The research on the impact of excavation of underpass tunnels has already had certain results, but there is a lack of research cases of double-line highway tunnels with oblique angles underpass the existing railway tunnels, especially the method of determining the area of the impact of the dynamic and static loads of the new tunnels and existing trains to be enriched by considering them at the same time. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel with oblique angles underpass the Hurong Railway in Wanshoushan. By constructing a three-dimensional finite element model and simulating the application of static tunnel excavation load, dynamic blasting load and dynamic train operation load of the existing tunnel, the overall displacement of the existing tunnel and the settlement value of the bottom plate of the track surface by the static tunnel excavation load were analyzed. Then, the stresses, vibration speeds and displacements of the tunnel due to the dynamic blasting loads and the dynamic train operation loads were obtained. The results show that: the area of influence of the static loads of the new tunnel excavation on the existing tunnel is divided into three types of perturbations presenting strong, weak and slight; the area affected by the blasting dynamic load of new tunnel excavation is a circular domain with the datum point in the tunnel section as the center; the area affected by the dynamic load of train operation in the existing tunnel is an ellipse with the center of the track surface of the existing tunnel as the datum; there is an anomalous shape in the area affected by the blasting dynamic load of new tunnel excavation and the area affected by the dynamic load of train operation in the existing tunnel.

The unsafe behavior of frontline workers at construction sites is the most important cause of construction accidents. This study proposed a comprehensive model of frontline workers' unsafe behaviors based on a systems perspective and used structural equation modeling (SEM) to explore the influence mechanisms between Objective Conditions (e.g., work environment, work climate, task complexity), Safety Management (e.g., safety education and training, safety reward and punishment regulations, safety inspection, safety technology disclosure, safety warning signs), Group Influence (propagation of unsafe behaviors among workers), Personal Perception (subjective judgment of operators on their safety knowledge and skills), and Unsafe Behaviors. Data from 460 frontline workers were collected through questionnaires and the correlation hypotheses were tested using SPSS 26.0 and Amos 26.0 software. The following conclusions were obtained: (1) Objective Conditions directly positively influence Safety Management, Group Influence, and Personal Perception, but indirectly negatively influence Unsafe Behavior; (2) Safety Management not only directly positively affects Personal Perception but also directly negatively affects Unsafe Behavior. However, the direct effect of Safety Management on Group Influence is not significant; (3) Group Influence has a direct positive effect on Unsafe Behavior, but the direct effect on Personal Perception is not significant; (4) The direct effect of Personal Perception on Unsafe Behavior is insignificant. These findings can be used as preliminary data to guide decision-makers or managers in construction companies to develop reasonable management plans to curb unsafe behaviors of frontline workers.

Under high-frequency operating conditions, the high-speed solenoid valve (HSV) experiences energy loss and heat generation, which significantly impact its operational lifetime. Reducing the energy loss of HSV without compromising its opening response characteristics poses a significant challenge. To address this issue, a finite element simulation model of HSV coupled with a current feedback model is constructed to investigate the synergistic effects of dynamic response and energy loss. Predictive models for the opening response time, HSV driving energy, and Joule energy using Back Propagation neural network (BPNN) are established. Furthermore, a multi-objective optimization study on the current driving strategy using Non-dominated Sorting Genetic Algorithm II (NSGA-II) is conducted. After optimization, although there was a 6.24% increase in the opening response time, both HSV drive energy and Joule energy were significantly reduced by 15.67% and 22.49%, respectively. The proposed multi-objective optimization method for HSV driving strategy holds great significance in improving its working durability.

In this paper, we delve into the realm of aspect-level sentiment analysis, a sophisticated analytical task focused on pinpointing and interpreting the sentiment directed towards specific elements within a sentence. Traditional methods in this domain, primarily based on neural networks, have often overlooked the critical role of syntactic structures in sentences. To bridge this gap, we have developed the Syntax-Enhanced Sentiment Graph Network (SentiSyn). This pioneering model represents a significant step forward in aspect-level sentiment analysis, bringing to the forefront the utilization of word dependency relationships to enrich sentiment analysis. SentiSyn stands out by its innovative use of a dependency graph, a tool that meticulously maps out the intricate web of syntactic relationships surrounding a target aspect in a sentence. This approach allows SentiSyn to effectively capture and channel sentiment-related characteristics that are deeply rooted in the syntactic context of the aspect target. By doing so, SentiSyn unlocks a deeper understanding of sentiment dynamics in textual content, enabling a more nuanced and accurate sentiment analysis. Our comprehensive experimental evaluation of SentiSyn showcases its remarkable capabilities. When combined with advanced embedding techniques like GloVe and BERT, SentiSyn demonstrates a superior performance edge over several existing sentiment analysis methods. This performance leap is not just incremental; it represents a significant enhancement in the field of sentiment analysis, underscoring the importance of syntactic context in understanding sentiments. Furthermore, our analysis delves into how SentiSyn effectively leverages these embeddings to gain a more profound and contextually rich insight into sentiment dynamics. The results from our tests indicate that SentiSyn, with its unique approach to integrating syntactic structures and advanced embeddings, sets a new benchmark in aspect-level sentiment analysis, offering both enhanced accuracy and deeper sentiment understanding.

Intelligent ship technology is currently an international research hotspot, and model predictive control is widely used in the path-tracking control of intelligent vehicles. To construct an intelligent ship anti-disturbance path-tracking control method, firstly, an environmental disturbance model was constructed with the actual meteorological data of the target sea area. Secondly, the Fossen ship equation of motion is linearized and discretized as the ship motion model. Thirdly, the expression of the prediction equation is derived from the ship motion model. Fourthly, the cost function is constructed by using the polar diameter and polar angle values of the ship. Fifth, the power function in the cost function is replaced with an exponential function to obtain an improved cost function. Sixthly, according to the Lyapunov theory and the MPC terminal constraint theory, the stability of the improved cost function is verified. Seventh, different test paths are set up, the environmental disturbance model is taken as the external disturbance, the ship motion model, the prediction equation, and the improved cost function are used to design the anti-disturbance path-tracking control algorithm according to the model prediction control idea for simulation experiments. Finally, different MATLAB simulation results show that the improved cost function can resist disturbance of the external wave, current, and wind, and effectively track the target path. Therefore, this study provides a reference for improving the navigation safety of ship path-tracking.

The LED light source is an important light source for indoor visible light communication. It has the characteristics of a large divergence angle and a high transmission rate. Therefore, using LED as the light source for visible light full-duplex communication can not only satisfy the lighting requirements but also transmit information at high speed. To analyze the factors that affect the optical power of the indoor single-light source visible light communication uplink receiving end, an indoor visible light communication model was established, and mathematical calculation formulas were derived based on the model establishment, and the maximum movable range formula of the retroreflective end under specific conditions was derived; The reliability of the formula was verified with the help of Zemax simulation software. Theoretical analysis and experimental results show that increasing the movement range of the retroreflective end can be achieved by increasing the lens diameter, reducing the focal length, and increasing the link distance.

This study aims to evaluate the combined assimilation of AGRI infrared radiance and ground-based MWR (Microwave Radiometer) data for predicting short-duration heavy rainfall. The WRFDA 4.3 framework is utilized to establish the data assimilation interface. The structural characteristics of this joint assimilation approach are analyzed using a typical heavy rainfall event in the Kaifeng region of Central China. The findings indicate the following: (1) The joint assimilation of FY-4A AGRI and ground-based MWR data effectively corrects the initial moisture content in model simulations. Data assimilation significantly improves the simulation of 24-hour accumulated rainfall. Furthermore, the joint assimilation of AGRI radiance and MWR data outperforms assimilating either of them individually; (2) In the heavy rainfall stage, from the low level to the high level, strong upward movement occurs in the center of the rainstorm. The water vapor in the process of this rainstorm mainly comes from the westward air transport in front of the high trough. The water vapor is continuously transported to the heavy rainfall belt through this channel, providing sufficient water vapor for the maintenance of the rainstorm; (3) The combination of the interaction between high and low level vorticity and divergence in the atmosphere and the vertical upward movement, the emergence of low level jet and the generation of unstable energy in the atmospheric environment jointly lead to the occurrence of the rainstorm process; and (4) The terrain-sensitive experiment results show that, the existence of the topography of Taihang Mountain changes the precipitation in Kaifeng area, and reducing the terrain height will lead to a 50%-60% decrease in the overall precipitation of the precipitation center, and the precipitation range will also be greatly reduced. An increase of more than 50% in terrain height will lead to an increase in precipitation center, precipitation range and precipitation intensity, and an increase of 10%-20% in overall precipitation; An increase of more than 75% in the terrain height will cause the rain belt to shift eastward by about 0.5°E, and the precipitation center will shift significantly eastward. When the terrain height increased by more than 100%, the precipitation did not continue to increase, which was basically the same as the control test. This paper provides a valuable basis for further improving the application of FY-4A AGRI radiance and ground-based microwave radiometer in numerical weather models.

The airflow carried by artificial aeration provides oxidant O2 for microbial growth and mineral dissolution in heap bioleaching. To investigate the effect of forced aeration rate on bioleaching of low-grade copper sulfide ores, column bioleaching experiments with six columns were conducted in the aeration range of 0~150 L/h at 30~45 ℃. The results showed that when the aeration rate was higher than 95 L/h, the proportions of heap settlement and fine particles mass were much greater than that without aeration. The final total Fe concentration and bacterial cell numbers in pregnant leach solution increased with the increase of aeration rate.The final concentrations of Cu2 + in the mother liquor under aeration conditions of 60-150 L / h were 1.411, 1.432, 1.498, 1.491 and 1.583 g / L, respectively, which were higher than 1.345 g / L under non-aeration conditions. When the aeration rate was 150 L / h, the final Cu leaching rate was 80.1 %, which was 11.4 % higher than that without aeration ( 68.7 % ). Furthermore, in the early stage of leaching, copper leaching rate with 95 L/h aeration rate remained the highest. 结论Artificial aeration accelerates the bioleaching of low-grade copper sulfide ores by improving porosity structure, temperature range of bacterial activity and microbial catalyzed dissolution of targeted minerals.

Abstract—Online learning platforms provide diverse course resources, but this often result in the issue of information overload. Learners always want to learn courses that are appropriate for their knowledge level and preferences quickly and accurately. Effective course recommendation plays a key role in helping learners select appropriate courses and improving the efficiency of online learning. However, when a user is enrolled in multiple courses, Existing course recommendation methods face the challenge in accurately recommending the target course that is most relevant to the user, because of the noise courses. In this paper, we propose a novel reinforcement learning model named Actor-Critic Hierarchical Reinforcement Learning (ACHRL). The model incorporates the Actor-Critic method to construct the profile reviser. This can remove noise courses and make personalized course recommendation effectively. Furthermore, we propose a policy gradient based on temporal difference error to reduce the variance in the training process, to speed up the convergence of the model, and improves the accuracy of the recommendation. We evaluate the proposed model on two real datasets, and the experimental results show that the proposed model is significantly outperforms the existing recommendation models (improving 3.77% to 13.66% in terms of HR@5).

China is striving to leverage the power of science and technology to green its agriculture while increasing grain productivity. In this context, this study presents the green growth rate of agriculture from the DEA-based Green Total Factor Productivity (GTFP) indicator, together with the growth rate of grain yields, and applies it to the case of Jiangsu, a major grain-producing province with a well-developed economy. It is found that Jiangsu's agriculture has generally performed well in the implementation of the two major national strategies of green development and grain security, especially in the northern Jiangsu, which is a major grain-producing area. In contrast, the phased fluctuations of green growth in agriculture in Southern Jiangsu are more pronounced, with even negative green growth occurring during the green agriculture movement. Much of the volatility in agricultural green growth at the provincial, subregional, municipal level comes from the effects of the movement of the green technology frontier led by best practitioners. Accordingly, the possibility of improving the weak state of the catch-up effect on green growth is explored from the perspective of the Chinese government-led agricultural science and innovation system; it also traces the green agricultural initiatives in the main grain-marketing areas that have failed to deliver the expected green growth, and recommends a review of such policies and refinement of the GTFP Index tool for assessing sustainable green growth.

Delta parallel robot has been widely used in precision parts processing, handling, sorting, and precision assembly, with high efficiency and motion stability being its important performance indexes. Any small line segment corner in trajectory planning causes tangential discontinuous trajectory abrupt change, and the process vibration and shock caused by it seriously affect its high-speed and high-precision performance. In this paper, a trajectory planning method combining Cartesian space and joint space is proposed. Firstly, the vector method and micro-element integration method are used to establish the complete kinematics and dynamics equations of the Delta parallel robot, and the inverse kinematics/dynamics model-solving program is written based on Matlab software. Secondly, the end-effector trajectory of the Delta parallel robot is planned in Cartesian space, and the data points and inverse control points of the end-effector trajectory are obtained by the normalization method. Finally, the data points and control points are mapped to the joint space through the inverse kinematics equation, and the fifth-order B-spline curve is adopted for quadratic trajectory planning, which realizes the high-order continuous smoothing of trajectory planning. The simulation and experiment results show that the trajectory smoothing performance of continuous high-order curvature change can be improved using the proposed method, the tracking error of the end-effector is reduced by 21.12%, and the peak torques change of three joints is reduced by 3.5%, 11.6% and 1.6%, respectively.

