A new circuit of a low-pass filter (LPF) is considered, which is switched on at the input of analog-to-digital converters to limit the spectrum of input signals. The peculiarity of the proposed low-pass filter is the independent adjustment of the pole frequency, the quality factor of the pole and the transmission coefficient by different resistors. Computer simulation performed in the Micro-Cap environment confirms these properties of the LPF. The basic mathematical expressions are obtained, which make it possible to carry out the parametric synthesis of the LPF circuit. It is shown that the sensitivity of the LPF transmission coefficient to changes in the parameters of the frequency-setting elements of the circuit is close to zero and depends only on the ratio of the resistances of the two resistors in the feedback circuit.

A novel means of applying radiotherapy in cancer treatment is the application of the radiation dose at a very high intensity for a very short time, FLASH radiotherapy (FLASH-RT). This technique involves exposure of tumors to >40 Gy/s, usually for less than one second. Studies conducted in cell and preclinical models suggest that FLASH-RT seems less damaging to normal tissues from adverse effects, relative to the same overall dose of radiation administered in conventional therapy (CONV-RT) which involves administration of lower levels of radiation repeated intermittently over a protracted period. In contrast, the susceptibility of tumor tissues to FLASH-RT is not diminished relative to CONV-RT. Within solid tumors both modes of dispensation of radiation produce an equivalent degree of cell damage. This differential between normal and malignant material has been found in isolated tissues, animal studies, and more recently in clinical trials. However, the classical radiation concept is that high energy linear transfer radiation (LET) is more damaging than the equivalent total dose of low LET. Thus, the susceptibility of cells should be greater to short-term exposure to high LET. This article discusses the potential reasons that may account for this discrepancy. While the relative protection given to untransformed tissues by FLASH-RT relative to tumor tissue is a major step forward in radiation therapy of cancer, the processes that lie behind this phenomenon are incompletely understood and are considered here.

Controlling the collective behavior of micro/nanomotors with ultrasound may enable new functionality in robotic, medicine and other engineering disciplines. Currently, various collective behaviors of nanomotors, such as assembly, reconfiguration and disassembly, have been explored by using acoustic fields with a fixed frequency, while regulating their collective behaviors by varying the ultrasound frequency still remains challenging. In this work, we design an ultrasound manipulation methodology allowing nanomotors to exhibit different collective behaviors by regulating the applied ultrasound frequency. This work has important implications for design of artificial actuated nanomotors and optimize their performances.

Successfully engaging in social communication requires efficient processing of subtle socio-communicative cues. Voices convey a wealth of social information, such as gender, identity and the emotional state of the speaker. We tested whether our brain can systematically and automatically differentiate and track a periodic stream of emotional utterances among a series of neutral vocal utterances. We recorded frequency-tagged EEG responses of 20 neurotypical male adults while presenting streams of neutral utterances at 4 Hz base rate, interleaved with emotional utterances every third stimulus, hence at 1.333 Hz oddball frequency. Four emotions (happy, sad, angry, and fear) were presented as different conditions in different streams. To control the impact of low-level acoustic cues, we maximized variability among the stimuli and included a control condition with scrambled utterances. This scrambling preserves low-level acoustic characteristics but ensures that the emotional character is no longer recognizable. Results revealed significant oddball EEG responses for all conditions, indicating that every emotion category can be discriminated from the neutral stimuli, and every emotional oddball response was significantly higher than the response for the scrambled utterances. These findings demonstrate that emotion discrimination is fast, automatic, and is not merely driven by low-level perceptual features.

A novel kind of power spectrum is constructed, the inter-spike spectrum, which transforms any signal into its spike-frequency domain. This method clearly shows the apparent cycles in the data and overcomes the problems for spike-train-like signals when using the obvious idea of Fourier-transforming it. We invent this instructive approach with the idea of transforming the τ-recurrence rate of a recurrence plot (RP), which often has a spiky appearance. The τ-recurrence rate is the density of recurrence points along diagonals of the RP, which are parallel to the main diagonal with a distance of τ. In this context the inter-spike spectrum can be interpreted as a nonlinear power spectrum of a potentially high dimensional system which constitutes the RP. The proposed measure is robust to noise and is able to detect and analyze bifurcations.

