Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

Low Power Wide Area Networks (LPWAN) enable a growing number of Internet-of-Things (IoT) applications with large geographical coverage, low bit-rate, and long lifetime requirements. LoRa (Long Range) is a well-known LPWAN technology that uses a proprietary Chirp Spread Spectrum (CSS) physical layer, while the upper layers are defined by an open standard - LoRaWAN. In this paper, we propose a simple yet effective method to improve the Quality-of-Service (QoS) of LoRa networks by fine-tuning specific radio parameters. Through a Mixed Integer Linear Programming (MILP) problem formulation, we find optimal settings for the Spreading Factor (SF) and Carrier Frequency (CF) radio parameters, considering the network traffic specifications as a whole, to improve the Data Extraction Rate (DER) and to reduce the packet collision rate and the energy consumption in LoRa networks. The effectiveness of the optimization procedure is demonstrated by simulations, using LoRaSim for different network scales. In relation to the traditional LoRa radio parameter assignment policies, our solution leads to an average increase of 6% in DER, and a number of collisions 13 times smaller. In comparison to networks with dynamic radio parameter assignment policies, there is an increase of 5%, 2.8%, and 2% of DER, and a number of collisions 11, 7.8 and 2.5 times smaller than equal-distribution, Tiurlikova's (SoTa), and random distribution, respectively. Regarding the network energy consumption metric, the proposed optimization obtained an average consumption similar to Tiurlikova's, and 2.8 times lower than the equal-distribution and random dynamic allocation policies. Furthermore, we approach the practical aspects of how to implement and integrate the optimization mechanism proposed in LoRa, guaranteeing backward compatibility with the standard protocol.

We propose that, at equilibrium, statistically equal temperatures as mechanical torques are exerted on each kind of gas phase molecules as rates of translational action [@t=ʃmvds/dt=ʃmr2ωdϕ/dt=mv2, J]. These torques result from the impulsive density of resonant quantum fields with molecules, configuring the trajectories of gas molecules while balancing molecular pressure (p=NkT) against the density of field energy (J/m3). Gibbs energy fields contain no resonant quanta at zero Kelvin, with this measure of chemical potential diminishing in magnitude as translational action of the vapor molecules and quantum field energy increases with temperature. In illustration, we show how impulsive torques from quantum fields drive the reversible thermodynamics of Carnot’s heat-work engine cycle, sustain the decreasing atmospheric temperature gradient of increasing molecular entropy with altitude, support the translational action and field energy of vortical wind flow in anticyclones, frictionally warming the Earth’s surface while recycling greenhouse infrared absorption of surface radiation, generating electrical power from air flow in wind farms and destructive power in tropical cyclones. These cases all distinguish symmetrically between a causal field of impulsive quanta (Σhν) that energizes the action of matter and the resultant vis viva of molecular mechanics (mv2). The quanta of these different fields display mean wavelengths from 10-4 m to 1012 m, with mechanical advantages many orders of magnitude greater than the corresponding translational actions, though with mean quantum frequencies (v) similar to those of radial Brownian movement for independent particles (ω). These energy fields are also thermodynamically reversible reservoirs for heat, optimizing work processes on Earth and delaying the achievement of maximum entropy production from short wave solar radiation in conversion to outgoing long wave radiation to space.

Mereology stands for the philosophical concept of parthood and is based on a sound set of fundamental axioms and relations. One of these axioms relates to the existence of a universe as a thing having part all other things. The present article formulates this logical expression first as an algebraic inequality and eventually as an algebraic equation reading in words: The universe equals the sum of all things. “All things” here are quantified by a “number of things”. Eventually this algebraic equation is normalized leading to an expression The whole equals the sum of all fractions. This introduces “1” or “100%” as a quantitative – numerical - value describing the “whole”. The resulting “basic equation” can then be subjected to a number of algebraic operations. Especially squaring this equation leads to correlation terms between the things implying that the whole is more than just the sum of its parts. Multiplying the basic equation (or its square) by a scalar allows for the derivation of physics equations like the entropy equation, the ideal gas equation, an equation for the Lorentz-Factor, conservation laws for mass and energy, the energy-mass equivalence, the Boltzmann statistics, and the energy levels in a Hydrogen atom. It further allows deriving a “contrast equation” which may form the basis for the definition of a length and a time scale. Multiplying the basic equation with vectors, pseudovectors, pseudoscalars and eventually hypercomplex numbers opens up the realm of possibilities to generate many further equations.

The Science-Sustainability poses an interdisciplinary paradox. On the one hand, the science for sustainability has increased in OECD economies in and in China as well as in the US in particular; on the other hand; the sustainability situation has worsened (Co2 emission has risen). On the face value, the adverse correlation shows a paradox. However, without explicating the science-sustainability relationship, it leads to a premature conclusion. In this study, we have drawn on three concrete questions for concrete answers. First, whether and how interdisciplinary sciences—energy science and environmental science—contribute to the sustainability. Second, whether and how the Sino-US inter-institutional analysis varies in the science-sustainability paradox. The empirical analysis from a panel data in the interdisciplinary and inter-institutional context show mixed patterns in three ways. First, the increase in the environmental science shows an improvement in the sustainability; the energy science shows a decline in the sustainability. Second, the Chinese environmental science has a comparative advantage to American environment science for the sustainability development, and the Chinese energy science has a comparative disadvantage to the US in the sustainability development. Third, the environmental science mediates the energy science in the science-sustainability relationships. Standing alone, the increase in the energy science harms sustainability; mediated by environmental science, it benefits sustainability. The study explains the adverse role of energy science in Jevons Paradox. The study also offers some policy paths for further research how capitalisms differently innovate, form strategies, and implement the practice.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Miniaturization of electronics devices is often limited by the concomitant high heat fluxes (cooling load) and maldistribution of temperature profiles (hot spots). Thermal energy storage (TES) platforms providing supplemental cooling can be a cost-effective solution, that often leverages phase change materials (PCM). Although salt hydrates provide higher storage capacities and power ratings (as compared to that of the organic PCMs), they suffer from reliability issues (e.g., supercooling). ‘Cold Finger Technique (CFT)’ can obviate supercooling by maintaining a small mass fraction of the PCM in solid state for enabling spontaneous nucleation. Optimization of CFT necessitates real-time forecasting of the transient values of the melt-fraction. In this study artificial neural network (ANN) is explored for real-time prediction of the time remaining to reach a target value of melt-fraction based on the prior history of the spatial distribution of the surface temperature transients. Two different approaches were explored for training the ANN model, using: (1) transient PCM-temperature data; or (2) transient surface-temperature data. When deployed in a heat sink that leverages PCM based passive thermal management systems for cooling of electronic chips and packages, this maverick approach (using the second method) affords cheaper costs, better sustainability, higher reliability and resilience.

The atomic nucleus contains protons and neutrons surrounded by a structured electron cloud. Some combinations of protons and neutrons induce the nucleus to behave like a microscopic magnet, possessing a unique magnitude and orientation known as the nuclear magnetic moment (µ). When the numbers of protons and neutrons are both even then µ=0, but otherwise each nu-clide’s nuclear magnetic moment is unique. A second unique nuclear physical property relates to the nucleon binding energy (BE), which can be thought of as the energy between protons and neu-trons bound within the nucleus. The sequence of stable nuclides increases one nucleon at a time through 36Ar. The binding energy associated with the addition of each successive nucleon (∆BE) through this progression is unique. The hypothesis here is that the unique non-zero magnetic mo-ment and ∆ binding energy of each nuclide derive from its respective microscopic nuclear struc-ture, analogous to the way that the atomic physical properties of an element ultimately derive from its unique electron orbital structure. By extension, the identification of nuclear periodic pat-terns might eventually inform a theory of nuclear structure. The light, stable nuclides through 36Ar were arranged in ascending order according to atomic mass, and their nuclear magnetic mo-ments and binding energies were evaluated for periodic patterns. Fixed-period lengths from 4 through 18 nuclides per period were considered. These fixed periods, each of equal length, were stacked one upon the other and analyzed for vertical trends. The best evidence of periodicity in both µ and ∆BE converges precisely at the fixed 12-nuclide period. Implications for nuclear structure are discussed.

Here we mathematically model black holes and the early universe following dynamics similar to RLC electrical models, focusing on their similarities at the singularity. We use this mathematically modelling to hypothesize the evolution of an expanding universe as the result of a black hole collapse followed by its evaporation. Or model consists of several steps defined by: (1) the formation of a black hole following general relativity equations; (2) growth of the black hole modelled as a resistance-capacitance-like electrical circuit; (3) expansion of space-time following the disintegration of the black hole, modelled by RLC-like dynamics. In updating this article, version 2, we will expand by presenting three additional examples related to the theory of the generalization Boltzmann's constant in curved space-time and the theory of general and especial relativity. We will calculate the critical mass to produce a black hole in the LHC, the existence of a high temperature Bose-Einstein condensate and finally we will demonstrate the existence of a tangential force to the repulsion force in the disintegration of subatomic particles. In the update of this article, version 3, we will expand to develop two examples. First, we will present the relationship between M-theory, extra dimensions with the theory of the generalization of Boltzmann's constant in curved space-time. Secondly, we will propose the idea of ​​updating the Lambda-CDM model, considering the primordial gravitational waves to correctly describe the evolution of the universe.

To solve the problem of energy constraint and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

In Germany, as in many developed countries, over 60% of buildings were constructed before 1978, where most are in critical condition, requiring either demolition with plans for redevelopment or renovation and rehabilitation. Given the urgency of climate action and relevant sustainable development goals set by the United Nations, more attention must be shifted toward the various sustainability aspects when deciding on the strategy for renovation or redevelopment of existing buildings. To this end, this study focused on developing a smart decision support framework for aging buildings based on lifecycle sustainability considerations. The framework integrated digital technological advancements, such as building information modeling (BIM), point clouds processing with field information modeling (FIM)®, and structural optimization, together with life-cycle assessment to evaluate and rate the environmental impact of different solutions. Three sustainability aspects, namely, cost, energy consumption, and carbon emissions, were quantitatively evaluated and compared in two scenarios, namely, renovation, and demolition or deconstruction combined with redevelopment. A real building constructed in 1961 was the subject of the experiments to validate the framework. The result outlined the limitations and advantages of each method in terms of economics and environmental impact. It was further observed that optimizing the building design with the goal to reduce embodied energy and carbon in compliance with modern energy standards, was crucial to improve overall energy performance. This work demonstrated that the developed BIM-based framework to assess the environmental impact of rehabilitation work in aging buildings can provide effective ratings to guide decision-making in real-world projects.

As an irreplaceable ecological barrier, the ecological conservation developing area (ECDA) is vital for the integrated construction of urban and rural areas, and optimization and adjustment of industrial structure. Developing green agriculture is the foundation and guarantee for improving the rural ecological environment and meeting the increasing needs of farmers′ income. Issued by the Chinese government, No. 1 Central Document stated the necessity of promoting agricultural green development (AGD) and the related technologies in dealing with ecological pressure and resource shortages, especially for large cities like Beijing. However, few empirical studies have conducted on spatiotemporal variations of AGD in ECDA of large cities. Based on the green agricultural traits of Beijing and the accessible data, we evaluate AGD and analyze its spatial and temporal heterogeneity of Beijing ECDA by constructiing a framework with 13 indicators. The weight coefficients of AGD indicators were calculated by the projection pursuit method, with the district panel data from 2006 to 2016. The results demonstrated that energy consumption is a vital factor of green agriculture production, and agricultural output value per unit of the arable land area is the key to the green agricultural revenue. From 2006 to 2016, the AGD index of ECDA had an increasing trend till 2012, followed by a decreasing tendency. The AGD index of the northern region is higher than the southern of ECDA. The obstacle degree model was used to verify AGD limiting factors. They were poor infrastructure, slow agritourism, low labor productivity, and low resource utilization efficiency that varied by districts in ECDA. Given these findings, our study is conducive to the AGD evaluation at the district (county) level for ECDA of large cities and also provides important policy implications.