Conducting computational stress-strain analysis using finite element methods (FEM) is a common approach when dealing with the complex geometries of atherosclerosis, which is a leading cause of global mortality and complex cardiovascular disease. The considerable expense linked to FEM analysis encourages the substitution of FEM with a considerably faster data-driven machine learning (ML) approach. This study investigated the potential of end-to-end deep learning tools as a more effective substitute for FEM in predicting stress-strain fields within 2D cross sections of arterial wall. We first proposed a U-Net based fully convolutional neural network (CNN) to predict the von Mises stress and strain distribution based on the spatial arrangement of calcification within arterial wall cross-sections. Further, we developed a conditional generative adversarial network (cGAN) to enhance, particularly from the perceptual perspective, the prediction accuracy of stress and strain field maps for arterial walls with various calcification quantities and spatial configurations. On top of U-Net and cGAN, we also proposed their ensemble approaches to further improve the prediction accuracy of field maps. Our dataset, consisting of input and output images, was generated by implementing boundary conditions and extracting stress-strain field maps. The trained U-Net models can accurately predict von Mises stress and strain fields, with structural similarity index scores (SSIM) of 0.854 and 0.830 and mean squared errors of 0.017 and 0.018 for stress and strain, respectively, on a reserved test set. Meanwhile, the cGAN models in a combination of ensemble and transfer learning techniques demonstrate high accuracy in predicting von Mises stress and strain fields, as evidenced by SSIM scores of 0.890 for stress and 0.803 for strain. Additionally, mean squared errors of 0.008 for stress and 0.017 for strain further support the model's performance on a designated test set. Overall, this study developed a surrogate model for finite element analysis, which can accurately and efficiently predict stress-strain fields of arterial walls regardless of complex geometries and boundary conditions.

Ship detection in large-scene offshore synthetic aperture radar (SAR) images is crucial in civil and military fields, such as maritime management and wartime reconnaissance. However, the problems of low detection rates, high false alarm rates, and high missed detection rates of offshore ship targets in large-scene SAR images are due to the occlusion of objects or mutual occlusion among targets, especially for small ship targets. To solve this problem, this study proposes a target detection model (TAC_CSAC_Net) that incorporates a multi-attention mechanism for detecting marine vessels in large-scene SAR images. Experiments were conducted on two public datasets, the SAR-Ship-Dataset and high-resolution SAR image dataset (HRSID), with multi-scene and multi-size, and the results showed that the proposed TAC_CSAC_Net model achieves good performance for both small and occluded target detection. Experiments were conducted on a real large-scene dataset, LS-SSDD, to obtain the detection results of subgraphs of the same scene. Quantitative comparisons were made with classical and recently developed deep learning models, and the experiments demonstrated that the proposed model outperformed other models for large-scene SAR image target detection.

Experimental methodologies for fatigue lifetime prediction are time-intensive and susceptible to environmental variables. While the cohesive zone model is popular for predicting adhesive fatigue lifetime, entropy-based methods have also shown promise. This study aims to provide an understanding of the durability characteristics of CFRP adhesive joints by incorporating an entropy damage model within the context of the finite element method (FEM), examined the effects of different adhesive layer thicknesses on SLS models. As the adhesive layer increased in thickness, DAMAGE VARIABLES initially rose and then declined, peaking at 0.3mm. This finding provides crucial understanding into the stress behavior at the resin-CFRP interface and the resin's fatigue mechanisms.

The Dst index is the geomagnetic storm index used to measure the energy level of geomagnetic storms, and the prediction of this index is of great significance for the geomagnetic storm study and the solar activity. In contrast to traditional numerical modelling techniques, machine learning, which has emerged in decades ago based on rapidly developing computer hardware and software and artificial intelligence methods, has been unprecedentedly developed in geophysics, especially solar-terrestrial space physics. This study chooses two machine learning models, the LSTM (Long-Short Time Memory, LSTM) and EMD-LSTM model (Empirical Mode Decomposition, EMD), to model and predict the Dst index. By building the Dst index data series from 2018-2023, two models were built to fit and predict the data. Firstly, we evaluated the influences of the learning rate and the amount of training data on the prediction accuracy of the LSTM model, and finally, 10-3 was thought as the optimal learning rate; secondly, the two models were used to predict the Dst index in the solar active and quiet periods, respectively, and the RMSE (Root Mean Square Error) of the LSTM model in the active period is 7.34 nT, the CC (correlation coefficient) is 0.96, those of the quiet period are 2.64nT and 0.97; the RMSE and r of EMD-LSTM model are 8.87nT and 0.93 in active time and 3.29nT and 0.95 in the quiet time. Finally, the prediction accuracy of the LSTM model in short time period is slightly better than the EMD-LSTM model. However, there will be a problem of prediction lag, which the EMD-LSTM model can then solve, and can better predict the geomagnetic storm.

According to the development needs of marine seismic station networking, it is necessary to develop a marine seismometer with a networking function to realize quasi-real-time and large-scale long-term observation of undersea seismic signals. This can lay a solid foundation for marine seismic research and research on earth tectonics, activities, and processes. Based on the advantages and disadvantages of the existing observation equipment, this study proposed to develop a new type of the Autonomous Glide Marine Seismometer(AGMS) that can be applied to the global sea area, focusing on the design and study of the main structure of the carrier of the AGMS. The ultimate strength of the ellipsoidal pressure-resistant spherical shell is investigated by using the finite element analysis method. A reasonable finite element analysis model is proposed through comparing the finite element parameter results with the theoretical formulas and relevant specifications. Finally, the design process and strength checking of the pressure-resistant shell of the AGMS are established. These relevant results can also provide a reference for the design of other deep-sea pressure-resistant chambers.

Parental phubbing behavior is a significant factor in predicting adolescent smartphone dependence, but prior research has predominantly focused on a unidirectional perspective from the child's viewpoint, overlooking potential perceptual differences between parents and their children regarding parental phubbing. Therefore, are there differences in the perceptions of parental phubbing between parents and their children? Based on the "Discrepancy-Maladaptive" hypothesis, the presence of perceptual discrepancies in family factors can lead to adverse developmental outcomes in children. Does the parent-child perceptual discrepancy in parental phubbing influence adolescent smartphone dependence? And what role does parent-child relationship play in this context? This study selected 728 families from a middle school in Wuhan, and surveys were administered to both children and parents. The findings reveal: (1) There exist significant parent-child perceptual discrepancies in parental phubbing. (2) Parent-child perceptual discrepancies in parental phubbing significantly positively predict adolescent smartphone dependence and negatively predict parent-child relationships, while parent-child relationships significantly negatively predict adolescent smartphone dependence. (3) The parent-child relationship plays a mediating role between parent-child perceptual differences in parental phubbing behavior and adolescent smartphone dependence.

Background: Gestational diabetes is a common complication during pregnancy that can lead to numerous adverse outcomes. Some studies suggest that probiotics may be used to treat gestational diabetes, however, the results remain controversial. We conducted a systematic review and meta-analysis to evaluate the effect of probiotics on blood glucose and pregnancy outcomes in women with gestational diabetes. Methods: A systematic search of PubMed, Embase, and Cochrane databases was performed (start date to August 22, 2023). Primary outcomes included fasting blood sugar (FBS), fasting serum insulin (FSI), homeostasis model assessment of insulin resistance (HOMA-IR), and quantitative insulin sensitivity check index (QUICKI). Secondary outcomes included pregnancy and neonatal outcomes. Results: 15 articles (n = 1006 women) met the inclusion criteria and were included in the analysis. Compared to a placebo, probiotics can decrease FBS (MD -2.58, 95% CI -4.38 to -0.79, p < 0.01), FSI (MD -2.29, 95% CI -3.40 to -1.18, p < 0.01), HOMA-IR (MD -0.56, 95% CI -0.81 to -0.32, p < 0.01), birthweight (MD -101.20, 95% CI -184.62 to -17.77, p = 0.02), neonatal intensive care unit (NICU) (RR 0.60, 95% CI 0.40 to 0.89, p = 0.01), and hyperbilirubinemia (RR 0.31, 95% CI 0.16 to 0.61, p < 0.01), alongside higher QUICKI (MD 0.01, 95% CI 0.00 to 0.01, p < 0.01). However, no other significant results were obtained. Conclusion: Probiotics may improve blood glucose indicators and reduce neonatal hyperbilirubinemia, NICU admissions, and birth weight in women with GDM.

Revealing the multidimensional value of cultivated land resources, improving calculation methods, and exploring their spatial distribution characteristics and influencing factors are crucial for the enhancement of natural resource accounting system and the protection of cultivated land resources. This study take Guangxi, China as an example and construct a comprehensive multidimensional value evaluation system for cultivated land resources at the county scale. The income capitalization method, substitution market method, and value equivalent correction method were applied to calculate the economic, social, and ecological values of cultivated land resources in 111 counties. Furthermore, spatial autocorrelation analysis was employed to study their distribution characteristics and influencing factors. The results show that: (1) The total value of cultivated land resources in Guangxi reach 19,729.2 billion yuan, and the average cultivated land value is 5.3511 million yuan/hm2, of which the ratio of economic, social and ecological values is about 6:1:2; (2) The value of cultivated land has a certain distribution pattern in the global space, and the average economic and social value show the spatial distribution patterns of "low in the west and high in the east" and "low in the northwest and high in the southeast" respectively."(3) There is a significant spatial clustering effect of all values of cultivated land resources in local space, with "high-high" and "low-low" clustering. (4) Economic development level is significantly negatively correlated with the ecological value of cultivated land, while has a significant positive correlation with social value; (5) Natural conditions, economic development and agricultural development approaches are the key factors affecting the value of cultivated land resources.

Efforts to enhance quality control (QC) practices in chip seal construction have predominantly relied on single surface frictional metrics such as mean profile depth (MPD) or friction number. These metrics assess chip seal quality by targeting issues such as aggregate loss or excessive bleeding, which may yield low friction numbers or texture depths. However, aggregate loss particularly due to snowplow operations doesn't always result in slippery conditions and may lead to uneven surfaces. The correlation between higher MPD or friction number and superior chip seal quality isn't straightforward. This research introduces an innovative machine learning-based approach to enhance chip seal QC. Using a hybrid DBSCAN-Isolation Forest model, anomaly detection is conducted on a dataset comprising 183,794 20-meter MPD measurements from actual chip seal projects across six districts in Indiana. This results in typical 20 m-segment MPD ranges of [0.9, 1.9], [0.6, 2.1], [0.3, 1.3], [1.0, 1.7], [0.6, 1.9], and [1.0, 2.3] for the respective six districts in Indiana. A two-step QC procedure tailored for chip seal evaluation is proposed. The first step calculates outlier percentages across 1-mile segments, with an established limit of 25% outlier segments per wheel track. The second step assesses unqualified rates across projects, setting a threshold of 50% for 1-mile unqualified wheel track segments. While the results are data-specific, this framework offers pavement construction practitioners a foundational QC standard for chip seal projects.

Microwave absorbers with lightweight, good stability and high efficiency have attracted much attention for their applications in many contemporary fields. In this work, the 3D porous (Ni@NO-C)n/NO-C composite absorber was prepared by a wet chemistry method with Ni chains and melamine as precursors, in which NO-C (N,O-doped carbon) encapsulated Ni particles are homogenously dispersed in the 3D porous networks of NO-C in the form of (Ni@NO-C)n chains. The special microstructure of the as-prepared material is proved to be benefit for the improvement of its microwave adsorption performance. The as-synthesized (Ni@NO-C)n/NO-C composite ab-sorber exhibited an effective absorption bandwidth of 4.1 GHz and an extremely large reflection loss of -72.3 dB. The excellent microwave absorbing performances can be ascribed to the coopera-tive consequence of dielectric loss and magnetic loss along with the balance between attenuation capability and impedance match.

Cotton cultivation and sustaining its productivity is challenging in temperate arid regions around the globe. Exploring suitable cotton cultivation areas to improve productivity in such climatic regions is essential. Thus, this study explores the ecologically suitable areas of cotton cultivation using the Maxent model, having 375 distribution points of long-staple cotton and various factors, including 19 climatic factors, 2 terrain factors, and 6 soil factors in Xinjiang. The area under the curve (AUC) of the predicted results was greater than 0.9, indicating that the model's predictions had fairly high accuracy. However, the main environmental factors that affect cotton's growth are the lowest temperature in the coldest month, the hottest month, the precipitation in the driest season, and the monthly average temperature difference. Further, the temperature factors contribute 71%, while the contribution ratio of terrain and soil factors is only 22%. The research shows that the current planting area is consistent with the predicted area in many areas of the study. Still, some areas, such as the Turpan region, northwest of Bayingolin Mongol Autonomous Prefecture, are supposed to be suitable for planting cotton, but it is not planted. The current potential distribution area of long-staple cotton is mainly located in Aksu Prefecture and the northern part of the Kashgar Prefecture region. The climatic prediction shows that the growing area of long-staple cotton may expand to southern Altay, central Aksu, and Bortala Mongol Autonomous Prefecture. This study will be helpful for cotton cultivation suitability areas in Xinjiang and other regions with similar environments.

Fractures are the most common large organ trauma in humans. The initial inflammatory re-sponse promotes bone healing during the initial post-fracture phase, but chronic and persistent inflammation due to infection or other factors does not contribute to the healing process. The precise mechanisms by which immune cells and their cytokines are regulated in bone healing remain unclear. The use of mesenchymal stem cells (MSCs) for cellular therapy of bones injury is a novel clinical treatment approach. Bone progenitor MSCs not only differentiate into bone, but also interact with the immune system to promote the healing process. We review in vitro and in vivo studies on the role of the immune system and bone marrow MSCs in bone healing and their interactions. A deeper understanding of this paradigm may provide clues to potential therapeu-tic targets in the healing process, thereby improving the reliability and safety of clinical applica-tions of MSCs to promote bone healing.

