Hardy Cross originally proposed a method for analysis of flow in networks of conduits or conductors in 1936. His method was the first really useful engineering method in the field of pipe network calculation. Only electrical analogs of hydraulic networks were used before the Hardy Cross method. A problem with the flow resistance versus the electrical resistance makes these electrical analog methods obsolete. The method by Hardy Cross is taught extensively at faculties and it still remains an important tool for analysis of looped pipe systems. Engineers today mostly use a modified Hardy Cross method which threats the whole looped network of pipes simultaneously (use of these methods without computers is practically impossible). A method from the Russian practice published during 1930s, which is similar to the Hardy Cross method, is described, too. Some notes from the life of Hardy Cross are also shown. Finally, an improved version of the Hardy Cross method, which significantly reduces number of iterations, is presented and discussed. Also we tested multi-point iterative methods which can be used as substitution for the Newton-Raphson approach used by Hardy Cross, but this approach didn’t reduce number of required iterations to reach the final balanced solution. Although, many new models have been developed since the time of Hardy Cross, main purpose of this paper is to illustrate the very beginning of modeling of gas and water pipe networks or ventilation systems.

The present study was carried out at the north-eastern part of Bangladesh to investigate organochlorine pesticide (OCP) residues and microbiological quality of dried barb (Puntius sophore). Samples were collected from both producers and retailers from December 2016 to April 2017. A control sample was also prepared with the same raw fish used by the producers in the laboratory to compare the result. Gas Chromatography with Electron Capture Detector (GC-ECD) was used to detect and quantify OCP residues. Around 22 % (6) samples out of 27 were found contaminated with OCP residues. Among these six adulterated samples, four were from retailers and two from producers. Only Aldrin was detected in four samples and rest two samples were detected with both Aldrin + Dieldrin and Aldrin + Endrin. Aldrin was found between 0.332 to 0.967 ppm, Dieldrin 0.762 ppm, and Endrin 0.828 ppm. All these values were much higher than the Maximum Residual Limit (MRL) 0.1 ppm. Aerobic Plate Count (APC) of producer samples were ranged between log5.3 ± 0.02 to log5.4 ± 0.03, log6.2 ± 0.02 to log6.4 ± 0.02 for retailer samples and log5.0 ± 0.03 to log5.2 ± 0.04 for control samples. While fungal count was ranged between log3.2 ± 0.04 to log3.5 ± 0.04, log3.4 ± 0.04 to log3.6 ± 0.03 and log2.2 ± 0.05 to log2.5 ± 0.03 for producer, retailer and control samples respectively. All the producer and retailer samples and one-third of the control samples were found contaminated with Escherichia coli. Whereas, Salmonella sp. was detected as 13.3% in producer samples, 20% in retailer samples except for the control. In case of Vibrio sp., maximum count was found for retailer samples (13.3%), whereas, producer and control samples showed no detection. The finding of the present study revealed the presence of pesticides and poor microbiological quality of dried barb are alarming for the consumers of Bangladesh and which may cause chronic disease and potential long-term risk for human health.

The conversion of C1 gas feedstock, such as carbon monoxide (CO), into useful platform chemicals has attracted considerable interest in industrial biotechnology. One conversion method is electrode-based electron transfer to microorganisms using bioelectrochemical systems (BESs). In this BES system, acetate is the predominant component of various volatile fatty acids (VFAs). To appropriately separate and concentrate the produced acetate, a BES type electrodialysis cell with an anion exchange membrane was constructed and evaluated under various operational conditions, such as the applied external current. The higher acetate flux of 23.9 mmol/m2∙hr was observed under -15 mA current in an electrodialysis-based bioelectrochemical system. In addition, the initial acetate concentration affects the separation efficiency and transportation rate. The maximum flux appeared at 48.6 mmol/m2∙hr when the acetate concentration was 100mM, whereas the effect of the initial pH of the anolyte was negligible. The acetate flux was 14.9 mmol/m2∙hr when actual fermentation broth from BES based CO fermentation, was used as a catholyte. A comparison of the synthetic medium with the actual fermentation medium suggests that unknown substances and metabolites in the actual medium interfere with electrodialysis in the BES. These results provide information on the separation and optimal concentration for VFAs produced by C1 gas fermentation through electrodialysis, and a combination of a BES and electrodialysis.

Metal oxide p-n heterojunction nanofibers (NFs) are among the most promising approaches to enhancing the efficiency of gas sensors. In this paper, we report the preparation of a series of p-NiO-loaded n-ZnO NFs, namely (1 − x) ZnO-xNiO (x = 0.03, 0.05, and 0.1 wt%), for hydrogen gas sensing experiments. Samples were prepared through the electrospinning technique followed by a calcination process. The sensing experiments showed that the sample with 0.05 wt% NiO loading resulted in the highest sensing performance at an optimal sensing temperature of 200 °C. The sensing mechanism is discussed in detail and contributions of the p-n heterojunctions, metallization of ZnO and catalytic effect of NiO on the sensing enhancements of an optimized gas sensor are analyzed. This study demonstrates the possibility of fabricating high-performance H₂ sensors through the optimization of p-type metal oxide loading on the surfaces of n-type metal oxides.

Transient analysis of gas flow in pipeline was studied. Finite Element Method based on ANSYS FLOTRAN was used to account for changes in pressure, temperature and flow rate. Compressibility factor function of temperature and pressure was considered. For non-isothermal transient results, the pressure and the flowrate gave wave propagation as a result of slow transients created by demand condition at the outlet end of custody transfer. Results obtained were in agreement with the demand restrictions at the outlet end of custody transfer indicating that the predictions are accurate and reliable. The results demonstrated that the Finite Element Method gave accurate prediction of pressure, temperature and flowrate in transient gas studies. For steady state non-isothermal model, results showed that the magnitude of the average pressure drop was higher when pressure was predicted with constant compressibility factor, but the same average pressure drop was reduced when the pressure was predicted with variable compressibility factor, z. Since compressibility factor is a function of temperature and pressure, the above findings signifies that in the case when gas temperature does not stabilize, the prediction of pressure with isothermal model and constant compressibility factor will lead to significant errors.

This paper consists of the design and implementation of a simple conditioning circuit to optimize the electronic nose performance, where a temperature modulation method was applied to the heating resistor to study the sensor’s response and confirm whether they are able to make the discrimination when exposed to different volatile organic compounds (VOC’s). This study was based on determining the efficiency of the gas sensors with the aim to perform an electronic nose, improving the sensitivity, selectivity and repeatability of the measuring system, selecting the type of modulation (e.g., pulse width modulation) for the analytes detection (i.e., Moscatel wine samples (2% of alcohol) and ethyl alcohol (70%)). The results demonstrated that by using temperature modulation technique to the heating resistors, it is possible to realize the discrimination of VOC’s in fast and easy way through a chemical sensors array. Therefore, a discrimination model based on principal component analysis (PCA) was implemented to each sensor, with data responses obtaining a variance of 94.5% and accuracy of 100%.

Basaltic activity is the most common class of volcanism on Earth, characterized by magmas of sufficiently low viscosities such that bubbles can move independently of the melt. Following exsolution, spherical bubbles can then expand and/or coalesce to generate larger bubbles of spherical-cap or Taylor bubble (slug) morphologies. Puffing and strombolian explosive activity are driven by bursting of these larger bubbles at the surface. Here, we present the first combined model classification of spherical-cap and Taylor bubble driven puffing and strombolian activity modes on volcanoes. We furthermore incorporate the possibility that neighboring bubbles might coalesce, leading to elevated strombolian explosivity. The model categorizes behavior in terms of the temporal separation between the arrival of successive bubbles at the surface and bubble gas volume or length, with the output presented on visually intuitive two-dimensional plots. The categorized behavior is grouped into the following regimes: puffing from a) cap bubbles; and b) non-overpressurised Taylor bubbles; and c) Taylor bubble driven strombolian explosions; each of these regimes is further subdivided into scenarios whereby inter-bubble interaction does/doesn't occur. The model performance is corroborated using field data from Stromboli (Aeolian Islands, Italy), Etna (Sicily, Italy) and Yasur (Vanuatu), representing one of the very first studies, focused on combining high temporal resolution degassing data with fluid dynamics, as a means of deepening our understanding of the processes which drive basaltic volcanism.

Anomaly detection plays a significant role in helping gas turbines run reliably and economically. Considering collective anomalous data and both sensitivity and robustness of the anomaly detection model, a sequential symbolic anomaly detection method is proposed and applied to the gas turbine fuel system. A structural Finite State Machine is to evaluate posterior probabilities of observing symbolic sequences and most probable state sequences they may locate. Hence an estimating based model and a decoding based model are used to identify anomalies in two different ways. Experimental results indicates that these two models have both ideal performance overall, and estimating based model has a strong ability in robustness, while decoding based model has a strong ability in accuracy, particularly in a certain range of length of sequence. Therefore, the proposed method can well facilitate existing symbolic dynamic analysis based anomaly detection methods especially in gas turbine domain.

Natural Gas (NG) processing is a prominent industrial separation process. Among the available techniques, the innovative membrane process shows potential for efficient removal of impurities, including carbon dioxide (CO₂). This study focuses on utilizing breakthroughs in membrane separation to drive sustainable CO₂ extraction from natural gas. Through comprehensive research and analysis, we explore the effectiveness and feasibility of membrane-based systems in removing CO₂ impurities from NG, thus promoting greener and more sustainable industrial practices. Our findings underscore the transformative nature of membrane separation technology, presenting new possibilities for a more environmentally-friendly and sustainable approach to CO₂ extraction from natural gas.Natural Gas (NG) processing utilizes various techniques for impurity removal, with the membrane process emerging as a promising option for efficient carbon dioxide (CO₂) extraction. This research proposes the integration of a simple mathematical model into ASPEN HYSYS to design a membrane system for CO₂/CH₄ separation. The study also investigates parameter sensitivities by altering operating conditions, such as feed composition and pressure, as well as membrane properties, including selectivity. By analyzing these variables, we aim to optimize the performance and efficiency of the membrane system, facilitating the sustainable extraction of CO₂ from NG. The findings contribute to advancing the design and operation of membrane-based processes for CO₂ separation, paving the way for greener and more sustainable industrial practices. In addition, this study explores various configurations for optimizing the design of the membrane system, including single-stage with and without recycling as well as double-stage configurations. The investigation demonstrates that methane recovery can be enhanced through the recycling of the permeate stream and by implementing a double stage membrane system. These findings highlight the potential for improving the efficiency and performance of the membrane system, enabling higher methane recovery rates. By considering different configurations, this research contributes to the development of more effective and sustainable CO₂ extraction processes from natural gas.

Plug and abandonment (P&A) operations demand valuable time and resources with operational procedures and materials to establish the well barrier element. This study proposes the use of a water-based fluid as a liquid well barrier element for temporary abandonment, based on esti-mates of its lifespan and survival probability on downhole conditions acquired through acceler-ated life tests. For that, the water-based formulation was tested and exposed to 95, 110, 140 and 150°C, for time intervals ranging from 1 to 10 days. After temperature exposure, the fluid prop-erties were verified and failure was detected by accounting for any deterioration in rheological parameters and/or a substantial increase in filtrate volume. Statistical analysis of failure data was performed in R software using Weibull Model, and fluid average lifespan and survival probability were estimated for P&A temperatures. The results obtained demonstrates that the degradation of the fluid only was observed for 140 and 150°C and is mostly related to the CMC deterioration. The reliability metrics shows that until 80°C the fluid is a promising alternative for temporary abandonment, with no need of monitoring. For higher downhole temperatures, theses metrics should be considered to define the maximum time of operation and requirements for monitoring management in the operation design.

Circulating tumor cells (CTCs) are cells released from the primary tumor and intravasate into the blood or lymphatic vessels, where they are transported to distant sites and act as seeds that initiate cancer metastases. Recent advances in CTC research have shown their relevance as prognostic markers for early and metastatic disease detection, predictive biomarkers for relapse, and response to medical intervention or therapy. The rapidly evolving landscape of CTC biology has opened new avenues for understanding cancer progression, metastasis, and treatment response. Additionally, translating these findings into clinical applications holds promise for improving cancer diagnostics, prognosis, and personalized therapeutic strategies. This review discusses the significance of CTCs in cancer research and their associated challenges. We explore recent developments in the detection and characterization of CTCs and their implications in cancer research and clinical practice.

Growth environment greatly alters many facets of pathogen physiology, including pathogenesis and antimicrobial tolerance. The importance of host-mimicking environments for attaining an accurate picture of pathogen behaviour is widely recognised. Whilst this recognition has translated into the extensive development of artificial cystic fibrosis (CF) sputum medium, attempts to mimic the growth environment in other respiratory disease states have been completely neglected. The composition of the airway surface liquid (ASL) in different pulmonary diseases is far less well characterised than CF sputum, making it very difficult for researchers to model these infection environments. In this review we discuss the components of human ASL, how different lung pathologies affect ASL composition, and how different pathogens interact with these components. This will provide researchers interested in mimicking different respiratory environments with the information necessary to design a host-mimicking medium, allowing for better understanding of how to treat pathogens causing infection in these environments.

