the obstacles, in-situ conversion technology seems feasible, while implementing it in the target layer along with estimating the amount of expected recoverable hydrocarbon in such shale formations seems difficult. This is because there is no guideline to choose the most appropriate method and select relevant key parameters for this purpose. Hence, based on thermal simulation experiments during the in-situ conversion of crude oil from the Triassic Chang 73 Formation in the Ordos Basin and the Cretaceous Nenjiang Formation in the Songliao Basin, this deficiency in knowledge was addressed. First, relationships between the in-situ converted total organic carbon (TOC) content and the vitrinite reflectance (Ro) of the shales and between the residual oil volume and the hydrocarbon yield was established. Second, the yields of residual oil and in-situ converted hydrocarbon were measured, revealing their sensitivity to fluid pressure and crude oil density. In addition, a model was proposed to estimate the amount of in-situ converted hydrocarbon based on the TOC, hydrocarbon generation potential, Ro, residual oil volume, fluid pressure, and crude oil density. Finally, a method was established to determine key parameters on the final hydrocarbon yield from immature to low-moderate maturity organic material during in-situ conversion in shales. Following the procedure outlined in this paper, estimated recoverable in-situ converted oil in the shales of the Nenjiang Formation in the Songliao Basin was estimated to be approximately 292×108 tons, along with 18.5×1012 cubic meters of natural gas, in an area of approximately 8×104 square kilometers. Collectively, the method developed in this study is independent from the organic matter type and other geological and/or petrophysical properties of the formation and can be applied to other areas globally where there isn’t any available in-situ conversion thermal simulation experimental data.

An imbalance between production and excretion of amyloid β peptide (Aβ) in the brain tissues of Alzheimer’s disease (AD) patients leads to Aβ accumulation and formation of noxious Aβ oligomers/plaques. A promising approach to AD prevention is reduction of free Aβ level by directed enhancement of Aβ binding to its natural depot, human serum albumin (HSA). We previously demonstrated the ability of specific low-molecular-weight ligands (LMWLs) of HSA to improve its affinity for Aβ. Here we develop this approach by bioinformatic search for the clinically approved AD-related LMWLs of HSA, followed by classification of the candidates according to the predicted location of their binding sites on HSA surface, ranking of the candidates, and selective experimental validation of their impact on HSA affinity for Aβ. The top 100 candidate LMWLs were classified into the five clusters. The specific representatives of the different clusters exhibit dramatically different behavior, with 3- to 13-fold changes in equilibrium dissociation constants for the HSA-Aβ40 interaction: prednisone favors HSA-Aβ interaction, mefenamic acid shows the opposite effect, while levothyroxine exhibits the bidirectional effects. Overall, the LMWLs of HSA chosen here provide a basis for drug repurposing for AD prevention, and for search for the medications promoting AD progression.

The lung microbiota is a complex community of microorganisms that colonize the respiratory tract of individuals from or even before birth. Although the lungs were traditionally believed to be sterile, recent research has shown that there is a diversity of bacterial species in the respiratory system. Knowledge about the lung microbiota in the newborn and its relationship with bacterial infections is of vital importance to understand the pathogenesis of respiratory diseases in neona-tal patients undergoing mechanical ventilation. In this article, the current evidence on the compo-sition of the lung microbiota in the newborn will be reviewed, as well as its role in the develop-ment of bacterial infections in mechanically ventilated neonates. Although advances in many as-pects of the neonatal intensive care unit care have significantly improved the survival of preterm infants, the diagnosis and treatment of ventilator-associated pneumonia has not progressed in recent decades. Avoiding dysbiosis caused by inappropriate use of antibiotics around birth, as well as avoiding intubation of patients or promoting early removal of endotracheal tubes are among the most important preventive measures for ventilator-associated pneumonia. The use of probiotics and prebiotics to prevent infectious, allergic or metabolic complications in the short or long term constitutes a very important field of research in perinatal medicine.

In space application, hybrid pixel detectors of the Timepix family have been considered mainly for measurement of radiation levels and radiation dosimetry in low earth orbits. By the example of the Space Application of Timepix Radiation Monitor (SATRAM), we demonstrate the unique capabilities of Timepix-based miniaturized radiation detectors for particle separation. Using a novel method for proton spectrum reconstruction, we were able to measure the spectrum of protons trapped in the inner Van-Allen radiation belt, for the first time with a single-layer detector. We assess the measurement stability and the resiliency of the detector to the space environment demonstrating that, even though degradation is observed, data quality has not been affected significantly over more than 10 years. Based on the SATRAM heritage and the capabilities of the latest-generation Timepix-series chips, we discuss their applicability for use in a compact magnetic spectrometer for deep-space mission or in the high radiation environment of the Jupiter radiation belts, and their capability for use as single-layer X- and γ-ray polarimeter. The latter was supported by measurement of the polarization of scattered radiation in a laboratory experiment, where a modulation of 80% was found.

This study aimed to evaluate the proliferation and migration of fibroblast cells derived from chronic wounds and investigate the impact of low-level laser therapy (LLLT) on their growth and migration. A total of 60 dermal samples were obtained from three sites of chronic pressure ulcers and diabetic ulcers in 20 patients. Following collection in the operating room, the dermal samples were isolated using the procedure described by Freshney RI. Fibroblasts from the wound base (Site 1) exhibited a slow proliferation rate and a decrease in proliferative capacity. Fibroblasts from wound margins (Site 2) and adjacent healing skin (Site 3) could be successfully isolated and maintained for multiple generations without any morphological changes. Fibroblasts from chronic wounds at Sites 2 and 3 showed slower proliferation rates and reduced migration capabilities compared to normal dermal fibroblasts (control samples). The fibroblast cells were exposed to LLLT at different energy levels (2.5, 3, and 3.5 J/cm2). The laser-treated groups demonstrated a significantly higher increase in cell count compared to the control sample, with the highest increase observed at an energy level of 3 J/cm2. These findings suggest that LLLT at an energy level of 3 J/cm2 could effectively enhance fibroblast migration, indicating its potential as a therapeutic intervention for chronic wounds.

Machine Learning can be used for social good. In this paper, we discuss how it can be used to combat climate change and facilitate land management and farming in developing countries and in particular in Côte d’Ivoire. This paper explores models that improve land and water management and agricultural farming cultivation to contrast climate change. Côte d’Ivoire is the largest producer of cocoa beans (43%) in the world, but deforestation, lack of rainfall, drought, and climate change threaten crops and the already fragile economy of Ivorian farmers. It is important to combat climate change with methods and techniques that are affordable to the local farmers and also induce positive effects in production. We discuss the use of low-cost sensors to collect data on the soil and open data and open source software to develop AI tools. We show that using deep neural networks (YOLOv5m) is effective for detecting healthy plants and pods of cocoa from damaged ones only using mobile phone images. Focusing on a single land is not enough to combat climate change, which has different causes and involves also knowledge at a higher scale. We propose a new method of forecasting for the analysis of remote sensors. Remote sensor data come from GRACE NASA Mission and ERA5 produced by the Copernicus Climate Change Service at ECMWF. We implement a new deep neural network architecture named CIWA-net. It is based on a Fully Convolutional Neural Network (FCN) [ 1] and it is a U-net like architecture [2]. The aim of CIWA-net is to forecast Total Water Storage Anomalies (TWSA). We show the quality of our model with a comparison to a vanilla Convolutional Neural Network. CIWA-net could be used also for the detection of lands that interfere with agricultural work and yields, such as deserted areas, water-soaking soil areas, zones at risk of desertification, and poor land use. The employment of AI at the service of agriculture can decrease crop losses and waste, lower the inputs onto the soil of fertilizers, responsible for the increase of Greenhouse Gases. It could be useful to help the small farmers (at a local scale) and also the policy-makers and farmers’ cooperatives (at the regional scale) to take valid and coordinated countermeasures to improve the correct use of the lands, helping to contrast and adapt to climate change.

Osteoporotic spinal fractures represent an increasingly widespread health problem in our aging society. We aimed to investigate the treatment options for low-energy spinal fractures in the el-derly and their impact on mortality, focusing on surgical stabilization using minimally invasive and open techniques. We evaluated 1356 patients over 50 years of age with compression frac-tures sustained due to low energy trauma treated at a single trauma center. We compared the mortality of patients following stable and operated/non-operated unstable compression frac-tures and the eligibility to surgery using the open and minimally invasive approach. The pa-tients received surgical or conservative care according to severity and eligibility to surgery. The mortality hazard ratio of patients who underwent screw fixation was 1.02 (P > .91), of patients who refused surgery was 1.68 (P < .001) and that of patients with anesthesiological contraindica-tion was 1.57 (P = .08), compared to conservatively treated patients with stable fractures. The dif-ference in mortality between open and minimally invasive surgeries was not significant, but the number of patients eligible for surgery with the minimally invasive procedure was significantly higher (OR: 0.25; P < .001). Spinal stability after fractures may be an important predictor of sur-vival in patients with low-impact fractures.

Functional gastrointestinal disorders (FGIDs) are common in children and adolescents. In recent years, interest in the role of diet in the treatment of FGIDs has increased. Currently, interest focus-es on the low-FODMAP diet (LFD), the fructose- or lactose-restricted diet (FRD or LRD), the glu-ten-free diet (GFD), and the Mediterranean diet (MD). In this review, we focus on the role of these dietary patterns in the FGIDs most commonly diagnosed in clinical practice, namely irritable bowel syndrome (IBS), functional abdominal pain (FAP), functional dyspepsia (FD), and func-tional constipation (FC). Fifteen clinical trials were systematically reviewed (both RCTs and sin-gle arm clinical trials). We demonstrated the lack of high-quality intervention trials. Based on current evidence, low-FODMAP diet, LRD, FRD, or GFD have no place in daily practice for the management of children and adolescents with FGIDs. Nevertheless, some patients with IBS or RAP may have some benefit from the use of a low-FODMAP diet or FRD/LRD. Limited data sug-gest that MD may be promising in the management of FGIDs, especially in IBS patients, but more data are required to investigate the mechanisms of its protective effects.

Background: In regenerative dentistry the graft material influences the success. It should act as an osteoconductive scaffold, providing a mineral substrate during resorption and inducing the activity of osteoinductive cells capable of producing new bone, platelet growth factors, and cell differentiation factors inducing the differentiation of undifferentiated mesenchymal cells into. Given that dentin shares many biochemical characteristics with bone tissue, it has recently attracted considerable interest as a biomaterial for bone repair. The aim of this study is to compare two grinder types in order to determine the optimal method for producing dentinal particles using a mechanical grinder. Materials and methods: A sample of 40 natural human teeth without restorations, prostheses or root canal treatments was used and divided into two groups subjected to two different grinder speeds (high-speed and low-speed). The high-speed showed a greater dispersion (53.5+-9.89% of the tooth) due to the pulverisation (highly thin granules) of part of the tooth. The low-speed grinder does not pulverize the dentin and the percentage of tooth loss is 9.16+/-2.34%. Conclusion: The low-speed gringer allows to save a major part of the tooth and to have a maximum quantity of graft material but requires more time. Further studies must be promoted to optimise the grinding procedures.