In the realm of the Internet of Things (IoT), a network of sensors and actuators collaborates to fulfill specific tasks. As the demand for IoT networks continues to rise, it becomes crucial to ensure the stability of this technology and adapt it for further expansion. Through an analysis of related works including Feedback-based Optimized Fuzzy Scheduling Approach (FOFSA) algorithm, Adaptive Task Allocation Technique (ATAT) and Osmosis Load Balancing algorithm (OLB), we identify their limitations in achieving optimal energy efficiency and fast decision-making. To address these limitations, this research introduces a novel approach to enhance the processing time and energy efficiency of IoT networks. The proposed approach achieves this by efficiently allocating IoT data resources in the Mist layer during the early stages. We apply the approach to our proposed system known as the Mist-based Fuzzy Healthcare System (MFHS) that demonstrates promising potential to overcome the existing challenges and pave the way for efficient Industrial Internet of Healthcare Things (IIoHT) of the future.

The introduction of electrical vehicle charging infrastructure including EV charger, renewable energy resource at secondary feeder in distribution system has been increased as one of countermeasure for global environmental issues. However, the Electric Vehicle Charging (EVC) infrastructure may act as the peak load in distribution system, which can adversely impact on the voltage stability when the electric vehicle is quickly charged. Therefore, to keep within the limit capacity of secondary feeder and allowable limit for feeder voltage, this paper proposes a stabilization method by the Energy Storage System (ESS) control strategy at secondary feeder in order to be not violated over than lower and upper limit. Also, this paper presents the estimation method to keep the proper standard value of State of Charge (SOC). From the simulation results, the voltage stabilization operation by ESS should make the feeder voltages of the distribution system(secondary feeder) introduced EVC Infra keep better voltage conditions, also estimation method to keep the proper standard value is confirmed that the SOC of ESS when is the standby condition could be exactly kept within the proper reference range.

The research is devoted to the problem of noise generation during flights of supersonic civil aircrafts. The effect of a thermally stratified energy source used to control the flow past a pointed cylinder aerodynamic models on the nearfield and ground pressure signatures, as well as on the perceived loudness in decibels (PLdB) on the ground is evaluated. The fields of parameters and the dynamics of the drag forces are studied for different values of temperature in the layers of the thermally stratified energy source and for different number of layers in it. It has been shown that when performing the flow control at freestream Mach numbers 1.5-2 using thermally stratified energy sources with the number of layers from 2.5 to 7.5 and rarefaction parameters in the layers from 0.15 to 0.3, no additional noise impact on the ground is introduced. Thus, the simulations showed that changing the surface pressure signature due to drag reduction does not necessarily imply a change in the PLdB on the ground.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

In this work, the author employs the quantum hydrodynamic formalism to achieve the geometrization of spacetime for describing the gravitational interaction within the framework of quantum theory. This approach allows for the development of an equation of gravity that is mathematically connected to the fermion and boson fields. This achievement is accomplished by incorporating two fundamental principles: covariance of the quantum field equations and the principle of least action. By considering these principles, a theory is established that enables the calculation of gravitational corrections to Quantum Electrodynamics, and potentially, to the standard model of particle physics as well. The theory also provides an explanation for two phenomena: the existence of a cosmological pressure density similar to quintessence, that is compatible with the small value of the observed cosmological constant, and the breaking of matter-antimatter symmetry at high energies offering insights into why there is an imbalance between the two in the early universe. In the cosmological modeling of the theory, there exists a proposal to account for the formation of supermassive black holes that are accompanied by their own surrounding galaxies, without relying on the process of mass accretion. The model, in accordance with recent observations conducted by the James Webb Space Telescope, supports the notion that galactic configurations were established relatively early in the history of the universe, shortly after the occurrence of the Big Bang.

Traditionally there is a gap between reactor operation and the consideration of nuclear waste in the final disposal. Fuel is produced and fuel must be disposed of in the view of the reactor operator, fuel has to be cleaned in the reprocessing and new solid fuel has to be produced in the view of the chemist. iMAGINE is designed to overcome this separation through the breakthrough development applying an optimized, integrative approach from cradle to grave of nuclear energy production as a first step to come as close as possible to the vision of zero waste nuclear power. It is described here the first time all in three the steps: reactor, fuel cycle, waste, providing the ratio behind each of the choices taken to come to the overall solution to open the discussion and thinking process on what could be achieved by a really innovative approach to integrated nuclear energy production. The opportunities regarding the handling of the remaining waste will be discussed with a view on the expectation of the final disposal community, the study ‘Nuclear waste from small modular reactors’, and the IAEA report ‘waste from innovative types of reactors and fuel cycles - a preliminary study. The aim of the is not to find answers to each of the raised points, but to identify first potential approaches and potentially promising ways to go, as well as to stimulate a discussion among experts. In the best case this could lead to a change of track for nuclear to become an even more sustainable and at least as important, trusted technology to help solve the net-zero challenge.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

An attempt is made to model the atomic nucleus as a combination of bound and free or unbound nucleons. Due to strong interaction, bound nucleons help in increasing nuclear binding energy and due to electroweak interaction, free or unbound nucleons help in decreasing nuclear binding energy. In this context, with reference to proposed 4G model of final unification and strong interaction, recently we have developed a unified nuclear binding energy scheme with four simple terms, one energy coefficient of 10.1 MeV and two small numbers 0.0016 and 0.0019. In this paper, by eliminating the number 0.0019, we try to fine tune the estimation procedure of number of free or unbound nucleons pertaining to the second term with an energy coefficient of 11.9 MeV. It seems that, some kind of electroweak interaction is playing a strange role in maintaining free or unbound nucleons within the nucleus. It is possible to say that, strong interaction plays a vital role in increasing nuclear binding energy and electroweak interaction plays a vital role in reducing nuclear binding energy. Interesting observation is that, Z can be considered as a characteristic representation of range of number of bound isotopes of Z. For medium, heavy and super heavy atoms, beginning and ending mass numbers pertaining to bound states can be understood with 2Z+0.004Z^2 and 3Z+0.004Z^2 respectively. With further study, neutron drip lines can be understood. Based on this kind of data fitting procedure and by considering the mass ratio of pions and electroweak bosons, existence of our 4G model of electroweak fermion of rest energy 584.725 GeV can be confirmed confidently.

Electricity demand prediction is vital for energy production management and proper exploitation of the present resources. Recently, several novel machine learning (ML) models have been employed for electricity demand prediction to estimate the future prospects of the energy requirements. The main objective of this study is to review the various ML models applied for electricity demand prediction. Through a novel search and taxonomy, the most relevant original research articles in the field are identified and further classified according to the ML modeling technique, perdition type, and the application area. A comprehensive review of the literature identifies the major ML models, their applications and a discussion on the evaluation of their performance. This paper further makes a discussion on the trend and the performance of the ML models. As the result, this research reports an outstanding rise in the accuracy, robustness, precision and the generalization ability of the prediction models using the hybrid and ensemble ML algorithms.

Based on the observation and reanalysis data, the relationship between Madden-Julian Oscillation (MJO) over the Maritime Continent (MC) and the tropical Pacific-Indian Ocean temperature anomaly mode is analyzed. The results showed that the MJO over the MC region (100°-140°E, 10°S-5°N) (referred to as MC-MJO) possesses prominent interannual and interdecadal variations and seasonally "phase-locked" features. MC-MJO is strongest in the boreal winter and weakest in the boreal summer. Winter MC-MJO kinetic energy variation has significant relationships with the El Niño-Southern Oscillation (ENSO) in winter and the Indian Ocean Dipole (IOD) in autumn, but it correlates better with the tropical Pacific-Indian Ocean associated mode (PIOAM). The correlation coefficient between the winter MC-MJO kinetic energy index and the autumn PIOAM index is as high as -0.43. This means that when the positive (negative) autumn PIOAM anomaly strengthens, the MJO kinetic energy over the winter MC region weakens (strengthens). However, the correlation between the MC-MJO convection and PIOAM in winter is significantly weaker. The propagation of MJO over the Maritime Continent differs significantly in the contrast phases of PIOAM. During the positive phase of the PIOAM, the eastward propagation of the winter MJO kinetic energy always fails to move across the MC region and cannot enter the western Pacific. However, during the negative phase of the PIOAM, the anomalies of MJO kinetic energy over the MC is not significantly. MJO can propagate farther eastward and enter the western Pacific. One thing must be pointed out that there is a significant difference between the propagation of MJO convection over the MC region in winter and that of the MJO kinetic energy. That said, the MJO convection is more likely to extend to the western Pacific in the positive phases of PIOAM than in the negative phases

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Material identification based on R_value (transparency natural logarithm ratio of low-energy to high-energy) of line-scan dual-energy X-ray transmission (DE-XRT) has a good prospect for industrial application. Unfortunately, the DE-XRT signals before attenuation cannot be directly measured, whereas their precision is very important to R_value. Therefore, a context-based signal synthesis method which takes the filtered signals that remove high-frequency noises and retain low-frequency actual fluctuations as the reference value, and takes into account the vertical (forward/column) direction and horizontal (scanning/row) direction anisotropy of line-scan images was proposed. The vertical is a time series with continuity of signal trend; the horizontal is a spatial characteristic with the fluctuation synchronization within the same row signals. The special synthesis evaluations of curve synthesis difference and surface synthesis difference were also proposed. Experimental results show that the tow evaluations are both only about 0.0007, and it only takes 35 ms to complete the surface synthesis of 119×119 pixels on the CPU with 3.4 GHz main frequency. The presented method can achieve high signal synthesis precision and calculation real-time, so as to facilitate DE-XRT material identification. It can be extended to improve the precision of numerical synthesis in other line-scan uncomplete signals.

This paper introduces a model-free, "on-the-fly" learning control strategy for arrays of energy converters with adjustable generator damping. The devices are arranged so that they are affected simultaneously by the energy medium. Each device uses a different control strategy, of which at least one has to be the machine learning approach presented in this paper. During operation all energy converters record the absorbed power and control output; the machine learning device gets the data from the converter with the highest power absorption and so learns the best performing control strategy for each state. Consequently, the overall network has a better overall performance than each individual strategy. This concept is evaluated for wave energy converter (WEC) with numerical simulations and experiments with physical scale models in a wave tank. In the first of two numerical simulations, the learnable WEC works in an array with four WECs applying a constant damping factor. In the second simulation, two learnable WECs were learning with each other. It showed that in the first test the WEC was able to absorb as much as the best constant damping WEC, while in the second run it could absorb even slightly more. During the physical model test, the ANN showed its ability to select the better of two possible damping coefficients based on real world input data.

In this paper, we make an attempt to estimate the famous Avogadro number with programming logics written in Python associated with advanced nuclear binding energy formulae. Average rest mass of nucleon, nuclear binding energy per nucleon and electron rest mass seem to play a vital role in estimating the unified atomic mass unit and Avogadro number. Interesting point to be noted is that, Avogadro number seems to be the inverse of the Unified atomic mass unit. With further study, it seems possible to estimate the unified atomic mass unit and Avogadro number accurately. Our interesting observation is that, short range strong nuclear force seems to have a vital role in deciding the accuracy of Avogadro number. For that purpose one may consider AI techniques along with newly observed atomic nuclides and their nuclear binding energies. For Z=6 to 118 and A_low=2Z and A_upper=3.5Z, estimated average value of Avogadro number is $N_{Average} \cong 6.01938 \times 10 ^{26}$. Considering the saturation of nuclear binding energy, at Z=26, $N_{Z=26} \cong \left(6.02229 \textrm{to} 6.02285\right) \times 10 ^{26}$. At academic level, our proposal can be given a chance as a case study. It is planned to develop a web application for this purpose.

