The aim of the study was to assess the effect of the addition of inulin and the replacement of part of inulin with apple fiber on the physicochemical and organoleptic properties. Moreover, the survival of Bifidobacterium animalis ssp. Lactis Bb-12 and Lactobacillus rhamnosus was studied in sheep milk ice cream. There was no effect of apple fiber and the type of bacteria on the number of bacteria of the probiotics after fermentation. As a result of freezing, mixture containing Bifidobacterium animalis ssp. Lactis Bb-12, there was a significant reduction in the bacterial from 0.39 log cfu g −1 to 0.46 log cfu g −1. In all ice cream on the 21st day of storage, it exceeded 10 log cfu g –1, which means that the ice cream retained the status of probiotic products. The Lactobacillus rhamnosus ice cream showed a lower yellow colour compared to the Bifidobacterium Bb-12 ice cream. The overrun of sheep's milk ice cream was within a range from 78.50% to 80.41%. The appearance of sheep's milk ice cream is influenced considerably by the addition of fiber and the type of bacteria and the interaction between the type of bacteria and the addition of fiber and storage time and fiber.

The paper presents construction, laboratory tests as well as the first field application of a new fiber-optic rotational seismograph. The system based on fiber-optic gyroscope (FOG) with determined Angle Random Walk of the order of 10-8 rad/Sqrt(s) and a few rad/s maximum detectable amplitude of rotation in the frequency range from DC to 328.12 Hz. It has been designed for rotational seismology area of interest. This work also presents exemplary relevant measurements which were conducted using a set of two devices installed in the geophysical observatory in Książ, Poland.

In this paper, we investigate an animal-human cohabitation problem with the help of machine learning and fiber-wireless (FiWi) access networks integrating cloud and edge (fog) computing. We propose an early warning system which detects wild animals nearby road/rail with the help of wireless sensor networks and alerts passing vehicles of possible animal crossing. Additionally, we show that animals' detection at the earliest and the related processing, if possible, at sensors would reduce the energy consumption of edge devices and the end-to-end delay in notifying vehicles, as compared to the scenarios where raw sensed data needs to be transferred up the base stations or the cloud. At the same time, machine learning helps in classification of captured images at edge devices, and in predicting different time-varying traffic profiles-- distinguished by latency and bandwidth requirements-- at base stations, including animal appearance events at sensors, and allocating bandwidth in FiWi access networks accordingly. We compare three scenarios of processing data at sensor nodes, base stations and a hybrid case of processing sensed data at either sensors or at base stations, and showed that dynamic allocation of bandwidth in FiWi access networks and processing data at its origin leads to lowering the congestion of network traffic at base stations and reducing the average end-to-end delay.

We discuss three key points: defining mathematically the notions of phase, symmetry breaking, topological defects and their stability in a formal language of homotopy theory and fiber bundle formalism; postulating and proving two theorems for successive symmetry breaking scenarios in condensed matter physics and cosmology, and demonstrating application of theorems to superfluid Helium 3 and Kibble-Lazarides-Shafi (KLS) walls, supporting and mathematically justifying the results of [Volovik, 2020].

Weather has significant impact on growth and plants development. It is important to analyze the influence of changing climate conditions on expression of plants agronomical characters. Two flax varieties were grown from 1987 to 2018 in the North-West of Russia. Whether conditions and their influence on flax agronomic characters were analyzed using variance and correlations analyses. Significant influence of year conditions on the manifestation of all evaluated characters was revealed. Starting from June high temperatures accelerate the development of plants at all stages. Prolongation of germination - flowering period is the most important for fiber productivity improvement. Oppositely, for formation of high quality fiber fast ripening in hot weather after flowering is preferable. Such data give possibility to predict the amount and quality of yield. Usage of weather conditions data also permits to compare results obtained in different years. Suggested method of year’s meteorological conditions classification can be used in other genebanks for systematization and analyses of crops field evaluation results. Correlation analyses reviled 3 correlated pleiades: (1) pleiade of productivity, (2) pleiade of fiber quality and yield, (3) pleiade of the growing season phases duration, the sums of active temperatures and precipitation during each period. Great influence of growing conditions on economically valuable traits indicates the necessity of searching for genotypes with stable characters manifestation for breeding new varieties, which will give stable yield and fiber of good quality.

A new covered yarn system is proposed in this manuscript by controlling the tension of the spandex elastic yarn drawing.. By analyzing the relationship between the draw ratio and yarn tension, it has been verified that the new tension controlled drawing system is feasible and results in yarns with superior quality and process stability.

Two isotropic pitches were prepared by air blowing and nitrogen distillation method using ethylene tar (ET) as a raw material. And correspondent carbon fibers were obtained through conventional melt spinning, stabilization and carbonization. The structures and properties of resultant pitches and fibers were characterized and their differences were discussed in this work. The results showed that introduction of the oxygen by air blowing method could quickly increase the yield and softening point of pitch. Moreover, the air blown pitch (ABP) composed of linear methylene chains of aromatic molecules while the nitrogen distilled pitch (NDP) mainly contained polycondensed aromatic rings, which was due to the oxygen containing functional groups existed in ABP could impede order stack of pitch molecules and form methylene bridge structure, instead of aromatic condensed structure like NDP. Meanwhile, the spinnability of ABP was not decreased even containing 2.31 wt% oxygen. In contrast, ABP had narrower molecular weight distribution, which contributed to better stabilization properties and higher tensile strength of carbon fiber. The tensile strength of carbon fibers from ABP was reached to 860 MPa with fiber diameter of about 10 μm, which was higher than that of NDP-derived carbon fibers of 640 MPa.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

The aim of this research work is to get a method for Galfenol electrodeposition thought which we can control the desired percentage of Ga versus Fe that has the maximum magnetostriction constant. Galfenol is electrodeposited on an optical fiber with an imbedded Fiber Bragg Grating (FBG) in its core. The final objective, that goes further of the scope of this research, is to get an optical magnetostrictive sensor. The device will sense magnetic field or current based on the combination of this magnetostrictive Galfenol, that will stress the optical fiber with the application of magnetic field or current and will change the reflected wavelength of the FBG as a consequence of the variation of the Bragg wavelength. We have developed a method of electrodeposition that allows controlling the density of current in the electrodeposition process in order to get the desired percentage of Ga and Fe in the alloy Ga X Fe 1-x. We have manufactured a set of samples with different parameters (as density of current and pH) and we have characterized these samples morphological, structural and magnetically. With this research we want to give to the scientific community the groundwork to design magnetostrictive optical sensors based on and FBG coated by giant magnetostrictive material. In this paper we have developed a method of covering the optical fiber controlling the composition of (Ga X Fe 1-X) in order to be able to get the maximum magnetostriction constant.

Prebiotic dietary fiber supplements are commonly consumed to help meet fiber recommendations and improve gastrointestinal health by stimulating beneficial bacteria and the production of short-chain fatty acids (SCFAs), molecules beneficial to host health. The objective of this research project was to compare potential prebiotic effects and fermentability of five commonly consumed fibers using an in vitro fermentation system measuring changes in fecal microbiota, total gas production and formation of common SCFAs. Fecal donations were collected from three healthy volunteers. Materials analyzed included: pure beta-glucan, Oatwell (commercially available oat-bran containing 22% oat β-glucan), xylooligosaccharides (XOS), WholeFiber (dried chicory root containing inulin, pectin, and hemi/celluloses), and pure inulin. Oatwell had the highest production of propionate at 12 h (4.76 μmol/mL) compared to inulin, WholeFiber and XOS samples (p<0.03). Oatwell’s effect was similar to those of the pure beta-glucan samples, both samples promoted the highest mean propionate production at 24 h. XOS resulted in a significant increase in the genus Bifidobacterium after 24 h of fermentation (0 h: 0.67 OTUs; 24 h: 5.22 OTUs; p = 0.038). Inulin and WholeFiber increased the beneficial genus Collinsella, consistent with findings in clinical studies. All analyzed compounds were fermentable and promoted the formation of beneficial SCFAs.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

Flax fiber appears as a suitable feedstock in the endeavor of deploying a sustainable biobased economy. Its environmental performance as reinforcement in composite materials has been studied in previous Life Cycle Assessments (LCAs). However, these studies only present a coarse Life cycle Inventory (LCI) and often fail to detail all processes of the supply chain or to represent the co-products. This paper aims to bridge this gap and provide data for future LCAs on flax fiber production and transformation.The study focuses on the impacts of producing a bio-based reinforcement material (a fabric product for non-aesthetic purposes) with a system expansion perspective. The functional unit is defined as the production of 2400 m² flax-based technical textile per year, this corresponds to one hectare of cultivated land. The geographical scope considers that the production occurs in France and that some manufacturing process are outsourced in China. A Sensitivity Analysis was carried out to assess the influence of the electricity mix in the various countries involved in the manufacturing cycle.A detailed life cycle inventory for flax fiber production and transformation was built and the environmental performance of a flax technical textile was assessed as a cradle-to-gate LCA. The fate of co-products was documented and was shown to contribute to the reduction of the generated environmental impacts. Through a cradle-to-gate LCA, a broader understanding of the environmental performance of a flax-based technical textile was presented by including the valorization of co-products and a wider set of analyzed impact categories, going therefore beyond the existing state-of-the-art. Results show agricultural activities and electricity production to be the biggest contributors to the environmental impacts of flax technical textile; contributions due to land use changes were minor in comparison. Very specifically for this case study, a sensibility analysis showed the influence of an all-French production to be more efficient from an environmental point of view.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

In the past few decades, the use of agricultural waste has been increasing due to the increasing demand for sustainable materials. This paper aims to review the significance of agricultural waste as a type of wealth and its potential as an alternative material in the composite field. It was found that many agricultural wastes had been utilized in various production of ecological products. The review discusses the physical, mechanical, and chemical properties of the natural fibers made from agricultural waste and the use of Pineapple Leaf Fiber Reinforced Composite to manufacture UAVs (Unmanned Aerial Vehicles). The extracted waste fibers’ physical, mechanical, and chemical properties show that these agricultural wastes can produce better advanced composite materials suitable for structural applications. The use of pineapple leaf fiber in Unmanned Aerial Vehicles manufacturing has the potential to revolutionize this industry and contribute to a more sustainable future.

