The evolving multiphase induction generators (MPIG) with more than three phases are receiving prominence in high power generation systems. This paper aims at the development of a comprehensive model of the wind turbine driven seven-phase induction generator (7PIG) along with necessary the power electronic converters and controller for grid interface. The dynamic model of the system is developed in Maltlab/Simulink. Synchronous reference frame phase-locked loop (SRFPLL) system is incorporated for grid synchronization. The modeling aspects are detailed and the system response is observed for various wind velocities. The effectiveness of seven phase induction generator is demonstrated with the fault tolerant capability and high output power with reduced phase current when compared to conventional 3-phase wind generation scheme. The response of the PLL is analyzed and the results are presented.

Intelligent systems are driven by the latest technological advances in so different areas as sensing, embedded systems, wireless communications or context recognition. This paper focuses on some of those areas. Concretely, the paper deals with wireless communications issues on embedded systems. More precisely, the paper combines the multi-hop networking with Bluetooth technology and a quality of service (QoS) metric, the latency. Bluetooth is a radio license free worldwide communication standard that makes low power multi-hop wireless networking available. It establishes piconets (point-to-point and point-to-multipoint links) and scatternets (multi-hop networks). As a result, many Bluetooth nodes can be interconnected to set up ambient intelligent networks. Then, this paper presents the results of the investigation on multi-hop latency with park and sniff Bluetooth low power modes conducted over the hardware test bench previously implemented. In addition, the empirical models to estimate the latency of multi-hop communications over Bluetooth Asynchronous Connectionless Links (ACL) in park and sniff mode are given. The designers of devices and networks for intelligent systems will benefit from the estimation of the latency in Bluetooth multi-hop communications that the models provide.

We present a first formal analysis of specific and complete local integration. Complete local integration was previously proposed as a criterion for detecting entities or wholes in distributed dynamical systems. Such entities in turn were conceived to form the basis of a theory of emergence of agents within dynamical systems. Here, we give a more thorough account of the underlying formal measures. The main contribution is the disintegration theorem which reveals a special role of completely locally integrated patterns (what we call ι-entities) within the trajectories they occur in. Apart from proving this theorem we introduce the disintegration hierarchy and its refinement-free version as a way to structure the patterns in a trajectory. Furthermore we construct the least upper bound and provide a candidate for the greatest lower bound of specific local integration. Finally, we calculate the i-entities in small example systems as a first sanity check and find that ι-entities largely fulfil simple expectations.

Marine renewable energy is emerging as one of the fast-growing industry in the last decades, as modern society pushes for technologies that can convert energy contained from winds, waves, tides and stream flows. The implementation of renewable energy technologies impose high demands on both structural and environmental engineering, as the energy converters have to work under extreme conditions where parameters such as sea-bottom configuration, water transparency and depth, sea-states and prevailing winds are harsh. Constant monitoring of the marine environment is crucial in order to keep this sector reliable. Active acoustics is becoming a standard tool to collect multi-dimensional data from physical, geological and biological properties of the marine environment. The Div. of Electricity of Uppsala University have been developing an environmental monitoring platform based on sonar systems. This platform aims to monitor the installation, operation and decommissioning of marine renewable energy converters. The focus will be given the observations of behaviors of marine animals in vicinity of energy converters but also structural inspection and monitoring of MRETs. This paper describes how this multifunctional environmental monitoring platform come to existence from the design to the deployment phase.

The ground consists of many layers of soil with different properties. The propagation speed and path of seismic waves are affected by different soil layers. It is necessary to understand that layered soil exhibits different dynamic behaviors and responses under the action of seismic waves. This study utilized weathered soil and silica sand as materials to create multi-layered soil conditions with varying degrees of compaction. By conducting 1 g shaking table test on multi-layered soil, the interaction and influence between different soil layers under different earthquake conditions were observed. The approach of numerical analysis aims to validate the experimental results and provide an in-depth understanding of the dynamic behaviors of multi-layered soil grounds during seismic events. The results of this study show that the amplification effect of seismic waves is related to the number of soil layers and the degree of compaction of the soil layers. This indicates that the multi-layered soil ground and the behavior of the soil layers play an important role in the propagation and impact of seismic waves, and this amplification effect is of great significance in actual seismic disaster risk assessment and design.

Organ-on-a-chip (OOC) is an emerging technology that simulates an artificial organ within a microfluidic cell culture chip. Current cell biology research focuses on in vitro cell culture due to various limitations of in vivo testing. Unfortunately, in vitro cell culture fails to provide an accurate microenvironment, and in vivo cell culture is expensive and has historically been a source of ethical controversy. OOC aims to overcome these shortcomings and provide the best of both in vivo and in vitro cell culture research. The key component of the OOC design is utilizing microfluidics to ensure a stable concentration gradient, dynamic mechanical stress modeling, and accurate reconstruction of a cellular microenvironment. OOC also has the advantage of complete observation and control of the system, which is impossible to recreate in in vivo research. Multiple throughputs, channels, membranes, and chambers are constructed in a polydimethylsiloxane (PDMS) array to simulate various organs on a chip. Various experiments can be performed utilizing OOC technology, including drug delivery research and toxicology. Current technological expansions involve multiple organ microenvironments on a single chip, allowing for studying inter-tissue interactions. Other developments in the OOC technology include finding a more suitable material as a replacement for PDMS and minimizing artefactual error and non-translatable differences.

Light can interfere like a wave in a multi-path experiment, but it also has particle properties when interacting with matter. In a closer look, the interference pattern is created by many individual detections ("clicks"), which do not all occur simultaneously. An established assumption is therefore that a single light particle is capable of interfering with itself by superimposing all possibilities to get from the source to the detector. This is in stark contrast to our experience with macroscopic objects, which always "decide" in favour of only one of the alternative paths.In 2010, Jin et al. (Ref. 15) described an event-based model which allowed the authors to show that an interference pattern consisting of clicks can arise in a multi-path experiment even if photons, like macroscopic objects, only follow one path. To do this, photons must be able to transmit the information about their travelling duration to the detector and the detector must have a basic memory. A threshold function uses the message of several light quanta to decide whether a single detection is initiated, which is not the evidence for a single photon. In this "proof of principle", the authors do not claim that the detector function is a realistic one.In the present paper, this detector is replaced by a material consisting of ionizable molecules whose interaction with light takes place according to a modified version of Einstein's radiation laws. Based on this, a photon pair interaction mediated by matter takes place, which in a multi-path experiment generates an interference pattern of clicks at the detector, even if an arbitrary amount of time elapses between the individual detections. In the present model an interference pattern with minima that have less than half the intensity of the maxima is the result of a peculiar behaviour of the detector: In this case, the entirety of its electrons must be described as a unit (a “field”) with many equidistant energy levels. The results of a simulation are presented which enable the model to be tested in experiments.

Light can interfere like a wave in a multi-path experiment, but it also has particle properties when interacting with matter. In a closer look, the interference pattern is created by many individual detections ("clicks"), which do not all occur simultaneously. An established assumption is therefore that a single light particle is capable of interfering with itself by superimposing all possibilities to get from the source to the detector. This is in stark contrast to our experience with macroscopic objects, which always "decide" in favour of only one of the alternative paths.In 2010, Jin et al. (Ref. 15) described an event-based model which allowed the authors to show that an interference pattern consisting of clicks can arise in a multi-path experiment even if photons, like macroscopic objects, only follow one path. To do this, photons must be able to transmit the information about their travelling duration to the detector and the detector must have a basic memory. A threshold function uses the message of several light quanta to decide whether a single detection is initiated, which is not the evidence for a single photon. In this "proof of principle", the authors do not claim that the detector function is a realistic one.In the present paper, this detector is replaced by a material consisting of ionizable molecules whose interaction with light takes place according to a modified version of Einstein's radiation laws. Based on this, a photon pair interaction mediated by matter takes place, which in a multi-path experiment generates an interference pattern of clicks at the detector, even if an arbitrary amount of time elapses between the individual detections. In the present model an interference pattern with minima that have less than half the intensity of the maxima is the result of a peculiar behaviour of the detector: In this case, the entirety of its electrons must be described as a unit (a “field”) with many equidistant energy levels. The results of a simulation are presented which enable the model to be tested in experiments.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

In order to improve real-time performance of gesture recognition by micro-Doppler map of mmWave Radar, the point cloud based gesture recognition for mmWave Radar is proposed in this paper.Two steps are carried out for mmWave Radar based gesture recognition. The first step is to estimate the point cloud of the gestures by 3D-FFT and the peak grouping. The second step is to train the TRANS-CNN model by combining the multi-head self-attention and the 1D-convolutional network, so as to extract the features in the point cloud data at a deeper level to categorize the gestures. In the experiments, TI mmWave Radar sensor IWR1642 is used as benchmark to evaluate the feasibility of the proposed approach. The results show that the accuracy of the gesture recognition reaches 98.5%. In order to prove the effectiveness of our approach, a simply 2Tx2Rx Radar sensor is developed in our lab and the accuracy of recognition reaches 97.1%. The results show that our proposed gesture recognition approach achieves the best performance in real-time with limited training data, in comparison with the existing methods.

The South Asian economy is on the rise but struggling with power shortages and heavy dependence on fossil fuels. For sustained growth, there is a need for access to readily available energy sources, such as electricity. Trading clean electrical energy among neighbouring countries can ensure access to readily available points. South Asia has a diverse range of energy sources, including hydropower, that are available in the region. However, sectorial barriers can impede energy trading. This study has attempted to assess the readiness and barriers to Nepal’s cross-border energy trade with India and Bangladesh using the Analytic Hierarchy Process (AHP). This study also recommends possible measures to strengthen preparedness and address the challenges in energy trade that can be tailored and applied to other cross-country situations.

In recent years, the viability of employing multi-agent reinforcement learning technology for adaptive traffic signal control has been extensively validated. However, owing to restricted communication among agents and the partial observability of the traffic environment, the process of mapping road network states to actions encounters numerous challenges. To address this problem, this paper proposes a multi-agent deep reinforcement learning model with an emphasis on communication content (CMARL). The model decouples the complex relationships between multi-signal agents through centralized training and decentralized execution. Specifically, we first pass the traffic state through an improved deep neural network to achieve the extraction of high-dimensional semantic information and the learning of the communication matrix. Then the agents selectively interact with each other based on the learned communication matrix and generate the final state features. Finally, the features are inputted to the QMIX network to achieve the final action selection. We compare the CMARL model with 6 other baseline algorithms in real traffic networks. The results show that CMARL can significantly reduce vehicle congestion, and run stably in various scenarios.

Stochastic modelling of geometrically imperfect steel frame structures requires inputs of statistical values of the imperfection parameters, in some cases also with suitably selected mutual correlations between these input parameters. The paper presents a verification study of two stochastic methods to directly model the initial global geometrical imperfections of the steel frame structures. The stochastic input values of geometrical imperfections are derived from the tolerance criteria of the corresponding European Standard. Two advanced stochastic methods have been developed, referred as #RSS (random story sway) and #RSP (random story position). These methods are verified using random sampling simulations. This study provides useful provisions for the advanced numerical analyses of multi-story steel frames of various geometries. The proposed methods are verified for equidistant story heights and for structures of up to 24 stories, hence might be used for the most types of the standard steel frame structures.

We propose a new hierarchy of the vector derivative nonlinear Schr{\"o}dinger equations and consider the simplest multiphase solutions of this hierarchy. The study of the simplest solutions of these equations led to the following results. First, the three-leaf spectral curves $\Gamma=\{(\mu,\lambda)\}$ of the simplest multiphase solutions have a quite simple symmetry. They are invariant with respect to holomorphic involution $\tau$. The type of this involution depends on the genus of the spectral curve. Or the involution has the form $\tau:(\mu,\lambda)\to(\mu,-\lambda)$, or $\tau:(\mu,\lambda)\to(-\mu,-\lambda)$. The presence of symmetry leads to the fact that the dynamics of the solution is determined not by the entire spectral curve $\Gamma$, but by its factor $\Gamma/\tau$, which has a smaller genus. Secondly, it turned out that the dynamics of the two-component vector $\bp=(p_1,p_2)^t$ is determined, first of all, by the dynamics of its length $\abs{\bp}$. Independent equations determine the dependence of the direction of the vector $\bp$ from its length. In cases where the direction of the vector $\bp$ is fixed, the corresponding spectral curve splits into separate components. In conclusion, we note that, as in the case of the Manakov system, the equation of the spectral curve is invariant with respect to the orthogonal transformation of the vector solutions. I.e., the solution can be found from the spectral curve up to the orthogonal transformation. This fact indicates that the spectral curve does not depend on the individual components of the solution, but on their symmetric functions. Thus, the spectral data of multiphase solutions have two symmetries. These symmetries make it difficult to reconstruct signals from their spectral data. The work contains examples illustrating these statements.

