The fluid seepage in local-saturated zone of subgrade promotes the migration of fine particles in the filler, resulting in the change of pore structure and morphology of the filler and the deformation of solid skeleton, which affects the fluid seepage characteristics. Repeatedly, the muddy interlayer, mud pumping and other diseases are finally formed. Based on the theory of two-phase seepage, the theory of porous media seepage, and the principle of effective stress in porous media, a two-phase fluid-solid coupling mathematical model in local-saturated zone of subgrade considering the effect of fine particles migration is established. The mathematical model is numerically calculated with the software COMSOL Multiphysics○R, the two-phase seepage characteristics and the deformation characteristics of the solid skeleton in local-saturated zone of the subgrade are studied. The research results show that due to the continuous erosion and migration of fine particles in local-saturated zone of the subgrade, the volume fraction of fine particles first increases then decreases and finally becomes stable with the increase of time. And the volume fraction of fine particles for the upper part of the subgrade is larger than that for the lower part of the subgrade. The porosity, the velocity of fluid, the velocity of fine particles, and the permeability show a trend of increasing first and then stabilizing with time; the pore water pressure has no significant changes with time. The vertical displacement increase first and then decrease slightly with the increase of time, and finally tend to be stable. For a filler with a larger initial volume fraction of fine particles, the maximum value of the volume fraction of fine particles caused by fluid seepage is larger, and the time required to reach the maximum value is shorter. It can be concluded that in actual engineering, the volume fraction of fine particles in the subgrade filler should be minimized on the premise that the filler gradation meets the requirements of the specification.

It is meaningful to monitor and identify the concrete cracks as they will seriously reduce the fatigue life of pavement. In this paper a new method based on distributed long-gauge optic fiber sensing is proposed to implement the crack identification. Firstly, the damage indicator, namely strain curve envelope area ratio (SCEAR), is proposed and calculated with the measured strain in time series when the plane goes across the pavement where the sensors are installed. Then the indicators with different sensors are normalization by the value of the indicator from one referenced sensor where damage normally will not happen. If the crack happens within the sensing gauge of the sensor, the value of damage indicator SCEAR from the sensor will increase. Therefore, the crack will be identified with the change of the damage indicator. The effect of the proposed method is first verified by some simulations of prefabricated pavement as the cracks can be accurately identified by the proposed method. Moreover, the influence from the aircraft, such as taxiing position, aircraft load and aircraft type, is not obvious enough to mislead the identification results. Lastly the static loading tests were implemented with one small-scale model of prefabricated concrete pavement in the lab. From the experimental results the prefabricated cracks inside the pavement slab can be identified accurately with the proposes method as the parameter SCEAR is increased by about 100% at the crack position, while it is only changed by about 3% at the undamaged position.

Introduction: Thyroid nodules are extremely common and require complex management to prevent unnecessary surgical intervention and ensure that no malignant disease is overlooked. Several diagnostic tools and scoring systems are available to evaluate the Risk of Malignancy (ROM). The goal is to assess variables that can aid and support the clinical recommendations suggested by the updated Bethesda System for Reporting Thyroid Cytopathology (TBSRTC), such as the ultrasonographic features of thyroid nodules, particularly for indeterminate categories III (atypia of undetermined significance) and IV (follicular neoplasm). Methods: We retrospectively analysed the correlation of the demographic and ultrasonographic characteristics of thyroid nodules with the cytopathological and histopathological diagnoses of TBSRTC categories III (atypia of undetermined significance), IV (follicular neoplasm), V (suspicious for malignancy), and VI (malignant) in patients who underwent surgery in a single Portuguese centre over a 10-year period. Results: In total, 360 nodules were evaluated in 341 patients and 57% were histopathologically malignant or borderline. The majority were included in the TBSRTC indeterminate categories III and IV with an ROM of 44% and 43%, respectively. The ultrasonographic characteristics associated with a higher TBSRTC category and a greater ROM value were hypoechogenicity, presence of microcalcifications, irregular margins, and the presence of cervical adenopathy. When correlating with a malignant histology, only adenopathy and the presence of microcalcifications were observed to be statistically significant. Discussion: The indeterminate categories of the TBSRTC have been the most challenging ones to manage. The new TBSRTC (2023) guidelines as well as the ultrasonographic characteristics of a patient can be helpful in assessing the ROM and deciding on an appropriate course of treatment. Other resources, such as molecular tests, are also gaining a more important role in the clinical decision process and may become crucial in the future. Conclusion: The clinical management of thyroid nodules requires a careful analysis of clinical history and an evaluation of demographic details, the symptoms of the patient, comorbidities, personal and family history, ultrasonographic features, and the results of cytopathology, thyroid function, and molecular/genetic tests to provide the best care possible. Patients with thyroid nodules of an indeterminate character can obtain a definitive diagnosis through surgery. However, by employing a complete analysis of all relevant data, some patients may be suitable for active surveillance instead of a surgical intervention.

The amorphous Fe77Cu1Si13B9 ribbons were treated with pulsed laser interference heating (PLIH). It was confirmed here that the use of the laser heating process allowed for obtaining two-dimensional crystallised micro-areas, periodically distributed (at a distance of 17µm) on the surface of the amorphous ribbons. The correlation between structural changes (SEM, TEM, HRTEM) and the distribution of magnetic field lines of heated amorphous Fe77Cu1Si13B9 (FeCuSiB) ribbons is presented. Particular attention is paid to structure changes in micro-areas where, by controlling the laser interference heating process, partial crystallisation of amorphous alloys and the formation of clusters or single nanocrystallites (α-Fe(Si)) embedded in an amorphous matrix are given. The addition of copper to the FeSiB alloy promoted inhibition of grain growth. Electron holography of micro-areas confirmed shifts of the magnetic field lines in the areas of nanocrystallites, the presence of which in the structure caused magnetisation of the surrounding amorphous matrix.

Leaf mass per area (LMA) is a key structural parameter that reflects the functional traits of leaves and plays a vital role in simulating the material and energy cycle of plant ecosystems. In this study, vertical whorl-by-whorl sampling of LMA was conducted in a young Larix principis-rupprechtii plantation during the growing season at the Saihanba Forest Farm. The vertical and seasonal variations in LMA were analysed. Subsequently, a predictive model of LMA was constructed. The results revealed that the LMA varied significantly between different crown whorls and growing periods. In the vertical direction of the crown, the LMA decreased with increasing crown depth, but the range of LMA values from the tree top to the bottom was, on average, 30.4 g/m2, which was approximately 2.5 times greater in the fully expanded phase than in the early leaf-expanding phase. The LMA exhibited an allometric growth trend that increased during the leaf-expanding phase and then tended to stabilize. However, the range of LMA values throughout the growing period was, on average, 40.4 g/m2. Among the univariate models, the leaf dry matter content (LDMC) performed well (Ra2=0.45, RMSE=13.48 g/m2) in estimating the LMA. The correlation between LMA and LDMC significantly differed at different growth stages and at different vertical crown whorls. The dynamic predictive model of LMA constructed with the RDINC and DOY as independent variables was reliable in both the assessments (Ra2=0.68, RMSE=10.25 g/m2) and the validation (MAE=8.05 g/m2, FI=0.682). Dynamic simulations of crown LMA provide a basis for elucidating the mechanism of crown development and laying the foundation for the construction of an ecological process model..

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

Abstract: rainfall is the main driver of soil erosion. With the daily rainfall, riverine flow discharge and sediment load in the upper Lianjiang River watershed from 1990 to 2020, extreme rainfall events were defined by the 95th percentile method and minimum event interval time (MIT), change trends and mutations of yearly rainfall, riverine flow discharge and sediment load were identified using the Mann-Kendall test, then the optimum lag response time and antecedent rainfall were investigated with the multiple linear regression. The results showed that (1) the sediment changed significantly and abruptly in 1995 due to the expansion of the garden land. (2) Compared with ordinary rainfall, extreme rainfall events explained more variations of riverine flow and sediment with a higher degree, and had a more significant effect on the lag time of runoff and sediment. (3) Garden land expansion in extreme rainfall scenarios resulted in longer lag times for runoff and sediment and decreased demand for antecedent rainfall with more pre-event time. Therefore, taking the rainfall event as a breakthrough, analyzing the antecedent rainfall and the lag response of riverine flow discharge and sediment load is conducive to revealing the response mechanism of riverine flow discharge and sediment load and improving the simulation accuracy of riverine flow and sediment under extreme rainfall condition, thus help for the soil erosion control under extreme rainfall.

Conducted within the scope of geochemical exploration in Eastern Thailand, this study aims to detect geochemical anomalies and potential mineral deposits. The objective was to interpret intricate spatial dispersion patterns and concentration levels of deposit pathfinder elements, specifically arsenic (As), copper (Cu), and zinc (Zn), using a comprehensive array of stream sediment geochemistry data. Methodologies involved integrating multifractal properties and traditional statistics, facilitated by the GeoDAS and ArcGIS platforms as instrumental analytical tools. In total, 5,376 stream sediment samples were collected and evaluated, leading to the development of an in-depth geochemical map. The results indicated distinct geological units marked by substantially elevated average values of the aforementioned elements. Identification of geochemical anomalies was achieved through the spatial distribution method and the subsequent application of the Spectrum-Area (S-A) multifractal model. An intriguing link was found between high As concentrations and gold deposits in the area, suggesting As as a viable pathfinder element for gold mineralization. The anomaly maps, generated from the stream sediment data, spotlighted potential zones of interest, offering valuable guidance for future mineral exploration and geological inquiries. Nonetheless, it is vital to recognize that the increased values noted in these maps may be influenced by regional geological factors, emphasizing the necessity for a diverse set of analytical methods for accurate interpretation. The study's significance lies in its pioneering use of the S-A multifractal model in geochemical data analysis. This innovative approach has deepened our comprehension of geochemical dispersion patterns and improved the precision of mineral exploration.

The South-to-North Water Transfer Jiangsu Water Supply Area (JWSA) is a mega inter-basin water transfer area (water source) that provides water resources from JiangHuai, combines drainage and flooding management, and regulates nearby rivers and lakes. Analyzing the spatiotemporal soil moisture dynamics in the area will inform agricultural drought and flood disaster assessment and early warning studies. Therefore, we evaluated the quality of European Space Agency Climate Change Initiative Soil moisture (ESA CCI_SM) data in the South-North Water Transfer JWSA. Then, we used ensemble empirical modal decomposition, Mann-Kendall tests, and regression analysis to study the spatiotemporal variation in soil moisture for the past 29 years. The CCI _SM data showed a high correlation with local soil measurements at nine sites. We then analyzed the CCI_SM data from three pumping stations (the Gaogang, Hongze, and Liushan stations) in the South-North Water Transfer JWSA. These stations had similar periodic characteristics of soil moisture, with significant periodic fluctuations around 3.1 d. The overall soil moisture at the three typical pumping stations showed an increasing trend. We then investigated whether there were abrupt soil moisture changes at each station. The spatial distribution of soil moisture in the South-North Water Transfer JWSA was characterized by “dry north and wet south”, with higher soil moisture in winter, followed by autumn, and low soil moisture in spring and summer. Although the linear trend of soil moisture in the South-North Water Transfer JWSA varied in significance, the overall soil moisture in the JWSA has increased over the past 29 years. The areas with significantly enhanced soil moisture are mainly distributed in the Yangzhou and Huai'an areas in the southeastern part of the study area. The areas with significantly decreased soil moisture are small in size and mainly located in northern Xuzhou.

Free-space communication is a leading component in global communications. Its advantages relate to a broader signal spread, no wiring, and ease of engagement. Satellite communication services became recently attractive to mega-companies that foresee an excellent opportunity to connect disconnected remote regions, serve emerging machine-to-machine communication, Internet-of-things connectivity, and more. Satellite communication links suffer from arbitrary weather phenomena such as clouds, rain, snow, fog, and dust. In addition, when signals approach the ground station, it has to overcome buildings blocking the direct access to the ground station. Therefore, satellites commonly use redundant signal strength to ensure constant and continuous signal transmission, resulting in excess energy consumption, challenging the limited power capacity generated by solar energy or the fixed amount of fuel. This research proposes LTSM, an artificial recurrent neural network technology that provides a time-dependent prediction of the expected attenuation level due to rain and fog and the signal strength that remained after crossing physical obstacles surrounding the ground station. The satellite transmitter is calibrated accordingly. The satellite outgoing signal strength is based on the predicted signal strength to ensure it will remain strong enough for the ground station to process it. The instant calibration eliminates the excess use of energy resulting in energy savings.

Research investigating the neural substrates underpinning parental behaviour has recently gained momentum. Particularly, the hypothalamic medial preoptic area (MPOA) has been identified as a crucial region for parenting. The current study conducted a scientometric analysis of publications from 01 January 1972 to 19 January 2021 using CiteSpace software to determine trends in the scientific literature exploring the relationship between MPOA and parental behaviour. In total, 677 scientific papers were analysed, producing a network of 1509 nodes and 5498 links. Four major clusters were identified: "C-Fos Expression'', "Lactating Rat'', "Medial Preoptic Area Interaction'' and "Parental Behavior''. Their content suggests an initial trend in which the properties of the MPOA in response to parental behavior were studied, followed by a growing attention towards the presence of a brain network, including the reward circuits, regulating such behavior. Furthermore, while attention was initially directed uniquely to maternal behavior, it has recently been extended to the understanding of paternal behaviors as well. Finally, although the majority of the studies were conducted on rodents, recent publications broaden the implications of previous documents to human parental behavior, giving insight into the mechanisms underlying postpartum depression. Potential directions in future works were also discussed.

