We theoretically investigate and optimize four-wave mixing (FWM) in silicon nitride (SiN) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. Based on extensive previous measurements of the material parameters of the GO films, we perform detailed analysis for the influence of device parameters including waveguide geometry, GO film thickness, length, and coating position on the FWM conversion efficiency (CE) and conversion bandwidth (CB). The influence of dispersion and photo-thermal changes in the GO films is also discussed. Owing to the strong mode overlap between the SiN waveguides and the highly nonlinear GO films, FWM in the hybrid waveguides can be significantly enhanced. We obtain good agreement with previous experimental results and show that by optimizing the device parameters to balance the trade-off between Kerr nonlinearity and loss, the FWM CE can be improved by as much as ~20.7 dB and the FWM CB can be increased by ~4.4 folds, relative to the uncoated waveguides. These results highlight the significantly enhanced FWM performance that can be achieved in SiN waveguides by integrating 2D layered GO films.

Layered two-dimensional (2D) GO films are integrated with silicon-on-insulator (SOI) nanowire waveguides to experimentally demonstrate an enhanced Kerr nonlinearity, observed through self-phase modulation (SPM). The GO films are integrated with SOI nanowires using a large-area, transfer-free, layer-by-layer coating method that yields precise control of the film thickness. The film placement and coating length are controlled by opening windows in the silica cladding of the SOI nanowires. Owing to the strong mode overlap between the SOI nanowires and the highly nonlinear GO films, the Kerr nonlinearity of the hybrid waveguides is significantly enhanced. Detailed SPM measurements using picosecond optical pulses show significant spectral broadening enhancement for SOI nanowires coated with 2.2-mm-long films of 1−3 layers of GO, and 0.4-mm-long films with 5−20 layers of GO. By fitting the experimental results with theory, the dependence of GO’s n₂ on layer number and pulse energy is obtained, showing interesting physical insights and trends of the layered GO films from 2D monolayers to quasi bulk-like behavior. Finally, we show that by coating SOI nanowires with GO films the effective nonlinear parameter of SOI nanowires is increased 16 fold, with the effective nonlinear figure of merit (FOM) increasing by about 20 times to FOM > 5. These results reveal the strong potential of using layered GO films to improve the Kerr nonlinear optical performance of silicon photonic devices.

Nanoparticle (NP)–surfactants formed by the self-assembly of NPs and end-functionalized polymers at the hydrophilic/hydrophobic interface have a wide range of applications in many fields. In this study, the influence of density of amino groups, NPs dimension and pH on the interaction between end-functionalized polymers and NPs were extensively investigated. Single amino-terminated polystyrene (PS-NH2, Mw ≈ 0.6k, 2.5k, 3.5k, 3.9k) and diamino-terminated polystyrene (H2N-PS-NH2, Mw ≈ 1.1k, 2.8k) were prepared using reversible addition–fragmentation chain transfer polymerization and atom transfer radical polymerization. NPs with different dimensions (zero-dimensional carbon dots with sulfonate groups, one-dimensional cellulose nanocrystals with sulfate groups and two-dimensional graphene with sulfonate groups) in the aqueous phase were added into the toluene phase containing the aminated PS. The influence of pH and the molecular weight of amino-terminated PS on the interfacial tension between two phases were investigated. The results indicate that aminated PS exhibited the strongest interfacial activity after compounding with sulfonated NPs at a pH of 3. Terminating PS with amino groups on both ends leads to better performance in in reducing the water/toluene interfacial tension than modifying the molecular structure of PS on a single end. The dimension of sulfonated NPs also contributed significantly to the reduction of the water/toluene interfacial tension. The minimal interfacial tension was 4.49 mN/m after compounding PS-NH2 with sulfonated zero-dimensional carbon dots. Molecular dynamics simulation on the evolution of the water/toluene interface in the presence of sulfonated carbon dots and H2N-PS-NH2 revealed that these opposite charged substances moved towards the interface in an extreme short time and orderly assembled in a thermodynamic equilibrium.

Safety of source water streams is an urgent environmental issue, while protections in monsoon controlled subtropical regions face difficulties because of the lack of small scaled observation and analysis in small source water catchments. Basing on continuous weekly water quality data (2014-2017) in Pingqiao River Catchment, the annual average values of TN, NO₃, NH₄ and TP are 3.36, 1.64, 0.28 and 0.02 (mg/L) respectively. During dry, normal and wet seasons, the variability of parameters is over 35%, which indicates an obvious seasonality. Multiple methods are combined in order to assess the water quality and find the driving factors during dry, normal and wet seasons. This study suggests precipitation and fertilization are the mainly seasonal factors, which can make water quality better in wet season than dry season due to the dilution effect. The mechanism between seasonality and compound of nutrients can also be traced by log(TN:TP), and log(NO₃:NH₄). Among six main land use types (forest, tea plantation, cropland (paddy), urban, bare soil and water), the former three ones are influential mostly during dry and wet season. Tea plantation has the largest nutrients discharge amount per area, which is similar to cropland in dry season. By contrary, forest has the double power in reducing nitrogen release in wet and normal seasons. When transformed into paddies, croplands can lower the phosphorus concentration. Conclusions of this study can be used in southeastern China and similar regions on source water protection and agricultural plans.

Background: Hypoalbuminemia is known to be associated with adverse outcome in critical illness. In this study, we attempted to identify if hypoalbuminemia on emergency department (ED) arrival a reliable predictor for in-hospital mortality in necrotizing fasciitis (NF). patients. Method: A retrospective cohort study of hospitalized patients with NF was conducted in a tertiary teaching hospital in Taiwan between March 2010 and March 2018. Blood samples were collected in the ED upon arrival, and serum albumin levels were determined. we evaluated the predictive value of serum albumin level at ED presentation for in-hospital mortality. All collected data were statistically analyzed. Result: Of the 707 NF patients, 40 (5.66%) died in the hospital. The mean serum albumin level was 3.1 ± 0.9 g/dL and serum albumin levels were significantly lower in the non-survivor group than in the survivor group (2.8± 0.7 g/dL vs. 3.5 ± 0.8 g/dL). In the multivariable logistic regression model, albumin was associated with in-hospital mortality significantly (odds ratio[OR] 0.92, 95% confidential interval (CI) 0.88–0.96, P <0.001). The area under-the-receiver-operating-characteristic curve (AUC) for in-hospital survival was 0.77 (95% CI 0.72–0.82) and corresponding sensitivity, specificity, positive predictive value, negative predictive value, positive and negative likelihood ratio were 66%, 74%, 33%, 88%, 2.25 and 0.48, respectively. High sensitivity (96%) was shown at albumin level of 4.0 g/dL and high specificity (91%) was shown at level of 2.5 g/dL. Conclusion: Initial serum albumin levels were independently associated with in-hospital mortality among adult patients with necrotizing fasciitis and demonstrated fair discriminative performance in the prediction of in-hospital mortality. NF patients with hypoalbuminemia on ED arrival should be closely monitored for signs of deterioration and consider early and aggressive intervention to prevent mortality.

T-2 toxin produced by fungi of Fusarium genus is highly toxic to human and animals and has been shown to induce apoptosis in various organs/tissues. Apoptosis and autophagy are interconnected processes and these interactions are important for cellular homeostasis as well as pathogenesis. In this study, we report for the first time that T-2 toxin induced autophagy in human liver cells (L02). We showed that T-2 toxin induced the formation of acidic vesicular organelles, concordant with the time and dose-dependent alterations in LC3-phosphatidylethanolamine conjugate (LC3-II) LC3-I/II and p62/SQSTM1 suggesting an enhanced autophagic flux. The T-2 toxin-induced formation of autophagosome and lysosomal fusion was observed by expressing mRFP-GFP-LC3 in L02 cells by lentiviral transduction, and autophagosome was observed by transmission electron microcopy. We found that while T-2 toxin activated both apoptosis and autophagy, activation of autophagy appears to be a leading event reflecting the protective mechanism of cells against the insults by T-2 toxin. Activating autophagy by rapamycin (RAPA) inhibited the apoptosis while suppressing autophagy by chloroquine greatly enhanced the T-2 toxin-induced apoptosis suggesting the crosstalk of autophagy and apoptosis. In summary, our study showed that activation of autophagy protects liver cells from T-2 toxin-induced apoptosis suggesting autophagy may be targeted for prevention of the T-2 toxin-induced toxicity in human and animals.

Praeruptorin A(PA), a naturally existing pyranocumarin, is isolated from the dried root of Peucedanum praeruptorum Dunn. So far the anti-cancer effect and molecular mechanism behind Praeruptorin A action in human cervical cancer HeLa cells remain unknown. In the present study, we find that PA reduces cell proliferation and colony formation of human cervical cancer HeLa cells through inducing cell cycle arrest at G0/G1 phase. PA-upregulated p21 and p27 proteins are observed, accompanied with inhibition of cyclin D1 and S-phase kinase-associated protein 2(Skp2) proteins expression. PA could significantly inhibit migration and invasion of human HeLa cells. Meanwhile, PA significantly reduces invasive protein expression of matrix metalloproteinase-2 (MMP-2), and increases protein expression of tissue inhibitor of metalloproteinase-2 (TIMP-2). PA is observed to possess the capacity in suppressing ERK1/2 activation. PD98059 (ERK specific inhibitor) significantly enhances PA-induced downregulation of MMP-2 expression, and upregulation of TIMP-2 expression. Moreover, we found that PA treatment notably inhibits 12-O-tetradecanoylphorbol-13-acetate(TPA)-upregulated ERK1/2 activation, MMP-2 expression, cellular migration and invasion in human HeLa cells. Taken together, these findings are the first to demonstrate the anti-cancer activity of PA, which may act as a promising therapeutic agent for the treatment of human cervical cancer.

Alzheimer’s disease (AD) is an age-related neurodegenerative disease and is clinically characterized by cognitive impairment, memory loss, and personality disorder. Oligomers of amyloid beta-peptides (Aβ) and enhanced oxidative stress in senile plaques are prevalent pathologic hallmarks of AD. In this study, we detected the behavioral performance of Lycium ruthenicum Murray anthocyanin (LRA) -treated rats using the Morris water maze test and then investigated the effect of LRA on oxidative damage, neuronal apoptosis, and inflammatory response induced by Aβ1–42. Our results showed that LRA treatment markedly ameliorated the behavioral performance of Aβ1–42-induced rats and reduced the level of malondialdehyde, formation of protein carbonyl, and 8-hydroxy-2’-deoxygua-nosine. Furthermore, LRA also inhibited activated astrocytes and neuroinflammation via suppression of glial fibrillary acidic protein and tumor necrosis factor-alpha in the hippocampus of Aβ1–42-treated rat brain. These data suggest that LRA could be a potential anti-oxidant and anti-neuroinflammatory agent for the treatment of AD.

The impact of antecedent soil moisture content on soil erosion is a complicated phenomenon, which is still under argument with contradictions in research results. Hence, the objective of this study is to investigate the impact of antecedent soil moisture content to soil loss on clay soil by conducting two-year field experiments under natural rainfall on runoff plots with length of 10 meters, width of 3 meters, and uniform slope of 9%. Volumetric soil moisture sensors were used to log soil moisture changes, and soil moisture readings were used along with rainfall records to quantify the antecedent soil moisture conditions for each rainfall event. Results of this study show duration of the effective erosion event outranks the antecedent volumetric soil moisture content. Field study also suggests that accumulative rain falling within 48 hours (Pp48) prior to an effective erosion event strongly correlated with soil loss per Rainfall-Runoff Erosivity Index (Soil Loss / EI30), particularly when the duration of an effective erosion event is either between 3 ~ 7 hours or 10~ 30 hours. Hence, Pp48 can be considered as an alternative to replace antecedent soil moisture content in RUSLE 2’s cover and management factor.

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

The increasing growth in road users who are unfamiliar with traffic rules and regulations provides a serious safety problem for Pakistani traffic conditions. This study has two main objectives. First, it seeks to validate the reliability and applicability of the Dula Dangerous Driving Index (DDDI) in Pakistan. Second, it intends to investigate the effects of DDDI, sociodemographic characteristics, seat belt use, and driving training on the occurrence of traffic accidents. A total of 623 Pakistani individuals completed a questionnaire as part of this study. The questionnaire consists of items related to dangerous driving behaviors, sociodemographic characteristics, seat belt use, driving instruction, and accident involvement. The DDDI's accuracy was evaluated by comparing it to self-reported traffic incidents and seat belt compliance. To discover predictors within the DDDI dimensions, generalized linear models were used. A binary logistic regression analysis was also performed to evaluate the factors that influence traffic accidents. DDDI dimensions, demographic characteristics, seat belt usage, and driving training were all considered in this study. The use of seat belts while driving reduced the likelihood of an accident by 25%. On the other hand, aggressive driving and risky driving increased the chances of getting involved in traffic accidents by 36%% and 20%. Furthermore, the chances of being involved in a traffic accident decreased by 21% as the drivers age increased. The results also illustrate that Pakistani drivers are more aggressive and risk taker compared to Chinese drivers who are more disciplined. This study suggests that lack of comprehensive and standardized driving training and education programs, in consistent enforcement of traffic laws, the quality of road infrastructure and lack of public awareness campaigns can be attributed to adverse road safety situations in country.

