Memristor has attracted a lot of interest due to its high processing speed, low power consumption and high integration ability, which is critical for electronic systems and memory-centric computing. However, the memristor programming circuit and strategy are still inflexible and complex, since the signal generator/collector and stimulate pulse must be carefully matched and designed based on memristor intrinsic characteristics without reconfigurable. Here, a simple and effective circuit only consists a parallel reference-resistor-and-NMOS is designed to program memristor with a more than 99% memristance precision. And the amplitude and width of stimulate pulse are fixed to ±4V and 5ms, respectively. In order to cope with the device variation, such as ±10% tolerance of transition voltage, an optimized programming strategy was proposed and demonstrated great robustness. Additionally, a set of reference resistors and NMOSs have been added to facilitate multi-level memristance operation without requiring any changes to the circuit structure. This program circuit was also employed to program memristor crossbar remains 99% precision. In the end, a memristor-based convolutional neural network which controlled by our optimized programming circuit was used for image recognition, and 89.36% accuracy can be achieved even under 15.8% memristance tolerance. This novel circuit demonstrates a simple and flexible strategy in memristor programming, providing a new way to control memristor crossbar for practical application.

In this work, an novel flow-electric field coupling configuration for enhanced Zn-Cd cementation was designed and utilized. A series of tests were conducted to explore the optimization of Zn-Cd cementation process and its mechanism.Firstly, the various characterisations of the cadmium sponge at different locations in the device were compared and it was concluded that the purity of the cadmium sponge was optimal from the anode surface. The generation and stripping of cadmium sponge was revealed for the first time by cross-sectional electron microscopy. The four stages of the apparent reaction in the system were analysed in relation to the pH, cadmium concentration and cadmium sponge flaking at each flow rate. It was proved that the separation of cadmium sponge mainly occurred in the third phase. Secondly, by comparing the morphology and specific surface area of cadmium sheep at different flow rates, the optimum flow field velocity was identified as 30 ml/s. Six flow field configurations were compared and preferred. The results demonstrate that the LCAH modulation results in a more sparse structure of the cadmium sponge, which is more easily exfoliated from the zinc anode surface by fluid impact. This was considered to be the most beneficial flow field configuration for improving the cadmium cementation rate and reducing the cost of the reaction. Further, the reaction steps of the system were analysed. The diffusion process under different flow field configurations was confirmed by calculations to follow first order kinetics. The diffusion coefficient of LACH proved to be the highest in the comparative tests and this result was also supported by the apparent experimental results.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

The link of fracture analysis of large ships is an essential part of the structural safety of ships. However, the finite element analysis of large structure according to the traditional method not only has high requirements on the computer, but also the influence of the mesh encryption at special locations makes further requirements on the accuracy of the ship. In this paper, based on the extended finite element method (XFEM) and the multi-point constraint method (MPC), the dynamic crack expansion process of the rectangular plate containing cracks under the multi-scale model is comparatively studied by using ABAQUS simulation software Finally, the applicability of the method is verified by applying the multi-scale model of ship nodes. The results show that the computational effort of the multi-scale model is significantly reduced with the same accuracy and allowable error, which proves the accuracy and efficiency of the method.

According to the Global Report on Internal Displacement (GRID, 2022), the number of displaced people worldwide at the end of 2021 was 59.1 million, with 53.2 million of them being the result of conflicts and violence, and 5.9 million caused by climate-related disasters. Furthermore, the In-ternational Organization for Migration (IOM) predicts that the climate crisis will be solely re-sponsible for one billion migrants by 2050. In this context, the research examines the issue of coastal multi-risk arising from a combination of heavy rainfall, river's overflow, and sea-level rise phenomena, analysing it through the disciplinary perspective of urban planning. Specifically, the study focuses on the need to upgrade the Local Urban Plan from a climate-proof perspective by defining a method aimed at updating the territory's cognitive framework through the preparation of a multi-risk map (which considers different time horizons), as well as the prescriptive apparatus of the Plan through the definition of a toolkit of site-specific design actions oriented towards urban adaptation. The proposed methodology is verified on the case study of Isola Sacra, Fiumicino (Italy), and it is intended to be applicable to other territorial contexts. The research aims to outline guidelines for updating urban planning tools from a climate-proof perspective to promote long-term resilient urban development in risk-prone areas.

Purpose: Emotional voice conveys important social cues that demand listeners’ attention and timely processing. This event-related potential study investigated the feasibility of a multi-feature oddball paradigm to examine adult listeners’ neural responses to detecting emotional prosody changes in non-repeating naturally spoken words. Method: Thirty-three adult listeners completed the experiment by passively listening to the words in neutral and three alternating emotions while watching a silent movie. Previous research documented pre-attentive change-detection electrophysiological responses (e.g., MMN, P3a) to emotions carried by fixed syllables or words. Given that the MMN and P3a have also been shown to reflect extraction of abstract regularities over repetitive acoustic patterns, the current study employed a multi-feature oddball paradigm to compare listeners’ MMN and P3a to emotional prosody change from neutral to angry, happy, and sad emotions delivered with hundreds of non-repeating words in a single recording session. Results: Both MMN and P3a were successfully elicited by the emotional prosodic change over the varying linguistic context. Angry prosody elicited the strongest MMN compared to happy and sad prosodies. Happy prosody elicited the strongest P3a in the centro-frontal electrodes, and angry prosody elicited the smallest P3a. Conclusions: The results demonstrated that listeners were able to extract the acoustic patterns for each emotional prosody category over constantly changing spoken words. The findings confirm the feasibility of the multi-feature oddball paradigm in investigating emotional speech processing beyond simple acoustic change detection, which may potentially be applied to pediatric and clinical populations.

Background: The first few minutes after birth are the most dangerous for the survival of an infant. Babies in neonatal intensive care units are either under heated or overheated, and hypothermic infants remain hypothermic or develop a fever. As a result, special attention must be paid to monitoring and maintaining the time of recovery from hypothermia states. Despite numerous studies, only a few have examined the transition from neonatal hypothermia and associated risk factors in depth. Method: A retrospective observational study was conducted to track axillary temperatures taken at the time of neonatal intensive care unit admission, which were then tracked every 30 minutes until the newborn's temperature stabilized. All hypothermic neonates admitted to the neonatal intensive care unit between January 2018 and December 2020 was included in the study. Temperature data were available at birth and within the first three hours of admission for 391 eligible hypothermic neonates. The effect of factors on the transition rate in different states of hypothermia was estimated using a multi-state Markov model. Result: The likelihood of progressing from mild to severe hypothermia was 5%, while the likelihood of progressing to normal was 34%. The average time spent in a severe hypothermia state was 48, 35, and 24 minutes for three different levels of birth weight, and 53, 41, and 31 minutes for low, moderate, and normal Apgar scores, respectively. Furthermore, the mean sojourn time in a severe hypothermia state was 48, 39, and 31 minutes for three different levels of high, normal, and low pulse rate, respectively. Conclusion: For hypothermic survivors within the first three hours of life, very low birth weight, low Apgar, and high pulse rate had the strongest association with hypothermia and took the longest time to improve/recover. As a result, there is an urgent need to train all levels of staff dealing with maintaining the time of recovery from neonatal hypothermia.

In this note we describe a new approach to the option pricing problem by introducing the notion of the safe (and acceptable) for the writer price of an option, in contrast to the fair price used in the Black-Scholes model. Our starting point is that the option pricing problem is closely related with the hedging problem by practical techniques. Recalling that the Black - Scholes model does not give us the price of the option but the initial value of a replicating portfolio we observe easily that has a serious disadvantage because assumes the building of this replicating portfolio continuously in time and this is a disadvantage of any model that assumes such a construction. Here we study the problem from the practical point of view concerning mainly the over the counter market. This approach is not affected by the number of the underlying assets and is particularly useful for incomplete markets. In the usual Black-Scholes or binomial or some other approaches one assumes that one can invest or borrow at the same risk free rate $r>0$ which is not true in general. Even if this is the case one can immediately observes that this risk free rate is not a universal constant but is different among different people or institutions. So, the fair price of an option is not so much fair! Moreover, the two sides are not, in general, equivalent against the risk therefore the notion of a fair price has no meaning at all. We also define a variant of the usual binomial model, by estimating safe upward and downward rates $u,d$, trying to give a cheaper safe or acceptable price for the option.

Short-term changes in shallow bathymetry affect the coastal zone and therefore their monitoring is an essential task in coastal planning projects. This study provides a novel approach for monitoring shallow bathymetry change based on drone multispectral imagery. Particularly we apply a shallow water inversion algorithm on two composite multispectral datasets being acquired five months apart in a small Mediterranean sandy embayment (Chania, Greece). Initially, we perform radiometric corrections using proprietary software and following we combine the bands from standard and multispectral cameras resulting in a six-band composite image suitable for applying the shallow water inversion algorithm. Bathymetry inversion results showed good correlation and low errors (< 0.3m) with sonar measurements collected with an uncrewed surface vehicle (USV). Bathymetry maps and true-color orthomosaics assist in identifying morphobathymetric features representing crescentic bars with rip channel systems. The temporal bathymetry and true-color data reveal important erosional and depositional patterns, which were developed under the impact of winter storms. Furthermore, bathymetric profiles show that the crescentic bar appears to migrate across and along-shore over the 5-months period. Drone-based multispectral imagery proves to be an important and cost-effective tool for shallow seafloor mapping and monitoring when it is combined with shallow water analytical models.

Marketing is the manner of how to make our sales the best in the market, our prices the most accessible, our clients satisfactory, and thus our brand is the largest distributed. This needs sophisticated and advanced understanding of the total network related. Indeed, marketing data may be seen in different forms such as qualitative and quantitative. However, in the literature, it is easily noticed that large bibliography may be collected about qualitative studies, against few studies on the quantitative point of view. This is a major drawback that makes the marketing science still focusing on the design, although the market is strongly depending on quantities such as money and time. Indeed, marketing data may be a time series such as brand sales per specified periods, brand related-prices over specified periods, market shares, ..., etc. The purpose of the present work is to investigate some marketing models based on time series due to brands. We will precisely study the effect of the time scale on the persistence of brands sales in the market and on the forecasting of such a persistence according to the characteristics of the brand and the related market competition or competitors. Our study is acted on a sample of Saudi brands during the period November 22, 2017 to December 30, 2021.

The incidence and prevalence of food allergy (FA) are increasing. While several studies have established the safety and efficacy of early introduction of single allergens in infants for the prevention of FA, the exact dose, frequency, and number of allergens that can be safely introduced to infants particularly in those at high or low risk of atopy are still unclear. This 1-year study evaluated the safety of early introduction of single foods (milk, egg, or peanut), vs. two foods (milk/egg, egg/peanut, milk/peanut), vs. multiple foods (milk/egg/peanut/cashew/almond/shrimp/walnut/wheat/fish/soy at low, medium, or high doses) vs no early introduction in infants between 4-6 months of age. At the end of the study, they were evaluated for plasma biomarkers associated with food reactivity with standardized blood tests. Two to four years after the start of the study, participants were evaluated by standardized food challenges. The serving sizes for the single, double, and low dose mixtures were 300 mg total protein per day. The serving sizes for the medium and high dose mixture was 900 mg and 3000 mg total protein, respectively. Equal parts of each protein were used for double or mixture foods. All infants were breastfed until at least 6 months of age. Results demonstrate that infants at either high or low risk for atopy were able to tolerate early introduction of multiple allergenic foods with no increases in any safety issues, including eczema, FA, or food protein induced enterocolitis. The mixtures of foods at either low, medium, or high doses demonstrated trends for improvement in food challenge reactivity and plasma biomarkers compared to single and double food introductions. The results of this study suggest that early introduction of foods, particularly simultaneous mixtures of many allergenic foods is efficacious for preventing FA and can occur safely.