Background: Circulating rare cells participate in breast cancer evolution as systemic components of the disease and thus, are a source of theranostic information. Exploration of cancer-associated rare cells is in its infancy. We determined the validity of a rare-cell detection platform and demonstrated the usefulness of a certain rare cell subset as a novel approach to characterize the breast cancer system. Methods: Linearity of the Rarmax® platform was established using a spike-in approach. The platform includes red blood cell lysis, leukocyte depletion and high-resolution fluorescence image recording. Rare cell analysis was conducted on 28 samples (before and after surgery) from 14 patients with breast cancer, 20 healthy volunteers and 9 non-cancer control volunteers. In-depth identification of rare cells, including circulating tumor cells, endothelial-like cells, erythroblasts and inflammation-associated cells, was performed using a phenotype and morphology-based classification system. Results: The platform performed linearly over a range of 5-950 spiked cells, with an average recovery of 84.6%. Circulating epithelial and endothelial-like cell subsets have been demonstrated to be associated with or independent of cancer with tumor presence. Furthermore, certain cell patterns may be associated with treatment-related adverse effects. The sensitivity in detecting tumor-presence and cancer-associated abnormality before surgery was 50% and 85.7%, respectively and the specificity was 100% and 96.6%, respectively. Conclusion: The present study supports the idea of a cancer-associated rare cell abnormality to represent tumor entities as well as systemic cancer. The latter is independent of the apparent clinical cancer.

This study explores the dynamics of liquid holdup in a lab-scale co-current two-phase upflow moving packed bed reactor, specifically examining how superficial gas velocity influences the line average external liquid holdup at a fixed superficial liquid velocity. Utilizing Gamma-ray Densitometry (GRD) for precise measurements, this research extends to determining line average internal porosity within catalyst particles and the overall external bed porosity. Conducted with an air-water system within a bed packed with 3 mm extrudate porous particles, the study presents a novel methodology to calculate liquid holdup, grounded in Beer–Lambert's law. Findings reveal a decrease in liquid holdup corresponding with increased superficial gas velocity across axial and radial locations, with a notable transition from bubbly to pulse flow regime at a critical velocity of 3.8 cm/sec. Additionally, the lower sections of the packed bed exhibited higher external liquid holdup compared to the middle sections at varied gas velocities. The liquid holdup distribution appeared uniform at lower flow rates, whereas higher flow rates favored the middle sections.

We report the use of four-layer graphene (4LG) as a highly reliable transparent conductive electrode (TCE) for polymer-dispersed liquid crystal (PDLC)-based smart window devices. The adhesion between 4LG and the substrate was successfully improved through a water-induced interface-cleaning (WIIC) process. We compared the performance of a device with a WIIC-processed 4LG electrode with that of devices with a conventional Indium tin oxide (ITO) electrode and a 4LG electrode without a WIIC. With the application of the WIIC process, the PDLC smart window with a 4LG electrode exhibited reduced turn-on voltage and haze compared to 4LG without the WIIC process and characteristics comparable to those of the ITO electrode. Based on our observations, we conclude that 4LG with WIIC is a promising TCE for flexible smart windows.

Recently, there is a growing need for sensors that can operate autonomously, without the need for an external power source. This is especially important in applications where conventional power sources, such as batteries, are impractical or difficult to replace. Self-powered sensors have emerged as a promising solution to this challenge, offering a range of benefits such as low cost, high stability, and environmental friendliness. One of the most promising self-powered sensor technologies is L-S TENG, which stands for the liquid-solid triboelectric nanogenerator. This technology works by harnessing the mechanical energy generated by external stimuli such as pressure, touch, or vibration, and converting it into electrical energy that can be used to power sensors and other electronic devices. Therefore, self-powered based on L-S TENG, which provides numerous benefits such as rapidly responding, portability, cost-effectiveness, and miniaturization, is critical for increasing living standards and optimizing industrial processes. In this review paper, the working principle with three basic modes has been briefly introduced firstly. After that, affecting parameters to L-S TENG are reviewed based on the properties of the liquid and solid phases. With different working principles, L-S TENG has designed a lot of structure that works as a self-powered sensor for pressure/force change, liquid flow motion, concentration, and chemical detection or biochemical sensing. Moreover, the continuous output signal of TENG plays an important role in a real-time sensor that is vital to the growth of the Internet of Things.

The physiological characteristics of liquid digestate retrieved from various biogas plants based in northern Greece are presented. Preliminary photocatalysis experiments on inoculated liquid di-gestate sampled showed that disinfection is possible when pre-treated digestate with a combination of centrifuge-flocculation-μFiltration after 5.5 hours of 0.7g/L suspended TiO2 under UVA illumination for the experimental conditions is used. A novel design photocatalytic nanofiltration reactor was implemented for disinfection experiments on pre-treated liquid digestate, giving promising results. This work sets the basis for the efficient operation and engineering application of technology collaboration with photocatalysis as the final step for liquid digestate sanitation and reusable water recovery.

The process of ultrasonic atomization involves a series of dynamic/topological deformations of free surface, though not always, of a bulk liquid (initially) below the air. This study focuses on such dynamic interfacial alterations realized by changing some acousto-related operating conditions, including ultrasound excitation frequency, acoustic strength or input power density, and the presence/absence of a “stabilizing” nozzle. High-speed, high-resolution imaging made it possible to qualitatively identify four representative transitions/demarcations: 1) the onset of a protrusion on otherwise flat free surface; 2) the appearance of undulation along the growing protuberance; 3) the triggering of emanating beads fountain out of this foundation-like region; and 4) the induction of droplets bursting and/or mist spreading. Quantitatively examined were the two-parameters specifications—on the degrees as well as induction—of the periodicity in the protrusion-surface and beads-fountain oscillations, detected over wider ranges of driving/excitation frequency (0.43–3.0 MHz) and input power density (0.5–10 W/cm2) applied to the ultrasound transducer of flat surface on which the nozzle was mounted or not. The resulting time sequence of images processed for the extended operating ranges, regarding the fountain structure pertaining in particular to recurring beads, confirms the wave-associated nature, i.e., their size “scalability” to the ultrasound wavelength, predictable from the traveling wave relationship. The thresholds in acoustic conditions for each of the four transition states of the fountain structure have been identified—notably, the onset of plausible “bifurcation” in the chain-beads diameter below a critical excitation frequency.

This work aims to investigate the effect of process temperature and catalyst content by pyrolysis and thermal catalytic cracking of (organic matter + paper) fraction from municipal household solid waste (MHSW) on the yields of reaction products (bio-oil, bio-char, H2O, and gas), acid value and chemical composition of bio-oils, and characterization of bio-chars, in laboratory scale. The collecting sectors of MHSW in the municipality of Belém-Pará-Brazil were chosen based on geographic and socio-economic database. The MHSW collected and transported to the segregation area. The gravimetric analysis of MHSW carried out and the fractions (Paper, Cardboard, Tetra Pack, Hard Plastic, Soft Plastic, Metal, Glass, Organic Matter, and Inert) separated. The selected organic matter and paper submitted to pre-treatment of crushing, drying, and sieving. The experiments carried out at 400, 450, and 475 °C and 1.0 atmosphere, and at 475 °C and 1.0 atmosphere, using 5.0, 10.0, and 15.0% (wt.) Ca(OH)2, in batch mode. The bio-oil characterized for acid value. The chemical functions present in bio-oil identified by FT-IR and the composition by GC-MS. The bio-char characterized by SEM, FT-IR and XRD. The variance in mass (wt.%) for organic fraction of municipal household solid waste, between 56.21 and 67.45% (wt.), lies with the interval of 56% (wt.) and 64% (wt.) of OFMHSW for middle and low income countries. The pyrolysis of MHSW fraction (organic matter + paper) show bio-oil yields between 2.63 and 9.41% (wt.), aqueous phase yields between 28.58 and 35.08% (wt.), solid phase yields between 35.29 and 45.75% (wt.), and gas yields between 16.54 and 26.72% (wt.). The bio-oil yield increases with pyrolysis temperature. For the catalytic cracking, the bio-oil and gas yields increase slightly with CaO content, while that of bio-char decreases, and the H2O phase remains constant. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, alkynes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, phenols, and aldehydes), as well as compounds containing nitrogen, including amides and amines. The acidity of bio-oil decreases with increasing process temperature and with aid Ca(OH)2 as catalyst. The concentration of hydrocarbons in bio-oil increases with increasing Ca(OH)2-to-MHSW fraction ratio due to the catalytic deoxygenation of fatty acids molecules, by means of de-carboxylation/de-carbonylation, producing aliphatic and aromatic hydrocarbons.

This review summarises the main numerical models of fuel droplet heating and evaporation (DHE) in combustion engines across the different scales by accessing the nano/micro, meso and macroscopic fluid elements. The phenomena of multi-physics, multi-scale and multi-phase fluid flow and heat transfer are fully investigated when the fuel droplet (dodecane) is heating and evaporated into a background gas (nitrogen) crossing the liquid-vapour (LV) interface, kinetic region (i.e., Knudsen layer) and the bulk regions of liquid and gas in terms of molecular dynamics (MD) simulations, kinetic theory modelling (i.e., direct numerical solutions of Boltzmann equations) and convectional fluid dynamics approach, respectively. The evaporation coefficient of fuel evaporating molecules and their velocity distributions at the LV interface derived from MD simulations formulate a new kinetic boundary condition (KBC). Moreover, a novel kinetic model considering the inelastic collision between fuel molecules alongside the new KBC enables us to describe the non-equilibrium gas dynamics of fuel vapour and gas mixture in Knudsen layer (KL). Heat and mass flux analysis of the fuel droplet under combustion engine conditions can be accurately assessed by implementing the inelastic collision between fuel molecules in KL and a temperature-dependent evaporation coefficient at the LV interface into DHE. The surface temperature of fuel droplet and its evaporation time, which play a significant role in resolving the ignition delay and hence the combustion phasing in engines, can also be well estimated. The multi-scale modelling of fuel DHE will make significantly potential input into the cleaner engine targeting the low-carbon emissions and enhance the capability of the existing computational fluid dynamics (CFD) solvers.

This work aims to investigate the effect of catalyst content and reaction time by catalytic upgrading from pyrolysis vapors of residual fat at 450 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, refractive index, and acid value) and chemical composition of organic liquid products (OLP), over a catalyst fixed bed reactor, in semi pilot scale. Pellets of Red Mud chemically activated with 1.0 M HCl were used as catalysts. The experiments were carried out at 450 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) Red Mud pellets activated with 1.0 M HCl, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 40, 50, 60, 70 and 80 min in order to analyze the process kinetics. The physicochemical properties (density, kinematic viscosity, acid value, and refractive index) of OLP were determined by official methods. The chemical functions present in OLP determined by FT-IR and the chemical composition by GC-MS. The thermal catalytic cracking of residual fat show OLP yields from 54.4 to 84.88 (wt.%), aqueous phase yields between 2.21 and 2.80 (wt.%), solid phase yields (coke) between 1.30 and 8.60 (wt.%), and gas yields from 11.61 to 34.22 (wt.%). The yields of OLP increases with increasing catalyst content while those of aqueous, gaseous and solid phase decreases. For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of OLP decreases with increasing reaction time. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the thermal and thermal catalytic cracking experiments, the hydrocarbon content within OLP increases with reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties (density, kinematic viscosity, and acid value) and the maximum hydrocarbon content of OLP were obtained at 450 °C and 1.0 atmosphere, using a catalyst fixed bed reactor, with 5.0% (wt.) Red Mud pellets activated with 1.0 M HCl as catalyst.

Falling snow alters its own microwave signatures when it begins to accumulate on the ground, making retrieval of snowfall challenging. This paper investigates the effects of snow-cover depth and cloud liquid water content on microwave signatures of terrestrial snowfall using reanalysis data and multi-annual observations by the Global Precipitation Measurement (GPM) core satellite with particular emphasis on the 89 and 166 GHz channels. It is found that over shallow snow cover (snow water equivalent (SWE) ≤ 100 kg m^-2) and low values of cloud liquid water path (LWP 100–150 g m^-2), the scattering of light snowfall (intensities ≤ 0.5 mm h⁻¹) is detectable only at frequency 166 GHz, while for higher snowfall rates, the signal can also be detected at 89 GHz. However, when SWE exceeds 200 kg m^-2 and the LWP is greater than 100–150 g m^-2, the emission from the increased liquid water content in snowing clouds becomes the only surrogate microwave signal of snowfall that is stronger at frequency 89 than 166 GHz. The results also reveal that over high latitudes above 60°N where the SWE is greater than 200 kg m^-2 and LWP is lower than 100–150 g m^-2, the snowfall microwave signal could not be detected with GPM without considering a priori data about SWE and LWP. Our findings provide quantitative insights for improving retrieval of snowfall in particular over snow-covered terrain.

We report the effect of doping Cd1-xZnxS/ZnS core/shell quantum dot (CSQDs) in nematic liquid crystal p-methoxybenzylidene p-decylaniline (MBDA) at 0.05 wt/wt%, 0.1 wt/wt%, 0.15 wt/wt%, 0.2 wt/wt%, 0.25 wt/wt% and 0.3 wt/wt% concentrations of CSQDs in MBDA. Dielectric parameters with and without bias with respect to frequency has been investigated. The change in electro - optical parameters with temperature has also been demonstrated. The increase in the mean dielectric permittivity has been found due to large dipole moment of CSQDs which impose stronger interactions with the liquid crystal molecules. The dielectric anisotropy changes sign on doping CSQDs in MBDA liquid crystal. It was concluded that the CSQDs doping noticeably increases the dielectric permittivity of nematic MBDA in the presence of electric field. The doping of CSQDs in nematic MBDA liquid crystal reduces the ion screening effect effectively. This phenomenon is attributed to the competition between the generated ionic impurities during assembling process and the ion trapping effect of the CSQDs. The rotational viscosity of nematic liquid crystal decreases with increasing concentration of the CSQDs with faster response time observed for 0.05 wt/wt% concentration. The birefringence of the doped system increases with the inclusion of CSQDs in MBDA. These results find application in the field of display devices, phase shifters, industries and projectors.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

Three-dimensional nanocomposite networks consisting of percolated Si nanowires in a SiO₂ matrix, Si:SiO₂, were studied. The structures were obtained by reactive ion beam sputter deposition of SiO_x (x ≈ 0.6) thin films at 450 °C and subsequent crystallization using conventional oven as well as millisecond line focus laser annealing. Rutherford backscattering spectrometry, Raman spectroscopy, X-ray diffraction, cross-sectional and energy-filtered transmission electron microscopy were applied for sample characterization. While oven annealing resulted in a mean Si wire diameter of 10 nm and a crystallinity of 72 % within the Si volume, almost single-domain Si structures with 30 nm in diameter and almost free of amorphous Si were obtained by millisecond laser application. The structural differences are attributed to the different crystallization processes: Conventional oven tempering proceeds via solid state, millisecond laser application via liquid phase crystallization of Si. The 5 orders of magnitude larger diffusion constant in the liquid phase is responsible for the three times larger Si nanostructure diameter. In conclusion, laser annealing offers not only significantly shorter process times but moreover a superior structural order of nano-Si compared to conventional heating.