Electric mobility is a global trend and necessity, with electric and solar boats offering a promising alternative for transportation electrification and carbon emission reduction, especially in the Amazon region. This study analyzes the system of a solar boat from the SIMA project, to be implemented at UFPA, using MATLAB software for modeling. The Simulink tool was utilized to model the system, focusing on operational parameters such as module voltage, converter voltage, and speed. Results indicate that the solar boat's operational cost is significantly lower compared to a similar internal combustion model, considering diesel's high consumption and cost. The environmental impact is also reduced, with nearly 72 tons of CO2 emissions avoided annually, thanks to Brazil's renewable energy matrix. Simulations confirmed the project's parameters, demonstrating the efficiency of digital twin technology in monitoring and predicting system performance. The study underscores the importance of digital twins and renewable energy in promoting sustainable transportation solutions, advocating for the replication of such projects globally. Future research should focus on further advancing digital twin applications in electric mobility to enhance predictive maintenance and operational efficiency.

The main goal of the review is to provide a summary and an assessment of the potential of fast-growing tree species for suitable transformation of agroforestry areas for biomass production in the Baltic Sea region. The article summarizes the research on the management process of agroforestry zones by establishing short rotation plantations with tree species Salix spp., Populus spp., Alnus spp. and looks at the perspectives of planning of these zones as biomass producers. Short rotation forestry (SRF) with a combination of species and a rotation time of 15 to 30 years, depending on the species used, is the most suitable approach for management of these agroforestry zones. Willows (Salix spp.) and poplars (Populus spp.) are suitable for short rotation coppice (SRC), as these tree species can be harvested at much shorter intervals, respectively, 1–5 and 4–10 years, facilitating their use in agricultural systems. In Alnus spp. short rotation plantation the life cycle for energy wood production is assumed to be 15-30 years. The black alder plantations in agroforestry zones are used for sawnwood and firewood production, with a rotation span of 20–40 years. Calculated economic agroforestry zone repayment period is about 10-15 years, if costs and prices as in 2021 are used.

In this paper, we study the performance of various deep reinforcement learning algorithms to enhance the energy management system of a microgrid. We propose a novel microgrid model that consists of a wind turbine generator, an energy storage system, a set of thermostatically controlled loads, a set of price-responsive loads, and a connection to the main grid. The proposed energy management system is designed to coordinate among the different flexible sources by defining the priority resources, direct demand control signals, and electricity prices. Seven deep reinforcement learning algorithms were implemented and are empirically compared in this paper. The numerical results show that the deep reinforcement learning algorithms differ widely in their ability to converge to optimal policies. By adding an experience replay and a semi-deterministic training phase to the well-known asynchronous advantage actor-critic algorithm, we achieved the highest model performance as well as convergence to near-optimal policies.

As the penetration of renewable energies increases, their acceptance of the power grid system is becoming an important issue. In the case of South Korea, a 22.9kV transformer is frequently utilized to reduce the power loss of the generated renewable energy transmission, so the power quality at the point of common connection (PCC) is inevitably influenced by the nonlinearity of the transformer and the uncertainty of the inductance and resistance of the transmission line. In this paper, we present a point of common connection voltage-modulated direct power control (PCCVM-DPC) system that enhances power quality at the PCC. First, we present the mathematical dynamics of active and reactive power at the PCC side, which contains the step-up transformer’s nonlinearity, the grid voltage harmonics, and the parameter uncertainties. By analyzing the disturbance terms of the PCCVM-DPC system, we present the disturbance observer (DOB) for the PCCVM-DPC system. To assess the efficacy of our approach, we perform comparative studies of the PCCVM-DPC without DOB and PCCVM-DPC with DOB by constructing the simulation environment based on the commercial step-up transformer and ESS inverter datasheet. We have validated that the active and reactive power control performance of the PCCVM-DPC with DOB outperforms the PCCVM-DPC without DOB from the observation that the current total harmonic distortion reduced by more than 40% compared to the PCCVM-DPC without the DOB.

With reference to our earlier published views on large nuclear gravitational constant , nuclear elementary charge and strong coupling constant , in this paper, we present simple relations for nuclear stability range, binding energy of isotopes and magic proton numbers.

In two previous papers, we calculated the dielectrophoresis (DEP) force and corresponding trajectories of high- and low-conductance 200-µm 2D spheres in a square 1x1mm chamber with plane-versus-pointed, plane-versus-plane and pointed-versus-pointed electrode configurations by applying the law of maximum entropy production (LMEP) to the system. Here, we complete these considerations for configurations with four-pointed electrodes centered on the chamber edges. The four electrodes were operated in either object-shift mode (two adjacent electrodes opposite the other two adjacent electrodes), DEP mode (one electrode versus the other three electrodes), or field-cage mode (two electrodes on opposite edges versus the two electrodes on the other two opposite edges). As in previous work, we have assumed DC properties for the object and the external media for simplicity. Nevertheless, every possible polarization ratio of the two media can be modeled this way. The trajectories of the spherical centers and the corresponding DEP forces were calculated from the gradients of the system’s total energy dissipation, described by numerically-derived conductance fields. In each of the three drive modes, very high attractive and repulsive forces were found in front of pointed electrodes for the high and low-conductance spheres, respectively. The conductance fields predict bifurcation points, watersheds, and trajectories with multiple endpoints. The high and low-conductance spheres usually follow similar trajectories, albeit with reversed orientations. In DEP drive mode, the four-point electrode chamber provides a similar area for DEP measurements as the classical plane-versus-pointed electrode chamber.

At present, under the background of high-quality development and the “carbon peaking and carbon neutrality” goal, China’s economic structure, industrial structure and energy structure have all begun green transformation and upgrading. The supply chain has become an important starting point for energy conservation and carbon reduction. In this context, enterprises have also ushered in huge environmental risk challenges and innovative development opportunities. This paper adopts Entropy-Weighted TOPSIS comprehensive evaluation method to analyze the green supply chain performance of "B" company, a new energy leading company, based on the theory of green development and corporate social responsibility. By establishing a green supply chain evaluation criteria system including four dimensions of finance performance, environment performance, operation performance and innovation performance, the weight of each evaluation criterion is objectively analyzed and calculated, and the green supply chain performance of "B" company from 2018 to 2022 is ranked. Based on this, comprehensive evaluations and sub-dimension evaluation are carried out and suggestions for improvement are put forward. At the same time, we hope to help other new energy vehicle companies optimize their own green supply chain practice mode.

The laser melting process (DED-LB-p) is used for the production of large components due to the high deposition rates. The large number of process parameters and printing strategies makes it difficult to optimize this process to achieve the optimal properties. Intensive post-processing is still the main obstacle to the widespread use of this process. In this work, the relationship between different printing strategies, printing strategies and process parameters on the microstructural, and tensile mechanical performance at room temperature is investigated. The porosity was measured in both printing directions. Grain orientation and size were analyzed by EBSD. A very low porosity of less than 0.4% was found in all printed samples. The samples printed with the optimized offset printing strategy show a significant improvement in tensile strength of 1000 MPa without heat treatment compared to other processing routes.

Industrial buildings have numerous energy-losing equipment, such as engines, ovens, boilers, and heat exchangers. Energy losses are related to inefficient energy use and lousy work conditions for the people inside the buildings. This work is devoted to the recovery of lost energy from industrial buildings. Firstly, the residual energy of the building is extracted to be used to warm water. Consequently, the work conditions of the people inside industrial buildings can be improved by maintaining the adequate temperature. The recovery energy is done by the multipurpose heat pump system (HP system). The working fluid used in the HP system is R134a, which is a traditional and cheap working fluid. The thermophysical properties of R134a are obtained through the PC-SAFT equation of state. This work presents a performance mapping based on the intercepted areas framework to evaluate which working conditions are the optimal operating variables. The latter depends on several key parameters, such as compressor work, heat delivery, heat absorbed, and exergetic efficiency. The results show that the optimal work conditions are found at different condenser and evaporator temperatures, and that may be limited by what the designer considers a good performance of the heat pump system.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

A two scalar field model that incorporates non Riemannian Measures of integration or usually called Two Measures Theory (TMT) is introduced, in order to unify the early and present universe. In the Einstein frame, a K-essence is generated and as a consequence for the early universe, we can have an Inflation for the very early universe and then, after inflation, an early dark energy period and a late dark energy period for the present universe dark, both dark energy epochs have a consistent generation of dark energy (DE), dark matter (DM) and stiff matter. This is obtained when the scale invariance is introduced and then is spontaneously broken from the integration of the degrees of freedom associated with the modified measures. The resulting effective potentials and K-essence in the Einstein frame produce the three flat regions corresponding to the different epochs mentioned before. For the first flat region, we can associate an inflationary universe. Also assuming this first plateau, we study the inflation in the framework of the slow-roll approximation. In this scenario under the slow roll approximation, we obtain a linear combination that is a constant. The corresponding cosmological perturbations in our model are determined and we also obtain the different constraints on the parameter-space from the Planck data. The slow roll approximation can be arranged so that the transition from inflation to the next flat region can be achieved without problems. In the following two flat regions, in addition to the inflation phase, representing the Early Dark Energy and Late Dark Energy Periods, with DE and also the DM, do not need to be introduced separately, they are instead a result of a K-essence induced by the multi measures, multi field theory. Therefore the scalars generate both the DE and the DM . Also a stiff matter component is automatically generated from the K-essence theory from two scalar fields. From the perturbative analysis associated to the perturbation solution of background, we find a correlation between the two scalars. Besides, we obtain that our model during the dark epoch has a behaviour of tracking freezing mode

Emission trading schemes (ETSs) have become vital tools in striving toward global emission reduction objectives and promoting a sustainable economy. This paper empirically investigates the impact of market conditions on interconnectedness within precious metals, clean energy, green bonds, and carbon markets, focusing on China and the EU ETSs as the study subjects. A TVP-VAR-based asymmetric connectedness approach is adopted to capture the evolving relationships between the variables of interest in the time–frequency domain. The empirical findings reveal that: First, time-varying asymmetric connectedness and spillover effects among clean energy, precious metals, green bonds, and carbon markets are identified in both time and frequency domains under diverse market conditions, with long-term connectedness asymmetry being particularly sensitive, although spillovers exhibit variations. Second, the role and intensity of net transmitters or receivers vary across market conditions and frequency domains, indicating the complex and nuanced nature of market interactions. The EU ETS demonstrates a higher level of connectivity with global markets for clean energy, precious metals, and green bonds when compared to the Chinese ETS. However, it also shows greater susceptibility to fluctuations in market conditions. These results have significant implications for both investors striving to build sustainable diversified portfolios and regulators endeavoring to craft effective policies for risk regulation and sustainable development.

In this study, the effects of grain size and gradation of riprap, overtopping flow depth and downstream slope of embankment on scouring and deposition characteristics at the downstream toe of the embankment was investigated. For the experiment, three different downstream slopes (1:2, 1:3, and 1:4), three different overflow depths (1, 2, and 3 cm), and three different sizes (d₅₀ of 16.41 mm, 8.48 mm, and 3.39 mm herein referred as No.5, 6 and 7 respectively) of riprap particles, respectively, were used in the laboratory. The experimental results demonstrated that the scour depth and deposition height increased with increasing energy head for each downstream slope condition. Among the three particle sizes, for No. 5 size particle shows the lowest scour depth and highest deposition height. For the 1:2 slope, the No. 5 particle size could resist scour 62% and 75% less than that of the No. 6 and No. 7 particles, respectively. For the 1:3 slope case, this was 31% and 46%, and for the 1:4 slope case, this was 39% and 49% less than the No. 6 and No. 7 size particles, respectively.