Often, engineers with machining experience often judge machining state and tool life according to chips’ features. Engineers' experience is digitized in this study. During the cutting process, the cutting tool coming in contact with the workpiece produces a shear zone, which causes plastic deformation and shear slip. The chips closest to the shear zone can directly show the state of the tool and workpiece when the material is SKD61. This study used chip color, vibration, and current signal integration for prediction of machining state and cutting tool life. When the cutting tool wears increased, the chip surface color changed in the following way: purpleè purple blueè blue ècyan, or even green and yellow. When the cutting tool was in the accelerating wear phase, the color change was particularly obvious. The Back-Propagation Levenberg–Marquardt (BP-LM) predictive methodology was used to compare the predictive ability of voltage, vibration signal, and chip color. The Mean Absolute Percentage Error (MAPE) for the voltage signal was 12.28%, for the vibration signal it was 11.38%, and for the chip color combined with multi-sensor characteristics it was 7.85%. The MAPE of the chip color was the smallest. Using the General Regression Neural Network (GRNN) methodology, the MAPE for the voltage signal was 10.74%, for the vibration signal 7.96%, and for the chip color combined with multi-sensor characteristics was 6.59%. The MAPE of the chip color was the smallest. Obviously, the chip color combined with multi-sensor signals provided better predictive results than the vibration signal or voltage signal alone. There is currently no research on the usefulness of monitoring chip color for tool life prediction.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

Autofocus is an essential part of the SAR imaging process. Multi-subaperture autofocus algorithm is a commonly used autofocus algorithm for processing SAR stripmap mode data. The multi-subaperture autofocus algorithm has two main steps, the first is to estimate the phase error gradient within the subaperture, the second is to splice the phase error gradient, that is, to remove the shift amount between the estimated adjacent subapertures’ error gradients. Previous gradient-splicing algorithms assume that the estimation of subaperture error is accurate, but when the estimation of subaperture phase error gradients is not accurate enough, these algorithm performance will be degraded. A new phase error gradient splicing algorithm is proposed in this paper. It roughly estimates the shift amount first, and then finely estimates the shift amount based on the minimum-entropy criterion, which can improve the robustness of splicing especially when the estimation of the phase error gradients of the subaperture is not accurate enough. To speed up the algorithm, a variable-step-size search method is used. Simulation and experimental results show that the algorithm has enough accuracy and still has good performance when other splicing algorithms doesn’t perform well.

Evolutionary convergence provides natural opportunities to investigate how, when, and why novel traits evolve. Many convergent traits are complex, highlighting the importance of explicitly considering convergence at different levels of biological organization, or ‘multi‐level convergent evolution’. To investigate multi‐level convergent evolution, we propose a holistic and hierarchical framework that emphasizes breaking down traits into several functional modules. We begin by identifying long‐standing questions on the origins of complexity and the diverse evolutionary processes underlying phenotypic convergence to discuss how they can be addressed by examining convergent systems. We argue that bioluminescence, a complex trait that evolved dozens of times through either novel mechanisms or conserved toolkits, is particularly well suited for these studies. We present an updated estimate of at least 94 independent origins of bioluminescence across the tree of life, which we calculated by reviewing and summarizing all estimates of independent origins. Then, we use our framework to review the biology, chemistry, and evolution of bioluminescence, and for each biological level identify questions that arise from our systematic review. We focus on luminous organisms that use the shared luciferin substrates coelenterazine or vargulin to produce light because these organisms convergently evolved bioluminescent proteins that use the same luciferins to produce bioluminescence. Evolutionary convergence does not necessarily extend across biological levels, as exemplified by cases of conservation and disparity in biological functions, organs, cells, and molecules associated with bioluminescence systems. Investigating differences across bioluminescent organisms will address fundamental questions on predictability and contingency in convergent evolution. Lastly, we highlight unexplored areas of bioluminescence research and advances in sequencing and chemical techniques useful for developing bioluminescence as a model system for studying multi‐level convergent evolution.

This investigation explores a novel path-planning and optimization strategy for multiple cooperative robotic agents, applied in a fully observable and dynamically changing obstacle field. Current dynamic path planning strategies employ static algorithms operating over incremental time-steps. We propose a cooperative multi-agent (CMA) based algorithm, based on natural flocking of animals, using vector operations. It is preferred over more common graph search algorithms like A* as it can be easily applied for dynamic environments. CMA algorithm executes obstacle avoidance using static potential fields around obstacles, that scale based on relative motion. Optimization strategies including interpolation and Bezier curves are applied to the algorithm. To validate effectiveness, CMA algorithm is compared with A* using static obstacles due to lack of equivalent algorithms for dynamic environments. CMA performed comparably to A* with difference ranging from -0.2% to 1.3%. CMA algorithm is applied experimentally to achieve comparable performance, with an error range of -0.5% to 5.2%. These errors are attributed to the limitations of the Kinect V1 sensor used for obstacle detection. The algorithm was finally implemented in a 3D simulated space, indicating that it is possible to apply with drones. This algorithm shows promise for application in warehouse and inventory automation, especially when the workspace is observable.

Understanding the detailed timing of crop phenology and their variability enhances grain yield and quality by providing precise scheduling of irrigation, fertilization, and crop protection mechanisms. Advances in information and communication technology (ICT) provide a unique opportunity to develop agriculture-related tools that enhance wall-to-wall upscaling of data outputs from point-location data to wide-area spatial scales. Because of the heterogeneity of the worldwide agro-ecological zones where crops are cultivated, it is unproductive to perform plant phenology research without providing means to upscale results to landscape-level while safeguarding field-scale relevance. This paper presents an advanced, reproducible, and open-source software for plant phenology prediction and mapping (PPMaP) that inputs data obtained from multi-location field experiments to derive models for any crop variety. This information can then be applied consecutively at a localized grid within a spatial framework to produce plant phenology predictions at the landscape level. This software supports the development of process-oriented and temperature-driven plant phenology models by intuitively and interactively leading the user through a step-by-step progression to the production of spatial maps for any region of interest. Maize (Zea mays L.) was used to demonstrate the robustness, versatility, and high computing efficiency of the resulting modeling outputs of the PPMaP. The framework is implemented in R, providing a flexible and easy‐to‐use GUI interface. Since this allows appropriate scaling to the larger spatial domain, the software can effectively be used to determine the spatially explicit length of growing period (LGP) of any variety.

Recent research has enabled the integration of traditional Volt-VAr Control (VVC) resources, such as capacitors banks and transformer tap changers, with Distributed Energy Resources (DERs), such as photo-voltaic sources and energy storage, in order to achieve various Volt-VAr Optimization (VVO) targets, such as Conservation Voltage Reduction (CVR), minimizing VAr flow at the transformer, minimizing grid losses, minimizing asset operations and more. When more than one target function can be optimized, the question of multi-objective optimization is raised. In this work, we propose a general formulation of the multi-objective Volt-VAr optimization problem. We consider the applicability of various multi-optimization techniques and discuss the operational interpretation of these solutions. We demonstrate the methods using simulation on a test feeder.

Biological gels (bio-gels) are hydrated polymer networks that serve diverse biological functions, which often lead to intentional or unintentional exposure to particulate matter. In this work, we derive a microscopically motivated framework that enables the investigation of penetration mechanisms into bio-gels. We distinguish between two types of mechanisms: spontaneous (unforced) penetration and forced penetration. Using experimental data available in literature, we exploit the proposed model to characterize and compare between the micro-structures of respiratory, intestinal, and cervicovaginal mucus and two types of biofilms. Next, we investigate the forced penetration process of spherical and ellipsoidal particles into a locally quadrilateral network. The proposed framework can be used to improve and complement the analysis of experimental findings in vitro, ex vivo, and in vivo. Additionally, the insights from this work pave the way towards enhanced designs of nano-medicines and allow to assess risk factors related to the nano-pollutants exposure.

The thermal lubrication of an entangled polymeric liquid in wall-driven shear flows between parallel plates is investigated by using a multiscale hybrid method coupling molecular dynamics and the hydrodynamics (i.e., the synchronized molecular dynamics method). The temperature of the polymeric liquid rapidly increases due to viscous heating once the drive force exceeds a certain threshold value. The rheological properties of the polymeric liquid drastically change at around the critical drive force. In the weak viscous-heating regime, the conformation of polymer chains is dominated by the local shear flow so that the anisotropy of the bond orientation tensor grows as the drive force increases. However, in the large viscous-heating regime, the conformation dynamics is dominated by the thermal agitation of polymer chains so that the bond orientation tensor recovers more uniform and random structures as the drive force increases, even though the local shear flows are further enhanced. Remarkably, these counter-intuitive transitional behaviors give an interesting re-entrant transition in the stress--optical relation, where a linear formalism in the stress--optical relation approximately holds even though each of the macroscopic quantities behaves nonlinearly. The robustness of the linear stress--optical relation is also confirmed in the spatiotemporal evolution at the hydrodynamic level.

Digital Elevation Models (DEMs) are widely used in geographic and environmental studies. In the current work, the fusion of multi-source DEMs is investigated to improve the overall accuracy of public domain DEMs. Multi-scale decomposition is an important analytical method in data fusion. Three multi-scale decomposition methods – the wavelet transform (WT), bidimensional empirical mode decomposition (BEMD) and nonlinear adaptive multi-scale decomposition (N-AMD) - are applied to the 1-arc-second Shuttle Radar Topography Mission Global digital elevation model (SRTM-1 DEM) and the Advanced Land Observing Satellite World 3D – 30 m digital surface model (AW3D30 DSM) in China. Of these, the WT and BEMD are popular image fusion methods. A new approach for DEM fusion is developed using N-AMD (which is originally invented to remove the cycle from sunspots). Subsequently, a window-based rule is proposed for the fusion of corresponding frequency components obtained by these methods. Quantitative results show that N-AMD is more suitable for multi-scale fusion of multi-source DEMs, taking the ice cloud and land elevation satellite (ICESat) global land surface altimetry data as a reference. The vertical accuracy of the fused DEM shows significant improvements of 29.6% and 19.3% in a mountainous region and 27.4% and 15.5% in a low-relief region, compared to the SRTM-1 and AW3D30 respectively. Furthermore, a slope position-based linear regression method is developed to calibrate the fused DEM for different slope position classes, by investigating the distribution of the fused DEM error with topography. The results indicate that the accuracy of the DEM calibrated by this method is improved by 16% and 13.6%, compared to the fused DEM in the mountainous region and low-relief region respectively, proving that it is a practical and simple means of further increasing the accuracy of the fused DEM.

Multi-task Gaussian processes (MTGPs) are a powerful approach for modeling structured dependencies among multiple tasks. Researchers on MTGPs have contributed to enhance this approach in various ways. Current MTGP methods, however, cannot model nonlinear task correlations in a general way. In this paper we address this problem. We focus on spectral mixture (SM) based kernels and propose an enhancement of this type of kernels, called multi-task generalized convolution spectral mixture (MT-GCSM) kernel. The MT-GCSM kernel can model nonlinear task correlations and mixtures dependency, including time and phase delay, not only between different tasks but also within a task at the spectral mixture level. Each task in MT-GCSM has its own generalized convolution spectral mixture kernel (GCSM) with a different number of convolution structures and all spectral mixtures from different tasks are dependent. Furthermore, the proposed kernel uses inner and outer full cross convolution between base spectral mixtures, so that the base spectral mixtures in the tasks are not necessarily aligned. Extensive experiments on synthetic and real-life datasets illustrate the difference between MT-GCSM and other kernels as well as the practical effectiveness of MT-GCSM.

An adaptive operation strategy for on-demand control of DMFC system is proposed as an alternative method to enhance the voltage stability. Based on a single-cell DMFC stack, a newly simplified semi-empirical model is developed from the uniform-designed experimental results to describe the I-V relationship. Integrated with this model, the multi-objective optimization method is utilized to develop an adaptive operation strategy. Although the voltage instability is frequently encountered in unoptimized operations, the voltage deviation is successfully decreased to a required level by adaptive operations with operational adjustments. Moreover, the adaptive operations are also found to be able to extend the range of operating current density or to decrease the voltage deviation according to ones requirements. Numerical simulations are implemented to investigate the underlying mechanisms of the proposed adaptive operation strategy, and experimental adaptive operations are also performed on another DMFC system to validate the adaptive operation strategy. Preliminary experimental study shows a rapid response of DMFC system to the operational adjustment, which further validates the effectiveness and feasibility of the adaptive operation strategy in practical applications. The proposed strategy contributes to a guideline for the better control of output voltage from operating DMFC systems.