Pneumonic plague outbreaks are relatively infrequent in modern times but in the early part of the 20th century, they were commonplace including several well-documented epidemics responsible for the deaths of thousands. The transmissibility of this disease seems to be discontinuous since in some outbreaks few transmissions occur, while in others, the progression of the epidemic is explosive. Modern epidemiological studies explain that transmissibility within populations is heterogenous with relatively few subjects likely to be responsible for most transmissions and that ‘super spreading events’, particularly at the start of an outbreak, can lead to a rapid expansion of cases. These findings concur with outbreaks observed in real-world situations. It is often reported that pneumonic plague is rare and not easily transmitted but this view could lead to unnecessary complacency since future risks such as the spontaneous incidence of anti-microbial strains, climate change leading to a disruption of natural cycles within plague foci and use of plague as a bioweapon cannot be discounted. Carers and first responders are vulnerable, particularly in poorer countries where access to medicines may be limited, out-breaks occur in inaccessible areas or where there is a lack of surveillance due to a paucity of funds.

An antenna sensor is proposed to execute dual functions of antenna and sensor in the wireless sensor system, in order to reduce data loss and to increase transmission rate by omitting a certain interface. The as-made sensor was test at a center frequency of 46 MHz for measuring human finger postures using principle of dipole antenna. The antenna sensor was attached on a wearable glove. The results showed that the motion sensor can accurately identify finger angles at 0°, 20°, 40°, 60° and 80°.

The signal processing technique is one of the principal tools for diagnosing power quality (PQ) issues in electrical power systems. The Discrete Fourier Transform (DFT) is a frequency analysis technique used to process power system signals and identify PQ problems. However, the DFT algorithm may lead to spectral leakage and picket-fence effect problems for asynchronously sampled signals that contain harmonic, inter-harmonic, and flicker components. To resolve this shortcoming, a hybrid method for frequency estimation based on a second-level DFT approach and a frequency-domain interpolation algorithm to obtain the accurate fundamental frequency of a power system is proposed in this paper. This method uses a second-level DFT to compute the cosine and sine parts for the fundamental frequency components of the acquired signals. Then, a frequency-domain interpolation approach is adopted to determine the amplitude ratio for the cosine and sine parts of the system's fundamental frequency. To demonstrate the performance of the proposed frequency estimation method, the observation window used by this paper to evaluate different estimation algorithms is 200 ms. According to the IEC standards, a 200 ms acquisition window is recommended for power system quality assessment. A set of mixed signals with harmonic, inter-harmonic, and flicker components with the fundamental frequency deviation is used. The evaluation results demonstrate the superiority of the new method over other approaches for assessing asynchronously sampled signals contaminated with noise, harmonic, inter-harmonic, and flicker components.

This study aimed to investigate the relationship between sleep duration, dementia severity, age, and ANS regulation. This cross-sectional pilot study included 27 older patients with probable Alzheimer’s disease, hospitalized at a psychiatric center. We measured heart rate variability to assess ANS regulation at night, evaluated dementia severity using the Clinical Dementia Rating scale, and obtained sleep duration data from sleep diaries maintained by psychiatric nurses. The data were analyzed using repeated-measures generalized linear models with age, sex, dementia severity, and medication (antipsychotics) as covariates. A sleep duration of 7–8 h per night was associated with better ANS regulation than other sleep durations, as indicated by sympathovagal balance (p = 0.005). ANS dysregulation was characterized by a 20.7% increase in sympathetic nervous system activity and a 14.8% decrease in parasympathetic nervous system (PSNS) activity. We found a significant correlation between dementia severity and PSNS activity (p = 0.04) and observed an inverted U-shaped association between sleep duration and ANS regulation. This pilot study demonstrated that a sleep duration of 7–8 h per night may be critical in maintaining optimal ANS regulation. Bidirectional associations between sleep duration, inadequate sleep duration, aging, and ANS regulation warrant further investigation.

The South African Weather Service (SAWS) manages an in-situ solar irradiance radiometric network of 13 stations and a very dense sunshine recording network; located in all six macro-climate zones of South Africa. A sparsely distributed radiometric network and over a landscape with dynamic climate and weather shifts is inadequate for solar energy studies and applications. Therefore, there is a need to develop mathematical models to estimate solar irradiation for a multitude of diverse climates. In this study, the annual regression coefficients, a and b, of the Ångström-Prescott (AP) model that can be used to estimate global horizontal irradiance from observed sunshine hours were calibrated and validated with observed station data. The AP regression coefficients were calibrated and validated for each of the six macro-climate zones of South Africa using the observation data that spans 2013 to 2019. The predictive effectiveness of the calibrated AP model coefficients was evaluated by comparing estimated and observed daily global horizontal irradiance. The maximum annual relative Mean Bias Error (rMBE) was 0.371 %, relative Mean Absolute Error (rMAE) was 0.745 %, relative Root Mean Square Error (rRMSE) was 0.910 % and the worst-case correlation coefficient (R2) was 0.910. The statistical validation metrics results show that there is a strong correlation and linear relation between observed and estimated solar radiation values. The AP model coefficients calculated in this study can be used with quantitative confidence in estimating daily GHI data at locations in South Africa where the daily observation sunshine duration data is available.