The performance analysis of the internal/external flows around a high speed vehicle in near-space is fundamental and critical to the configuration and structure design for high speed aircraft. In this paper, the two-dimensional coupled implicit Reynolds Average Navier-Stokes (RANS) solver and RNG k–ε turbulence model is employed to numerically simulate the flow field of an integrated high speed vehicle. The flow field are divided three parts to solve separately and compared with that solved by integrated simulation. The flow field are decomposed to save computer storage and simulation time. The first part is inlet/isolator, the second part is combustion chamber and the third is nozzle. In the computation process, the outlet condition of isolator is endowed to the inlet boundary of combustion chamber and the outlet boundary of combustion chamber is endowed to the inlet boundary of nozzle, then the whole flow field of integrated high speed vehicle is solved. Aerodynamic characteristic of fragment-computation and integration-computation is comparatively analyzed at different angles of attack, the results show that the maximum deviation of lift coefficient obtained by fragment-computation is less than 3% compared with that by integration, the maximum deviation of drag coefficient fragment-computation is less than 5% compared with that by integration, while pitching moment coefficient deviation less than 12%. However, for simulation time-consumption, the time used by fragment-computation reduces 45% compared with integration-computation. Meanwhile, by components force analysis, it can be concluded that the aerodynamic property of inlet/isolator can been obtained separately and hardly effected by other parts.

In order to achieve its carbon peak and neutrality targets, a high proportion of distributed power sources are connected to the distribution network in China, which greatly increases the risk of distribution network operation. Aiming at the above problems, this paper proposes an active distribution network risk planning model based on multi-source data from carbon capture and power internet of things, and conducts exceeding testing of distribution network based on the stochastic load flow algorithm with semi-invariant and level expansion, calculates the semi-invariant of each order of node state vectors and branch current vectors, and then utilizes the Gram-Charlier level expansion to obtain the exceeding probability density function and probability distribution function of the node voltages and line powers of the distribution network. The probability density function and probability distribution function of the exceeding are obtained using the Gram-Charlier series expansion. Combined with multi-source data, the active distribution network with integrated energy system considering carbon capture is modeled. According to the risk scenario of the distribution network, the nonconvex constraints in the model are simplified by the second-order cone relaxation, and the optimal planning scheme of the distribution network is solved by combining the gurobi solver with the risk index as the first-level objective and the economic benefit as the second-level objective. The simulation results of a coupled network consisting of a 39-node distribution network and an 11-node transportation network verify the effectiveness of the proposed model.

Time-modulated sparse circular array (TMSCA) with elements uniformly excited is designed and synthesized in this paper. By utilizing rotationally symmetric structure, the array geometry and the time modulation of the TMSCA is presented, and the radiation patterns in frequency domain are formulated. In order to achieve the desired radiation pattern at the operating frequency and suppress the sideband radiation, the synthesis problem is established and solved by the proposed harmony search-convex programming (HS-CP) algorithm in two dependent optimizations. Two designs are presented, and the numerical results indicate that the TMSCA with rotationally symmetric structure has the advantages of designing time-modulated sparse arrays with superior performance.

CdZnTe (CZT) is a new type of compound semiconductor that has emerged in recent years. Compared to other semiconductor materials, it possesses an ideal bandgap, high density, and high electron mobility, rendering it an excellent room-temperature composite semiconductor material for X-ray and γ-ray detectors. Due to the exceptional performance of CZT material, detectors manufactured using it exhibit high energy resolution, spatial resolution, and detection efficiency. They also have the advantage of operating at room temperature. CZT array detectors, furthermore, demonstrate outstanding spatial detection and three-dimensional imaging capabilities. Researchers worldwide have conducted extensive studies on this subject. This paper, building upon this foundation, provides a comprehensive analysis of CZT crystals and CZT array detectors, summarizes existing research to offer valuable insights for envisioning new detector methodologies.

To reveal the antibacterial effect of wound secretions of different Chinese fir strains on five kinds of bacteria. Three 3-year-old seedlings of Taxus chinensis var.koraiensis and Yangkou and the 3-year-old container seedlings of Taxus chinensis var.pendula, Yang061 and Yang020, were used as the research objects. The antibacterial effect of wound secretions was determined by the filter paper diffusion method, and the antibacterial effect was analyzed. Results showed that the wound secretions of different strains of Chinese fir bark had noticeable bacteriostatic effects on Bacillus subtilis, Salmonella paratyphi B, Pseudomonas aeruginosa, Escherichia coli, and Staphylococcus aureus. However, the bacteriostatic effects of different strains of Chinese fir secretions differed. The minimum inhibitory concentrations (MICs) of the wound secretions of different strains of Chinese fir against the five test bacteria differed. The mean MIC of Pseudomonas aeruginosa was the highest, and the mean MIC of Escherichia coli was the lowest. The antibacterial ability of the wound secretions of different Chinese fir strains was mainly determined by the composition of the wound secretions. There was no noticeable relationship with the number of wound secretions.

With the global warming and the frequent occurrences of harsh environments, mooring line failures are frequent. Response analysis of the platform structure and its residual mooring system under multiple mooring line failures is needed. Therefore, it is necessary to investigate the change law of platform motion response after mooring line failure to find out the reasons for the change. Studies for different failure combinations of mooring lines show that the variation of the steady-state equilibrium position of the platform is closely related to the stiffness, with a clear functional. The duration and amplitude of the transient response are mainly influenced by the Morison drag force. And it was found that the suspended mooring line reduced the motion responses. It is also found that the mooring line failure increased the effective tension and suspension length of the riser. Based on the improved Dezert-Smarandache theory (DSmT), it is calculated that mooring line failure has little effect on the failure probability in different zones of the riser.

Legume-rhizobial symbiosis leads to to the formation of root nodules, where rhizobia reside and develop into bacteroids to reduce nitrogen into ammonium for plant growth, which leaves an opening question as how plant immunity is attenuated in nodules in the presence of large number of foreign bacteria. In Medicago truncatula, mutation in NAD1 (Nodules with Activated Defense 1) only produces necrotic nodules with overactivated immunity, indicating NAD1 is an indispensable component required for suppressing immunity in nodules. In this study, a dual RNA-seq transcriptomic technology was performed to extensively analyze gene expressions in nad1-1 mutant nodules. We indenifited 89 DEGs in symbiotic nitrogen fixation and 89 DEGs in immunity in Medicago truncatula at 10 dpi. Simultaneously, we indenifited 27 DEGs in fix and nif genes in Sinorhizobium meliloti. Then we identified 56 DEGs related to stress, including ROS, NO, and NCR, most of which were upregulated in Sinorhizobium meliloti. Our analyses of nitrogen fixation-defective plant nad1-1 mutants with overactivated defense indicate that host use plant immunity to control massive bacterial colonization during early and late symbiotic stages. Our findings provide insight into the function of NAD1 in improvement or inhibition of plant immune response to maintain symbiosis during rhizobial endosymbiosis.

Inosine 5'-monophoaphate (IMP) allows animals to sense umami. Intake of IMP in C57/KsJ-db/db (db/db) mice induced lipohyperplasia causing the liver cirrhosis, however, how to that of in normal mammals injure health is still unclear. Thus, we had investigated that intake of IMP in C57BL/6J mice effected its metabolic functions. We found that intake of 255 M/d IMP in C57BL/6J mice for 4 months induced hyperlipidemia and body fat rate raised. In mechanism, the expressions of ACC1 and phosphorylated ACC2 in hepatocytes were increased though IMP promoting phosphorylation of AMPK. The increased ACC1 promoted the conversion of acetyl-CoA into TG. These TG were transported out of hepatocytes to avoid NAFLD, causing a deficiency of acetyl-CoA in liver, and then the increased phosphorylated ACC2 promoted cytoplasm fatty acids into mitochondria to convert into acetyl-CoA though the fatty acids β-oxidation pathway, causing a deficiency of fatty acids. Therefore, liver enhanced the absorption of exogenous fatty acids, which were converted into TG caused lipohyperplasia. Moreover, intake of IMP in normal mice induced complement system weaken in liver causing mild inflammation. Our data not only alerted that humans avoid excessive intake of IMP, but also provided novel insights into the adipose of metabolic dysfunctions.

The decreasing width, increasing aspect ratio RDL presents significant challenges to design for reliability (DFR) of advanced package. Therefore, this paper proposes a ML based RDL modeling and simulation method. In the method, RDL is divided into blocks and subdivided into pixels of metal percentage, and the RDL is digitalized as tensors. Then, an ANN-based surrogate model is built and trained by a subset of tensors to predict the equivalent material properties of each block. Lastly, all blocks are transformed into elements for simulations. For validation, line bending simulations were conducted on an RDL, with the reaction force as accuracy indicator. The results show that neglecting layout impact causes critical errors as substrate thins. By the method, the reaction force error is 2.81% and the layout impact can accurately be considered with 200×200 elements. For application, the TCT maximum temperature state simulation was conducted on a CPU chip. The simulation indicates that for advanced package the maximum stress more likely occurs in RDL rather than bumps, both RDL and bumps are critical impacted by layouts, and RDL stress is also impacted by vias/bumps. The proposed method precisely concerns layout impacts with little resources, presents an opportunity of efficiency improvement.

After cut by basecutter, sugarcane stalks are carried to a chopper by the basecutter and the feeding/conveying rollers train of harvester. However, the conventional feeding/conveying channels of sugarcane chopper harvesters, when harvesting seriously lodged sugarcane, have numerous drawbacks, including easy clogging, and poor adaptability. In order to resolve these problems, a novel design and layout method of feeding/conveying and chopping channel are proposed in the paper. And a chopper centrally-mounted channel is designed for a sugarcane chopper harvester as well, which has been implemented in the HN4GDL-91 harvester. The proposed channel consists of a feeding/conveying rollers train, a chopper, and a billet conveying device. By mounting the chopper between the feeding/conveying rollers train and the billets conveying device, the harvester can avoid the chopper chopping back the billets, thus improving the harvest quality. The feeding/conveying rollers train is designed with only a pair of feeding rollers and a pair of conveying rollers, achieving a short channel path. Moreover, the structure of the basecutter and the mechanism carrying stalks to feeding rollers are studied via theoretical analysis and tests. The relationship between the basecutter and the chopper centrally-mounted channel is also conducted in systematic analysis. The results of the theoretical analysis show that the inclination angle of the disc of basecutter should be 2° greater than the angle of the feeding conveying channel (both angles are from the horizontal plane). The inclination angle of the disc of basecutter should go from 10° to 15°. A field experiment with four factors and three levels indicates that the field loss rate is 2.45%, the feed quantity is 16.66 kg/s, and the qualified rate of the billets is 98.02%, while the number of sugarcane stalks in a clump, the ground speed of harvester the rotational speed of the chopper, and the rotational speed of feeding/conveying roller are 10, 1.09 m/s, 390 r/min, and 230 r/min, respectively. It is concluded that the proposed chopper centrally-mounted channel could improve the conveying and harvesting performance significantly.

Cooking is a very decentralized and private way of energy consumption in human activities. The existing investigation and statistical analysis can’t effectively calculate the proportion of population relying on clean cooking fuel and utilization technology in the region. Therefore, based on the big data of the earth, this paper adopts the combination of spatial analysis and statistical analysis to determine the survey sample area, and according to the economic conditions, topographic characteristics, national policies for new energy construction and living habits of the provinces and cities under investigation, the questionnaire survey is conducted for the research area to calculate the proportion of the regional population relying on clean cooking fuels and utilization technologies. Taking the south of the Yangtze River in China as an example, the paper effectively calculates that 88.25% of the population depends on clean cooking fuel and technology in this region, of which 89.81% are in urban areas and 79.87% are in rural areas. Analysis of the survey data shows that the proportion of the population using clean cooking fuels and technologies is related to factors such as economic development, income and resource endowment. There is a large urban–rural gap in terms of energy consumption tendency and structure in the south of the Yangtze River in China and cooking energy consumption in rural households also varies from region to region. The technical ideas and conclusions of the paper have high reference application value, which can help promote the upgrading of clean energy utilization and provide data basis for relevant decision and policy making.