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

Human-robot collaboration is a new trend in modern manufacture. The safety or human protection is of great significance due to the share of the same workshop between humans and robots. To achieve effective protection, in this paper, a contact force sensor based on the 8-shaped wound polymer optical fiber is proposed. The 8-shaped wound structure can convert the normal contact force to the shrinkage of the 8-shaped optical fiber ring. The macro-bending loss of the optical fiber is used to detect the contact force. Compared with conventional sensors, the proposed scheme has the advantage of high flexibility, low cost, fast response, high repeatability, which shows the great promise on actively alarming collision and passively reducing the hurt.

The dispersion properties of surface plasmon polaritons during propagation on metal wires with a dielectric coating in the terahertz frequency range are investigated theoretically. An analytical expression is obtained for a pulsed electric field from the solution of Maxwell equations taking into account high-order dispersion terms. The effect of the dielectric coating on the distortion of the pulse shape is analyzed. Unlike uncoated wire, the propagation of a surface plasmon pulses along a coated wire is highly dispersive. It is shown that the coating leads to the appearance of a long-chirped signal with a propagation of only a few millimeters, i.e. when a terahertz pulse propagates along a coated wire, it acquires a long oscillatory tail, the frequency of which depends on time.

This work presents first time successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow GeO2-doped ring core and strongly induced twisting up to 790 revolutions per meter. Some technological issues for manufacturing of GeO2-doped supporting elements for large hollow cores as well as described above complicated spun MOFs are discussed. We introduce some results of tests, performed for pilot samples of designed and manufactured described above untwisted and twisted MOFs with outer diameter 65 µm and hollow ring core inner diameter 30.5 µm under wall thickness 1.7 µm and refractive index difference n=0.030, including their geometrical parameters, basic transmission characteristics and measurements of far-field laser beam profile patterns.

An experimental study was carried out to evaluate the ductility of reinforced concrete beams longitudinally reinforced with hybrid FRP-Steel bars. The specimens were fourteen reinforced concrete beams with and without hybrid reinforcement. The test variables were bars position, the ratio of longitudinal reinforcement, and the type of FRP bars. The beams were loaded up to failure using a four-point bending test. The performance of the tested beams was observed using the load-deflection curve obtained from the test. Numerical analysis using the fiber element model was used to examine the growth of neutral axis depth due to the effect of test variables. The neutral axis curves were then used to further estimate the neutral axis angle and neutral axis displacement index. The test results show that the position of the reinforcement greatly influences the flexural behavior of the beam with hybrid reinforcement. It was observed from the test that the flexural capacity of beams with hybrid reinforcement is 4% to 50% higher than that of the beams with conventional steel bars depending on bars position and the ratio of longitudinal reinforcement. The ductility decreases as the hybrid reinforcement ratio (Af/As) increases. This study also showed that a numerical model developed can predict the flexural behavior of beams with hybrid reinforcement with reasonable accuracy.

The review aims to assess fifteen (15) academic literature sources, highlighting the application of machine learning algorithms in the maintenance operations of optical fiber networks. It exhibits the collection of data using PRISMA methodology—Preferred Reporting Item for Systems Review and Meta-Analyses. The application, results, and performance metrics are discussed based on the collected observations, computations, and statistics in the studies, which revealed records of high accuracy degrees ranging from 86% to 98% on average and quality ML models including Neural Networks (NNs), Support Vector Machines (SVMs), and LSTM, as well as deep learning models that disclosed effective results of determining challenges and problems within the optical fiber lines. The review mainly centralized on superior machine learning technologies that surpass traditional techniques in fault detection and localization for improved optical fiber networks’ operations while providing insights into the limitations and challenges encountered in real-world applications of these models, offering a comprehensive perspective on the optical fiber network’s domain.

The excellent properties of carbon fibers, in combination with the high price of carbon fibers, makes it interesting to recycle these fibers. Pyrolysis is already an established recycling method to recover the carbon fibers, but in this process also the sizing is removed which could result in lower mechanical properties because of bad adhesion between the fiber and matrix. In this study, recycled carbon nonwoven reinforcements made from pyrolyzed carbon fibers were pre-treated in order to improve the mechanical properties of recycled carbon polyamide and recycled carbon polypropylene composites. The pre-treatment involves applying a to the matrix adapted primer coating to the nonwoven by spraying. Via compression molding, polyamide and polypropylene composites were prepared with and without pretreatment. The tensile and interlaminar shear strength of these composites were measured to determine the effect of the pretreatment. Results revealed that both strengths could be increased by pretreatment of the carbon nonwoven and the increase was largest for the PP composites.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

In this study, experimental work was carried out on reinforced concrete (RC) beams strengthened with carbon fiber reinforced polymers (CFRP) plates. This study aims to examine the effect of the reinforcement ratio on the flexural behavior of these beams and propose a new model for predicting the debonding moment. Six RC beams consisting of three control beams and three beams strengthened with CFRP plates were tested. The beams were simply supported and loaded with four-point bending. The test variable was the tensile reinforcement ratio (1%, 1.5%, and 2.5%). Analytical prediction using the fiber element method was also carried out to obtain the complete theoretical response of the beam due to flexural loads. The test results show that the reinforcement ratio affected the bending performance of RC beams with CFRP plates. Following this, the experimental data from 60 beam test results from published literature and this study were analyzed. From these data, it was found that the ratio of tensile reinforcement, the ratio of modulus of elasticity of concrete, the modulus of elasticity of the plate, and plate thickness all affect the value of debonding moment. A parametric study using fiber element and two-dimensional finite element method was also carried out to confirm the effect of these parameters on debonding failure. These parameters were then used to develop an equation to predict the debonding moment of RC beams strengthened with CFRP plates using simple statistical analysis. This analysis resulted in a simple model for predicting the debonding moment. Then the model is entered into a computer program, and the complete response of the cross-section due to debonding failure can be obtained.

This study introduces a Fiber Specklegram Sensor (FSS) design for temperature measurement utilizing a single-multi-single mode optical fiber configuration. FSS technology offers unique advantages for potential development into portable sensing systems. This investigation explores an FSS design compatible with miniaturization by optimizing the interrogation system based on the relationship between speckle grain size and filtering fiber area. Temperature variations are detected through fluctuations in optical power at the sensor output, offering a simple and reduced interrogation scheme. The performance of the FSS is assessed through post-calibration measurements compared to a commercial Fiber Bragg Grating (FBG) sensor, demonstrating comparable results. These findings pave the way for compact and portable fiber optic temperature sensing systems leveraging FSS advantages while maintaining compatibility with established fiber optic measurements.

The study presents the synthesis and characterization of dual-layer sulfonated polyphenylenesulfone (SPPSu) nanocomposite hollow fiber nanofiltration membranes incorporating titanium dioxide (TiO2) nanoparticles using the phase inversion technique. The newly developed membranes were systematically characterized using advanced tools and methods to evaluate their properties and performance. The study focused on investigating the effects of TiO2 addition in the SPPSu inner layer on pure water permeability, and salt rejection. The nanocomposite hollow fiber nanofiltration membranes exhibited a significant enhancement in pure water permeability, with a three-fold increase compared to the pristine membranes, achieving a flux of 5.4 L/m2h.bar. The addition of TiO2 also led to an improvement in the mechanical properties of the membranes, as evidenced by the increase in the expected tensile strength from 2.4 to 3.9 MPa. To evaluate the salt rejection performance, rejection tests were conducted using a laboratory-scale filtration setup in recycle mode. Aqueous solutions containing different divalent ions, specifically magnesium sulfate (Mg2SO4) and sodium sulfate (Na2SO4) at a concentration of 500 ppm, were used as the feed solution. The modified dual-layer hollow fiber nanocomposite membranes exhibited a maximal rejection of 95% for Mg2SO4, demonstrating their effective separation capabilities for divalent ions. The findings of this study highlight the successful synthesis and characterization of dual-layer SPPSu nanocomposite hollow fiber nanofiltration membranes incorporating TiO2 nanoparticles. The incorporation of TiO2 resulted in improved pure water flux, mechanical strength, and salt rejection performance. These enhanced properties make the developed nanocomposite membranes promising candidates for applications in nanofiltration processes, particularly for the selective separation of divalent ions from aqueous solutions.

The distributed fiber optic strain measurement based on Rayleigh scattering has recently become increasingly popular in automotive or mechanical engineering for strain monitoring and in the construction industry, especially structural health monitoring. This technology enables the monitoring of strain along the entire fiber length. This article addresses integrating optical fibers of different coatings into the concrete matrix to measure the shrinkage deformations. However, previous studies do not give a clear statement about the strain transfer losses of fiber optic sensors in this application. In this context, three different coating types were investigated regarding their strain transfer. The fibers were integrated into fine-grained concrete prisms, and the shrinkage strain was compared with a precise dial gauge. The analysis shows a high correlation between the reference method and the fiber measurement, especially with the Ormocer coating. The used acrylate coating is also consistent in the middle area of the specimen but requires a certain strain introduction length to indicate the actual strain. The main result of this study is a recommendation for fiber coatings for shrinkage measurement in fine-grain concretes using the distributed fiber optic strain measurement. In addition, the advantages and disadvantages of the measurement method are presented.

To help reduce the impact of geohazards, an innovative landslide early-warning technology based on an energy demodulation-based fiber optic sensing (FOS-LW for short) technology, is introduced in this paper. FOS-LW measures the energy change in a sensing fiber at the segment of micro-bending, which can be caused by landslide movements, and automatically raises an alarm as soon as the measured signal intensity in the fiber reaches a pre-set threshold. Based on the sensing of micro-bending losses in the fiber optics, a two-event sensing algorithm has been developed for the landslide early-warning. The feasibility of the FOS-LW technology is verified through laboratory simulation and field tests. The result shows that FOS-LW has some unique features such as the graded alarm, real-time responses, remote monitoring, low cost and passive optical network, and can be applied in the early-warning of landslides.

We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

This work presents results of property researches of fabricated samples of silica few-mode optical fiber (FMF) with induced chirality under twisting 10 and 66 revolutions per meter, core diameter 11 µm, typical “telecommunication” cladding diameter 125 µm and improved height of quasi-step refractive index profile. Proposed FMF supports 4 guided modes over “C”-band. We represent results of computed characteristics, as well as experimentally measured spectral responses of laser-excited optical signals, including researches and analysis of few-mode effects, occurring after fiber Bragg grating writing.