The LiCl and LiNO₃ water solutions in the presence of small amounts of 3-helium have been investigated by means of multinuclear resonance spectroscopy. The resulting concentration dependences of the ³He, ^6,7Li⁺, ¹⁴NO₃^¯ and ³⁵Cl^¯ resonance radiofrequencies are reported in the infinite limit. This data along with new theoretical corrections of shielding lithium ions was analyzed by a known NMR relationship method. Consequently, the nuclear magnetic moments of ⁶Li and ⁷Li were established against that of the helium-3 dipole moment: μ(⁶Li)=+0.822046(5)μ_N and μ(⁷Li)=+3.256418(20)μ_N. The new results were shown to be very close to the previously obtained values of the (ABMR) atomic beam magnetic resonance method. This experiment proves that our helium method is well suited for establishing dipole moments from NMR measurements performed in water solutions. This technique is especially valuable when gaseous substances of the needed element are not available. All shielding constants of species present in water solutions are consistent with new nuclear magnetic moments and these taken as a reference. Both techniques – NMR and ABMR – give practically the same results providing that all shielding corrections are properly made.

Aluminium dross is the industrial waste from aluminium refining industry and accordance with toxic waste materials, it’s also recognized as a by-product of aluminium production, has historically posed significant environmental challenges due to its toxic and reactive nature. However, recent advancements in technology have revealed the potential of transforming aluminium dross into a valuable source of white hydrogen. This review paper explores the methodologies, benefits, and challenges associated with this transformation. By analysing current research and industrial practices, our review highlighted the potential of this innovative approach to mitigate waste and contribute to sustainable energy solutions. In addition, the utilization of Aluminium dross can be considered as innovative and advancement in sustainable waste management strategy instead of direct disposal, and hot springs use advances in direct utilization. Our experimental work achieved white hydrogen maximum flowrate at 600 sec. with 120ºC.

Background: Dietary fiber is a key component of a health-promoting diet, and it is acknowledged as a short-fall nutrient in most Western diets. Some sources of dietary fiber, such as hemp hull fiber, also include inherent small molecule bioactives that further promote health and well-being. While dietary fiber is a key component that supports digestive health, it also can cause digestive discomfort. Digestive symptoms such as gas, bloating, belly pain, and the resulting decrease in digestive quality of life are common among adults. The aim of this study was to evaluate changes in digestive comfort, in individuals who currently experience digestive discomfort, after consuming either a proprietary dietary fiber supplement from hemp hull, a dietary fiber supplement made from inulin, or a digestible control (maltodextrin). Methods: This study was a completely virtual, double-blind, placebo-controlled, randomized clinical trial of healthy adults. The parallel arm study tested two fiber supplements at a practical dose yielding a “Good Source of Fiber” based on United States Dietary Reference Intakes (2.8 grams of fiber per day) for six weeks. Results Five hundred seventy nine randomized participants provided follow-up outcomes data. Digestion-associated quality of life questionnaire, belly pain, and gas and bloating scores were assessed and found to be superior after hemp hull fiber intake compared to inulin intake at multiple time points in a post-hoc analysis (p<0.05). Conclusion This study demonstrated that a practical dose of bioactive-rich fiber from hemp hull is well-tolerated, provides superior digestive comfort relative to both placebo and inulin fiber, and can aid in reaching total fiber intake goals.

Microplastics, pervasive in both terrestrial and aquatic ecosystems, have emerged as significant contributors to greenhouse gas (GHG) emissions, including carbon dioxide (CO2), methane (CH4), and nitrous oxide (N2O). This review synthesizes recent studies from 2019 to 2024, revealing the complex mechanisms through which microplastics influence GHG production. These mechanisms include the adsorption of nutrients and pollutants onto microplastic surfaces and their role as substrates for microbial colonization. The impacts of microplastics vary significantly across different environments, such as agricultural soils and marine sediments. The review underscores the urgent need for standardized methodologies and long-term field studies to accurately assess the ecological consequences of microplastics. Notably, the role of nitrous oxide (N2O), a potent GHG with a global warming potential nearly 300 times that of CO2, remains underexplored in the context of microplastic interactions, highlighting a critical research gap. Additionally, the synergistic effects of microplastics with other pollutants require further investigation to fully understand their cumulative impact on GHG emissions. This review calls for a coordinated effort among researchers and policymakers to advance our understanding of microplastics' role in global GHG budgets and to develop effective strategies for mitigating their environmental and climatic impacts.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

As the understanding of natural gas hydrates as a vast potential resource deepens, their importance as a future clean energy source becomes increasingly evident. However, natural gas hydrates tend to secondary generation during extraction and transportation, leading to safety issues such as pipeline blockages. Consequently, developing new and efficient natural gas hydrate inhibitors has become a focal point in hydrate research. Kinetic Hydrate Inhibitors (KHIs) offer an effective solution by disrupting the nucleation and growth processes of hydrates without altering their thermodynamic equilibrium conditions. This paper systematically reviews the latest research progress and development trends of KHIs for natural gas hydrates, covering their development history, classification, and inhibition mechanisms. It particularly focuses on the chemical properties, inhibition effects, and mechanisms of polymer inhibitors such as polyvinylpyrrolidone (PVP) and polyvinylcaprolactam (PVCap). Studies indicate that these polymer inhibitors provide an economical and efficient solution due to their low dosage and environmental friendliness. Additionally, this paper explores the environmental impact and biodegradability of these inhibitors, offering guidance for future research, including the development, optimization, and environmental assessment of new inhibitors. Through a comprehensive analysis of existing research, this work aims to provide a theoretical foundation and technical reference for the commercial development of natural gas hydrates, promoting their safe and efficient use as a clean energy resource.

The ubiquitous nature of polymers have led to a widespread demand for sustainable polymers in numerous industrial applications. However, lack of well laid out guidelines, product development pathways and certifications have resulted in a lot of commotions and confusions within the polymer value chain. Herein, a meticulous review is conducted on the topic of polymer sustainability shedding light on the standards, product declarations, biobased-biomass concepts, product carbon footprint etc. It is critical that companies significantly contribute on such sustainability efforts in lieu of market readiness and competitive advantages. Any discussion within the sustainability horizon references a couple of terms/ abbreviations/concepts. In this article, such key terminologies and concepts related to polymer sustainability are reviewed with a holistic outlook on the widespread approaches within the polymer sustainability horizon.

The integration of commodities into stock exchanges marked a pivotal moment in the analysis of price dynamics. Commodities, essential for both daily sustenance and industrial processes, encompass hard commodities like metals and energy, alongside soft commodities such as agricultural produce. This paper investigates the implications of commodity price volatility on commercial and financial landscapes, recognizing its profound impact on global economies. This study employs a meticulous methodology, delineated into four stages: identification, control, and final selection of academic articles, culminating in their tabulation. Methodologically, a literature review serves as the primary tool for data acquisition, with a focus on existing scientific knowledge to bridge gaps and propose avenues for further inquiry. Drawing from reliable sources, including Google Scholar and Science Direct, the research navigates through a wealth of scholarly discourse on commodity market dynamics. By analyzing trends in academic publications, particularly focusing on the interplay between volatility spillover and gold, this paper provides insights into the evolution of research paradigms over time. Ultimately, this paper not only synthesizes existing knowledge but also identifies lacunae for future investigation, thereby contributing to a deeper understanding of the complexities surrounding commodity markets and their ramifications on global economies.

This article presents a detailed examination of the methodology and modeling tools utilized to analyze gas flow in pipelines, rooted in the fundamental principles of gas dynamics. The methodology integrates numerical simulations with modern neural network techniques, particularly focusing on the Physics-Informed Neural Network (PINN) method. This innovative approach combines artificial neural networks (ANNs) with physical equations, offering a more efficient and accurate way to model various complex processes and phenomena. The proposed mathematical model, based on the Euler equation, has been meticulously implemented using the Python language. Verification with analytical solutions ensures the accuracy and reliability of the computations. In the research, a comprehensive comparative analysis was conducted between results obtained using the PINN method and those from conventional Computational Fluid Dynamics (CFD) approaches. The analysis highlighted the advantages of the PINN method, which produced smoother pressure and velocity fluctuation profiles while reducing computation time, demonstrating its potential as a transformative modeling tool. The data derived from this study are of paramount importance for ensuring ongoing energy supply reliability and can also be used to create predictive models related to gas behavior in pipelines. The application of modeling techniques for gas flow simulation has the potential to revolutionize the integrity of our energy infrastructure and utilization of gas resources. However, it is crucial to emphasize that the effectiveness of such models relies on continuous monitoring and frequent updates to ensure alignment with real-world conditions. This research not only contributes to a deeper understanding of compressible gas flows but also underscores the crucial role of advanced modeling methodologies in the sustainable management of gas resources for both current and future generations.

Gas leakage can occur for various reasons, including a gas leak in the distribution line, damaged regulators, service connection failures, fluctuations in inlet gas pressure, and other factors leading to millions in losses to the state. The objective is to develop a general and intelligent model for tracking and monitoring LPG distribution based on the Internet of Things and Business Intelligence technology. Devices such as sensors and actuators reduce risks and prevent accidents. IoT can also access automatic control of machines and infrastructure, and sensors’ data helps make intelligent decisions. The quantitative approach is used in the systematic review methodology based on the PRISMA statement; the architecture design is based on analytical research that studies the feasibility of a measure through empirical evidence; and the architecture description uses a qualitative approach. The Y.4908 Standard evaluates an IoT network’s interoperability, usability, and security. A targeted group of thirty IT professionals was surveyed to assess the Business Intelligence model. Forty scientific papers were selected for analysis. A model with IoT components and a four-level business intelligence system was found. At the overall average level, 49% strongly agree, 38% agree, 12% neither agree nor disagree, and 1% disagree. In other words, the model has an overall average approval rating of 87%.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

Certain configurations of liquefied natural gas refueling stations exhibit a deficiency in managing boil-off gas. Furthermore, the ill-conceived linkage between the submersible pump and the gas storage tank pipeline leads to impeded natural gas transmission. This study employs Computational Fluid Dynamics (CFD) methodology to scrutinize the hydrodynamic attributes of T-type tee and dovetail tee configurations implemented in the pipeline design connecting the submersible pump and storage tank in an LNG filling station across diverse operational scenarios. The T-type tee induces detachment of the primary flow from the inner wall due to inertial forces, resulting in vortex formation and heightened resistance, accompanied by increased energy dissipation. Conversely, the dovetail tee, with its circular wall transition, mitigates vortex generation, reducing the separation zone and consequently minimizing resistance and energy loss. The maximum static differential pressure between the inlet and outlet of the dovetail tee is diminished by 52.52% when compared to that of the T-type tee. In the most noteworthy scenarios, the local resistance coefficient of the dovetail tee is even less than 1/10 of that of the T-type tee. In practical engineering applications, the incorporation of dovetail tees leads to a 17.58% reduction in the required elevation difference. This results in a more uniform flow field and enhanced stability in both flow rate and pressure. Such improvements contribute to heightened engineering efficiency and environmental sustainability, particularly evident in the design of LNG filling stations.

This paper presents a comprehensive study based on multiphase seepage and wellbore multiphase flow theories. It establishes a gas intrusion rate calculation model that considers various factors including formation pore permeability, bottomhole pressure difference, drilling fluid rheology, and surface tension. Experiments were conducted to investigate the gas intrusion mechanism under shut-in conditions, and the experimental results were employed to validate the reliability of the proposed gas intrusion rate calculation method. Furthermore, the research explores the transportation rates of single bubbles and bubble clusters in drilling fluid under shut-in conditions. Meanwhile, empirical expressions were derived for the drag coefficient for single bubbles and bubble clusters in the wellbore. These expressions can be used to calculate gas transportation rates for various equivalent radii of single bubbles and bubble clusters. Additionally, a method was developed for calculating the rising velocity of bubble clusters in water based on experimental results. The study reveals that the average bubble size in the bubble cluster is significantly smaller than the size of the single bubble generated from the orifice. When the viscosity of the drilling fluid is low, the bubble cluster transportation velocity exhibits a positive correlation with the average bubble diameter. When the average bubble diameter exceeds 1 mm, the bubble velocity no longer varies with the change in the bubble cluster diameter. The initial bubble size of intrusive gas, the transportation speed of intrusive gas in the wellbore, the gas intrusion rate, and variations of the wellbore pressure after gas intrusion were analyzed. The research results provide theoretical support for wellbore pressure prediction and pressure control under shutdown conditions.