This research proposes a roof-mounted auxiliary power supply (APS) system for 600VDC low-floor light rail vehicle (LRV). The proposed APS system consists of five parallel-connected dc-ac inverter modules (modules 1-5). The inverter modules 1 and 2 are three-phase dc-ac inverters for compressor motors of the cooling system, and the inverter modules 3 and 4 are three-phase dc-ac inverters for air pump motors of the braking system. The inverter module 5 is single-phase dc-ac inverter for 220VAC power supply for onboard electric loads. Simulations and experiments were carried out under variable load torque and output frequency for modules 1 – 4; and under full and no resistive loads for the inverter module 5. The measured total input current and total input power of the proposed APS system under full load condition are 118.76A and 71.25kW. Essentially, the proposed APS system is operationally applicable to the 600VDC low-floor RLV. Besides, the novelty of this research lies in the use of five parallel-connected inverter modules, unlike in the conventional APS systems which require three-phase output transformer or isolated dc-dc converter. Specifically, the proposed APS system requires neither three-phase output transformer nor isolated dc-dc converter.

Maternal and child nutrition has been a critical component of health, sustainable development, and progress in low- and middle-income countries (LMIC). While a decrement in maternal mortality is an important indicator, simply surviving pregnancy and childbirth does not imply better maternal health. One of the fundamental obligations of nations under international human rights law is to enable mothers and teenage girls to endure pregnancy and delivery as an aspect of their enjoyment of reproductive and sexual health and rights and live a dignified life. The aim of this study was to discover the correlation between the Maternal Observation and Motivation (MOM) program and m-Health support for maternal and newborn health. A Comparative study was done among 109 pregnant mothers (study group-94; control group-102 mothers) with not less than 20 weeks of gestation. Maternal outcomes such as Hb, weight gain and newborn results like birth weight and crown- heel length was obtained on the baseline, 28 and 36 weeks of gestation. Other secondary data collected were abortion, stillbirth, low birth weight, major congenital malformations, twin or triplet pregnancies, physical activity and maternal wellbeing. The MOM intervention included initial face to face education, three in-person visits and eight virtual health coaching by WhatsApp. The baseline data on Hb of the mothers show that 31(32.98%) vs 27(28.72%) of the study and control group had anaemia, which improved to 27.66% and 14.98% among study group mothers at 28 and 36 weeks of gestation (p<0.001). The weight gain (p< 0.001), level of physical activity (p< 0.001), and maternal wellbeing (p< 0.01) also had significant differences after the Intervention. Even after controlling for potentially confounding variables, the maternal food practices regression model revealed that birth weight was directly correlated with consumption of milk (p 0.001), fruits (p 0.01), and green vegetables (p 0.05).As per the physical activity and maternal wellbeing regression model, the birth weight and crown heel length were strongly related with the physical activity and maternal wellbeing of mothers at 36 weeks of gestation (p <0.05). Combining the MOM intervention with standard antenatal care is a safe and effective way to improve maternal welfare while upholding pregnant mothers' human rights.

Recent progress in deep learning has led to accurate and efficient generic object detection networks. Training of highly reliable models depends on large datasets with highly textured and rich images. However, in real-world scenarios, the performance of the generic object detection system decreases when (i) occlusions hide the objects, (ii) objects are present in low-light images, or (iii) they are merged with background information. In this paper, we refer to all these situations as challenging environments. With the recent rapid development in generic object detection algorithms, notable progress has been observed in the field of object detection in challenging environments. However, there is no consolidated reference to cover state-of-the-art in this domain. To the best of our knowledge, this paper presents the first comprehensive overview, covering recent approaches that have tackled the problem of object detection in challenging environments. Furthermore, we present the quantitative and qualitative performance analysis of these approaches and discuss the currently available challenging datasets. Moreover, this paper investigates the performance of current state-of-the-art generic object detection algorithms by benchmarking results on the three well-known challenging datasets. Finally, we highlight several current shortcomings and outline future directions.

In France, the regional airport’s demand for services is facing challenges due to the continuous expansion of the high-speed train, high-speed line, and highway networks. This study focuses on the viability of regional airports in France through technical efficiency using data envelopment, principle component analysis, Malmquist productivity index, and regression analysis using bootstrapping. To face the current competitive environment, the regional airports in France adopted strategies, such as the construction of low-cost carrier (LCC) dedicated terminals (LCCTs) with lower expenses to attract more LCCs, increasing non-aeronautical revenue, and hosting regional hubs of LCCs. This is the first study that analyzes all of the French regional airports. The findings indicate that the existence of LCCTs positively affects technical efficiency on the airport’s performance, and share of LCCs at a regional airport leads to neither the efficiency nor the profit level.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

The bivalve mollusc Pinna nobilis, endemic to the Mediterranean Sea, since 2016 is vanishing from the whole basin because of an infection by multiple pathogens that caused mass mortality events. In the Eastern Mediterranean some little populations seem to be resistant to the infection. These individuals could represent the only possibility for the species to recolonize now desert habitats. Thus, according to the recommendations of IUCN, the looking for living specimens of P. nobilis is a priority. As a result of a monitoring activity carried out in 2022-2024, along the Ionian cost of Apulia, in Southern Italy, the species has completely disappeared leaving only empty shells. Concurrent to the vanishing of P. nobilis, its congeneric P. rudis, resistant to the infection, seems to be taking advantage, becoming more common and colonizing habitats once exclusive of P. nobilis. In fact, from different areas of the Mediterranean, the sightings of P. rudis are increasing, together with the discovering of individuals exhibiting morphological traits that are a mixing between the two species. In some cases, these morphological features are not easy to detect, anyway the presence of these hybrids, resistant to the infection, is important for the conservation of the species.

This paper revisits the analytical theory of fractional vibrations with the highlights in five aspects. First, we address the cases of structures with frequency dependent mass or damping or stiffness in Sections 2-4. Second, we introduce the theory based on the general second-order vibration motion equation with frequency dependent elements (mass, damping, stiffness) in Sections 5-7. Third, we present the analytical theory of seven specific classes of second-order vibration systems with frequency dependent mass or damping or stiffness in Sections 8 and 9. Fourth, we bring forward the analytical theory of seven classes of fractional vibration systems in Sections 10-12. Finally, as an application, we give the closed form expression of the forced response to multi-fractional Euler-Bernoulli beam in Section 13. The explanation of the nonlinearity of fractional vibrations is given in Section 14.

FLH 13-11 is an F1 interspecific hybrid muscadine grape genotype that was developed to produce new anthocyanins for pigment color stability. This hybrid resulted from a cross between ‘Marsh’ (Vitis munsoniana) and ‘Magoon’ (V. rotundifolia). This report characterizes the anthocyanins produced in fully ripe berries, and reveals a significant difference in total anthocyanin contents from two continuous cropping seasons. High-performance liquid chromatography with a diode array detector (HPLC-DAD) and HPLC-quadrupole time-of-flight tandem mass spectrometry (HPLC-qTOF-MS/MS) were used to profile anthocyanins in berries. The resulting data showed that fourteen anthocyanins were detected, six from 2011 and nine from 2012, with only one produced in both seasons. However, the anthocyanidin profiles of berries were the same. Five anthocyanins were annotated as diglucosides of anthocyanidins based on MS/MS features, including delphinidin 3,5-diglucoside produced in both seasons, cyanidin 3,5-diglucoside mainly formed in 2011, petunidin 3,5-diglucoside, malvidin 3,5-diglucoside, and peonidin 3,5-glucoside only detected in 2012. Also, three anthocyanidin-diglucoside like anthocyanins and three monoglucosides including peonidin 3- glucoside, delphinidin 3- glucoside like, and pelargonidin 3- glucoside like anthocyanins, were detected in 2011 and 2012, respectively. These results indicate that FLH 13-11 can produce both anthocyanidin-diglucosides and -monoglucosides, and their biosynthesis is closely dependent on cropping years.

In the last two decades, the development of high-throughput diagnostic methods and availabil-ity of effective treatments has increased interest in newborn screening for lysosomal storage disorders. However, long-term follow-up experience is needed to clearly identify risks, benefits and challenges. We report our 8-year experience of screening and follow up on about 250,000 neonates screened for four lysosomal storage diseases (Pompe disease, mucopolysaccharidosis type I, Fabry dis-ease, Gaucher disease), using enzyme activity assay by tandem mass spectrometry, and bi-omarker quantification as second tier test. Among the 126 positive newborns (0.051%), 51 infants were confirmed as affected (positive pre-dictive value 40%), with an overall incidence of 1:4,874. Of these, 3 infantile-onset Pompe dis-ease, 2 neonatal-onset Gaucher disease and 4 mucopolysaccharidosis type I patients were imme-diately treated. Furthermore, another four Gaucher disease patients needed treatment in the first years of life. Our study demonstrated the feasibility and effectiveness of newborn screening for lysosomal storage diseases. Early diagnosis and treatment allow the achievement of better patient out-comes. Challenges such as false positive rates, the diagnosis of variants of uncertain significance or late-onset forms, and the lack of treatment for neuronopathic forms, should be addressed.

Background: The manifestations, severity, and mortality of COVID-19 are considered to be associated with the changes in various hematological parameters and in immunity. Associations of immunoglobulin G antibodies against severe acute respiratory syndrome-linked coronavirus (IgG-SARS)-positive status with cardiac function and hematological and biochemical parameters in apparently health subjects are poorly understood. Methods: The present cross-sectional study included 307 healthy volunteers (24-69 years of age; 44.8±8.6 years; 80.4% men) and was initiated in 2019 before the COVID-19 pandemic. COVID-19 episodes were confirmed by detection of IgG-SARS against SARS-CoV-2 S1 RBD to reveal 70 IgG-SARS-positive and 237 negative participants. Numerous ultrasound characteristics were assessed by echocardiography, and 15 hematological and biochemical parameters were assayed in the blood. Descriptive and comparative analysis was based on the IgG-SARS status of the participants. Results: The left ventricular mass index, mitral ratio of peak early to late diastolic filling velocity or flow velocity across the mitral valve, and deceleration time of early mitral inflow were decreased (P<0.05) in IgG-SARS-positive participants versus those in IgG-SARS-negative participants according to multivariate logistic regression analysis. Erythrocyte sedimentation rate and platelet count were slightly increased, and blood hemoglobin was decreased in IgG-SARS-positive participants compared with those in IgG-SARS-negative participants. Conclusions: LV filling, inflammation, blood coagulation, and hemoglobin appear to be influenced by COVID-19 infection in healthy participants. These observations contribute to the development of a population recovery strategy after the episodes of COVID-19.

