Bond Properties were performed on Ag-2.35Au-0.7Pd-0.2Pt-0.1Cu alloy wire with a diameter of 25 µm under different process parameters. Effects of electrical flaming off (EFO) current and EFO time on deformability of the free air ball (FAB) were investigated using scanning electron microscopy (SEM) as well as the effects of ultrasonic power and bonding force on the bond characteristic. The experimental results showed that, FAB grows from a preheated tip to a small ball, a regular ball and finally to a golf ball with increasing either the EFO current or the EFO time, and the FAB presented optimal shape at 25 mA and 650 μs. Moreover, a nonlinear relationship between FAB diameter and EFO time is obtained at the EFO current of 25 mA, which could be expressed by a cubic equation. Further, at a constant bonding force, as the ultrasonic power increased, the mashed ball diameter grew larger and larger, the capillary hole imprint became more and more obvious, and the tail width also increased larger and larger, and vice versa. The optimal ultrasonic power and bonding force are 70 mW and of 45 gf for ball bond and 90 mW and 75 gf for wedge bond, respectively. Finally, for all the bonded wire samples prepared under optimal process parameters, no ball and wedge bond lifts happened after destructive pull test, and full intermetallic compound coverage with perfect morphology occurred on the bond pad after ball shear test, which meant that the bonded wire samples have high bond strength, and hence improved the reliability of microelectronic products.

In this study, a new methodology based on the circuit approach is employed to obtain renewable electric energy. Although a voltage source and a current source generate voltage and current, respectively, they work only when they receive electric power, which is the product of voltage and current. However, this paper proposes a circuit with a voltage source, a current source and a super-condenser connected in series, in which the voltage source provides voltage for the current source and the current source provides current for the voltage source. Resultantly, electric power is generated both at the voltage and current sources, and the energy (i.e., the electric power) from the current source is converted to the charging energy in the super-condenser. Herein, we describe the method for charging the super-condenser using a voltage source and a current source. To confirm the abovementioned concept, we conducted experiments, and the energy was successfully produced, with high reproducibility. Finally, the brief mechanism for the energy conversion, a schematic method for reducing the capacitances of stored batteries, and the significance of this study are described.

In this work, we studies the principle of ground electrode current field through ground communication technology, signal design, and optimal working mode of excitation source, so as to adapt the working mode, working frequency, and transmission medium condition of signal transmission. Through waveform design, energy is concentrated in the main conduction direction, which is beneficial for signal filtering at the receiving end and achieving high reliability data transmission; On this basis, on-site environmental testing was conducted to verify the detection and recognition technology of weak signals. Signal design and detection recognition are a very important part of the grounding electrode current field through ground communication technology. The grounding electrode current field through ground communication technology is mainly applied to solve the problem of communication between rescue personnel and trapped personnel before and during tunnel engineering collapse and rescue.

With the proportional reduction of MOSFET size, the leakage-to-barrier reduction (DIBL) effect leads to a more significant increase in the tunneling current on the gate, and the appearance of the gate tunneling current also seriously affects the static characteristics of the device. In this paper, a new theoretical model of the relationship between the direct tunneling current and the thickness of the oxide layer under the DIBL effect is proposed for the MOSFET device with ultra-thin oxide layer. On this basis, the characteristics of the MOSFET device are studied in detail by using HSPICE, and their working conditions are quantitatively analyzed. The characteristic variation trend of small-size devices under the influence of gate tunneling current is predicted. The simulation results using BSIM4 model are consistent with the theoretical model. The theory and data in this paper will provide useful reference for large scale integrated circuit design.

Superconducting YBa2Cu3Oy (YBCO) foams were prepared using commercial open-cell, polyurethane foams as starting material to form ceramic Y2BaCuO5 (Y-211) foams which are then converted into superconducting YBCO by using the infiltration growth process. For modelling the superconducting and mechanical properties of the foam samples, a Kelvin-type cell may be employed as a first approach like done in the literature for pure polyurethane foams. However, for a refined model of a superconducting foam sample, the real sample structure must be considered. Thus, a proper description of the specific microstructure of the superconducting YBCO foams is required. A variety of parameters including the cell size and shape, the window size and shape, the length and shape of the foam struts or ligaments and the respective angles of intersection are used to describe the real foam structure. To obtain a set of reliable data, YBCO foam samples were investigated using optical microscopy, SEM and electron backscatter diffraction (EBSD). The detailed investigation of the foam microstructure reveals not only the differences to the polymeric foams used as base material, but also gives insight to details of the infiltration growth process via the increased surface amount in a foam sample.

Background. False memories tend to increase in healthy and pathological aging, and their reduction could be useful in improving cognitive functioning. The objective was to use an active-placebo method to verify whether the application of tDCS in improving true recognition and reducing false memories in healthy older people. Method. Participants were 29 healthy older adults (65-78 years old) assigned to active or placebo group; active group received anodal stimulation at 2mA for 20 min over F7. An experimental task was used to estimate true and false recognition. The procedure took place in two sessions on two consecutive days. Results. A mixed ANOVA of true recognition showed a significant main effect of session (p = .004), indicating an increase from before treatment to after it. False recognition showed a significant main effect (p = .004), indicating a decrease from before treatment to after it and a significant session x group interaction (p < .0001). Conclusions. Overall, our results show that tDCS is an effective tool for increasing true recognition and reducing false recognition in healthy older people, and suggest that stimulation improves recall by increasing the number of items a participant can recall and reducing the number of memory errors.

Coronavirus that is also known as COVID-19 disease is produced by SARSCoV-2. This causative agent is highly contagious and can cause potentially fatal pneumonia worldwide with serious public health concerns. In the beginning among infected individuals, most of them were those who were mainly shown to the wet animal market in a big city of China known as Wuhan. So, it was suggested that this was almost certainly the zoonotic source of COVID-19illness. The transitional source of origin and their mode of transmission to humans were not known obviously. Conversely, from human to human rapidly transformation have been confirmed generally. Currently, there is no availability of FDA approved clinically antiviral drugs and/or vaccines to be used against the COVID-19. Afterward, SARS-CoV and MERS-CoV, the occurrence of SARS-CoV-2 has been manifested as the third sketch of an enormously pathogenic coronavirus into human population globally. In this review, we provide a brief overview of the history of COVID-19 in Pakistan up-to 18^th weeks after beginning, current situation, epidemiology, and its impact on the human population. Moreover, we focused on physiological variation during the incubation period, genome analysis of SARS-CoV2, supportive treatment approaches, and safety measures in the Pakistani population, which may be supportive for combating the risk of COVID-19 epidemic. We also reviewed the future approaches for the development of therapeutic interventions and vaccines to cope with the COVID-19 epidemic.

In the recent years, intelligent data-driven faultdiagnosis methods on gearboxes have been successfully developedand popularly applied in the industries. Currently, most ofthe machine learning techniques require that the training andtesting data are from the same distribution. However, thisassumption is difficult to be met in the real industries, sincethe gearbox operating conditions usually change in practice,which results in significant data distribution gap and diagnosticperformance deteriorations in applying the learned knowledgeon the new conditions. This paper proposes a deep learning-based domain adaptation method to address this issue. Theraw current signals are directly used as the model inputs fordiagnostics, which are easy to collect in the real industries andfacilitate practical applications. The maximum mean discrepancymetric is introduced to the deep neural network, the optimizationof which guarantees the extraction of generalized machineryhealth condition features across different operating conditions.The experiments on a real-world gearbox condition monitoringdataset validate the effectiveness of the proposed method, whichoffers a promising tool for cross-domain diagnosis in the realindustries.

We report the effects of surface passivation by depositing a hydrogenated amorphous silicon (a-Si:H) layer on the electrical characteristics of low temperature polycrystalline silicon thin film transistors (LTPS TFTs). The a-Si:H layer was optimized by hydrogen dilution and its structural and electrical characteristics were investigated. The a-Si:H layer in the transition region between a-Si:H and µc-Si:H resulted in superior device characteristics. Using an a-Si:H passivation layer, the field-effect mobility of the LTPS TFT was increased by 78.4% compared with a conventional LTPS TFT. Moreover, the leakage current measured at a V_GS of 5 V was suppressed because the defect sites at the poly-Si grain boundaries were well passivated. Our passivation layer, which allows thorough control of the crystallinity and passivation-quality, should be considered a candidate for high performance LTPS TFTs.

Power converters with coupled inductors are very promising due to the high efficiency and high voltage gain. Apart from the aforementioned advantages, the boost-flyback converter reduces the voltage stress on the semiconductors. However, to obtain good performance with high voltage gains, the controller must include two control loops (current and voltage), and a compensation ramp. One of the most used control techniques for power converters is the peak current-mode control with compensation ramp. However, in the case of a boost-flyback converter there is no mathematical expression in the literature, to compute the slope of the compensation ramp. In this paper, a formula to compute the slope of the compensation ramp is proposed in such a way that a stable period-1 orbit is obtained. This formula is based on the values of the circuit parameters, such as inductances, capacitances, input voltage, switching frequency and includes some assumptions related to internal resistances, output voltages, and some other electrical properties related with the physical construction of the circuit. The formula is verified numerically using the saltation matrix and experimentally using a test circuit.

Electrical energy demand increase does evolve rapidly due to several socioeconomic factors such as industrialization, population growth, urbanization and of course the evolution of modern technologies in this 4th industrial revolution era. Such rapid increase in energy demand introduces a huge challenge in power system. Such has paved way for network operators to seek for alternative energy resources other than the conventional fossil fuel system. Hence, the penetration of renewable energy into the electricity supply mix has evolved rapidly in the past three decades. However, the grid system has to be well planned ahead to accommodate such increase in energy demand in the long run. Transmission Network Expansion Planning (TNEP) is a well ordered and profitable expansion of power facilities that meets the expected electric energy demand with an allowable degree of reliability. This paper proposes a TNEP model that minimises the network reinforcements, operational costs and costs of renewable energy penetrations, while satisfying the increase in demand. The problem is formulated as a mixed integer linear programming (MILP) problem. The developed model has been tested in several IEEE test systems in multi-period scenarios. The paper also carried out a detailed derivation of the new non-negative variables in terms of the power flow magnitudes, the bus voltage phase angles and the lines’ phase angles for proper mixed integer variables’ decomposition techniques. Moreover, this paper tends to provide additional recommendation in terms of which particular year (within 20 years of planning period) can the network operators install new line(s), new corridor(s) and/or additional generation capacity to the respective existing power networks. Such is achieved by running incremental periods simulations from base year through the planning horizon. The results show the efficacy of the developed model in solving the TNEP problem with a reduced and acceptable computation time even for large power grid system.