The chromatographic conditions were optimized using headspace gas chromatography, and a simple and rapid method was established for the simultaneous determination of five residual solvents in ursodeoxycholic acid raw materials. The corresponding quality standards were revised. The results showed that the concentration of methanol ranged from 0.06mg/ml to 0.3mg/ml, and the concentrations of acetone, tert butanol, ethyl acetate, and triethylamine showed a good linear relationship with the peak area within the range of 0.1mg/ml to 0.5mg/ml (r=0.999); The quantitation limits for methanol, acetone, tert-butanol, ethyl acetate, and triethylamine were 4.2, 0.9, 1.5, 1, and 0.1 μg/ml, respectively, with detection limits of 1.2, 0.25, 0.025, 0.3, and 0.025 μg/ml, respectively. The recovery rates of each solvent ranged from 92.9% to 106.0%, with RSD% (n=9) less than 3.8%; The method exhibited good repeatability, with RSD% (n=6) less than 2.5%. Furthermore, the durability is good. The established method is simple, accurate, specific, and highly sensitive, and can be used for the simultaneous and rapid determination of five residual solvents in ursodeoxycholic acid raw materials.

Quantification of the trade-offs among greenhouse gas (GHG) emissions, yield and farmers’ incomes is essential for proposing economic and environment nitrogen (N) management strategies for optimizing agricultural production. A four-year (2017–2020) field experiment (including four treatments: control experiment (CK), suitable utilization of fertilization (SU), emission reduction treatment (ER), and high fertilization (HF)) was conducted on maize (Zea mays L.) in the North China Plain. The Life Cycle Assessment (LCA) method was used in this study to quantify the GHG emissions and farmers’ incomes during the whole maize production process. The total GHG emissions of CK, SU, ER and HF treatments in the process of maize production are 10,755.2, 12,908.7, 11,950.1, and 14,274.5 kg CO2-eq ha−1 respectively, of which the direct emissions account for 84.8%, 76.8%, 74.9%, and 71.0%, respectively. Adding inhibitor significantly reduced direct GHG emissions, and the N2O and CO2 emissions from the maize fields in the ER treatment decreased by 30.0% and 7.9% compared to those in the SU treatment. Insignificant differences in yield were found between the SU and ER treatments, indicating that adding fertilizer inhibitors did not affect farmers’ incomes while reducing GHG emissions. The yield for SU, ER and HF treatments all significantly increased by 12.9%–24.0%, 10.0%–20.7% and 2.1%–17.4% compared to CK, respectively. In comparison with CK, both SU and ER significantly promoted agricultural net profit (ANP) by 16.6% and 12.2% with the mean ANP values of 3,101.0 USD ha-1 and 2,980.0 USD ha-1, respectively. Due to the high agricultural inputs, the ANP values in the HF treatment was 11.2%, 16.6% and 12.4% lower than those in the SU treatment in 2018–2020. In conclusion, the combination of N fertilizer and inhibitors was proved to be an environmentally friendly, high-profit and low-emissions production technology while sustaining or even increasing maize yields in the North China Plain, which was conducive to achieving agricultural sustainability.

The aim of this article is to review hydrogen combustion applications within the energy transition framework. Hydrogen blends are also included, from the well known hydrogen enriched natural gas (HENG) to the hydrogen and ammonia blends whose chemical kinetics is still not clearly defined. Hydrogen and hydrogen blends combustion characteristics will be firstly summarized, in terms of standard properties like the laminar flame speed and the adiabatic flame temperature, but also evidencing the critical role of hydrogen preferential diffusion in burning rate enhancement and the drastic reduction in radiative emission with respect to natural gas flames. Then, combustion applications in both thermo-electric power generation (based on internal combustion engines, i.e., gas turbines and piston engines) and hard-to-abate industry (requiring high temperature kilns and furnaces) sectors will be considered, highlighting the main issues due to hydrogen addition related to safety, pollutant emissions, and potentially negative effects on industrial products (e.g., glass, cement and ceramic).

This study presents a novel approach for predicting hierarchical short time series. In this article, our objective was to formulate long-term forecasts for household natural gas consumption by considering the hierarchical structure of territorial units within a country's administrative divisions. For this purpose, we utilized natural gas consumption data from Poland. The length of the time series was an important determinant of the data set. We contrast global techniques, which employ a uniform method across all time series, with local methods that fit a distinct method for each time series. Furthermore, we compare the conventional statistical approach with a machine learning (ML) approach. Based on our analyses, we devised forecasting methods for short time series that exhibit exceptional performance. We have demonstrated that global models provide better forecasts than local models. Among ML models, neural networks yielded the best results, with the MLP network achieving comparable performance to the LSTM network while requiring significantly less computational time.

This paper Numerically investigates the effectiveness of the turbine rotating blade nozzle position on the vortex and film composite cooling performance. The coolant injecting nozzles arranged near the pressure surface side (PS-side-in) .vs. arranged near the suction surface side (SS-side-in) are compared at the rotating speed range of 0-4000rpm with fluid and thermal conjugate approach. Results show that the nozzle position presents different influences under low and higher rotating speed. In terms of the mainstream flow, rotation makes the stagnation line move from the PS-side pressure surface side to the SS-side suc-tion surface side, which changes the coolant film attachment on the blade leading edge surface. The nozzle position however indicates limited influence on the coolant film flow. In terms of the internal channel vortex flow, the coolant injecting from the nozzles forms a high-velocity region near the target wall which brings about enhancing convective heat transfer. The direction of the near wall vortex flow is opposite and align to the Coriolis force direction in both the PS-side-in and SS-side-in, respectively. Therefore, the Coriolis force augments to the heat transfer of the internal vortex cooling in SS-side-in while weakens the internal heat transfer in PS-side-in. Such effects become more intense with higher rotational speed. The blade surface area-averaged dimensionless temperature that inversely proportional to the actual temperature is 7.8% higher in SS-side-in as compared to that in PS-side-in. The SS-side-in suggests more superior composite cooling perfor-mance under the relatively higher rotating speed.

The offshore oil and gas working environment is an inherently dangerous one, with risks posed to physical safety on a daily basis. One neglected field of research is the added psychosocial stressors present in this environment. This research examined the experiences of offshore oil and gas workers through one-on-one online interviews which were recorded and transcribed. Transcripts were analysed through qualitative software NVivo, which generated themes and patterns for the responses given to questions which were developed through a focus group. The results of the analysis showed that multiple psychosocial stressors are present for this population, such as fear of speaking up, unsatisfactory company-provided facilities, work-life interference, work status, micromanaging, gender harassment and bullying. In addition, interviews identified that production and time pressures along with fatigue can influence accidents and mistakes. Climate factors also cause discomfort, however these are managed according to best practice by organisations. Due to the timing of the study, COVID-19 was a significant stressor for some, but not all, employees. In conclusion, offshore oil and gas workers face multiple stressors in a dangerous environment that may lead to devastating consequences.

In this study, three paddy harvesting systems; manual harvesting of paddy (MHP), reaper harvesting of paddy (RHP), and combine harvesting of paddy (CHP) were evaluated considering field capacities, field efficiencies, time and fuel consumption, mechanization indices, greenhouse gas emissions, straw availability, and direct and indirect costs. Field experiments were conducted in North central province of Sri Lanka. The effective field capacity, field efficiency and fuel consumption of the combine harvester were 0.34 hah-1, 60.8%, and 34.1 Lha-1, respectively, and those of the paddy reaper were 0.185 hah-1, 58.2%, and 3.8 Lha-1, respectively. The total time consumed by MHP, RHP, and CHP were 76.05 hha-1, 39.76 hha-1, and 2.94 hha-1, respectively. The highest energy utilization was recorded by the CHP, at 1851.09 MJha-1, while MHP recorded the lowest at 643.20 MJha-1. The direct cost of the MHP was 1.50 and 1.52 times higher than those of the CHP and RHP, respectively. MHP recorded the lowest greenhouse gas emissions (32.94 kgCO2eqha-1), while CHP recorded the highest (176.29 kgCO2eqha-1). The RHP exhibited an intermediate level in all aspects. Although the CHP has higher field performance and direct costs, it brings higher GHG emissions and indirect costs. Therefore, an optimum level of mechanization should be introduced for the long-term sustainability of both the environment and farming.

In this study, GC–IMS was used to analyze the volatile component and flavor profiles of Crassostrea gigas individuals of different ploidy and gender. Principal component analysis was used to explore overall differences in flavor profiles and a total of 54 volatile compounds were identified. The total volatile flavor contents in edible parts of tetraploid oysters were significantly higher than in diploid and triploid oysters. The concentrations of ethyl (E)-2-butenoate and 1-penten-3-ol were significantly higher of triploid oysters than in diploid and tetraploid oysters. In addition, the volatile compounds propanoic acid, ethyl propanoate, 1-butanol, butanal, and 2-ethyl furan were significantly higher in females than in males. The volatile compounds p-methyl anisole, 3-octanone, 3-octanone, and (E)-2-heptenal were present in higher levels in male than in female oysters. Overall, different ploidy and gender of oysters were being presented with different sensory characteristics, providing new insights for understanding the flavor characteristics of oysters.

Indirect calorimetry (IC) is a widely used method to study animal energy metabolism by measuring gas exchange. The accuracy of IC depends on detecting variations in signals reflecting the metabolic response, which can be challenging due to measurement noise and external factors. In this study, we propose a methodology to validate IC systems, including an easy-to-use spreadsheet for data computing, to verify accuracy and detect whole-system leaks. We conducted a re-covery test using a simulation of CO2 dynamics in MS Excel and injecting a known CO2 concentration into four respirometry chambers. The clearance rate of CO2 was observed and compared to the expected clearance rate from the simulation. The results from the recovery test in our system show that the proposed methodology is accurate and precise. The proposed methodology and recovery test can be used to standardize the validation of IC systems, providing accurate measurements of animal energy metabolism in different environmental conditions and energy utilization from feeds.

The military taxonomy of class indices for chemical and biological warfare agents considers halogenated tear agents (CS) to be incapacitating causing local pain and discomfort with associated reflexe. The removal yield of the organic substances present in the water depends on the environmental conditions, on the chemical composition of the water and on the chemical substance dissolved in the water, which constitutes the substrate of the metabolic activities of the microorganisms that use these substances in the biochemical reactions of the cellular enzyme complexes. The two -CN groups in the malonic nitrile molecule are strongly electron-attracting and activate the CH2 group to which they are linked, and because of this, malononitrile has the role of a methylene component in condensation reactions with aldehydes or ketones. The results obtained after analyzing the degree of hydrolysis in the samples that contained the biological suspension indicated that no CBM metabolites were detected in any biological sample, regardless of the test concentration, analyzed 24 h after incubation. In the parallel samples, the aqueous solutions of CBM without biological treatment had metabolites in the samples., at 30 minutes the degree of hydrolysis is 0.21%, at 60 minutes, the degree of hydrolysis is 5.42%, after 90 minutes, the degree of hydrolysis is 6.19%, and after 24 hours. the degree of hydrolysis is 23.41%. Chemical substances in contact with microorganisms are used by them in the biochemical processes in which they are involved, the retention time and biodegradation capacity have led to an increased effect of the metabolism of toxic substances, in metabolic reactions, organic substances are the source of carbon and energy for biochemical processes. The tests performed indicate that the suspension of Chlorella sp. consumed the entire amount of CBM and metabolites from the analyzed samples The tests prove that the biological material can be used for the decontamination of the affected areas.

The positive impact of nature on human health has been explored by researchers. Although studies have indicated that olfaction and odors have an impact on both memory and health, re-search on the odor perception in relation to perceived health is scarce. A recent study found that the naturenatural scent from stem cuttings and potted plants of a specific rose-scented geranium Pelargonium graveolens, ‘Dr. Westerlund,’Westerlund’ had positive effects on stress-related mental disorders. reduction. Essential oils from many Pelargonium species, in particular ‘Dr. Westerlund’, are known to have phytochemical properties and pharmacological activities. No study has, so far, explored and identified the chemical com-pounds and the sensory perception of these compounds in stem cuttings and the potted ´Dr. Westerlund´ plantplants. Such knowledge would be an important contribution forto an increased understanding of the effects of plants’ chemical odor properties on human well-being and link this to the expressed perceived scents. Resulting sensory profiles of P.This study aimed to identify the sensory profile and suggest responsible chemical compounds of Pelargonium graveolens ´Dr. Westerlund´ as a potted plant and as stem cuttings were reported, as well as´. The sensory and chemical analysis results revealed sensory profiles of Pelargonium graveolens ´Dr. Westerlund´s, and suggestions for the chemical compounds that are attributed to the sensory profiles. Further studies are recommended to investigate the odor experience of scented pelargonium species in relation to various levels ofcorrelation between volatile com-pounds and possible stress hormones. reduction in humans.

Natural ventilation in a building is an effective way to achieve acceptable indoor air quality. Ventilation dilutes contaminants such as bio-effluents generated by occupants, substances emitted from building materials, and water vapor generated by occupants' activities. In a building that requires heating and cooling, adequate ventilation is crucial to minimize energy consumption while maintaining healthy indoor air quality. However, measuring the actual magnitude of the ventilation rate, including infiltration through the building envelope and airflow through building openings, is not always feasible. In this study, the occupant-generated carbon dioxide (CO2) tracer gas decay method was applied to estimate the ventilation rates in an office room in Seoul, South Korea, from summer to winter. Using the method, real-time ventilation rates can be calculated by monitoring indoor and outdoor CO2 concentrations without injecting a tracer gas. 145mm-diameter circular openings on the fixed glass were used for natural ventilation in the test room. As a result, firstly, the indoor CO2 concentrations were used as an indicator to evaluate how much the indoor air quality deteriorated when all the windows were closed in an occupied office room compared to international standards for indoor air quality. Moreover, we found out the estimated ventilation rates varied depending on various environmental conditions, even with the same openings for natural ventilation. Considering the indoor and outdoor temperature differences and outdoor wind speeds as the main factors influencing the ventilation rates, we analyzed how they affected the ventilation rates in different seasons of South Korea. When the wind speeds were calm, the temperature difference played as a factor that influences the estimated ventilation rates. On the other hands, when the temperature differences were low, the wind speed was the primary factor. This study raises awareness about the risk of poor indoor air quality in office rooms that could lead to health problems or unpleasant working environments. This study presents an example of estimating the ventilation rates in an existing building. In the same way, the ventilation rate in an existing building can be simply estimated while using the building as usual, and appropriate ventilation strategies for the building can be determined to maintain desired indoor air quality.