This research proposes a framework to assist wind energy developers to select the optimum deployment site of a wind farm by considering the Round 3 zones in the UK. The framework includes optimisation techniques, decision-making methods and experts’ input in order to help stakeholders with investment decisions. Techno-economic, Life Cycle Costs (LCC) and physical aspects for each location are considered along with experts’ opinions to provide deeper insight into the decision making process. A process on the criteria selections is also presented and seven conflicting criteria are being considered in TOPSIS methods in order to suggest the optimum location that was produced by the NSGAII algorithm. Seagreen Alpha was the most probable solution, followed by Moray Firth Eastern Development Area 1, which demonstrates by example the effectiveness of the newly introduced framework that is also transferable and generic. The outcomes are expected to help stakeholders and decision makers to make more informed and cost-effective decisions under uncertainty when investing in offshore wind energy in the UK.

The development of printing technologies has enabled the realization of electric circuit fabrication on flexible substrate. However, the current technique remains restricted to single-layer patterning. In this paper, we demonstrate a fully solution-processable patterning approach for multi-layer circuits using a combined method of laser sintering and ablation. Selective laser sintering of silver (Ag) nanoparticle-based ink is applied to make conductive patterns on a heat-sensitive substrate and insulating layer. The laser beam path and irradiation fluence are controlled to create circuit patterns for flexible electronics. Microvia drilling using femtosecond laser through the polyvinylphenol-film insulating layer by laser ablation, as well as sequential coating of Ag ink and laser sintering, achieves an interlayer interconnection between multi-layer circuits. The dimension of microvia is determined by a sophisticated adjustment of laser focal position and intensity. Based on these methods, the flexible electronic circuit with chip-size-package light-emitting diodes was successfully fabricated and demonstrated with functional operations.

In this paper, we tackle air quality forecasting by using machine learning approaches to predict the hourly concentration of air pollutants (e.g., Ozone, PM_2.5 and Sulfur Dioxide). Machine learning, as one of the most popular techniques, is able to efficiently train a model on big data by using large-scale optimization algorithms. Although there exists some works applying machine learning to air quality prediction, most of the prior studies are restricted to small scale data and simply train standard regression models (linear or non-linear) to predict the hourly air pollution concentration. In this work, we propose refined models to predict the hourly air pollution concentration based on meteorological data of previous days by formulating the prediction of 24 hours as a multi-task learning problem. It enables us to select a good model with different regularization techniques. We propose a useful regularization by enforcing the prediction models of consecutive hours to be close to each other, and compare with several typical regularizations for multi-task learning including standard Frobenius norm regularization, nuclear norm regularization, ℓ_2,1 norm regularization. Our experiments show the proposed formulations and regularization achieve better performance than existing standard regression models and existing regularizations.

Multi-step ahead streamflow forecasting is of practical interest for the operation of hydropower reservoirs. We provide generalized results on the error evolution in multi-step ahead forecasting by conducting several large-scale experiments based on simulations. We also present a multiple-case study using monthly time series of streamflow. Our findings suggest that some forecasting methods are more useful than others. However, the errors computed at each time step of a forecast horizon within a specific case study strongly depend on the case examined and can be either small or large, regardless of the forecasting method used and the time step of interest.

Remote sensing has considerable potential to contribute to the identification and reconstruction of lost hydrological systems and networks. Remote sensing-based reconstructions of palaeo-river networks have commonly employed single or limited time-span imagery, which limits their capacity to identify features in complex and varied landscape contexts. This paper presents a seasonal multi-temporal approach to the detection of palaeo-rivers over large areas based on long-term vegetation dynamics and spectral decomposition techniques. The use of multi-temporal data has allowed the overcoming of seasonal cultivation patterns and long-term visibility issues related to crop selection, large-scale irrigation and land use patterns. The application of this approach on the Sutlej-Yamuna interfluve (northwest India), a core area for the Bronze Age Indus Civilisation, has enabled the reconstruction of an unsuspectedly complex palaeo-river network comprising more than 8000 kms of palaeo-channels. It has also enabled the definition of the morphology of these relict courses, which provides insights into the environmental conditions in which they operated. These new data will contribute to a better understanding of the settlement distribution and environmental settings in which this, often considered riverine, civilisation operated.

This article considers the concepts of sustainability and sustainable development in relation to disaster risk reduction and climate change adaptation. We conceptualize sustainability from a social systemic perspective, that is, from a perspective that encompasses the multiple functionalities of a social system and their interrelationships in particular environmental contexts. The systems perspective is applied in our consideration and analysis of disaster risk reduction (DRR), climate change adaptation (CCA), and sustainable development (SD). Section 1 introduces briefly sustainability and sustainable development, followed by a brief presentation of the theory of complex social systems (Section 2). The theory conceptualizes interdependent subsystems, their multiple functionalities, and the agential and systemic responses to internal and external stressors on a social system. Section 3 considers disaster risk reduction (DRR) and climate change adaptation (CCA), emerging in response to one or more systemic stressors. It illustrates these with disaster risk reduction in the cases of food and chemical security regulation in the EU. CCA is illustrated by initiatives and developments on the island of Gotland, Sweden and in the Gothenburg Metropolitan area, which go beyond a limited CCA perspective, taking into account long-term sustainability issues. Section 4 discusses the limitations of DRR and CCA, not only their technical limitations but economic, socio-cultural, and political limitations, as informed from a sustainability perspective. It is argued that DRRs are only partial subsystems and must be considered and assessed in the context of a more encompassing systemic perspective. Part of the discussion is focused on the distinction between sustainable and non-sustainable DRRs and CCAs. Section 5 presents a few concluding remarks about the importance of a systemic perspective in analyzing DRR and CCA as well as other similar subsystems in terms of sustainable development.

This paper proposes a new approach for multi-focus images fusion based on Region Mosaicing on Contrast Pyramids (REMCP). A density-based region growing method is developed to construct a focused region mask for multi-focus images. The segmented focused region mask is decomposed into a mask pyramid, which is then used for supervised region mosaicking on a contrast pyramid. In this way, the focus measurement and the continuity of focused regions are incorporated and the pixel level pyramid fusion is improved at the region level. Objective and subjective experiments show that the proposed REMCP is more robust to noise than compared algorithms and can fully preserves the focus information of the multi-focus images meanwhile reducing distortions of the fused images.

In this paper, the technical aspects of a multi-lidar instrument, the long-range WindScanner system, will be presented accompanied by an overview of the results from several field campaigns. The long-range WindScanner system consists of three spatially separated coherent Doppler scanning lidars and a remote master computer that coordinates them. The lidars were carefully engineered to perform arbitrary and time controlled scanning trajectories. Their wireless coordination via the master computer allows achieving and maintaining lidars’ synchronization within ten milliseconds. As a whole, the long-range WindScanner system can measure an entire wind field by emitting and directing three laser beams to intersect, and then by moving the beam intersection over the points of interest. The long-range WindScanner system was developed to tackle the need for high-quality observations of wind fields from scales of modern wind turbine and wind farms. It has been in operation since 2013.

This paper proposes an optimization method for the scheduling of a multi-energy virtual power plant supply-demand balance in the power market environment of Jiangxi Province. The objective of this method is to enhance the operational efficiency of the power grid, reduce energy costs, and facilitate economical and efficient energy distribution in the power market. The method comprehensively considers the characteristics and uncertainties of renewable energy sources such as solar and wind energy, and incorporates advanced multi-objective optimization algorithms. Additionally, real-time market price feedback is integrated to achieve accurate allocation of power supply and demand. Through a case study of a multi-energy virtual power plant in Jiangxi Province, this paper examines the optimal combination model for various energy sources within VPP, and analyzes the impact of different market environments on supply-demand balance. The results demonstrate that the proposed scheduling optimization method significantly improves economic benefits while ensuring grid stability. Compared with traditional power supply models, it reduces average electricity costs by 15% and increases renewable energy utilization efficiency by 20%.

This study utilized a multi-stage constant current (MSCC) charge protocol to identify the optimal current pattern (OCP) for effectively charging lithium-ion batteries (LiBs) using a Dandelion optimizer (DO). A Thevenin equivalent circuit model (ECM) was implemented to simulate an actual LiB with the ECM parameters estimated from offline time response data obtained through a hybrid pulse power characterization (HPPC) test. For the first time, DO was applied to me-taheuristic optimization algorithms (MOAs) to determine the OCP within the MSCC protocol. A composite objective function that incorporates both charging time and charging temperature was constructed to facilitate the use of DO in obtaining the OCP. To verify the performance of the proposed method, various algorithms, including the constant current-constant voltage (CC-CV) technique, formula method (FM), particle swarm optimization (PSO), war strategy op-timization (WSO), jellyfish search algorithm (JSA), grey wolf optimization (GWO), beluga whale optimization (BWO), levy flight distribution algorithm (LFDA), and African gorilla troops op-timizer (AGTO), were introduced. Based on the OCP extracted from simulations using these MOAs for the specified ECM model, a charging experiment was conducted on the Panasonic NCR18650PF LiB to evaluated the charging performance in terms of charging time, temperature, and efficiency. The results demonstrate that the proposed DO technique offers superior charging performance compared to other charging methods.

In recent years, demand has been increasing for target detection and tracking from aerial imagery via drones using onboard powered sensors and devices. We propose a very effective method for this application based on a deep learning framework. A state-of-art embedded hardware system empowers small flying robots to carry out the real-time onboard computation necessary for object tracking. Two types of embedded modules were developed: one is designed using a Jetson TX or AGX Xavier, and the other is based on an Intel Neural Compute Stick. These are suitable for real-time onboard computing power on small flying drones with limited space. A comparative analysis of current state-of-art deep-learning-based multi-object detection algorithms was carried out utilizing the designated GPU-based embedded computing modules to obtain detailed metric data about frame rates as well as the computation power. We also introduce an effective target tracking approach for moving objects. The algorithm for tracking moving objects is based on the extension of simple online and real-time tracking. It was developed by integrating a deep-learning-based association metric approach (Deep SORT), which uses a hypothesis tracking methodology with Kalman filtering and a deep-learning-based association metric. In addition, a guidance system that tracks the target position using a GPU-based algorithm is introduced. Finally, we demonstrate the effectiveness of the proposed algorithms by real-time experiments with a small multi-rotor drone.

Water networks are critical infrastructure components, ensuring the continuous supply of high-quality drinking water to consumers. To secure such water supply, regular maintenance, including the replacement of deteriorating pipelines, is essential. In this study, a methodology has been developed for determining optimal pipeline replacement solutions in water supply systems at water utilities with limited data availability. Hydraulic analysis has been conducted on the segment of 25 km of the water supply network using the free software EPANET. Applying water network optimization, eight pipeline replacement projects according to 13 pre-defined criteria have been identified and evaluated. The paper outlines the methods for evaluating the criteria, including defining specific quantitative limits. The Analytical Hierarchical Process (AHP) method was used in the paper to determine the weights of the criteria. The reason for applying this method refers to problems that involve a set of criteria with a mixed structure, including both quantitative and qualitative aspects. Also, the paper describes the steps of the multi-criteria optimization method VIKOR, used to select the optimal project. This paper, considered as case studie, describes a method, i.e. application of a new principles and an innovative way to solve a problem for developing countries.

Fiber-optic Mach-Zehnder interferometers are widely used in research areas such as telecommunications, spectroscopy, and quantum information. These optical structures are known to be affected by phase fluctuations that are usually modeled as multiparametric noise.This multidimensional noise must be stabilized or compensated for to enable fiber-optic Mach-Zehnder architectures for practical applications. In this work, we study the effectiveness of a modified Perturb-and-Observe (P&amp;O) algorithm to control multidimensional phase noise in fiber-based multi-arm Mach-Zehnder interferometers. We demonstrate the feasibility of stabilizing multidimensional phase noise by numerical simulations using a simple feedback control scheme and analyze the algorithm’s performance for systems up to dimension 8x8. We achieved minimal steady-state errors that guarantee high optical visibility in complex optical systems with N×N matrices (with N=[2,3,4,5,6,7,8]).