Wireless Sensor Network (WSN) and the sensing devices are considered part of the core components of the Internet of Things (IoT). Hence, the modeling of IoT-WSNs is fundamental to having a better understanding, management, and deployment of this kind of technology. A fundamental issue in WSN is energy consumption due to the inherent limitations of this resource in the sensor devices. On the other hand, several issues arise in heterogeneous scenarios due to the coexistence of different sensor devices. Therefore, the modeling process becomes challenging and must consider the different transmission and operation cycles and modes that the transmission protocol implements to assure successful functioning in terms of transmission, synchronization, and energy savings. A duty-cycled MAC WSN protocol (PSA-MAC) has been modeled based on a pair of two-dimensional Discrete-Time Markov Chain (2D-DTMC), whose solution in terms of stationary probability distribution is used by expressions that have been derived to evaluate the energy consumption of sensor devices that could be used for WSN-based IoT applications. Analytical results of average energy consumption are obtained, where the synchronization, data, and sleep periods of a full transmission cycle are considered in a heterogeneous scenario with different node classes and priority assignments. Also, the normal and awake operation cycles are considered to assure synchronization and energy savings. Moreover, the transmission schemes of SPT (transmission of single packets) and APT (transmission of packets in aggregation) are also considered in the model. These results are validated through discrete event-based simulations, and the obtained results are accurate.

Introduction: Transportation logistics play a pivotal role in facilitating both individual mobility and supply chain operations on a global scale. However, conventional transportation systems have contributed significantly to urban congestion and environmental degradation. In response to these challenges, there is a growing momentum towards the adoption of intelligent transportation systems (ITS) and sustainable transportation solutions. This research aims to explore the potential of renewable energy sources to power electric vehicles (EVs) and flying automobiles, thereby accelerating the transition towards a low-carbon future. Objectives: The primary objectives of this research are as follows: - Investigate the role of renewable fuels in powering both EVs and flying cars to reduce reliance on fossil fuels and mitigate carbon emissions. - Analyze the dynamic growth and sustainability implications of advancements in battery technology and alternative renewable energy sources, such as Hydrogen Fuel Cells. - Evaluate the challenges and opportunities associated with the integration of flying vehicles into existing transportation infrastructure, focusing on safety, airspace control, and infrastructure development. - Review insights and guidance to stakeholders on promoting sustainable transportation solutions for EVs and flying cars through the utilization of renewable energy sources and the reduction of carbon emissions from the literature. Methodology: This research employs a mixed-method approach, combining literature review, and causal loop diagram analysis. The literature review provides a comprehensive understanding of current trends, challenges, and opportunities in sustainable transportation and renewable energy technologies. A causal loop diagram is utilized to visualize the dynamic interactions between various factors influencing the adoption of EVs and flying cars, including technological advancements, policy interventions, and market dynamics. Results and Discussion: The findings of this research highlight the significant potential of renewable energy sources, such as solar, wind, and hydrogen, in powering both EVs and flying cars. Advances in battery technology and hydrogen fuel cells are identified as key drivers in accelerating the transition towards sustainable transportation systems. However, challenges remain in terms of infrastructure development, safety regulations, and airspace management for flying vehicles. Nevertheless, there is a noticeable advancement in reducing carbon emissions and reliance on fossil fuels with the widespread adoption of EVs. By harnessing renewable energy and implementing effective policy measures, stakeholders might able to promote the widespread adoption of sustainable transportation solutions, thereby contributing to environmental protection and societal well-being. Conclusion: Literally, this research underscores the importance of sustainable transportation solutions in addressing urban congestion, environmental pollution, and energy security concerns. By leveraging renewable energy sources and embracing technological advancements, such as EVs and flying cars, stakeholders pave the way for a more sustainable and resilient transportation system. However, concerted efforts are needed to overcome existing challenges and ensure the successful integration of these technologies into existing infrastructure. Through collaborative partnerships and innovative initiatives, a low-carbon future for transportation logistics can be achieved, benefiting both the environment and society as a whole.

This research review explores the synthesis of graphene quantum dots (GQDs) from biowaste for supercapacitor applications, driven by the need for sustainable and efficient energy storage technologies. GQDs, with their unique properties like high surface area and excellent conductivity, hold promise for enhancing supercapacitor performance. Various synthesis methods, including hydrothermal/solvothermal processes, chemical exfoliation, carbonization/pyrolysis, and microwave-assisted synthesis, are discussed alongside characterization techniques to evaluate GQD properties. Biowaste-derived GQDs demonstrate significant potential by improving specific capacitance and cycling stability in supercapacitor electrodes. Challenges such as scalability and material purity are identified, with future directions focusing on enhancing energy density, cycle life, and cost-effectiveness to propel the adoption of biowaste-derived GQDs in commercial energy storage applications.

To meet the dual-carbon objective, China's economy needs to move from a carbon-intensive to a green economy. Green technology innovation and renewable energy development are key to promoting green economic growth. The study uses 2010–2022 provincial panel data from 30 Chinese provinces. The super-efficient SBM model measures the province's green economic growth index. A panel fixed-effects model is used to experimentally evaluate how green technology innovation and renewable energy development affect green economic growth. Green financing moderates and a panel threshold model tests the threshold effect of renewable energy development on green economic growth. The results demonstrate that (1) China's green economic growth is rising and has a "U" shape. (2) all selected variables significantly impact green economic growth. However, population density, government intervention, and industrial structure are inversely associated with GEG. Green economic growth is significantly boosted by the moderate role of green finance in the development of renewable energy and green technological innovation. (3) Renewable energy development has a single threshold non-linear effect on green economic growth, depending on its development level and green technological innovation. Considering China's current condition and research findings, this study examines the green energy transition to promote green economic growth and high-quality economic development. Meanwhile, puts forward some important policy recommendations.

Along with the increasing industrialization of contries and population growth, the global. With the thougth of overcoming climate change and renducing greenhouse gas emissions in the atmosphere, interest in alternative sloar, wind, water, geothermal, tidal and ocean wave energy has significantly increased. Hydropower is one of the most used inexhaustible sources of energy on a global scale. The efficiency of water turbines can be increased by optimizing the blade cascade and the casing. For this purpose, research is conducted on specialized laboratory benches. The purpose is to determine the influencing parameters which affecting the nature of the power and cavitaion curves This paper presents the results of numerical and laboratoty studies of axial hydrokinetic turbines. A detailed analysis of the influence of the geometric parameters of the blades on the operating curves is made. A mathematica model for synthesis of the blade cascade is derived. An assessment of water energy soures has been made and sites of high energy potential have been pointed. The present material can be used for development of a methodology for calculation of efficient axial hydrokinetic turbines.

: Climate change necessitates urgent actions to mitigate carbon dioxide (CO2) emissions from fossil fuel-based energy generation. Among various strategies, the deployment of carbon capture and storage (CCS) solutions are critical for reducing emissions from point sources such as power plants and heavy industries. In this context, cryogenic carbon capture (CCC) via desublimation has emerged as a promising technology. While CCC offers high separation efficiency, minimal downstream compression work, and integration potential with existing industrial processes, challenges such as low operating temperatures and equipment costs persist. Ongoing research aims to address these hurdles in order to optimize the desublimation processes for widespread implementation. This review consolidates diverse literature works, providing insights into the strengths and limitations of CCC technology, including the latest pilot plant scale demonstrations. The transformative potential of CCC is first assessed on a theoretical basis, such as thermodynamic aspects and mass transfer phenomena. Then, recent advancements in the proposed process configurations are critically assessed and compared through key performance indicators. Furthermore, future research directions for this technology are clearly highlighted.

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimising MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based-control and deep learning techniques, including gated recurrent units (GRU), basic recurrent neural network (RNN) and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimises MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyper-parameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R2 value close to 1, representing a strong correlation between predicted and actual power values.

Nepal, primarily an agricultural country, heavily relies on agricultural residue and fuelwood for daily energy requirements. In 2022, total energy consumption was 640 PJ, with traditional sources accounting for 64.17%, and fuelwood comprising 58.53% of total fuel consumption. The estimated potential supply of agricultural residue is 26 million tonnes, yielding about 442 million GJ of energy in 2021. Biomass trading often emphasizes volume or weight, necessitating a rapid and non-destructive assessment of energy properties for mutual benefit, aiding in the identification, management, and utilization of biomass sources. In this study, 200 biomass samples were collected in two batches (126 and 74 samples) from various locations in Nepal. Using Partial Least Squares Regression (PLSR), a model was developed correlating higher heating value (HHV) from a bomb calorimeter and spectral data from Fourier Transform near-infrared spectroscopy (FT-NIRS) (3595 – 12,489 cm-1) sensor. PLSR models incorporated raw spectra, eight preprocessing techniques, the multi-preprocessing five-range method, and a genetic algorithm. Outliers in the first batch were identified, and the first batch divided into an 80% calibration set and a 20% validation set, while the second batch was designated as an unknown sample set. The optimum PLSR model, utilizing first derivative preprocessing, improved accuracy by 6.77%, with coefficients of determination in the calibration set, validation set, and unknown set as 0.9694, 0.9578, and 0.8089, respectively. Root mean square errors were 132.4790 J/g, 189.4800 J/g, and 360.8845 J/g for the calibration set (RMSEC), validation set (RMSEP), and unknown set (RMSEUN), respectively. The prediction to deviation ratio (RPD) for the validation set and unknown set was 4.9 and 2.4, respectively. The cross validation model of combined sample data of every sets showed the R2CV of 0.95 and RPDCV of 4.6 indicating the model could serve as a reliable and swift non-destructive alternative for evaluating biomass HHV using NIRS and ready for updating for industrial use. However, incorporating a larger number of representative samples is crucial to enhance accuracy and develop a more comprehensive global model for predicting biomass HHV.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

Directed energy deposition (DED) parameters were determined for near-β alloy Ti-55511 by employing statistical design of experiments (DOE) methods. Parameters resulting in fully dense freeform deposits were identified using two sequential DOEs. Single laser tracks were printed with several laser power, traverse rate, and powder feed rate settings in an initial DOE to identify promising build parameters. Capture efficiency and effective deposition rate were used to characterize and rank the single track deposits. The best parameters were then used to print solid cube with various X-Y and Z-overlaps (different hatch spacing, HS, and layer thickness, ZS) in a second DOE. Suitable deposition parameters were selected based on cube density and microstructure and were used to fabricate larger tensile samples for mechanical testing. Multiple parameter sets were found to provide dense Ti-55511 deposits with acceptable mechanical properties and parametric models showed statistical significance.

This Paper delves into the critical role played by fossil fuel-based polymers in promoting United Nations Sustainable Development Goals (SDGs) in the face of challenges brought about by swift population growth, suburbanization, and mechanization. It sheds light on the environmental and energy security recompences of converting plastic waste into biofuels and other valuable energy resources through state-of-the-art processes such as thermochemical conversion and pyrolysis. Besides, the research investigates the utilization of polymers in solar energy, energy storage, and low carbon transportation, emphasizing the inevitability of a dual approach that combines advancements in bio-based polymers and recycling technologies. It highlights the significance of collaborative endeavors involving governments, industries, and communities to overcome the technical, economic, and regulatory complications in transitioning towards a sustainable and circular plastic economy. Eventually, it showcases the potential of fossil fuel-based polymers in fostering a sustainable energy landscape, conducive to decarbonization efforts, and endorsing environmental sustainability.