The zero offset voltage in anti-aliasing low-pass filters (LPF) included at the ADC input has a significant effect on the effective bit rate of the ADC. The article discusses methods for minimizing the systematic component of the zero offset voltage (V_OS) of operational amplifiers (Op-Amp) in the structure of the LPF, due to the degradation of the current gain of the base (b) of bipolar transistors for an extremely common subclass of Op-Amp with one high-impedance node. The methods of matching a high-impedance Op-Amp node and a buffer amplifier with the help of special correcting SCM^p and SCMⁿ multipolars are proposed. Methods of description and formation of the given coefficients of weak current asymmetry of typical Op-Amp functional units (current mirrors, input DS, buffer amplifiers, SRC, etc.) are presented. As an example, the results of computer simulation of GaAs Op-Amp with small V_OS performed on JFET field and p-n-p bipolar transistors are given.

KThe promising possibility of organic photodetector (OPD) is emerging in the field of sensing applications for its tunable absorption range, flexibility, and large-scale fabrication abilities. In this work, we fabricated bulk heterojunction OPD with a device structure of glass/ITO/PEDOT:PSS/ P3HT:PC61BM/Al by spin coating process and characterized the dark and photocurrent at different applied bias conditions for red, green, and blue incident LED light. OPD photocurrent density exhibited up to 2.5–3 orders higher magnitude compared to the dark current density at -1 V bias while it increased up to 3–4 orders at zero bias conditions for red, green, and blue lights showing an increasing trend higher voltage applied in the negative direction. Different OPD inner periphery shapes, OPD to LED distance, and OPD area were also considered to bring the variation in OPD dark and photocurrent, which can affect the on/off ratio of the OPD–LED hybrid system and is a critical phenomenon for any sensing application.

Global climate change has induced a rise in sea surface temperature (SST), although this increase is not uniform across the world. Significant variations exist between coastal and offshore waters, particularly in regions affected by upwelling processes. This study focuses on the Canary Current Upwelling System (CCUS), stretching from Northwest Iberia to Northwest Africa. High-resolution remotely sensed SST data (0.05°) from the ODYSSEA Level 4 Sea Surface Temperature Reprocessed dataset were validated with in-situ measurements and employed to establish a regional climatological baseline for 1982 – 2012. Subsequent years were compared to this baseline to construct SST anomaly maps, revealing SST changes since 2012. The study area was further divided into sub-regions for comparative analysis. Results indicate that SST consistently increased at a higher rate offshore compared to the adjacent nearshore regions. A reference dataset spanning 1951 – 1981 was used to gauge SST variability between the two baselines. SST exhibited a 0.59°C increase from 1951 – 1981 to 1982 – 2012, with a slowing of SST trends beyond the 1982 – 2012 baseline. This research offers valuable insights into the climatological dynamics of the CCUS. These findings enhance our understanding of this critical coastal system's climatology, laying the groundwork for future investigations into evolving climate patterns in coastal regions.

Resistive random-access memory has emerged as a promising non-volatile memory technology, garnering substantial attention due to its potential for high operational performance, low power consumption, and scalability. Two-dimensional nanostructured materials play a pivotal role in RRAM devices, offering enhanced electrical properties and physical attributes that contribute to overall device improvement. In this study, self-rectifying switching behavior in RRAM devices is proposed based on molybdenum disulfide nanocomposites decorated with palladium on SiO2/Si substrates. The integration of Pd and MoS2 at the nanoscale effectively mitigates leakage currents decreasing from cross-talk in the RRAM array, eliminating the need for a separate selector device. The successful demonstration of the expected RRAM switching behavior follows the application of a Pd nanoparticle coating. The fabricated Pd-MoS2 synaptic device showed a high current ratio for forward/reverse current higher than 60 at a low resistance state and observed a memory on/off ratio of 103 performing stable resistance switching behavior.

: In the automotive industry, high-strength plates have been increasingly used to reduce the vehicle body weight due to stringent regulations on fuel economy and safety. Such plates achieve tensile strengths as high as 1.5 GPa owing to the hot-stamping process. However, these plates suffer from scale generation and surface decarburization because of the surface oxidation of the material. Recently, studies on materials subjected to high-frequency induction heating have reported strength improvement owing to the coil shape and cooling method. This study presents the surface temperature changes, mechanical properties, and microstructures of boron steels subjected to longitudinal heating, which uses eddy currents generated from high-frequency induction heating. The surface temperature data were analyzed under different high-frequency induction heating powers (15, 18, 21, 24, 27, and 30 kW) and distances from the specimen (6, 9, and 15 mm). The mechanical properties and microstructures were also analyzed in different high-frequency induction heating coil directions. The correlations between the high-frequency induction heating power and the distance from the specimen with the maximum tensile strength were determined.

The battle of currents between AC and DC reignited as a result of the development in the field of power electronics. The efficiency of DC distribution systems is highly dependent on the efficiency of distribution converter, which calls for optimized schemes for efficiency enhancement of distribution converters. Modular solid-state transformers play a vital role in DC Distribution Networks and Renewable Energy systems (RES).This paper deals with efficiency-based load distribution for Solid State Transformers (SSTs) in DC distribution networks. Aim is to achieve a set of minimum inputs that are consistent with output while considering constraints and efficiency. As the main feature of modularity is associated with a three-stage structure of SSTs. This modular structure has been optimized using Ant Lion Optimizer (ALO) and validated by applying it EIA (Energy Information Agency) DC Distribution Network which contains SSTs. In the DC distribution grid, modular SSTs provide promising conversion of DC power from medium voltage to lower DC range (400V). The proposed algorithm is simulated in MATLAB and also compared with two other metaheuristic algorithms. The obtained results prove that the proposed method can significantly reduce input requirements for producing the same output while satisfying the specified constraints.

Article contents the analytical model of the drift of a separate ice field under action of wind and current, which velocities and directions can vary during time. Model takes into account the mass of ice, added mass of sea water and the effects of the wind and current on the ice field in form the friction on its upper and underwater surfaces and frontal resistance on its end (forward and backward) surfaces. Results of performed the steady wind drift of the ice fields modelling show the drift velocity exceeds considerable known velocity of a compact ice cover wind drift. Drifting ice field has the certain kinetic energy that should be released when collision with unmovable obstacle and spent on brittle breakdown of part of the ice field. Volume of formed small ice pieces (fragments of ice field) was estimated by comparison of the specific energy of the sea ice brittle destruction and the kinetic energy of drifting ice field. Article presents the results of estimation of possible volume of the ice pieces and the scales of formed piles as result of collision with an obstacle depending on initial dimensions of ice field and wind speed. Developed models and the results of computer modelling can be used to estimate the ice pile sizes near the stationary platforms and terminals on the Arctic seas.

The digital twin (DT) research field is experiencing rapid expansion, yet the research in industrial practices in this area remains poorly understood. This paper aims to address this knowledge gap by sharing feedback and future requirements from the manufacturing industry. The methodology employed in this study involves an examination of a survey that received 99 responses and interviews with 14 experts from 10 prominent UK organisations, most of which are in the defence industry in the UK. The survey and interviews explored topics such as DT design, return on investment, drivers, inhibitors, and future directions for DT development in manufacturing. The study findings indicate that DTs should possess characteristics such as adaptability, scalability, interoperability, and the ability to support assets throughout their entire life cycle. On average, completed DT projects reach the break-even point in less than two years. The primary motivators behind DT development were identified to be autonomy, customer satisfaction, safety, awareness, optimisation, and sustainability. Meanwhile, the main obstacles include a lack of expertise, funding, and interoperability. The study concludes that the federation of twins and a paradigm shift in industrial thinking are essential components for the future of DT development.

The aim of the study was to find the effect of polyethylene (PE) coatings on the short-circuit current of silicon photovoltaic cells covered with glass, in order to improve the short-circuit current of the cells. Various combinations of PE films (thicknesses ranging from 9 to 23 µm, number of layers ranging from 2 to 6) with glasses (greenhouse, float, optiwhite and acrylic glass) were investigated. The best current gain of 4.05% was achieved for the coating combining a 1.5 mm-thick acrylic glass with 2 × 12 µm-thick PE films. This effect can be related to the formation of an array of micro-wrinkles and micrometer-sized air bubbles with a diameter of 50 to 600 µm in the films, which serve as micro-lenses and enhance light trapping.

ADHD, a neurodevelopmental condition, is distinguished by a triad of symptoms including inattention, hyperactivity, and impulsivity. It is frequently accompanied by comorbidities such as anxiety, depression, and learning disabilities. As a result, clinicians often face challenges in accurately diagnosing ADHD and differentiating it from other conditions. As a prospective remedy for ADHD, scientists have investigated Transcranial Direct Current Stimulation (tDCS), a non-invasive technique of stimulating the brain. It involves applying low-intensity electrical currents to specific regions of the brain to modulate neural activity. This review paper aims to provide an overview of the comorbidities associated with ADHD and the differential diagnosis of the condition. It also explores the potential of tDCS as a treatment option for ADHD, including its mechanisms of action and efficacy in improving ADHD symptoms. The comorbidities discussed in this review include anxiety disorders, mood disorders, and substance use disorders. These comorbidities are frequently seen in individuals with ADHD and can complicate the diagnosis and treatment of the condition. The paper also highlights the importance of considering comorbidities when assessing ADHD, as well as the potential impact of these conditions on treatment outcomes. The differential diagnosis section of the paper explores conditions that can present with symptoms similar to ADHD, such as anxiety disorders, mood disorders, and learning disabilities. It emphasizes the need for a thorough assessment and differential diagnosis to identify ADHD and differentiate it from other conditions accurately. The final section of the paper discusses the potential of tDCS as a treatment option for ADHD. It examines the mechanisms of action of tDCS and its efficacy in improving ADHD symptoms, including attention, hyperactivity, and impulsivity. It also explores the potential for tDCS to improve comorbid conditions associated with ADHD. Overall, this review provides a comprehensive overview of comorbidities and differential diagnoses in ADHD and the potential of tDCS as a treatment option. The paper highlights the importance of a thorough assessment and personalized treatment plan for individuals with ADHD, particularly those with comorbidities.

Solar cosmic rays (SCR) are generated during the primordial energy release in solar flares. This explosive process takes place in the solar corona above the active region. It represents fast release of the magnetic field energy of the current sheet, which is formed near a singular magnetic field line. Solar cosmic rays appear as a result of acceleration of charged particles, mainly protons, by an inductive electric field in the current sheet, equal to the field E=V´B/c near the current sheet. To study the mechanism of solar flares and obtain conditions for stydy SCR acceleration it is necessary to carry out magnetohydrodynamic (MHD) simulation of a flare situation in the solar corona above a real active region. The methods of stabilization were developed which made it possible to solve partially the problem of numerical instabilities. MHD simulations showed complicated configuration near the singular line. Comparison of the results of MHD simulations with observations showed a general agreement of the positions of the current sheets with regions of intense flare radiation. However, there are some problems with the details of such coincidences. The results show the possibility of improving the methods of MHD simulation in order to solve the arisen problems.