This paper investigated reliability modeling for systems subject to dependent competing risks considering that the variation of failure threshold is not considered in most studies on competing failure reliability. Firstly, the variation of degradation quantity under shocks was analyzed, and the variation of threshold was considered on this basis. Secondly, the cumulative degradation under the influence of the random shock process was analyzed. The attractive property of copula is symmetry. Then, A linear Wiener process model is applied to model performance degradation failure, and a multi-performance-degradation correlated-competition model based on a Copula function is constructed, which considers the correlated competition between multiperformance degradation failures. Lastly, the micromotor system is used to analyze the applicability of the proposed model for bivariate instances. demonstrating the rationality and effectiveness of the proposed model.

Is it possible that the addition of wild-growing flowers with anti-inflammatory applications can improve the antioxidant properties of rapeseed and multifloral honey? The study objective was a comparative analysis of two honey varieties enriched by flowers of six plant species, based on the content of the antioxidant capacity as well as total flavonoids and phenolic content. Experiments demonstrated that at each level of enrichment there was an improvement in antioxidant properties compared to honey of both varieties without additives, especially in the case of dried flowers. Primula veris L. and Pulmonaria officinalis L. improved the antioxidant properties and phenolic content most effectively in honey at all levels of enrichment. Rapeseed-type honey produces a better matrix for the incorporation of natural plant metabolites into honey. The content of biologically active substances in honey enriched with flowers gives hope for new applications of health-promoting substances contained in wild plants.

Land-use planning plays an important role in agricultural development, however it lacks tools to support planner in proposing land-use planning solutions especially, under saltwater intrusion condition in the coastal regions. This study aims to apply optimization in analyzing land-use solutions for agricultural land-use planning. In which a multi-objective optimization model is developed to optimize land-use area including land-use allocation taking into account socio-economic and environmental factors. The model has been applied in three districts of Soc Trang province, Vietnam (Long Phu, My Xuyen and Tran De) representing three ecological regions including salt water, brackish water and freshwater in the Mekong Delta of Vietnam. The results showed that two multi-objective optimization scenarios (in terms of profit, labor, environment benefits and risk reduction) have been implemented: (i) Multi-objective optimization of agricultural land-use until 2030 under normal conditions; (ii) Optimizing agricultural land-use until 2030 under climate change conditions similar to the 2016 drought and saltwater intrusion phenomenon in the Mekong Delta. The results showed that the second scenario is the option considered for implementing land-use plan thanks to the balance between good profits and minimizing economic and environmental risk. The land allocation was carried out taking into account household economic, the influence of adjacent production types, local traffic and canal systems factors to allocate optimal land-use areas. The combination of land-use optimization and spatial allocation process can help planners improve the quality of agricultural land-use planning.

Under high-frequency operating conditions, the high-speed solenoid valve (HSV) experiences energy loss and heat generation, which significantly impact its operational lifetime. Reducing the energy loss of HSV without compromising its opening response characteristics poses a significant challenge. To address this issue, a finite element simulation model of HSV coupled with a current feedback model is constructed to investigate the synergistic effects of dynamic response and energy loss. Predictive models for the opening response time, HSV driving energy, and Joule energy using Back Propagation neural network (BPNN) are established. Furthermore, a multi-objective optimization study on the current driving strategy using Non-dominated Sorting Genetic Algorithm II (NSGA-II) is conducted. After optimization, although there was a 6.24% increase in the opening response time, both HSV drive energy and Joule energy were significantly reduced by 15.67% and 22.49%, respectively. The proposed multi-objective optimization method for HSV driving strategy holds great significance in improving its working durability.

Landward displacement of coastal boulders is a morphodynamic signature of inundation and erosion processes. The study of these movements can provide useful elements for coastal hazards assessment. In this note, using open-access remote sensing resources, the 2017 to 2021 annual mobility of medium, coarse, and very coarse boulders spread over about 100 km of the eastern coast of the Gulf of Taranto (Italy) is detected. A large interannual variability was found. As established by multi-temporal object-based image analysis, one hundred and ten boulders changed position between July 2019 and June 2020, no boulder was displaced between July 2017 and July 2018, and few boulders were displaced between July 2018 and July 2019, and June 2020 and September 2021. A hydrodynamic analysis of the investigated boulder displacement led to the estimation of the energy of nearshore waves that hit the coast. The storm Detlef, that crossed over the Mediterranean Sea during 11-13 November 2019, is presumed to be the main cause of the massive displacement phenomenon.

Fabry-Pérto (FP) cavity is the essential component of ultra-stable laser (USL) for gravitational wave detection, which couples multi-physic (Optical/Thermal/Mechanics) fields and requires ultra-high precision. To satisfy the requirements of precise and efficient design, a multi-physic coupling optimization method for fixing cubic FP cavity based on data learning is proposed. A multi-physic model for the cubic FP cavity is established and the performance is obtained by finite element analysis. The key performance indices (V, wF, wF) and key design variables (d, l, F) are determined considering the features of the FP cavity. The 49 sets of data by orthogonal experiment are acquired for the establishment and comparison of different data learning models (NN, RSF, KRG). The result turns out that the neural network has the best performance. Based on NSGA-II, the Pareto optimal front is obtained and the optimal combination of design variables is finally determined as {5,32,250}. The performance after optimization has proven to be a great improvement, of which the displacement under the fixing force and vibration test are decreased by more than 60%. The optimization strategy can not only help the design of the FP cavity but also enlighten other optimization fields.

The feasibility of recovering bioactive antioxidants from Phyllantus emblica leaves using ethanol -water mixture (0 – 100%) and heat-assisted extraction technology (HAE-T) was investigated in this present study. To this effect, the process parameter of operating temperature (OT: 30 -50 oC), solid -to-liquid ratio (S:L: 1:20 - 1:60 g/mL) and extraction time (ET: 45 - 180 min) were investigated on the extract total phenolic content (TPC, mg GAE/g d.w), yield (EY, %) and antioxidant activity (μM AAE/g d.w) by employing the Box-Behnken experimental design (BBD) available in response surface methodology (RSM). Multi-objective process optimization using the desirability function algorithm to determine set of process variables that simultaneously optimize process responses of TPC, EY and AA was also investigated. The recovery process was thereafter modeled with BBD-RSM and multi gene genetic programming (MGGP) algorithm and model reliability assessment via Monte Carlo simulation were conducted for the best performing set of models for predicting TPC, EY and AA values. The HPLC characterization of the recovered extract was carried out to ascertain the phenolic compound constituents of the Phyllantus emblica leaf extract. The 50% ethanol solution was found to be the best for the optimal extraction of antioxidants from Phyllantus emblica leaves. The HAE-T was suitable for recovering bioactive extract from Phyllantus emblica leaves and investigated process parameters have impacts on the recovery process. The process parameters that simultaneously gave the optimum EY of 21.6565%, TPC of 67.116 mg GAE/g and AA of 3.68583 µM AAE/g were OT of 41.61 oC, S:L of 1:60 g/mL and ET of 180 min. The HPLC extract profiling revealed that the bioactive constituents present in the recovered extract were betulinic acid, gallic acid, chlorogenic acid, caffeic acid, ellagic acid, and ferulic acid. Both the developed BBD-RSM and evolved MGGP-based models predicted the observed process response of TPC, EY and AA satisfactorily with BBD-RSM models marginally better in their predictions. The reliability results showed that the BBD-RSM models predicted TPC, EY and AA values with high certainty of 99.985%, 97.569% and 98.661%, respectively.

Fine-tuning is an important technique in transfer learning that has achieved significant success in tasks that lack training data. However, as it is difficult to extract effective features for single-source domain fine-tuning when the data distribution difference between the source and the target domain is large, we propose a transfer learning framework based on multi-source domain called adaptive multi-source domain collaborative fine-tuning to address this issue. This approach utilizes multiple source domain models for collaborative fine-tuning, thereby improving the model's feature extraction capability in the target task. Specifically, this approach employs an adaptive multi-source domain layer selection strategy to customize appropriate layer fine-tuning schemes for the target task among multiple source domain models. The objective is to extract more efficient features. Furthermore, a novel multi-source domain collaborative loss function is designed to facilitate the precise extraction of target data features by each source domain model. Simultaneously, it works towards minimizing the output difference among various source domain models, thereby enhancing the adaptability of the source domain model to the target data. In order to validate the effectiveness of the proposed the adaptive multi-source domain collaborative fine-tuning framework, it is analyzed and compared with the most widely used fine-tuning methods by applying them to seven publicly available visual categorization datasets commonly employed in transfer learning. Experimental results demonstrate that, in comparison with the existing fine-tuning approaches, our method not only enhances the accuracy of feature extraction in the model but also provides precise layer fine-tuning schemes for the target task, resulting in state-of-the-art performance.

The narrow parking space will result in difficulties in path planning and spot turning caused by sudden changes and discontinuities in path curvature. To address the problem, this paper investigates the performance of three path planning algorithms and proposes a path optimization algorithm. First, the narrow parking space is defined based on single-step parking of the arc-line combination parking algorithm. Second, to compare the arc-line combination algorithm, Hybrid A* algorithm, and particle swarm optimization parking algorithm under different narrow parking spaces, a multi-objective evaluation function is proposed, including three evaluation indicators, namely, the path length, the number of positive and negative conversions of vehicle speed, and the smoothness of the path. Their performance is compared by simulation conducted in MATLAB, the results show that the Hybrid A* algorithm is the better than others for narrow parking spaces. Third, to smooth the planning path, a path optimization algorithm based on the cubic B-spline curve and gradient descent is proposed. Finally, the simulation is conducted between the proposed algorithm and Hybrid A* algorithm, the result shows that the proposal can effectively eliminate the curvature mutation point and constrain the path curvature to meet the requirements of a smooth path.

This work aims to describe the dielectric behaviours of four main tissues in the human forearm using mathematical modelling, including fat, muscle, blood, and bone. Determining the electrical response of multiple tissues can help develop physiological monitoring of an organ or a body’s section by filtering out the impedance contributions from the surrounding tissues to blood flow-induced impedance variations. Multi-frequency bioimpedance analysis (MF-BIA) was initially performed using the finite element method (FEM) with a 3D forearm model followed by a pilot study to characterise the response of actual forearm tissues from 1 kHz to 349 kHz. Both the simulation and experimental results were fitted to a single-dispersion Cole model (SDCM) and a multi-dispersion Cole model (MDCM) to determine the Cole parameters for each tissue. The correlation analysis and Bland-Altman plot indicated a good fit between raw and fitted impedance values using both SDCM and MDCM. Overall, MDCM exhibited better performance in fitting and estimation of the Cole parameters with correlation coefficient (R2) of 0.99 and 0.97, root mean squared error (RMSE) of 0.09 Ω and 0.14 Ω, and mean difference (mean±standard deviation) of 0.00±0.09 Ω and -0.03±0.14 Ω for the real part and imaginary part of impedance, respectively.

Abstract: The diffusion of competition under the coexistence of multi-generation products has become one of the important challenges faced by enterprises in their daily and sustainable operations. At the same time, the competition between different brands has intensified the difficulty and complexity of decision-making in the process of multi-generation product operation, Therefore, based on the Norton-Bass model diffusion process, this paper introduces two marketing variables, dynamic price and quality level, builds a multi-generation product diffusion model under the dual-brand competition, and analyzes the impact of the company's revenue on the launch time to market, pricing, quality or technical level. By using system dynamics (SD) method, From the perspective of strong brand and weak brand enterprises, the competition diffusion model is built and simulated. The simulation shows that: i) When enterprises have the same brand competitiveness, reducing the pricing level cannot obtain more revenue, but diminish the overall revenue of the industry; Raising the pricing level can get more revenue, but also improve the revenue of competitors. ii) When the competitive strength of enterprises is different, the strong brand tends to maintain a stable pricing on the basis of improving the quality level, or slightly raise the price. Weak brands tend to raise the pricing of new products significantly on the basis of improving the quality level. iii) The launch time to market decision of new product is influenced by the degree of product quality upgrade. Therefore, the frequency of releasing new products should trade-off against the degree of technological upgrading of product quality. This paper provides the theoretical basis and new insights for the new product launch and operation decision of enterprises.

In recent years, intelligent identification and prediction of ore deposits based on deep learning algorithm and image processing technology has gradually become one of the research frontiers in the field of geological and metallogenic prediction. However, this method also has many problems that need to be solved. For example, (1) very few trainable image samples containing mineral point labels; (2) The geological image features are small and irregular, and the image similarity is high; (3) It is difficult to calculate the influence of different geological prospecting factors on ore mineralization. Based on this, this paper constructs a deep learning network model Multiscale Feature Attention Framework (MFAF) based on geo-image data. The results show that MFCA-Net module in MFAF model can solve the problem of scarce mine label images to a certain extent. In addition, the channel attention mechanism SE-Net module can quantify the difference of influence of different source factors on mineralization. The prediction map is obtained by applying the MFAF model in the study of deposit identification and prediction in the research area of the southern section of Qin-hang metallogenic Belt. In the forecast map, many regions have high metallogenic potential. Through observation, it is found that the above predicted area covers 100% of the known ore deposits at present, which has a good prediction effect. Later, we can find out the specific reasons through field verification. The multi-scale feature fusion and attention mechanism MFA Framework in this paper can provide a new way of thinking for geologists in mineral exploration. The research of this paper also provides resource guarantee and technical support for the sustainable exploitation of mineral resources and the sustainable growth of society and economy.