Entropy generation, formulated by combining the first and second laws of thermodynamics with an appropriate thermodynamic potential, emerges as the difference between a phenomenological entropy function and a reversible entropy function. The phenomenological entropy function is evaluated over an irreversible path through thermodynamic state space via real time measurements of thermodynamic states. The reversible entropy function is calculated along an ideal reversible path through the same state space. Entropy generation models for various classes of systems—thermal, externally loaded, internally reactive, open and closed––are developed via selection of suitable thermodynamic potentials. Here we simplify thermodynamic principles to specify convenient and consistently accurate system governing equations and characterization models. The formulations introduce a new and universal Phenomenological Entropy Generation (PEG) theorem. The systems and methods presented––and demonstrated on grease degradation, battery charging and discharging, metal fatigue and pump flow––can be used for design, analysis, and support of diagnostic monitoring and optimization.

In this paper, we study the constrained minimization problem for an energy functional which is related to the following Kirchhoff type equation \begin{equation*} -\Big(\eta+b\big(\int_{\R^{3}}|\nabla u|^{2}dx\big)^{s}\Big)\Delta u+V(x)u=\mu u +\lambda|u|^{p}u,\end{equation*} where $b$ is a positive constant, parameters $\eta\geq0, \lambda>0$, exponents $s>0$, $0

This paper deals with a method of calculating the self and mutual inductances of various air coils located arbitrarily in space. Known elementary solutions (the Biot-Savart formulas) were used to determine the magnetic field of infinitely thin current loops and infinitely thin wires of finite length linking magnetically other coils. Unlike commonly used algorithms, these elementary solutions were not extensively transformed analytically but were used to perform calculations by direct numerical integration. This enabled very quick and accurate obtaining of the self-inductance values as well as determining the dependence of mutual inductances on the position of both coils. This method allows analysis of different coil configurations (misaligned coils, inclined to each other, etc.) that other methods do not cover. It also enables the determination of the forces acting on the coils, as well as the calculation of the magnetic field distribution from any coil configuration. The obtained results were compared with those presented by other authors.

Media is obtaining a leading role in contemporary strategic communication, the development especially visible in the context of social-political and geopolitical conflicts. This study introduces an interdisciplinary theory of Social Laser and applies it in the analysis of social mobilization around the current militarized situation in Eastern Europe. We analyze quantitatively the content of three Swedish newspapers and qualitatively the related Facebook discussions. As demonstrated, social lasing has been employed as an instrument in information warfare. An “information tsunami” was generated by the Swedish national mass media at the outbreak of military events in March-May 2022. It shaped social dynamics on the related social media platform. The intensity of dissident actions increased when the information pressure subsided.

As the international community attaches importance to environmental and climate issues, carbon dioxide emissions in various countries have been subject to constraints and limits. Carbon trading market, as a market tool to reduce greenhouse gas emissions, has gone through a development process from a pilot carbon market to a national carbon market in China. At present, the industries included in the national carbon market are mainly the electric power industry, and the carbon emissions of the electric power industry account for about 40% of the national carbon emissions. According to the construction history of foreign carbon markets, China's future carbon quota allocation will gradually transition from free allocation to auction allocation,the auction mechanism will bring a heavy economic burden to the electric power industry, especially the thermal power generation industry. Therefore, this study takes Guangdong Province as an example to optimize the power generation mix with the objective of minimizing the total economic cost after the innovative introduction of the carbon quota auction mechanism and constructs an optimization model of the power generation mix based on the auction ratio by comprehensively applying the system dynamics model and the multi-objective linear programming model and systematically researches the power generation structure under different auction ratios with the time scale of months and quantitatively evaluates the economic inputs needed to reduce the greenhouse gas emissions.The results of the study show that after comprehensively comparing the total economic cost, renewable energy development and carbon emissions, it is the most scientific and reasonable to set the auction ratio of carbon allowances at 20%, which achieves the best level of economic and environmental benefits.

The present state of the natural environment is significantly influenced by the construction sector. Due to the large amounts of consumed natural resources and materials as well as the high volume of emitted pollutants, the building industry is considered to have a key influence in achieving a global sustainable development. A considerable part of the ecological impact of the built environment is influenced by the energy consumed for creating appropriate indoor conditions as well as by the greenhouse gases that are emitted during the operation stage of a building’s life cycle. Therefore, the energy performances of existing buildings must be significantly improved in the near future. This paper analyzes the influence of the thermal insulation thickness of walls on the linear thermal transmittances and the heating demand of an existing building. The resulted values show that while increasing the insulation of the walls leads to a serious heat demand reduction, a deep renovation of the building cannot be achieved solely by using this solution.

The paper deals with an electrothermal model of a thermoelectric converter dedicated to performing simulations of coupled thermal and electrical phenomena taking place in harvesting processes. The proposed model is used to estimate the electrical energy gain from waste heat that would be sufficient to supply electronic circuits, in particular autonomous battery-less nodes of wireless sensor networks (WSN) and Internet of Things (IoT) devices. The developed model is not limited to low power electronic solutions such as WSN or IoT; it can also be scaled up and applied to simulations of considerably higher thermal power conversion. In the paper, a few practical case studies are presented that show the feasibility and suitability of the proposed model for complex simultaneous simulation processes, in both electrical and thermal domains. The first example deals with a combined simulation of the electrothermal model of a thermoelectric generator (TEG) and an electronic harvester circuit based on Analog Devices’ power management integrated circuit LTC3108. The second example relates to the thermalization effect in heat sink-less harvesting applications that could be mitigated by a pulse mode operation.

Chest X-ray (CXR) is the first tool globally employed to detect cardiopulmonary pathologies. These acquisitions are highly affected by scattered photons due to the large field-of-view required. Scatter in CXRs introduces background in the images, which reduces their contrast. We developed three deep learning-based models to estimate and correct the scatter contribution to CXRs. We used a Monte Carlo (MC) ray-tracing model to simulate CXRs from human models obtained from CT scans using different configurations (depending on the availability of dual-energy acquisitions). The simulated CXRs contained the separated contribution of direct and scattered X-rays in the detector. These simulated datasets were then used as the reference for the supervised training of several NN. Three NN models (single and dual energy) were trained with the MultiResUNet architecture. The performance of the NN models was evaluated on CXRs obtained with the MC code from chest CTs of patients affected by COVID-19. The results showed that the NN models were able to estimate and correct the scatter contribution to CXRs with an error <5%, being robust to variations in the simulation setup and improving the contrast in soft tissue. The single-energy model was tested with real CXRs, providing robust estimations of the scatter-corrected CXRs.

The paper presents a thorough examination of the burgeoning field of utilizing manufacturing waste for sustainable energy generation, aligning with the global imperative for resource efficiency and clean energy solutions. With the manufacturing sector being a significant contributor to waste generation, this study explores innovative approaches to transform waste materials into valuable resources, thereby mitigating environmental impacts and contributing to a circular economy. This work critically reviews current trends, emphasizing technological advancements, policy interventions, and market dynamics shaping the manufacturing waste utilization landscape. Noteworthy developments, such as advanced sorting technologies and the integration of digital solutions, are discussed in detail, showcasing their role in enhancing the efficiency of waste management processes. The study outlines future trends in the field, anticipating a shift towards closed-loop systems guided by circular economy principles. This comprehensive review aims to contribute to the discourse on sustainable waste management and energy generation by providing a holistic perspective on the field's current state and offering insights into the future trajectories that will propel manufacturing waste toward a more sustainable and circular future. The synthesis of technological innovation, collaborative efforts, and evolving regulatory frameworks presents a compelling case for the continued exploration of manufacturing waste as a valuable resource in the pursuit of a more sustainable and energy-efficient world.

A new utilization of entropy in the context of buckling is presented. The novel concept connecting strain energy and entropy for a pin-ended strut is derived. This concept rationalizes the ranking of buckling modes based on strain energy under the assumption of given entropy. By assigning identical entropy to all buckling modes, they can be ranked according to their deformation energy. Conversely, with identical strain energy assigned to all modes, ranking according to entropy is possible. Decreasing entropy was found to represent the scaling factors of buckling modes that coincide with the measurement of initial out-of-straightness imperfections in IPE160 beams. Applied to steel plane frames, scaled buckling modes can be used to model initial imperfections. It is demonstrated that the entropy (scale factor) for given energy roughly decreases with the inverse square of the mode index. For practical engineering, the study presents the possibility of using scaled buckling modes of steel plane frames to model initial geometric imperfections. Entropy proves to be a valuable complement to strain energy in structural mechanics.

By employing the stochastic extension of the Madelung quantum-hydrodynamic description within a discrete methodology, we establish a solution using the path integral approach to explore the progression of quantum states' superposition. This investigation aims to understand the eventual establishment of a stable end-state configuration amid the backdrop of gravitational background fluctuations. The model identifies the circumstances that lead to a limited range of interaction for the quantum potential, allowing for the emergence of sizeable, classically described macroscopic phenomena. The theory unveils the lowest achievable level of uncertainty in an open quantum system and investigate its congruence with the localized behaviors of macroscopic classical systems. The study examines agreements and differences with decoherence theory and the Copenhagen interpretation of quantum mechanics, and evaluates the impact of wave function decay on the measurement process.

(1) Background: The imaging energy range of a typical Compton camera is limited due to the fact that scattered gamma photons are seldom fully absorbed when the incident energies are above 3 MeV. Further improving the upper energy limit of gamma-ray imaging has important application significance in active interrogation of special nuclear materials and chemical warfare agents, as well as range verification of proton therapy; (2) Methods: To realize gamma-ray imag-ing in a wide energy range of 0.3~7 MeV, a principle prototype, named a portable three-layer Compton camera, was developed using the scintillation detector that consist of an silicon photo-multiplier array coupled with a Gd3Al2Ga3O12:Ce pixelated scintillator array. Implemented in a list-mode maximum likelihood expectation maximization algorithm, a far-field energy-domain imaging method based on two-interaction and three-interaction events was applied to estimate the initial energy and spatial distribution of gamma-ray sources. The simulation model of detec-tors was established based on Monte Carlo simulation toolkit Geant4. The reconstructed images of a 133Ba, a 137Cs and a 60Co point-like sources were successfully obtained with our prototype in laboratory tests and compared with simulation studies; (3) Results: The proportion of effective imaging events accounted for about 2%, which made our prototype realize reconstructing the distribution of a 0.05 μSv/h 137Cs source in 10 seconds. The angular resolution for resolving two 137Cs point-like sources was 15°. Additional simulated imaging of the 6.13 MeV gamma-rays from 14.1 MeV neutron scattering with water preliminarily demonstrated the imaging capability for high incident energy; (4) Conclusions: We concluded that the prototype had good imaging per-formance in a wide energy range (0.3~7 MeV), which showed potential in several MeV gam-ma-ray imaging applications.

