Arterial hypertension is a health problem that affects millions of people around the world. Particularly in Chile, according to the last health survey in 2019, 28.7% of the population had this condition, and arterial hypertension complications cause one in three deaths per year. In this work, we have used molecular simulation tools to evaluate new compounds designed in silico by our group as possible anti-hypertensive agents, taking Neutral Endopeptidase (NEP) as a target, a key enzyme in the arterial hypertension regulation at the level kidney. We use docking experiments, molecular dynamics simulation, free energy decomposition calculations (by MM-PBSA method), and ligand efficiency analysis to identify the best anti-hypertensive agent pharmacokinetic and toxicological predictions (ADME-Tox). The energetic components that contribute to the complexes stability are the electrostatic and Van der Waals components; however, when the ADME-Tox properties were analyzed, we conclude that the best anti-hypertensive candidate agents are Lig783 and Lig3444, taking Neutra Endopeptidase as a target.

This paper presents results from numerical and experimental investigation on Charpy tests in order to point out failure mechanisms and to evaluate new polymeric blends PP+PA6+EPDM. Charpy tests were done for initial velocity of the impactor of 0.96 m/s and its mass of 3.219 kg and these data were also introduced in the finite element model. The proposed model take into account the system of four balls, including support and the ring of fixing the three balls and it has a finer discretization of the impact area to highlight the mechanisms of failure and their development in time. The constitutive models for four materials (polypropylene with 1% Kritilen, two blends PP+PA6+EPDM and a blend PA6+EPDM) were derived from tensile tests. Running simulations for each constitutive model of material makes possible to differentiate the destruction mechanisms according to the material introduced in the simulation, including the initiation and the development of the crack(s), based on equivalent plastic strain at break (EPS) for each material. The validation of the model and the simulation results was done qualitatively, analysing the shape of broken surfaces and comparing them to SEM images and quantitatively by comparing the impact duration, energy absorbed by the sample, the value of maximum force during impact. The duration of the destruction of the specimen is longer than the actual one, explainable by the fact that the material model does not take into account the influence of the material deformation speed in Charpy test, the model being designed with the help of tests done at 0.016 m/s (1000 mm/min) (maximum strain rate for the tensile tests). Experimental results are encouraging for recommending the blends 20% PP+42% PA6+28% EPDM and 60% PA6+ 40%EPDM as materials for impact protection at low velocity (1m/s). Simulation results are closer to the experimental ones for the more brittle tested materials (with less content of PA6 and EPDM) and more distanced for the more ductile materials (with higher content of PA6 and EPDM).

The growth of solid particles during liquid phase sintering was modeled by the Cellular Automata method. The binary phase diagram and Fickian approach for the diffusion process were applied to simulate the chemical composition variation in liquid and solid phases during sintering. The Oswald-Ripening effect was considered during the dissolution of the solid phase in the liquid phase. It is used to define the probability of solid-phase dissolution by the liquid phase and develop the model to simulate the alloy with solid solubility. So, the microstructure could be modeled in the liquid phase sintering process.

Coronavirus disease 2019 (COVID-19) is an emerging infectious disease that was first reported in Wuhan, China and has subsequently spread worldwide. In the absence of any antiviral or immunomodulatory therapies, the disease is spreading at an alarming rate. 5 to 10% of recovered patients in Wuhan test positive again; this suggest that for controlling COVID-19, vaccines may be better option than drugs. A clinical trial to evaluate an anti-COVID-19 vaccine has started recently. However, its efficacy and potency have to be evaluated and validated. As an alternative, we are presenting a first-of-its-kind, designed multi-peptide subunit based epitope vaccine against COVID-19. The vaccine construct comprise an adjuvant, CTL, HTL, and B-cell epitopes joined by linkers. The vaccine is non-toxic, non-allergenic, thermostable and immunogenic with the capability to elicit a humoral and cell-mediated immune response. The findings are validated with high-end computation-based methods. This unique vaccine is made up of 33 highly antigenic epitopes from three proteins that have a prominent role in host receptor recognition, viral entry, and pathogenicity. We advocate this vaccine must be synthesized and tested urgently as public health priority.

In the presented paper, a comprehensive study will be done on shape factor analysis of MoS2-GO in H2O-C2H6O2 based hybrid nanoliquids associated with effect and influence of transverse magnetic field and thermal radiation. The effect of variation in different parameters and nanoliquids shapes under temperature and velocity distribution is explored and also non-linear thermal radiation will be analyzed. Algorithms are introduced in proportion to mathematical modeling based on their numerical results and comparative curves for further explanation. In addition, it will be done research for influence and effect of new significant parameters emerged to the model to do sensitivity analysis and also their output results are demonstrated, examined and compared together by presenting graphs and tables. Based on detailed discussions, authentication of attained results designates the high accuracy of applied methods deployed to solve presented model in the paper. Our results satisfy that our used approach is accurate, highly reliable and also effective. All mentioned steps will be described throughout the literature.

Curcumin is one of the bioactive metabolites of turmeric (Curcuma longa), known for its pleiotropic pharmacological actions, including antioxidant and anti-inflammation, anticholinesterase, immunomodulation, and neuroprotection. Substantial evidence suggests the therapeutic benefits of curcumin against neurodegenerative disorders, including Alzheimer’s disease (AD), acting on a diverse array of brain targets that make the molecular mechanisms complicated. System biology level-investigation could potentially present a comprehensive molecular mechanism to delineate the neuropharmacological action of curcumin. In this study, we used integrated system pharmacology and molecular simulation analysis to gain insights into the underlying mechanism of curcumin action against AD. Network pharmacology study identified curcumin-targeted potential cellular pathways such as phosphatidylinositol 3-kinase/protein kinase B (PI3K/Akt) signaling, neurotrophin signaling, toll-like receptor (TLR) signaling, and autophagy, and proteins such as tropomyosin receptor kinase B (TrkB), liver X-receptor-beta (LXR-β), estrogen receptor-β (ER-β), mammalian target of rapamycin (mTOR), TLR-2, N-methyl-D-acetate receptor subunit 2B (GluN2B), β-secretase and glycogen synthase kinase-3β (GSK-3β), which are intimately associated with neuronal growth and survival, immune response, and inflammation. Moreover, the molecular modeling further verified that curcumin showed a significant binding affinity to mTOR, TrkB, LXR-β, TLR-2, ER-β, GluN2B, β-secretase, and GSK-3β, which are the crucial regulators of molecular and cellular processes associated with AD. Together, the present system pharmacology and in silico findings demonstrate that curcumin might play a significant role in modulating AD-pathobiology, supporting its therapeutic application for the prevention and treatment of AD.

Precipitation downscaling is widely employed for enhancing the resolution and accuracy of precipitation products from general circulation models (GCMs). In this study, we propose a novel statistical downscaling method to foster GCMs’ precipitation prediction resolution and accuracy for monsoon region. We develop a deep neural network composed of convolution and Long Short Term Memory (LSTM) recurrent module to estimate precipitation based on well-resolved atmospheric dynamical fields. The proposed model is compared against GCM precipitation product and classical downscaling methods in the Xiangjiang River Basin in South China. Results show considerable improvement compared to the ECMWF-Interim reanalysis precipitation. Also, the model outperforms benchmark downscaling approaches, including 1) quantile mapping, 2) support vector machine, and 3) convolutional neural network. To test the robustness of the model and its applicability in practical forecast, we apply the trained network for precipitation prediction forced by retrospective forecasts from ECMWF model. Compared to ECMWF precipitation forecast, our model makes better use of the resolved dynamical field for more accurate precipitation prediction at lead time from 1 day up to 2 weeks. This superiority decreases along forecast lead time, as GCM’s skill in predicting atmospheric dynamics being diminished by the chaotic effect. At last, we build a distributed hydrological model and force it with different sources of precipitation inputs. Hydrological simulation forced with the neural network precipitation estimation shows significant advantage over simulation forced with the original ERA-Interim precipitation (with NSE value increases from 0.06 to 0.64), and the performance is just slightly worse than the observed precipitation forced simulation (NSE=0.82). This further proves the value of the proposed downscaling method, and suggests its potential for hydrological forecasts.

The increased consumption of food requiring thermoformed packaging means that the packaging industry demands customized solutions in terms of shapes and sizes to make the packaging unique. In particular, the food industry increasingly requires more transparent packaging, with greater clarity and a better presentation of the product features they contain. However, in turn, the differentiation of products is sought through the geometry and final finish of the product, as well as the arrangement of food inside the packaging. In addition, these types of packaging usually include ribs in the walls to improve physical properties, however they also affect the final aesthetics of the product. In accordance with this, this research study analyses by studying the mechanical properties of different relief geometries that can affect not only the aesthetics but also their strength. For this purpose, tensile and compression tests have been carried out. The results provide comparative data on the reliefs studied and show that there are different shapes, sizes and layout.

Turbulent flows over and within forest canopies have recently been modeled with success using Large Eddy Simulations (LES). Validation exercises against experimental data suggest that models can be applied with a high degree of confidence for many applications, mechanical and physiological plant/atmosphere interaction analysis, seed or pollen dispersal, wildfire spread and firebrand transport, or investigation of causes of eddy-covariance technique bias. Long distances required for shear-induced turbulence to equilibrate, result in the widespread use of cyclic boundary conditions in LES atmospheric boundary layer studies. Vegetation drag dissipates air momentum in the atmosphere, but equilibrium is often achieved through compensatory momentum source, supplied by macro-scale pressure gradient forcing. Unfortunately, both classical Ekman balance or simple spatially-constant pressure gradient techniques for implementing this forcing have major drawbacks in the context of cyclic boundary conditions for the applications listed above. Among them, it is difficult to specify aspects of the mean velocity profile such as a specific desired wind velocity and direction at a reference height. In the present paper, we propose a new technique for capturing the effects of a large-scale pressure gradient force (LSPGF) that can be used at stand scale and enables simulation of realistic and specifiable wind fields. Several variants of this LSPGF are developed and analyzed here and validated against experimental data. Although this LSPGF technique is developed in the context of HIGRAD/FIRETEC wildfire simulations, LSPGF can be used for any LES wind modeling application aimed at generating detailed stand-scale wind fields with resolved turbulence and shear profiles consistent with vegetation structure in the boundary layer.

Lightning strike can cause a considerable damage in aircraft parts made from semiconducting materials such as Carbon Fiber Reinforced Plastics (CFRPs). Therefore, in recent years, the lightning strike phenomenon has attracted the interest of the academic community and the aircraft industry. Until now, the problem has been addressed mainly experimentally, while the reported numerical works are very limited. In the present work, a coupled electro-thermal FE model has been developed using the ANSYS commercial FE code to simulate the lightning strike damage in unidirectional CFRP laminates due to the Joule heat flux phenomenon. The model is based on the SOLID69 thermoelectric element and applies a non-linear, time-transient analysis. The main input to the model is the thermal-electrical properties of the composite material which vary with temperature. Using the model, a parametric study on the effect of mesh density and peak intensity on the thermal damage has been performed. Three electrical lightning strikes of low (10 kA), medium (30 kA) and high peak intensity (40 kA) have been applied according to the SAE ARP 5412 standard. The electro-thermal model has been validated against a numerical model from the literature. The numerical results reveal that the increase of peak intensity leads to the increase of the area and penetration depth of matrix thermal damage (pyrolysis) as well as to the increase of the area of fiber damage (deterioration and ablation). Through progressive damage modeling, the residual tensile strength of the CFRP plate after being subjected to lightning strike of different peak intensity has been predicted. Lightning strike initial damage has been simulated by translating the thermal field into degradation of elastic properties of the lamina. The results show an increase in the accumulated matrix damage and a decrease of tensile strength due to the initial lightning strike damage. For the maximum peak intensity of 40 kA, a decrease in tensile strength of 4.8% has been predicted

Bimetallic nanoparticles are of interest since they lead to many interesting electrical, chemical, catalytic, and optical properties. They are particularly important in the field of catalysis since they show superior catalytic properties than their monometallic counterparts. The structures of bimetallic nanoparticles depend mainly on the synthesis conditions and the miscibility of the two components. In this work, PdPt alloyed-bimetallic nanoparticles (NPs) were synthesized through the polyol method, and characterized using spherical aberration (Cs) corrected scanning transmission electron microscopy (STEM). High-angle annular dark-field (HAADF)-STEM images of bimetallic nanoparticles were obtained. The contrast of images shows that nanoparticles have an alloy structure with an average size of 8.2 nm. Together with the characterization of nanoparticles, a systematic molecular dynamics simulations study, focused on the structural stability and atomic surface segregation trends in 923-atom PdPt alloyed-bimetallic NPs was carried out.