The paper proposes a human explainable artificial intelligence approach for mapping the status of environmental phenomena from multisource geo data. It is both knowledge and data driven: it exploits remote sensing expert’s knowledge to define the contributing factors from which partial evidence of the environmental status can be computed. Furthermore, it aggregates the partial evidences to compute a map of the environmental status by adapting to a region of interest through a learning mechanism exploiting Volunteered Geographic Information (VGI), both from in situ observations and photointerpretation. The approach is capable to capture the specificities of local context as well as to cope with the subjectivity and incompleteness of expert’s knowledge. The proposal is exemplified to map the status of standing water areas (i.e. water bodies and river, human driven or natural hazard flooding) by considering satellite data and geotagged observations. Results of the validation experiments were performed in three areas of Northern Italy, characterized by distinct ecosystems. Results of the proposed methodological framework showed better performances than traditional approaches based on single spectral indexes thresholding. The use of expert’s knowledge, possibly imprecise/uncertain and incomplete, the need of few ground truth data for learning, and finally the explainability of learned rules are the distinguishing characteristics of the proposal with respect to traditional machine learning methods.

The advantageous location, port clusters, strong economic strength, developed financial system, rational and orderly urban division of labor and modern industrial system of Guangdong-Hong Kong-Macao greater bay area provide sustainable driving force for innovation activities in this region. This paper selected the Gini-coefficient, first degree index and concentration index to measure the spatial pattern characteristics of innovation output in Guangdong-Hong Kong-Macao greater bay area. The results show that the innovation output presented a spatial pattern of center-periphery in the study region with Shenzhen and Guangzhou as the dual centers and engines of innovation and Dongguan and Foshan as the main innovative areas. Further empirical analysis of the impact of various factors on innovation output in the study region found that R&D expenditure, the number of R&D personnel, the level of economic development and industrial structure all have significant promoting effects on innovation output. Accordingly, this paper put forward countermeasures and suggestions to promote the innovative development of Guangdong-Hong Kong-Macao greater bay area and build a world-class scientific and technological innovation bay area.

Smart agriculture is a new way of farming that uses advanced technology. It makes a significant contribution to improving the efficiency and productivity of farming practices. Systems that use drones to monitor pests and spray pesticides greatly reduce the burden on farmers. In addition, remote sensing technology facilitates the monitoring of crop growth conditions and the early detection of diseases and pests. However, the high cost of equipment to communicate sensor data is preventing farmers from adopting sensing systems. As a result, many studies have been conducted to make the sensing system available at a low cost. Nevertheless, many farmers have not yet adopted them. Therefore, this paper proposes an agricultural sensor network system using drones and optical camera communication (OCC). The proposed system aims to achieve high-density farm sensing at low cost. The proposed system uses OCC as the communication method for sensor data. Low cost light sources such as LED panels can be used as transmitters. In addition, existing agricultural drones equipped with cameras can be used as receivers. We also propose a trajectory control algorithm for the receiving drone to efficiently collect the sensor data. The proposed system is suitable for deploying sensor networks in areas with underdeveloped infrastructure and radio silence. In this paper, we conducted a preliminary experiment at a leaf mustard farm in Kamitonda-cho, Wakayama to demonstrate the effectiveness of the proposed system using a Mavic 2 Pro drone, launched by DJI Co., Ltd.

In this study, it was analyzed that the characteristics of ammonia and their effects on secondary particulate matter (PM) formation by region in Korea during 2020. The NH3 concentration was high in GJ (11.4 ppb) neighboring agricultural area followed by DJ (9.0 ppb) and SE (8.6 ppb) locating in the urban area. On the other hand, BI (2.6 ppb) and JI (4.5 ppb), which are background regions, were lower than other area. Seasonally, ammonia was high in spring and summer, and it generally increased when human activities are active. Therefore, it is believed that ammonia in the atmosphere changes depending on not only local emissions but also temperature-dependent phase distribution characteristics. For SE and GJ, regions with relatively high ammonia concentrations, the effect of ammonia on secondary PM formation was conducted. In both regions, the ammonium-to-sulfate mole ratio tended to increase with an ammonia or PM2.5 concentration increasing. It can be assumed that PM2.5 concentration increases as nitrates are formed under the ammonia sufficient condition. The adjusted gas ratio is generally greater than 4, indicating that there is a lot of free ammonia. Thus, it is estimated that reduction of ammonia would not effective to restrain the nitrate formation.

This paper explores the critical role of the banking sector in facilitating the ecological transition through the integration of ESG (Environmental, Social, and Governance) factors. By analyzing the intersection of ESG considerations and access to credit globally, the study highlights how banks can catalyze sustainable investments while balancing financial risks. Using a systematic literature review and k-Means clustering analysis, we assess the global landscape of credit access, emphasizing the implications of ESG adoption on financial stability and economic growth. The findings suggest that while ESG integration presents challenges, it offers significant opportunities for banks to enhance their competitiveness and foster resilient financial systems. The paper concludes by proposing policy recommendations aimed at improving the incorporation of ESG factors within credit risk management and promoting sustainable finance.

(1) Background: São Paulo, Brazil, exhibits high mortality rates from pediatric solid tumors. This study analyzed the survival trends of patients aged 0-19 diagnosed with the state's five most prevalent solid tumors between 2000-2022. (2) Methods: An epidemiological, descriptive study utilized data from the Oncocentro Foundation of São Paulo, classified according to the International Classification of Childhood Cancer. The time between the first consultation and diagnosis, between diagnosis and treatment initiation, and patient survival were assessed using the Pe-to-Peto test. (3) Results: Analysis involved 11,067 cases: 53.5% male, with 89.6% diagnosed via microscopic confirmation. Tumor distribution comprised 34.3% central nervous system, 21.1% bone, 18.6% soft tissue, 14.2% germ cell, and 11.9% retinoblastomas. Main treatments included surgery with chemotherapy (26.5%), surgery alone (20.5%), and chemotherapy alone (15.6%). The average time between consultation and diagnosis was 22.94 ± 69.93 days, significant for treatments and recurrences, except for germ cell tumors (p=0.0178). The time between diagnosis and treatment was 25.46 ± 39.71 days, not significant for germ cell tumor treatments (p=0.0793). (4) Conclusions: Survival curves varied among neoplasm groups, with patients experiencing delays beyond recommended times, despite advanced healthcare services in the state.

The theory of limited numbers says that the number is not infinite, that is, the number is limited in parts or completely. To reach a conclusion about the limited number, one must understand the meaning of mathematics and varied spaces, therefore, one must understand that mathematics and spaces interact. Mathematics has the function of describing the world precisely, where numbers represent elements or facts that rationally belong to space, and spaces have different intensities of specific physical concepts in each space; therefore, there is no infinite element or fact due to differences in the intensities of specific physical concepts in spaces that do not allow for the fact or fact in all spaces.

Parkinson’s disease (PD) is the second most common degenerative disease which may cause blood pressure abnormalities due to autonomic dysfunction. Early morning rise of blood pressure which is called morning surge is found to be related with some cardiovascular diseases when it is exaggerated. We wanted to search the relation of Morning blood pressure surge (MBPS) and inflammation in PD. Method: Ambulatory blood pressure monitoring for 24 hours, fibrinogen to albumin ratio, hs-CRP are used in this retrospective study. Fifty idiopathic PD patients and 50 age and sex matched control cases were included. MBPS, it has been defined as the difference between morning BP (measured 2 hours after awakening) and the lowest night-time BP. Body mass index (BMI) is used as an independent variable. Results: Median value of MBPS for PD group (21,63) was significantly different from the control group values (18,63) (p

Green and low-carbon development has become an important embodiment of China's path to becoming a strong agricultural country. How to enable agricultural enterprises to better adopt green technologies and conduct production and operation with the concept of sustainable development has become a key link. This article utilizes a structural equation model (SEM) to analyze the role paths and mediating effects of organizational learning ability and policy orientation in agricultural enterprises' market orientation and willingness to adopt green technologies[ The definition of green technology in this paper refers to Guo Kesha, Tian Xiaoxiao. Green technology and green transformation of industrial development mode [J]. Tianjin Social Sciences, 2024 (02) :99-107, including green manufacturing (production) technology and green service technology.]. The results show that market orientation, organizational learning ability, and policy effectiveness have significant direct positive impacts on the willingness to adopt; market orientation has a significant positive impact on agricultural enterprises' organizational learning ability, organizational learning ability has a significant positive impact on policy orientation, and market orientation has a significant positive impact on policy effectiveness; the results of mediation analysis also indicate that learning ability has a significant mediating effect between market orientation and willingness to adopt, and policy effectiveness has a significant mediating effect between market orientation and willingness to adopt. Through difference analysis, it is believed that the mediating effects of the three paths are equally important, and organizational learning ability and policy effectiveness play a partial mediating role in agricultural enterprises' willingness to adopt green technologies. Based on this, policy suggestions are proposed to improve enterprises' own organizational learning ability, increase the promotion of policies related to green technologies, improve relevant policies for the application of green technologies, and increase research and development efforts for green technologies.

To reduce the redundant counting of TDC in high-speed applications and thus reduce power consumption, a TDC architecture is proposed to quantify the difference between two adjacent rows of pixel signals. This structure can remove the identical part between two rows of pixel signals by adjusting the start and stop signal of the TDC, which will reduce the number of flipping of D flip-flops in the TDC. In the 110nm CMOS process, simulation results show that this design achieves an effective number of bits (ENOB) of 4.72 bits and a Figure of Merit (FoM) of 104.7 fJ/step - 162.3 fJ/step with a power consumption ranging from 60 µW to 93 µW. Compared with traditional counting methods, the proposed TDC can reduce counting power consumption by 30%.

The benefits of cycling as a sustainable transportation mode are widely recognized. Cycling to work offers numerous advantages for individuals, employers, the environment, and society, ranging from improved physical health, wellbeing, and productivity to enhanced public health and reduced carbon emissions. Many governments around the world have implemented various policy measures, interventions, and initiatives to promote cycling. Some cities and towns have encouraged workplaces to provide bike-friendly amenities, such as secure bike parking/storage and shower and changing facility (referred to as end-of-trip facilities), to accommodate cyclists and motivate more employees to embrace sustainable transportation options. However, the presence or absence of such amenities has been found to both positively influence cycling behavior or deter some individuals from cycling to work. Despite the desirability of these amenities, the number of office buildings equipped with bike storage and shower/changing facility remains small, and their economic value is not well understood. In this paper, we aim to investigate whether the presence of cycling-supportive facilities could add value to office buildings. Specifically, we conduct a study using data from office buildings across England as of the end of 2021. We employ hedonic techniques to examine whether office buildings with bike storage and/or shower facility command a rent premium and whether the existence of a rent premium for bike storage and/or shower facility vary by location and across regions in England, independently from any premium associated with BREEM certification. We find that the buildings with bike storage and shower facility secure rent premiums respectively. The level of rent premiums varies with location and regions. The variations of premium are driven by the shortage of the supply of these facilities.

The aim of the research was to determine the most productive tree cutting methods and the factors influencing them in flat and sloping terrain in tree plantations in Brazil. The study utilized drone-captured video material from eucalyptus and pine plantations harvesting operations. In both terrains, two cutting methods were compared, differing in the felling to the side method used: either at the edge of the harvesting front or inside. In addition, on flat terrain, the efficiency of forward felling was studied in relation to the aforementioned methods. In slope terrain, the machines were also equipped with a winch assistance system. Statistical tests were used to determine the most productive cutting methods by analyzing differences in productivity. With an average tree size of 0.3 m3, cutting productivity was 45 m3/E0h in pine cuttings and 55 m3/E0h in eucalyptus cuttings. The average cutting productivity on flat terrain was about 11 m3/E0h higher than on sloping terrain, mainly due to the time spent attaching the winch assistance system, which was a necessary phase of the work in sloping terrain. The research results suggest that it would be the most productive to use sideways felling inside the harvesting front method. However, the need for further research is evident if we want to precisely identify the harvesting conditions and work phases in the tree cutting cycle affecting the differences in the productivity of the harvesting chain in tree plantations.

The paper proposes a methodological way to compensate the imbalance between energy generation and consumption using the battery block of electric vehicles as energy reservoir through the well-known Vehicle to Grid system (V2G). The method is based on a simulation process developed by the authors that take into consideration the daily fluctuations of energy consumption as well as the power level generated by an energy source, either conventional, renewable or hybrid. The study shows that for very large electric vehicle fleet the system renders non-viable, since the remaining energy in the battery block to let the electric vehicle usable for running during daytime avoids to compensating for the energy grid imbalance, only allowing to cover a percentage of the energy imbalance, which the proposed methodology may optimize. The analysis of the proposed methodology also shows the viability of the system when being applied to a small fleet of electric vehicles, not only compensating for the energy imbalance but also preserving the required energy in the battery of the electric vehicle to make it run. The method allows predicting the optimum size of electric vehicle battery, which depends on the energy generation level, coverage factor of the energy imbalance and size of the electric vehicle fleet.

Commercial buildings situated in hot and humid tropical climates rely significantly on cooling systems to maintain optimal occupant comfort. A well-accurate day-ahead load profile prediction plays a pivotal role in planning the energy requirements of cooling systems. Despite the pressing need for effective day-ahead cooling load predictions, current methodologies have not fully harnessed the potential of advanced deep-learning techniques. This research paper aims to address this gap by investigating the application of innovative deep learning models in day-ahead hourly cooling load prediction for commercial buildings situated in tropical climates. A range of deep learning techniques, including Deep Neural Network, Convolutional Neural Networks, Recurrent Neural Networks, and Long Short-Term Memory networks are employed to enhance prediction accuracy. Furthermore, these individual deep learning techniques are synergistically integrated to create hybrid models, such as CNN-LSTM and Sequence-to-Sequence models. An extensive comparative analysis is conducted to identify the most effective hybrid model. Sequence-to-sequence model provided better performance compared to the other single and hybrid models. Experiments are conducted to choose the time horizons from the past that can serve as input to the models. Further, the influence of various categories of input parameters on prediction performance has been assessed. Historical cooling load, calendar features and outdoor weather parameters are found in decreasing order of influence on prediction accuracy. This research focuses on buildings located in Singapore and presents a comprehensive case study to validate the proposed models and methodologies.