The article considers an internal boundary value problem of the distribution of an electrostatic field in a lens formed by two identical semi-infinite circular cylinders coaxially located inside an infinite external cylinder. The problem is reduced to solving a system of singular Wiener-Hopf integral equations, which is further solved by the Wiener-Hopf method using factorized Bessel functions. Solutions to the problem for each region inside the infinite outer cylinder are presented as exponentially converging series in terms of eigenfunctions and eigenvalues.

During the SARS-CoV-2 pandemic, many virus-binding monoclonal antibodies have been developed for clinical and diagnostic purposes. This underlines the importance of antibodies as universal bioanalytical reagents. However, little attention is given to the reproducibility crisis that scientific studies are still facing to date. In a recent study, not even half of all research antibodies mentioned in publications could be identified at all. This should spark more efforts in the search for practical solutions for the traceability of antibodies. For this purpose, we used thirty-five monoclonal antibodies against SARS-CoV-2 to demonstrate how sequence-independent antibody identification can be achieved by simple means applied onto the protein. First, we examined the intact and light chain masses of the antibodies relative to the reference material NIST-mAb 8671. Already half of the antibodies could be identified based solely on these two parameters. In addition, we developed two complementary peptide mass fingerprinting methods with MALDI-TOF-MS that can be performed in 45 minutes and had a combined sequence coverage of over 80%. One method is based on the partial acidic hydrolysis of the protein by 5 mM of sulfuric acid at 99 °C. Furthermore, we established a fast way for a tryptic digest without an alkylation step. We were able to show that the distinction of clones is possible simply by a brief visual comparison of the mass spectra. In this work, two clones originating from the same immunization gave the same fingerprints. Later, a hybridoma sequencing confirmed the sequence identity of these sister clones. In order to automate the spectral comparison for larger libraries of antibodies, we developed the online software ABID 2.0 (https://gets.shinyapps.io/ABID/). This open-source software determines the number of matching peptides in the fingerprint spectra. We propose that publications and other documents critically relying on monoclonal antibodies with unknown amino acid sequences should include at least one antibody fingerprint. By fingerprinting an antibody in question, its identity can be confirmed by comparison with a library spectrum at any time and context.

The article is focused on detailed framework process for hierarchized construction of periodic freight train paths (PFTPs) – allocation of pre-arranged railway capacity to freight rail operators. The framework process considers fluctuations in demand for capacity from freight rail opera-tors, so the quality of a freight train path is related with its construction priority. Introduced framework process aims to offer freight rail operators attractive train paths, with low number of scheduled stops, and this way enhance competitiveness and decrease energy consumption of freight railway as a factor for sustainable development. The proposed generic process is in-tended for all time horizons of capacity allocation. Correctness of the framework process is tested on the example of mainline Prague – Dresden, in the context of prospective (denser) mod-el passenger timetable.

Metandienone and methyltestosterone are orally active anabolic-androgenic steroids with a 17α-methyl structure that are prohibited in sports but are frequently detected in anti-doping analysis. After the previously reported detection of long-term metabolites with a 17ξ-hydroxymethyl-17ξ-methyl-18-nor-5ξ-androst-13-en-3ξ-ol structure in the chlorinated metandienone analog dehydrochloromethyltestosterone (“Oral Turinabol”), in this study we investigated the formation of similar metabolites of metandienone and 17α-methyltestosterone with a rearranged D-ring and a fully reduced A-ring. Using a semi-targeted approach including synthesis of reference compounds, two diastereomeric substances, viz. 17α-hydroxymethyl-17β-methyl-18-nor-5β-androst-13-en-3α-ol and its 5α-analog, were identified following an administration of methyltestosterone. In post-administration urines of metandienone, only the 5β-metabolite was detected. Additionally, 3α,5β-tetrahydro-epi-methyltestosterone was identified in the urines of both administrations besides the classical metabolites included in the screening procedures. Besides their applicability for anti-doping analysis, the results provide new insights on the metabolism of 17α-methyl steroids with respect to the order of reductions in the A-ring, the participation of different enzymes, and alterations of the D-ring.

Space-time evolution is briefly explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (mass), charges and absolute time are newly defined based on the 4-D Euclidean space. The photons and gravitons are understood as the 2-D space fluctuations along the space axes and 1-D time fluctuations along the time axis, respectively. This indicates that the electromagnetic (EM) and gravitational (G) waves can be unified into the so called gravityelectromagnetic (GEM) wave which has both space and time fluctuations. The photon with zero force fields is the 2EM wave because an EM wave corresponds to a charged fermion. The dark matter bosons, weak force bosons, strong force bosons are the 1-D time fluctuations which can be expressed by the G waves. This indicates that all five forces are unified by the GEM wave. It is called as the super unification theory in the present work. And the force carrying bosons and mesons are, for the first time, proposed as the possible candidates of the magnetic monopoles like the fermions and baryons are the electric monopoles. The signs of the magnetic charges quantized as q_m=cq are newly defined. The big bang is understood by the space-time evolution of the 4-D Euclidean space but not by the sudden 4-D Minkowski space-time creation. The big bang process created the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry.

The world is moving to the next phase of the energy transition with high penetrations of renewable energy. Flexible and scalable redox flow battery (RFB) technology is expected to play an important role in ensuring electricity network security and reliability. Continuous performance improvements will further enhance their value by reducing parasitic losses and maximizing available energy conversion over broader operating conditions. Concentration overpotentials from poor internal reactant distribution at high and low states of charge (SOC) limit power densities and are thus an important area of investigation. However, efforts to address these coupled electrochemical phenomena can compromise mechanical performance. Modelling and simulation of cell design innovations have shown it is possible to reduce losses from pump energy while increasing the availability of active species where required. The combination of wedge-shaped cells with static mixers investigated in this paper can reduce pressure drop and improve energy efficiency. Toroidal vanadium redox flow battery (VRB/VRFB) designs incorporating this innovation are presented for further development to improve community engagement with the technology.

Tissue engineering has the potential for repairing large bone defects, which impose a heavy financial burden on the public health. However, difficulties with O₂ delivery to the cells residing in the interior of tissue engineering scaffolds make it challenging to grow artificial tissues of clinically-relevant sizes. This study uses image-based simulation in order to provide insight into how to better optimize the scaffold manufacturing parameters, and the culturing conditions, in order to resolve the O₂ bottleneck. To do this, high resolution 3D X-ray images of two common scaffold types (salt leached foam and non-woven fiber mesh) are fed into a Lattice Boltzmann Method fluid dynamics and reactive Lagrangian Scalar Tracking mass transfer solvers. The obtained findings indicate that the scaffolds should have maximal surface area-to-solid volume ratios, for higher chances of the molecular collisions with the cells. Furthermore, the cell culture media should be flown through the scaffold pores as fast as practically possible (without detaching or killing the cells). Finally, we have provided a parametric sweep that maps how the molecular transport within the scaffolds is affected by variations in rates of O₂ consumption by the cells. Ultimately, the results of this study are expected to benefit the computer-assisted design of tissue engineering scaffolds and culturing experiments.

Management of resistant Tuberculosis (TB) can be extremely difficult, especially in case of novel unpredicted complications. In this report, we present a case of a 48-year-old patient with pre-extensive-drug-resistant-(XDR)-TB who received a treatment regimen including Pretomanid, Bedaquiline, Linezolid, Cycloserine and Amikacin and died due to myocarditis. Acquired resistance to first- and second-line drugs developed due to previous poor adherence to medication. The clinical presentation of the patient, along with her initial ultrasonographical, electrocardiogram (ECG) and laboratory examinations, were typical for acute myocarditis, however, the patient was considered unstable and further investigation with Magnetic Resonance Imaging (MRI), pericardiocentesis and endomyocardial biopsy were not performed. To our knowledge, this is the first case of myocarditis in such a patient, the clinical features of which set a high suspicion of drug-induction that could be attributed to the treatment regimen that was administered. Clinicians who manage cases of drug-resistant TB should be aware of this, newly reported, potentially lethal, adverse event.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

This article presents a unique set of voltage and current data from a public building and acquired using a hybrid measurement solution that combines Python and Grafana. The transversal purpose consists of contributing to the community with a vision of the quality of the supply more oriented to the monitoring of the state of the network, providing a more realistic vision, which allows a better understanding, and the adoption of the best decisions to achieve the efficient energy management and thus optimize the operation and maintenance of power systems. The work focuses on higher order statistical estimators that, combined with exploratory data analysis techniques, improve the characterization of the shape of the stress signal. These techniques and data, together with the acquisition and monitoring system, present a unique combination in the line of low-cost measurement solutions. It also incorporates the underlying benefit of the contribution to industrial benchmarking. The paper also includes a computational comparison between Python and LabVIEW to elicit the performance of the measurement solution.

The most popular schemes of digital potentiometers (DP) and digital-to-analog converters (DAC) are considered. DP and DAC use how elements of parameter adjustment of active RC-filters. The circuits of the DAC on the Kelvin-Varley divider, the Kelvin divider based on the R-2R matrix, and the architecture of the DAC with a segmented circuit are shown. The internal structure of DP an Analog Devices and Intersil company is shown, and also the DP switching circuits in a tunable low-pass filter and a band-pass filter, a programmable inverting amplifier and a voltage regulator are presented.

To understand great disparities in disease outcomes between CIVID-19 patients, we explore infection and host responses in kinetics. From existing data, we deduced a model that the lungs are damaged by rapidly rising flow resistance as a result of retaining white blood cells in lung tissues. The retention of white blood cells is initially triggered by viral infection but aggravated by injuries caused by low temperature. Lungs are initially damaged by fluid leakage, rapidly followed by extruding blood into alveolar spaces. The step of blood extruding is predicted to take place in a very short time. Our simulations show that as little as 0.1% retention of white blood cells in the lungs can lead to their failure in 5 to 10 days. The small degrees of imbalance implies that this imbalance could be corrected by a large number of factors that are known to reduce flow resistance. The model implies that the top priority is maintaining blood micro-circulation and preserving organ functions in the entire disease course, especially after the virus has spread the whole lungs. From exploring a large number of hypothetical infection modes, we propose preventive, mitigating and treatment strategies for ultimately ending the pandemic. The first strategy is avoiding exposures that could result in widespread damages to lungs and taking post exposure mitigating measures that would reduce disease severity. The second strategy is reducing death rate and disability rate from the current levels to one tenth for infected patients by using multiple factors health optimization method. The double reduction strategies are expected to generate a series of chain reactions that favor mitigating or ending the pandemic. Some reactions include a big reduction of the amount of viral discharges from infected patients into the air, the avoidance of panic, chronic stress and emotional distress, and cross-infections which are expected in quarantines. The double reductions would have a final effect of ending the pandemic.