MultiCal is an affordable, high-precision measuring device designed for the on-site calibration of industrial robots. Its design features a long measuring rod with a spherical tip that is attached to the robot. By restricting the rod’s tip to multiple fixed points under different rod orientations, the relative positions of these points are accurately measured beforehand. A common issue with MultiCal is the gravity deformation of the long measuring rod, which introduces measurement errors into the system. This problem becomes especially serious when calibrating large robots, as the length of the measuring rod needs to be increased to enable the robot to move in a sufficient space. To address this issue, we propose two improvements in this paper. Firstly, we suggest the use of a new design of the measuring rod that is lightweight yet has high rigidity. Secondly, we propose a deformation compensation algorithm. Experimental results have shown that the new measuring rod improves calibration accuracy by 20% to 39%, while by using the deformation compensation algorithm, the accuracy increases by 6% to 16%. In the best configuration, the calibration accuracy is similar to that of a measuring arm with a laser scanner, producing an average positioning error of 0.274 mm and a maximum positioning error of 0.838 mm. The improved design is cost-affordable, robust, and has sufficient accuracy, making MultiCal a more reliable tool for industrial robot calibration.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

In recent years, the unmanned aerial vehicle (UAV) synthetic aperture radar (SAR) has become a highly sought-after topic for its wide applications in the field of target recognition, detection, and tracking. However, SAR automatic target recognition (ATR) models based on deep neural networks (DNN) are suffering from adversarial examples. Generally, non-cooperators rarely disclose any information about SAR-ATR models, making adversarial attacks challenging. In this situation, we propose Transferable Adversarial Network (TAN) to attack these models with highly transferable adversarial examples. The proposed method improves the transferability via a two-player game, in which we simultaneously train two encoder-decoder models: a generator that crafts malicious samples through a one-step forward mapping from original data, and an attenuator that weakens the effectiveness of malicious samples by capturing the most harmful deformations. In particular, compared to traditional iterative methods, our approach is able to one-step map original samples to adversarial examples, thus enabling real-time attacks. Experimental results indicate that the proposed approach achieves state-of-the-art transferability with acceptable adversarial perturbations and minimum time costs compared to existing attack methods, i.e., it excellently realizes real-time transferable adversarial attacks.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

In response to the increasing energy demand in Taiwan and the global trend of renewable energy development, Kuroshio energy is a potential energy source. How to extract this invaluable natural resource has then become an intriguing and important question in engineering practices. This study conducted a study for a nozzle-diffuser duct (NDD) as the Kuroshio currents energy harvester. The computational fluid dynamics (CFD) software ANSYS Fluent was employed to calculate the drag and added mass coefficients of the duct anchored to the seabed. Those coefficients were further imported into Orcaflex to simulate the motion of the duct under normal and storm wave conditions. Results showed that the duct was stable 25 m below the sea surface under normal wave condition. When the wave condition changed to storm waves, the duct needed to dive into at least 90 m below the sea surface to regain its stability and obtain high power take-off (PTO). An optimal design nozzle-diffuser-duct was reported and a PTO peak of 15 kW was expectable in the Kuroshio currents. Once a suitable offshore platform can be developed with sixty-six NDDs, a Megawatt Kuroshio ocean current power generation system is feasible in the near future.

The effect of Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results demonstrate that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites in the weld metal, and significantly improve the toughness. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. Excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties.

Coral reefs are declining worldwide due to global changes in the marine environment. The increasing frequency of massive bleaching events in the tropics is highlighting the need to better understand the stages of coral physiological responses to extreme conditions. Moreover, like many other coastal regions, coral reef ecosystems are facing additional localized anthropogenic issues such as nutrient loading, increased turbidity, and coastal development. Different strategies have been developed to measure the health status of a damaged reef, ranging from the resolution of individual polyps to an entire coral community, but techniques for measuring coral physiology in situ are not yet widely implemented. For instance, while there are many studies of the coral holobiont response in single or limited-number multiple stressor experiments, they provide only partial insights to metabolic performance under more complex temporally and spatially variable natural conditions. Here, we discuss the current status of coral reefs and their global and local stressors in the context of experimental techniques that measure core processes in coral metabolism (respiration, photosynthesis, and biocalcification) in situ, and their role in indicating the health status of colonies and communities. We highlight the need to improve the capability of in situ studies in order to better understand the resilience and stress response of corals under multiple global and local scale stressors.

Traditional potential transformers have problems of large volume, difficulty in insulation, iron core saturation, ferroresonance overvoltage and poor transient response characteristics. The voltage sensor based on the principle of electric field coupling and differential input structure does not need to contact the measured object or ground, and can avoid the above problems. However, it requires a sufficiently high capacitance between the differential electrodes to obtain sufficient accuracy and a high voltage division ratio. The existing method of using mutual capacitance between the differential electrodes will cause many problems and fail to meet the practical needs. To solve the above problems, this paper innovatively uses multi-layer ceramic capacitor to replace the mutual capacitance and designs a new type of voltage sensor. In addition, by using single bypass small resistance grounding method to increase the input impedance of the differential signal processing circuit, error of the sensor is further reduced. The experimental results show that the sensor has excellent accuracy and great transient response characteristics. The ratio error under power frequency is within ±0.5% and the phase error is within 1. The ratio error in the range of 500 Hz∼30 kHz is within ±5% and the phase error is within 5. Moreover, it has the advantages of low cost, miniaturization, flexible shape and easy to adjust the voltage division ratio. These characteristics indicate that the sensor has good voltage measurement and sensor network potential.

Existing methods for detecting magnetic leakage signals from damaged wire ropes require axial saturation magnetisation, and the accuracy of the detection equipment depends on the saturation degree of magnetisation. Moreover, the expected magnetisation effect is usually difficult to achieve owing to the special characteristics of the rope structure, diameter, and operating environment of the wire rope. Consequently, in addition to other issues, the detection accuracy and versatility of the equipment are low. In this study, a method based on spatial multidimensional orthogonal array loop magnetisation for detecting mine wire rope defects is proposed. Firstly, a new sensor excitation structure model is developed. Then a method of radiant magnetic flux of permanent magnet array is analysed, and the influence law of the number of permanent radiant magnetic blocks on the magnetisation effect is studied. In addition, a method of wire rope detection based on the principle of clustering is investigated, according to which the influence law of the shape, structure, and size of the polyurethane device on the effect of magnetisation is discussed. Finally, through laboratory experiments, the test model and proposed method are verified. The results show that the magnetisation effect is better and more cost-effective when the number of permanent magnet radiation magnetic block is n=8, and the proposed detection method can effectively distinguish damaged wire rope joints. Furthermore, the proposed equipment achieved signal-to-noise ratio of the signals, improving the reliability of damage detection.

(E)-β-ocimene was the only found volatile chemical emitted by whole, live worker larvae of Apis mellifera L. by sampling in the vapor phase. While in addition to (E)-β-ocimene, there is evidence for the existence of other volatiles; but the changes of their composition and contents remain unknown during larval development, as are their differences from larvae to larval food. This is the main purpose of the study. We investigated volatile components of worker larvae and larval food using solid phase dynamic extraction (SPDE) coupled with gas chromatography-mass spectrometry (GC-MS). Nine compounds were identified with certainty and six tentatively, consisting of terpenoids, aldehydes, hydrocarbons, ester and ketone. The contents of volatiles of the second-instar worker larvae differ greatly from larvae of other stages mainly attributable to terpenoids, which made the second-instar worker larvae had significantly higher amounts of overall volatiles. Larval food contained significantly higher amounts of aldehydes and hydrocarbons than the corresponding larvae from the fourth to fifth-instar. We discovered volatiles in worker larvae and their food which were never reported before; we also mastered the change of these volatiles’ contents during larval development.

Carboxylic acids such as acetic acid and propionic acid have been investigated as representative components for fast pyrolysis (FP) bio-oil upgrading. Selective catalytic conversion of carboxylic acids can enhance bio-refinery processing economics through catalyst preservation and process intensification. Various metal-doped molybdenum carbide bead catalysts have been synthesized and developed in this work. Our aim is to enable selective conversion of carboxylic acids. In the case of acetic acid conversion, calcium doped Mo₂C beads offer the highest yield of acetone ~96% at 450 °C among undoped and Ca or Ni doped catalysts. By comparing hot gas filter with and without Ca-Mo₂C catalyst tested with real FP vapors, the former showed a 36.7% reduction of acetic acid, a 37.5% reduction of small ketones in aqueous phase, and a ~50% reduction of methoxies (methoxy phenols and methoxy aromatics) in organic phase. The conversion resulted in the formation of more long chain chemicals in the organic phase, which are more amendable for downstream upgrading.

Microencapsulation of polyherbal formulation (PHF) extract was carried out by freeze drying method, by employing gum arabic (GA), gelatin (GE), and maltodextrin (MD) with their designated different combinations as encapsulating wall materials. Antioxidant components (i.e total phenolic contents (TPC),Total flavonoids contents (TFC), and total condensed contents (TCT)), antioxidant activity (i.e. DPPH, β-carotene & ABTS⁺ assays), moisture contents, water activity (aw), solubility, hygroscopicity, glass transition temperature (T_g), particle size, morphology, in vitro alpha-amylase and alpha-glucosidase inhibition and bioavailability ratios of the powders were investigated. Amongst all encapsulated products, T_B (5% GA and 5% MD) and T_C (10% GA) has proven to be the best treatments with respect to the highest preservation of antioxidant components and their antioxidant potential by DPPH and β-carotene assays and noteworthy for an ABTS⁺ assays, in addition, the aforesaid treatments also demonstrated lower moisture content, aw, particle size and higher solubility, hygroscopicity and glass transition temperature (T_g). All freeze dried samples showed irregular (asymmetrical) microcrystalline structures. Furthermore, T_B and T_C also illustrated the highest in vitro anti-diabetic potential due to great potency for inhibiting alpha-amylase and alpha-glucosidase activities. In the perspective of bioavailability, T_A, T_B and T_C demonstrated the excellent bioavailability ratios (%).Futhermore, the phytochemo-profiling of ethanolic extract of PHF was also revealed to find out the bioactive compounds.

Thymidylate synthase (TYMS) is an essential enzyme for the de novo synthesis of dTMP and has been a primary target for cancer chemotherapy. Although the physical structure of TYMS and the molecular mechanisms of TYMS catalyzing the conversion of dUMP to dTMP have been conducted thorough studies, oligomeric structure remains unclear. Here, we show that human TYMS not only exists in dimer but also octamer by intermolecular Cys43-disulfide formation. We optimize the expression condition of recombinant human TYMS using Escherichia coli system. Using HPLC-MS/MS, we show that purified TYMS has catalytic activity for producing dTMP. In the absence of reductant β-mercaptoethanol, SDS-PAGE and size exclusion chromatography (SEC) showed size of TYMS protein is about 35 KDa, 70 KDa, and 280 KDa. While the Cys43 was mutated to Gly, the band of ~280 KDa and the peak of octamer disappeared. Therefore, TYMS was determined to form octamer, dependent on the presence of Cys43-disulfide. By measuring Steady-State Parameters for monomer, dimer and octamer, we found the k_cat of octamer is increased slightly than monomer. On the basis of these findings, we suggest that octamer in the active state might have a potential influence on the design of new drug targets.

For the different harvest targets, the requirement for the prolificacy trait of maize was also different, so prolificacy is of great significance for modern production. Although some QTLs and genes associated with prolificacy in teosinte have been reported, the genetic mechanism of prolificacy in maize has not been fully elucidated. In this study, two RIL populations and GWAS population were used to genetic research of prolificacy trait in maize, with multi-environment. Combine linkage analysis and Genome-wide association study has identified a total of 13 QTLs and 8 significant SNPs. There were two genes related to tissue differentiation in the stable QTL qP9-2, and two significant SNPs corresponding to three genes were in QTL qP5-1 and QTL qP7-1, respectively. Four candidate genes GRMZM2G317262, GRMZM2G317584, GRMZM5G882364 and GRMZM2G141679 were finally screened out by qRT-PCR analysis. Based on the function of candidate genes, ethylene signaling pathway plays an important role in the formation of prolificacy in maize. It has deepened our understanding of the formation mechanism of prolificacy and laid a foundation for breeding new varieties with various prolificacy in maize.

Arsenic is a prevalent environmental pollutant with recognized carcinogenic properties. Liver fibrosis is a frequent consequence of arsenic poisoning, with the activation of hepatic stellate cells (HSCs) being a central event. Solute Carrier Family 7 Member 11 (SLC7A11), a pivotal regulator of ferroptosis, may be involved in the process of arsenic-induced liver fibrosis. This study utilized lentiviral vector-mediated SLC7A11 silencing in LX-2 cells (a type of human hepatic stellate cells) to establish an SLC7A11 knockout cell model, which was then exposed to sodium arsenite (NaAsO2). Protein interactions were assessed through Protein Immunoprecipitation (IP), and protein levels were evaluated via Western blot analysis. It was found that NaAsO2 decreased cellular Fe2+ levels and nuclear receptor co-activator 4 (NCOA4) expression, with SLC7A11 silencing reversing these effects. Additionally, IP analysis revealed an interaction between Beclin1 and SLC7A11 proteins in LX-2 cells exposed to NaAsO2. Silencing SLC7A11 attenuated the reduction in Tumor Protein p53(P53), and p-mammalian target of rapamycin (p-mTOR) protein levels, along with the rise in Beclin1, Phosphorylated adenosine monophosphate activated protein kinase (p-AMPK), α-smooth muscle actin (α-SMA) and Fibroblast activation protein-α (FAP) induced by NaAsO2. Consequently, SLC7A11 silencing promoted cellular ferroptosis, reduced autophagy levels through the P53/AMPK/mTOR pathway, and inhibited HSC activation by NaAsO2, potentially mitigating liver fibrosis.