Green Infrastructure (GI) is increasingly prioritised in landscape policy and planning, due to its potential to benefit ecosystems and enhance wildlife conservation. However, due to the uneven distribution of protected areas (PAs) and the fragmentation of habitats more generally, multi-level policy strategies are needed to create an integrated GI network bridging national, regional and local scales. To help address this challenge, we present proposals to integrate GI elements for the province of Almeria, southeast Spain. We delimit and define key GI elements, and apply GIS-based connectivity tools to generate ecological corridors connecting the province’s 35 PAs. Currently, the PAs are threatened by the advance of intensive greenhouse agriculture and tourism-related urban growth of the municipalities to which they belong. Common patterns in the location of the most suitable areas for the development of GI can be identified. New GI networks would be located along the coast, specifically in the western part of the study area. They would also occupy the valleys of the main rivers of the province. Around 50% of the area occupied by the proposed corridors would be located in places of medium and high suitability for the movement of species between core areas.

We developed and applied a new calibration method to make the measurement more accurate with our multi-color ellipsometric mapping tool from cheap parts. Ellipsometry is an optical technique that measures the relative change in polarization state of the measurement beam induced by reflection from or transmission though a sample. During the conventional ellipsometric measurement, the data collection is relatively slower and measures one spot at a time, so mapping needs long time compared with our new optical mapping equipment made by an ordinary color LED monitor and a polarization sensitive camera. The angle-of-incidence and the incident polarization state is varied point-by-point so a special optical calibration method is needed. Three SiO2 samples with different thicknesses were used to determine point-by-point the angle-of-incidence and rho corrections. After the calibration, another SiO2 sample was measured and analyzed using the calibrated corrections and this sample further was independently measured using a conventional spectroscopic ellipsometer. The difference between the two measured thickness maps is less than 1 nm. Our optical mapping tool from cheap parts is faster and covers wider area samples in relative to the conventional ellipsometers and these correction enhancements further signify its performance.

Pile foundations are widely employed in engineering to bolster structures and efficiently transmit loads to the underlying soil or rock. However, in karst terrains, the occurrence of multi-layered stone projections or caves can drastically affect the bearing capacity and stability of these pile foundations. In order to study the influencing factors of vertical bearing capacity of pile founda-tion in multi-layer karst cave environment, the bearing capacity test of pile foundation was carried out at the construction site. The results show that with the increase of external load eccentricity, the bearing capacity of pile foundation decreases obviously. Subsequently, we developed a finite element model for pile foundations in a double-layered karst area using the commercial general finite element software ANSYS. This model facilitated our analysis of the bearing capacity of concrete pile foundations under progressively increasing loads, accounting for variations in rock height, eccentricity, and elastic modulus. The findings reveal the following: (1) Under consistent external loading, the maximum displacement of pile foundations increases with eccentricity. (2) As concrete strength rises, the maximum displacement gradually decreases, while the corresponding peak stress remains approximately constant. (3) The height of karst caves significantly impacts the bearing capacity of pile foundations. Therefore, during construction, it is crucial to minimize or avoid traversing areas with high karst caves. In engineering applications involving multi-layered karst landforms, it is essential to assess the bearing capacity of pile foundations beforehand, paying particular attention to the effects of karst cave height, pile eccentricity, and concrete strength on the bearing capacity. This will enable the optimization of the design scheme, avoidance of high karst cave areas, and ensure the safety and stability of the structure.

Due to the inherent limitations of a single viewpoint, reconstructing 3D human meshes 1 from a single image has long been a challenging task. While deep learning networks enable us to 2 approximate the shape of unseen sides, capturing the texture details of the non-visible side remains 3 difficult with just one image. Traditional methods utilize Generative Adversarial Networks (GANs) 4 to predict the normal maps of the non-visible side, thereby inferring detailed textures and wrinkles 5 on the model’s surface. However, we have identified challenges with existing normal prediction 6 networks when dealing with complex scenes, such as a lack of focus on local features and insufficient 7 modeling of spatial relationships.To address these challenges, we introduce EMAR—Enhanced 8 Multi-scale Attention-driven Single Image 3D Human Reconstruction. This approach incorporates 9 a novel Enhanced Multi-Scale Attention (EMSA) mechanism, which excels at capturing intricate 10 features and global relationships in complex scenes. EMSA surpasses traditional single-scale attention 11 mechanisms by adaptively adjusting the weights between features, enabling the network to more 12 effectively leverage information across various scales.Furthermore, we have improved the feature 13 fusion method to better integrate representations from different scales. This enhanced feature fusion 14 allows the network to more comprehensively understand both fine details and global structures 15 within the image. Finally, we have designed a hybrid loss function tailored to the introduced attention 16 mechanism and feature fusion method, optimizing the network’s training process and enhancing the 17 quality of reconstruction results.Our network demonstrates significant improvements in performance 18 for 3D human model reconstruction. Experimental results show that our method exhibits greater 19 robustness to challenging poses compared to traditional single-scale approaches.

This study presents the development and evaluation of a Multi-Task Long Short-Term Memory (LSTM) model with an Attention Mechanism designed to predict students' academic performance. The model concurrently addresses two tasks: predicting overall performance (total score) as a regression task and categorizing performance levels (remarks) as a classification task. By processing both tasks simultaneously, the model optimizes computational efficiency and resource use. The dataset includes detailed student performance records across various metrics such as Continuous Assessment, Practical Skills, Demeanor, Presentation Quality, Attendance, and Participation. The model's performance was evaluated using comprehensive metrics. For the regression task, it achieved a Mean Absolute Error (MAE) of 0.0249, Mean Squared Error (MSE) of 0.0012, and Root Mean Squared Error (RMSE) of 0.0346. For the classification task, it attained perfect scores with an accuracy, precision, recall, and F1 score of 1.0. These results highlight the model's high accuracy and robustness in predicting both continuous and categorical outcomes. The Attention Mechanism enhances the model's capabilities by identifying and focusing on the most relevant features. This study demonstrates the effectiveness of the Multi-Task LSTM with Attention Mechanism in educational data analysis, offering a reliable tool for predicting student performance and potential broader applications in similar multi-task learning contexts. Future work will explore further enhancements and wider applications to improve predictive accuracy and efficiency.

With the rapid advance in quantum computing, quantum security is now an indispensable property for any cryptographic system. In this paper, we study how to prove the security of a complex cryptographic system in the quantum random oracle model. We first give a variant of Zhandry’s compressed quantum random oracle (CStO), called compressed quantum random oracle with adaptive special points (CStOs). Then, we extend the on-line extraction technique of Don et al (EUROCRYPT’22) from CStO to CStOs. We also extend the random experiment technique of Liu and Zhandry (CRYPTO’19) for extracting the CStO query that witnesses the future adversarial output. With these preparations, a systematic security proof in the quantum random oracle model can start with a random CStO experiment (that extracts the witness for the future adversarial output) and then convert this game to one involving CStOs. Next, the on-line extraction technique for CStOs can be applied to extract the witness for any on-line commitment. With this strategy, we give a security proof of our recent compact multi-signature framework that is converted from any weakly secure linear ID scheme. We also prove the quantum security of our recent lattice realization of this linear ID scheme, by iteratively applying the weakly collapsing protocol technique of Liu and Zhandry (CRYPTO 2019). Combining these two results, we obtain the first quantum security proof for a compact multi-signature.

In central area of Liaoning province, the thermal performance of rural building envelopes are mostly non-standardized in Northern China, resulting in a significant heat loss. In this study, The objective was to propose some low-cost and energy-efficient solutions. Through a field of inves-tigations, heating energy consumption was saved by 20% and increased construction costs was less than 8000 RMB, which was acceptable for rural residents. In order to achieve this target, NSGA-II algorithm was integrated with Rhino+Grasshopper and EnergyPlus simulation kernel to establish a thermal performance optimization model for heat transfer of the rural building envelopes. Among the above Pareto optimal solutions, the recommended thickness of insulation layer for the room floors, ceilings, and external walls were 70mm, 50mm, and 40mm respectively. Furthermore, try to reduce the window to wall ratio as much as possible. Finally, based on the lower total cost, three technical solutions that rural residents could select according to their specific needs have been put forward.

Non-polio enteroviruses (NPEVs), namely coxsackieviruses (CV), echoviruses (E), enteroviruses (EV), and rhinoviruses (RV), are responsible for a wide variety of illnesses. Some infections can progress to life-threatening complications in children or immunocompromised patients. To date, no treatments have been approved. Several molecules have been evaluated through clinical trials without success. To overcome these failures, the multi-target directed ligand (MTDL) strategy can be applied to tackle enterovirus infections. This work analyzes clinical trials to highlight the best candidates and develops filters to apply to a selection for MTDL synthesis. We explicitly stated the methods used to answer the question: Which solution can fight NPEVs effectively? We note the originality and relevance of this proposal in relation to the state of the art in the enterovirus-inhibitors field. Several combinations are possible to broaden the antiviral spectrum and potency. We discuss data related to the virus and data related to each LEAD compound identified. Overall, this study proposes a perspective on different strategies to overcome issues identified in clinical trials and evaluate the “MTDL” potential to improve the efficiency of drugs synergistically, broaden the targeted, and reduce the adverse effects and drug design cost as well as limit the opportunity of drug-resistant viruses.

The enhanced multi-objective symbolic discretization for time series (eMODiTS) method employs a flexible discretization scheme using different value cuts for each non-equal time interval, which requires a computational cost for evaluating each objective function. Therefore, surrogate models were implemented to minimize this disadvantage. Nevertheless, each solution found by eMODiTS is a different-sized vector, so the surrogate model must be able to handle data sets under this characteristic. Consequently, this work's contribution lies in analyzing the surrogate models' implementation on the time series discretization, where each potential scheme is a real-number different-sized vector. For this reason, the surrogate model proposed was k-nearest Neighbors for regression with Dynamic Time Warping as a distance measure. Results suggest our proposal finds a suitable approximation to the final eMODiTS solutions with a functions evaluation reduction rate between 15% and 95%. However, according to Pareto front performance measures, the proposal Pareto front is competitive compared to the eMODiTS Pareto front, reaching an average Generational Distance (GD) between 0.0447 and 0.0536. Moreover, the average Hypervolume Ratio (HVR) ranges between 0.334 and 0.3891. Finally, our proposal compared against SAX-based methods presents a similar behavior regarding classification tasks and statistical tests.

This work investigated the influence of current density, plating solution flow rate, and nozzle outlet-cathode distance on the properties of Ni-diamond composite coatings. A multi-physics field simulation is employed to analyze the interplay between current density, plating solution flow rate, and nozzle outlet-cathode distance on the flow field and electric field distribution. Additionally, particle tracing simulations were incorporated into the model to evaluate the incorporation efficiency of diamond particles during composite electrodeposition. Experimental validation of the findings shows a significant increase in the diamond particle content of the coating. This combined approach provides valuable insights for optimizing the jet electrodeposition process for Ni-diamond composite coatings with superior properties.

As screen sizes are becoming larger and larger, which are beyond human’s physical limitation for direct touching interaction, remote controls are inevitable. However, as techniques applied so far, inertial gyroscopes are susceptible to position inaccuracies, and gesture recognition is limited by cameras’ focus depth and viewing angle. Grating antenna light trapping technology will be an ideal candidate providing the ghost point problem for multipoint inputs can be solved. Therefore, we propose a differential amplitude modulation scheme for grating antenna based multi beam optical touch, which can recognize different incidence points. Where, the amplitude of the incident beams was coded with different pulse width at first. Then, after been trapped by the grating antenna and been transferred into currents by the lined detector arrays, the incident points of the individual beams were recognized and differentiated. The scheme was successfully verified on an 18-inch screen, where two-point optical touch with position accuracy error under 3mm and response time less than 7ms under modulation frequency of 10kHz on both incident beams are obtained. This work paves a practical way for remote multi-point touch, which can make digital mouse in consistent to the users pointing direction obeying natural three-point one ling aiming rule instantaneously.