This work aims to produce a cartographic model that identifies areas with a greater probability of finding karstic caves - the endokarst potential - in the northern sector of Santo António Plateau (Estremadura Limestone Massif, Central Portugal). Geological, topographic, hydrogeological, and vegetation cover data were collected, processed, and integrated into a spatial database using a geographic information system (GIS). The location of known cave entrances in the study area was also identified from the records of local public institutions and speleological teams. Four conditioning factors were extracted from the collected data, including lithostratigraphic units, fracture density, relief energy, and land cover. In a multi-criteria decision-making analysis framework, each previously chosen conditioning factor and respective classes/categories were weighted using the analytic hierarchy process (AHP). With an agreement of 81.9%, the results of the cartographic model constructed in GIS seem to be promising, considering that the entrances of the known caves are mainly located in areas classified as having high to very high endokarst potential. This prototype of the endokarst potential map for the study area can be used in strategic and operational environmental planning (at least on a local scale), as it can assist decision-makers, competent authorities, and local speleological teams in a more accurate and thoughtful definition of the areas that should be investigated, providing a substantial reduction in times and costs field prospecting.

This study discusses the experimental assessment of the in-plane mechanical behavior of a multi-leaf stone masonry wall built from cut stone and reinforced with metal connectors (cramps and dowels). The wall, inspired by conventional multi-leaf stone walls, is meant for use in modern stone masonry buildings. The wall is constructed from two parallel load-bearing walls with a cavity between them, which aims to conceal the installation and insulation needed in modern buildings. The load-bearing walls are connected with cramps and dowels at certain intervals so that the wall works as a single section against horizontal and vertical loads. To characterize the in-plane behavior of the proposed wall, compressive, triplet, and diagonal compression tests were conducted to investigate the compressive strength, shear strength, modulus of elasticity, stiffness, ductility, and energy absorption of the wall. Compared with dry and mortar joint walls, the use of dowels increased the initial shear capacity of the wall by 11 and 19 times, respectively. The application of cramps without curving channels inside the individual stone elements decreased the compressive strength by 18%. The energy absorption of the designed walls with metal connectors was substantially increased to that of the specimens representing conventional stone walls. The results obtained show the applicability of the wall due to its higher shear strength and minimal drop in compressive strength, which is within acceptable limits.

Mental health could worsen in children and adolescents with autism spectrum disorder during the Covid19 pandemic. In addition, their parents could be more at risk for an increase in anxiety and depression symptomatology. This study aims to understand the adaptation and the psychosocial well-being in a sample of 16 males aged 10-21 years old with Asperger syndrome after the quarantine for Covid19 when they return to school and partially to their activities in September 2020, The approach adopted is multi-informant with a battery of questionnaires on psychological health and adaptation given by a secure online web data Qualtrics both to adolescents and also to their parents. Paralleling matched peers with typically development were assessed adopting the same methodology. The results evidenced several difficulties in Asperger’s psychological health, especially in anxiety and socialization. Also adaptation is put in crisis, even if they reported a good comprehension and adoption of the behaviors anti-Covid19. Parents of children with Asperger reported similar psychological difficulties and general health than those of the group of children typically developing. Some clinical indications could be discussed for psychologists who follow children and adolescents with Asperger.

Object recognition is an essential element of machine intelligence tasks. However, one model cannot practically be trained to identify all the possible objects it encounters. An ensemble of models may be needed to cater to a broader range of objects. Building a mathematical understanding of the relationship between various objects that share comparable outlined features is envisaged as an effective method of improving the model ensemble through a pre-processing stage, where these objects' features are grouped under a broader classification umbrella. This paper proposes a mechanism to train an ensemble of recognition models coupled with a model selection scheme to scale-up object recognition in a multi-model system. An algorithmic relationship between the learnt parameters of a trained classification model and the features of input images is presented in the paper for the system to learn the model selection scheme. The multiple models are built with a CNN structure, whereas the image features are extracted using a CNN/VGG16 architecture. Based on the models' excitation weights, a neural network model selection algorithm, which links a new object with the models and decides how close the features of the object are to the trained models for selecting a particular model for object recognition is developed and tested on a five-model neural network platform. The experiment results show the proposed model selection scheme is highly effective and accurate in selecting an appropriate model for a network of multiple models.

Wheat and barley are among the primary food resources of the world population; therefore, their growth and observation are essential in farms to enhance food security worldwide. On top of that, careful observation of the product is essential to find solutions for the issues faced during their production and to reduce the impacts of weather changes. With the advancement of Remote Sensing technology, the observation and estimation process has increased. In this study, numbers of spectral vegetation indices was used along with canopy biophysical properties ( LAI ) and biochemical properties (chlorophyll), there calculated from (Landsat 8 and Sentinel-2) satellite data. The wheat and barley samples were collected before were be ready for harvest, and a relation with the vegetarian indices was established using the Multi-Linear Regression module, in which the equations used in predicting the harvest were developed and used to create a graph for expected harvest. The result indicated that there is a strong relationship between the vegetation indices of Sentinel-2 and Landsat images and the actual grain yield with R² of 0.77 and 0.71, respectively. The results show that the strongest correlation is observed between the LAI data obtained from Sentinel data and cereal yield data, with an R² 0.68, and the highest correlation for the indices of Landsat images is observed in the NDWI with R² 0.59 and the lowest degree of error was in the root mean square error (RMSE) for the Sentinel-2 and Landsat 8 with 0.57 and 1.54. In addition, this study also showed that the least relationship for grain yield prediction was observed between the NDRI for Sentinel-2 (R² 0.1) and SAVI for Landsat image (R² 0.47).

Deep convolutional neural networks (CNNs) have been widely used in various medical imaging tasks. However, due to the intrinsic locality of convolution operation, CNNs generally cannot model long-range dependencies well, which are important for accurately identifying breast cancer from unregistered multi-view mammograms. This motivates us to leverage the architecture of Vision Transformers to capture long-range relationships of multiple mammograms from the same patient. For this purpose, we employ local Transformer blocks to separately learn patch relationships within a specific view (CC/MLO) of one side (right/left) of mammogram. The outputs from different views and sides are concatenated and fed into global Transformer blocks, to jointly learn patch relationships between two different views of the left and right breasts. To evaluate the proposed model, we retrospectively assembled a dataset involving 949 sets of CC and MLO view mammograms, which include 470 malignant cases and 479 normal or benign cases. We trained and evaluated the model using a five-fold cross-validation method. Without any arduous preprocessing steps (e.g., optimal window cropping, chest wall or pectoral muscle removal, two-view image registration, etc.), our two-view Transformer-based model achieves lesion classification accuracy of 77.0% and area under ROC curve (AUC = 0.814), outperforming state-of-the-art multi-view CNNs by 3.1% and 3%, respectively. Meanwhile, the new two-view model improves mammographic case classification accuracies of two single-view models by 7.4% (CC) and 4.5% (MLO), respectively. The promising results unveil the great potential of using Transformers to develop high-performing computer-aided diagnosis (CADx) schemes of mammography.

In this paper, we propose, implement, and test two novel downlink LTE scheduling algorithms. The implementation and testing of these algorithms were in Matlab, and they are based on the use of Reinforcement Learning, more specifically, the Qlearning technique for scheduling two types of users. The first algorithm is called a Collaborative scheduling algorithm, and the second algorithm is called a Competitive scheduling algorithm. The first type of the scheduled users is the Primary Users, and they are the licensed subscribers that pay for their service. The second type of the scheduled users is the Secondary Users, and they could be unlicensed subscribers that dont pay for their service, device to device communications, or sensors. Each user whether it is a primary or secondary is considered as an agent. In the Collaborative scheduling algorithm, the primary user agents will collaborate in order to make a joint scheduling decision about allocating the resource blocks to each one of them, then the secondary user agents will compete among themselves to use the remaining resource blocks. In the Competitive scheduling algorithm, the primary user agents will compete among themselves over the available resources, then the secondary user agents will compete among themselves over the remaining resources. Experimental results show that both scheduling algorithms converged to almost ninety percent utilization of the spectrum, and provided fair shares of the spectrum among users.

Finite element (FE) modeling is commonly used as a method to investigate the influence of medical devices, such as implants and screws and their effects on the biomechanical behavior of the spine. Another simulation method is a multi-body simulation (MBS), where the model is composed of several non-deformable bodies. MBS solvers generally require a very short computing time for dynamic tasks compared to an FE analysis. Considering this computational advantage, in this study, we examine whether parameters whose values are not known a priory can be determined with sufficient accuracy using MBS model. Therefore, we propose a Many-at-a-time sensitivity analysis method that allows approximating these a priory unknown parameters without requiring long simulation times. This method enables a high degree of MBS model optimization to be achieved in an iterative process. The sensitivity analysis method is applied to a simplified screw-vertebra model, consisting of an anterior anchor implant screw and vertebral body of C4. An experiment described in the literature is used as a basis for developing and assessing the potential of the method for sensitivity analysis and to validate the models action. The optimal model parameters for the MBS model were determined to be c=823224N/m for stiffness and d=488Ns/m for damping. The presented method of parameter identification can be used in studies including more complex MBS spine models or to set initial parameter values that are not available as initial values for FE models.

We provide methodology and numerical results for the Hattendorff differential equa- tion for the continuous time evolution of the variance of L(j)t , the loss at time t random variable for a multi-state process, given that the state at time t is j.

Cervical fusion has been a standard procedure for treating the abnormalities associated with the cervical spine. However, the reliability of anterior cervical discectomy and fusion (ACDF) has become arguable due to its adverse effects on the biomechanics of adjacent segments. One of the drawbacks associated with ACDF is adjacent segment degeneration (ASD) which has served as the base for the development of dynamic stabilization systems (DSS) and total disc replacement (TDR) devices for cervical spine. However, the hybrid surgical technique has also gained popularity recently but their effect on the biomechanics of cervical spine is not well researched. Thus, the objective of this FE study was to draw the comparison among single, bi-level and hybrid surgery with DCI implant with traditional fusion. Reduction in range of motion (ROM) for all the implanted models was observed for all the motions except extension, compared to intact model. The maximum increase in ROM of 42% was observed at C5-C6 level in Hybrid-DCI model. The maximum increase in adjacent segment’s ROM of 8.7% was observed in multilevel fusion model. The maximum von Mises stress in the implant was highest for the multilevel DCI model. Our study also showed that the shape of DCI implant permits flexion/extension relatively more compared to lateral bending and axial rotation.

The testing requirements of the active phased array antennas are very different from those of traditional passive antennas, due to its beam steering capability. Usually, each beam profile of the active phased array needs a separate radiation pattern test, which makes the overall testing time extremely long. Thus the traditional antenna test method can no longer meet the efficiency and cost requirements of new active phased array antennas test. In this paper, a fast test method tailored for phased array antennas is proposed that offers significantly reduced testing time at the expense of slight sacrifice of the accuracy. Using the simulated element pattern in array and ideal port excitation, the beam profile in any direction can be predicted by testing only a certain beam profile. Through theoretical derivation and experiments, the effectiveness of the method is verified, and the testing efficiency of the phased array antenna is demonstrated to be improved by ten times or even more.

Use of a multi-sensor approach can provide citizens a holistic insight in the air quality in their immediate surroundings and assessment of personal exposure to urban stressors. Our work, as part of the ICARUS H2020 project, which included over 600 participants from 7 European cities, discusses data fusion and harmonization on a diverse set of multi-sensor data streams to provide a comprehensive and understandable report for participants, and offers possible solutions and improvements. Harmonizing the data streams identified issues with the used devices and protocols, such as non-uniform timestamps, data gaps, difficult data retrieval from commercial devices, and coarse activity data logging. Our process of data fusion and harmonization allowed us to automate the process of generating visualizations and reports and consequently provide each participant with a detailed individualized report. Results showed that a key solution was to streamline the code and speed up the process, which necessitated certain compromises in visualizing the data. A thought-out process of data fusion and harmonization on a diverse set of multi-sensor data streams considerably improved the quality and quantity of data that a research participant receives. Though automatization accelerated the production of the reports considerably, manual structured double checks are strongly recommended.