Pedestrians, bicyclists, scooterists are Vulnerable Road Users (VRU) in traffic accidents. The number of fatalities and injuries in traffic accidents involving vulnerable road users has been steadily increasing in the last two decades in the U.S. even though road vehicles now have perception sensors like camera to detect risk and issue collision warnings or apply emergency braking. Perception sensors like camera are highly affected by lighting and weather conditions. Camera, radar and lidar cannot detect vulnerable road users in partially occluded and occluded situations. This paper proposes the use of Vehicle-to-VRU communication to inform nearby vehicles of VRUs having trajectories with potential collision risk. An Android smartphone app with low energy Bluetooth (BLE) advertising is developed and used for this communication. The same app is also used to collect motion data of VRUs for training. VRU motion data is smoothed using a Kalman filter and an LSTM neural network is used for future motion prediction. This information is used in an algorithm comparing Time-To-collision-Zone (TTZ) for the vehicle and VRU and issue a driver warning with different severity levels. The warning severity level is based on analysis of real data from a smart intersection for close vehicle and VRU interactions. The resulting driver warning system is demonstrated using proof-of-concept experiments. The method can easily be extended to a VRU collision mitigation system.

A significant amount of data is available for bench-scale fire assessments. However, there is little surrounding large-scale tests and even less so for bench-to-large scale comparisons. Large-scale tests require more material, time and preparation, making them more expensive than bench-scale assessments. However, large-scale testing is an essential component to bench-scale fire testing. The bench-scale tests must be representative of both large-scale and real fire behaviour to provide an insight into how a material or product will behave in the event of a fire during its end use application. The few existing studies reviewed in this study show more guidance and data is needed, especially on a large-scale. Unfortunately, the data that is presented is done so in an inconsistent manner using various means of presentation, statistical analysis, and modelling that doesn’t show clear comparisons between bench and large scale. Currently, no bench-scale method shows good agreement with large-scale fire behaviour. Overall, there is a need for more large-scale testing and data for direct comparisons to be made.

Background and Objectives: The severity of acute pancreatitis (AP) is graded as mild (MAP), moderately severe (MSAP), and severe (SAP) according to the revised Atlanta Classification. Determining the severity of AP is the main goal in the early time of AP. The aim of this study was to compare laboratory parameters or indices including neutrophil-to-lymphocyte ratio (NLR), platelet-to-lymphocyte ratio (PLR) and neutrophil-creatinine index (NCI) at admission for predicting severity of AP. Materials and Methods: In this retrospective study, the data from patients who admitted with diagnosis of AP between January 2018 and December 2021 were collected. Laboratory parameters and indices including NLR, PLR and NCI were compared in the discrimination of AP severity groups. Results: A total of 421 patients [MAP group (n=213), MSAP group (n=158) and SAP group (n=50)] were included. WBC count, neutrophil count, hematocrit, CRP, BUN, creatinine, NLR and NCI were significant parameters to discriminate AP subgroups. The AUROC analysis for discriminating MSAP from MAP showed that WBC (AUC: 0.723, 95% CI: 0.674-0.768, p<0.001), hematocrit (AUC: 0.566, 95% CI: 0.514-0.607, p=0.032), NLR (AUC: 0.649, 95% CI: 0.598-0.698, p< 0.001) and NCI (AUC: 0.749, 95% CI: 0.701-0.792, p<0.001) were statistically significant parameters. Similarly, AUCs to discriminate SAP from MSAP were (AUC: 0.649, 95% CI: 0.579-0.713, p < 0.001) for WBC, (AUC: 0.703, 95% CI: 0.621-0.785, p< 0.001) for BUN, (AUC: 0.602, 95% CI: 0.532-0.669, p=0.029) for CRP and (AUC: 0.742, 95% CI: 0.676-0.800, p<0.001) for NCI. Logistic regression analyses indicated that NCI was the only parameter to discriminate MSAP form MAP (OR: 1.119, 95% CI: 1.015-1.235, p=0.023) and SAP from MSAP (OR: 1.113, 95% CI: 1.042-1.888, p = 0.001). Conclusions: The present study enabled the identification of neutrophil-creatinine index as a new prognostic tool for the assessment AP severity at hospital admission.

The current study primarily aimed to simulate detonation initiation via turbulent jet flame acceleration in partial-premixed H2-air mixtures. Different vertical concentration gradients were generated by varying the duration of hydrogen injection (referred to as diffusion time) within an enclosed channel filled with air. H2-air mixtures with average hydrogen concentrations of 22.5% (lean mixture) and 30% (near stoichiometric mixture) were investigated at diffusion times of 3, 5, and 60 seconds. Numerical results show that the vertical concentration gradient has a major influence on the early-stage of flame acceleration (FA). In the stratified lean mixture, detonation began in all the diffusion times, and comparing the flame-speed graphs showed that a decrease in the diffusion time and an increase in the mixture inhomogeneity speeded up the flame propagation and the jet flame to detonation transition occurrence in the channel. In the stratified H2-air mixture with an average hydrogen concentration of 30%, transition from a turbulent jet flame to detonation occurred in all the cases, and the mixture inhomogeneity weakened the FA and delayed the detonation initiation.

Liver transplantation is currently the only curative therapy for patients with liver cirrhosis. Not all patients in the natural course of the disease will undergo transplantation, but the majority of them will experience portal hypertension and its complications. In addition to medical and endoscopic therapy, a key role in managing these complications is played by the placement of a transjugular intrahepatic portosystemic shunt (TIPS). Some indications for TIPS placement are well-established and they are expanding and broadening over time. This review aims to describe the role of TIPS in managing patients with liver cirrhosis, considering them as potential candidates for liver transplantation. As far as is known TIPS placement seems not to affect the surgical aspects of liver transplantation, in terms of intra operative bleeding rates, postoperative complications or length of stay in the Intensive Care Unit. However, the placement of a TIPS “towards transplant" can offer advantages in terms of enhancing the patient's clinical condition at the time of transplantation and improving patient survival. Additionally, the TIPS procedure can help preserve the technical feasibility of the transplant itself. In this context, indications for TIPS placement may be expanded and considered at an earlier stage. TIPS insertion can also lead to serious adverse events and there are no evidence-based recommendations on this topic to date. For these reasons further studies are needed to make reliable recommendations for TIPS in the pre-transplant setting.

Molnupiravir, a prodrug known for its broad antiviral activity, demonstrated efficacy in animal models of Covid-19, prompting clinical trials where initial results indicated a significant effect against the disease. However, subsequent clinical studies did not confirm these findings, leading to the rejection of molnupiravir for permanent market authorization in many countries. This report critically assessed 19 studies published in 17 reports that investigated the efficacy of molnupiravir in animal models of Covid-19 with the purpose of determining how well the design of these models informed human studies. We found that the administered doses of molnupiravir in most studies involving animal Covid-19 models were disproportionately higher than the dose rec-ommended for human use. Specifically, when adjusted for body surface area, half of the doses of molnupiravir used in the animal studies were more than twice as high as the human dose. Addi-tionally, the drug was frequently given prophylactically or shortly after SARS-CoV-2 inoculation in these models, in contrast to clinical trials where such timing is not consistently achieved. Furthermore, the recommended five-day treatment duration for humans was exceeded in several animal studies. Collectively, we suggest that these design elements in the reported animal studies contributed to a bias favoring molnupiravir, and thus inflated expectations for its efficacy against Covid-19. Addressing these elements may offer avenues to enhance the clinical efficacy of mol-nupiravir for treatment of Covid-19 that include dose increment, early treatment, and admin-istration by inhalation along with use of molnupiravir in antiviral combination therapy.

This paper introduces an advanced method that integrates contingent valuation and machine learning (CVML) to estimate residents’ demand for reducing or mitigating environmental pollutions and climate change. To be precise, CVML is an innovative hybrid machine-learning model, and it can leverage a limited amount of survey data for prediction and data enrichment purposes. The model comprises of two interconnected modules: Module I, an unsupervised learning algorithm, and Module II, a supervised learning algorithm. Module I is responsible for grouping the data into groups based on common characteristics, thereby grouping the corresponding dependent variable, whereas Module II is in charge of demonstrating the ability to predict and the capacity to appropriately assign new samples to their respective category based on input attributes. Take a survey on the topic of air pollution in Hanoi in 2019 as an example, we found that CVML can predict households’ willingness– to– pay for polluted air mitigation at a high degree of accuracy (i.e., 98%). We found that CVML can help users reduce costs or save resources because it makes use of secondary data that is available on many open data sources. These findings suggest that CVML is a sound and practical method that could be widely applied in a wide range of fields, particularly environmental economics and sustainability science. In practice, CVML could be used to support decision-makers in improving the financial resources to maintain and/or further support many environmental programs in years to come.

Environmental concerns, among other causes, are leading to meat replacement in the diet by healthy, nutritious and tasty foods. Alternative protein sources of plant origin can be an alternative to meat, but their low biological value proteins can be a problem. Novel foods, such as insect meals, can meet currently consumer demands. Therefore, this research has developed innovative prototypes of analogue burgers with animal and vegetable proteins. Concerned about health and allergies, a prototype incorporating soya to satisfy coeliacs was developed. An iterative and heuristic process was carried out to test the product development feasibility. The main raw materials used were insect flour (Tenebrio molitor), seitan and soya. In addition, oat and sodium alginate were used as binders. Shelf-life of the new product was evaluated by physicochemical (pH, aw, moisture, colour, acidity and peroxide index) and sensory analysis (quantitative analysis -QDA-). The production of the burger analogues was feasible. Product characterisation showed significant differences (p < 0.05) among samples for organoleptic properties, highlighting texture changes. Using a multivariate model, it was established “The best before date” at 7 days for all developed prototypes, conditioned by microbial growth. Finally, the spoilage model indicated an important contribution to bacterial growth with a notable modification in the pastiness and hardness of the burger analogues developed.

Waste-to-Hydrogen (Wahh) is a process of converting waste into hydrogen gas through various methods such as thermal conversion, biological conversion, and chemical conversion. This process not only helps in managing waste but also provides a clean source of energy as hydrogen is a renewable energy source that produces zero greenhouse gas emissions during combustion. Wahh has the potential to provide a sustainable solution for energy generation and waste management in the current scenario of globally increasing energy demands. This study aims to examine the properties and energy efficiencies of various renewable fuels including fuelwood, biogas, biomethane, and biohydrogen with a specific focus on differentiating the characteristics of biohydrogen. The paper explores the emerging concepts of waste-to-hydrogen microgrids, biohydrogen refineries, biohydrogen prosumer networks, and a biohydrogen circular economy, as well as Public-Private-People Partnerships (4Ps) and the hydrogen-centric renewable energy revolution, which are taking shape in industrialized countries. The study presents a comprehensive feasibility analysis of these concepts in the context of Nepal. The results of this research will provide valuable insights into the potential for adopting these innovative technologies in Nepal and will contribute to the development of a sustainable and efficient energy system.

Within this paper, a machine learning algorithm is used to investigate the importance of certain setpoints and parameters in the filtration processes of a large-scale water treatment facility. Previously, a model for the filtration process based on Run-to-Run Control was proposed and tested against sample data from the treatment plant, but it was quickly found that such a model was incompatible for successfully computing setpoints of operation which minimize the energy cost of running the filtration systems. The machine learning model described herein is an attempt to elucidate the importance of the available data on the filtration systems and to identify the most important variables that influence the filtration run time.

This research aims to contribute to the growing body of knowledge of Collaborative Consumption (CC) by exploring the motivations that influence the use of Peer-to-Peer (P2P) accommodation platforms from the demand side. There has been a significant increase in interest in sustainable choices regarding P2P accommodation in recent years. To address this gap and contribute to the collaborative consumption and P2P accommodation theory a quantitative study was conducted through a survey yielding 235 responses from both users and non-users of P2P platforms. The findings of this study suggest that P2P accommodation platform usage is influenced by multiple motivations, including sustainability, belonging, economic benefits, and convenience. Interestingly, the study also found that individuals with higher levels of academic qualifications are more likely to adopt this mode of consumption. Moreover, the study is the first of its kind to quantitatively address this topic and, therefore, contributes significantly to the field of collaborative consumption and P2P accommodation theory. By understanding the motivations of P2P platform users, policymakers and practitioners can develop targeted strategies to promote sustainable choices in this sector. Overall, this study provides a useful framework for future research on collaborative consumption and sustainable P2P accommodation.

The combination of non-steroidal anti-inflammatory drugs (NSAIDs) with non-opioid analgesics is common in clinical practice for the treatment of acute pain conditions like post-operative and post-traumatic pain. Besides that, and despite the very satisfactory results achieved by oral analgesics, parenteral analgesia is a key tool in the treatment of painful conditions when the enteral routes are not convenient. The parenteral ready-to-use fixed-dose combinations of NSAIDs with non-opioid analgesics like paracetamol or metamizole could play a central role in the treatment of painful conditions since they are able to gather into only one formulation the advantages of multimodal and parenteral analgesia. Surprisingly, only very recently a parenteral ready-to-use fixed-dose combination of Ibuprofen/Paracetamol was launched to the market. This review aims to review the current availability of NSAID-based Parenteral Fixed-dose combinations with paracetamol and metamizole in the European and American markets, and how the combination of such drugs could play a central role in a multimodal analgesia strategy. Also, it is explored how the parenteral formulations of NSAIDs, paracetamol, and metamizole could serve as starting elements for the development of new parenteral ready-to-use fixed-dose combinations. With this review, we concluded that, despite the well-recognized utility of combining NSAIDs with non-opioid analgesics, there are in the literature several randomized clinical trial studies unable to demonstrate clear advantages concerning their efficacy and safety. In the future, it is deemed necessary to perform clinical trials specifically designed to assess the efficacy and safety of these fixed-dose formulations to generate solid evidence of their clinical advantages.

