With the development of free trade port in Hainan Island, the construction of tourist roads around the island is also in full swing. Under the weather conditions of strong typhoon and rainstorm in Hainan, the highway cutting slope built on the coastal weak sandy terraces has strong sand loss and is easy to be scour by rainfall. MICP green spray irrigation solidification technology is used to strengthen the sandy cutting, and pore water pressure monitoring is carried out on the slope model during MICP solidification and rainfall scour. Combined with the model pore water pressure and flow slip failure pattern, dynamic analysis was carried out. The results show that MICP sprinkler irrigation technology can solidified the surface of the slope model in a short time, and the cementation depth of the model reaches 4cm after three sets of rotation reinforcement. The surface reinforcement effect is good, and the sand samples are closely connected. Under the erosion effect of simulated rainfall intensity, the sand loss of the slope is weakened, and no sand binding damage occurs, and the integrity is enhanced. Due to the cementation between sand grains, most of the rainfall was converted into runoff, and the slope slid after 150s. When the slope began to slip, the leading edge of the slope model lost sand and unloaded, and the failure mode was graded creep slip failure. Finally, the slope was divided into several blocks due to the continuous expansion of cracks after the slope failure. The erosion stability of the sandy slope under heavy rains is optimized and the sand loss is prevented effectively. In this study, a new method of MICP remediation techniques is proposed, which provides a new test basis for the application of MICP technology in practical engineering.

Landslides are a frequent and recurrent problem in hilly regions of India and predicting them is always a challenging task. In this paper, an attempt was made to deal with this problem using advanced physical and numerical modeling methods. Detailed understanding of the initial slope failures is very interesting, and challenging at the same time, in the design and development of wireless sensor network based on early warning of landslide monitoring. A small scale physical model was developed to assess the instability through a sensor network with variable rain fall intensity. This was achieved by increasing the simulated rain water flow intensity in different time spans (dry condition, at t=0 to t= 30 min, 0.5 mm/min at t=30 to t= 60 min, 0.75 mm/min at t=60 to t=91 min and 1 mm/min at t=91 to t= 120 min). The water level and movement in the slope was recorded by rainfall sensor, vibration sensor, soil moisture sensor and a digital camera. The following changes were observed during the slope failure: a) movement of small particles at top of the slope; b) initial failure of medium size soil particle; c) scouring of soil mass; d) whole slope collapse. The obtained results clearly indicated the superiority and effectiveness of the proposed system in providing a factor of safety for the progressive slope.

In slope engineering, the foundation grooves of slope protection gird beams are mostly excavated manually. However, manual excavation presents problems, such as low construction efficiency, uneven groove bottoms, inconsistent cross-section groove widths, and curved groove axis, which reduces the quality of cast-in-place grid beams or complicates the installation of prefabricated grid beams. To address these issues, a mechanized grooving device for slope protection grid beams has been developed and successfully applied in the project. The grooving device is composed of interlocking dual spiral cutter heads, a mechanism for the groove width and depth adjustment, a cutter head working platform, a platform azimuth adjuster, a cutter head sliding mechanism, a hydraulic motor, a hydraulic power system and a platform anchoring mechanism. It can be used to groove on soil and strongly weathered rock slopes at different slope angles, and the foundation grooves of slope protection gird beams of different depths and widths can be carved according to the design requirements. Moreover, the grooved trenches feature flat bottoms, consistent widths, and straight axis, making it easy to install prefabricated grid beams and greatly improving the quality of cast-in-place grid beams. According to the construction statistics of a slope project in Guangdong, the grooving speeds of the grooving device on the slope of soil and strongly weathered rock are about 1.5m/min and 0.5m/min respectively, which greatly improves the construction efficiency and quality.

Facing global warming consequences is a major issue of present times. For what concerns climate, projections say that heavy rainfalls are going to increase with high probability together with temperature rise, thus also the hazard related to rainfall induced shallow landslides will likely increase in density over susceptible territories. Different modeling approaches exist and any of them is forced to make simplifications in order to reproduce landslide occurrences over space and time. Process based models can help in quantifying the consequences of heavy rainfall on the different involved processes. In this paper, a narrative review about physically-based deterministic distributed models (PBDDMs) is presented. Models were selected based on: the adoption of the infinite slope scheme (ISS), the use of a deterministic approach (i.e., input and output are treated as absolute values), the inclusion of new approaches in modeling slope stability through the ISS. Models are presented in chronological order with the aim of drawing a timeline of the evolution of PBDDMs and to give researchers and practitioners a basic knowledge on how much has been already done. Results indicate that including vegetation effects on slope stability has raised in importance over time but that there is still the need of finding an efficient way to include them, and that in the last years the literature production seems to be more focused on probabilistic approaches.

This paper focuses on the physical attributes of land that intrinsically limit land use and possibly affect land values. In particular, we investigate if the slope of a land does decrease its price and investigate the role of land slope in forming more reliable constant-quality land price indices and aggregate house price indices. We find that, while land slopes do decrease the land price per unit, they have a small effect on the quality-adjusted land price indices in selected neighborhoods in Auckland, New Zealand, where sloped terrain is common.

Craters are the most prominent geomorphological features on the surface of celestial bodies, which is playing a crucial role in studying the formation and evolution of celestial bodies, as well as in landing and planning for surface exploration. Currently, the main automatic crater detection models and datasets focus on the detection of large and medium craters. In this paper, we created 23 small lunar crater datasets for model training based on the Chang’E-2 (CE-2) DOM, DEM, Slope, and integrated data with 7 kinds of visualization stretching methods. And then, we proposed the YOLO-Crater model for Lunar and Martian small crater detection by replacing EioU and VariFocal loss to solve the crater samples imbalance problem and introducing a CBAM attention mechanism to mitigate interference from the complex extraterrestrial environment. The results show that the accuracy (P = 87.86%, R = 66.04%, and F1 = 75.41%) of the Lunar YOLO-Crater model based on the DOM-MMS (Maximum-Minimum Stretching) dataset is the highest and better than that of YOLOX model. And the Martian YOLO-Crater, trained by the Martian dataset from the 2022 GeoAI Martian Challenge, achieves good performance with P = 88.37%, R = 69.25%, and F1 = 77.65%. It indicates that the YOLO-Crater model has a strong transferability and generalization capability, which can be applied to detect small craters on the Moon and other celestial bodies.

Understanding the factors that contribute to slope failures, such as soil saturation, is essential for mitigating rainfall-induced landslides. Cost-effective capacitive soil moisture sensors have the po-tential to be widely implemented across multiple sites for landslide early warning systems. How-ever, these sensors need to be calibrated for specific applications to ensure high accuracy in readings. In this study, a soil-specific calibration was performed in a laboratory setting to integrate the soil moisture sensor with an automatic monitoring system using the Internet of Things (IoT). This re-search aims to evaluate a low-cost soil moisture sensor (SKU:SEN0193) and develop calibration equations for the purpose of slope model experiment under artificial rainfall condition using silica sand. The results indicate that a polynomial function is the best fit, with a coefficient of determi-nation (R²) ranging from 0.92 to 0.98 and a root mean square error (RMSE) ranging from 1.17 to 2.67. The calibration equation was validated through slope model experiments, with soil samples taken from the model after the experiment finished. Overall, the moisture content readings from the sensors showed approximately a 10% deviation from the actual moisture content. The findings suggest that the cost-effective capacitive soil moisture sensors has the potential to be used for the development of landslide early warning system

Strata and surface movement induced by mining under open-pit final slope is a huge threat to mine safety. Physical model test is an important method to study mining-induced strata and surface movement laws. Because of rock joints predominantly control rock mass deformation and failure, thus physical model test leaving out of consideration of rock joints is difficult to reflect the influence of rock joints on rock mass deformation. Therefore, this paper presents a three-dimensional physical model test considering simplified dominant rock joints. This test process includes the design of testing equipment, the construction of physical model with dominant rock joint sets, conduction of mining and deformation monitoring. And mining under eastern final slope of Yanqianshan iron mine was selected as a case to study the behavior of mining-induced strata and surface movement.

The load on the top of a slope is an important cause of slope failure, and it is of great significance to study the relationship between the load and the stability of the slope. This paper uses elastic theory and Moore Coulomb's theory as transformation conditions to obtain the slope stability coefficient expression under slope top load based on the Swedish slice method. In view of the actual engineering, the corresponding slope model structure was established, and 5 sliding surfaces were set with the crack on the top of the slope as the shear outlet. According to the slope stability coefficient expression, the stability coefficient of the set sliding surface is solved. The result shows that the slope is unstable under the load. The judgment result is consistent with the GEO-STUDIO check calculation result. This method can provide reference for theory and engineering practice.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

Municipal solid waste management is a growing worldwide challenge. Landfill mining is a promising technique to reduce MSW landfills. In the present study, arbitrary embankments made of different MSW fractions are analyzed to find the safety factor of their slopes. Properties of Municipal solid waste fines (MSWF), Shredded MSW, MSW Incineration Ash, and MSW having particles less than 35 mm are used in the analysis. For doing the same, finite element-based application 'Plaxis-2D' is used. The safety of slopes is assessed while the water table is inserted, and a uniform load is applied to the embankment to establish how well they will perform in critical situations. It was found that the slope made of shredded MSW is most safe due to its low density and high friction angle, while the least safe slope is made of MSW having less than 35 mm fractions.

Slope failures pose a substantial threat to mining activity due to their destructive potential and high probability of occurrence on steep slopes close to limit equilibrium conditions, often found both in open pits and in waste and tailing disposal facilities. The development of slope monitoring and modeling programs usually entails the exploitation of in situ and remote sensing data together with the application of numerical modeling, and it plays an important role in the definition of prevention and mitigation measures aimed at minimizing the impact of slope failures in mining areas. Here we present a new methodology combining satellite radar interferometry and 2D finite element modeling for slope stability analysis at a regional scale, applied within slope unit polygons. We studied a former mining area in southeast Spain, and the method proved useful in detecting and characterizing a considerably large number of unstable slopes. Out of 1,959 slope units used for the spatial analysis of the radar interferometry data, 43 were unstable, with varying values of safety factor and landslide size. Out of the 43 active slope units, 21 exhibited line of sight velocities greater than the maximum error obtained through the validation analysis (2.5 cm/year). Eventually, this work discusses the possibility of using the results of the proposed approach to devise a proxy for landslide hazard. The proposed methodology can help to provide non-expert final users with intelligible, clear and easily comparable information to analyze slope instabilities in different settings, not limited to mining areas.

This paper provides an alternative Slope-Deflection equation for performing the static analysis of the indeterminate structures. While the conventional Slope-Deflection method introduced in undergraduate structural analysis course involves the use of fixed end moments in the Slope-Deflection equations, the proposed method employs the slope of a simply supported beam to obtain the unknown moments at the joints. Three numerical examples of continuous beams with different load configurations are chosen and the efficacy of the proposed equations is demonstrated. From the perspective of undergraduate structural analysis course in Civil Engineering education, the approach proposed in this paper offers two advantages: (1) prior knowledge of fixed beams is not required and (2) the concepts gained from determinate structural analysis are directly applicable.