At the nanoscale, metals exhibit special electrochemical and optical properties, which play an important role in nanobiosensing. In particular, the surface plasmon resonance based on precious metal nanoparticles, as a kind of tag free biosensor technology, has brought high sensitivity, high reliability and convenient operation to the sensor detection. By applying an electrochemical excitation signal on the nano plasma device, modulating its surface electron density and realizing electrochemical coupling surface plasmon resonance, it can effectively complete the joint transmission of electrical signals and optical signals, increase the resonance shift of the spectrum, and further improve the sensitivity of the designed biosensor. In addition, smartphone is playing an increasingly important role in portable mobile sensor detection systems. These systems typically connect sensing devices to smartphone to perceive different types of information, from optical signals to electrochemical signals, providing ideas for the portability and low-cost design of these sensing systems. Among them, electrochemiluminescence, as a special electrochemical coupled optical technology, has good application prospects in mobile sensing detection due to its strong anti-interference ability, which is not affected by background light. In this review, the surface plasmon resonance is introduced from nanoparticles, and its response process is analyzed theoretically. Then, the mechanism and sensing application of electrochemistry coupled surface plasmon resonance and electrochemiluminescence are emphatically introduced. Finally, it extends to the related research of electrochemical coupled optical sensing on mobile detection platforms.

Spectrum distribution is a classical licensed spectrum accessing method in mobile communication networks. The licensed idle spectrum resources are authorized and distributed from spectrum owners to mobile users. However, the exponential growth of user capacity brings excessive load pressure on the traditional centralized network architecture. As lack of sufficient supervision and penalty measures, dishonest behaviors of spectrum owners and spectrum users will lead to the unfair status in the distribution process. As a result, the honest participants’ interest will be harmed. As an important supporting infrastructure of Internet of things technology, 6G cannot completely follow the existing spectrum distribution method. Towards 6G network spectrum distribution, an blockchain based licensed spectrum fair distribution method is proposed. A lightweight consensus mechanism named as proof of trust (PoT) is applied to reduce computational power consumption and consensus time overhead. We deploy the method on the Ethereum test chain, theoretical analysis and experimental results demonstrate the fairness, effectiveness and security of the method.

Hyperspectral image and LiDAR image fusion plays a crucial role in remote sensing by capturing spatial relationships and modeling semantic information for accurate classification and recognition. However, existing methods, like Graph Convolutional Networks (GCNs), face challenges in constructing effective graph structures due to variations in local semantic information and limited receptiveness to large-scale contextual structures. To overcome these limitations, we proposed a invariant attribute-driven binary bi-branch classification (IABC) method which is a unified network that combines binary Convolutional Neural Network (CNN) and GCN with invariant attributes. Our approach utilizes a joint detection framework that can simultaneously learn features from small-scale regular regions and large-scale irregular regions, resulting in an enhanced structured representation of HSI and LiDAR images in the spectral-spatial domain. This approach not only improves the accuracy of classification and recognition but also reduces storage requirements and enables real-time decision-making, which is crucial for effectively processing large-scale remote sensing data. Extensive experiments demonstrates the superior performance of our proposed method in hyperspectral image analysis tasks. The combination of CNNs and GCNs allows for accurate modeling of spatial relationships and effective construction of graph structures. Furthermore, the integration of binary quantization enhances computational efficiency, enabling real-time processing of large-scale data. Therefore, our approach presents a promising opportunity for advancing remote sensing applications using deep learning techniques.

This paper focuses on a joint model to analyse longitudinal proportion and survival data. After transforming the longitudinal proportional data by a logit function, we adopt a partially linear mixed-effect model for it, in which nonlinear function of time is fitted via using B-splines technique and a centered Dirichlet Process Mixture Model (CDPMM) is specified for a general distribution of random effects. The survival data is assumed to a Cox proportional hazard model, the sharing random effects joint model is developed for the two types of data. Combining the Gibbs sampler and the Metropolis-Hastings algorithm, we propose a Bayesian Lasso (BLasso) method to simultaneously estimate unknown parameters and select important covariates. Simulation studies are conducted to investigate the finite sample performance of the proposed methods. An example from the MA.5 research experiment is used to illustrate the proposed methodologies.

With the continuous progress of remote sensing image object detection tasks in recent years, researchers in this field have gradually shifted the focus of their research from horizontal object detection to the study of object detection in arbitrary directions. It is worth noting that some properties are different from the horizontal object detection during oriented object detection that researchers have yet to notice much. This article presents the design of a straightforward and efficient arbitrary-oriented detection system, leveraging the inherent properties of the orientation task, including the rotation angle and box aspect ratio. In the detection of low aspect ratio objects, the angle is of little importance to the orientation bounding box, and it is even difficult to define the angle information in extreme categories. Conversely, in the detection of objects with high aspect ratios, the angle information plays a crucial role and can have a decisive impact on the quality of the detection results. By exploiting the aspect ratio of different targets, this letter proposes a ratio-balanced angle loss that allows the model to make a better trade-off between low-aspect ratio objects and high-aspect ratio objects. The rotation angle of each oriented object, which we naturally embed into a two-dimensional Euclidean space for regression, thus avoiding an overly redundant design and preserving the topological properties of the circular space. The performance of the UCAS-AOD, HRSC2016, and DLR-3K datasets show that the proposed model in this paper achieves a leading level in terms of both accuracy and speed. The code is released at https://github.com/minghuicode/Periodic-Pseudo-Domain.

Aiming at the prediction of environmental vibrations induced by elevated high-speed railway, a machine-learning method is developed by combining random forest algorithm and Bayesian optimization, which using the dataset from on-site experiments . When it comes to achieving a rapid and effective prediction of environmental vibration, there is few research on com-parisons and verifications of different algorithms, and neither on parameter tuning and optimi-zation of machine learning algorithms. In this paper, a field experiment is firstly carried out to measure the ground vibrations caused by high-speed trains running on bridge, and then the en-vironmental vibration characteristics are analyzed in view of ground accelerations and weighted vibration levels. Subsequently, three machine-learning algorithms of linear regression, support vector machine and random forest are developed by using experimental database, and their prediction performance are discussed. Finally, two optimization models for the hyperparameter set of random forest algorithm are further compared. It turns out that the integrated random forest algorithm has higher accuracy in predicting environmental vibration than linear regression and support vector machine; the Bayesian optimization has excellent performance and high efficiency in achieving efficient and in-depth optimization of parameters, and can be combined with the RF machine learning algorithm to effectively predict the environmental vibrations induced by the high-speed railway.

Wireless sensor networks are usually applied in hostile areas where nodes are easy to be moni-tored and captured by adversary. Key distribution is an essential primitive to provide most of security mechanism. However, the characteristic of limited resources of sensors restricts the direct use of conventional key distribution schemes. In this paper, a complete security key distribution scheme based on asymmetric cryptography technology is proposed in both static and mobile scenarios. Mutual authentication is guaranteed using challenge-response mechanism. The per-formance evaluation and security analysis show that the proposed scheme with low complexity not only provides better security for wireless sensor networks, but also reduces storage overhead and key exposure risks.

The high level of noise in helicopter cabins considerably compromises the comfort and safety of the pilot and passengers. To verify the feasibility and effectiveness of microperforated panel composite sound absorption structures for noise suppression in helicopter cabins, simulation and experimental studies were conducted on a model of a light helicopter cabin. First, three microperforated composite sound absorption structures for the helicopter cabin wall panel were designed. Then, a finite element model of the main gear/body acoustic vibration coupling was established to obtain the target frequencies of the microperforated composite sound absorption structures; the acoustic effect was verified by simulation. Finally, a model helicopter cabin equipped with the three microperforated composite sound absorption structures was built, and a cabin noise test was performed. The test results showed that the combined microperforated panel acoustic structure and microperforated panel–porous material composite structure realized an overall cabin sound pressure level attenuation of 8–10 dB, on average, in the wide frequency range of 500–2000 Hz, with an amplitude of more than 20 dB. The microperforated panel–acoustic supermaterial composite structure achieved low-frequency sound absorption in the frequency range of 300–450 Hz. The sound absorption effect reached 50%, and it also exhibited good noise reduction effects in the middle- and high-frequency bands.

Based on multi-source remote sensing data, scenario analysis, and model simulation, the Pareto optimal solutions for water supply, water purification (N retention), and carbon storage and sequestration services under different scenarios were sought by adjusting its land use structure. The results showed that. In Scenario 1(S1), the water supply service needs to increase by 86.820 to 11.211 billion cubic metres, the water purification (N retention) service needs to decrease by 11,400 to 11,700 tons, and the carbon storage and sequestration service need to decrease by 2.070 to 2.487 billion tons. In Scenario 2(S2), the water supply service needs to increase by 8.243–10.666 billion cubic metres, the water purification (N retention) service needs to decrease by 11,300–1.10 million tons, and the carbon storage and sequestration service needs to decrease by 2.033 to 2.466 billion tons. In Scenario 3 (S3), the water supply service needs to increase by 7.832–11.437 billion cubic metres, the water purification (N retention) service needs to decrease by 1.16–10,800 tons, and the carbon storage and sequestration service needs to decrease by 19.220 to 2.380 billion tons. After land use optimisation and adjustment, the S3 ecological land structure is complete and consistent with the vision of ecological protection and urban development in the study area, which is the optimal scenario. After optimising the S3 ecosystem service supply pattern, the water supply, water purification (N retention), and carbon storage and sequestration services could connect the western and eastern ecosystem service supply areas, balance the overall ecosystem service supply pattern of the study area and meet the demand for ecosystem services. The results can guide regional land planning and ecosystem service management optimisation.

To deal with the uncertainties in modeling offshore wind turbines, we proposed a parameter inversion method for the pile-soil interaction model based on structural health monitoring results and the numerical model. The proposed parameter inversion method has a numerical model, an objective function selected using both the numerical and identified results, and an inverse optimization using a random search algorithm in the assumed parameter space. The parameter results in the minimum optimization objective function are identified as the in-situ parameter. The proposed method is confirmed to converge after some iterations, whatever the initial parameter values are. However, different initial parameter cases may converge to slightly different optimal parameters, implying the pile results are sensitive to geological parameters. Moreover, a comparison with the original design results shows design redundancy or risks. Though the proposed method has several flaws, it can shed some light on the influence of uncertainties in offshore wind turbines, such as soil parameters in geological surveys.

A self-protective metal/ liquid microcapsule composite plating coating has been prepared in our previous research. The release speed of liquid core material from microcapsules is crucial for the coating surface properties. The aim of this paper is to study the permeability rule of liquid microcapsules within composite coatings. According to permeability experimental data’s linear characteristics, multiple linear regression is firstly used to set up permeability model of liquid microcapsules. The results show that a reliable mathematical model about membrane porosity, viscosity of core material and membrane thickness is established under ambient temperature and moisture. Meanwhile, the predictive capacity and reliability of this model are analyzed carefully.

Change detection with heterogeneous remote sensing images (Hete-CD) plays an important role in practical applications, especially when homogenous remote sensing images are unavailable. However, bitemporal heterogeneous remote sensing images (HRSIs) cannot compare directly to measure change magnitude, and many deep learning methods require large amounts of samples to train the module. Moreover, labeling many samples for land cover change detection with HRSIs is time-consuming and labor-intensive. Therefore, acquiring satisfactory performance of Hete-CD remains a challenge for deep learning networks with very small training samples. In this study, we promote a novel deep-learning framework for Hete-CD to obtain satisfactory performance while the initial samples are very small. We initially design a multiscale network with select kernel-attention module to focus on capturing different change targets with various sizes and shapes. Then, a simple yet effective non-parametric sample-enhanced algorithm based on the Pearson correlation coeffi-cient is promoted to explore potential samples around each initial sample. Finally, the proposed network and sample-enhanced algorithm are fused into one iterative framework to improve the change detection performance with very small samples. Experimental results conducted on four pairs of actual HRSIs indicated that the proposed framework can achieve competitive accuracies with very small samples for initialization when compared with some state-of-the-art methods. For example, the improvement is approximately 3.38% and 1.99% when compared with the selected traditional methods and deep learning methods, respectively.

Discrete distribution estimation is a fundamental statistical tool, which is widely used to perform data analysis tasks in various applications involving sensitive personal information. Due to privacy concerns, individuals may not always provide their raw information, which leads to unpredictable biases in the final results of estimated distribution. Local Differential Privacy (LDP) is an advanced technique for privacy protection of discrete distribution estimation. Currently, typical LDP mechanisms provide same protection for all items in the domain, which imposes unnecessary perturbation on less sensitive items and thus degrades the utility of final results. Although, several recent works try to alleviate this problem, the utility can be further improved. In this paper, we propose a novel notion called Item-Oriented Personalized LDP (IPLDP), which independently perturbs different items with different privacy budgets to achieve personalized privacy protection. Furthermore, to satisfy IPLDP, we propose the Item-Oriented Personalized Randomized Response (IPRR) based on the observation that the sensitivity of data shows an inverse relationship with the population size of respective individuals. Theoretical analysis and experimental results demonstrate that our method can provide fine-grained privacy protection and improve data utility simultaneously.

