Ionic gel electrolyte retains the characteristics of non-volatilization, non-flammability and outstanding electrochemical stability of ionic liquid, and shows good electrochemical performance combined with the excellent characteristics of different matrix materials, which is considered to be the best choice to achieve the high energy density and safety at the same time. In this paper, a flexible and self-healing ionic gel electrolyte is prepared by solvent-assisted method based on a zteric ion (ZI) copolymer. Abundant hydrogen bonds and synergistic interaction of ions in the electrolyte system endowed it with wonderful self-healing ability. The ionic conductivity of 9.06×10-4 S cm-1 at room temperature was achieved. Besides, the tLi+ was also increased to 0.312. The self-healing function of the ionic gel electrolyte ensured the long-term tolerance of the SHIGE. The capacity retention rate of the Li//LiFePO4 battery is 96% after 155 cycles at 0.1 C at 60 oC. This polymer electrolyte is expected to solve the problem of increasing polarization，which is caused by the low lithium ions migration number in ionic liquid electrolyte. And ultimately, it gives rise to a good rate performance.

Evidence of the efficacy and safety of colorectal stent placement for palliation remains insufficient. This single-arm, prospective, multicenter study with WallFlex enteral colonic stent included 200 consecutive patients with malignant large bowl obstruction in the palliation cohort. The technical and clinical success, as well as stent patency and complications as short-term (≤ 7 days) and long-term (> 7days) outcomes, of high axial force self-expandable metal stent (SEMS) placement was evaluated. The technical and clinical success rates were 98.5% and 94.5%, respectively. Non recurrent colorectal obstruction at 1 year was 63.9%, and 71.2% of the patients remained free of recurrent colorectal obstruction until death or the last follow-up. Fifty-six patients (28.0 %) received chemotherapy and five patients were administered bevacizumab after stent placement. The overall complication rate was 47%, including four (2.0%) early-onset and ten (5.0%) late-onset perforations, mostly due to stent-edge injury. Only the use of a long SEMS was a risk factor for perforation. In conclusion, endoscopic colorectal stenting using high axial force SEMS is an effective and safe procedure for palliation in patients with malignant colorectal obstruction. However, care should be taken to avoid perforation at the stent edge when using a long SEMS.

To study the influence of electrothermal effect of ESD protection device on the reliability of inte-grated circuit,a theoretical model of ESD protection device thermal resistance is constructed in the paper based on the Conservation of Energy Principle. By analyzing the temperature relativity between electricity parameter and thermology parameter of ESD protection device characterized by self-heating thermal resistance, the quantitative relationship expression of physical parameter and geometric parameter is obtained, which can be used to improve ESD protection device elec-tro-thermal effect. The simulation testing and the real tape-out testing of ESD protection device self-heating thermal resistance based on ggNMOS are shown and compared. It is concluded that self-heating thermal resistance is an effective index for the protection device electrothermal char-acterization. Based on the established model, the self-heating thermal resistance could be decreased to improve the homogeneity of the heat transference. The uneven distribution of device temperature can be reduced, and the overall reliability of chips can be improved.

The spike protein (S) of SARS-CoV-2 has been shown to bind to the human angiotensin-converting enzyme 2 (ACE2) receptor with much higher affinity compared to other coronaviruses. The binding interface between the ACE2 receptor plays a critical role in the entry mechanism of SARS-CoV-2 virus. There are specific amino acids involved in the interaction between S protein and ACE2 receptor. This specificity is critical for the virus to establish a systemic infection and cause COVID-19 disease. In the ACE2 receptor, the largest number of amino acids that play a crucial role in the mechanism of interaction and recognition with the S protein are located in the C-terminal part which represents the main binding region between ACE2 and S. This fragment is abundant in coordination residues such as aspartates, glutamates and histidine that could be targeted by metal ions. Zn²⁺ ion binds to the ACE2 receptor in its catalytic site and modulates its activity, but it could also contribute to the structural stability of the entire protein. The ability of the human ACE2 receptor to coordinate metal ions, such Zn²⁺, in the same region where it binds to the S protein could have a crucial impact in the mechanism of recognition and interaction of ACE2-S with consequences on their binding affinity that deserve to be investigated. To test this possibility, this study aims to characterize the coordination ability of Zn²⁺, and also Cu²⁺ for comparison, with selected peptide models of the ACE2 binding interface using spectroscopic and potentiometric techniques.

Endoscopic ultrasound-guided gallbladder drainage (EUS-GBD) is an alternative to surgery for acute cholecystitis (AC) in poor operative candidates. However, the role of EUS-GBD in non-cholecystitis (NC) indications has not been well studied. We compared clinical outcomes of EUS-GBD for AC and NC indications. Consecutive patients undergoing EUS-GBD for all indications at a single center were retrospectively analyzed. Fifty-one patients underwent EUS-GBD during the study period. Thirty-nine (76%) patients had AC while 12 (24%) had NC indications. NC indications included malignant biliary obstruction (n = 8), symptomatic cholelithiasis (n = 1), gallstone pancreatitis (n = 1), choledocholithiasis (n = 1), and Mirizzi’s syndrome (n = 1). Technical success was noted in 92% (36/39) for AC and 92% (11/12) for NC (p > 0.99). Clinical success rate was 94% and 100%, respectively (p > 0.99). There were 4 adverse events in the AC group and 3 in the NC group (p = 0.62). Procedure duration (median 43 vs 45 minutes, p = 0.37), post-procedure length of stay (median 3 vs 3 days, p = 0.97), and total gallbladder related procedures (median 2 vs 2, p = 0.59) were similar. EUS-GBD for NC indications is similarly safe and effective as EUS-GBD in AC.

Two solvated rhenium(IV) complexes with formula [ReCl4(bpym)]·MeCN (1) and [ReCl4(bpym)]·CH3COOH·H2O (2) [bpym = 2,2'-bipyrimidine] have been prepared and characterized by means of Fourier transform infrared spectroscopy (FT–IR), scanning electron microscopy and energy dispersive X-ray analysis (SEM–EDX), single-crystal X-ray diffraction (XRD) and SQUID magnetometer. 1 and 2 crystallize in the monoclinic system with space groups P21/n and P21/c, respectively. In both compounds, the Re(IV) ion is six-coordinate and bound to four chloride ions and two nitrogen atoms of a 2,2’-bipyrimidine molecule forming a distorted octahedral geometry around the metal ion. In the crystal packing of 1 and 2, intermolecular halogen⋯halogen and π⋯halogen type interactions are present. Hydrogen bonds take place only in the crystal structure of 2. Both compounds exhibit an akin crystal framework based on halogen bonds. Variable-temperature dc magnetic susceptibility measurements performed on microcrystalline samples of 1 and 2 show a similar magnetic behavior for both compounds, with antiferromagnetic exchange between the Re(IV) ions connected mainly through intermolecular Re-Cl···Cl-Re interactions.

We have detected a large Nernst effect in the CDW state of the multiband organic metal α−(BEDT−TT)2KHg(SCN)4. We find that there exists a significant gradient of charge relaxation processes that can generate a sizeable contribution adding especially to the transverse thermoelectric signal. Apart from the phonon drag, the energy relaxation processes governing the electron-phonon interactions and the momentum relaxation processes governing the charge mobility of the q1D group of carriers have a significant role in observing the large Nernst signal in the CDW state. The emphasised momentum relaxation dynamics in the low field CDW state is a clear indicator of a significant carrier mobility that can lead to the largest Nernst signal in this state. The momentum relaxation is reduced with increasing angle and magnetic field, i.e., in the high field CDW state which is reflected in the smaller Nernst effect amplitude. In this case only the phonon drag and electron-phonon interactions are contributing to the transverse thermoelectric signal. Our findings advance and change the previous observations on the complex properties of this organic metal.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

All living organisms require some metal ions for their energy production as well as metabolic and biosynthetic processes. Within cells, metal ions are involved in the formation of adducts interact with metabolites and macromolecules (proteins and nucleic acids). The proteins that require binding to one or more metal ions to be able to carry out their physiological function are called metalloproteins. About one third of all protein structures in the Protein Data Bank involve metalloproteins. Over the past few years there has been a tremendous progress in the number of computational tools and techniques making use of 3D structural information to support the investigation of metalloproteins. This trend has been boosted also by the successful applications of neural networks and deep learning approaches in molecular and structural biology at large. In this review, we discuss recent advances in the development and availability of resources dealing with metalloproteins from a structure-based perspective. We start by addressing tools for the prediction of metal-binding sites (MBSs) using structural information on apo-proteins. Then, we provide an overview of methods for and lessons learned from the structural comparison of MBSs in a fold-independent manner. We then move to describing databases of metalloprotein/MBS structures. Finally, we summarize recent DL applications enhancing the functional interpretation of metalloprotein structures.

We report a prebiotically relevant solution to the N1-ribosylation of pyrimidine nucleobases, a well-known challenge in the RNA World hypothesis. It is found that the presence of metal cations and clay mineral enables the previously unachievable direct ribosylation of uracil, providing by far the highest yield. Spectroscopy and chromatography analyses confirmed the formation of ribosylated uracil. The method can also be extended to the ribosylation of 2-pyrimidinone. These findings are also compatible with the metal-doped-clay model developed by our lab for the unified route of the selection of ribose and subsequent syntheses of nucleotide and RNA.

The present study utilizes a metal inert gas welding (MIG) to make a dissimilar weld joint of different stainless steel grades AISI 304, 314, 316L, 420 and a standard structural steel S355MC to estimate the correlation of a microstructure and the mechanical properties. The microstructure of the base metals (BM), the heat affected zone (HAZ), the fusion zone (FZ) and the weld seam were analyzed using optical microscopy. Optical microscopy did not reveal any presence of weld defects such as porosity or cracks. The analysis of microstructure showed that both the austenitic and martensitic stainless steel weld structures contain some retained delta ferrite and coarse Me23C6 carbides in the HAZ, while the FZ exhibits delta ferrite and some retained austenite. The hardness profiles revealed difference between austenitic and martensitic steel welds that the later showed extremely high values in the HAZ (~500 HV/0.1) which causes fracture in this zone. The welds of all austenitic steel grades withstood tensile test, showing the average tensile strength of 472 MPa with fracture observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds, and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.