In this paper, inspired by quantum field theory, or more specifically QED, we propose a dynamical model for relativity. By adopting the approach provided by this dynamical model, we provide a dynamical explanation for relativistic phenomena such as length contraction, time dilation and clock desynchronization. The result of the dynamical approach for clock desynchronization is especially interesting. Our dynamical approach exhausts the freedom for different clock synchronizations on frames accelerated from an initial reference frame, which is allowed by Einstein’s principle approach. Furthermore, our dynamical approach arrives at the interesting conclusion that Einstein’s equivalence principle and gravitational redshift are necessary to explain special relativistic clock desynchronization. This result shows that special relativity by itself is an incomplete theory. If our dynamical model assumptions are assumed to be valid at a fundamental level, it implies some modifications to quantum field theory and general relativity via the equivalence principle. These modifications have been discussed.

The manuscript presents a unified methodology for the engineering design of resonant inverters used for power sources to power various technologies based on induction heating. The methodology is compiled using the generalized consideration of electromagnetic processes in a series RLC circuit and the quasi-boundary method for the analysis of resonant inverters with and without reverse diodes operating in soft and hard commutation modes. On this basis, the transmission functions of the inverters are derived, and the matching between the parameters of the inverter and the load through complicated output circuits is also considered. The basic ratios for determining the circuit elements and their current and voltage loading are presented. The methodologies are verified using several computational examples, simulations and measurements from induction heating devices. The simplified design approach presented is useful for its application in power electronics training and also in the design of various devices using the principle of induction heating. Another important result is the achievement of formalization and algorithmization of the design process, which is a consequence of the application of a unified approach both in the analysis and in the design of a whole class of power electronic devices.

An out-of-hospital cardiac arrest (OHCA) is one of the leading causes of death in the world. The survival rate can be influenced by the Chain of Survival. The school is the institution that has the opportunity to promote the education of citizens in Basic Life Support (BLS), increasing the number of trained bystanders. This study aimed to identify the theoretical and practical knowledge and self-reported skills in BLS, in order to characterise the motivation to intervene in an emergency situation. A quantitative, descriptive, cross-sectional, and analytical study of the survey type was developed with a sample of 1215 students enrolled in 10th grade of secondary education in 2019-2020 in Portugal. The results point to a fragile appropriation of theoretical and practical knowledge in the field of BLS. Self-declared competences tend to rank below the theoretical knowledge manifested. Motivation to intervene is high: students are sensitive to the topic, willing to learn and highlight the importance and social relevance of the topic. We conclude that students do not feel nor are able to intervene in an OHCA episode. It seems necessary to develop didactic proposals that align the teaching of BLS with the Essential Learning at the end of compulsory education in Portugal.

Human and animal waste, including waste products originating from human or animal digestive systems such as urine, feces, and animal manure, have constituted a nuisance to the environment. Inappropriate disposal and poor sanitation of human and animal waste often cause negative impacts on human health through contamination of the terrestrial environment, soil, and water bodies. Therefore, it is necessary to convert these wastes into useful resources to mitigate their adverse environmental effect. The present study provides an overview and research progress of different thermochemical and biological conversion pathways for the transformation of human- and animal-derived waste into valuable resources. The physicochemical properties of human and animal waste are meticulously discussed as well as nutrient recovery strategies. In addition, a bibliometric analysis is provided to identify the trends in research and knowledge gaps. The results reveal that the U.S.A, China and England are the dominant countries in the research areas related to resource recovery from human or animal waste. In addition, researchers from the University of Illinois, the University of California Davis, the Chinese Academy of Science and Zhejiang University are front runners in research related to these areas. Future research should be centred on developing technologies for the on-site recovery of resources, exploring integrated resource recovery pathways, and exploring different safe waste processing methods.

The aim of this study was to estimate the association between fear of COVID-19 and risk perception with preventive behavior in health professionals from three Latin American countries. An analytical cross-sectional study was conducted. Health professionals with on-site care in Colombia, Ecuador, Guatemala, and Peru were surveyed. Information was collected through an online self-report questionnaire. The main variables were preventive behavior as the dependent variable and fear of COVID-19 and risk perception as independent variables. Linear regression was used, and Beta coefficients and p-values were calculated. 435 health professionals were included, the majority were aged 42 years or older (45.29%, 95%CI: 40.65%-50.01%) and female (67.82%, 95%CI: 63.27%-72.05%). It was shown that the greater the fear of COVID-19, the greater the preventive behavior of COVID-19 infection (B=2.21, p=0.002 for total behavior; B=1.12, p=0.037 for additional protection at work; B=1.11, p<0.010 for hand washing). The risk perception of COVID-19 infection had a slight direct relationship with preventive behaviors (B=0.28, p=0.021 for total behavior; B=0.13, p=0.015 for hand washing), with the exception of the preventive behavior of using additional protection at work (p=0.339). We found that fear and risk perception are associated with increased practice of hand washing and use of additional protection at work. Further studies are required on the influence of working conditions, job performance and the occurrence of mental health problems in frontline personnel with regard to COVID-19.

This article mainly proposes the point of view that financial literacy curriculum aims to make kinds of people, to make people with financial creativity of resource integration thinking and continuous ‘to conscience’ of morality, which is cultivate a way of thinking that can maximize benefits through the use of resource integration and constantly ‘to conscience’ to achieve goals for participants in financial structures with balanced interests. In this sense, this article argues that financial literacy is to make kinds of people with a financial mindset and constantly strengthen ‘to conscience’ through uniting of knowledge and action to achieve human well-being and benign operation of society. In this sense, this article attempts to determine what is really taught in financial literacy education in terms of curriculum theory. That is to improve creativity by cultivating financial thinking with constant ‘to conscience’. The views of this paper provide a new way of thinking about financial literacy education assessment. This changes the evaluation criteria of financial literacy education from the result-oriented of wealth growth to the process-oriented of financial creativity growth, trying to move the criticism of financial literacy education curriculum and evaluation from controversy to unity.

In previous studies regarding the osseointegration of zirconia (ZrO2) implants, a lack of consistency was observed in the surface topographies of the ZrO2 and Ti samples because of the difficult processability of ZrO2 surfaces. To resolve this problem, we used the molecular precursor method (wet process), which is a surface-modifying technique that can easily change the surface chemistry without changing the surface topography. A roughened Ti surface was prepared using sandblasting (large-grit) and acid treatment. We were able to create ZrO2-coated Ti implants with the same topography as that of roughened Ti substrates using the molecular precursor method, which solution contained a Zr complex. The uniform presence of tetragonal Zr was confirmed, and the apparent zeta potential of the surface of the ZrO2-coated Ti implant was higher than that of Ti. In animal experiments, ZrO2-coated Ti implants showed an equivalent or higher bone-to-implant contact ratio compared to that of the non-coated implants inserted into the femur bone defects of the rats. ZrO2 with the same surface topography as that of roughened Ti exhibits a promotion of osteogenesis equivalent to or better than that of Ti in the early stages of bone formation.

Modularity and organizational hierarchy are important concepts in understanding the structure and evolution of interactions in complex biological systems. In this work, we introduce and use a spectral characterization measure (Spectral Entropy) to quantify modularity in protein-to-protein interaction (PPI) networks in species across the tree of life. We evaluated the relation between the size of a PPI network and its (Spectral Entropy-based) modularity, and found a sigmoidal response between the two. We also found significant differences in the distribution of Spectral Entropy values among the three domains of life (Bacteria, Archaea, Eukaryotes). To explore further correlations with biological traits, we focused solely on bacterial PPI networks, which are the most numerous among the three domains and had associated trait metadata, and investigated how modularity impacts or is impacted by growth, aerobicity, selection and location on the tree of life. We found no relation between maximal growth rate and Spectral Entropy, but a strong dependence between G-C content (a proxy for selection) and Spectral Entropy. We also discovered that Spectral Entropy is negatively affected by phylogenetic placement (evolutionary distance from the last universal common ancestor). The general nature of the Spectral Entropy measure of hierarchical modularity in networks suggests that it will be useful in other settings where structural properties of real-world networks are being compared.

Molecular mechanisms for N2 fixation (solar NH3) and CO2 conversion to C2+ products in enzymatic conversion (Nitrogenase), electrocatalysis, metal-complexes and plasma-catalysis are analysed and compared. It is evidenced that differently from what present in thermal and plasma-catalysis, the electrocatalysis path requires not only the direct coordination and hydrogenation of undissociated N2 molecule, but to realize a series of features present in the Nitrogenase mechanism. There is the need of i) a multi-electron and -proton simultaneous transfer, not as sequential steps, ii) forming bridging metal hydride species, iii) generate intermediates stabilized by bridging multiple metal atoms, iv) have the capability of the same sites to be effective both in N2 fixation and in COx reduction to C2+ products. Only iron oxide/hydroxide stabilized at defective sites of nanocarbons was found to have these features. This comparison of the molecular mechanisms in solar NH3 production and relations with CO2 reduction is proposed to be a source of inspiration to develop the next generation electrocatalysts to address the challenging transition to a future sustainable energy and chemistry beyond fossil fuels.

In light of the latest trends in global installed capacities, the importance of variable renewable energy sources (VRES) to future energy supply systems is evident. Despite this, the inherent intermittency of VRES remains an obstacle to their widespread adoption. Green hydrogen is often suggested as an energy carrier that can account for this in a sustainable manner. In the analysis, a robust European energy system in the context of 2050 and with 100% VRES energy supply is designed through an iterative minimal cost-optimization approach that ensures robust security of supply over 38 weather-year scenarios (1980-2017). The impact of spatial VRES variability is factored in by defining exclusive VRES groups within each optimization region and, from this, it can be seen that higher numbers of groups in each region offer cheap electricity generation locations to the optimizer and thus decrease the total annual cost of the system. Beyond this, the robust system design and impact of inter-annual variability is identified by iteratively combining the installed capacities of different system designs obtained by applying 38 historical weather years. The robust system design outlined here has significantly lower capacities in comparison to the maximum regional capacities obtained in the first round of optimization.

Biogas contains more than 40% CO2 that can be removed to produce high quality CH4. Recently, CH4 production from CO2 methanation has been reported in several studies. In this study, CO2 methanation of biogas was performed over a 20 wt% Ni-Mg-Al catalyst, and the effects of CO2 conversion rate and CH4 selectivity were investigated as a function of CH4, O2, H2O, and N2 compositions of the biogas. At a gas hourly space velocity (GHSV) of 30,000/h, the CO2 conversion rate was ~79.3% with a CH4 selectivity of 95%. In addition, the effects of the reaction temperature (200–450 °C), GHSV (21,000–50,000/h), and H2/CO2 molar ratio (3–5) on the CO2 conversion rate and CH4 selectivity over the 20 wt% Ni-Mg-Al catalyst were evaluated. The characteristics of the catalyst were analyzed using Brunauer-Emmett-Teller (BET) surface area analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The catalyst was stable for approximately 200 h at a GHSV of 30,000/h and a reaction temperature of 350 °C. CO2 conversion and CH4 selectivity were maintained at 75% and 93%, respectively, and the catalyst was therefore concluded to exhibit stable activity.

General wisdom thinks that the central of blackholes are singular and featured by mass, charge and spin exclusively; the microstate reflected in the Bekenstein-Hawking entropy can be accounted for only in some quantum gravity. We challenge this wisdom with two exact solution families to the sourceful Einstein equation which describe dust ball with oscillatory inner structure and variety of mass profiles. We attribute the matter content's oscillation across the central point of the system to the forward scattering domination in high energy collisions induced by inter-gravitating acceleration and provide their Penrose-Carter diagram representation and quantum description briefly. Our solution family provides a very simple semi-classic picture for the micorstate definition of black holes.

Purpose: To explore the influence of education and other factors on an athlete’s decision to return to sport post-concussion injury, and whether general risk-taking tendencies are related to return to sport post-concussion decisions in these athletes. Participants and Methods: A self-administered electronic survey was designed to examine their decision-making process when faced with scenario-based questions regarding returning to sport post-concussion injury. Students from the Health Sciences and Medicine Faculty at Bond University were invited to participate. Participants were allocated to a concussion education or non-education group prior to commencement of questionnaire via the random generator on Qualtrics software function. The risk propensity scale was used to assess the risk aversion of each participant. Results: Sixteen respondents were randomized evenly to education and non-education groups. Seven (43.8%) had previously received concussion education training prior to completing the questionnaire, with one (14%) choosing to return to sport in the scenario-based questions. The education group reported two (25%) respondents return to sport, while three (75%) respondents out of four returned to sport with no education or previous concussion training. Influential factors that impacted the decision whether to return to sport or not included: game importance, concussion severity and symptoms, and various internal and external factors. Finally, there was a divergence in results from the risk propensity scale when deciding to return to sport and general risk-taking propensities. Conclusion: This study identified several influential factors including game importance, concussion severity and symptoms which play a significant role in the return to sport decisions post-concussion injury.