An adaptive control technique has been implemented for DSTATCOM for power quality enhancement in three phase four wires(3P4W) distribution system. The reference source currents are extracted from active components of load current for each phase by using this technique. It has also been used for load balancing, harmonic suppression, power factor improvement and reactive power compensation in distribution system. The adaptive control technique has been tested at varying load in steady state and dynamic conditions. This technique is developed using MATLAB/Simulink and source side harmonics are mitigated under different load conditions which are acceptable in accordance with IEEE standard.

Aiming for the problems emerging in the PWM drive system with long cables, accurate modeling of power cables is the premise to predict and analyze the relevant phenomenon, and a proper filter design is the key solution to these problems. This paper proposes high-frequency cable models to represent the frequency-dependent characteristics, especially for the high-frequency resistance of the cable that is an easily overlooked factor but determines the damping of overvoltage. The proposed models can be used for accurately representing the cable parameters in a wide frequency range, and correctly simulating the differential mode (DM) overvoltage and common mode (CM) current, including the peak value, oscillation frequency and damping of the transient waveform. In addition, improved filter networks are proposed to suppress the DM voltage and CM current, with the merit of low losses, small volume and an excellent ability of suppressing overvoltage. The proposed cable models and the filter design have been validated in a 750W PWM drive system with 200m power cables.

In this paper we develop from first principles a unique law pertaining to the flow of fluids through closed conduits. This law, which we call “Quinn’s Law”, may be described as follows: When fluids are forced to flow through closed conduits under the driving force of a pressure gradient, there is a linear relationship between the normalized dimensionless pressure gradient, P_Q, and the normalized dimensionless fluid current, C_Q. The relationship is expressed mathematically as: P_Q = k₁ +k₂C_Q. This linear relationship remains the same whether the conduit is filled with or devoid of solid obstacles. The law differentiates, however, between a packed and an empty conduit by virtue of the tortuosity of the fluid path, which is seamlessly accommodated within the normalization framework of the law itself. When movement of the fluid is very close to being at rest, i.e., very slow, this relationship has the unique minimum constant value of k₁, and as the fluid acceleration increases, it varies with a slope of k₂ as a function of normalized fluid current. Quinn’s Law is validated herein by applying it to the data from published classical studies of measured permeability in both packed and empty conduits, as well as to the data generated by home grown experiments performed in the author’s own laboratory.

In the present work, a superlattice structure comprising superconducting and insulator layers is studied. Here, if a magnetic field is applied parallel to the layers, the lack of a pinning center leads to a novel transition; in particular, as the applied magnetic field is reduced, the stationary wave surrounding the magnetic flux quantum in the superconducting layer eventually collides with the superconducting–insulating interfaces on both sides because its radius becomes larger than the width of the superconducting layer. At this instant, the stationary wave will collapse, and a transition will occur: the magnetic quanta are collapsed and thus the uniform magnetic field distribution is achieved, which corresponds to the transition from the superconducting state to the normal state over critical current. Considering a one-dimensional model of the structure, a critical current density equation is derived that indicates an increase in the critical current density for increased applied magnetic field. Subsequently, the same calculation was conducted after changing the direction of the magnetic field component, and the combination of these two calculations expresses the anisotropic property of the structure. The phenomenon is also predicted for anisotropic critical current density. This phenomenon is an important discovery that helps manufacture high-temperature superconducting tape as well as large high-temperature superconducting coils.

Protective coatings, in recent years also from nanocomposite formulations, are commonly applied onto architectural stone and stone artefacts, mainly to prevent absorption into the porous stone structure of condensed water and dissolved atmospheric pollutants. While standard protocols are available to assess a coating’s performance, understanding the response of the coating-stone system is a complex task, due to the interplay of various factors determining the overall behaviour. Characterization techniques allowing to correlate the extent and nature of surface modification upon treatment with the most relevant physical properties (i.e water absorption and surface wettability) are thus of great interest. Electrokinetic analysis based on streaming current measurements, thanks to its sensitivity towards even minor changes in the surface chemical composition, may fulfil such requirement. Indeed, by involving the interaction with a testing aqueous electrolyte solution, this technique allows to probe not only the outer surface but also the outermost layer of the pore network, which plays a crucial role in the interaction of the stone with condensed atmospheric water. In this work a correlation was found between the extent of surface modification, as determined by streaming current measurements, surface wettability and capillary water absorption of 6 coating-lithotype combinations (3 lithotypes and 2 nanocomposites).

This paper analyzes the measurement error, caused by the position of the current-carrying conductor, of circular array of magnetic sensors for current measurement. The circular array of magnetic sensors is an effective approach for AC or DC non-contact measurement, as its low cost, large linear range, wide bandwidth, light weight and low noise. Especially it has claimed that such structure has the excellent reduction ability for the errors caused by the position of the current-carrying conductor, crosstalk current interference, shape of the conduction cross section and the earth magnetic field. However, the positions of the current-carrying conductor, including un-center and un-perpendicularity, has not analyzed in detail until now. In this paper, the theoretical analysis has been proposed based on vector inner and exterior product. In the presented mathematical model of relative error, the un-center offset distance, the un-perpendicular angle, the radius of the circle and the number of the magnetic sensor are expressed in one equation. The comparison of the relative error caused by the position of the current-carrying conductor between four and eight sensors is conducted. The Tunnel Magnetoresistance (TMR) sensors are used in the experimental prototype to verify the mathematical model. The analysis results can be the reference to design the detail of circular array of magnetic sensors for current measurement in practical situation.

Current-quark masses are compared to the rest masses allowed by the Helmholtz equation in a polar model. Within the uncertainty of the current u quark mass determination, the current quark mass coincides with the rest mass allowed by the Helmholtz equation in the polar model in accordance with the second root of the zero Neumann function. Current d quark mass coincides with the rest mass calculated in accordance with the third root of the Bessel zero function. On the basis of a comparison of these results with the results obtained earlier for ordinary real particles u and d quarks stability is discussed.

The excitation of the visual system increases with increasing retinal illumination. At the same time, the sensitivity of the system decreases (light adaptation). Higher excitation automatically results in a lower sensitivity. This study investigates whether this parallelism between the excitation and the sensitivity also applies in the dynamic case, that is, during the transition to a higher excitation level after an increase in the retinal illuminance. For this purpose, the courses of the subjective and the electroretinographic threshold during the transitional phase after a step of the adaptation illumination was determined by means of a special light-stimulation apparatus. As a measure of the course of the excitation during this time, the response ERG on the adaptation step was recorded with a special amplifier. The threshold curve always has an overswing, which shows subjectively very strong differences. It can be concluded that the glare caused by a sudden increase in illuminance is subjectively very different. The comparison between the response ERG on the adaptation step and the course of the electroretinographic increment threshold during this time shows a broad agreement between the two courses. It can thus be assumed that the sensitivity of the visual system follows the course of the excitation also in the dynamic case. In addition, the investigation shows that the glare experienced after a step in the illuminance clearly shows great subjective differences.

Chronoamperometric curves of the oxidation of a ferrocenyl derivative by the potential step showed diffusion controlled-like currents less than the Cottrell's equation at a platinum wire electrode. The lower deviation cannot be explained by the Butler-Volmer heterogeneous kinetics, but was ascribed to the negatively capacitive current associated with the redox reaction. The deviation at the fully oxidized potential corresponds to the non-zero concentration at the electrode surface, which cannot be predicted from the Nernst equation. The Nernst equation expresses the relationship of the potential with the activity at the electrode surface rather than the concentration. The diffusion equation provides the relation of the current with the surface concentration rather than the activity. The negative capacitance or the non-zero concentration may arise from structure formation on the electrode owing to the dipole-dipole interaction, which is similar to the generation of the double layer capacitance including frequency dispersion. On this concept, we derive here expressions for the lowered diffusion-controlled current and the time-dependent surface concentration. The negatively capacitive current shows the time-dependence of t-0.9, which is similar to the decay of the double layer capacitive currents. The surface concentration decays with the t-0.4-dependence.

DC-connected parallel inverter systems are gaining popularity in industrial applications. However, such parallel systems generate excess current ripple (harmonics) at the DC-link due to harmonic interactions between the inverters in addition to the harmonics from the PWM switching. These DC-link harmonics cause the failure of fragile components such as DC-link capacitors. This paper proposes an interleaving scheme to minimize the current harmonics induced in the DC-link of such a system. The results show that when the carrier waves of the two inverters are phase-shifted by 90° angle, the maximum high-frequency harmonic ripple cancellation occurs, which reduces the overall RMS value of the DC-capacitor current.The outcome of this proposed solution is a cost-effective DC-harmonics mitigating strategy for the industrial designers to practically configuring multi-inverter systems, even when most of the drives are not operating at rated power levels. Experimental and simulation results presented in this paper verify the effectiveness of the proposed carrier-based phase-shifting scheme for two different configurations of common DC connected multi-converter systems.

When grid-following (GFL) and grid-forming (GFM) converters are interconnected with the grid, they are mutually coupled through the grid impedance. During grid faults, the transient behavior of these converters becomes intricate due to the presence of coupling terms. Instabilities in one converter can propagate to the other, posing challenges to fault ride-through capability. Firstly, a mathematical model was presented for a hybrid grid-tied system comprising two converters, investigated the conditions for equilibrium points, and employed phase-plane analysis to elucidate the mutual influence mechanism during faults. Then, a method to adjust the power angle of GFM according to the voltage drop was proposed and used in GFL to improve its phase-locked loop. At the same time, considering the influence of GFL current injection, the fault current of GFM was limited, so as to realize the hybrid fault ride-through control. The proposed approach ensures that GFM converters contribute reactive current support to the grid during faults, while GFL converters adhere to grid guidelines for current injection, thereby preventing overcurrent and phase angle instability in both converters. Finally, simulation results validated the correctness and effectiveness of the proposed control strategy.