Forest resources are an important material basis for ecological protection and economic devel-opment, and are responsible for the dual mission of guaranteeing national ecological safety and grain safety. Forest land is an important carrier of forest resources, and forest landowner is a direct component of forest land management. Forest landowners’ willingness to engage in forest man-agement affects whether the important value function of forest resources can be implemented. Are there differences in the willingness and behavior of forest management between ethnic minority foresters and ordinary foresters? How to stimulate the forest management willingness and behavior of forest farmers in ethnic minority areas?These questions will be about the realization of the value of forest resources. Through the analysis of 185 questionnaires in Yunnan Province, this paper clarifies the current situation of forest management of forest farmers in minority areas. Then, using the Sustainable Livelihoods Framework, we select three indicators including the socio-economic at-tributes of individual farmers, the cognition and experience of forest landowners, and policy guidance. And we use the binary logistic regression model to analyze the factors affecting the willingness of forester to participate in forest management. Through the above analysis, we find that: (1) Forest landowners' willingness to engage in forest management in minority regions is relatively high, at 71.98%. (2) Individual farmers’ socioeconomic attributes have the most significant degree of influence on willingness to engage in forest management, while forest landowners' cognitive and related experiences, policy guidance and other related variables influence willingness to engage in forest management at the macro level. (3) Literacy has a significant positive contribution to man-agement intentions, while forest land area, living standard, whether they are compensated by public welfare forest, and whether they participate in the project of returning farmland to forest and grass have a significant negative effect on management intentions. (4) There are significant differences between forest landowners' willingness to engage in forest management and the influencing factors between minority regions and non-minority regions. Finally, we suggest to improve the willingness to engage in forest management and forestry industry development in minority regions through innovative management methods, concentrated and continuous large-scale management, en-couraging capital investment and driving forest landowners to "nearby employment", optimizing the logging quota system and raising the compensation standard for public welfare forests. This study has important practical significance for promoting the realization of forest ecological products value, consolidating the achievement of poverty alleviation in forest areas and realizing rural re-vitalization in China.

Urban spatial perception critically influences human behavior and emotional reactions, emphasizing the necessity of aligning urban spaces with human needs for enhanced urban living. However, functionality-based categorization of urban architecture is prone to biases, stemming from disparities between objective mapping and subjective perception. These biases can result in urban planning and designs that fail to cater adequately to the needs and preferences of city residents, negatively impacting their quality of life and the city's overall functionality. In this study, we apply machine learning to elucidate these biases within urban spatial perception research, utilizing a three-step methodology: objective mapping, subjective perception analysis, and perception deviation assessment. Our findings reveal that machine learning can expose hidden patterns within this research field, bearing substantial implications for urban planning and design. Of particular note, the study revealed significant discrepancies in the distribution centroids between commercial buildings and residential or public buildings. This result illuminates the spatial organization characteristics of urban architectural functions, serving as a valuable reference for urban planning and development. Moreover, it uncovers the advantages and disadvantages of different data sources and techniques in interpreting urban spatial perception, paving the way for a more comprehensive understanding of the subject. These findings underscore the importance of integrating both objective mapping and subjective perspectives in urban architectural functionality classification.

Poor medication adherence among older adults is a widespread problem worldwide. As the population ages, the design of smartphone medication management apps is critical to improving medication adherence among older adults. Taking the design of an elderly medication reminder APP as an example, this study proposes a sustainable design research method that integrates the KANO model, Analytic Hierarchy Process (AHP), Quality Function Deployment (QFD), and PUGH decision matrix. The method collects user demands through in-depth interviews, and applies the KANO model to classify these demands. The hierarchical structure of user needs is established by using AHP, and the priority is sorted according to the weight and importance determined by the judgment matrix. QFD is used to translate user needs into design requirements, and the house of quality matrix identifies key design requirements. Finally, design alternatives are evaluated using Pugh's concept selection method. The results of this study demonstrate that the integration of KANO-AHP-QFD-PUGH can be effective as a sustainable optimal design approach for the user experience of a medication reminder application for the elderly. This integrated method not only facilitates innovative optimization and sustainability of application design methods but also provides valuable theoretical and practical insights for future drug-assisted design for elderly users.

Hydrological connectivity plays a major role in solving water resource and eco-environmental problems. However, this phenomenon has not been afforded the attention it deserves. Detailed analysis of connectivity in river systems could provide considerable insight into structural and functional attributes of riverine landscapes. The current study used graph theory approach and associated connectivity indicators to explore the characteristics and evolution of river systems and hydrological connectivity in a large catchment (Poyang Lake, China). The results revealed that the structure of the river system tended to be complex during 1990-2020, characterized by a dynamic evolution of tributaries in certain northern areas. Both river density and complexity exhibited an increasing trend by up to 15%, with the change rate after 2000 approximately twice as high as that of the preceding period. Overall, human activities across the catchment are more likely to play a key role in leading to significant changes in the quantity, morphometric, and structure characteristics of the river system. Additionally, the functional connectivity analysis indicated that the index of connectivity (IC) in the downstream catchment is stronger than that of the upstream vegetation areas, suggesting a strong contribution to the runoff-sediment transport (r=0.6-0.7). This study highlights the spatial and temporal evolution of both the structural and functional connectivity in the large Poyang Lake catchment. The findings of this work will bene-fit future water resource management and applications by providing a strategy for protecting the surface hydrology and mass transport of large river basins under climate and land-use changes.

The Ocean Color - Simultaneous Marine and Aerosol Retrieval Tool (OC-SMART) is a robust data processing platform that supports a large array of multi-spectral and hyper-spectral sensors. It provides accurate aerosol optical depths and remote sensing reflectances (Rrs estimates) that can be used to generate products such as absorption coefficients due to phytoplankton and detritus/Gelbstoff as well as backscattering coefficients due to particulate matter. The OC-SMART platform yields improved performance in complex environments by utilizing scientific machine learning (SciML) in conjunction with comprehensive radiative transfer computations. This paper expands the capability of OC-SMART by quantifying uncertainties in ocean color retrievals. Bayesian inversion is used to relate measured top of atmosphere radiances and a priori data to estimate posterior probability density functions and associated uncertainties. A framework of the methodology and implementation strategy is presented and uncertainty estimates for Rrs retrievals are provided to demonstrate the approach by applying it to MODIS, OLCI Sentinel-3, and VIIRS sensor data.

In recent years, since flood disasters have brought immeasurable losses to the city, it is urgent to prevent and solve the flood of stagnant water. Considering the shortage of real-time and accuracy of hydrological analysis, Opencv technology is used in this paper to process the obtained data in real time. For improved Yolov5, BoTNet and GAMAttention Transformer are used to improve Yolov5 to enhance its ability of recognition and prediction to better identify surface gathered water. The prediction rate of the improved Yolov5 is 7.1% higher than that of Yolov7 and 1.7% higher than that of Yolov5.After that, contour preprocessing of the image is carried out through the cropping technology of the identification frame to eliminate relatively unstable factors. The principle of binocular distance measurement is used to measure the three-dimensional coordinates of the actual distance, better constrain the contour proportion of the picture, and then the Opencv technology is used to get the outline of the water, and HSV is combined with better color processing pictures for the identification of the water and contour generation, and the area is obtained to correspond to the corresponding parameters of flood to provide important help in flood prevention and storm drainage.

When ground-penetrating radar is used to detect targets within concrete, the location of the targets, the identification of different shapes, properties and less obvious echoes all greatly increase the interpretation time of the staff and can easily cause misjudgment of the echo images. In this paper, the ground-penetrating radar echo images (B-scan) after processing are mean filtered to eliminate the direct waves that interfere greatly with the echoes. The RFB-s structure is added to the YOLOv3-SPP network structure, while the Anchor value is optimized and the EIOU loss function is introduced. For four types of data with different shapes and properties at random target locations, three models, YOLOv3, YOLOv3-SPP and the improved YOLOv3-SPP, are used for classification and identification, and the proposed algorithm models are comprehensively evaluated using model evaluation metrics. The experimental results show that the algorithm models proposed in this paper have good recognition effect in ground-penetrating radar echo image target detection.

Our previous studies showed pure blue (B) spectra from LEDs can promote shade avoidance responses (SARs). However, it is unknown whether SARs vary among different peak wavelengths (λpeak) of B or how they compare with other photomorphologically-important wavebands, such as ultraviolet-A and far-red. To answer these questions, mustard (Brassica juncea, ‘Ruby Streaks’) and arugula (Brassica eruca, ‘Rocket’) seedlings, grown to the cotyledon unfolding stage under the following narrowband spectrum treatments: UVA (λpeak = 385 nm), B1 (λpeak = 404 nm), B2 (λpeak = 440 nm), B3 (λpeak = 455 nm), and FR (λpeak = 730 nm). Both red (R, λpeak = 660 nm) and dark (D) were used as control treatments. The spectrum treatments were provided at 50 μmol m−2 s−1 on a continuous basis. There were no differences among the B treatments except for reduced mustard fresh weight (FWt) in B3. Compared with R, the B treatments promoted hypocotyl elongation, reduced cotyledon size, and increased petiole length in arugula and B1 increased petiole length in mustard. Compared with the B treatments, UVA inhibited hypocotyl and petiole elongation, similar to or greater than R in both species. Compared with the other LED treatments, seedlings grown under FR generally had the lowest hypocotyl and petiole elongation and the smallest cotyledons. Compared to the LED treatments, D substantially promoted hypocotyl elongation and reduced cotyledon size, except compared to FR in arugula. Among the spectrum treatments, the three B treatments had the greatest SAR promotion effects in both species. Despite having the lowest phytochrome activity, FR inhibited SARs normally associated with high FR environments. Legacy parameters used to estimate SAR-promoting effects of spectrum treatments may not be appropriate for characterizing narrowband spectra from LEDs – new approaches must be developed.

The point cloud is a form of three-dimensional data that comprises various detailed features at multiple scales. Due to this characteristic and its irregularity, point cloud analysis based on deep learning is challenging. While previous works utilize the sampling-grouping operation of PointNet++ for feature description and then explore geometry by means of sophisticated feature extractors or deep networks, such operations fail to describe multi-scale features effectively. Additionally, these techniques have led to performance saturation. And it is difficult for standard MLPs to directly "mine" point cloud. To address above problems, we propose the Detail Activation (DA) module, which encodes data based on Fourier transform after sampling and grouping. We activate the channels at different frequency levels from low to high in the DA module to gradually recover finer point cloud details. As training progresses, the proposed Point-MDA can uncover local and global geometries of point cloud progressively. Our experiments show that Point-MDA achieves superior classification accuracy, outperforming PointNet++ by 3.3% and 7.9% in terms of overall accuracy on the ModelNet40 and ScanObjectNN dataset, respectively. Furthermore, it accomplishes this without employing complicated operations, while exploring the full potential of PointNet++.

Sulfate attack is one of the main factors affecting the durability of concrete structures. In recent years, multi-walled carbon nanotubes (MWCNTs) have attracted the attention of scholars for their excellent mechanical properties and durability performance. In this paper, the influence of sulfate attack and dry-wet cycles on the performance of multi-walled carbon nanotube-lithium slag concrete (MWCNTs-LSC) with varied MWCNTs content (0wt%, 0.05wt%, 0.10wt% and 0.15wt%) and varied water-cement ratios (0.35, 0.40 and 0.45) were investigated. Besides, scanning electron microscopy (SEM) and X-ray computed tomography (CT) tests were conducted to analyze the microstructure and pore structure of the concrete. The results show that concrete incorporated with MWCNTs could effectively mitigate sulfate attack The resistance to sulfate attack of concrete is negatively related to the water-cement ratio when the dry-wet cycle is fixed. The MWCNTs-LSC showed the best compressive strength at the water-cement ratio of 0.35 and 0.10 wt% MWCNTs. The SEM test results showed that the MWCNTs both filled the pores and cracks within the specimen and formed bridges between the cracks, enhancing the resistance to sulfate attack. The CT test results also showed that the addition of MWCNTs could reduce the porosity of concrete, refine the pore size and inhibit the generation and development of cracks, thus optimizing the internal structure of concrete and improving its resistance to sulfate attack.

Based on the 2013–2017 Chinese Family Database and China Household Finance Survey, the study examines the impact of farmland transfer on the income structure of agricultural households. We observe a significant rise in the income of transferred-out households, while that of transferred-in households is unchanged. A further empirical decomposition of income shows a significant increase in both the wage and asset generated incomes of transferred-out households. Although the income generated by transferred-in households through agricultural production and management increases significantly, the decrease in wage income is larger. The study’s empirical designs are robustly tested with propensity score matching and instrumental variables. Moreover, we conduct a comparative analysis of the external constraints faced by the two groups to explore the reasons for the divergence of the income effect. The results show that transferred-in households face highly pronounced external constraints in terms of capital, technology, and farmland size, while transferred-out households face relatively fewer impediments to non-agricultural employment. Our empirical results imply that external constraints can limit the social welfare improvements of agricultural land reform, suggesting that other complementary measures would be required for future policy improvements to work better.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

To realize the diagnosis of compound faults in gearboxes at different speeds, an "end-to-end" intelligent diagnosis method based on a deep neural network is proposed, named efficiency channel attention-capsule network (ECA-CN). First, the process uses a deep convolutional neural network to extract fault features from the collected raw vibration signals, then embeds the efficient channel attention module to filter important fault features, then uses the capsule network to vectorize the feature space information, and finally calculates the correlation between different levels of capsules by the dynamic routing algorithm to achieve accurate gearbox compound fault diagnosis. The effectiveness of the proposed ECA-CN fault diagnosis method was verified by the composite fault dataset of the 2009 PHM Challenge gearbox, with an average accuracy of 99.63% and a standard deviation of 0.22%. In the comparison experiments with the traditional fault diagnosis method, the average accuracy of the ECA-CN method was improved by 4.62%, and the standard deviation was reduced by 0.58%. The experimental results show that ECA-CN has a more competitive diagnostic performance.