It has been a long time since the world has experienced a pandemic with such a rapid devastating impact as the current COVID-19 pandemic. The causative agent, the Severe Acute Respiratory Syndrome coronavirus 2 (SARS-CoV-2) is further unusual in that it appears capable of infecting many different mammal species. As a significant proportion of people worldwide are infected with SARS-CoV-2 and may spread the infection unknowingly before symptoms occur or without any symptoms ever occurring, there is a non-negligible risk of humans spreading SARS-CoV-2 to wildlife, in particular mammals. Because of SARS-CoV-2’s evolutionary origins in bats and reports of humans transmitting the virus to pets and zoo animals, regulations for prevention of human-to-animal transmission have so far focused mostly on these animal groups. Here, we summarize recent studies and reports that show that a wide range of distantly related mammals are likely susceptible to SARS-CoV-2 and that susceptibility or resistance to the virus is in general not predictable, or only to some extent, by phylogenetic proximity to known susceptible or resistant hosts. In the absence of solid evidence on the SARS-CoV-2 susceptibility/resistance for each of the >5,500 mammal species, we argue that sanitary precautions should be taken when interacting with any mammal species in the wild. Preventing human-to-wildlife SARS-CoV-2 transmission is important for protecting these (sometimes endangered) animals from disease, but also to avoid establishment of novel SARS-CoV-2 reservoirs in wild animals. The risk of repeated re-infection of humans from such a wildlife reservoir could severely hamper SARS-CoV-2 control efforts. For wildlife fieldworkers interacting directly or indirectly with mammals, we recommend sanitary precautions such as physical distancing, wearing face masks and gloves, and frequent decontamination, which are very similar to regulations currently imposed to prevent transmission among humans.

Renewable energy sources (RES) will play a crucial role in future sustainable energy systems. In scenarios analyzing future energy system designs, a detailed spatial and temporal representation of renewable-based electricity generation is essential. For this, sufficiently representative weather data are required. Most analyses performed in this context use the historical data of either one specific reference year or an aggregation of multiple years. In contrast, this study analyzes the impact of different weather years based on historical weather data from 1980 through 2015 in accordance with the design of an exemplary future energy system. This exemplary energy system consists of on- and offshore wind energy for power-to-hydrogen via electrolysis, including hydrogen pipeline transport for most southwestern European countries. The assumed hydrogen demand for transportation needs represents a hypothetical future market penetration for fuel cell-electric vehicles of 75%. An optimization framework is used in order to evaluate the resulting system design with the objective function of minimizing the total annual cost (TAC) of the system. For each historical weather year, the applied optimization model determines the required capacities and operation of wind power plants, electrolyzers, storage technologies and hydrogen pipelines to meet the assumed future hydrogen demand in a highly spatially- and temporally-detailed manner, as well as the TAC of the system. Following that, the results of every individual year are compared in terms of installed capacities, overall electricity generation and connection to the transmission network, as well as the cost of these components within each region. The results reveal how sensitive the final design of the exemplary system is to the choice of the weather year. For example, the TAC of the system changes by up to 20% across two consecutive weather years. Furthermore, significant variation in the optimization results regarding installed capacities per region with respect to the choice of weather years can be observed.

By combing continuum topology optimization (TO) method and lattice structure technique, a sandwich aircraft spoiler with a high stiffness-to-weight is designed. TO method is served to produce the shell of the aircraft spoiler and the lattice structure, used as cores, is employed to support the shell. TO problem is established as maximizing the stiffness of the structure with limited material volume. Density-based method is utilized to achieve a 0/1 solution. We then empirically replace the core of the aircraft spoiler by using 3D kagome lattice structure. Two different materials, i.e., aluminum alloy and titanium alloy, are synthetically applied to further reduce the weight and simultaneously improve the strength of the aircraft spoiler. Numerical simulations are conducted to show that the designed aircraft spoiler can meet the service environment with a reduction of its weight by approximately 80% when compared with that of the initial design model. Finally, we have fabricated the designed model with photosensitive resin by using 3D printing technique.

Drug delivery to the brain represents a challenge especially in the therapy of central nervous system malignancies. Simvastatin (SVT), as other statins, has shown potential anticancer properties that are difficult to exploit in the CNS. In the present work the physico-chemical, mucoadhesive and permeability enhancing properties of simvastatin-loaded poly-ε-caprolactone nanocapsules coated with chitosan for nose-to-brain administration were investigated. Lipid-core nanocapsules coated with different molecular weight (MW) chitosans (LNCchit) prepared by a novel one-pot technique were characterized for particle size, surface charge, particle number density, morphology, drug encapsulation efficiency, interaction between surface nanocapsules with mucin, drug release and permeability across two nasal mucosa models. Results show that all formulations present adequate particle size (below 220 nm), positive surface charge, narrow droplet size distribution (PDI<0.2) and high encapsulation efficiency. Nanocapsules presented controlled drug release and mucoadhesive properties dependent on the MW of the coating chitosan. The results of permeation across RPMI 2650 human nasal cell line evidenced that LNCchit increased the permeation of SVT. In particular, the amount of SVT permeated after 4h for nanocapsules coated with low MW chitosan, high MW chitosan and control SVT was 13.91 ± 0.78 µg, 9.15 ± 1.23 µg and 1.42 ± 0.21 µg respectively. These results were confirmed by the SVT ex vivo permeation across rabbit nasal mucosa. This study highlighted the suitability of LNCchit as promising strategy for the administration of simvastatin for a nose-to-brain approach for the therapy of brain tumors.

Location-Based Services (LBS) have been widely deployed for the connected vehicle (CV) applications such as vehicle navigation,vehicle tracking and location-based augmented reality. The current LBS deployments have limitations in supporting time-critical CV use cases, including vehicle to vehicle (V2V), vehicle to infrastructure (V2I) and vehicle-to-people (V2P) safety applications. The paper presents the new LBS framework based on the publish-subscribe communication paradigm, to enable device-to-device (D2D) connections through use of selected application protocols in the application layer of the TCP/IP layered protocol model. Two publish-subscribe application protocols, Distributed Data Service (DDS) real-time publish and subscribe (DDS-RTPS) and Message Queue Telemetry Transport (MQTT), are introduced to support the LBS D2D applications. A number of test scenarios with Mosquitto MQTT and OpenDDS under 4G-mobile broadband (MBB) services are designed to assess the transmit/receive round-trip time (RTT) and packet-loss rate (PLR) with settings of a publisher to multiple subscribers, to simulate the connections to multiple vehicles. The transmission frequency is set for 10 Hz and the message sizes vary from 100 to 2000 Bytes. The PLRs are defined as the percentages of the delayed messages beyond a delay limit. Static test results with OpenDDS show that for the RTT delay beyond the limit of 100 ms, the total PLRs range between 5.25% and 8.76% for the message size of 50 to 2000 Bytes. Vehicle testing results with Mosquitto show that PLRs for the RTT delays between 200 ms and 1000 ms are 0.63%, 3.58% and 5.77%, for connections with 1, 4 and 10 vehicles, respectively. The results demonstrate the potential of the D2D LBS framework for medium-demanding CV safety applications such as V2P and V2I use cases, taking advantages of the 4G-MBB services and 5G extreme mobile broadband (eMBB) services and mobile devices generally available with all road users.

The seasonally adjusted civilian labor force participation rate, the sum of employed and unemployed persons as a percentage of the civilian non-institutional population, is analysed in the general to specific modelling framework with a saturating set of step indicators from January 1977 through June 2018. The results indicate that, ceteris paribus, the rise in the ratio of women to men in the labor force in addition to positive demographic movements can largely account for the rise in the labor force participation rate up to January 2000. Subsequently, the aging population helps to explain the decline. Recessions play a transitory role.

The speech-to-song illusion is a type of auditory illusion that the repetition of a part of a sentence would change people’s perception tendency from speech-like to song-like. The study aims to examine how pace, emotion, and language tonality affect people’s experience of the speech-to-song illusion. It uses a between-subject (Pace: fast, normal, vs. slow) and within-subject (Emotion: positive, negative, vs. neutral; language tonality: tonal language vs. non-tonal language) design. Sixty Hong Kong college students were randomly assigned to one of the three conditions characterized by pace. They listened to 12 audio stimuli, each with repetitions of a short excerpt, and rated their subjective perception of the presented phrase, whether it sounded like a speech or a song, on a five-point Likert-scale. Paired-sample t-tests and repeated measures ANOVAs were used to analyze the data. The findings reveal that a faster speech pace could strengthen the tendency of the speech-to-song illusion. Neither emotion nor language tonality show a statistically significant influence on the speech-to-song illusion. This study suggests that the perception of sound should be in a continuum and facilitates the understanding of song production in which speech can turn into music by having repetitive phrases and to be played in a relatively fast pace.

The impact of an unlicensed low-cost taxi in Bangladesh is very severe, especially in municipal cities. Day by day the numbers of unlicensed low-cost taxi are increasing by jumping up and creating pressure on traffic and transportation system. The aim of this study is to find out the causes of increasing illegal taxi and the extent of this vehicle in the municipalities of Bangladesh. Pabna municipality is used as a case study due to the more activeness of illegal taxi then the other municipalities. To achieve the objectives, the researcher used a qualitative approach to acquire more depth about the problems. Besides a direct observation of the study area, an open-ended questionnaire survey and HIS survey were conducted. The illegal low-cost taxi is very active it was analyzed through the field survey. A statistical model was developed to understand the actual causes of increasing illegal low-cost taxi, where ten predicted hypotheses (age, education level, marital status and family member support of illegal drivers, and the variable of commuter satisfaction e.g. safety, comfort, continuous service, affordability of service, reliability of service and driver behavior) were tested. The model was run through the multiple regression analyses technique in SPSS and the result proved that education level of illegal low-cost taxi drivers, and the commuter satisfaction variable (safety and comfort) had a positive and significant effect of increasing illegal low-cost taxi in the study area. However other variable had no significant effect in case of increasing illegal low-cost taxi. Besides the safety and comfort, steady job for the operators, provision of continuous, individual and door to door service system are the main reasons for increasing the illegal low-cost taxi in the study area. Finally, the researcher concludes with the requirement of some necessary action from the responsible authority on vehicular regulation for the improvement of the local public transport system in Bangladesh.

Graph coloring is a manifestation of graph partitioning, wherein, a graph is partitioned based on the adjacency of its elements. Partitioning serves potentially as a compartmentalization for any structural problem. Vertex coloring is the heart of the problem which is to find the chromatic number of a graph. The fact that there is no general efficient solution to this problem that may work unequivocally for all graphs opens up the realistic scope for combinatorial optimization algorithms to be invoked. The algorithmic complexity of graph coloring is non-deterministic in polynomial time (NP) and hard. To the best of our knowledge, there is no algorithm as yet that procures an exact solution of the chromatic number comprehensively for any and all graphs within the polynomial (P) time domain. However, several heuristics as well as some approximation algorithms have been attempted to obtain an approximate solution for the same. Here, we present a novel heuristic, namely, the 'trailing path', which returns an approximate solution of the chromatic number within polynomial time, and, with a better accuracy than most existing algorithms. The ‘trailing path’ algorithm is effectively a subtle combination of the search patterns of two existing heuristics (DSATUR and Largest First), and, operates along a trailing path of consecutively connected nodes (and thereby effectively maps to the problem of finding spanning tree(s) of the graph) during the entire course of coloring, where essentially lies both the novelty and the apt of the current approach. The study also suggests that the judicious implementation of randomness is one of the keys towards rendering an improved accuracy in such combinatorial optimization algorithms. Apart from the algorithmic attributes, essential properties of graph partitioning in random and different structured networks have also been surveyed, followed by a comparative study. The study reveals the remarkable stability and absorptive property of chromatic number across a wide array of graphs. Finally, a case study is presented to demonstrate the potential use of graph coloring in protein design – yet another hard problem in structural and evolutionary biology.

In 1990 the Malaysian Government launched Vision 2020 with the goal of Malaysia becoming a ‘fully developed country’ by the year 2020. In this drive for development the country has been examining many of its key natural assets, exploring how to both preserve them whilst ensuring that they make the maximum possible contribution to national development goals. Endau Rompin is one of these assets, being the second largest National Park in Peninsula Malaysia. The rich tropical rainforest flora and fauna of the Park and its hinterland, however, are threatened by various anthropogenic forces, most notably deforestation and poaching; both of which have taken the Park’s flagship species - the Tiger Panthera tigris jacksoni – towards the brink of local extinction. Malaysia’s statutory East Coast Economic Region Development Council commissioned a study to consider ways of increasing tourism revenues from the Park while at the same time reversing these threats. The key conclusion drawn is that a more holistic, landscape-scale approach should be adopted, with Endau Rompin forming part of a wider strategic economic zone based around sustainable tourism and land management. The proposed expanded zone extends eastwards beyond the confines of the Park, across the coastal plain to the South China Sea, and onwards to the neighbouring Mersing Islands. This expanded zone is referred to as Malaysia’s new ‘Rainforest to Reef Region’.

The population’s mobility in urban areas is a necessary variable in the modeling of risk scenarios caused by atmospheric contamination. The inclusion of this concept makes static models more dynamic while considering people within a city to be an entity with complex mobility processes. We propose a conceptual and methodological tool to make the representation of the social, economic and territorial components, as well as the patterns in the population´s mobility to delimitate risk areas for human health by exposure of contaminants. In the volatile organic compounds (VOC), benzene, ethylbenzene, toluene and xylene (BTEX) are amongst the most dominant substances in fugitive vapor emissions in gas stations (GS). In urban areas, the exposure to BTEX by residential proximity and proximity to other facilities, which cause intra-urban agglomeration, can impact and affect human health. This model seeks to facilitate the focalization, identification and prioritization of risk areas by BTEX environmental contamination. This article goes beyond de conceptual framework. It suggests methodological and instrumental aspects to be applied in other cities. The government agencies must consider these results when establishing rules, permissions and procedures to reduce environmental pollution for managing the risk in a complex urban environment.

There is a growing concern about climate change being a serious threat to insurance business sustainability. Knowing if climate warming is a cause for claims and losses increase, and how this cause-effect relationship will develop in the future are two open major questions. In this article, we answer both questions by particularizing the geographical area of Spain, and a precise risk, hailstorm in crop insurance in the line of business of wine grapes. We measure climate change thanks to the Spanish Actuarial Climate Index (SACI). We use a database containing all the claims caused by hail risk in Spain from 1990 to 2022. With homogenized data, we consider as dependent variables the monthly number of claims, monthly number of loss costs equal to one, and monthly total losses. The independent variable is the monthly Spanish Actuarial Climate Index (SACI). We try to explain the former through the latter using regression and quantile regression models. Our main finding is that climate change as measured by SACI explains these three dependent variables. We also give an estimation of the increase of the monthly total losses Value at Risk, corresponding to a future increase in climate change measured in units of SACI. Spanish crop insurance managers should carefully incorporate these conclusions into their decision-making process to keep this line of business sustainable in the future.