Zr-2.5%Nb Pressure tubes (PT) house uranium fuel bundles in the fuel channels of CANDU® nuclear reactors. Preventing a failure mode caused by contact of the PT with an outer calandria tube (CT) is performed by inspection using eddy current (EC) testing and ultrasonic testing (UT) to measure the PT-CT gap. EC gap measurements are particularly sensitive to circumferential variation of the PT’s electrical resistivity, due to microstructural variations. A full-factorial experiment was performed to examine the statistical significance of variations in EC test parameters and manufacturing conditions on average circumferential electrical resistivity of as-manufactured PTs. It was found that 79% of the variance in the data could be attributed to variations caused by any of the test factors or combinations of test factors. The parameters that accounted for the majority of the variance were; 1) heat treatment (HT); 2) HT and EC frequency; 3) probe inner or outer surface placement; and 4) EC frequency. Measurements of circumferential resistivity showed up to ± 2.3% variation from the average of either surface. HT caused average PT resistivity to decrease at a rate of 1.53±0.08 (μΩ⋅cm)/log⁡(hr) and 1.1±0.4 (μΩ⋅cm)/log⁡(hr) for inner and outer PT surfaces, respectively. Results are correlated with literature reported differences in average β_Zr ribbon thickness in the axial-transverse cross-section between inner and outer PT surfaces. Results demonstrate potential for EC based resistivity measurements to characterize variations and changes in microstructure of Zr-2.5%Nb PT material.

(1) Background: Alzheimer’s Disease (AD) accounts for 70% of dementia cases and with no effective pharmacological treatments, new rehabilitation methods are needed. Motor activities and transcranial direct current stimulation (tDCS) have shown promise in stabilizing and enhancing cognitive functions. Objective: We want to investigate the effects of combined motor or cognitive activity with tDCS on cognitive functions in AD patients. (2) Methods: Patients with mild or moderate AD were randomized into four groups: motor activity or cognitive activity associated with anodic or sham tDCS (MotA, MotS, CogA, CogS). They received two weeks of treatment (45 minutes, 5 days/week), with the first 15 minutes using 2mA tDCS on the dorsolateral prefrontal cortex. Cognitive assessments were conducted pre-treatment (T0), post-treatment (T1), and one week after (T2). (3) Results: Twenty patients were included. Mann-Whitney test showed significant improvements in anodic groups (MotA+CogA) in the global cognitive status (p=.042), in selective attention (p=.012), and sustained attention (p=.012) at T1, but not at T2. In addition, MotA improved in the Picture Recognition Test (p=.027) and in sustained attention (p=.047) at T2. (4) Conclusion: Combined motor or cognitive activity with anodic tDCS could slow cognitive decline in AD patients, with notable improvements in global cognitive state and attention at T1.

Transcutaneous nerve stimulation has several neuromodulatory applications, including pain management, sensory restoration, and motor recovery. Transcutaneous stimulation delivered via electrode arrays offers ease of use and reconfigurability through non-invasive means. Also, employing electrode arrays allows regulation of the permeated electric fields for greater control over the stimulation performance. Field shaping involves the regulation of permeated electric fields and is a well-established practice for deep brain stimulation; however, its applicability to peripheral nerve stimulation still needs exploration. Adopting such techniques can help to overcome current limitations with transcutaneous stimulation, like poor targetability, early onset of fatigue, and perceived discomfort. This article provides a perspective on the applicability of field-shaping techniques in improving the overall stimulation outcome.

The pinning force density FpJc,B=Jc×B (where Jc is the critical current density and B is the applied magnetic field) is one of the main parameters that characterize the resilience of a superconductor to carry a dissipative-free transport current in an applied magnetic field. Kramer (1973 J. Appl. Phys. 44 1360), and Dew-Hughes (1974 Phil. Mag. 30 293) proposed a widely used scaling law for the pinning force density amplitude: FpB=Fp,max×p+qp+qppqq×BBc2p×1-BBc2q, where Fp,max, Bc2, p, and q are free-fitting parameters. Since the late 1970-s till now, several research groups have reported experimental data on the dependence of Fp,max on the average grain size, d, in Nb3Sn-based conductors. Godeke (2006 Supercond. Sci. Techn. 19 R68) proposed that the dependence obeys the law Fp,maxd=A×ln1d+B. However, this scaling law has several problems, for instance, the logarithm is taken from a non-dimensionless variable, and Fp,maxd&lt;0 for large grain sizes, and Fp,maxd→∞ for d→0. Here, we reanalysed the full inventory of publicly available Fp,maxd data for Nb3Sn conductors and found that the dependence can be described by Fp,maxd=Fp,max0×exp-dδ law, where the characteristic length, δ, varies within a remarkably narrow range, that is, δ=175±13 nm, for samples fabricated by different technologies. The interpretation of the result is based on the idea that the in-field supercurrent flows within a thin surface layer (thickness of δ) near the grain boundary surfaces (similar to London’s law, where the self-field supercurrent flows within a thin surface layer with a thickness of the London penetration depth, λ, and the surface is a superconductor-vacuum surface). An alternative interpretation is that δ represents the characteristic length of the exponential decay flux pinning potential from the dominant defects in Nb3Sn superconductors, which are grain boundaries.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

Stray current is a relevant phenomenon in particular for DC electrified transportation systems, affecting the track and infrastructure within the right of way and other structures and installations nearby. It worsens with time and the level of protection depend on timely maintenance, besides correct design choices. The assessment of track insulation is the starting point for both stray current monitoring systems and at commissioning or upon major changes. Standardized methods (ref. EN 50122-2, or IEC 62128-2) are almost unchanged in the last 20 years, but suffer from accuracy issues and variability due to parameters and conditions not under operator’s control. A critical discussion and analysis of the sources of variability and practical constraints is proposed, followed by the evaluation of uncertainty, with the objective not only to assess the accuracy of provided results, but to foster research on innovative, more flexible and accurate, methods.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

This paper reports the effect of silicon substrate orientation and aluminum nitride buffer layer deposited by molecular beam epitaxy on the growth of aluminum nitride thin films deposited by DC magnetron sputtering technique at low temperature. The structural analysis has revealed a strong (0001) fiber texture for both substrates Si (100) and (111) and a hetero-epitaxial growth on few nanometers AlN buffer layer grown by MBE on Si (111) substrate. SEM images and XRD characterization have shown an enhancement in AlN crystallinity thanks to AlN (MBE) buffer layer. Raman spectroscopy indicated that the AlN film was relaxed when it deposited on Si (111), in compression on Si (100) and under tension on AlN buffer layer grown by MBE/Si (111) substrates, respectively. The interface between Si (111) and AlN grown by MBE is abrupt and well defined; contrary to the interface between AlN deposited using PVD and AlN grown by MBE. Nevertheless, AlN hetero-epitaxial growth was obtained at low temperature (<250°C).

A new picture of the Josephson effect is devised. The radio-frequency (RF) signal, observed in a Josephson junction, is shown to stem from bound electrons, tunneling periodically through the insulating film. This holds also for the microwave mediated tunneling. The Josephson effect is found to be conditioned by the same prerequisite worked out previously for persistent currents, thermal equilibrium and occurence of superconductivity. The observed negative resistance behaviour is shown to originate from the interplay between the normal and superconducting currents.

The Chile-Peru subpopulation (CPe) of the southern right whale (Eubalaena australis) is classified as critically endangered following intense whaling in past centuries. Due to their very low abundance, information on breeding and feeding grounds is also scarce. Unmanned aerial vehicles (UAVs) are increasingly applied in marine mammal research thanks to their low cost and relative ease of use. This case study documents a southern right whale nursing in Bahía Moreno (23ºS), Antofagasta, northern Chile, through high-resolution images taken by UAV of a lone adult in July 2019 and the same (photo-identified) whale with a neonate in August, confirming local parturition. Combined with earlier data we hypothesize that the Antofagasta Region may be a calving and nursing ground for the CPe subpopulation. Given the intense shipping traffic and fishing activities around the Mejillones Peninsula and Antofagasta port, priorly recommended marine spatial planning to help avoid net entanglements and vessel collisions of fin and humpback whales would also contribute to the conservation of the CPe stock of southern right whale.

In this work, it is analyzed a Digital Signal Processor, DSP, based One Cycle Control, OCC, strategy for a Power Factor Corrector, PFC, rectifier, which presents Common-mode Voltage, CMV, immunity. The proposed strategy utilizes an emulated-resistance-controller in closed-loop configuration to set up dc-link voltage and achieve unity power factor, UPF. It is shown that if PFC can achieve UPF condition and if phase voltage is only affected by CMV, then phase current is free from CMV, as well as a lead-lag compensator, LLC, to average phase current. Another possible condition is also analyzed. The proposal is verified by simulation and experiments.

The eddy current loss should be optimized to be as less as possible for the stability of permanent magnet in high speed permanent magnet synchronous motor (HSPMSM) rotor and ensure the high efficiency and low temperature of the motor. This paper analyzes the eddy current distribution in rotor, with consideration of the conflict of the thickness of sleeve and diameter of the rotor, calculating the eddy current loss (ECL) and the thermal distribution via Separation of variables method for solving Maxwell's equations with analytical hieratical model of ECL constructed. The optimization result of ECL of the HSPMSM whose power and rated speed is 30kw 48000r/min can be got by multi-objective optimization method, combined weighting coefficient method and traversal algorithm based on chaotic local search particle swarm optimization (CLSPSO), utilizing ECL analytical model and other analytical constraints. Related experiment and measurement has been implemented with new approach of loss separation.

In this study, we applied a central composite design to estimate independent variables and establish optimal conditions of filtration rate and feces production that enhance filtration of suspended organic matter by the freshwater mussels Sinanodonta woodiana. The results indicated that statistical design methodology offers an efficient and feasible approach for high filtration and low feces production condition optimization. The proposed model equation takes into account the quantitative effect of variables and also the influence of interactions among variables on mussel filtration rate. Under the optimal experimental conditions (mussel size, 13.0 ± 0.2 cm; water current, 17.5 L/h), the experimental filtration rate of 4.47 ± 1.82 L/mussel/h showed a degree of correspondence with the predicted value of 8.4 L/mussel/h, which verified the practicability of this optimum strategy.

Building a new power plant to address the growing demand for power due to population concentration in the metropolitan area is one of the world's major concerns. However, since a large power plant can not be located around the city due to burden of economic cost, building power plant outside metropolitan and cities is necessary. Therefore, new power generation facilities are promoting policies to provide distributed generator(DG) with a small capacity relatively near the metropolitan. When the DG (photovoltaic, wind farm, etc.) is connected with the grid using medium voltage direct current (MVDC) system, voltage sourced converter(VSC) should supply reactive power to the grid, because of fault ride through(FRT) operation in grid fault. If the voltage drop is severe, the converter should be disconnected from the grid immediately without supplying the reactive power, resulting in a considerable economic loss. In general, superconducting fault current limiter(SFCL) is introduced as a measure to enhance FRT capability. In this paper, we use trigger type SFCL which protects superconducting element and reduces low voltage. On the other hand, the active power unbalance of the DC-link and the DC voltage rise due to the reactive power supply of the grid-side converter. The rise of the DC voltage causes the P (active power), Q (reactive power) control of the converter to deviate, causing malfunction and damage of the DC equipment. Therefore, the rise of the DC voltage must be prevented. In this paper, we consider the suppression the DC voltage rising caused by the FRT operation through the active power tracking control (APTC).