The screening and treatment of acid mine drainage (AMD) using Na₂FeO₄ has been explored. Elemental composition was performed using an ICP-OES for the raw and treated AMD. The AMD samples were collected from three different sampling sites (RTW1, RTW2 and RTW3) in Pretoria, South Africa with acidic pH ranging between 2.50 and 3.13. Total dissolved solids and Electrical Conductivity of AMD samples ranged between 960 and > 1000 mg. L^-1, 226 and 263 µS. cm^-1, respectively. The final pH of treated water samples increased up to ≥ 9.5 after treatment with Na₂FeO₄. Sodium ferrate showed dual functions by removing metals and raising the pH of the treated water. Concentrations of most trace elements were not complying with WHO and DWAF guideline standards in raw AMD while after treatment with Na₂FeO₄ the concentrations were below guidelines for domestic and irrigation purposes.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

Alzheimer’s disease (AD) is one of the most prevailing neurodegenerative diseases, characterized by memory dysfunction and the presence of hyperphosphorylated tau and amyloid β (Aβ) aggregate in multiple brain regions, including the hippocampus and cortex. The exact etiology of AD has not yet been confirmed. However, epidemiological reports suggest that populations who were exposed to environmental hazards are more likely to develop AD than those who were not. Arsenic (As) is a naturally occurring environmental risk factor abundant in the Earth’s crust and human exposure to As predominantly occurs through drinking water. Convincing evidence suggests that As causes neurotoxicity and impairs memory and cognition although the hypothesis and molecular mechanism of As-associated pathobiology in AD are not clear yet. However, exposure to As and its metabolites leads to various pathogenic events such as oxidative stress, inflammation, mitochondrial dysfunctions, ER stress, apoptosis, impaired protein homeostasis, and abnormal calcium signaling. Evidence has indicated that As exposure induces alterations that coincide with most of the biochemical, pathological, and clinical developments of AD. Here, we overview existing literature to gain insights into the plausible mechanisms that underlie As-induced neurotoxicity and the subsequent neurological deficits in AD. Prospective strategies for the prevention and management of arsenic exposure and neurotoxicity have also been discussed.

Aiming the characterization of road dusts on the surrounding villages of an active mine and to assess metal(loids) bioaccessible fractions, a dust samples survey was undertaken. To achieve these objectives, pseudototal element concentration, mineralogical composition, Enrichment factor and in vitro extraction UBM assay for both gastric (G) and gastrointestinal (GI) phases, were determined. Results obtained revealed that arsenic represents the higher risk to humans, with mean pseudototal values higher than the maximum reference value range. Enrichment factor points to As significant to very high enrichment in all villages. Particles enriched in As, Ca, Fe, Cu, Al, Ti were identified by SEM-EDS in weathered agglomerates, linked to mine wastes and long-distance transport, both by wind and/or traffic. Arsenic bioaccessibility fraction (%BAF) presents low values in the studied samples, possibly due to low Fe complexes solubility with adsorbed As, limiting arsenic release and reducing its bioaccessibility. Concentrations of Cd bioaccessible G and GI phases are within the reference values range, while for Cu are above and for Pb are lower, than reference value range. Results show that the pseudototal fraction risk is overestimated when comparing to BAF (bioaccessible fraction), nevertheless, total G and GI risk are above the carcinogenic target risk (1.00E-06) in most samples. Carcinogenic risk of the bioaccessible contaminants shows that As is the element that represents higher risk for developing cancer over a lifetime, being ingestion the main risk route.

: Dacarbazine, DAC, 5-(3,3-dimethyltriazeno)imidazol-4-carboxamideis is an imidazole-carboxamide derivative, that is structurally related to purines. DAC belongs to the triazene compounds, which are a group of alkylating agents with antitumour and mutagenic properties. DAC is a non-cell cycle specific drug, active on all phases of cellular cycle. In the frame of this work the 3d-metal complexes (cobalt and copper) with dacarbazine were synthesized. Their spectroscopic properties by the use of FT-IR, FT-Raman and 1HNMR were studied. The structures of dacarbazine and its complexes with copper(II) and cobalt(II) were calculated using DFT methods. The effect of metals on the electronic charge distribution of dacarbazine was discussed on the basis of calculated NBO atomic charges. The reactivity of metal complexes in relation to ligand alone was estimated on the basis of calculated energy of HOMO and LUMO orbitals. The aromaticity of imidazole ring in dacarbazine and the complexes was compared (on the basis of calculated geometric indices of aromaticity). Thermal stability of the investigated 3d-metal complexes with dacarbazine and the products of their thermal decomposition were analyzed.

The paramagnetic gadolinium(III) ion is used as contrast agent in magnetic resonance (MR) imaging to improve the lesion detection and characterization. It generates a signal by changing the relaxivity of protons from associated water molecules and creates a clearer physical distinction between the molecule and the surrounding tissues. New gadolinium-based contrast agents displaying larger relaxivity values and specifically targeted might provide higher resolution and better functional images. We have synthesized the gadolinium(III) complex of formula [Gd(thy)2(H2O)6](ClO4)3·2H2O (1) [thy = 5-methyl-1H-pyrimidine-2,4-dione or thymine], which is the first reported compound based on gadolinium and thymine nucleobase. 1 has been characterized through vis-IR, SEM-EDAX and single-crystal X-ray diffraction techniques, and its magnetic and relaxometric properties have been investigated by means of SQUID magnetometer and MR imaging phantom studies, respectively. On the basis of its high relaxivity values, this gadolinium(III) complex can be considered a suitable candidate for contrast enhanced magnetic resonance imaging.

Bacteria a Microscopic organisms are the most inexhaustible and flexible of microorganisms and constitute a huge division of the whole living earthly biomass, certain microorganisms were found to amass metallic components at a high limit Was Known as Bacterial Bio-sorption Due to their little size, capacity to become under controlled conditions, and their Accommodation to an extensive variety of ecological situations; Potent metal bio-sorbents among microorganisms, at low pH esteems, cell divider ligands are protonated and contend essentially with metals for official. With expanding pH, more ligands, such as amino and carboxyl groups, could be exposed, leading to attraction between these negative charges and the metals, and consequently increment bio-sorption onto the cell surface. Starting with Isolation and identification of heavy metal-resistant bacteria from rock Ore. Studying Factors Affecting Uranium Bio-sorption, Optimization of bacterial growth conditions and optimum for metal uptake by free and immobilized bacterial cells and Desorption ratio of uranium ions adsorbed by Coli. /alginate, All this evidence suggest that functions groups Represented in our study are responsible for metal uptake in our bacterial biomass beside change in peaks position which assigned for it's groups confirm bio-sorption of metal ions from waste due to ions charge interaction comparing with immobilized we found increase in no of binding sites indicate that immobilized bacterial have high efficiency for metal up take which also change in peaks position which assigned for its groups confirm bio-sorption of metal ions from waste due to ions charge interaction, Where the high bio-sorption yield obtained by bacteria, the Uranium & heavy metal bioremediation process expects microorganisms to be joined to a strong surface.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

Hybrid metal-organic compounds as relatively new and prosperous magnetoelectric multiferroics provide opportunities to improve the polarization, magnetization and magneto-electric coupling at the same time, which usually have some limitations in the common type-I and type-II multiferroics. In this work we investigate the crystal of guanidinium copper(II) formate [C(NH2)3]Cu(HCOO)3 and give novel insights concerning the structure, magnetic, electric and magneto-electric behaviour of this interesting material. Detailed analysis of crystal structure at 100 K is given. Magnetization points to the copper(II)-formate spin-chain phase that becomes ordered below 4.6 K into the canted antiferromagnetic (AFM) state, as a result of super-exchange interaction over different formate bridges. The performed ab-initio colinear density functional theory (DFT) calculation confirm the AFM-like ground state as a first approximation and explain the coupling of spin-chains into the AFM ordered lattice. In versatile measurements of magnetization of a crystal, including transverse component besides the longitudinal one, very large anisotropy is found that might originate from canting of the coordination octahedra around copper(II) in cooperation with the canted AFM order. With cooling down in zero fields the generation of spontaneous polarization is observed step-wise below 270 K and 210 K and the effect of magnetic field on its value is observed also in the paramagnetic phase. Measured polarization is somewhat smaller than the DFT value in the c-direction, possibly due to twin domains present in the crystal. The considerable magneto-electric coupling below the magnetic transition temperature is measured with different orientations of the crystal in magnetic field, giving altogether the new light onto the magneto-electric effect in this material.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

Both types of surgical guides – with and without metal sleeves are founded beneficial in clinical studies. The aim of this in vitro study was to compare time of surgical procedure in dental implantology depending of used type of the surgical guide. Ten three dimensional (3D) printed models of lower jaws were prepared based on complete virtual model of patient clinical conditions with missing teeth 37, 46 and 47. Five of this models were used for implant sites preparation performed with use of surgical guide without metal sleeves and dedicated surgical kit, and next five were used for the same procedure performed with surgical guide with metal sleeves and dedicated surgical kit. Time of implant site preparation were measured and noted. Statistical analysis was performed using Student’s t test for independent samples. Difference of time in both groups were founded as statistically significant (t=-9.94; df =28; p=0.0000). Type of surgical guide is important factor which can impact on time of implant site preparation and all surgical procedure.

Sorghum is a multipurpose crop, but Cr(VI) toxicity influenced the production of the crop and have established highlighted courtesy, due to robust toxicity and a comparatively less known mode of action. Many reports approve the negative impact of Cr(VI) on plants. Yet, it is not clear that, at what concentrations, Cr(VI) inhibits the growth and nutrient quality of Sorghum. In the present research, toxic effects appeared after 1ppm of Cr treatment. The plant growth decreased 15 – 20% and nutritional quality decreased 30 – 40% significantly with increasing concentration of Cr(VI). Toxic components increased 14 – 16% with increasing concentration of Cr(VI) in both the varieties (HJ 541 and SSG 59-3). Chromium was accumulated more in roots followed by shoots with increasing Cr(VI) treatments (0-4 ppm). Chromium at 4ppm level was becoming lethal to Sorghum. Sorghum cultivar SSG 59-3 was more tolerable to Cr toxicity than HJ 541. Chromium accumulated in Sorghum and increased HCN content and at higher doses adversely affects the nutritive values and growth making it toxic for animal consumption. These findings may be useful for scheming a mitigation strategy for chromium toxicity.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

Understanding potential uptake and biodistribution of engineered nanoparticles in soil-grown plants is imperative for toxicity and risk assessment considering the oral exposure of edibles by humans. Herein, we assessed potential influence of particle size (25, 50, and 250 nm) and concentration (0, 50, 100, 200, and 500 mg/kg-soil) of Copper oxide nanoparticles (CuONPs) on: (1) the root system architecture, and the physicochemical attributes of soil at the soil-root interface, (2) leading to Cu transport and accumulation in root, stem, leaf and seed in soybean (Glycine max cv Kowsar) grown for entire lifecycle of 120 days, and compared with soluble Cu²⁺ ions and water-only controls, and (3) performed a comparative assessment of total seed Cu levels in soybean with other valuable food sources for Cu intake and discussed its human health implications. Our findings showed particle size- and concentration-dependent influence of CuONPs on Cu uptake and tissue distribution in root, stem, leaf and seed in soybean. Alterations in root architecture (root dry weight, root length, root volume, and root area) were dependent on the Cu compound type, Cu concentrations, and their interactions (p<0.05), except for root density. Concentration-response relationships for all three sized CuONPs, and Cu²⁺ ions, were linear. CuONPs and Cu²⁺ ions had inhibitory effects on root growth and development. Overall, soybean responses to smallest size CuONPs-25 nm were higher for all parameters investigated compared to two larger sized CuONPs (50 nm, 250 nm) or Cu²⁺ ions. Cu uptake/bioaccumulation differed among soybean tissues in the order: root > leaf > stem > seed. Despite reduced root architecture and seed yield, our smallest size CuONPs-25 nm led to increased total seed Cu uptake compared to the larger sized CuONPs and Cu²⁺ ions tested. Our findings also suggest that soil amendment by CuONPs, more so by the smallest size CuONPs-25 nm, could significantly improve nutritional Cu value in soybean seed as reflected by % Daily Values (DV), and are rated “Good” to “Very Good” according to the “World’s Healthiest Foods” rating. However, until the potential toxicity and risk from consumption of soybean seed is characterized in humans, caution should be exercised when the Cu fortified seeds are used for daily human consumption when addressing Cu deficiency and associated illnesses, globally.