Given the high number of vehicle-crash victims, it has been established as a priority to reduce this figure in the transportation sector. For this reason, many of the recent researches are focused on including control systems in existing vehicles, to improve their stability, comfort and handling. These systems need to know in every moment the behavior of the vehicle (state variables), among others, when the different maneuvers are performed, to actuate by means of the systems in the vehicle (brakes, steering, suspension) and, in this way, to achieve a good behavior. The main problem arises from the lack of ability to directly capture several required dynamic vehicle variables, such as roll angle, from low-cost sensors. Previous studies demonstrate that low-cost sensors can provide data in real-time with the required precision and reliability. Even more, other research works indicate that neural networks are efficient mechanisms to estimate roll angle. Nevertheless, it is necessary to assess that the fusion of data coming from low-cost devices and estimations provided by neural networks can fulfill the reliability and appropriateness requirements for using these technologies to improve overall safety in production vehicles. Because of the increasing of computing power, the reduction of consumption and electric devices size, along with the high variety of communication technologies and networking protocols using Internet have yield to Internet of Things (IoT) development. In order to address this issue, this study has two main goals: 1) Determine the appropriateness and performance of neural networks embedded in low-cost sensors kits to estimate roll angle required to evaluate rollover risk situations. 2) Compare the low-cost control unit devices (Intel Edison and Raspberry Pi 3 Model B), to provide the roll angle estimation with this artificial neural network-based approach. To fulfil these objectives an experimental environment has been set up composed of a van with two set of low-cost kits, one including a Raspberry Pi 3 Model B, low cost Inertial Measurement Unit (BNO055 - 37€) and GPS (Mtk3339 - 53€) and the other having an Intel Edison System on Chip linked to a SparkFun 9 Degrees of Freedom module. This experimental environment will be tested in different maneuvers for comparison purposes. Neural networks embedded in low-cost sensor kits provide roll angle estimations very approximated to real values. Even more, Intel Edison and Raspberry Pi 3 Model B have enough computing capabilities to successfully run roll angle estimation based on neural networks to determine rollover risks situation fulfilling real-time operation restrictions stated for this problem.

Based on three assumptions of our 4G model of final unification, we have developed simple logics for estimating the unified atomic mass unit, atomic electrochemical equivalents, Faraday constant and Avogadro number. We appeal the science community to review the following points. 1) Unified atomic mass or energy unit can be considered as ‘average rest energy of nucleons minus average binding energy per nucleon of all atomic nuclides plus electron rest energy’. 2) Electrochemical equivalent of any atomic ion is nothing but the ratio of its mass to its charge. 3) Faraday charge is nothing but the ratio of elementary charge to unified atomic mass unit. 4) Faraday mass can be considered as the inverse of Faraday charge. 5) Avogadro number is nothing but the inverse of unified atomic mass unit. 6) Number of atoms per kg can be called as Kg-mole and number of atoms per gram can be called as gram-mole. Following our 4G model, starting form A=5 to 340, for isobars, ‘average binding energy per nucleon’ having maximum binding energy can be estimated with a simple relation of the form, BE/A=A^-1[1-(0.5+0.000935A²)-A^1/3]10.1MeV. It needs a review and fine tuning.

This paper examines some of the largely neglected areas of opportunity to utilize skeletal space structure systems in support of modular, industrialized, economical, sustainable and digital future of the construction industry. In this context, the feasibility of future use of skeletal space structures is studied for a few classes of engineering structures, namely, residential apartment buildings, and offshore platforms, along with their suitability for reconstruction, renovation, modernization and retrofit of damaged buildings and urban areas of cultural heritage significance. Finally, the particulars of lean project management of space structures are discussed with emphasis on engineering and economic factors, production management, environmental aspects, quality management, and reliability, maintainability and sustainability considerations. This article concludes that skeletal space structures can fulfil many of the essential construction requirements of modern societies, especially those facing environmental challenges, all while allowing for design flexibility and mass customization.

Our matter universe is made up of four components of dark energy (DE), dark matters (DMs), leptons and quarks which are created from the decay of the primary black hole through the inflation after big bang. In the three-dimensional quantized space model, the sum (DER) of the dark energy (DE) and radiations (R) is the flat photon space and there are 39 particles of 3 dark matters, 9 leptons and 27 quarks. Generally speaking, the mass ratio of the quarks with the 27 particles is smallest and the mass ratio of the DER photon space with the 1 massless photon is largest. Therefore, the mass ratios of DER, DMs, leptons and quarks are inversely proportional to the particle numbers of DER, DMs, leptons and quarks as the first assumption. This simple rule is called as the universe mass ratio golden rule in Fig. 12. This simple rule is successfully applied to the observed mass ratios of the Planck and WMAP missions. The best particle number combination (1, 3, 9, 27) of the four components (DER, DMs, Leptons, Quarks) to explain the Planck 2018 and WMAP results is the same as the particle number combination (1, 3, 9, 27) of the 3-dimensional quantized space model. The calculated mass ratios of DER, DMs, leptons and quarks are 67.5 %, 22.5 %, 7.5 % and 2.5 %, respectively. And the calculated mass ratios of neutrinos and ordinary matters are 5.0 % and 5.0 %, respectively. The mass ratios of the dark energy (68.47(23) %) and matters (31.53(23) %) obtained from the Planck 2018 results are consistent with the calculated mass ratios of the DER (67.5 %) and matters (32.5 %). The mass ratio of the dark energy (72.1(15) %) obtained from the WMAP 9 year results is explained as the summed mass ratio (72.5 %) of DER (67.5 %) and neutrinos (5.0 %). The universe evolution including the super-massive black holes (SMBHs) is shown in Fig. 4. The accelerated space expansion of our universe requires the addition of the new dark energy. If this new dark energy is added, the mass ratio of the dark energy is a little bit increased. The difference (0.97 %) between the observed value (68.47(23) %) and calculated value (67.5 %) is explained by adding the new dark energy in Figs. 2, 4, 7, 8, 9, 10 and 11. The corrected mass ratios of DER, DMs, leptons and quarks are 68.47 %, 21.8286 %, 7.2762 % and 2.4254 %, respectively. The corrected mass ratios of the neutrinos (called as cosmic background neutrinos) and ordinary matters (OMs) are 4.8508 % and 4.8508 %, respectively. These corrected mass ratios can explain the mass ratios obtained from the WMAP and Planck missions. In other words, the mass ratios calculated from the best particle number combination support the elementary particles, dark matters and dark energy (photon space) proposed by the three-dimensional quantized space model based on the 10-D Euclidean space.

Background: The epidemiological situation generated by COVID-19 has cast into sharp relief the delicate balance between public health priorities and the economy, with businesses obliged to toe a line between employee health and continued production. In an effort to detect as many cases as possible, isolate contacts, cut transmission chains and limit the spread of the virus in the workplace, mass testing strategies have been implemented in both public health and industrial contexts to minimize the risk of disruption in activity. Objective: To evaluate the economic impact of mass workplace testing strategy as carried out by a large automotive company in Catalonia in terms of health and healthcare resource savings. Methodology: Analysis of health costs and impacts based on the estimation of mortality and morbidity avoided because of screening and the resulting savings in healthcare costs. Results: The economic impact of the mass workplace testing strategies (using both PCR and RAT tests) was approximately €10.44 per test performed or €5,575.49 per positive detected. 38% of this figure corresponds to savings derived from better use of health resources (hospital beds, ICU beds and follow-up of infected cases), while the remaining 62% corresponds to improved health rates due to avoided morbidity and mortality. In scenarios with higher positivity rates and a greater impact of the infection on health and the use of health resources, these results could be up to ten times higher (€130.24 per test performed or €69,565.59 per positive detected). Conclusion: In the context of COVID-19, preventive actions carried out by the private sector to safeguard industrial production also have concomitant public benefits in the form of savings in healthcare costs. Thus, governmental bodies need to recognize the value of implementing such strategies in private settings and facilitate them through, for example, subsidies.

The four solvent extractives obtained from aerial parts of Leucophyllum frutescens were evaluated for their Total Antioxidant Activity (TAA) by ammonium molybdate method, scavenging potential by 2,2-diphenyl-1-picrylhydrazyl (DPPH) and Trolox-Equivalent Antioxidant Capacity (TEAC) assays, metal-reducing potential by Cupric Reducing Antioxidant Capacity (CUPRAC) and Ferric Reducing Antioxidant Power (FRAP) assays, Total Phenolic Content (TPC), Total Flavonoid Content (TFC) and their biological activities. The study concluded that BULE exhibited total antioxidant activity (226.235±1.222 mg AA.Eq.gm-1 DE±S.D) by molybdate method, CHLE exhibited more scavenging potential (DPPH 209.589±8.500 mg trolox Eq.gm-1 DE±S.D and TEAC 210.166±7.954 mg trolox Eq.gm-1 DE±S.D) and reducing potential (CUPRAC 646.889±16.889 mg trolox Eq.gm-1 DE±S.D & FRAP 472.981±15.625 mg trolox Eq.gm-1 DE±S.D). Phytochemical quantification concluded high TPC by BULE (189.369±1.393 mg GA.Eq.gm-1 DE±S.D) and high TFC by CHLE (232.458±1.589 mg Qu.Eq.gm-1 DE±S.D). Strong inhibition of α-glucosidase and urease enzymes was observed by HELE (IC50 0.3321±0.007 mg.ml-1±SD) and BULE (IC50 4.09±0.357 mg.ml-1±SD) extractives, respectively. The hemolytic effect shown by hexane extract (HELE) was higher with HA50 25.545±0.927 ug.ml-1±SD whereas methanol (MELE), chloroform (CHLE), and butanol (BULE) exhibited hemolytic effects at higher concentration with HA50 400.067±1.364, 321.394±1.332, and 332.957±0.465 µg.ml-1±SD, respectively. GC-MS profiling of HELE of L. frutescens was performed for qualitative analysis. The principal phytochemicals tentatively identified by GC-MS analysis of HELE accounts for fatty acids (60.221%), lignans (17.687%), ketones (3.358%), phenols (2.584%), sesquiterpenes (1.265%), and aldehydes (0.345%).

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

Air quality and environmental fairness have always been an area of prime interest across the globe. The significance low-cost air quality sensing and practices spikes during the time of pan-demic and epidemics when the air becomes a threat to living beings especially human beings. The gradual innovation and enrichment in low-cost air quality sensing sensors, nodes or devices, and systems are exponentially increasing for the last three decades. This work reviews the major contributions in a) low-cost scalable air quality assessment; b) low-cost air quality sensors, sensing approaches and technologies; c) low-cost state-of-the-art gas sensors fabrication methods (MEMS and CMOS); d) low-cost gas sensors measurement configurations and assemblies; and e) low-cost air quality sensors calibration and testing systems. A systematic review of past work with a goal to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies has been rendered in this work. Starting from sensors electrodes to IoT based mobile smart nodes; all have been introduced in this article.