High-intensity interval training (HIIT) is widely used in team sports, particularly in soccer. This study aimed to investigate the effects of a short-term, progressive- load HIIT program on the performance of under-15 soccer players. The sample consisted of 30 adolescent soccer players, aged 14, who were randomly divided into two groups: the control group (CG, n=15) and the intervention group (EX, n=15), which performed additional HIIT sessions. The duration of the training program was six weeks, with progressive overload applied every two weeks. Performance indicators, including speed over 10 and 30 meters, change of direction (COD) to the right and left (505 right and left), maximal oxygen uptake (30-15IFT), and repeated sprint ability (RSA) (RSAtotal, RSAmean, RSAdecrement), were measured before and after the training program. Significant improvement were observed in the intervention group in COD (505 right and left), 30-15IFT, and RSAtotal and RSAmean (p=0.027, p=0.005, p=0, p=0.015, p=0.031, p=0.028, respectively). The findings of the present study suggest that a short-term, progressively overloaded HIIT program can enhance direction change ability, aerobic capacity, and repeated sprint performance.

The paper considers two models of queuing with a varying structure based on the introduction of additional transient intensities into known models or their combinations, which create stationary distributions convenient for calculation. In the first model, it is a probabilistic mixture of known stationary distributions with given weights. In the second model, this uniform distribution is repeatedly used in physical statistics. Both models are based on the selection of states, between which additional transient intensities are introduced. The algorithms used in the paper for introducing new transient intensities are closely related to the concept of flow in a deterministic transport network. The introduced controls are selected so that the marginal distribution of the combined system is a mixture of the marginal distributions of the combined systems with different weights determined by the introduced transient intensities. As a result, the process of functioning of the combined system is obtained by switching processes corresponding to different combined systems at certain points in time.

The risk factors and positive factors of teleworking have been widely analyzed. Emotional exhaustion has been one of the most studied among them. However, the impact of ethical leadership in virtual environments has remained completely unnoticed. There is no clear answer to whether the ethical leader is a factor that buffers or accelerates stress-related processes in teleworking. Furthermore, the role of perceived work autonomy as a theoretical mechanism that protects against specific adverse psychological outcomes requires more scientific evidence because the results obtained so far are confusing and contradictory. Therefore, this study explores how and when ethical leadership influences emotional exhaustion through work autonomy and teleworking intensity (TI). The sample consisted of 448 professionals from six organizations in the Colombian electricity sector. The mediation effect was evaluated through a four-step procedure, and the moderated mediation model was analyzed using statistical tools such as PROCESS and AMOS macros for SPSS. Surprisingly, our results revealed a positive relationship between ethical leadership and emotional exhaustion, with work autonomy potentially mediating this relationship. However, teleworking intensity (TI) was found to moderate this mediation process. Specifically, the negative impact of ethical leadership on emotional exhaustion was nullified when TI was high. Moreover, a high level of TI strengthened the relationship between ethical leadership and work autonomy, while weakening the positive relationship between work autonomy and emotional exhaustion. In conclusion, our study suggests a potential positive relationship between ethical leadership and emotional exhaustion from the follower's perspective. However, the number of teleworking days can influence this trend, potentially even reversing it. In other words, teleworking intensity (TI) is a resource as its intensity increases, and it can alter the direction of work autonomy and reconfigure the relationship between ethical leadership and emotional exhaustion. This study, to the best of our knowledge, is the first to analyze these variables, significantly contributing to our understanding of the attributes of ethical leadership and its impact on employee well-being.