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

This research aimed to determine the effect of alkaline treatment on zalacca midrib fiber (ZMF) concerning various aspects such as thermal stability, crystallinity index, interfacial bonding, interfacial shear strength, water absorption capacity, as well as conducting Scanning Electron Microscopy (SEM). This investigation extended to evaluating the mechanical properties of composites enriched with microcrystalline cellulose with prosthetic socket materials available on the market. Subsequently, ZMF was obtained by splitting and soaking zalacca midrib for 12 hours. Each of ZMF was removed from the midrib and soaked in 5% sodium hydroxide for 3, 6, 9, and 12 hours. The composite material was molded by mixing 10% microcrystalline cellulose with a rotational speed of 150 rpm, maintaining a temperature of 40°C, and continuing the mixing process for 30 minutes. As a result of the alkaline treatment, several positive effects were observed, including increased fiber density, improved particle bonding, increased thermal compatibility, and cleaner fiber surfaces, attributed to reduced levels of hemicellulose, lignin, pectin, and other impurities as confirmed by SEM analysis. The microcrystalline cellulose added to the composite increased the interfacial shear strength, and tensile strength increased by 56.74%, composite flexural strength increased by 76.43%. The SEM analysis results showed that the composite with ZMF on the base fiber broke during the tensile test because fiber experienced an increase in interfacial bonding between fiber and the matrix. The water absorption test showed that untreated fiber had a higher level of absorption

The purpose of this study was to analyze the influence of Chitosan 0.2% in various final cleaning methods on the bond strength of fiberglass post (FP) to intrarradicular dentin. Ninety bovine incisors were sectioned to obtain root remnants measuring 18 mm in length. The roots were divided: G1: EDTA 17%; G2: EDTA 17% + PUI; G3: EDTA 17% + EA; G4: EDTA 17% + XPF; G5: Chitosan 2%; G6: Chitosan 2% + PUI; G7: Chitosan 2% + EA; G8: Chitosan 2% +XPF. After carrying out the cleaning methods, the posts were installed, and the root cleaved to to generate two disks from each root third. Bond strength values (MPa) obtained from the micro push-out test data were assessed by Kruskal-Wallis and Dwass-Steel-Critchlow-Fligner tests for multiple comparisons (α = 5%). Differences were observed in the cervical third between G1 and G8 (p=0.038), G4 and G8 (p=0.003), G6 and G8 (p=0.049), and Control and G8 (p=0.019). The final cleaning method influenced the adhesion strength of cemented FP to intrarradicular dentin. Chitosan 0.2% + XPF positively influenced adhesion strength, with the highest values in the cervical third.

The calibration of length is related to the national economy and people's livelihood. The traditional calibration of length value was sent the uncalibrated instrument to the laboratory and the intrinsic error of the tested instrument was obtained in the laboratory. However, calibrating the instrument in the site produced additional error. In this article, a remote calibration method of length measurement based on optical fiber information transmission following with a proof of principle system was studied to reduce the additional error. The 1.0-level displacement guide rail was calibrated according to this method. The results showed that the relative error of guide rail displacement under different lengths was within 0.6%. The expanded uncertainties of 10 μm, 100 μm and 1 mm were analyzed respectively. The calibration results meet the actual standards of the guide rail. This optical method is a good candidate for remote calibration.

Fiber laser technology has been demonstrated as a versatile and reliable approach for laser source manufacturing with a wide range of applicability in various fields ranging from science to industry. The power/energy scaling of single fiber laser systems has faced several fundamental limitations. To overcome them and to boost the power/energy level even further, combining the output powers of multiple lasers has become the primary approach. Among various combining techniques, the coherent beam combining of fiber amplification channels is the most promising approach, instrumenting ultra-high power/energy lasers with near-diffraction-limited beam quality. This paper provides a comprehensive review of the progress of coherent beam combining for both continuous-wave and ultrafast fiber lasers. The concept of coherent beam combining from basic notions to specific details of methods, requirements, and challenges are discussed, along with reporting some practical architectures for both continuous and ultrafast fiber lasers.

In this study, Brillouin optical time-domain analysis (BOTDA) sensing technology was utilized for monitoring settlement in a similarity model of a highway subgrade. As contact winding cannot be used for an optical fiber that is buried directly in soil, uncoupling between. the fiber and the soil can occur. Thus, an optical-fiber-embedded beam (OFEB) was developed, and a method for measuring and calculating the beam deformation was proposed. A calibration test and a test on a similarity model of a subgrade were carried out to investigate the applicability and monitoring accuracy of the OFEB. It was concluded that the OFEB can accurately measure beam deflection, where the maximum relative error between measurements by the optical fiber and a displacement transducer was approximately 5%. The OFEB was embedded directly into a similarity model of a subgrade to monitor settlement. The deflection deformation of the OFEB was found to be close to the subgrade settlement over a certain settlement range with a relative error below 8.1%. Thus, the OFEB can be used to realize measure large-range distributed settlement in a subgrade. A numerical simulation was performed to identify appropriate beam dimensions and material design parameters, thereby extending the measurement range before decoupling of the OFEB and soil occurs. The enhancement of the measurement range and accuracy of the OFEB based on the preliminary experiments carried out in this study enables further investigation of settlement monitoring.

Machine learning (ML) methodologies have been looked upon recently as a potential candidate for mitigating nonlinearity issues in optical communications. In this paper, we experimentally demonstrate a 40-Gb/s 256-quadrature amplitude modulation (QAM) signal-based Radio over Fiber (RoF) system for 50 km of standard single mode fiber length which utilizes support vector machine (SVM) decision method to indicate an effective nonlinearity mitigation. The influence of different impairments in the system is evaluated that includes the influences of Mach-Zehnder Modulator nonlinearities, in-phase and quadrature phase skew of the modulator. By utilizing SVM, the results demonstrated in terms of bit error rate and eye linearity suggest that impairments are significantly reduced and licit input signal power span of 5dBs is enlarged to 15 dBs.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

In this paper, a sensitivity sensor of dual-core photonic crystal fiber (DC-PCF) filled with magnetic liquid is introduced and investigated by the finite element method (FEM). To regulate the energy coupling involving the two cores, the magnetic fluid is filled into the pore between the two cores. To adjust the coupling between the supermodes in the DC-PCF, the refractive index of the magnetic fluid-filled air hole may change due to the external magnetic field. This specifically created a magnetic fluid-filled DC-PCF, the magnetic fluid-filled hole is not used as the core for energy transmission, thus avoiding transmission loss. The dip wavelength and the magnetic field displayed an excellent linear connection between 80 and 260 Oe, depending on the numerical data. The detection sensitivity of the magnetic field reached 515.75 pm/Oe at a short fiber length of 482 m. The designed magnetic fluid-filled DC-PCF has high sensitivity and small volume and has great application prospects in medical and industrial field magnetic field detection.

The global textile sector, pivotal to economic development, significantly contributes to environmental degradation, prompting a shift towards sustainable raw material sources. Embracing circular economy principles, this industry is exploring the valorization of agricultural by-products. This study introduces an innovative approach to repurposing mango waste into valuable textile fibers, a byproduct of the fruit processing industry, predominantly generated during juice and jam production. The focus is on the lignocellulosic constituents of mango waste, specifically the peel, seed, and fibrous material, traditionally considered as refuse. Previous research has predominantly utilized mango peel in pectin extraction for food applications, whereas the potential of seed and fibrous content remains underexplored. This investigation endeavors to transform these fibrous by-products into high-value materials suitable for textile manufacturing. The process involved washing, drying, and comprehensive physicochemical characterization of mango fibers, emphasizing lignin quantification, revealing a composition of 12.2% lignin. An experimental design was employed to elucidate the impact of variables such as liquid-to-solid ratio, reaction duration, and sodium hydroxide concentration on lignin dissolution through alkaline hydrolysis. Optimal conditions—10% NaOH concentration, 30 mL/g liquid-to-solid ratio over six hours—achieved an 83% reduction in lignin content. The resulting fibers exhibited properties akin to conventional natural fibers, including a favorable aspect ratio indicative of their suitability for textile applications. A subsequent softening process using propylene glycol enhanced the fibers' spinability, producing a durable, textured fabric ideal for eco-conscious fashion applications, including bags, footwear, and accessories. This research demonstrates the feasibility of converting mango waste into a textile-worthy material and underscores the importance of waste revalorization in promoting sustainability within the circular economy framework.

The current study presents a computational fluid dynamics model designed to simulate the isolation of 2D graphene components from their dispersion using a microfiltration hollow fiber membrane unit. The model utilizes Navier-Stokes and mass conservation equations to predict the flow and concentration behaviors in the system, and it employs the resistance-in-series approach to couple the fouling of the non-exfoliated graphites in the dispersion to the model. Specifically, the model accounts for the effects of the concentration polarization and cake formation of the fouling component, resulting in the increment of the transmembrane pressure (TMP) of the system. Additionally, we assumed the wettability of polymeric membrane’s inner wall enhances upon fouling by the flat layered structure material, leading to the reduction of the transmemrabe pressure. This approach demosntrates accurate reproduction of the exceptional experimental TMP behavior corresponding to the fouling of the graphite.

Turbidity is an important water quality parameter, especially for drinking water. The ability to actively monitor the turbidity level in Drinking Water Distribution Systems is of critical importance to the safety and wellbeing of the public. Traditional turbidity monitoring methods involve manual collection of water samples at set locations and times followed by laboratory analysis, which are labor intensive and time consuming. Fiber-optic measurement permits real-time, in-situ turbidity monitoring. But the current technology is based on plastic fibers, which suffer from high optical attenuation and hence are unsuitable for large-scale remote monitoring. In this paper, we report the demonstration of a fiber-optic turbidity sensor based on multi-mode glass fibers. The system uses a single fiber to both deliver laser light into the water sample and collect the back-scattered light for detection. A balanced-detection scheme is utilized to remove the common-mode noise to enhance the turbidity sensitivity. Highly linear turbidity responses are obtained and a turbidity resolution as low as 0.1 NTU is achieved. The test unit is also shown to have excellent reproducibility against repeated measurements and good stability against temperature changes. Turbidity measurement in real environmental matrices such as tap water and pond water is also reported with an assessment of the impact of flow rate. This work demonstrates the feasibility of future large scale distributed fiber-optic turbidity monitoring networks.