Nonlinear loads, a crucial component of power systems grids, pose a challenge due to harmonics injection. Our research tackles this issue with a novel approach - a modified green plug / switched filter compensation scheme using fuzzy logic controllers. This innovative scheme, presented in the paper, utilizes dual action pulse width modulation to ensure switching functions from harmonic reduction and capacitive compensation for inrush nonlinear type AC loads.  The scheme's multi-loop regulations and online switching effectively handle dynamic type slow acting inrush, motorized and other rectifier type-nonlinear loads, enhancing power factor, power quality at source and load buses, and reducing total harmonic distortion at key source and sensitive nonlinear load buses. A simulation model in the MATLAB/SIMULINK software environment demonstrates the efficiency of the proposed FACTS technique. The results show that voltage, current, active power, reactive power, power factor regulation, and effective energy utilization are achievable with the designed FACTS-MFCC-SFC. The switched modulated AC green plug filter significantly improves power quality and enhances power factor in the case of inrush and nonlinear loads.

The increase in population and the challenges caused by it are always among the concerns of decision-makers and policymakers in large countries. One of the most serious concerns is in the field of energy consumption. Optimizing energy use is one of the most effective ways to manage limited resources and energy. Energy consumption in residential houses constitutes a significant percentage of the total energy consumption worldwide; therefore, current research focusing on mathematical models aims to provide a predictive multi-objective linear mathematical model for residential house consumption. For this purpose, the consumption of water, electricity, and gas for 80 residential houses, including 10 household appliances and equipment on a weekly basis, has been considered. The results showed that the mixed-integer multi-objective predictor model is able to optimize household consumption plans compared to the actual state of household energy consumption. Since the goals of household satisfaction and energy consumption costs in the model conflict with each other, the influence coefficient was calculated to demonstrate the simultaneous achievement of these goals. The optimal value achievable with the default model for the model's purposes is 69%.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

This study analyses the changes in land use in the Sado estuary (West-Central Portugal) based on a multitemporal analysis of cartographic data from the 19th century and remote sensing land use maps from the 21st century, updated by field work. A GIS plotting of land-use evolution is summarized in a quantitative table. The comparison shows the changes in land use, with increasing occupation by human economic activities, including extensive agriculture and forestry, as well as localized urbanization and industrialization. The main elements of the landscape impacted by anthropogenic uses were: i) hydrography - river dams affected the flow dynamics and sedimentary processes in the estuary; ii) vegetation – increasing agriculture and forestry reduced the areas of native vegetation, nowadays mostly occupied by vineyards, pine forests and cork oaks. iii) wetlands - tidal and alluvial plains are being occupied by rice cultivation, aquaculture, industries, and ports; iv) coastal dunes – new developments are occupying large areas of Holocene coastal dunes; v) natural environment – mining and dredging affected some habitats and biodiversity. This analysis is intended to help the territorial organization of present and future economic activities, as well as to reduce environmental and social problems, promoting long-term sustainability of this rapidly evolving region.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

Visual Sensor Networks (VSNs) have been the focus of numerous studies, emphasizing the quality of the information they generate. The primary goal of these networks is to capture data from an area, extract the pertinent information from the visual scene, and facilitate communication. However, the presence of objects in the study area can impacted the network's efficiency, linking the quality of acquired data directly to the positioning of the cameras. Strategically positioning multiple cameras in a potentially complex area, while ensuring effective communication between nodes, presents a challenging issue in VSNs applications. This paper introduces a specific method to enhance the deployment of visual sensors in indoor environments. The research addresses the theme of multi-objective optimization of VSN deployment, integrating various criteria: maximizing overall visual coverage, maximizing the observation of zones of interest, maximizing observation redundancy of zones of interest and ensuring communication connectivity for data transfers. To tackle this problem, we simulate the observed environment incorporating cameras, obstacles, and considering zones of interest. Camera positioning is performed while considering visual constraints and the scene's characteristics. The quality of positioning is evaluated based on the defined objective functions. Initially, a comparative study is conducted with a state-of-the-art approach, integrating the first three objective functions. Subsequently, we incorporate the fourth objective function to ensure data transfers. The proposed method demonstrates efficient camera network deployments in indoor areas, considering global coverage and observation redundancy. In contrast to the state-of-the-art, these results are achieved in areas with visual obstacles while ensuring communication connectivity between the different cameras.

In an agricultural system, finding suitable watering, pesticide, and soil content to provide the right nutrients for the right plant is a mystery so far. Plants cannot speak and cannot ask which food they require. These problems can be addressed by applying intelligent (fuzzy logic) controllers to IoT devices in order to enhance communication between crops, ground mobile robots, aerial robots, and the entire farm system. The application of fuzzy logic in agriculture is a promising technology that can be used to optimize crop yields and reduce water usage. It was developed based on language and the air properties in the agricultural fields were formulated. The entire system was simulated in the MATLAB/SIMULINK environment with Cisco Packet Tracer integration. The inputs for the system were soil moisture sensors, temperature sensors, humidity sensors, and outputs were pump flow, valve opening, water level, and moisture in sounding. The obtained results were the output of opening valve, moisture in sound, pump flow rate, outflows, water level, and ADH values, which are 10.00000013 rad/sec, 34.72%, 4.494%, 0.025 m^3/sec, 73.31 cm^3, and 750 values respectively. The outflow rate increase indicates that the water is released from the tanks, and the control signal fluctuates, indicating that the valve is opening.

The ratio between blade height and chord, named aspect ratio (AR), plays an important role in compressor aerodynamic design. Once selected, it influences stage performance, blade losses, and the stage stability margin. The choice of the design AR involves both aerodynamic and mechanical considerations, and a reasonable aim is frequently to achieve a desired operating range while maximizing efficiency. For a fixed set of aerodynamic and geometric parameters there will be an optimal choice in AR that achieves a maximum efficiency. However, for a state-of-the-art aero-engine design optimality means multi-objective optimality, that is reaching the highest possible efficiency for a number of operating points while achieving a sufficient stability margin. To this end, the influence of the AR on the performance of the first rotor row of a multistage multi-objective high-speed compressor design is analyzed. A careful setup of the high-speed aerodynamic design problem allows the effect of the AR to be isolated. Close to the optimal AR, only a modest efficiency variation is observed, but a considerable change in compressor stability margin (SM) is noted. Decreasing the AR allows for an increasing efficiency, but at the expense of a reduced surge margin. This allows the designer to trade efficiency for stability. Increasing the AR, however, is shown to reduce both surge margin and efficiency, hence a distinct optimality in stability is observed for the analyzed rotor blade row. In this work, the optimality in surge margin with respect to AR is observed whereas a close to optimal efficiency. The predicted range from AR=1.10 to AR=1.64, is only indicative, considering that the definition of a multi-objective optimality requires balancing efficiency and surge margin and that the choice of balancing these two criteria requires making a design choice along a pareto optimal front.

This article is devoted to overcoming the contradiction between the problem of maximizing the extraction of wind energy as the goal of optimizing wind turbines, and the use of traditional methods based on criteria for the aerodynamic quality of the blades. A modified technique is considered in which the optimization criterion is the directly extracted flow power. It is based on pulse theory methods that use specific power as an optimization criterion. A comparative analysis of the energy efficiency of different types of turbines is carried out, and the effects of blade inversion are considered. A method for calculating multi-rotor turbines based on the concept of uniform power distribution is presented. The compatibility of proprietary and traditional methods is considered by comparing the results of numerical experiments with calculated and experimental data from sources. Optimization computational algorithms generate data from numerical experiments and determine optimal parameter configurations for the turbines under consideration. It is shown that orthogonal Darrieus turbines in high-speed mode provide energy efficiency comparable to collinear turbines, and multi-rotor turbines with power uniformly distributed over the working section are not inferior in energy efficiency to basic turbines, with linear blade velocities halved.

The concept and policies of multiple early cancer detection (MCED) have gained significant attention from governments worldwide in recent years. In the era of burgeoning artificial intelligence (AI) technology, the integration of MCED with AI has become a prevailing trend, giving rise to a plethora of MCED AI products. However, due to the heterogeneity of both the detection targets and the AI technologies, the overall diversity of MCED AI products remains considerable. The types of detection targets encompass protein biomarkers, cell-free DNA, or combinations of these biomarkers. In the development of AI models, different model training approaches are employed, including datasets of case-control researches or real-world cancer screening datasets. Various validation techniques, such as cross-validation, location-wise validation, and time-wise validation are used. All of the factors show significant impacts on the predictive efficacy of MCED AIs. After the completion of AI model development, deploying the MCED AIs in clinical practice presents numerous challenges, including presenting the predictive reports, identifying the potential locations and types of tumor, and addressing cancer-related information such as clinical follow-up and treatment. This study reviews several mature MCED AI products currently available in the market, detecting their composing factors from serum biomarkers detection, MCED AIs training/validation, and the clinical application. The review illuminates the challenges encountered by existing MCED AI products across these stages, offering insights into the continued development and obstacles within the field of MCED AI.

In this study, we present a federated learning approach that combines a multi-branch network and the Oort client selection algorithm to improve the performance of federated learning systems. This method successfully addresses the significant issue of non-iid data, a challenge not adequately tackled by the commonly used MFedAvg method. Additionally, one of the key innovations of this research is the introduction of uniformity, a metric that quantifies the disparity in training time amongst participants in a federated learning setup. This novel concept not only aids in identifying stragglers but also provides valuable insights into assessing the fairness and efficiency of the system. Experimental results underscore the merits of the integrated multi-branch network with the Oort client selection algorithm and highlight the crucial role of uniformity in designing and evaluating federated learning systems.

In this computational study, we investigate the electronic properties of zigzag graphene nano-parallelograms (GNPs), which are parallelogram-shaped graphene nanoribbons of various widths and lengths, using thermally-assisted-occupation density functional theory (TAO-DFT). Our calculations reveal a monotonic decrease in the singlet-triplet energy gap as the GNP length increases. The GNPs possess singlet ground states for all the cases examined. With the increase of GNP length, the vertical ionization potential and fundamental gap decrease monotonically, while the vertical electron affinity increases monotonically. Besides, as the GNP length increases, the symmetrized von Neumann entropy increases monotonically, denoting an increase in the degree of multi-reference character associated with ground-state GNPs. The occupation numbers and real-space representation of active orbitals indicate that there is a transition from the nonradical nature of the shorter GNPs to the increasing polyradical nature of the longer GNPs. In addition, the edge/corner localization of active orbitals is found for the wider and longer GNPs.

An algorithm is proposed for discriminating the fatigue state of air traffic controllers based on ap-plying multispeech feature fusion using an FSVM to voice data, and for extracting eye-fatigue-state discrimination features based on PERCLOS eye data. For the speech algorithm and an eye-fatigue index, a new controller fatigue-state evaluation index based on the entropy weight method is proposed based on decision-level fusion of fatigue discrimination results for speech and the eyes. Experimental results show that the fatigue-state recognition accuracy rate was 84.81% for the fatigue state evaluation index, which was 3.36% and 1.86% higher than those for speech and eye assessments, respectively. The comprehensive fatigue evaluation index provides important reference values for controller scheduling and mental-state evaluations.

Deep networks-based hashing has gained significant popularity in recent years, particularly in the field of image retrieval. However, most existing methods only focus on extracting semantic information from the final layer, disregarding valuable structural information that contains important semantic details crucial for effective hash learning. To address this limitation and improve image retrieval accuracy, we propose a novel deep hashing method called Deep Supervised Hashing by Fusing Multiscale Deep Features (DSHFMDF). Our approach involves extracting multiscale features from multiple convolutional layers and fusing them to generate more robust representations for efficient image retrieval. Experimental results on CIFAR10 and NUS-WIDE datasets demonstrate that our method surpasses the performance of state-of-the-art hashing techniques.

The purpose of this article is to present a multi-criteria model designed to evaluate the potential of Sincelejo's cultural identity for tourism development. A descriptive quantitative methodology was used, which included a survey of 211 participants. A decision support method was applied, using the Weighted Additive Sum approach, following the multi-attribute method. Based on the information gathered, the elements of cultural identity shared by most of the criteria were identi-fied, highlighting the gastronomic, social, and cultural traditions and customs of the region, the results of which made it possible to design a composite indicator to evaluate the tourism potential of cultural identity in the area.