Oxide semiconductors are conventionally being used as sensing materials in gas sensors, limiting the detection of gases at room temperature (RT). In this work, a hybrid of copper oxide (CuO) with functionalized graphene (rGO) is proposed to achieve gas sensing at RT. The combination of high surface area and presence of many functional groups in CuO/rGO hybrid material makes it highly sensitive for gas absorption and desorption. To prepare the hybrid material, a copper oxide suspension synthesized using copper acetate precursor is added to the graphene oxide solution during its reduction using ascorbic acid. Material properties of CuO/rGO hybrid and its drop-casted thin films are investigated using Raman, FTIR, SEM, TEM, and four-point probe measurement systems. We find that the hybrid material is enriched with oxygen functional groups (OFGs) and defective sites along with electrical conductivity (~1.5 kΩ/□). The fabricated QCM (quartz crystal microbalance) sensor with a thin layer of CuO/rGO hybrid, demonstrates a high sensing response which is twice the response of the rGO-based sensor for CO₂ gas at RT. We believe that the CuO/rGO hybrid can be highly suitable for existing and future gas sensors used for domestic and industrial safety.

The global carbon neutrality challenge places a spotlight on forests as carbon sinks. However, greenhouse gas (GHG) balances of wood for material and energy use often reveal GHG emission savings in comparison with a non-wood reference. Is it thus better to increase wood production and use, or to conserve and expand the carbon stock in forests? GHG balances of wood products mostly ignore the dynamics of carbon storage in forests, which can be expressed as the carbon storage balance in forests (CSBF). For Germany, a CSBF of 0.25 to 1.15 t CO2/m³ wood can be assumed. When the CSBF is integrated into the GHG balance, GHG mitigation substantially deteriorates and wood products may even turn into a GHG source, e.g. in the case of energy wood. Here, building up the forest carbon sink would be the better option. We conclude that it is vital to include the CSBF in GHG balances of wood products if the wood is extracted from forests. Only then can GHG balances provide political decision-makers and stakeholders in the wood sector with a complete picture of GHG emissions.

The response of a single tin oxide nanowire was collected at different temperatures to create a virtual array of sensors working as a nano-electronic nose. The single nanowire, acting as a chemiresistor, was first tested with pure ammonia and then used to determine the freshness status of trout fish (Oncorhynchus mykiss) in a rapid and non-invasive way. The gas sensor reacts to total volatile basic nitrogen, detecting the freshness status of the fish samples in less than 30 seconds. The sensor response at different temperatures correlates well with the total viable count (TVC), demonstrating that it is a good (albeit indirect) way of measuring the bacterial population in the sample. The nano-electronic nose is able to classify the samples according to their degree of freshness, but also to quantitatively estimate the concentration of microorganisms present. The system was tested with samples stored at different temperatures, managing to classify them perfectly (100%) and estimating their log(TVC) with an error lower than 5%.

Salvia ceratophylloides (Ard.) is an endemic, rare, threatened plant species recently rediscovered in very few individuals in two different sites of South Italy. The study of within-plant variation more than among-plant one is fundamental to understand the plant adaptation to the local conditions, especially in rare species, and consequently to preserve plant biodiversity. Here, we reported the variation of the morpho-ecophysiological and metabolic traits between the sessile and petiolate leaf of S. ceratophylloides plants in two different sites for understanding the adaptation strategies for surviving in these habitats. The S. ceratophylloides individuals exhibited different net photosynthetic rate, maximum quantum yield, light intensity for the saturation of the photosynthetic machinery, stomatal conductance, transpiration rate, leaf area, fractal dimension and some VOCs between the different leaf types. This within-plant morpho-physiological and metabolic variation was depended on the site. These results provide empirical evidence of sharply within-plant variation of the morpho-physiological traits and VOCs profiles in S. ceratophylloides which could be because of adaptation to the local conditions.

In this paper, we have numerically investigated a metasurface based perfect absorber design established on the impedance matching phenomena. The paper comprises of two parts. In the first part, the device performance of the perfect absorber is studied which is composed of a silicon Nano-cylindrical meta-atoms periodically arranged on the thin gold layer. The device design is unique which works for both x-oriented and y-oriented polarized light, besides independent of the angle of incidence. In the second part of the paper, CO2 gas sensing application is explored by depositing a thin layer of functional host material polyhexamethylene biguanide polymer on the metasurface. The refractive index of the host material decreases due to the absorption of the CO2 gas. As a result, the resonance wavelength of the perfect absorber performs a prominent blueshift. With the help of the proposed sensor design based on metasurface, the CO2 gas concentration range of 0-524 ppm is detected. The maximum sensitivity of ~17.3 pm/ppm is acquired for the gas concentration of 434 ppm. The study presented in this work explores the opportunity of utilizing metasurface perfect absorber for gas sensing applications by employing the functional host materials.

Greenhouse Gases (GHG) emissions from dairy farms are significant contributors to global warming. However much of the published work on GHG reduction is focused on either Methane (CH4) or Nitrous Oxide (N2O), with few, if any, considering the interactions that changes to farm systems can have on both gases. This paper takes the raw data from a year of activity on a 300 cow commercial dairy farm in Northern Ireland to more accurately quantify the GHG sources by use of a simple predictive model based on IPCC methodology. Differing herd management policies are examined together with the impact of integrating Anaerobic Digestion (AD) into each farm system. Whilst significant success can be predicted in capturing CH4 and Carbon Dioxide (CO2) as biogas and preventing N2O emissions, gains made can be lost in a subsequent process negating some or all of the advantage. The process of extracting value from the captured resource is discussed in the light of current farm parameters together with indications of other potential revenue streams. However, this study has concluded that despite the significant potential for GHG reduction, there is little incentive for widespread adoption of manure based farm scale AD in the UK at this time.

Eysenhardtia platycarpa (Fabaceae) is a medicinal plant used in México and it lacks biotechnological studies for its use. The aim of this work was to establish a cell suspension cultures (CSC) of E. platycarpa, determine the phytochemical profile, and evaluate its antifungal activity. Friable callus and CSC were established with 2 mg/L 1-naphthaleneacetic acid plus 0.1 mg/L kinetin. The highest total phenolics of CSC was 15.6 mg GAE/g dry weight and the total flavonoids content ranged from 56.2 to 104.1 µg QE/g dry weight. CG‒MS analysis showed that the dichloromethane extracts of CSC, sapwood and heartwood have a high amount of hexadecanoic acid (22.3 ‒ 35.3 %) and steroids (13.5 ‒ 14.7%). Heartwood and sapwood defatted hexane extracts have the highest amount of stigmasterol (≈ 23.4%) and β-sitosterol (≈ 43%), and leaf extracts presented β-amyrin (16.3%). Methanolic leaves extracts showed mostly sugars and some polyols, mainly D-pinitol (74.3%). Dichloromethane and fatty hexane extracts of CSC exhibited the percentages inhibition higher for Sclerotium cepivorum with 71.5 and 62.0%, respectively. The maximum inhibition for Rhizoctonia solani was with fatty hexane extracts of the sapwood (51.4%). Our study suggest that CSC extracts could be used as a possible complementary alternative to synthetic fungicides.

The formation of sinkholes in Winkler County, Texas is concerning due to the amount of oil and gas infrastructure and the potential for catastrophic losses. Evidences of new and potential sinkholes have been documented, and determining the cause of these sinkholes is paramount to mitigate the devastating consequences thereof. Studies shown that the Wink sinkholes result from both natural and anthropogenic influences. Data depicting land-cover changes, alterations in the hydrologic systems, climate changes, and oil and gas activity were analyzed in an effort to better understand the link between these processes and sinkhole formation. Results indicate that the combination of these processes lead to the current state; Land cover changes were highest in shrub versus grasses, undeveloped to developed and croplands. Rises in temperature and a decrease in precipitation indicate a shift towards a more arid climate. Changes to the hydraulic system are a direct result of these land cover changes while the groundwater quality depict an environment prone to dissolution. Historical oil and gas activities have created pathways of meteoric water infiltration to the underlying limestone and evaporite formation. The combination of these processes create an environment that accelerates sinkhole formations. Understanding these processes allows for the development and implementation of better land practices, better groundwater protections, and the need for monitoring and maintaining aging oil and gas infrastructure.

The vegan diet excludes animal-derived products consumption. The objective of the present study is to analyze dietary lipid intake, nine plasmatic fatty acids concentrations (from C14:0 [lauric acid] to C20:4 [arachidonic acid]), and conventional clinical lipid profile among vegan individuals with omnivore controls. A case-control and cross-sectional study was performed between 2016 and 2017. Vegans were paired in a 1:1 ratio with omnivores from Merida, Mexico. A 150-item Semi-Quantitative Food Frequency Questionnaire was conducted to evaluate eating patterns. Serum fatty acids were determined from total blood with a gas chromatography assay. Lower cholesterol, stearic, arachidonic and trans fatty acids intake, but higher consumption of lauric acid were observed in the vegan group (p= <0.001, 0.014, <0.001, 0.005, respectively). Decreased plasma concentrations of stearic, arachidonic and linoleic acids were found (p= 0.017, <0.001 and 0.026, respectively). Following a vegan diet for more than three years generate modifications in serum concentrations of saturated and polyunsaturated ω-6 fatty acids, which could lower inflammatory markers’ biosynthesis. Potential benefits regarding cardiovascular risk may be assumed in favor of vegan individuals.

Instead of simplified steady-state models, with modern computers, one can solve the complete aero-thermodynamics happening in gas turbine engines. In the present article, we describe a mathematical model and numerical procedure to represent the transient response of a PT6A gas turbine engine operating at off-design conditions. The aero-thermal model consists of a set of algebraic and ordinary differential equations that arise from the application of the mass, linear momentum, angular momentum, and energy balances in each engine's component. The solution code has been developed in Matlab-Simulink using a block-oriented approach. Transient simulations of the PT6A engine start-up have been carried out by changing the original Jet-A1 fuel with biodiesel blends. Time plots of the main thermodynamic variables are shown, especially those regarding the structural integrity of the burner. Numerical results have been validated against reported experimental measurements and GasTurb simulations. The computer model has been capable to predict acceptable fuel blends, such that the real PT6A engine can be substituted to avoid the risk of damaging it.

Modern gas turbines firing temperatures (1500-2000K) are well beyond the maximum allowable blade material temperatures. Continuous safe operation is made possible by cooling the HP turbine first stages -nozzle vanes and rotor blades- with a portion of the compressor discharge air, a practice that induces a penalty on the cycle thermal efficiency. Therefore, a current issue is to investigate the real advantage, technical and economical, of raising maximum temperatures much further beyond current values. In this paper, process simulations of a gas turbine are performed to assess HP turbine first-stage cooling effects on cycle performance. A new simplified and properly streamlined model is proposed for the non-adiabatic expansion of the hot gas mixed with the cooling air within the blade passage, which allows for a comparison of several cycle configurations at different TIT (turbine inlet temperature) and max (total turbine expansion ratio) with a realistically acceptable degree of approximation.. The calculations suggest that, at a given max, the TIT can be increased in order to reach higher cycle efficiency up to a limit imposed by the required amount and temperature of the cooling air. Beyond this limit, no significant gains in thermal efficiency are obtained by adopting higher max and/or increasing the TIT, so that it is convenient in terms of cycle performance to design at lower rather than higher max. The small penalty on cycle efficiency is compensated by lower plant cost. The results of our model agree with those of some previous much more complex and computationally expensive studies, so that the novelty of this paper lies in the original method adopted on which the proposed model is based, and in the fast, accurate and low resource intensity of the corresponding numerical procedure: all advantages that can be crucial for industry needs. The presented analysis is purely thermodynamic, with no investigation on the effects of the different configurations on plant costs, so that future work addressing a thermo-economic analysis of the air-cooled gas turbine power plant is the next logical step.

Hydraulic fracturing is the most effective method of stimulation for hydrocarbon reservoirs. However the use of water-based fracturing fluids, can be a problem in water-sensitive formations due to the permeability damage hazard caused by clay minerals swelling. For this reason, the foamed fracturing fluids with addition of natural, fast hydrating guar gum were examined. The rheology and filtration coefficients of foamed fracturing fluids were examined and compared to the properties of conventional water-based fracturing fluid. Laboratory results provided the input for numerical simulation of the fractures geometry for water-based fracturing fluids and 50% N₂ foamed fluids. The results show, that the foamed fluids were able to create shorter and thinner fractures compared to the fractures induced by the non-foamed fluid. The simulation proved that the concentration of proppant in the fracture and its conductivity are similar or slightly higher when using the foamed fluid. Moreover such fluids are able to significantly reduce the amount of water necessary for fracturing treatments, limiting clay minerals swelling, and reducing the reservoir permeability damage. The foamed fluids, when injected to the reservoir, provide additional energy, that allow for more effective flowback, and maintain the proper fracture geometry and proppant placing. The results of laboratory work in combination with the 3D simulation showed, that the foamed fluids have suitable viscosity which allows opening the fracture, and transport the proppant into the fracture, providing successful fracturing operation.