In this study, UAV (Unmanned Aerial Vehicle) photogrammetry was used to monitor the ground displacement on the slope below a coal waste-rock stockyard, and to investigate the role of rainfall on this displacement. The study area is a mountainous region in Korea, where coal mining continues, and coal waste-rock is stored on the slopes of the mountain. In this area, ma-terial removal work was undertaken to reduce the steepness of the slope and driving forces in order to prevent disasters, but the strategy requires continuous monitoring to confirm the stabilization of the slope. For slope monitoring, a total of six UAV photogrammetry campaigns were conducted between April 2019 and August 2020. As a result of data processing, an orthoimage and DSM (Digital Surface Model) were generated. The ground displacement was estimated through four ways: slope extraction, displacement area evaluation, horizontal displacement, and vertical displacement analysis. During the study period, the maximum vertical displacement was 3.3 m and the maxi-mum horizontal displacement was 3.5 m. The horizontal displacement was effectively evaluated through the measurement of the movement of the drainage system using orthoimages that captured with a periodic survey. The effects of rainfall on ground displacement were also investigated. A very clear linear relationship between rainfall intensity higher than 20mm/d and ground displacement was identified. Accumulated amount of rainfall also showed good correlation with slope movement, but the frequency of rainfall intensity below 20 mm/d showed relatively low correlation with ground dis-placements.

Meganthropus palaeojavanicus was known very tall with body height of 8 feet and this made M. palaeojavanicus as the tallest hominid ever existed. This species was living in closed tropical woodland and hilly landscape as the fossil remains were found in a remote forest in Sangiran, central Java. Owing large body size, it may influence the foraging ecology of M. palaeojavanicus to cope with the terrain. In here, this study aimed to model the M. palaeojavanicus foraging ecology along terrain gradients. The model indicates that within 5 km home range radius, the most suitable foraging areas were in north east since these areas have more flat landscapes with slopes of <7.5%. While less suitable areas in north west and south west areas were characterized by hilly landscapes with rugged terrain and steep slopes with slopes of >62.8%.

Karst peaks and depressions are scattered in karst zones with strong spatial heterogeneity and fragile ecological environments and are crucial for determining the degree of karst geomorphologic development. However, realizing automatic depiction and extracting depressions with high accuracy is difficult because of their complex morphology. Herein, based on 12.5-m resolution DEM data, six typical karst peaks from depressions in southwest China were selected as the study areas and a revised terrain openness index method based on slope mutation points (ROBSMPs) was used to determine the degree of karst geomorphologic development and the boundary of karst depressions. The extent of depressions extracted by ROBSMPs and the terrain openness index method with the extent of depressions hand-drawn based on remote sensing images was compared and analyzed. The results show that compared with the topographic openness index method, the overall accuracy of karst depression extracted by ROBSMPs was improved and the perimeter, area, and raster displacement error indexes were reduced. ROBSMPs realized high-precision extraction of depressions, thereby strengthening the applicability of the topographic openness index method to karst peak zones. This study offers a new perspective and path toward the expansion of digital terrain analysis technology in karst mountainous areas and is expected to play a vital role in the extraction of similar geomorphic units in karst zones.

This paper investigates the influence of different vegetation on the permeability of the shallow soil layers of slopes under rainfall infiltration. Firstly, four large slopes are filled in the outdoor natural environment, and the overburdens of the four slopes are Magnolia multiflora, Cynodon dactylon, Magnolia multiflora mixed with Cynodon dactylon, and no vegetation. Secondly, the four slopes are cultivated in the outdoor natural environment for one year. After the vegetation overburdens are matured, the field artificial rainfall test is carried out through the self-developed artificial rainfall device to monitor the water migration law inside the four slopes in real time. Finally, the unsaturated permeability coefficients of the shallow soil layers of slopes are calculated. The results show that the infiltration rate of rainwater in each overburden slope from fast to slow is Magnolia multiflora overburden slope, no vegetation slope, Cynodon dactylon overburden slope, Magnolia multiflora mixed with Cynodon dactylon overburden slope. In the early stage of rainfall, Magnolia multiflora increases the permeability coefficient of the shallow soil layer of the slope, thus weakening the anti-seepage ability of the slope, but the influence of Magnolia multiflora is not obvious in the later stage. Cynodon dactylon and Magnolia multiflora mixed with Cynodon dactylon can significantly reduce the permeability coefficient of the shallow soil layers of the slopes, thereby increasing the anti-seepage ability of the slopes, and the mixed planting of Magnolia multiflora and Cynodon dactylon can minimize the permeability coefficient of the shallow soil of the slope, resulting in the best anti-seepage effect.

By installing FBG sensors on the geogrids, smart geogrids can both reinforce and monitor the stability for geogrid-reinforced slopes. In this paper, a geogrid-reinforced sand slope model test was conducted in the laboratory and fiber Bragg grating (FBG) sensing technology is used to measure the strain distribution of the geogrid. Based on the model test, the performance of the reinforced soil slope is simulated by finite element software Midas-GTS, and the stability of the reinforced soil slope is analyzed by strength reduction method. The relationship between the geogrid strain and safety factor is set up. The results indicate that the measured strain and calculated results agree very well. The geogrid strain measured by FBG sensor can be applied to evaluate the stability of geogrid-reinforced sand slopes.

Permeable asphalt pavement refers to an asphalt mixture layer with an air void content of more than 18% and internal water permeability and drainage capabilities, which can quickly drain away water on the road surface, improve rainy day travel safety and ride comfort. This paper aims to explore the optimal asphalt mixture mix design for long longitudinal slope roads. By using CT scanning technology to analyze the air void content of different rotated and compacted asphalt mixture specimens, and extensively testing and evaluating the performance of permeable pavement mixtures, the following conclusions are drawn: Based on the research philosophy of functional integration, a new asphalt mixture gradation suitable for long longitudinal slope roads is proposed, with the optimal key factor composition being: 0.075mm passing rate of 7%, 2.36mm passing rate of 20%, 9.5mm passing rate of 55%, and oil-stone ratio of 4.8%. The FAM mixture was divided into three parts for air void analysis, with the upper part having a slightly higher air void content than the lower part. The air void distribution diagram of the FAM mixture is concave, with higher air void rate curves on both sides and a lower middle curve. Compared with laboratory dry measurement method, CT scanning test showed slightly higher air void content in specimens. Through dynamic modulus testing, the strength requirement for road asphalt mixture in pavement structure design was evaluated. It was found that at high temperature conditions (50℃), the minimum dynamic modulus value of the FAM mixture was 323 MPa, with a peak value of 22746MPa at a temperature of -10℃ and a frequency of 25HZ. The dynamic modulus value at high temperature conditions is lower than at low temperature conditions, while the dynamic modulus value at high frequency conditions is higher than at low frequency conditions. This study provides useful information and experimental data for the design of new asphalt mixtures for long longitudinal slope roads, and has conducted in-depth research on the air void distribution and performance of the mixture, providing strong support for related research fields and practical applications.

This study addresses the peculiarities of the generation of slope movements in the context of road infrastructures and provide a predictive mapping of susceptibility to movements on slopes adjacent to road infrastructures (rockfalls). An inventory of slopes movements was mapped. From the development of the inventory of constant cases of mobilization that is used as a dependent variable, two statistical models can be obtained and compared for the same study area. One of them is based on the concept of frequency, whilst the other one is based on the application of a logistic regression. The results reveal the preponderant importance of lithology as a predictive variable, followed, at a considerable distance, by the slope gradient. Likewise, the importance of an unnatural and characteristic variable area of study, such as the presence of artificial cuts, is indicated as a causative factor. The results show a high degree of coincidence between the tendency of susceptibility predicted by the model, and the effective presence of empirical mobilization signs on the slopes, with Area Under Curve (AUC) values for Receiver Operating Characteristics (ROC) around 0.8.

In Ethiopia, land degradation in the form of gully development and soil nutrient depletion is a very serious issue. The goal of this study is to determine how different types of land management practices and slope positions affect particular soil physico-chemical characteristics in the Agamssa watershed. Using systematic sampling techniques, soil samples were taken using a sampling quadrat (15 * 15 m) that was placed 50 m apart from one another. A total of 54 quadrats were planted at three slope positions: upper (>15%), middle (10–15%), and foot (3–10%) slope respectively. 18 composite soil samples were then. A two-way ANOVA was used to analyze the data, and the Least Significant Difference (LSD) test was used to separate the means at p ≤ 0.05. According to the study's findings, the value of most soil physical and chemical characteristics was higher in closed area than on open grazing land, as well as at foot slope position compared to middle and upper slope positions. The higher mean value (7.3 ppm) was recorded at the foot slope, while the lower mean value (4.9 ppm) was found at the upper slope position. The exchangeable cations such as Mg+2, K+, and Na+ were significantly (p≤ 0.01) affected by the main effect of land-use types. The higher mean values of Mg+2 (9.70 mq/100g), K+ (0.38 mq/100 g), and Na+ (0.035 mq/100 g) were found at area closure, whereas the lower mean values of Mg+2 (7.33 mq/100g), K+ (0.30 mq/100 g), and Na+ (0.027 mq/100g) were recorded at open grazing land. It was able to conclude this study that area closure enhances the physical and chemical qualities of soil and recovers woody plant species. Therefore, converting open grazing land into a closure area is advised.

Despite the popularity of infant swimming programs, no evidence exists to determine whether they influence infants’ judgements and behavior when confronted with bodies of water. In the current study we examined whether the total number of swimming sessions an infant had participated in predicted whether they avoided a body of water they could enter via an edge (n = 101 infants) or a slope (n = 77 infants). An initial regression analysis revealed no association between the number of sessions and avoidance of the water via either type of entry. However, a secondary analysis of infants who had participated in fewer or more than 10 sessions revealed a significant interaction between number of sessions and type of entry into the water. Infants who participated in more than 10 sessions were more likely to avoid the water if they could access it via an edge but significantly more likely to enter the water if they could access it via a slope. Because we tested the two groups of infants in different countries, further research is warranted to determine if cultural differences in child rearing practices or variations in the content and/or teaching of the swimming programs might explain these intriguing findings.

Karakoram highway (K.K.H.) the only road link between two countries China and Pakistan. This road network is essential for two countries due to its strategic location and socioeconomic. The highway is more vulnerable due to landslide disasters, especially in rain and snow melting seasons, and different kinds of mass movement activities have occurred along K.K.H., such as rockfall, debris flow, and snow avalanche. The slope stability problems are widespread along with Karakorum (K.K.H.) between Besham city and the Dasu area because of the high seismic zone, rainfall, snow melting, and complex geology slope geometry, week, and adverse discontinuities sets. The detailed fieldwork was done along the Karakorum highway to minimize the risk of slope stability and for planning purposes in Besham to Dasu area and selected nine road-cut slopes. However, in these nine selected roadcut slopes, three slopes were already failed, four slopes are partially stable, and two slopes were stable. Both kinematic and empirical approaches are applied on all these nine road cut slopes and their discontinuities. The kinematic result has shown that all kinds of mode failure such as Toppling, Planar, and Wedge failure mode occurred in these slopes. The RMRb result has shown that all discounters lie in between fair to good rock. Both discrete and continuous (S.M.R.) results show that all discontinuity sets lie between the unstable, partially stable, and stable conditions.