In the context of energy conversion from renewable sources to distribution grids (insulated or not), a converter is often required to transfer energy from a low voltage source, towards three-phase grids. This paper presents the HW design, the simulation results and the conversion performance of a CSI converter intended to interface low voltages renevable sources to three-phase grids. The main focus of this paper is to obtain the best performance in terms of voltage increase towards the output stage while maximizing the conversion efficiency. In comparison with the currently used energy conversion systems for small photovoltaic systems, hereafter some solutions were adopted to level and maximize the energy flow from the source to the DC-link and improve the quality of current supplied in terms of harmonic distortion. The proposed system is composed of two conversion stages: the first, voltage-to-current, the second current-to-current via a three-phase CSI bridge modulated with SVM technique. The stages are not completely decoupled from an electrical point of view, therefore, in order to mitigate the effects of these interactions, synchronization strategies have been adopted.

Additive Manufacturing (AM) Direct Laser Fabrication (DLF) of Ti-5Al-5V-5Mo-3Cr (Ti5553) is being developed as a method for producing aircraft components. The additive manufacturing process can produce flaws near the surface, such as porosity and material voids, which act as stress raisers, leading to potential component failure. Eddy current testing was investigated to detect flaws on or near the surface of DLF Ti5553 bar samples. For this application, the objective was to develop an eddy current probe capable of detecting flaws 500 µm in diameter, located 1 mm below the component's surface. Two initial sets of coil parameters were chosen: The first, based on successful experiments that demonstrated detection of a near surface flaw in Ti5553 using a transmit-receive array probe, and the second, derived from simulation by Finite Element Method (FEM). An optimized transmit receive coil design, based on the FEM simulations, was constructed. The probe was evaluated on Ti5553 samples containing sub-surface voids of the target size, as well as samples with side-drilled holes and samples with holes drilled from the opposing inspection surface. The probe was able to effectively detect 80% of the sub-surface voids. Limitations included the probe’s inability to detect sub-surface voids near sample edges and a sensitivity to surface roughness, which produces local changes in lift-off. Multifrequency mixing improved signal-to-noise ratio when surface roughness was present on average by 22%. A probe based on that described in this paper could benefit quality assurance of additively manufactured aircraft components.

Adjustable frequency converters are widely used in modern automated asynchronous drives due to their high efficiency and high responsiveness control strategies. Control algorithms for frequency converters are divided into two main groups: constant frequency commutation and random frequency commutation. Research results on various commutation frequencies, conducted using Matlab/Simulink software, show that the use of random frequency commutation provides better efficiency by significantly reducing the amplitude of harmonic oscillations at different frequencies, with a reduction in switching losses in transistors. Currently, a converter with random frequency commutation is being researched and applied in the direct torque control system. The traditional direct control system, based on a two-level inverter, is widely used due to its simplicity and ease of implementation. However, this method results in the output current of the two-level converter, supplied to the motor stator, having many harmonic distortions, leading to strong torque fluctuations regardless of the rotation speed and ultimately causing additional losses in the stator windings and reducing the motor's lifespan. To enhance the efficiency of automated asynchronous drives, this article presents an algorithm for a direct control system based on a three-level NPC inverter using a PI speed regulator. The proposed algorithm's research is validated in the Matlab/Simulink environment. The research results show that in the absence of harmonic filtering, the stator current harmonic distortion coefficient is approximately 11%, and torque fluctuations are less than 5% of the resistive torque. The fluctuations between the two capacitors remain almost unchanged throughout the entire process.

The three-dimensional structure of Gulf of Mexico’s warm-core rings, detaching from the Loop Current, is investigated using satellite altimetry and a large set of ARGO float profiles. Reconstruction of the Loop Current rings (LCRs) vertical structure from sea surface height observations is made possible by the use of the gravest empirical modes method (GEM). The GEMs are transfer functions that associate a value of temperature and salinity for each variable pair {dynamic height;pressure}, and are computed by estimating an empirical relationship between dynamic height and the vertical thermohaline structure of the ocean. Between 1993 and 2021, 40 LCRs were detected in the altimetry and their three-dimensional thermohaline structure was reconstructed, as well as a number of dynamically relevant variables (geostrophic and cyclogeostrophic velocity, relative vorticity, potential vorticity, available potential energy and kinetic energy density etc.). The structure of a typical LCR was computed by fitting an analytical stream function to the LCRs dynamic height signature and reconstructing its vertical structure with the GEM. The total heat and salt contents and energy of each LCR were computed and their cumulative effect on the Gulf of Mexico’s heat, salt and energy balance is discussed. We show that LCRs have a dramatic impact on these balances and estimate that residual surface heat fluxes of -13 Wm−2 are necessary to compensate their heat input, while the fresh water outflow of the Mississippi river approximately compensates for their salt excess input. An average energy dissipation of O[10−10−10−9] Wkg−1 would be necessary to balance their energy input.

The energy potential of long-period oscillations is estimated by comparing it with watercourse power. The relaxation time of long-period waves is chosen for the estimation time interval, during which their amplitude decreases e (Euler's number) times from the initial one. According to calculations, the amount of energy produced during this time by the watercourse is 9.35–18.71 million kW×h, while the amount of energy of long-period oscillations is 3–6 times less – 1.60–5.48 million kW×h. The components of the economic factor of using long-period waves and currents for electricity production are the predictability of their magnitudes and location of maxima, long-term availability, concentration.

Null-flux Electro-dynamic suspension (EDS) system promises to be one of the feasible high-speed maglev systems above 600 km/h. On account of its greater current-carrying capacity, superconducting magnet can provide super-magnetomotive force that is required for null-flux EDS system and cannot be provided by electromagnets and permanent magnets. There is already a relatively mature high-speed maglev technology with low temperature superconducting (LTS) magnets as the core, which works in the liquid helium temperature region (T≤4.2 K). 2-Generation high temperature superconducting (HTS) magnet winded by REBa2Cu3O7−δ (REBCO, RE=rare earth) tapes works above 20 K region and do not need to count on liquid helium which is rare on earth. This paper designed HTS no-insulation closed-loop coils applied for EDS system and energized with persistent current switch. The coils can work at persistent current model and has premier thermal quench self-protection. Besides, a full size double-pancake module was designed and manufactured in this paper, and it was tested in liquid nitrogen. The double-pancake module’s critical current is about 54 A and it is capable of working at persistent current model, whose average decay rate measured in 12 hours is 0.58%/day.

To clarify the relationships among critical temperature, critical magnetic field, and critical current density, this paper describes many-body interactions of quantum magnetic fluxes (i.e., vortices) and calculates pinning-related critical current density. All calculations are analytically derived, without numerical or fitting methods. Afteralculating a magnetic flux quantum mass, we theoretically obtain the critical temperature in a many-body interaction scenario (which can be handled by our established method). We also derive the critical magnetic field and inherent critical current density at each critical temperature. Finally, we determine the pinning-related critical current density with self-fields. The relationships between the critical magnetic field and critical temperature, inherent critical current density and critical temperature, and pinning critical current density and temperature were consistent with experimental observations. From the critical current density and critical magnetic field, we clarified the magnetic field transition. It appears that a magnetic flux quantum collapses when the lattice of magnetic flux quanta melts. Our results, combined with our previously published papers, provide a comprehensive understanding of the transition points in high-T_c cuprates.

Eddy current testing can be used to interrogate steels but it is hampered by the lift-off distance of the sensor. Previously, the lift-off point of intersection (LOI) feature has been found for the pulsed eddy current (PEC) testing. In this paper, a lift-off invariant inductance (LII) feature is proposed for the multi-frequency eddy current (MEC) testing, which merely targets the ferromagnetic steels. That is, at a certain working frequency, the measured inductance signal is found nearly immune to the lift-off distance of the sensor. Such working frequency and inductance are termed as the lift-off invariant frequency (LIF) and LII. Through simulations and experimental measurements of different steels under the multi-frequency manner, the LII has been verified to be merely related to the sensor parameters and independent of different steels. By referring to the LIF of the test piece and using an iterative inverse solver, one of the steel properties (either the electrical conductivity or magnetic permeability) can be reconstructed with a high accuracy.

Chronology unprotected mechanisms are considered with a very low gravitational polarization to make the wormhole traversal with positive energy density everywhere. No need of exotic matter has been considered with the assumption of the Einstein-Dirac-Maxwell Fields, encountering above the non-zero stress-energy-momentum tensor through spacelike hypersurfaces by a hyperbolic coordinate shift.

Humpback whales perform long migrations from their breeding and nursing areas at low latitudes to feeding grounds at high latitudes. Nonetheless this strictly dichotomous paradigm of migration is challenged by accumulating examples of occasional or regular feeding in tropical or subtropical areas for several stocks worldwide. Here we report multiple lines of evidence of IWC ‘Stock G’ humpback whales feeding in coastal waters at low latitudes of the Southeast Pacific Ocean. Lunge-feeding behavior was observed in Ecuador, while both lunge- and trap-feeding in pursuit of Peruvian anchovy was documented in northern Chile. Five records of substantial defecation in a key breeding ground in Ecuador also demonstrates local foraging. In addition mark-recapture analysis of one individual feeding at high and mid latitudes of Chile suggested potential site fidelity to two foraging areas. Whether these behaviors are novel due to changes in prey distribution, intensifying competition for food from a growing humpback whale population, or rather reflect vastly increased research effort in a poorly studied region, remains unknown. Further research into the feeding ecology of 'Stock G' should help reveal historic and potentially novel feeding grounds, prey composition and precise migration paths.

In view of the preparation for a post-LHC collider, the high-energy physics (HEP) community started from 2010 to discuss various options, including the use of HTS for very high field dipoles. Therefore, a small program was set in Europe aiming at exploring the possibility of using HTS for accelerator quality magnets. Based on various EU funded programs, though at modest levels, has enabled the European community of accelerator magnets to start getting experience in HTS and addressing a few issues. The program was based on use of REBCO tapes to form 10 kA Roebel cables, to be used to wind small dipoles of 30-40 mm aperture in the 5 T range. The dipoles are designed to be later inserted in a background dipole field (in Nb3Sn), to reach eventually a field level in the 16-20 T range, beyond the reach of LTS. The program is currently underway: more than 1 km tape of high performance (Je &gt; 500 A/mm2 at 20 T, 4.2 K has been manufactured and characterized, various 30 m long Roebel cables have been assembled and validated up to 13 kA, a few dipoles have been wound and tested, reaching at present 4.5 T in stand-alone (while a dipole made from race track coils with no-bore exceeded 5 T using stacked tape cable) and a test in a background field is being organized.

