The current study aimed to investigate the effects of feeding silage of Napier Pakchong 1 fermented with mung bean concentrate on production performance, nutrient digestibility, carcass yield, and meat quality of male dairy goats. Silage made for experimental treatments was prepared as follows: Treatment 1 (T1) containing 100% Napier Pakchong 1 grass (without mung bean concentrate added) as a control, while Treatment 2 (T2) and Treatment 3 (T3) containing 90% and 80% Napier Pakchong 1 grass, respectively, mixed with 10% and 20% mung bean concentrate, respectively. Fifteen weaned male Saanen-growing goats were assigned to 3 experimental treatments in a completely randomized design; the study lasted for 150 days. The nutritive value of feed, production performance, nutrient digestibility, blood urea nitrogen, carcass yield and dressing, basic meat quality, and composition of meat were collected or analyzed. The results found that the goats fed with the silage made from Napier Pakchong 1 added 10% and 20% mung bean concentrate showed improvements in nutritive value, growth rate, key nutrient digestibility, blood urea nitrogen, carcass yield, the water-holding capacity of cooked meat, and fat content in meat. However, adding 10% mung bean concentrate had a trend of more beneficial value added into the production chain of male Saanen dairy goats for meat purposes. Thus, silage made from Napier Pakchong 1 fermented with 10% mung bean concentrate as a roughage source for male Saanen dairy goats intended for meat purposes is recommended.

Early weaning of piglets caused excessive concentration of free radicals, which would oxidize and damage the intestinal tract of piglets, resulting in dyspepsia, low growth, diarrhea, microbiota disorders and intestinal infections. This research studied on effect of different levels of taurine in diets on intestinal oxidative damage in early weaned piglets. A total of 48 weaned piglets (6.71 ± 0.73 kg) of 28-day-old crossbred "Duroc × Landrace × Yorkshire" were assigned to 4 groups with 12 replicates per group and 1 pig per replicate: piglets were fed a basal diet with 0.0% (CON), 0.2% taurine (L-Tau), 0.3% taurine (M-Tau), or 0.4% taurine (H-Tau). The animal experiment lasted for 30 days. With the increase of dietary taurine dosage, the activity of antioxidant enzymes including superoxide dismutase（SOD）,glutathione peroxidase（GPX）,catalase（CAT） and peroxidase（POD） were up-regulated (Linear, P < 0.05), the mRNA abundance of antioxidant enzymes including SOD1, SOD2, GPX1 and heme oxygenase-1（HO-1）were up-regulated (P < 0.05), glutathione (GSH) concentrations was up-regulated (Linear, P < 0.05) , nitric oxide (NO), malondialdehyde (MDA) and oxidized glutathione (GSSG) concentrations were down-regulated (Linear, P < 0.05);The villus height (VH) and villus height/ crypt depth (VH/CD) of jejunum and ileum were increased (Linear, P < 0.05); The expression of tight junction proteins including zonula occludens protein 1(ZO-1), occludin (OCLN) and closure protein 1(CLDN-1) in the jejunum mucosa were up-regulated (Linear, P < 0.05), the mRNA abundance of ZO-1, OCLN and CLDN-1 were up-regulated (P < 0.05),and the D-lactose (D-LA) content in blood was down-regulated (Linear, P < 0.05); the colonization abundance of Firmicutes was increased (Linear, P < 0.05), while Proteobacteria and Spirochaetota was decreased (Linear, P < 0.05); The diarrhea index decreased (Linear, P < 0.05), while the feed conversion rate increased (Linear, P < 0.05). Collectively, supplementation of 0.3% and 0.4% taurine in feed can significantly alleviate intestinal oxidative damage by enhancing antioxidant capacity of piglets, and improve feed utilization of piglets after repairing intestinal damage.

The building and construction sector has a significant impact on CO2 emissions and pollutants released into the atmosphere, which contribute to climate change. The EPDB Directive mandates the achievement of a minimum energy class E for all residential buildings by 2030 and an energy class D by 2033. Particularly, in Italy, about 86% of the existing building stock predates the enactment of any energy laws and regulations, making it imperative to apply the energy efficiency interventions. This paper provides a support decision tool for the identification of standardized interventions on the envelope, air conditioning system and domestic hot water production. The study is focused on a specific construction period class (1976 - 1990) in six different climatic zones. The methodological approach is based on a cataloguing phase and definition of Ante Operam energy classes, on the case study identification, the energy requalification interventions identification, solutions simulations, cost estimation. By simulating standardized interventions for each climatic zone, a range of possible combinations will be identified. The most advantageous ones will be determined based on a cost-benefit analysis, considering the potential class jump achieved. The research result is a matrix of energy efficiency interventions that is applicable to each climatic zone and can be extended to the existing housing stock.

We present evidence of the anchoring bias and disposition effect (DE) in investor trading decisions across different asset markets (stable and volatile assets) and market scenarios (stable and volatile markets), as well as how these biases affect investors' portfolio performance. The study employs a quasi-experimental design, allowing subjects to engage in interactive trading with four securities, two with potential negative returns and two with potential positive returns, within a simulated asset market. Our findings reveal the presence of the disposition effect and anchoring bias among individual investors in India. Second, market scenarios or volatility can influence the investors’ behavioral biases. The disposition effect was more prominent in volatile markets and the total market, while the anchoring bias was significant in stable and total markets. Additionally, investors exhibiting the disposition effect exhibit lower portfolio performance, while those demonstrating anchoring bias perform relatively better. The study's findings can help individual investors understand their behavioral biases, avoid them in future trading decisions, and improve portfolio performance. Financial institutions and regulatory agencies could identify investment products and supportive investor interactions towards better market trade decisions.

Drafting formations have been long recognized as highly effective for reducing drag and enhancing athletic performance, particularly in race walking events. The precise spacing and positioning of the race walkers are critical to optimizing the effectiveness of drafting. In this study, the drag reduction of 15 drafting formations is investigated using wind-tunnel experiments and CFD numerical simulations. The results show excellent consistency in drag reduction rate between the two methods, with differences being within 10%. This can be attributed to spacing replacing body shape differences as the primary factor influencing drag reduction. Optimal double, triple, and quadruple drafting formations produce the same results in both wind-tunnel experiments and CFD simulation, resulting in drag reductions of 67%, 66%, and 81% (wind-tunnel) and 65%, 72%, and 85% (CFD). The sources of drag differences in the two methods are discussed from various aspects. The flow field obtained through CFD analysis is used to examine the mechanism of drag reduction, revealing that drafting formations have a significant shielding effect on incoming air, which reduces the number and speed of airflow impacting the core race walker. This shielding effect is identified as the primary cause of drag reduction. Using an empirical model for mechanical power output, optimal double, triple, and quadruple drafting formations enhance sport economy (4.4-5.7%), speed (3.61-4.67%), and performance (173.8-223.3s) compared to race walking alone. The findings can serve as a reference for race walkers' positioning strategy and provide insights for considering drafting formations in various running events.

This study aimed to evaluate the effects of a palygorskite-based antibacterial agent (PAA) as an alternative to antibiotics on growth performance, blood parameters, rumen fermentation, and rumen microbiota in sheep. A total of 120 sheep were randomly divided into five groups of six replicates with four sheep each. Sheep were fed a basal diet, an antibiotic diet supplemented with 500 g/t chlortetracycline (CTC), and a basal diet supplemented with 500, 1,000, and 2,000 g/t PAA for 80 d, respectively. Supplementation with 2,000 g/t PAA and 500 g/t CTC increased the average daily gain (ADG) of sheep compared with the control group (P < 0.05). Diets supplemented with 2,000 g/t PAA and 500 g/t CTC reduced (P < 0.05) the feed: gain (F/G ratio) in the overall periods. Dietary Supplementation with 1,000 g/t PAA significantly increased albumin and total protein (P < 0.05). A significant positive correlation was found between growth hormone concentration and PAA supplementation (P < 0.05). In addition, compared to the control group, the CTC group had higher growth hormone concentration and lower lipopolysaccharide concentration (P < 0.05). No dif-ference was observed between the five groups in terms of rumen fermentation characteristics (P > 0.05). At the phylum level, the relative abundance of Proteobacteria was lower in the PAA 2000 and CTC 500 groups than that in the control and PAA 500 groups (P < 0.05). At the genus level, a sig-nificant decrease (P < 0.05) in the relative abundance of RuminococcaceaeUCG-010 was observed in the PAA 1000, PAA 2000, and CTC 500 groups compared with that in the control group. In addition, the relative abundance of Prevotella1 (P < 0.05) was higher in the PAA 2000 group than that in the control group. These findings indicate that dietary supplementation with PAA has ameliorative effects on growth performance, blood parameters, and rumen microbiota, with an optimal dosage of 2,000 g/t for sheep.

Vernacular architecture constitutes a rich source of information and ancestral knowledge that can become a key resource for sustainable development through its passive design strategies, which effectively respond to local climatic and weather conditions using locally sourced materials for the construction of its supporting structure and enveloping elements, as well as spatial organization and the incorporation of a buffer area (patio) that optimize the use of renewable resources. This qualitative study analyzes a traditional housing typology with a central patio located in the Historic Center of Azogues city, Ecuador, to evaluate its interior thermal comfort through in-situ monitoring in the different building spaces. Using the open-source software Open Studio and EnergyPlus, a simulation model was built to assess the annual thermal performance of the house. Field records were used to verify the effectiveness of the strategies that respond to the climatic conditions of the area. The analysis carried out on the passive strategies used in the selected house with regard to natural ventilation, solar protection, and thermal insulation, which depend on various aspects of the building, such as its location, internal space arrangement, design of openings (doors and windows), among others. The thermal simulations reveal that the traditional house located in the Historic Center of Azogues city is well adapted to the local climate, although interior thermal comfort is not entirely satisfactory.

The affected upper limb in children with Unilateral Spastic Cerebral Palsy (US CP) has motor and somatosensory impairments, that contribute negatively to children’s bimanual performance and quality of life. Mirror Therapy (MT) is being studied to become an approachable intensive and home-based therapy, suitable for children with US CP. The aim of this study is to examine the feasibility of a 5-week home-based program of MT for children with US CP. Six children aged 8-12 years old performed the therapy, five days per week, 30 minutes per day. A minimum of an 80% of compliance was required. The evaluations included the feasibility of the therapy (compliance, total dosage, perceived difficulty of the exercises, and losses of follow-ups and evaluations), the bimanual performance, the somatosensory function and the quality of life at baseline, at the end of the intervention, and at 1-month follow-up. All children completed the therapy and were included in the analysis. The total accomplishment was 86.47 ± 7.67. The perceived difficulty of the exercises ranged from 2,37 to 4,51. As a conclusion, a home-based program of Mirror Therapy is suitable and feasible for children with US CP.

When drilling oil and gas wells, hole cleaning efficiency is crucial, particularly in the curved or severely deviated sections. Although many hole-cleaning procedures and models have been developed, most of them have substantial limitations or are difficult to apply in real time. This study aimed to develop a model for the hole cleaning index (HCI) that could be integrated into the drilling operations to provide an automated and real-time evaluation of deviated drilling hole cleaning. The new model herein was developed based on the mechanical drilling parameters, enhanced estimated drilling fluid properties, and cuttings characteristics. This HCI model was validated and tested in the field, as it was applied when drilling 12.25”-intermediate directional sections in two wells with a total length of approximately 2000 ft each. The integration of the HCI helped to attain a much better well drilling performance (50% enhancement) and mitigation of potential problems like pipe sticking and the slower rate of penetration. Since the developed index incorporates the changes in wellbore geometry and other spontaneous field data, the new model could be utilized for real-time optimization and intermediate interventions by drilling teams, unlike commercial software tools which are only useful during the planning phase. For this reason, the HCI can be linked to the driller's control panel to provide timely evaluation and corrective measures related to hole cleaning.