Whole genome duplication (WGD) or polyploidization can occur at the cellular, tissue, and organismal levels. At the cellular level, tetraploidization has been proposed as a driver of aneuploidy and genome instability, and correlates strongly with cancer progression, metastasis, and development of drugs resistance[1–6]. WGD is also a key developmental strategy for regulating cell size, metabolism, and cellular function[1,7–10]. In specific tissues, WGD is involved in normal development (e.g. organogenesis), tissue homeostasis, wound healing, and regeneration[10–17]. At the organismal level, WGD propels evolutionary processes such as adaptation[18], speciation[19], and crop domestication[20]. An essential strategy to further our understanding of the mechanisms promoting WGD and its effects is to compare isogenic strains that differ only in their ploidy. Caenorhabditis elegans (C. elegans) is emerging as an animal model for these comparisons, in part because relatively stable and fertile tetraploid strains can be produced rapidly from nearly any diploid strain[7]. Here we review the use of Caenorhabditis polyploids as tools to understand important developmental processes (e.g. sex determination, dosage compensation, and allometric relationships)[21–27] and cellular processes (e.g. cell cycle regulation, chromosome dynamics during meiosis)[28–32]. We also discuss how the unique characteristics of the C. elegans WGD model will enable significant advances in our understanding of mechanisms of polyploidization and its role in development and disease.

The field of biosensors has found great use for surface plasmon resonance (SPR), which has attracted attention for its multiple applications. With the goal of early cancer detection at the level of a single living cell, this research numerically investigates a very sensitive D-shaped fiber-optic biosensor based on surface plasmon resonance (SPR). The titanium oxide (TiO2) is coated on gold (Au), which is utilized as a thin-film plasmonic material in the suggested biosensor structure. The guiding of light in the fiber is modeled using the finite element method (FEM) when six different types of healthy human cells and their malignant counterparts are exposed to its sensitive region. Refractive index (RI) differences between cancer cells and healthy cells are found through the analysis of the optical spectra and their amplitudes. This enables us to identify small changes in the optical characteristics of cells that could be a sign of pathogenic alterations. In this work, we concentrated on three forms of cancer: skin cancer (basal cell) and breast cancer (MDA-MB-231 and MCF-7). The results show which parameters are optimal to ensure that the sensor performs well when used to detect the three types of cancer under study. When the suggested sensor’s performance is compared to SPR sensors that have previously been published in the literature, it becomes clear that our sensor offers great promise for early cancer detection.

(1) Background: This report aims to illustrate the development, progression, diagnosis and treatment of chronically present articular surface lesions; (2) Methods: In this report, two patients are described from the point of initial presentation of symptoms to surgical consultation based on radiologic findings. These patients underwent corrective surgery in the form of mosaicplasty to repair the lesion present at the articular surface and the underlying subchondral bone. (3) Discussion: Diagnosing juvenile OCD remains challenging due to variable clinical presentation and minute radiologic discoveries. X-rays are useful, however, the gold standard remains to be arthroscopy which can be both diagnostic and therapeutic. Future prospects include the use of novel sonographic methods and the use of artificial intelligence within the given modalities. (4) Conclusions: The detailed imaging provided by MRI, combined with the insights from X-rays and potentially other modalities, allows for a nuanced understanding of the disease. This comprehensive approach ensures that treatment decisions are well-informed, optimizing outcomes for young patients with this condition.

Magnetic Fe3O4 nanoparticles (MNPs) are becoming more important every day in drug targeting. We prepared here MNPs in a simple one-step reaction by following the solvothermal method assisted by azide and alkyne functionalized polyethylene glycol (PEG400) polymers, as well as by PEG6000 and the polyol -cyclodextrin (CD). The composition, morphology, and structure of the nanospheres were characterized using Transmission Electron Microscopy (TEM), Nuclear Magnetic Resonance (NMR), X-Ray Diffraction Diffractometry (XRD), Atomic Force Microscopy (AFM), Fourier-Transform Infrared Spectroscopy (FT-IR), Matrix-Assisted Laser Desorption/Ionization (MALDI) and Vibrating Sample Magnetometry (VSM). The obtained nanoparticles (@Fe3O4-PEGs and @Fe3O4-CD) showed diameters between 90-250 nm, depending on the polymer used and the Fe3O4·6H2O precursor concentration, typically, 0.13 M, 200 °C, and 24 h of reaction. MNPs exhibited superparamagnetic properties with high saturation of magnetization at room temperature, reaching values of 59.9 emu/g (@Fe3O4-PEG6000), and no ferromagnetism. Likewise, they showed temperature elevation after applying an alternating magnetic field (AMF) in all cases, obtaining Specific Absorption Rate (SAR) values of up to 51.87 ± 2.23 W/g in the case of @Fe3O4-PEG6000. Both PEGs and the βCD played a crucial role as electrostatic stabilizers in the formation of Fe3O4 nanospheres, providing a polymeric/polyol coating around the magnetic cores. Additionally, the formed systems are susceptible for click chemistry, as was demonstrated in the case of the cannabidiol-propargyl derivative (CBD-Pro), which was synthesized and covalently attached to the azide functionalized surface of the system @Fe3O4-PEG400-N3. Prepared MNPs are highly dispersible in water, remaining in suspension for over 3 days, and non-toxic in the T84 human colon cancer cell line, indicating that they are ideal candidates for biomedical applications.

The properties of coatings obtained using two surface preparation methods were compared: heating and etching by ion bombardment with plasma generation by arc evaporators and heating and etching by a glow discharge. A Ti-TiN-(Ti,Cr,Al)N coating was deposited. The use of a glow discharge provides better resistance of the coating to destruction during the scratch test and wear resistance of metal-cutting tools when turning steel. As the cutting speed increases, the advantage in wear resistance of the coating deposited using a glow discharge increases. During the process of heating and etching by ion bombardment with metal ions, a nanolayer rich in cobalt and tooling elements (iron, molybdenum) is formed in the area of the interface of the coating and the carbide substrate. When heated and etched by a glow discharge, such a layer does not form. When using both methods, there is identical diffusion of tungsten into the coating and diffusion of chromium and possibly titanium into the substrate. Thus, the glow discharge heating and etching method can be effectively used in the process of PVD coating deposition.

Sandblasting materials used for dental restoration is a valuable preconditioning technique enhancing the physical properties and promotes osseointegration and cell adhesion. Ti medical grade 4 and Ti6Al4V were blasted with a series of various naturally occurring and synthetically produced spraying materials of controlled granulometry, at precise spraying duration and spraying pressure, and the results were analyzed in terms of the obtained surface roughness and by SEM analysis. It was found that in all cases, regardless of the spraying material or working conditions, the roughness profile achieved is a uniformly distributed one. A reduction in the blasting pressure by half led to a decrease in the roughness between 30 and 35%. The use of glass balls as blasting material led to decreased roughness and a more uniformly distributed roughness values for Ti as well as for Ti6Al4V regardless of spraying duration or applied pressure comparing to other spraying materials, and blasting with olivine led to increased, as well as uniformly distributed values, and hence the conclusion that one may control the roughness size by choosing one or another from the above materials, without the need of changing any other operating parameters. In the case of Ti, the achieved roughness is greater than in the case of Ti4Al6V, irrelevant of the blasting material, the differences being smaller the softer the sandblasting material due to the fact that Ti alloys have better mechanical properties and increased hardness comparing to pure Ti. SEM analysis showed that the use of sintered hydroxyapatite as an additive to the blasting material does not necessarily lead to a substantial deposition of hydroxyapatite on the substrate materials, only traces of it being identified during the analysis.

This study was conducted to investigate heavy metal contamination and potential health risk of ground water of selected municipal solid waste (MSW) disposal sites of Khyber Pakhtunkhwa (KP) Pakistan. For this purpose a total of 30 composite samples of both surface and ground water were collected from dumpsites of Abbottabad, Bannu and Peshawar. The collected samples were analyzed for physico-chemical parameters and heavy metals by following standard methods. Results indicated that pH values were found within the acceptable limits specified by national environmental quality standards (NEQS) and world health organization (WHO). Mean concentrations of heavy metals were within NEQS and WHO limits, except for Ni which exceeded the NEQS and WHO limit of 0.02 mg/L in all samples, Similarly, Mn exceeded the limit set by NEQS and WHO (0.5 mg/L) in the ground water samples collected from Bannu dumpsite. The multivariate analysis indicated that the heavy metal contamination of the groundwater of the selected dumpsites was anthropogenic. The pollution index (PI) values (PI≥100) of Mn and Ni indicated very high pollution at individual levels while collectively based on heavy metals pollution index (HPI) values (HPI ≥ 200) the ground water of all the selected dumpsites were found highly polluted. Whereas, the hazard index (HI) values (HI ≥ 5) suggested adverse health effects. It was concluded that the ground water of all the dumpsites was highly polluted with heavy metals particularly Ni and Mn thus, posing a high health risk.

Amid increasing deforestation, surface fires reaching the forest understory are one of the primary threats to Amazonian ecosystems. Despite extensive research on post-fire mortality in woody species, literature on palm resilience to fire is scant. This study investigates post-fire mortality in four understory palms—Bactris maraja Mart., Chamaedorea pauciflora Mart., Geonoma deversa (Poit.) Kunth, Hyospathe elegans Mart., and juvenile individuals of Euterpe precatoria Mart. Objectives included: a) comparing post-fire responses; b) developing mortality models based on severity variables; and c) evaluating if diameter protects bud stems from heat flux. Conducted at the edge of an Ombrophylous Forest in Alto Juruá Acre, Brazil (7°45'S, 72°22'W), the experiment subjected 85 individuals to controlled burning in a 1 m² area near the stipe, with temperature sampling using K thermocouples. Results showed varying mortality rates among species, with larger stipe diameter correlating to reduced mortality. Canopy burning patterns significantly influenced mortality, especially for Euterpe precatoria. Species exhibited diverse regrowth capacities, with B. maraja showing the highest number and tallest basal resprouts. This study underscores post-fire plant mortality as a critical indicator of fire severity, essential for understanding its ecological impacts.

This study aimed to compare the flexural strength, surface roughness, and microhardness of a resin for three-dimensional (3D) printing and a conventional composite resin and to evaluate whether the printing orientation influences these properties. To evaluate the flexural resistance, test specimens were produced and divided into four groups: three groups of resins for 3D printing with inclinations of 0°, 45°, and 90°, and one group of conventional composite resin. Forty discs were produced and subjected to a sandpaper-polishing sequence, and the surface roughness was measured using a roughness meter. The Vickers microhardness test was performed at three different points, and the average was obtained. The results were subjected to ANOVA statistical analysis and Tukey's test. There were statistical differences in the flexural strength and microhardness between the conventional resin and the resin used for 3D printing. No statistical difference in surface roughness was observed. The resin for 3D printing exhibited lower flexural strength and microhardness than conventional composite resins. We concluded that the resin for 3D printing had lower flexural strength and hardness than the conventional composite resin but similar surface roughness. The printing orientation did not affect the flexural strength, whereas the hardness increased as the printing angle increased.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

The digital model of airborne frequency selective surface radomes (AFSSRs) is the basis of design, simulation analysis, manufacturing, and other related research of AFSSRs. This paper proposes a rapid modeling method of AFSSRs based on dynamic customizable primitives. Firstly, a layered digital model construction scheme of AFSSR is presented based on the typical radome wall structure. Then, according to the characteristics of various surface configurations and complex wireframe information of AFSSRs, the dynamic primitives are raised to express the boundary and contour information of all kinds of radomes. Focusing on the undevelopable characteristics of the aero-dynamic shape surface of the AFSSR, the arrangement solution and mapping method for frequency selective elements on undevelopable surfaces are proposed. Furthermore, the imple-mentation logic of this method on the creation of each layer model and the assembly of the whole machine model is introduced. Finally, according to this method, a rapid modeling system (RMS) is established, and the modeling effect and efficiency of the RMS are demonstrated and compared, which verifies the feasibility and effectiveness of this method.

The performance of Yttrium-Barium Copper Oxide (YBCO) high-temperature superconductors in high-frequency applications is significantly affected by the microwave surface resistance (Rs). The paper delves into the basics, measuring methods and factors affecting the resistance (Rs) in YBCO, highlighting its high critical temperature (Tc) and low resistance, positioning it as a promising material. YBCO's compatibility with epitaxial growth and microstructure engineering offers opportunities to reduce grain boundary effects and improve Rs, making it advantageous for high-frequency electronics, communication systems, and MRI coils. This is due to its high critical current density (Jc) and exceptional Rs at practical temperatures. Challenges remain in comprehending and managing Rs in YBCO, despite its favorable characteristics. Utilizing advanced fabrication methods and incorporating nanotechnology allow for customization of YBCO-based devices. Multi-scale modeling and simulation are essential for guiding experimental work and understanding YBCO's performance in high-frequency settings. This study highlights the promise of YBCO for future high-frequency technologies and stresses the importance of more research to overcome hurdles and fully exploit its capabilities, potentially transforming superconducting devices for practical use.