In this paper, a metal cutting machine position control have been designed and simulated using Matlab/Simulink Toolbox successfully. The open loop response of the system analysis shows that the system needs performance improvement. Static output feedback and full state feedback H₂ controllers have been used to increase the performance of the system. Comparison of the metal cutting machine position using static output feedback and full state feedback H₂ controllers have been done to track a set point position using step and sine wave input signals and a promising results have been analyzed.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

Food preservatives are compound that are used for the treatment of food to improve the shelf life. In the food industry, is necessary to monitor all processes, for both safety and quality of the product. An electronic nose (or e-nose) is a biomimetic olfactory system that could find numerous industrial applications, including food quality control. Commercial electronic noses are based on sensor arrays composed by a combination of different sensors, which include conductometric metal oxide devices. Metal oxide nanowires are considered among the most promising materials for the fabrication of novel sensing devices, which can enhance the overall performances of e-noses in food applications. In the present work, is reported the fabrication of a novel sensor array based on SnO2, CuO and WO₃ nanowires deposited on top of commercial μHPs, provided by ams Sensor Solutions Germany GmbH. The array was tested for the discrimination of four typical compounds added to food products or used for their treatment to increase the shelf life: ethanol, acetone, nitrogen dioxide and ozone. Results are very promising: the sensors array was able to operate for long time consuming less than 50mW for each single sensor, and PCA analysis confirms that the device was able to discriminate between different compounds.

The optimization of the production process of metal mines has been traditionally driven only by economic benefits while ignoring resource efficiency. However, it has become increasingly aware of the importance of resource efficiency since mineral resource reserves continue to decrease while the demand continues to grow. To better utilize the mineral resources for sustainable development, this paper proposes a multi-objective optimization model of the production process of metal mines considering both economic benefits and resource efficiency. Specifically, the goals of the proposed model are to maximize the profit and resource utilization rate. Then, the fast and elitist Non-Dominated Sorting Genetic Algorithm (NSGA-II) is used to optimize the multi-objective optimization model. The proposed model has been applied to the optimization of the production process of a stage in the Huogeqi Copper Mine. The optimization results provide a set of Pareto-optimal solutions that can meet varying needs of decision makers. Moreover, compared with those of the current production indicators, the profit and resource utilization rate of some points in the optimization results can increase respectively by 2.99% and 2.64%. Additionally, the effects of the decision variables (geological cut-off grade, minimum industrial grade and loss ratio) on objective functions (profit and resource utilization rate) were discussed using variance analysis. The sensitivities of the Pareto-optimal solutions to the unit copper concentrate price were studied. The results show that the Pareto-optimal solutions at higher profits (with lower resource utilization rates) are more sensitive to the unit copper concentrate prices than those obtained in regions with lower profits.

Light sources tend to affect images captured in any automatic optical inspection (AOI) system. In this study, the effectiveness of metal-halide lamps, quartz-halogen lamps, and LEDs as the light sources in AOI systems for the detection of the 3rd and 4th layers electrodes of thin-film-transistor liquid crystal displays (TFT-LCDs) is examined experimentally. The results show that the performance of LEDs is generally comparable or better than that of metal-halide and quartz-halogen lamps. The best optical performance is by the blue LED due to its spectrum compatibility with the time-delay-integration charged-coupled device (TDI CCD) sensor and its better spatial resolution. The images revealed by the blue LED are sharper and more distinctive. Since current LEDs are more energy efficient and environmentally friendly, using LEDs as the light source for AOI is very beneficial. As the blue LED performs the best, it should be adopted for AOI using TDI CCD sensors.

The apparent metal-insulator transition (MIT) in two-dimension (2D) was discovered by Kravchenko et al. [1] more than two decades ago in strongly interacting 2D electrons residing in a Si-metal-oxide-semiconductor field-effect transistor (Si-MOSFET). Its origin remains unresolved. Recently, low magnetic field reentrant insulating phases (RIPs), which dwell between the zero-field (B=0) metallic state and the integer quantum Hall (QH) states where the Landau-level filling factor υ > 1, have been observed in strongly correlated 2D GaAs hole systems with large interaction parameter rs (~20-40) and high purity. A new complex phase diagram was proposed, which includes zero field MIT, low magnetic field RIPs, integer QH states, fractional QH states, high field RIPs and insulating phases (HFIPs) with υ < 1 in which the insulating phases are explained by the formation of Wigner crystal. Furthermore, evidences of new intermediate phases were reported. All contribute to the further understandings of the puzzle. This review article serves the purpose of summarizing those recent experimental findings and theoretical endeavors, to foster future research efforts.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

To remove sulfur-containing compounds (SCC) from the diesel fraction 200-360 °C extraction systems have been created based on coordinating organic solvents - dimethylformamide and dimethylsulfoxide and chlorides (CoCl2, CuCl2, CdCl2, MnCl2 and CrCl3) and metal trifluoroacetates (Co (TFA)2, Cu(TFA)2 and Mn(TFA)2). Using PMR spectroscopy the coordination of chloride and metal trifluoroacetate on the oxygen atom in the carbonyl group of DMFA was shown to redistribute electron density in the solvent molecule and to enhance properties of the acceptor center localized on the nitrogen atom. The removal of sulfur-containing compounds from the diesel fraction proceeded under mild conditions - at the temperature of 25 °C and atmospheric pressure. The degree of SCC removal from the diesel fraction in 30 minutes extraction was more than 90%. The interaction of organic solvents with metal salts and sulfur-containing compounds of the diesel fraction was considered within the framework of the concept of "hard and soft acids and bases" (HSAB). The most complete SCC extraction was carried out by "DMFA - Mn(TFA)2, MnCl2 and CrCl3 systems, that was probably connected with the implementation of the" hard base - hard acid "system.

Slow and controlled release systems for drugs, have attracted increasing interest recently. A highly efficient metal-organic gels (MOGs) drug delivery carrier, i.e., MIL-100(Al) gels, has been fabricated by a facile, low cost and environment friendly one-pot process. The unique structure of MIL-100(Al) gels leads to a high loading efficiency (620 mg/g) towards doxorubicin hydrochloride (DOX) as a kind of anticancer drugs. DOX-loaded MOGs exhibited high stability under physiological conditions and sustained release capacity of DOX for up to 3 days (under acidic environments). They further showed sustained drug release behavior and excellent antitumor effects in in vitro experiments on HeLa cells, in contrast with the extremely low biotoxicity of MOGs. Our work provides a promising way for the anticancer therapy, by utilizing this MOGs-based drug delivery system, as an efficient and safe vehicle.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

1) Background: Bipolar or manic-depressive disorder is a malign mental disease that frequently faces social stigma. Educational and thinking models are needed to increase people’s awareness and understanding of the disorder. The arts have potential to achieve this goal. 2) Methods: This paper builds on the recent use of heavy metal music as a thinking and education model. It emphasizes the artistic component of heavy metal and its potential to characterize the symptomatology during the episodes of (hypo)mania and depression and the recurrence of these episodes. Heavy metal music has diversified into subgenres that become allegorical to both the symptoms of episodes and the recurrence of bipolar cycles. 3) Results: Examples of songs are given that mirror distinct facets of the disorder. 4) Conclusion: Although the links drawn between art (music) and science (psychiatry) are inherently subjective, such connections might be used to trigger a learning process, facilitate judgment and decision-making, and induce affective reactions and memory formation in the listener. The approach may facilitate collaborative efforts and serve healthcare professionals and educators as a communication tool to aid the public’s comprehension of the disease and an associated social paradox: On one hand, bipolar disorder incurs substantial costs to society. On the other hand, it benefits from the creative artistic and scientific endeavors of bipolar individuals from which cultural and political gains may ensue.

This study addresses the global issue of recycling used vehicle rubbish tires, typically burned out or trimmed to be reused in playground floors or road banks. In this study we explore a novel environmentally responsive approach or decomposing and recovering the carbon black particles contained in tires (25-30 wt.%) by vacuum pyrolysis. Given that carbon black is well known for its UV protection in plastics, the objective of this research is to provide an ecological alternative to commercial carbon black of fossil origin by recycling the carbon black (rCB) from used tires. In our research, we create a composite material using rCB and high density polyethylene (HDPE). In this article we present the environmental aging studies carried out to this composite material. The topographic evolution of the samples with aging and the oxidation kinetic of the surface and through the thickness were studied. A Beer-Lambert law is used to relate the oxidative index to the characteristic depth of the samples. This work helps to demonstrate the feasibility of using recycled carbon black particles from waste tires as a filler for UV protection.

This ambitious research project seeks to revolutionize sustainable glucose production by harnessing solar energy for the conversion of atmospheric gases. The process involves water collection, electrolysis for hydrogen and oxygen production, PDMS membrane-based CO2 collection, CO2 splitting, formaldehyde generation, and the synthesis of glucose/sucrose. Key innovations include the strategic application of PDMS membranes with varying pore sizes and non-reactive chemical layers to facilitate selective permeability for specific gases. Our goal is to create a cost-effective, eco-friendly glucose production method, paving the way for renewable and sustainable energy solutions.

The Brazilian Pantanal region suffers intensely from biomass burning during the dry season. Large quantities of gases and particles are emitted into the atmosphere during this period, with serious implications for fauna and flora. Understanding the dynamics of these emissions is es-sential for mitigating the ecosystem, its functioning, and possible anthropogenic disturbances. In this sense, this study analyzed emissions over the north of the Brazilian Pantanal during the 2022 drought. Measurements of concentration of fine particulate matter (PM2.5), Black carbon (BC), and elemental concentration (25 chemical elements) were determined by gravimetry, reflectance analysis, and X-ray fluorescence, respectively, for samples collected between August and Octo-ber 2022. The average concentrations of PM2.5 and BC had their values increased by approxi-mately 4 and 2.5 times, respectively, when compared to the averages from a decade ago. The maximum concentrations found are close to values typical of the southern Amazon region, a re-gion with high rates of deforestation and changes in land use. The elemental analysis showed large changes in concentrations, mainly associated with biomass burning emission (BB) and soil resuspension. Furthermore, analyses of lead (Pb) concentrations showed strong anthropization at the study site.