In clinical diagnostics and longitudinal studies, the reproducibility of MRI assessments is of high importance in order to detect pathological changes, but developments in MRI hard- and software often outrun extended periods of data acquisition and analysis. This could potentially introduce artefactual changes or mask pathological alterations. However, if and how changes of MRI hardware, scanning protocols or preprocessing software affect complex neuroimaging outcomes from e.g. diffusion weighted imaging (DWI) remains largely understudied. We therefore compared DWI outcomes and artefact severity of 121 healthy participants (age range 19-54 years) who underwent two matched DWI protocols (Siemens product and Center for Magnetic Resonance Research sequence) at two sites (Siemens 3T Magnetom Verio and Skyra^fit). After different preprocessing steps, fractional anisotropy (FA) and mean diffusivity (MD) maps,obtained by tensor fitting, were processed with tract-based spatial statistics (TBSS). Inter-scanner and inter-sequence variability of skeletonised FA values reached up to 5% and differed largely in magnitude and direction across the brain. Skeletonised MD values differed up to 14% between scanners. We here demonstrate that DTI outcome measures strongly depend on imaging site and software, and that these biases vary between brain regions. These regionally inhomogeneous biases may exceed and considerably confound physiological effects such as ageing, highlighting the need to harmonise data acquisition and analysis. Future studies thus need to implement novel strategies to augment neuroimaging data reliability and replicability.

Incident solar radiation (insolation) passing through the forest canopy to the ground surface is either absorbed or scattered. This phenomenon, known as radiation attenuation, is measured using the extinction coefficient (K). The amount of radiation at the ground surface of a given site is effectively controlled by the canopy’s surface and structure, determining its suitability for plant species.Menhinick’s and Simpson biodiversity indexes were selected as spatially explicit response variables for the regression equation using canopy structure metrics as predictors. Independent variables include modeled area solar radiation, LiDAR derived canopy height, effective leaf area index data derived from multi-spectral imagery, and canopy strata metrics derived from LiDAR point-cloud data. The results support the hypothesis that, 1.) canopy surface and strata variability may be associated with understory species diversity due to habitat partitioning and radiation attenuation, and that, 2.) such a model can predict both this relationship and biodiversity clustering.The study data yielded significant correlations between predictor and response variables and was used to produce a multiple-linear model comprising canopy relief, texture of heights, and vegetation density to predict understory plant diversity. When analyzed for spatial autocorrelation, the predicted biodiversity data exhibited non-random spatial continuity.

Aim: To determine whether an AI model and single sensor measuring acceleration and ECG could model cognitive and physical fatigue for a self-paced trail run. Methods: A field-based protocol of continuous fatigue repeated hourly induced physical (~45 minutes) and cognitive (~10 minutes) fatigue on one healthy participant. Physical load was a 3.8 km, 200 m vertical gain, trail run with acceleration and electrocardiogram (ECG) data collected using a single sensor. Cognitive load was a Multi Attribute Test Battery (MATB) and separate assessment battery including the Finger Tap Test (FTT), Stroop, Trail Making A and B, Spatial Memory, Paced Visual Serial Addition Test (PVSAT), and a vertical jump. A fatigue prediction model was implemented using a Convolutional Neural Network (CNN). Results: When the fatigue test battery results were compared for sensitivity to the protocol load, FTT right hand (R2 0.71) and Jump Height (R2 0.78) were the most sensitive while the other tests were less sensitive (R2 values Stroop 0.49, Trail Making A 0.29, Trail Making B 0.05, PVSAT 0.03, spatial memory 0.003). Best prediction results were achieved with a rolling average of 200 predictions (102.4 s), during set activity types, mean absolute error for ‘walk up’ (MAE200 12.5%) and range of absolute error for ‘run down‘ (RAE200 16.7%). Conclusion: We were able to measure cognitive and physical fatigue using a single wearable sensor during a practical field protocol including contextual factors in conjunction with a neural network model. This research has practical application to fatigue research in the field.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Open domain question answering (OpenQA) tasks have been recently attracting more and more attention from the natural language processing (NLP) community. In this work, we present the first free-form multiple-choice OpenQA dataset for solving medical problems, MedQA, collected from the professional medical board exams. It covers three languages: English, simplified Chinese, and traditional Chinese, and contains 12,723, 34,251, and 14,123 questions for the three languages, respectively. We implement both rule-based and popular neural methods by sequentially combining a document retriever and a machine comprehension model. Through experiments, we find that even the current best method can only achieve 36.7%, 42.0%, and 70.1% of test accuracy on the English, traditional Chinese, and simplified Chinese questions, respectively. We expect MedQA to present great challenges to existing OpenQA systems and hope that it can serve as a platform to promote much stronger OpenQA models from the NLP community in the future.

This study aims to develop a performance evaluation system that can facilitate performance evaluation at region, hospital, and department levels to enable better cost management for sustainable development. A multi-level system of performance evaluation informs a hierarchical assessment of cost management from regions to hospitals to departments using diagnosis-related group (DRGs). Various metrics are developed employing the variances between targets and actuals where targets are determined from two perspectives: benchmarking using external regional prices and change management using internal data. Targets for the latter are statistically based and specifically incorporate variability. The model is applied to two hospitals, twenty departments, nine DRGs and 1071 inpatients. The analyses indicate that the approach can provide a practical evaluation tool that allows for particular characteristics at multiple levels. The system provides macro-micro and external-internal perspectives in performance, enabling high-level variances to be decomposed thereby identifying sources of performance variability and financial impact.

This paper presents an unsupervised feature selection method for multi-dimensional histogram-valued data. We define a multi-role measure, called the compactness, based on the concept size of given objects and/or clusters described by a fixed number of equal probability bin-rectangles. In each step of clustering, we agglomerate objects and/or clusters so as to minimize the compactness for the generated cluster. This means that the compactness plays the role of a similarity measure between objects and/or clusters to be merged. To minimize the compactness is equivalent to maximize the dis-similarity of the generated cluster, i.e., concept, against the whole concept in each step. In this sense, the compactness plays the role of cluster quality. We also show that the average compactness of each feature with respect to objects and/or clusters in several clustering steps is useful as feature effectiveness criterion. Features having small average compactness are mutually covariate, and are able to detect geometrically thin structure embedded in the given multi-dimensional histogram-valued data. We obtain thorough understandings of the given data by the visualization using dendrograms and scatter diagrams with respect to the selected informative features. We illustrate the effectiveness of the proposed method by using an artificial data set and real histogram-valued data sets.

A humidity-sensitive demand-controlled ventilation system is known for many years. It has been developed and commonly applied in regions with an oceanic climate. Some attempts were made to introduce this solution in Poland in a much severe continental climate. The article evaluates this system's performance and energy consumption applied in an 8-floor multi-unit residential building, virtual reference building described by the National Energy Conservation Agency NAPE, Poland. The simulations using the computer program CONTAM were performed for the whole hating season for Warsaw's climate. Besides passive stack ventilation that worked as a reference, two versions of humidity-sensitive demand-controlled ventilation were checked. The difference between them lies in applying the additional roof fans that convert the system to hybrid. The study confirmed that the application of demand-controlled ventilation in multi-unit residential buildings in a continental climate with warm summer (Dfb) leads to significant energy savings. However, the efforts to ensure acceptable indoor air quality require hybrid ventilation, which reduces the energy benefits. It is especially visible when primary energy use is analyzed.

Wound infections evidently appeared in times of World War I that accounted a significant mortality and morbidity rate among injured soldiers. Currently, around 11 million people worldwide require medical treatment for wound infections and 300,000 die every year due to untreated wound infection. The extensive use of antibiotics to treat wound infection leads to emerging new microbial strains that are resistant to many antibiotics. There is a growing concern on the emergence and re-emergence of drug-resistant pathogens such as multi-resistant bacterial strains. Hence, the development of new antimicrobial compounds or the modification of those that already exist to improve antibacterial activity is a high priority area of research. During the past few decades, nanotechnology has arisen with new promising technology for synthesis of nanobiomaterials. Metallic nanoparticles (NPs) are considered as new alternative treatment with superior antibacterial activity. In this study, new formulation of titanium oxide (TiO2) NPs with different sizes were synthesized and characterized. Genotoxicity, mutagenicity and antibacterial activities of TiO2 NPs against the causative agents of wound infection were investigated. Antibacterial activity of TiO2 NPs was conducted against three ATCC ® bacterial strains: methicillin-resistant Staphylococcus aureus (MRSA), Escherichia coli and Pseudomonas aeruginosa. The results clearly illustrate a superior antibacterial activity of all newly formulated TiO2 NPs against the most causative agents of wound infection. Most of our TiO2 NPs showed non-genotoxic and non-mutagenic results at the maximum concentrations. Findings of this study will enhance the future of the therapeutic strategies against the resistant pathogenic strains that cause wound infections.

Indian cities are increasingly becoming susceptible to PM10 induced health effects which have become a matter of concern for the policymakers of the country. Air pollution is engulfing the comparatively smaller cities as the rapid pace of urbanization, and economic development seems not to lose steam ever. A review of air pollution of 28 cities of India, which includes tier-I, II, and III cities of India, found to have grossly violated both WHO and NAAQS standards in respect of acceptable daily average PM10 concentrations by a wide margin. Predicting the city level PM10 concentrations in advance and accordingly initiate prior actions is an acceptable solution to save the city dwellers from PM10 induced health hazards. Predictive ability of three models, linear MLR, nonlinear MLP (ANN), and nonlinear CART, for one day ahead PM10 concentration forecasting of tier-II Guwahati city, were tested with 2016-2018 daily average observed climate data, PM10, and gaseous pollutants. The results show that the non-linear algorithm MLP with feedforward backpropagation network topologies of ANN class, giving the best prediction value when compared with linear MLR and nonlinear CART model. ANN (MLP) approach, therefore, may be useful to effectively derive a predictive understanding of one day ahead PM10 concentration level and thus provide a tool to the policymakers for improving decision-making associated with air pollution and public health.

The small satellite market continues to grow year after year. A compound annual growth rate of 17% is estimated during the period between 2020 and 2025. Low-cost satellites can send a vast amount of images to be post-processed at the ground to improve the quality and extract detailed information. In this domain lies the resolution enhancement task, where a low-resolution image is converted to a higher resolution automatically. Deep learning approaches to Super-Resolution (SR) reached the state-of-the-art in multiple benchmarks; however, most of them were studied in a single-frame fashion. With satellite imagery, multi-frame images can be obtained at different conditions giving the possibility to add more information per image and improve the final analysis. In this context, we developed and applied to the PROBA-V dataset of multi-frame satellite images a model that recently topped the European Space Agency’s Multi-frame Super Resolution (MFSR) competition. The model is based on proven methods that worked on 2D images tweaked to work on 3D: the Wide Activation Super Resolution (WDSR) family. We show that with a simple 3D CNN residual architecture with WDSR blocks and a frame permutation technique as data augmentation better scores can be achieved than with more complex models. Moreover, the model requires few hardware resources, both for training and evaluation, so it can be applied directly from a personal laptop.

The aim of this research is forwarded for assessment of provision possibilities of the multi-componential and heterogeneous services in the fast-changing topology of cargo transportation processes. The mobile intelligent services in nowadays transport means require the development of complex infrastructure for multi-compositional service support. Our objectives are related to the investigation in data-transfer capabilities for heterogeneous service support, by offering some improvements for developing the infrastructure of transportation of vehicles by helping in the administration of transport processes. This research aims to develop an approach for assessment of infrastructure for sustainable management of cargo transportation processes by roads. Such assessment is multi-layered by including the management possibilities of cargo transportation logistic processes and electronic (smart, mobile) services by implementing of nowadays innovative software and hardware of information communication technologies (ICT). Special attention is paid for road safety, more environment cleanable, and paperless management by assessing the integration of potentials and prospects of wireless, vehicle Ad-hoc communication networks (VANET), and other communication possibilities. Some requirements are revealed for such type of infrastructure for the provision of heterogeneous services. The results of the development of infrastructure demonstrate the capacities of the potential of wireless networks for the provision of high-level of multi-component, heterogeneous services.

Enhancing the effectiveness of search and rescue operation at sea is always a duty of utmost importance of the coastal states. The search area for distressed objects can be determined by using Monte Carlo simulation, combined with the Median-Filter. Once the search area has been identified, the success of search and rescue operations depends on the sweeping ability of search and rescue vessel at the probability area of the distress object with the minimum time. This is the important element to the success of the search and rescue operation as it minimizes the risk and cost for Search and rescue team. In this article, the authors study and propose the use of Bacterial Foraging Optimization Algorithm (BFOA) to calculate the optimal search and co-ordination route for many search and rescue vessels in Vietnam sea. The simulation results show that it is quite consistent with reality and BFOA can be effectively applied to determine a quick search.