Assessing observation noise is a critical step in the development of a stochastic model for GNSS navigation and positioning. This process ensures that the statistical properties of the observational data are accurately characterized, leading to more reliable and precise positioning results. Traditionally, the one sigma values for observation noise, 0.3 m for code and 3 mm for carrier phase, alongside elevation-dependent weighting schemes, have been standard. However, these may no longer be suitable due to significant advancements in GNSS systems, receivers, and antennas. Previous research predominantly focused on code type and PPP techniques, often limited by the inability to separately assess observation types across different frequency bands due to ionospheric delay. Furthermore, these studies were generally constrained by limited experimental data. This research advocates for the use of ultra-short baselines to eliminate atmospheric delay and other error sources, providing a detailed assessment of observation noise for various frequency bands, GNSS systems, and receiver & antenna types over an extensive period and across multiple baselines. The findings suggest a need to reconsider traditional one sigma values and elevation-dependent weighting schemes for current applications.

With the rapid development of tumor immunotherapy, nanoparticle vaccines have attracted much attention as a potential therapeutic strategy. The potential role of the mannose-modified lipid calcium phosphate nanoparticle vaccine in enhancing the anti-tumor immune response was investigated. The aim of this study was to investigate the effect of mannose modification on the immune response of nanoparticles in regulating the tumor microenvironment through systematic review and analysis and to explore its potential clinical application in tumor therapy. Currently, despite the potential advantages of nanoparticle vaccines in immunotherapy, achieving an effective immune response in the tumor microenvironment remains a challenge. Tumor immune escape and overexpression of immunosuppressive factors limit its clinical application. Therefore, this study will explore how to intervene in the immunosuppressive mechanism in the tumor microenvironment through mannose-modified lipid calcium phosphate nanoparticle vaccines so as to improve the immunotherapy effect of tumor patients and provide new ideas and strategies for the field of tumor therapy.

Under the double pressure of climate change and human activities, the restrictions of conservation policies and the increasing area of overlap between wildlife conservation areas and community living areas have led to increase conflicts and contradictions between nature reserves and neighboring communities. Effective management of such conflicts is particularly important in order to achieve reconciliation of conservation and development. In this study, we take the Mikumi-Selous region in Tanzania, Africa as an example, and through questionnaire surveys and semi-structured interviews, we sort out the current situation of conflicts between nature reserves and communities in the region, as well as summarize the means of conflict governance. In addition, we focus on identifying the various factors affecting community residents' protection willingness and protection action, and further verify the relationships among residents' family characteristics, protection costs and revenue, protection cognition, willingness and action through empirical analysis methods. The results show that residents' protection cognition has a significant positive effect on their willingness to protect and their actions, meanwhile willingness to protect also positively affects residents' protection action. In addition, it was found that the protection cost inhibits residents' willingness and action. Our study focuses on the willingness to participate and action of core stakeholders towards conflict governance from the perspective of community governance, emphasizing the key role of community participation in achieving coordinated development of biodiversity conservation and community. It provides a new perspective for mitigating conservation and development issues.

The gas-water relative permeability curve plays a crucial role in reservoir simulation and development for condensate gas reservoirs. In this study, we conducted a series of high temperature and high pressure analysis experiments on real gas cores from Wells A and B in Block L of the Yinggehai Basin to investigate the effects of temperature, pressure, and different types of gas media on gas-water seepage. The experimental results demonstrate that: Temperature has a significant impact on both gas and water relative permeability, particularly on the former. As temperature increases, gas relative permeability shows a substantial increase while water relative permeability remains relatively unchanged. Under the same effective stress, increasing pressure causes downward shifts in both the gas and water relative permeability curves; however, there is a more pronounced decrease in gas relative permeability. Gas type has minimal influence on phase permeability except at higher water saturation where differences become apparent. When water saturation ranges from 80% to 50%, there is no significant variation observed in the measured relative permeability of different displacement gases; however, as water saturation exceeds 80%, distinctions gradually emerge. At bound water saturation conditions, nitrogen exhibits lower relative permeability compared to simulated gases with approximately 92% similarity between them. This investigation into the characteristics of gas-water relative permeability in high temperature and high pressure condensate reservoirs within Yinggehai Basin provides valuable insights for efficient development strategies for similar reservoirs.

In order to the effect of hydrated phase change materials on suppressing coal spontaneous combustion, the thermogravimetric experiment and reaction activation energy analysis experiment were used to explore the changes of combustion characteristic, parameters characteristic temperature and activating energy of gas coal, long flame coal, meagre coal, and lean coal before and after adding hydrated phase change materials. The research results showed that hydrated phase change materials increased the coal samples’characteristic temperature point and have effective inhibitory effects on different stages of oxidation process.However, the effect was best at low temperatures, as hydrated phase change materials undergo phase change and absorb heat when heated at low temperatures, isolating coal from contact with oxygen. The activating energy increased by 1.138 KJmol-1～23.048 KJmol-1 and the mass loss reduced by 1.6%～9.3% after the inhibition of the coal sample,indicating that the oxidation rate of various coal samples can be slowed down and the spontaneous combustion can be suppressed by using hydrated phase change materials.At the same time, this material can also reduce the combustibility index of meagre coal and lean coal, as well as the comprehensive combustion index and maximum loss rate of long flame coal and gas coal.

Objective: To investigate the efficacy of a magnetic resonance imaging (MRI) radiomics model in predicting colorectal cancer liver metastasis (CRLM). Methods: A total of 120 patients who underwent baseline MRI examination at the Affiliated Hospital of North Sichuan Medical College from June 2016 to August 2022 and were pathologically confirmed to have colorectal cancer (CRC) were randomly divided into a training group and a validation group. The clinical risk factors and MRI data of all patients were collected. Univariate and multivariate analysis were used to screen the clinically independent risk factors for CRLM. The radiomic features of each sequence were extracted from oblique axial or axial fat-free T2-weighted imaging (T2WI) and diffusion-weighted imaging (DWI) sequences. Least absolute shrinkage and selection operator (LASSO) regression was used to screen the optimal radiomic features of each sequence. Logistic regression was used to establish a prediction model of each sequence (T2WI and DWI models), a combined radiomics model (M) integrating the features of T2WI and DWI sequences, and a combined imaging-clinical model (U) combining the radiomic features of each sequence with clinically independent risk factors. The area under the receiver operating characteristic curve (AUC) was calculated to evaluate the predictive performance of each model. Results: Among the 120 CRC patients enrolled, 57 had liver metastasis, and 63 did not. The tumor markers carcinoembryonic antigen and carbohydrate antigen 19-9 were clinically independent risk factors for CRLM. Three optimal radiomic features were screened from T2WI and DWI sequences through LASSO regression analysis, respectively. The AUC values of the T2WI, DWI, M, and U models were 0.811, 0.803, 0.824, and 0.899 in the training group and 0.795, 0.798, 0.813, and 0.889 in the validation group, respectively. The predictive performance of the combined models was better than that of the single-sequence models. The U model performed best at predicting CRLM. Conclusion: An MRI radiomics model based on CRC primary lesions can predict CRLM well. Our combined model integrating the radiomic features of each sequence and clinically independent risk factors had the best predictive performance.

To achieve a micro-destructive and rapid measurement of the wood density of standing trees, this study investigated the feasibility of using the micro-drilling resistance method, formulated a mathematical model, explored the potential for a unified model across multiple tree species, and analyzed the influence of moisture content on measurement accuracy. First, 231 tree cores and drill resistance data were sampled from Pinus massoniana, Cunninghamia lanceolate, and Cryptomeria fortunei. The basic density and moisture content of each core were measured, and the average value of each resistance data record was calculated. Second, the average drill resistance, the natural logarithm of average drill resistance, and absolute moisture content were used as independent variables, while the wood basic density was used as the dependent variable. Third, the total model of the three tree species and sub-model for each tree species were established through a stepwise regression method. Finally, the accuracy of each model was compared and analyzed with that of using the average basic density of each tree species as an estimated density. The results revealed that the estimation accuracy of the sub-model for each tree species was 1.670 percentage points higher than the average value of each tree species used as the density estimation value for these tree species. Additionally, except for Cryptomeria fortunei, the natural logarithm of drill resistance significantly influenced the wood density model at a significance level of 0.05. Moreover, moisture content significantly affected the total model and sub-models of Pinus massoniana at a significance level of 0.05. The estimation accuracy of the total mathematical model was 2.125 percentage points lower than that achieved using the average basic density of each tree species to predict their density. The results indicated the feasibility of using the micro-drilling resistance method to measure the wood density of standing trees. Moreover, the relationship between wood density and drill resistance did not follow a linear pattern, and moisture content slightly influenced the drill needle resistance. Furthermore, the establishment of a mathematical model for each tree species was deemed essential. This study provides valuable guidance for measuring the wood density of standing trees through the micro-drilling resistance method.

A La2FeCrO6 (LFCO) double perovskite powders were synthesized by hydrothermal method, which crystallized in an orthorhombic (Pnma) structure and exhibited a spherical morphology with average particle size of 900 nm. Fourier transformation infrared spectroscopy confirmed the octahedral coordination of Fe and Cr ions in the powders. XPS spectra revealed dual oxide states of Fe (Fe2+/Fe3+) and Cr (Cr3+/Cr4+) elements, and oxygen element appeared as lattice oxygen and defect oxygen, respectively. The LFCO powders exhibit ferromagnetic behavior at 5 K with saturation magnetization of 0.31 μB/f.u., coercive field of 8.0 kOe, and Curie temperature of 200 K. Griffiths phase appeared in the powders between 200 K and 223 K. The LFCO ceramics displayed a butterfly-like magnetoresistance (MR)-magnetic field (H) curve at 5 K with MR (5 K, 6 T) value of -4.07%. Temperature dependence of resistivity of the LFCO ceramics demonstrated their semiconducting nature. Electrical transport data were fitted by different conduction models. Strong frequency dispersion dielectric behavior was observed in the LFCO ceramics. A dielectric abnormality observed around 260 K, was ascribed to the jumping of electrons trapped in shallow levels created by oxygen vacancies. The dielectric relaxation behavior exhibited by dielectric loss between 160 K and 260 K, was contributed to the singly-ionized oxygen vacancies.

Metal fabrications experience complex physical metallurgical processes during additive manufacturing, leading to residual stress and coarse microstructure with directional growth. It significantly affects the comprehensive performance of the fabrications, which limits the application of additive manufacturing. Ultrasonic impact treatment (UIT), as a strengthening means to assist additive manufacturing, can effectively improve the stress state and refine the microstructure and the comprehensive performance. This paper introduces the effect of UIT on AM metal fabrications on microstructure morphology, stress distribution, surface roughness, internal defects, and comprehensive performance to gain a deeper understanding of the role of UIT on additively manufactured metal fabrications, which is based on the working principle and effect of process parameters. In addition, the strengthening mechanism of UIT in additive manufacturing is described from the perspective of surface plastic deformation and substructure formation, providing support for the shape and property control of metal fabrications in the process of additive manufacturing assisted by UIT. Finally, the issues that need to be studied in depth on UIT in additive manufacturing are summarized, and an outlook on future research directions is taken.

As the first pilot ecological civilization zone in China, Fujian Province has an excellent ecological environment quality, and its ecological environment-related indices continue to be among the highest in the country. In order to investigate the causes of the excellent ecological quality in Fujian Province in the past 15 years, this paper selects MODIS images, land use data and provincial and municipal statistical yearbook data of Fujian province from 2005 to 2020 as data sources, evaluates the ecological system health of Fujian Province by remote-sensing ecological index (i.e. RSEI), constructs the land use intensity system of Fujian Province at the same time, and uses a coupled coordination model to analyze the coupling between RSEI and The coupled coordination model was used to analyze the coupling relationship between RSEI and land use intensity, and finally the spatial and temporal evolution of ecological health in Fujian Province from 2005 to 2020 was analyzed. The results show that the coupled coordination between land use intensity and ecosystem health in Fujian province showed a continuous increase between 2005 and 2020, especially in Ningde, where the increase was most significant, from 0.0993 to 0.963, this pattern of spatial distribution is lower in the south-eastern coastal region than in the north-western interior, higher in the south-western region than in the north-western region, and higher in the north-eastern region than in the south-eastern region. In terms of the type of role, the land use intensity of most cities in Fujian Province in 2005 played an obvious role in blocking the degree of ecosystem health, but as time changed, urban land use continued to be optimized and reached moderate or even high quality coordination with the quality of the ecological environment, but Xiamen City developed relatively slowly and its 2020 coupling degree value was 0.315, which was still in mild disorder. This study fills a gap in the research mechanism of the interaction between the degree of ecosystem health and land use intensity, and also provides a new perspective for the construction of ecological civilization and the assessment of the degree of ecosystem health in Fujian Province and the whole country.

Desertification and dune progression over vegetation is quantified using remote sensing data, but vegetation, eventually temporarily, buried under sand blowout may escape such assessment, and to estimate the extent of buried vegetation, a GPR campaign was conducted over the coastal sand-dune of Tottori Prefecture (Japan) in combination with a high-resolution topographic UAV-based survey of the topography. The result shows that buried vegetation exists underneath sand-blowout, especially near the dune ridges, and that this vegetation can extend 20 – 30 m further than the estimation made from airborne remote sensing. Furthermore, the presence of palaeo-vegetation in palaeodune layers also provide information on the long-term evolution of sand dunes (with periods of stability vs rapid change), which can be used to reconstruct Quaternary coastal environments.