The study is based on the notion that big data predictive analytics is important for developing strategic alliances performance of companies. this study investigates the relationship between big data predictive analytics, big data culture, and competitive strategies 'techniques were adopted, such as descriptive statistics, correlation,regression, etc. using SPSS and SmartPLS statistical software. Hypotheses were tested with bootstrapped analysis using SEM (through SmartPLS). The study developed a structural equation model by using the SEM analysis. The results of the SEM analysis suggested the hypothesized model of the study was valid. The results supported all the hypotheses of the study.Through empirical analysis, demonstrated the conclusion is that the big data predictive analytics has a positive and significant relationship with strategic alliance performance

The paper aims to study the workflow of the detection center of stealthy attacks on industrial installations that generate increase in energy consumption while avoiding triggering fault detection and damaging the installation. Such long-lasting attacks on industrial facilities make production more expensive and less competitive. We present the concept of the remote detection system of cyberattacks directed at maliciously changing the controlled variable in an industrial process air conditioning system. The monitored signals are gathered at the PLC-controlled installation and sent to the remote detection system, where the discrepancies of signals are analyzed based on the Control Performance Assessment indices. The results of performed tests prove the legitimacy of the adopted approach.

This study analyzes the academic performance of students from an official school in Bogotá (Colombia) who had asymmetric access to Information and Communication Technologies during the first year of the Covid-19 pandemic. The Classical Linear Regression Model is employed using data from a survey of a representative group of students in the year 2020. Results show technological gaps between students that are associated with asymmetric academic performance against students with limited or null access to the Internet and electronic devices. Results also show that, among students with permanent access to the Internet, women have better scores compared to men’s scores, which implies that women can achieve better academic results than men in virtual education. It is also noted that the sole access to an electronic device does not guarantee good academic achievements if there is no full access to the Internet, and if ICT-use skills have not been developed.

Most pivotal clinical trials in advanced non-small cell lung cancer (NSCLC) have excluded patients with poor performance status (PS), and data on the efficacy and safety of pharmacotherapy have not been fully accumulated. For NSCLC patients with PS 2 and without druggable genetic alterations, monotherapy with cytotoxic agents or carboplatin-based combination therapy is usually administered based on the results of several randomized trials. However, the evidence of cytotoxic chemotherapy for patients with PS 2 is insufficient, with limited efficacy and toxicity concerns. Immune checkpoint inhibitors (ICIs) are a promising treatment for patients with PS 2 because of lower incidence of severe toxicity compared to cytotoxic chemotherapy. Meanwhile, several reports suggest that anti-PD-1 antibodies monotherapy is less effective for patients with PS 2, especially for those with PS 2 caused by disease burden. Although the combination therapy of nivolumab and ipilimumab is a promising treatment option, there is a divergence in efficacy data between clinical trials. The standard of care for advanced NSCLC with PS 2 has not been established, and future therapeutic strategies should take into account the heterogeneity of the PS 2 population.

This paper presents some results from a computational fluid dynamics (CFD) model of a multi-megawatt crosswind kite spinning on a circular path in a straight downwind configuration. The unsteady Reynolds averaged Navier-Stokes equations closed by the k−ω SST turbulence model are solved in the three-dimensional space using ANSYS Fluent. The flow behaviour is examined at the rotation plane, and the overall (or global) induction factor is obtained by getting the weighted average of induction factors on multiple annuli over the swept area. The wake flow behaviour is also discussed in some details using velocity and pressure contour plots. In addition to the CFD model, an analytical model for calculating the average flow velocity and radii of the annular wake downstream of the kite is developed. The model is formulated based on the widely-used Jensen’s model (Technical Report Risø-M; No. 2411, 1983), which was developed for conventional wind turbines, and thus has a simple form. Expressions for the dimensionless wake flow velocity and wake radii are obtained by assuming self-similarity of flow velocity and linear wake expansion. Comparisons are made between numerical results from the analytical model and those from the CFD simulation. The level of agreement was found to be reasonably good. Such computational and analytical models are indispensable for kite farm layout design and optimization, where aerodynamic interactions between kites should be considered.

Although the relations between sleep and academic performance have been extensively examined, how sleep predicts future academic performance (e.g., 2 -3 years) remains to be further investigated. Using wearable smartwatches and a self-report questionnaire, we tracked sleep activities of 45 college students over a period of approximate half a month to see whether their sleep activities predicted their academic performance, which was estimated by grade point average (GPA). Results showed that both nighttime sleep awakening frequency and its consistency in the tracking period were not significantly correlated with the GPA for the courses taken in the semester during sleep tracking (current GPA). However, both nighttime sleep awakening frequency and its consistency inversely predicted the GPA for the rest of the courses taken after that semester (future GPA). Moreover, students with more difficulty staying awake throughout the day obtained lower current and future GPAs, and students with lower inconsistency of sleep quality obtained lower future GPA. Together, these findings highlight the importance of nighttime sleep awakening frequency and consistency in predicting future academic performance and emphasize the necessity of assessing the consistency of sleep measures in future studies.

Steady-state Reynolds-Averaged Navier-Stokes (RANS) simulations are performed for a leading-edge inflatable wing for airborne wind energy applications. Expanding on previous work where only the inflatable leading edge tube was considered, eight additional inflatable strut tubes that support the wing canopy are now included. The shape of the wing is considered to be constant. The influence of the strut tubes on the aerodynamic performance of the wing and the local flow field is assessed, considering flow configurations with and without side-slip. The simulations show that the aerodynamic performance of the wing decreases with increasing side-slip component of the inflow. On the other hand, the chordwise struts have little influence on the integral lift and drag of the wing, irrespective of the side-slip component. The overall flow characteristics are in good agreement with previous studies. In particular, it is confirmed that at a low Reynolds number of Re=10^5, a laminar separation bubble exists on the suction side of this hypothetical rigid wing shape with perfectly smooth surface. The destruction of this bubble at low angles of attack impacts negatively on the aerodynamic performance.

In this paper, a new design of a helium-assisted hybrid drone is proposed for flight time enhancement. As is widely known, most of the drones with a VTOL (vertical take-off and landing) feature have a short operation time, limiting their capability to carry out sustainable operations for the given missions. Thus, with the clear goal of enhancing the flight time, this study aims to develop a hybrid drone system, where a helium balloon is used to provide a lifting force for this purpose. The proposed design for the hybrid drone has several benefits including easiness to manufacture and relatively small size when compared to other types of hybrid drones. Various analyses are conducted for the design of the hybrid drone system including the balloon shape and size, buoyant force, flight time, and connector design. Since stability and performance are one of the most important issues for the new design, the pole location analysis is conducted based on the control theory. This rigorous analysis provides that the proposed hybrid drone design is stable as well as robust against swinging motions. To validate the effectiveness of the proposed design and flight time enhancement, simulations were conducted and experimental results are also provided using the manufactured hybrid drone system. Through the real experiments, it is proved that the hybrid drone can increase the flight time more than 2.5 times while guaranteeing stable motions.

This study aims to develop a performance evaluation system that can facilitate performance evaluation at region, hospital, and department levels to enable better cost management for sustainable development. A multi-level system of performance evaluation informs a hierarchical assessment of cost management from regions to hospitals to departments using diagnosis-related group (DRGs). Various metrics are developed employing the variances between targets and actuals where targets are determined from two perspectives: benchmarking using external regional prices and change management using internal data. Targets for the latter are statistically based and specifically incorporate variability. The model is applied to two hospitals, twenty departments, nine DRGs and 1071 inpatients. The analyses indicate that the approach can provide a practical evaluation tool that allows for particular characteristics at multiple levels. The system provides macro-micro and external-internal perspectives in performance, enabling high-level variances to be decomposed thereby identifying sources of performance variability and financial impact.

The study takes into account different classes of tunnel boring machines (TBMs), with the aim of identifying correlation models which are meant to estimate, at a preliminary design phase, the construction time of a tunnel and to evaluate the mechanical and operational parameters of the TBMs, starting from the knowledge of the tunnel length and/or the excavation diameter. To achieve this goal, first of all a database was created, thanks to the collection of the most meaningful technical parameters from a large number of tunnels; afterward, it was statistically analysed through Microsoft Excel. In a first phase, forecasting models were identified for the three types of machines investigated, separately for compact rocks (open TBM) and fractured rocks (single and double shield TBM). Then, the mechanical parameters collected through the database were analysed, with the aim of obtaining models that take into account, in addition to the type of TBM, the geological aspect, and the type of rock characterising the rock mass. Finally, the validation of the study was proposed in a real case, represented by the Moncenisio base tunnel, a work included in the new Turin–Lyon connection line. The estimated values were compared with the real ones, in order to verify the accuracy of the experimental models identified.

In this paper a novel and flexible solution for fault prediction based on data collected from Supervisory Control and Data Acquisition (SCADA) system is presented. Generic fault/status prediction is offered by means of a data driven approach based on a self-organizing map (SOM)and the definition of an original Key Performance Indicator (KPI). The model has been assessed on a park of three photovoltaic (PV) plants with installed capacity up to 10 MW, and on more than sixty inverter modules of three different technology brands. The results indicate that the proposed method is effective in predicting incipient generic faults in average up to 7 days in advance with true positives rate up to 95%. The model is easily deployable for on-line monitoring of anomalies on new PV plants and technologies, requiring only the availability of historical SCADA data, fault taxonomy and inverter electrical datasheet.

When focusing on materials science in civil engineering, the current trend is to investigate the use of innovative solutions in order to enhance thermal and energy performances. This trend is amplified with the need for a sustainable development strategy for the construction sector. This paper assesses the integration of a Phase Change Material (PCM) in cement intended for building construction. The key characteristic of PCMs is their capacity to absorb energy and restore it. In building construction, this feature could be harnessed to save energy by incorporating PCMs in the materials used. In this study, passive integration of PCM in cement was tested and thermal properties of such an integration was assessed. The results provide insights into how PCMs affect cement as part of the concrete mixture, thus identifying the contribution of PCM-based cements in concrete mixtures.

Long-term durability of the vacuum edge-seal plays a significant part in retrofitting triple vacuum glazing (TVG) to existing buildings in achieving towards zero-energy buildings (ZEB) target. Vacuum pressure decrement with respect to time between panes affect the thermal efficiency of TVG. This study reports a 3D finite element model, with validated mathematical methods and comparison, for the assessment of the influence of vacuum pressure diminution on the thermal transmittance (U value) of TVG. The centre-of-pane and total U values of TVG calculated to be 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ at the cavity vacuum pressure of 0.001 Pa. The results suggests that a rise in cavity pressure from 0.001 Pa to 100 kPa increases the centre-of-pane and total U values from 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ to 2.4 Wm⁻²K⁻¹ and 2.58 Wm⁻²K⁻¹, respectively. The temperature descent on the surfaces of TVG between hot and cold sides’ increases by decreasing the cavity vacuum pressure from 50 kPa to 0.001 Pa. To maintain the cavity vacuum pressure of 0.001 Pa for over 20 years of life span in the cavity of 10 mm wide edge sealed triple vacuum glazing, non-evaporable getters will maintain the cavity vacuum pressure that will enable the long-term durability to TVG.

Performance of flow through orifices on a perforated distribution pipe between periods with and without partial clogging (submersion of part of the distribution pipe) was compared. The distribution pipe directly receives runoff and delivers it to an underground infiltration bed. Partial clogging appeared in winter but reduced in summer. Performance was defined as flow rate divided by l_eff (h_(d,mean)^0.5) where h_(d,mean) is the mean pressure head that drives flow and l_eff is the effective pipe length (length of water column with pipe water volume and the pipe cross-sectional area). ANCOVA (ANalysis of COVAriance) was adopted to examine the clogging effects with flow rate plotted against l_eff (h_(d,mean)^0.5) . Partial clogging had a significant effect on pipe performance during periods of low or no rainfall. However, if only data during larger storms was considered, little evidence showed that partial clogging had effects on pipe delivery performance. Partial clogging might be caused by leaves accumulated in the lower section of the pipe in winter, and its effect was insignificant when water level rose in the pipe, utilizing significantly more orifices on the distribution pipe, thus the effect from the clogged portion had negligible impact on system performance. Larger storms might also provide the required flow rate to move the debris block thus exposing the orifices. Partial clogging did not increase the tendency of overflow; therefore, current maintenance schedule was sufficient to keep the distribution pipe at satisfactory performance even though partial clogging can exist.

The use of mindfulness techniques as a cutting-edge tactic to reduce catastrophic risk in the chemical sector is examined in this study. Constructed from fundamental design principles and conventional safety measures, mindfulness provides an additional method for addressing the behavioural and cognitive aspects of risk management. The study looks at the safety paradigms' development, the historical background of significant industrial accidents, and the theoretical foundations of mindfulness in high-reliability businesses. Through the promotion of increased consciousness, better judgement, and better communication, mindfulness has the potential to build a safer culture that is more resilient. The study investigates practical implementation challenges and the measurable outcomes of mindfulness-based interventions in high-risk industrial settings. This multidisciplinary study adds to the continuing conversation about industrial safety by offering insightful information to safety experts, business executives, and legislators. The necessity for additional empirical research to measure the effectiveness of mindfulness therapies in various chemical industry situations is emphasised in the paper's conclusion.