Background and Objectives: The relevance of red flags in serious spinal pathology (SSP) evolved throughout the last years. Recently, new considerations have been proposed to expand the consideration of red flags. The purpose of this study was to determine, approve and test a model for the triage and manage-ment process of SSP based on the latest data available in the literature. Materials and Methods: The SSP model was initially built on the basis of a literature re-view. The model was further determined and approved by an expert panel us-ing a Delphi process. Finally, clinical scenario were used to test the applicabil-ity of the model. Results: After three rounds of Delphi process, panellists reached a consensus on a final version of the model. The use of clinical scenari-os by experts bring about reflexive elements both on the determined model and on the evocative SSP of the clinical cases. Conclusions: The validation of the model and its implementation in the clinical field could help assess the skills of first-line practitioners managing spinal painful patients. To this end, the devel-opment of additional clinical scenarios fitting with the determined model should be further considered.

Patients with metastatic triple negative breast cancer (TNBC) need new therapies to improve the low survival rates achieved with standard treatments. In this work, we show that the survival of mice with metastatic TNBC can be markedly increased by replacing their normal diet with artificial diets in which the levels of amino acids (AAs) and lipids are strongly manipulated. After observing selective anticancer activity in vitro, we prepared five artificial diets and evaluated their anticancer activity in a challenging model of metastatic TNBC. The model was established by injecting 4T1 murine TNBC cells into the tail vein of immunocompetent BALB/cAnNRj mice. First-line drugs doxorubicin and capecitabine were used as positive controls. AA manipulation led to modest improvements in mice survival when the levels or lipids were normal. Reducing lipid levels to 1% markedly improved the activity of several diets with different AA content. Mice fed the artificial diets as monotherapy lived longer than mice treated with doxorubicin and capecitabine. An artificial diet without 10 non-essential AAs, with reduced levels of essential AAs, and with 1% lipids improved the survival not only of mice with TNBC but also of mice with other types of metastatic cancers.

To understand the physiological basis of tolerance to combined stresses to low phosphorus (P) and drought in mungbean (Vigna radiata (L.) R. Wilczek), a core set of 100 accessions were evaluated in hydroponics at sufficient (250 μM) and low (3 μM) P, and exposed to drought (dehydration) stress. The principal component analysis and ranking of accessions based on relative values revealed that IC280489, EC397142, IC76415, IC333090, IC507340 and IC121316 performed superior while IC119005, IC73401, IC488526 and IC325853 performed poorly in all treatments. Selected accessions were evaluated in soil under control (sufficient P, irrigated), low P (without P, irrigated), drought (sufficient P, withholding irrigation) and combined stress (low P, withholding irrigation). Under combined stress, a significant reduction in gas exchange traits (photosynthesis, stomatal conductance, transpiration, instantaneous water use efficiency), P uptake in seed and shoot was observed under combined stress as compared to individual stresses. Among accessions, IC488526 was most sensitive while IC333090 and IC507340 exhibited tolerance to individual or combined stress. The water balance and low P adaptation traits like membrane stability index, relative water content, specific leaf weight, organic acid exudation, biomass, grain yield and P uptake can be used as physiological markers to evaluate for agronomic performance. Accessions with considerable resilience to low P and drought stress can be either used as ‘donors’ in Vigna breeding program or cultivated in areas with limited P and water availability or both.

Vitamin C is an essential nutrient that must be obtained through the diet in adequate amounts to prevent hypovitaminosis C and the potentially fatal deficiency disease scurvy. Global vitamin C status and prevalence of deficiency has not previously been reported, despite vitamin C’s pleiotropic roles in both non-communicable and communicable disease. This review highlights the global literature on vitamin C status and the prevalence of hypovitaminosis C and deficiency. Related dietary intake is reported if assessed in the studies. We also explore if global vitamin C status has changed over time. Overall, the review illustrates the shortage of high quality epidemiological studies of vitamin C status in many countries, particularly low- and middle-income countries. The available evidence indicates that vitamin C deficiency is common in low- and middle-income countries and not uncommon in high income settings. Further high quality studies are required to confirm these findings, including in the countries not yet represented, and to fully understand associations with a range of disease processes. Our findings suggest a need for interventions to prevent deficiency in a range of at risk groups and regions of the world.

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI–TOF MS) is a commonly used technique for analyzing large biomolecules. However, the utilization of organic matrices limits the small-molecule analysis because of the interferences in the low-mass region and reproducibility issues. To overcome these limitations, a surface-assisted laser desorption/ionization (SALDI), which utilizes nanostructured metallic surfaces, has been developed. Herein, a novel approach for SALDI–MS was proposed using nanoengineered gold shell with nanogaps on the silica core (SiO2@Au NGS), which is an emerging material due to its excellent heat-generating capabilities. The gold shell thickness was controlled by adjusting the concentration of gold precursor for the growth of gold nanoparticles. SALDI-MS measurements were performed on a layer formed by drop-casting a mixture of SiO2@Au NGS and analytes. At the optimized process, the gold shell thickness was observed to be 17.2 nm, which showed the highest absorbance. The ion desorption efficiency was confirmed with a survival yield upon fragmentation. Based on the enhanced SALDI capability, SiO2@Au NGS was utilized to detect various small molecules including amino acids, sugars, and flavonoids. The limits of detection, reproducibility, and salt tolerance of SiO2@Au NGS demonstrate its potential as an effective and reliable SALDI material for small-molecule analyses.

Following the 2001 end to negotiations on a legally binding protocol, Biological and Toxin Weapons Convention (BWC) states parties (SPs) developed entrenched positions about the necessity of a verification regime, hindering progress on treaty aims. This study aimed to facilitate dialogue on verification-related issues outside the context of those positions, using the term "assurance" to represent the degree of certainty that SPs are meeting their treaty obligations. From August 2020-July 2021, 36 interviews were conducted—16 SPs' delegations and 20 subject matter experts, representing 20 countries—and interview content was analyzed utilizing a mixed methods approach, including quantitative metrics on qualitative interview content. Interviewees' views on verification, compliance, and related concepts varied widely. Efforts by SPs to achieve common understanding on these topics could facilitate concrete progress in these important areas. While no single mechanism is sufficient to achieve verification or assess compliance, packages of mechanisms could increase assurance. There was general support for implementing assurance mechanisms, even in the absence of a comprehensive, legally binding protocol or verification regime, even among SPs for which that is the primary goal. Avenues to increase assurance among BWC stakeholders merit further discussion in the Intersessional Programme following the 9^th BWC Review Conference.

Protein import into the endoplasmic reticulum (ER) is the first step in the biogenesis of about 10,000 different soluble and membrane proteins in humans. It involves co- or post-translational targeting of precursor polypeptides to the ER and their subsequent membrane insertion or translocation. So far, three pathways for ER targeting of precursor polypeptides plus four pathways for ER targeting of mRNAs were described. Typically, these pathways deliver their substrates to the Sec61 polypeptide-conducting channel in the ER membrane. Next, the precursor polypeptides are inserted into the ER membrane or translocated into the ER lumen, which may involve auxiliary translocation components, such as the TRAP and Sec62/Sec63 complexes, or auxiliary membrane protein insertases, such as EMC and the TMCO1 complex. Recently, the PEX19/PEX3-dependent pathway, which has a well-known function in targeting and inserting various peroxisomal membrane proteins into pre-existent peroxisomal membranes, was also found to act in targeting and, putatively, inserting monotopic hairpin proteins into the ER. These either remain in the ER as resident ER membrane proteins or are pinched off from the ER as components of new lipid droplets. Therefore, the question arose if this pathway may play a more general role in ER protein targeting, i.e. represents a fourth pathway for ER targeting of precursor polypeptides. Thus, we addressed the client spectrum of the PEX19/PEX3-dependent pathway in both PEX3-depleted HeLa cells and PEX3-deficient Zellweger patient fibroblasts by an established approach, which involves label-free quantitative mass spectrometry of the total proteome of depleted or deficient cells and differential protein abundance analysis. The negatively affected proteins included twelve peroxisomal proteins and two hairpin proteins of the ER, thus confirming two previously identified classes of putative PEX19/PEX3-clients in human cells. Interestingly, fourteen collagen-related proteins with signal peptides or N-terminal transmembrane helices and belonging to the secretory pathway were also negatively affected by PEX3-deficiency, which may suggest compromised collagen biogenesis as a hitherto unknown contributor to organ failures in the respective Zellweger patients.

The principle of the constancy of the velocity of light, which stated that the light velocity is invariant to the motion of the emitter, was well established and directly proven by experiments. Interestingly, the further assumption that the light velocity is independent of the motion of the observer was, arguably, never directly proven by any experiment for a century. This paper proposed the design of two experiments to directly test this assumption, which tried to address some perceived technical difficulty in such experiments. One is to directly measure the light speed as to moving sensors. The experiment setup is designed in such a way that the concerns of time synchronization and dilation can be avoided. Another experiment is to test the isotropy of the light speed to a moving particle in the electromagnetic accelerator by measuring the momentum to acceleration ratio. The experiment result, if positive, will provide direct and solid proof of the assumption. Otherwise, it may imply a need for further investigation. Since the light speed invariance to moving observers is a key assumption of some fundamental physical theory, either way, the experiments will have significant meanings.

Glycosyl inositol phospho ceramides (GIPCs) are the major sphingolipids on earth as they account for a considerable fraction of the total lipids in plants and fungi which in turn represent a large portion of the biomass on earth. Despite their obvious importance, GIPC analysis remains challenging due to the lack of commercial standards and automated annotation software. In this work, we introduce a novel GIPC glycolipidomics workflow based on reversed-phase ultra-high pressure liquid chromatography coupled to high-resolution mass spectrometry. For the first time, automated GIPC assignment was performed using the open-source software Lipid Data Analyzer based on platform-independent decision rules. Four different plant samples (salad, spinach, raspberry, strawberry) were analyzed and revealed 64 GIPCs based on accurate mass, characteristic MS2 fragments and matching retention times. Relative quantification using lactosyl ceramide for internal standardization revealed GIPC t18:1/h24:0 as the most abundant species in all plants. Depending on the plant sample, GIPCs contained mainly amine, N-acetylamine or hydroxyl residues. Most GIPCs revealed a Hex-HexA-IPC core and contained a ceramide part with a trihydroxylated t18:0 or t18:1 long chain base and hydroxylated fatty acid chains ranging from 16 to 26 carbon atoms in length (h16:0 – h26:0). Interestingly, six GIPCs containing t18:2 were observed in raspberry, which was not reported so far. The presented workflow supports the characterization of different plant samples by automatic GIPC assignment potentially leading to the identification of new GIPCs. For the first time, automated high‑throughput profiling of these complex glycolipids is possible by liquid chromatography-high-resolution mass spectrometry and subsequent automated glycolipid annotation based on decision rules.