For W-band long-range mm-wave wireless transmission systems, nonlinearity issues resulting from photoelectric devices, optical fiber, and wireless power amplifiers can be handled by deep learning equalization algorithms. Besides, the PS technique is considered an effective measure to further increase the capacity of the modulation-constraint channel. However, since the proba-bilistic distribution of m-QAM varies with the amplitude, there have been difficulties in learning valuable information from the minority class. This limits the gain of nonlinear equalization. To overcome the imbalanced machine learning problem, we propose a novel two-lane DNN (TLD) equalizer with the random over-sampling (ROS) technique in this paper. The combination of PS at the transmitter and ROS at the receiver improves the overall performance of the W-band wireless transmission system, and our 4.6-km ROF delivery experiment verifies its effectiveness for the W-band mm-wave PS-16QAM system. Based on our proposed equalization scheme, we realize single-channel 10-Gbaud W-band PS-16QAM wireless transmission over 100 m optical fiber link and 4.6-km wireless air-free distance. The results show that compared with the typical TLD without ROS, the TLD-ROS can improve the receiver sensitivity by 1dB. Furthermore, a reduction of 45.6% in complexity is realized, and training samples can be reduced by 15.5%. Considering the actual wireless physical layer with its requirements, there is much to be gained from the joint use of deep learning and balanced data pre-processing techniques.

Protein phosphorylation and ADP-ribosylation (ADPr), as two types of post-translational modifications (PTM), are the process of adding phosphate group and ADP-ribose moieties to proteins, respectively. Although both PTM types can occur on many amino acid types, serine is the most common. Serine phosphorylation (pS), serine ADPr (SADPr), and their in situ crosstalks (pSADPr) play essential roles in biological processes. Although in silico classifiers have been developed for predicting pS and SADPr sites, the classifier for predicting pSADPr sites is unavailable. In this study, we developed classifiers to predict pSADPr sites. Specifically, we collected 3250 human pSADPr, 7520 SADPr, 151,227 pS and 80,096 unmodified serine sites. Based on them, we investigated the characteristics of pSADPr sites and constructed three classifiers to predict pSADPr sites from the pS dataset, the SADPr dataset and the protein sequences separately. We built and evaluated five deep-learning classifiers in ten-fold cross-validation and independent test datasets. Three of them (e.g. Convolutional Neural Network with the One-Hot encoding, dubbed CNNOH) performed better than the rest two. For instance, CNNOH had the AUC values of 0.700, 0.914 and 0.954 for recognizing pSADPr sites from the SADPr, pS and unmodified serine sites.Therefore, it is challenging to distinguish pSADPr sites from SADPr sites compared to the other two. It is consistent with our observation that pSADPr's characteristics are more similar to those of SADPr than the rest. Furthermore, we used the classifiers as base classifiers to develop a few stacking-based ensemble classifiers to improve performance. However, none of the ensemble classifiers showed better performances, suggesting that the base classifiers have good enough performances. Finally, we developed an online tool for extensively predicting human pSADPr sites based on the CNNOH classifier, dubbed EdeepSADPr. It is freely available through http://edeepsadpr.bioinfogo.org/.

Psycho-social factors are key factors to the powerlessness of infant mothers who breastfeed. As the theory of planned behavior (TPB) is widely used to investigate the correlation between psycho-social factors and breastfeeding behavior, this study aims to examine the utility of TPB constructs to predict breastfeeding behavior and understand TPB-based psycho-social factors’ effectiveness on breastfeeding behavior. A narrative review consulting Web of Science, Scopus, Ebsco, PubMed, and PsycInfo in English and Chinese has been conducted, with the inclusion of twenty studies published between January 2000 and May 2022. It is reported that psycho-social factors based on TPB for breastfeeding such as affective attitude, instrumental attitude, subjective norm, perceived behavioral control (including self-efficacy), moral norm, breastfeeding knowledge, and self-identity can effectively explain the breastfeeding behavior. Future research should improve the theoretical model of TPB-based breastfeeding and implement more localized prediction and intervention studies on breastfeeding.

Proton exchange membrane water electrolyzers (PEMWEs) for water electrolysis have received tremendous attention due to their immediate response, high proton conductivity, low ohmic losses and gas crossover rate. However, design high activity, economical and long-term durable electrocatalysts in an acidic environment is still the bottleneck to realize the large-scale commercialization of PEMWEs. Iridium-based materials represent one of the most promising classes of oxygen evolution reaction (OER) catalysts due to their intrinsic stability in acid media over ruthenium-based counterparts. However, only a few innovative approaches have been developed to synthesizing iridium-based catalysts (IBCs) in the past decade, mainly due to achieving high activity may deteriorate the stability of IBCs. Accordingly, various engineering strategies of optimizing IBCs have been proposed to address this issue, including doping engineering, morphology engineering, crystal phase engineering and support engineering. Herein, a critical overview focusing on various synthesis and modulation strategies of IBCs is presented, based on an in-depth understanding of the relationship between electronic structures, charge redistribution and activity as well as stability of the electrocatalysts. In addition, the unprecedented achievements in PEMWEs are summarized. The reaction mechanisms and future perspectives are critically discussed to inspire more rational design of IBCs toward practical applications.

Near-surface humidity (Qa) is a key parameter that modulates oceanic evaporation and influences the global water cycle. Remote sensing observations act as feasible sources for long-term and large-scale Qa monitoring. However, existing satellite Qa retrieval models are subject to apparent uncertainties due to model errors and insufficient training data. Based on in situ observations collected over the China Seas over the last two decades, a deep learning approach named Ensemble Mean of Target deep neural networks (EMTnet) was proposed to improve the satellite Qa retrieval over the China Seas for the first time. The EMTnet model outperforms five representative existing models by nearly eliminating the mean bias and significantly reducing the root-mean-square error in satellite Qa retrieval. According to its target deep neural networks selection process, the EMTnet model can obtain more objective learning results when the observational data are divergent. The EMTnet model was subsequently applied to produce a 30-year monthly gridded Qa data over the China Seas. It indicates that the climbing rate of Qa over the China Seas under the background of global warming are probably underestimated by current products.

Solar assisted hybrid cooling systems are promising for the energy saving of refrigeration systems. In most cases, the solar thermal gain is only able to power the heat-driven process of facilities in part of the working period. Therefore, the reduction of compressor power strongly depends upon the duration of heat-driven processes, which has not been addressed properly. Motivated by such knowledge gap, the thermodynamic understanding of solar assisted hybrid cooling systems is deepened through considering the duration in heat-driven processes. Three absorption-compression integrated cooling cycles were taken as examples. It is found that optimal parameters, e.g., inter-stage pressure and temperature, corresponding to various performance indicators trend to be identical, as the duration of heat-driven processes is taken into account. Furthermore, the optimal parameter for different working conditions was obtained. It is displayed that the dimensionless optimal intermediate temperature of layout with the cascade condensation process varies slightly, e.g., 4%, for different conditions. Moreover, the fall of compressor power in entire working periods is nearly independent upon the intermediate temperature. The paper is favorable for the efficient design and operation of solar assisted hybrid cooling systems.

Metal nanoparticles supporting plasmons are widely used to enhance electromagnetic fields, resulting in strong light-matter interactions at the nanoscale in a diverse range of applications. Recently, it has been shown that when metal nanorods are periodically arranged with proper lattice periods, surface lattice resonances (SLRs) can be excited and near fields can be greatly enhanced over extended volumes. In this work, we report significant near field enhancement over even larger volumes by placing the metal nanorod array within a Fabry-Pérot (F-P) microcavity. Results show that taking advantage of strong coupling between the SLR and the photonic F-P resonances, the electric field intensity of the bonding split mode can be enhanced by up to 1935 times, which is about three times of the enhancement of the SLR, and the greatly enhanced field can extend over most of the F-P microcavity. We further show that the F-P resonances of both odd and even orders can strongly couple to the SLR by varying the nanorods position from the middle of the microcavity. We expect that the proposed plasmonic-photonic coupling system will find promising applications in nanolasers, nonlinear optics and sensing.

Light-addressable potentiometric sensor (LAPS) is an electrochemical sensor based on the field-effect principle of semiconductor. It is able to sense the change of Nernst potential on the sensor surface, and the measuring area can be controlled by the illumination. Due to the unique light-addressable ability of LAPS, the chemical imaging system constructed with LAPS can realize the two-dimensional image distribution detection of chemical/biomass. In this paper, the advantages of LAPS as sensing unit of microelectrochemical analysis system are summarized. Then, the greatest development of LAPS analysis system is explained and discussed. Especially, this paper focused on the research of ion diffusion, enzymatic reaction, microbial metabolism and droplet microfluidics by using LAPS analysis system. Finally, the development trends and prospects of LAPS analysis system are illustrated.

Life Cycle Assessment (LCA) is a widely recognized tool used to evaluate environmental impacts of a product or process, based on the environmental inventory database and bills of material. Data quality is one of the most significant factors affecting the analysis results. However, currently most datasets in inventory databases are generic i.e., they may represent material and energy flow of a process at market average, instead of a specific process used by a manufacturer. As a result, stockholders are unable to track their supply chain to find out the actual environmental impact from each supplier and to compare the environmental performance of alternative options. In this paper, we developed a new framework i.e., blockchain based LCA (BC-LCA), where block-chain technology is adapted to secure and transmit inventory data from upstream suppliers to downstream manufacturers. With BC-LCA, more specific data can be acquired along the supply chain in a real-time manner. Moreover, the availability, accuracy, privacy, and automatic update of inventory data can be improved. A case study is provided based on an industrial supply chain, to demonstrate the utilization of BC-LCA.

Dynamic phase modulation is vital for tunable focusing, beaming, polarization conversion and holography. However, it remains challenging to achieve full 360∘ dynamic phase modulation while maintaining high reflectance or transmittance based on metamaterials or metasurfaces in the terahertz regime. Here we propose a doubly resonant graphene-metal hybrid metasurface to address this challenge. Simulation results show that by varying the graphene Fermi energy, the proposed metasurface with two shifting resonances is capable to provide dynamic phase modulation covering a range of 361∘ while maintaining relatively high reflectance above 20% at 1.05 THz. Based on the phase profile design, dynamically tunable beam steering and focusing are numerically demonstrated. We expect this work will advance the engineering of graphene metasurfaces for the dynamic manipulation of terahertz waves.

The load of power system changes with the development of economy, short-term load forecasting play a very important role in dispatching and management of power system. In this paper, the Ant Lion Optimizer (ALO) is introduced to improve the input weights and hidden-layer Matrix of extreme learning machine (ELM), after the parameters of ELM are optimized by ALO, then input nodes, hidden layer nodes and output nodes are determined, so a load forecasting model based on ALO-ELM combined algorithm is established. The proposed method is illustrated based on the historical load data of a city in China. The results show that the average absolute error of short-term load demand predicted by ALO-ELM model is 1.41, while that predicted by ELM is 4.34, the proposed ALO-ELM algorithm is superior to the ELM and meet the requirements of engineering accuracy, which proves the effectiveness of proposed method.

Epidermal growth factor receptor (EGFR) is a receptor tyrosine kinase that instigates several signaling cascades, including the NF-kB signaling pathway, to induce cell differentiation and proliferation. Overexpression and mutations of EGFR are found in up to 30% of solid tumors and correlate with a poor prognosis. Although it is known that EGFR-mediated NF-kB activation is involved in tumor development, the signaling axis is not well elucidated. Here, we found that PKP2 and the LUBAC complex were required for EGFR-mediated NF-kB activation. Upon EGF stimulation, EGFR recruited PKP2 to the plasma membrane, and PKP2 bridged HOIP, the catalytic E3 ubiquitin ligase in the LUBAC, to the EGFR complex. The recruitment activated the LUBAC complex and the linear ubiquitination of NEMO, leading to IkB phosphorylation and subsequent NF-kB activation. Furthermore, EGF-induced linear ubiquitination was critical for tumor cell proliferation and tumor development. Knockout of HOIP impaired EGF-induced NF-kB activity and reduced cell proliferation. HOIP knockout also abrogated the growth of A431 epidermal xenograft tumors in nude mice by more than 70%. More importantly, the HOIP inhibitor, HOIPIN-8, inhibited EGFR-mediated NF-kB activation and cell proliferation of A431, MCF-7, and MDA-MB-231 cancer cells. Overall, our study reveals a novel linear ubiquitination signaling axis of EGFR, and perturbation of HOIP E3 ubiquitin ligase activity is potential targeted cancer therapy.