Multi-source image registration often suffered from great radiation and geometric differences. Specifically, gray scale and texture from similar landforms in different source images often show significantly different visual features. And these differences disturb the corresponding point extraction in the following image registration process. Considering that edges between heterogeneous images can provide homogeneous information and more consistent features can be extracted based on image edges, an edge consistency radiation-change insensitive feature transform (EC-RIFT) method is proposed in this paper. Firstly, the noise and texture interference are reduced by preprocessing according to the image characteristics. Secondly, image edges are extracted based on phase congruency, and an orthogonal Log-Gabor filter is performed to replace the global algorithm. Finally, the descriptors are built with logarithmic partition of the feature point neighborhood, which improves the robustness of descriptors. Comparative experiments on datasets containing multi-source remote sensing image pairs show that the proposed EC-RIFT method outperforms other registration methods in terms of precision and effectiveness.

: The radar multi target tracking (MTT) technique requires prior knowledge of a number of parameters about the sensor, the target and backgrounds. The Integrated Track Splitting (ITS) is a fully automatic track-while-scan (TWS) target tracking algorithm capable of extracting and tracking a target in a dense clutter environment using quality false track discrimination (FTD) methodology. The computational complexity in ITS algorithm is limited, compared to other algorithms they use statistical methods to discriminate between false and true tracks, such as multiple hypothesis tracking (MHT), mainly due to the FTD performed. The paper provides an analysis of tracking parameters that allows determining the limit of the possibility of successful target tracking. Extensive experiments have confirmed that the recursive determination of the probability of the existence of a track during tracking can confirm a true track and reject a false track. The clutter density, number of random occurred targets, targets load during the maneuver and the target detection probability were varied. The results of experiments, carried out via Monte Carlo simulations, shown over representative confirmed true tracks (CTT) diagrams, root mean square error position and normalized tracking efficiency parametric diagrams allow the user to select optimal multi-target tracking parameters for different scenarios and clutter densities.

Cumulative exposure to multiple early life stressors are expected to affect behavioral development causing increased susceptibility towards neuropsychiatric disorders. The present study was designed to mimic such conditions in rat model to study behavioral impairments during adolescence and adulthood. Female Wistar rats (n=32; 140-150 gm) were switched to low protein (LP; 8% protein) or Control (20% protein) diet, 15 days prior to conception and then diet regime was maintained throughout the experimental period. Pups born to Control and LP dams were intraperitoneally injected with deltamethrin (DLT-pyrethroid insecticide; 0.7mg/kg body weight; PND 1 to 7) or lipopolysaccharide (LPS-bacterial endotoxin; 0.3mg/kg body weight; PND 3 and 5) or DLT+LPS, on designated days forming 8 experimental groups (Control, LP, Control+LPS, LP+LPS, Control+DLT, LP+DLT, Control+DLT+LPS and LP+DLT+LPS). Neurobehavioral assessments were performed in F1 rats (1, 3, 6 months) by Open field, Elevated plus maze, Light and Dark box, and Rotarod tests. LP rats were found to be more susceptible to either singular or cumulative exposure as compared to their age matched control counterparts, showing significantly severe behavioural abnormalities, as hyperactivity, attention deficits, impulsiveness and low anxiety, the hallmark symptoms of neuropsychiatric disorders like schizophrenia and ADHD, suggesting thereby that early life multi-hit exposure may predispose individuals to developmental disorders.

In this paper, a new multi parameter iterative algorithm is proposed to address the PageRank problem based on the multi-splitting iteration method described by Gu et al . The proposed method in each iteration needs to solve two linear subsystems by splitting the coefficient matrix, therefore, we consider inner and outer iteration to find the approximate solutions of these linear subsystems. It can be shown that the iterative sequence generated by the multi parameter iterative algorithm finally converges to the PageRank vector when the parameters satisfy the certain conditions. Numerical experiments show that the proposed algorithm has better convergence and numerical stability than the existing algorithms.

Two monophyletic Daphnia species (Daphnia magna and D. similis) were exposed to a sub-lethal concentration of Pb (50 µg/L) for nine generations under two food regimes (usual and restricted) and analysed for acetylcholinesterase (AChE) activity, hatching delay and lifespan, and Net Reproductive Rate (R0) at subcellular, individual and population levels, respectively. At the sixth generation, Pb acclimated neonates were moved to a clean media for three more generations to check for recovery. D. magna showed no Pb effect on Net Reproductive Rate (R0). However, Pb stimulated reproduction, reduced lifespan and decreased AChE activity. Hatching delay and lifespan did not improve during the recovery process, indicating genetic adaptation. Food restriction reduced R0, lifespan, delayed hatching, and increased AChE activity; opposite outcomes were shown for D. similis. Full recovery shown by R0 suggests a physiological acclimation of D. similis. Under food restriction, the animals exhibited a reduction of R0 and lifespan, delayed hatching and increased AChE activity; however, with no Pb effect. The recovery process under food restriction showed that D. similis might not cope with Pb exposure, indicating failed recovery. Such outcomes indicate that a model species' sensitivity may not represent another's sensitivity.

Cerebrovascular and airway structures are tubular structures used for transporting blood and gases, respectively, providing essential support for the normal activities of the human body. Accurately segmenting these tubular structures is the basis of morphology research and patho-logical detection. Nevertheless, accurately segmenting these structures from images presents great challenges due to their complex morphological and topological characteristics. To address this challenge, this paper proposes a framework UARAI based on the U-Net multi-scale reverse at-tention network and sparse convolution network. The framework utilizes a multi-scale structure to effectively extract the global and deep detail features of vessels and airways. Further, it enhances the extraction ability of fine-edge features by a joint reverse attention module. In addition, the sparse convolution structure is introduced to improve the features' expression ability without increasing the model's complexity. Finally, the proposed training sample cropping strategy re-duces the influence of block boundaries on the accuracy of tubular structure segmentation. The experimental findings demonstrate that the UARAI-based metrics, namely Dice and IoU, achieve impressive scores of 90.31% and 82.33% for cerebrovascular segmentation and 93.34% and 87.51% for airway segmentation, respectively. Compared to commonly employed segmentation tech-niques, the proposed method exhibits remarkable accuracy and robustness in delineating tubular structures such as cerebrovascular and airway. These results hold significant promise in facilitating medical image analysis and clinical diagnosis, offering invaluable support to healthcare profes-sionals.

Distributed Manufacturing (DM) is becoming increasingly important in operations management due to its potential to support sustainability goals, reduce risks in global supply chains, and boost local economies. However, previous analyses of the advantages and disadvantages of DM have mainly focused on operations, overlooking additional benefits across the supply chain. For example, DM can enable local sourcing, better serve end-users, and tackle reverse supply chain challenges. While economies of scale are essential for reducing costs and improving productivity, highly centralised manufacturing can increase transportation costs, vulnerability, and supply chain disruptions, particularly during pandemics or other times of restricted transportation. To address these challenges, this study introduces a Multi-attribute Decision Support System (MADSS) and assessment process that considers impacts across the supply chain and guides stakeholders, academics, and decision-makers. The MADSS handles quantitative and qualitative information, missing data, and uncertainty, and a team of experts from academia and industry in New Zealand has developed the evaluation. The MADSS was used to analyse DM and traditional construction alternatives from economic, social, environmental, and resilience perspectives in New Zealand. The research contributes to a better understanding of the impacts of DM across the entire supply chain. Also, it proposes a flexible decision-making framework to engage with stakeholders and support decision-making in other industries and regions.

This paper applies a new artificial intelligence architecture, the Temporal Fusion Transformer (TFT), for the joint GDP forecasting of 25 OECD countries at different time horizons. This new attention-based architecture offers significant advantages over other deep learning methods. First, results are interpretable since the impact of each explanatory variable on each forecast can be calculated. Second, it allows to visualize persistent temporal patterns and to identify significant events and different regimes. Third, it provides quantile regressions and permits to train the model on multiple time series from different distributions. Results suggest that TFTs outperform regression models, especially in periods of turbulence such as the COVID-19 shock. Interesting economic interpretations are obtained depending on whether the country is domestic demand-led or export-led growth. In essence, TFT is revealed as a new tool that artificial intelligence provides to economists and policy makers, with enormous prospects for the future.

This paper describes methods for evaluating the thermal properties of textile materials, clothing composites, and clothing using an integrated measurement system that includes a hot plate, a multi-purpose differential conductometer, a thermal manikin, a temperature gradient measurement device, and a device for measuring the physiological parameters of the human body during the exact evaluation of garment thermal comfort. In practice, measurements were taken on four types of materials widely used in the production of conventional and protective clothing. The measurements were carried out using a hot plate and a multi-purpose differential conductometer, determining the thermal resistances of the material in its uncompressed form and a force that was ten times greater than that needed to determine its thickness. Using a hot plate and a multi-purpose differential conductometer, thermal resistances of textile materials were assessed at different levels of material compression. On hot plates, both conduction and convection had an impact on thermal resistance, but in multi-purpose differential conductometer, only conduction did. Moreover, the reduction of thermal resistance was observed while compressing textile materials.

Non-pneumatic tires have gained a lot of attention due to their advantages, including not having to worry about getting a flat tire. In this type of tire, metamaterial cells replace the pneumatic part of the tire. In general, metamaterials are formed by stacking cells together. These cells are obtained by various methods including topology optimization. Therefore, in this research, to achieve a metamaterial cell suitable for a non-pneumatic tire with the objective function of increasing compressive strength and bending fatigue life, optimization for three types of geometry including (1) square plane, (2) rectangular plane, and (3) entire circumference of tire and three types of material including polylactic acid (PLA), thermoplastic polyurethane (TPU) and void have been done. Optimization has been implemented by using MATLAB code in 2D mode. The cubic cell is obtained from extruding the optimized response of the square plane. From the optimized response of the rectangular plane, the cylindrical cell and from extruding the optimized response of the entire circumference of tire to the tire cross-section size, the main geometry of the tire has been calculated. Finally, to check the quality of 3D printing in producing cells and how they are connected, the optimal cell fabricated by the fused deposition modeling (FDM) method has been observed using a field-emission scanning electron microscopy (FE-SEM). The results show that in the optimization of the square plane, the sample with the minimum remaining weight constraint equal to 40% and in the optimization of the rectangular plane and the entire circumference of tire, the sample with the minimum remaining weight constraint equal to 60% was selected as the optimal sample. From checking the quality of 3D printing, it has been concluded that PLA and TPU materials are completely connected.

The glucose-insulin regulatory system and its glucose oscillations is a recurring theme in the literature because of its impact on human lives, mostly the ones affected by diabetes mellitus. Several approaches were proposed, from mathematical to data-based models, with the aim of modeling the glucose oscillation curve. Having such a curve, it is possible to predict, when injecting insulin in type 1 diabetes (T1D) individuals. However, the literature presents prediction horizons no longer than 6 hours, which could be a problem considering their sleeping time. This work presents Tesseratus, a model that adopts a multi-agent approach to combine machine learning and mathematical modeling to predict the glucose oscillation up to 8 hours. Tesseratus uses the pharmacokinetics of insulins and data collected from T1D individuals. Its outcome can support endocrinologists while prescripting daily treatment for T1D individuals, and provide personalized recommendations for such individuals, to keep their glucose concentration in the ideal range. Tesseratus brings pioneering results for prediction horizons of 8 hours for nighttime, in an experiment with seven real T1D individuals. It is our claim that Tesseratus will be a reference for classification of glucose prediction model, supporting the mitigation of short- and long-term complications in the T1D individuals.

Users on the social networking platform have the freedom to express themselves freely. Towards the same time, this has created a forum for disagreement and hate directed at someone, society, racism, sexual orientation, and so on. Identifying hate online is a challenging task. Researchers from all around the world have contributed major methods for detecting hate speech, but owing to the issue's complexity, there are still many unresolved issues. In this research, we offer a multi-model learning strategy for detecting hate speech on Twitter. We utilised the Kaggle TwitterHate dataset, which had 31962 tweets categorised as binary hate or non-hate, to evaluate our technique. The suggested method is tested using commonly used machine learning classifiers with multi-model technique. Using TF-IDF features, we acquired detection results of 96.29 %, precision of 96%, recall of 96%, and f1-score of 96%.