A novel effective vibrational mode was discovered in the conventional transducer with an array of orthogonal (square) regular piezoelectric rods in 1-3 piezocomposite, containing the damping backing and front matching layers. The operational resonance in the structure was determined as the Surface Acoustic Wave (SAW) on the backing boundary excited by the adjacent piezo-rods, with its frequency typically near 3 times lower the fundamental half-lambda conventional piezocomposite resonance. Pulse-echo sensitivity and transmitting sound-pressure-level (SPL) in air showed that the signal strength is roughly comparable to the industrial similar air transducers at the frequency range 100…700 kHz, where at these frequencies the lateral and longitudinal piezoelement dimensions in the conventional transducer design are typically close to each other causing interference with unwanted coupling modes. As was determined theoretically and proved in experiments, the backing SAW resonance effect in the transducer performance is inherent just to the regular periodic 1-3 piezocomposite structure, and does occur neither with randomly located/oriented piezo-rods, nor in the homogeneous piezo-plate at least with the same lateral cross-section as the connected to it backing. The purpose of the article is to investigate a newly discovered operational vibrational mode of a SAW type in 1-3 regular piezocomposite, other than piezoelectric resonance. The investigated phenomena can improve the transceiver sensitivity, bandwidth, providing lower drive voltage, and smaller and lighter weight ultrasonic transducers. Based on the piezocomposites with thickness’ 1…1.5 mm (rod resonance near 2…3 MHz), pillar width 0.2…0.8 mm, kerf width 0.1…0.4 mm, the transceivers with an operating frequency from 140 kHz to 650 kHz were designed and fabricated with a conventional backing of a mixture of high-density tungsten powder and epoxy, and a matching layer of a mixture of low-density glass bubbles and epoxy. Experimental evaluation of their acoustical performance showed expected characteristics suitable for practical applications.

We herein described an investigation of a theory, which describes the energies of neutrinos and the source of neutrino oscillations. A series of experiments were conducted to show evidences of the existence a neutrino mass. We also applied theories to explain the reason for the extremely small energy of a neutrino, mainly by employing a vacuum-derived superconducting energy gap from the Bardeen–Cooper–Schrieffer ground state. Moreover, we succeeded in obtaining the transition probabilities of neutrinos’ flavors (i.e., in terms of neutrino oscillation). We focused on the fact that up- and down-quantized space pairs combine by the Lorentz forces, undertake Bose-Einstein condensation, and then create a superconducting energy gap at the energy level of the vacuum with quantum mechanics fluctuation. Eventually, the superconducting energy gap vanishes to form a real body of the neutrino. Furthermore, assuming that the speed of the neutrino is near the speed of light and exhibits Planck’s blackbody emissions, we derived many-body interactions of neutrinos and applied them in Fermi’s golden rule. As a result, the neutrino energy we calculated agreed well within the realms of the experimental results. The calculated transition probabilities of neutrino’s flavor also explain the experiment results very well.

The last decade has seen a significant growth in low-cost air quality monitoring systems (LCAQMS) adoption, mostly driven by the spatial density limitations of traditional regulatory grade networks which restrict their effectiveness in several settings. The EU's regulatory framework advise for deploying one air quality monitoring unit per roughly 170,000 people or 15 square kilometers which is insufficient for capturing high spatio-temporal variance in complex urban scenarios. Often these settings are characterized by distributed emissions in small roads subjected to intense cars traffic, house heating driven emissions and frequently subjected to canyon effects. The Air Heritage project in Portici, funded by the EU's Urban Innovative Actions (UIA) program, addressed these challenges by integrating low-cost sensors with traditional monitoring systems and engaging the community in pervasive measurement strategies. The project highlights the importance of individualized sensor calibration and frequent recalibrations to maintain accuracy. It also showcases the benefits of citizen science approaches, IoT infrastructures, AI components, and geostatistical sensor fusion algorithms for mobile and opportunistic air quality measurements. This paper reports on the lessons learned and experiences from the Air Heritage project, aiming to guide future implementations in similar contexts. By sharing these insights along with the gathered datalake, we aim to inform stakeholders, including researchers, public authorities, and citizens, about effective strategies for deploying and utilizing LCAQMS to enhance air quality monitoring and public awareness.

This paper addresses the challenges of improving the accuracy of low-cost particulate matter sensors (LCPMS) under high humidity conditions. Such weather conditions often lead to the overestimation of particle counts due to hygroscopic particle growth, resulting in a potential public concern, although most of the detected particles consist of just water. The paper presents an innovative design for an indicative air-quality measuring station that integrates the particulate matter sensor with a preconditioning subsystem designed to mitigate the impact of humidity. The preconditioning subsystem works by heating the incoming air, effectively reducing the relative humidity and preventing the hygroscopic growth of particles before they reach the sensor. To validate the effectiveness of this approach, parallel measurements were conducted using both preconditioned and non-preconditioned sensors over a period of 19 weeks. The data was analyzed to compare the performance of the sensors in terms of accuracy for PM1, PM2.5, and PM10 particles. The results demonstrated a significant improvement in measurement accuracy for the preconditioned sensor, especially in environments with high relative humidity. When the conditions were too severe and both sensors started measuring incorrect values, the preconditioned sensor measured values were closer to the actual values. Also, the period of measuring incorrect values was shorter with the preconditioned sensor. The results suggest that the implementation of air preconditioning subsystems in LCPMS can provide a cost-effective solution to overcome humidity-related inaccuracies, thereby improving the overall quality of measured air pollution data.

This paper investigates the effect of innovative cross-sectional configurations on Low-Cost Bamboo Composite (LCBC) structural members. The study employs both experimental and numerical methods with different resin matrices and bamboo species. In this study, LCBC short columns are designed with different innovative cross-sectional configurations in an attempt to overcome the costly production processes of engineered bamboo. This approach uses bundles of bamboo, both in culm and strip forms. A compatible, environmentally responsible, and economically justifiable resin matrix is used to fabricate an LCBC member. The production of LCBC members does not necessitate highly advanced technology. This capability enables the production of LCBC members in custom-designed cross-sectional shapes and lengths. This study introduces the Russian doll (RD), Big Russian doll (BRD), Hawser (HAW), and Scrimber (SCR) cross-sectional configurations. Extra-large, large, medium, and small sizes of bamboo are employed. Synthetic Epoxy (EXP), a Bio-based Experimental soft filler (BE1), Bio-Epoxy (BE2), Furan-based (PF1) matrices are applied. Furthermore, Moso, Guadua, Madake, and Tali bamboo species are incorporated. The results of this study reveal that the most efficient cross-sectional configuration for compressive strength is the HAW configuration, closely followed by SCR configuration. LCBC members with bio-resins have shown excellent promise in competing in strength with those made with their synthetic counterparts. The theoretical and numerical modeling of the LCBC members showed excellent correlation with the experimental results which provides the capacity to design LCBC for engineering projects. The LCBC design can be further developed with more bamboo and less resin content.

Organosilicate glass (OSG) films are a vital component in modern electronic devices, with their electrical properties playing a crucial role in device performance. This comprehensive review systematically examines the influence of chemical composition, vacuum ultraviolet (VUV) irradiation, and plasma treatment on the electrical properties of OSG films. Through an extensive survey of literature and experimental findings, we elucidate the intricate interplay between these factors and the resultant alterations in electrical conductivity, dielectric constant, and breakdown strength of OSG films. Key focus areas include the impact of diverse organic moieties incorporated into the silica matrix, the effects of VUV irradiation on film properties, and the modifications induced by various plasma treatment techniques. Furthermore, we discuss the underlying mechanisms governing these phenomena, shedding light on the intricate molecular interactions and structural rearrangements occurring within OSG films under different environmental conditions. This review not only consolidates existing knowledge but also identifies gaps in understanding and suggests avenues for future research, thereby advancing our comprehension of OSG film behavior and paving the way for enhanced performance in next-generation electronic and photonic devices.

Low-cost personal exposure monitors (PEMs) to measure personal exposure to air pollution are potentially promising tools for health research. However, their adoption requires robust validation. This study evaluated the performance of twenty-one Plume Lab Flow2 (PLF) by comparing its air pollutant measurements, particulate matter with a diameter of 2.5 μm or less (PM2.5), 10 μm or less (PM10), and nitrogen dioxide (NO2), against several high-quality air pollution monitors under field conditions (at indoor, outdoor, and roadside locations). Correlation and regression analysis were used to evaluate measurements obtained by different PLFs against reference instrumentation. For all measured pollutants, the overall correlation coefficient between the PLFs and the reference instruments was often weak (r<0.4). Moderate correlation was observed for one PLF unit at indoor location and two units at roadside location, when measuring PM2.5, but not for PM10 and NO2 concentration. During periods of particularly higher pollution, 11 PLF tools showed stronger regression results (R2 values > 0.5) with one-hour and 9 PLF units with one-minute time interval. Results show that the PLF cannot be used robustly to determine high and low exposure to poor air. Therefore, the use of PLFs in research studies should be approached with caution if data quality is important to the research outputs.

Highly pathogenic (HP) avian influenza viruses (AIVs) are naturally restricted to H5 and H7 subtypes with a polybasic cleavage site (CS) in the hemagglutinin (HA) and any AIV with an intravenous pathogenicity index (IVPI) ≥1.2. Only few non-H5/H7 viruses fulfill the criteria of HPAIVs; nevertheless, it remains unknown why these viruses did not spread in domestic birds. In 2012, a unique H4N2 virus with a polybasic CS 322PEKRRTR/G329 was isolated from quails in California which, however, was avirulent in chickens. This is the only known non-H5/H7 virus with four basic amino acids in the HACS. Here, we investigated the virulence of this virus in chickens after expansion of the polybasic CS by substitution of T327R (322PEKRRRR/G329) or T327K (322PEKRRKR/G329) with or without reassortment with HPAIVs H5N1 and H7N7. The impact of single mutations or reassortment on virus fitness in vitro and in vivo was studied. Efficient cell culture replication of T327R/K carrying H4N2 viruses increased by trypsin, particularly in MDCK cells, and reassortment with HPAIV H5N1. Likewise, replication, virus excretion and bird-to-bird transmission of H4N2 was remarkably compromised by the CS mutations, but restored after reassortment with HPAIV H5N1, although not with HPAIV H7N7. Viruses carrying the H4-HA with or without R327 or K327 mutations and the other gene segments from HPAIV H5N1 exhibited high virulence and efficient transmission in chickens. Together, increasing the number of basic amino acids in the H4N2 HACS was detrimental for viral fitness particularly in vivo but compensated by reassortment with HPAIV H5N1. This may explain the absence of non-H5/H7 HPAIVs in poultry.