Null-flux Electro-dynamic suspension (EDS) system promises to be one of the feasible high-speed maglev systems above 600 km/h. On account of its greater current-carrying capacity, superconducting magnet can provide super-magnetomotive force that is required for null-flux EDS system and cannot be provided by electromagnets and permanent magnets. There is already a relatively mature high-speed maglev technology with low temperature superconducting (LTS) magnets as the core, which works in the liquid helium temperature region (T≤4.2 K). 2-Generation high temperature superconducting (HTS) magnet winded by REBa2Cu3O7−δ (REBCO, RE=rare earth) tapes works above 20 K region and do not need to count on liquid helium which is rare on earth. This paper designed HTS no-insulation closed-loop coils applied for EDS system and energized with persistent current switch. The coils can work at persistent current model and has premier thermal quench self-protection. Besides, a full size double-pancake module was designed and manufactured in this paper, and it was tested in liquid nitrogen. The double-pancake module’s critical current is about 54 A and it is capable of working at persistent current model, whose average decay rate measured in 12 hours is 0.58%/day.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes. There are various types of canals, including calice, axial canals, and other internal canals, with structures that are dynamically altered during different coral growth states due to internal calcium transport. However, few studies have considered the regulation of calcium transport in Acropora. In this study, we investigated the morphological changes of the axial canal in six Acropora muricata samples by high resolution micro-computed tomography, observing the patterns of the axial canal during the processes of new branch formation and truncated branch rebuilding. We visualized the formation of a new branch from a calice and deposition of the iconic hexactin skeletons in the axial canal. Furthermore, the diameter and volume changes of the axial canal in truncated branches during rebuilding processes were calculated, revealing that the volume ratio of calcareous deposits in the axial canal exhibit significant increases within the first three weeks, returning to levels in the initial state in the following week. This work indicates that the axial canal can transport calcium to form hexactin skeletons in a new branch and rebuild the tip of a truncated branch. The calcium transport along canal network regulates various growth processes, including budding, branching, skeleton forming, and self-rebuilding of an Acropora colony. Understanding the changes in canal function under normal and extreme conditions will provide theoretical guidance for restoration and protection of coral reefs.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes, while axial canal is the largest canal amongst the network and distributes at the center of a coral branch. However, previous studies indicated that, in the non-radial symmetry transport system of Acropora, axial canal do not play a major role in the transport of hydroplasm, and the action of axial canal in coral growth is still obscure. In this study, we reconstructed six Acropora muricata samples by high resolution micro-computed tomography to investigate the growth patterns of axial canals during the processes of new branch forming and truncated branch rebuilding. We found that the axial canal of a new branch is transformed from a calice and the polyps in the new branch are budded from the polyp in the axial canal. Meanwhile, the axial canal can transport the calcareous skeletons to rebuild the tip of a truncated branch, which represents as the change in the diameter of axial canal and calcareous deposition/reduction in it. This work indicate the regulation of axial canal in the growth processes including budding, branching, and mineralising of an Acropora colony.

Maize varieties with high amylose proportion are more valuable for starch industry. The SBEⅡb gene encodes one of the starch branching isozymes (SBEⅠ, SBEⅡa, and SBEⅡb). Its recessive mutant amylose-extender (ae/sbe2b) decreases the total activities of SBEs and increases amylose proportion up to 60%. Here, the breeding potential of introduced germplasm line GEMS-0067 was evaluated by genotyping and phenotyping. The deletion of the ninth exon of the SBEⅡb gene, high amylose proportion, and the typical irregular granules suggested that this germplasm line was derived from the same resource of high amylose line AE11. The gelatinization and thermal properties, and degree of polymerization of starch chain showed its advantages used for high amylose breeding. However, the negative correlation between amylose proportion and starch content, as well as ker-nel filling characteristics should be overcome during breeding process.

The morphological transformation of an arched ribbon driven by torsion is a scientific problem that is connected with daily life and requires thorough analysis. An arched ribbon can achieve an instantaneous high speed through energy transformation and then return to the original shape of the structure. In this paper, based on the characteristics of the ribbon structure, the dynamic mathematical model of the arched ribbon driven by torsion is established from the Kirchhoff rod equation. The variations of the Euler angle of each point on the center line of the ribbon with the arc coordinate s and the rotation angle of the supports $\phi$ was examined. The relationship between the internal force distribution of each point in the direction of $\hat{d}_{a}$ and the material, cross-sectional properties, and rotation angle of the supports was obtained. We used ABAQUS, a nonlinear finite element analysis tool, to simulate the morphological transformations of the ribbons, verified our theory with simulation results, and reproduced the experimental results of Sano. Furthermore, we redefined the concept of the ``critical flipping point'' of Sano. In this paper, the dimensional analysis method was used to fit the simulation data. The following relationship between the critical width $ w ^{*} $, thickness h, and the radius R of the ribbon with different cross sections was obtained: $w^{*}=A\cdot R\left(h/R\right)^{0.6}$, where A is 3.19 for rectangular cross sections and 3.06 for elliptical cross sections. By analyzing the simulation data, we determined the variation behavior of the out-of-plane deflection of the center point of the ribbon with the radius R, width w, and thickness h. Our research has guiding significance for understanding and designing arched ribbons driven by torsion, and the results can be applied to problems of different scales.

Sea surface partial pressure of CO2 (pCO2) is a critical parameter in the quantification of air-sea CO2 flux, which plays an important role in calculating the global carbon budget and ocean acidification. In this study, we use chlorophyll-a concentration (Chla), sea surface temperature (SST), absorption due to dissolved and particulate detrital matter (Adg), diffuse attenuation coefficient of downwelling irradiance at 490nm (Kd) and mixed layer depth (MLD) as input data for retrieving the sea surface pCO2 in the North Atlantic based on a remote sensing empirical approach with the Categorical Boosting (CatBoost) algorithm. The results show that the root mean square error (RMSE) is 8.25μatm, the mean bias error (MAE) is 4.92μatm and the coefficient of determination (R2) can reach 0.946 in the validation set, which mean that the CatBoost model makes an improvement compared to other models in the published studies. In the further analysis of the spatial and temporal distribution of the sea surface pCO2 in the North Atlantic, it can be found that the North Atlantic sea surface pCO2 has a clear trend with latitude variations and have strong seasonal changes. Furthermore, the sea surface pCO2 in this area is mainly affected by sea temperature and salinity, and influenced by biological activities in some sub-regions.

Why are pieces of spaghetti generally broken into three to ten segments instead of two as one thinks? How can one obtain the desired number of fracture segments? For these problems, in this paper a strand of spaghetti is considered an elastic rod, and the finite-element software ABAQUS is used to simulate the detailed fracture dynamics of the elastic rod. By changing the size (length and diameter) of the rod, the relevant data on the fracture limit curvature and the number of fractured segments of the elastic rod are obtained. The ABAQUS simulation results confirm the scientific judgment of B. Audoly and S. Neukirch (Fragmentation of rods by cascading cracks: Why spaghetti does not break in half. Phys Rev Lett 95: 095505). Using dimensional analysis to fit the finite-element data, two relations of the elastic rod fracture dynamics are obtained: (1) the relationship between the fracture limit curvature and the diameter, and (2) the relationship between the number of fracture segments and the diameter-length ratio. Results reveal that when the length is constant, the larger the diameter (the smaller the diameter-length ratio D/L), the smaller the limit curvature; and the larger the diameter-length ratio D/L, the fewer the number of fractured segments. The relevant formulations can be used to obtain the desired number of broken segments of spaghetti by changing the diameter-to-length ratio.

Why do stretched rubber bands not hit the hand after ejection? What is the mechanism behind the rubber band ejection dynamics? These questions represent a fascinating scientific problem. Because the size of a rubber band in the circumferential direction is much larger than that in the other two directions of its cross-section, we regard the rubber band as a slender beam and establish a mathematical model of the dynamics of the rubber band stretching and ejection. Furthermore, we obtain the dependence of the dynamic curvature of the rubber band on the arc length and time. We used the finite element software ABAQUS to simulate the dynamic process of a rubber band stretching and ejection. The simulation results and dimensional analysis were performed to examine the effect of the bending elastic rebound velocity. The mathematical model and simulation results revealed that the relationship between the curvature and time at the end of the rubber band ($s =0$) was as follows: $\kappa\sim t^{-{1}/{2}}$. This research has guiding significance for the design of rubber bands as elastic energy storage devices.

An increasing number of studies have proposed that corporate social responsibility (CSR) performance depends on how companies apply their resources and capabilities to implement CSR. A firm’s ability to integrate, build, and reconfigure internal and external competencies to respond to environmental changes is its dynamic capability. Implementation of CSR at the strategic level will contribute to a firm’s sustainability. However, the research on strategic CSR is incipient. This study explores possible mechanisms to investigate how dynamic capability influences the performance of strategic CSR in China. By analyzing 134 Chinese listed companies in the period 2017–2019, in this study, we found that firms with a high level of dynamic capability were less likely to adopt strategic CSR practices, and had a low strategic CSR adoption performance. The results confirmed the loss aversion channel, indicating that firms with a high dynamic capability level were loss averse and that managers had a decreasing sensibility in decision-making and allocated fewer company resources in CSR projects. These results can help companies to better understand the dynamic capability and how dynamic capability contributes to the adoption of strategic CSR and performance over time. The policy implications of the study are also discussed.

It has been recognized for some time that even for perfect conductors, the interaction Casimir entropy, due to quantum/thermal fluctuations, can be negative. This result was not considered problematic because it was thought that the self-entropies of the bodies would cancel this negative interaction entropy, yielding a total entropy that was positive. In fact, this cancellation seems not to occur. The positive self entropy of a perfectly conducting sphere does indeed just cancel the negative interaction entropy of a system consisting of a perfectly conducting sphere and plate, but a model with weaker coupling in general possesses a regime where negative self-entropy appears. The physical meaning of this surprising result remains obscure. In this paper we re-examine these issues, using improved physical and mathematical techniques, partly based on the Abel-Plana formula, and present numerical results for arbitrary temperatures and couplings, which exhibit the same remarkable features.

CNN-based methods have dominated the field of aerial scene classification for the past few years. While achieving remarkable success, CNN-based methods suffer from excessive parameters and notoriously rely on large amounts of training data. In this work, we introduce few-shot learning to the aerial scene classification problem. Few-shot learning aims to learn a model on base-set that can quickly adapt to unseen categories in novel-set, using only a few labeled samples. To this end, we proposed a meta-learning method for few-shot classification of aerial scene images. First, we train a feature extractor on all base categories to learn a representation of inputs. Then in the meta-training stage, the classifier is optimized in the metric space by cosine distance with a learnable scale parameter. At last, in the meta-testing stage, the query sample in the unseen category is predicted by the adapted classifier given a few support samples. We conduct extensive experiments on two challenging datasets: NWPU-RESISC45 and RSD46-WHU. The experimental results show that our method yields state-of-the-art performance. Furthermore, several ablation experiments are conducted to investigate the effects of dataset scale, the impact of different metrics and the number of support shots; the experiment results confirm that our model is specifically effective in few-shot settings.

Poly-ether-ether ketone (PEEK) is a great potential thermoplastic in industry and medical treatment and health. In this work, the PEEK/GO and PEEK/MoS2 composites were prepared by a novel hot isostatic pressing method. The addition of GO alters the tribological behaviours mechanism, fatigue wear mechanism is predominant to PEEK/GO composites. However, the combination of abrasive and adhesive wear mechanisms is observed for PEEK/MoS2 composites and PEEK. The reason is the hardness and tensile strength of composites are increased with the appropriate addition of GO. The response time to stable friction state of PEEK/GO and PEEK/MoS2 composites reduces in compared with PEEK, which conduce to shorten running-in time, reduce energy consumption and improve the tribological performances of composites. The addition of GO and MoS2 can effectively decrease the friction coefficient and wear rate, and the optimal content of GO and MoS2 was 0.7 wt.% and 15 wt.%, respectively. The results indicate that PEEK/GO and PEEK/MoS2 are impressive composites that possess super tribological properties.

Long-read single-molecule sequencing has revolutionized de novo genome assembly and enabled the automated reconstruction of reference-quality genomes. It also has been widely used to study structural variants, phase haplotypes and more. Here, we introduce the assembler— SMARTdenovo, which is an SMS assembler that follows the overlap-layout-consensus (OLC) paradigm. SMARTdenovo (RRID: SCR_017622) was designed to be a fast assembler that did not require highly accurate raw reads for error correction, unlike other, contemporaneous SMS assemblers. It has performed well for evaluating congeneric assemblers and has been successful for a variety of assembly projects. It is compatible with Canu for assembling high-quality genomes, and several of the assembly strategies in this program have been incorporated into subsequent popular assemblers. The assembler has been in use since 2015, and here we provide information on the development of SMARTdenovo and how to implement its algorithms into current projects.

The corrected mechanism model of battery voltammetric function is helpful to guide the development and application of battery. There are two scientific issues that need to be answered: First, how many mechanisms do batteries have; Second, how to establish the mechanism model separately under the overlapping of these mechanisms. Volt-ampere characteristics of both linear state and nonlinear state exist; the monotonic decreasing of volt-ampere characteristics indicates that the battery have only three kinds of mechanisms. Without changing the basic form of the function and under the principle of the mechanism function’s working region considered, we propose a mechanism function which satisfies the monotonic decreasing characteristic of the voltammetric curve of battery, via the derivative law of each mechanism function in the voltammetric function of battery. By using the voltammetric data, the obtained cell mechanism function can accurately predict the potential (current or voltage) when the independent variable of the cell is zero, and provide the theoretical basis for the internal working mechanism of the cell, which can guide the practice.

Managing epidemics need to unite each individual of the nations. Lockdown is an essential strategy to fatal and threatening epidemic. All of the citizens should realize that each of people has a responsibility to support the public health crisis. How to organize individual to fight against the epidemic plaque depends each of them. This essay discussed the COVID-19 pandemic relevant self-governance of community from a historical perspective in China. Self-governance of neighborhood committee and community residential office in urban and rural helped to control the COVID-19 pandemic in the communities in China. Co-operation and collective responsibility of citizens and community support is a critical condition to prevent epidemic. The community self-governance can track back Qin Dynasty in China history. It established baojia system to maintain social control for thousand years. Now, the community-based system, baojia system is becoming more autonomous for local citizenship and socialized governance in China. We reviewed a historical pneumonia plaque in North China in 1911. Chinese doctor, Wu Lien-teh (伍連德) confronted the epidemic crisis with many measures such as lockdown, quarantine, the wearing of mask, setup mobile hospitals, travel restriction, the cremation of victims, and border control. Dr. Wu made effort to establish the modern public health service in China. We think that the combination of culture background of China community with modern public healthcare system determinedly played important role to control the COVID-19 pandemic.