This study investigates the impact of plasma gradient modification and gradient illumination on the optoelectronic properties of buckypaper (BP), a flexible and large-scale material composed of multi-walled carbon nanotubes (MWCNTs). The BP samples were subjected to argon ion plasma treatment at varying power levels and durations, thereby creating different carrier concentration gradients on the surface. The photovoltage and photocurrent responses of the samples were then measured under uniform full illumination and gradient illumination conditions. The findings revealed that both plasma gradient modification and gradient illumination significantly enhanced the optoelectronic performance of BP. Notably, the combined application of these two methods yielded superior results compared to the application of either method alone. Specifically, the optimal plasma power for improving BP was found to be 20W. Under conditions of plasma gradient modification and gradient illumination, a photovoltage of 267.76 μV was generated, which represents a 21.44 times increase, and a photocurrent of 15.69 μA, reflecting a 32.69 times enhancement. The mechanism underlying this optoelectronic effect can be attributed to the presence of π-bonds in the carbon atoms. These π-bonds are excited by photons, resulting in the generation of small voltages and currents. This study underscores the potential of BP as an optoelectronic material and introduces a novel approach to enhance its optoelectronic properties through plasma gradient modification and gradient illumination.

Thermal analysis is widely employed for the characterization of nanomaterials. It encompasses a variety of techniques that allow the evaluation of the physicochemical properties of a material by monitoring its response under controlled temperature. In the case of carbon nanomaterials, such as carbon nanotubes and graphene derivatives, thermogravimetric analysis (TGA) is particularly useful to determine the quality and stability of the sample, presence of impurities and the degree of functionalization or doping after post-synthesis treatments. Furthermore, TGA is widely used to evaluate the thermal stability against oxidation by air, which can be for instance enhanced by the purification of the material and by nitrogen doping, finding application in areas where a retarded combustion of the material is required. Herein, we have evaluated key parameters that play a role in the data obtained from TGA. Within this study we show that the thermogravimetric curve of carbon nanomaterials is greatly influenced by these parameters. This is important in terms of data recording and their analysis, since a poor control of the conditions of measurement might lead to false conclusions. We highlight this by analyzing different samples of graphene and carbon nanotubes where both thermal stability and sample purity assessment are found to be dependent on the employed TGA parameters. Finally, a set of TGA parameters are recommended for the analysis of carbon nanomaterials to obtain reliable data.¡

The escalating global demand for clean water has propelled research into sustainable and cost-effective purification methods. Activated carbon (AC) derived from biowaste materials presents an environmentally friendly and economically viable solution for water treatment. This review article provides an extensive overview of the synthesis techniques, characterization methods, and applications of biowaste activated carbon (BAC) for water purification. It discusses the diverse sources of biowaste, such as agricultural residues, food waste, and biomass, and explores various activation methods including physical, chemical, and biological processes. Furthermore, the article examines the adsorption mechanisms, performance factors, regeneration strategies, and emerging trends in BAC synthesis and application. Insights from this review can guide future research endeavors and facilitate the development of sustainable water purification technologies.

Glassy carbon (GC) microelectrodes have been successfully used for detection of electroactive neurotransmitters such as dopamine and serotonin through voltammetry. However, non-electroactive neurotransmitters such as glutamate, lactate, and gamma-aminobutyric acid (GABA) are inherently unsuitable for detection through voltammetry techniques without functionalizing the surface of the microelectrodes. To that end, we present here the immobilization of L-glutamate oxidase (GluOx) enzyme on the surface of GC microelectrodes to enable catalysis of chemical reaction between L-glutamate, oxygen, and water to produce H2O2, an electroactive byproduct that is readily detectable through voltammetry. This immobilization of GluOx on the surface of bare GC microelectrodes and the subsequent catalytic reduction of H2O2 through fast scan cyclic voltammetry (FSCV) helped demonstrate indirect in vitro detection of glutamate, a non-electroactive molecule, at concentrations as low as 10 nM. The functionalized microelectrodes formed part of 4-channel arrays of microelectrodes (30 m x 60 m) on a 1.6 cm long neural probe supported on a flexible polymer, with potential for in vivo applications. The type and strength of the bond between the GC microelectrode surface and its functional groups on one hand, and glutamate and the immobilized functionalization matrix on the other hand, were investigated through molecular dynamics (MD) modeling and Fourier Transform Infrared Spectroscopy (FTIR). Both MD modeling and FTIR demonstrated the presence of several covalent bonds in the form of C-O (carbon-oxygen polar covalent bond), C=O (carbonyl), C-H (alkenyl), N-H (hydrogen bond), C-N (carbon-nitrogen single bond), and C≡N (triple carbon nitrogen bond). Further, penetration tests on agarose hydrogel model confirmed that the probes are mechanically robust with their penetrating forces being much lower than the fracture force of the probe material.

This study focuses on solving rural problems, sustaining environmental conditions, pastures improvement, and reduction of CO2 concentration, suggesting inoculated vegetation types found in the tropics as a nature-based solution for degraded agroecosystems. Noninoculated plants are intensively used for revegetation of degraded and mined lands, AMF taxonomic and plant-fungal ecological studies. Among those grasses, Urochloa brizantha is a tropical forage, having vigorous deep roots, commonly used for arbuscular mycorrhizae (AMF) multiplication in glasshouse and nursery, developing infective propagules to be conserved in germplasm banks. Other grass species, such as Urochloa decumbens, is also used for arbuscular mycorrhizal multiplication in addition to its cultivation for guaranteeing the sustainable of livestock systems. In the present study, a site of 100 m2 was selected to take soil samples in a plain area, with U. brizantha pasture, and the soil chemical characterization, microcharcoal content and AMF spore identification, were evaluated 3+6showing high amount of potassium (K), high microcharcoal content and the occurrence of 11.32 spores of AMF, most of Glomeraceae, in the rhizosphere of U. brizantha. Due to its economic importance for sustainable agricultural production and other uses besides its environmental services, as important promoters of soil carbon on grazing lands, more detailed research is needed on the biotic interactions and inoculant production in of the studied grasses.

Emulsifiers like egg yolk (EY) are necessary for the formation of mayonnaise, which is an oil-in-water type colloid. This study aimed to assess the potential of defatted soybean powder treated with supercritical carbon dioxide (DSF-SC) in enhancing the quality of plant-based may-onnaise as plant-based alternatives gain popularity. This study involved producing DSF-SC and comparing its quality attributes to those of mayonnaise made with varying amounts of control soy flour (CSF), DSF-SC, and EY. It was found that mayonnaise made with DSF-SC, with increased emulsifier quantity, showed better emulsion stability, viscosity, and smaller, more uniform particle size compared with CSF mayonnaise. Additionally, DSF-SC mayonnaise was overall rated higher in sensory evaluation. The addition of approximately 2% DSF-SC positively influenced the emul-sion and sensory properties of the vegan mayonnaise, making DSF-SC a promising plant-based alternative emulsifier for replacing animal ingredients.

This study deals with the preparation of adsorbents from a commercial xerogel by chemically modifying its surface with concentrated mineral acids and alkali metal chlorides, their physicochemical characterization, and their use as adsorbents for gallic acid in aqueous solution. The prepared adsorbents have a high specific surface area (347-563 m2 g-1), better pore development for samples treated with alkali metal chlorides than with mineral acids and are more acidic than the initial xerogel (p.z.c range 2.49-6.87 vs. 7.20). The adsorption properties of the commercial xerogel improved over a wide range of pH and temperature. The experimental results indicate that the adsorption process is thermodynamically favored.

The combustion of fuel oil releases sulfur compounds, which react to form sulfur oxides that are harmful to the environment and pose a threat to human health. To mitigate these negative effects, it is crucial to pretreat fuel oil through desulfurization processes. One promising approach involves the use of deep eutectic solvents (DESs), carbon nanotubes (CNTs), and their composites (DESs/CNTs) to effectively reduce sulfur content in fuel oil.However, the conventional methods of DES-based extraction desulfurization and CNT-based adsorption desulfurization suffer from low desulfurization rates. Additionally, the composite material DESs/CNTs is in a semi-solidified form, resulting in high viscosity, complex operation procedures, and increased waste and environmental pollution. To address these challenges, this study focused on the preparation of CNTs/PEG-PVA hydrogel. This hydrogel not only maintains the high desulfurization rate observed in the DESs/CNTs composite material but also possesses several advantages. Firstly, it is convenient to use, offering ease of handling and application. Secondly, it is biodegradable, meaning it can break down naturally over time, reducing its impact on the environment. Lastly, the hydrogel is reusable, allowing for repeated use, thereby minimizing material waste. The desulfurization rate achieved with the CNTs/PEG-PVA hydrogel is remarkably high, reaching up to 99.8%. Moreover, the material utilization rate is close to 100%, meaning that almost all of the hydrogel is utilized in the desulfurization process, reducing unnecessary material consumption. In summary, the innovative CNTs/PEG-PVA hydrogel presents a highly efficient and environmentally friendly solution for desulfurization in fuel oil. Its superior desulfurization rate, alongside its convenience, biodegradability, and reusability, positions it as a promising alternative that not only ensures effective desulfurization but also contributes to sustainable practices in the energy industry.

Carbon monoxide (CO) concentrations in wildfire plumes are easily measured from satellites. This gas can be used as a proxy for carbon dioxide. Forest fires play an important role in the carbon balance and in particular the CO balance. The most likely causes of mega-fires of 2003, 2012, 2021, and 2023 in the Northern hemisphere are heat waves and severe droughts associated with changes in general circulation. Here we analyze satellite data obtained by two different sounders, AIRS and TROPOMI. Different sensitivity to the lowest troposphere allows obtaining information about anthropogenic or pyrogenic contamination of the boundary layer. Shapes of areas polluted by mega-fires in 2019-2020 (Southeastern Australia) and 2021 (Central Siberia) coincide with the areas occupied by coal deposits. The Siberian Lena and Tunguska coal basins are the two largest coal fields in the world. In 2021, their combined area accounted for 90% of fire CO emission from the entire Russian Federation. So strong fires have not observed in this area before. Under- and sub-ground coal combustion may be included into the list of wildfire fuels, at least their role for ignition should be admitted. Further research is needed to assess the importance of coal fires to global climate.

Excessive nitrogen application has become a hidden danger threatening the sustainable development of agriculture. Exploring the potential genes will help to improve the nitrogen availability of wheat through molecular breeding. We therefore conducted wheat transcriptomics and proteomics researches under complete culture medium without nitrogen (N0) and complete culture medium with nitrogen (N1). The results showed that, the nitrogen deficit decreased the fresh weight, N content and net photosynthetic rate of winter wheat. 3949 and 2675 differentially expressed genes (DEGs) were identified in the shoot and root, respectively, while 164 and 129 differentially expressed proteins (DEPs) were identified in the shoot and root respectively. 9 genes in shoot and 26 genes in root showed the same trends in RNA and protein levels. 5 genes in shoot and 4 genes in root showed the opposite trends in RNA and protein levels. Pathway enrichment of wheat transcriptome and proteome under nitrogen deficit proposed 3 candidate genes related to photosynthesis in shoot, 4 candidate genes related to carbon metabolism in shoot, and 12 candidate genes related to carbon metabolism in root. Meanwhile, the chromosomal and subcellular localization of these genes were listed, which will provide reference for improving nitrogen availability through molecular breeding.