Current numerical methods for simulating biophysical processes in aquatic environments are typically constructed in a grid-based Eulerian framework or as an individual-based model in a particle-based Lagrangian framework. Often, the biogeochemical processes and physical (hydrodynamic) processes occur at different time and space scales, and changes in biological processes do not affect the hydrodynamic conditions. Therefore, it is possible to develop an alternative strategy to grid-based approaches for linking hydrodynamic and biogeochemical models that can significantly improve computational efficiency for this type of linked biophysical model. In this work, we utilize a new technique which links hydrodynamic effects and biological processes through a property-carrying particle model (PCPM) in a Lagrangian/Eulerian framework. The model is tested in idealized cases and its utility is demonstrated in a practical application to Sandusky Bay. Results show the integration of Lagrangian and Eulerian approaches allows for a natural coupling of mass transport (represented by particle movements and random walk) and biological processes in water columns which is described by a nutrient-phytoplankton-zooplankton-detritus (NPZD) biological model. This method is far more efficient than traditional tracer based Eulerian biophysical models for 3-D simulation, particularly for a large domain and/or ensemble simulations.

This paper describes a case study for applying of hybrid-electric propulsion system for a general aviation aircraft. The work was performed by a joint team of CIRA and the Department of Industrial Engineering of the University of Naples “Federico II”. Electric and hybrid electric propulsion for aircraft has gained widespread and significant attention over the past decade. The driver for industry interest has principally been the need to reduce emissions of combustion engine exhaust products and noise, but increasingly studies revealed potential for overall improvement in energy efficiency and mission flexibility of new aircraft types. The project goal was to demonstrate feasibility of aeronautic parallel hybrid-electric propulsion for a Light aircraft varying the mission profiles and the electric configuration. Through a creation, and application, of a global model, with software AMESim^®, in which it can be represented everything about the components chosen by the industrial partners, some interesting considerations are carried out. In particular, it was confirmed that with the only integration of state of the art technologies, for some particular missions, the advantages of aircraft hybrid-electric propulsion, for light aircraft, are notable.

During the recent decades, global warming by greenhouse gas evolution has attracted worldwide attention and evermore strict regulations thereon have become institutionalized as international policies. In the process, more environment-friendly power generation technologies have been developed utilizing fossil fuels with a view to timely commercialization. As one of such “clean coal” technology, Integrated Gasification Fuel Cell system is a promising power generation means and COS hydrolysis reactor is installed downstream of coal syngas to remove acidic gas constituents such as H2S and COS. The most significant design parameters affecting performance of the COS hydrolysis reactor were selected to be GHSV, (catalytic) reaction temperature, and length ratio and numerical modeling was performed considering heat and fluid flow transfer as well as chemical reaction kinetics. Effect of the selected design parameters on the variation of conversion rate and reactant gas mixture concentration were comprehensively investigated to predict performance of COS hydrolysis reactor. Stochastic modeling of reactor performance was finally performed using Monte Carlo simulation and linear regression fitting.

During speciation-with-gene-flow, a transition from single-locus to multi-locus processes can occur, as strong coupling of multiple loci creates a barrier to gene flow. Testing predictions about such transitions with empirical data requires building upon past theoretical work and the continued development of quantitative approaches. We simulated genomes under different evolutionary scenarios of gene flow and divergent selection, extending previous work with the additions of neutral sites and coupling statistics, allowing us to investigate if and how selected and neutral sites differ in the conditions they require for transitions during speciation. As the per-locus strength of selection grew and/or migration decreased, it became easier for selected sites to show divergence – and thus to rise in linkage disequilibrium (LD) with each other as a statistical consequence – farther in advance of the conditions under which neutral sites could diverge. Indeed, even very low rates of gene flow were sufficient to prevent differentiation at neutral sites. However, once strong enough, coupling among selected sites eventually reduced gene flow at neutral sites as well. To explore whether similar transitions might be detectable in empirical data, we used published genome resequencing data from three taxa of Heliconius butterflies. We found that allele-frequency outliers and F ST outliers exhibited stronger patterns of LD than the genomic background, as expected. The statistical characteristics of LD – likely indicative of the strength of coupling of barrier loci – varied between chromosomes and taxonomic comparisons. Broad qualitative agreement between the patterns we observed in the empirical data and our simulations suggests that selection drives rapid genome-wide transitions to multi-locus coupling, illustrating how divergence and gene flow interact along the speciation continuum.

Three-phase to single-phase matrix converter (TSMC) is used as the transmitter for transient electromagnetic method (TEM) instrument, instead of an AC-DC converter and an H-bridge inverter. The transmitter produces excitation current for primary field. The output current has a waveform with a bipolar square of half duty cycle, which is required by TEM. The space vector PWM based on input currents is discussed in detail. The control method of input power factor is proposed for TSMC. The simulation model of TSMC is established and the simulations of different conditions are completed. The simulation results show the controllability of the input power factor is illustrated.

Recent advances in sensor and platform technologies such as satellite systems, unmanned aerial vehicles (UAV), manned aerial platforms, and ground-based sensor networks have resulted in massive volumes of data is produced and collected about the earth. Processing, managing, and analyzing these data is one of the main challenges in 3D synthetic representation used in modeling and simulation (M&S) of the natural environment. M&S devices, such as flight simulators, traditionally require a variety of different databases to provide a synthetic representation of the world. M&S often requires integration of data from a variety of sources stored in different formats. Thus, for simulation of a complex synthetic environment, such as a 3D terrain model, tackling interoperability among its components (geospatial data, natural and man-made objects, dynamic and static models) is a critical challenge. Conventional approaches used local proprietary data models and formats. These approaches often lacked interoperability and created silos of content within the simulation community. Therefore, open geospatial standards are increasingly perceived as a means to promote interoperability and reusability for 3D M&S. In this paper, the Open Geospatial Consortium (OGC) CDB Standard is introduced. “CDB” originally refers to Common DataBase which is currently considered as a name with no abbreviation in the OGC community. The OGC CDB is an international standard for structuring, modeling, and storing geospatial information required in high performance modeling and simulation applications. CDB defines the core conceptual models, use cases, requirements, and specifications for employing geospatial data in 3D M&S. The main features of the OGC CDB Standard are described as run-time performance, full plug-and-play interoperable geospatial data store, usefulness in 3D and dynamic simulation environment, ability to integrate proprietary and open-source data formats. Furthermore, compatibility with the OGC standards baseline reduces the complexity of discovering, transforming, and streaming geospatial data into the synthetic environment and makes them more widely acceptable to major geospatial data/software producers. This paper includes an overview of OGC CDB version 1.0 which defines a conceptual model and file structure for the storage, access, and modification of a multi-resolution 3D synthetic environment data store. Finally, this paper presents a perspective of future versions of the OGC CDB and what the steps are for humanizing the OGC CDB standard with the other OGC/ISO standards baseline.

In this work, we examined the effect of tropospheric emissions on tropospheric ozone (O₃) by conducting three-dimensional (3D) chemistry transport model (CTM) simulations. For the control run, the CTM model simulates tropospheric O₃ levels with a complete set of anthropogenic, biomass burning, and vegetation emissions [8]. For the no-emission simulation, all anthropogenic, biomass burning, and vegetation emissions were turned off. Comparisons of results from these two simulations exhibit the emission impacts on the tropospheric O₃. In the no-emission simulation, distinctive low surface O₃ with concentrations less than 5 ppbv prevail over the Amazon basin, tropical South America, tropical South Africa, Southeast Asia. Transport of air from these land areas downwind contributes to the low O₃ over the remote marine boundary layer. In contrast, elevated O₃ levels over the extra-tropical remote marine boundary layer are less supported by the anthropogenic and biomass burning emissions but more sustained by the downward transport of O₃ from the stratosphere. These results demonstrate that the northern hemisphere continental areas (north of 30^◦N ), polar regions, and tropical continental regions are more sensitive to the tropospheric emissions. The northern hemisphere winter is mostly dominated by the stratospheric processes, while the tropospheric emissions dominate over the southern hemisphere tropical continental areas from tropics to 30^◦S latitudinal bands. The northern hemisphere continental regions are increasingly dominated by tropospheric emissions from spring, to reach maxima in summer, and started to reduce in autumn months.

The use of unmanned aerial vehicle (UAV) during emergency response of a disaster has been widespread in recent years and the terrain images captured by the cameras on board these vehicles are significant sources of information for such disaster monitoring operations. Thus, analyzing such images are important for assessing the terrain of interest during such emergency response operations. Further, these UAVs are mainly used in disaster monitoring systems for the automated deployment of sensor nodes in real time. Therefore, deploying and localizing the wireless sensor nodes optimally, only in the regions of interest that are identified by segmenting the images captured by UAVs, hold paramount significance thereby effecting their performance. In this paper, the highly effective nature-inspired Plant Growth Simulation Algorithm (PGSA) has been applied for the segmentation of such terrestrial images and also for the localization of the deployed sensor nodes. The problem is formulated as a multi-dimensional optimization problem and PGSA has been used to solve it. Furthermore, the proposed method has been compared to other existing evolutionary methods and simulation results show that PGSA gives better performance with respect to both speed and accuracy unlike other techniques in literature.

The purpose of this study is to analyze how global research cooperation patterns in the secondary battery industry have changed over recent years and to identify the evolution in the focus of research. To this end, network analysis was performed using the nationality information of the authors of a 10-year multinational joint research paper related to lithium-ion batteries. Furthermore, keyword analysis and topic modeling were performed using the abstract data from the study. The results of this study confirm that some countries that are not well-known in the field, such as Australia, Spain, and France, showed high centrality, compared with the level of cooperation scale. Additionally, six research topics were identified. According to a comparison over the first half of the decade, no difference was observed in the appearance of keywords indicating high energy density and conductivity with lithium, a key mineral. Keyword distribution was high for topics like battery charging and discharging in the first half of the decade, and for next-generation battery materials, such as solid electrolytes, lithium metal anodes, and lithium-sulfur batteries in the second. These results provide insights into the establishment of R&D cooperation strategies by countries and pre-planning by companies in the battery industry.

The study delved into the impact of two extrusion processing parameters—screw speed (SS at 400, 600, 800 RPM) and material moisture content in the extruder barrel (M at 12, 15, 18%) at constant feed rate (50 kg/h)—on reducing the content of alternariol (AOH), alternariol monomethyl ether (AME), tenuazonic acid (TeA), and tentoxin (TEN) in whole-grain red sorghum flour. Ultra-performance liquid chromatography coupled with a triple-quadrupole mass spectrometer (UPLC-MS/MS) was used for determination of Alternaria toxin levels. The extruder die temperature ranged between 136 and 177 °C, the pressure at the die was from 0.16 to 6.23 MPa, the specific mechanical energy ranged from 83.5 to 152.3 kWh/t, the torque ranged between 88 to 162.8 Nm, while the mean retention time of material in the barrel was between 5.6 and 13 s. Optimal parameters for reducing the concentration of all Alternaria toxins with the satisfactory quality of sorghum snacks were: SS=400 RPM, M= 12%, with a reduction of 61.4, 76.4, 12.1 and 50.8% for AOH, AME, TeA and TEN, respectively.

Adequate public spaces and urban green areas are key criteria for urban development and infrastructure implementation of healthy cities. Latterly, there has been an increasing number of research methods using artificial intelligence (AI) to monitor, quantify, and control the state of these spaces with an aim towards pioneering research in Urban Studies. However, in informal areas, open-data access tends to lack adequate and updated information, making it difficult to use AI methods. Hence, we propose a methodology for restricted open data collection and preparation for future use in machine learning or spatial data science models for similar areas. To that extent, we examine two peripheral and low-income neighborhoods in Quito, Ecuador, La Bota and Toctiuco, to analyze their public spaces, urban green areas, points of interest, and road networks, and how they address healthy cities criteria. We develop an original methodological approach that combines an index of proximity, accessibility, quantity, and quality of these spaces with geospatial and network analysis techniques. Results indicate that the connectivity and structure of these spaces are centralized and nodal, representing exclusion and segregation. This work provides insights on potential healthy spaces, and information to urban planners and policymakers in decision-making for healthy urban infrastructure.

The biomethane accumulation of several combinations of whey and sugarcane molasses, inoculated with sludge from a treatment facility of one of the dairy enterprises of Imbabura, was assessed in the current experiment at a concentration of 0.5 g/l COD. The whey: molasses (W: M) ratios for each treatment were 0:100, 25:75, 50:50, 75:25, and 100:0, with a constant temperature of 37°C and an initial pH adjustment of 7.5. Half a litre of total mixes was used for each treatment in duplicate. Six kinetic models were evaluated to account biomethane accumulation in anaerobic co-digestion processes in batch of whey and sugarcane molasses. Five of these have been tested by other researchers, and one was developed by modifying a first-order model to consider changes in the biomethane accumulation profile. This proposed model, along with the modified two-phase Gompertz model, resulted in the ones that were best able to adjust the experimental data, obtaining in all cases an R² ≥ 0.949, indicating the accuracy of both models. In addition, the proposed here model has five parameters, one less than the modified two-phase Gompertz model, making it more straightforward and robust.