Klebsiella pneumonia (K. pneumoniae) is a Gram-negative bacterium that causes nosocomial infections in the lung, bloodstream, and urinary tract. Therefore, detecting K. pneumoniae in early time is important in preventing severe infections. However, clinical detection of K. pneumoniae requires a long time of agar plate culture. Nucleic acid detection like qPCR is precise but requires expensive equipment. Recent research reveals that collateral cleavage activity of CRISPR-LbCas12a has been applied in nucleic acid detection. In this study, PCR combined with CRISPR-LbCas12a targeting the K. pneumoniae system was established. This system showed excellent detection specificity and sensitivity in both bench work and clinical samples. Due to its advantages, its application can meet different detection requirements in health centers where qPCR is not accessible.

Background Radial extracorporeal shock wave therapy (rESWT) is an attractive, non-invasive therapy option to manage fracture nonunions of superficial bones, with a reported success rate of approximately 75%. Using zebra mussels (Dreissena polymorpha), we recently demonstrated that induction of biomineralization after exposure to focused extracorporeal shock waves (fESWs) is not restricted to the region of direct energy transfer into calcified tissue. This study tested the hypothesis that radial extracorporeal shock waves (rESWs) also induce biomineralization in regions not directly exposed to the shock wave energy in zebra mussels. Methods Zebra mussels were exposed on the left valve to 1000 rESWs at different air pressure (between 0 and 4 bar), followed by incubation in calcein solution for 24 hours. Biomineralization was evaluated by investigating the fluorescence signal intensity found on sections of the left and right valves prepared two weeks after exposure. Results General linear model analysis demonstrated statistically significant (p < 0.05) effects of the applied shock wave energy as well as of the side (left/exposed vs. right/unexposed) and the investigated region of the valve (at the position of exposure vs. positions at a distance to the exposure) on the mean fluorescence signal intensity values, as well as statistically significant combined energy × region and energy × side × region effects. The highest mean fluorescence signal intensity value was found next to the umbo, i.e., not at the position of direct exposure to rESWs. Conclusions As in the application of fESWs, induction of biomineralization by exposure to rESWs may not be restricted to the region of direct energy transfer into calcified tissue. Furthermore, the results of this study may contribute to better understand why the application of higher energy flux densities beyond a certain threshold does not necessarily lead to higher success rates when treating fracture nonunions with extracorporeal shock wave therapy.

Angelica decursiva is one of the lending traditional Chinese medicinal plants producing coumarins. Notably, several studies have focused on the biosynthesis and not the qRT-PCR (quantitative real-time reverse transcription polymerase chain reaction) study of coumarins. This qRT-PCR technique has been extensively used to investigate gene expression levels in plants and the selection of reference genes which plays a crucial role in standardizing the data form the qRT-PCR analysis. In our study, 11 candidate reference genes were selected from the existing transcriptome data of Angelica decursiva. Here, four different types of statistical algorithms (geNorm, NormFinder, BestKeeper, and Delta Ct) were used to calculate and evaluate the stability of gene expression under different external treatments. Subsequently, RefFinder analysis was used to determine the geometric average of each candidate gene ranking, and to perform comprehensive index ranking. The obtained results showed that among all the 11 candidate reference genes, SAND family protein (SAND), protein phosphatase 2A gene (PP2A), and polypyrimidine tract-binding protein (PTBP) were the most stable reference genes, where Nuclear cap binding protein 2 (NCBP2), TIP41-like protein (TIP41), and Beta-6-tubulin (TUBA) were the least stable genes. To the best of our knowledge, this work is the first to evaluate the stability of reference genes in the Angelica decursiva which has provided an important foundation on the use of qRT-PCR for an accurate and far-reaching gene expression analysis in this medicinal plant.

Considering the fault "N-1" checksum and the power flow, the single-phase power flow model is further transformed into a three-phase power flow model, and the asymmetry of the three-phase power flow is measured by the three-phase unbalance factor. The calculation model is linearized by the second-order cone relaxation and the Big-M method. At the same time, the load response and distribution network reconstruction are used to improve the reliability of the power supply network to cope with the power failure. The relationship between power supply capability and power flow constraints, main transformer capacity and distributed power parameters is analyzed by IEEE 33-node three-phase power distribution system. The feasibility of the proposed model and the accuracy of the second-order cone relaxation are verified by numerical examples, which provides a technical reference for distribution network planning.

Lung cancer remains the leading cancer killer worldwide. Early diagnosis can effectively increase the patient cure rate but existing diagnostic methods limit early lung cancer diagnosis. Therefore, development of a simple but efficient lung cancer screening method is important to improvement of both the diagnosis rate and the survival rate of lung cancer patients. In this study, ten photosensitive materials with high sensitivity and high specificity were screened accurately to construct a microarray sensor that can rapidly identify six types of lung cancer biomarkers in exhaled breath. Results from hierarchical cluster analysis (HCA), principal component analysis (PCA) and difference maps showed that the classification of the analytes agreed with structure similarity laws. The detection results from parallel experiments and structurally similar analytes, in turn, cluster into a group; the fingerprints of the different analytes have specific response regions. The well-screened sensor chip fabrication workload and cost were both reduced by approximately two thirds, while the microfluidic device sensitivity and stability increased by approximately 1.3 times their corresponding values before optimization. The dual-channel device also offers real-time contrast detection and synchronous parallel detection functions and has potential application prospects for use in extensive screening of high-risk populations for lung cancer.

Over 55% of stoma patients suffer complications such as dehydration. Outcomes may be improved through communicating stoma output data to the patient and their clinical teams. Past artificial neural networks to improve accuracy in fluid level sensing were designed to account for ‘slosh’ caused by variable acceleration in one or two axes of movement. This paper describes the development of a novel sensor platform for non-invasive monitoring of stoma output in real time through incorporating a volumetric array consisting of thermistors and capacitive sensors into an ostomy appliance. Stoma output which exits the body at core temperature passes into a stoma appliance in a pattern which is dictated by water content, existing effluent within the bag and distortion of the usual bag shape. By using thermistors, a thermal boundary demarcates the accumulated level of fecal material as the effluent settles. A capacitive array allows the measurement of volume of output. The sensing components communicates via near field communication (NFC) and transmits data to a smartphone application by Bluetooth low energy (BLE). Testing of the device on 11 existing ileostomy patients with 51.6 bag hours of data found a correlation between measured volume and predictive value, supporting its use in this population.

Synthesis of activated carbon from waste biomass is of current interest towards sustainability. The properties of biomass derived activated carbon largely depends on the carbonization process. This study reports preparing extremel high surface area mesoporous activated carbon from hemp bast fibre using hydrothermal processing. Processing in hot water (390-500^oC), then activation using KOH and NaOH was investigated at different loading ratios. The described approach was found to enhance the mesoporosity (centered at 3.0 to 4.5 nm) of the hemp derived activated carbon (HAC) from activation (confirmed by BJH pore size distribution and TEM imaging). BET results showed that the product has an extremely high surface area (2425 m²/g) while the surface functional groups (-OH, COOH, C=C/C-C) were confirmed and quantified by XPS and FTIR results. Increasing KOH concentration was found to enhance the surface area with an optimum biochar to KOH ratio of 1:3. The crystallite domain size of HAC was determined using Raman spectroscopy of different wavelengths. The procedure described in this study is an environmentally friendly scalable route for the mass production of activated carbon using hemp fiber.

Borneol and menthol were two terpenes wildly used as penetrate enhancer in transdermal drug delivery. To explore their penetration enhancement effect towards hydrophilic drug, 5-FU was selected as model drug. A method combined vitro permeation studies and coarse grain molecular dynamics was used to investigate their penetration enhancement effect towards 5-FU. As a result, although both borneol and menthol showed a penetration enhancement effect towards 5-FU, they differed a lot in the penetration enhancement mechanism, which was also thought to account for their different penetration enhancement effect. As for menthol, SC bilayer disrupting effect seemed to be its main mechanism. While for borneol, its mechanism seemed to be more complicated. Except for disrupting the SC bilayer, it could also increase the permeation of 5-FU by enhancing the diffusion rate of 5-FU or inducing the formation of transient pore. All of this enable us a molecular understanding of borneol and menthol’s penetration enhancement effect towards hydrophilic drug, which might provide some guidance in the latter research and application.

This project designed a set of network security mechanisms for cloud applications in VANETs. At present, cloud computing is one of the government’s development priorities in the industry. We divide cloud into public, private, and hybrid clouds in this project. Vehicles or passengers can access road conditions or public transport information through the public cloud; public transportation can access current driving records and users can access relevant enterprise information on the private cloud and hybrid cloud is a combination of public and private clouds. Both cloud computing or VANETs require network and information security. At present, many researches on VANETs security only focus on message communication, and neglect information storage. Researches on cloud computing security only focus on information protection, and neglect user privacy and anonymity. This project designed a set of network and information security mechanisms in line with the requirements of Confidentiality, Authentication, Non-repudiation, Conditional Anonymity, and Conditional Untraceability. This project primarily needs to achieve the following: 1.an authentication mechanism to verify the identity of each other between the passenger and the vehicle and to verify the identity with Single Sign-On; 2. vehicle or user privacy and anonymity, which need to be able to replace the anonymous ID and related parameters for the vehicle or the user; 3. a private communication mechanism, which enables any vehicle or user to communicate privately; and 4. an information security encryption method, which can encrypt the information on a cloud server to avoid unauthorized access by internal personnel or hackers.

A finite element model of 100m X-BOW polar exploration cruise is established. The entire ship frequency response analysis was carried out, comparing the simulated values with the test values, the maximum error is 22%, but only 0.24mm/s difference, the error can be ignored from the perspective of comfort, therefore, the simulation results meet the requirements of engineering accuracy and verify the effectiveness of the model. According to the solution method for global modal equivalent mass, combing the spatial distribution principle of local modal mass, the method for solving the equivalent mass of a single local mode in mixed mode is proposed, the equivalent mass of the local vibration region of 100m X-BOW polar exploration cruise ship is solved by this method, tuned mass dampers mass ratio parameters are calculated using the equivalent mass. According to the analysis, tuned mass dampers has 31dB vibration absorption effect at 13.4Hz when the mass ratio is 0.05, it also has certain control effect at 10Hz and 18.8Hz, the control effect is 3dB and 2dB respectively, the overall control frequency band is flat and robust.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

Fibroblast activation protein (FAP) is a serine protease characterized by its high expression in cancer-associated fibroblasts (CAFs) and near absence in adult normal tissues and benign lesions. This unique expression pattern positions FAP as a prospective biomarker for targeted tumor radiodiagnosis and therapy. The advent of FAP-based radiotheranostics is anticipated to revolu-tionize cancer management. Among various types of FAP ligands, peptides and antibodies, have shown advantages over small molecules, exemplifying prolonged tumor retention in human volunteers. Within its scope, this review summarizes the recent research progress of the FAP radiopharmaceuticals based on antibodies and peptides, on tumor imaging and therapy. Additionally, it incorporates insights from recent studies, providing valuable perspectives on the clinical utility of FAP-targeted radiopharmaceuticals.

The modifications in planting structure and continuous land use adjustments have significant implications for the structure, diversity, and functioning of arthropod communities in farmland landscapes, particularly regarding the biological control of pest insects by natural enemy species. Therefore, there is an urgent need to comprehensively and accurately assess insect community diversity in croplands. In this study conducted between 2022-2023, we utilized Malaise traps and sweep netting to collect insects from three different double-cropping paddy fields. We extracted DNA from preservative ethanol of Malaise traps and tissue samples of selected parasitoid wasps, followed by amplification using DNA barcoding primers to prepare high-throughput sequencing libraries. As a result, we annotated a total of 4956 operational taxonomic units (OTUs) belonging to 174 genera and 32 families of parasitoid wasps. Our findings demonstrate that the ethanol filter method efficiently captures a wide range of information diversity. However, it demonstrates a lower resolution and may result in a reduction of species abundance. Furthermore, we have identified additional insect species in the parasitoid samples. This demonstrates that high throughput sequencing from adult parasitoid wasps can effectively detect host specie, enabling a comprehensive understanding of host species and providing novel insights into food web construction.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

Muscle fatigue caused by using staplers affects the surgical procedures of surgeons. Compared to manual staplers, electric staplers decrease the muscle fatigue by replacing repeated gripping and releasing with automatic model. Still powered by the battery, the electric staplers are confronted with new operation fatigue due to the extra weight of the battery. The weight and manual operation of the electric stapler can cause user's muscle fatigue. To tackle the unsettled fatigue issue, the study is to propose a new design method to offset the influence of extra weight of the battery attached to the electrical stapler by changing the opening and closing of the stapler end clamp to electric control. The purpose of this study is to verify whether the design of this electric stapler can offset the impact of weight. Experiments are set up to test the feasibility of the design on 12 male Chinese surgeons. The muscle fatigue is indicated by measuring the EMG (electromyography) signal, and the stapler's working effect is indicated by measuring the end movement of the stapler. The result shows the new-designed stapler reduce the operation fatigue, counteracting the impact of the battery weight.