A study on the dependence of the thermal conductivity of the percolation network of carbon nanotubes (or CNTs) on the type and degree of functionalization has been carried out. The study was focused on the influence of the more commonly used -COOH, -OH and -СОNH2 groups. A non-linear dependence of the conductivity on the number of functional groups has been revealed. A small number of functional groups can improve conductivity, and a large one can impair it. We presuppose the existence of competing processes that increase thermal conductivity (changes in the CNT geometry, improvement of the contact between them) and enhance photon scattering (emergence of defects and scattering centers). The data can be used for controlling the thermophysical properties of the CNTs as well as determining the optimal degree of functionalization during the development of composites and nanodevices.

Adopting banana peel as raw material, the adsorption properties of banana peel hydrothermal carbon modified with KOH solution for lead ions in aqueous solution were studied. The surface structure and functional groups of the modified hydrothermal carbon were analyzed by XRD and SEM. The results showed that the banana peel hydrothermal carbon prepared from 0.5 mol/L KOH solution had large pores, and its adsorption capacity reached 42.92 mg/g at a pH value of 6; When the concentration of KOH solution is 0.5 mol/L, the solid liquid ratio is 2 g/L, the adsorption capacity reaches 21.39 mg/g, and the adsorption rate reaches 82.74%; When the concentration of lead solution increased to 100 mg/L, the adsorption capacity of modified hydrothermal carbon for lead ions decreased to 78.26%; The equilibrium adsorption time of lead ion in solution on phosphoric acid modified hydrothermal carbon from banana peel was 250 minutes, and the adsorption process met the quasi second order kinetic model and Freundlich isotherm equation, with an equilibrium adsorption rate of 88.62%. The adsorption of lead ions in solution by KOH modified hydrothermal carbon is mainly chemical physical adsorption.

Using banana peel as raw material, the adsorption properties of hydrothermal carbon pre-10 pared from banana peel modified with different concentrations of phosphoric acid solution for lead 11 ions in aqueous solution were studied. The surface structure and functional groups of the modified 12 hydrothermal carbon were analyzed by XRD and SEM. The results show that the surface of the 13 modified banana peel hydrothermal carbon prepared at 240℃ and 2mol/L phosphoric acid solution 14 has large pores. The adsorption capacity is larger when pH value is 6.When the concentration of 15 phosphoric acid solution was 2mol/L, the solid-liquid ratio was 2g/L, the adsorption capacity was 16 40.64mg/g, and the removal rate was 82.74%.When the initial concentration of lead solution in-17 creased to 100mg/L, the adsorption capacity of modified hydrothermal carbon for lead ion increased 18 to 76.81mg/g, and the removal rate decreased to 76.81%.The equilibrium adsorption time of banana 19 peel phosphoric acid modified hydrothermal carbon for lead ions in solution is 300min. The adsorp-20 tion process satisfies the pseudo-second-order kinetic model and Langmuir isotherm equation. The 21 reaction temperature is 313K, and the equilibrium adsorption capacity can reach 101.19mg/g. The 22 adsorption of Pb ions in aqueous solution by phosphoric acid modified hydrothermal carbon is 23 dominated by single layer chemisorption. The artificial neural network has a fitting correlation of 24 0.99, and the adsorption process includes physical adsorption, electrostatic attraction, ion exchange, 25 and surface complexation.

This manuscript explores sustainable agriculture's role in mitigating environmental challenges and meeting the nutritional needs of a growing global population. The objective is to assess the impact of different fertilizers on two distinct tomato-growing soils, each characterized by unique chemical and biological properties. The study compares four fertilizer treatments: Additionally, it evaluates the environmental implications of these fertilizers, focusing on their Carbon and Water Footprints. The findings indicate significant improvements in soil quality with SBO fertilizer. Both soils experienced a shift towards a near-neutral pH, increased organic matter content, and heightened microbial biomass. Enzyme activities were notably superior in SBO-treated soils. Life Cycle Assessment (LCA) results demonstrate that the SBO-based system is the most sustainable, with the lowest Carbon footprint. NPK exerts the highest environmental impact. The Water Footprint analysis aligns with these results, showing that SBO requires the least water for tomato production. In summary, this study underscores the significance of sustainable fertilization practices in improving soil quality and reducing environmental footprints in agriculture, offering potential benefits for food production and environmental conservation.

Polymers' controlled pyrolysis is an economical and environmentally friendly solution to prepare activated carbon. However, due to the experimental difficulty in measuring the dependence between tissues and pyrolysis parameters at high temperatures, the unknown pyrolysis mechanism hinders access to the target products with desirable morphologies and performances. In this study, we investigate the pyrolysis process of polystyrene under different heating rates and temperatures employing reactive molecular dynamics (ReaxFF-MD) simulations. A clear profile of the generation of pyrolysis products determined by the temperature and heating rate is constructed. It is found that the heating rate affects the type and amount of pyrolysis intermediates and their timing, and low-rate heating helps yield more diverse pyrolysis intermediates. While the temperature affects the pyrolytic tissues of the final equilibrium products, either too low or too high a target temperature is detrimental to generating large areas of graphitized tissue. The established theoretical evolution process matches experiments well, thus contributing to preparing target activated carbons by referring to the regulatory mechanism of pyrolytic tissues.

Demand for nutmeg essential oil in Indonesia and the world is increasing. Nutmeg essential oil is obtained from young nutmeg seeds extracted by water steam distillation (WSD). The weakness of the extraction process with WSD is the long distillation time (24 hours), wasteful of fuel, wasteful of manpower, produces polluting gases which damage the environment and requires a lot of water as a coolant. The purpose of this study was to compare the WSD and SCFE methods for extracting nutmeg essential oil. The research was conducted by extracting nutmeg essential oil using two methods are WSD and SCFE. The results showed that the chemical composition of the nutmeg essential oil produced by the two methods was almost similar. Nutmeg essential oil produced by both methods shows the same characterization. The yield between the two methods is almost the same, in the range of 10-12% using extraction time 15-60 minutes. The SCFE method has advantages over WSD are a faster extraction time, does not require heating materials and CO2 gas can be reused. In conclusion, SCFE is an alternative method to increase the production of nutmeg oil.

The El Niño-Southern Oscillation (ENSO) stands as the paramount tropical phenomenon of climatic magnitude resulting from ocean-atmosphere interaction. Due to its atmospheric teleconnection mechanism, ENSO wields influence over diverse environmental variables spanning distinct atmospheric scales, thereby potentially impacting the spatiotemporal distribution of atmospheric aerosols. Within this framework, this study aims to appraise the relationship between ENSO and atmospheric aerosols across the Legal Amazon during the period between 2006 and 2011. Over this quinquennium, four ENSO events were identified. Concurrently, an analysis was conducted on the spatiotemporal variability of aerosol optical depth (AOD) and AOD extinction for Black Carbon (EAOD-BC), concomitant with said ENSO events, utilizing data derived from the Aerosol Robotic Network (AERONET), MERRA-2 model, and ERSSTV5. Through the Windowed Cross Correlation (WCC) approach, statistically significant phase lags of up to 4 to 6 months were observed between ENSO indicators and atmospheric aerosols. Moreover, conspicuous increases of over 100% in atmospheric aerosol concentration were evidenced subsequent to El Niño periods, especially during the intervals encompassing the La Niña phase, particularly within the La Niña CP (Central Pacific)/Modoki category. By analyzing specific humidity anomalies (QA), exceptional scenarios in the region were detectable. This observation suggests a notable singularity when juxtaposed with antecedent investigations and typical average patterns characterizing the impacts on the Amazonian region.

We report on a new form of nanoscale carbon nitride in the shape of single layer half dome structures grown on the step edges of boron nitride sheets. The half dome structure grown on the step edges of boron nitride sheets. The half dome structures are formed spontaneously at high temperature using Iron oxide nanoparticles capped with tetremethylammonium hydroxide supported on BN sheets. During the combustion process the support, firstly, acted as a reducing agent, secondly, as a source of nitrogen that permitted the transformation of the organic capping agent in sp1 CN chains linked with sp2 CN domains. During the Ostwald ripening process smaller nanoparticles migrates towards bigger nanoparticles, when the nanoparticles come across the step edges of few layer boron nitride sheets the half dome structure is formed. This new method of synthesis has demonstrated for the first time the formation of half dome structures containing cyanopolyynes sp1 chains and sp2 carbon nitride domains.

Four different Mn and Re catalysts for electrochemical CO2 reduction have been studied by IR spectroelectrochemistry (SEC) in dry acetonitrile. In the case of Mn(apbpy)(CO)3Br (apbpy= 4(4-aminophenyl)-2,2’-bipyridine) SEC suggests that a very slow catalytic reduction of CO2 occurs in acetonitrile also in the absence of proton donors, but at rather negative potentials. On the contrary, the corresponding Re(apbpy)(CO)3Br clearly displays a slow catalytic conversion already at the first reduction potential. Switching to saturated CO2 solutions in a mixture of acetonitrile and 5% of water as proton donor, the SEC of Mn(apbpy)(CO)3Br displays faster catalytic behavior.

Digital technology makes energy systems more dynamic, efficient, reliable and sustainable. Promoting the digital governance of renewable energy is not only a key part of energy transformation, but also an important initiative to cope with the global energy crisis, which provides a new impetus for realizing the goal of net-zero emissions. In order to achieve the "dual-carbon" goal, China has been actively promoting energy reform and enhancing the wide application of digital technologies in the development and utilization of renewable energy. The digital governance system and governance capacity of renewable energy is an important support for the modernization of the national governance system and governance capacity. Although the digital governance of renewable energy in China has better policy support and advantages, the dilemmas it faces are still relatively prominent, including unsound laws and policies, insufficient governance capacity, and security loopholes in digital technology, etc. Therefore, this paper proposes a problem-oriented approach to the digital governance of renewable energy. Therefore, this paper puts forward problem-oriented optimization suggestions to innovate the legal system of renewable energy digital governance, promote the digital transformation of China's renewable energy industry, provide development space for renewable energy digital governance in a diversified mode, and enhance the digital governance capacity by improving the renewable energy security system.

Recently, the difficulties in recycling and environmental pollution caused by metal-based electrode materials have limited the further development of batteries. Therefore, biomass carbon materials, with their environmental friendliness and stable performance, are the key to solving this problem. Many advances have been achieved by researchers for the application of biomass porous carbon materials in batteries. Nevertheless, the same biomass carbon materials in batteries face problems such as low utilization, low yield, and a cumbersome preparation process. This paper thus aims to summarize the recent progress of biomass carbon materials in the field of batteries and provide a detailed description of the battery performance of biomass carbon materials from three perspectives: synthesis, structure and application of carbon materials. We believe that biomass carbon composites are in line with future development and have a broad application prospect. Finally, we will give our in-depth prospect on developing biomass carbon materials.