There always exist steel cuttings, holes and cracks at the interfaces in the explosive composite plate. Multi-pass friction stir processing (M-FSP) is proposed in this research to optimize the interface microstructure and the interface connection for 1060Al/Q235 explosive composite plate. Results show that the microstructures of 1060Al after M-FSP are fine and uniform owing to the strong stirring effect and recrystallization. Micro-defects formed by the explosive welding can be repaired by the M-FSP. However, M-FSP can also form tunnel defects in the aluminum, especially when the passes are one and two. The melting block and the melting lump in the composite plates are easy to become source of crack. The shear strengths and the bending properties for the 1060Al/Q235 explosive composite plate after M-FSP are the best when the passes are three, with the tool rotation speed of 1200rpm and the forward speed of 60mm/min. The optimized interfaces for the explosive composite plate after M-FSP are mainly by the metallurgical bondings, with a certain thickness and are discontinuous. Therefore, the crack extension stress is the largest and the mechanical properties are the best.

In this paper, a multi-mode waveguide-based optical resonator is proposed for an integrated optical refractive index sensor. Conventional optical resonators have been studied for single-mode waveguide-based resonators to enhance the performance, but mass production is limited owing to the high fabrication costs of nano-scale structures. To overcome this problem, we designed an S-bend resonator based on a micro-scale multi-mode waveguide. In general, multi-mode waveguides cannot be utilized as optical resonators, because of a performance degradation resulting from modal dispersion and an output transmission with multi-peaks. Therefore, we exploited the mode discrimination phenomenon using the bending loss, and the resulting S-bend resonator yielded an output transmission without multi-peaks. This phenomenon is utilized to remove higher-order modes efficiently using the difference in the effective refractive index between the higher-order and fundamental modes. As a result, the resonator achieved a Q-factor and sensitivity of 2.3x10³ and 52 nm/RIU, respectively, using the variational finite-difference time-domain method. These results show that the multi-mode waveguide-based S-bend resonator with a wide line width can be utilized as a refractive index sensor.

Software defect prediction is an important means to guarantee software quality. Because there are no sufficient historical data within a project to train the classifier, cross-project defect prediction (CPDP) has been recognized as a fundamental approach. However, traditional defect prediction methods using feature attributes to represent samples, which can not avoid negative transferring, may result in poor performance model in CPDP. This paper proposes a multi-source cross-project defect prediction method based on dissimilarity space ( DM-CPDP). This method first uses the density-based clustering method to construct the prototype set with the cluster center of samples in the target set. Then, the arc-cosine kernel is used to form the dissimilarity space, and in this space the training set is obtained with the earth mover’s distance (EMD) method. For the unlabeled samples converted from the target set, the KNN algorithm is used to label those samples. Finally, we use TrAdaBoost method to establish the prediction model. The experimental results show that our approach has better performance than other traditional CPDP methods.

This study aims to understand the current state of research in urban resilience and to open a discussion about multi-level perspectives for this concept. Starting with the history of the concept of resilience, we identify three main stages in resilience concept’s evolution: conceptualization, contextualization and operationalization. Confusion occurs between sustainability and resilience, therefore we clearly separate these two concepts by creating conceptual maps. Such maps also underline the specificities of urban and regional resilience discourses. We illustrate that urban resilience research, operating within intra-urban processes, is oriented towards natural disasters, while regional resilience research, operating mostly within inter-urban processes, is oriented towards economic shocks. We show that these two approaches to resilience – urban and regional – are complementary, and we propose to integrate them into a multi-level perspective. By combining these two discourses, we propose a multi-level approach to urban resilience that takes into account both top-down and bottom-up resistance processes. In the discussion section, we propose to take the panarchy perspective as a theoretical framework for multi-level urban resilience, that explains the interactions between different levels through adaptive cycles, relationships between which can help to explain urban resilience.

The effect of hybrid carbon fillers of multi-walled carbon nanotubes (CNT) and carbon black (CB) on the electrical and morphological properties of polystyrene (PS) nanocomposites were systematically investigated in microinjection molding (μIM). The polymer nanocomposites with three different filler concentrations (i.e. 3, 5 and 10 wt%) at various weight ratios of CNT/CB (100/0, 30/70, 50/50, 70/30, 0/100) were prepared by melt blending, then followed by μIM under a defined set of processing conditions. A rectangular mold insert which has three consecutive zones with decreasing thickness along the flow direction was adopted to study abrupt changes in mold geometry on the properties of resultant microparts. The distribution of carbon fillers within microparts was observed by scanning electron microscope, which was correlated with electrical conductivity measurements. Results indicated that there is a flow-induced orientation of incorporated carbon fillers and this orientation increased with increasing shearing effect along the flow direction. High structure CB is found to be more effective than CNT in terms of enhancing the electrical conductivity, which was attributed to the good dispersion of CB in PS and their ability to form conductive networks via self-assembly. Morphology observations indicated that there is a shear-induced depletion of CB particles in the shear layer, which is due to the marked difference of shear rates between the shear and core layers of the molded microparts. Moreover, an annealing treatment is beneficial to enhance the electrical conductivity of CNT-containing microparts.

The value of an NBA basketball player varies at each crucial point in time, depending on the player’s career and performance. This study constructs a player’s value assessment model. The model comprises two parts. First, from an objective perspective, entropy is employed to measure each player’s achievement in five categories—rebounds, assists, steals, blocked shots, and scores. The total entropy assessment value is calculated and then combined with the players’ scores to develop a player's value matrix to assess the relative value model among players of the same type.

Geometric Akaike Information Criteria (G-AICs) for generalized noise-level dependent crystallographic symmetry classifications of two-dimensional (2D) images that are more or less periodic in either two or one dimensions as well as Akaike weights for multi-model inferences and predictions are reviewed. Such novel classifications do not refer to a single crystallographic symmetry class exclusively in a qualitative and definitive way. Instead, they are quantitative, spread over a range of crystallographic symmetry classes, and provide opportunities for inferences from all classes (within the range) simultaneously. The novel classifications are based on information theory and depend only on information that has been extracted from the images themselves by means of maximal likelihood approaches so that these classifications are objective. This is in stark contrast to the common practice whereby arbitrarily set thresholds or null hypothesis tests are employed to force crystallographic symmetry classifications into apparently definitive/exclusive states, while the geometric feature extraction results on which they depend are never definitive in the presence of generalized noise, i.e. in all real world applications. Thus, there is unnecessary subjectivity in the currently practiced ways of making crystallographic symmetry classifications, which can be overcome by the approach outlined in this review.

The paper investigates some similarity measures in interval bipolar neutrosophic environment for multi-attribute decision making problems. At first, we define Hamming and Euclidean distances measures between interval bipolar neutrosophic sets and establish their basic properties. We also propose two similarity measures based on the Hamming and Euclidean distance functions. Using maximum and minimum operators, we define new similarity measures and prove their basic properties. Using the proposed similarity measures, we propose a novel multi attribute decision making strategy in interval bipolar neutrosophic set environment. Lastly, we solve an illustrative example of multi attribute decision making and present comparison analysis to show the feasibility, applicability and effectiveness of the proposed strategy.

Coastal areas are increasingly being damaged with the expansion of seawater intrusion areas. We suggest a three-step method for reducing seawater intrusion areas by predicting future damage to groundwater being used continuously. First, the area most vulnerable to seawater intrusion damage is selected from among 25 areas on the west coast of the Republic of Korea. Having identified the Taean area as the region in question in the second step, we use RCP 4.5 and 8.5 as future sea level rise scenarios and predict the future usage of groundwater using linear-regression analysis of data for the past 10 years. Consequently, for RCP 8.5 (groundwater-usage scenario 1.0), 68.5% of the total Taean area is projected to be influenced by seawater intrusion. In the third step, the effectiveness of seawater intrusion reduction measures is analyzed considering the projected future situation and the local characteristics of the Taean area. After considering the effects of alternative locations, as well as seawater intrusion related data, alternatives were prioritized using a multi-criteria decision-making method. Consequently, 3, 5, and 4 were prioritized in the listed order, and we judged that by applying seawater intrusion area reduction measures according to this result, we will achieve the biggest effect.

10% copper substituted (BiCUVOX/Bi₂V_0.9Cu_0.1O_5.5−δ) and 5% copper/titanium double-substituted bismuth vanadate (BiCUTIVOX/Bi₂V_0.9(Cu_0.05Ti_0.05)O_5.5−δ) platelets were formed by molten salt synthesis (MSS) using a eutectic KCl/NaCl salt mixture. The product was phase pure within the limits of X-ray diffraction. The size and form of the platelets could be controlled by changing the heating temperature and time. The crystallite growth rate at a synthesis temperature of 650 °C, and activation energy for grain growth were determined for BICUTIVOX, which experienced inhibited growth compared to BICUVOX. Quasi-equilibrium, multi-foil shapes consisting of lobes around the perimeter of the platelets were observed and explained in the context of relative two-dimensional nucleation and edge growth rates.

Sensitivity to weather conditions, and specially to clouds, is a severe limiting factor to the use of optical remote sensing for Earth monitoring applications. A possible alternative, is to resort to weather-insensitive synthetic aperture radar (SAR) images. However, in many real-world applications, critical decisions are made based on some informative spectral features, such as water, vegetation or soil indices, which cannot be extracted from SAR images. In the absence of optical sources, these data must be estimated. The current practice is to perform linear interpolation between data available at temporally close time instants. In this work, we propose to estimate missing spectral features through data fusion and deep-learning. Several sources of information are taken into account - optical sequences, SAR sequences, DEM - so as to exploit both temporal and cross-sensor dependencies. Based on these data, and a tiny cloud-free fraction of the target image, a compact convolutional neural network (CNN) is trained to perform the desired estimation. To validate the proposed approach, we focus on the estimation of the normalized difference vegetation index (NDVI), using coupled Sentinel-1 and Sentinel-2 time-series acquired over an agricultural region of Burkina Faso from May to November 2016. Several fusion schemes are considered, causal and non-causal, single-sensor or joint-sensor, corresponding to different operating conditions. Experimental results are very promising, showing a significant gain over baselines methods according to all performance indicators.

The bottleneck in creating dynamic models of biological networks and processes often lies in estimating unknown kinetic model parameters from experimental data. In this regard, experimental conditions have a strong influence on parameter identifiability and should therefore be optimized to give the maximum information for parameter estimation. Existing model-based design of experiment (MBDOE) methods commonly rely on the Fisher Information Matrix (FIM) for defining a metric of data informativeness. When the model behavior is highly nonlinear, FIM-based criteria may lead to suboptimal designs since the FIM only accounts for the linear variation of the model outputs with respect to the parameters. In this work, we developed a multi-objective optimization (MOO) MBDOE, where model nonlinearity was taken into consideration through the use of curvature. The proposed MOO MBDOE involved maximizing data informativeness using a FIM-based metric and at the same time minimizing the model curvature. We demonstrated the advantages of the MOO MBDOE over existing FIM-based and other curvature-based MBDOEs in an application to the kinetic modeling of fed-batch fermentation of Baker's yeast.

Background: Appendicular skeletal muscle (or lean) mass (ALM) estimated using dual-energy X-ray absorptiometry (DXA) is considered to be a preferred method for sarcopenia studies. However, DXA is expensive, has limited portability, and requires radiation exposure. Bioelectrical impedance analysis (BIA) is inexpensive, easy to use, and portable; thus BIA might be useful in sarcopenia investigations. However, a large variety of models have been commercially supplied by different companies, and for most consumer products, the equations estimating ALM are not disclosed. It is therefore difficult to use these equations for research purposes. In particular, the BIA equation is often age-dependent, which leads to fundamental difficulty in examining age-related ALM loss. The aims of the current study were as follows: (1) to develop and validate an equation to estimate ALM using multi-frequency BIA (MF-BIA) based on theoretical models, and (2) to establish sarcopenia cutoff values using the equation for the Japanese population. Methods: We measured height (Ht), weight, and ALM obtained using DXA and a standing-posture 8-electrode MF-BIA (5, 50, 250 kHz) in 756 Japanese individuals aged 18 to 86-years-old (222 men and 301 women as developing equation group and 97 men and 136 women as a cross validation group). The traditional impedance index (Ht²/Z₅₀) and impedance ratio of high and low frequency (Z₂₅₀/Z₅) of hand to foot values were calculated. Multiple regression analyses were conducted with ALM as dependent variable in men and women separately. Results: We created the following equations: ALM = (0.6947 × (Ht²/Z₅₀)) + (−55.24 × (Z₂₅₀/Z₅)) + (−10,940 × (1/Z₅₀)) + 51.33 for men, and ALM = (0.6144 × (Ht²/Z₅₀)) + (−36.61 × (Z₂₅₀/Z₅)) + (−9332 × (1/Z₅₀)) + 37.91 for women. Additionally, we conducted measurements in 1624 men and 1368 women aged 18 to 40 years to establish sarcopenia cutoff values in the Japanese population. The mean values minus 2 standard deviations of the skeletal muscle mass index (ALM/Ht²) in these participants were 6.8 and 5.7 kg/m² in men and women, respectively. Conclusion: The current study established and validated a theoretical and age-independent equation using MF-BIA to estimate ALM and provided reasonable sarcopenia cutoff values.