Approximate Computing (AxC) has emerged as a promising paradigm to enhance performance and energy efficiency by allowing a controlled trade-off between accuracy and resource consumption. It is extensively adopted across various abstraction levels, from software to architecture and circuit levels, employing diverse methodologies. The primary objective of AxC is to reduce energy consumption for executing error-resilient applications, accepting controlled and inherently acceptable output quality degradation. However, harnessing AxC poses several challenges, including identifying segments within a design amenable to approximation and selecting suitable AxC techniques to fulfill accuracy and performance criteria. This survey provides a comprehensive review of recent methodologies proposed for performing Design Space Exploration (DSE) to find the most suitable AxC techniques, focusing on both hardware and software implementations. DSE is a crucial design process where system designs are modeled, evaluated, and optimized for various extra-functional system behaviors such as performance, power consumption, energy efficiency, and accuracy. A systematic literature review was conducted to identify papers that ascribe their DSE algorithms, excluding those relying on exhaustive search methods. This survey aims to detail the state-of-the-art DSE methodologies that efficiently select AxC techniques, offering insights into their applicability across different hardware platforms and use-case domains. For this purpose, papers were categorized based on the type of search algorithm used, with Machine Learning (ML) and Evolutionary Algorithms (EAs) being the predominant approaches. Further categorization is based on the target hardware, including Field-Programmable Gate Arrays (FPGAs), Application-Specific Integrated Circuits (ASICs), general-purpose Central Processing Units (CPUs), and Graphics Processing Units (GPUs). A notable observation was that most studies targeted image processing applications due to their tolerance for accuracy loss. By providing an overview of techniques and methods outlined in existing literature pertaining to the DSE of AxC designs, this survey elucidates the current trends and challenges in optimizing approximate designs.

Throughout history, natural stone has been a crucial building material due to its strength, durability, and aesthetic qualities. Today, it continues to be a valuable resource, representing both a cultural heritage asset and a significant economic material. However, the increasing frequency of heat waves and fires driven by climate change poses a growing threat to stone building materials. This paper presents a literature review aimed at assessing the effects of high temperatures on Global Heritage Stone Resources (GHSR). GHSR is an international classification designed to enhance the recognition and status of building stones. The study identifies a critical need for research to better understand how those stone materials behave when exposed to high temperatures in order to predict and mitigate the effects of external threats such as fires.

Background/Objectives: Consumption of a high energy density diet (HED) leads to increased body weight and fat mass, gut dysbiosis, and obesity. The aim of this study was to characterize the initial response to HED consumption, as well as identify any sex differences, on body composition, systemic inflammation, gut microbiome, and fecal fat excretion in rats. Methods: Male and female Sprague-Dawley rats were fed a low energy density (LED) for 10 days and then were switched to HED for four weeks. Food intake was measured twice a week, body weight and body composition were measured weekly. Serum samples were collected to measure inflammatory cytokines/chemokines. Fecal samples were collected for microbiome analysis and lipid content. Results: Both males and females experienced increases in body weight, fat mass and fecal fat excretion, while males were more susceptible to significant weight gain, particularly in the diet-induced obesity-prone (DIO-P) group. Males showed elevated TGF-β levels, while females exhibited increases in IP-10, RANTES, and FGFb. Changes in gut microbiota composition revealed a reduction in beneficial species like Bacteroides uniformis and Parabacteroides distasonis and an increase in species such as Akkermansia muciniphila. Sex differences in fat metabolism were shown in the greater fecal fat excretion observed in males. Conclusions: Our study demonstrates that short-term consumption of a high-energy diet elicits notable sex-specific differences in body weight, body composition, inflammatory markers, gut microbiota, and fat excretion in Sprague-Dawley rats. These findings underscore the importance of considering sex as a biological variable in studies of diet-induced obesity and its metabolic consequences.

The growth of photosynthetic organisms requires specific ranges of temperature and photosynthetically active radiation that are technically difficult to achieve and control, especially in outdoors cultures. In such cases, a typical meteorological sequence can be a useful tool to estimate the growth of photosynthetic organisms. This work proposes a new methodology based on long-term meteorological sequences to simulate the growth of photosynthetic organisms. A case of study that addresses the simulation of the growth of microalgae (Chlorella vulgaris) in Riosequillo, north of the Madrid region (Spain), is shown for the four seasons of the year, and these estimates are then compared with the observed results of an experimental microalgae culture in domestic wastewater. The results also show great agreement with the probability distribution function of the biomass concentration per day, obtaining the best results for typical meteorological sequences of summer and spring. The methodology seems to confirm the representativeness of typical meteorological sequences and also allows the identification of the most likely production scenarios for the feasibility analysis of projects, which has potential application in decision-making processes.

Digital image compression is applied to reduce camera bandwidth and storage requirements, but real-time lossless compression on a high-speed high-resolution camera is a challenging task. The article presents hardware implementation of a Bayer colour filter array lossless image compression algorithm on an FPGA-based camera. The compression algorithm reduces colour and spatial redundancy and employs Golomb-Rice entropy coding. A rule limiting the maximum code length is introduced for the edge cases. The proposed algorithm is based on integer operators for efficient hardware implementation. The algorithm is first verified as a C++ model and later implemented on Xillinx Zynq UltraScale+ device using VHDL. An effective tree-like pipeline structure is proposed to concatenate codes of compressed pixel data to generate a bitstream representing data of 16 parallel pixels. The proposed parallel compression achieves up to 56% reduction in image size for high resolution images. Pipelined implementation without any state machine ensures operating frequencies up to 320 MHz. Parallelised operation on 16 pixels effectively increases data throughput to 40 Gbit/s while keeping total memory requirements low due to real-time processing.

The rapid expansion of flexible and wearable electronics has necessitated a focus on ensuring their safety and operational reliability. Gel Polymer Electrolytes (GPEs) have become preferred alternatives to traditional liquid electrolytes, offering enhanced safety features and adaptability to the design requirements of flexible lithium-ion batteries. This review provides a comprehensive and critical overview of recent advancements in GPEs technology, highlighting significant improvements in their physicochemical properties, which contribute to superior long-term cycling stability and high-rate capacity compared to traditional organic liquid electrolytes. Special attention is given to the development of smart GPEs endowed with advanced functionalities such as self-protection, thermotolerance, and self-healing properties, which further enhance battery safety and reliability. The review also critically examines the application of GPEs in high-energy cathode materials, including Lithium Nickel Cobalt Manganese (NCM), Lithium Nickel Cobalt Aluminum (NCA), and thermally stable Lithium Iron Phosphate (LiFePO4). Despite the advancements, several challenges in GPE development remain unresolved, such as improving ionic conductivity at low temperatures and ensuring mechanical integrity and interfacial compatibility. The review concludes by outlining future research directions and the remaining technical hurdles, providing valuable insights to guide ongoing and future efforts in the field of GPEs for lithium-ion batteries, with a particular emphasis on applications in high-energy and thermally stable cathodes.

Arduino microcontrollers are being used for a wide range of technological and biomedical applications such as image classification, computer vision, brain-computer interaction and vision experiments. Here I present a new cost-effective mini-device based on RGB LED flicker stimulation for the assessment of polychromatic temporal resolution of visual function. The visual device configuration allows for relative luminance thresholding, mono- and polychromatic critical flicker fusion frequency assessment. The results demonstrate the steady white visual perception of a trichromatic flicker stimulus beyond the critical flicker fusion frequency, as predicted by Talbot´s law for monochromatic stimuli. The trichromatic critical flicker fusion frequency (tFCC) depends on the relative luminance threshold at the light-adaptation level. Finally, wavefront measurements demonstrate that high-order aberrations improve the temporal resolution of visual function.

Primary Ciliary Dyskinesia (PCD) is a rare genetic disorder characterized by alterations in motile cilia func-tion. The diagnosis of PCD is challenging due to the lack of standardized methods in clinical practice. High-speed video microscopy analysis (HSVA) directly evaluates ciliary beat frequency (CBF) in PCD. Recently, open-source ciliary analysis software applications have shown promise in measuring CBF accurately. How-ever, there is limited knowledge about the performance of different software applications, creating a gap in understanding their comparative effectiveness in measuring CBF in PCD. We compared two open-source software applications, CiliarMove and Cilialyzer, against the manual count method. We used videos rec-orded at high-speed of nasal ciliary brush samples from PCD patients and healthy controls. All three meth-ods showed lower median CBF values in PCD patients than healthy controls. CiliarMove and Cilialyzer identified lower CBF in PCD patients, similar to the manual count. Cilialyzer, CiliarMove and manual count demonstrated statistical significance (p-value < 0.0001) in the difference of median CBF values be-tween PCD and healthy controls. These findings support the utility of open-source software-based analysis tools. Further studies are needed to validate these findings with other genetic variants and identify the op-timal software for accurate CBF measurement in PCD.

Background: Potential calcium-related adverse events of vitamin D supplement use have not been addressed in large-scale, real-world data so far. Methods: Leveraging data from the UK Biobank, encompassing 445,493 individuals aged 40-69, we examined associations of high 25-hydroxyvitamin (25[OH]D) levels ≥100 nmol/L and vitamin D supplementation with hypercalcemia (plasma calcium >2.6 mmol/L), kidney stones, and atherosclerosis assessments (pulse wave arterial stiffness index and carotid intima-medial thickness). Regression models were comprehensively adjusted for 49 covariates. Results: Approximately 1.5% of the participants had high 25(OH)D levels, 4.3% regularly used vitamin D supplements, and 20.4% reported regular multivitamin use. At baseline, the hypercalcemia prevalence was 1.6%, and 1.1% were diagnosed with kidney stones during follow-up. High 25(OH)D levels were neither associated with calcium-related adverse events nor atherosclerosis assessments. Vitamin D and multivitamin supplementation were associated with an increased prevalence of hypercalcemia (odds ratios and 95% confidence intervals: 1.46[1.32-1.62] and 1.11[1.04-1.18], respectively) but were neither associated with atherosclerosis nor future kidney stones. Conclusion: High 25(OH)D levels observable in routine care were not associated with any adverse outcome. Vitamin D users have a slightly higher prevalence of hypercalcemia, possibly due to co-supplementation with calcium, but without higher atherosclerosis prevalence or risk of kidney stones.

Nasal high-frequency oscillatory ventilation (nHFOV) has emerged as an effective initial and rescue noninvasive respiratory support mode for preterm infants with respiratory distress syndrome (RDS). Multiple noninvasive respiratory support modes are currently available in Romania, but little is known about nHFOV use in Romanian neonatal intensive care units (NICUs). We aimed to identify the usage extent and clinical application of nHFOV in Romania. A structured web-based questionnaire was designed to find the rate of nHFOV use and knowledge of this new method of noninvasive respiratory support in Romanian level III NICUs. The questionnaire was addressed to the leaders of all level III Romanian NICUs. Using multiple-choice, open-ended, and yes/no questions, we collected information on the NICU’s size, noninvasive respiratory support modes used, nHFOV use, indications, settings, nasal interfaces, secondary effects, and equipment used. Descriptive statistics and comparisons were performed using IBM SPSS Statistics 26.0. A total of 21/23 (91.3%) leaders from level III NICUs (median [IQR] number of beds of 10 [10-17.5]) responded to the survey. The most frequently used noninvasive ventilation modes were CPAP mode on mechanical ventilators (76.2%), followed by NIPPV (76.2%), heated, humidified high flow nasal cannula (HHHFNC) (61.9%), and nHFOV (11/21 units; 52.4%); 5/11 units reported frequent nHFOV use (in 2 or more newborns/month) in both term and preterm infants. The main indications reported for nHFOV use were CPAP failure (90.9%), hypercapnia (81.8%), and bronchopulmonary dysplasia (72.7%). 10/11 units reported setting a mean airway pressure (MAP) equal to the CPAP level plus 1-2 cmH₂O on rescue nHFOV after CPAP failure. Both dedicated equipment (45.5%) and hybrid ventilators (63.6%) were used for nHFOV delivery, with face/nasal masks and short binasal prongs being the most commonly used nasal interfaces (90.9% and 72.7%, respectively). Air leaks at the interface level (90.9%), thick secretions (81.8%), and airway obstruction (63.6%) were the most frequently mentioned adverse effects of nHFOV; none of the units mentioned pneumothorax as an adverse effect. Only 3 of the NICUs had a written protocol for nHFOV use. Initial, minimum, and maximum amplitude and initial and minimum MAP settings used were significantly higher with hybrid ventilators as compared to dedicated equipment (p<0.05). Most units not yet using nHFOV cited lack of equipment, experience, training, or insufficient information and evidence for the clinical use and outcome of nHFOV use in neonates as the main reasons for not implementing this noninvasive respiratory mode. Our survey showed that nHFOV is already used in more than half of the Romanian level III NICUs to support term and preterm infants with respiratory distress despite a lack of consensus regarding indications and settings during nHFOV. A need for training for nHFOV use was identified, and efforts are needed at the national level to develop courses and training sessions, including using simulation workshops, to offer more information on optimal nHFOV use in clinical practice.