The health of urban citizens is defined by how their living environments are planned, built, and operated. These complex relations between health and the characteristics of built environments require system-orientated thinking and transdisciplinary interventions, yet have mainly been addressed using conventionally narrow sector-based approaches. This paper investigates the opportunities and challenges of the Vietnamese Green Building Movement (GBM) based on a transdisciplinary approach, with attention to additional health benefits of green buildings that are currently under-researched, while highlighting building users’ perspectives. Focusing on the perspectives of high-rise building residents, the paper examines transdisciplinary insights collected from six thematic webinars, expert interviews, and, in particular, from a household survey conducted in Ho Chi Minh City, Vietnam. Among other findings on opportunities and challenges for the Vietnamese GBM, the paper points out a challenging mismatch between the high importance homebuyers place on green building health benefits, and the focus of GBM stakeholders on GB energy-saving benefits- which are not necessarily homebuyers’ most pressing concerns. With this evidence-based inquiry, the paper concludes that improved health and well-being should be considered co-benefits of green buildings, along with energy efficiency. Importantly, this paper also brings attention to the necessity of a systemic and transdisciplinary approach in both academic and practical efforts toward the implementation of SDG3- to “ensure healthy lives and promote wellbeing for all ages”- and SDG 11- “to make cities and human settlements inclusive, safe, resilient and sustainable”.

Although the Slicing Method (SM) is effective for calculating the volume of point cloud objects (PCOs), it is restricted in terms of applicability and practicability because of a certain contingency and directional defects. The Co-Opposite-Direction Slicing Method (CODSM) proposed in this paper is an improved method for calculating PCO volume by increasing parallel (co-opposite-direction) observation and considering the two-way mean as the result. This method takes full advantage of the mutual offsetting of random errors and the compensation of systematic directional errors, which can effectively overcome (or mitigate) the effect of random errors and reduce the effect of systematic errors in SM. In this paper, two typical objects, a cone model and a stone lion base, are the examples for calculating PCO volume using CODSM. The results show that CODSM has all the inherent advantages of SM and effectively weakens the volatility of random errors and the directionality of systematic errors from SM. Therefore, CODSM is a robust configuration upgrade of SM.

This paper addresses pastoral resilience by drawing out the coping strategies and mechanisms utilized by the Maasai Pastoralists through a food system approach, based on the study findings of an anthropological study of pastoralism in Laikipia County, Rift Valley, Kenya. This paper is guided by the specific objectives aimed at establishing actors and their roles, and describing the institutional settings and changes in pastoralism. Using a new institutionalism approach, the paper focuses not only on the actors and their roles in pastoralism but also on how internal and external forces regulate access and use of common pool resources (CPRs) resulting in sustainability of the food system. We argue that this has an impact on the practice of pastoralism that continually defines and redefine the actors’ roles as well as elicit the value of pastoral economies and benefits accrued to a wide range of actors hence reinforcing pastoral resilience. The study also identified institutional settings and changes that lead to pastoral survival resulting from the country’s devolved system of governance. Data collection was through in-depth interviews, key informant interviews, focus group discussions and unstructured observations in the pastoral regions. The findings reveal that actors at the household, state, non-state, and service providers have developed varied coping strategies and mechanisms that sustain pastoralism. The study also identified institutional settings and changes that promote pastoral resilience; notably, private land ownership patterns, co-management of livestock markets, commercialization of herding, decentralization of livestock services, holistic management of pasturelands and the use of water-shed management plans. As a result, increased scholarship and advocacy in regards to the concept of co-management of livestock markets, is recommended as a means of understanding pastoral resilience that the food system exhibits.

It is well known that that there is an intrinsic link between the financial and energy sectors, which can be analyzed through their spillover effects, which are measures of how the shocks to returns in different assets affect each other’s subsequent volatility in both spot and futures markets. Financial derivatives, which are not only highly representative of the underlying indices, but can also be traded on both the spot and futures markets, include Exchange Traded Funds (ETFs), a tradable spot index whose aim is to replicate the return of an underlying benchmark index. When ETF futures are not available to examine spillover effects, “generated regressors” are useful for constructing both Financial ETF futures and Energy ETF futures. The purpose of the paper is to investigate the co-volatility spillovers within and across the US energy and financial sectors in both spot and futures markets, by using “generated regressors” and a multivariate conditional volatility model, namely Diagonal BEKK. The daily data used are from 1998/12/23 to 2016/4/22. The data set is analyzed in its entirety, and are also subdivided into three distinct subsets. The empirical results show there is a significant relationship between the Financial ETF and Energy ETF in the spot and futures markets. Therefore, financial and energy ETFs are suitable for constructing a financial portfolio from an optimal risk management perspective, and also for dynamic hedging purposes.

The increasing adoption of student-centred learning environs by the institutions of higher education in business, has led to new mechanisms and methodologies such as the Simulation-Based Learning (SBL), Problem-Based Learning (PBL) and Challenge-Based Learning (CBL). Literature has shown evidence of raising interest in these methodologies towards a more experiential paradigm with regard to upcoming events from the surrounding real-world context. This paper presents a Systematic Bibliographic Literature Review (SBLR) with respect to the integration and application of these innovative and collaborative methodologies in higher education. It aimed to identify its relevant advantages, challenges, and consequences for the future of business education. Bibliographic databases were searched for documents published up to May 2024 to categorize key topics discussed in the literature on SBL, PBL and CBL. The review process identified 89 empirical and non-empirical papers on SBL, PBL and CBL, business related paperwork, which resulted from the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) method. PRISMA is a framework with evidence-based data designed to help authors perform a systematic literature review. Data analysis revealed diverse subthemes for those methodologies uses in business higher education institutions. The research questions “What are the advantages, challenges and implications of SBL, PBL and CBL altogether, in the training of business students?” guided the study. The central output of the research is the discovery of the varying uses of SBL, PBL and CBL overall, to cope with diverse demands arising within environmental context. Future research directions are suggested.

This paper focuses on determining the State of Charge (SOC) of lithium-ion batteries when operating and the influence the State of Health (SOH) has on SOC determination. The paper studies the effects of the discharge rate on the battery performance and how it modifies the evaluation of the SOC. The article also analyzes the effects of battery aging on the determination of SOC. The online determination of SOC in lithium-ion batteries uses the linear behavior of battery discharge and how the discharge rate modifies the battery voltage slope. The paper develops a simple algorithm that relates the SOC of the battery with the online battery voltage. The proposed measurement method uses a very short controlled discharge at a specific rate that avoids unexpected interferences with the current operation of the battery during charge or discharge. We conducted a simulation process to evaluate the evolution of the SOC in Li-ion batteries for different operating stages. Experimental tests validate the proposed methodology, showing a close agreement between theoretical values and experimental results with 98% accuracy. The paper also deals with the determination of the aging factor in lithium batteries as a critical parameter to calculate the SOC. The method determines the aging factor using specific simulation for this goal. The results are compared to values obtained in an experimental test within high agreement (>93%). The proposed model applies to almost any lithium battery and is validated for a wide range of Battery State of Health, up to 50%, within accurate prediction, higher than 90%.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

Progress in laser-driven proton acceleration requires increasing the proton maximum energy and laser-to-proton conversion efficiency, while reducing the divergence of the proton beam. However, achieving all these qualities simultaneously has proven challenging experimentally, the increase in beam energy often coming at the cost of beam quality. Numerical simulations suggest that coupling multi-PW laser pulses with ultrathin foils could offer a route for such simultaneous improvement. Yet experimental investigations have been limited by the scarcity of such lasers and the need for very stringent temporal contrast conditions to prevent premature target expansion before the pulse maximum. Here, combining the newly commissioned Apollon laser facility that delivers high-power ultrashort (∼24fs) pulses, with a double plasma mirror scheme to enhance its temporal contrast, we demonstrate the generation of up to 35 MeV protons with only 5 J of laser energy. This approach also achieves improved laser-to-proton energy conversion efficiency, reduced beam divergence, and optimized spatial beam profile. Therefore, despite the laser energy losses induced by the plasma mirror, the proton beams produced by this method are enhanced on all accounts compared to those obtained under standard conditions. Particle-in-cell simulations reveal that this improvement results from the intensified electrostatic field caused by a more compact hot-electron distribution.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

Earthquake-triggered landslides are one of the most significant hazards worldwide. These landslides, involving small or large volumes, can develop in debris flow or avalanche with high mobility and long-runout distance. The motion processes of this kind of landslide also quite complicated. This study reproduced the motion processes of two landslides using the LS-RAPID program. The Aso Bridge landslide occurred on April 16, 2016, with rapid and long-runout distance characteristics. The Kataragai landslide occurred on April 9, 2018, travelling with flow-like behavior. Through field investigations and laboratory experiments, features and mechanical parameters of these two landslides were obtained. In the LS-RAPID program, the pre-failure models and motion processes of these two landslides were established and reproduced. Results indicated that sliding speed and travelling morphology at different intervals were considered as two indicators to describe their motion process. However, while sliding speed of these two landslides have significant differences with sliding speeds of actual landslides, the final morphologies after failure were consistent with those observed in the field investigation.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

Data obtained by Direct Numerical Simulations (DNS) of pressure-driven turbulent channel flow are studied in the range 180 ≤ Reτ≤ 10,000. Reynolds number effects on the Mean Velocity Profile (MVP) and second order statistics are analyzed with a view of finding logarithmic behavior in the overlap region or even further from the wall, well in the boundary layer’s outer region. Values of Kármán constant for the MVPs and the Townsend-Perry constants for the streamwise and spanwise fluctuation variances are determined for the Reynolds numbers considered. A data-driven model of the MVP, proposed and validated for zero pressure gradient flow over a flat plate, is employed for pressure-driven channel flow by appropriately adjusting Coles’ strength of the wake function parameter, Π. There is excellent agreement between the analytic model predictions of MVP and the DNS-computed MVP as well as of the Reynolds shear stress profile. The skin friction coefficient Cf is calculated analytically. The agreement between the analytical model predictions and the DNS-based computed discrete values of Cf is excellent.

Purpose: this paper evaluates the effect of thermo-formed aligners with complementary biomechanical attachments (CBA) on periodontal ligaments (PDL) during the expansion process of the maxillary arch using simulations based on the finite element method (FEM). Methods: four types of teeth (canine 3, premolar 4, premolar 5 and molar 6) were modeled using 3D CAD. In addition, aligners, CBAs and PDL were also 3D modeled. With this information, a FEM model was generated, and a clinical rehabilitation scenario was simulated. For the validation of the results, a comparison with medical records was performed. Results: for canine 3, the displacement was 0.134 mm with a maximum stress of 4.822 x10-3MPa in the amelocemental junction. For premolar 4, the displacement was 0.132 mm at a maximum stress of 3.273x10-3MPa in the amelocemental junction. Premolar 5 had a displacement of 0.129 mm and a stress of 1.358 x10-3MPa at 1 mm from the amelocemental junction. Molar 6 had a displacement of 0.124 mm and a maximum stress of 2.440 x10-3MPa. Conclusions: The simulations showed that the use of CBA reduces tooth tipping. The model with Vestibular CBA presented the best results in terms of the dental movement of expansion of the maxillary arch with the use of thermoformed aligners. Significance: Considering the difficulty of performing in vivo tests that evaluate the configuration effectiveness of the different CBA alternatives in thermoformed aligners, FEM techniques were used to reduce time and costs, and get accurate results with minimal errors.

Industrial Control Systems (ICS) are integral to managing and optimizing processes in various industries, including manufacturing, power generation, and more. However, the scarcity of widely adopted ICS datasets hampers research efforts in areas like optimization and security. This scarcity arises due to the substantial cost and technical expertise required to create physical ICS environments. In response to these challenges, this paper presents a groundbreaking approach to generating synthetic ICS data through a data-driven ICS network simulation. We circumvent the need for expensive hardware by recreating the entire ICS environment in software. Moreover, rather than manually replicating the control logic of ICS components, we leverage existing data to autonomously generate control logic. The core of our method involves the stochastic setting of setpoints, which introduces randomness into the generated data. Setpoints serve as target values for controlling the operation of the ICS process. This approach enables us to augment existing ICS datasets and cater to the data requirements of machine learning-based ICS intrusion detection systems and other data-driven applications. Our simulated ICS environment employs virtualized containers to mimic the behavior of real-world PLCs and SCADA systems, while control logic is deduced from publicly available ICS datasets. Setpoints are generated probabilistically to ensure data diversity. Experimental results validate the fidelity of our synthetic data, emphasizing its ability to closely replicate temporal and statistical characteristics of real-world ICS networks. In conclusion, this innovative data-driven ICS network simulation offers a cost-effective and scalable solution for generating synthetic ICS data. It empowers researchers in the field of ICS optimization and security with diverse, realistic datasets, furthering advancements in this critical domain. Future work may involve refining the simulation model and exploring additional applications for synthetic ICS data.