This paper presents experimental identification and vibration suppression of a flexible manipulator with non-collocated piezoelectric actuators and strain sensors using optimal multi-poles placement control. To precisely identify the system model, a reduced order transfer function with relocated zeros is proposed, and a first-order inertia element is added to the model to compensate the non-collocation. Comparisons show the identified model match closely with the experimental results both in the time and frequency domains, and a fit of 97.2% is achieved. Based on the identified model, a full-state multi-poles placement controller is designed, and the optimal locations of the closed loop poles are determined. The feasibility of the proposed controller is validated by simulations. Moreover, the controller is tested for different locations of the closed loop poles, and an excellent performance of the optimal locations of the closed loop poles is shown. Finally, the effectiveness of the proposed controller is demonstrated by experiments. Results show that the vibrations of the expected modes are significantly diminished. Besides, vibrations of the higher modes are also slightly suppressed. Accordingly, multi-mode vibrations of the manipulator are well attenuated, and the tip displacement converges quickly with the proposed method.

Organisms in the wild have cryptic life stages that are sensitive to changing environmental conditions and can be difficult to survey. In this study, I used mark-recapture methods to repeatedly survey Anaea aidea (Nymphalidae) caterpillars in nature, then modeled caterpillar demography as a hidden Markov process to assess if temporal variability in temperature and density influence the survival and growth of A. aidea over time. Individual encounter histories result from the joint likelihood of being alive and observed in a particular stage, and I included hidden states by separating demography and observations into parallel and independent processes. I constructed a demographic matrix containing the probabilities of all possible fates for each stage, including hidden states, e.g., eggs and pupae. I observed both dead and live caterpillars with high probability. Peak caterpillar abundance attracted multiple predators, and survival of fifth instars declined as per capita predation rate increased through spring. A time lag between predator and prey abundance was likely the cause of improved fifth instar survival estimated at high density. Growth rates showed an increase with temperature, but the most likely model did not include temperature. This work illustrates how state-space models can include unobservable stages and hidden state processes to evaluate how environmental factors influence vital rates of cryptic life stages in the wild.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

Unmanned aerial vehicles (UAVs) have increasingly become integral to multi-access edge computing (MEC) due to their flexibility and cost-effectiveness, especially in the B5G and 6G eras. This paper aims to enhance the Quality of Experience (QoE) in large-scale UAV-MEC networks by minimizing the shrinkage ratio through optimal decision-making in computation mode selection for each user device (UD), UAV flight trajectory, bandwidth allocation, and computing resource allocation at edge servers. However, the interdependencies among UAV trajectory, binary task offloading mode, and computing/network resource allocation across numerous IoT nodes pose significant challenges. To address these challenges, we formulate the shrinkage ratio minimization problem as a mixed-integer nonlinear programming (MINLP) problem and propose a two-tier optimization strategy. To reduce the scale of the optimization problem, we first design a low-complexity UAV partition coverage algorithm based on the Welzl method and determine the UAV flight trajectory by solving a Traveling Salesman Problem (TSP). Subsequently, we develop a coordinate descent (CD) based method and an alternating direction method of multipliers (ADMM) based method for network bandwidth and computing resource allocation in the MEC system. The CD-based method is simple to implement and has a low computational complexity, while the ADMM-based method can further enhance the optimization result through joint optimization. Extensive simulations demonstrate that our proposed algorithms perform well in large-scale edge networks and outperform other representative benchmark methods.

Current trends in systemic risk literature provide new insights into multi-hazard risks that interact and compound with built environments, creating more significant impacts on socio-economic and human systems. Recurrent natural hazards and extreme weather events are more likely to compound and cascade into more impactful events, especially in vulnerable societies. In small-island communities (SICS), including large archipelagos and Small Island Developing States (SIDS), the long-term impact of multi-, compounding-, and cascading-hazards (MCC hazards) can result in persistent vulnerability and residual risks. This is due to delayed responses, limited resources, poverty, fewer evacuation options, and inadequate markets and infrastructure. Using Ternate, a densely populated small volcanic island in North Maluku, Indonesia, as a case study, this paper assesses the impacts of seven types of natural hazards: flash floods, landslides, extreme weather, extreme waves and abrasion, earthquakes, tsunamis, and volcanic eruptions. The research focuses on the multi-hazard impact on population, land use, and infrastructure exposures in 60 villages in Ternate. The findings highlight population density, land use, and infrastructure exposure to multi-hazard risks, providing valuable information on potential losses in future hazard events.

To curb the impacts arising from the agricultural sector the actions undertaken by policymakers, and ultimately by the farmers, are of paramount importance. However, finding the best strategy to reduce impacts, and especially assessing the effects of the interactions and mutual influence among farmers, is very difficult. To this aim, this paper shows an application of an agent-based model (ABM) coupled with life cycle assessment (LCA), which also includes multi objective optimization of farming activities (including both crop cultivation and livestock breeding) from an economic and environmental perspective. The environmental impacts are assessed using the impact assessment scores calculated with the Environmental Footprint (EF) 3.0 life cycle impact assessment (LCIA) method and the study is conducted “from cradle to farm gate”. The model is applied to all the farms in Luxembourg, whose network is constructed utilizing neighborhood interactions, through which a parameter known as farmer's green consciousness (GC) is updated at each time step. The optimization module is instantiated at the end of each time step, and decision variables (the number of livestock units and land allocation) are assigned based on profitability and specified environmental impact categories. If only profit optimization is considered (i.e. when farmers’ GC is de-activated), the results show a 9% reduction in the aggregated environmental impacts (obtained as EF “single score”) and a 5.5% increase in overall profitability. At the farm level, simulations display a clear trade-off between environmental sustainability and financial stability, with a 25% reduction in overall emissions possible if farming activities are carried using the EF single score impact in the objective function, though this results in an 8% reduction in profitability over ten years.

Melanin is extensively distributed in organisms and believed to be synthetized by tyrosinase (TYR), leading to aberrant coloring and skin conditions when over-produced. Loquat (Eriobotrya japonica (Thunb.) Lindl.) flowers contain large amounts of bioactive substances currently few studied on their suppressive capabilities to melanin synthesis. Its isolate product (LFP) was obtained by ethanol solution extraction and resin purification, of which the inhibitory mechanism on TYR activity was elaborated by enzyme kinetics and multi-spectroscopy determinations and the impact on related proteins’ expression in mouse melanoma B16 cells was analyzed with Western blotting. HPLC-MS analysis indicated that LFP was identified into 137 compounds, with 12 including flavonoids (quercetin, isorhamnoin, p-coumaric acid, etc.), cinnamic acid and its derivatives as well as benzene and its derivatives owning TYR inhibitory activities. LFP inhibited TYR activity in a concentration-dependent manner with its IC50 value being 2.8 mg/mL and an anti-competitive mechanism involved altering the enzyme's conformation. LFP reduced the expression of TYR, TRP1, and TRP2 in melanoma B16 cells, hence inhibiting the synthesis of melanin. Considered collectively, LFP would be a viable option for treating hyperpigmentation caused by tyrosinase, providing a theoretical basis for the value-added utilization of loquat flower resource in beauty and aging related functional products.

The quality of healthcare services is a very important indicator of social welfare in developed and emerging countries. Good quality levels are critical to ensuring patient safety, improving health outcomes, increasing patient satisfaction, optimizing resource utilization, and meeting regulatory requirements. The stable and sustainable operation of medical institutions urgently requires the establishment of a reliable and effective medical quality performance evaluation platform. However, the complexity of the evaluation process, involving numerous evaluators and the consideration of different subjective and objective criteria, poses significant challenges and essentially constitutes a group multi-criteria decision-making problem. This article uses the overall medical environment of the institution, medical service attitude, medical security, administrative service measures, etc. as measurement standards to deal with this challenge. It proposes a medical service quality measurement model suitable for both qualitative and quantitative analysis. In view of the heterogeneity of information, the two-tuple fuzzy language calculation method is introduced to enable evaluators to skillfully manage diverse information and effectively avoid potential information omission problems in the subjective evaluation integration process. The effectiveness and feasibility of the model were demonstrated by applying it to the operational framework of a medical institution in central Taiwan.

This paper is devoted to the study of multi-dimensional integral transform with Fox H-function in the kernel in weighted spaces integrable functions in the domain R+n with positive coordinates. Mapping properties such as the boundedness, the range, the representations of the considered transformation are established.

Wind turbines (WTs) are clean a renewable energy source that has been growing in popularity in recent years. Gearboxes are complex, expensive, and critical components of WT, which are subject to high maintenance costs and several stresses including high loads and harsh environments that can lead to failure with significant downtime and financial losses. This paper focuses on the development of a digital twin-based approach for the modelling and simulation of WT gearboxes with the aim to improve their design, diagnosis, operation, and maintenance by providing insights into their behavior under different operating conditions. Pow-erful commercial computer-aided design tools (CAD) and computer-aided engineering (CAE) software are embedded into a computationally efficient multi-objective optimization framework (modeFrontier) with the aim of maximizing the power density, compactness, performance, and reliability of the WT gearbox. This entails minimizing its weight, volume, and maximum stresses and strains achieved without compromising efficiency. The 3D CAD model of the WT gearbox is carried out using SolidWorks, the Finite Element Analysis (FEA) to obtain the stresses and strains fields are modelled using Ansys Workbench, while the multibody kinematic and dynamic system is analyzed using MSC Adams. The method has been successfully applied to different case studies to find the optimal design and analyze the performance of the WT gearboxes. Simulation results can be used to identify potential failure modes and optimize gearbox design to improve performance, extend service life and relia-bility, thereby ensuring proper operation over its lifetime and reducing maintenance costs.

Background: Locally advanced rectal cancers (10-20%) can present with infiltration into adjacent viscera. R0 resections remain the key factor for better survival. Traditionally these cases have been managed with open surgery. There are some limitations of laparoscopic surgery in these case, which can potentially be overcome by robotic surgery. Objectives: To determine the feasibility and outcome results of robotic multi-visceral resection of stage T4 rectal carcinoma. Methods: Consecutive patients having locally advanced carcinoma of rectum, who undergone robotic multi-visceral resection as the primary treatment between 2015 -2018 were included, through our database which was maintained prospectively. All perioperative and intraoperative parameters were analyzed. Patient demographics, co-morbidities, preoperative imaging, endoscopic findings, operative data, histopathology results, postoperative hospital course and procedure related postoperative adverse events were noted and analyzed. Results: Twenty-one patients with the diagnosis of nonmetastatic locally advanced rectal cancers were operated with Robotic Si/X platform. The median body mass index was 28.5 kg/m2 (range 21-42). The mean blood loss during operation was 20 ml (range 5-200), and the mean duration of surgery was 280 min (range 240-430). The median hospital stay after operation was 6 days (range 4-25 days). On postoperative histopathology, R0 resection rate was 90.5% (19/21). Conclusions: The robotic multi-visceral en-bloc resection of stage T4 rectal carcinoma is technically feasible and oncologically safe. Advanced technical skills, accurate radiological staging and careful patient selection can allow the extension of minimal access surgery to this challenging group of patients.

In order to solve the problem of fault diagnosis for CNC machine feed system under the condition of variable speed conditions, an intelligent fault diagnosis method based on multi-domain feature extraction and ensemble learning model is proposed. First, various monitoring signals including vibration signal, noise signal and current signal are collected. Then, the monitoring signals are preprocessed and the time-domain, frequency-domain and time-frequency domain feature indexes are extracted to construct a multi-dimensional mixed domain feature set. Finally, the feature set is putting into the constructed DoubleEnsemble-LightGBM model to realize the fault diagnosis of the feed system. The experimental results show that the model can achieve good diagnosis results under different working conditions for both the public data set and the feed system test bench data set, and the average overall accuracy is 91.07% and 98.06% respectively. Compared with XGBoost and other advanced ensemble learning models, the method has better accuracy. It provides technical support for the stable operation and intelligent of CNC machine tools..

This study investigated the presence, distribution, and antimicrobial resistance profiles of extend-ed-spectrum beta-lactamase (ESBL)-producing Enterobacteriaceae in a dairy herd located in Northern Italy. A questionnaire was administered, and the feces of clinically healthy pre-weaned dairy calves, their mothers, and the cows treated for mastitis, waste milk, water, and environmental samples, were collected and inoculated on Chromagar ESBL™ medium. The questionnaire identi-fied several risk factors including administration of waste milk to male calves, lack of routine cleaning of calf feeding and housing equipment, and blanket dry cow therapy. Escherichia coli was identified by MALDI-TOF MS in the feces of 28 of 37 (75.67%) calves, 2 of 3 (66.67%) treated cows, 8 of 14 (57.15%) environmental samples, and the waste milk. Six of 14 (42.85%) environmental samples were also positive for ESBL Acinetobacter baumannii, while all fecal samples were negative. ESBL production was confirmed for all E. coli isolates based on the double disk susceptibility test (DDST), while none were carbapenemase producers. Upon minimal inhibitory concentration (MIC) analysis, all of them showed multiple resistances and were categorized as multi-drug resistant (MDR). This study confirms the widespread presence of MDR, ESBL-E. coli in dairy calves and highlights their diffusion in the farm environment.