Recently, the outbreak of coronavirus disease 2019 (COVID-19) is threatening human health globally. There is a dire need to find potential therapeutic agents. Angiotensin converting enzyme 2 (ACE2), as an entry receptor of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), is considered as potential therapeutic target in COVID-19 pandemic. Here, our bioinformatics analysis revealed that the biological function of ACE2 was correlated with regulation of blood pressure and mediation of SARS-CoV-2 entry into host cells. Ten ACE2 cooperative proteins were identified by using STRING with a high score. ACE2 expressed highly in the small intestine, testis, and kidney. The level of ACE2 expression in tumor tissues varies in different types of cancers compared with that in normal tissues. It was worth noting that the expression level of ACE2 in the tumor has no effect on patient survival. MiRNA hsa-miR-942-5p, and three transcription factors (TFs) including Signal transducer and activator of transcription 4 (STAT4), Estrogen related receptor α (ESRRA), and Signal transducer and activator of transcription 3 (STAT3) were selected as novel ACE2 regulators. Moreover, nine potential therapeutic drugs were predicted by two online databases. Thus, our research may expand the overall view of ACE2 in COVID-19 treatment.

Exploiting the linguistic knowledge of the source language for neural machine translation (NMT) has recently achieved impressive performance on many large-scale language pairs. However, since the Turkish→English machine translation task is low-resource and the source-side Turkish is morphologically-rich, there are limited resources of bilingual corpora and linguistic information available to further improve the NMT performance. Focusing on the above issues, we propose a multi-source NMT approach that models the word feature in parallel to external linguistic features by using two separate encoders to explicitly incorporate linguistic knowledge into the NMT model. We extend the word embedding layer of the knowledge-based encoder to accommodate for each word’s linguistic annotations in the context. Moreover, we share all parameters across encoders to enhance the representation ability of the NMT model on the source language. Experimental results show that our proposed approach achieves substantial improvements of up to 2.4 and 1.1 BLEU scores in Turkish→English and English→Turkish machine translation tasks, respectively, which points to a promising way to utilize the source-side linguistic knowledge for the low-resource NMT.

Background: The Micro Hand S robot is the first domestically produced surgical robot that has entered clinical use in China, and this is the first report of its application in colon cancer. Objective: This study aimed to validate the safety and efficacy of the domestically produced Chinese minimally invasive Micro Hand S surgical robot system in complex surgery, such as robotic complete mesocolic excision (R-CME). Methods: From March 2018 to December 2018, 30 patients with right hemicolon cancer underwent R-CME with the Micro Hand S robot system. The operative findings, morbidities, oncological findings and unique characteristics were summarizedwere analyzed. Result: 12 patients with right hemicolon cancer and 18 patients with sigmoid colon cancer underwent RCME with the Micro Hand S robot system. During the study period, the median operative duration was 209 (range, 180-255) min, and the median estimated blood loss volume was 35 (range, 25-75) ml. The median number of lymph nodes harvested was 42 (21-77), and the median postoperative hospital stay was 5 (range, 4-7) days. According to the Clavien-Dindo classification, there were no severe complications except for 7 cases of grade I complications and 5 cases of grade II complications. The conversion rate for all operations was 0%. There were no cases of 30-day readmission or 30-day mortality. Conclusion: Clinical application of domestically produced Chinese minimally invasive surgical robot system “Micro Hand S ” in selected colon cancer patients is technically feasible and safe.

Background: The Micro Hand S robot is the first domestically produced surgical robot that has entered clinical use in China, and this is the first report of its application in colon cancer.Objective: This study aimed to validate the safety and efficacy of the domestically produced Chinese minimally invasive Micro Hand S surgical robot system in complex surgery, such as robotic complete mesocolic excision (R-CME).Methods: From March 2018 to December 2018, 30 patients with right hemicolon cancer underwent R-CME with the Micro Hand S robot system. The operative findings, morbidities, oncological findings and unique characteristics were summarizedwere analyzed.Result: 12 patients with right hemicolon cancer and 18 patients with sigmoid colon cancer underwent RCME with the Micro Hand S robot system. During the study period, the median operative duration was 209 (range, 180-255) min, and the median estimated blood loss volume was 35 (range, 25-75) ml. The median number of lymph nodes harvested was 42 (21-77), and the median postoperative hospital stay was 5 (range, 4-7) days. According to the Clavien-Dindo classification, there were no severe complications except for 7 cases of grade I complications and 5 cases of grade II complications. The conversion rate for all operations was 0%. There were no cases of 30-day readmission or 30-day mortality. Conclusion: Clinical application of domestically produced Chinese minimally invasive surgical robot system “Micro Hand S ” in selected colon cancer patients is technically feasible and safe.

Less aligned emphasis has been given to the COVID-19 infodemic coordinating with the COVID-19 outbreak. Global profusion of tangled monikers and hashtags has found their ways in daily communication and contributed to backlash against Chinese. Official naming efforts against infodemic should be meet with a fair share of identification. Based on brief critical reviews on previous multifarious naming practices, we punctuate heuristic introspection in scientific conventions and sociocultural paradigms. Infodemiological analysis promises to articulate that people around the globe are divided in their favor stigmatized monikers in the public and scientific communities because of perceptual bias. There is no positive correlation between the degree of infection in their territories and collective perceptual bias to COVID-19. The official portfolio “COVID-19” and “SARS-CoV-2” has not become de facto standard usages, but full-fledged official names are excepted to duly contribute to the resilience of negative perceptual bias and collective behavioral propensities.

Neuronal lesion or injury is a traditional approach to investigate neural circuit. Is any new neural pathway or new neurodegeneration related central nerve system injury? Spinal disc herniation can cause the spinal cord injury. However, the histological examination is still lack. It happened that a case of spinal disc herniation of a 10-year old dog was examined with NADPH diaphorase (N-d) histology. We did not find the N-d neurodegenerative aberrant in the tissue of the mid-rostral lumber segment besides the metamorphoses by the compression of the disc herniation. However, the severe neuropathological changes majorly occurred in the lumbosacral spinal cord. We found more diverse neurodegenerative alterations: the aging-related N-d body (ANB), megaloneurite and N-d homogeneous formazan globule in the lumbosacral spinal cord. We also found that a new circuit pathway (intermedial collateral pathway) showed by a megaloneurite between the lateral collateral pathway and the medial collateral pathway. The enormous notch caused by spinal disc herniation located at the mid-rostral lumber segments. The aging-related neurodegeneration occurred the specific lumbosacral segments. The homogeneous formazan globule was round or oval homogeneous N-d positivity which distributed in the gray matter and dorsal column. In the medulla oblongata, ANBs were revealed in the gracile nucleus, nucleus reticularis lateralis (ventrolateral spinal trigeminal nucleus) and middle of the spinal trigeminal nucleus.

Ethnopharmacological relevance: Novel coronavirus disease (COVID-19) outbroke in Wuhan has imposed a huge influence onto the society in term of the public heath and economy. However, so far, no effective drugs or vaccines have been developed. Whereas, the Traditional Chinese Medicine (TCM) has been considered as a promising supplementary treatment for the disease owing to its clinically proven performance on many diseases even like severe acute respiratory syndrome (SARS). Meanwhile, many side-effect (SE) reports suggest the SE of the TCM prescriptions cannot be ignored in curing the COVID-19, especially because COVID-19 always simultaneously leads to dramatic degradation of the patients’ physical condition. How to evaluate the TCM regarding to their latent SE is a urgent challenge. Aim of the study: In this study, we use an ontology-based side-effect prediction framework (OSPF) developed in our previous work and Artificial Neural Network (ANN)-based deep learning to evaluate the TCM prescriptions that are officially recommended in China for novel coronavirus (COVID-19). Materials and methods: Firstly, we adopted the OSPF developed in our previous work, where an ontology-based model separate all the ingredients in a TCM prescription into two categories: hot and cold. Then, we established a database by converting each TCM prescription into a vector containing the ingredient dosage and the according hot/cold attribution as well as the safe/unsafe label. And, we trained the ANN model using this database, after which a safety indicator (SI), as the complementary percentage of side-effect (SE) possibility, is then given for each TCM prescription. According to the proposed SI from high to low, we re-organize the recommended prescription list. Secondly, by using this method, we also evaluate the safety indicators of some other famous TCM prescriptions that are not in the recommended list but are used traditionally to cure flu-like diseases for extending the potential treatments. Results: Based on the SI generated in the ANN model, FTS, PMSP, and SF are the safest ones in recommended list, which all own a more-than-0.8 SI. Whereas, JHQG, LHQW, SFJD, XBJ, and SHL are the prescriptions that are most likely unsafe, where the indicators are all below 0.2. In the extra list, the indicators of XC, XQRS, CC, and CHBX are all above 0.8, and at the meantime, XZXS, SJ, QW, and KBD’s indicators are all below 0.2. Conclusions: In total, there are seven TCM prescriptions which own the indicators more than 0.8, suggesting these prescriptions should be considered firstly in curing COVID-19, if suitable. We believe this work will provide a reasonable suggestion for the society to choose proper TCM as the supplementary treatment for COVID-19. Besides, this work also introduces a pilot and enlightening method for creating a more reasonable recommendation list of TCM to other diseases.

There always exist steel cuttings, holes and cracks at the interfaces in the explosive composite plate. Multi-pass friction stir processing (M-FSP) is proposed in this research to optimize the interface microstructure and the interface connection for 1060Al/Q235 explosive composite plate. Results show that the microstructures of 1060Al after M-FSP are fine and uniform owing to the strong stirring effect and recrystallization. Micro-defects formed by the explosive welding can be repaired by the M-FSP. However, M-FSP can also form tunnel defects in the aluminum, especially when the passes are one and two. The melting block and the melting lump in the composite plates are easy to become source of crack. The shear strengths and the bending properties for the 1060Al/Q235 explosive composite plate after M-FSP are the best when the passes are three, with the tool rotation speed of 1200rpm and the forward speed of 60mm/min. The optimized interfaces for the explosive composite plate after M-FSP are mainly by the metallurgical bondings, with a certain thickness and are discontinuous. Therefore, the crack extension stress is the largest and the mechanical properties are the best.

Adsorption is an effective strategy for the removal of pollutants from the wastewater. Herein, a 2-hydroxyterephthalic acid (HTC) modified hypercrosslinked polymer (HTC-HCP) is successfully synthesized via Friedel-Crafts reactions, and used as an adsorbent for the different types of pollutants including organic contaminants and heavy metal ions from wastewater. Excellent adsorption capacities are observed for amines (aniline, p-methylaniline (p-MA), p-chloroaniline (p-CA), and p-aminobenzoic acid (p-ABA)), phenols (phenol, p-chlorophenol (4-CP) Bisphenol A (BPA), 1-Naphthol (1-NP)), dyes (rhodamine B (RhB) and methyl orange (MO)), and metal ions (Pb2+, Hg2+, and Cd2+). The resulting polymers exhibited excellent adsorption performance towards these pollutants. Especially, the removal rate of aniline is above 95% in the concentration of 2.5 mg/L in 40 min at 25 °C. The interaction mechanism has been investigated, and confirmed by FTIR and the theoretical calculation results. It is due to surface complexation and chemisorption between adsorbent and adsorbate. The polymer exhibits good performance such as high adsorption capacity, high separation efficiency, biodegradable properties, and easy regeneration, suggesting that its potential technological applications for the removal of organic compounds and heavy metal ions from actual industrial effluent.

An increasingly large quantity of primary mineral resource is being converted into manufactured products and destined for solid waste disposal. This material can be reclassified as “anthropogenic mineral reserves” and be a potential source of metals for a range of manufacturing uses. China is implementing a range of policy interventions which can lead to such a classification that will raise the profile of recycling programs as a means of metal supply. China is not only a major producer of consumer products and importer of secondary metals, but also has a major urban infrastructure footprint. Here we consider three product groups, 30 products, and imports, and map the recycling potential of anthropogenic mineral and 23 types of the capsulated materials by targeting their evolution from 2010 to 2050. Total weight of anthropogenic mineral on average in China reached 39 Mt in 2010, but it will double in 2022 and quadruple in 2045. Stocks of precious metals and rare earths will increase faster than most base materials. The total economic potential in yearly-generated anthropogenic mineral is anticipated to grow markedly from 100 billion US$ in 2020 to 400 billion US$ in 2050. Anthropogenic mineral of around 20 materials will be able to meet projected consumption of three product groups by 2050, due to high availability of recycled content and gradual saturation of consumption. Durability of material usage and the concomitant stock of the anthropogenic mineral remain major challenges in determining the viability of this supply in the second half of the coming century.