The dominant part of energy performance of a building consists of consumption of heating and lighting. Both heating and lighting systems of buildings work at their designed efficiency for most of the buildings’ lifetimes. Interference with existing systems is costly considering replacements and construction adjustments. Therefore, considerable effort must be put into the design of these systems during the building design phase. The article is focused on luminaire layout design strategy, which affects the number of luminaires in a building and therefore their power consumption and the sustainability of the building. A genetic algorithm with radiosity implemented has been used to find suitable placements of luminaires of a single type in a model room to decrease the number of luminaires as much as possible. Three outcomes of optimal luminaire layout design are presented in this paper, including design strategy conclusions. Results of calculation outcomes are verified by software DIALux, that is commonly used for designing lighting systems.

Microalgae are photosynthetic microorganism able to receive light from sunlight and external light sources for their growth. Despite the simplicity of cultivation and their widespread presence, the growth of microalgae is affected by several factors, light intensity being a crucial one as it is linked to external environmental conditions. On the other hand, microalgae cultivation in wastewater with high nitrogen content has become a promising alternative as a low cost nutrients substrate method. However, effluents may contain many compounds, making therefore difficult the assessment of light intensity on cells growth profile and especially on nutrients assimilation rate. The aim of this study was the examination of the effect of intensity of light source on the growth and nutrient uptake rates by a freshwater microalgae, Chlorella sorokiniana in the effluent from an anaerobic digestion plant, with nitrogen content reaching up to 5 g/L. Microalgae were cultivated using three light intensities (1,500, 5,000 and 12,000 lx) in 10% digestate mixtures in water. Samples were collected and analyzed for the presence of microalgae cells, while aqueous phase samples were subjected to the analysis of nitrogen and phosphorous content. Biomass productivity followed the light intensity pattern: the highest the light the highest the cells growth. A similar pattern was observed in the reduction rate of nitrogen and phosphorous concentrations; however, nutrients reduction rate per gram of microalgae were mainly associated to biomass growth rate, indicating that the effect of light intensity was significant for biomass growth, without however changing the main nutrients assimilation pathway. In addition, results indicated that under high light intensity, microalgae might change their metabolism towards formation of lipids against nitrogenous compounds.

In this study, Fluent software 2020R2 is used to simulate vertical axis turbine in two dimensions, aiming to analyze the influence of turbulence intensity on wake characteristics. The detailed flow field data are obtained by simulating the operation of turbine under different turbulence intensities. On this basis, the influence factor of turbulence intensity are creatively introduced into the wake mathematical formula of vertical axis turbine established by Lam, and some parameter calculations of the formula are supplemented and perfected. The results show that the theoretical model can well reflect the influence of turbulence intensity on the wake distribution of vertical axis turbines. The formula can provide a theoretical basis for the design and optimization of vertical axis turbines and the array arrangement, and can be used to predict the wake characteristics under different turbulence intensity operating conditions.

The EU has planned the phase-out of new vehicles based on internal combustion engines in favour of high efficiency electric cars by 2035 (Fit for 55 package). However, many doubts remain about the effectiveness of this choice for each Country of the Union in terms of CO2 emissions reduction, as each State is characterized by a different carbon intensity related to the production of electricity needed to manufacture and recharge vehicles. This study seeks to explore the Italian case. To this aim, carbon intensities related to the electricity production were calculated considering both the Italian electricity mix production at 2021 and those at 2035, envisaged considering two scenarios based on different introductions of renewable sources (RES). Afterwards, the values obtained were adopted for determining the CO2 emissions related to the whole production process of battery systems in Italy (emissions from mining and refining, scrap materials and final assembly included) by comparing some of the most up-to-date Life-Cycle Assessment (LCA) analysis related to the manufacturing cycle of the batteries. Finally, the results were adopted to calculate the starting carbon debit for A, B, C and M car segments for Mild Hybrid, Full Hybrid and Full Electric powertrains. At the same time, statistical road fuel/electricity consumption data were collected and overall CO2 emissions were calculated for the same vehicles for a defined mileage, so to determine break-even points with respect to the cumulative (i.e., from battery and road) carbon emissions. The results showed that advantages related to electric vehicles are significant only if a low carbon intensity related to electricity production is reached by means of a very high introduction of RES, thus keeping the door open for innovative powertrain technologies (plug-in), if fed with low carbon fuels.