Nonwovens made of recycled carbon fibers (rCF) and thermoplastic (TP) fibers have excellent economic and ecological potential. In contrast to new fibers, recycled carbon fibers are significantly cheaper and the CO2 footprint is mostly compensated by energy savings in the first product life cycle. The next step for this promising material is its industrial serial use. Therefore the process chain from fiber to composite material is analyzed. Initially rCF length at different positions during the carding process is measured. Thereafter the influence of the TP fibers onto processing, fiber shortening and mechanical properties is evaluated. At last several nonwovens with different TP fibers and fiber volume contents between 15 vol.-% and 30 vol.-% are produced, consolidated by hot pressing and tested by 4-point bending to determine the mechanical values. The fiber length reduction ranges from 20.6 % to 28.4 %. TP fibers cushion the rCF against mechanical stress but hold rCF fragments back due to their crimp. The resulting bending strength varies from 301 MPa to 405 MPa and the stiffness from 16.3 GPa to 30.1 GPa. Design recommendations for reduced fiber shortening are derived as well as material mixtures which offer better homogeneity and higher mechanical properties.

Optical fiber sensors have become a widely-used tool to perform life-long monitoring of large structures. Different set-ups of sensors can be used to obtain information at different scopes. In this paper, the application of a portable Brillouin optical time domain analysis sensor applied to reinforced concrete beams is presented. The sensor is made up of a single-mode optical fiber applied to the structure that enables the measurement of tensile and compressive axial strain along the beams. The fiber is embedded into a concrete casting and fixed along the reinforcement bars so that a complete correlation can be obtained regarding strain and displacements in linear and non-linear flexural response. The use of four sensing fibers positioned along the beam's length at different vertical positions makes it possible to read the strain variation within the cross-section. In accordance with Bernoulli’s hypothesis, this allows curvature diagrams to be obtained across the structure. The measured curvature is used to set up the moment–curvature relationship, which highlights the possibility of the sensor monitoring structures continuously in space and time.

The use of optical fibers is increasing in modern aircraft because it helps solve challenges of size, weight, communication, and reliability in new aircraft generation. This work describes a video and power transmission system using optical fibers (PoF) for in-flight entertainment (IFE) system application. We present the benefits and the limitations of this application, and we perform two practical experiments to demonstrate their performance. It used off-the-shelf devices in the experiments, such as one 15-W semiconductor laser operating at 808 nm, GaAs photovoltaic converters, optical transmitters and receivers, and video monitors. The power and video signals were transmitted using two 50-m multimode fibers. In addition, we proposed and tested two types of energy transformation units (ETU), which are responsible for supplying electrical energy to the IFE video monitor and the optical fiber receiver.

Carbon fiber insole (CFI), which is lightweight and stiff to reduce energy loss and help wearers perform better in sports, has recently been introduced. However, there are scarce reports on the effects of CFI on sports performance, muscle fatigue and wearing comfort. This study investigat-ed the short-term effects of CFI on sports performance, lower extremity muscle activity, and sub-jective comfort. Thirty young healthy males performed various sports tasks and treadmill runs with wearable sensors under two experimental insole conditions (benchmark insole as a baseline, CFI). The results showed that compared to the benchmark insole, CFI significantly improved sports performance in terms of power generation and agility. However, it activated more of the Tibialis Anterior and Gastrocnemius Medialis muscles and was perceived stiffer, and less com-fortable. These findings suggested that CFI can improve sports performance, but it could cause more lower extremity muscle fatigue and subjective discomfort.

In this paper, a novel pendulum-type accelerometer based on hetero-core fiber optics has been proposed for structural health monitoring targeting large-scale civil infrastructures. Vibration measurement is a non-destructive method for diagnosing the failure of structures by assessing natural frequencies and other vibration patterns. The hetero-core fiber optic sensor utilized in the proposed accelerometer can serve as a displacement sensor with robustness to temperature changes in addition to immunity to electromagnetic interference and chemical corrosions. Thus the hetero-core sensor inside the accelerometer measures applied acceleration by detecting the rotation of an internal pendulum. A series of experiments showed that the hetero-core fiber sensor linearly responded to the rotation angle of the pendulum ranging within ±5°, and furthermore the proposed accelerometer could reproduce the waveform of input vibration in a frequency band of several Hz order.

Three carbon-chain extension genes associated with fatty acid synthesis in cotton, namely GhKAR, GhHAD, and GhENR, play important roles in oil accumulation in cotton seeds. In the present study, these three genes were cloned and characterized. The expression patterns of GhKAR, GhHAD and GhENR in the high seed oil content cultivars 10H1007, 10H1014, and 10H1041 differed somewhat compared with those of 2074B with low seed oil content at different stages of seed development. GhKAR showed all three cultivars showed higher transcript levels than that of 2074B at 10, 40 and 45 DPA. The expression pattern of GhHAD showed a lower transcript level than that of 2074B at both 10 and 30 DPA but higher transcript level than that of 2074B at 40 DPA. GhENR showed a lower transcript level than that of 2074B at both 15 and 30 DPA. The highest transcript levels of GhKAR and GhENR were detected at 15 DPA in 10H1007, 10H1014, and 10H1041 compared with 2074B. From 5 to 45 days post anthesis (DPA) cotton seed, the oil content accumulated continuously in the developing seed. Oil accumulation reached the peak at 40 DPA to 45 DPA and slightly decreased in mature seed. In addition, GhKAR and GhENR showed different expression patterns in fiber and ovule development processes, in which they showed high expression levels at 20 DPA during fiber elongation stage, but their expression level peaked at 15 DPA during ovule development processes. These two genes showed the lowest expression levels at the late seed maturation stage, while GhHAD showed peak at 10 DPA of fiber development. Compared to 2074B, the oil contents of GhKAR and GhENR overexpression lines increased 1.05~1.08 folds. These results indicated that GhHAD, GhENR and GhKAR were involved in both seed oil synthesis and fiber elongation with dual biological functions in cotton.

During carbonation process, the presence of water is an important parameter to accelerate this phenomenon. The carbon dioxide (CO₂) has been used as curing process production of fiber cement boards keeping the dimensional stability of cellulose fibers in cementitious matrix and promoting the CO₂ capture of environment. In addition, magnesium oxysulfate (MOS) cement has been used as another alternative binder to reduce the amount of CO₂ in the nature. The aim of this scientific paper is analysis the effect of rehydration method on the physical-mechanical properties of CO2-cured magnesium-based fiber cement boards. These boards were produced by Hatschek process simulation. The physical-mechanical performance and microstructural characteristics of MOS boards before and after carbonation were investigated by: water absorption (WA), apparent porosity (AP), and bulk density (BD); four-point bending test; X-ray diffraction (XRD); thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). According to the results, it was possible observe which the accelerated carbonation process resulted in improvements in the mechanical properties of the boards. The boards carbonated after 48 hours showed higher Modulus of Rupture values. The rehydration process of the composites before carbonation led to enhancements in the boards pre-cured for 48 and 72 hours, demonstrating that carbonation occurred more effectively after the supply of water through rehydration. The improvements in mechanical properties were associated with the formation of hydration products, which preferentially formed in the pores and voids of the fiber-cement. The presence of these carbonation products altered the physical properties of the materials, increasing the density of the boards and reducing the void volume. The decomposition of the formed carbonates was confirmed by thermogravimetric analysis, which indicated that the rehydration process favored the carbonation of the materials

For a fiber optic gyroscope, thermal deformation of the fiber coil can introduce additional ther-mal-induced phase errors, commonly referred to as thermal errors. Thermal error compensation techniques are effective means of addressing this issue. The principle behind these techniques involves real-time sensing of thermal errors and correcting them within the output signal. Since it is challenging to directly separate thermal errors from the output signal of the fiber optic gyro-scope, it is necessary to predict thermal errors based on temperature. To establish a mathematical model between temperature and thermal errors, this paper measured synchronized data of phase errors and angular velocity for the fiber coil under different temperature conditions and aimed to model it using data-driven methods. Due to the difficulty of conducting tests and the limited number of data samples, an algorithm called TD-model modeling is proposed to address the issue of overfitting, which can reduce the model's generalization ability. First, a theoretical analysis of the phase errors caused by thermal deformation of the fiber coil is performed. Subsequently, the critical parameters, such as the thermal expansion coefficient, are determined, and a theoretical model is established. Finally, the theoretical analysis model is incorporated as a regularization term and combined with the test data to jointly participate in the regression of model coefficients. Through experimental comparative analysis, it is shown that, relative to ordinary regression models, the TD-model effectively mitigates overfitting caused by the limited number of samples, leading to a 58% improvement in predictive accuracy.

Traditional lithium-ion batteries cannot meet the high flexibility and bendability requirements of modern flexible electronic devices due to the limitations of their electrode materials. Therefore, the development of high-performance flexible energy storage devices is of great significance for promoting flexible electronics. In recent years, one-dimensional flexible fiber lithium-ion batteries have been rapidly developed due to the advantages of high flexibility and bendability. However, it is still a big challenge to realize 1D flexible fiber lithium-ion batteries with excellent electro-chemical properties and good mechanical performance. In this work, a reduced graphene ox-ide-based printing ink is proposed to fabricate flexible Li4Ti5O12/graphene fiber electrodes through a 3D printing assembly strategy. It is noteworthy that the green reducing agent vitamin C was used to reduce graphene oxide in one step, which improved the conductivity of the fiber elec-trode. Furthermore, a 3D conductive network is constructed inside the fiber electrodes due to the high specific surface area of reduced graphene oxide, which enhances the electronic conductivity and ion mobility. The fiber electrode not only has good mechanical performance, but also has ex-cellent electrochemical properties. Equally important, the method is simple and efficient, and the working environment is flexible. It can precisely control the shape, size and structure of the one-dimensional fiber flexible electrode, which is of great significance for the development of fu-ture flexible electronic devices.