Two opposed p–n diodes are connected with another junction that causes cancellation of the electric field in the depletion layer of each diode by the field of the other diode. This derived quantum diode is called the A system. Another dual diode, constructed by the same process but with the p- and n-types positioned as duality, called the B system. When a bias voltage is applied between the A and B systems, Lorentz conservation imparts a momentum (i.e., a wave number) to the carriers in the absence of any internal voltage. Thus, a superconducting bias current density appears without the need for cooling. The reappearances of electron–hole pairs on the junction surfaces are assumed to be described by entire wavefunctions normalized by the band gap. Based on the bias superconducting current, NOT and NAND gates were constructed from the quantum diode systems. Numerical calculations revealed that the constant phases of the entire wavefunctions of the p-and n-types converged. Accordingly, it was clarified that Bose–Einstein condensation and the Meissner effect (described by the London equation) occurred in the quantum diode systems. Moreover, the systems exhibited rectification characteristics and a switching speed of the order of 10^-14 s. Combining this switching property with the large bias superconducting current (of the order of several V), we developed NOT and NAND gates with direct quantum correlations among many qubits, which are unaffected by random and thermal noises. These gates have memorization and initialization properties and are compatible with existing and accumulating programing algorithms. Moreover, when harvesting a divergent current output from these systems, the bias superconducting current and memorization property preserve the formed quantum correlations.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

This paper presents a new approach of eddy current methods for determining the size of the co-axial hole in the metallic circular disk. In recent decades, for the air-cored sensor probe, the impedance change due to the presence of an infinite metal plate can be calculated by the Dodd-Deeds model. However, in practical measurements, the sample cannot match with the condition required - ‘infinite’, thus the Dodd-Deeds model could not be applied to the disk with finite size and certainly not a co-axial hole in the center. In this paper, a dual-constraint analytical method is proposed. That is, the upper and lower limits of the integration are substituted with specific values instead of the original 0 and . Besides, it is found that, once the outer radius of the disk is fixed (i.e. the lower limit of integration is fixed), the upper limit reduces linearly as the size of the coaxial hole increases. Both the FEM simulation and experiments have been carried out to validate this method. The radius of the hole can be estimated based on the dual-constraint integration feature.

Prestrained at 5% and 15% duplex stainless steel UNS S32750 specimens have been subjected to electropulsing treatments with current density of 100 A/mm2 and 200 A/mm2 and 100 and 500 pulses for each current density value. Corrosion tests, X-ray diffraction, microhardness and residual stresses were collected before and after the electropulsing treatments. Tensile tests were performed after the electropulsing treatments in order to compare the mechanical response to the reference tensile tests performed before the pulsing treatments. Increase in fracture strain was observed after the pulsing treatment in comparison to the reference tensile tests. A decrease in microhardness was also observed after the electropulsing treatments for both degrees of prestrain. Electropulsing treatment almost eliminates the work-hardened state in the 5% prestrained specimens while partially recovered the 15% prestrained material increasing both uniform and fracture strain. The bulk temperature of the samples remained the same for all the duration of the treatments. The effect are to be addressed to a combined effect of the increase in atomic flux due to the electrical current and local joule heating in correspondence of crystal defects. Electropulsing treatment applied to metallic alloys is a promising technique to reduce the work hardening state without the need of annealing treatments in a dedicated furnace.

The purpose of this paper is to explore which financial performance indicators (FPIs) evaluate the level of supply chain capability (SCC) that explicitly touches all of the business functions and processes within and beyond the company. The authors investigated nine FPIs that were selected from the financial statements of 155 companies within nine industries. The authors find that suitable FPIs to measure SCC for shareholders’ value are return-on-assets (ROA), days-sales-outstanding (DSO), and current ratio (CR). This means that higher ROA, shortened DSO, and an appropriate level of CR could reach a sustainable supply chain. These results will help the industry to avert a major disruption in supply chain processes and activities using suitable financial performance indicators.

The characterization of thin-film solar cells is of huge importance for obtaining high open-circuit voltage and low recombination rates from the interfaces or within the bulk of the main materials. Among the many electrical characterization techniques, the two- and four-wire probe using the Cascade instrument is of interest since the resistance of the wires, and the electrical contacts can be excluded by the additional two wires in 4-wire probe configuration. In this paper, both two and four-point probes configuration are employed to characterize the CIGS chalcogenide thin-film solar cells. The two-wire probe has been used to measure the current-voltage characteristics of the cell which results in a huge internal resistance. Therefore, the four-wire connection is also used to eliminate the lead resistance to enhance the characterization’s accuracy. The load resistance in the two-wire probe diminishes the photogenerated current density at smaller voltage ranges. In contrast, the proposed four-wire probe collects more current at higher voltages due to enhanced carrier collection efficiency from contact electrodes. The current conduction mechanism is also identified at every voltage region represented by the value of the ideality factor of that voltage region. It is observed that a long time given to the charge collection results in increased current density at a higher voltage. According to the results and device characteristics, a novel double-diode model is suggested to extract the saturation current density, shunt and series resistances and the ideality factor of the cells. These cells are shown to be efficient in terms of low recombination at the interfaces and with lower series resistance as the quality of the materials is in its most possible conductive form. The measured internal resistance and saturation current density and ideality factor of the two measurement configuration is measured and compared.

We construct families of ground state representations of the U(1)-current net and of the Virasoro nets Vir_c with central charge c ≥ 1. We show that these representations are not covariant with respect to the original dilations, and those on the U(1)-current net are not solitonic. Furthermore, by going to the dual net of with respect to the ground state representations of Vir_c, one obtains possibly new family of Möbius covariant nets on S¹.

A computational methodology for the hydrodynamic analysis of horizontal axis marine current turbines is presented. The approach is based on a boundary integral equation method for inviscid flows originally developed for marine propellers and adapted here to describe the flow features that characterize hydrokinetic turbines. To this purpose, semi-analytical trailing wake and viscous-flow correction models are introduced. A validation study is performed by comparing hydrodynamic performance predictions with two experimental test cases and with results from other numerical models in the literature. The capability of the proposed methodology to correctly describe turbine thrust and power over a wide range of operating conditions is discussed. Viscosity effects associated to blade flow separation and stall are taken into account and predicted thrust and power are comparable with results of blade element methods that are largely used in the design of marine current turbines. The accuracy of numerical predictions tend to reduce in cases where turbine blades operate in off-design conditions.

A three-dimensional, unstructured grid, hydrodynamic and suspended-sediment transport model (i.e., SELFE-SED) was developed to simulate temporal and spatial variations of suspended sediment and was applied to the subtropical subalpine Tsuei-Feng Lake (TFL) of Taiwan. The model was validated with measured water level and suspended‑sediment concentration in 2009, 2010, and 2011. The overall model simulation results are in quantitative agreement with the observational data. The validated model was then applied to explore the most important parameter that affects the suspended-sediment concentration and to investigate the effect of wind stress on the mean current and suspended‑sediment distribution in this shallow lake. Modeling results of sensitivity analysis reveal that the settling velocity is a crucial parameter and erosion rate is less important in the suspended-sediment transport model. Remarkable lake circulation was found based on the strength of wind speed and wind direction. Strong wind would result in higher mean current in the top layer and suspended-sediment distribution in the top and bottom layers. This study demonstrated that the wind stress played a significant influence on mean circulation and suspended-sediment transport in a shallow lake.

This paper examines the control challenges faced by underactuated Autonomous Underwater Vehicles (AUVs) under ocean current disturbances. It proposes a Backstepping Integral Sliding Mode Control (BISMC) strategy to enhance their adaptability and robustness. The BISMC strategy integrates the system decomposition capability of the Backstepping Control method with the rapid response and robustness advantages of the Sliding Mode Control method, enabling the design of a heading controller and a double closed-loop depth controller. By introducing an integral component, the strategy eliminates steady-state errors caused by ocean currents, accelerating system convergence and improving accuracy. Furthermore, a saturation function is employed to mitigate output chattering issues. Simulation results demonstrate that the BISMC controller significantly enhances the control precision and anti-disturbance capabilities of AUVs under low-frequency ocean current disturbances, showcasing exceptional adaptive and self-disturbance rejection performance.

Wide-bandgap tin oxide (SnO₂) thin-films are frequently used as an electron-transporting layers in perovskite solar cells due to superior thermal and environmental stabilities. However, its crystallization by conventional thermal methods requires typical temperatures between 300 and 900 ◦C [1] with up-to 60 min crystallization times. These post-processing conditions severely limit the choice of substrates and reduce the large-scale manufacturing capabilities. This work describes the intense pulsed light-induced crystallization of SnO₂ thin films using only 500 μs of exposure time. Thin-film properties are investigated using both impedance spectroscopy and photoconductivity characteristic measurements. Nyquist plot analysis establishes that the process parameters have a significant impact on the electronic and ionic behaviors of the SnO2 films. Most importantly, we demonstrate that light-induced crystallization yields improved topography and excellent electrical properties through enhanced charge transfer, improved interfacial morphology and better ohmic contacts compared to thermally-annealed SnO₂ films.

The world is currently facing an energy crisis. To solve the problem, many countries have been exploring renewable energy sources. However, the existing renewable energy sources are highly dependent on weather changes, necessitating the utilization of significantly expensive and large storage batteries.As a solution, we propose a system for generating renewable energy. The proposed system comprises a current source and a voltage source connected in series. With appropriate adjustments, the current source supplies current without voltage and the voltage source provides voltage without current. Considering that electric power is a product of current and voltage, electric power is generated from the interaction between the current source and voltage source. In our previous study, the same result was obtained; however, the output voltage was low, which resulted in a low amount of generated energy. In this study, by introducing some ingenuities, we successfully increased the output voltage. Consequently, we succeeded in powering a light-emitting diode and charging a super-condenser to the standard voltage. Using this system, we generated a relatively large amount of energy in the right place and at the right time, validating our systems’ robustness to changes in weather. The large-scale adoption of our system could contribute to solving the global energy crisis.