Introduction: The COVID-19 pandemic highlighted the necessity for rapid, efficient testing at large-scale events. Developing rapid and efficient testing methods was critical, especially for events with a high risk of virus spread. The queueing theory offers a powerful tool to manage the flow of people through testing centers. This study uses the M/M/c model to examine how different floor plan configurations impact the efficiency of RADT testing centers. Aim of the study: This research applies queueing theory to optimize the Rapid Antigen Diagnostic Test (RADT) processes at mass gatherings. The study uses the M/M/c queueing model to evaluate the dynamics of RADT centers configured in U-shaped and straight-line layouts. The primary goal is to assess the feasibility of using RADTs efficiently at events and mass gathering entrances, aiming to enhance throughput and minimize wait times. Methodology: The study involved 500 healthy participants, managed by medical staff across a U-shaped and a straight floor plans. Agile management techniques were employed to enhance operational efficiency. The process stages included queue number issuance, registration, sample collection, sample mixing, and results dissemination. Results: Both floor plans enabled the completion of RADT screening in approximately 2 minutes per participant. The U-shaped layout slightly outperformed the straight-line setup in efficiency, demonstrating its effectiveness in optimizing the testing process. Conclusion: This study confirms the feasibility of implementing Rapid Antigen Diagnostic Test (RADT) processes at mass gatherings. It was found that the U-shaped floor plan configuration is particularly effective, indicating its potential suitability for future mass testing scenarios.

Obesity in adolescents combined with the increased exposure time to electronic devices, enhances a sedentary lifestyle and is linked to the risk of developing musculoskeletal injuries. The aim of this study was to identify possible correlations between anthropometric characteristics, body composition, exposure time to electronic devices or screen time (ST) and physical activity (PA) level along with muscle power and dynamic knee valgus (DKV) in young athletes to avoid future injuries. A total of 125 adolescent basketball athletes (66.4% boys), 12 to 17 years old (13.94±1.58 years) participated. Anthropometric and demographic characteristics were recorded. PA level was assessed through IPAQ and ST through a single question from the HELENA study. The Counter Movement Jump test was used for the evaluation of the lower limb muscle power, while the Single Leg Drop Jump test was used for the evaluation of the dynamic knee valgus via two-dimensional (2D) kinematic analysis. The Pearson index showed a statistically significant positive correlation between muscle power and height (r=0.788, p<0.001), while the Spearman index showed a smaller but equally statistically significant positive correlation with BMI (rs =0.651, p<0.001) and age (rs=0.579, p<0.001). The ST (rs= -0.194, p=0.03) showed a weak negative correlation with DKV, while PA (r=0.85, p<0.001) showed a high, statistically significant, positive correlation. The anthropometric characteristics of adolescent athletes can determine their ability to produce muscle power. A high level of physical activity could play a key role in compensating and thus reducing the negative effects of high exposure to screen time on the dynamic knee valgus

Abstract：Objective: To compare the effects of fermentation on the chemical composition of Gastrodia Tuder Halimasch Powder, and to provide a basis for the processing, processing and clinical application of this medicinal material. Methods: UHPLC-Q-Orbitrap HRMS was used to identify compound structure by comparing excimer ions, characteristic fragment ions and reference substances, and referring to relevant literature and database search. The main differential components were screened by orthogonal partial least squares-discriminant analysis (OPLS-DA), and the differential components were quantitatively studied by high performance liquid chromatography, and the differences in the types and contents of chemical components before and after fermentation were compared. Results: A total of 77 compounds were identified or preliminarily derived after fermentation, including 21 terpenes, 18 organic acids, 9 flavonoids, 7 nucleosides, 6 amides, 4 amino acids, 2 pyrrolidone derivatives, 2 sterols, 2 alkaloids and 6 others.Through high performance liquid chromatography, it was found that the content of daidzein genistein and ergosterol was significantly increased after fermentation, and a new component ergosterol was produced. Compared with Gastrodia Tuder Halimasch Powder before fermentation, the content of genistin and other components was significantly reduced, and there may be a process of genistin conversion to genistein.Conclusion: The fermentation process will have a certain influence on the types and contents of the chemical components of Gastrodia Tuder Halimasch Powder, and ergosterol, genistein and .daidzein may be the main pharmacodynamic components, which can provide a useful reference for the clinical rational application, quality control and mechanism of action of Gastrodia Tuder Halimasch Powder.

Modern surface analysis techniques are expanding significantly possibilities in description and attribution of historical artifacts. The present study is aimed to compare analytical ability of the X-ray fluorescent analysis (XRF) typically applied for studies ceramic art items with novel surface analysis methods: time-of-flight secondary ions mass spectroscopy (SIMS) and X-ray photoelectron spectroscopy (XPS) that were applied on measurements of elemental compositions of powder raw materials for porcelain fabrication: pegmatite P-1, Vesco-prima clay, kaolin, bone earth, dolomite, and feldspar. It was shown that SIMS successfully measures light elements unnoticeable for XRF such as lithium, beryllium, boron and heavy impurities not found out by XRF such as cobalt, cerium, copper, rubidium, vanadium. XPS has found thorium in the kaolin sample that was not detected by SIMS and XRF. The paper provides also values of chemical shifts of some XPS lines observed in materials under examination. The obtained information on relations of basic and impurity elements revealed by XRF and SIMS together with XPS chemical shifts data could be used to expose contemporary falsifications of historical porcelain and to attribute porcelain items during conservation process.

By modifying the basic definition of cosmic red shift, considering ‘speed of light’ as an absolute cosmic expansion rate and adopting ‘Planck mass’ as the basic seed of the observed large scale universe, it is certainly possible to review and revise the basic picture of ‘standard cosmology’ and in near future, a perfect model of ‘white hole cosmology’ can be developed. In this context we have developed five assumptions. First three assumptions are based on ‘time reversed’ black holes and seem to be well connected with General theory of relativity as well as Quantum mechanics. 4^th and 5^th assumptions are helpful in understanding current galactic dark matter and flat rotation speeds. It may be noted that, considering our first three assumptions and considering the Planck Legacy 2018 data’s enhanced lensing amplitude in cosmic microwave background power spectra - conceptually, a closed universe having a positive curvature seems to be a best fit for the observed universe. With reference to our recent publication [26], for clarity on the subject, in this short communication, we make an attempt to review and explain our proposed assumptions at fundamental level. Our aim is to see that, professional and non-professional cosmologists must understand the basics of workable quantum cosmology.

Background: Acceleration of mass vaccination strategies is the only pathway to overcome the COVID-19 pandemic. Healthcare professionals and students have a key role in shaping public opinion about vaccines. This study aimed to evaluate the attitudes of dental students globally towards COVID-19 vaccines and explore the potential drivers for students' acceptance levels; Methods: A global cross-sectional study was carried out in February 2021 using an online ques-tionnaire. The study was liaised by the scientific committee of the International Association of Dental Students (IADS), and data was collected through the national and local coordinators of IADS member organizations. The dependent variable was the willingness to take the COVID-19 vaccine, and the independent variables included demographic characteristics, COVID-19-related experi-ence, and the drivers of COVID-19 vaccine-related attitude suggested by the WHO-SAGE; Results: A total of 6639 students from 22 countries representing all world regions responded to the ques-tionnaire properly. Their mean age was 22.06 ± 2.79 (17-40) years, and the majority were females (70.5%), in clinical years (66.8%), and from upper-middle-income economies (45.7%). In general, 22.5% of dental students worldwide were hesitant, and 13.9% rejected COVID-19 vaccines. The students in low- and lower-middle-income (LLMI) economies had significantly higher levels of vaccine hesitancy compared to their peers in upper-middle- and high-income (UMHI) economies (30.4% vs 19.8%; p < 0.001); Conclusions: The global acceptance level of dental students for COVID-19 vaccines was suboptimal, and their worrisome level of vaccine hesitancy was influenced by the socioeconomic context where the dental students live and study. The media and social media, public figures, insufficient knowledge about vaccines, and mistrust of governments and the pharmaceutical industry were barriers to vaccination. The findings of this study call for further implementation of epidemiology (infectious diseases) education within undergraduate dental curricula.

Design and advancement of the durable urban train infrastructures are of utmost importance for reliable mobility in the smart cities of the future. Given the importance of urban train lines, tunnels, and subway stations, these structures should be meticulously analyzed. In this research, two-dimensional modeling and analysis of the soil-structure mass of the Alan Dasht station of Mashhad Urban Train are studied. The two-dimensional modeling was conducted using Hashash’s method and displacement interaction. After calculating the free-field resonance and side distortion of the soil mass, this resonance was entered into PLAXIS finite element program, and finally, stress and displacement contours together with the bending moment, shear force and axial force curves of the structure were obtained.

Introduction. “Vein definition” for locally advanced pancreatic ductal adenocarcinoma (LA PDAC) assumes portal-to-superior mesenteric vein (PV/SMV) unreconstructability due to tumor involvement or occlusion. Radical pancreatectomies with SMV resection without PV/SMV reconstruction are scarcely discussed in the literature. Retrospective analysis of 19 radical pancreatectomies for “low” LA PDAC with SMV and all its tributaries resection without PV/SMV reconstruction has shown zero mortality, overall morbidity – 56%, Dindo-Clavien – 3-10,5%, R0- rate – 82%, mean operative procedure time – 355±154 min, mean blood loss – 330±170 ml, delayed gastric emptying– 25%, clinically relevant postoperative pancreatic fistula – 8%. In three cases surgery was associated with superior mesenteric (n2) and common hepatic artery (n1) resection. Surgery was completed without vein reconstruction (n13) and with inferior mesenteric-to-splenic anastomosis (n6). There were no cases of liver, gastric, or intestinal ischemia. A specific complication of the SMV resection without reconstruction was 2-3 days-long intestinal edema (48%). Median overall survival – 25 months, median progression-free survival – 18 months. All the relapses, except two, were distant. The possibility of successful SMV resection without PV/SMV reconstruction can be predicted before surgery by CT-based reconstructions. The mandatory anatomical conditions for the procedure were: 1) preserved SMV-SV confluence; 2) occluded SMV for any reason (tumor or thrombus); 3) well-developed inferior mesenteric vein collaterals with dilated intestinal veins; 4) no right-sided vein collaterals, and 5) no varices in the upper abdomen. Conclusion: “Low” LA PDACs involving SMV with all its tributaries can be radically and safely resected in highly and specifically selected cases without PV/SMV reconstruction with an acceptable survival rate.