The application of naturally ventilated pig buildings (NVPBs) with outdoor exercise yards is on the rise mainly due to animal welfare considerations, while the issue of emissions from the buildings to the surrounding environment is important. Since air pollutants are mainly transported by airflow, the knowledge on the airflow characteristics downwind the building is required. The objective of this research was to investigate airflow properties downwind of a NVPB with a roofed outdoor exercise yard for roof slopes of 5°, 15°, and 25°. Air velocities downwind a 1:50 scaled NVPB model were measured using a Laser Doppler Anemometer in a large boundary layer wind tunnel. A region with reduced mean air velocities was found along the downwind side of the building with a distance up to 0.5 m (i.e. 3.8 times building height), in which the emission concentration might be high. It was found that a smaller roof slope (i.e. 5° slope) resulted in a higher and shorter wake zone and thus a shorter air pollutant dispersion distance. It was concluded that a smaller roof slope could contribute to the dilution of air pollutants and a lower air pollutant concentration near the ground.

This study presents an exploration into identifying the interactions between ocean waves and the continental margin in the origination of double-frequency (DF, 0.1-0.5 Hz) microseisms recorded at 33 stations across East Coast of USA (ECUSA) during a ten-day period of ordinary ocean wave climate. Daily primary vibration directions are calculated in three frequency bands and projected as great circles passing through each station. In each band, the great circles from all stations exhibit largest spatial density primarily near the continental slope in the western North Atlantic Ocean. Generation mechanisms of three DF microseism events are explored by comparing temporal and spatial variations of the DF microseisms with the migration patterns of ocean wave fronts in Wavewatch III hindcasts. Correlation analyses are conducted by comparing the frequency compositions of and calculating the correlation coefficients between the DF microseisms and the ocean waves recorded at selected buoys. The observations and analyses lead to a hypothesis that the continental slope causes wave reflection, generating low frequency DF energy and that the continental shelf is where high frequency DF energy is mainly generated in ECUSA. The hypothesis is supported by the primary vibration directions being mainly perpendicular to the strike of the continental slope.

In the last years, the development of low-cost GNSS sensors allowed monitoring in a continuous way movement related to natural processes like landslides with increasing accuracy and limited efforts. In this work, we present the first results of an experimental low-cost GNSS continuous monitoring applied to the unstable slope affecting the Madonna del Sasso Sanctuary (NW Italy). The courtyard of Sanctuary is built of two unstable blocks delimited by high cliff. Previous studies and non-continuous monitoring showed that blocks suffer a seasonal cycle of thermal expansion and long-term trend to downslope of few millimeters per year. The presence of continuous monitoring solution, could be an essential help to better understand the kinematics of unstable slope and to recognize the beginning of a possible paroxysm phase that could end with a failure of the unstable area. We tested the accuracy of the instruments and the first year of experimental measurements are presented. We also propose a methodological approach that considers the use of automatized procedures for the identification of anomalous trends and a risk communication strategy based on monitoring data.

Engineering properties of bedrock materials at Badlands National Park were used to develop models for Park managers to assess slope erosion and stability for fossil resource protection. Six fully instrumented sites were used to document slope conditions. Bedrock consisted of Oligocene White River Group rocks. Bulk erosion rates correlated to grain size with silty-sandy materials producing higher mass erosion rates as a function of the silt-to-clay ratio and plastic index. Data indicated that as grain size decreased, plastic index increased leading to a decrease in erodibility. These parameters were used to construct a grain-size proxy, ψ, that was substituted for grain size, D, in Bagnold’s entrainment equation and provided significant improvement in calculation of critical entrainment velocities for fine-grained materials. Hydraulic analyses of slope and pediment surface processes indicated surface roughness was a controlling factor and materials washed from rough steep slopes were effectively transported across smooth low-angle pediments with slope-to-pediment angle ratios of nearly 6:1. Slope stability modeling of ten slopes produced high factors of safety for all slopes, even under saturated conditions and was attributable to clay cohesion. All results were used to construct models that predicted years until net slope erosion equaled 2.5 cm (1 inch). Using these results, Park managers were advised to visit erosion-prone sites on a 1 to 6 year schedule, based on site geology and slope aspect, to adequately protect critical fossil resources from destruction.

Body weight support (BWS) and incline running (IR) are commonly used either during rehabilitation or during training separately, with many positive effects on athletes’ performance and rehabilitation. The aim of this study is to investigate the effect of BWS and IR. In eighteen healthy men (age: 20.3 ± 1.2 yr, body weight: 70.2 ± 4.8 kg, body height: 179.6 ± 5.4 cm), the changes in electromyographic activity (EMGA) during a 10-min run with BWS (15% or 30% of body weight; in different occasions) and IR at 7%, as well as jumping performance and gait spatiotemporal parameters were evaluated. Lower Rating of Perceived Exertion and a significant decrease in VL (33,4%), SOL (17%), and GL EMGA (28.5%, p &lt; 0.05) but not in GM (10.5%, p &gt; 0.05), were observed during BWS30% at 7% slope compared to flat running. Also, low-frequency fatigue of the quadriceps was induced only after running without BWS at 7% slope (P = 0.011). No changes were found in jumping performance (p = 0.246) and gait spatiotemporal parameters (p &gt; 0.05) except for flight time (p &lt; 0.006). In conclusion, compared to normal flat running, BWS reduces electromyographic activity and fatigue during slope running.

For embankment slope stability, soil cohesivity is one of the most important shear strength parameters. The effect of cohesiveness on the slope stability of a homogeneous embankment dam under rapid drawdown loading conditions was examined in this study. With the use of numerical modeling in GeoStudio, different situations were explored based on cohesiveness (0 kN/m², 5 kN/m², 10 kN/m^2, and 15 kN/m²) under a 1 m per day drawdown rate. The factor of safety value obtained from the long-term steady-state condition under 15 kN/m² cohesion was equivalent to a 116.8% increase from the one obtained under 0 kN/m² cohesion. The factor of safety values obtained after subjecting the embankment to different soil cohesion levels yielded a p-value of 1.91 x 10^-41, according to the Analysis of Variance. The calculated p-value (alpha value) is less than 0.05, suggesting that the differences between the examined cohesiveness values based on the list of the factor of safety values are statistically significant. The findings derived in this study show that it is significant to capture the effect of material characteristics during the design phase of an embankment dam.

Monitoring of the surface operations using movement and surveying radar (MSR) can prevent loss of life, equipment, production and loss of the mine. Slope monitoring using MSR is an important aspect of open-pit mining as it provides real-time movement of deformation data for the slope. It is therefore important that the radar is accurately geo-referenced in order to provide accurate real-time movement data. Geo-referencing is defined as the process of determining an instrument’s position (in the form of Easting, Northing, Height) as well as the orientation with respect to the mine’s local coordinate system. This helps in getting geo-referenced data points from the radar that are identified by a unique set of coordinates in relation to the mine’s coordinate system which allows the radar to track movement for a specific set of coordinates. In this research, we assess the performance of geo-referencing a radar using the total station method and compare it with the integration of Advance Navigation – Spatial Dual GPS system connected via RS422 on the MSR. This includes usage of the Spatial Dual navigation coordinates output to calculate the radar’s position relative to the mine local coordinates and mapping the radar’s azimuth, elevation and Range (Az, El and Rl) values to the measured pit-slope data points. Furthermore, a comparison of key attributes of both methods of geo-referencing is performed using a matrix system and giving an overall performance appraisal of both systems. Integrating a navigation system allows the radar to have an auto geo-referencing functionality that will reduce the time spent in completing this process. The findings reveal that the GPS obtained a higher score than the total station with prism method on the weighted matrix system. The total station was found to be more accurate than the GPS however, the deployment time for the GPS is quicker than that of the total station. This is important for different operation such as strip and open-pit mining to choose the preferred method of geo-referencing depending on the level of accuracy required.

Wave is a common environmental load that often causes serious damages to offshore structures. In addition, the stability for the submarine artificial slope is also affected by the wave loading. Although the landslide of submarine slopes induced by the waves has received wide attention, the research on the influence of solitary-wave is rare. In this study, a 2-D integrated numerical model is developed to investigate the stability of the foundation trench under the solitary wave loading. The Reynolds-Averaged-Stokes (RANS) equations are used to simulate the propagation of a solitary wave, while the current is realized by setting boundary inlet/outlet velocity. The pore pressure induced by the solitary wave is calculated by Darcy’s law and the seabed is characterized by Mohr-Coulomb constitutive model. Firstly, the wave model is validated through the comparison between analytical solution and experimental data. The initial consolidation state of slope under hydrostatic pressure is achieved as the initial state. Then, the factor of stability (FOS) for the slope corresponding to different distance between wave crest and slope top is calculated with the strength reduction method. The minimum of FOS is defined as the stability index for the slope with specific slope ratio during the process of dynamic wave loading. The parametric study is conducted to examine the effects of soil strength parameters, slope ratio and current direction. At last, the influence of upper slope ratio in a two-stage slope is also discussed.

The paper presents a three-dimensional slope stability limit equilibrium solution for translational, planar failure modes. The proposed solution uses Bishop’s average skeleton stress combined with the Mohr – Coulomb failure criterion to describe soil strength evolution under unsaturated conditions while its formulation ensures a natural and smooth transition from the unsaturated to the saturated regime and vice versa. The proposed analytical solution is evaluated by comparing its predictions with the results of the Ruedlingen slope failure experiment [1]. The comparison suggests that despite its relative simplicity the analytical solution can capture well the experimentally observed behaviour and highlights the importance of lateral resistance consideration together with a realistic interplay between mechanical parameters (cohesion) and hydraulic (pore water pressure) conditions.

Power converters with coupled inductors are very promising due to the high efficiency and high voltage gain. Apart from the aforementioned advantages, the boost-flyback converter reduces the voltage stress on the semiconductors. However, to obtain good performance with high voltage gains, the controller must include two control loops (current and voltage), and a compensation ramp. One of the most used control techniques for power converters is the peak current-mode control with compensation ramp. However, in the case of a boost-flyback converter there is no mathematical expression in the literature, to compute the slope of the compensation ramp. In this paper, a formula to compute the slope of the compensation ramp is proposed in such a way that a stable period-1 orbit is obtained. This formula is based on the values of the circuit parameters, such as inductances, capacitances, input voltage, switching frequency and includes some assumptions related to internal resistances, output voltages, and some other electrical properties related with the physical construction of the circuit. The formula is verified numerically using the saltation matrix and experimentally using a test circuit.