The work presents an approach to instrument the load sensing bearings for automotive applications for estimation of the loads acting on the wheels. The system comprises fiber-optic sensors based on addressed fiber Bragg structures (AFBS) with two symmetrical phase shifts. A mathematical model for load-deformation relation is presented, and the AFBS interrogation principle is described. The simulation includes (i) modeling of vehicle dynamics in a split-mu braking test, during which the longitudinal wheel loads are obtained, (ii) the subsequent estimation of bearing outer ring deformation using a beam model with simply supported boundary conditions, (iii) the conversion of strain into central wavelength shift of AFBS, and (iv) modeling of the beating signal at the photodetector. The simulation results show that the estimation error of the longitudinal wheel force from the strain data acquired from a single measurement point was 5.44% with root-mean-square error of 113.64 N. A prototype load sensing bearing was instrumented with a single AFBS sensor and mounted in a front right wheel hub of an experimental vehicle. The experimental setup demonstrated comparable results with the simulation during the braking test. The proposed system with load-sensing bearings is aimed at estimation of the loads acting on the wheels, which serve as input parameters for active safety systems, such as automatic braking, adaptive cruise control, or fully automated driving, in order to enhance their effectiveness and safety of the vehicle.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

In this study, a carbon fiber microelectrode (CF) was applied for the investigation of electrochemical behavior and determination of natural antioxidant, apocynin (APO). Given the limited solubility of APO in water, a mixture of anhydrous acetic acid (AcH) with 20%, v/v acetonitrile (AN) and 0.1 mol L-1 sodium acetate (AcNa) was used. The electrochemical properties of APO were examined through linear sweep voltammetry (LSV), differential pulse voltammetry (DPV), and cyclic voltammetry (CV). The anodic oxidation of APO, which is the basis of the method used, proved to be diffusion-controlled and proceeded with a two-electron and one proton exchange. Both radicals and radical cations, arising from the first and second step of electrode reactions, respectively, underwent subsequent chemical transformations to yield more stable final products (EqCiEiCi mechanism). Using optimized DPV conditions, the anodic peak current of APO at potential of 0.925 V vs Ag/AgCl showed a good linear response within the concentration range of 2.7×10-6 – 2.6×10-4 mol L-1. The detection and quantification limits were determined as 8.9×10-7 and 2.7×10-6 mol L-1, respectively. The developed DPV method enabled the successful determination of APO in herbal extracts and in dietary supplements. It should be noted that this is the first method of voltammetric determination of APO.

Visible light communication (VLC) can offer the advantages of license and electromagnetic interference (EMI) free wireless transmission. As optical signal does not interference with the radio-frequency (RF) signal, VLC can be used to augment RF wireless communication to provide extra communication capacity while without degrading the performance of both signals. In order to achieve high performance VLC transmission, optical alignment between the optical transmit (Tx) and receiver (Rx) is very critical to enhance the received signal-to-noise ratio (SNR). Optical beam-steering at the Tx can be utilized to ensure narrow optical beam can reach the Rx; however, complicated and active tracking are required. Lenses or compound parabolic concentrators (CPCs) can be install in front of the Rx for focusing to enhance the SNR. However, these will limit the Rx field-of-view (FOV) and making the VLC transmission more subjected to misalignment issue. Hence, many creative optical antennas have been proposed and demonstrated using special optical materials as well as special Rx to enhance the FOV of VLC systems. However, they have their limitations, such as data rates and FOVs. In this work, we put forward and demonstrate a bi-direction free-space VLC system supporting multiple moveable Rxs using a light-diffusing optical fiber (LDOF). The downlink (DL) signal is launched from an head-end or central office (CO) far away to the LDOF at the client side via a free-space transmission. When the DL signal is launched to the LDOF, which acts as an optical antenna to re-transmit the DL signal to different moveable Rxs. The uplink (UL) signal is sent via the LDOF towards the CO. In a proof-of-concept demonstration, the LDOF is 100 cm long and the free space VLC transmission between the CO and the LDOF is 100 cm. 210 Mbit/s DL and 850 Mbit/s UL transmissions, meeting the pre-forward-error-correction bit error rate (pre-FEC BER = 3.8 × 10−3) threshold are achieved.

The formation of a rigid tough interface based on a nacre-like structure in carbon fiber (CF) composites is a promising way to eliminate low delamination resistance. An effective method of coating CFs is electrophoretic deposition (EPD), which, in the case of dissimilar components like graphene oxide (GO) and polymeric glue, usually requires their chemical bonding/ strong interactions. In this work, we focus on chitin nanocrystals (ChNCs), leading to an excellent mechanical performance of artificial nacre, where favorable interactions and bonding with GO were controlled by degrees of deacetylation (5, 15 and 30 %). We have prepared coatings based on GO/ChNCs adducts with 95/5, 90/10,50/50 and 25/75 ratios using optimized EPD conditions (pH, concentration, voltage and time). The prepared materials were characterized using FTIR, TEM, XPS, SEM, DLS, and XRD. SEM evaluation indicates the formation of a homogeneous interlayer, which possesses a fair ability of chemical bonding with the epoxy matrix. Short beam testing of epoxy matrix composites indicates that coating does not decrease stiffness and its relatively low dependence on composition. Therefore, all coatings are promising for a detailed study of delamination resistance using laminate samples. Moreover, facile EPD from water solution/ suspension has a fair potential for industrial applications.

A comprehensive model for designing robust all-in-fiber microresonator-based optical sensing setups is illustrated. The investigated all-in-fiber setups allow light to selectively excite high-Q whispering gallery modes (WGMs) into optical microresonators, thanks to a pair of identical long period gratings (LPGs) written in the same optical fiber. Microspheres and microbubbles are used as microresonators and evanescently side-coupled to a thick fiber taper, with a waist diameter of about 18 µm, in-between the two LPGs. The model is validated by comparing the simulated results with the experimental data. A good agreement between the simulated and experimental results is obtained. As an application example, the sensing of the concentration of an aqueous glycerol solution is demonstrated. The model is general and by exploiting the refractive index and/or absorption characteristics at suitable wavelengths, the sensing of other substances or pollutants can be also predicted.

One-dimensional shape memory polymer fibers (SMPFs) have obvious advantages in mechanical properties, dispersion properties and weavability. In this work, a method for fabricating semi-crystallization ethylene-vinyl acetate copolymer (EVA) fiber with two-way shape memory effect by melt spinning and ultraviolet (UV) curing was developed. Here, the effect of crosslink density on its performance was systematically analyzed by gel fraction measurement, tensile tests, DSC and TMA analysis. The results showed that the crosslink density and shape memory properties of EVA fiber could be facilely adjusted by controlling UV curing time. The resulting EVA fiber with cylindrical structure had a diameter of 247.13 ± 10.07 μm, and its mechanical strength and elongation at break were 64.46 MPa and 114.33%, respectively. The critical impact of the crosslink density and applied constant stress on the two-way shape memory effect were analyzed. Moreover, the single EVA fiber could lift more than 143 times its own weight and achieve 9% reversible actuation strain. The reversible actuation capability was significantly enhanced by a simple winding design of the single EVA fiber, which provided great potential applications in smart textiles, flexible actuators and artificial muscles.

Cytochrome P450 (CYPs) is a functionally diversified third-largest gene family that exploded in the plant kingdom. Their role in different organ development has been illustrated by the intervention of phytohormone. Cotton is a model organism for cell differentiation and cell elongation. To decipher the participation of CYPs in different cotton fiber developmental stages, we identified and characterized 2460 CYPs in three diploids and two allotetraploid cottons. Furthermore, In-silico expression and cluster analysis of cotton CYPs was conducted to distinguish the fiber stage-specific clusters that have the determining role in different stages of fiber development. The subgenome expression of two conserved Gossypium hirsutum CYPs, namely, GhCYP78A197 and GhCYP78A198 contributed to fiber initiation at an early stage of fiber development, governed by the co-occurrence of TATA and MYB TFs binding sites. Coexpression network partners of these two GhCYP78A annotated as auxin, kinases, chromatin remodeler, epigenetic regulator and cyclin-related genes that possibly induce the endoreduplication and cell proliferation for fiber cell initiation to define the high yield and biomass.

Expansive soil shows dual swell-shrink which is not suitable for the construction. Several mitigating techniques exist to counteract the problem promulgate by expansive clayey soils. This paper explored the penitential mecho-chemical reinforcement of expansive clayey soil to mitigate the effect of upward swelling pressure and heave. The polypropylene fiber is randomly distributed in the soil for mechanical stabilization, and the industrial residual silica fume is used as a chemical stabilizer. The experimental analysis is made in three phases which involved the tests on mechanical reinforced expansive soil using randomly distributed polypropylene fibers with different percentages (0.25%, 0.50%, and 1.00%), and 12mm length. The second phase of experiments carried out on chemical stabilized expansive soil with different percentages (2%, 4% and 8%) of silica and next phase of the experimental focused in the combination of mecho-chemical stabilization of the expansive soil with different combination of silica (i.e., 2%, 4% and 8%) and polypropylene fibers (i.e., 0.25%, 0.50% and 1.00%). Maximum dry density (MDD), optimum moisture content (OMC), liquid limit (LL), plastic limit (PL), plastic index (PI) grain size, and constant volume swelling pressure test were performed on unreinforced and reinforced expansive soil to investigate the effect of polypropylene fiber and silica fume on the engineering properties of expansive clayey soil. The experimental results illustrate that the inclusion of polypropylene fiber has a significant effect on the upward swelling pressure and expansion property of expansive soil. The reduction in the upward swelling pressure and expansion is a function of fiber content. These results also indicated that the use of silica fume caused a reduction in upward swelling potential, and its effect was considerably more than the influence of fiber.

The effect of γ-ray irradiation on surface plasmon resonance (SPR) sensing capability of refractive index (n = 1.418–1.448) of the silica glass optical fiber comprised of germano-silicate glass cladding embedded with Au nano-particles (NPs) was investigated. As the γ-ray irradiation increased from 1 hour to 3 hours with the dose rate of 1,190 Gy/h, the morphology of the Au NPs and the SPR spectrum were found to change. The average diameter of Au NPs increased with the aspect ratio from 1 to 2 and the nano-particles became grown to the clusters. The SPR peak wavelength shifted towards longer wavelength with the increase of total dose of γ-ray irradiation regardless of the corresponding refractive indices. The SPR sensitivities (wavelength/refractive index unit, nm/RIU) also increased from 407 nm/RIU to 3,553 nm/RIU, 1,483 nm/RIU, and 2,335 nm/RIU after the γ-ray irradiation at the total dose of 1,190 Gy, 2,380 Gy, and 3,570 Gy, respectively.