Photovoltaic modules should pass series of tests and examinations, verifying the electrical and thermal characteristics of the module, before being released to the market, examining the properties of the modules should undergo appropriate durability and efficiency tests under real outdoor conditions with exposure to climatic conditions and under laboratory conditions. The performance of photovoltaic cells depends on many factors, such as solar irradiance, module operating temperature, installation location, weather conditions and module shading. In this paper, three selected photovoltaic modules were examined using a large-scale steady-state solar simulator. The current-voltage (I-V) characteristics of the photovoltaic modules were experimentally tested and analyzed. The next step was to implement a three-layer artificial neural network model (MLP). The experimental data obtained in the previous step coupled with output data from MLP were then used in global sensitivity analysis (GSA). Experiments carried out on a large-scale stationary solar simulator showed differences between the values declared by the manufacturer and the values obtained from measurements of PV modules. The first module tested achieved the maximum power point greater than that specified by the manufacturer, while the other two showed power drops; it was 85-87% for the second module, and 95-98% for the third, respectively. The performed global sensitivity analysis (GSA) for the MLP model showed that the parameters: eff (22.9) and Voc/V (14.19) have the largest effect on the power-voltage relationship, while U (7.29) has the smallest effect. The usefulness of machine learning (ML) methods in the comparative analysis of PV modules has been proved.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

The presence of escaped fish in aquaculture facilities as a result of harsh meteorological conditions (more pressing in a face of climate change) requires a better understanding of these dynamical behaviour through vigilant monitoring and validated numerical models. In this context, data from strain, stress sensors as well as meteorological and current sensors installed at an aquaculture farm in the Region of Murcia (Spain) were collected, processed and analysed. Among them, first results about the relationship between load and currents sensors are presented. Due to the complexity of the time series, various analyses were conducted to examine their interrelation, encompassing regression analysis of raw data and data segmented into different time intervals. Through this analysis, it was observed that employing distinct time windows better elucidated the data variability. Furthermore, an optimal data window of 240 data was identified, demonstrating significantly improved explanatory power, with the coefficient of determination (R2) increasing by approximately 0.8 depending on the section. This pave the way for optimizing the monitoring features that must be carried out to relate cause-and-effect variables in the behaviour of these off-shore infrastructures.

This study focuses on the modification of ion-exchange membranes by incorporating phosphorylated dendrimer into sulfonated polytetrafluoroethylene membranes to enhance specific selectivity between mono-/divalent ions, using the Ca2+/Na+ pair as an example. The research employs mechanical, physico-chemical, and electrochemical analyses to explore the effects of P-H20 incorporation on membrane properties. Bulk modification significantly increases membrane selectivity towards calcium ions (specific permselectivity coefficient rises from 1.5 to 7.2), while maintaining the same level of the limiting current density. Other findings indicate that bulk modification significantly changes the transport-channel structure of the membrane and alters the mechanism of over-limiting mass transfer. The over-limiting current for the pristine membrane is mainly due to non-equilibrium electroconvection, while modified membranes actively participate in the water-splitting reaction, leading to the suppression of the electroconvection. Despite this drawback, the decrease of the over-limiting potential drop results in a decrease in specific energy consumption from 0.11 to 0.07 kWh/mol. In the under-limiting current mode, the specific energy consumption for all studied membranes remains within the same limits of 0.02-0.03 kWh/mol.

We report on the study of the temperature dependence of the response of a BSO crystal based polarimetric current sensor with spectral interrogation. Two possible interrogation schemes are discussed. The spectral dependence of the optical rotation along the crystal caused by temperature and current changes has been investigated and approximate dependences for the sensitivities to current SI and temperature ST have been derived. A mixed term in the response with spectral interrogation has been revealed, the elimination of which is done by tracking wavelength shifts of two distinct extrema in the polarimetric response. A temperature independent second degree equation for the current changes as a function of the spectral shifts has been derived and tested.

The functional and neurophysiological distinction between dorsal and ventral hippocampus affects also GABAergic inhibition. In line with his notion, ventral CA1 pyramidal cells displayed a more dynamic and effective response to inhibitory input compared to their dorsal counterparts. We posit that this difference is effected by the dorsal-ventral gradient of activin A, a member of the transforming growth factor-β family, which is increasingly recognized for its modulatory role in brain regions involved in cognitive functions and affective behavior. Lending credence to this hypothesis, we found that in slices from transgenic mice expressing a dominant-negative mutant of activin receptor IB (dnActRIB), inhibitory transmission was enhanced only in CA1 neurons of dorsal hippocampus, where basal activin A level is much higher than in ventral hippocampus. We next asked how a rise in endogenous activin A would affect GABAergic inhibition along the longitudinal axis of the hippocampus. We performed ex vivo recordings from wild type and dnActRIB mice after overnight exposure to an enriched environment (EE), which engenders a robust increase in activing A levels in both dorsal and ventral hippocampi. Compared to control mice from standard cages, the behaviorally induced surge in activin A produced a decline in ventral inhibition, an effect that was absent in slices from dnActRIB mice. Underscoring the essential role of activin in the EE-associated modulation of ventral inhibition, this effect was mimicked by acute application of recombinant activin A in control slices. In summary, both genetic and behavioral manipulations of activin receptor signaling affected the dorsal-ventral difference in synaptic inhibition, suggesting that activin A regulates the strength of GABAergic inhibition in a region-specific fashion.

Porous ferroelectric lead zirconate-titanate (PZT) films are a promising material for various electronics applications. This study focuses on understanding how structure-directing agent (polyvinylpyrrolidone) can change structure and electrical properties of porous PZT films prepared by chemical solution deposition. The films with various porosity up to ~ 40 vol.% and pore connectivity changing from 3-0 to 3-3 were prepared and studied by capacitance-voltage, dielectric hysteresis, transient current, photocurrent, and local current techniques. We have found that the linear decrease in the material volume in a porous film is not the only factor governing film properties. The key role in changing electrical properties plays the creation of new internal grain boundaries. This research expands the understanding of physical phenomena in porous ferroelectric films and may enable the development of new materials and devices.

In this paper, based on the pseudo-totem pole (PTP) circuit, a family of five-level PTP dual boost converters (PDBC) is proposed. Dual boost converter has some unique advantages such as no bridge arm shoot-through risk and no switch body diode reverse recovery problem, so that it has a good application prospect. Compared with conventional three-level PTP converters, PDBCs has higher power density, higher efficiency, and low voltage and current stress. The topological derivation process, working principle, modulation and strategy of the topology are analyzed firstly. Further, the number of power devices, the switches voltage and current stress of the proposed topology is analyzed. Finally, a representative five-level PDBC experimental prototype is designed with AC input 220V/50Hz, DC output 400V/1kW, and peak efficiency of 98.27%. The experimental results show that the five-level PDBC proposed in this paper has higher efficiency and verify the correctness of the topology.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Aphasia is one of the most socially disabling post-stroke deficits. Although traditional therapies have been shown to induce adequate clinical improvement, aphasic symptoms often persist. Therefore, new rehabilitation techniques which act as a substitute or as an adjunct to traditional approaches are urgently needed. The present review provides an overview of the efficacy and safety of the most innovative approaches which have been proposed over the last twenty years. First, we examined the effectiveness of the pharmacological approach, principally used as an adjunct to language therapy, reporting the mechanism of action of each single drug for the recovery of aphasia. Results are conflicting but promising. Secondly, we discussed the application of Virtual Reality (VR) which has been proved to be useful since it potentiates the ecological validity of the language therapy by using virtual contexts which simulate real-life everyday contexts. Finally, we focused on the use of Transcranial Direct Current Stimulation (tDCS), both discussing its applications at the cortical level and highlighting a new perspective, which considers the possibility to extend the use of tDCS over the motor regions. Although the review revels an extraordinary variability among the different studies, substantial agreement has been reached on some general principles, such as the necessity to consider tDCS only as an adjunct to traditional language therapy.

This paper presents a concise exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the development of each method. To evaluate the performance of these methods, MATLAB-based software has been developed and deployed to synthesize the results of each method when used to extract the SDM parameters of various PV test modules of different PV technologies. Similar software has also been developed to extract the same parameters using well-established numerical and iterative techniques. A comparison is subsequently made between the synthesized results and those obtained using numerical and iterative methods. The comparison indicates that in spite of the fact that analytical methods may involve fair amount of approximations, their accuracy can be comparable to that of their numerical and iterative counterparts, with the added advantage of significant reduction in computational complexity, and without the initialization and convergence difficulties, which are normally associated with numerical methods.

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

There have been several cases of large-scale wind generators (WGs) tripping off caused by untimely fault removing in recent years. Currently, the discoordination between the box-type transformer fuse protection (BTFP) and two-section collecting line current protection (CLCP) brings a security risk to wind farm. In order to ensure the selectivity, the first section (Sec-I) CLCP should be set a enough interval that is longer than the fuse melting time, and another interval is set for the Sec-II CLCP, which weakens the speed of the CLCP. When a fault occurs on the collecting line, there is no doubt that WGs cannot work too long in abnormal operation, which may cause WGs to be placed off the grid. For a power system with high penetration of wind power, large-scale WGs tripping off will cause a great power shortage, and affect the stability of the power system. The selectivity and sensitivity of the CLCP is analyzed in detail to make the CLCP speed better. Considering the fault ride-through ability of WGs, the fault clear time is an important factor to lead to large-scale WGs tripping off. Two main works are done in this paper. The first is to accelerate the speed of the Sec-I CLCP though reducing the protection zone. Another one is introduce the risk assessment module into the CLCP, which not only improve the speed of the CLCP but also ensure the safety of the wind farm during faults. According to the deference in trip-off causes of WGs, the matching functions are created to assess the trip-off risk of WGs on the spot. In the case of fault, the trip-off risk indicators of WGs are timely updated to data sharing center and open to the CLCPs. The set of risk indicators is divided into several subsets according to the risk range. The dynamic changes of the subsets during fault help to improved CLCP scheme. This scheme can accelerate protection speed based on the increasing risk of large-scale WGs tripping off in wind farms. Compared with traditional CLCP, this approach can make the CLCP combines selectivity and speed better based on the analysis of the ride- through ability of WGs.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Inherent in every Active Magnetic Bearing (AMB) are differences between the expected geometric axes and the actual magnetic axes due to a combination of discrepancies, including physical variation from manufacturing tolerances and misalignment from mechanical assembly, fringing and leakage effects, as well as variations in magnetic material properties within a single AMB. A method is presented here for locating the magnetic axes of an AMB that will facilitate the accurate characterization of the bearing air gaps for potential improvement in field tuning, performance analyses and certain shaft force measurement techniques. This paper presents an extension of the application of the bias current perturbation method for the determination of the magnetic center [4] to the determination of magnetic axes for the further development of accurate current-based force measurement techniques [1].