The There are many factors influencing the performance of photovoltaic (PV) systems. Among these factors, temperature and solar radiation are two major parameters that have a large effect on the efficiency of PV systems. The cell temperature of PV panels is related to the ambient temperature while the solar radiation incident on the surface of the PV modules depends on the slope and azimuth of these modules. Furthermore, ground reflectance (albedo) affects the irradiance incident on the PV panel surface, which in turn affects the output of a PV system. Nevertheless, the effects of these factors on the economic performance of the solar PV systems are scarcely reported. This paper presents a complete design of a stand-alone PV/battery system to supply electric power for a mobile base station in Choman, Erbil, Iraq. The effects of different factors on the total electricity produced by PV arrays and its economic performance are simultaneously investigated. HOMER software has been used as a tool for the techno-economic and environmental analysis. As indicated from the simulation results, the PV array capacity and its economic performance are highly affected by the variation of the slope and azimuth. With a base case (albedo of 20% and average annual ambient temperature of 11°C), the best feasible system which is achieved by facing PV due to south with a tilt angle of 40° or 45°, is found to have net present cost (NPC) of 70595 $ and cost of energy (COE) of 0.54 $/kWh. Moreover, the results indicate that increasing the ground reflectance from 10% to 90% results in a 7.2% decrease in the PV array capacity and about 3% decrease in the NPC and COE. On the other hand, increasing the ambient temperature from 0°C to 40°C results in a 19.7% increase in the PV array capacity and an 8.2% increase in the NPC and COE. Furthermore, according to the ambient temperature of Choman, using PV modules with high sensitivity to temperature is found to be an attractive option. Provided simulation performance analysis proves that the studied parameters must be treated well to establish an enabling environment for solar energy development in Iraq.

The current deformation and stable state of slopes with historical shatter signs is a concern for engineering construction. Suspected landslide scarps were discovered at the rear edge of the slope of the Genie in the Sichuan-Tibet transportation corridor during a field investigation. In order to qualitatively determine the current status of the surface deformation of this slope, this paper uses high-resolution optical remote sensing, airborne LiDAR and InSAR technologies for comprehensive analysis. The interpretation of high-resolution optical and airborne LiDAR data revealed that the rear edge of the slope exhibits three levels of scarps. However, no deformation was detected with the D-InSAR analysis of ALOS-1 radar images from 2007 to 2008 or with the Stacking-InSAR and SBAS-InSAR processing of Sentinel-1A radar images from 2017 to 2020. A geological model of the slope was established in combination with field investigation stipulating that the slope is composed of steep anti-dip layered dolomite limestone and that the scarps at the rear edge of the slope were caused by historical shallow toppling. Further research is recommended to determine the extent of toppling deformation and evaluate the slope stability under the disturbance of tunnel excavation.

The extraction of roof feature lines is an important foundation for realizing large-scale and batch 3D modeling. However, the current traditional point cloud segmentation algorithms do not have satisfactory results in extracting roof feature lines of Chinese traditional residential buildings. In this paper, taking Jingping Village in Western Hunan as an example, we propose a method that combines multiple algorithms based on slope segmentation of roof patches to extract feature lines. Firstly, VDVI and CSF algorithms are used to extract the building and roof point cloud based on the MVS point cloud. Secondly, according to roof features, village buildings are classified, and 3D roof point cloud is projected into 2D regular grid data. Finally, the roof slope is segmented via slope direction, and internal and external feature lines are obtained after refinement through Canny edge detection and Hough straight line detection. Results reveal that this method effectively extracts feature lines of low-building roofs in traditional villages, with slope-based roof surface segmentation accuracy surpassing 99.6%. This method significantly outperforms the RANSAC algorithm and region segmentation algorithm.

A method for studying properties of the earth's surface tremor, measured by means of GPS, is proposed. Four characteristics of tremor are considered: the entropy of the distribution of wavelet coefficients, the Donoho-Johnston wavelet index, and two estimates of the spectral slope. The anomalous areas of tremor are determined by estimating the probability densities of extreme values of the studied properties. The criteria for abnormal tremor behavior are based on the proximity to, or the difference between, tremor properties and white noise. The greatest deviation from the properties of white noise is characterized by entropy minima and spectral slope and DJ index maxima. This behavior of the tremor is called "active". The "passive" tremor behavior is characterized by the maximum proximity to the properties of white noise. The principal components approach provides weighted averaged density maps of these 2 variants of extreme distributions of parameters in a sliding time window of 3 years are considered. Singular points are the points of maximum average densities. The method is applied to the analysis of daily time series from a GPS network in the West USA in 2009-2022. It turned out that singular points of tremor form well-defined clusters.

A method for studying properties of the earth's surface tremor, measured by means of GPS, is proposed. Four characteristics of tremor are considered: the entropy of the distribution of wavelet coefficients, the Donoho-Johnston wavelet index, and two estimates of the spectral slope. The anomalous areas of tremor are determined by estimating the probability densities of extreme values of the studied properties. The criteria for abnormal tremor behavior are based on the proximity to, or the difference between, tremor properties and white noise. The greatest deviation from the properties of white noise is characterized by entropy minima and spectral slope and DJ index maxima. This behavior of the tremor is called "active". The "passive" tremor behavior is characterized by the maximum proximity to the properties of white noise. The principal components approach provides weighted averaged density maps of these 2 variants of extreme distributions of parameters in a sliding time window of 3 years are considered. Singular points are the points of maximum average densities. The method is applied to the analysis of daily time series from a GPS network in the West USA in 2009-2022. It turned out that singular points of tremor form well-defined clusters.

Application of the Ramsey Theory to the set of the points placed in the plane is discussed. Consider a set of N points located in the same plane. The straight lines connecting these points are yikx=αikx+βik i,k=1...N. Listed below values of slopes αik are possible: αik&gt;0; αik=0; αik is not defined; αik&lt;0. Following coloring procedure is introduced: we connect the pairs of points for which αik&gt;0, αik=0 or αik is not defined, with the red links, and the pairs of points for which αik&lt;0 place with green links. The suggested coloring procedure enables building of the complete bi-colored graph for any set containing N points located in the same plane. We apply the Ramsey theorem to the complete graph emerging from the suggested coloring. For the set containing N=6 points at least one monochromatic triangle will necessarily appear in the graph. The values of the slopes αik depend on the chosen coordinate system. The rotation of coordinate axes changes the coloring of the graph; however, at least one monochromatic triangle will be present for N=6. The introduced coloring procedure diminishes the order of the symmetry group of the regular hexagon, irrespectively to the orientation of the coordinate axes. We hypothesized that this will be true for arbitrary regular n-polygon, independently on the orientation of coordinate axes. The inverse bi-color Ramsey graphs arise, when we replace red links appearing in the source graph with red ones, and vice versa. The total number of triangles in the “direct” and “inverse” Ramsey graphs is the same. We considered the particular case of the set of points for which αik&gt;0 or αik&lt;0 is true in the given coordinates. In this particular case, the rotation of the Cartesian coordinate axes to the angle θ=π2 yields the inverse complete graph. Generalization of this coloring for an arbitrary number and arbitrary location of the source points is introduced.

High-precision ground point cloud data has a wide range of applications in various fields, and the separation of ground points from non-ground points is a crucial preprocessing step. Therefore, designing an efficient, accurate, and stable ground extraction algorithm is of great significance for improving the processing efficiency and analysis accuracy of point cloud data. The study area in this article was a Park in Guilin, Guangxi, China. The point cloud was obtained by utilizing the UAV platform. In order to improve the stability and accuracy of the Filter algorithm, this article proposed a triangular grid filter based on Slope Filter, found violation points by the spatial position relationship within each point in the triangulation network, improved KD-Tree-Based Euclidean Clustering, and applied it to the non-ground points extraction, this method has good accuracy, stability and achieves good results in separating ground points from non-ground points. At first, using Slope Filter to remove some non-ground points, to reduce the error of taking ground points as non-ground points; Secondly, established a triangular grid based on the triangular relationship between each point, the violation-triangle can determin through the grid, and then the corresponding violation points were found in the violation-triangle; Thirdly, according to the three-point collinear method to extract the regular points, used these points to extract the regular landmarks by KD-Tree-Based Euclidean Clustering and Convex Hull Algorithm; Finally, removed disperse points and irregular landmarks by Clustering Algorithm. In order to confirm the superiority of this algorithm, this article compared the filter effects of various algorithms on the study area and filtered the 15 sample data provided by ISPRS, and obtained an average error of 3. 46%. The results showed that the algorithm in this article have a high processing efficiency and accuracy, which can greatly improve the processing efficiency of point cloud data in practical applications.

Hillslope and mountain roads are often the source of erosion, which in turn can lead to larger landslides and other types of mass-movements. For this reason, low-cost repeat surveys that can be done by practitioners and not solely scientists and engineers is essential. To solve this issue the present contribution shows the testing and applicability of a mix of SfM-MVS and low-cost SLAM technology to provide erosion information. The low-cost SLAM generated between 300 ~ 900 points per square meter, while SfM-MVS created between ~11,000 to 900,000 points. The density is however a trade-off against a spatially varying error, although the variability at the road-cut scale only ranges from 2 cm vertically to 2.5 cm in x,y,z based on the C2C algorithm. Furthermore, this error tends to be more important in the higher section of the cutout (further away from the sensor and at a flatter angle). It is thus possible to measure small-scale roadside change, providing that the change is in the range of >5 cm (adding the maximum potential error twice) and providing that the road-cut is such that the sensors can be brought close to the surface (camera or sensor on a pole). The authors suggest that it can be a solution for state and agencies with limited funding and that cannot afford regular laser or for roadside that are difficult to access.

In the context of high frequency and intensity forest fires driven by future warming and drying climate, early detection and effective control of fires are extremely important to reduce losses. Satellite remote sensing, characterized by its broad observational scope and strong repeat observation capability, has become an important method for rapid monitoring of forest fires, replacing traditional means such as manual measurement and aerial photography. This paper addresses the misjudgments caused by solely relying on changes in infrared band brightness values and single-band separation in forest fire discrimination. It constructs the angle slope index ANIR based on the red band, near-infrared band and short-wave infrared band, Angle slope index AMIR based on the short-wave infrared band, mid-infrared band and far-infrared band, and angle slope index AMNIR based on the difference between the AMIR and ANIR, integrating the strong inter-band correlations and the reflectance characteristics of visible and short-wave infrared bands to simultaneously monitor smoke and fuel biomass changes in forest fires. To address the omissions caused by single-image fire discrimination algorithms, the paper constructs time-series Angle slope difference indices ∆ANIR and ∆AMIR. To address the different fire point discrimination thresholds caused by background difference in different time and space, the paper uses the decomposed three-dimensional OTSU(Maximum inter-class variance method) algorithm to calculate the segmentation threshold of the sub-regions constructed from the AMNIR data. The methods were validated using high temporal resolution meteorological satellite Himawari-8 and ground truth fire data from Hunan Province, China, from 2018-2019. The results show that the discrimination method based on the ASITR(Angle slope indices thresholds) method exhibits an accuracy of 0.88, a missed detection rate of 0.17, and an overall evaluation value of 0.85, which is 0.09 higher in accuracy and 0.03 higher in overall evaluation than the discrimination method based on infrared bands brightness values proposed by Feng et al. [1] (accuracy 0.79, missed detection rate 0.14, overall evaluation value 0.82); the method based on the FAMN_OTSU_ASITR (Fusion of Angle slope difference index (false) data, Decomposed three-dimensional OTSU adaptive threshold segmentation Algorithm and ASITR) exhibits an accuracy of 0.85, a missed detection rate of 0.08, and an overall evaluation value of 0.88, which is 0.09 lower in missed detection rate and 0.03 higher in overall evaluation as compared to the ASITR. The results demonstrate that the forest fire discrimination method based on Angle slope indices, Himawari-8 satellite data, and the decomposed OTSU adaptive threshold segmentation algorithm can improve the accuracy of forest fire discrimination and reduce errors in missed detections.