An algorithm is presented for a micro-model of a mining dump truck movement, which allows determining the optimal speed and acceleration of a vehicle, considering the change of the road grade. The structure of the simulation macro-model of an excavator-and-dump truck complex has been developed. The procedure for integrating a micro-model of a dump truck movement into a simulation model is shown. As a result of a series of experiments with a macro-model, the influence of open pit roads grade on the performance and efficiency of excavator-and-dump truck complexes was established. The necessity of considering in simulation excavator-and-dump truck complexes the speed regulation of dump trucks depending on the change in road grade is shown.

The continuous casting tundish is non-isothermal due to heat losses and temperature variation from the inlet stream generating relevant convection forces. This condition is commonly avoided through qualitative fluid dynamic analysis only. This work searches to establish the conditions for which non-isothermal simulations are mandatory or for which isothermal simulations are enough to accurately describe the fluid dynamics inside the tundish by quantifying the buoyant and inertial forces. The mathematical model, simulated by CFD software, considers the Navier-Stokes equations, the realizable k- model for solving the turbulence, and the Lagrangian discrete face to track the inclusion trajectories. The results show that temperature does not significantly impact the volume fraction percentages or the mean residence time results, nevertheless, bigger velocity magnitudes under non-isothermal conditions than in isothermal conditions and noticeable changes in the fluid dynamics between isothermal and non-isothermal cases in all the zones where buoyancy force dominates over inertial forces were observed. Because of the results, it is concluded that isothermal simulations can accurately describe the flow behavior in tundishes when the flow control devices control the fluid dynamic, but the simulation without control devices or with a weak fluid dynamic dependence on the control devices requires non-isothermal simulations.

Thermostatically controlled loads have great potential to make a significant contribution to improving energy efficiency in the building sector, which is responsible for 40% of greenhouse gas emissions in the EU. This, in addition to the environmental damage, represents a huge expense in the electricity bill. Therefore, it is very important to train engineers on how to design energy management systems for TCLs. With this goal in mind, it would be very useful to have a simulation-based educational tool (SBET) to understand thermostatically controlled loads, their characteristics and possibilities in energy efficiency. In addition, it would be very useful if this tool could be introduced in engineering curricula to help students to be better trained and enter the labor market with more opportunities. Based on the shortcomings detected, this work develops a SBET specifically designed to teach about TCLs (SBET-TCLs), both about their intrinsic characteristics and their better management. To verify the developed SBET-TCL, it has been tested in a real scenario: A survey was carried out among the students of the subject 'Alternative Energy Sources' of the degrees of Industrial Engineering. The results show that the use of SBET-TCL has very positive effects on the learning process.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

In this paper we investigate in different scenarios the feasibility of using massive multiple-input multiple-output (mMIMO) with Reconfigurable Intelligent Surfaces (RISs) to boost the throughput and coverage performances with high energy efficiency, considering sub-6 GHz, mmWave and THz bands. With that objective, a centralized radio access network (C-RAN) suitable for beyond fifth generation (B5G) systems is considered, where we integrate the base stations (BSs) with multiple RISs and devices or user equipment. RISs with a large number of quasi-passive reflecting elements constitute a low-cost approach capable of shaping the radio wave propagation and improve wireless connectivity. We consider a scenario where multiple RISs are combined with mMIMO in the uplink in order to provide connectivity to Smart City (thousands of active low power devices) wirelessly, in the 3.6GHz and 28GHz bands. We also address a scenario where RISs are adopted with mMIMO in the downlink so as to offer connectivity to a Stadium with Pitch, (thousands of active user equipment) in the 28GHz band. Finally, we have also studied the connectivity at 100GHz of a Factory where several RIS panels replacing most of the BSs equipped with mMIMO assure improved throughput and coverage. We concluded that RISs are capable of improving the performance in any of these analyzed scenarios at the different frequency bands, justifying that they are a key enabling technology for 6G.

In this paper, we propose a method for the generation of simulation test scenarios for autonomous driving. Based on the requirements of standard regulatory test scenarios, we can generate virtual simulation scenarios and functional scenario libraries for autonomous driving, which can be used for simulation verification of different ADAS functions. Firstly, the design operation domain (ODD) of the functional scenario is selected and the weight values of the ODD elements taken are calculated; then a combination test algorithm based on parameter weights is improved to generate autonomous driving virtual simulation test cases for the ODD elements, which can effectively reduce the number of generated test cases compared with the traditional combination test algorithm; then the traffic participant elements under each test case are Then, the values of the subelements under the traffic participant element in each test case are sampled and clustered to obtain hazard specific scenarios. Finally, the specific scenarios are applied to the automatic emergency braking (AEB) system on the model-in-the-loop (MIL) testbed to verify the effectiveness of this scenario generation method.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double <100> and <111> fiber and a unique component of (001)<110>, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

Experimental methodologies for fatigue lifetime prediction are time-intensive and susceptible to environmental variables. While the cohesive zone model is popular for predicting adhesive fatigue lifetime, entropy-based methods have also shown promise. This study aims to provide an understanding of the durability characteristics of CFRP adhesive joints by incorporating an entropy damage model within the context of the finite element method (FEM), examined the effects of different adhesive layer thicknesses on SLS models. As the adhesive layer increased in thickness, DAMAGE VARIABLES initially rose and then declined, peaking at 0.3mm. This finding provides crucial understanding into the stress behavior at the resin-CFRP interface and the resin's fatigue mechanisms.

This research delves into the impact of complex low-speed wake flow structures on the aerodynamic characteristics of objects downstream. It employs the proper orthogonal decomposition (POD) method and the domain precursor simulation method to compare traditional methods and validate this approach. The study generates several flow structures of parallel dual-cylinder wakes with different scales and spacing. The variations in the aerodynamic coefficient of three downstream objects at various times passing through wakes of varying scales are appropriately compared and analyzed. The study establishes that the wake with a cylinder spacing of G=1.5 has a more compact and concentrated modal structure than that with a cylinder spacing of G=0.35. Smaller objects are more responsive to the wake flow structure with a spacing of G=1.5, whereas larger objects respond more to the flow structure with a spacing of G=0.35. The achieved results also reveal that the aerodynamic force coefficients of objects passing through the wakefield at different times are closely related to the temporal characteristics of the wake flow structure with different scales.

For enhancing the efficiency of cantilever casting the construction in the bridge, a novel rhombus traveling track of hanging basket was developed and optimized. The civil software titled Midas was applied to analyse the mechanical properties of the hanging basket with full load and control load. The strength and distortion of the walking mechanism were within the specified range when the maximum beam unit internal force of 149.69Mpa, which was less than the allowable stress of steel 175Mpa, and the anti-overturning safety factor of the hanging basket was 2.5 to meet the requirements. Through the comparative analysis of the key components and the finite element calculation, it was found that there was about 30% redundancy in the structure performance. Therefore, further optimization of each structure was carried out, and the front elevation of the main truss of 20° was achieved. It obtained the best performance in all aspects.

The objective of this study is to investigate the use of excavation behavior prediction and analysis software in the field of civil en-gineering. PLAXIS and SoilWorks, widely used in the engineering and academic communities, were employed as research tools for analyzing gravel layers and deriving appropriate ranges of soil elastic modulus for different software programs. By collecting excavation cases in the Xindian area of New Taipei City, Taiwan, and conducting deep excavation analysis using the displacement of retaining walls, this study provides recommended ranges for localized selection of soil elastic modulus. The suggested range for PLAXIS is 7,840 N/m² to 9,800 N/m², while Soil-Works suggests a range of 2,450 N/m² to 3,430 N/m². These ranges allow for reasonable estimation of maximum deformations during the final excavation stage. Based on the research findings, it is recommended that engineers refer to the provided ranges when selecting soil elastic modulus for excavation analysis in gravel layers using different soft-ware programs in the Xindian area of Taiwan to improve the accuracy of deformation predictions during the final excavation stage. These results serve as important references for engineers and contribute to the effective prediction and management of excavation behavior in civil engineering projects.

Our aim is to provide an insight of the procedures and the dynamics that lead the spread of contagious diseases through populations. Our simulation tool can increase our understanding on the spatial parameters which affect the diffusion of a virus. SIR models are based on the hypothesis that populations are “well mixed”. Our model constitutes an attempt to focus on the effects of the specific distribution of the initially infected individuals through the population and provide insights, considering the stochasticity of the transmission process. For this purpose, we represent the population using a square lattice of nodes. Each node represents an individual that may or may not carry the virus. Nodes that carry the virus can only transfer it to susceptible neighboring nodes. This important revision of the common SIR model provides a very realistic property: the same number of initially infected individuals can lead to multiple paths, depending on their initial distribution in the lattice. This property creates better predictions and probable scenarios to construct a probability function and appropriate confidence intervals. Finally, this structure permits realistic visualizations of the results to understand the procedure of contagion and spread of a disease and the effects of any measures applied.

Creep is a fundamental property naturally exists in some types of rock, which is significant for the long-term stability of roadways during the mining process. In this paper, the long-term strength of coal and rock were obtained via laboratory experiments, and a Cvisc elasto-viscoplastic model was adopted and introduced in FLAC3D, based on the 3101 transport roadway in Hongqinghe Coal Mine, to investigate the influence of creep on the stability of deep-high stress roadway. The test results show that the long-term strength of 3-1 coal and sandy mudstone, respectively, is 18.65 MPa, 39.95 MPa. The plastic zone, the deformation, and the damage of roadway surrounding rock behave an obvious increase after being excavated for 720d as the creep model was chosen. The plastic zone failure with models shear-p (1090.7 m3), shear-n (381.7 m3), tension-n (98.4 m3), and tension-p (30.8 m3), the damage value has an obvious increment of increased 21.2% (0.053), the deformation increases in the order is two-sidewalls (1978 mm), roof (907 mm), floor (101 mm). The creep of the roadway can be divided into three stages: the accelerating stage, the decaying stage, and the stable stage. The creep speed of each stage is greatly affected by the presence or absence of anchor spray support: the creep speed of the bare roadway roof, roadway side, and floor stability, respectively, is 1.01, 1.02, and 0.12 mm/d; After anchor spray support, the creep velocity, correspondingly, decreased to 0.69, 0.37, and 0.12 mm/d, and the amount of surrounding rock damage decreased from 0.302 to 0.243. This indicates that the anchor spray support can significantly reduce the creep effect of the roadway. The Cvisc creep model was verified reliable and can provide guidance for deep high-stress coal roadway support.

Microgrid is one of the important ways to accommodate distributed PV generation. However, the optimal planning scheme of microgrids is closely related to solar resources, load characteristics, and the key components of microgrid systems. This paper uses HOMER software to conduct collaborative planning for grid-connected PV-storage microgrids with electric vehicles in multiple scenarios. Specifically, we construct a multi-scenario capacity optimization model for PV generation, energy storage, and converters, considering both the cleanliness and economic performance of microgrids. The performance is quantified using indices such as net present cost, levelized cost of electricity, and carbon dioxide emission under multiple scenarios. Finally, we conduct extensive case studies on a business park in Wuhan, China, to compare and discuss the planning performance under multiple scenarios, as well as sensitivity analysis with specific cases.

The stability of the filling roof as an important bearing unit in the stope of the access stope in the filling mining method is of great significance to guarantee the safe and efficient production of the mine. Arrangement of mining approach in downward cemented filling stope is the key factor af-fecting stability of filling body roof. Based on combination of laboratory test, theoretical analysis and numerical simulation, the influence of different mining approach arrangement on stability of filling body roof is analyzed. The weak filling surface is formed between adjacent mining paths. The mechanical strength of the weak filling surface is significantly reduced by laboratory experiments. The relationship between distribution of the weak filling surface, azimuth angle and stability of filling roof is further studied by numerical simulation. The results show that the stability of the filler roof is the best when the upper and lower stratified mining approach is arranged vertically.

In order to study the effect of TiB2 particles on the mechanical properties of TiB2/6061Al composites, a series of TiB2/6061Al 3D representative volume element (RVE) were established based on SEM photos. This model took into account the ductile damage of the matrix and the traction separation behavior of the interface, and the linear damage evolution law was introduced to characterize the stiffness degradation behavior of the matrix elements. The mixed boundary conditions were used for RVE tensile experiments, and the accuracy of the predicted result was verified by the agreement of the experimental stress-strain curve. Results show that the addition of TiB2 particles can effectively promote the load-bearing capacity of the composite, but elongation is reduced. With the weight fraction of TiB2 increasing from 2.5% to 12.5%, the elastic modulus, yield strength, and tensile strength are increased by 8%, 10.37%, and 11.55% respectively, while the elongation decreased by 10%. The clustering rate of the TiB2 particles is also an important factor affecting the toughness of the composites. With the increase in the clustering rate of TiB2 particles from 20% to 80%, the load-bearing capacity of the composites is not improved, and the elongation of the composites is reduced by 8%. Moreover, the high strain region provides a fast expansion path for crack propagation and the particle spacing is a crucial factor that affects the stress field.