Microencapsulation by atomization can be used to minimize the loss of bioactive compounds, improving the characteristics and applicability of the powdered product. This study evaluates the effect of different encapsulating agents (maltodextrin, gum arabic, and chitosan) and three spray nozzle diameters (1.0, 1.2, and 1.5 mm) on the atomization of guavira (Campomanesia adamantium) pulp with added 6% bocaiuva (Acrocomia aculeata) dehydrated pulp in the green maturation stage. The experiment followed a simplex-centroid mixed design, with carrier agent concentrations and spray nozzle diameters as independent variables and powder yield, solubility, hygroscopicity, and vitamin C content as dependent variables. The results show that gum arabica increased powder yield and vitamin C retention. The addition of maltodextrin resulted in powders with increased solubility and low hygroscopicity. Furthermore, the optimization tool indicated that the best process conditions were achieved with the addition of gum arabic (10.8%) and chitosan (7.2%), resulting in powders with 29.48% yield, 82.96% solubility, 15.90% hygroscopicity and 741.11 mg/100g vitamin C. Furthermore, the 1.0 mm diameter spray nozzle was considered the most suitable for obtaining guavira pulp microparticles with higher ascorbic acid content.

This is an exercise to explore the concentration of Lithium, Lithium-7 isotope and the possible presence of black dirty ice in the lunar surface using spectral data obtained from the Clementine mission. The main interest in tracing the lithium and presence of dark ice in the lunar surface are closely related to future human settlement missions in the Moon. We investigate the distribution of Lithium and 7 Li isotope on the Lunar surface, employing spectral data from the Clementine images. We utilized Visible (VIS-NIR) imagery at wavelengths of 450, 750, 900, 950, and 1000 nm, along with Near-Infrared (NIR-SWIR) at 1100, 1250, 1500, 2000, 2600, and 2780 nm, encompassing 11 bands in total. This dataset offers a comprehensive coverage of about 80% of the lunar surface, with resolutions ranging from 100 to 500 meters, spanning latitudes from 80°S to 80°N. In order to extract quantitative abundance of Lithium, ground truth sites were used to calibrate the Clementine images. Samples (12045, 15058, 15475, 15555, 62255, 70035, 74220 and 75075) returned from Apollo missions 12, 15, 16 and 17 have been correlated to the Clementine VIS-NIR bands and five spectral ratios. The 5 spectral ratios calculated synthesize the main spectral features of sample spectra that were grouped by their Lithium and 7 Li content using Principal Component Analysis. The ratios spectrally characterize substrates of anorthosite, silica-rich basalts, olivine-rich basalts and High-T mare basalts and Orange soils. Our findings reveal a strong linear correlation between the spectral parameters and the lithium content in the 8 Apollo samples. With the values of the 11 Clementine bands and the 5 spectral ratios for each of the 8 lunar soils we performed linear regression models to estimate the concentration of Lithium and 7 Li. Also, we calculated Digital Terrain Models (DTMs; Altitude, Slope, Aspect, DirectInsolation and WindExposition) from LOLA-DTM to discover relations between relief and spatial distribution of the extended models of lithium and 7 Li. The analysis was conducted in a mask polygon extracted from Lunar Orbiter Laser Altimeter (LOLA) and located around the Apollo 15 landing site. This analysis seeks to uncover potential 7 Li enrichment through spallation processes, influenced by varying exposure to solar wind. To explore the possibility of find ice mixed with regolithe (black ice) we used a spectral library (350-2500nm) form ices dirty with different concentration of volcanic particles.

Unmanned aerial vehicle (UAV) photogrammetry allows the generation of orthophoto and digital surface model (DSM) rasters of a terrain. However, DSMs of water bodies mapped using this technique often reveal distortions in the water surface, thereby impeding the accurate sampling of water surface elevation (WSE) from DSMs. This study investigates the capability of deep neural networks to accommodate the aforementioned perturbations and effectively estimate WSE from photogrammetric rasters. Convolutional neural networks (CNNs) were employed for this purpose. Two regression approaches utilizing CNNs were explored: direct regression employing an encoder and solution based on prediction of the weight mask by an encoder-decoder architecture, subse-quently used to sample values from the photogrammetric DSM. The dataset employed in this study comprises data collected from five case studies of small lowland streams in Poland and Denmark, consisting of 322 DSM and orthophoto raster samples. Each sample corresponds to a 10 by 10 meter area of the stream channel and adjacent land. A grid search was employed to identify the optimal combination of encoder, mask generation architecture, and batch size among multiple candidates. Solutions were evaluated using two cross-validation methods: stratified k-fold cross-validation, where validation subsets maintained the same proportion of samples from all case studies, and leave-one-case-out cross-validation, where the validation dataset originates entirely from a single case study, and the training set consists of samples from other case studies. The proposed solution was compared with existing methods for measuring WSE in small streams using a drone. The results indicate that the solution outperforms previous photogrammetry-based methods and is second only to the radar-based method, which is considered the most accurate method available. The solution is characterized by a high degree of explainability and generalization.

In this study, nano-diamond (ND) and MoS2 powder are used as additives in a carbonyl iron based magnetorheological fluid (MRF) to improve its tribological performance. MRFs are prepared by dispersing 35 wt.% of CI particles in silicone oil, and adding different proportions (0, 1, 3 or 5 wt.%) of ND and MoS2 additives. Seven kinds of MRFs are made and tested using reciprocating friction and wear tester under different normal loads, and then the friction characteristics are evaluated through analyzing experiment results. The morphology properties of MRFs and contacting surfaces before and after tests are also observed using a scanning electron microscope and analyzed by energy-dispersive X-ray spectroscopy. The results show that the appropriate weight percentage of MoS2 additives may decrease friction coefficient and wear zone. It is also demonstrated from the detailed analyses of worn surfaces that the wear mechanism is influenced not only by additives but also by applied normal load and magnetic field strength.

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

MIPs inspired by antigen-antibody interactions have received substantial interest as a biomimetic artificial receptor system in environmental applications. Herein, we present a molecularly imprinted surface plasmon resonance (SPR) sensor integrated with Au nanoparticles for the identification of bisphenol A (BPA), an endocrine-disrupting chemical. The synthetic wastewater samples were analyzed to ensure the method's reliability and feasibility. Under ideal conditions, the suggested approach performed well in terms of analytical performance to BPA, with a wide linear range of 0.1 to 10 ppb and LOD of 10 ng/L. The sensor results and the Langmuir adsorption model have good agreement. It has also been shown that repeated use of the biosensor can be achieved. According to selectivity studies, BPA adsorbed within the imprinted cavities favorably compared to 4-nitrophenol and phenol. The produced BPA-imprinted SPR sensor provides improved sensitivity based on the signal amplification strategy, unconjugated sensing without the need for labeling, real-time sensing, low sample consumption rates, quantifiable assessment, and very good kinetic rate constant calculation in actual samples. Also, because the produced sensor is reusable with relative standard deviations (RSD)<1.25, indicating the sensor's accuracy, the SPR-based biomimetic BPA sensor is simple to practice and may be an economical option.

This paper proposes to combat active eavesdropping by intelligent reflecting surface (IRS) backscatter techniques. To be specific, the source (Alice) sends the confidential information to the intended user (Bob), while the eavesdropper (Willie) transmits jamming signal to interrupt the transmission for more data interception. To enhance the secrecy, an IRS is deployed and connected with Alice through fiber to transform the jamming signal into the confidential signal by employing backscatter techniques. Based on the considered model, an optimization problem is formulated to maximize signal-to-interference-plus-noise ratio (SINR) at Bob under the constraints of the transmit power at Alice, the reflection vector at the IRS and the allowable maximum SINR at Willie. To address the optimization problem, an alternate optimization algorithm is developed. The simulation results verify the achievable secrecy gain of the proposed scheme.

River bed materials serve multiple environmental functions as a habitat for aquatic invertebrates and fishes. At the same time, the particle size of the bed material reflects the tractive force of the flow regime in a flood and provides useful information for flood control. The traditional river bed particle size surveys, such as sieving, require time and labor to investigate river bed materials. The authors proposed a method to classify aerial images taken by unmanned aerial vehicle (UAV) using convolutional neural networks (CNN), our previous study showed that terrestrial riverbed material could be classified with high accuracy. In this study, we attempted to classify riverbed materials distributed in shallow waters where the bottom can be seen from UAVs. After training the CNN to classify the images with the same grain size as being in the same class even if the surface flow types taken overlapping the riverbed material were different, the total accuracy reached 90.3%. Moreover, the proposed method was applied to the wide-ranging area to determine the distribution of the particle size. In parallel, the microtopography was surveyed using Lidar-UAV, and the relationship between the microtopography and particle size distribution was discussed. In the steep section, coarse particles were distributed and formed a rapid. Fine particles were deposited on the upstream side of those rapids, where the slope had become gentler due to the damming. There was good agreement between the microtopographical trends and the grain size distribution.

A tunable near-infrared surface plasmon resonance (SPR) biosensor based on gate-controlled graphene plasmons is investigated theoretically. The novel characteristics of chemical potential sensing make the proposed sensor promising in the application of ultra-sensitive and highly specific biosensing technology. The sensitivity of chemical potential sensing in wavelength interrogation mode can be calculated to be 1.5, 1.89, 2.29, 3.21, 3.73 and 4.68 nm/meV respectively at the central wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. The much smaller full width half maximum (FWHMs) comparing with that of 2D nanomaterial-enhanced metal SPR sensors indicates higher figure of merit. The sensitivity of chemical potential sensing in gate voltage interrogation mode also can be calculated to be 156.9822, 143.6147, 131.0779, 111.0351, 101.3415 and 90.6038 mV/meV respectively at the incident wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. It can be estimated theoretically that the limit of detection (LOD) in DNA sensing of the proposed sensor can reach femtomolar level and even attomolar level, comparable to and even lower than that of 2D nanomaterial-enhanced metal SPR sensors with AuNPs as a sensitivity enhancement strategy. The feasibility of preparation and operation of this new concept SPR biosensor is also analyzed and discussed.

The objective of this work was to improve the thermal stability, flame resistance and surface properties of black poplar (Populus nigra L.) wood via different impregnation methods. The impregnation method was employed through two distinct modalities: vacuum impregnation and immersion impregnation. Here, poplar wood was impregnated with calcium oxide solutions (1%, 3% and 5%). Fourier transform infrared spectroscopic analysis revealed a shift in the typical peaks of cellulose, hemicellulose, and lignin depending on the impregnation method and solution ratio. Thermogravimetric analysis and the limiting oxygen index indicated that the samples impregnated with lime solutions exhibited higher thermal stability than the unimpregnated wood. In both impregnation methods caused a decrease water absorption and thickness swelling of the sample groups. Using a scanning electron microscope, the effect of the impregnation process on the structure of the wood was examined. In terms of surface properties, it was determined that the surface roughness value increased. On the contrary, it was observed that the contact angle value also increased. A significant difference emerged between the applied methods. In conclusion, the applied lime minerals are suitable substances to increase flame resistance and thermal stability of black poplar wood.

In the current industrial revolution, advanced technologies and methods can be effectively utilized for the detection and verification of defects in high-speed steel filament production. This paper introduces an innovative methodology for the precise detection and verification of micro surface defects found in steel filaments through the application of the Eddy current principle. Permanent magnets are employed to generates a magnetic field with high frequency surrounding a coil of sensor positioned at the filament's output end. The sensor's capacity to detect defects is validated through a meticulous rewinding process, followed by a thorough analysis involving scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). Artificial defects were intentionally introduced into a sample, and their amplitudes were monitored to establish a threshold value. The amplitude signal of these created defect was identified at approximately 10% FSH, which corresponds to a crack depth of about 20 µm. In the experimental production of 182 samples covering 38 km, the defect ratio was notably high, standing at 26.37%. These defects appeared randomly along the length of the samples. The verification results underscore the exceptional precision achieved in the detection of micro surface defects within steel filaments. These defects were primarily characterized by longitudinal scratches and inclusions containing physical tungsten carbide.

The grinding process by friction at the micro-scale in a mill with stones is considered a variable combination of contacts: with two-body (the asperities of lower millstone in direct contact with the asperities of upper millstone) and the three-body (micro-particles of ground seeds trapped between the asperities of lower and the upper stones of the mill). Three elements are described: (1) the mechanic contact of the asperities of the lower and upper millstone, to predict pressures on asperities, by modeling; (2) tests on a millstone sample covered with grinding particles, and (3) tests on a wafer sample formed by the millstones with the grinding particles between them. The paper highlights the combined effects of the micro-scale friction by individual measurements and to sum these effects an analytical model was used, and to validate the model, several experiments were performed. A suitable grind by friction assumes the grain’s movement and the interaction between the seeds and solid surfaces and is highlighted through theoretical and experimental studies. Topography analysis of the surface of the millstones revealed the model of microscopic frictional force. Endpoint measurements (the traces of the surface topography evolution), enable model verification in the grinding process.

The aim of this study was to evaluate the emulsification properties of garlic water-soluble compounds (GWSC) after heat treatment (10 min at 95 °C) or pH adjustments (2.5, 3.5 and 7.8). After the various treatments, the extracts were used as such or filtrated (0.45 µm) and 10% soybean oil-in-water emulsions were prepared using low (0.48%) or high (6.55% wt/wt) extract concentrations. Whereas at low GWSC concentration, both heating or acidifying resulted in the formation of bigger oil droplet sizes (i.e. from d32=0.36 µm using unmodified extract, to d32=7–22 µm µm at pH 2.5 with or without extract filtration), the effects were opposite at the highest GWSC concentration. In the latter, heat treatment clearly reduced the droplet size as observed from the micrographs as well as the degree of creaming, though the occurrence of depletion and/or bridging flocculation was still strong. The acidification of the extract at this high GWSC concentration, significantly reduced the droplet size as observed from the micrographs but a strong flocculation was observed. Removal of protein aggregates, and possibly also saponin micelles from the extract, resulted in an obvious increase in emulsion droplet size. This research brings valuable insights on the study and utilisation of novel natural food emulsifiers from plant sources.