To estimate The potential inventory of natural gas hydrates in the Levant Basin we correlated the gas hydrate stability zone (GHSZ), modeled with locally estimated thermodynamic parameters, with seismic indicators of gas. Compilation of oceanographic measurements define the deep-water temperature and salinity to 13.8°C and 38.8‰ respectively, predicting the top GHSZ at a water depth of 1250±5 m. Assuming beneath the seafloor a hydrostatic pore-pressure, the water body salinity, and geothermal gradients ranging between 20 to 28.5°C/km, yields a useful first-order base-GHSZ approximation. Our model predicts that the entire northwestern half of the Levant Basin lies within the GHSZ, with a median thickness of ~150 m. High amplitude seismic reflectivity (HASR) imaged on an extensive 3D seismic dataset, consistently correlates with verified active seafloor gas seepage and is pervasively distributed across the deep-sea fan of the Nile within the Levant. Two main trends observed for the distribution of HASR are suggested to represent: (1) shallow gas and possibly hydrates, within buried channel-lobe systems 25 to 100 m beneath the seafloor; and (2) a regionally discontinuous bottom simulating reflection (BSR) broadly matching the modeled base GHSZ. We therefore estimate the potential methane hydrates reserve within the Levant Basin at ~4 Tcf.

The recent growing attention to energy saving and environmental protection issues has brought to attention the possibility of exploiting syngas from gasification of biomass and coal for the firing of industrial plants included the so called Integrated Gasification Combined Cycle ones. In order to improve the knowledge about the employ of syngas in lean premixed turbulent flames, a large scale swirl stabilized gas-turbine burner has been operated with a simplified model of H₂ enriched syngas from coal gasification. The experimental campaign has been performed at atmospheric pressure with operating conditions derived from scaling the real gas turbines ones. The results are here reported and consist of OH-PLIF measurements carried out at decreasing air equivalence ratio conditions and are analysed together with the mean aerodynamic characterisation of the burner flowfield in isothermal condition. The OH concentration distributions have been analysed statistically in order to obtain information about the location of the most reactive zones and an algorithm has been applied to the data in order to identify the flame fronts. In addition, the flame front locations have been successively interpreted statistically in order to obtain information about their main features and about their dependence on the air to fuel ratio behaviour.

Abstract: The recent growing attention to energy saving and environmental protection issues has brought to attention the possibility of exploiting syngas from gasification of biomass and coal for the firing of industrial plants included the so called Integrated Gasification Combined Cycle ones. In order to acquire a detailed knowledge about the behaviour of lean turbulent premixed flames, the present work resent the results of an experimental characterisation of a prototypical gas turbine burner operated at atmospheric pressure at condition scaled from real gas turbines ones. The results here presented derive from OH-PLIF measurements carried out at decreasing air equivalence ratio conditions and are analysed together with a mean aerodynamic characterisation of the burner operating in isothermal condition. The OH concentration distributions have been analysed statistically in order to obtain information about the location of the most reactive zones and an algorithm has been applied to the data sets in order to identify the flame fronts. In addition, the flame front locations have been successively interpreted statistically in order to obtain information about their main features and about their dependence on the air to fuel ratio behaviour.

Vanadium titano-magnetite is a significant resource in China, and in this study, we characterize its isothermal reduction mechanisms in the mixture of H₂, CO, and N₂ where the variables considered here include reduction time, reduction temperature, gas composition, and pellet size. The kinetics of the reduction process are mainly studied, which follows a shrinking core model. The results indicate that the reduction degree of oxidized VTM pellets increases with the increase of reduction time, reduction temperature but decreases with the increase of pellet size. Moreover, we found that an increase of H₂/(H₂+CO) ratio induces an increase of the reduction degree. Then the transformation of main Ti-bearing mineral phases is discussed, and the most probable reaction mechanism is revealed. In the whole reduction process, the kinetic results confirm the existence of an early stage and a latter stage, which are controlled by interface chemical reaction and diffusion, respectively. Furthermore, the results show that the diffusion-control step can be observably shortened with the decrease of pellet size because a thinner product layer is formed during the reduction process. Our study thus provides a valuable technical basis on the VTM industrial application.

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines to turbofan with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving propulsive performance. The BMT 120 KS micro turbojet engine is selected for performance evaluation of the conversion process using gas turbine performance software, GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis carried out, an improvement in the converted micro gas turbine engine performance in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, fan speed operation may be adjusted independently of the core, allowing increased thrust generation or better fuel consumption. Therefore, enabling a wider gamut of operating conditions and enhances the performance and scope of tactical UAV.

Considering the high potential of hydrogen (H₂) as a clean energy carrier, the implementation of high performance and cost-effective biohydrogen (bioH₂) purification techniques is of vital importance, particularly in fuel cell applications. In this context, membrane technology is a potentially energy-saving solution to obtain high-quality biohydrogen. The most promising poly(ionic liquid) (PIL) - ionic liquid (IL) composite membranes previously studied by our group for CO₂/N₂ separation, containing pyrrolidinium-based PILs with fluorinated or cyano-functionalized anions, were chosen as starting point to explore the potential of PIL–IL membranes for CO₂/H₂ separation. The CO₂ and H₂ permeation properties at the typical conditions of biohydrogen production (T =308 K and 100 kPa of feed pressure) were measured and discussed. PIL–IL composites prepared with [C(CN)₃]^– anion showed higher CO₂/H₂ selectivities and H₂ diffusivities compared to those containing [NTf₂]^– anion. All the membranes revealed CO₂/H₂ separation performances above the upper bound for this specific separation, highlighting the composite incorporating 60 wt% of [C₂mim][C(CN)₃] IL.

Essential oils are mixtures of compounds obtained from plants, including flowers, roots, bark, leaves, seeds,peel, fruits, wood, that have risen up in the last decades thanks to their beneficial properties as antibacterial, antifungal and anti-inflammatory agents. The aim of this study was to characterize and analyze 13 different commercial essential oils with two different techniques. The first is GC-MS, coupled with SPME, thanks to which 204 different VOCs have been identified. The results show that a total of 95 compounds was found only in one oil, while the others were found with different frequencies in many of them. The most represented class is that of terpenes, as widely reported in literature. The second technique is based on an array of chemical gas sensors. This system was used to investigate whether sensors are able to identify these products. It turned out that basil, cinnamon and carnation are the most identifiable oils with different number and typology of sensors, especially tin oxide and copper oxide nanowires, while cayeput and thyme are more mistakable samples. Thanks to this detailed study, it has been possible to reach and obtain novel insights for the future development of this type of research.

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO₂ with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.

In reservoir engineering, one of the main sources of information for the characterization of reservoir and well parameters is well testing. Among the unconventional well testing methodologies, Harmonic Well Testing (HPT) is appealing from an economic standpoint because it could provide well performance and reservoir behavior monitoring without having to interrupt field production. Recorded pressure analysis is performed in the frequency domain by adopting a derivative approach similar to conventional well testing. To this end, pressure and rate data must be decomposed into harmonic components. Test interpretability can be significantly improved if pressure data are detrended prior to interpretation, filtering out non periodic events such as discontinuous production from neighboring wells and flow regime variations which did not respect the designed test periodicity. Therefore, detrending offers the possibility of overcoming the limitation of HPT applicability due to the difficulty of imposing a regularly pulsing rate for the whole test duration (typically lasting several days). This makes HPT attractive for well performance monitoring, especially in gas storage fields. In this paper, the application of different detrending methodologies to synthetic HPT pressure data generated in different reservoir and operational scenarios is presented and discussed. Moreover, a real case application is also presented.

This paper proposes a method based on genetic algorithm (GA) for the security-constrained optimal dispatch of integrated natural gas and electricity networks, considering operating scenarios in both energy systems. The mathematical formulation of the optimization problem consists of a multi-objective function which aims to minimize both cost of thermal generation (diesel and natural gas) as well as the production and transportation of natural gas. The joint gas-electricity system is modeled by two separate groups of nonlinear equation, which are solved by the combination of Newton's method with the GA. The applicability of the proposed method is tested in the Belgian gas network integrated with the IEEE 14-bus test system and a 15-node natural gas network integrated with the IEEE 118-bus test system. The results demonstrate that the proposed method provides efficient and secure solutions for different operating scenarios in both energy systems.

Systemic lupus erythematosus (SLE) is a chronic autoimmune disorder characterized by widespread inflammation and multi-organ damage. Toll-like receptor 7 (TLR-7) and autophagy have been implicated in SLE pathogenesis. Rice husk silica liquid (RHSL) has shown potential for modulating inflammatory responses, but its effects on SLE have not been thoroughly investigated. This study aims to evaluate the impact of RHSL on immune responses and autophagy in an in vitro model of SLE, focusing on its effects on TLR-7 signaling, cytokine production, and autophagy modulation. RAW264.7 cells and human peripheral blood mononuclear cells (PBMCs) from healthy donors and SLE patients were used. Cells were stimulated with LPS or TLR-7 agonists and treated with RHSL. Cell viability was assessed, and cytokine levels (TNF-α and IL-6) were measured by ELISA. Autophagy-related proteins (LC3II, ATG5-ATG12) were analyzed by Western blotting. The effect of autophagy inhibition was studied using 3-methyladenine (3-MA). RHSL did not affect cell viability but significantly reduced TNF-α production in LPS- and TLR-7 agonist-stimulated RAW264.7 cells and PBMCs. RHSL enhanced autophagy, as evidenced by increased LC3II and ATG5-ATG12 conjugation in both RAW264.7 cells and SLE patient-derived PBMCs. The reduction in TNF-α production by RHSL was attenuated by 3-MA, indicating that autophagy plays a role in this process. RHSL also inhibited the translocation of phosphorylated NF-κB into the nucleus, suggesting a mechanism for its anti-inflammatory effects. RHSL exhibits potential as an immunomodulatory agent in SLE by enhancing autophagy and modulating TLR-7 signaling pathways. These findings suggest that RHSL could offer therapeutic benefits for managing inflammatory responses in SLE and warrant further investigation into its clinical applications.

This article presents the theoretical study, numerical simulation and the fabrication of a phase shifter and stub resonator in microstrip ridge gap waveguide (MGCW) technology with the use of liquid crystal (LC) in its substrate as a reconfigurable material. The phase shifter and the stub resonator are filled with LC and thanks to LC's dielectric anisotropy properties, the phase shift and resonance response can be easily controlled using an external electric or magnetic bias field. The phase shifter was designed to operate in the range of 10 to 20 GHz and the resonator was designed to operate in the range of 7.8 to 8.8 GHz. The phase shifter's insertion losses, associated with both parallel and perpendicular LC's permittivity, as well as the phase response were computed and measured. Finally, the figure of merit (FoM) was extracted. The resonator's frequency response, associated with both parallel and perpendicular LC's permittivity, was computed. The resonator's frequency responses, provided different polarization voltages, were measured and compared to the simulation results. The technological issues were discussed. The good agreement between simulation and measurement results establishes this technology as a viable approach to the development of RF reconfigurable devices.

Gastric cancer (GC) is a major cause of cancer-related mortality worldwide, often associated with a bad prognosis because of its asymptomatic phenotype until advanced stages, highlighting the need for its prevention and early detection. GC development is preceded by gastric preneoplasia lesions (GPNL), namely atrophic gastritis (AG), intestinal metaplasia (IM), and dysplasia (DYS). GC is currently diagnosed by endoscopy, which is invasive and costly and has limited effectiveness for the detection of GPNL. Therefore, the discovery of non-invasive biomarkers in liquid biopsies, such as blood samples, to identify the presence of gastric preneoplasia and/or cancer lesions at an asymptomatic stage, is of paramount interest. This comprehensive review provides an overview of plasma/serum proteins recently identified and their diagnostic performance for the prediction of GPNL and early cancer lesions. Autoantibodies appear as promising biomarkers for AG, IM and early gastric cancer detection, along with inflammation and immunity-related proteins and antibodies against H. pylori virulence factors. There is a lack of specific protein biomarkers to detect DYS. Despite the need for further investigation and validation, some emerging candidates could pave the way to develop reliable, non-invasive diagnostic tests for the detection and prevention of GC.

A two-stage pilot plant study has been completed that evaluated the performance of a reverse osmosis (RO) membrane process for the treatment of a feedwater that consisted of a blend of nanofiltration (NF) concentrate and brackish groundwater. Membrane performance was assessed by monitoring the process operation, collecting water quality data, and documenting the blended feedwater’s impact on fouling due to a combination of, or solely caused by, plugging, scaling, microbiological, or organic means. Fluorescence and biological activity reaction tests were used to identify the types of organics and microorganisms present in the blended feedwater. Additionally, scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS) were used to analyze suspended matter that collected on the surfaces of cartridge filters used in the pilot’s pretreatment system. SEM and EDS were also used to evaluate solids collected on the surfaces of 0.45-µm silver filter pads after filtering known volumes of NF concentrate and RO feedwater blends. Water quality analyses confirmed that the blended feedwater contained little to no dissolved oxygen, and the blended feedwater was absent of a significant amount of particulate matter as defined by silt density index and turbidity measurements. However, water quality results suggested that the presence of sulfate, sulfide, iron, anaerobic bacteria, and humic acid organics likely contributed to the formation of pyrite observed on some of the membrane surfaces autopsied at the conclusion of pilot operations. It was determined that first-stage membrane productivity was impacted by the location of cartridge filter pretreatment; however, second-stage productivity was maintained with no observed flux decline during the entire pilot operation’s timeline. Study results indicated that the operation of an RO process treating a blend of NF concentrate and brackish groundwater could maintain a sustainable and productive operation that provided a practical zero-discharge process operation while the dilution of RO feedwater salinity would lower overall production costs.

Hydrogen gas (H2) has attracted attention as a next-generation clean energy source. Its efficient and safe preparation and utilization are crucial in both industry and organic chemistry. In this study, a Pt/CB-catalyzed MW-mediated continuous-flow hydrogenation reaction was developed using methylcyclohexane (MCH) as the reducing agent (hydrogen carrier). Alkynes, alkenes, nitro groups, benzyl esters, and aromatic chlorides were chemoselectively hydrogenated using Pt/CB under MW-assisted continuous-flow conditions. This methodology represents a safe and energy-efficient hydrogenation process, as it eliminates the need for an external hydrogen gas supply or heating jackets as a heat medium. Further application of MW-mediated continuous-flow hydrogenation reactions is a viable method for the efficient generation and utilization of sustainable energy.