Neutron beams are an essential tool to investigate material structure and perform non-destructive analysis, as they give unique access to element composition, thus ideally complementing density analysis allowed by standard X-rays investigation. Laser-driven neutron sources, though compact and cost-effective, currently have lower average flux than conventional neutron sources, due to the limited repetition rate of the lasers used so far. However, advancements in laser technology allow nowadays to address this challenge. Here we report results obtained at the Advanced Laser Light Source (ALLS) characterizing stable production of broadband (0.1-2 MeV) neutrons produced at a high repetition rate (0.5 Hz). The interaction of laser pulses of 22 fs duration and 3.2 J on-target energy with 2-µm-thick tantalum targets produced protons in the Target Normal Sheath Acceleration (TNSA) regime up to 7.3 MeV. These protons were subsequently converted into neutrons by (p,n) reactions in Lithium fluoride (LiF). Activation measurements and bubble detectors were used to characterize neutron emissions, with a neutron fluence of up to ~ 1.4 × 10⁵ neutrons/shot/sr, and energies mainly between a few hundred of keV and 2 MeV. The total neutron yield was ~ 5 × 10⁵ neutrons/shot. This paves the way for numerous applications, e.g. in homeland security, material science or cultural heritage.

Progress in laser-driven proton acceleration requires increasing the proton maximum energy and laser-to-proton conversion efficiency, while reducing the divergence of the proton beam. However, achieving all these qualities simultaneously has proven challenging experimentally, the increase in beam energy often coming at the cost of beam quality. Numerical simulations suggest that coupling multi-PW laser pulses with ultrathin foils could offer a route for such simultaneous improvement. Yet experimental investigations have been limited by the scarcity of such lasers and the need for very stringent temporal contrast conditions to prevent premature target expansion before the pulse maximum. Here, combining the newly commissioned Apollon laser facility that delivers high-power ultrashort (∼24fs) pulses, with a double plasma mirror scheme to enhance its temporal contrast, we demonstrate the generation of up to 35 MeV protons with only 5 J of laser energy. This approach also achieves improved laser-to-proton energy conversion efficiency, reduced beam divergence, and optimized spatial beam profile. Therefore, despite the laser energy losses induced by the plasma mirror, the proton beams produced by this method are enhanced on all accounts compared to those obtained under standard conditions. Particle-in-cell simulations reveal that this improvement results from the intensified electrostatic field caused by a more compact hot-electron distribution.

Simple summary This reassessment of the findings from our Phase I/II study seeks to evaluate the effectiveness of SBRT for treating local intermediate-high risk prostate cancer in the absence of androgen-deprivation therapy due to patient’s refusal, with a median follow-up of 6.5 years. Our primary focus is on analysing the treated areas compared to recurrence patterns in the seven patients who experienced local relapse. Additionally, we provide updated data on late toxicities of grade 2 or higher, both genitourinary and gastrointestinal. Abstract Objectives: We investigated spatial patterns between primary and recurrent tumor sites and assessed long-term toxicity after dose escalation stereotactic body radiation therapy (SBRT) to the dominant intraprostatic nodule (DIN). Materials and methods: In 33 patients with intermediate-high risk prostate cancer (PCa), doses up to 50 Gy were administered to the DIN. Recurrence sites were determined and compared to the original tumor development sites through multiparametric MRI and 68Ga-labelled prostate-specific membrane antigen (PSMA) positron emission tomography/computed tomography (68Ga-PSMA-PET/CT) images. Overlap rates, categorized as 75% or higher for full overlap, and 25-74% for partial overlap, were assessed. Long-term toxicity is reported. Results: All patients completed treatment, with only one receiving concomitant androgen deprivation therapy (ADT). Recurrences were diagnosed after a median of 33 months (range: 17-76 months), affecting 13 out of 33 patients (39.4%). Intraprostatic recurrences occurred in 7 patients (21%), with ≥ 75% overlap in two, a partial overlap in another two, and no overlap in the remaining three patient. Notably, 5 patients with intra-prostatic recurrences had synchronous bone and/or lymph node metastases, while six patients had isolated bone or lymph node metastasis without intraprostatic recurrences. Extended follow-up revealed grade 2 or higher late GU and GI toxicity in 18% (n=6) and 6% (n=2) of the patients. Conclusions: Among patients with intermediate-high risk PCa undergoing focal dose-escalated SBRT without ADT, DIN recurrences were infrequent. When present, these recurrences were typically located at the original site or adjacent to the initial tumor. Conversely, relapses beyond the DIN and in extra-prostatic (metastatic) sites were prevalent, underscoring the significance of systemic ADT in managing this patient population. Advances in knowledge: focal dose escalated prostate SBRT prevented recurrences in the dominant nodule, however extra-prostatic recurrence sites were frequent.

Students have historically fared poorly on the West African Examinations Council’s (WAEC) mathematics exam. This study investigated senior high school students’ difficulties with studying Geometry in the Cape Coast Metropolis, Central Region, Ghana. Using the descriptive survey design, data were collected from 300 Senior High School Two (SHS 2) students using simple random sampling. Students responded to the questionnaire and a 30-item multiple-choice achievement test on geometry. Four geometry concepts students perceived difficult to study are Circle theorems, Perpendicularity of Tangent and radius of a circle, Angle between Tangent and a chord and Tangents from an external point. The reasons for the difficulty in studying geometry topics are the unavailability of instructional materials, the geometry topics being complex, and teachers not teaching geometry concepts to the students’ understanding. Students’ gender did not influence the learning of concepts in geometry at a 0.05 level of significance. There was an insignificantly weak positive correlation between the students’ performance and their perceived difficult geometry concepts. It was concluded that the Ministry of Education does not provide relevant instructional materials to the various schools to teach geometry concepts. Schools do not organise workshops and seminars for teachers on effectively teaching geometry concepts in mathematics.

An innovative superconducting mechanism was developed based on a patented discovery of high temperature superconductivity in several thorium (Th) salts or compounds. The rationale behind this discovery is through the experimental results about the unique electronical and magnetic properties of these Th salts. Accordingly, this new superconducting mechanism for these Th salts was obtained through the analyses of the compounds’ molecular configurations and the packings of their relevant crystal structures. Owing to the distinctive properties of the Th compounds in this discovery, we further established a different electron pairing scheme as opposed to the pairing of the Cooper pairs. Compared to the long distance electron pairing of the Cooper pairs, the new electron pairing in our mechanism is constructed by two closely correlated electrons that reside on the same atomic orbital of the Th cation as an electron lone pair. In this new superconducting mechanism, the Th cation is sitting on a relevant crystallographic lattice arrangement or a network of the relevant Th compounds. This network is constructed by many Th cations along certain crystallographic lattice arrangement where each Th cation contains one electron lone pair. This network allows the electron lone pairs on the Th cations to be delocalized over the network, “in pair”, and thus, reveals the electron lone pair in presence in a long distance fashion. The closely correlated electron lone pairs hop on this network and thus construct the supercurrent over the network. This explanation about the superconductivity laid the basis for our superconducting mechanism. All these conclusions came from the previous studies about these compounds that illustrated their unusual features of a coexistence of high electrical conductivity and diamagnetism. These electrical and magnetic properties fall in line with that of superconductors but, surprisingly, these Th compounds have such properties at the ambient condition, meaning under high or room temperature and atmosphere pressure. We expect that this mechanism may be appropriate to be utilized to other superconducting cases and therefore, can be adapted to describe the superconducting phenomenon for other superconductors. If this superconducting mechanism can be successfully applied to other superconductive cases, it may be served as a tool for future research to bring the superconducting transition (critical) temperature T_c to exceed room temperature landmark and hence, the over a century dream of obtaining an applicable superconductor can be realized.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

Food and Agricultural Organisation estimates from 2014 suggest 64% of the high seas migratory stocks are either overfished or undergoing overfishing. Illegal fishing exacerbates the damage to marine ecosystems, human rights, and food security, and is yet to be included in the recent United Nations (UN) draft agreement to protect high seas biodiversity. We used catch data from the Sea Around Us Project to determine trends in fishing gear use and the catches of countries fishing in the high seas. Using Two-way ANOVA, Principal Coordinates Analysis, and SIMPER Test, we found that Spain, Taiwan, Japan, Indonesia, and Ecuador had the highest catches in 2004-2014. Each decade, only 1 in 10 countries (10.8%) caught over 500,000 tonnes, leaving the remaining 90% of countries catching less than 500,000 tonnes. Further analysis showed the mean high seas catch per fishery decreased 55% between the 2000s and the 2010s. Purse seine and longline were increasingly used towards the 2010s. Catch from purse seine and longline accounted for 70.5% and 78.4% of total high seas catch in 1950-2014 and 2004-2014, respectively. Discards were unreported throughout 1950-2014, and the reporting levels of landings varied greatly between countries and gears. We call for immediate action and recommend (1) including international, overarching high seas governance to end illegal and unsustainable fishing in the high seas in the UN draft agreement, and (2) using large mobile marine protected areas in high seas fisheries management through the UN draft agreement.

Background and Objectives: High job strain is worsening the outcome in coronary artery disease, CAD. Severe dissatisfaction on workplace, imbalance between high demands , and low rewards, are affecting the quality of life, and diminishing the duration of life, especially in CAD patients. Our study included two samples : CAD patients (experimental group), and without CAD patients, but with traditional risk factors (control group). The main objective of the study was the role played by high sensitivity C reactive protein, hs CRP, and microalbuminuria, as mediators of job strain and CAD relationship. Secondary objectives were the following: identification of the most vulnerable patients( with significant job strain) and intervention towards this category, for cardiovascular events prevention (primary or secondary). Materials and Methods: The utilized methods were the following : clinical exam; electrocardiogram; echocardiogram; non contrast enhanced computed chest tomography; laboratory findings ( lipid profile, glycemia, hs CRP, microalbuminuria); type D scale, DS 14; depression questionnaire, PHQ-9; and satisfaction with work scale, SWWS. Results: The highest values for hs CRP and microalbuminuria were noticed in patients with the lowest Likert score, for both samples CAD, and without CAD patients. The highest job strain was noticed in females. More than half of CAD patients ,with low Likert scores, revealed myocardial infarction. Conclusions: Microalbuminuria and hs CRP were statistical significant in the study as intercessors, in job strain and CAD relationship. The most vulnerable patients for vascular events were females, in both groups : CAD and “CAD waiting desk”. In CAD sample, the vascular vulnerability was also increased by high job strain.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

The aim of the study was to compare the standard baseline imaging, with extended radiological staging. To assess our hypothesis, we performed a prospective, single-centre study which included 132 participants recruited between October 2015 and March 2020. Descriptive statistics, the Friedman and chi-squared tests were performed and p &lt; 0.05 was considered significant. Patients were grouped into two cohorts, CT scan cohort (n=87) and PET-CT cohort (n=43). In the first group the originally determined disease stage changed in 36.8 % of cases, in second group in 51.2 %. The consistency between assessment of axillary lymph nodes by imaging (cN) and the postoperative pathology report (pN) was evaluated. In most cases, clinical and pathological evaluation of involved nodes was consistent, for CT scan the result was χ2(1) = 18.98; p &lt; 0.001, for PET-CT the result was χ2(1) = 6.41; p = 0.03. Highly customized radiation therapy defined as dose boost within the involved lymph nodes, not covered by surgeon, was applied in nine patients.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

The pharmaceutical industry is undergoing a shift in processing methods for small-scale production (250-1000 kg/a), leading to an increased focus on continuous production research. Various concepts were developed to overcome challenges in small-scale crystallization for the production of high-quality products. However, further optimization is needed to enhance the industrial applicability of these concepts. This study aims to demonstrate the practical applicability of the Slug Flow Crystallizer (SFC) in the pharmaceutical industry by extending its use to a wider range of substance systems for small-scale API production. Employing an experimental strategy, the research seeks to rapidly assess the SFC's potential for achieving uniform, high-purity product yields, emphasizing the importance of factors such as slug flow stability, residence time distribution, and substance-specific crystallization criteria. This, coupled with our previously published model-based strategy, forms a comprehensive methodology to explore crystallization behavior and modeling for a variety of substance systems within the SFC. The ultimate goal of this study is to showcase the practicality of the SFC in the pharmaceutical industry, enabling the way for its reliable use in long-term, small-scale continuous crystallization and the production of high-quality pharmaceutical products.