As the lifespan of porous asphalt pavement extends, it invariably experiences performance degradation and an increase in tire/pavement noise compared with the original surface when it is newly built. To understand the medium-term performance of porous asphalt pavement during service and reveal the influence of different pavement performance indicators on tire/pavement noise generation, a seven-year continuous observation and data analysis study was conducted. Porous asphalt with different designed material parameters was taken into account, including thin-layer porous asphalt overlay with a maximum nominal aggregate size of 10mm (PUC-10), porous asphalt with a maximum nominal aggregate size of 13mm (PAC-13), and a two-layer porous asphalt incorporating both PUC-10 and PAC-13 (PUC-10+PAC-13). Using automated pavement technology testing equipment, key performance indexes, including damage rate (DR), rut depth (RD), international roughness index (IRI), and sideway force coefficient (SFC), were measured and calculated. The on-board sound intensity (OBSI) method was used to test noise levels in three types of porous asphalt pavement structures and on a dense graded easy compact asphalt concrete (ECA) for comparison. The progressions of the medium-term performances were analyzed according to the measured results. The correlations between tire/pavement noise levels and testing speed, testing lane, pavement structure, and road condition indicators were investigated by regression. The research results revealed that the DR and SFC of the three types of porous asphalt pavement displayed more significant attenuation in the service period, while the IRI and RD showed small changes. Among them, the SFC demonstrated significant attenuation over the first 4 years, decreasing between 13.8% and 17.0%. From the 3-7 years of operation, the transverse crack disease in porous asphalt pavement progressed rapidly. The three porous asphalt pavement structures tested exhibited commendable noise reduction capabilities. Compared to ECA, the OBSI noise levels of these structures were lower by 2.09 dB, 1.53 dB, and 2.88 dB, respectively. Compared to other pavement condition indicators, RD had a more significant impact on the OBSI value of the PUC-10 porous asphalt pavement. For the PUC-10+PAC-13 porous asphalt pavement, there was a significant linear relationship between the OBSI value and SFC, mainly due to polishing of the coarse aggregate surface. It leads to a decrease of the micro-texture, which lies in increasing tire/pavement noise at high-frequency ranges and decreasing SFC. This study will have guiding significance for the research of the attenuated law and durability improvement of porous asphalt tire/pavement noise.

The development of solid-state forms of drugs is an effective mean of solubility enhancement. In this study, two polymorphs named form C, form D, and two co-crystals of sorafenib (SF) with oxalic acid (SF-OA) and malonic acid (SF-MA), by evaporation and slurry method, have been developed and characterized. The single-crystal X-ray diffraction results showed that the structure of form C was similar to of form I. It had similar cellular parameters, but different arrangement of stacking due to π-π conjugation. The drug molecules in SF-OA underwent torsional folding through four hydrogen bonds of intermolecular and intramolecular. The solubility performance of solid-state forms improved significantly. Compared with form I, form C and form D were 1.59, 1.49 times at pH 1.2 HCl, 1.59, 1.87 fold at pH 6.8 PBS. In particular, the SF-OA and SF-MA increased the apparent solubility of SF at pH 1.2 by 8.3 and 6.4 times, at pH 6.8 by 4.0 and 4.5 times respectively. The dissolution mechanisms were analyzed. New solid-state forms showed strong stability at storage conditions of 40 °C/75% RH and 60 °C/0% RH. Notably, the crystal of SF preferred to transform in mixed solvents, and the formation of co-crystals confirmed the ∆pKa rule.

In this paper, four lithological parameters, i.e. thermal conductivity, particle size, porosity and saturation, are investigated by combining experimental observations with numerical simulations to study the influence laws and mechanisms of action on the combustion process of methane hydrate sediments. The variation of combustion characteristics parameters such as flame height, effective combustion ratio and dimensionless discharge water mass with the lithological parameters are studied. In addition, the combustion mechanism of lithologic parameters on methane hydrate deposits is revealed. Combining the experimental results and simulation calculations, to optimize the combustion of methane hydrate sediments, it is recommended to use methane hydrate sediment samples with high saturation and low thermal conductivity, while the oxidant concentration and porosity of methane hydrate sediment samples should be increased.

Photodynamic therapy (PDT) has garnered significant attention in the fields of cancer treatment and drug-resistant bacteria eradication due to its non-invasive nature and spatiotemporal controllability. Iridium complexes have captivated researchers owing to their tunable structure, exceptional optical properties, and substantial Stokes displacement. However, most of these complexes suffer from aggregation-induced quenching, leading to diminished luminous efficiency. In contrast to conventional photosensitizers, photosensitizers exhibiting aggregation-induced luminescence (AIE) properties retain the ability to generate a large number of reactive oxygen species when aggregated. To overcome these limitations, we designed and synthesized a novel iridium complex named Ir-TPA in this study. It incorporates quinoline triphenylamine cyclomethylated ligands that confer AIE characteristics for Ir-TPA. We systematically investigated the photophysical properties, AIE behavior, spectral features, and reactive oxygen generation capacity of Ir-TPA. The results demonstrate that Ir-TPA exhibits excellent optical properties with pronounced AIE phenomenon and robust capability for producing singlet oxygen species. This work not only introduces a new class of metal iridium complex photosensitizer with AIE attributes but also holds promise for achieving remarkable photodynamic therapeutic effects in future cellular experiments and biological studies.

As one of the important wastes, waste PET pollutes human living and natural environment seriously. PET is an important solid waste that needs to be recycled at present. The complete degradation of PET was realized at low temperature. The lipophilic hydrophobic membrane was formed on the surface of stainless steel mesh (SSM) by a simple dip coating method, and the oil-water separation material was successfully prepared. Due to the load of degradation products, the surface roughness of SSM increased from 19.09 μm increased to 62.33 μm. The surface changed from hydrophilic to hydrophobic, and the water contact angle increased to 123o. The oil-water separation flux of modified SSM is 9825 L/(m2·h) and the separation efficiency is 98.99%. The modified SSM has good reuse performance. This hydrophobic modification method can also be used to modify other porous substrates, such as activated carbon, filter paper, foam, and other materials. In this study, the porous substrate modified by the degradation product of waste PET was used to prepare oil-water separation materials, which not only solved the problem of white pollution, but also reduced the dependence on non renewable resources in the conventional preparation methods of oil-water separation materials. The research provided new raw materials and methods for the industrial production of oil-water separation materials, and had important application prospects.

The electronic, optical, and magnetic properties of Nd-doped ZnO systems were calculated using the DFT/GGA+U method. According to the results, the Nd dopant causes lattice parameter expansion, negative formation energy, and bandgap narrowing, resulting in the formation of an n-type degenerate semiconductor. Overlapping of the generated impurity and Fermi levels results in a significant trap effect that prevents electron-hole recombination. The absorption spectrum demonstrates a redshift in the visible region and improved intensity, leading to enhanced photocatalytic performance. The Nd-doped ZnO system displays ferromagnetic, with FM coupling due to strong spd-f hybridization through magnetic exchange interaction between the Nd-4f state and O-2p, Zn-4s, and Zn-3p states. These findings imply that Nd-doped ZnO may be a promising material for DMS spintronic devices.

This study entailed the design and analysis of a 400 m-class underwater glider operated by a bladder-type buoyancy engine. The underwater glider was designed for high-speed movement with a maximum velocity of 2 knots. The shape of the hull was designed to reduce water resistance using the Myring hull profile equation. The reliability was verified by performing simulations using resistance coefficients. The relationship between the control value of the ballast discharged from the buoyancy engine and the glider's speed according to the path angle was analyzed. Further, the relationship between the optimal glide angle and the design control value of the ballast was derived, and the optimal glider speed was estimated accordingly. Based on the analysis results, a bladder-type buoyancy engine was developed, and the maximum speed of the tested underwater glider was measured via sea trials.

Neurogenesis in the adult brain plays a major role in the cognitive ability of animals including learning and memory. Poria cocos (Schw.) Wolf (P. cocos) has been known as a traditional Chinese edible medicinal herb with the potential effect to improve learning and memory. However, the effect mechanisms are still elusive. In this study, significant neuronal differentiation-promoting activities of the ethanol extracts of P. cocos (EEPC) were tested in Neuro-2a cells and mouse cortical neural stem/progenitor cells (NSPCs). Subsequently, 97 compounds of EEPC were identified using UHPLC-Q-Exactive-MS/MS. After investigation of neuronal differentiation-promoting activities of 4 major compounds (Ethyl palmitoleate, L-(-)-Arabitol, Choline and Adenosine), only Choline has significant neuronal differentiation-promoting activity. In summary, we investigated the neuronal differentiation-promoting activity and chemical compositions of EEPC, the study of the neuronal differentiation-promoting effect of ether extract of P. cocos indicated P. cocos’s positive effect on learning and memory functions. This is the first investigation of the neuronal differentiation-promoting effect of ether extract of P. cocos based on similar research references.

The menopausal transition often accompanies distressing manifestations, including vasomotor symptoms, sleep disruptions, and depressive syndrome. Omega-3 fatty acids have emerged as a potential intervention to alleviate these symptoms. This review aimed to comprehensively assess the impact of omega-3 supplementation on vasomotor symptoms, sleep quality, and depression among postmenopausal women. We conducted a systematic search focusing on randomized control trials across the Cochrane Library, Web of Science, PubMed, CINAHL, EMBASE, and SCOPUS databases from inception to August 2023. Among the initial pool of 163 studies, 9 studies met the inclusion criteria and were incorporated into this review. Four studies suggested potential benefits of omega-3 intake for improving hot flashes and night sweats. Sleep quality outcomes displayed heterogeneity across the studies. Incorporating diverse scales such as the Hamilton Depression Rating Scale-21, the Patient Health Questionnaire depression scale, and Generalized Anxiety Disorder-7 for depression outcomes, the review found inconclusive evidence on omega-3's impact on depression. Overall, the combined analysis of these studies did not provide substantial evidence to support the efficacy of omega-3 fatty acids in improving vasomotor symptoms, sleep quality, and depression. Further well-designed RCTs with larger participant groups are crucial to validate and generalize these results.

The first appearance of viruses can date back to the late last century. As an effective form of malware, viruses reside in the permanent storage of target hosts. Before a virus can execute, that must load into memory from the persistent storage included in the associated file. Due to the reliable destructive power of viruses, many mechanisms have been developed to defend computer systems against these hazardous threats. Antivirus software is one of the most famous and popular among these mechanisms. Most antivirus software uses static analysis (signature-based) technology on files stored in permanent storage, such as hard disks or USB flashes, to detect viruses hidden in files. Fileless malware was developed to enhance the survivability of malware by circumventing detection. Fileless malware only exists in the target hosts’ memory, not files. Antivirus software cannot even access the fileless malware code, much less analyze it, since it may be performed in memory directly without needing to load it from a disk. As a result, it is difficult for an antivirus engine to defend a system against fileless malware attacks. This paper proposes a kernel-based solution called Check-on-Execution (CoE) to detect fileless malware on a Linux system. When a program is going to execute a piece of code in a writable and executable memory area of a process, CoE suspends the code execution first. Coe retrieves the code from memory, packs the code with an ELF header to create an ELF file, and uses VirusTotal to check the file to prevent a Linux system from executing fileless malware. Experimental results show that CoE noticeably enhances the ability of a Linux system to defend itself again fileless malware. CoE is also suitable for protecting a system from shell code injection attacks, such as buffer and heap overflow attacks. It is capable of handling even packed malware. But in this paper, we only focus on fileless malware.

The risk of lung exposure to silica nanoparticles (SiNPs) and related lung inflammatory injury is increasing with the wide application of SiNPs in a variety of industries. A growing body of research has revealed that cyclooxygenase (COX)-2/ prostaglandin E2 (PGE2) up-regulated by SiNPs toxicity has a role during pulmonary inflammation. The detailed mechanisms underlying SiNPs-induced COX-2 expression and PGE2 synthesis remain unknown. The present study aims to dissect the molecular components involved in COX-2/PGE2 up-regulated by SiNPs in human pulmonary alveolar epithelial cells (HPAEpiCs) which are one of the major targets while SiNPs are inhaled. In the present study, we demonstrated that SiNPs induced COX-2 expression and PGE2 release, which were inhibited by pretreatment with a reactive oxygen species (ROS) scavenger (edaravone) or the inhibitors of proline-rich tyrosine kinase 2 (Pyk2, PF-431396), epidermal growth factor receptor (EGFR, AG1478), phosphatidylinositol 3‑kinase (PI3K, LY294002), protein kinase B (Akt, Akt inhibitor VIII), p38 mitogen-activated protein kinase (MAPK) (p38 MAPK inhibitor VIII), c-Jun N-terminal kinases (JNK)1/2 (SP600125), Forkhead Box O1 (FoxO1, AS1842856), and activator protein 1 (AP-1, Tanshinone IIA). In addition, we also found that SiNPs induced ROS-dependent Pyk2, EGFR, Akt, p38 MAPK, and JNK1/2 activation in these cells. These signaling pathways induced by SiNPs could further cause c-Jun and FoxO1 activation and translocation from the cytosol to the nucleus. AP-1 and FoxO1 activation could increase COX-2 and PGE2 levels induced by SiNPs. Finally, the COX-2/PGE2 axis might promote the inflammatory responses in HPAEpiCs. In conclusion, we suggested that SiNPs induced COX-2 expression accompanied by PGE2 synthesis mediated via ROS/Pyk2/EGFR/PI3K/Akt/p38 MAPK- and JNK1/2-dependent FoxO1 and AP-1 activation in HPAEpiCs.