Sheep’s milk is a significant source of nucleotides monophosphate (NMPs) but can also contain undesirable residues from veterinary drugs, posing a potential human health risk. This study introduces a novel application of 2D-LC, in heart-cutting mode, for the simultaneous determination of nucleotides and veterinary drug residues in sheep’s milk. Two-dimensional liquid chromatography (2D-LC) allows for the separation of these compounds in a single chromatographic run despite their differing physicochemical properties. The proposed method separates six veterinary drug residues and five NMPs in a single injection. The compounds were separated using a C18 reversed-phase column in the first dimension and a Primesep SB analytical column in the second dimension. The method performance was evaluated in terms of linearity range, detection and quantification limits, matrix effects, precision, and accuracy. The results demonstrated good linearity and sensitivity, with quantification limits allowing for the quantification of veterinary drugs at the maximum residue level and nucleotides at typical levels found in milk samples. The method has been successfully applied to the analysis of sheep’s milk samples acquired from local supermarkets, with recoveries within a range of 70-119 % and 82-117 % for veterinary residues and NMPs, respectively.

Between a vineyard and the foliage wall of an adjacent forest, 25 traps containing different Drosophila attractants were applied on three occasions in autumn after the grape harvest. The attractant liquid was Pinot Blanc grape juice to which pure Saccharomyces cerevisiae yeast had been added to initiate fermentation. The five test variants differed in only one characteristic, namely the fermentation time, which was changed in two-day steps. Nine species of the genus Drosophila were captured, but only two were abundant enough to allow statistical analysis of variant differences in capture frequencies. Both species, D. suzukii and D. simulans, can affect the quality of the berries and ultimately the wine even before the harvest and are therefore considered pests. The studies showed that fermenting grape juice is significantly more attractive to both species than unfermented grape juice and that the attractiveness of the attractant liquid is maximised for D. simulans males with a fermentation time of seven to eight days.Parallel to this experiment, an analysis of the aroma spectrum of the fermenting grape juice was carried out with a temporal resolution of one day for the first twenty days. This made it possible to identify the aroma substances that had the highest concentrations in the time frame in which the attractant was particularly attractive and whose attractant effect should therefore be investigated further.

The generalized dynamic model of the rotor system, presented in the paper, is the first model that takes into account the interconnected oscillations of the “rotor - weakly conductive fluid – foundation” system under the action of such parameters as fluid and rotor motion, linear eccentricity, friction forces, foundation vibration and nonlinear characteristics of rolling bearings, as well as the action of a magnetic field on the fluid. Consistent equations of motion for the system “rotor - weakly conductive fluid – foundation” were derived and solved analytically. Forced and natural oscillations of the system were analyzed, and the distinctive features of the rotor system dynamics were revealed. The values of frequencies and amplitudes, which are one of the main factors determining the dynamic behavior of the system, were obtained and studied.

Bisphenol F (BPF) and bisphenol S (BPS) are increasingly used as substitutes for bisphenol A (BPA) in the plastic industry, driven by concerns over the adverse effects of BPA. However, there is a lack of infor-mation on the extent of exposure to these chemicals in children. This study aims to assess the extent of BPA, BPF, and BPS exposure and determine factors that influence such exposure. A group of Thai children (age 6-13 years, n=358) were recruited between October 2019-2020. Two first morning void was collected one week apart. Demographic and exposure-related information was gathered. Urinary concentrations of bisphenols were analyzed by liquid-chromatography and tandem mass spectrometry. Correlation between bisphenol concentrations and various factors was determined using generalized estimating equations with linear model. BPA, BPF, and BPS were detected at 79.6%, 31.0%, and 16.8%, with geometric mean (GM) concentrations of 1.41, 0.013, and 0.014 ng/mL respectively. Younger children aged < 10 years exhibited 1.3-1.6 times higher GM levels of all bisphenols compared to older children. Exposure to food stored in plas-tic containers were associated with higher levels of BPF and BPS. In conclusion, BPA was the most fre-quently detected bisphenol in urine samples from Thai children, followed by BPF and BPS.

: This article reports on polymer (PLLA, poly(L-lactic acid)) nanosheets incorporated with Fe-ion nanoparticles, aiming at using the latter nanoparticles as source to release Fe ions to facilitate burn wound healing when such nanosheets are applied on skin as biomedical tissue. Laser ablation in liquid phase was used to produce Fe-containing nanoparticles that after incorporation into PLLA nanosheets would release Fe ions when in immersed in water. Such nanoparticles prepared in chloroform are shown by XPS to be based on iron chloride and oxide phases. After incorporation into PLLA nanosheets, the ion –release test demonstrated that Fe ions could be released successfully into water at pH 7.4, which implies that such polymer nanosheets show promise for biomedical applications as potential patches for healing burn wounds. Incorporation with two different metal ions (Fe and Zn) is shown to be efficient and both types of ions were demonstrated to be released simultaneously and with comparable release rates.

Abstract: Filipendula ulmaria, commonly known as meadowsweet, is a wild herbaceous flowering plant widely distributed in Europe. A range of salicylic acid derivatives and flavonol glycosides have been previously associated with the antirheumatic and diuretic properties of F. ulmaria. In the present work, an hydroalcoholic extract of F. ulmaria aerial parts was extensively profiled using an efficient NMR-based dereplication strategy. The approach involves fractionation of the crude extract by centrifugal partition chromatography (CPC), ¹³C NMR analysis of the fractions, 2D-cluster mapping of the whole NMR dataset and finally, structure elucidation using a natural metabolite database, validated by 2D NMR data interpretation and liquid chromatography coupled to mass spectrometry. The chemodiversity of the aerial parts was quite broad, with 28 compounds unambiguously identified, belonging to various biosynthetic classes. The F.ulmaria extract and CPC fractions were screened for their potential to improve skin epidermal barrier function and also skin renewal properties using in vitro assays performed on Normal Human Epidermal Keratinocytes. Fractions containing quercetin, kaempferol glycosides, ursolic acid, pomolic acid, naringenin, β-sitosterol, and tellimagrandins I and II were found to be responsible for the up-regulation of genes related to skin barrier function, epidermal renewal and stress responses. This research is significant as it could provide a natural solution for improving hydration and skin renewal properties.

To determine promethazine (PMZ) and its metabolites promethazine sulfoxide (PMZSO) and monodesmethyl-promethazine (Nor1PMZ) in swine muscle, fat, kidney, and liver, a sample preparation and high-performance liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis method were established and validated. The sample was extracted with 0.1% formic acid-acetonitrile, and the extract was purified with acetonitrile-saturated n-hexane. After concentration by rotary evaporation, the extract was re-dissolved in 0.1% formic acid-water and acetonitrile (80:20, v/v). The HPLC-MS/MS column used was a Waters Symmetry C18 (100 mm × 2.1 mm i.d., 3.5 μm), with 0.1% formic acid-water and acetonitrile as the mobile phase, and the target compounds were determined by positive ion scan and multiple reaction monitoring. PMZ and Nor1PMZ were quantified with deuterated promethazine (PMZ-d6) as the internal standard, while PMZSO was quantified by external standard method. The limits of detection (LOD) and limits of quantification (LOQ) of PMZ and PMZSO in muscle, liver, and kidney spiked samples were 0.05 μg/kg and 0.1 μg/kg, respectively, while those of Nor1PMZ were 0.1 μg/kg and 0.5 μg/kg, respectively. The LOD and LOQ of analytes in fat spiked sample were 0.05 μg/kg and 0.1 μg/kg, respectively. The sensitivity of this method reaches or exceeds its presented in previous reports. The analytes PMZ and PMZSO showed good linearity within the range of 0.1 μg/kg to 50 μg/kg, while Nor1PMZ showed good linearity within the range of 0.5 μg/kg to 50 μg/kg, with correlation coefficients (r) greater than 0.99. The recoveries of the target compounds in the sam-ples were between 81.73% and 107.17%, and the precision ranged from 1.78% to 10.47%. This study developed for the first time an HPLC-MS/MS method for the determination of PMZ and its metabolites PMZSO and Nor1PMZ in four swine edible tissues, comprehensively covered target tissues of monitoring object, which is applicable for monitoring veterinary drug residues in ani-mal-derived foods and ensuring food safety.

Iron oxide nanozymes are a form of nanomaterial with both superparamagnetic and enzyme-mimicking properties. Given the multifunctional nature of iron oxide nanozymes, it is attractive for creating iron oxide hybrid nanozymes through biomolecular modifications to imbue with auxillary properties. Such iron oxide hybrid nanozymes can be useful for rapid and cost-effective analysis of circulating tumor nucleic acids (ctNAs) in patient liquid biopsies during minimal residual disease (MRD) monitoring of cancer recurrence. Herein, the use of streptavidin-modified iron oxide hybrid nanozymes is reported for magnetic enrichment and bioelectrocatalytic sensing of three prostate cancer (PCa) ctRNA biomarkers with high detection specificity and sensitivity (10 copies) over an ultrabroad dynamic range (five orders of magnitude). Furthermore, the feasibility of ctRNA analysis for pre- and post-cancer treatment MRD monitoring is demonstrated using PCa urinary liquid biopsy samples.

High circulating concentrations of the gut microbiota-derived metabolite trimethylamine N-oxide (TMAO) are significantly associated with the risk of obesity and type 2 diabetes (T2D). We aimed at evaluating the impact of glycemic control and bariatric surgery on circulating concentrations of TMAO and its microbiota-dependent intermediate, γ-butyrobetaine (γBB), in newly diagnosed T2D patients and morbidly obese subjects. An additional experiment was carried out in eight male C57BL/6J mice fed a Western-type diet for twelve weeks. The strategy for glycemic control in the T2D patients significantly improved the HbA1c concentrations without producing changes in the estimated glomerular filtration rate. However, the plasma TMAO and γBB concentrations were significantly increased following the glycemic control in T2D patients. Bariatric surgery was very effective in reducing weight in obese subjects. Nevertheless, the surgery reduced plasma γBB concentrations without affecting TMAO concentrations and the estimated glomerular filtration rate. Neither diet-induced obesity nor insulin resistance were associated with circulating TMAO and γBB concentrations in mice. Our findings do not support that glycemic control or bariatric surgery improve the circulating concentrations of TMAO in newly diagnosed T2D and morbidly obese patients. The contribution of antidiabetic drugs to gut microbiota composition could explain TMAO elevations in treated T2D subjects.

This work aims to investigate the influence of reaction time and catalyst-to-residual fat ratio by catalytic upgrading from pyrolysis vapors of residual fat at 400 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, and acid value) and chemical composition of bio-oils, over a catalyst fixed bed reactor of activated carbon pellets impregnated with 10.0 M NaOH, in semi pilot scale. The experiments were carried out at 400 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 50, 60, 70, 80, 90, 100 and 120 minutes in order to investigate the process kinetics. The physicochemical properties (density, kinematic viscosity, and acid value) of bio-oils were determined by official methods. The chemical composition of bio-oils determined by GC-MS. The thermal catalytic cracking of residual fat show bio-oils yields from 55.55 to 30.22 (wt.%), aqueous phase yields between 2.83 and 3.19 (wt.%), solid phase yields between 13.56 and 9.75 (wt.%), and gas yields from 27.89 to 55.60 (wt.%). The yields of bio-oil decreases from 74.41 to 30.22% (wt.) with increasing catalyst-to-Tallow kernel oil ratio, while that of gaseous phase increases from 12.87 to 55.60% (wt.). For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of bio-oils decreases as the reaction time increases varying from 0.9266 to 0.8220 g/cm³, 8.10 to 2.24 mm²/s, and 144.14 to 2.37 mg KOH/g. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, ring-containing alkanes, ring-containing alkenes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the pyrolysis and catalytic cracking experiments, the hydrocarbon selectivity in bio-oil increases with increasing reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties density, kinematic viscosity, and acid value were 0.8220 g/cm³, 3.03 mm2/s, and 2.37 mg KOH/g, respectively, with a maximum hydrocarbon concentration of 97.194% (area.) and 2.806% ketones (area.) were obtained at 400 °C and 1.0 atmosphere, 80 minutes, without catalyst. For the catalytic cracking experiments, the maximum hydrocarbon content of 75.763% (area.) and 17.041% (area.) carboxylic acids, 4.702% (area.) ketones (area.), and 2.494% (area.) non-identified oxygenates was obtained at 400 °C and 1.0 atmosphere, 90 minutes, using a catalyst fixed bed reactor, with 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH as catalyst.

Short chain quinones (SCQs) have been identified as potential drug candidates against mitochondrial dysfunction, which is largely dependent on their reversible redox characteristics of the active quinone core. We recently synthesized a SCQ library of > 148 naphthoquinone derivatives and identified 16 compounds with enhanced cytoprotection compared to the clinically used benzoquinone idebenone. One of the major drawbacks of idebenone is its high metabolic conversion in the liver, which significantly restricts is therapeutic activity. Therefore, this study assessed the metabolic stability of the 16 identified naphthoquinone derivatives 1-16 using hepatocarcinoma cells in combination with an optimized reverse-phase liquid chromatography (RP-LC) method. Most of the derivatives showed significantly better stability than idebenone over 6 hours (p < 0.001). By extending the side-chain of SCQs, increased stability for some compounds was observed. Metabolic conversion from the derivative 3 to 5 and reduced idebenone metabolism in the presence of 5 were also observed. These results highlight the therapeutic potential of naphthoquinone-based SCQs and provide essential insights for future drug design, prodrug therapy and polytherapy, respectively.