This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.

A novel fiber optic sensing technology for high frequency dynamics detection is proposed in this paper, specifically tailored for structural health monitoring applications based on strain wave analysis, including both passive impact identification and active Lamb wave monitoring. The sensing solution relies on a fiber optic-based interferometric architecture associated to an innovative coherent detection scheme, which retrieves in a completely passive way the high-frequency phase information of the received optical signal. The optical fiber can be arranged into different configurations in order to meet the requirement of the specific application, the sensor sensitivity being maximized while still ensuring a limited gauge length if a local measure is required. For the active Lamb wave monitoring, this results in a sensing fiber arranged in multiple loops glued on an aluminum thin panel in order to increase the phase signal relative only to the sensing points of interest. Instead, for passive impact identification, the sensitivity is simply increased by exploiting a longer gauge length glued to the structure. The fiber optic coherent (FOC) sensor detects the strain waves emitted by a piezoelectric transducer placed on the aluminum panel or generated by an impulse hammer, respectively. The FOC sensor measurements have been compared with both a numerical model based on Finite Elements and traditional piezoelectric sensors, confirming a very good agreement between experimental and simulated results for both the active and passive impact monitoring scenarios.

With a view to sustainable development and circular economy, this work focused on the possibility to valorize a secondary waste stream of recycled carbon fiber (rCF) to produce a 3D printing usable material with PA6,6 polymer matrix. The reinforcing fibers implemented in the present research are the result of a double recovery action: starting with pyrolysis from which long fibers are obtained, used to produce non-woven fabrics and, subsequently, fiber agglomerate wastes obtained from this last process are ground in a ball mill. The effect of a different amount of reinforcement at 5% and 10% by weight on the mechanical properties of 3D printed thermoplastic composites was investigated. Although the recycled fraction was successfully integrated in the production of filaments for 3D printing and therefore in the production of specimens via Fused Deposition Modeling technique, the results showed that fibers did not improve the mechanical properties as expected, due to an unsuitable average size distribution and the presence of a predominant dusty fraction ascribed to the non-optimized ball milling process. PA6,6 + 10 wt.% rCF composites exhibited a tensile strength of 59.53 MPa and a tensile modulus of 2.24 GPa, which correspond to an improvement in mechanical behavior of 21 5 % and 5 21 % compared to the neat PA6,6 specimens, respectively. The printed composite specimens loaded with the lowest content of rCF provided the greatest improvement in strength (+ 9% over the neat sample). Then, a prediction of the “optimum” critical length of carbon fibers was proposed that could be used for future optimizations of the recycled fiber processing.

Due to the renewed variation in government and political systems inside and outside countries, and with the high tariffs at borders, the latter have become an outlet for terrorism and smugglers. Therefore, each country seeks to develop its own protection system, and the technologies used in these systems vary according to the severity and the importance of the installations to be protected, it is found that some of them are expensive and unnecessary, but other have good and variable levels of efficiency. Consequently, the idea of designing a surveillance system that can monitor and control access becomes indispensable. In the same context, this work is of crucial strategic and geopolitical importance. It combines pre-existing alarm and monitoring methods and revolutionary Internet of Things (IoT) application products, of which Wireless Sensor Networks (WSN) and Optical Fiber Sensors (OFS) are part of this application. This article presents the distribution of wireless radar nodes accompanying with a Bragg fiber sensor to identify each rolling intruder incoming the zone to be monitored, from the determination of its speed, weight and wheelbase distance.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

Luminescent carbon dots (CDs) were locally synthesized in the core of CYTOP fibers using IR femtosecond laser direct writing (FLDW), a one-step simple method serving as a post-treatment of the genuine fiber. This approach enables the creation of several types of modifications such as ellipsoid voids. The CDs and photoluminescence (PL) distribute at the periphery of the voids. The PL spectral properties were studied through Excitation Emission Matrix in the visible range and excitation/emission spectrum in UV/visible range. Our finding reveals the presence of at least 3 distinct luminescent species, facilitating a broad excitation range extending from UV to green, and light emission spanning from blue to red. The average laser power and dose influence the quantity and ratio of these luminescent CD species. Additionally, we measured the spatially resolved lifetime of the luminescence during and after the irradiation. We found longer lifetimes at the periphery of the laser-induced modified regions and shorter ones closer to the center, with a dominant lifetime ~ 2ns. Notably, unlike many other luminophores, these laser-induced CDs are insensitive to oxygen, enhancing their potential for display or data storage applications.

In this investigation dyeing of alginate fiber was carried out after cationic treatment of EPTAC (2, 3-Epoxypropyl Trimethyl Ammonium Chloride). Optimum dyeing process and parameter show good dyeing performance when alginate fiber dyed with rhubarb dye. In addition to cationic treatment is taken into account for alginate fiber to improve fastness, color strength, breaking strength. Later in dyeing for fixation ferrous sulfate, copper sulphate was considered as mordents. Moreover using pre-mordanting methods conveyed the dyeing of alginate fiber with the stave of metallic mordant and without metallic salt mordents. The evaluation of each color dyed material was done through following two terms for instance CIELAB (L*, a*, and b*) and K/S values. According to AATCC test methods color fastness to washing of the dyed fiber was determined whereas according to the ASTM D3822M standard the breaking strength of alginate fiber was estimated and tested. When dyeing was carried out on alginate fiber through considering optimum parameter like 80◦C for 90 min, M: L 1:40 and at pH 7 which showed optimum results. In addition to mostly very good wash fastness was obtained while there was no fading of the color, whereas the moderate level of color fastness to crocking was achieved. Later after dyeing the evaluations of SEM of the cationized alginate fiber and FTIR of powder from the rhubarb dye were observed. The results suggested that the surface of cationized alginate fiber was smoother than the raw alginate fiber.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

Residual stresses in fiber metal laminates (FML) inevitably develop during the manufacturing process. The main contributor to these stresses is the difference in the coefficients of thermal expansion (CTE) between fibers and metal in combination with high process temperatures. To quantify these stresses, the use of specimens with an asymmetric layup is an easily adaptable method. The curvature that develops after the manufacturing of flat laminates with an asymmetrical layer stack is a measure of the level of residual stresses evolving during cure. However, the accuracy of the curvature evaluation is highly dependent on specimen design and other influencing parameters. In this work a large set of FML specimens is investigated to identify relevant influencing parameters and derive conclusions about specimen design and evaluation techniques. For certain layups and process parameters, there is a good correlation between the curvature and the stress-free temperature, which is further covered by analytical solutions for bimetals. This correlation is the basis to transfer curvature into a stress-free temperature that can consequently be used for the quantification of residual stress levels in more complex FMLs. The transfer is validated by in-situ strain measurements during cure using a strain gage technique. Based on the results, the application of asymmetric specimens for residual stress characterization in more complex laminates is presented in the form of a workflow.

The purpose of this study was to conduct a meta-analysis that shows the influence of fiber on ultimate compressive strength and tensile strength of ultra-high performance concrete. The internet scholarly search engines and ScienceDirect article references were used to illustrate the papers concerning the experimental investigations of mechanical properties of ultra-high strength concrete with and without fiber with clearly, completely and comparative raw data. The normal concrete test results were dismissed from this search. Seven trials were identified based on the adopted inclusion and exclusion criteria above. The meta-analysis based on standardized mean difference was carried out on the basis of a fixed-effects model for the major outcomes of the ultimate compressive and tensile properties of ultra-high performance concrete. A total of 888 test specimens were enrolled in these seven trials. The combined analysis yielded a sign of a significant improvement in ultimate compressive strength and tensile strength of ultra-high strength concrete with fiber addition of 2% by concrete volume. The summary effect size of ultimate compressive strength was 2.34 while a more improvement in term of tensile strength with effect size of 2.64. By addition fiber of 2% provides a significant benefit in mechanical properties of ultra-high performance concrete.

In order to reduce the waste of Akebia trifoliata peel and maximize its utilization. In this study, on the basis of single factor experiment and response surface method, the optimum technological conditions for the extraction of soluble dietary fiber from Akebia trifoliata peel by compound en-zyme method were obtained. The chemical composition, physical and chemical properties, structural characterization and biological activity of the purified soluble dietary fiber (AP-SDF) from the Akebia trifoliata peel were analyzed. We discovered that that the optimum yield was 20.87 % under the conditions of cellulase addition 600 U/g, enzymolysis time 100 min, solid-liquid ratio 1:24 g/mL and enzymolysis temperature 51 °C. At the same time, AP-SDF was a po-rous network structure cellulose type I acidic polysaccharose mainly composed of arabinoxylan (36.03%), galacturonic acid (27.40%) and glucose (19.00%), which possessed the structural charac-teristic peaks of the infrared spectra of polysaccharides, and the weight average molecular weight (Mw) was 95.52 kDa with good uniformity. In addition, AP-SDF exhibited high oil hold-ing capacity (15.11 g/g), good water holding capacity, swelling capacity, certain antioxidant ca-pacity in vitro, hypoglycemic activity in vitro of α-glucosidase inhibition and hypolipidemic ac-tivity in vitro of the binding ability of bile acids and cholesterol. These results will provide a theoretical basis for the development of functional products with antioxidant, hypoglycemic and hypolipidemic effects, it has certain application value in related industries.

In this paper, an all-fiber Mach-Zehnder interferometer (MZI) sensor for refractive index (RI) measuring is presented, which is based on Multimode–Single-mode–Multimode (MSM) fiber. The effects of both reducing the radius of the sensing part and the surface plasmon resonance (SPR) on its efficiency are investigated. Increasing the interaction of high-order modes with external media, caused by etching the cladding layer of the single-mode fiber part, significantly improves the sensitivity. Both wavelength and intensity interrogation approaches are employed to study the Multimode–etched Single-mode–Multimode (MESM) fiber sensor. The intensity and the wavelength sensitivities for the RI measurement in the range of 1.428-1.458 are obtained as -2308.92 %/RIU and 1313.14 nm/RIU, respectively. Finally, the MESM-SPR sensor is proposed and characterized. Results exhibit high performance in the RI range of 1.333 to 1.357, in which the sensitivity of 1433 nm/RIU is achieved. The advantages like low cost, high sensitivity, and simple fabrication methods make these sensors promising devices for chemical, food industry, and biosensing applications.