The current work investigates the auxetic tensile deformation behavior of the inversehoneycomb structure with 5 × 5 cells made of biodegradable poly(butylene adipate-coterephthalate) (PBAT). Fused deposition modeling, an additive manufacturing method, produced such specimens. Residual stress (RS) and warpage, more or less, always exist in such specimens due to layer-by-layer fabrication, i.e., repeated heating and cooling. The RS influences the auxetic deformation behavior, but its measurement is challenging due to the very fine structure. Instead, the finite-element(FE)-based process simulation realized by an ABAQUS plug-in numerically predicts the RS and warpage. The predicted warpage shows a negligible slight deviation compared to the design topology. This process simulation also delivers the temperature evolution of a small volume material, revealing the local cyclic heating and cooling. The achieved RS serves as the initial condition for the FE model used to investigate the auxetic tensile behavior. With the outcomes from FE calculation without considering RS at hand, the effect of the RS on the deformation behavior is discussed for the global force-displacement curve, the structural Poisson’s ratio evolution, the deformed structural status, the stress distribution, and evolution, where the first three and the warpage are also compared with experimental results. Furthermore, the FE simulation can easily provide the global stress-strain flow curve with the total stress calculated from the elemental ones.

Flood events are becoming more severe, causing significant problems to human communities, including physical, psychological, and material damage. For both flood forecasting in emergency response situations and flood mapping, georeferencing and data curation are paramount in the context of prevention or preparedness. Hence, data display, data management, and articulation with numerical simulation results must occur on GIS platforms. Our research is motivated by recent advances in Web and GIS technologies, social sensing and high-performance computing, and an envisaged wider availability of remote sensing data. This paper presents and discusses an innovative Web GIS platform named "RiverCure Portal" or "RCP" for short. This platform combines observations and hydrodynamic modelling tools to support various stages of the flood risk management cycle, including operational response, emergency preparedness, and risk assessment. RCP is a multi-organisation, multi-context digital platform with flexible configuration features to define and support multiple sensor types and modelling options, satisfying the various needs of different organisations and stakeholders. In addition, this paper discusses the RiverCure Approach, which encompasses the following tasks directly supported by the RCP platform: defining the context and involved geometries, associating sensors to the context, pre-processing and generating the context mesh, defining the simulation event, running the simulation event, and analysing the results from the simulation event. Thus, the RCP streamlines and simplifies data analysis and simulation procedures to meet decision-makers' needs. The novelties discussed in this paper include the design and discussion of a Web GIS platform that allows (i) to manage flood data and results of simulations at several contextual levels by different stakeholders such as domain experts, decision-makers, researchers, or students; (ii) to process and curate sensed data obtained from physical and social sensors; and (iii) update the state and values of the parameters of simulation tools through continuous data assimilation techniques for forecasting purposes. Finally, this paper supports the explanation and discussion with a running example, "Águeda 2016 flood" event, which dataset is publicly available for further study and experimentation.

The problem of optimal scheduling in a system with parallel queues and a single server has been extensively studied in the queueing theory. However, such systems have mostly been studied by assuming homogeneous attributes of arrival and service processes, or in heterogeneous case a Markov random process was usually assumed. In this paper, we explore the possibility of combining simulation and neural network paradigms for optimal scheduling in a heterogeneous system with an arbitrary inter-arrival and service time distributions. The service of any queue by the server is exhaustive. Further routing of the server after the queue has been emptied is as instructed by the trained neural network. Any change in the queue that currently has a server is accompanied by a switching cost. The simulated annealing optimization algorithm which is used to optimize the parameters of the neural network was adapted for numerically evaluated average cost function. A Markov decision problem was formulated for the corresponding markovian queueing system to verify the results of solving the optimization problem. In addition to comparing the actual values of the average cost, the parameter values of the neural network trained on the optimal control policy of the Markov model are also used to determine the domains of parameters required for the simulated annealing defined on a finite discrete domain. Numerical analysis shows the effectiveness of this approach. Moreover, a comparison of the results for different distributions illustrates the insensitivity of the optimal control policy to the shape of the distributions for the same two first moments. Thus, the optimal control policy for an exponential model can be used as a suboptimal one for the general system.

Abstract: The purpose of this study is to explore, from the perspective of government interven-tion, behavioral logic and game relationship among farmers, service organizations and the gov-ernment in the pest and disease control outsourcing system, as well as the endogenous motiva-tion of each subject. The results indicate that the stronger the willingness of each subject, the faster the stable state of joint pest and disease control among the three parties can be formed; In the case of implementing a single policy tool, the convergence rate of each party that imple-ments the regulatory policy alone is fast but may be unstable, while the rate is slow but more stable when a guidance- or incentive-based policy is solely applied; The effect of policy tool combination is much better than that of a single policy tool applied. The simultaneous imple-mentation of the three types of policy tools can form a policy system with both positive and negative mechanisms, which can maximize complementary and superposition effect.

In this paper, we present the investigation results of radiation-induced effects in metal-oxide-semiconductor (MOS) doped with moderate amounts of Zinc Oxide (ZnO) as a potential candidate for space-borne application. The samples were fabricated via the sputtering method at a working pressure of 3mTorr and a deposition temperature of 300oC. The ZnO samples were exposed to 1.25-MeV gamma-ray utilizing Co60 source, and their electronic response was measured at ionizing doses ranging from 10 kGy to 300 kGy. A comparative work was performed through finite element method to simulate the electronic response of the PN junction diode due to ionizing radiation. The results indicate that the ideality factor of the MOS diode increases as the ionizing dose increases, rendering it unsuitable for use as a diode. The degradation of the electrical parameters was also simulated, showing the increase in hole concentration. These findings suggest that the ejection of electrons occurred, which agrees with the gamma radiation effects trend. Furthermore, as the intensity of radiation increases, the spatial charge that arises from the separation of hole-electron pairs results in a substantial reduction of the electric field in the central portion of the n-type region. These findings provide insights into the degradation of electrical parameters in MOS devices under gamma radiation and have implications for their use in space-borne applications.

With the aim to improve cladding coating quality and prevent cracking, this paper established an extreme high-speed laser cladding thermo-mechanical coupling simulation model to study the evolution of the temperature field and residual stress distribution. Process parameters that impacted the macroscopic morphology of single-pass coatings were investigated. Numerical calculations and temperature field simulations were performed based on the process parameter data to validate the effect of the temperature gradient and cooling rate on the coating structure and the residual stress distribution. The results showed that a good coating quality could be achieved using a laser power of 2400 W, a cladding rate of 20 m/min, and a powder feeding rate of 20.32 g/min. The coatings’ cross-sectional morphology corresponded well with the temperature distribution predicted by numerical modeling of the melt pool. The microstructure of the molten coatings is affected by the temperature gradient and cooling rate, which vary greatly from the bottom to the middle to the top. Maximum residual stress appears between the bonding region of the coatings and the substrate, and the coatings themselves have significant residual stress in the form of tensile strains that are mostly distributed in the direction of the laser cladding speed.

Different inlet structures have a significant impact on the internal flow characteristics of a solid-magnesium powder water ramjet engine. Based on the magnesium-water reaction model, a computational fluid dynamics (CFD) method is applied to establish a numerical simulation method for the internal flow field of the engine, and the internal flow characteristics of the engine under different inlet structure conditions are studied. The simulation results show that high-temperature gas can effectively promote the ignition of magnesium powder at the top of the combustion chamber, while accelerating the evaporation of the first inlet water and increasing the combustion rate of magnesium powder. The secondary inlet has the most significant effect on the temperature inside the combustion chamber. When the secondary inlet flow rate increases towards the top of the combustion chamber, it increases the amount of heat absorbed by the evaporating water at the top of the chamber, thereby reducing the temperature at the top of the combustion chamber. However, when the flow rate is low, it results in insufficient oxidizer at the top of the combustion chamber, which is unfavorable for the combustion of magnesium powder.

The concerning rise in emergence and prevalence of resistant strains to drugs of M. tuberculosis has ,the prompted researchers to look for new and effective treatments. With this motive, biscoumarins were identified as the lead molecules on a whole-cell-based screening of several less explored low molecular weight bioactive compounds against M. tuberculosis strains. Among the screened biscoumarins, the highest dock score derivatives were synthesized (a-h) using a programmable microwave synthesizer for better yields and reaction control. The synthesized derivatives were evaluated against H37Rv, H37Ra, M. smegmatis, an MDR surrogate model, and other bacterial strains for the structure-activity response. Assessment of the synthesized library against mycobacterial strains led to the identification of compounds (f and d) as lead anti-tuberculosis agents. Compounds (f and d) exhibited less toxicity against human cell lines. At the same time, it displayed enjoyable activity wherein MIC concentrations were observed to be 16- and 32 µg/mL against the susceptible H37Rv, and H37Ra strains of M. tuberculosis and MIC value of 128 µg/mL for M. smegmatis, respectively. For mechanistic insights and identification of drug binding targets, molecular docking and dynamic simulations were employed for a panel of 16 mycobacterial enzymes essential for mycobacterial growth and survival. These in silico studies revealed the DprE1 enzyme as a druggable target for the anti-tuberculosis activity of the selected biscoumarins derivatives. Further investigation is underway in our laboratory, leading to its development as an anti-tuberculosis drug (animal model studies).

The monkeypox virus (MPXV) has become a major threat due to the increasing global caseload and the ongoing multi-country outbreak in non-endemic territories. Due to limited research in this avenue and the lack of intervention strategies, the present study was aimed to virtually screen bioactive phytochemicals against envelope proteins of MPXV via rigorous computational approaches. Molecular docking and molecular dynamic (MD) simulations were used to investigate the binding affinity of 12 phytochemicals against three envelope proteins of MPXV, viz., D13, A26, and H3. Silibinin, oleanolic acid, and ursolic acid were computationally identified as potential phytochemicals that showed strong binding affinity towards all the tested structural proteins of MPXV through molecular docking. The stability of the docked complexes was also confirmed by MD simulations. ADME analysis also computationally confirmed the drug-like properties of the phytochemicals, thereby asserting their suitability for consumption. Hence, this study envisions the candidature of bioactive phytochemicals as promising inhibitors against the MPXV, serving as template molecules that could further be experimentally evaluated for their efficacy against monkeypox.

This paper presents a novel theoretical and computational methodology for the generation of an onset turbulent field with prescribed properties in the numerical simulation of an arbitrary viscous flow. The methodology is based on the definition of a suitable distribution of volume force terms in the right–hand side of the Navier–Stokes equations. The distribution is represented by harmonic functions that are randomly variable in time and space. The intensity of the distribution is controlled by a simple PID strategy in order to obtain that the generated turbulent flow matches a prescribed turbulence intensity. A further condition is that a homogeneous isotropic flow is es- tablished downstream of the region where volume force terms are imposed. Although it is general, the proposed methodology is primarily intended for the computational modelling of hydrokinetic turbines in turbulent flows representative of tidal or riverine installations. A first numerical applica- tion is presented by considering the injection of homogeneous and isotropic turbulence with 16% intensity into a uniform unbounded flow. The analysis of statistical properties as auto-correlation, power spectral density, probability density functions, demonstrates that the generated flow tends to achieve satisfactory levels of stationarity and isotropy, whereas the simple control strategy used determines overestimated turbulent intensity levels.

Zika virus (ZIKV) has been characterized as one of the potential pathogens and placed under future epidemic outbreaks by the WHO. However, lack of potential therapeutics can result in uncontrolled pandemic like other human pandemic viruses; therefore, prioritized effective therapeutics development has been recommended against ZIKV. In this context, the present study adopted the strategy to explore the lead compounds from Azadirachta indica against ZIKV via concurrent inhibition of the ZIKVpro and ZIKVRdRp proteins using molecular simulations. Initially, structure-based virtual screening of 44 bioflavonoids reported in Azadirachta indica against the crystal structures of targeted ZIKV proteins resulted in the identification of top four common bioflavonoids, viz. rutin, nicotiflorin, isoquercitrin, and hyperoside. These compounds showed substantial docking energy (-7.9 to -11.01 kcal/mol) and intermolecular interactions with essential residues of ZIKVpro (His51, Asp74, and Ser135) and ZIKVRdRp (Asp540, Ile799, and Asp665) by comparison to the reference compounds, O7N inhibitor (ZIKVpro) and Sofosbuvir inhibitor (ZIKVRdRp). Long interval molecular dynamics simulation (500 ns) on the selected docked poses reveals the stability of respective docked complexes contributed by intermolecular hydrogen bonds and hydrophobic interactions. The predicted complex stability was further supported by calculated end-point binding free energy using molecular mechanics generalized born surface area (MM/GBSA) method. Consequently, the identified common bioflavonoids are recommended as promising therapeutic inhibitors of ZIKVpro and ZIKVRdRp for further experimental assessment.