In this paper, MnO2 nanowire (MnO2-NW) modified carbon paper (CP) electrode was developed as a novel electrochemical sensor for sensitive determination of tetrabromobisphenol A (TBBPA). MnO2 nanowire was prepared by a hydrothermal synthesis method, and the morphology and structure of MnO2 were characterized using scanning electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. Electrochemical performance of TBBPA on MnO2-NW/CP was investigated by cyclic voltammetry, and the result confirmed that MnO2-NW/CP exhibited excellent sensitive for the determination of TBBPA due to the high specific surface area and good electrical conductivity of the nanowire-like MnO2. Moreover, the important electrochemical factors such as pH value, incubation time and modified material proportion were systematically studied to improve the determination sensitivity. The interferences from similar structure compounds on TBBPA have also been investigated. Under the optimal conditions, MnO2-NW/CP displayed the linear range of 70 500 nM for TBBPA with the detection limit of 3.1 nM, which was superior to some electrochemical methods in references. The work presents a novel and simple method for the determination of TBBPA.

In this research, the adsorption of gallium onto natural zeolite (clinoptilolite) and two mesoporous activated carbons was compared and evaluated. The clinoptilolite was treated with HCl (HCPL) while mesoporous activated carbons (MCSG60A and MCO1) were synthesized by replica method, using sucrose as carbon precursor and silica gel as template. These carbonacenous materials showed large pore sizes and mesoporous surface, as well as a suitable surface chemistry for cation adsorption, which promotes a high negative charge density. On the other hand, zeolites have narrower pore sizes, which hinders the material diffusion inside the particle; however, its strength is their ion exchange capacity. Regarding the gallium kinetic studies, it is described by Pseudo-second order model for both sorts of adsorbents. MCO1 is the best carbonaceous adsorbent studied, with a capacity of 4.58 mg/g. As for zeolites, between the two zeolites studied, HCPL showed the best results, with a gallium adsorption capacity of 3.1 mg/g. The gallium adsorption mechanism onto MCO1 material is based on physisorption while HCPL is mainly retained due to an ion-exchange process. Regarding Giles classification, MCO1 isotherm described an H-4 pattern of high affinity, characteristic of multilayer adsorption. Double-Langmuir model fits properly these experimental results. In the case of zeolites, HCPL adsorption isotherm followed an L-2 pattern, typical of monolayer adsorption, being the Sips model the one which better describes the adsorption of gallium onto the zeolite.

Developing advanced carbon materials by utilizing biomass waste has attracted much attention. Herein, a N-doped carbon material (RSM-0.33-550) was prepared by directly pyrolyzing reed straw and melamine. The as-prepared RSM-0.33-550 possessed a N content of 6.02% and a specific surface area of 547.1 m2 g-1. As the anode for supercapacitors (SCs), in 6 M KOH, such RSM-0.33-550 exhibited a capacitance of 202.8 F g-1 at a current density of 1 A g-1. At a high current density of 20 A g-1, it still remained a capacitance of 158 F g-1. Notably, it delivered an excellent stability with capacity retention of 96.3% at 20 A g-1 after 5000 cycles. This work not only offer a new electrode material for SCs, but also gives a new insight for rationally utilizing the biomass waste for energy storage.

Along with the rapid development of technology and industry, the need for energy storage has become fundamental. One promising energy storage devices is the supercapacitor. Several type supercapacitors are available, one of which is the electrical double-layer capacitor made from carbon graphite and multiwalled carbon nanotubes (MWCNTs). In this study, we combined these two materials into a working electrode in a three-electrode system. In the morphological analysis using scanning electron microscope, transmission electron microscope, and X-ray diffraction, the two materials were found to have formed a composite on the surface. In the electrochemical analysis, two types of testing were conducted using cyclic voltammetry and electrochemical impedance spectroscopy. Electrochemical analysis was carried out on five electrolyte concentrations of Na2SO4 from 1 to 6 M. The capacitance produced at concentrations of 1, 2, 3, 4, and 5 M were 34.395, 35.808, 46.284, 49.502, and 76.815 F/g, respectively. At an electrolyte concentration of 5 M Na2SO4, an energy density of 27.312 Wh/Kg and a power density of 343.786 W/Kg were produced. Meanwhile on concentration of 6 M, the surface of the electrode was damaged.

The research results conducted on binderless tungsten carbide (WC) ceramics obtained by Spark Plasma Sintering (SPS) of WC powders with different average particle sizes (0.095, 0.8, 3 μm) are presented. Nonuniform distribution of crystalline phases and microstructure of the WC ceramics was studied using layer-by-layer XRD analysis and SEM. Surface layers of the WC-based ceramics are characterized by nonuniform distribution of W2C crystalline phase and grain sizes, including the appearance of abnormally large grains. Thickness of the nonuniform layer was at least 50 μm. The effect under study is associated with an intense carbon diffusion from graphite foil. On the one hand, this contributed to a decrease in the intensity of W2C phase particle formation, which is transformed into α-WC phase due to the carbon. On the other hand, it caused abnormal grain growth in the layer where the carbon diffused. The obtained value of the carbon diffusion depth exceeds the values known from the literature (up to 1 μm in the case of volume diffusion even at temperature of 2370℃ and exposure time of ~ 60 h). The use of boron nitride (BN) as a protective coating on graphite mold parts did not prevent the formation of nonuniform layer on the ceramic surface.

The use of allometric tools allows estimating the biomass of a plant species with greater precision. Tree roots are the least studied part of the vegetation due to the difficulty in obtaining complete root systems. For this reason, the objective was to generate an allometric model to estimate the amount of biomass accumulated in the root system of Abies religiosa trees in El Chico National Park, Hidalgo. For this purpose, 61 trees of A. religiosa were extracted from 0.06 to 3.56 m in height, using a backpack sprayer of pressurized water that detached the soil from the root. The response variable was root fresh weight and the independent variables were height, diameter and age+1, according to the fit of the models tested. Diameter was the variable with the best fit (r2 = 0.95 ± 0.04), obtaining the following equation PFR = (20.918 + D (2.4475)). The allometric model accurately estimates the below-ground biomass contained in the roots, which will allow us to obtain the complete biomass of an A. religiosa forest by having access to data on both the aerial and root components.

Enhancement in chemisorption is one of the active research areas in carbon materials. To remedy the thermally degraded chemisorption at high temperatures, we report a comprehensive study of kink structures in free-standing monoatomic carbon nanowires upon heating. Our Monte Carlo simulation considers multi-monoatomic carbon chains laterally interacted by the Van der Waals force. Our study reveals that the carbon nanowires maintain their linearity regardless of chain length at low temperatures, but this is not the case at high temperatures. Disordered kink structure is observed in the short carbon chains, especially above the Peierls transition temperature. The severe kink structure might increase the possibility of attaching negatively charged atoms, thereby contributing to the development of next-generation materials for chemisorption at high temperatures. We have also provided an important inspection that any physical property of the finite-length carbon chain predicted by ab-initio calculation should reconsider the atomic rearrangement due to the thermal instability at high temperatures.

Carbon, which exists in large quantities on Earth, is a material with interesting properties, and many studies have been conducted since the past. In particular, nano-sized carbon allotropes are called carbon nanomaterials, and many studies are currently underway. Among them, carbon nanowall (CNW) is a structure in which graphene of sp2 bond is grown vertically, CNW have outstanding strength, can be highly electrically conducting or semiconducting, have a large specific surface area per unit mass. Electrical, chemical, physical properties of these CNW is modified by parameter such as surface density, height and thickness of it. Those have great effect on CNW and can be adjusted as growth interlayer. It was confirmed that the molybdenum disulfide (MoS2) interlayer synthesized by radio frequency (RF) magnetron sputtering altered the morphological characteristics such as the shaped edge of the CNW, the pores diameter and density. Through these studies, we confirmed the effect of MoS2 on the morphological characteristics of CNW. This opens the door to improving the performance of electrodes and devices.

We present a simple strategy to generate a family of carbon dot/iron oxide nanoparticles (C/Fe-NPs) that relies on the thermal decomposition of iron (III) acetylacetonate in the presence of a highly fluorescent carbon-rich precursor, while polyethylene glycol serves as the passivation agent. By varying the molar ratio of the reactants, a series of C/Fe-NPs have been synthesized with tuneable elemental composition in terms of C, H, O, N, Fe. The quantum yield is enhanced from 6% to 9% as the carbon content increases from 27% to 36%, while the room temperature saturation magnetization is improved from 4.1 emu/g to 17.7 emu/g as the iron content is enriched from 17 to 31%. In addition, the C/Fe-NPs show excellent antimicrobial properties, minimal cytotoxicity and demonstrate promising bioimaging capabilities, thus showing great potential for the development of advanced diagnostic tools.

The current Global Climate Change, the 2030 Agenda and the Planetary boundaries have driven new development strategies, such as the circular economy, bioeconomy and biorefineries. In this framework, this study analyzes the potential availability and sustainability of the wood supply chain for a small-scale biorefinery aiming at producing 280–300 L of bioethanol per ton dry biomass, consuming 30,000 t of dry biomass per year harvested in a 50 km radius. This wood production goal was assessed from Eucalyptus grandis stands planted for solid wood in northeastern Uruguay. Moreover, to understand the environmental performance of this biomass supply chain, the energy return on investment (EROI), carbon footprint (CF) and potential soil erosion were also assessed. The results showed that the potential wood production would supply an average of 81,800 t of dry mass per year, maintaining the soil erosion below the upper threshold recommended, an EROI of 2.3 and annual CF of 1.22 kg CO_2-eq m^–3 (2.6 g CO_2-eq MJ^–1). Combined with the environmental performance of the bioethanol biorefinery facility, these results would show acceptable values of sustainability according to EU Directive 2009/28/ec because the bioethanol CF becomes 1.7% of this petrol’s CF.

Nanostructured carriers have been widely used in pharmaceutical formulations for dermatological treatment. They offer targeted drug delivery, sustained release, improved biostability, and low toxicity, usually presenting advantages over conventional formulations. Due to its large surface area, small size and photothermal properties, graphene oxide (GO) has the potential to be used for such applications. Nanographene oxide (GOn) presented average sizes of 197.6 ± 11.8 nm, and a surface charge of -39.4 ± 1.8 mV, being stable in water for over 6 months. 55.5 % of the mass of GOn dispersion (at a concentration of 1 mg mL-1) permeated the skin after 6 h of exposure. GOn dispersions have been shown to absorb near-infrared radiation, reaching temperatures up to 45.7 °C, within mild photothermal therapy temperature range. Furthermore, GOn in amounts superior to those which could permeate the skin were shown not to affect human skin fibroblasts (HFF-1) morphology or viability, after 24 h of incubation. Due to its large size, no skin permeation was observed for graphite particles in aqueous dispersions stabilized with Pluronic P-123 (Gt-P-123). Altogether, for the first time, GOn potential as a topic administration agent and for delivery of photothermal therapy has been demonstrated.