The gut microbiota plays a crucial role in childhood obesity, and diet is a dominating driver. The effects of fructo-oligosaccharides (FOS), as a dietary fiber, on the composition and metabolism of gut microbiota in healthy children was investigated by vitro fermentation system with a reformative YCFA medium (rich in tryptic hydrolysates of meat). The 16S rRNA sequencing technology was utilized to analyze the varieties of gut microbiota. Measurement of short chain fatty acids (SCFAs) and gases were used by the gas chromatograph. Majorbio Cloud Platform and MetOrigin, as the interactive cloud server, perform the microbiota analysis, the metabolic pathway enrichment analysis, the statistical correlations, and biological relationships using network visualization. We found that the FOS group significantly regulated the composition and metabolism of gut microbiota. The co-metabolism network showed that 3 metabolites were related to 6 differential bacteria and 8 metabolism pathways. These findings suggest that dietary fiber could regulate the composition of gut microbiota and its metabolites in a better direction, but when dietary fiber participates in precision nutrition formula, it may be relevant for precision obesity, may help identify windows of opportunity for the dietary intervention of childhood obesity.

Upcycling recycled carbon fibers recovered from waste carbon composites can reduce the price of carbon fibers while improving disposal-related environmental problems. This study assessed and characterized recycled carbon fibers subjected to sizing treatment using N-(2-aminoethyl)-3-aminopropyltrimethoxysilane (APS) chemically coordinated with polyamide 6 (PA6) and polypropylene (PP) resins. Sizing treatment with 1 wt.% APS for 10 s yielded O=C-O on the surface of the carbon fiber, and the -SiOH in the APS underwent a dehydration-condensation reaction that converted O=C-O (lactone groups) into bonds of C-O (hydroxyl groups) and C=O (carbonyl groups). The effects of C-O and C=O on the interfacial bonding force increased to a maximum, resulting in an oxygen-to-carbon ratio (O/C) of 0.26. The polar/surface energy ratio showed the highest value of 32.29% at 10 s, and the interfacial bonding force showed the maximum value of 32 MPa at 10 s, which is about 15% better than that of commercial carbon fiber (PA6-based condition). In 10-s resizing treatments with 0.5 wt.% 3-methacryloxypropyltrimethoxysilane (MPS), C-O, C=O, and O=C-O underwent a dehydration-condensation reaction with -SiOH, which broke the bonds between carbon and oxygen and introduced a methacrylate group (H2C=C(CH3)CO2H), resulting in a significant increase in C-O and C=O, with an O/C of 0.51. The polar/surface free energy ratio was about 38% at 10 s, with the interfacial bonding force increasing to 27% compared to commercial carbon fiber (PP-based conditions). The MPS exhibited a superior interfacial shear strength improvement, two times higher than that of APS, with excellent coordination with PP resin and commercial carbon fiber, although the interfacial bonding strength of the PP resin was significantly lower.

Fiber-based flexible sensors have promising applications potential in human motion and healthcare monitoring, owing to their merits of lightweight, flexibility, and easy processing. Now, high-performance elastic fiber-based strain sensors with high sensitivity, large working range and excellent durability are in great demand. Herein, we have easily and quickly prepared a highly-sensitive, durable fiber-based strain sensor by dip-coating of highly-stretchable polyurethane (PU) elastic fiber in MXene/ waterborne polyurethane (WPU) dispersion solution. Benefiting from the electrostatic repulsion force between the negatively charged WPU and MXene sheets in the mixed solution, very homogeneous and stable MXene/WPU dispersion was successfully obtained and the interconnected conducting networks were correspondingly formed in coated MXene/WPU shell layer, which makes as-prepared strain sensor exhibit a gauge factor of over 960, a large sensing range of over 90% and detection limit as low as 0.5% strain. As elastic fiber and mixed solution have the same polymer constitute, tight bonding of MXene/WPU conductive composite on PU fibers was achieved, enabling the as-prepared strain sensor endure over 2500 stretching-releasing cycles and thus show good durability. Full-scale human motion detection was also performed by the strain sensor, and a body posture monitoring, analysis, and correction prototype system was developed via embedding the fiber-based strain sensors into sweater, strongly indicating the great application prospect in exercise, sports and healthcare.

In the realm of power delivery to end-users, transformers are indispensable, with their malfunctions leading to substantial economic, safety, and environmental repercussions. The need for persistent surveillance is accentuated for in-situ oil-filled transformers, given the potential degradation of oil and the emergence of related ageing by-products. As the focus tilts towards online detection methodologies for transformer oil ageing, bypassing challenges associated with traditional offline methods such as sample contamination and misinterpretation, fiber optic sensors are gaining trac-tion due to their compact nature, cost-effectiveness, and resilience to electromagnetic disturbances typical in high-voltage environments. This work delves into the sensitivity analysis of intensi-ty-modulated plastic optical fiber sensors. The investigation encompasses key determinants such as the influence of optical source wavelengths, noise response dynamics, ramifications of varying sensing lengths, and repeatability assessments. Findings underscore that elongating the sensing length detrimentally affects both the linearity response and repeatability, largely attributed to the diminished resistance to external noise. Additionally, the choice of the optical source wavelength proved to be a critical variable in assessing sensor sensitivity.

This study investigated the effects of three oil production methods on the physicochemical properties of dietary fiber from rice bran flour, and the hypolipidemic effects of the dietary fibers were investigated in vitro and in vivo. The particle size results showed that the organic solvent-impregnated rice bran meal dietary fiber (N-RBDF) had the smallest average particle size and the aqueous enzymatic rice bran meal dietary fiber (E-RBDF) had the narrowest particle size distribution. Scanning electron microscopy (SEM) results demonstrated that all three kinds of rice bran meal dietary fibers (RBDF) were irregularly flaky. Fourier transform infrared spectroscopy (FT-IR) results revealed that the three RBDFs had similar reactive groups, and X-ray diffraction (XRD) results indicated that all three RBDFs were cellulose type I crystals. The results of thermogravimetric analysis showed that the lignin content of N-RBDF was significantly lower than that of the other two. Among the three kinds of RBDFs, E-RBDF had higher water retention capacity, swelling capacity, oil holding capacity, and adsorption capacity for cholesterol and sodium bile salts. The results of experimental studies in hyperlipidemic rats showed that all three kinds of RBDFs significantly reduced triglycerides (TG), total cholesterol (TC) and low-density lipoprotein cholesterol (LDL-C) and elevated high-density lipoprotein cholesterol (HDL-C) in serum of hyperlipidemic rats; they also significantly lowered malondialdehyde (MDA) and elevated total superoxide dismutase (T-SOD) and glutathione peroxidase (GSH-Px) activities in liver of rats. In addition, all three kinds of RBDFs decreased aminotransferase (ALT) and aminotransferase (AST) activity in serum and also improved liver steatosis and reduced atherosclerosis index (AI) in rats with hyperlipidemia. Our study provides a reference for the development and utilization of rice bran meal and the application of rice bran meal dietary fiber in food processing.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

We present an innovative method harnessing multistability within a diode-pumped erbium-doped fiber laser to construct logic gates. Our approach involves manipulating the intensity of external noise to regulate the probability of transitioning among four concurrent attractors. In this manner, we facilitate the realization of OR, AND, NOT, and NOR logic operations, aligning with the coexisting period-1, period-3, period-4, and period-5 orbits. Employing detrended fluctuation analysis, we establish equilibrium in the probability distributions of these states. The obtained results denote a substantial advancement in the field of optical logic gate development, representing a pivotal stride toward the seamless integration of an all-optical logic gate within laser oscillator-based systems.

Fiber coupling efficiency is one of the key technical indicators of atmospheric laser communication, which directly affects the communication system BER. According to the optical fiber coupling efficiency model, the optical fiber coupling model under atmospheric slant link is established, and the relationship between wavelength, zenith angle, receiving aperture, altitude and coupling efficiency is studied through numerical simulation. Based on the principle of adaptive optics turbulence correction, the relationship between fiber coupling efficiency and adaptive optics order is established. A fast method for estimating the coupling efficiency based on Strehl ratio is proposed. According to the principle of laser communication system, the semi-physical simulation experimental system of atmospheric slant-range channel coupling efficiency is constructed, and the coupling efficiency test and analysis are completed.

Reconstruction of acoustic relaxation absorption curve is a powerful approach to ultrasonic gas sensing, but requires known of a series ultrasonic absorption at various frequencies around effective relaxation frequency. Ultrasonic transducer is a most widely deployed sensor for ultrasonic wave propagation measurement and works only at a fixed frequency or specific environment like water, so a large number of ultrasonic transducers operating at various frequencies are required to recover an acoustic absorption curve with a relative large bandwidth, which cannot suit for large-scale practical applications. This paper proposes a wideband ultrasonic sensor using a distributed Bragg reflector (DBR) fiber laser for gas concentration detection through acoustic relaxation absorption curve reconstruction. With a relative wide and flat frequency response, the DBR fiber laser sensor measures and restores a full acoustic relaxation absorption spectrum of CO2 using a decompression gas chamber between 0.1 and 1 atm to accommodate the main molecular relaxation processes, and interrogates with a non-equilibrium Mach-Zehnder (M-Z) interferometer to gain a sound pressure sensitivity of -45.4 dB. The measurement error of the acoustic relaxation absorption spectrum is less than 1.32%.

In this study, divalent Yb2+-doped silica fiber was fabricated using rod-in-tube technology. The fiber core of Yb2+-doped silica glass was prepared by high-temperature melting technology under vacuum conditions. The spectroscopic properties of the Yb2+-doped glass and fiber were studied. The experiments indicate that divalent Yb2+-doped glass has a high quantum efficiency and superbroadband fluorescence in the visible region with an excitation wavelength of 405 nm. In additionally, the results suggest that Yb2+-doped fiber has a potential for application in visible fiber laser and fiber amplification.