This research investigates the fatigue crack propagation on the lower surface of rocket deflector troughs of offshore rocket launch platforms. Initially, a numerical model of the offshore rocket launch platform is established using ABAQUS based on the Extended Finite Element Method (XFEM). Subsequently, two variable parameters—namely, the initial crack length and initial tilt angle—are introduced. This research systematically analyzes the impact of these parameters on fatigue crack propagation patterns in both the maximum stress and maximum deformation regions of the deflector channels under the combined conditions of high temperature and impact. Finally, the research indicates that the propagation length of surface cracks in the deflector trough exhibits a trend of initial increase followed by a subsequent decrease with the increase in the preset inclination angle. Notably, the stable propagation rate of the crack in the region of maximum deformation surpasses that observed in the region of maximum stress. Through meticulous comparative analysis, it is evident that temperature loading significantly fosters the initiation and propagation of cracks, particularly in the upper region of the deflector channel's lower surface.

Understanding that organizational communication is crucial for the consistent functioning of any establishment, this research assesses its influence on work-life balance, organizational climate, and job satisfaction among Portuguese firefighters, a rarely studied group. Effective organizational communication is identified as a potential pathway for nurturing a favorable work setting and bolstering employee contentment, essential elements of work-life balance. Data compiled from a group of 102 firefighters, using a sociodemographic questionnaire, the Work Social Climate Scale, and Portuguese versions of the ICA Communication Audit Survey Instrument and the Labor Satisfaction Questionnaire S20/23, unveil multiple significant correlations among various dimensions of the ICA, the Work Social Climate Scale, and communication metrics. Explicitly, correlations were discerned between received and sent communications and aspects of implication, support, and cohesion. Links were also evident between desired communications and the control dimension. Positive and statistically significant relationships were further observed between received and sent communications, all five satisfaction dimensions, necessary outgoing communications and the physical environment, and required outgoing communications and benefits, highlighting the pivotal role of adept communication in augmenting work-life balance, organizational climate, and job satisfaction among firefighters.

High-methoxyl apple pectin (AP) derived from apple was employed as the main ingredient facilitating rheological modification features for developing dysphagia-friendly fluidized alimentary matrices. Xanthan gum (XG) was also included as a composite counterpart to modify the viscoelastic properties of the thickened system under different thermal processes. The results indicate that AP is extremely sensitive to thermal processing, and the viscosity is greatly depleted under a neutral pH level. Moreover, the inclusion of calcium ions echoed a modification effect on the rheological properties of AP, and both the elastic property and viscosity value are promoted after thermal processing. The modification effect of viscoelastic properties (Gʹ and Gʹʹ) is observed while XG is incorporated into the composite formula. By promoting the XG ratio from 7: 3 to 6: 4 (AP: XG), it triggers the rheological transformation from a liquid-like form to a solid-like state, and the viscosity value shows that the AP-XG composite system exhibits better thermal stability after thermal processing. The ambient modifiers of pH (pH &lt; 4) and calcium chloride concentration (7.5%) with an optimal AP-XG ratio of 7:3 lead to weak-gel-like behavior (Gʹʹ &lt; Gʹ), helping to maintain the texture properties of dysphagia-friendly features similar to those prior to the thermal processing.

Abstract: CRISPR/Cas systems are used for genome editing, both in basic science and in bio-technology. At the same time, CRISPR/Cas editors have several limitations, including insufficient specificity leading to "off-targets" and the dependence of activity on chromatin state. A number of highly specific Cas9 variants have been obtained now, but most of them are characterized by reduced activity on eukaryotic chromatin. We identified a spatial cluster of amino acid residues in the PAM-recognizing domain of Streptococcus pyogenes Cas9, whose mutations restore the activity of one of the highly specific forms of SpyCas9 without reducing its activity in Saccharomyces cere-visiae. In addition, one of these new mutations also increases the efficiency of SpyCas9-mediated editing of a site localized on the stable nucleosome. The improved Cas9 variants we obtained, which are capable of editing hard-to-reach regions of the yeast genome, may help in both basic research and yeast biotechnological applications.

Gas turbine engines are widely used in various industries such as aviation, power generation, and marine propulsion due to their high efficiency and reliability. The combustion chamber of a gas turbine engine design contains a number of elements, including as the chamber's size and form, the fuel injection system, the ignition system, and the cooling system and it plays a critical role in the performance and efficiency of the engine. This research discusses the fabrication of a combustion chamber model for a gas turbine engine. The aim of this research is to develop a combustion chamber that is cost-effective, easily available, and can be fabricated in less time. The research covers the different types of combustion chambers used in gas turbine engines and compares their advantages and disadvantages. It then selects the best type of combustion chamber for the gas turbine engine based on its cost, availability, and fabrication time, Efficiency and high power to fuel ratio. The report also describes the fabrication process involved, including the techniques and materials used, along with safety precautions and environmental protection measures. Lastly, the research suggests future improvements and potential applications for the fabricated combustion chamber model.

Cross-sectional survey was conducted to capture the true extent of COVID-19 exposure among students and staff of Polytechnic High School (PHS). Random cluster sampling was carried out between May 19 and August 18, 2022, after the fourth wave of COVID-19 transmission. IgM and IgG SARS-CoV-2 antibodies were screened using WANTAI SARS-CoV-2 ELISA assays. Seroprevalence and descriptive statistics were calculated. Moreo-ver, the association between seropositivity and different factors (age, gender, preventive measures comorbidity, and symptoms, etc.) was determined using Logistic Regression. The overall IgG and IgM seroprevalence were 92% and 6.91% respectively. We found a higher IgM seroprevalence in men than women (9.4% vs. 5.6%) and a lower IgM seroprevalence in (18-25) age group compared to (55-65) years. Low compliance with preventive measures was found with a significant IgM seroprevalence depending on non-respect of social distancing (p = 0.008). A total of 70% of participants presented symptoms linked to COVID-19 at the moment of the survey. Results revealed a significant difference according to IgG seroprevalence among participants who declared fa-tigue symptoms 92.06% compared to those who did not 80.39% (p = 0.0027). IgM seropositivity was associated with Body Mass Indice (BMI) categorized (O.R. 0.238, p = 0.043), ethnic group (O.R. 0.723, p = 0.046) and marital status (O.R. 2.399, p = 0.021). Moreover, IgG seropositivity was associated with Chronic sinusitis comorbidity (O.R. 0.238, p = 0.043) and vaccination status (O.R. 4.741, p < 0.001). The majority of students and staff have al-ready been exposed to SARS-CoV-2 and confirm the circulation of SARS-CoV-2 in PHS at the time of the survey. Our results underline the importance of sero-epidemiological surveys to estimate the real impact of the COVID-19 pandemic in a community and to monitor disparities in antibody response in the population.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Numerous studies were published suggesting that troponin level is related to adverse outcomes in chronic cardiac and non-cardiac conditions. Our study investigated whether troponin levels gathered from an unselected blood sample taken during outpatient care are associated with adverse outcomes in a population with stable coronary artery disease. In a cohort of 949 patients with stable coronary artery disease, average age of 67.5 ± 9.5 years, 69.5% male, 52.1% diabetics, 51.6% with previous myocardial infarction, 57.9% with triple-vessel disease, 21.7% of patients encountered new events during an average period of monitoring of 2.07 ± 0.81 years. Troponin I/99th percentile categorized into tertiles emerged as an independent predictor of death and combined events risk (hazard ratio: 2.02 (1.13-3.60), p=0.017; 2.30 (1.37-3.88, p=0.002, respectively). A troponin ratio > 0.24 was able to identify 53.3% of patients at risk of death and heart failure hospitalization. In patients with stable coronary artery disease and adherent to treatment, troponin level is independently associated with death and heart failure hospitalization in a medium-term follow up.

Oscillations in global modes of variability (MoV) form global teleconnections that affect regional climate variability and modify the potential for severe and damaging weather conditions. Understanding the link between certain MoVs and regional climate can improve the ability to more accurately predict environmental conditions that impact human life and health. In this study, we explore the connection between different MoVs, including the Arctic Oscillation (AO), Eurasian teleconnection, Indian Ocean Dipole (IOD), North Atlantic Oscillation (NAO), and El Niño Southern Oscillation (Nino34), with winter and summer climate in the High Mountain Asia (HMA) region, including geopotential height at 250 hPa (z250), 2-m air temperature (T2M), total precipitation (PRECTOT), and fractional snow cover area (fSCA). Relationships are explored for the same monthly period between the MoVs and the climate variables, but also using a lagged correlation analysis to investigate whether any relationship exists at different time lags. We find that T2M has a negative correlation with the Eurasian teleconnection in the Inner Tibetan Plateau and Central China in both winter and summer and a positive correlation in Western China in summer. PRECTOT has a positive correlation with all MoV in most regions in winter, especially with the IOD, and a negative correlation in summer, especially with the Eurasian teleconnection. Snow cover in winter is positively correlated with most indices throughout many regions in HMA, likely due to wintertime precipitation also being positively correlated with most indices. Generally, the AO and NAO show similar correlation patterns with all climate variables, especially in the winter, possibly due to their oscillations being so similar. Furthermore, the AO and NAO are shown to be less significant in explaining the variation in HMA climate compared to other MoVs such as the Eurasian teleconnection. Overall, our results pinpoint different time-windows and specific regions within HMA that exhibit high correlation between climate and MoVs, which might offer additional predictability of the MoVs as well as of climate and weather patterns in HMA and throughout the globe.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double &lt;100&gt; and &lt;111&gt; fiber and a unique component of (001)&lt;110&gt;, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

The antioxidant and anti-inflammatory abilities of beeswax alcohol (BWA) are well reported in animal and human clinical studies, with a significant decrease in malondialdehyde (MDA) in blood, reduction of liver steatosis, and decrease in insulin. On the other hand, there is insufficient information to explain the in vitro antioxidant activity of BWA because it is extremely insoluble in aqueous buffer system. The BWA mixture was incorporated into reconstituted HDL (rHDL) with apoA-I, and the physiological functions of BWA in a water system were evaluated. After synthesis of rHDL with palmitoyloleoyl phosphatidylcholine (POPC), cholesterol, apolipoprotein A-I (apoA-I), and the BWA at molar ratios of 95:5:1:0 (rHDL-0), 95:5:1:0.5 (rHDL-0.5), and 95:5:1:1 (rHDL-1) for POPC:FC:apoA-I:BWA, the particle size of rHDL-1 was increased 15% compared to rHDL-0. rHDL-1 exhibited the strongest anti-glycation activity, up to 18% less glycation than rHDL-0 treated HDL3, with the highest protection of apoA-I from proteolytic degradation: a 28% larger band intensity than that of rHDL-0 treated HDL3 in the presence of fructose (final 250 mM). The antioxidant ability to inhibit cupric ion-mediated LDL oxidation increased as the BWA content in rHDL increased. The rHDL-1-treated LDL exhibited the smallest oxidation extent in electromobility with the least quantification of oxidized species (MDA). The antioxidant activities of HDL, ferric ion reduction ability (FRA), and paraoxonase (PON) were enhanced by the BWA in rHDL treatment with a concomitant increase in the molar ratio. rHDL-1-treated HDL showed 20–22% higher FRA and PON activities than rHDL-0-treated HDL. A microinjection of each rHDL into zebrafish embryos was performed in the presence of carboxymethyllysine (CML). The rHDL-1 injected embryo exhibited the highest survivability (~63%), whereas the CML alone group showed 28% survivability. A higher BWA content in rHDL helped neutralize the CML toxicity, resulting in higher survivability and normal developmental morphology. In contrast, the CML alone injected embryo showed severe retardation of the developmental speed and morphological defect. The CML-alone group showed the highest extent of reactive oxygen species (ROS) production and cellular apoptosis in embryos, but a co-injection of rHDL-1 resulted in a remarkable decrease in ROS and apoptosis. The dermal application of rHDL containing BWA resulted in higher potent wound-healing activity in a dose-dependent manner with decreased reactive oxygen species and cellular apoptosis in the cutaneous wound area in the presence of CML. Conclusively, incorporating BWA in rHDL significantly enhanced the anti-glycation and antioxidant activities in rHDL via more stabilization of apoA-I with a larger particle size. The rHDL containing BWA facilitated enforced inherent antioxidant ability of HDL and anti-inflammatory activity to suppress the CML toxicities in zebrafish embryos and to ameliorate CML-aggravated chronic wounds in adult zebrafish.