In this study, the effects of grain size and gradation of riprap, overtopping flow depth and downstream slope of embankment on scouring and deposition characteristics at the downstream toe of the embankment was investigated. For the experiment, three different downstream slopes (1:2, 1:3, and 1:4), three different overflow depths (1, 2, and 3 cm), and three different sizes (d₅₀ of 16.41 mm, 8.48 mm, and 3.39 mm herein referred as No.5, 6 and 7 respectively) of riprap particles, respectively, were used in the laboratory. The experimental results demonstrated that the scour depth and deposition height increased with increasing energy head for each downstream slope condition. Among the three particle sizes, for No. 5 size particle shows the lowest scour depth and highest deposition height. For the 1:2 slope, the No. 5 particle size could resist scour 62% and 75% less than that of the No. 6 and No. 7 particles, respectively. For the 1:3 slope case, this was 31% and 46%, and for the 1:4 slope case, this was 39% and 49% less than the No. 6 and No. 7 size particles, respectively.

In the present study we examine the relationship among sovereign yields, temperature and precipitation using a large monthly panel data set which consists of 20 eurozone members, over the period 1980M1 – 2023M4. To account for possible asymmetries along the distribution of the climate variables we assume a quadratic modelling specification and apply various mean panel estimation techniques of heterogeneous coefficients. At a next step, to consider possible nonlinearities in the distribution of the dependent variable (sovereign yields), we apply the quantile via moments methodology of Machado and Santos Silva (2019), which accounts for possible cross-sectional dependence and slope heterogeneity. We contribute to the existing literature in two main ways. First, by applying a quantile methodology that provides a more in-depth analysis of the climate effects along the distribution of the sovereign yields, especially in the presence of non-normally distributed data. Second, we find that climate change, as proxied by higher temperatures or lower precipitation (drought), will increase the sovereign risk of all countries, but the magnitude of the impact will be higher for countries that are already characterized by higher sovereign risk levels and/or face extreme weather conditions (hotter countries and/or countries with low levels of precipitation).

As a new plant slope protection technology, living stumps can effectively improve slope stability. The current study attemptes to investigate the mechanical characteristics of the root system of living stumps and their reinforcement mechanism on slopes by carrying out a three-dimensional living stump slope modeling test. Using ABS materials, a 3D model of a living elm stump was created by 3D printing and a slope model test was carried out. The reinforcement mechanism of the living stump was studied through a combination of model testing and numerical simulation. The results indicate that, due to the presence of living stumps in the lower and middle parts of the slope, the maximum shear stress area of the soil moved to a deeper direction. The stress state of the soil around the living stump was effectively improved due to the existence of the lateral root system.Living stumps in the lower part of the slope cross the potential sliding surface and transferred the soil shear stress gradually to the root system through root-soil interaction. Moreover, the tap roots and lateral roots of living stumps form a robust spatial structure that bears the shear stress of soil together, thus increasing the stability of the slope.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Keywords: Mandra flash flood, soil erosion, slope failure, RES, mitigation measures, landslide susceptibility

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

Groundwater plays a crucial role in triggering and reactivating deep-seated landslides. However, classical hydrogeological investigations have limitations in their applicability to deep-seated landslides due to anisotropic and heterogeneous media[16]. The Huangtupo landslide in the Three Gorges reservoir area has garnered significant attention in China due to its large volume, complex geological structure, and high hazard potential. Recent monitoring data has shown notable deformation in the NO.1 Riverside Sliding Mass (HTP-1), one of the four parts of the Huangtupo landslide, making it the primary focus of landslide research. This study aimed to investigate the water sources in the HTP-1 landslide using environmental stable isotopes as tracers. The isotopic analysis results indicated that the groundwater in the landslide area (LGW) is a mixture of remote karst groundwater (KGW) from the adjacent up-slope and local precipitation (LP). The karst groundwater is a major contributor to the recharge of the landslide groundwater system, causing a high slope groundwater level that can easily exceed the critical level during heavy rainfall events. Furthermore, based on the differential distribution of the LP fraction of LGW at different locations, the groundwater in the landslide can be classified into three groups. Groundwater at the sliding rupture surface has the highest fractions of local precipitation, followed by the groundwater at the rear of the landslide. Combined with the monitoring data of groundwater level in boreholes during the rainy season, this indicates that fissures and fractures in the sliding rupture zone and at the back of the landslide are well connected, which could be a critical factor in the mass movement of the creeping slope.

This article reveals a best possible design for hybrid dispersion compensating fiber (HyDCF) with high birefringence established on modified broadband compensating structure through S, C and L telecommunication bands. The simulation outcome exhibits relatively higher birefringence of 3.76×10-2 at wavelength of 1550 nm. The suggested fiber also has dispersion compensation characteristics in an inclusive series of wavelengths which covers 1400-1625 nm. The reported design can achieve dispersion quantity of – 606 ps/ (nm.km) at 1550 nm effective wavelength. The reported fiber design matches the relative dispersion slope (RDS) 0.003694 nm-1 similar to single mode fiber at 1550 nm operating wavelength. This fiber demonstrates negatively flattened effective dispersion of – 2.703 ± 0.734 ps/ (nm.km) within 180 nm flat band ranging from 1460-1640 nm wavelength. It is also convenient to optical high bit rate communication systems. The low confinement loss is found 3.756×10-10 dB/m at the operating wavelength. This design also achieves highly nonlinear coefficient of 50.34 W-1km-1. In some cases, it can also be used in sensing applications.

The acquisition of high resolution morpho-bathymetric data on the Calabro Tyrrhenian continental margin (Southern Italy) enabled us to identify several mass-wasting processes, including shallow gullies, shelf-indenting canyons and landslides. In particular, we focus our attention on submarine landslides occurring from the coast down to -1700 m, with mobilized volumes ranging from some hundreds up to tens of millions of cubic meters. These landslides also show a large variability of geomorphic features in the headwall, translational and toe domain. Based on their morphology and distribution, four main classes of coastal/submarine landslides have been recognized: a) rocky coastal/shallow-water failures characterized by large hummocky deposits offshore; b) large-size and isolated scars with associated landslide deposits, mostly occurring on open slope environment and lower part of tectonically-controlled escarpments; c) a linear array of coalescent and nested landslide scars occurring in the upper part of tectonically-controlled escarpments and canyon flanks; d) a cauliflower array of small and coalescent scars occurring in canyon headwall. The latter two classes of landslides are also characterized by a marked retrogressive evolution and their landslide deposits are generally not recognizable on the morpho-bathymetric data. By integrating the morpho-bathymetric dataset with the results of previous studies, we also discuss the main factors controlling the variability in size and morphology of these submarine landslides to provide insights on their failure and post-failure behavior.

In the paper, the author discusses and computes bounds of the sine and cosine along straight lines on the complex plane.

The evaluation of landslide hazard in seismic areas is based on a deterministic analysis to define the stability of the sites. However, deterministic analysis is not able to consider various uncertainties in the analysis process. This paper focuses on the results established by the probabilistic seismic hazard analysis and extends the probabilistic landslide hazard analysis to consider the uncertainties of opposing ground deformations and strength. The work studies the areas between Nibbiano and Sant'Erasmo inhabited centres in the Camerino municipality located in central Italy. The current state of the areas shows dangerous conditions for the building structures. In fact, all constructions present evidence of damage caused by both the 2016 earthquake and slope instability. The studies, carried out through careful geological survey and detailed geophysical investigations, are performed to define the geological, geomorphological and hydrogeological characteristics of the areas and also to run a new analysis aimed to define the material stress-strain behavior. Both inhabited Centers are located on debris deposits with highly variable thicknesses. The key point regards the definition of the depth of unstable mass, its position and its extension. Therefore, this contribution aims to summarize the knowledge of the landslide phenomenon that affected the area, trying to interpret its evolution with new field investigations. Indeed, during the first step, related to the geological and geomorphological detailed surveys, a remarkable geological model was obtained to better interpret the slope dynamics in relation to the structures of this section of the ridge. This model was also confirmed by the geophysical investigations. The study involves a more detailed definition of the landslide perimeter. Indeed, to analyze the phenomenon, it was necessary to study both the local seismic amplification with finite element 2D simulations and the slope stability conditions with finite 3D difference simulation.

Rapid draw-down in an earthfill dam has serious implications for dam safety regarding slope stability. The evaluation of reservoir draw-down impact on slope stability was carried out considering the case study of 8 hours of rapid draw-down of the Middle Marsyangdi Hydroelectric Power Project (MMHPP) rock-fill dam using the Limit Equilibrium Method (LEM) and stress-based Finite Element Method (FEM). The time-dependent factor of safety (FOS) was evaluated and found that the 8 hours of rapid draw-down undertaken in October 2012 for reservoir flushing was unsafe with a draw-down rate of 1.91m/h. The resulting FOS of 1.28 and 1.27 using LEM and FEM was classified as unsafe as per the US Army Corps of Engineers’ guideline, the minimum required factors of safety should be greater than 1.3. The minimum safe allowable draw-down rate of 0.76m/h for 20 hours was identified. Applying three layers of horizontal filter materials and increasing the upstream dam’s permeability provided adequate FOS results for all cases by increasing seepage discharge to reduce the destabilizing excess pore water pressure. Several gradual draw-down rates were also tested and found that FOS increases with decreased draw-down rates, as it reduces the excess pore water pressure controlled with stabilizing existing water load.