This paper presents the design and measurement of an IEEE 802.11ad standard compatible RF transceiver for 60GHz wireless communication system. In addition to the traditional half-duplex (HD) mode, this work supports full-duplex (FD) operation to deliver better channel utilization and faster response time for the system. The isolation between the transmitter and receiver from the architecture design to system integration for FD operation has been fully considered. A digital self-interference cancellation (DSIC) is implemented in MATLAB to verify the FD performance. The super-heterodyne architecture with an intermediate frequency (IF) of 12GHz is designed to suppress the image frequencies without using extra filters. A flexible phase-locked loop (PLL) synthesizer provides a local oscillator (LO) frequency with a 2kHz resolution. Other than the time division duplex (TDD) mode used in the conventional 60GHz system, a wide bandwidth baseband digital variable gain amplifier (DVGA) with a 3dB bandwidth of more than 4GHz also supports frequency division duplex (FDD) operation. The transceiver chip is fabricated in Tower Jazz 0.18µm SiGe BiCMOS process. With on-board antenna, the transceiver covers all four channels in 802.11ad standard with MCS-12 (7.04Gbps under 1.76GSym/s and 16-QAM) under 1.5m. In the proposed system design, the RF frontend based self-interference (SI) suppression from the local transmitter to receiver LNA is around 54dB. To achieve a practical FD application, the SI is further suppressed with the help of digital SI compensation. The measured power consumption for transmitter and receiver configuration is 194mW and 231mW, respectively, in HD mode and 398mW for FDD or FD operation mode.

Fixed offshore wind turbines continue to be developed for high latitude areas where not only wind and wave loads need to be considered, but also moving sea ice. Current rules and regulations for the design of fixed offshore structures in ice-covered waters do not adequately consider effects of ice loading and its stochastic nature on fatigue life of the structure. Ice crushing on such structures results in ice-induced vibrations, which can be represented by loading the structure using a variable-amplitude loading (VAL) sequence. Typical offshore load spectra are developed for wave and wind loading. Thus, a combined VAL spectrum is developed for wind, wave, and ice action. To this goal, numerical models are used to simulate the dynamic ice-, wind-, and wave-structure interaction. The stress time-history at an exemplarily selected critical point in an offshore wind energy monopile support structure is extracted from the model and translated into a VAL sequence, which can then be used as a loading sequence for the fatigue assessment or fatigue testing of welded joints of offshore wind turbine support structures. This study presents the approach to determine combined load spectra and standardized time series for wind, wave, and ice action.

High dietary phosphate intake and poor adherence to phosphate-binding-therapy elevate the risk of hyperphosphatemia in maintenance hemodialysis (HD; MHD) patients. Therefore, chronic kidney disease-related mineral and bone disorder (CKD-MBD) indicators increase; consequently, risks of CKD-MBDs and inflammation are elevated. This double-blind, randomized control trial intervention study was designed to investigate the possibility of reducing blood CKD-MBD indicators and modulating inflammatory indicators by consuming low-phosphate (LP) meals accompanied by a minimum dose of a calcium-based phosphate binder (CaCO3). MHD patients were recruited and randomly assigned to an LP meal group (LP group) or a control group. After initial data collection, blood collection, and dietary counseling, subjects were asked to consume a washout diet for 1 week. During the washout diet period, subjects consumed their usual diet but took 1 tablet of calcium carbonate (1CaCO3) as a phosphate binder with each meal. After the washout diet period, subjects in the LP group and control group respectively consumed LP meals and regular meals twice a day for 1 week. Meat in the LP meals was boiled before the regular cooking process, but meat in control meals was not. All meals were supplied by a central kitchen so that the contents of phosphate and other nutrients could be identified. In total, 40 MHD patients completed the study program. After 1 week of the dietary intervention, the blood Ca x P product and dietary phosphate had significantly decreased in the LP group compared to the control group (p&lt;0.05). The LP group had significantly lower variations in dietary phosphate intake, blood calcium, Ca x P product, and tumor necrosis factor (TNF)-α than the control group by comparing differences between after the dietary intervention and the baseline (△after intervention - baseline, p&lt;0.05). The increase in dietary phosphate intake (△3rd - 2nd dietary phosphate intake) augmented the increase in the TNF-α level by 6.24-fold (odds ratio [95% confidence interval]: 6.24 [1.12~34.92], p&lt;0.05). These results highlighted the conclusion that LP meals accompanied by a minimum dose of CaCO3 downregulated pro-inflammation by reducing CKD-MBD indicators which was triggered by decreasing dietary phosphate intake.

According to the current European and Italian scenario related to urban re-generation, cultural and landscape heritage, valorisation is being also enhanced by the activation of innovative processes. These involve the development of methodologies and tools that are able to address decision-making processes among low entropy economy, complex values and creative practices. In this perspective, the research aims to investigate the possibilities of developing a Cultural Heritage Low Entropy Enhancement (CHLEE) approach by considering how the complex values of cultural heritage can vary not only through a physical transformation of spaces but also through a program of uses and activities able to produce new values, where the human experience is essential. This type of model modifies the objectives that characterise the valorisation of cultural heritage and landscape, recognising that the fruition is no longer “consumerist” but “experiential”. A crucial role is represented by the heterogeneity of creative practices that contribute to the identificationidentifying and implementation ofimplementing innovative management and governance models. The present paper explores the components of creative regenerative processes, based upon the ex-post evaluation of some Italian experiments, across the PROMETHEE-GAIA multi-criteria method, to understand how creative experiences are building innovation ecosystem thanks to low entropy economy and improve the ex-ante evaluation for new strategies and policies.

Improving the effectiveness of health interventions is a major challenge in public health research and program development. A large body of literature has found low or no impact of health education and promotional interventions. We aim to develop a conceptual framework in support of intervention designs for preventive health behavior improvement programs and outcomes. The proposed approach is based on a narrative review of empirical literature assessing the limitations of less effective or ineffective field experiments regarding preventive health education and promotion interventions. We found three major limitations regarding the mental model’s balance of treatment and comparison groups, treatment groups’ willingness to adopt suggested behaviors, and the type, length, frequency, intensity, and sequence of treatments. To minimize the influence of these concerns, we propose a mental model-based repeated multifaceted (MRM) intervention design framework to provide an intervention design for improving health education and promotional programs.

Under the main features required on portable devices in electrochemical instrumentation is to have a small size, low power consumption, economically affordable, and precision in the measurements. This paper describes the development of a programmable Embedded Potentiostat System (EPS) capable of performing electrochemical sensing over system-on-a-chip platforms. Furthermore, the study explains a circuit design and develops some validation of the entire system. The hardware validation is performed by electrochemical experiments such as Double Step Chronoamperometry (DSC), Linear Sweep Voltammetry (LSV) and Cyclic Voltammetry (CV); moreover, a comparison of the experimental signals between a commercial potentiostat and the EPS was done by analysis of errors on the response signal. Results illustrate that the EPS is capable of handling currents in the range of absolute values of 86.44 to 3000 nA, and having control voltages in the range of ± 2 V. The device can support from 50 to 2000 samples per second. The EPS capabilities were compared with other compact potentiostats. The programmable EPS is an original approach which hugely reduces the hardware complexity and leads the way to create new applications for Point-of-Care or industrial developments with a reusable full electronics module.

As the increase threat of flood risk and environmental safety due to the urbanization, Sponge city research has been attracting extensive attention both in practical and theoretical research field. To date, there are only scattered studies about Sponge city. Moreover, vary names of Sponge city prevalent in different countries, which leads to disconnection of literature in the same field of Sponge city. In this paper, a thorough systematic literature mining of Sponge city is presented. A literature analysis system is created, which includes literature export from Web of Sciences and systematic analysis via NoteExpress and CiteSpace. Some literature statistical results are derived. Challenges and opportunities for future research are anticipated. Our goals are to promote this promising thought, summarize past research, and identify issues for future research to create impacts on the practice of Sponge city.

A mass mortality event of Asian seabass Lates calcarifer juveniles occurred in Zhuhai, the main Asian seabass cultured area in mainland China. The fish samples were pooled for pathogen identification and both high viral loads of ISKNV and NNV were detected by real-time microfluidic quantitative PCR. Immunohistochemistry and immunofluorescence showed that strong ISKNV signals were examined in spleen and liver, while strong NNV signals were detected in brain and eye. The multi-tissue homogenates were inoculated into MFF-1 cell and SSN-1 cell, respectively. After several viral passages, both ISKNV and NNV were purely isolated from each other, and designated as ASB-ISKNV-23 and ASB-NNV-23, respectively. The whole genome sequences of ASB-ISKNV-23 and ASB-NNV-23 were determined and annotated. The result showed that ASB-ISKNV-23 and ASB-NNV-23 are composed of 112,236 bp and 4,538 bp, respectively. Phylogeny analysis showed that ASB-ISKNV-23 belongs to ISKNV-II sub-genotype and ASB-NNV-23 belongs to RGNNV genotype. Collectedly, coinfection of ISKNV-II and RGNNV were firstly documented in mass mortality of Asian seabass in mainland China. Importantly, both ISKNV-II and RGNNV were purely isolated using two different permissive cell lines. Our study provides useful information for better understanding the complex pathogenesis regarding the coinfection with ISKNV and NNV in farmed fish.

Abstract: Beetroot (Beta vulgaris L) has been known for being a rich source of phytochemicals, minerals and vitamins. This study presents a model system for how the combination of extrac-tion/chromatography/mass spectrometry and NMR offers an efficient way to profile metabolites in the extracts of a natural product, beetroot . Such combination may lead to the identification of more nutritional or medicinal compounds in natural products, and it is essential for our ongoing investigation to study the selective adsorption/desorption of these metabolites on nanoparticles. The aqueous and organic extracts underwent analyses using UV-vis spectroscopy; GC-MS; LC-MS; 1H, 13C, TOCSY, HSQC, and selective TOCSY NMR experiments. Polar Extract: The two forms of betalain pigment were identified by UV-vis and LC MS. Fourteen amino acids, sucrose, and other compounds among which is riboflavin, were identified by LC-MS. 2D TOCSY showed the spin coupling correlations corresponding to some of these compounds. The HSQC spectrum showed 1H/13C spin correlation in sucrose confirming the high abundance of sucrose in beetroot. Organic Extract: GC-MS data enabled the identification of several compounds including six fatty acid methyl esters (FAME) with higher than, on average, 90% similarity score. Selective TOCSY NMR data showed the spin coupling pattern corresponding to oleic, linoleic, and linolenic fatty acids. 31P NMR spectra indicate that phospholipids exist in both the organic and aqueous phases. Keywords: Beetroot (Beta vulgaris L); Total Correlation Spectroscopy (TOCSY); Gas Chromatog-raphy-Mass Spectrometry (GC-MS); selective TOCSY, Homonuclear single quantum correlation (HSQC); fatty acid methyl esters (FAME).