We present a mixing length based algebraic turbulence model calibrated to pipe flow; the main purpose of the model is to capture the increasing turbulence production-to-dissipation ratio observed in connection with the high Reynolds number transition region. The model includes the mixing length description by Gersten and Herwig which takes the observed variation of the von Kármán number with Reynolds number into account. Pipe wall roughness effects are included in the model. Results are presented for area-averaged (integral) quantities which can be used both as a self-contained model and as initial inlet boundary conditions for computational fluid dynamics simulations.

We study the influence of high-order twisting phases on polarization states and optical angular momentum of a vector light field with locally linear polarization and a hybrid state of polarization (SoP). The initial SoP of a twisted vector optical field (TVOF) modulated by the high-order twisting phase possesses various symmetric distributions. The propagating properties of a high-order TVOF with locally linear polarization and hybrid SoP are explored, including the intensity compression, expansion, and conversion between the linear and circular polarization components. In particular, orbital angular momentum (OAM) appears in a high-order TVOF during propagation where no OAM exists in the initial field. The variation of OAM distribution in cross-section becomes more frequent with the increase of the twisting phase order. In addition, a non-symmetric OAM distribution appears in an anisotropic TVOF, leading to the rotation of the beam around the propagation axis during propagation. These results provide a new approach for optical field manipulation in a high-order TVOF.

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

The G-NUMEN array is the future gamma spectrometer of the NUMEN experiment (Nuclear Matrix Element for the Neutrinoless double beta decay), to be installed around the object point of the MAGNEX magnetic spectrometer at the INFN-LNS laboratory.. This project aims at exploring Double Charge Exchange (DCE) reactions in order to obtain crucial information about the neutrinoless double beta decay (0νββ). The primary objective of the G-NUMEN array is to detect the gamma rays emitted from the de-excitation of the excited states populated via DCE reactions with good energy resolution and detection efficiency, amidst a background composed of transitions from competingreaction channels with far higher cross-sections. To achieve this, the G-NUMEN signalswill be processed in coincidence with those generated by the detection of the reaction ejectiles in the MAGNEX Focal Plane Detector(FPD). Under the expected experimental conditions, G-NUMEN detectors will operate at high counting rates, of the order of hundreds of kHz per detector, while maintaining excellent energy and timing resolutions. The complete array will consist of over 100 LaBr3(Ce) scintillators. Initial tests have been conducted on the first detectors of the array, allowing for the determination of their performance at high rates.

Biomass-derived carbon dots (CDs) are gaining much interest in recent times as it is a sustainable option with abundant availability, low cost, and tunable luminescence. Herein, we report a simple green synthesis method to produce highly fluorescent CDs from Eucalyptus globulus leaves using the one-pot hydrothermal approach. The fabricated CDs exhibit strong blue fluorescence with an excitation and emission maxima of 340 nm and 442 nm respectively. The highest quantum yield (QY) obtained was 60.7%. Due to its promising optical properties and biocompatibility, CDs can be a potential candidate for biosensing applications. Moreover, we employed a life cycle assessment (LCA) cradle-to-gate approach to study the environmental impacts of the synthesis strategy used for the fabrication of CDs. The results point out that citric acid is a main hotspot in CDs synthesis, regarding environmental impacts in most categories. This justifies the introduction of biomass, which reduces the amount of citric acid, thus leading to a more sustainable synthesis strategy for fabricating CDs.

With the rapid development of the economy and the transformation of social contradictions, the economic development model in China has also changed, and a high-quality economic development model has been proposed. This paper uses the entropy method to measure the level of innovation and high-quality economic development in nine prefecture-level cities in Fujian Province from 2011 to 2020, and finds that the overall level shows an increasing trend year by year, but there are obvious regional differences. By constructing a grey correlation degree model, it is found that the innovation subsystem and the high-quality economic development are strongly correlated, the development level of innovation and the subsystem of high-quality economic development are both strongly correlated, the grey correlation degree from high to low is green, coordinated, shared, and livelihood, indicating that innovation has a significant impact on high-quality economic development. Based on the research results, countermeasures and suggestions are proposed to promote the coordinated development of innovation and high-quality economy.

Creep is a fundamental property naturally exists in some types of rock, which is significant for the long-term stability of roadways during the mining process. In this paper, the long-term strength of coal and rock were obtained via laboratory experiments, and a Cvisc elasto-viscoplastic model was adopted and introduced in FLAC3D, based on the 3101 transport roadway in Hongqinghe Coal Mine, to investigate the influence of creep on the stability of deep-high stress roadway. The test results show that the long-term strength of 3-1 coal and sandy mudstone, respectively, is 18.65 MPa, 39.95 MPa. The plastic zone, the deformation, and the damage of roadway surrounding rock behave an obvious increase after being excavated for 720d as the creep model was chosen. The plastic zone failure with models shear-p (1090.7 m3), shear-n (381.7 m3), tension-n (98.4 m3), and tension-p (30.8 m3), the damage value has an obvious increment of increased 21.2% (0.053), the deformation increases in the order is two-sidewalls (1978 mm), roof (907 mm), floor (101 mm). The creep of the roadway can be divided into three stages: the accelerating stage, the decaying stage, and the stable stage. The creep speed of each stage is greatly affected by the presence or absence of anchor spray support: the creep speed of the bare roadway roof, roadway side, and floor stability, respectively, is 1.01, 1.02, and 0.12 mm/d; After anchor spray support, the creep velocity, correspondingly, decreased to 0.69, 0.37, and 0.12 mm/d, and the amount of surrounding rock damage decreased from 0.302 to 0.243. This indicates that the anchor spray support can significantly reduce the creep effect of the roadway. The Cvisc creep model was verified reliable and can provide guidance for deep high-stress coal roadway support.

High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

The generation of eucalypt sawdust has increased in Uruguay with the expansion of pulp and paper industrial sites. Currently, most of this readily available feedstock is either not used or applied for producing heat and power by combustion in biomass boilers. In this work, eucalypt sawdust was subjected to steam explosion as the first step for cellulosic ethanol production within the biorefinery concept. The effect of sawdust moisture content, pretreatment temperature and residence time were evaluated, along with the influence of water washing of steam-exploded solids on enzymatic hydrolysis and fermentation yields. After steam explosion, 60% xylans and 97% acetyl groups were recovered mainly as oligomers and acetic acid in the pretreatment liquor. Eucalypt sawdust moisture content affected the enzymatic hydrolysis performance and glucan conversion efficiency. Water washing after pretreatment improved hydrolysis efficiencies and ethanol production yields by 10% with respect to the unwashed pretreated solids at the same experimental condition. The best ethanol yields were obtained using PSSF (pre-saccharification and simultaneous saccharification and fermentation) after pretreatment at 205°C for 10 min, using sawdust with an 8% moisture content. In this case, 227 L ethanol and 40 kg total xylose (including xylo-oligomers) were obtained per ton of dry eucalypt sawdust.

The structural stability of γ-boron is investigated using Raman spectra under high pressures up to 126 GPa at ambient temperature. The pressure dependence of all the Raman-active modes of the γ-boron is reported. We also observe amusing changes within the B3g and B1g Raman-active vibrational modes, which results in the phenomenon of merging first and then separating of the Raman peaks. In addition to the Raman measurements, the changes in crystal structure and force constants are calculated to reasonably explain the discrepancy between the two Raman modes in response to pressure. The results of the continuous shifts for all Raman modes with increasing pressure indicate that γ-boron remains stable below this pressure value, with no changes in either symmetry or structure.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

The functions of annexin A1 (ANXA1) that is expressed on membranes and in cytoplasmic granules have been fully described. Nonetheless, the role of this protein in protecting against DNA damage in the nucleus is still emerging and requires further investigation. Here, we investigated the involvement of ANXA1 in DNA damage response in placental cells. Placenta was collected from ANXA1 knockout mice (AnxA1-/-) and pregnant women with gestational diabetes mellitus (GDM). The placental morphology and ANXA1 expression, which are related to the modulation of cellular response markers in the presence of DNA damage, were analyzed. Total area of AnxA1-/- placenta was smaller because of reduced labyrinth zone, enhanced DNA damage, and impaired base excision repair (BER) enzymes, which resulted in the induction of apoptosis in the labyrinthine and junctional layers. The placentas from pregnant women with GDM showed reduced expression of AnxA1 in the villous compartment, increased DNA damage, apoptosis, and reduction of enzymes involved in the BER pathway. Our translational data provide valuable insights into the possible involvement of ANXA1 in the response of placental cells to oxidative DNA damage and represent advancement in investigations on the mechanisms involved in placental biology.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

Abstract: Pomegranate peels are important source of polyphenols with remarkable interest in food, pharmaceutical and cosmetic industry. An improved extraction of total polyphenolic com-pounds (TPC) from pomegranate peels by Solid-State Fermentation (SSF) was achieved. A Box Hunter & Hunter (BHH) followed by Central Composite Design (CCD) were performed to assess the effect of the process variables on TPC release. The statistic designs indicate that the best TPC extraction (234.85 mg GAE/gdm) by means of SSF occurs, at 42°C, 50 % moisture, pH 5.0, mineral solution (g/L): NaNO3 (3.83), KH2PO4 (1.52), MgSO4 (4.66) and KCl (1.52) at 36 h. At the best fer-mentation conditions, TPC (248.78±1.24 mgGAE/gdm) increased 5.96-fold than values previously reported and antioxidant activity [AA] increased 5.81-fold than the value obtained before the SSF optimization. High-valued citric acid, α and β punicalin, α and β punicalagin, punigluconin, gal-loyl-HHDP hexoside and ellagic acid molecules were identified. The increased extraction of TPC by SSF provides a suitable alternative for pomegranate peels valorization through the re-covery of molecules with high added value with potential use in food, pharmacy and cosmetic industries; a diversification in the use of food agroindustry by-products is obtained as approach to the circular economy model through biotechnological processes.

With the aim to improve cladding coating quality and prevent cracking, this paper established an extreme high-speed laser cladding thermo-mechanical coupling simulation model to study the evolution of the temperature field and residual stress distribution. Process parameters that impacted the macroscopic morphology of single-pass coatings were investigated. Numerical calculations and temperature field simulations were performed based on the process parameter data to validate the effect of the temperature gradient and cooling rate on the coating structure and the residual stress distribution. The results showed that a good coating quality could be achieved using a laser power of 2400 W, a cladding rate of 20 m/min, and a powder feeding rate of 20.32 g/min. The coatings’ cross-sectional morphology corresponded well with the temperature distribution predicted by numerical modeling of the melt pool. The microstructure of the molten coatings is affected by the temperature gradient and cooling rate, which vary greatly from the bottom to the middle to the top. Maximum residual stress appears between the bonding region of the coatings and the substrate, and the coatings themselves have significant residual stress in the form of tensile strains that are mostly distributed in the direction of the laser cladding speed.