A number of accidents at sea are primarily caused by low visibility due to sea fog therefore, it is important to estimate sea fog intensity and visibility in real-time in the ocean environment. However, the existing estimation systems have significant costs so that it is not viable to install them at various locations, such as small vessels, minor ports, and a number of buoys. Therefore, this paper proposes an algorithm called RDCP (Reduced Dark Channel Prior) which provides the estimation at a low complexity and a low cost. For the estimation, the RDCP algorithm firstly acquires dark channels from an ocean image, then applies an optimized threshold value to the dark channels, and crops out the sky region in the ocean image. For the estimation performance evaluation, 320 raw images captured from cameras at four different ports in South Korea are used rather than artificially composed images. Considering facilities in oceans which are usually operated in the power limited environment, the processing time performance of PDCP are also examined. The experiments demonstrate that the RDCP algorithm provides reliable estimation performance in real-time.

The amount of heat transfer in gas turbine blades depends on cooling techniques and various flow phenomena. The effect of eddies, passing shock waves and free flow turbulence has been noticed by many researchers since the beginning. The focus of the upcoming work is on the numerical investigation of the effects of turbulence intensity and Reynolds number on the amount of heat transfer from the blade surface with internal cooling. The SST model has been used to solve this problem, which has been compared with the experimental work to ensure the correctness of the numerical simulation. In this regard, by changing the free flow turbulence intensity with values of 1, 5, 7, and 10% and at three Reynolds numbers of 150,000, 350,000, and 750,000, the changes in heat transfer coefficients have been investigated. The results show that with the increase of the turbulence intensity at different Reynolds numbers, due to the positive effect of the flow turbulence on the suppression of separation and promotion of the boundary layer transition, the blade surface heat transferincreases and this increase is more evident at higher Reynolds numbers.

The purpose of this study was to quantify characteristics of bimanual movement intensity during 30-hour Hand Arm Bimanual Intensive Therapy (HABIT) and bimanual performance (activities and participation) in real-world using accelerometers in children with unilateral cerebral palsy (UCP). Twenty-five children with UCP participated in a 30-hour HABIT program. Data was collected from bilateral wrist-worn accelerometers during 30-hours HABIT to quantify the movement intensity, and three days pre- and post-HABIT to assess real-world performance gains. Movement intensity and performance gains were measured using six standard accelerometer-derived variables. Bimanual capacity (body function and activities) was assessed using standardized hand function tests. We found that accelerometer variables increased significantly during HABIT, indicating increased bimanual symmetry and intensity. Post-HABIT, children demonstrated significant improvements in all accelerometer metrics, reflecting real-world performance gains. Children also achieved significant and clinically relevant changes in the hand capacity following HABIT. Therefore, our findings suggest that accelerometers can objectively quantify bimanual movement intensity during HABIT. Moreover, HABIT enhances hand function as well as activities and participation in real-world situation in children with UCP.

Dolomite is a common type of natural soluble rock. The strength of rock decreases under the action of corrosion, which has a significant impact on the self-stability and long-term safety of the tunnel surrounding the rock. To reveal the microscopic structure evolution and strength-damage law of carbonate rock caused by corrosion, chemical corrosion, rock uniaxial compression, and electron microscope scanning tests are conducted at different pH values on the dolomite of the Doushantuo Formation. The rock dissolution at different pH values exhibits four typical stages: the initial dissolution stage, secondary dissolution acceleration stage, stable dissolution rate stage, and dissolution attenuation stage. During the dissolution process, the initial dissolution rate is 25.91 times that of the stable stage, and the maximum strength attenuation is 76.2% after 21 days of dissolution. For macroscopic failure, the rock is developed from 1 to 2 external fractures to multiple internal and external fractures and penetrated, and the specimen transforms from brittle to flexible. For microstructure, the sample exhibits corrosion characteristics along the joint surface, intensified corrosion at the edge, etc. The porosity increase rate is 0.6%/d; however, the length–width ratio of the pores is maintained at 1.7–1.85, indicating that the development rate of pores in different directions is similar. The results of this study have enriched the study of the dolomite dissolution mechanism and have important reference value for the stability evaluation of tunnel surrounding rock in karst environments.

The study describes the acute and delayed time course of recovery following the CrossFit® Benchmark Workout Karen. Eight trained men (28.4±6.4 years; 1RM back squat 139.1±26.0 kg) undertook the Karen protocol. The protocol consists of 150 Wall Balls, aiming to hit a target 3 meters high. Countermovement jump height (CMJ), creatine kinase (CK), and perceived recovery status scale (PRS) (general, lower and upper limbs) were assessed pre, post-0h, 24h, 48h and 72h after the session. The CK concentration 24h after was higher than pre-exercise (338.4 U/L vs. 143.3 U/L; effect size: 0.74; p≤0.05). At 48h and 72h following exercise, CK concentration had returned to baseline levels. The PRS general and of the lower limbs were lower in the 24-hours post-exercise compared to pre-exercise (PRS general: 4.7 ±1.5 and 7.9 ±1.7 mmol/L; and PRS of the lower limbs: 4.0 ±2.5 and 7.9 ±0.8, respectively). The PRS general, lower, and upper limbs were reduced at 48-post exercise compared to 72-hours post-exercise scores. Our findings provide insights into the fatigue profile and recovery in acute CrossFit® and can be useful to coaches effectively design the daily session.