In several Indonesian tropical cities, such as Makassar City, frequent flooding during the peak rainy season poses a significant challenge. This study seeks to address this issue by devising effective policies to reduce flood exposure. The main obstacle lies in accurately determining the flood inundation area. To overcome this, the study utilizes multiple satellite data sources on a cloud platform, integrating them with land use data, and DEM data, aligning these with the local government's urban land use plan and existing drainage networks. The research aims to quantify the affected area, identify the predominant inundated land cover, and assess the efficiency of Makassar's drainage system and urban land use plan. The study reveals that an uncoordinated drainage system in the Tamalanrea, Biringkanaya, and Mangala sub-districts results in severe flooding, encompassing a total area of 35.28 km². The most affected land use type is cultivation, constituting approximately 43.5% of the flooded area. Furthermore, 82.26% of the urban land use plan, covering 29.02 km², is submerged. It is imperative for the local government and stakeholders to prioritize the enhancement of drainage systems and urban land use plans, particularly in low-lying and densely populated regions

With more and more transportation tunnels have been and will be constructed in loess areas in Northwest China with high earthquake potential, the overall stability of portal section under earthquakes actions and the related aseismic countermeasures attracted the attentions from both the scholars and engineers, especially the tunnels in the upper slope connecting the high bridges crossing rivers or valleys. In order to study the dynamic response characteristics and damage evolution of steep loess slope with a tunnel under the earthquake actions, a large-scale shaking table tests were performed on steep loess slope with a tunnel. Wenchuan-tangyu (WT) wave and El Centro (El) wave records were applied on the model to investigate the displacement response and acceleration response of loess slope with a tunnel under the horizontal (X) and the combined action of horizontal and vertical (X-Z) seismic loads, respectively. In particular, three-dimensional non-contact optical measurement techniques were used to obtain the slope surface displacements. The results showed that the main deformation pattern of the slope was horizontal movement and settlement when the seismic wave input was in the X and X-Z directions, respectively. However, the X direction seismic wave had a greater impact on the deformation of the slope, and the tunnel portal slope was destroyed under the action of a large horizontal seismic acceleration finally. Slope failure ahead of a tunnel could be divided into four stages, i.e. elastic deformation stage, plastic deformation accumulation stage, local failure stage, and overall failure stage. The peak ground displacement of X direction (PGDX) and peak ground displacement of Z direction (PGDZ) of the slope surface increased with the increasing of the input peak ground acceleration (PGA) when the input wave was same waveform and same direction. The existence of the tunnel had a great influence on the PGA and the PGA amplification factor (PGAAF) of the soil mass surrounding it. This was because the seismic waves encounter a tunnel surface with clear differences in the physical properties of the medium during their propagation in the slope, thereby forming a strong reflection and refraction effect, and the amplitude changed significantly. Numerical simulation results were basically consistent with the experimental results.

The eutrophication caused by excessive total nitrogen(TN) and total phosphorus(TP) emissions has been widely concerned by the whole society. Studies have revealed the relationship between land use and TN and TP, but the relationship between land use compound topographic position and TP and TN was seldom studied. Therefore, Spearman correlation and redundancy analyses were used to reveal the relationship between land use compound topographic position and TN and TP based on the monthly data of 28 water quality sampling sites and the land use data of 2013 and 2016 in the lakes of Guizhou Plateau. The results show that the nutritional state of the HBA watershed is medium. The trophic level index (TLI) value and TN concentration were high during flood, while TP concentration was high in dry period. The TN concentration in the tributaries was higher than that in the reservoir area. Construction and valley were the sources of the pollution, whereas forest land and gentle slope were the sink. According to the”source-sink”effect, the optimal zoning of land use was completed, and the urban land pollution govern area should be strengthened firstly. This paper can provide decision support for water environment management and sustainable development decision-making.

An experimental series of shearing tests with water infiltration were performed on compacted unsaturated soil to simulate the behavior of shallow slope failures. Soil samples were compacted at moisture contents from dry to wet of optimum moisture content with the degree of saturation varying from 24.0% to 59.5% while maintaining the degree of compaction at 80%. Two series of shearing with infiltration tests were performed in this study. In Series-I, just before the start of shearing, matric suction was decreased by increasing pore water pressure to start water infiltration i.e. shearing is carried simultaneously with water infiltration. In Series-II, the soil was first sheared with drained pore air and undrained pore water to pre-defined value of deviatoric stress, after which matric suction was decreased by increasing pore water pressure to start water infiltration and shearing is performed by keeping deviatoric stress constant on the specimen. The test results showed that the decrease in matric suction has an effect on the volume of infiltrated water and degree of saturation. The soil slopes compacted on the dry side of optimum moisture content showed better performance than other soils, they require more decrease in matric suction to start water infiltration and showed higher deviatoric stress. In addition to this, water infiltration alone can cause the failure of shallow slopes without having to have any further loading.

Cascading landslides represent a dynamic and hazardous geological phenomenon, char-15 acterized by a sequential chain of slope failures triggered by various factors such as heavy rainfall, 16 seismic activity, or anthropogenic activities. These events can amplify the damage caused by the 17 initial trigger and propagate instability along a slope, often resulting in significant environmental 18 and societal impacts. The Morino-Rendinara cascading landslide, situated in the Ernici mountains 19 along the border of Abruzzo and Lazio region (Italy), serves as a notable example of the complexities 20 and devastating consequences associated with such events. In March 2021, a substantial debris flow 21 event in Morino obstructed the Liri River, marking the latest step in a series of landslide events 22 characterized by a complexity far beyond initial expectations. This study employs a multidiscipli-23 nary approach, combining conventional techniques and advanced technologies, to understand the 24 complexities of the Morino-Rendinara landslide. Field activities, UAV image acquisition, SAR inter-25 ferometry based on SENTINEL-1 images and pixel offset analysis based on high-resolution Google 26 Earth images, offer insights into the geological and hydrogeological setting of the unstable slope, 27 landslide geometry, mechanism and kinematics. To supplement the analysis a specific FEM slope 28 stability analyses is used to reconstruct the deep geometry of the system emphasizing the modula-29 tion action of groundwater flow to the slope stability

The thermal degradation of brakes has a significant impact on the stability of pure electric commercial vehicles during long downhill braking. Based on road slope and using fuzzy control method, design strategies for motor regenerative braking force and friction braking force distribution, with the aim of reducing friction braking force, improving braking stability, and recovering braking energy. By establishing driving conditions on roads with different slopes and using numerical analysis methods to verify the proposed control strategy. the results show that under the 6% constant slope driving condition, the vehicle maintains a constant speed of 30km/h downhill driving, and the braking energy recovery rate reaches 50.93%; Under the condition of 3% -6% gradient driving, the vehicle speed fluctuates slightly, but it can still be maintained at a constant speed of 30km/h for downhill driving through the adjustment of the motor's reverse drag characteristic, with a braking energy recovery rate of 49.97%; During the process of driving downhill at a constant speed, the frictional braking force does not participate in braking; The braking energy recovery rate is determined by the slope and braking deceleration.

The entry and exit method is a simple and practical method to determine the critical slip surface of slope. However, it has the drawback of sacrificing computational efficiency to improve search accuracy. To solve this problem, this paper proposes an improved entry and exit method to search for the critical slip surface. Based on the random fields generated by using Karhunen–Loève expansion method, the simplified Bishop’s method combined with the improved entry and exit method is used to determine the critical slip surface and its corresponding minimum factor of safety. Then, the failure probability is calculated by conducting Monte Carlo simulation. Two examples are reanalyzed to verify the accuracy and efficiency of the proposed method. Meaningful comparisons are made to demonstrate the calculating accuracy and calculating efficiency of the improved entry and exit method in searching for the minimum safety factor of slope, based on which the effect of the reduced searching range on slope reliability was explored. The results indicate that the proposed method provides a practical tool for evaluating the reliability of slopes in spatially variable soils. It can greatly improve the computational efficiency in relatively high-computational accuracy of slope reliability analysis.

We aimed to provide a comprehensive assessment of exercise physiology of adult Fontan patients (FP) and factors limiting functional capacity (FC). A prospective single-centre study of 37 FP aged ≥16years and 19 healthy-controls (HC), who underwent CPET on cycle-ergometer in February-March 2022. Lung function was impaired in FP, mostly mild restrictive pattern (56.8%). Mean peakVO2 was 21±5.4ml/kg/min, 55% predicted. Morphologically left-single ventricle showed higher peakVO2%predicted (57.4±14.4% vs 43.4±8.1%, p=0.045). A lower peakVO2%predicted was observed in patients with an early flattened and/or descending O2 pulse at maximal exertion (52±14% vs 62±12.5, p=0.04 and 47.6±9% vs 60±14 respectively, p=0.018) and chronotropic insufficiency (53±12% vs 69.8±20%, p=0.008). Strong positive correlation was observed between %OUES and peakVO2%predicted (r=0.726, p>0.001). PeakVO2%predicted was progressively higher as the level of physical activity increased (low-level 49.5±14%, moderate-level 55±12%, intense-level 69±20%). FP showed lower inspiratory muscle strength compared to HC but it was no statistically associated with either peakVO2 or VE/VCO2 slope. In FP OUES is a useful submaximal parameter in those who fail to reach maximal exertion. Chronotropic insufficiency and early flattened or descending oxygen pulse slope were factors associated with low peakVO2. Regular intense physical activity improves FC. Although FP have inspiratory muscle weakness, its impact on FC is unclear.

The Soil Conservation Service - Curve Number (SCS-CN) method is extensively used to calculate the runoff from rainfall over a large catchment over the world. Slope is an important criterion for runoff but a very few attempts have been made to evaluate the effect of slope on the CN with runoff potential. The objective of this paper is to summarise the historical review on the effects of slope on CN and runoff potential in various regions by the hydrologists. This paper also depicts that how the various researchers proved the importance of consideration of slope for CN and runoff estimation. In addition, paper highlights the key features of research in future like to classify the watersheds on slope based CN, accurate Antecedent Moisture Condition (AMC) and proper initial abstraction in the various regions etc. Considering these parameters an accurate runoff estimation can be predicted and managed properly in the urban watersheds.

This study investigates the trend in monthly and annual rainfall, minimum and maximum temperature (T_min and T_max) using the Mann–Kendall (MK) test and Sen’s slope (SS) method and evaluates the significance of their variability for maize, sorghum and millet yields in northern Togo employing multiple regression analysis. The historical data of Kara, Niamtougou, Mango and Dapaong weather stations from 1977 to 2012 were used. Four non-parametric methods—Alexandersson’s Standard Normal Homogeneity Test (SNHT), Buishand’s Range Test (BRT), Pettitt’s Test (PT) and Von Neumann’s Ratio Test (VNRT)—were applied to detect homogeneity in the data. For the data which were serially correlated, a modified version of the MK test (pre-whitening) was utilised. Results showed an increasing trend in the annual rainfall in all four locations. However, this trend was only significant at Dapaong (p < 0.1). There was an increasing trend in T_max at Kara, Mango and Niamtougou, unlike Dapaong where T_max revealed a significant decreasing trend (p < 0.01). Similarly, there was an increasing trend in T_min at Kara, Mango and Dapaong, unlike Niamtougou where T_min showed a non-significant decreasing trend (p > 0.05). Rainfall in Dapaong was found to have increased (7.79 mm/year) more than the other locations such as Kara (2.20 mm/year), Niamtougou (4.57 mm/year) and Mango (0.67 mm). T_max increased by 0.13, 0.13 and 0.32 °C per decade at Kara, Niamtougou and Mango, respectively, and decreased by 0.20 per decade in Dapaong. Likewise, T_min increased by 0.07, 0.20 and 0.02 °C per decade at Kara, Mango and Dapaong, respectively, and decreased by 0.01 °C per decade at Niamtougou. Results of multiple regression analysis revealed nonlinear yield responses to changes in rainfall and temperature. Rainfall and temperature variability affects rainfed cereal crops production, but the effects vary across crops. The temperature has a positive effect on maize yield in Kara, Niamtougou and Mango but a negative effect on sorghum in Niamtougou and millet in Dapaong, while rainfall has a negative effect on maize yield in Niamtougou and Dapaong and millet yield in Mango. In all locations, rainfall and temperature variability has a significant effect on the cereal crop yields. There is, therefore, a need to adopt some adaptation strategies for sustainable agricultural production in northern Togo.