This paper analyzed the main diseases of the friction high-strength bolt (FHSB) joints in order to study the characteristics of the corrosion products of the joints in steel bridge and the influence factors. Seven representative FHSB connection pairs and eight steel plate samples were selected from the Dongying Shengli Yellow River Bridge, which has been in operation for 33 years. Then Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD) were used to analyze the microscopic morphology and chemical composition of the corroded surface of the samples. Finally, this paper discussed the relationship between the corroded sample surface and the environmental corrosion. The research results showed that construction quality problems, such as non-standard hole expansion, segmental slab joint dislocation and contact surface pollution, accelerated corrosion of the contact surface. With the increase of corrosion degree of joints, the contact surface of aluminum spraying layer gradually changed from a rugged and dense state to a smooth and porous powder state. With the corrosion of the steel plate substrate, the contact surface gradually changed from a fluffy stratified state to a surface bonding state. It was inferred that the friction coefficient of the FHSB connection node on the corroded aluminum sprayed contact surface first decreased and then increased. The corroded node samples detected not only a large number of S and Cl elements, but also the oxides of Mn, Si and other elements as well as FeS. It was speculated that node corrosion was also related to atmospheric (acid rain) and industrial dust and other corrosive environments. Almost all samples detected the component SiO2 of the Yellow River soil, as well as Mg, Ca, K, Na and other elements at the same time, which is basically consistent with the component elements of the Yellow River soil. Therefore, it was inferred that it was related to the inclusion of the Yellow River soil.

Purpose: This study investigates the impact of different intensity normalization (IN) methods on the overall survival (OS) radiomics models’ performance of MR sequences in primary (pHGG) and recurrent high-grade glioma (rHGG). Methods: MR scans acquired before radiotherapy were retrieved from two independent cohorts (rHGG C1: 197, pHGG C2: 141) from multiple scanners (15, 14). The sequences are T1 weighted (w), contrast-enhanced T1w (T1wce), T2w, and T2w-FLAIR. Sequence-specific significant features (SF) associated with OS, extracted from the tumour volume, were derived after applying 15 different IN methods. Survival analyses were conducted using Cox proportional hazard (CPH) and Poisson regression (POI) models. A ranking score was assigned based on the 10-fold cross-validated (CV) concordance index (C-I), mean square error (MSE), and the Akaike information criterion (AICs), to evaluate the methods’ performance. Results: Scatter plots of the 10-CV C-I and MSE against the AIC showed an impact on the survival predictions between the IN methods and MR sequences (C1/C2 C-I range: 0.62-0.71/0.61-0.72, MSE range: 0.20-0.42/0.13-0.22). White stripe showed stable results for T1wce (C1/C2 C-I: 0.71/0.65, MSE: 0.21/0.14). Combat (0.68/0.62, 0.22/0.15) and histogram matching (HM, 0.67/0.64, 0.22/0.15) showed consistent prediction results for T2w models. They were also the top-performing methods for T1w in C2 (Combat: 0.67, 0.13; HM: 0.67, 0.13), however, only HM achieved high predictions in C1 (0.66, 0.22). After eliminating IN impacted SF using Spearman’s rank-order correlation coefficient, a mean decrease in the C-I and MSE of 0.05 and 0.03 was observed in all four sequences. Conclusion: The IN method impacted the predictive power of survival models. Thus, performance is sequence-dependent.

Evolutionary ecology may be described as explaining ecology through evolution and vice versa, but one may also view it as an integration of the two fields, where one takes the view that ecology and evolution are inseparable, and one can only begin to understand the biology of organisms by synthesizing the two fields. An example of such a synthesis is the biology of high fecundity and the associated concept of sweepstakes reproduction, or skewed individual recruitment success. As an illustration we consider selection at linked sites under various dominance and epistasis mechanisms in a diploid population evolving according to random sweepstakes and experiencing recurrent bottlenecks. Using simulations we give a few examples of the impact of the stated elements on selection. We show that depending on the dominance mechanisms random sweepstakes can shorten the time to fixation (conditional on fixation) of the fit type at all sites. Bottlenecks tend to increase the fixation time, with random sweepstakes counteracting the effects of bottlenecks on the fixation time. Understanding the effect of random sweepstakes, recurrent bottlenecks, dominance mechanisms and epistasis on the fate of selectively advantageous mutations may help with explaining genetic diversity in natural highly fecund populations possibly evolving under sweepstakes reproduction.

The turbulent Poiseuille flow between two parallel plates is one of the simplest possible physical situations, and it has been studied intensively. In this paper, we propose a modified Prandtl-van Driest mixing length that satisfies both boundary conditions and wall damping effects. With our new formulations, we numerically solve the problem and, moreover, propose an approximate analytical solution of mean velocity. As applications of our solution, an approximate analytical friction coefficient of turbulent Poiseuille flow is proposed.

Background: Some patients who have recovered from COVID-19 have experienced a range of persistent symptoms or the appearance of new ones after a SARS-CoV-2 infection. These symptoms can last from weeks to months, impacting everyday functioning to a significant number of patients. Methods: A cross-sectional analysis based on an online, self-reporting questionnaire was conducted in Ecuador from April to July 2022. Participants were invited by social media, radio, and TV to voluntarily participate in our study. A total of 2103 surveys were included in this study. We compared socio-demographic variables and long-term persisting symptoms at low (&lt; 2,500 m) and high altitude (&gt;2,500 m).Results: Overall, 1100 (52.3%) responders claimed to have long-term symptoms after SARS-CoV-2 infection. Most of these symptoms were reported by women (64.0%), the most affected group was young adults (68.5%), and the majority of long-haulers were mestizos (91.6%). We found that high altitude residents were more likely to report persisting symptoms (71.7%) versus those living at lower altitudes (29.3%). The most common symptoms were fatigue or tiredness (8.4%), hair loss (5.1%) and difficulty concentrating (5.0%). The highest proportion of persisting symptoms was observed among those who received an incomplete vaccine scheme.Conclusions: This is the first study describing post-COVID symptoms' persistence in low and high-altitude residents. Our findings demonstrate that women, especially those aging between 20-40, are more likely to describe sequalae associated with post-COVID. We also found that living at a high altitude was associated with earlier onset and longer symptom duration. Finally, we found a greater risk to report long lasting symptoms among women, those with previous comorbidities and those who had a severer acute SARS-CoV-2 infection.

Mixture of abramis brama (freshwater bream), carassius carassius (crucian carp), and sander lucioperca (pike perch) scales was used for the preparation of fish scale powder containing about 26.5 wt. % of removed when heating components preferably of organic nature, and 63.5 wt. % of mineral components. Fish scale powder enriched with inorganic components was prepared from washed, dried, and ground fish scale mixture using vibration sieving. Inorganic powders consisting of hydroxyapatite and magnesium whitlockite were obtained via heat treatment of this fish scale powder at 800-1000 oC. Particles of these inorganic powders consisted of sintered grains with dimensions less than 100 nm after heat treatment at 800 oC, less than 200 nm after heat treatment at 900 oC, and 100-500 nm after heat treatment at 1000 oC. Fish scale powder enriched with inorganic components as well as heat-treated inorganic powders consisting of hydroxyapatite and magnesium whitlockite can be recommended for the production of different materials such as ceramics or composites.

In the diagnosis of olfactory neuroblastoma (ONB), the presence of S-100–positive sustentacular cells surrounding the tumor is important; however, these are also present in normal nasal sinus epithelium. Although ONB often has a different final diagnosis, complete resection of the tumor has a good prognosis and minimally affects the patient's treatment plan. When the tumor extends around the internal carotid artery (ICA), complete resection is difficult due to the high risk of vascular injury; revascularization using a high-flow bypass can avoid this complication. In the present case, the tumor was located in the left sphenoid sinus and extended around the ICA. Preoperative biopsy tissue was positive for neuroendocrine markers and slightly positive for S-100 protein, leading to a diagnosis of ectopic ONB. High-flow bypass revascularization with trapping of the ICA allowed complete tumor resection. The postoperative histopathological diagnosis was neuroendocrine carcinoma, showing no S-100 protein–positive cells. There was no sign of recurrence two and a half years after surgery without additional treatment. This case demonstrates that the presence of S-100 protein–positive cells in ONB may be misleading. Although misdiagnosis of ectopic ONB should be anticipated, a complete resection of the tumor is an effective treatment strategy.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

Phenotypic characterization of crop genotypes is an essential yet challenging aspect of crop management and agriculture research. Digital sensing technologies are rapidly advancing plant phenotyping and speeding-up crop breeding outcomes. However, off-the-shelf sensors might not be fully applicable and suitable for agriculture research due to diversity in crop species and specific needs during plant breeding selections. Customized sensing systems with specialized sensor hardware and software architecture provide a powerful and low-cost solution. This study designed and developed a fully integrated Raspberry Pi-based LiDAR sensor named CropBioMass (CBM), enabled by internet of things to provide a complete end-to-end pipeline. The CBM is a low-cost sensor, provides high-throughput seamless data collection in field, small data footprint, injection of data onto the remote server, and automated data processing. Phenotypic traits of crop fresh biomass, dry biomass, and plant height estimated by CBM data had high correlation with ground truth manual measurements in wheat field trial. The CBM is readily applicable for high-throughput plant phenotyping, crop monitoring, and management for precision agricultural applications.

Capacitor banks are widely used in current electrical transmission systems in order to improve power quality and increase efficiency. Utilizing high voltage components such as, shunt capacitors in the power grid imposes new challenges to the system which are required to be addressed. One of these challenges is corona discharges that can have negative impacts on capacitor banks such as power loss, insulator erosion followed by equipment failure, and radio interference. Although previous studies have almost exclusively focused on optimization of corona suppression rings for transformers and transmission lines, no specific studies have conducted regarding high voltage capacitor banks. This paper presents a novel study concerning verification and development of corona discharge suppression models on AC and DC capacitor banks with two different voltage levels. The employed method is based on the Maxwell’s equations and finite element method (FEM) which is implemented with the help of COMSOL Multiphysics© software. Results have verified the necessity of suppression methods as well as the efficiency of proposed solutions. Corona inception voltage levels are identified and effective factors on its appearance are reviewed. Analyses of proposed solutions have shown significant improvements in optimization of corona suppression methods as well as enhancement of maintenance maneuverability.

This article discusses a transformer-free, high-efficiency DC-DC converter besides renewable energy applications. The traditional buck-boost, classic Zeta, Sepic, and Cuk converter does have the benefits of a simple design, low cost, as well as the capacity to execute voltage step-up and step-down. Conversely, because of the detrimental consequences of the parasitic constraints of the device, the voltage conversion gain of the traditional DC-DC converter is much more restricted and the efficiency is also significantly smaller, whereas this proposed converter does have a higher voltage gain and efficiency because it is used in a single power switch, resulting in reduced switching losses and voltage stress. The said converter's design is very simple, which simplifies the operation control and reduces switching and conduction losses, leading to an efficiency of 97.4 percent. This converter seems to have the same capabilities as the Zeta converter, including continuous desired output current and desired buck-boost operation. Such an article offers the operation principle and steady evaluation, as well as a comparison with other existing high step-up configurations. The proposed converter employs a fuzzy logic controller, which improves the voltage level as well as reduces the time taken to set the voltage output of a conventional PI and ANN controller, especially in comparison to the FLC controller. For deployment, Experimental Result and MATLAB/Simulink has been used, and the modeling results indicate that the proposed controller performance has improved

Biofuels have many environmental and practical benefits as a transportation fuel. They are among the best alternatives to fossil fuels due to their capacity for negative carbon emissions, which is vital for archiving the global ambition of a Net-Zero Economy. However, conventional biofuel production takes place on inland sites and relies on freshwater and edible crops (or land suitable for edible crop production), which has led to the food vs fuel debate. It also suffers technical and economical barriers due to the energy balance and the cost of production compared to fossil fuels. Establishing a coastal integrated marine biorefinery (CIMB) system for the simultaneous production of biofuels, high-value chemicals, and other co-products could be the ultimate solution. The proposed system is based on coastal sites and relies on marine resources including seawater, marine biomass (seaweed) and marine microorganisms (marine yeasts and marine microalgae). The system will not require the use of arable land and freshwater in any part of the production chain and will be linked to offshore renewable energy sources to increase its economic and environmental value. This article aims to introduce the CIMB system as a potential vehicle for addressing global warming and speeding the global effort on climate change mitigation as well as increasing global water, food and energy security. I hope this perspective may serve to draw attention into research funding for this approach.