The Oriental ratsnake Ptyas mucosa is a common non-venomous snake of the colubrid family, with a wide geographic range spanning much of South and Southeast Asia. P. mucosa is widely cultivated dut to it used in traditional medicine, scientific research, and handicrafts. Therefore, genome resources could play an important role in the efficacy of traditional medicine and the analysis of the living environment of the species. We collected a snake sample in Hezhou, Guangxi, China, which was identified as P. mucosa by morphological identification. Here we present a highly continuous P. mucosa genome with a genome size of 1.74Gb. The scaffold N50 length is 9.57Mb and the maximal length of scaffold is 78.3Mb, the P. mucosa genome has a CG content of 37.9% and the integrity of the gene reached 86.6%.Assembled using long-reads, the total length of the repeat sequence in the genome reached 735 Mb, and its repeat content was as high as 42.19%. A total of 24,869 functional genes were annotated. This study will assist in the understanding of the P. mucosa, and also provide a basis for medicinal research.

Abstract: The traditional model of closed circuit ball milling systems has been used for several decades, however, if the classifier of the closed circuit ball mill system performs the duties of both pre-classification and check-classification, the characterization error of the traditional model is large. To address this problem, a new model is obtained by modifying and supplementing the traditional one. The most important feature of the new model compared to the traditional model is that the circulating load is considered to be the fresh feed for the entire system rather than the ball mill. The error between the slurry level height calculated using the traditional model and the actual is 52.31%, which is 13.77 times higher than that of the new model. When the relative capacity varies greatly, that of the ball mill calculated by the traditional model fluctuates between 0.95 and 1.15, while the new model is 0.6 to 1.4. The new model has a higher accuracy than the traditional model in characterizing the production status of the grinding system, which is of some significance for industrial production.

Aiming to reveal the kinetic characteristics of ceramic ball grinding of fine magnetite comprehensively, two types of ceramic balls ground with the same filling rate and total weight as steel balls were researched. The results show that the breakage rate of ceramic ball grinding is only half of that of steel ball grinding with the same media filling rate. With the same total media weight and the feed size less than 0.212 mm, the breakage rate of the ceramic ball grinding approaches the steel ball grinding and is 21.43% higher than that of the steel ball grinding. The main crushing form of magnetite changed from impact to abrasion in ceramic ball grinding compared with steel ball grinding, which significantly affected the value of the zero-order output constant a. Consequently, there is a noticeable difference in the variation of the parameter β related to the fines generation rate of the ceramic ball grinding compared with the steel ball grinding.

(1) Background: This retrospective study aimed to compare the efficacy and safety of one-stage computed tomography (OSCT)- to that of two-stage computed tomography (TSCT)-guided localization for the surgical removal of small lung nodules. (2) Methods: We collected data from patients with ipsilateral pulmonary nodules who underwent localization before surgical removal at Veteran General Hospital Kaohsiung between October 2017 and January 2022. The patients were divided into the OSCT and TSCT groups. (3) Results: We found that OSCT significantly reduced the localization time and risky time compared to TSCT, and the success rate of localization and incidence of pneumothorax were similar in both groups. However, the time spent under general anesthesia was longer in the OSCT group than in the TSCT group. (4) Conclusions: The OSCT-guided approach to localize pulmonary nodules in hybrid operation room is a safe and effective technique for the surgical removal of small lung nodules.

Modern power system integrates more and more new energy and use a large number of power electronic equipment. This makes it face more challenges in online optimization and real-time control. Deep reinforcement learning(DRL) has the ability of processing big data and high-dimensional features, as well as the ability of independently learning and optimizing decision-making in complex environments. In this paper, we explore DRL based online combination optimization method of grid section for large complex power system. In our method, to improve the convergence speed of the model, we propose to discretize the output action of the unit and simplify the action space. We also design a reinforcement learning loss function with strong constraints to further improve the convergence speed of the model and facilitate the algorithm to obtain the stable solution. Moreover, to avoid the local optimal solution problem caused by the discretization of the output action, we propose to use the annealing optimization algorithm to make the granularity of the unit output finer. We verify our method on IEEE 118-bus system. The experimental results show that our model has fast convergence speed and better performance, and can obtain stable solutions.

Background Coronary artery disease (CAD) is a widely recognized cardiovascular disease that is considered the leading cause of death worldwide, affecting people on a global scale. Percutaneous coronary intervention (PCI), which involves procedures such as balloon angioplasty or stenting, plays an important role in opening blocked arteries and minimizing damage to the cardiac muscle. While the use of drug-eluting stents (DESs) has significantly reduced the occurrence of coronary restenosis, the problem of in-stent restenosis (ISR) continues to pose a significant clinical challenge. Gaining a deeper understanding of the clinical predictors associated with ISR is vital for early detection and appropriate treatment. Hence, this study aimed to evaluate the clinical predictors of ISR specifically in Taiwanese patients. Methods We conducted a single-center, retrospective case-control study, enrolling 517 CAD patients undergoing previous coronary stenting and stable angina with positive stress test or acute coronary syndrome (ACS) during follow-up between January 2019 and December 2022 at National Taiwan University Hospital. The patients were categorized into two groups: the ISR group, consisting of individuals who received drug-coated balloon (DCB) treatment (n=177), and the non-ISR group, comprising patients who did not receive DCB treatment (n=340). To gather relevant data, we meticulously reviewed the medical records and analyzed the findings from coronary angiography to assess the clinical characteristics of the patients. Results Patients with three-vessel disease (3VD) exhibited a higher prevalence of underlying diseases and were more likely to be taking aspirin and clopidogrel. Moreover, our analysis revealed that age (adjusted odds ratio [aOR] 1.02, 95% confidence interval [CI] 1.00 - 1.04, p = 0.037) and the presence of 3VD (adjusted odds ratio [aOR] 2.15, 95% confidence interval [CI] 1.03 - 4.46, p = 0.039) were significantly associated with an increased risk of coronary ISR. Conclusions Older age and 3VD were the independent predictors of coronary ISR in CAD patients receiving coronary stent implantation.

Against the backdrop of global climate change, the frequency of drought events is increasing, leading to significant impacts on human society and development. Therefore, it is crucial to study the propagation patterns and trends of drought characteristics over a long-time scale. The main objective of this study is to delineate the dynamics of drought characteristics by examining their propagation patterns in China from 1951 to 2020. In this study, precipitation data from meteorological stations across mainland China were used. A comprehensive dataset consisting of 700 stations over the past 70 years was collected and analyzed. To ensure data accuracy, the GPCC database was employed for data correction and gap filling. Long-term drought evolution was assessed using both the SPI-12 and SPEI-12 indices to detect drought characteristics. Two Moran indices were applied to identify propagation patterns, and the MK analysis method along with the Theil-Sen slope estimator were utilized to track historical trends of these indices. The findings of this study reveal the following key results: (i) Based on the SPI-12, the main areas of China that are prone to drought are mostly concentrated around the Hu Huanyong Line. Indicating a tendency towards drying based on the decadal change analysis. (ii) The distribution of drought-prone areas in China, as indicated by the SPEI-12, is extensive and broadly distributed, with a correlation to urbanization and population density. These drought-prone areas are gradually expanding. (iii) Between 2010 and 2011, China experienced the most severe drought event in nearly 70 years, affecting nearly 50% of the country's area with a high degree of severity. This event may be attributed to atmospheric circulation variability, exacerbated by the impact of urbanization on precipitation and drought. (iv) The frequency of drought occurrence in China gradually decreases from south to north, with the northeast and northern regions being less affected. However, areas with less frequent droughts experience longer and more severe drought durations. In conclusion, this study provides valuable insights into the characteristics and propagation patterns of drought in China, offering essential information for the development of effective strategies to mitigate the impacts of drought events.

High-efficiency rock breaking by hydraulic jetting is the key to radial horizontal drilling technology. In order to improve the drilling efficiency of hydraulic jet rock breaking in radial horizontal wells, based on LS-Dyna display dynamics, a numerical simulation model of single nozzle jet rock breaking is established to analyze the influence of different nozzle parameters on rock breaking effect. Then, the numerical simulation model of the spin multi-nozzle jet bit is established, and the influence of different rotation speeds on the rock breaking effect of the jet bit is analyzed. Finally, the rock breaking drilling characteristics of the spin multi-nozzle jet bit and the conventional multi-nozzle jet bit are compared and analyzed. The results show that when the jet impacts the rock surface, the larger the inclination angle is, the larger the rock breaking width formed by the jet is. The smaller the dip angle, the greater the rock breaking depth. When the inclination angle is greater than 60 °, it is difficult to meet the needs of reaming. The width and depth of the nozzle gradually increase with the increase of the diameter. When the nozzle diameter is greater than 1.3mm, the growth rate of rock breaking depth begins to decrease. The optimum nozzle diameter is 1.3 mm. When v = 50m / s, the damage caused by the jet to the rock surface is very small, because the condition of rock fracture is not reached at this time. This shows that there is a critical value of the water jet impact velocity, and only when the velocity is reached, the rock will break. When the velocity is v = 150m / s, v = 200m / s, v = 250m / s, v = 300m / s, the rock breaks. At the same time, the higher the speed, the higher the degree of rock fracture, the greater the fracture depth, the greater the fracture area, the better the fracture effect. The tangential and radial velocity of the jet increases the shear and tensile failure rate of the sample, and improves the rock breaking efficiency of the jet, which has certain guiding significance for improving the rock breaking drilling efficiency of radial horizontal well drilling.

With the increasing demand for medicinal plants and the increasing shortage of resources, improving the quality and yield of medicinal plants and making more effective use of medicinal plants has become an urgent problem to be solved. In the process of growth and development of medicinal plants, due to the threat of various adversity, there are problems such as nutrient loss and yield decline. Using traditional chemical pesticides to control the stress resistance of plants will cause serious pollution to the environment and even endanger human health. Therefore, it is necessary to find suitable pesticide substitutes from natural ingredients. As an important part of the microecology of medicinal plants, endophytes can promote the growth of medicinal plants, improve the stress resistance of hosts, and promote the accumulation of active components of hosts. Because it has a more positive and direct impact on the host, and can metabolize rich medicinal ingredients, so researchers pay attention to it. This paper reviews the research in recent five years, aiming to provide ideas for improving the quality of medicinal plants, developing more microbial resources, exploring more medicinal natural products, and providing help for the development of the research on medicinal plants and endophytes.

In this study, we present more than 8 years of observations of the quasi-16-day wave (Q16DW) in the mesosphere and lower thermosphere (MLT) wind at middle latitudes observed by the Mengcheng (33.4°N, 116.5°E) meteor radar. The long-term variation in amplitudes calculated from the data between April 2014 and December 2022 shows enhanced wave activity during winter and early spring (near equinox) and suppressed wave activity during the summer. The Q16DWs are relatively weak in the meridional wind. During the winter months, the Q16DWs in the zonal component exhibit a burst below 85 km, and their amplitudes reach up to 10 m/s. In the early spring, the Q16DWs strengthen above 90 km with amplitudes in excess of 12 m/s. The phase differences between the zonal and meridional components of the Q16DW are, on average, slightly smaller than 90°, suggesting the existence of orthogonal relationships between them. During strong bursts, the periods of the Q16DW in winter range between 15 and 18 d, whereas in winter, the periods tend to be more diffuse. The wintertime Q16DW is amplified, on average, when the zonal wind shear peaks, suggesting that barotropic instability may be one source of Q16DW. Q16DW amplitudes exhibit considerable interannual variability; however, a relationship between the 11-year solar cycle and the Q16DW is not found.

This study examined the relationship among the three domains of executive function (EF; cognitive shifting, inhibitory control, and working memory) to test the applicability of the unity-diversity model in preschoolers using both behavioral and fNIRS approaches. Altogether 58 Chinese preschoolers (34 boys, 24 girls, Mage = 5.86 years, SD = 0.53, Age range = 4.83-6.67 years) were administered the Dimensional Card Change Sort (DCCS), go/no-go, and missing scan task. Their brain activations in the prefrontal cortex during the tasks were examined using fNIRS. First, the behavioral results indicated that the missing scan task scores (working memory) correlated with the DCCS (cognitive shifting) and go/no-go tasks (inhibitory control). But the latter two did not correlate with each other. Second, the fNIRS results demonstrated that the prefrontal activations during the working memory task correlated with those in the same regions during the cognitive shifting and inhibitory control tasks. Still, the latter two did not correlate. The behavioral and neuroimaging evidence jointly indicates that the unity-diversity model of EF does apply to Chinese preschoolers.