Graph neural networks (GNNs) build on the success of deep learning models by extending them for use in graph spaces. Transfer learning has proven extremely successful for traditional deep learning problems: resulting in faster training and improved performance. Despite the increasing interest in GNNs and their use cases, there is little research on their transferability. This research demonstrates that transfer learning is effective with GNNs, and describes how source tasks and the choice of GNN impact the ability to learn generalisable knowledge. We perform experiments using real-world and synthetic data within the contexts of node classification and graph classification. To this end, we also provide a general methodology for transfer learning experimentation and present a novel algorithm for generating synthetic graph classification tasks. We compare the performance of GCN, GraphSAGE and GIN across both the synthetic and real-world datasets. Our results demonstrate empirically that GNNs with inductive operations yield statistically significantly improved transfer. Further we show that similarity in community structure between source and target tasks support statistically significant improvements in transfer over and above the use of only the node attributes.

Salinity acts as a critical environmental filter on microbial communities in natural systems, negatively affecting microbial diversity. However, how salinity affects the community assembly remains unclear. This study used Wendeng multi-pond saltern as a model to evaluate the prokaryotic community composition and diversity and quantify the relative importance of ecological processes across salinity gradients. Results showed that low saline salterns (45-80 g/L) exhibited higher bacterial diversity than those in high saline salterns (175-265 g/L). The relative abundance of taxa assigned to Halanaerobiaceae, Haloferacaceae, Desulfohalobiaceae, Phormidiaceae, Rohodobacteraceae, and Nitrococcaceae was higher with increasing salinity. Salinity and pH were the primary environmental factors that directly or indirectly determined the composition and diversity of prokaryotic communities. Microbial co-occurrence network dynamics were more complex in the sediment than in water of salterns. An infer Community Assembly Mechanisms by Phylogenetic-bin-based null model analysis (iCAMP) showed that microbial community assembly in sediment and water differed. Our findings provide more information about microbial community structure and the importance of various ecological processes in controlling microbial community diversity and succession along salinity gradients in water and sediment environments.

This paper extends the concept of weighted graphs to matrix weighted graphs. The consensus algorithms dictate that all agents reach consensus when the weighted graph is connected. However, it is not always the case for matrix weighted graphs. The conditions leading to different types of consensus have been extensively analysed based on the properties of matrix-weighted Laplacians and graph theoretic methods. However, in practice, there is concern on how to pick matrix-weights to achieve some desired consensus, or how the change of elements in matrix weights affects the consensus algorithm. By selecting the elements in the matrix weights, different clusters may be possible. In this paper, we map the roles of the elements of the matrix weights in the systems consensus algorithm. We explore the choice of matrix weights to achieve different types of consensus and clustering. Our results are demonstrated on a network of three agents where each agent has three states.

Metaheuristic algorithms have been frequently using to tackle optimization problems, however such algorithms in the analysis of health-related data is not commonly used as developing metaheuristic algorithms that work well on health-related data is a difficult task due to complexity of the health data in particular genomics and epigenetics data. One of the important tasks in genomics is to predict genomic elements that are incorporating together to regulate a disease-related genes. Predicting such elements are important as they can be used to develop a personalized cure. In this study, we present for the first time, a multi-object simulated annealing algorithm to identify enhancer-promoter like interactions from Hi-C (chromosome conformation capture) data. These regulatory elements can potentially play vital roles as promoters and/or enhancers in appearance and exacerbation of the regulation of gene.s To evaluate the efficiency of the proposed method, we applied our proposed method and traditional methods on the Hi-C data from mice and compared together. Our results show that the interacting elements identified by our new method are more likely to be functional. The source code of the method is publicly available.

The devastating COVID-19 pandemic forced academia to go virtual. Educational institutions around the world have stressed online learning programs in the aftermath of the pandemic. However, because of insufficient access to ICT, a substantial number of students failed to harness the opportunity of online learning. This study explores the latent digital divide exhibited during the COVID-19 pandemic while online learning activities are emphasized among Bangladeshi students. It also investigates the digital divide exposure and the significant underlying drivers of the divide. A cross-sectional survey was employed to collect quantitative data mixed with open-ended questions to collect qualitative information from the student community. The findings revealed that despite the majority of students have physical access to ICT but only 32.5% of students could attend online classes seamlessly, 34.1% of the students reported the data prices as the critical barrier, and 39.8% of students identified the poor network infrastructure is the significant barrier for them to participate in online learning activities. Although most students possess physical access to the device and the Internet, they face the first-level digital divide due to the quality of access and maintaining subscriptions. Consequently, they fail to take advantage of physical access, resulting in the third-level digital divide (Utility Gap) and submerging them into a digital divide cycle. This paper aimed to explore the underlying issues of the digital divide among Bangladeshi students to assist relevant stakeholders (e.g., the Bangladesh government, Educational Institutions, Researchers) in providing the necessary insights and theoretical understanding to arrange adequate support for students to undertake conducive online learning activities.

The practical application of a multi-objective optimization strategy based on evolutionary algorithms was proposed to optimize the plastics thermoforming process. For that purpose, the various steps of the process were considered individually and the optimization strategy was applied to the determination of the final part thickness distribution with the aim of demonstrating the validity of the methodology proposed. The preliminary results obtained considering three different theoretical initial sheet shapes indicates clearly that the methodology proposed is valid, as it provides solutions with physical meaning and with a great potential to be applied in real practice.

The paper is focused on numerical modeling of multi-strand cable lines placed in free air. Modeling is carried out within the framework of the so-called multi-physics approach using commercial software. The paper describes in detail the steps undertaken to develop realistic, reliable numerical models of power engineering cables, taking into account their geometries and heat exchange conditions. The results might be of interest to the designers of multi-strand cable systems.

The use of different sources to energize a load is convenient in many applications, particularly those where two or more renewable energy sources are employed as: energy harvesting, hybrid vehicles, and off-grid systems. In these cases, a multi-input converter able to admit sources with different characteristics and, if necessary, select the output power of each source. Several topologies of multi-input converters have been proposed to this aim, however, most of them are based on multi-stage designs, which decreases efficiency and increases control complexity, particularly when more than two sources are used. In this work, a three-input step-up converter easy to control in open loop condition is analyzed. A designed procedure is described, and experimental results are presented for a 1 kW power converter. The implemented converter results in a higher voltage gain, less storage element keeping high efficiency compared to similar topologies. Using the procedure here proposed, this converter that was initially proposed for photovoltaic applications is enabled to be used in medium and high-power applications, for example when renewable energy sources are used.

The article contains the results of experimental studies for a multi-opening orifice with substitute constriction factor of β = 0.5 (m = 0.25), mounted in a DN50 hydraulic measuring flume. Flow measurements were taken for a progressing turbulent flow within Reynolds numbers (Re = 4700...19500). Based on experimental data, flow characteristics as well as discharge coefficient C characteristics were determined. Relative expanded uncertainty of determining a discharge coefficient C was estimated within the changes of volume flow qv from 0.35 dm3/s to 0.68 dm3/s. The value does not exceed 1.25% within the changes of Reynolds numbers 9800 ≤ Re ≤ 19500.

Insulation systems for the floor, roof and external walls play a prominent role in providing a thermal barrier for the building envelope. Design decisions made for the insulation material type and thickness can alleviate potential impacts on the embodied energy and improve the building thermal performance. This design problem is often addressed using a BIM-integrated optimisation approach. However, one major weakness lies in the current studies is that BIM is merely used as the source for design parameters input. This study proposes a BIM-based envelope insulation optimisation design framework using a common software Revit to find the trade-off between the total embodied energy of the insulation system and the thermal performance of the envelope by considering the material type and thickness. In addition, the framework also permits data visualisation in a BIM environment, and subsequent material library mapping together with instantiating the optimal insulation designs. The framework is tested on a case study based in Sydney, Australia. By analysing sample designs from the Pareto front, it is found that slight improvement in the thermal performance (1.3399 to 1.2112 GJ/m2) would cause the embodied energy to increase by more than 50 times.

Background: Extraintestinal pathogenic Escherichia coli (ExPEC) is the most common cause of urinary tract infections (UTIs). They are often multidrug-resistant (MDR), making them challenging to treat. Additionally, virulence mechanisms as biofilm formation are associated with persistent UTIs. Aims: To reveal a possible association between patients’ risk factors and UTIs caused by MDR or biofilm-forming ExPECs and characterize ExPECs causing asymptomatic bacteriuria, community- (CA), or hospital-acquired (HA) UTIs in hospitalized patients in Brazil. Methods: Bacterial DNA was extracted from the urine of 63 hospitalized patients and sequenced using short-read sequencing. Antibiotic susceptibility was evaluated using VITEK-2, and the biofilm-forming, adhesion, and invasion abilities were quantitatively assessed. Results: Antibiotic resistance rates were high, and the majority of UTIs were complicated CA-UTIs. Most MDR- and ESBL-producing E. coli isolates belonged to high-risk lineages and were associated with UTIs in patients with comorbidities and over 60 years of age. The mortality rate of patients infected with MDR-isolates was higher than of those infected with non-MDR isolates. Most isolates were biofilm-forming, but no association with patients’ risk factors was found. Conclusions: Complicated UTIs caused by MDR- and biofilm-forming bacteria are frequently found in hospitalized patients in Brazil suffering from a UTI and are associated with high-risk lineages.

Skin and proximity effects have a considerable impact on current distribution in multi-strand cable lines. Under unfavorable heat exchange conditions some strands may be subject to excessive overheating, what may lead to serious malfunctions or even fires of the installation. The paper proposes a new criterion for a quick choice of spatial configurations, for which the effect might be minimized. A comprehensive analysis of literature cases is provided, including the recommendations of the U.S. National Code and the Canadian standard.

In this paper, the effect of multi-rotational speeds super-gravity field on the grain refinement and tensile properties of as-cast H13 steel were investigated systematically. The experimental results revealed that the as-cast grains of H13 steel can be significantly refined in multi-rotational speeds supergravity field. In conventional supergravity field, with the decrease of rotational radius, the secondary dendrite average spacing (SDAS) and the austenite grain average size (AGAS) increase, and the maximum values of SDAS and AGAS are 90 µm and 55 µm, respectively. while in multi-speeds supergravity fields, at the range of increasing rotational speeds, SDAS and AGAS decrease as the rotational radius decreases. In three-rotational speeds supergravity field, the maximum values of SDAS and AGAS are 80 µm and 50 µm. In five-rotational speeds supergravity field, the maximum values of SDAS and AGAS are reduced to 58 µm and 34 µm. Accordingly, both the tensile strength and the plasticity are enhanced with the increasing the number of rotational speeds in supergravity field, especially for the inner position of supergravity sample. The ultimate tensile strengths at outer, middle, and inner positions of H13 steel solidified in conventional supergravity field are 1445 MPa, 1378 MPa, and 1023 MPa, corresponding elongations of 2%, 1.5%, and 0.5%, while in the five-rotational speeds supergravity field, they are 1408 MPa, 1443 MPa, and 1453 MPa, corresponding elongations of 1.8%, 3.9%, and 2.2%. The mechanism for the grain refinement is that multi-speeds super-gravity can reduce the critical nucleation work of austenite, and the tangential force produced by changing the rotational speeds breaks dendrites at the solidification front, refining solidification structure.

Ability of quantitative structure – property / activity relationships (QSPRs/QSARs) to serve for epistemological processes in natural sciences is discussed. Some weirdness of QSPR/QSAR state-of-art are listed. There are some contradictions in the research results in this area. Sometimes, these should be classified as paradoxes or weirdness. These points often are ignored. Here these are listed and briefly commented. In addition, hypothesises on the future evolution of the QSPR/QSAR theory and practice are suggested.