The early diagnosis of mastitis represents an essential factor for a prompt detection of the animal for further actions. In fact, if not culled, infected cows must be segregated from the milking herd and milked last, or milked with separate milking units. Besides microbiological analysis, the somatic cell count (SCC) commonly used as predictor of intramammary infection, frequently lead to a misclassification of milk samples. To overcome these limitations, more specific biomarkers are continuously evaluated. Total amino acid content increases significantly in mastitic milk compared to normal one. Bovine mastitis can arise as a result of infection of the mammary gland by Staphylococcus aureus. Multiplication of this bacterium within the mammary gland is required for infection to persist. S. aureus requires branched-chain amino acids (BCAAs: isoleucine, leucine, valine) for protein synthesis, branched-chain fatty acids synthesis and environmental adaptation by responding to their availability via transcriptional regulators. The importance of BCAAs for S. aureus physiology necessitates that it either synthesize them or scavenge them from the environment. Increase of BCAAs in composite milk has been postulated to be linked to mammary infection by S. aureus. In the present work, we demonstrated, by a direct ion-pairing reversed-phase method based on the use of the evaporative light-scattering detector (IP-RP-HPLC-ELSD), applied to 65 composite cow milk samples, a correlation between the concentration of isoleucine and leucine and S. aureus load.

Deformation of the surface of diamagnetic liquid by magnetic field is called the “Moses Effect”. Physics and applications of the direct and inverse Moses effects are reviewed. Experimental techniques enabling visualization of the effects are surveyed. Impact of magnetic field on micro- and macroscopic properties of liquids is addressed. Influence of the surface tension on the shape of the near-surface dip formed in a diamagnetic liquid by magnetic field is reported. Floating of diamagnetic bodies driven by the Moses effect is treated. The effect of the “magnetic memory of water” in its relation to the Moses Effect is discussed. The dynamics of self-healing of near-surface dips due to the Moses Effect is considered.

The release profiles of methotrexate, an anticancer drug, from the monoolein liquid crystalline cubic phases were studied. The cubic phases were used either in the form of a lipidic film deposited onto a glassy carbon electrode surface or in the dispersed form of magnetocubosomes, which are considered a prospective hybrid drug delivery system. Commonly, cubosomes or liposomes are employed, but not in the case of toxic methotrexate, known to block receptors responsible for folate transport into the cells. The release profiles of the drug from the lipidic films were monitored electrochemically and described using the Higuchi model. They were also modified via changes in temperature; the release was faster, although deviating from the model when the temperature was increased. Magnetocubosomes - cubic phase nanoparticles containing hydrophobic magnetic nanoparticles placed in an alternating magnetic field of low frequency and amplitude, stimulated drug release from the suspension, which was monitored spectroscopically. These new biocompatible hybrid materials are very promising, allowing to control the release of the drug at the appropriate sites, but do require further investigations into their in vitro cytotoxicity and in vivo biodistribution.

Spherical microparticles of TiO₂ were synthesized by the ionic liquid-assisted solvothermal method at different reaction time (3, 6, 12 and 24h). The properties of the prepared photocatalysts were investigated by means of UV-vis diffuse-reflectance spectroscopy (DRS), BET surface area measurements, scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), and X-ray photoelectron spectroscopy (XPS). The results indicated that the efficiency of phenol degradation was related with a time of the solvothermal synthesis as determined for TiO₂_EAN(1:1)_24h sample. Microparticles of TiO₂_EAN(1:1)_3h formed during the only 3h of synthesis time revealed really high photoactivity under visible irradiation – 75%. This value increased to 80% and 82% after 12h and 24h, respectively. The photoactivity increase was accompanied by the increase of the specific surface area thus pores size, as well as ability to absorb UV-vis irradiation. The high efficiency of phenol degradation of IL-TiO₂ photocatalysts was ascribed to the interaction between the surface of TiO₂ and ionic liquid components (carbon and nitrogen).

Circulating tumor cells (CTC) have shown to be prognostic in advanced colorectal cancer (advCRC), but their value for predicting response to treatment or as a source of molecular data is debated. We compared CellSearch® (Janssen Diagnostics, LLC) and IsoFlux^TM (Fluxion Biosciences Inc, South San Francisco, CA) systems for the enumeration of CTC in patients with newly diagnosed advCRC (group 1; n=34). Using castPCR^TM we studied KRAS status in CTC isolated with IsoFlux^TM and compared it with that of the primary tumor in patients from group 1 and in KRAS wild-type (KRAS^WT) patients with progressive disease (group 2; n=22). Median number of CTC detected with CellSearch® (groups 1 and 2) was 1 (range: 0-78) and with IsoFlux^TM (group 1) was 8 (range: 0-419), showing a modest correlation (r=0.345, P=0.036), which improved if lung metastases (r=0.805, P=0.016) or if lung and liver metastases were present (r=0.812, P=0.05). A Bland-Altman plot showed that the higher the number of CTC detected the larger the difference between both methods in favor of IsoFlux^TM. After a median follow-up since CTC collection of 16 months (range: 1-30) CellSearch® ≥ 3 CTC (HR 2.77, 95% CI 0.77-9.95) and IsoFlux^TM ≥ 11 CTC (HR 4.14, 95% CI 1.05-16.19) were established as the best cutoff points for predicting survival. Using castPCR^TM we found KRAS mutations in CTC in 4 out of 8 patients from group 1 and in 2 out of 3 patients from group 2. None of these mutations were found in the primary tumor using standard methods, possibly reflecting intratumor heterogeneity or treatment selection pressure. We conclude that IsoFlux^TM is more efficient than CellSearch® in the isolation of CTC in patients with advCRC, achieving, in a majority of cases, the established minimum of CTC for castPCR^TM-based genetic analyses.

Soil carbon (C) cycling under anoxic conditions is mechanistically linked to dissimilatory iron (Fe) reduction, which could be regulated by exogenous dissolved organic matter (DOM). However, the impact of complex exogenous DOM on soil microbial activity and C-Fe coupling in paddy soils remains underexplored. With a 100-day microcosm experiment, we determined that the molecular composition of DOM derived from organic fertilizers and biochar on paddy soil affects soil microbial community, Fe reduction, and C emissions. Our results indicated that biochar-DOM significantly promoted Fe reduction and accelerated CH₄ and CO₂ emissions, and organic manure-DOM increased soil CO₂ emissions, which was closely related to the molecular composition of exogenous DOM. DOM molecules with high aromaticity (AI_mod) and high DBE, including lignins-vascular plant-derived polyphenols, lignins-polycyclic aromatics (PA), and condensed aromatics-PA, promoted soil Fe reduction and CH₄ emissions by enriching soil Fe-reducing bacteria (FeRB), reducing methanotrophs, and facilitating r-strategists at the early stage of incubation. Conversely, DOMs with low AI_mod, low DBE and high H/C, such as lignins-highly unsaturated and phenolic compounds and proteins-aliphatic compounds, enhanced CO₂ emissions by facilitating recalcitrant C degradation and CH₄ oxidation at the late stage of incubation. In conclusion, our study highlights the importance of the molecular composition of DOMs derived from organic amendments in regulating soil Fe reduction and C emissions. The findings offer novel insights into the effective utilization of agricultural resources and the mitigation of soil C emissions.

The construction of tall buildings generates a high spatial and temporal concentration of greenhouse gas (GHG) emissions. Research studies have shown that as building height increases, more resources per floor area are required to withstand the increasing effects of lateral loads (wind and earthquake). This has major implications for the environmental performance of tall buildings since the Embodied GHG Emissions (EGHGE) of structural systems tend to represent the greatest portion of the life cycle GHG emissions of tall buildings. This study presents a data driven-based approach for decarbonization of tall buildings and evaluates the significant impact of material types (concrete, steel, and timber), concrete strength, and structural systems relative to a building's height on the EGHGE associated with tall buildings. In mitigating the effects of climate change, this research implements machine learning (ML) algorithms as an early-stage design tool to facilitate the choice of materials, and structural systems for tall buildings. This work considers a wide range of high-rise buildings with four different types of lateral structural systems (Braced-Frame system, Outrigger-Belt system, Shear Wall system, and Tubular system), four different types of construction materials (concrete, steel, hybrid, and timber), varying heights (ranging from 10 to 100 stories), and various concrete materials with different compressive strength ranging from 32 to 90 MPa. Data gathered from more than 100 existing tall building projects along with the data obtained from finite element analysis of 120 high-rise buildings models were utilized to train various ML regression algorithms: Decision Tree, Support Vector Machine, Polynomial Regression, and Elastic-Net Regularized Regression. The performance of ML models was carefully assessed, and the best prediction model was selected to estimate the total amount of CO2 emissions for high-rise buildings. Results indicate that hybrid structures with the Out-Rigger-Belt system exhibit the lowest carbon emission (110 kg/m2) compared to other structural types and systems.

It is imperative to conduct experimental studies on the seepage behavior of gas-bearing coal under cyclic dynamic loading conditions. This paper focuses on the evolution of coal permeability under the combined effects of dynamic loading, static loading, and gas adsorption. The principal conclusions are as follows. (1) As the frequency and amplitude of dynamic loading increase, the development of pore and fissure structures within the coal body becomes increasingly pronounced during dynamic loading cycles, resulting in a gradual rise in permeability. Notably, as the coal approaches its yielding stage, the permeability can increase by up to 47%. (2) The permeability curve is divided into four regions: the compaction reduction zone, the oscillation zone, the gradual recovery zone, and the abrupt increase zone of failure. Ultimately, in the failure phase, the permeability surges dramatically, potentially reaching 4 to 5 times the initial permeability. (3) When the static load stage is constant, the rate of change in permeability of the coal under dynamic loading decreases with increasing adsorption amount. When the adsorption amount is constant, the rate of change in permeability of the coal under dynamic loading increases with the increase in static load stress stage, with the maximum increase reaching 75.2%. It can be concluded from the rate of change in permeability and the dynamic loading sensitivity coefficient that the permeability of the coal is highly sensitive to cyclic dynamic loading, with increased sensitivity associated with larger static load stages and decreased sensitivity with greater adsorption amounts.

Membrane gas absorption technology has been considered as a promising approach to mitigate CO2 emissions from power plants. The aim of this study is to evaluate the environmental impacts of CO2 absorption and desorption processes by hollow fiber membrane contactors using life cycle assessment methodology. On the basis of ReCipe 2016 Midpoint and ReCipe 2016 Endpoint methods, the research results show that, membrane gas absorption system exhibits the lowest environmental impacts across the majority assessed categories in comparison with chemical absorption and membrane gas separation systems. The CO2 capture process via membrane gas absorption has the most significant impact on METP category, with heat consumption as the primary contributing factor accounting for 55%, followed by electricity consumption accounting for 43.1%. According to the sensitivity analysis, heating by natural gas shows a better performance than other heat supply sources in improving overall environmental impacts. In addition, the increasing utilization of renewable energy in electricity supply reduces the global warming potential, fossil resource consumption and ozone formation.

The oil and gas industry in Nigeria, a vital contributor to the nation's economy, has long been associated with significant environmental challenges. Pollution, habitat destruction, and greenhouse gas emissions have raised global concerns about sustainability and corporate responsibility. This empirical study explores the relationship between environmental accounting practices and the financial performance of listed oil and gas companies in Nigeria. We investigated eight oil and gas companies that are publicly traded on the Nigerian Stock Exchange Market (NGX) as of January 17, 2022, from 2011 to 2022. The study employs Driscoll-Kraay standard errors and reveals that environmental accounting had significant effects on returns on assets, earnings per share, and liquidity ratio. The study revealed that the implementation of environmental accounting practices had diverse effects on the performance of oil and gas companies in Nigeria. The findings encourage policymakers and stakeholders in the sector to utilise the insights and design more effective regulations and incentives that promote environmental corporate responsibility. Also, valuable insights into the potential benefits and challenges associated with adopting environmental accounting practices, and influencing the decision-making processes of corporate stakeholders were provided to ensure sustainability in terms of improved financial performance of the oil and gas sector in Nigeria.

Laboratory experiments and investigations into natural phenomena in this research series have unveiled the presence of a gravitational repulsion force that permeates our environment on both microscopic and macroscopic scales, contingent upon the thermal energy present. This paper presents a study exploring novel properties of gravitational forces among gas molecules, employing principles of thermodynamics. A model has been devised based on the interactions between pairs of gas molecules. While traditional models treat gravitational interaction as a singular force, our experimental approach validates it as the composite of two distinct forces: gravitational repulsion and attraction. By utilizing established experimental data on gas thermodynamics, our model demonstrates robust performance both analytically and experimentally. It verifies the coexistence of gravitational repulsion and attraction forces among gas molecules, showcases their Inverse-Cube relationship with distance, and elucidates the direct proportionality of the repulsion force to absolute temperature. This bridges a crucial gap between energy and fundamental forces. The order of magnitudes of gravitational repulsion and attraction forces are found to be considerably large, contrasting with the low values predicted by classical theory, which results from their amalgamation. Recognizing these forces as substantial in magnitude promises unprecedented outcomes and advancements.

Risk management for technological hazards mainly focuses on the consequences on human lives. Although technological risk analysis evaluates environmental vulnerability, it does not reflect the consequences on environmentally exposed elements, such as rivers, water springs, flora, and fauna. This paper's objective was to propose a conceptual framework and create a multidisciplinary evaluation model for environmental risk analysis in the oil and gas industry. Initially, the problem was approached from a global perspective to justify the necessity of a holistic environmental risk analysis methodology in the oil industry, using environmental risk factors as well as underlying factors, such as environmental fragility and lack of resilience. The holistic assessment was carried out based on probabilistic risk analysis methodologies to obtain a holistic environmental risk index, HERI. This methodology was applied to an oil and gas industry company in Colombia. This allowed greater disaggregation of the results to establish priorities for risk reduction actions and identify the company's weaknesses.