High alkalinity values on the seaside can influence the exchange of carbon dioxide between seawater and the atmosphere. Still, there are many uncertainties about biogeochemical processes responsible for alkalinity generation in the coastal area. One example of coastal areas with high alkalinity is the German Bight. The German Bight is the south-east part of the North Sea. The literature suggests that high summer alkalinity values in the German Bight result from the exchange of the German Bight with the Wadden Sea (an intertidal zone along Dutch, German, and Danish coasts). We show that the origin of high alkalinity values in the German Bight can be sulfate reduction in sediments of the Wadden Sea and that it can increase alkalinity from March to August up to approximately 220 micromoles per liter. Also, we show that sulfate reduction does not cause any significant year alkalinity flux from the Wadden Sea to the German Bight; instead, nitrogen compounds ( and ) are responsible for it and cause an alkalinity flux about 13 GM a year from the Wadden Sea to the German Bight.

In the last 10 years, carbon dots (CDs) synthesized from renewable organic resources have been gathered a considerable amount of attention in different fields for their peculiar photoluminescent properties. Moreover, the synthesis of CDs fully responds to the principles of the circular chemistry and the concept of safe-by-design. This review will focus on the different strategies for the incorporation of CDs in organic light-emitting devices (OLEDs) and on the study of the impact of CDs properties on the OLEDs performance. The main current research outcomes and highlights are summarized to guide users towards the fully exploitation of use these materials in optoelectronic applications.

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO2-coated and Fe2O3-coated carbon fibers were used as the cathode and the anode materials, respectively. FE-SEM analysis confirmed that the CoMnO2-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amounts of ammonium persulfate (APS) as an oxidizing agent, and Fe2O3-coated carbon fiber electrode showed a uniform distribution of porous Fe2O3 nanorods over the surface of carbon fibers. The nanostructured CoMnO2 were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatments. In particular, the electrochemical properties of the CoMnO2-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g-1 at 0.7 A g-1 and good rate capability of 34.8% at 4.9 A g-1. Moreover, the wire-type device displayed the superior energy density of 60.16 Wh kg-1 at a power density of 490 W kg-1 and excellent capacitance retention of 95% up to 3,000 charge/discharge cycles.

The role of Black Carbon (BC) as a contributor to glacial retreat is of particular interest to the scientific community and decision makers, due to its impact on snow albedo and glacier melt. In this study, a thermal-optical instrument (LAHM) was used to measure effective Black Carbon (eBC) in a series of surface snow samples collected from the Vallunaraju glacier, Cordillera Blanca, between April 2019 and May 2020. The time series obtained indicates a marked seasonal variability of eBC with maximum concentrations during the dry season and dramatic decrease during the wet season. The concentrations detected ranged between a minimum of 3.73 ng/g and 4.23 ng/g during the wet season and a maximum of 214.13 ng/g and 181.60 ng/g during the dry season, in the accumulation and ablation zone. Using SNICAR model, the reduction of albedo was estimated at 6.36% and 6.60% during the dry season and 0.68% and 0.95% during the wet season, which represents an average radiative forcing of 4.52 ± 1.84 W/m2 and 4.69 ± 1.59 W/m2 in the accumulation zone, and 0.49 ± 0.27 W/m2 and 0.68 ± 0.43 W/m2 in the ablation zone. The melting of snow due to the eBC translates into 80.18 ± 37.30 kg/m2 and 83.16 ± 32.75 kg/m2 during the dry season, and 7.91 ± 4.29 kg/m2 and 10.85 ± 6.62 kg/m2 during the wet season, in the accumulation and ablation zones, respectively. Finally, the HYSPLIT trajectory assessment shows that aerosols predominate in the Amazon rainforest, especially when forest fires are most abundant according to VIIRS images.

The non-secular anomalies in carbon dioxide measurements at Mauna Loa are compared to the non-secular anomalies in the HadCRUT4 median global temperature from 1991 to 2020. A strong and significant Pearson's product-moment correlation is found between carbon dioxide anomalies and global temperature anomaly, indicating that the correlation is an actual characteristic of the atmosphere. But more important from a numerical weather prediction perspective, this result indicates that carbon dioxide anomalies can have no skills as temperature precursors on short time scales.

Since the 1960s Rare earths (REs) applications gradually have expanded to everyday life. REs have great strategic importance in industrial and technological development, so it is expected an increase in their demand. Among the REs the European Commission considered Cerium and Lanthanum as critical raw materials. This research article studies the adsorption of Ce and La onto two carbon nanomaterials, multiwalled carbon nanotubes (MWCNT) and carboxylic functionalized multiwalled carbon nanotubes (MWCNT_ox). The latter has slightly more affinity for REs than MWCNT. The recovery percentage for Ce were 89 and 98% and in the case of for La were 99 and 92% using 0.8 g of MWCNT and 0.2 g of MWCNT_ox respectively. The adsorption process fits a pseudo second-order kinetic model and the Langmuir isotherm best represented the metal uptake.

Due to low working temperature, high energy density and low pollution, proton exchange fuel cells have been investigated under different operating conditions in different applications. Using platinum catalysts in methanol fuel cells leads to increasing the cost of this kind of fuel cell which is considered as a barrier to the commercialism of this technology. For this reason, a lot of efforts have been made to reduce the loading of the catalyst required on different supports. In this study, carbon black (CB) and carbon nanotubes (CNT) have been used as catalyst supports of the fuel cell as well as using the double-metal combination of platinum-ruthenium (PtRu) as anode electrode catalyst and platinum (Pt) as cathode electrode catalyst. The performance of these two types of electro-catalyst in the oxidation reaction of methanol has been compared based on electrochemical tests. Results showed that the carbon nanotubes increase the performance of the micro-fuel cell by 37% at maximum power density, compared to the carbon black. Based on thee-electrode tests of chronoamperometry and voltammetry, it was found that the oxidation onset potential of methanol for CNT has been around 20% less than CB, leading to the kinetic improvement of the oxidation reaction. The current density of methanol oxidation reaction increased up to 62% in CNT sample compared to CB supported one, therefore the active electrochemical surface area of the catalyst has been increased up to 90% by using CNT compared to CB which shows the significant rise of the electrocatalytic activity in CNT supported catalyst. Moreover, the resistance of the CNT supported sample to poisonous intermediate species has been found 3% more than CB supported one. According to the chronoamperometry test results, it was concluded that the performance and sustainability of the CNT electro-catalyst show remarkable improvement compared to CB electro-catalyst in the long term.

This paper describes the physico-chemical study of the adsorption of dysprosium (Dy³⁺) in aqueous solution onto two types of activated carbons synthesized from spent coffee ground. KOH activated carbon is a microporous material with a specific BET surface area of 2330 m²·g^-1 and pores with a diameter of 3.2 nm. Carbon activated with water vapor and N₂ is a solid mesoporous, with pores of 5.7 nm in diameter and a specific surface of 982 m²·g^-1. A significant dependence of the adsorption capacity on the solution pH was found, while it does not depend significantly neither on the dysprosium concentration nor on the temperature. A maximum adsorption capacity of 31.26 mg·g^-1 and 33.52 mg·g^-1 for the chemically and physically activated carbons, respectively, were found. In both cases, the results obtained from adsorption isotherms and kinetic study were better fit to a Langmuir model and a pseudo-second-order kinetics. In addition, thermodynamic results indicate that dysprosium adsorption onto both activated carbons is an exothermic, spontaneous and favorable process.

This study surveyed the variation in Perfluorinated Compounds (PFCs) concentration entering urban wastewater treatment plants and proposed an optimal PFCS treatment method. The PFCS concentration in influent was shown to be affected by the types of industries and operating rate. The concentration of PFCs in the wastewater treatment effluent was slightly lower than that of influent. Thus, PFCs were considered to have barely been removed by the existing biological treatments. The pilot test result showed that about 10% of PFCs were removed by coagulation and precipitation, and the ozone and chlorine test also showed that few PFCs were removed regardless of the amount of injection. The activated carbon adsorption test showed that the removal was significantly increased by the empty bed contact time, with about a 60% removal in five minutes and over a 90% removal in 15 minutes. Therefore it is determined that a more stable and higher PFCs removal would result from the continuous oxidation processes such as ozone and adsorption processes such as activated carbon rather than a single biological treatment.

The paper describes preliminary studies on the influence of humidity on the electrical resistance of a textile sensor made of carbon fibers. The concept of the sensor refers to externally bonded fiber reinforcement commonly used to strengthen building structures. However, the zig-zag arrangement of carbon fiber tow allows measuring strains, as it is done in popular resistive strain gauges. The sensor tests proved its effectiveness in the measurement of strains, but also showed a high sensitivity to changes in the temperature and humidity which unfavorably affects the readings and their interpretation. The influence of these factors must be compensated. Due to the size of the sensor, there is not possible electrical compensation by the combining of several sensors into the half or full Wheatstone bridge circuit. Only mathematical compensation based on known humidity resistance functions is possible. The described research is the first step to develop such relations. The tests were carried out at temperatures of 10 °C, 20 °C and 30 °C, with changing the humidity in the range of 30-90%.

A overview on application of CO2 in the ironmaking and steelmaking process is presented. Study on resource utilization of CO2 is significant for the reduction of CO2 emissions and the coping with global warming. The paper introduces the research progress of CO2 utilization in the sintering, Blast Furnace, Converter, secondary refining, Continuous Casting and smelting process of stainless steel in recent years in China. According to the foreign and domestic research and application status, the paper analyzes the feasibility and metallurgical effects of the CO2 utilization in the ferrous metallurgy process. The paper mainly introduces such new techniques as 1) flue gas circulating sintering, 2) blowing CO2 through Blast Furnace tuyere and CO2 as a pulverized coal carrier gas, 3) top and bottom blowing CO2 in the converter, 4) Ladle Furnace and Electric Arc Furnace bottom blowing CO2, 5) CO2 as Continuous Casting shielding gas, 6) CO2 for stainless steel smelting, and 7) CO2 circulation combustion. CO2 has a very wide application prospect in ferrous metallurgy process and the quantity of CO2 utilization is expected to be 100kg per ton of steel. It will effectively facilitate the progress of metallurgical technology and strongly promote the energy conservation of metallurgical industry.

The Global Carbon Budget is the cumulative carbon emissions that human activities can generate while limiting the global temperature increase to less than 2°C. On this basis, most countries ratified the Paris Agreement 2015, pledging to reduce national emissions and the impacts of climate change. The European Union has planned to reduce emissions by 80% of their 1990 value by 2050 but such a target needs to be coupled with a further constraint on the cumulative greenhouse gases released along the path to 2050. The aim and the novelty of this study are to propose, for the first time, a carbon budget for the European Union, which represents the most significant physical characteristic to assess the feasibility of current EU-28 greenhouse gas reduction objectives under the goals of the 2015 Paris treaty

Development of carbon nanomaterials for adsorption thus removal of organic pollutants from water is a progressive research subject. In this regard, carbon nanomaterials with bifunctionality towards polar and non-polar or even amphiphilic undesired materials is indeed attractive for further study and implementation. Here, we created carbon buckypaper adsorbents comprising amphiphilic (oxygenated amorphous carbon (a-COx)/graphite (G)) nanofilaments that can dynamically adsorb organic biomolecules (i.e. urease enzyme) and thus purify the wastewaters of relevant industries. Given the dynamic conditions of the test, the adsorbent was highly efficient in adsorption of the enzyme (88%) while permeable to water (2382 L.h-1.m-2), thus holds a great promise for further development and upscaling. A subsequent citric acid functionalization declined selectivity of the membrane to urease, implying the biomolecules adsorb mostly via graphitic domains rather than oxidized, polar amorphous carbon ones. The devised platform i.e. the urease functionalized buckypaper is optimally conductive (13 S.cm-1) and can be further employed as a biosensor. Accordingly, water treatment can be linked to biosensing via a nanostructured membrane.