There exist numerous high-dimensional problems in the real world which cannot be solved through the common traditional methods. The metaheuristic algorithms have been developed as successful techniques for solving a variety of complex and difficult optimization problems. Notwithstanding their advantages, these algorithms may turn out to have weak points such as lower population diversity and lower convergence rate when facing complex high-dimensional problems. An appropriate approach to solve such problems is to apply multi-agent systems along with the metaheuristic algorithms. The present paper proposes a new approach based on the multi-agent systems and the concept of agent, which is named Multi-Agent Metaheuristic (MAMH) method. In the proposed approach, several basic and powerful metaheuristic algorithms, including Genetic Algorithm (GA), Particle Swarm Optimization (PSO), Artificial Bee Colony (ABC), Firefly Algorithm (FA), Bat Algorithm (BA), Flower Pollination Algorithm (FPA), Gray Wolf Optimizer (GWO), Whale Optimization Algorithm (WOA), Crow Search Algorithm (CSA), Farmland Fertility Algorithm (FFA), are considered as separate agents each of which sought to achieve its own goals while competing and cooperating with others to achieve the common goals. In overall, the proposed method was tested on 32 complex benchmark functions, the results of which indicated effectiveness and powerfulness of the proposed method for solving the high-dimensional optimization problems. In addition, in this paper, the binary version of the proposed approach, called Binary MAMH (BMAMH), was executed on the spam email dataset. According to the results, the proposed method exhibited a higher precision in detection of the spam emails compared to other metaheuristic algorithms and methods.

Directional modulation (DM), as an emerging promising physical layer security (PLS) technique at the transmitter side with the help of an antenna array, has developed rapidly over decades. In this study, a DM technique using a polarization sensitive array (PSA) to produce the modulation with different polarization states (PSs) at different directions is investigated. A PSA, as a vector sensor, can be employed for more effective DM for an additional degree of freedom (DOF) provided in the polarization domain. The polarization information can be exploited to transmit different data streams simultaneously at the same directions, same frequency, but with different PSs in the desired directions to increase the channel capacity, and with random PSs off the desired directions to enhance PLS. The proposed method has the capability of concurrently projecting independent signals into different specified spatial directions while simultaneously distorting signal constellation in all other directions. The symbol error rate (SER), secrecy rate, and the robustness of the proposed DM scheme are analyzed. Design examples for single- and multi-beam DM systems are also presented. Simulations corroborate that 1) the proposed method is more effective for PLS; 2) the proposed DM scheme is more power-efficient than the traditional artificial noise aided DM schemes; and 3) the channel capacity is significantly improved compared with conventional scalar antenna arrays.

To improve the effect of multi-point stretch forming of sheet metal, it is proposed in this paper to replace fixed ball head with swinging ball head. According to the multi-point dies with different arrangements, this research establishes the finite element models of the following stretch forming, i.e. fixed ball heads with conventional arrangement, swinging ball heads with conventional arrangement, swinging ball heads with declining staggered arrangement, and swinging ball heads with parallel staggered arrangement and then numerical simulation is performed. The simulation results show that by replacing fixed ball head with swinging ball head, the surface indentation of the formed part was effectively suppressed, the stress and tension strain distribution of the formed part was improved and the forming quality was improved; that the thickness of the elastic pad was reduced, the springback was reduced and the forming accuracy was improved; and that when the ball head was applied to multi-point die with staggered arrangement, better forming result was achieved, where the best forming result was achieved in combining the swinging ball heads with the multi-point die with parallel staggered arrangement. The forming experiments were carried out, and the experimental results were consistent with the trend of numerical simulation results, which verified the correctness of the numerical simulation.

Yogyakarta City is one of the big city which is located in Java Island, Indonesia. Yogyakarta City, including study area (Pleret Sub District), are very prone to earthquake hazards, because close to several active earthquake sources. For example, Sunda Megathrust which often generates a big earthquake which can affect the study area. The Sunda Megathrust extends from north to south and west to east along the Sumatra and Java Islands. Furthermore, an active normal fault called as Opak Fault pass through right in the middle of Study area and divides the study area into east and west zone. Recently, after the devastating earthquake in 2006, the population of the study area increases significantly. As a result, the housing demand is also increasing. However, due to the absence of earthquake building code in the study area, locals tend to build improper new houses. Furthermore, in some part of the mountainous area in the study area, there are some building found in unstable slopes area. Due to this condition, the multi-hazard and risk study needs to be done in Pleret. The increasing of population and improper houses in Pleret Sub-District can lead to amplify the impact. Thus, the main objective of this study is to assess the multi-hazards and risk of earthquake and other related secondary hazards such as ground amplification, liquefaction, and coseismic landslide. The method mainly utilised the geographic information system, remote sensing and was fit up by the outcrop study. The results show that the middle part of the study area has a complex geological structure. It was indicated by a lot of unchartered faults was found in the outcrops. Furthermore, the relatively prone areas to earthquake can be determined. In term of the coseismic landslide, the prone area to the coseismic landslide is located in the east part of the study area in the middle slope of Baturagung Escarpment. The highly potential area of liquefaction is dominated in the central part of the study area. In term of building collapsed probability, the result shows that the safest house based on statistical analysis is the residential house with the building attribute of wood structure, roof cast material, distance more than 15 km from the earthquake source, and located above the Nglanggran Formation. Finally, the multi-hazard and risk analysis show that the middle part of the study area is more vulnerable than the other part of Pleret Sub-District.

Clustered regularly interspaced short palindromic repeats/associated protein 9 nuclease (CRISPR/Cas9) technology guided by a single-guide RNA (sgRNA) has recently opened a new avenue for antiviral therapy. A unique capability of the CRISPR/Cas9 system is multiple genome engineering. However, there are few applications in insect viruses by a single Cas9 enzyme targeting two or more sgRNA at different genomic sites for simultaneous production of multiple DNA breaks. To address the need for multi-gene editing and sustained delivery of multiplex CRISPR/Cas9-based genome engineering tools, we developed a one-vector (pSL1180-Cas9-U6-sgRNA) system to express multiple sgRNA and Cas9 protein to excise Bombyx mori nucleopolyhedrovirus (BmNPV) in insect cells. Here, ie-1, gp64, lef-11, and dnapol genes were screened and identified as multiple sgRNA editing sites according to the BmNPV system infection and DNA replication mechanism. Furthermore, we constructed a multiplex editing vector sgMultiple to efficiently regulate multiplex gene editing steps and inhibit BmNPV replication after viral infection. This is the first report that describes the application of multiplex CRISPR/Cas9 system inhibiting insect virus replication. This multiplex system can significant enable the potential of CRISPR/Cas9-based multiplex genome engineering in transgenic silkworms.

The paper deals with the modelization and optimization of an integrated multi-component energy system. On-off operation and presence-absence of components must be described by means of binary decision variables, besides equality and inequality constraints; furthermore, the synthesis and the operation of the energy system should be optimized at the same time. In this paper a hierarchical optimization strategy is used, adopting a genetic algorithm in the higher optimization level, to choose the main binary decision variables, whilst a MILP algorithm is used in the lower level, to choose the optimal operation of the system and to supply the merit function to the genetic algorithm. The method is then applied to a distributed generation system, which has to be designed for a set of users located in the center of a small town in the North-East of Italy. The results show the advantage of distributed cogeneration, when the optimal synthesis and operation of the whole system are adopted, and significant reduction in the computing time by using the proposed two-level optimization procedure.

In the process of sustainable development in the future, human society faces problems such as severe population load, economic transition, and lack of educational measures. One of the root causes of these problems is the shortage of innovative talents. Therefore, how to cultivate learners with multi-disciplinary integration and innovation ability is the key point that should be paid attention to in promoting the concept of quality education and coping with the future sustainable development process. This paper uses questionnaire survey method and literature analysis method to analyze the development of many educational institutions with STEAM concept as the core in China since 2017. It is found that the existing STEAM educational institutions generally have the following problems: the lack of team composition、difficulty in independent research and development、single course content and insufficient validation of course effectiveness. In order to more effectively promote the sustainable development of China's future course, STEAM education institutions should focus on strengthening the following development strategy: gradient team building, continuous independent research and development, cutting-edge projects curriculum transformation mechanism and multi-angle course effectiveness verification.

Measuring farms sustainable innovativeness is a big challenge for both practitioners and academics. The need of sustainable innovativeness assessment in the agricultural business is reasoned in the article. Unfortunately, the features of the farms sustainable innovativeness measurement have not yet been investigated, and any objective methodology for innovativeness assessment is not presented as well. The objective of this article is to find possibility of use some methodology for measuring farm sustainable innovativeness, which would allow ranking farms by this aspect. The article demonstrates the need for multi-criteria method of innovativeness measurement and substantiates the complex proportional assessment method (Copras) as the most appropriate for solution of indicated problem. The model for use of offered method is presented and the practical application of the model is submitted. The final result refuted the opinion that farm innovation depends only on the possibilities to invest funds in a certain area. Indeed, staff creativity and the position of the management regarding certain areas of business make an essential contribution to the sustainable innovativeness level in the agricultural organizations.

Unmanned aerial vehicles (UAV) provide an unprecedented capacity to monitor the development and dynamics of tree growth and structure through time. It is generally thought that the pruning of tree crops encourages new growth, has a positive effect on fruiting, makes fruit-picking easier, and may increase yield, as it increases light interception and tree crown surface area. To establish the response of pruning in an orchard of lychee trees, an assessment of changes in tree structure, i.e. tree crown perimeter, width, height, area and Plant Projective Cover (PPC), was undertaken using multi-spectral UAV imagery collected before and after a pruning event. While tree crown perimeter, width and area could be derived directly from the delineated tree crowns, height was estimated from a produced canopy height model and PPC was most accurately predicted based on the NIR band. Pre- and post-pruning results showed significant differences in all measured tree structural parameters, including an average decrease in tree crown perimeter of 1.94 m, tree crown width of 0.57 m, tree crown height of 0.62 m, tree crown area of 3.5 m², and PPC of 14.8%. In order to provide guidance on data collection protocols for orchard management, the impact of flying height variations was also examined, offering some insight into the influence of scale and the scalability of this UAV based approach for larger orchards. The different flying heights (i.e. 30, 50 and 70 m) produced similar measurements of tree crown width and PPC, while tree crown perimeter, area and height measurements decreased with increasing flying height. Overall, these results illustrate that routine collection of multi-spectral UAV imagery can provide a means of assessing pruning effects on changes in tree structure in commercial orchards, and highlight the importance of collecting imagery with consistent flight configurations, as varying flying heights may cause changes to tree structural measurements.

In this study, we examine the relationship of bank level lending and borrowing decisions and the risk preferences on the dynamics of the interbank lending We develop an agent-based model that incorporates individual bank decisions using the temporal difference reinforcement learning algorithm with empirical data of 6600 S. banks. The model can successfully replicate the key characteristics of interbank lending and borrowing relationships documented in the recent literatur A key finding of this study is that risk preferences at individual bank level can lead to unique interbank market structures which are suggestive of the capacity that the market responds to surprising

In this study, functionalized-MWCNTs with 3-aminopropyltriethoxysilane (APTES) loaded titania nanoparticles (MWCNTs-APTES-TiO₂) were prepared to investigate their physicochemical properties and photocatalytic activity for methyl orange (MO) degradation. The TiO₂ nanoparticles, functionalized-MNCNT and composite powders were characterized by XRD, raman, and TEM. The results obtained proved that titania (TiO₂) nanoparticles was successfully loaded on APTES-MWCNTs. The best photocatalytic degradation of methyl orange solution under UV light irradiation was recorded over MWCNTs-APTES-TiO₂ (1:2), with 87% after 180 min. Kinetic analysis indicated that photocatalytic degradation of MO solution by MWCNTs-APTES-TiO₂ obeyed second-order kinetic model (R² > 0.95), supported by half-life equations and graph. The presence of carbon nanotubes accelerated the degradation of methyl orange due to inhibition of electron-hole recombination, the formation of additional hydroxyl radicals and functional groups of the latter had an inhibitory effect on the degradation of methyl orange. This study shows that the MWCNTs-APTES-TiO₂ nanocomposites exhibit promising photocatalytic degradation against methyl orange.

Alcohol abuse can result in detrimental multisystem effects. Chronic alcohol abuse is known to be associated with pathophysiological changes in multiple organs often resulting in life threatening clinical outcomes e.g. breast and colon cancer, pancreatic disease, cirrhosis of the liver, diabetes, osteoporosis, arthritis, kidney disease, immune system dysfunction, hypertension, coronary artery disease, alcohol-induced cardiomyopathy and heart failure as well as central nervous system disorders. In this review article, we will discuss the multisystemic effects of alcohol abuse and explore in greater detail alcohol’s impact on two main systems that result in pathophysiological changes i.e. the cardiovascular and central nervous systems.