Due to production space and operating environment requirements, mine production equipment often breaks down, which seriously affects the mine’s production schedule. To ensure the smooth completion of the haulage operation plan under abnormal conditions, a model of the haulage equipment rescheduling plan based on the random simulation of equipment breakdowns is established in this paper. The model aims to accomplish both the maximum completion rate of the original mining plan and the minimum fluctuation of the ore grade during the rescheduling period. This model is optimized by improving the wolf colony algorithm and changing the location update formula of the individuals in the wolf colony. Then, the optimal model solution can be used to optimize the rescheduling of the haulage plan by considering equipment breakdowns. The application of the proposed method in an underground mine revealed that the completion rate of the mine’s daily mining plan reached 83.40% without increasing the number of the equipment, while and the ore quality was stable. Moreover, the improved optimization algorithm converged fast and was characterized by high robustness.

A long-term forecast study on the electricity demand of Taoussa of Mali is conducted in this paper, with various scenarios of socioeconomic and technological conditions. The analysis tool, which is applied in scenarios simulation, is the Model for Analysis of Energy Demand from the International Atomic Energy Agency. The analysis results are annual electricity demand and peak load forecast for the electrification from the period 2020 to 2035. During the planning period, the analysis results show that the electricity demand will increase to 49.40 MW (332.57 GWh) for the low scenario (LS), 66.46 MW (472.61 GWh) for the reference scenario (RS), and 89.47 MW (635 GWh) for the high scenario (HS). In addition, the total electricity demand increased at an average rate of 8.13% in the LS, 10.31% in the RS and 12.56% in the HS in all sectors. The electricity peak demand is expected to grow at 7.92%, 10.53% and 12.91% corresponding to the three scenarios; in this case, the system peak demand in 2035 will increase to 64.88 MW for the LS, 92.2 MW for the RS and 126.22 MW, the days of peak load are between 17th -23rd in May. The Industry sector will be the biggest electricity consumer of Taoussa area.

Volcanism powered by tidal forces inside celestial bodies can provide enough energy to keep important solvents for living systems in the liquid phase. Moreover, tidal forces and their environmental consequences may strongly influence habitability of planets and other celestial bodies and may result in special forms of live and living conditions. A prerequisite to calculate such tidal interactions and consequences is depending on simulations for tidal accelerations in a multi-body system. Unfortunately, from measurements in many extrasolar planetary systems only few physical and orbital parameters are well enough known for investigated celestial bodies. For calculating tidal acceleration vectors under missing most orbital parameter exactly, a simulation method is developed that is only based on a few basic parameters, easily measurable even in extrasolar planetary systems. Such a method as being presented here, allows finding a relation between the tidal acceleration vectors and potential heating inside celestial objects. Using values and results of our model approach to our solar system as a “gold standard” for feasibility allowed us to classify this heating in relation to different forms of volcanism. This “gold standard” approach gave us a classification measure for the relevance of tidal heating in other extrasolar systems with a reduced availability of exact physical parameters. We would help to estimate conditions for the identification of potential candidates for further sophisticated investigations by more complex established methods like viscoelastic multi-body theories. As a first example, we applied the procedures developed here to the extrasolar planetary system TRAPPIST-1 as an example to check our working hypothesis.

Outcomes of repeated decision--making processes may be affected by adversarial actors, without being noticed. Adversaries may try to gain knowledge about a particular decision--making process, identify its decision--makers, and guess which underlying decision support model is used. Then they can simulate the process, and craft different scenarios to affect its decision outcomes. Therefore, designers of decision support systems need to incorporate this in the decision modeling phase. The purpose of this study is to demonstrate this for the repeated decision--making in a patent application process. In this process, two sequential decision outcomes can be affected by adversarial actors: a company's decision to which type of patent office to send a patent request to, and the decision of a specialized patent officer to grant an application, or not. It is motivated that the company's decision--maker is \emph{bounded} rational. A theory for information--theoretic bounded rational decision--making under uncertainty proposed by Ortega et al.\ is adopted to model this type of decision--maker. A framework is provided to simulate a number of scenarios that adversaries may deploy to affect decision outcomes of a repeated patent application decision--making process. The framework is also utilized for statistically testing the presence of the scenarios, and to demonstrate how to discourage adversaries from deploying them.

Cathepsin D (CatD; EC 3.4.23.5) family peptidases of parasitic organisms are regarded as potential drug targets as they play critical roles in the physiology and pathobiology of parasites. Previously, we characterized the biochemical features of cathepsin D isozyme 2 (CatD2) in the carcinogenic liver fluke Clonorchis sinensis (CsCatD2). In this study, we performed all-atomic molecular dynamics simulations by applying different systems for the ligand-free/bound forms under neutral and acidic conditions to investigate the pH-dependent structural alterations and associated functional changes in CsCatD2. CsCatD2 showed several distinctive characteristics as follows: 1) CsCatD2-inhibitor complex formed more hydrogen bonds; 2) acidic pH caused major conformational transitions from open to closed state in this enzyme; 3) neutral pH induced displacement of the N-terminal part to hinder the accessibility of the active site and open allosteric site of this enzyme; and 4) the flap dynamics metrics, including distance (d1), TriCα angles (θ1 and θ2), and dihedral angle (ϕ), account for the asymmetrical twisting motion of the active site of this enzyme. These findings provide an in-depth understanding of the pH-dependent structural dynamics of CsCatD2 and basic information for the rational design of an inhibitor as a drug targeting CsCatD2.

Electrochemical-mechanical interactions, in particular pressure-induced ones, have been identified to be a cause for lithium-plating in lithium-ion cells. Mechanically-induced porosity inhomogeneities in the separator layers due to electrode expansion during charging especially lead to cell internal balancing currents and can cause localized plating. To identify cell-format and cell-material dependent mechanical weak spots, a layer-resolved mechanical simulation of different cell types and cell-material combinations is presented in this work. The simulation results show distinctive layer strain patterns for different cell-types that coincide with localized lithium-plating found in post-mortem cells. Additionally, the effects of cell bracing in battery modules is investigated and a method to mitigate the increased layer strain due to bracing counterforces is proposed that also increases cell energy density for hardcase-type automotive cells.

The calculation of echo intensity involved in the SAR image simulation is usually based on the electromagnetic formula or approximate formula derived under certain assumptions. However, the parameters used in these formulas are often difficult to obtain, and the formulas have errors with the actual situation. In this paper, a method of embedding deep neural network (DNN) into the simulation process based on ray tracing is proposed, so that the DNN model can be directly used to fit the calculation formula of echo intensity from real SAR images. Simulation results show that this method can obtain SAR images with high similarity.

Large office buildings are responsible for a substantial portion of energy consumption in urban districts. However, thorough assessments regarding the Nordic countries are still lacking. In this paper we analyse the largest dataset to date for a Nordic office building, by considering a case study located in Stockholm, Sweden, that is occupied by nearly a thousand employees.Distinguishing the lighting and occupants’ appliances energy use from heating and cooling, we can estimate the impact of occupancy without any schedule data. A standard frequentist analysis is compared with Bayesian inference, and the according regression formulas are listed in tables that are easy to implement into building performance simulations (BPS). Monthly as well as seasonal correlations are addressed, showing the critical importance of occupancy.A simple method, grounded on the power drain measurements aimed at generating boundary conditions for the BPS, is also introduced; it shows how, for this type of data and number of occupants, no more complexities are needed in order to obtain reliable predictions. For an average year, we overestimate the measured cumulative consumption by only 4.7%. The model can be easily generalised to a variety of datasets.

Vertical-channel organic dual-gate/base transistors would be highly interesting since vertical organic transistors are the fastest organic transistors demonstrated today. However, incorporating a dual gate/base structure into an ultra-short channel vertical architecture represents a substantial challenge. Here, we successfully realize a new device concept of vertical organic permeable dual-base transistors (OPDBTs), where either of both base electrodes can be used to change the on-currents and tune the threshold voltages. The optimized devices yield a high on-current density of 1.54 A cm^-2 and a large current gain of 9.2×10⁵, corresponding to a high transmission value of 99.998%. The detailed operation mechanisms are investigated by calibrated TCAD simulations with the Poole-Frenkel mobility model, Gaussian density of states and tunneling model. Finally, high-performance logic circuits, e.g. inverter, NAND/AND computation functions are demonstrated with one single OPDBT operating at supply voltages of < 2.0 V. We believe that OPDBTs offer a compact and technologically simple hardware platform with excellent application potential for vertical-channel organic transistors in complex logic circuits.

Considering the need to reduce greenhouse gas emissions, onshore wind energy is certain to play a major role in future energy systems. This topic has received significant attention from the research community, producing many estimations of Europe's onshore wind potential for capacity and generation. Despite this focus, previous estimates have relied on distribution assumptions and simulation schemes that summarily under predict both the amount of available future wind capacity as well as its performance. Foremost in this regard is the common use of contemporary, or at least near-future, turbine designs which are not fitting for a far-future context. To fulfill this role, an improved, transparent, and fully reproducible work flow is presented for determining European onshore wind potential. Within a scenario of turbine cost and design in 2050, 13.5 TWof capacity is found to be available, allowing for 34.4 PWh of generation. By sorting the explicitly-placed potential generation locations by their expected generation cost, national relations between turbine cost and performance versus a desired capacity are exposed. In this way, it is shown that all countries possess some potential for onshore wind energy generation below 4 €_ct kWh^-1. and, furthermore, that it is unlikely for these costs to exceed 6 €_ct kWh^-1.

In this work we present the results obtained with an artificial neural network (ANN) which we trained to predict the expected output of high-order harmonic generation (HHG) process, while exploring a multi-dimensional parameter space. We argue on the utility and efficiency of the ANN model and demonstrate its ability to predict the outcome of HHG simulations. In this case study we present the results for a loose focusing HHG beamline, where the changing parameters are: the laser pulse energy, gas pressure, gas cell position relative to focus and gas cell length. The physical quantity which we predict here using ANN is directly related to the total harmonic yield in a specified spectral domain (20-40 eV). We discuss the versatility and adaptability of the presented method.

This work analyzes the severity and risk associated with Automatic Dependent Surveillance-Broadcast (ADS-B) message drop out in Detect and Avoid (DAA) function of Unmanned Aircraft System (UAS). Performance assessment of the Universal Access Transceiver (UAT) ADS-B message implies that in some cases ADS-B fails to update within a specified update interval, which is referred to as drop out in this work. ADS-B is a fundamental surveillance sensor for both class 1 and class 2 DAA systems. Message loss or drop out has been found as one of the common limitations of the ADS-B system. The key feature of this study is incorporating the update rate of real ADS-B data transmitted from the manned aircraft. The data were received from the Grand Forks International Airport, North Dakota. Monte Carlo method has been adopted to resolve encounter scenarios in the presence of drop out. The change in the alert triggered by the UAS DAA in the presence of ADS-B drop out has been investigated. Furthermore, the risk matrices are created to quantify the associated risk with drop out affected alerts. Simulation results depict that both the duration of drop out and DAA look-ahead time affect the alert-triggering function of UAS. With a small look- ahead window and longer duration of drop out, the number of warning alerts increases. Also, alerts are affected more during an overtaking encounter than that of a head-to-head encounter. A system-level analysis is also carried out to recognize the potential reasons behind the ADS-B drop out.

Subsurface temperature is the key parameter in geothermal exploration. An accurate estimation of the reservoir temperature is of high importance and usually done either by interpolation of borehole temperature measurement data or numerical modeling. However, temperature measurements at depths which are of interest for deep geothermal applications (usually deeper than 2 km) are generally sparse. A pure interpolation of such sparse data always involves large uncertainties and usually neglects knowledge of the 3D reservoir geometry or the rock and reservoir properties governing the heat transport. Classical numerical modeling approaches at regional scale usually only include conductive heat transport and do not reflect thermal anomalies along faults created by convective transport. These thermal anomalies however are usually the target of geothermal exploitation. Kriging with trend does allow including secondary data to improve the interpolation of the primary one. Using this approach temperature measurements of depths larger than 1,000 m of the federal state of Hessen/Germany have been interpolated in 3D. A 3D numerical conductive temperature model was used as secondary information. This way the interpolation result reflects thermal anomalies detected by direct temperature measurements as well as the geological structure. This results in a considerable quality increase of the subsurface temperature estimation.