Distributed fiber optic strain measurement techniques have become increasingly important in recent years, especially in the field of structural health monitoring of reinforced concrete structures. Numerous publications show the various monitoring possibilities from bridges to special heavy structures. The present study is intended to demonstrate the possibilities, but also the challenges, of distributed fiber optic strain measurement in reinforced concrete structures. For this purpose, concrete beams for 3-point bending tests were equipped with optical fibers on the reinforcement and concrete surface as well as in the concrete matrix in order to record the strains in the compression and tension zone. In parallel, an analytical approach based on the maximum strains in the uncracked and cracked states was performed using the Eurocode~2 interpolation coefficient. In principle, the structural design correlates with the measured values, but the strains are underestimated, especially in the cracked zone. During load increase, structural distortions in the compression zone affected the strain signal, making reliable evaluation in this zone difficult. The information content of distributed fiber optic strain measurement in reinforced concrete structures can offer tremendous opportunities. Future research should consider all aspects of the bond, sensor selection and positioning. In addition, there is a lack of information on the long-term stability of the joint and the fiber coating, as well as the effects of dynamic loading.

We present a novel method for online measurement of multi-point opening distances of midpalatal suture during rapid palatal expansion (RPE) using fiber optic Fabry-Perot (F-P) sensors. The sensor consists of an optical fiber with a cut flat end face and an optical reflector, which are implanted into the palatal base structure of an expander and is capable of measuring the precise distance between two optical reflective surfaces. As a demonstration, a 3D printed skull model containing the maxilla and zygomaticomaxillary complex (ZMC) was produced and a miniscrew-assisted rapid palatal expander (MARPE) with two guide rods was used to generate the midpalatal suture expansion. The reflected spectrums of the sensors were used to dynamically extract cavity length information for full process monitoring of expansion. The dynamic opening of the midpalatal suture during the gradual activation of the expander was measured, and a displacement resolution of 2.5 μm was demonstrated. The angle of expansion was derived and the results suggested that the midpalatal suture was opened with a slightly V type expansion of 0.03 rad at the first loading and subsequently expanded in parallel. This finding might be useful for understanding the mechanical mechanisms that lead to different types of expansion. The use of a fiber-optic sensor for mounting the rapid palatal expander facilitates biomechanical studies and experimental and clinical evaluation of the effects of RPE.

The development of hybrid rockets offers excellent opportunities for the practical education of students at universities due to a high safety and a relatively low complexity of the rocket propulsion system. During the German educational program STERN, students of the Technische Universität Braunschweig obtain the possibility to design and launch a sounding rocket with a hybrid engine. The design of engine HYDRA 4X is presented and results of first engine tests are discussed. Results for measured regression rates are compared to results from literature. Furthermore, the impact of the lightweight casing material CFRP on the hybrid engine mass and flight apogee altitude is examined for rockets with different total impulse classes (10 to 50 kNs). It is shown that the benefit of a lightweight casing material on engine mass decreases with an increasing total impulse. However, a higher gain on apogee altitude, especially for bigger rockets with a comparable high total impulse is shown.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

Surface-enhanced Raman spectroscopy (SERS) can boost the pristine Raman signal by ~ 108 times that could be exploited for producing innovative sensing devices with advanced properties. However, the inherent complexity of SERS systems restricts their further applications in rapid detection, especially in situ detection in narrow aera. Here, we construct an efficient and flexible SERS-based LOP sensor by integrating Ag/Au nanocap arrays obtained by Ag/Au coating polystyrene nanospheres on the optical fiber face. We obtain rich “hotspots” at the nanogaps between neighboring nanocaps and further achieve the excellent SERS performance with the assistance of laser induced thermophoresis on the metal film that can achieve high efficiency aggregation of detected molecules. We achieve a high Raman enhancement with a low detection limitation of 10-7 mol/L for the most efficient samples based on the above sensor. This sensor also exhibits good repeatability and stability under multiple detections, revealing the potential application in situ detection based on the reflexivity of optical fiber.

The opened beams always confused the designers due to the guidelines missing. In this research, six hybrid reinforced beams reinforced with mixed steel and basalt fiber reinforced polymer (BFRP) bars had constant cross-sections of 150mm x 300mm and a clear span of 1800mm. Generally, five beams have symmetrical rectangular openings with dimensions of 150mm x 250mm located at a distance of 250mm (equivalent to the beam effective depth) from the beam support in addition to a solid beam that is served as a control reference. The studied parameters included the effect of using internal reinforcement (steel or BFRP bars) provided along the opening or by incorporating an external BFRP sheet around the opening corners. Also, the conduction of double enhancement with internal steel reinforcement bars further external strengthening BFRP sheet was investigated. The relevant results showed that the opened beam without enhancement lost almost 74.66% of the maximum load compared with the solid beam. Placing internal steel or BFRP bars around the openings increased the maximum load by 62.07% and 59.68%, respectively in comparison to the non-enhanced opened beams. Using an external BFRP sheet to strengthen the opening corners of the beam enhanced the maximum load by 76.39% compared with the non-enhanced opened beam. Therefore, if the beam double enhancement with an external BFRP sheet and internal steel reinforcement around the openings, the maximum load increased by 137.40% compared with the non-enhanced opened beam. Ultimately to further analyze the experimental results and confirm their findings, the study was extended to include the numerical analysis using three dimensional finite element modeling and the results correlated very well with the experimental ones.

Nowadays asymmetric thin film composite (TFC) polymeric hollow fiber (HF) membranes are extensively used in industrial gas/vapor separations, water treatment etc. There are numerous advantages to use hollow fibers such as: low energy requirements, simplicity of operation, and high specificity. In the present article we discuss the progress made during the past decade in the preparation of the HF substrate and preparation/modification of the thin selective layer. Their applications in water treatment, dehydration of alcohols via pervaporation and gas/vapor separation are also demonstrated.

This paper focuses on parametric model order reduction (PMOR) of guided ultrasonic wave propagation and its interaction with damage in a fiber metal laminate (FML). Structural health monitoring in FML seeks to detect, localize and characterize the damage with high accuracy and minimal use of sensors. This can be achieved by the inverse problem analysis approach which employs the signal measurement data recorded by the embedded sensors in the structure. The inverse analysis requires to solve the forward simulation of the underlying system several thousand times. These simulations are often exorbitantly expensive and triggered the need for improving their computational efficiency. A PMOR approach hinged on the proper orthogonal decomposition method is presented in this paper. An adaptive parameter sampling technique is established with the aid of a surrogate model to efficiently update the reduced-order basis in a greedy fashion. A numerical experiment is conducted to illustrate the parametric training of the reduced-order model. The results show that the reduced-order solution based on the PMOR approach is accurately complying with that of the high fidelity solution.

Increasing numbers of researchers are interested in the importance of dietary fiber for the gut microbiota, microbiotal metabolite SCFA, energy metabolism and gut health of the host. However, studies have demonstrated that long-term and longitudinal observation may be needed to evaluate the effect of dietary fiber better, and few such works have been made in chickens. Therefore, we successively fed low-fiber, high--fiber and low-fiber diets to two breeds of chickens during different growth periods (1—8, 9—20 and 21—50 weeks), aiming to longitudinally observe the long-term effect of altered dietary fiber on the gut microbiota, SCFA and development of cecum of chickens with age. The results showed that the composition and function of the gut microbiota, SCFA and the development of the cecum were different during different periods, which was largly affected by dietary fiber. However, the causes of some effects were different during the different periods. For example, compared with that in low-fiber chickens at 8 weeks, dominant fiber-degradation bacteria such as Bacteroidetes, Alloprevotella and SCFA-producing bacteria such as Faecalibacterium increased due to a high-fiber diet at 20 weeks, while due to a high feed intake in 50 weeks. Moreover, the concentration of SCFA in 20 weeks was significantly higher than in 8 weeks and 50 weeks, but the causes of this difference were also distinct. It was proposed that a long-term observation was needed to evaluate the effect of dietary fiber better on chickens. The metabolite pathways of ATP-binding cassette (ABC) transporters encoded by Firmicutes were enriched in 8 weeks, while a two-component system and β–glucosidase encoded by Bacteroidetes were enriched in 20 and 50 weeks. The trend was the same in two breeds of chickens except for Alloprevotella. In addition, the total content of SCFA in the contents of cecum was also affected by the size of the cecum. Surprisingly, the length of the cecum shortened from 20—50 weeks, maybe due to reduced dietary fiber.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

Dietary fibers regulate intestinal barrier function; however, the precise mechanisms remain unclear. This study investigated the effects of psyllium fibers on antimicrobial protein expression, focusing on the type II immunity and tuft cell-group 2 innate lymphoid cell (ILC2) circuit in the small intestine of the mouse. Supplemental psyllium fiber upregulated antimicrobial proteins, such as small proline-rich protein 2A (SPRR2A) and resistin-like beta (RELMβ), in mouse small intestine, evidently affecting cecal microbiota composition. Psyllium fibers also increased the RNA and protein expression of molecules related to ILC2 and tuft cells, such as IL-13, IL-25, DCLK1, Gfi-1b, SH2 domain-containing protein 3C, and Spi-B. In addition, ILC2 inhibitor (disulfiram) and bitter taste receptor blocker administration reduced psyllium-induced SPRR2A and RELMβ expression. Collectively, psyllium supplementation upregulates antimicrobial proteins such as SPRR2A and RELMß via the type II immune response and tuft cell-ILC2 circuit in the mouse small intestine.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

Prestress loss evaluation in prestressed strand is essential for prestressed structures. However, the sensors installed outside the duct can only measure the total prestress loss. The sensors attached on strand inside the duct also have several problems, such as inadequate durability in an aggressive environment, vulnerable damage at tensioning and so on. This paper proposes a new installation method for long-gauge fiber Bragg grating (LFBG) sensor to prevent accidental damage. Then the itemized prestress losses were determined in each stage of the pre-tensioning and post-tensioning according to the LFBG measurements. We verified the applicability of the LFBG sensors for prestress monitoring and the accuracy of the proposed prestress loss calculation method during pre-tensioning and post-tensioning. In the pre-tensioning case, the calculated prestress losses had less deviation from the true losses than those obtained from foil-strain gauges, and the durability of the LFBG sensors was better than foil-strain gauges, whereas in post-tensioning case, the calculated prestress losses were close to those derived from theoretical predictions. Finally, we monitored prestress variation in the strand for 90 days. The itemized prestress losses at each stages of post-tensioning were obtained by the proposed calculation method to show the prospect of the LFBG sensors in practical evaluation.