Mechanical robustness and high energy efficiency of composite materials are immensely important in modern stretchable, self-powered electronic devices. However, the availability of these materials and their toxicities are challenging factors. This paper presents the mechanical and energy-harvesting performances of low-cost natural rubber composites made of stearic acid-modified diatomaceous earth (mDE) and carbon nanotubes (CNTs). The obtained mechanical properties were significantly better than those of unfilled rubber. Compared to pristine diatomaceous earth, mDE has higher reinforcing efficiencies in terms of mechanical properties because of the effective chemical surface modification by stearic acid and enhanced filler-rubber interactions. The addition of a small amount of CNT as a component in the hybrid filler systems not only improves the mechanical properties but also improves the electrical properties of the rubber composites and has electromechanical sensitivity. For example, the fracture toughness of unfilled rubber (9.74 MJ/m3) can be enhanced by approximately 484% in a composite (56.86 MJ/m3) with 40 phr (per hundred grams of rubber) hybrid filler, whereas the composite showed electrical conductivity. At a similar mechanical load, the energy-harvesting efficiency of the composite containing 57 phr mDE and 3 phr CNT hybrid filler was nearly double that of the only 3 phr CNT-containing composite. The higher energy-harvesting efficiency of the mDE-filled conductive composites may be due to their increased dielectric behaviour. Because of their bio-based materials, rubber composites made by mDE can be considered eco-friendly composites for mechanical and energy harvesting applications and suitable electronic health monitoring devices.

To compare the quality of low-energy VMIs obtained with three DECT platforms according to phantom diameter. Three sections of the Mercury Phantom 4.0 were scanned on two generations of split-filter CTs (SFCT-1st and SFCT-2nd) and on one Dual-source CT (DSCT). Noise power spectrum (NPS), task-based transfer function (TTF) and detectability index (d’) were assessed on VMIs from 40 to 70keV. Highest noise magnitude values were found with SFCT-1st and noise magnitude was higher with DSCT than with SFCT-2nd for 26-cm (10.2±1.3%) and 31-cm (7.0±2.5%), and the opposite for 36-cm (-4.2±2.5%). The highest average NPS spatial frequencies and TTF values at 50% (f50) values were found with DSCT. For all energy levels, f50 values were higher with SFCT-2nd than SFCT-1st for 26-cm (3.2±0.4%) and the opposite for 31-cm (-6.9±0.5%) and 36-cm (-5.6±0.7%). The lowest d’ values were found with SFCT-1st. For all energy levels, d’ values were lower with SFCT-2nd than with DSCT for 26-cm (-6.2±0.7%), similar for 31-cm (-0.3±1.9%) and higher for 36-cm (5.4±2.7%). In conclusion, compared to SFCT-1st, SFCT-2nd exhibited lower noise magnitude and higher detectability values. Compared with DSCT, SFCT-2nd had lower noise magnitude and higher detectability for the 26-cm but the opposite was true for the 36-cm.

Wood plastic composite usage and demands have increased due to chemical, and mechanical properties when compared to plastic materials. However, because of the possibility of structural and mechanical changes of the material when exposed to external environment more research needs to be done. In the present study yellow birch/HDPE composites materials made by injection molding were treated by zinc oxide and exposed to fungal rots. Mechanical properties of the composites were assessed by Tensile and Izod impact test. The impact energies of the samples loaded with 30 % ZnO-treated fibers and exposed to G. trabeum and T. versicolor decreased, compared to when samples were not treated with ZnO. The mechanical properties of all samples treated with ZnO and exposed to rot decreased which were reported as a decreased Young's modulus and impact energies. ZnO prevented mycelium proliferation which was nonexistent on samples. It has been noted that the decrease in mechanical properties of treated samples was due to NaOH used to dissolve the ZnO powder.

Quantum-dot cellular automata (QCA) are a promising nanoscale computing technology that exploits the quantum mechanical tunneling of electrons between quantum dots in a cell and electrostatic interaction between dots, in neighboring cells. QCA can achieve higher speed, lower power, and smaller areas than conventional complementary metal–oxide–semiconductor (CMOS) technology. Developing QCA circuits in a logically and physically reversible manner can provide exceptional reductions in energy dissipation. The main challenge of reversible QCA design is to maintain reversibility down to the physical level. The arithmetic logic unit (ALU) is an essential component of the central processing unit (CPU) of a computer. It performs various arithmetic and logical operations on the data that the CPU processes. Current QCA ALU designs are either irreversible or logically reversible; however, they lack physical reversibility, a crucial requirement to increase energy efficiency. In this paper, we present a novel multilayer design for a logically and physically reversible QCA ALU based on majority gates as the key components, which can perform 16 different operations. We use QCADesigner-E software to simulate and evaluate energy dissipation. The proposed logically and physically reversible QCA ALU offers an improvement of 88.8% in energy efficiency. Compared to the next most efficient 16-operation QCA ALU, this ALU uses 51% fewer QCA cells and 47% less area.

This article explores matter collineations (MCs) of static plane-symmetric spacetimes, considering the stress-energy tensor in its contravariant and mixed forms. We solve the MC equations in two cases: when the energy-momentum tensor is nondegenerate and degenerate. For the case of degenerate energy-momentum tensor, we employ a direct integration technique to solve the MC equations, which leads to an infinite-dimensional Lie algebra. On the other hand, when considering the nondegenerate energy-momentum tensor, the contravariant form results in a finite-dimensional Lie algebra with dimensions of either 4 or 10. However, in the case of the mixed form of the energy-momentum tensor, the dimension of the Lie algebra is infinite. Moreover, the obtained MCs are compared with those already found for covariant stress-energy.

The established classical method of treating oil refinery effluent is flotation followed by biological treatment. Membrane bioreactors (MBRs) offer more advanced treatment, producing a clarified and potentially reusable treated effluent, but demand robust pretreatment to remove oil and grease (O&G) down to consistent, reliably low levels. An analysis of a full-scale conventional oil refinery ETP based on flotation alone, coupled with projected performance, energy consumption and costs associated with a downstream MBR, have demonstrated satisfactory performance of flotation-based pre-treatment. The flotation processes, comprising an API separator followed by dissolved air flotation (DAF), provided ~90% removal of both total suspended solids (TSS) and O&G coupled with 75% COD removal. The relative energy consumption and cost of the pretreatment, normalised against both the volume treated and COD removed, was considerably less for the API-DAF sequence compared to the MBR. The combined flotation specific energy consumption in kWh was found to be almost an order of magnitude lower than for the MBR (0.091 vs 0.86 kWh per m3 effluent treated), and the total cost (in terms of the net present value) around one sixth that of the MBR. However, the nature of the respective waste streams generated and end disposal of waste solids differs significantly between the pretreatment and MBR stages.

The aim of this work was to determine the potential of using a pulsed electric field (PEF) and ultra-sound (US) apparatus to produce mitragynine extracts from Mitragyna speciosa dried leaves. Four modes of the device were tested: PEF, US, US + PEF, and PEF + US. The results were compared with extracts obtained using a conventional technique (maceration, as the control). Changes in the mitragynine content were determined with the liquid chromatography/mass spectrometry (LC-MS/MS) method. The LC-MS/MS analysis showed that the mitragynine contents from kratom extracts using four different modes were different. The highest extraction (106.63 ± 0.85 mg/L) of mitragynine was achieved by the PEF + US procedure, followed by US + PEF (97.27 ± 1.33 mg/L), with increased extraction efficiencies of 45.81 ± 0.59% and 33.00 ± 1.85%, respectively. Moreover, the total energy consumption under the combination technique was 25.0% lower than that with PEF assistance. Furthermore, scanning electron microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR) provided confirmatory evidence for the extraction of M. speciosa by the prototype. This study confirmed that PEF and US devices can be considered a green alternative method and may contribute to the application of agricultural products.

This article provides a comprehensive review of the intersection of 5G technology and Beyond, and Smart Grids, focusing on the potential of Vehicle-to-Fog as an industrial alternative for addressing energy efficiency challenges in data processing. This study aims to investigate relevant articles and patents to understand the collaborative potential between 5G and Smart Grids. It explores how to establish new regulatory standards within the architectural framework of 5G to facilitate decentralized data processing and remodel energy consumption patterns. The hypothesis suggests that decentralized 5G architecture and Smart Grids can be most effectively applied through vehicular fogging powered by solar energy. A combined quantitative and qualitative methodology guides the exploration of articles and patents. The study concludes by advocating for new standards that embrace decentralized 5G data processing, emphasizing the potential of Vehicle-to-Fog and the future deployment of 6G technology in Smart Grids. These advancements can significantly enhance energy efficiency in the context of 5G and pave the way for future innovations.

In recent years, unquestionable warnings like the negative impacts of CO2 emissions, the necessity of utilizing sustainable energy sources, and the rising demand for municipal electrification have been issued. In this study, by incorporating two significant assumptions, such as electricity production in close proximity to the business location and only renewable energy resource usage, a modest off-grid hybrid energy system is designed. To construct the system, a number of elements such as wind generators (WG), photovoltaic arrays (PV), battery banks, and bi-directional converters are taken into account. Moreover, a real case in Malmö, Sweden, is considered. To optimize the system, a bi-objective problem is developed, and it is solved by proposing a particle swarm optimization (PSO) approach to provide the load requirements (with a maximum allowance of 0.1% unmet) for a nearby supermarket (approximately 1000 m2). Moreover, to verify the obtained results, the developed system is simulated using HOMER Pro software, and the results are compared and discussed. The contribution of this study is to provide off-grid or local clients around the world with a dependable and affordable option by minimizing both the baseline cost of energy and the net current expenditure in the desired system. The best-obtained results by the proposed PSO offered 160 PVs, 5 WGs, and 350 batteries, respectively, while the best solution found by the simulation method was using 384 PVs, 5 WGs, and 189 batteries for the considered off-grid system.

Owing to the escalating adoption of IoT systems across various domains, the demand for mobile and wireless power sources has surged. Although conventional batteries typically serve as energy storage components, the current low-power consumption devices necessitate eco-friendly alterna-tives. In this study, we designed, fabricated, and characterized an energy harvesting device that repurposes mechanical vibrations. A three-beam design was employed to harvest energy across a broader range of potential frequencies. Finite element models were simulated to ascertain the first bending moment for both sets of beams. A nanostructured piezoelectric multilayer film made of ZnO was deposited onto an AISI 304 steel substrate, and a photosensitive resin seismic mass was implemented. Low-cost techniques generating minimal environmental waste were leveraged in the fabrication process. The piezoelectric film was deposited using a spray nebulization technique involving recycled materials and cost-effective equipment. Micrographs of the layers unveiled the presence of nanospheres with diameters of 250 nm. Employing a custom-made shaker, output voltages of 1.08 V and 180 mV, and power outputs of 1.849 µW and 16.2 nW were achieved for each set of beams. The electrical characterization was conducted using a custom-made shaker, repurposing materials for this objective.

This article presents a review of current advances and future prospects in the field of forecasting renewable energy generation using machine learning (ML) and deep learning (DL) techniques. With the increasing penetration of renewable energy sources (RES) into the electricity grid, accurate forecasting of their generation becomes crucial for efficient grid operation and energy management. Traditional forecasting methods have limitations, and thus ML and DL algorithms have gained popularity due to their ability to learn complex relationships from data and provide accurate predictions. This paper reviews the different approaches and models that have been used for renewable energy forecasting and discusses their strengths and limitations. It also highlights the challenges and future research directions in the field, such as dealing with uncertainty and variability in renewable energy generation, data availability, and model interpretability. Finally, this paper emphasizes the importance of developing robust and accurate renewable energy forecasting models to enable the integration of RES into the electricity grid and facilitate the transition towards a sustainable energy future.

From the standpoint of Neoliberal Institutionalism, this study explores Malaysia's participation in activities that make energy the topic and/or object of foreign policies, whether through bilateral or multilateral engagements. This research, which aims to evaluate the relevance of energy in Malaysia's economy and diplomacy and to explain Malaysia's reason for its involvement in these cooperations, is necessary because of Malaysia's growing involvement in the global energy market. Information for this study was gathered from a variety of government sources, interviews, published statistical data, and previous studies. The study demonstrates how vital energy is to Malaysia's economy. The Lao PDR-Thailand-Malaysia-Singapore Power Integration Project (LTMS-PIP) initiative, in which Malaysia is participating, is evidence of the viability of multilateral power commerce in the area. The Peninsula Gas Utilisation (PGU) pipeline in Peninsular Malaysia and the Four-Fuel Diversification Policy 1981 (4FDP 1981), which increases natural gas utilisation, are related to Malaysia's participation in the Malaysia-Thailand Joint Development Area (MT-JDA). Malaysia would want to think about streamlining its energy administration.