An important aspect of PET imaging in clinical application is the localization and detection of tumors and lesions by administering a predetermined amount of radiotracer. This allows for example, a detailed view of what is going inside the patient body in cellular level. The quality of PET image is strongly dependent on the amount of administrated radiotracer and the patient’s body parameters. As the amount of injection radiotracer increases, the quality of resulting image increases and the lesion detection efficiency increases. The PET examiner society recognizes that any dose of radiotracer is associated with some possible radiation risks. It can harmful to the patient if essential PET imaging session is not made due to fear of radiation risk. In order to ensure the highest quality diagnosis and the smallest radiation risk, the patient should receive the smallest amount of radiotracer that provide image with sufficient quality. Our study is focused on proposing an efficient PET simulation tool that predict the smallest possible amount of administrated radiotracer to provides the appropriate diagnostic information based on significant patient’s body parameters (weight, age) at fixed scanning to improve the clinical diagnostic process in term of tumor detecting and localization. We have built a model of particular PET scanner and model of patient based on real MRI image and digital anthropomorphic phantom of our region of interest (brain). We have performed Monte Carlo simulation for whole PET procedure with special parameter In evaluating stage, a dataset of 60 patient is used and 11 independent dose prediction simulation for each patient are performed. We conclude that our simulator perform a desirable and efficient prediction of injection radiotracer amount that optimizes the current clinical amount up to 28%. In addition, we found that the total injected radiotracer dosage for adult patients are mostly affected when considering patient weight rather than patient age.

Generator automatic voltage control device (AVC) is an automatic voltage and reactive power optimization control terminal on the power plant side. Aiming at improving the performance of generator automatic voltage control device, this paper introduces a detection method of AVC substation performance based on virtual dispatching terminal environment. During the testing, the upper computer of redundant power plant is connected to the virtual dispatching terminal environment to simulate the sending instructions of AVC master station, the behavior of AVC sub stations and the excitation system of generators. The performance of AVC substation is evaluated according to the feedback adjustment results, which can effectively detect the abnormal behavior of AVC substation in power plant.

In this study, regression analyses were used to find a relationship between the rain gauge rainfall rate R and radar reflectivity Z for the urban catchment of the Służewiecki Stream in Warsaw, Poland. Rainfall totals for 18 events which were measured at two rainfall stations were used for these analyses. Various methods for determining calculational values of radar reflectivity in reference to specific rainfall cells with 1-km resolution within an event duration were applied. The influence of each of these methods on the Z-R relationship was analyzed. The correction coefficient for data from the SRI (Surface Rainfall Intensity) product was established, in which the values of rainfall rate are calculated based on parameters a and b determined by Marshall and Palmer. Relatively good agreement between measured and estimated rainfall totals for the analyzed events was obtained using the Z-R relationships as well as the correction coefficient determined in this study. Rainfall depths estimated from radar data for two selected events were used to simulate flow hydrographs in the catchment using the SWMM (Storm Water Management Model) hydrodynamic model. Different scenarios were applied to investigate the stream response to changes in rainfall depths, in which the data both for 2 existing as well as 64 virtual rain gauges assigned to appropriate rainfall cells in the catchment were included.

One of the principal hallmarks of Alzheimer’s disease (AD) is related to the aggregation of amyloid-β fibrils in an insoluble form in the brain, also known as amyloidosis. Therefore, a prominent therapeutic strategy against AD consists either in blocking the amyloid aggregation and/or destroying the already formed aggregates. Natural products have shown significant therapeutic potential as amyloid inhibitors from in vitro studies as well as in vivo animal tests. In this study, the interaction of five natural biophenols (curcumin, dopamine, (-)-Epigallocatechin-3-gallate, Quercetin, and Rosmarinic acid) with the amyloid-β(1-40) fibrils has been studied through computational simulations. The results allowed the identification and characterization of the different binding modalities of each compounds and their consequences on fibril dynamics and aggregation. It emerges that the lateral aggregation of the fibrils is strongly influenced by the intercalation of the ligands, which modulate the double-layered structure stability.

The United Arab Emirates (UAE) is significantly dependent on desalinated water and groundwater resource, which is expensive and highly energy intensive. Despite the scarce water resource, only 54% of the recycled water was reused in 2015. In this study, an “Oasis” complex comprised of Sustainable Farming Compartments (SFCs) was proposed for reusing treated wastewater to decrease the ambient temperature of the SFC via an evaporative cooling system. A prototype SFC with half the original scale (width = 1.8 m, depth = 1.5 m, front height = 1.2 m back height = 0.9 m) was designed, built, and tested in an environmentally controlled laboratory and field site to evaluate the feasibility and effectiveness of the SFC under the climatic conditions in Abu Dhabi. Based on the experimental results, the temperature drops obtained from the SFC in the laboratory and field site were 5 ̊C at initial relative humidity of 60% and 7- 15 ̊C at initial relative humidity of 50%, respectively. An energy simulation using dynamic numerical simulations was performed in comparison to the results of the experiment. The energy-based dynamic simulation shows good agreement with the experimental results. The total power consumption of the SFC system was approximately three and a half times lower than that of an electrical air conditioner.

Nuclear export of viral mRNAs, is an essential step in the HIV replication cycle. This role is played by a small regulatory protein of HIV-1 called Rev.The N-terminal region of Rev contains an arginine-rich sequence. The arginine-rich motif (ARM) is located between amino acids 38-50 and forms an alpha-helical secondary structure. Expression of the structural proteins of human immunodeficiency virus type 1 requires the direct interaction of multiple copies of the viral Rev protein with its highly structured RNA target sequence, the Rev Response element (RRE). The major viral proteins are not produced if this transport of RNA is stopped. Therefore, knowledge of Rev structure is essential for understanding of its cooperative binding to the RRE, for understanding the mechanism of HIV infection and for the development of antiviral drugs that interfere with Rev’s essential functions and for acknowledgment of good candidate drugs for treatment of AIDS. To understand how REV interact with RRE element of HIV-RNA and its formation of oligomeric complex it is better to characterize the domain wise structure of REV with regard in function of each domain. Due to lack of structural data on Rev no single compound is reported as inhibitor of REV expect antiviral drugs. Identification of a high-affinity RNA-binding site for the human immunodeficiency virus type 1 Rev Protein is much more important. The ARM is a highly specific sequence which allows for the multimerization of Rev and also binding of REV with RNA. Here we are first time exploring the structural characteristics of REV protein both in free form and in complex with RNA at domain function level especially explore the role of ARM motif in REV HIV-1 protein as RNA binding sites by molecular dynamics (MD) simulation and homology modeling studies. Results indicate that the arginine-rich motif (ARM) is crucial in stability of this complex. The residues ARG38, 39, 41, 43, 44, 48, 50, and ASN40 are most interacting with nucleobases of RRE in Crystal structure of Rev and Rev-response-element RNA complex. Our study plays a major role in elaboration of binding of RNA with REV and pave the way for further investigation for therapeutically agent for HIV.

Human factors are the most relevant issues contributing to adverse events in obstetrics. Specific training of Crisis Resource Management (CRM) skills (i.e., problem solving and team management, resource allocation, awareness of environment, and dynamic decision-making) are now widespread and are often based on High Fidelity Simulation. In order to be used as a guideline in simulated scenarios, they need to be translated into specific and observable behavioral markers. To this purpose, we developed a set of observable behaviors related to the main elements of CRM in the delivery room. The observational tool was then adopted in a two-days seminar on obstetric hemorrhage where teams working in obstetric wards of six Italian hospitals took part to simulations. The tool was used as guide for the Io and as a peer-to-peer feedback. It was then rated for its usefulness in facilitating the reflection upon one’s own behavior, its ease of use, and its usefulness for the peer-to-peer feedback. The ratings were highly positive, around 4 in a 5-point scale. The CRM observational tool is therefore a useful, quick and easy solution to facilitate the debriefing, the peer-to-peer feedback and, most of all, the transfer of safe behavior from simulation to everyday practice.

Fiber-metal laminates (FMLs) such as Kevlar reinforced aluminum laminate (ARALL), Carbon reinforced aluminum laminate (CARALL), and Glass reinforced aluminum laminate (GLARE) offer great potential for weight reduction applications in automobile and aerospace construction. In order to investigate the feasibility for utilizing such materials in the form of laminates, sheet hydro-bulging tests are studied under the condition of uniform blank holder force for three-layered aluminum and aluminum-composite laminates using orthogonal carbon and Kevlar as well as glass fiber in the middle. The experimental results validate the finite element results and they exhibited that the forming limit of glass fiber in the middle is the highest among the studied materials, while carbon fiber material performs the worst. Furthermore, the crack modes are different for the three kinds of fiber materials investigated in the research. This study provides fundamental guidance for the selection of multi-layer sheet materials in the future manufacturing field.

The future of machine tools will be dominated by highly flexible and interconnected systems, in order to achieve the required productivity, accuracy and reliability. Nowadays, distortion and vibration problems are easily solved in labs for the most common machining operations by using models based on equations describing the physical laws of the machining processes; however additional efforts are needed to overcome the gap between scientific research and the real manufacturing problems. In fact, there is an increasing interest in developing simulation packages based on “deep-knowledge and models” that aid machine designers, production engineers or machinists to get the best of the machine-tools. This article proposes a methodology to reduce problems in machining by means of a simulation utility, which uses the main variables of the system&process as input data, and generates results that help in the proper decision-making and machining planification. Direct benefits can be found in a) the fixture/clamping optimal design, b) the machine tool configuration, c) the definition of chatter-free optimum cutting conditions and d) the right programming of cutting toolpaths at the Computer Aided Manufacturing (CAM) stage. The information and knowledge-based approach showed successful results in several local manufacturing companies and are explained in the paper.

The next future using machine tools will be dominated by highly flexible and interconnected systems, in order to achieve the required productivity, accuracy and reliability. Nowadays, distortion and vibration problems are easily solved for the most common cases by sing models based on equations describing the physical laws dominating the machining process; however additional efforts are needed to overcome the gap between scientific research and the real manufacturing problems. In fact, there is an increasing interest in developing simulation packages based on “deep knowledge and models” that aid the machine designer, the production engineer, or machinists to get the best of their machines. This article proposes a systematic methodology to reduce problems in machining by means of a simulation utility, which recognizes, collects and uses the main variables of the system/process as input data, and generates objective results that help in the proper decision-making. Direct benefits by such an application are found in a) the fixture/clamping optimal design, b) the machine tool configuration, c) the definition of chatter free optimum cutting conditions and the right programming of cutting tool path at the Computer Aided Manufacturing (CAM) stage. The information and knowledge-based approach showed successful results in several local manufacturing companies.

Although the spanwise periodicity within the gap between two tandem circular cylinders has been observed by some researchers, there is a lack of systematic study on the properties of this pe-riodicity. For the spanwise periodicity within the gap, this study aims to ascertain its characteris-tics, its influences on the flow field, and its variation trend with increasing spacing ratio. By nu-merically simulating the flow around two tandem circular cylinders with a diameter ratio of d/D=0.6 and seventeen spacing ratios (L/D=1.00~6.00) at Re=3900, this study shows four flow re-gimes: Reattachment Flow (L/D=1.00~3.15), Bi-stable Flow (L/D=3.24), Intermittent Lock-in Co-shedding (L/D= 3.30~3.50) and Subharmonic Lock-in Co-shedding (L/D=4.00~6.00). Further, de-pending on the spanwise periodicity length of the time-averaged flow structures (i.e. Pz) within the gap, Reattachment Flow is, for the first time, subdivided into three new sub-flow regimes: Small-scale Periodic Reattachment (L/D=1.00~1.50, Pz/D=(0, 4]), Large-scale Periodic Reattachment (L/D=2.00~2.25, Pz/D>4) and Non-periodic Reattachment (L/D=2.50~3.15, no spanwise periodicity). The formation mechanisms are elaborated by analyzing the combined effect of both the L/D value and the spanwise-averaged time-averaged reattachment angle of the downstream cylinder. Moreover, this study proves that the newly-defined Small-scale Periodic Reattachment and Large-scale Periodic Reattachment are responsible for the pronounced asymmetry of the flow along the transverse direction within the gap. In addition, detailed flow properties and statistical pa-rameters are provided for each flow regime, such as velocity, vorticity, force coefficient, separa-tion/reattachment angle, Strouhal number and Q-criterion.

The purpose of this research was to analyze the moderating effect of clean energy innovation on the relationship between corporate carbon footprint and corporate profits in those industrial sectors associated with high demand for fossil fuels in which it is "hard to abate" CO₂e emissions. It used a longitudinal research design, in particular a panel study under a structural equation modeling (SEM) approach, based on partial least squares. For the longitudinal moderation analysis, this research employed the Bayesian method by defining a multiple-indicator latent growth curve model (B-LGC model). A global sample was used consisting of 7,827 firm-year observations between 2015 and 2021 corresponding to 167 international firms. The results revealed a very significant impact of the corporate carbon footprint on corporate profits. Likewise, the results showed that innovations in clean energy, when measured as the consumption of renewable energy, positively moderates the relationship between the greenhouse gas emissions from the value chain associated with Scope 3 of the Greenhouse Gas (GHG) Protocol, and the gross profit margin obtained. Besides the academic contribution represented by the moderating effect of clean energy innovation, these findings imply that a more detailed understanding of the emissions of the entire value chain (Scope 3 CO₂e) by executives and managers of high emitting CO₂e companies represents an effective mechanism to obtain higher profits, create competitive advantages and, at the same time, achieve a net zero emissions strategy. More importantly, public policy makers will be able to use these results to revise CO₂e-related policies paying more attention to the Scope 3 CO₂e emissions produced by these companies, to formulate regulatory and control mechanisms that stimulate clean energy innovation.