The landscape image is the bridge of communication between people and forests, and the cut point of the supply-side reform of forest tourism products. The research collected 140 copies in total of forest landscape image drawings from non-art-major graduate students by randomly sampling during April and May, 2018, and constructed the landscape image conceptual model of forest by utilizing the landscape image sketching technique. The results showed that (1) In regard to linguistic knowledge, the natural landscape elements for instance, herbaceous plants, terrains, creatures, water and sky, and the broad-leaf forest objectively reflected not only the real forest landscape and the local native vegetation, but the variation of forest species with little attention. (2) On the perspective of spatial view, the sideways view indicated that graduate students preferred to watch forests at a moderate distance externally and few looked at forests internally. (3) In the view of self-orientation, the objective landscape indicated that graduate students preferred to demonstrate forest landscapes, they did not realize to interact with the environment. (4) On the aspect of social meaning, the scenic view and forest structure stated that graduate students preferred rural forest landscapes, not significantly for other special interests for forest. In conclusions, (1) the forest is thought to be a feature of people's life world and of rural scenes around homes, not an objective perception of the forest. (2) The forest is regarded as an important habitat for animals and a limited resource for people's life, production and recreation needs, into which people will go only to meet such needs. (3) The natural values of forests, like the ecology and aesthetics, etc. get more attention, while the social values of forests, like the life, production and culture receives rather low attention.

In the study, a new correction method was applied to reduce error during detection on mixed pesticide residue in apples by using Raman spectra. Combined with self-built pesticide residues detection system by Raman spectroscopy and the application of surface enhancement technology, rapid real-time qualitative and quantitative analysis of deltamethrin and acetamiprid residues in apples can be applied effectively. In quantitative analysis, compared with the intensity value of characteristic peaks of single pesticide with same concentration, the intensity value of characteristic peaks of the two pesticides decreased after mixing the pesticides, which interferes the results severely. By comparing the difference in the intensity of characteristic peaks of single and mixed pesticides, a correction method is proposed to eliminate the influence of pesticides mixture. Characteristic peak intensity values of gradient concentration pesticide from 10-1 g•kg-1 to 10-6 g•kg-1 and Lagrangian interpolation are applied in the correction method. And a smooth surface is applied to describe the correction ratio of characteristic peak intensity. Through detecting the characteristic peak intensity values of the mixed pesticide, correction ratio will be obtained. Then real values of the peak intensity of pesticides and the content of each component of the mixed pesticide will be acquired by the correction method. Correlation coefficient of model validation exceeds 0.88 generally and Root Mean Square Error also decreases obviously after correction, which proved the reliability of the method.

The vibration feature of weak gear fault is often covered in strong background noise, which makes it necessary to establish weak feature enhancement methods. Among the enhancement methods, stochastic resonance (SR) has the unique advantage of transferring noise energy to weak signals and has a great application prospection in weak signal extraction. But the traditional SR potential model cannot form a richer potential structure and may lead to system instability when the noise is too great. To overcome these shortcomings, the article presents a periodic potential underdamping stochastic resonance (PPUSR) method after investigating the potential function and system signal-to-noise ratio (SNR). In addition, system parameters are further optimized by using ant colony algorithm. Through simulation and gear experiments, the effectiveness of the proposed method was verified. We concluded that compared with the traditional underdamped stochastic resonance (TUSR) method, the PPUSR method had a higher recognition degree and better frequency response capability.

The Station logo is a way for a TV station to claim copyright, which can realize the analysis and understanding of the video by the identification of the station logo, so as to ensure that the broadcasted TV signal will not be illegally interfered. In this paper, we design a station logo detection method based on Convolutional Neural Network by the characteristics of the station, such as small scale-to-height ratio change and relatively fixed position. Firstly, in order to realize the preprocessing and feature extraction of the station data, the video samples are collected, filtered, framed, labeled and processed. Then, the training sample data and the test sample data are divided proportionally to train the station detection model. Finally, the sample is tested to evaluate the effect of the training model in practice. The simulation experiments prove its validity.

Based on previous research results, we propose a new preprocessing HSS iteration method (PHSS) for the generalized Lyapunov equation. At the same time, the corresponding inexact PHSS algorithm (IPHSS) is given from the angle of application. All the new methods presented in this paper have given the corresponding convergence proof. The numerical experiments are carried out to compare the new method with the existing methods, and the improvement effect is obvious. The feasibility and effectiveness of the proposed method are proved from two aspects of theory and calculation.

As the traditional sand fixation measures have many limitations, new sand fixing technologies and methods are urgently needed to be developed. This study demonstrated a new sand fixation method using palm mat geotextile to fix the sand dunes and plant grass. We experimented the physical property of the palm mat geotextile in the laboratory, and observed the vegetation growth in the Hobq Desert. The results showed that (1) The palm mat geotextile is more lighter and tougher than the common straw mat geotextile, the average weight, thickness and tensile strength of palm mat geotextile were 2023 g/m², 20.14 mm, and 842–860 N/m, after a year of field observation, the tensile strength decreased by only 2%. (2) The palm mat geotextile had excellent water retention capacity and scouring resistance, the maximum water content reached 227%, and the substrate lost 2.9% after the simulation of heavy rainfall for 3 hours with rainfall intensity of 30 mm/h in laboratory. (3) The palm mat geotextile significantly decreased the soil temperature and increase the humidity in summer, the observed results shown that the palm mat geotextile had the greatest influence on 5cm depth of the soil temperature and 10cm depth of soil humidity. (4) The field experiment results showed that the vegetation coverage and the biomass of the palm mat geotextile with 2 m × 2 m were 35% and 11.21 g (3.9 times and 4.1 times than that of control group, 1.7 times and 1.8 times than that of high-banded salix psammophila sand-barriers group which is widely used in the Hobq Desert).

Using a three-dimensional, hydrostatic, primitive-equation ocean model, this study investigates the dynamics of lateral circulation in a partially stratified tidal inlet, the Barataria Pass in the Gulf of Mexico, over a 25.6-hour diurnal tidal cycle. Model performance is assessed against observational data. During flood tide, the lateral circulation exhibits the characteristics similar to that induced by differential advection, i.e., lateral flow consists of two counter-rotating cells and is convergent at the surface. The analysis of momentum balance indicates that, in addition to the pressure gradient and vertical stress divergence, nonlinear advection and horizontal stress divergence are also important contributors. During ebb phase, the lateral circulation is mostly eastward for the whole water column and persisting for almost the whole period. The surface divergence suggested by the differential advection mechanism lasts for a very short period, if it ever exists. The main momentum balance across most of the transect during ebb is between the along-channel advection of cross-channel momentum and pressure gradient. The sectional averaged lateral velocity magnitude during ebb is comparable to that during flood, which is different from the idealized numerical experiment result.

The Pythagorean fuzzy set (PFS), which is characterized by a membership and a non-membership degree and the square sum of them is less or equal to one, can act as an effective tool to express decision makers’ fuzziness and uncertainty. Considering that the Heronian mean (HM) is a powerful aggregation operator which can take the interrelationship between any two arguments, we study the HM in Pythagorean fuzzy environment and propose new operators for aggregating interval-valued Pythagorean fuzzy information. First, we investigate the HM and geometric HM (GHM) under interval-valued intuitionistic fuzzy environment and develop a series of aggregation operators for interval-valued intuitionistic fuzzy numbers (IVIFNs) including interval-valued intuitionistic fuzzy Heronian mean (IVIFHM), interval-valued intuitionistic fuzzy geometric Heronian mean (IVIFGHM), interval-valued intuitionistic fuzzy weighted Heronian mean (IVIFWHM) and interval-valued intuitionistic fuzzy weighted geometric Heronian mean (IVIFWGHM). Second, some desirable and important properties of these aggregation operators are discussed. Third, based on these aggregation operators, a novel approach to multi-attribute decision making (MADM) is proposed. Finally, to demonstrate the validity of the approach, a numerical example is provided and discussed. Moreover, we discuss several real-world applications of these operators within policy-making contexts.

This study investigated whether biogas reactor performance, including microbial community development, in response to a change in substrate composition is influenced by initial inoculum source. Test reactors were first started with two different inocula and operated with the same grass-manure mixture for more than 120 days. These reactors initially showed great differences depending on inoculum source, but eventually showed similar performance and overall microbial community structure. At the start of the present experiment, the substrate was complemented with milled feed wheat, added all at once or divided into two portions. The starting hypothesis was that process performance depends on initial inoculum source and microbial diversity, and thus that reactor performance is influenced by the feeding regime. In response to the substrate change, all reactors showed increases and decreases in volumetric and specific methane production, respectively. However, specific methane yield and development of the microbial community showed differences related to initial inoculum source, confirming the hypothesis. The different feeding strategies had however only minor effects on process performance and overall community structure, but still induced differences in the cellulose-degrading community and in cellulose degradation.

NaoMaiTong (NMT: Radix et Rhi-zoma Rhei, Radix Ginseng, Radix Puerariae, and Rhizoma Ligustici Chuanxiong as 9: 9: 6: 6) is a traditional Chinese medicine prescription for treating ischemia cerebral apoplexy. In this work, four cell injury models of ischemic stroke were establish, namely hypoxic injury, glutamate damage, injury of potassium chloride and hydrogen peroxide damage model. The protective effects of NMT and its single herbs-containing sera of different time points on PC12 cell damage were evaluated respectively, and the corresponding efficacy-time curves were drawn. Cell viability was measured by MTT (3-(4,5)-Dimethylthiahiazo(-z-y1)-3,5-di-phenytetrazoliumromide) assay. Furthermore, an statistical methods of support vector machine (SVM) were used to establish the correlation between concentration-time-efficacy for the first time. These results revealed that NMT-containing serum has obvious protective effect on the four injury models and can significantly improve cell viability. The PK-PD correlation between fifteen ingredients in the NMT compound with four model efficacy indexes indicated that rhein, puerarin, and 3'-methoxy puerarin might be the most important constituents controlling the pharmacological effects of NMT. The study suggested that these fifteen components are likely to be the material basis of NMT and recommended to increase the amounts of Pueraria in the NMT compound. That provided the scientific basis and demonstration for the research of efficacy material base of Traditional Chinese Medicine (TCM).

A novel plasma source of pulsed electrolyte cathode atmospheric pressure discharge (pulsed-ECAD) driven by an alternating current (AC) power supply coupled with a high voltage diode was generated, and the discharge was generated in the open-to-air atmosphere between a metal electrode and a small-sized flowing liquid cathode. The spatial distribution of plasma temperatures (excitation, vibrational and rotational) of the pulsed-ECAD were investigated. The electron excitation temperature of H T_exc(H), vibrational temperature of N₂ T_vib(N₂), and rotational temperature of OH T_rot(OH) were measured as 4900±36-6800±108 K, 4600±86-5800±100 K and 1050±20-1140±10 K, respectively. Meanwhile, the temperature characteristics of dc solution cathode glow discharge (dc-SCGD) were also studied for comparison with pulsed-ECAD. The effects of operating parameters, including discharge voltage and discharge frequency, on the plasma temperatures were investigated. The electron number density determined in the discharge system and dc-SCGD were within the range (3.8–18.9) ×10¹⁴ cm^-3 and 2.6×10¹⁴-17.2×10¹⁴ cm^-3, respectively.

For planetary gear has the characteristics of small volume, light weight and large transmission ratio, it is widely used in high speed and high power mechanical system. Poor working conditions result in frequent failures of planetary gear. A method is proposed for diagnosing faults in planetary gear based on permutation entropy of Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN) Adaptive Neuro-fuzzy Inference System (ANFIS) in this paper. The original signal is decomposed into 6 intrinsic mode functions (IMF) and residual components by CEEMDAN. Since the IMF contains the main characteristic information of planetary gear faults, time complexity of IMFs are reflected by permutation entropies to quantify the fault features. The permutation entropies of each IMF component are defined as the input of ANFIS, and its parameters and membership functions are adaptively adjusted according to training samples. Finally, the fuzzy inference rules are determined, and the optimal ANFIS is obtained. The overall recognition rate of the test sample used for ANFIS is 90.75%, and the recognition rate of gear with one missing tooth is relatively high. The recognition rates of different fault gears based on the method can also achieve better results. Therefore, the proposed method can be applied to planetary gear fault diagnosis effectively.

Social recommendation is almost as the integration of the business platform and social platform, and gradually become a top in recommendation system. Social recommendation algorithm solves the problem of cold start and data sparseness for traditional commodity, while the internal structure of the relationship graph in social relations has not been fully excavated. This paper proposes two models of Micro Relation Transfer Model and Macro Relation Transfer Model of social relations, and applies the social relations transfer models into the social recommendation system. A relationship graph is built from the relationship between customers on the Internet. Micro Relation Transfer Model establishes the transfer activation function by calculating the relationship between the two customers using the similarity of interests set. Micro Relation Transfer Model spreads the relationship of friends by calculating the proportion of common neighbors held by the customer's social relations. In order to effectively control the transmission range and effect of social relations graph, we introduce pruning algorithm based on Monte Carlo Decision Tree convergence algorithm. The experimental results show that SRRTC algorithm enhances the success rate and stability significantly.

With the increasing of copper consumption, the in-use stock of copper tends to increase. This paper used the “average use life method” to quantify the amount of copper in-use stock, and calculated the average age of in-use stock. It was indicated that the total in-use stock had an overall smooth trends, and reached its peak in 2007 was about 68.9 Mt (million tons), in addition, in-use stock per capita reached its peak ,234 kg/capita in 2001. The results demonstrated that during the period 1992-2002, the average age of copper in-use stock was continually decreased, but gradually increased since the year 2003. The fixed assets depreciation method used in this paper is applied to analyze depreciated copper in-use stock, and to analyze the relationship with economic indicator (GDP). It is demonstrated that it was inconsistent with the theory of Environmental Kuznets Curve (EKC) before 2000, this might be the demand for copper in the service sector is greater than the reduced strength of alternatives. Finally, scenario analysis of future copper in-use stock and depreciated copper in-use stock per capita in the U.S. were presented. The corresponding average age of the in-use stock will have a slight rise in the next decade.