Background: Patients with severe chronic kidney disease (CKD G4-G5) often have chronically elevated high-sensitivity cardiac troponin T (hs-cTnT) values above the 99th percentile of the upper reference limit. In these patients, optimal cutoff levels for diagnosing non-ST-elevation acute cor-onary syndrome (NSTE-ACS) requiring revascularization remain undefined. Methods: Of 11,912 patients undergoing coronary angiography from 2012 to 2017 for suspected NSTE-ACS, 325 (3%) had severe CKD. Of these, 290 with available serial hs-cTnT measurements were included and 300 matched patients with normal renal function were selected as a control cohort. Results: Diagnostic performance for patients with severe CKD was high at presentation and similar to that of the control population (AUC, 95% CI: 0.81, 0.75-0.87 versus 0.85, 0.80-0.89, p=0.68) and the ROC-derived cutoff value at presentation was 4 times higher compared to the conventional 99th percentile. Combining the ROC-derived cutoff levels for hs-cTnT at presentation and absolute 3-hour changes, sensitivity increased to 98%, PPV and NPV improved up to 93% and 86%, re-spectively. (4) Conclusions: In patients with severe CKD and suspected ACS the diagnostic accu-racy of hs-cTnT for the diagnosis of NSTE-ACS requiring revascularization is improved by using higher assay specific cutoff levels combined with early absolute changes.

Growth benefits of high speed rail (HSR) for enterprises are not automatic, but require a buoyant local economy and a robust strategy. Against above background, main objectives of ex-ante case study have been to investigate local socio-economic and spatial impacts of proposed HSR project around Ahmedabad station area on Mumbai-Ahmedabad HSR corridor, analyze the opportunities and challenges of HSR development and draw policy implications. Qualitative research methodology has been used to elicit the perceptions and perspectives of randomly selected 43 small, medium and large enterprises. Data has been analyzed using descriptive statistics. The study reveals that HSR induced greater human interaction will activate local economy, improve business efficiency and generate employment. Frequent travels on business trips can influence enterprises decision to settle near HSR station for easy access and likely to promote realty development. The proposed HSR project should be developed in synergy with urban dynamics of cities in transition and metropolitan service cities. Poor public transport connectivity is likely to be a major challenge in improving HSR accessibility and enhancing overall impacts of HSR, which can be improved by developing an integrated urban transport system, for which cooperation of all stakeholders and coherence with firms’ strategies is essential.

This paper presents two designs of high-efficiency polarizer reflectarray antennas able to generate a collimated beam in dual-circular polarization using a linearly polarized feed, with application to high-gain antennas for data transmission links from a Cubesat. First, an 18 cm x 18 cm polarizer reflectarray operating in the 17.2 - 22.7 GHz band has been designed, fabricated and tested. The measurements of the prototype show an aperture efficiency of 52.7% for right-handed circular polarization (RHCP) and 57.3% for left-handed circular polarization (LHCP), both values higher than those previously reported in related works. Then, a dual-band polarizer reflectarray is presented for the first time, which operates in dual-CP in the frequency bands of 20 and 30 GHz. The proposed antenna technology enables a reduction of the complexity and cost of the feed chain to operate in dual-CP, as a linear-to-circular polarizer is no longer required. This property, combined with the lightweight, flat profile and low fabrication cost of printed reflectarrays, makes the proposed antennas good candidates for Cubesat applications.

This review highlights normal and tumor tissue vasculature, immunological changes, and phenotypic alterations (VIP model) as fundamental in abscopal interaction. In the stereotactic body radiotherapy (SBRT) and immunotherapy era, we are moving toward “immunological radiation planning,” i.e., radiation scheduling with abscopal effect as a vital endpoint as well. Towards this end, this manuscript presents specific diagrammatic tumor models to optimize the outcome of abscopal response in SBRT, based on the principle of the four R’s - Repair, Redistribution, Repopulation, and Reoxygenation of radiotherapy. The article highlights the importance of restricting the dose of SBRT to < 10 Gy per fraction, appropriate use of dose painting, and concomitant/delayed SBRT boost potential. Current literature indicates that immunotherapy should not precede but follow SBRT within seven days. Included is the review of integrating “cyclical” antiangiogenics, immune adjuvants/immune-metabolites as abscopal effect enhancers with SBRT. The importance of proton, carbon-ion SBRT is dealt with briefly. Proposed six fundamental requirements for augmentation of the abscopal cascade are listed. The existing exploratory results need to develop a definitive strategy amidst complex interactions in SBRT, immunotherapy, immune-adjuvants, & abscopal effects. We now have enough literature evidence to convert “abscopal by chance” to “abscopal by design” by harmonized combinatorial approach.

We propose a chemical language processing model to predict polymers’ glass transition temperature (Tg) through a polymer language (SMILES, Simplified Molecular Input Line Entry System) embedding and recurrent neural network. This model only receives the SMILES strings of polymer’s repeat units as inputs and considers the SMILES strings as sequential data at the character level. Using this method, there is no need to calculate any additional molecular descriptors or fingerprints of polymers, and thereby, being very computationally efficient and simple. More importantly, it avoids the difficulties to generate molecular descriptors for repeat units containing polymerization point `*’. Results show that the trained model demonstrates reasonable prediction accuracy on unseen polymer’s Tg. Besides, this model is further applied for high-throughput screening on an unlabeled polymer database to identify high-temperature polymers that are desired for applications in extreme environments. Our work demonstrates that the SMILES strings of polymer’s repeat units can be used as an effective feature representation to develop a chemical language processing model for predictions of Tg. The framework of this model is general and can be used to construct structure-property relationships for other polymer’s properties.

In the last decade, readily available electronic devices have created unprecedented opportunities for teens to access a wide variety of information and media – both positive and negative – on the internet. Despite the increasing number of initiatives taking place worldwide intended to assess and mitigate the online risks encountered by children and adolescents, there is still a need for a better understanding of how adolescents use the internet and what consequences they may face. We conducted a cross sectional online survey of a convenience sample of 733 8th and 9th grade students in Utah. The survey contained eight questions regarding students’ exposure to three types of online risk scenarios: content risk, contact risk, and commercial risk. Independent variables included students’ online behaviors, use of social media and private messaging apps, and adult supervision of online activities. Logistic and negative binomial regression models indicated that female gender, social media use, and chatting with strangers were associated with exposure to multiple unsafe online scenarios. Our results provide critical information to practitioners involved in the development of educational initiatives by building a profile of potentially risky online behaviors and allow them to tailor their initiatives to meet the needs of more vulnerable populations.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

In view of the preparation for a post-LHC collider, the high-energy physics (HEP) community started from 2010 to discuss various options, including the use of HTS for very high field dipoles. Therefore, a small program was set in Europe aiming at exploring the possibility of using HTS for accelerator quality magnets. Based on various EU funded programs, though at modest levels, has enabled the European community of accelerator magnets to start getting experience in HTS and addressing a few issues. The program was based on use of REBCO tapes to form 10 kA Roebel cables, to be used to wind small dipoles of 30-40 mm aperture in the 5 T range. The dipoles are designed to be later inserted in a background dipole field (in Nb3Sn), to reach eventually a field level in the 16-20 T range, beyond the reach of LTS. The program is currently underway: more than 1 km tape of high performance (Je &gt; 500 A/mm2 at 20 T, 4.2 K has been manufactured and characterized, various 30 m long Roebel cables have been assembled and validated up to 13 kA, a few dipoles have been wound and tested, reaching at present 4.5 T in stand-alone (while a dipole made from race track coils with no-bore exceeded 5 T using stacked tape cable) and a test in a background field is being organized.

This paper reviews state of the art Additive Manufactured (AM) IN718 alloy intended for high temperature applications. AM processes have been around for decades and have gained traction in the past five years due to the huge economic benefit it brings to manufacturers. It is crucial for the scientific community to look into AM IN718 applicability in order to see a step-change in the production. Microstructural studies reveal that the grain structure plays a significant role in determining the fatigue lifespan of the material. Controlling IN718 respective phases such as the ϒ’', δ and Laves phase is seen to be crucial. Literature reviews have shown that the mechanical properties of AM IN718 were very close to its wrought counterpart when treated appropriately. Higher homogenization temperature and longer ageing were recommended to dissolve the damaging phases. Various surface enhancement techniques were examined to find out their compatibility to AM IN718 alloy that is intended for high temperature application. Laser shock peening (LSP) technology stands out due to the ability to impart low cold work which helps in containing the beneficial compressive residual stress it brings in high temperature fatigue environment.

The use of cow bones for biomaterial is still limited; accordingly, the cow bones waste has low economic value. Basically, a human’s and a cow’s bones are the same in terms of their forming compound. Aluminum (Al) has the potential to combine with hydroxyapatite (HAp) to make metal matrix composites (MMC) that have the potential for biomaterials. Compatible elements to be combined with Al and HAp are magnesium (Mg), titanium (Ti), and Copper (Cu), used self-high propagating temperatures synthesis (SHS). MMC can be processed to be a useful, solid product. Applying pressure to the SHS reaction and heating process may result in biomaterial composite product consisting of some matrix materials such as Al come from cans materials used in the experiment was HAp that was processed from cow bones calcination, added by can that contained aluminum and wetting agent, namely magnesium. The exothermic temperature was 800-900°C. The compaction process was done to allow materials to be bound. Based on the ASTM F138 standard for element of biomaterials, the porosity value was below 30% and hardness level above 40 HV. Cow bones and can-based composite sample with the composition of HAp-Al-Mg: 85%-10%-5% met the standard since the hardness value was: 73.3 HV with a porosity value of 29.88%.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

Conventional radiation therapy uses white X-rays that consist of a mixture of X-ray waves with various energy levels. In contrast, a monochromatic X-ray (monoenergetic X-ray) has a single energy level. Irradiation of high Z elements with a synchrotron generated monochromatic X-ray with the energy at or higher than the K-edge energy of the element results in the production of the Auger electrons that cause DNA damage leading to cell killing. Delivery of high Z elements into cancer cells and tumor mass can be facilitated by the use of nanoparticles. Mesoporous silica nanoparticles (MSNs) have been shown to be effective in delivering high Z elements to cancer cells. A proof of principle experiment was reported that demonstrated the feasibility of this approach. This opens up a possibility to pursue the Auger cancer therapy by the combined use of MSNs loaded with high Z elements and monochromatic X-rays. Similar cancer therapies using other types of quantum beams such as neutron, proton and carbon ion beams can be envisioned.

The paper provides information on significant contamination of real laboratory water with hydrophilic microimpurities. This fact suggests that researchers are practically dealing with microdispersed systems. However, this fact is usually neglected in the discussions of the causes of the anomalous properties of water. We will show that, when exposed to various factors of physical nature, water demonstrates reactions of the same type, namely, increased pH and electrical conductivity, reduced redox potential and viscosity, and enhanced bioavailability. Each exposure is accompanied by the destruction of aggregates of the dispersed phase and its transition to a fine-dispersed state. The relationship between this phenomenon and the change in the physicochemical properties of water is discussed.

The origin and significance of the tonalite–trondhjemite–granodiorite (TTG) units and the familiar metabasite xenoliths they host in the Yangtze Craton, China, remain controversial, and resolving these issues is important if we are to understand the evolution of the early Yangtze Craton. We focused on biotite–tremolite schist xenoliths in the Archean TTG units of the Kongling high-grade metamorphic terrane, and U–Pb dating of their zircons yielded ²⁰⁷Pb/²⁰⁶Pb ages of ca. 3.00 Ga, which provides a minimum age for the formation of the pre-metamorphic basic igneous rock. The host TTGs and late intrusive granitic dikes yield three groups of upper intercept ages at 2.87–2.88, 2.91–2.94, and 3.07 Ga, and a concordant age at 2.94 Ga, which suggest that the Yangtze continental nucleus underwent three important metamorphic–magmatic events in the Mesoarchean at ca. 3.00, 2.94, and 2.87 Ga. The biotite–tremolite schists have high ratios of K₂O/Na₂O and high contents of CaO, Cr, and Ni, thus showing the characteristics of high-K calc-alkaline island-arc volcanic rocks (basalt–andesite) that form by the partial melting of subducted oceanic crust. The data also provide further proof that a Mesoarchean metamorphic basement exists in the Yangtze Plate. Derivation of the magmatic protoliths of the biotite–tremolite schist enclaves from an oceanic crust during slab subduction, and the presence of these xenoliths within the TTG suite, indicate the existence of the initiation of plate tectonics during the Mesoarchean (≤2.94 Ga).