Twin pregnancies are highly undesirable in dairy cattle; they compromise the health and wellbeing of a cow, and its incidence dramatically impairs the farm economy. Recently, a genomic prediction for twin pregnancies has been developed. The objective of this study was to assess cow, environmental and management risk factors affecting the incidence of twin pregnancies in high-producing dairy cows in their first lactation, with special emphasis placed on the genomic prediction values for twin pregnancy. Our study population of primiparous cows proved valuable in identifying factors other than genomic predictive values influencing the twin pregnancy rate. The odds ratio for twin pregnancy was 0.85 (p &lt;0.0001) for each unit of a prediction value increase, 3.5 (p = 0.023) for cows becoming pregnant during the negative photoperiod, and 0.33 (p = 0.016) for cows producing ≥42 kg of milk at AI, compared to the remaining cows producing &lt;42kg of milk. As a general conclusion, the practical implication of our findings is that genomic prediction values can identify the risk of twin pregnancy at herd level. Given the cumulative effect of genomic selection, selecting for animals with reduced genetic risk of twin pregnancies can contribute to reduce its incidence in dairy herds.

HIV-1 is a complicated and perplexing virus. It infects T cells, reverse transcribes its RNA into DNA, utilizes its host DNA machinery to replicate its HIV-DNA, translates the HIV-DNA into proteins, assembles itself for a budding escape from the T cell, and rapidly mutates its conformation. Partially, due to its complexity, there remains no cure for HIV or AIDs. However, recently with the discovery of TALENs, the use of zinc fingers, and most of all the applications of CRISPR-Cas9 technology, has given researchers new hope in finding alternative gene therapies and treatments for diseases. With more focus on CRISPR-Cas9, this new and novel technology uses a guiding RNA, sgRNA, to lead a Cas9 nuclease to its target for deletion or to change that DNA site. CRISPR-Cas9 can delete point mutations and multiple DNA sites. Because CRISPR can alter DNA sequences, several scientists have conducted research into CRISPR, possibly treating more diseases such as cancer, diabetes, and even HIV. HIV-1 drew the focus of a researcher named Dr. Ebina in 2013 when he was the first to design and apply CRISPR-Cas9 to genes found in the binding sites of HIV-1, inhibiting HIV-1 gene expression. Since 2013, several other researchers have blocked HIV replication and infection through CRISPR-Cas9 targeting the receptors of T cells called the CC chemokine receptor 5 or CCR5. HIV-1 binds to the CD4 receptor of T cells, which consists of co-receptors CCR5 and CXCR4. If CCR5 expression can be removed, the HIV virus cannot bind to T-cells, blocking the initial attachment stage, and discontinuing the infection. However, there remain obstacles and issues for the CRISPR deletion of CCR5 for treating HIV-1. The issues include: 1) finding new and safe methods of CRISPR-Cas9 delivery, 2) clearing the latent HIV reservoirs, 3) improving the sgRNA design to avoid off-target mutations or deletions, and 4) effectively analyze the viral escape of HIV from CRISPR-Cas9 modifications. Therefore, the purpose of this review is to discuss possible techniques for removing the obstacles that can lessen the potential of CRISPR to delete CCR5, repressing HIV-1 into long-term remission or a functional cure.

This initial report of a longitudinal study of 192 English hospital nurses has measured Nursing Values (the 6Cs of nursing); Personality, Self-Esteem and Depression; Burnout Potential; Work-Life Balance Stress; ‘Hardy Personality’; and Intention to Leave Nursing. Correlational, component and cluster analysis identifies four groups: “The Soldiers” (N = 79) , with medium scores on most measures, who bravely ‘soldier on’ in their nursing roles, in the face of numerous financial cuts to the National Health Service, and worsening nurse-patient ratios; “Cheerful Professionals” (N = 54), coping successfully with nursing roles, and a variety of challenges, in upwardly mobile careers; “High Achievers” (N = 39), senior nurses with strong profiles of a ‘hardy personality’, and commitment to fundamental nursing values; “Highly Stressed, Potential Leavers” (N = 20), with indicators of significant psychological distress, and difficulty in coping with nursing role challenges. We propose a model of co-counselling and social support for this distressed group, by nurses who are coping more successfully with multiple challenges. We discuss the role of nurse educators in fostering nursing values, and developing and supporting ‘hardy personality’ and emotional resilience in recruits to nursing. This study is framed within the disciplinary approach of Critical Realism, which identifies the value basis for research and dialogue in developing strategies for social change.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

The advent of social commerce (SC) has transformed the landscape of online consumer behavior, emphasizing the significance of customer-to-customer relations in shaping sustainable relation-ships with customers. This research investigated the intricate relationships between social com-merce dimensions, particularly suggestions and recommendations, forums and communities, and ratings and reviews, and their influence on customer-to-customer value co-creation (C2CVCC) and sustainable customer relationships (SCRs). A questionnaire was designed and administered to 635 respondents. We examined the psychometric properties of the measurements and subse-quently applied Partial Least Squares as a Structural Equation Modeling method (PLS-SEM) for hypothesis testing. The findings reveal that the dimensions of SC significantly impact C2CVCC, with ratings and reviews playing a pivotal role. Furthermore, C2CVCC emerges as a substantial mediator in the path between SC and SCRs. The empirical analysis showcases strong support for the proposed model, with robust path coefficients (β) and p-values confirming direct and indirect effects. These findings offer valuable insights for businesses seeking to leverage SC and customer interactions to enhance SCRs in the digital era. Understanding the dynamics of C2CVCC within the context of SC has become essential for marketers and businesses aiming to thrive in today's competitive online marketplace.

Carbapenem antibiotics are the drug of choice for treating multidrug-resistant bacterial infections. Metallo-beta-lactamases (MBLs) are carbapenemase capable of hydrolyzing nearly all therapeutically available beta-lactam antibiotics. Consequently, a need to assess the frequency and phenotypic resistance phenomena of two MBL genes in diarrheal and urinary tract infections (UTIs). Samples were collected through a cross-sectional study, with MBLs genes detected via PCR. Two hundred twenty eight diarrheal bacteria were isolated from 240 samples. The most predominant pathogens were Escherichia coli (32%) and Klebsiella spp. (7%). Phenotypic resistance to amoxicillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 50.4%, 65.6%, 66.8%, 80.5%, 54.4%, 41.6%, 25.7%, 41.2%, 37.2%, and 42.9%, respectively.  Total 142 UTI pathogens were obtained from 150 urine samples, with Klebsiella spp. (39%) and Escherichia coli (24%) are the major pathogens. Phenotypic resistance to amoxycillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 93.7%, 75.0%, 91.5%, 93.7%, 88.0%, 72.5%, 13.6%, 44.4%, 71.1%, and 43%, respectively.  Twenty four diarrheal isolates carried either blaNDM-1 or blaVIM genes; the overall MBL gene prevalence was 10.5%. Thirty six UTI pathogens carried either blaNDM-1 or blaVIM genes (25.4%). Seven isolates carried both blaNDM-1 and blaVIM genes.  MBL genes exhibited a strong association with phenotypic carbapenem and other beta-lactam antibiotic resistance. Resistance to carbapenems requires active surveillance and stewardship.

This work presents noble composites of AAILs@MCM-48 by functionalizing ordered mesopo-rous silicon MCM-48 with two amino acid-based ionic liquids (AAILs) ([Emim][Gly] and [Em-im][Ala]) to improve carbon capture and selectivity of CO2 over nitrogen. Thermogravimetric and XRD analyses of the composites show that the MCM-48 support's thermal and structural in-tegrity was preserved after the AAILs were encapsulated. An N2 adsorption-desorption study at 77 K also confirms AAIL encapsulation in the porous support. Under post-combustion flue gas conditions, both [Emim][Gly]@MCM-48 and [Emim][Ala]@MCM-48 demonstrated improved CO2 adsorption in comparison to unmodified MCM-48, with a CO2 partial pressure of around 0.15 bar. In terms of maximal CO₂ uptake, the 40wt%-[Emim][Gly] composite outperformed the others at 303K, with values of 0.74 and 0.82 mmol g-1, respectively, at 0.1 and 0.2 bar. These numbers show a 10x and 5x increase, respectively, as compared to the pure MCM-48 under iden-tical conditions. In addition, the selectivity of the composites was improved significantly, at 0.1 bar, the selectivity of composites containing 40wt% [Emim][Ala] increased to 17, compared to 2 for pristine MCM-48.

Co-delivery of antigens and adjuvants to the same antigen presenting cells (APCs) can significantly improve the efficacy and safety profiles of vaccines. Here, we report amine-grafted silica nanoparticles (A-SNPs) as a tunable vaccine co-delivery platform for TLR7/8 agonists along with the recombinant influenza antigen hemagglutinin H7 (H7) to APCs. A-SNPs of two different sizes (50 and 200 nm) were prepared and coated with INI-4001 at different coating densities, followed by co-adsorption of H7. Both INI-4001 and H7 showed &gt; 90% adsorption to the tested A-SNP formulations. TNF-α and IFN-α cytokine release by human peripheral blood mononuclear cells as well as TNF-α, IL-6, and IL-12 release by mouse bone marrow-derived dendritic cells revealed that the potency of the INI-4001-adsorbed A-SNPs (INI-4001/A-SNP) formulations can be improved relative to aqueous formulation control. This improved potency was dependent on particle size and ligand coating density. In addition, slow-release profiles of INI-4001 were measured from INI-4001/A-SNP formulations in plasma with 30-50% INI-4001 released after 7 days. In vivo murine immunization studies demonstrated significantly improved H7-specific humoral and Th1/Th17-polarized T cell immune responses with no observed adverse reactions. Low-density 50 nm INI-4001/A-SNP elicited significantly higher IFN-γ and IL-17 induction over that of the H7 antigen only group and INI-4001 aqueous formulation controls. In summary, this work introduces an effective and biocompatible SNP-based co-delivery platform that enhances the immunogenicity of TLR7/8 agonist-adjuvanted subunit influenza vaccines.

Delivery systems of the biologically active substance such as proanthocyanidins (PCAN) produced through the electrospinning method were designed using a blend of poly(L-lactide-co-glycolide) and poly[(R,S)-3-hydroxybutyrate]. The research involved the structural and thermal characteristics of the developed electrospun three-dimensional fiber matrix, as well as hydrolytic degradation tests performed on them. Additionally, the release profile of PCAN from the electrospun nonwoven was determined using UV–VIS spectroscopy. Approximately 30% of PCAN was released from the tested electrospun nonwoven during the initial 15-20 days of incubation. The chemical structure of water-soluble oligomers that were formed after the hydrolytic degradation of the developed delivery system was identified through electrospray ionization mass spectrometry. Oligomers of lactic acid and OLAGA oligocopolyester, as well as oligo-3-hydroxybutyrate terminated with hydroxyl and carboxyl end groups, were recognized as degradation products released into the water during the incubation time. It was also demonstrated that variations in the degradation rate of individual mat components influenced the degradation pattern, and the number of formed oligomers. The obtained results suggest that the incorporation of proanthocyanidins into the system slowed down the hydrolytic degradation process of the poly(L-lactide-co-glycolide)/poly[(R,S)-3-hydroxybutyrate] three-dimensional fiber matrix. In addition, in vitro cytotoxicity and antimicrobial studies advocate the use of PCAN for biomedical applications with promising antimicrobial activity.

University-Business partnership for collaborative curriculum design, development and delivery is possibly the less explored dimension of University Business Collaboration (UBC). Even if some models for curricular design and development might be available, scarce information exists on how the partnership is constructed, the new curricula are designed, developed and how they are implemented. This article intends to present and discuss the experience obtained during a three-year European funded Project, namely Think4Jobs. This project exemplifies the significance and benefits of UBC in the design, development and delivery of curricula that meet the evolving demands of the labour market while promoting Critical Thinking (CT) as a foundational 21st century skill to contribute to graduates' employability. Think4Jobs project brought together a multidisciplinary team of researchers and business organisations from five European countries (Germany, Greece, Lithuania, Portugal and Romania) with interests in promoting and developing CT and mitigating eventual competence gaps. The project's success was attributed to key practices, including defining a common conceptualization of CT, employing participatory co-design, and providing common training for university and business partners. Clear objectives, explicit roles, effective communication, and ongoing evaluation further enhanced the collaboration. Experiential learning, real-work problems, and case studies reinforced the curricula, bridging the gap between academia and the labour market. By embracing these insights, future UBC initiatives can empower graduates with the necessary skills to stand out in an ever-changing labour market, contributing to enhanced education and successful careers.