For a decade, the studies of dynamic control for unmanned aerial vehicles took a large interest, where drones as a useful technology in different areas were always suffering from several issues like instability-high energy consumption of batteries - inaccuracy of tracking targets. Different approaches are proposed for dealing with the non-linearity issues which present the most important features of this system. This paper describes our focus on the most common control strategies, known as model predictive control MPC, by developing a model based on the sensors embedded in our Tello quadrotor used for indoor purposes. The original controller of Tello quadrotor is supposed to be a slave, where the designed model predictive controller is created in MATLAB and imported to another embedded system, considered as a master; the objective of this model is to track the reference trajectory, almost keeping the stability of the system and ensure the low energy consumption. In the first part, a profound description of the modelling process of a dynamic model for drones is presented, explaining the design of MPC controller with both linear and non-linear strategies built in MATLAB. In the final part, simulation and results are discussed regarding its behaviour and performance, highlighting the MPC model's important role on drones' energy consumption profile.

Monte Carlo Filtering (MCF) is one of the methods of Experimental Statistical Energy Analysis (E-SEA), which allows the correction of a negative LF (Loss Factor). In this article, a modification of the MCF method, called DESA (Diagonal Extension of the Search Area), is proposed. The technique applies a non-uniform extension of the search area when generating a population of normalized energy matrices. The degree of expansion of the search area is controlled by the Diagonal Penalty Factor (DPF). The authors demonstrated the method's effectiveness on a system that could not be identified in several frequency bands by the classical MCF method. After applying DESA, it was possible to fill in the problematic bands that were missing CLF and DLF values. The paper also proposes a way to minimize the errors introduced by using overly high DPF values.

Evaluating the integrity of structures is an important issue in engineering applications. The use of vibration-based techniques has become a common approach to assessing cracks, which are the most often occurring damage in structural elements. When involving an inverse method, it is necessary to know the influence of the position and the geometry of the crack on the modal parameter changes. The geometry of the crack, both in size and shape, defines the damage severity (DS). In this study, we present a method (DS-SHC) used for estimating the DS for closed and open transverse cracks in beam-like structures by using the intact and damaged beam deflections under its weight and a Stochastic Hill Climbing (SHC) algorithm. After describing the procedure of applying DS-SHC, we calculate for a prismatic cantilever beam the severities for different crack types and depths. The results are tested by comparing the DS obtained with DS-SHC with those acquired from dynamic tests made using professional simulation software. We obtained a good fit between the severities determined in these two ways. Afterward, we performed laboratory experiments and find out that the severities obtained with the DS-SHC method can accurately predict the frequency changes due to the crack. Hence, these severities are a valuable tool for damage detection.

Renewable energy technologies (RET) are critical to the sustainable development of modern societies. Hong Kong has set up a RET theme park so as to fulfill the needs of and impart knowledge on RET through entertainment and educational activities. Such understanding aids in formulating appropriate future park designs and neuromarketing strategies to maximize the attractiveness of the park. Therefore, this study attempts to investigate potential visitors’ preferences with regard to cartoon characters in the RET theme park, especially for student groups to meet the “edutainment” theme of the park. A total of 400 people have participated in this study. Findings indicate that Snoopy, Mickey Mouse, and Donald Duck show a high degree of likeness of presence in the RET theme park.

Strained layer superlattice (SLS) material system is being considered for large format, small-pitch and low-cost focal plane arrays for different applications. To address difficulties associated to focal plane arrays fabrication arising from mesa-isolation etching or complex surface treatment/ passivation process, planar structures have been considered. In this work, the recent progress on planar SLS photodetector using ion-implantation for device isolation is presented. The devices are presented here are nBn and pBn heterostructure InAs/InAsSb SLS photodetector, where Zn and Si were chosen as the ion implants, respectively. The electrical and optical performance of the devices were compared along with comparison with mesa-etched device, to give deeper view of the device performance.

We show that quantum mechanics can be constructed as a classical field theory that correctly describes all basic quantum effects, by combining the Maxwell and Dirac equations. It is shown that for a self-consistent union of the Maxwell and Dirac equations into a unified classical field theory, it is necessary to introduce an additional short-range tensor field, which compensates the intrinsic electrostatic field of the electron wave inside the atom. For the combined Maxwell-Dirac field, the stress-energy tensor is constructed. We show that in the nonrelativistic limit this theory naturally transforms into the self-consistent Maxwell-Pauli theory and allows describing all basic quantum effects in the framework of classical field theory without any quantization.

Sustainability is pivotal in the urban transformation strategy in order to reach more resource-efficient, resilient and smarter cities. The goal of being a sustainable city should drive the decisions for city interventions. Nonetheless, impacts need to be quantified, lacking of standard and/or common methodologies that could be replicable across multiple cities. There exist many initiatives aiming at defining indicators and assessment procedures, but without convergence in the definition of terms and application methodologies, making complex its real implementation. Within mySMARTLife project (GA#731297), a KPI-driven evaluation framework is defined with the aim of covering the multiple pillars of a city (i.e. energy, mobility, citizens, economy) in a holistic way. This methodology also defines the concepts and terms to guide urban planners and/or experts at time of implementing the framework in a specific city. The evaluation framework has been deployed in the three cities of Nantes, Hamburg and Helsinki and some lessons learnt have been extracted, such as the necessity of providing a definition of measurement boundary to avoid interpretations. Thanks to a co-creation strategy, the main difficulties and issues from the cities have been taken into consideration for increasing the replicability.

Direct electric curing (EC) is a new green curing method for cement-based materials that improves the early mechanical properties via the uniform high temperature produced by Joule heating. To understand the effects of EC and steam curing (SC) on the mechanical properties and microstructure of cement-based materials, the mortar was cured at different temperature-controlled curing regimes (40°C, 60°C and 80°C). Meanwhile, mechanical properties, hydrate phase and pore structure of specimens were investigated. The energy consumption of two curing methods was compared and analyzed. The results show that the EC specimens have better and more stable growth of mechanical strength. The pore structure of EC specimen is also better than that of SC specimen at different maintenance ages. However, the hydration degree and products of samples cured by EC are similar to that SC samples. The energy consumption of EC is lower than SC. This study provides an important technical support for the EC in the production of energy-saving and high early-strength concrete precast components.

The heavy metal lead (Pb) can irreversibly damage the human nervous system. To help understand Pb-induced damage, we applied a genetically encoded Förster resonance energy transfer (FRET)-based Pb biosensor Met-lead 1.44 M1 to two living systems to monitor the concentration of Pb: induced pluripotent stem cell (iPSC)-derived cardiomyocytes as a semi-tissue platform, and Drosophila melanogaster fruit flies as an in vivo animal model. Different FRET imaging modalities were used to obtain FRET signals, which represented the presence of Pb in the tested samples in different spatial dimensions. Using iPSC-derived cardiomyocytes, the relationship between beating activity (20–24 beats per minute, bpm) determined from the fluctuation of fluorescent signals and the concentrations of Pb represented by the FRET emission ratio values of Met-lead 1.44 M1 was revealed from simultaneous measurements. Pb (50 μM) affected the beating activity of cardiomyocytes, whereas two drugs that stop the entry of Pb differentially affected this beating activity: verapamil (2 μM) did not reverse the cessation of beating, whereas 2-APB (50 μM) partially restored this activity (16 bpm). The results clearly demonstrate a potential of this biosensor system as an anti-Pb drug screening application. In the Drosophila model, Pb was detected within the adult brain or larval central nervous system (Cha-gal4>UAS-Met-lead 1.44 M1) using fast epifluorescence and high-resolution two-photon 3D FRET ratio image systems. The tissue-specific expression of Pb biosensors provides an excellent opportunity to explore the possible Pb-specific populations within living organisms. We believe that this integrated Pb biosensor system can be applied to the prevention of Pb poisoning and advanced research on Pb neurotoxicology.

The concept of a ‘just transition’ encompasses political and policy imperatives to minimise the harmful impacts of industrial and economic transitions on workers, communities and society more generally, and to maximise their potential benefits. This imperative has gained heightened importance as governments commit to reducing greenhouse gas emissions. A wide range of policies strategies and initiatives have been adopted by national and regional governments to facilitate and help manage a just transition. It is a concept that is increasingly being put into practice. This scoping study identifies and compares strategies, policies and practices that are presently being implemented in order to manage a just transition across 25 countries and 74 regions alongside European Union-level policies. This work develops a typology of policy instruments to manage just transitions and identifies implementation gaps and leading practices.

In this paper, a multi-operator differential evolution algorithm (MODE) is proposed to solve the Optimal Power Flow (OPF) problem and is called MODE-OPF. The MODE-OPF utilizes the strengths of more than one differential evolution (DE) operator in a single algorithmic framework. Additionally, an adaptive method (AM) is proposed to update the number of solutions evolved by each DE operator based on both the diversity of population and quality of solutions. This adaptive method has the ability to maintain diversity at the early stages of the optimization process and boost convergence at the later ones. The performance of the proposed MODE-OPF is tested by solving OPF problems for both small and large IEEE bus systems (i.e., IEEE-30 and IEEE-118) while considering the intermittent solar and wind power generation. To prove the suitability of this proposed algorithm, its performance has been compared against several state-of-the-art optimization algorithms, where MODE-OPF outperforms other algorithms in all experimental results and thereby improving a network's performance with lower cost. MODE-OPF decreases the total generation cost up to 24.08%, the real power loss up to 6.80% and the total generation cost with emission up to 8.56%.

The land-surface developments of the European Centre for Medium-range Weather Forecasts (ECMWF) are based on the Carbon-Hydrology Tiled Scheme for Surface Exchanges over Land (CHTESSEL) and form an integral part of the Integrated Forecasting System (IFS), supporting a wide range of global weather, climate and environmental applications. In order to structure, coordinate and focus future developments and benefit from international collaboration in new areas, a flexible system named ECLand which would facilitates modular extensions to support numerical weather prediction (NWP) and society-relevant operational services, e.g. Copernicus, is presented . This paper introduces recent examples of novel ECLand developments on (i) vegetation, (ii) snow, (iii) soil, (iv) open water/lake (v) river/inundation, and (vi) urban areas. The developments are evaluated separately with long-range, atmosphere-forced surface offline simulations, and coupled land-atmosphere-ocean experiments. This illustrates the benchmark criteria for assessing both, process fidelity with regards to land surface fluxes and reservoirs of the water-energy-carbon exchange on the one hand, and on the other hand the requirements of ECMWF’s NWP, climate and atmospheric composition monitoring services using an Earth system assimilation prediction framework.

Accessing energy in the world is crucial nowadays. Energy is an essential factor to achieve other SDGs including SDG7. However, the determination and evaluation of the relationship between different energy scenarios to achieve SDG 7 and other SDGs have not done yet. This paper seeks to fill this gap by investigating how energy seniors can contribute to achieving SDG 7 and other SDGs. Web of Science, ScienceDirect and Scopus databases were utilized for conduction a systematic review. A total finial 25 from 249 papers were filtered from 2015 to December 2020 via inclusion and exclusion criteria. This review involves six seniors of energy which primary linked to achieving the SDG 7 and other SDGs: modern energy 20% (n = 5/25), energy access 16% (n = 4/20), energy efficiency 8% (n= 2/16), renewable energy 28% (n= 7/14), energy services 8% (n= 2/7), and miscellaneous energy 20% (n= 5/5). This systematic review explores the opportunities, constraints and limitations, recommendations, and new directions. The results show that different energy scenarios contribute to achieving mainly (SDG7) and other SDGs. The outcomes from this systematic review provide a sense of direction for future researchers for future studies in this domain.