Pedestrian object detection plays a significant role in intelligent systems such as intelligent traffic and monitoring. Traditional machine learning methods on pedestrian detection have shown various drawbacks, \eg{} low accuracy, slow speed, \etc The Convolutional Neural Network (CNN) based object detection algorithms have demonstrated remarkable advantages in the field of pedestrian detection. However, the mainstream CNNs still face the problems of slow speed and low detection accuracy, especially on small and occluded targets from aerial perspective. In this paper, we propose Multi-Scale Attention YOLO (MSA-YOLO) detection algorithm to address the above issues. MSA-YOLO includes a Squeeze, Excitation and Cross Stage Partial (SECSP) channel attention module for CNNs to extract richer pedestrian features with a small number of extra parameters. It also contains a multi-scale prediction module to capture the information among different pedestrian scales, which can recognize the small objects with higher accuracy and significantly reduce the missed detection. To sufficiently evaluate our proposed model, we manually collect and annotate a new benchmark dataset, Luoyang Pedestrian Dataset \footnote{The dataset can be downloaded through this anonymous link: \url{https://drive.google.com/drive/folders/13po1FX7Qk5RDgb60-dzOi74cq_kqDJtM?usp=sharing} }, which has much more sample annotations, features, scenes and image view angles than the existing benchmark datasets. In addition, the images in our dataset have higher resolution than most of benchmark pedestrian detection datasets, which can provide more detailed features of pedestrians and thus improve the model performance. When tested on Luoyang Pedestrian Dataset, our proposed MSA-YOLO algorithm significantly outperform the most commonly used baseline models with almost the same model size. This shows the efficiency of our proposed model. (The code and new dataset will be released to the public later.)

The utilization of smart IoT devices, commonly referred to as digital twins, is aimed at the digitalization of human knowledge within aquaculture processes. This involves the incorporation of cutting-edge technologies, including information-based management with big data and modeling, to automate machinery and gain comprehensive insights into the aquaculture environment and fish farm conditions. The ultimate objective is to empower farmers to make informed decisions, furnishing them with objective data to enhance their capacity in monitoring and controlling the various factors impacting fish production. As a result, farming decisions can be fine-tuned to enhance fish health and optimize farm output. In the context of large and modern aquaculture farms, technological innovation becomes imperative to automate processes, minimize labor requirements, and streamline fish feeding operations. Remarkably, the literature currently offers limited discussions on the digital transformation of aquaculture through the application of digital twin methodologies. A prior study underscores the critical influence of factors such as market prices and fish survival rates on the profitability of offshore caging culture. In this study, we embark on an analysis of the prerequisites for establishing a digital twin infrastructure tailored to intelligent fish feeding management. This infrastructure is designed to facilitate the integration of technology and data-driven decision-making, ultimately enhancing the efficiency of fish feeding processes. The proposed architecture for the fish feeding digital twin encompasses various digital twin components, encompassing water quality forecasting, fish population assessment, fish metrics estimation, fish feed prediction, and evaluation of fish feeding intensity. Furthermore, we optimize the daily fish feeding process through reinforcement learning algorithms. Finally, we implement a cloud-based AIoT system that provides the runtime environment for executing digital twins and controlling our intelligent fish feeding machinery. Experimental findings underscore the efficacy of the proposed digital twin system in significantly improving traditional fish feeding processes, notably in terms of reducing food costs and labor requirements.

Spectral image analysis has the potential to replace traditional approaches for assessing plant responses to different types of stress including herbicide, through non-destructive and high-throughput screening (HTS). Therefore, this study was conducted to develop a rapid bioassay method using a multi-well plate and spectral image analysis for diagnosis of herbicide activity and mode of action. Crabgrass (Digitaria ciliaris) as a model weed was cultivated in multi-well plates and subsequently treated with 6 herbicides with different modes of action when they reached the 1-leaf stage, using only a quarter of the recommended dose. To detect plant response to herbicides, plant spectral images were acquired after herbicide treatment using RGB, infrared (IR) thermal, and chlorophyll fluorescence (CF) sensors and analyzed for diagnosing herbicide efficacy and mode of action. Principal Component Analysis (PCA) using all spectral data successfully distinguished herbicides and clustered depending on their modes of action. The performed experiments have shown that the multi-well plate assay combined with spectral image analysis can be successfully applied for herbicide bioassay. In addition, the use of spectral image sensors, especially in CF image, would facilitate HTS by enabling rapid observation of herbicide response, as early as 3 hours after herbicide treatment.

Energy communities are key actors in the energy transition since they optimally interconnect renewable energy capacities with the consumers. Despite versatile objectives, they usually aim at improving the self-consumption of renewable electricity within low voltage grids to maximize revenues. In addition, energy communities are an excellent opportunity to supply renewable electricity to regional and national energy systems. However, effective price signals have to be designed to coordinate the needs of the energy infrastructure with the interests of these local stakeholders. The aim of this paper is to demonstrate the integration of energy communities at the national level with a bottom-up approach. District energy systems with a building scale resolution are modelled in a mixed integer linear programming problem. The Dantzig-Wolfe decomposition is applied to reduce the computational time. The methodology lies within the framework of renewable energy hub, characterized by a high share of photovoltaic capacities. Both investments into equipment and its operation are considered. The model is applied on a set of five typical districts and weather locations representative of the Swiss building stock. The extrapolation to the national scale revealed a heterogeneous photovoltaic potential throughout the country. Present electricity tariffs promote a maximal investment into photovoltaic panels in every region, reaching an installed capacity of 67.2 GW and generating 80 TWh per year. Since the national PV capacity needed is forecast at 15.4 GW peak, coordinated investments between local and national actors are needed to prevent dispensable expenses. An uncoordinated design is expected to increase the total costs for residential energy systems by 43.2% and curtails 48.2% of local renewable electricity.

Background Candida auris is an emerging multidrug-resistant fungal pathogen that represents a serious threat to healthcare settings currently. Objective: Its objective was to determine the prevalence of C. auris in the hospital since its initial detection in late 2019. Methods: Using an adapted risk assessment tool, we reviewed the charts. and medical files of all suspected? and confirmed cases of C. auris cases reported at King Khalid University Hospital, Riyadh between November 2019 and December 2022. Anonymized data were retrieved in a pre-established datasheet and analyzed to determine the epidemiological characteristics of C. auris infection in our facility. We established our initial prevalence by age, gender, risk factors, and according to sampling source. Results: Of the 53 confirmed cases positive for C. auris during the study period, 33 (62%) were males. Their ages ranged between 15 and 98; most positive cases occurred in 50 and above. Only one of the confirmed cases was hospital-acquired. All patients had at least one risk factor, and Urine samples yielded the greatest number of positive cases while admission to healthcare facilities constituted the highest risk in our study. Conclusion: Establishing a local prevalence could serve as our baseline/benchmark to compare with regional and international benchmarks.

This study presents a research plan that utilizes data obtained from wearable devices to identify human activities and gain insights into human behavior. We developed a model capable of classifying activities similar to human behavior and evaluated the effectiveness and generalization capabilities of this model. The data underwent initial preprocessing, including standardization and normalization. Additionally, recognizing the inherent similarities between human activity behaviors, we introduced a multi-layer classifier model. The first layer is a random forest model based on stepwise regression, which may encounter reduced accuracy for similar activities. The second layer employs a Support Vector Machine (SVM) model based on Kernel Fisher Discriminant Analysis (KFDA). KFDA is used to reduce the dimensionality of data points with potential confusion, followed by SVM for classification. The model was experimentally evaluated and applied to four benchmark datasets: UCI DSA, UCI HAR, WISDM, and IM-WSHA. The experimental results demonstrate that our approach achieved recognition accuracies of 99.71%, 98.71%, 99.12%, and 97.6% on these datasets, indicating excellent recognition performance. Furthermore, to assess the model's generalization ability, we performed K-fold cross-validation on the random forest model and utilized ROC curves for the SVM classifier. The results indicate that our multi-layer classifier model exhibits robust generalization capabilities.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

Underwater robotics equipped with visual detection systems have the function of detecting un-derwater artifacts, which is of great significance to deep-sea archaeology. Underwater artifacts are located in complex environments with poor imaging conditions, and the targets have chal-lenging problems such as breakage, stacking, and sediment burial, which causes the marine cul-tural target detection failures. To solve these problems, this paper proposes an underwater cul-tural target detection algorithm based on the deformable deep aggregation network model for underwater robotics exploration. To fully extract the target feature information of underwater targets in complex environments, this paper designs a multi-scale deep aggregation network with deformable convolutional layers. Besides, the BAM attention module is designed for fea-ture optimization, which enhances the potential feature information of the target while weak-ening the background interference information. Finally, the target prediction is achieved through feature fusion at different scales. The proposed algorithm has been extensively validat-ed and analyzed on the collected underwater artifact datasets, and the precision, recall, and mAP of the algorithm have reached 93.1%, 91.4%, and 92.8%, respectively. In addition, the present al-gorithm has been practically deployed on the underwater robotics. In the deep-sea tests, the ar-tifact detection frame rate reaches up to 19 fps, which satisfies the real-time target detection。

The electricity generated from fossil fuel and nuclear energy has negative impacts on the environment and has shown a need to search for and promote the use of clean, renewable and sustainable energy resources such as wind, solar and geothermal resources. Nowadays, wind energy resource has emerged as the fastest-growing source of energy on an overall scale. However, the selection of the best location for constructing a wind farm is a vital issue that can be considered a site selection problem, which involves various conflicting factors. Therefore, it is classified as a multi-criteria decision-making (MCDM) problem. In this research, the site selection of wind power plants is conducted in Burundi country. The Fuzzy Analytic Hierarchy Process (FAHP) was used to weigh the criteria considering their relative importance. The main factors affecting optimal wind farm location considered in this study are wind speed, slope, distance from the grid network, distance to roads, and land use/land cover (LULC). Furthermore, a geographic information system (GIS) is utilized to generate the final suitability wind farm locations map. The obtained results show that 20.91% of the total study area is suitable; nevertheless, only 1.96% is highly suitable for wind farm placement. The western part of Burundi is concluded to be the most suitable area for wind farm construction and the most area is situated in Lake Tanganyika.

Non-alcoholic steatohepatitis (NASH) is a complex disease resulting from chronic liver injury associated with obesity, type 2 diabetes, and inflammation. Recently, multi-target drugs have been proposed to treat complex diseases including NASH; however, their manufacturing pro-cesses remain time- and cost-intensive and inefficient. Therefore, to overcome these limitations, we developed UniStac, a novel enzyme-mediated conjugation platform for multi-specific drug development. UniStac demonstrated high conjugation yields, optimal thermal stabilities, and robust biological activities. Through such platform, we designed a tetra-specific compound, C-192, targeting Glucagon-like peptide 1 (GLP-1), Glucagon (GCG), Fibroblast growth factor 21 (FGF21), and Interleukin-1 receptor antagonist (IL-1RA) simultaneously for the treatment of NASH. The biological activity and treatment efficacy of C-192 were confirmed both in vitro and in vivo using a methionine–choline-deficient (MCD) diet-induced mouse model. C-192 exhibited profound therapeutic efficacies compared to conventional drugs, including liraglutide and dulaglutide. C-192 significantly improved alanine transaminase levels, triglyceride accumula-tion, and the non-alcoholic fatty liver disease activity score. Our results collectively provide clin-ical feasibility of UniStac for developing multi-specific drugs, and C-192 as an innovative thera-peutic opportunity for severe NASH, as it exerts synergistic effects across multiple targets.

The performance of bearings plays a pivotal role in determining the dependability and security of rotating machinery. In intricate systems demanding exceptional reliability and safety, the ability to accurately forecast fault occurrences during operation holds profound significance. Such predictions serve as invaluable guides for crafting well-considered reliability strategies and executing maintenance practices aimed at enhancing reliability. In order to ensure the reliability of bearing operation, this article investigates the application of three advanced techniques—Maximum Correlation Kurtosis Deconvolution (MCKD), Multi-Scale Permutation Entropy (MPE), and Long Short-Term Memory (LSTM) recurrent neural networks—for the prediction of the remaining useful life (RUL) of rolling bearings. Each technique's principles, methodologies, and applications are comprehensively reviewed, offering insights into their respective strengths and limitations. Case studies and experimental evaluations are presented to assess their performance in RUL prediction. Findings reveal that MCKD enhances fault signatures, MPE captures complexity, and LSTM excels in modeling temporal patterns. The root mean square error of the prediction results is 0.007. The fusion of these techniques offers a comprehensive approach to RUL prediction, leveraging their unique attributes for more accurate and reliable predictions.