Muon tomography leverages cosmic muons’ exceptional penetration capabilities to reconstruct detailed tomographic images via multiple Coulomb scattering interactions, making it invaluable for detecting High-Z materials critical to homeland security. This study introduces the Slope Intercept (SI) algorithm, a novel approach for rapid and precise tomographic image reconstruction. Implemented using Geant4 simulations in a standard-sized container tomography station, SI demonstrates superior performance in speed and simplicity compared to traditional methods. While the imaging results of SI and the Point of Closest Approach (POCA) algorithm are nearly identical, the SI algorithm is simpler to implement, requires shorter CPU time, and exhibits a smaller margin of error. Its computational efficiency and simplicity make it a robust alternative to the POCA algorithm. These findings highlight SI’s suitability for applications demanding robust imaging and efficient data processing, which are crucial for advancing security measures and scientific research.

In mountain-gorge areas, the rock creep is the critical process for high rock slopes failure. During long-term rock creep, slopes might encounter earthquakes and form further creep after earthquakes. This complex mechanical response process can easily lead to the slope failure. Based on a high rock slope in the Nujiang River Basin, this paper analyzes deformation characteristics and dynamic response characteristics by using FLAC3D software, considering combined effects of multiple earthquakes and long-term creep. Results show that when the amplitude increases, the shear strength of the slope decreases and the risk of instability increases under combined actions of creep and earthquakes. Earthquakes promote the development of creep and induce the accumulation of damage on the slope surface and in the slope. The delayed effect becomes more pronounced as the slope height increases. We need to consider deformation differences of the slope further. The ground motion response on the slope surface is stronger than those in the slope, with the peak occurring at the top of the slope. Earthquakes have a greater impact on the middle and top of the slope surface, where cumulative damage and crack development begin. Reinforcement should be considered in these two places. Vertical earthquake has a great effect on the dynamic response. The phenomenon of slope resonance leads to a larger MPGA in the vertical direction than in the horizontal direction. Nonlinear and damping characteristics of the slope and the frequency of seismic waves cause the MPGA to decrease with the increase of amplitudes. This study could promote the development of high rock slope failure mechanism and provide references for the prevention of landslides in the Nujiang River Basin.

The aim of this research was to analyze the impact of implemented erosion control works (ECW) on soil erosion intensity in the watershed of the Ćelije reservoir (Rasina River) in the period between 1968 and 2022. The Erosion Potential Method was used to calculate the annual gross erosion (W), sediment transport (G), and erosion coefficient (Z) in the study area. As a result of the performed ECW there was a general decreasing trend in the intensity of soil erosion processes in the last 54 years. The specific annual gross erosion was 1189.12 m3/km-2/year-1 in 1968, while in 2022 it was 554.20 m3/km-2/year-1. The specific sediment transport was 540.18 m3/km-2/year-1 in 1968 and 253.55 m3/km-2/year-1 in 2022. Due to the changes in the intensity of erosion processes the specific annual gross erosion decreased by 634.92 m3/km-2/year-1, and the specific sediment transport by 286.63 m3/km-2/year-1. The erosion coefficient was reduced from Z=0.62 to Z= 0.35. A dependence between the slope of siltation and the natural bed slope was defined. The results show a significant correlation between erosion intensity and performed ECW, providing a basis for future watershed management and defining a strategy for soil erosion control in the Ćelije reservoir watershed.

In this paper a new approximate procedure is developed for calculating the inclination angle of the end points of statically determinate beams. The method is based on the topology comparison of simple (hinge-roller combination) supported beam and a resemblant cantilever beam. Assuming that the support reactions of the beam are active forces, the virtual displacements at the points of the reaction forces are calculated. Based on these values the inclination angle is calculated. Several examples are considered and the suggested in this paper, while the procedure is applied for various types of structures and loadings. The results, obtained by the suggested numerical procedure, are compared with analytical ones, and they are in good agreement.

Predictive simulation of concurrent debris flow using only pre-disaster information has proven to be difficult as a result of problems in predicting the location of debris-flow initiation (i.e., slope failure). However, because catchment topography has concave characteristics, with all channels in a catchment joining each other as they flow downstream, it is possible to predict damage to downstream area using relatively inaccurate initiation points. Based on this, this paper presents methodologies employing debris-flow initiation points generated randomly using statistical slope failure prediction. A many-case simulation across numerous initiation points was performed to quantify the effect of slope-failure location in terms of deviations in the predicted water level and terrain deformation. It was found that the relative standard deviation diminished as the points approached the downstream area, indicating a location-based predictability effect.

UAV photogrammetry development during the last decade has allowed to catch information at a very high spatial and temporal resolution from terrains with very difficult or impossible human access. This paper deals with the application of these techniques to study and produce information of very extreme topography which is useful to plan works on this terrain or monitoring it over the time to study its evolution. The methodology stars with the execution of UAV flights on the cut slope studied, one with the cam vertically oriented and other at 45º respect that orientation. Ground control points (GCPs) and check points (CPs) were measured for georeference and accuracy measurement purposes. Orthophoto was obtained projecting on a fitted plane to a studied surface. Moreover, since a digital surface model (DSM) is not able to represent faithfully that extreme morphology, information to project works or monitoring it has been derived from the point cloud generated during the photogrammetric process. An informatics program was developed to generate contour lines and cross sections derived from the point cloud, which was able to represent all terrain geometric characteristics, like several Z coordinates for a given planimetric (X, Y) point. Results yield a root mean square error (RMSE) in X, Y and Z directions of 0.053 m, 0.070 m and 0.061 m respectively. Furthermore, comparison between contour lines and cross sections generated from point cloud with the developed program on one hand and those generated from DSM on other hand, shown that the former are capable of representing terrain geometric characteristics that the latter cannot. The methodology proposed in this work has been shown as an adequate alternative to generate manageable information, as orthophoto, contour lines and cross sections, useful for the elaboration, for example, of projects for repairing or maintenance works of cut slopes with extreme topography.

The earth infrastructure is the backbone of the global economy, connecting people, enhancing quality of life, and promoting health and safety. However, its vulnerabilities are becoming apparent due to climate change, mainly through frequent wetting and drying (wd) cycles. This study aimed to assess the impact of controlled w-d cycles on the hydromechanical properties of clayey and silty sand soils and its implications for the performance of a typical flood embankment. Volumetric changes were monitored during the w-d cycles. Soil water characteristic curve (SWCC), saturated hydraulic conductivity (ksat), effective cohesion (c’) and effective angle of internal friction (ϕ’) were measured at 1 and 10 w-d cycles. The results indicated that the 10 w-d cycles decreased the saturated moisture content and a flatter SWCC compared to the 1 w-d cycle for clayey soil. The ksat was also significantly higher at 10 w-d cycles than the 1 w-d cycle for clayey soil. An insignificant difference was found in both SWCC and ksat at 1 and 10 w-d cycles for silty sand soil. The ϕ’ for the clayey soil decreased from 28.5 to 20.1 as the wd cycles increased from 1 to 10, while the c’ remained unchanged at 10 kN/m2. On the other hand, for the silty sand soil, the ϕ’ increased from 34.6 to 37.5 with an increase in w-d cycles from 1 to 10, and the c’ remained constant at 1 kN/m2. Numerical modelling of transient water flow coupled with slope stability analysis revealed the dependence of flood embankment performance on the soil's hydromechanical properties and the flooding duration. These findings underscore the need for proactive measures to mitigate landslide risks in regions prone to frequent w-d cycles, thereby ensuring the safety and resilience of slopes and associated infrastructure.

Sediment cores were collected from a mudflow lobe (80 m water depth) offshore of the Mississippi River’s Southwest Pass in 2017 to better understand the sedimentology near the lobe entraining the SS Virginia shipwreck (sunk by a German U-Boat in 1942) and surrounding Mississippi River Delta Front. Core analyses included 210Pb/137Cs geochronology, granulometry, and X-radiography. Sediment accumulation rates (SAR) calculated from excess 210Pb activity in multicores are 0.22–0.29 cm/yr at seabed depths less than 20 cm and 0.29–0.51 cm/year at depths greater than 20 cm. 137Cs accumulation rates are ~0.15 to ~ 0.37 cm/year since 1954 and 1963 respectively. Sediment accumulation rates from 210Pb and 137Cs geochronology and indicators of relative sedimentation and bioturbation from X-radiographs suggest that rates of sediment accumulation near Virginia have declined since ca. the mid-20th century. This may be explained by the multi-decade downslope mass transport of the mudflow lobe in which the shipwreck is embedded, and decreases in sediment supply delivered offshore from the Mississippi River. Mass-transport calculations of the Virginia lobe derived from core properties and published lobe advection rates suggest downslope mass transport is far higher than sediment resupply from the Mississippi River, consistent with recent studies of delta retreat.

This study investigates the transition from surface to underground mining at the Sepon Gold mine. The stability of surface slopes is assessed prior to commencing underground operations. Stope mining is adopted based on ore body characteristics and geological features. Finite element numerical analysis, employing the Generalized Hoek-Brown criterion, evaluates slope stability for surface slopes and opening stopes. The pit design comprises a 70° slope angle, 20 m height, and 10-15 m safety berm, meeting stability requirements with a factor of safety of 2.46. Underground mining design includes a 62° ore body dip, 50 m thick crown pillar to prevent surface subsidence, and 5 m wide, 5 m high stopes. Sill pillars are left for support after each level excavation. Rock bolts are employed in specific stope areas where is necessary, with continuous monitoring for surface deformation. The study analyzes the influence of stope sizes on pit wall and pit bottom stability, identifying slope failures near the hanging wall close to the pit bottom during underground mining. A slight increase in the displacement zone is observed on the upper crest of the top footwall. Overall, the findings demonstrate successful stability in the transition from surface to underground mining at Sepon Gold mine.