Wrist-worn fitness trackers and smartwatches are proliferating with an incessant attention towards health tracking. Given the growing popularity of wrist-worn devices across all age groups, a rigorous evaluation for recognizing hallmark measures of physical activities and estimating energy expenditure is needed to compare their accuracy across the lifespan. The goal of the study was to build machine learning models to recognize physical activity type (sedentary, locomotion, and lifestyle) and intensity (low, light, and moderate), identify individual physical activities, and estimate energy expenditure. The primary aim of this study was to build and compare models for different age groups: young [20-50 years], middle (50-70 years], and old (70-89 years]. Participants (n = 253, 62% women, aged 20-89 years old) performed a battery of 33 daily activities in a standardized laboratory setting while wearing a portable metabolic unit to measure energy expenditure that was used to gauge metabolic intensity. Tri-axial accelerometer collected data at 80-100 Hz from the right wrist that was processed for 49 features. Results from random forests algorithm were quite accurate in recognizing physical activity type, the F1-Score range across age groups was: sedentary [0.955 – 0.973], locomotion [0.942 – 0.964], and lifestyle [0.913 – 0.949]. Recognizing physical activity intensity resulted in lower performance, the F1-Score range across age groups was: sedentary [0.919 – 0.947], light [0.813 – 0.828], and moderate [0.846 – 0.875]. The root mean square error range was [0.835 – 1.009] for the estimation of energy expenditure. The F1-Score range for recognizing individual physical activities was [0.263 – 0.784]. Performances were relatively similar and the accelerometer data features were ranked similarly between age groups. In conclusion, data features derived from wrist worn accelerometers lead to high-moderate accuracy estimating physical activity type, intensity and energy expenditure and are robust to potential age-differences.

Abstract. The purpose of this review is to investigate the nature of privacy concerns in the context of Smart Local Energy Systems (SLES) to understand how SLES providers can minimize both users’ concern, and cause for concern, around privacy. We conducted a rapid realist review and thematic framework analysis against Bronfrenbrenner’s socio-ecological model to understand privacy concerns in different contexts. A common privacy concern was that sharing detailed energy use data had the potential to reveal information about home life, and to intrude upon people’s sense of autonomy, choice and control. Evidence suggests that people are willing to accept newdata sharing technologies if the benefits of doing so are clear, anticipated, and mutually beneficial. Building trust, through increasing knowledge and understanding was a mechanism for overcoming privacy concerns, but this was mediated by the organization providing the information. Non-profit organizations were more trusted to ensure appropriate safeguards to privacy were in place. One key barrier to participation with good supporting evidence was that people can resist perceived intrusions on their privacy. This could be actively resisted by refusing to install data collection technologies or passively by non-participation in adapting energy use behaviors: both of which are necessary for SLES to achieve their goals of managing energy demand and building resilience in smart grids.

Peer-to-peer (P2P) energy trading – where energy prosumers transact directly between each other – could help enable transition to a low-carbon energy system. If it is to be supported in policy and regulation, it is important to anticipate the distributional impacts (or how it might impact segments of society differently). However, real-world evidence on P2P energy trading is currently extremely limited. To address this challenge in the short- to medium-term, this study aimed to explore what might be learned from the extensive body of research on a comparable offering in the accommodation sector: Airbnb. A realist review approach was employed to maximise transferability of findings, focused on what mechanisms are thought to lead to what distributional outcomes, in what contexts. On the basis of the review, participation in (and receipt of benefits of) P2P energy trading schemes would be expected to represent disproportionately those living in areas with network management challenges, who are younger and more highly educated. The review also raised the prospect of discrimination on the basis of characteristics such as race and gender where there are high levels of individual choice over who to trade with. Recommendations include monitoring, incentivising diversity, anonymization, and limiting trading choices.

The mangrove plant Acanthus ilicifolius and its relative, A. mollis, have been previously proved to possess diverse pharmacological effects. Therefore, evaluating the differentially expressed proteins of these species under tidal flooding stress is essential to fully exploit and benefit from their medicinal values. The roots of A. ilicifolius and A. mollis were exposed to 6 h of flooding stress per day for 10 days. The dry weight, hydrogen peroxide (H2O2) content, anatomical characteristics, carbon and energy levels, and two-dimensional electrophoresis coupled with MALDI-TOF/TOF MS technology were used to reveal the divergent flooding resistant strategies. A. ilicifolius performed better under tidal flooding stress, which was reflected in the integrity of the morphological structure, more efficient use of carbon and energy, and a higher percentage of up-regulated proteins associated with carbon and energy metabolism. A. mollis could not survive in flooding conditions for a long time, as revealed by incomplete cell structures of the roots, less efficient use of carbon and energy, and a higher percentage of down-regulated proteins associated with carbon and energy metabolism. Energy provision and flux balance played a role in the flooding tolerance of A. ilicifolius and A. mollis.

The outbreak of SARS-COV-2 disease 2019 (COVID-19) abruptly changed the patterns in electricity consumption, challenging the system operations of forecasting and balancing supply and demand. This is due to the mitigation measures that include lockdown and Work from Home (WFH), which decreased the aggregated demand and remarkably altered its profile. Here, we characterise these changes with various quantitative markers and compare it with pre-COVID-19 business-as-usual data using Great Britain (GB) as a case study. The ripple effects on the generation portfolio, system frequency, forecasting accuracy and imbalance pricing are also analysed. An energy data extraction and pre-processing pipeline that can be used in a variety of similar studies is also presented. Analysis of the GB demand data during the March 2020 lockdown indicates that a shift to WFH will result to a net benefit for flexible stakeholders, such as consumer on variable tariffs. Furthermore, the analysis illustrates a need for faster and more frequent balancing actions, as a result of the increased share of renewable energy in the generation mix. This new equilibrium of energy demand and supply will require a redesign of the existing balancing mechanisms as well as the longer-term power system planning strategies.

A photovoltaic-thermal (PVT) collector is a solar-based micro-cogeneration system which generates simultaneously heat and power for buildings. The novelty of this paper is to conduct energy and exergy analysis on PVT collector performance under two different European climate conditions. The performance of the PVT collector is compared to a PV panel. Finally, the PVT design is optimized in terms of thermal and electrical exergy efficiencies. The optimized PVT designs are compared to the PV panel performance as well. The main focus is to find out if the PVT is still competitive with the PV panel electrical output, after maximizing its thermal exergy efficiency. The PVT collector is modelled into Matlab/Simulink to evaluate its performance under varying weather conditions. The PV panel is modelled with the CARNOT toolbox library. The optimization is conducted using Matlab gamultiobj-function based on Non-Dominated Sorting Genetic Algorithm-II (NSGA-II). The results indicated 7.7% higher annual energy production in Strasbourg. However, the exergy analysis revealed a better quality of thermal energy in Tampere with 72.9% higher thermal exergy production. The electrical output of the PVT is higher than from the PV during the summer months. The thermal exergy- driven PVT design is still competitive compared to the PV panel electrical output.

This study presents a new kinetic scheme for the mass yield prediction of waste lignocellulosic biomasses treated by Hydrothermal Carbonization (HTC). The proposed reactions are based on the decomposition, solubilization, and polymerization of each main fraction of the biomass: cellulose, hemicellulose, and lignin. The ash content was assumed to be inert. The kinetic parameters have been obtained by non-linear adjustment using a data set with 220 experimental runs collected from the literature. The results indicate that the pre-exponential factors range was from 7.33 x10¹ to 1.412x10⁵ min^-1, and activation energies were between 33.75 y 225.3 kJ/mol. A good fit is achieved between the observed and predicted data with an R² of 0.81 and an RMSE of 7.7 %. The proposed scheme was validated with the experimental data obtained by the HTC of sawdust (Pinus radiata) and rapeseed (Brassica napus). The experiments were carried out at temperatures of 190, 220, and 250 ºC and reaction times of 0, 30, 60, 90, and 120 min. The predicted values showed an average error of 2.3 and 3.5 %, respectively. Therefore, the kinetic scheme is a useful tool in the conversion analysis of waste biomass treated by HTC.

Wind power output is highly dependent on the wind speed at the selected site, therefore wind-speed distribution modeling is the most important step in the assessment of wind energy potential. This study aims at accurate evaluation of onshore wind energy potential in seven coastal cities in the south of Iran. Six Probability Distribution Functions (PDFs) were examined over representative stations. It has been deduced that the Weibull function, which was the most used PDF in similar studies, was only applicable to one station. Here, Gamma offered the best fit for three stations and for the other ones, Generalized Extreme Value (GEV) performed better. Considering the ranking of six examined PDFs and the simplicity of Gamma, it was identified as the effective function in the southern coasts of Iran bearing in mind the geographic distribution of stations. Besides, six turbine power curve functions were contributed to investigate the capacity factor. That was very important, as using only one function could cause under- or over-estimation. Then, stations were classified based on the National Renewable Energy Laboratory system. Last but not least, examining a range of wind turbines enabled scholars to extend this study into the practice and prioritize development of stations considering budget limits.

The outdoor field test of the 4-terminal on Si tandem photovoltaic module (specifically, InGaP/GaAs on Si) was investigated and performance model, considering spectrum change affected by fluctuation of atmospheric parameters, was developed and validated. The 4-terminal on Si tandem photovoltaic module had about 40 % advantage in seasonal performance loss compared with standard InGaP/GaAs/InGaAs 2-terminal tandem photovoltaic module. This advantage is expanded in (subarctic zone) < (temperate zone) < (subtropical zone). The developed and validated model used all-climate spectrum model and considered fluctuation of atmospheric parameters, and can be applied every type of on-Si tandem solar cells.

Efficient alternatives in energy production and consumption are constantly investigated by increasingly strict policies. In this way, the pollutant emissions that contribute to the greenhouse effect reduce and sustainability of the electricity sector increase. With more than a third of the world's energy consumption, buildings have great potential to contribute these sustainability goals. Additionally, with growing incentives in the Distributed Generation (DG) and Electric Vehicle (EV) industry, it is believed that Smart Buildings (SBs) can be a key in the field of residential energy sustainability in the future. In this work, an energy management system in SBs are developed to reduce the power demanded of a residential building. In order to balance the demand and power provided by the grid, microgrids such as Battery Energy Storage System (BESS), EVs and Photovoltaic Generation panels (PV) are used. Here, a Mixed Binary Linear Programming formulation (MBLP) is proposed to optimize the charge and discharge scheduling of EVs and also BESS. In order to show the efficiency of the model, a case study involving three scenarios and an economic analysis is considered. The results point a 65% reduction in peak load consumption supplied by grid and a 28.4% reduction in electricity consumption costs.

Because of the near-term risk of extreme weather events and other adverse consequences from climate change, and, at least in the longer term, global fossil fuel depletion, there is world-wide interest in shifting to noncarbon energy sources, especially renewable energy (RE). Because of possible limitations on conventional renewable energy sources, researchers have looked for ways of overcoming these shortcomings by introducing radically new energy technologies. The largest RE source today is bioenergy, while solar energy and wind energy are regarded as having the largest technical potential. This paper reviews the literature on proposed new technologies for each of these three RE sources: microalgae for bioenergy, photolysis and airborne wind turbines. The main finding is that their proponents have underestimated the difficulties facing their introduction on a very large scale.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.