The cost effective design of tidal turbines requires a good estimation of the loading cycles and their extrema that are related to the unsteady fluctuations of the current velocity. Apart from the ambient turbulence, the main source of velocity fluctuations is the presence of surface waves. In the present study, we analyse the effect of waves propagating against the current on the performance and the loads of a twin vertical axis tidal turbine by an experimental approach at a 1/20 scale. Overall, the results show little or no effect of the waves on the average power and loads compared to the condition with current only, but a significant impact on their standard deviation that rises linearly with the waves amplitude. The drag, lift and pitching moment show extended ranges up to 7.5 times higher and extreme values exceedance by 60 to 100 % with irregular waves compared to the condition without waves. Those load and power fluctuation increase are fully due to the presence of waves as the coherence function between the rotor torque or the loads and the velocity spectra exceed 0.5 on the whole wave frequency bandwidth. The results also reveal a rotational sampling of the waves by the rotors that had also been observed on horizontal axis turbines. From a structural design point of view, the authors recommand to conduct tests in irregular wave conditions as the loads range and extreme values are 1.5 to 2 times higher than those encountered with regular waves of the same significant height and period.

The aerospace industry demands high-performance materials that can withstand extreme conditions and maintain efficiency in a variety of applications. Bio-inspired polymer coatings have emerged as a promising approach to meet these demands, by drawing inspiration from natural systems to develop new coatings that exhibit enhanced properties, such as self-cleaning, anti-icing, thermal management, and corrosion resistance. In this review, recent developments in the field of bio-inspired polymer coatings for aerospace applications are presented, covering a range of coatings and their respective properties. We discuss the recent developments and applications of bio-inspired coatings, with a focus on their advantages and challenges in aerospace applications. We also highlight the potential for future research and development in this field, including the integration of advanced technologies such as nanotechnology and additive manufacturing. The review aims to provide insights into the current state-of-the-art of bio-inspired polymer coatings for aerospace applications and to inspire further research in this rapidly growing field.

This work introduces a novel numerical method designed to address three-dimensional unsteady free surface flows incorporating integral viscoelastic constitutive equations, specifically, the K-BKZ-PSM (Kaye–Bernstein, Kearsley, Zapas - Papanastasiou, Scriven, Macosko) model. The new proposed methodology employs a second-order finite difference approach along with the deformation fields method to solve the integral constitutive equation, and the marker-particle method (known as \emph{Marker-and-Cell}) to accurately capture the evolution of the fluid's free surface. The newly developed numerical method has proven its effectiveness in handling complex fluid flow scenarios, including confined flows and extrudate swell simulations of Boger fluids. Furthermore, a new semi-analytical solution for velocity and stress fields is derived, considering fully developed flows of a K-BKZ-PSM fluid in a pipe.

Nano- and micro-sized CeO2 surface layers based on titanium alloy TiAl6V4 were obtained by magnetron sputtering with or without subsequent annealing. The structure of the samples was determined using scanning electron microscopy, Auger electron spectroscopy, energy dispersive spectroscopy, and X-ray diffraction. Hardness was measured by sclerometry. A direct linear dependence of the thickness of the surface layers on the deposition time and an extreme dependence, passing through a maximum, on the power are shown. A decrease in hardness with an increase in the thickness of the cerium oxide coating was noted. An increase in surface roughness, delamination and loosening of the surface layer, presumably associated with annealing, were noted. In samples with a surface layer thinner than 715 nm without annealing and 750 nm after annealing, the formation of a sublayer of TiO2, Al2O3, and Ce(VO4) was found, and in annealed samples with a layer length of less than 300 nm, all cerium dioxide reacted with vanadium dioxide to form vanadate.

In this paper, we describe the surface modification of Polytetrafluoroethylene (PTFE) through plasma treatment process. Several parameters including different active gases; RF power; dis-tance between the plasma source and sample; and plasma duration were optimized to reduce the hydrophobic nature of PTFE. Three different active gases were used [i.e., N2, O2 and (Ar+H2)], in which N2 was effective to reduce the hydrophobicity of PTFE within shorter plasma duration of 2 minutes. Several surface characterizations including ATR-FTIR, water contact angle, FE-SEM and XPS were utilized to verify the neat and modified PTFE surface after plasma treatment. The plasma treatment using N2 as an active gas improved the wettability of PTFE membrane, show-ing a water contact angle of 108° when compared with the neat PTFE (140°). The SEM images of plasma treated PTFE shows greater modifications on the surface indicating non-uniform fiber alignment and torn fibers at several places. The obtained results confirm the fact that plasma treatment is an effective way to modify the PTFE surface without altering its bulk property.

Non-alcoholic fatty liver disease (NAFLD) is a liver disorder that has become a global health concern due to its increasing prevalence. Currently, there is a need for reliable biomarkers to aid in the diagnosis and prognosis of NAFLD. Extracellular vesicles (EVs) are promising candidates in biomarker discovery, as they carry proteins that reflect the pathophysiological state of the liver. In this review, we developed a list of EV proteins that could be used as diagnostic biomarkers for NAFLD. We employed a multi-step strategy that involved reviewing and comparing various sources of information. Firstly, we reviewed papers that have studied EVs proteins as biomarkers in NAFLD, as well as papers that have studied circulating proteins as biomarkers in NAFLD. To further identify potential candidates, we utilized the EV database Vesiclepedia.org to qualify each protein. Finally, we consulted the Human Protein Atlas to search for candidates' localization, focusing on membrane proteins. By integrating these sources of information, we developed a comprehensive list of potential EVs membrane protein biomarkers that could aid in the diagnosis and monitoring of NAFLD. In conclusion, our multi-step strategy for identifying EV-based protein biomarkers for NAFLD provides a comprehensive approach that can also be applied for other diseases. The protein candidates identified through this approach could have significant implications for the development of non-invasive diagnostic tests for NAFLD and improve the management and treatment of this prevalent liver disorder.

The impact induced by cavitation bubble collapse can be utilized for mechanical surface treatment to improve fatigue properties of metals including additive manufactured metallic materials. A peening method using cavitation impact induced by a pulsed laser is called “laser cavitation peening (LCP)”. Normally, a Q-switched Nd:YAG laser, whose pulse width is a few nanoseconds, is used for LCP, which improves the fatigue strength. The problem with LCP is that the processing time is too slow. If a laser pulse whose pulse width is a few hundred microseconds can be utilized for LCP, the repetition frequency can be increased drastically using other types of laser systems such as a fiber laser. In the present paper, in order to reveal the possibility of LCP using a pulsed laser width of a few hundred microseconds, the use of LCP with a normal-oscillation Nd:YAG laser (pulse width ≈ 200 us) was investigated. It is demonstrated that LCP with the normal-oscillation Nd:YAG laser produced curvature in an aluminum alloy plate.

The surface behavior of the ZnO-based films could be modulated via a postannealing and ultraviolet (UV) irradiation with different powers and time, respectively. These present results could provide modulate the microstructure related in grain-size distribution and photocatalytic behavior for potential guide in the field of wide bandgap semiconducting oxides. The ZnO films were prepared onto Corning-1737 glass substrates by using radio-frequency magnetron sputtering without supplying oxygen source at room temperature. For the purpose of obtaining modulable grain microstructures, the as-prepared ZnO films (Z0) were treated via a postannealing modification in vacuum furnace at 300°C for 30 minutes after deposition (Z300) accompanied with the adjustable internal stress. The contact angle (CA) value of ZnO film reduced from 95° to 68° was owning to the different grain microstructure accompanied by a change in size variation. In addition, the UV light with different irradiation powers could also be used to improve the hydrophilicity varied from hydrophobic status to superhydrophilic status due to the desirable surface characteristics of the photocatalytic action. In addition, the photocatalytic activity of ZnO film exhibited efficient photodegradation of methylene blue (MB) under UV irradiation, with a chemical reaction constant of 2.93×10-3 min−1. In this present work, we demonstrated that the CA value of the ZnO films not only caused from hydrophobic to hydrophilic status accompanied by a change in grain size combined with internal stress but also induced by the UV light irradiation combined with photocatalytic activity simultaneously. On the other hand, the enhanced surface plasmonic resonance could be observed that is due to couple electron and photon oscillations and can be generated at the interface between a flat, continuous Pt capping nanolayer. This designed structure could also be considered as a Pt electrode pattern onto ZnO (metal Pt/ ceramic ZnO) for multifunctional heterostructured sensors and devices in near future.

Iapetus, a Saturn moon, shows the most differentiated albedo dichotomy of the Solar System. The dark leading side has a lower albedo than the bright trailing side. Spectral data on the visible light reveal the existence of two types of materials on the surface. The darkening in the leading side is thought to be originated by the presence of organic material and carbonaceous compounds on surface, while the trailing side is covered by water ice due to migration processes from the dark side. On airless bodies like Iapetus, the surface escape speed is greater than the speed of water molecules, resulting in the retention of a H2O atmosphere that allows some species to get diffused through it. Here, there were performed simulations of the evolution of the surface temperature for each of the two hemispheres of Iapetus. The results showed a slow yet steady increment of temperatures for both sides, with a steeper slope for the dark hemisphere. It was also simulated how much energy budget can be accumulated in both sides and its consequences. Finally, we calculated the diffusion coefficients for ammonia, methane, and water ice. The results let us infer how these compounds could evolve over time.

Films obtained from a main biopolymer phase of fish gelatin (GelA, 3% w/w) encapsulated with cinnamon essential oil (CEO, 0.03 – 0.48% v/w) and loaded with bacterial cellulose nanocrystals (BCNCs, 0.06% w/w) at pH = 3.5 were characterized. CEO-GelA/BCNCs films were prepared by casting and analyzed in terms of thickness, light transmittance (TT) and haze (H), surface hydrophobicity, tensile properties, chemical composition, and water solubility (WS). All tested films displayed outstanding optical properties (TT &gt; 89.4%), with haze slightly exceeding a 3% value only when the highest CEO loading was used during nanoemulsion preparation. The CEO plasticizing effect yielded an increase in the elongation at break (EAB, from 0.84% up to 3.79%), which corresponded to a decrease in tensile strength (TS, from 8.98 MPa down to 1.93 MPa). The FT-IR spectra of films revealed a good degree of interaction among single nanoemulsion components via hydrogen bonding. The intrinsic hydrophobic nature of the CEO negatively impacted the WS (from 52.08% down to 8.48%) of the films. Results obtained in this work confirmed the possibility to produce packaging systems from renewable sources to be potentially used in the form of edible films/coatings for preserving water-sensitive food products, both vegan-based (fruits/vegetables), and animal-based (meat/seafood).

Pollution of urban surface dust with hazardous elements (HEs) is a serious environmental issue due to its toxicity and potential hazardous effects. Surface dust samples were collected from core urban, urban, and suburban gradients in the Urumqi city of the arid NW China, and the concentrations of six HEs, such as arsenic (As), cadmium (Cd), nickel (Ni), lead (Pb), mercury (Hg), and chromium (Cr), were determined. The pollution load index (PLI) and the US EPA health risk assessment model were applied to analyze and compare the pollution levels and potential health risk of HEs in surface dusts in different urbanization gradients. The obtained results indicate that the average concentrations of Hg, Cd, and Ni in surface dust decrease in the order of core urban > urban > suburban, whereas the average concentrations of As, Cr, and Pb decrease in the order of urban > core urban > suburban. The PLI of HEs in surface dust decreased in the order of core urban > urban > suburban. The concentrations of HEs in the core urban and urban gradients are relatively higher than in the suburban gradient. Furthermore, the total non-carcinogenic and carcinogenic risk index of investigated HEs in surface dust decrease in order of urban > core urban > suburban, for both adults and children. In addition, the pollution of surface dust with HEs in all urbanization gradients is more harmful to the children's health than to the adults. Overall, the potential non-carcinogenic and carcinogenic health risks of the investigated HEs, instigated primarily by oral ingestion of surface dust, are found to be within the acceptable range. However, urbanization can effects the accumulation of HEs in surface dust, and Cr is the main non-carcinogenic risk factor, whereas Cd is the main carcinogenic risk factor among the analyzed HEs in surface dust in all urbanization gradients.

The purpose of this study was to describe ocular surface and anterior eye segment findings in various types of ichthyoses. Methods: This was a single-center prospective observational study. The study group consisted of five patients (P1-P5) aged 13–66 years. Multimodal imaging was performed, including slit-lamp examination, swept-source optical coherence tomography (SS-OCT), and in vivo confocal microscopy (IVCM). Results: All patients were diagnosed with moderate to severe dry eye disease (DED). Corneas showed a significant pattern of irregularity, with a significant difference between the corneal thickness at the apex (CAT) and corneal thinnest thickness (CTT), ranging from 5 to 375 µm. Three patients were diagnosed with ectasia patterns based on SS-OCT. All patients showed abnormalities in at least one Fourier index parameter for at least one eye at 3 or 6 mm, on keratometric, anterior, or posterior analyses. IVCM examination revealed changes in all corneal layers. Conclusions: By combining the results of multimodal im-aging, we were able to detect preclinical abnormalities, distinguish characteristic changes com-mon to ichthyosis, and reveal the depth and characteristics of corneal abnormalities. Therefore, patients with ichthyosis should be examined for DED and ectatic disorders early in clinical prac-tice.

This paper reports the effect of as-deposited surface condition on the fatigue strength in an additive manufactured titanium alloy Ti-6Al-4V (WAAM Ti64). First, local stress concentration caused by the surface waviness was quantified by a metrology technique followed by numerical modelling. Fatigue tests were conducted under bending load with the as-deposited surface being under tensile cyclic stress. The applicability of two predictive methods was studied and compared with the fatigue test results. The traditional notch stress method overestimated the fatigue strength by a factor of 1.5 at a given life; the poor agreement with the test is attributed to the crack propagation from the waviness being dominant in the bending test, i.e., the crack initiation stage was short, hence the local stress method is unsuitable. The fracture mechanics approach has delivered good predictions at every applied stress levels. The method treats a waviness trough as an initial crack. This approach is suitable for predicting the fatigue life in materials built by wire based directed energy deposition processes.