Agriculture uses a lot of fuel, fertilizers, pesticides and other substances, while emitting large amounts of GHGs. It is important to optimize these inputs and outputs. One such way is increas-ing crop biodiversity. For this reason, single crops and mixtures of maize, hemp and faba bean as binary and ternary crops were investigated at the Experimental Station of Vytautas Magnus Uni-versity, Lithuania. Results showed that consumption of diesel fuel was by the 31-46% higher than in single and 22-35% higher than in binary cultivations was found in a ternary crop. This influenced on the highest energy input or near twice higher than in maize and hemp single crops and maize+hemp binary crop, but similar with binary crops with faba bean. Despite this, the productivity of the trinary crop and, at the same time, the energy output were 2-5 times higher than in other treat-ments. This compensated for higher energy inputs and the energy efficiency ratio. In ternary crop, energy productivity was from 1.1 to 2.8 times higher and net energy was by 1.9-5.3 times higher than in other tested cultivations. The highest total GHG emissions were obtained in binary maize+hemp and maize+faba bean cultivations (1729.84 and 2067.33 CO2eq ha-1). Ternary cultiva-tion with the highest energy inputs initiated average GHG emission - 1541.90 kg ha-1 CO2eq. For higher efficiency, ternary crop could be sown and harvested in one machine pass. Faba beans should be included in the ter-nary crops, as their biomass takes a significant part of the total biomass produced. We recommend to review the inter-cropped faba bean seeding rates as faba bean seeds have a high energy input equivalent.

It is important for food recognition to separate each ingredient within a food image at the pixel level. In this paper, we propose a new approach to segment ingredients by utilizing a CNN-based Single-Ingredient Classification Model. In detail, we firstly introduce a standardized biological-based hierarchical ingredient structure and construct a single-ingredient image dataset based on this structure. Then, we build a single-ingredient classification model based on a novel convolutional neural network (CNN) architecture that utilizes an attention mechanism. Afterwards, we propose a new framework for segmentation using the above single-ingredient classification model as the backbone. In this framework, two methods are involved in segmenting ingredients in the food images. We introduce five evaluation metrics (IoU, Dice, Purity, Entirety, Loss of GTs) to assess the performance of ingredient segmentation in terms of ingredient classification. Extensive experiments demonstrate the effectiveness of the proposed method, achieving an maximal mIoU of 0.65, mDice of 0.77, mPurity of 0.83, mEntirety of 0.80, and mLoGTs of 0.06 on the FoodSeg103 dataset. The results confirm that our CNN-based architecture achieves higher segmentation performance compared to ResNet18 and EfficientNet-B0 when used as the backbone for ingredient segmentation. We believe that our ingredient segmentation approach lays the foundation for subsequent ingredient recognition.

The paper proposed a modification of the GeoSER(D) model previously developed by us by detailing the age structure of the population, personal schedule on weekdays and working days, and individual health characteristics of the agents, this made it possible to build a more realistic model of the functioning of the city and its residents. The developed model made it possible to simulate the spread of 3 types of the strain of the COVID-19 virus, and to analyze the adequacy of this model in the case of unhindered spread of the virus among city residents. The paper showed that SARS COV 2 spreads mainly from contacts in workplaces and transport, and schoolchildren and preschool children are the consequence, not the initiator of the epidemic. Fluctuations in the dynamics of various indicators of the spread of SARS COV 2 associated with the difference in the daily schedule on weekdays and weekends. It has been shown that people's daily schedules strongly influence the spread of SARS COV 2. For the more contagious "rapid" strains of SARS COV 2 (omicron), immunocompetent people become a significant source of infection. For the less contagious "slow strains" (alpha) of SARS COV 2, the most active source of infection is immunocompromised individuals (pregnant women). The more contagious – "fast" strain of the SARS COV 2 virus (omicron) spreads faster in public transport. For less contagious – "slow" strains of the virus (alpha), the greatest infection occurs due to work and educational contacts.

At the highest level of endurance sports, the differences in finishing times are small, so equipment is constantly being constantly improved to enhance the athletes' performance. For instance, one dominant resistive force in connection with cross-country skiing is the friction between the skis and snow and since the 1930s, research designed to understand and reduce this friction has been ongoing. The mechanisms involved in ski-snow friction include compaction, micro-ploughing, adhesion, viscosity, and water-bridging. Of these, adhesive and viscous friction have been most studied, while much less is presently known about compaction, micro-ploughing, and water-bridging. At the macro-scale, the ski-camber profile plays a key role in determining whether, with respect to friction, a particular cross-country ski is suitable for use under a given set of conditions. Through its influence on where ski-snow contact occurs, this ski-camber profile has a profound impact on adhesive and viscous friction, micro-ploughing, the formation of water bridges, and the rate of compaction. Different contact zones with different apparent areas of contact and pressure have been found to be most suitable for different conditions. In addition, the micro-scale texture of the ski base is also an important determinant of ski-snow friction. Topographical measurements of this texture can be achieved with white-light interferometer and recent characterisation has focused on the mechanical properties of contact. In numerous tribological studies the interactions between features at different scales are modelled. In most tribological systems, features on several scales influence friction and ski-snow contact is certainly no exception. Accordingly, the current investigation was designed to evaluate the multi-scale properties of different combinations of two skis with two different base textures. The real area of contact and the average interfacial separation and total average reciprocal interfacial separation between the ski and snow were taken into consideration. We found that different macro- and micro-scale properties of the ski favour different mechanisms of friction. Both the profile of the ski camber and texture of the base play decisive roles in determining viscous friction. At the same time, the texture of the ski base exerts a greater impact on the average real contact pressure, real contact area and minimal average interfacial separation between the ski and snow than does the ski-camber profile.

To predict the remaining useful life (RUL) of proton exchange membrane fuel cell (PEMFC) in advance, a prediction method based on the voltage recovery model and Bayesian optimization of a multi-kernel relevance vector machine (MK-RVM) is proposed in this paper. First, the empirical mode decomposition (EMD) method was used to preprocess the data, and then the MK-RVM was used to train the model. Then, the Bayesian optimization algorithm was used to optimize the weight coefficient of the kernel function to complete the parameter update of the prediction model, and the voltage recovery model was added to the prediction model to realize the rapid and accurate prediction of the RUL of PEMFC. Finally, the method proposed in this paper was applied to the open data set of PEMFC provided by FCLAB, and the prediction accuracy of the RUL of PEMFC was obtained by 95.35%, which showed that the method had good gen-eralization ability and verified the accuracy of the prediction for the RUL of PEMFC.

Eco-labels are an instrument for enabling informed food choices and supporting a demand-sided change towards a more and urgently needed sustainable food system. Lately, novel eco-labels that depict a product’s environmental life-cycle assessment on a multi-level scale are being tested across Europe’s retailers. This study elicits consumers preferences and willingness to pay (WTP) for a multi-level eco-label. A Discrete Choice Experiment was conducted in Austria. Individual partworth utilities were estimated by means of Hierarchical Bayes. Results show higher WTP for a positive evaluated multi-level label, revealing consumers’ perceived benefits of colorful multi-level labels over binary black-and-white designs. Even a negative evaluated multi-level label showed higher WTP compared to no label, pointing towards limited effectiveness of eco-labels. Respondents’ preferences for eco-labels were independent from their subjective eco-label knowledge, health consciousness, and environmental concern. The attribute “protein source” was most important, and preferences for animal-based protein source (beef) was strongly correlated with consumers’ meat attachment, implying that a shift towards more sustainable protein sources is challenging and sustainability labels have only a small impact on the meat product choice of average consumers.

Electrospinning is a simple versatile method to generate nanofibres. Remarkable progress has been made in the development of electrospinning process. The production of nanofibers is affected by many parameters, which influence the final material properties. Electrospun fibers have a wide range of applications such as energy storage and biomedical scaffolds. Polyacrylonitrile (PAN) has been widely used in the production of carbon nanofibers. PAN has received increasing interest in recent years, due to its excellent characteristics, such as spinnability, biocompatibility, and commercial viability, opening new applications in the biotechnological field. This paper provides an overview of the electrospinning process, its main parameters, and operation modes that affect nanofibers fabrication. A review of their biological applications is proposed. A focus is made on PAN fibers formation, functionalization, and application as scaffolds to allow cell growth. Overall, nanofibre scaffolds, made of stabilized PAN, appear as a powerful tool in medical applications needing controlled cell culture.

In response to reducing the energy cost of unmanned surface vehicles (USVs) while overcoming the low accuracy problem in surface target detection, a lightweight detection algorithm with multi-scale feature fusion is proposed. Based on the popular one-stage lightweight Yolov7-tiny target detection model, a lightweight extraction module is designed first by introducing the multiscale residual module to reduce the number of parameters and computational complexity while improving accuracy. The Mish and SiLU activation functions are used to enhance network feature extraction. Second, the path aggregation network employs coordinate convolution to strengthen spatial information perception. Finally, the dynamic head, which is based on the at-tention mechanism, improves the representation ability of object detection heads without any computational overhead. According to the experimental findings, the proposed model has 22.1% fewer parameters than the original model, 15% fewer GFLOPs, a 6.2% improvement in [email protected], a 4.3% rise in [email protected]:0.95, and it satisfies the real-time criteria. According to the research, the suggested lightweight water surface detection approach includes a lighter model, a simpler computational architecture, more accuracy, and a wide range of generalizability. It performs bet-ter in a variety of difficult water surface circumstances.

This work analyzes a new indoor laboratory data set looking at early fire indicators in controlled and realistic experiments representing different incipient fire scenarios. The experiments were performed within the confines of an indoor laboratory setting using multiple distributed sensor nodes on different room positions. Each sensor node collected data of particulate matter (PM), volatile organic compounds (VOC), CO, CO2, H2, UV, air temperature and humidity in terms of a multivariate time series. These data hold immense value for researchers within the machine learning and data science communities who are keen on exploring innovative advanced statistical and machine learning techniques. They serve as a valuable resource for the development of early fire detection systems. The analysis of the collected data was carried out in dependence of the manhattan distance between the fire source and the sensor node. We found that especially larger particles (> 0.5 μm) and VOCs show a significant dependency with respect to the intensity as a function of the manhattan distance to the source. Moreover, we observed differences in the propagation behavior of VOCs, PM, and CO, which are particularly relevant in incipient fire scenarios due to the presence of strand popagation effects.

We found an important fact that the beam footprint line of Ping will intersect with the real water depth when the initial incidence angle is about 45°, and sound velocity error hardly has an effect on it. This is contrary to our previous experience that the soundings of the central beam of multi-beam bathymetric system (MBS) is the most accurate. Firstly, the influence of sound velocity errors on central beam and seafloor topography distortion was analyzed. Secondly, the process of proving this fact was given, and the topography correction method was proposed by compensating the sound velocity profile area (SVP area). Finally, we showed in the first simulation of four type errors in SVPs that this fact is verified. The topography correction method used in the second simulation to correct the topography distortion of the first simulation is also verified.

The method propose in this study for stock market multi-objective mathematical model was linear programming using simplex algorithms to optimize the portfolio in the Nigerian Stock Market. The study selected five banks from the list of operators in the market and data were gathered from the banks to have individual market performances over a period of 5years. The data collected contains: Geometric Mean of Monthly Capital Gain Yields and Annual Capital Gain Yields from which Dividend Yields (%) were deducted to arrive Actual rate of return for the banks and the expected rate of return. Furthermore, the risk of semi-absolute deviation below the expected return is reduced. The data was analysed using Python programming because of some clauses in the data gathered. At first, the data assumes integer (-or +) and random in nature. As such, Python programming is one of the software suitable for such solution since the barrier for additivity is broken. Based on the analysis, the study therefore conclude that the potential investor(s) should invest in 13 units of investment x(GTbank Plc), 3 units of First Bank Plc`s Investment (y), 450 units of Zenith bank`s investment (z), and 8 units of Wema bank`s investment (m), and no units of investment of (n) Access bank. These investment quantities will result in the Optimal profit of p= 12797.902 billion naira.

: Polymer single screw extrusion is a major industrial processing technique used to obtain plastics products. To assure high outputs, tight dimensional tolerances, and excellent product performance, extruder screws may show different design characteristics. Barrier screws, which contain a second flight in the compression zone, have become quite popular as they promote and stabilize polymer melting. Therefore, it is important to design efficiently extruder screws and decide whether a conventional screw will do the job efficiently, or a barrier-screw should be considered instead. This work uses multi-objective evolutionary algorithms to design conventional and barrier screws (Maillefer screws will be studied) with optimized geometry. Processing of two polymers, Low Density Polyethylene and Polypropylene, is analyzed. A methodology based on the use of Artificial Intelligence (AI) techniques, namely data mining, decision making and evolutionary algorithms, is presented and utilized to obtain results with practical significance, based on relevant performance measures (objectives) used in the optimization. For the various case studies selected, Maillefer screws were generally advantageous for processing LDPE, while for PP the use of both types of screws would be feasible.