Genome-scale metabolic model (GEM) is a powerful tool for interpreting and predicting cellular phenotypes under various environmental and genetic perturbations. However, GEM only consid-ers stoichiometric constraints, and the simulated growth and product yield values will show a monotonic linear increase with increasing substrate uptake rate, which deviates from the experi-mentally measured values. Recently, the integration of enzymatic constraints into stoichiometry-based GEMs was proven to be effective in making novel discoveries and predicting new engineer-ing targets. Here we present the first genome-scale enzyme-constrained model (eciCW773) for Corynebacterium glutamicum reconstructed by integrating enzyme kinetic data from various sources using ECMpy workflow based on the high-quality GEM of C. glutamicum (obtained by modifying the iCW773 model). The enzyme-constrained model improved the prediction of pheno-types and simulated overflow metabolism, while also recapitulating the trade-off between biomass yield and enzyme usage efficiency. Finally, we used eciCW773 to identify several gene modifica-tion targets for L-lysine production, most of which agree with previously reported genes. This study shows that incorporating enzyme kinetic information into the GEM enhances the cellular phenotypes prediction of C. glutamicum, which can help identify key enzymes and thus provide reliable guidance for metabolic engineering.

Infectious keratitis (IK) represents a major cause of corneal blindness. This study aims to investigate the demographics, risk factors, microbiological characteristics and antibiotic susceptibility patterns of IK in Taiwan over the past 15 years. A retrospective population-based study was conducted using the Chang Gung Research Database. Patients with IK were identified by diagnostic codes for corneal ulcer from 2004 to 2019. Of 7807 included subjects, 45.2% of patients had positive corneal cultures. The proportion of contact lens-related IK declined, while that of IK related to systemic diseases grew. The percentage of isolated gram-positive bacteria surpassed that of gram-negative bacteria in the 15-year period. The prevalence of Pseudomonas aeruginosa showed a decreasing trend (p = 0.004), whereas coagulase-negative Staphylococcus (CNS) and Propionibacterium species were increasingly detected (p &lt; 0.001). Overall, the trend of antibiotic susceptibility of both gram-positive and gram-negative bacteria did not change throughout the study period. The susceptibility to the test antibiotics maintained over 90% in gram-negative isolates during 15 years. Vancomycin preserved 100% susceptibility to all gram-positive isolates. Since most tested antibiotics exhibited stable susceptibility over decades, this study reinforced that fluoroquinolones and fortified vancomycin continue to be good empiric therapies for treating bacterial keratitis in Taiwan.

Synthetic cannabinoids are a series of synthetic substances that mimic the effects of natural cannabinoids and produce a much stronger toxicity than natural cannabinoids, which have become the most abused family of new psychoactive substances. A solid-phase extractive-liquid chromatography-triple quadrupole/linear ion trap mass spectrometry method was developed to determine 11 synthetic cannabinoids in rat urine. The factors affecting recovery were optimized, and Oasis HLB was selected to extract synthetic cannabinoids simultaneously. The results showed that the linear correlation coefficients of the synthetic cannabinoids ranged from 0.993 to 0.999, and the limit of quantitation ranged from 0.01 to 0.1 ng/mL, and the spiked recoveries ranged from 69.90% to 118.39%. This method has the advantages of good purification ability, simple operation, and good reproducibility, and can be used for the high sensitivity analysis of various synthetic cannabinoids in urine.

Grafting is an effective way to increase plant tolerance to biotic and abiotic stressors, it is widely used in watermelon production. However, grafting is labor intensive due to the additional time is required, such as the management of rootstock regrowth. This study used a new grafting tool to destroy (remove) the epidermis of pumpkin and bottle gourd rootstock cotyledon base during grafting, we called this a new grafting method. Compared with the traditional grafting (100%), the new grafting method had significantly lower rate of rootstock regrowth (2-23%), higher watermelon scion dry weight and leaf area. In addition, the time used for the new hole insertion and one cotyledon grafting method to destroy (remove) the epidermis of rootstock cotyledon base (4.2 s/plant, 4.2 s/plant) is significantly shorter than the time required to remove the rootstock regrowth manually in the traditional grafting (9.3 s/plant, 8.8 s/plant). Thus, this study developed a new grafting method for watermelon to inhibit rootstock regrowth and enhance scion growth, and this new method is cost-effective for grafted watermelon seedlings.

The effect of rare earth Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results showed that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites, and significantly improve the toughness of weld metal. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. However, excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties, and the corresponding values were 835MPa of tensile strength and 72 J of impact toughness. These findings suggest that the control of Pr6O11 can be an effective way to improve the impact toughness of weld metal.

Advanced paternal age at fertilization has been suggested to be a risk factor for neurodevelopmental, psychiatric and other disorders in offspring. One emerging hypothesis suggests that altered offspring phenotype is linked with age-related accumulation of epigenetic changes in the sperm of fathers. Given that paternal age is increasing in the developed world, understanding aging-related epigenetic changes in sperm is needed as well as environmental factors that modify such changes. In this study, we characterize age-dependent changes in sperm DNA methylation profiles between young pubertal (postnatal day (PNDs) 65) and mature (PND120) Wistar rats. We also analyze these changes in rats exposed perinatally to 0.2 mg/kg of ubiquitous environmental xenobiotic 2,2’,4,4’-tetrabromodiphenyl ether (BDE-47). Reduced representation bisulfite sequencing (RRBS) libraries were prepared from caudal epididymal sperm DNA and differentially methylated regions (DMRs; ≥ 10x coverage depth, ≥ 3 CpGs per cluster, ≥ 5% methylation change, q < 0.05) were identified via MethPipe package. In control animals, 5,319 age-dependent DMRs were identified, with 99.3% DMRs hypermethylated in mature animals compared to young pubertal rats. These age-related DMRs were enriched for functional categories essential for embryonic development, such as pattern specification, forebrain and sensory organ development, Hippo and Wnt pathways. Age-related changes in sncRNA, reported in different study, target similar list of genes and biological categories.In BDE-47 exposed rats, sperm DNA methylation was higher in young pubertal and lower in mature animals when compared to controls, which resulted in a significant attenuation in the number of age-dependent DMRs (N = 189) identified in the exposed group. In conclusion, our results indicate that the natural aging process has profound effects on sperm methylation levels and this effect may be modified by environmental exposures. Moreover, our results further support the role of epigenetic mechanisms as a likely link betwen paternal age and offspring health and development.

With the unceasing advancement in wide-bandgap (WBG) semiconductor technology, the minimal reverse-recovery charge Qrr and other more powerful natures of WBG transistors enable totem-pole bridgeless PFC to become a dominant solution for energy storage systems (ESS). This paper focuses on design and implementation of a control structure for a totem-pole boost PFC with newfangled enhancement-mode Gallium Nitride (eGaN) FETs, not only to simplify the control implementation, but also to achieve high power quality and efficiency. The converter is designed to convert a 90-264-VAC input to a 385-VDC output for a 2.6-kW output power. Lastly, to validate the methodology, an experimental prototype is characterized and fabricated. The uttermost efficiency at 230 VAC attains 99.14%. The lowest total harmonic distortion in the current (ITHD) at high line condition (230 V) reaches 1.52% while the power factor gains 0.9985.

Laser shock peening as an innovative surface treatment technology can effectively improve the fatigue life, sur-face hardness, corrosion resistance, and residual compressive stress. Compared with the laser shock peening, the warm laser shock peening (WLSP) is a new surface treatment technology to improve materials’ surface performances, which takes advantage of thermal mechanical effects on stress strengthening and micro-structure strengthening, results in more stable distribution of the residual compressive stress under heating and cyclic loading process. In this paper, the microstructure of GH4169 nickel super-alloy processed by WLSP technology with differ-ent laser parameters were investigated. The proliferation and tangling of dislocations in GH4169 were observed and the dislocation density increased after WLSP treatment. The influences of different treatment by LSP and WLSP on the microhardness distribution of the surface and along cross-sectional depth were investi-gated. The microstructure evolution of the GH4169 alloy being shocked with WLSP were studied by TEM. The effect of temperature on the stability of high temperature microstructure and properties of GH4169 alloy WLP was investigated.

Liquid metal alloy, incorporated with microfluidic manipulation, has become a promising candidate for flexible resistive sensor array (RSA) that can imitate the functions of human skin. One advantage of RSA with shared rows and shared columns is to reduce the number of wires from M × N to M + N (rows: M and columns: N) and hence to greatly lessen the complexity and burden on the electrical system. The associated drawback is the crosstalk effect between adjacent elements during measurement. Although many literatures have reported several methods to resolve this limitation, almost all of them focus only on the high resistance value (≥100 Ω) RSA. There is a lack of detailed experimental data that addresses low resistance RSA with sensing elements below 100 Ω. Here, we aim to fill the gap of this field. We established two common RSA readout systems, i.e. zero potential methods (ZPM) (setting non-scanned-sampling-electrode zero potential (S-NSSE-ZP) and setting non-scanned-sampling-electrode zero potential with amplifier (S-NSSE-ZP-A)) and to compare their performances in low resistance value (≤100 Ω) RSA. For ideal resistor RSA, the measurement results show that S-NSSE-ZP has at least one time higher error than S-NSSE-ZP-A.

We report fabrication of crystalline microresonators of high quality (Q) factors with a controllable wedge angle on lithium niobate on insulator (LNOI). Our technique relies on femtosecond laser assisted chemo-mechanical polish which allows us to achieve ultrahigh surface smoothness as critically demanded by high Q microresonator applications. We show that by refining the polish parameters, Q factors as high as 4.7 × 10⁷ can be obtained and the wedge angle of the LNOI can be continuously tuned from 9° to 51°.

In this study, an extracellular metalloprotease from Pseudoalteromonas sp. H2 was purified and identified. The EH2 maintained more than 80% activity over a wide pH range of 5-10 and the stability was also nearly independent of pH. More than 65% of activity was detected in a wide temperature of 20-70℃. The high stability of the protease in presence of different surfactants and oxidizing agent was also observed. Moreover, we also investigated the antioxidant activities of the hydrolysates generated from porcine and salmon skins collagen by EH2. The results show that salmon skins collagen hydrolysates demonstrated higher DPPH (42.88%±1.85) and hydroxyl radical (61.83%±3.05) scavenging activity compared to those produced with porcine skins collagen. For oxygen radical absorbance capacity, the hydrolysates from porcine skins collagen had higher efficiency (7.72±0.13 μmol·TE/μmol). Even 1 nM mixed peptides can effectively reduce the levels of intracellular ROS. And the two type of substrates exerted the best antioxidant activity when hydrolyzed for 3 hours. Hydrolysis time and type of substrate exerted important effect on the antioxidant property of hydrolysates. This study may have implications for the potential application of marine protease in biocatalysis industry. In addition, the hydrolyzed peptides from meat waste containing beneficial collagen by protease have good antioxidant activity indicating it may be a potential additive in the food processing industry and cosmetics industry.

We report fabrication of a multifunctional photonic integrated chip on lithium niobate on insulate (LNOI), which is achieved by femtosecond laser assisted chemo-mechanical polish. We demonstrate a high extinction ratio beam splitter, a 1 × 6 optical switch, and a balanced 3 × 3 interferometer on the fabricated chip by reconfiguring the microelectrode array integrated with the multifunctional photonic circuit.

Particulate matter is a severe source of atmospheric pollution in urban cities, and it has adverse effects on human health. This study was conducted during the whole year of 2016 to monitor the concentrations of PM₁₀ and PM_2.5 on the Beijing Hanshiqiao wetland and bare land in Beijing to analyze their correlations with meteorological factors and compare the removal efficiency between two land surface types. The results indicated that (1) the PM₁₀ and PM_2.5 concentrations on the bare land were higher than those on wetland as a whole, reaching the highest value both at night and dusk and the lowest value near noon. The average concentration of PM₁₀ was higher in winter (wetland: 137.48 μg·m^-3; bare land: 164.75 μg·m^-3) and spring (wetland: 205.18 μg·m^-3; bare land: 244.85 μg·m^-3) and the concentration of PM_2.5 on the wetland also reached the higher value in winter and spring with the average of 84.52 μg·m^-3 and 98.98 μg·m^-3, whereas, it was higher in spring and summer on the bare land; (2) concentrations of PM₁₀ and PM_2.5 were significantly positively affected by the relative humidity (P < 0.01) and negatively influenced by wind speed (P < 0.05). The relationship between PM₁₀ and PM_2.5 concentrations and temperature was found complicated: it showed a significantly negative correlation (P < 0.01) in winter and spring and was insignificant in autumn, but in summer, only the correlation between the PM₁₀ concentration and temperature on wetland was significant (P < 0.01); (3) the removal efficiencies of PM₁₀ and PM_2.5 followed the order of spring > winter > autumn > summer on the wetland, and the removal efficiency of PM₁₀ was greater than that of PM_2.5. This study is aim to provide practical measures to improve the air quality and facilitate sustainable development in Beijing.