Hyperspectral imaging, a rapidly evolving technique, furnishes exhaustive information on Earth's surface reflectance over an extensive spectrum of wavelengths. We have developed a more precise method for analyzing spectral data by meticulously selecting plant leaf pixels and employing a relative reference approach. This enhanced technique correlates camera pixel values with light intensity, bypassing the need for complex equations and thereby providing clearer insights into vegetation vitality. The findings of this study not only enhance the precision of hyperspectral imaging but also bolster our capability for ecological monitoring and understanding environmental health. A novel algorithm based on the red-edge slope was established to classify images, exploiting the spectral reflectance data gleaned from the hyperspectral Liquid Crystal Tunable Filter (LCTF) camera. Compared with conventional SVM and K-means algorithms, our novel algorithm demonstrated commendable performance, achieving an overall accuracy of 90% with a Kappa Coefficient of 0.86. This comparison highlights the novel algorithm's relative strength and potential for large-scale satellite and drone imagery analysis applications. The advancements facilitated by this research are instrumental in ecological assessments, conservation efforts, and resource management strategies, signaling a leap forward in the era of environmental monitoring and analysis.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

The study focused on two climatic variables i.e. precipitation and stream flow for analysing change in trend of rainfall for the River Ssezibwa Catchment area and stream flow of River Ssezibwa. This Catchment is found in the districts of Mukono and Buikwe in Uganda. In this area agriculture is majorly dependent on rainfall and irrigation on a small scale. However, rainfall occurrence has become unpredictable over the past few years as result of the changes in patterns of weather. This has caused severe effects on the agricultural cropping system as well as caused negative effects on the natural water resources. Stream flow data of 57 years (1960 – 2017) and rainfall data for 35 years (1982 – 2017) on a daily basis was analysed to find out the trend and detect change point. Trend analysis was done by using the non-parametric analysis while the change point detection was carried out by using the Pettit test (1979).Magnitude of trend for the time series data was carried out using Sen’s Slope estimator and Mann – Kendall test was done to determine the trend. Results from the statistical analysis highlighted that; for stream flow the trend was generally positive and change point detected to be in the year 2000 while for rainfall data analysis indicated that the trend was predominantly negative and change point was in the year 1998.

This research examines how rainfall and mining affect the slope damage resulting from the transition from open-pit mining to underground mining. Using unmanned aerial vehicle (UAV), the Huangniu slope of Dexing Copper Mine was fully characterized, and experiments were conducted on rock samples from appropriate sites. First, the mechanical properties of the samples were measured. Then, the parameters of the similarity simulation experiments were derived based on the similarity theory. Subsequently, the rainfall, rock slope, data acquisition and monitoring systems were designed. Finally, the rock mass failure with different slope angles was analyzed, and the deformation and damage patterns under the coupling effect were obtained. The results show that rainfall increases pore water pressure and moisture content. Rainfall and slope-slip water have more impact on the open-pit platform. The pore water pressure values on the upper rock mass rise faster than inside. In the open-pit mining stage, the rock mass shifts slightly to the upper left. In the room mining stage, vertical fractures and goaf sinking occur. The fractures above the mine room form a semi-ellipse. In the pillar mining stage, the overlying rock displacement is evident, and fractures persist. In the continuous pillar mining stage, the overlying rock collapses massively. The 65° slope model is the most damaged, while the 55° slope model is the least damaged. The results also suggest that the UAV guides sample selection.

The determination and classification of seafloor sediment types are crucial for the exploitation of marine resources, construction of marine engineering, and maintenance of marine ecological en-vironments. Automatic classification of seafloor sediment based on acoustic telemetry data is an important method to quickly understand the type of a large range of sediment. Currently, most studies on sediment classification are based on multi-beam backscattering intensity data, which is a relatively single data type. Besides, the low-dimensional details of standard U-Net gradually weaken in the propagation process, limiting the accuracy of sediment classification. Therefore, this study proposes an automatic classification method of seafloor sediment types based on an im-proved U-Net and K-means clustering algorithm, using multi-beam water depth, sub-bottom profile, and sample test data in the Northern Slope of the South China Sea. Six sediment types, including gravelly muddy sand, sand, silty sand, less muddy silt, muddy silt, and silty mud, were identified in the study area. Additionally, the study area was divided into four sedimentary en-vironment zones, including the shelf sedimentary area, the upper shelf slope break sedimentary area, the lower shelf slope break mixed sedimentary area, and the slope deposition area, based on the results of sediment classification and geological background. The sedimentary environment zones were found to be distributed along the trend of the shelf slope break line. The results of this study not only provide an important supplement to the existing classification methods of seafloor sediments but also contribute to the understanding of the sedimentary environment and process of the Northern Slope of the South China Sea.

In India, particularly within its North-Eastern territories, the occurrence of landslides triggered by post-dry period rainfall events is a significant concern, with the phenomena persistently causing extensive damage to both life and infrastructure. Despite the inevitability of such natural disasters, it is understood that the impact they exert can be substantially mitigated through the implementation of pre-emptive measures. Critical to the endeavour of landslide prevention is the application of a spectrum of mitigation strategies, predicated upon a foundational analysis of slope stability to ascertain critical surfaces for intervention. This investigation delves into the dynamics of partially saturated soils, a condition commonly resultant from the prolonged dry periods preceding the monsoonal rains. The study's focal point is an experimental examination conducted on soil samples to assess parameters such as soil matric suction and unconfined compressive strength across varying degrees of saturation and density, alongside performing analyses of slope failure incidents after dry period during the 2017 monsoon in the Lunglei district, Mizoram based on some established data. The Soil-Water Characteristic Curve (SWCC), derived from soil suction measurements employing the ASTM D5298-10 standard, utilizes a contact filter paper method and serves to delineate the moisture transition phases of the slope. To replicate the desiccation of the soil slope after monsoonal rains, a microwave drying technique based on the ASTM standard was employed to prepare unsaturated soil samples for Unconfined Compressive Strength (UCS) testing. The integrity of the slope was evaluated in a temporal context, before and after rainfall events of varied intensities throughout the calendar year, utilizing a blend of numerical modeling and empirical laboratory investigations. The persistence of real onsite slope failures underscores the necessity for a numerical analysis approach to unravel the underlying factors causing slope instability, especially given the absence of prior stability assessments for the landslide in question. An evaluation of SWCC curves, UCS tests on partially saturated soil at different densities and saturation and the utilization of the benchmark data collected in 2017 on the shallow transitional landslide in Lunglei, Mizoram caused by intense monsoonal precipitation, are central key data and information used to carry out this research. Rainfall data for Lunglei, sourced from the Mizoram Meteorological Department, facilitated a real-time monsoonal data-driven numerical analysis. This analysis elucidated the pivotal role of rainfall in inducing slope failure, indicating a marked destabilization of the slope after precipitation events. The implications of these findings are far-reaching, suggesting a foundational basis for the development of an advanced landslide early warning system, thereby enhancing disaster preparedness, and mitigating potential damages.

We propose an asynchronous acoustic chirp slope keying to map bit sequences on single or multiple bands without preamble or error correction coding on the physical layer. Details of the implementation are disclosed and discussed, the performance verified on laboratory scale in a pool measurement, as well as simulated for a channel containing Rayleigh fading and Additive White Gaussian Noise. For time-bandwidth products of 50 in single band mode, a raw data rate of 100~bit/s is simulated to achieve bit error rates below 0.001 for signal-to-noise ratios above -6~dB. In dual-band mode and a data rate of 200~bit/s, this bit error level was achieved for signal-to-noise ratios above 0~dB for time-bandwidth product of 25. The packet error rates follow this behavior with an offset of 1~dB.

Since the beginning of the 21th century, infrared Nd:YVO4 pulsed lasers have been widely applied especially in some actual industrial processes. In the working process of a laser-aided etching device, the “match-head” effect must be effectively controlled by suppressing the first giant pulse for a solid-state Q-switched laser. In the process of optimizing the infrared Nd:YVO4 pulsed laser by adjusting the slope parameters of the radio frequency (RF) modulation to suppress the first giant pulse, it has been come across that some abnormal horizontally polarized emission with a very short time appears before the formal vertically polarized emission when the gate signal is artificially started. Actually, abnormal horizontally polarized emission will bring some unexpected machining traces during the production process and even greater dangers. The experimental results show that with the increase of the slope duration of a RF signal, the existence time of abnormal output horizontal polarized light will be shortened, and the horizontal giant pulse and vertical giant pulse are well suppressed. When the slope duration is greater than 0.18 ms both horizontal and vertical giant pulses will disappear. The horizontal polarized light can be thoroughly suppressed when the slope duration is greater than 13.7 ms. Compared with the method of adding polarizer to eliminate abnormal output horizontal polarized light, this method does not add elements in the laser, ensuring that the laser volume is relatively small, and does not affect the quality of the normal output laser. The research conclusion is thought to be of great practical significance especially for processing transparent materials.

Rainfall variability has resulted in extreme events like devastating floods and droughts which is the main cause of human vulnerability to precipitation in West Africa. Attempts have been made by previous studies to understand rainfall variability over Ghana but these have mostly focused on the major rainy season of April-July, leaving a gap in our understanding of the variability in the September-November season which is a very important aspect of the Ghanaian climate system. The current study seeks to close this knowledge gap by employing statistical tools to quantify variabilities in rainfall amounts, rain days, and extreme precipitation indices in the minor rainfall season over Ghana. We find extremely high variability in rainfall with a Coefficient of variation (CV) between 25.3% and 70.8%, and moderate to high variability in rain days (CV=14.0% - 48.8%). Rainfall amount was found to be higher over the middle sector (262.7 mm – 400.2 mm) but lowest over the east coast (125.2 mm – 181.8 mm). Analysis of the second rainfall season using the Mankandell Test presents a non-significant trend of rainfall amount and extreme indices (R10, R20, R99p, and R99p) for many places in southern Ghana. Rainfall Anomaly Indices show that the middle sector recorded above normal precipitation which is the opposite for areas in the transition zone. The result of this work provides a good understanding of rainfall in the minor rainfall season and may be used for planning purposes.

Retrogressive breach failures or coastal flow slides occur naturally in the shoreface in fine sands near dynamic tidal channels or rivers. They sometimes retrogress into beaches, shoal margins and river banks where they can threaten infrastructure and cause severe coastal erosion and flood risk. Ever since the first reports were published in the Netherlands over a century ago, attempts have been made to understand the geo-mechanical mechanism of flow slides. In this paper we have established that events, observed during the active phase, are characterized by a slow and steady retrogression into the shoreline, often continuing for many hours. This can be explained by the breaching mechanism, as elaborated in this paper. Recently, further evidence has become available in the form of video footage of active events in Australia and elsewhere, often publicly posted on the internet. All these observations justify the new term ‘retrogressive breach failure’ (RBF event). The mechanism has been confirmed in small-scale flume tests and in a large-scale field experiment. With a better understanding of the geo-mechanical mechanism, current protection methods can be better understood and new defense strategies can be envisaged. In writing this paper, we hope that the coastal science and engineering communities will better recognize and understand these intriguing natural events.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.