The high thrust linear motor used for electromagnetic launch is switched with the anti-shunt thyristor as the switch. During the switching process, different current path states will appear, which will lead to changes in motor parameters and current fluctuation. Aiming at the air-core synchronous linear motor with parallel and series power supply, this paper analyzes the change of current path caused by the change of trigger signal of anti-parallel thyristor in the process of sectionalized stator switching. The motor circuit model of the switching process is derived. A new sectionalized stator switching method is proposed to realize the smooth switching of the sectionalized stator powered linear motor. Finally, the correctness of the analysis and modeling is verified by simulation, and the effectiveness of the sectionalized stator switching method is tested by using the test prototype.

The present paper discusses the importance of economic externality and the economic phenomena involved. Section 1 draws on the framework of weak force theory in physics, we propose a new approach of dynamic analysis for economic externality. From a mesoscopic (intermediate scale) perspective, no distinction is made between the macro-demand and individual micro-buyers nor between the macro-supply and individual micro-sellers. Section 2 applies the isospin modeling method to construct two economic isospin models. One is between the achieving impulse and the fear-of-failure impulse, under the effect of economic externality. The other is between the market behavior and market residues, namely, market aftertaste. Section 3 discusses the microstructural properties of the market, including Dirac's equation and the market, Dirac -matrix notation, and the chirality and spin structure of market components. Section 4 discusses the helical structural characteristics of supply chains, including CPT theorems, Penrose zigzag helical processes, and several modeling directions of economic externality and buyer-seller interactions (weak interactions). Section 5 discusses the economic externality and the electroweak model, including extensive externality, externality mediations with Weinberg rotations, and economic analysis using lepton weak currents, including the analysis of lepton neutral weak currents. Finally, Section 6 provides a general discussion on the standard model of economic dynamics.

As the number of end-of-life vehicles continues to grow, the field of separation technology for broken copper and aluminium parts of end-of-life vehicles has emerged as a significant area of research. As a key technology for the separation of non-magnetic non-ferrous metals, such as copper and aluminium, eddy current separation can achieve efficient separation of non-magnetic non-ferrous metals according to their differing conductivity and density. Nevertheless, further research is required in the separation of large-scale broken copper and aluminium parts of end-of-life vehicles. This paper presents a novel magnetic roller model comprising circumferential and axial periodic arrangements of permanent magnets. A single permanent magnet was constructed as an equivalent current model, and the magnetic scalar potential equations were solved using simulation tools. This allowed the distribution of the magnetic field outside the magnetic roller to be studied. The results demonstrate that the novel permanent magnet array magnetic roller can enhance the magnetic field intensity and action distance of the external magnetic field, which is more conducive to the separation of large-scale broken copper and aluminium parts of scrap cars. The findings of this research provide a theoretical foundation for the separation of scrap car broken copper and aluminium parts.

Counter-current spontaneous imbibition of water is a critical oil-recovery mechanism. In the laboratory, the Amott test is a widely used technique to assess efficacy of brine imbibition into oil-saturated core plugs. The classic Amott-cell methodology was designed to estimate ultimate oil recovery, but not the recovery dynamics that provides essential information about the imbibition mechanisms. Retention of oil droplets at the external core surface and delayed onset of oil production are the two key artifacts of the classic Amott experiment. This retention, referred to here as the ``external-surface oil holdup effect'', often results in stepwise recovery curves that obscure true dynamics of spontaneous imbibition. To address these holdup drawbacks of the classic Amott method, we modified the Amott cell and experimental procedure. For the first time, using water-wet Indiana limestone cores saturated with brine and mineral oil, we showed that our improvements of the Amott method enabled accurate and reproducible measurements of oil-recovery dynamics. We used the Generalized Extreme Value (GEV) statistics to describe oil-production histories from water-wet heterogeneous limestone cores with finite initial water saturations, for the first time. We demonstrated that our four-parameter GEV model accurately described the recovery dynamics, and that optimal GEV parameter values systematically reflected the key characteristics of the oil-rock system, such as oil viscosity and rock permeability. These findings gave us a more fundamental understanding of spontaneous, counter-current imbibition mechanisms and insights into what constitutes a predictive model of counter-current water imbibition into oil-saturated rocks with finite initial water saturation.

The fuel cell particularly the Proton Exchange Membrane Fuel Cell (PEMFC) is a new energy technology that plays a critical role in achieving market viability. The PEMFC has high power density, zero CO₂ emissions, and high conversion efficiency. However, with uniform distribution of fuel in PEMFC, we can improve the performance and reduce the cost. The PEMFC will be more efficient and effective in terms of renewable energy as a byproduct only water. Metal foam is used as an alternative for the channels in PEMFC. The model of PEMFC was established by using the ANSYS Fluent 3D Model. Then we proposed four configurations of PEMFC. The outcome demonstrates that Case IV provided outstanding performance if it is compared with the other three cases. In terms of power density, Case IV provided a high power density that is double that of Case I. The porosity of metal foam was investigated. The 0.6 porosity value is found as the optimal value. The uniform distribution of the fuel can be achieved at this value which leads to the outstanding current density.

A hypothesis that the generally accepted value of the LiPON conductivity should be attributed to the absorption and displacement currents is substantiated. The reason is a small contribution of the drift current due to field screening by the electric double layer. The basis for this assumption is the measurement of the LiPON absorption capacitance, according to which its dielectric constant is about 106. An alternative equivalent circuit containing a non-ideal absorption element is proposed and its impedance is calculated. It is shown that the Bode diagrams of the alternative circuit well approximate the experimental curves. Parameters and the magnitude of electric field screening are calculated basing on proposed model of a double electric layer. Considering the screening effect, the drift conductivity of LiPON is obtained, which value is in good agreement with the data on lithium concentration and mobility.

The design of a mixed-mode proportional-integral-derivative (PID) controller circuit using current-feedback operational amplifiers (CFOAs) as active components is proposed. With the same circuit topology, the proposed configuration of three CFOAs, four resistors, and two capacitors is capable of performing the PID controller in all four operation modes: namely voltage mode, trans-admittance mode, current mode, and trans-impedance mode. Numerous mathematical analyses are conducted to determine the controller performance under ideal and non-ideal conditions. Additionally, the mixed-mode second-order lowpass filter is suggested, and also used to examine the workability of the proposed mixed-mode PID controller in a feedback control structure. The proposed PID controller is implemented with the commercially available IC-type CFOA AD844, and the simulation results are presented to illustrate the functionality of the controller and its closed-loop control system.

Exposure to quasi-electrostatic field induced currents is a hazard of live-line transmission work. These steady-state induced currents are typically less than 1 mA, and their sensory effects range from imperceptible to painful depending on the person and conditions such as contact area and duration. Permanent injury from these currents is unlikely but they can distract workers, increasing the risk of injury from falls or other dangers. Identifying contact current severity and training workers can help reduce risk of accidents. Measuring induced currents along a climbing route is time consuming and simulation is challenging because of geometric complexity of the worker, transmission structure, conductor bundles, and electric fields in the climbing space. This research explores calculation of worker contact current using a recently developed adaptation of the charge simulation method. The method uses Fourier principles to improve computational efficiency when explicitly modeling all bundle subconductors. The research also examines reasonable simplifications for modeling lattice structures and human geometry. Calculated results compare well to measured currents for a worker climbing a 400 kV lattice structure. This indicates the method is a practical option for calculating the severity of steady-state contact currents. A simple calculation is suggested for estimating these currents.

Optimizing input parameters not only improves production efficiency and processing quality but also plays a crucial role in the development of green manufacturing engineering practices. The aim of the present study is to conduct a comparative evaluation at cutting performance and machinability process during the turning of AISI 4340 steel under different cooling conditions. The study analyses cutting operations during turning using dry, minimum quantity lubrication (MQL), and nano-MQL. As control parameters in the experiments, three different cooling types, cutting speed (100, 150, 200 m/min), and feed rate (0.1, 0.15, 0.20 mm/rev) levels were applied. The experiment results present that the optimal output values are found as Vb=0.15 mm, Ra=0.81µm, 88.1 dB for sound intensity, and I=4.18 A for current. Moreover, variance analysis (ANOVA) was performed to determine the effects of input parameters on response values. Under dry, MQL, and nano-MQL processing conditions, parameters affecting tool wear, surface roughness, current by the motor shaft, and sound level were examined in detail, along with the chip morphology. The responses obtained were optimized according to the Taguchi S/N method. As a result of optimization, it was concluded that the optimum values for cutting conditions (A3B1C1) were nano-MQL cooling and V=100 m/min, f=0.1 mm/rev cutting. Last but not least, it was observed that there was a 13% improvement in tool wear, 7% in current, 9% in surface roughness, and 8% in sound intensity compared to the standard conditions. In conclusion, it was determined that nano-MQL and the lowest level of cutting and feed rate values provided the optimum results.

This paper presents a comprehensive evaluation of metal foam employment within polymer electrolyte fuel cells (PEFCs) and compares it with conventional serpentine channels from both experiment viewpoints and computational fluid dynamics simulation. The experiments are designed to study the effects of material, area density, compression ratio, and final thickness of metal foam. Additionally, the influence of housing plate material and relative humidity (RH) is also tested for the first time. The results reveal that at RH=75-100%, the best distributor design is nickel foam with a compression ratio of 70%, a final thickness of 0.5mm, and SS-304 housing plate, which delivers 3110 mA cm^-2 as limiting current density that is scarce in the literature. The PEFC with this foam distributor shows a 10% improvement in maximum power density and 45% in limiting current density compared to the serpentine channel case. While at RH=30%, the same foam flow field with a final thickness of 1mm is a superior option. The experiments also indicate that maximum power density increases by 23% as the compression ratio rises from 0 to 70%, while reducing final thickness from 1 to 0.5 mm causes a 19% enhancement in cell performance. Simulation results reveal that metal foam is more successful in evenly reactant distribution so that the average oxygen mass fraction at the cathode catalyst layer is increased by 38% in the metal foam case compared to the serpentine channel.

We communicate the theoretical results in the study of utilizing the quantum phenomena in optical current for quantum computation in the context of high precision voltage measurements. These results can be used around computation by quantum sampling and quantum communication as the basis for further research and physical implementations. We propose a Main Optical Setup (MOS) for such computation which allows to make a superstructure to implement specific computations and algorithms. To create MOS we used the nonlinear units (e.g., beta- barium borate crystal), arranged in series, powered with pulsed laser pump, and ended with the beam splitter to generate the output state of a number of entangled photon pairs. The computation is made by propagation of entanglement with beam splitters applied crossword and adjustable phase shifters that are tools for parameter steering. We show how to implement the series of cosine-based components on the example of two-component case. The results opens a broad area for future research in the area of building quantum optimizer using the quantum sampling methods and in the area of high precision temporal measurement of voltage, which is the important process for building high-fidelity devices.