This review analyzes the synthesis and characterization of biomass-derived carbons for adsorption of emerging contaminants from water. The study begins with the definition and different types of emerging contaminants more often founded in water streams and the different technologies available for their removal including adsorption. It also describes the biomass sources that could be used for the synthesis of biochars and activated carbons. The characterization of the adsorbents and the different approaches that could be employed for the study of the adsorption processes are also detailed. Finally, the work reviews in detail some studies of the literature focused on the adsorption of emerging contaminants on biochars and activated carbons synthesized from biomass precursors.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

The proper hydrogenation of Hyper-coal (HPC) using 1, 2, 3, 4-tetrahydroquinoline (THQ) was able to decrease the oxygen content and adjust the molecular structure of HPC for preparing the spinnable pitch with high softening point (SP). The spinnable pitch prepared from the THQ-soluble (QS) fraction of HPC as a precursor consisted more naphthenic carbon groups than that prepared from the 1-methylnaphthalene (1-MN) soluble (MNS) fraction of HPC. The HPC-QS derived pitch showed excellent spinnability even the SP of 260°C, and the tensile strength of the resultant carbon fiber was up to 1350 MPa with a diameter around 8 µm by only heat treatment at 800°C for 5 min.

We report a new fabrication method for a fully stretchable supercapacitor based on single wall carbon nanotube (SWCNT)-coated electrospun rubber nanofibers as stretchable supercapacitor electrodes. The deposition conditions of SWCNT on hydrophobic rubber nanofibers are experimentally optimized to induce a uniform coating of SWCNT. For surfactant-assisted coating of SWCNT, both water contact angle and sheet resistance were the lowest compared to the cases with other surface treatment methods, indicating the most effective coating approach. The excellent electromechanical properties of this electrode under the stretching condition is demonstrated by the measurement of Young’s modulus and normalized sheet resistance. This superb tolerance of the electrode with respect to stretching results from i) high aspect ratios of both nanofiber templates and the SWCNT conductors, ii) highly elastic nature of rubbery nanofiber, and iii) strong adherence of SWCNT-coated nanofiber on the elastic ecoflex substrate. Electrochemical and electromechanical measurements on the stretchable supercapacitor devices reveal that the volumetric capacitance (15.2 F cm-3 at 0.021 A cm-3) of the unstretched state is maintained for strains of up to 40 %. At this level of strain, the capacitance after 1,000 charge/discharge cycles is not significantly reduced. The high stability of our stretchable device suggests potential future applications in various types of wearable energy storage devices.

The application of graph theory in chemical and molecular structure research far exceeds people's expectations, and it has recently grown exponentially. In the molecular graph, atoms are represented by vertices and bonded by edges. Closed forms of multiplicative degree-based topological indices which are numerical parameters of the structure and determine physico-chemical properties of the concerned molecular compound. In this article, we compute and analyze many multiplicative degree-based topological indices of silicon-carbon Si₂C₃-I[p,q] and Si₂C₃-II[p,q].

Porous graphite was prepared without the use of template by rapidly heating the carbonization products from mixtures of anthracene, flourene, and pyrene with a CO₂ laser. Rapid CO₂ laser heating at a rate of 1.8 × 10 ⁶ °C/s vaporizes out the fluorene-pyrene derived pitch while annealing the anthracene coke. The resulting structure is that of graphite with 100 nm spherical pores. The graphitizablity of the porous material is the same as pure anthracene coke. Transmission electron microscopy revealed that the interface between graphitic layers and the pore walls are unimpeded. Traditional furnace annealing does not result in the porous structure as the heating rates are too slow to vaporize out the pitch, thereby illustrating the advantage of fast thermal processing. The resultant porous graphite was prelithiated and used as an anode in lithium ion capacitors. The porous graphite when lithiated had a specific capacity of 200 mAh/g at 100 mA/g. The assembled lithium ion capacitor demonstrated an energy density as high as 75 Wh/kg when cycled between 2.2 V to 4.2 V.

The assessment of biomass carbon stocks was conducted at plot scale as a sample to estimate for all vegetation areas by using destructive sampling and or allometric equation method. Remote sensing is one of the techniques can be used to estimate and mapping biomass carbon stock for the entire areas. The objectives of the study are the identification and determine the range of electromagnetic wave of Landsat 8 satellite data that most suitable for assessing and mapping biomass carbon stock distribution. This research analyses exponential regression equation between spectral radiance values (Lλi) for with biomass measurement results on the field to find the best correlation based on the coefficient of determination value (R2). It also analyses the relationship between field biomass and NDVI value (Normal Differences Vegetation Index) from satellite data. The study area consists of 54.9% bush (Bs), 24.5% scrub (Sc), 16.8% secondary forest (Sf), while the rest (3.8%) is a water body. The with average biomass carbon stock value 4.11 tons.ha-1, 64.43 tons.ha-1, and 85.36 tons.ha-1, for strata Sc, Bs, and Sf respectively. Spectral radiance of SWIR (Shortwave Infra-Red) band 6 is determined as a spectral characteristic that can be used to estimating carbon stock with following the equation Y= 12657(EXP(-0.642(Lλband6)) with r2 = 0.75. Correlation NDVI and field biomass showed the low r2 value (0.08), so in this study, NDVI cannot be used to estimate the biomass carbon stock.

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

We report on magnetic studies of inhomogeneous commercial and synthesized amorphous carbon (a-C) and a-C doped with sulfur (a-CS) powders which exhibit (i) peculiar magnetic behavior and (ii) traces of two superconducting (SC) phase ~ Tc=33 and at 65 K. (i) The temperature dependence of zero-field-cooled (ZFC) curves measured up to room temperature show a well distinguish elusive peaks around 50-80 K, their origin is not yet known. These peaks are totally washed-out in the second ZFC sweeps and in the FC branches as well. As a result, in the vicinity of the peaks, the FC curves lie below the ZFC peaks (FC<ZFC), a phenomenon which is rarely observed. These magnetic anomalies are intrinsic properties of a-C and a-CS materials (ii) SC was observed in three different a-C sources: (a) The commercial a-C powder contains 0.21% of sulfur and it is suggested that two different a-CS phases (at 33 and 65 K) are the origin of the two SC states observed. The compositions of these two phases are not yet unknown. The small SC volume fractions of the 33 K phase can be enhanced by a solid reaction with additional sulfur at 250 ºC. (b) The synthesized a-C powder (obtained from decomposition of sucrose) is not SC. However, when mixed with sulfur and heated at 400 ºC under a protective atmosphere, the a-CS powder obtained also show traces of a SC phase at TC= 42 K. (c)The same occurs in a-C thin films. The as-grown films are not SC but a SC phase at Tc = 34 K emerges after the films were reacted with sulfur at elevated temperatures. It is concluded therefore, that all SC phases observed are due to different unknown a-CS phases. Since the a-C and a-CS powders possess SC and magnetic states, we believe that these powders resemble the high TC curates and Fe-As based systems in which the SC and the magnetic states are closed related to each other.

In recent years, genetic research has been developing rapidly and taking on a larger role in research and medicine. The synthesis of any particle that can be used in this research can pave the way for new developments in this field. This research aims to develop a chemical method to produce nitrogen-doped carbon quantum dots - economical and bio-sourced substances that bind to genomic DNA. Carbon quantum dots are produced by the green synthesis hydrothermal method from radish, which is abundant in nature, and economically affordable. Nitrogen is added to increase the fluorescence properties of the produced carbon quantum dots and to improve their binding to DNA. The synthesized nitrogen-doped carbon quantum dots (N-CQDs) were tested through chromosome imaging subsequently. It was shown that N-CQDs can bind to the chromosomes, and N-CQDs reflected green light better than DAPI under the FITC filter, a potential advantage of using N-CQDs over DAPI in chromosome imaging.

A scientific carbon accounting system can help enterprises reduce carbon emissions. This study took the enterprise in the Yangtze River basin as a case study. The accounting classification of carbon emissions in the life cycle of lime production was assessed, and the composition of the sources of carbon emission was analyzed, covering mining explosives, fuel (diesel, coal), electricity and high temperature limestone decomposition. Using the IPCC emission factor method, a carbon life cycle emission accounting model for lime production was established. We determined that a total of 354,200 tons of carbon emissions were generated from producing 321,000 tons of lime in a year. The decomposition of limestone at a high temperature was the largest carbon emission source, accounting for 62.34% of the total carbon emission. Coal combustion was also an important source of carbon emissions, accounting for 32.66% of total carbon emissions. The carbon emission for one ton of activated lime was 1.46kg, 1.49kg, 1100kg and 1102.95kg respectively for the open-pit, mining stage, crushing stage, and the calcination stage. Based upon the main sources of carbon emission for lime production, carbon emission reduction should focus on CO2 capture technology, fuel optimization and energy control. Using our analysis of carbon emissions, the carbon emission factor of producing unit quicklime of the lime enterprise in the Yangtze River basin was determined. Furthermore, the research into carbon emission reduction for lime production can provide a point of reference for the promotion of carbon neutrality in the same industry.

This study aimed to evaluate the effects of plasma treated metal contaminated water, used for irrigation, on plant growth. Zinc (Zn) is one of the more commonly used metals. It can enter the environment from industrial processes as particles released into the atmosphere or as wastewater discharged into waterways or the ground. Exposure to large amounts of zinc, even for a short time, can seriously affect human health. In this experiment, three different DBD O2 plasma treated zinc contaminated water and a control (tap water) were used, with Arabidopsis thaliana as the model plant. The treatments were: i) Control, ii) Zn water, iii) Zn+O3(30 min), and iv) Zn+O3(60 min). Arabidopsis plant exhibited maximum growth in the Zn+O3(30 min) treatment. All growth parameters, except leaf area, followed this trend: Zn+O3(30 min) > Control > Zn water > Zn+O3(60 min). Gene expression analysis revealed that reduced metal ion stress and controlled oxidation due to active oxygen species contributed to favorable/improved growth of Arabidopsis in the Zn+O3(30 min) treatment. Therefore, 30 minutes of DBD O2 plasma treated zinc contaminated water [Zn+O3(30 min)] can mitigate the adverse effects of excess zinc ions and promote the growth of Arabidopsis plants.

In this study, we demonstrate the direct preparation of dihalo-γ-lactams featuring two distinct halogens from dichloroamides using a novel Atom Exchange Radical Cyclization (AERC) procedure. This method integrates the established Atom Transfer Radical Cyclization with halogen exchange in solution. The technique operates under mild conditions and requires little amounts of metallic copper, serving as both a supplemental activator and reducing agent.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.