Diverse factors may have an impact in Carbon dioxide (CO₂) emissions; thus, three main contributors, energy consumption, exergy indicator and gross domestic product (GDP) are examined in this work. This study explores the relationship between economic growth and energy consumption by means of the hypothesis postulated for the Environmental Kuznets Curve (EKC). Panel data for 10 countries, from 1971 to 2014 have been studied. Despite all this wide gamma of research, the role of an exergy variable has not been tested to find the EKC; then exergy analysis is proposed. Exergy analyses were developed to propose an exergetic indicator as a control variable and a comparative empirical study is developed to study a multivariable framework with the aim to detect correlations between them. High correlation between CO₂, GDP, energy consumption, energy intensity and trade openness are observed, conversely not statistically significant values for trade openness and energy intensity. The results do not support the EKC hypothesis, however exergy intensity opens the door for future research once it proves to be a useful control variable. Exergy provides opportunities to analyze and implement energy and environmental policies in these countries, with the possibility to link exergy efficiencies and the use of renewables.

Background: Depression presents with altered energy regulation and neural plasticity. Previous electroencephalography (EEG) studies showed that practice increases power in beta range (13-30 Hz) in healthy subjects but not in those with impaired plasticity. Here, we ascertain whether depression presents with alterations of spectral activity and connectivity before and after practice. Methods: We used publicly available resting state EEG (64 electrodes) of 122 subjects. Based on Beck Depression Inventory (BDI) score, they were assigned to either high BDI (hBDI, BDI>13, N=46) or control (CTL, BDI<7, N=75) group. We analyzed spectral activity, theta-beta and theta-gamma phase-amplitude coupling (PAC) of EEG recorded before and after a learning task. Results: At baseline, compared to CTL, hBDI group exhibited greater beta power over fronto-parietal regions and gamma over right parieto-occipital area. After practice, increases in all frequency ranges were observed only in CTL. Theta-beta and theta-gamma PAC were greater in hBDI before the task but not after the task. Conclusions: The lack of substantial post-task growth of beta power in depressed subjects likely represents power saturation due to greater baseline values. We speculate that inhibitory/excitatory imbalance, altered plasticity mechanisms, and energy dysregulation present in depression may contribute to this phenomenon.

We report the results of an analysis of the functional capabilities of the KTP crystal and its isomorphs for nonlinear-optical frequency conversion of all types of interaction in the transparency range of the crystal. The possibility of implementing angle-, wavelength- (frequency-) and temperature-noncritical phase matching is shown.

The superharmonic imaging of tissue has the potential for high spatial and contrast resolutions, compared to the fundamental and second harmonic imaging. For this technique, the spectral bandwidth of an ultrasound transducer is divided for transmission of ultrasound and reception of its superharmonics (i.e., higher than the second harmonic). Due to the spectral division for the transmission and reception, transmitted ultrasound energy is not sufficient to induce superharmonics in media without using contrast agents, and it is difficult that a transducer has a -6-dB fractional bandwidth of higher than 100%. For the superharmonic imaging of tissue, thus, multi-frequency array transducers are the best choice if available; transmit and receive elements are separate and have different center frequencies. However, the construction of a multi-frequency transducer for intravascular ultrasound (IVUS) imaging is particularly demanding because of its small size of less than 1 mm. Here, we report a recently developed dual-element focused IVUS transducer for the third harmonic imaging of tissue, which consists of a 35-MHz element for ultrasound transmission and a 105-MHz element for third harmonic reception. For high quality third harmonic imaging, both elements were fabricated to have the same focus at 2.5 mm. The results of tissue mimicking phantom tests demonstrated that the third harmonic images produced by the developed transducer had higher spatial resolution and deeper imaging depth than the fundamental images.

This paper considers the problem of predicting earthquakes. It uses a small amount of information to create a descriptive key that can be used as a footprint to describe an event. A frequency grid clusters events that occurred at the same time and then the algorithm averages the history of these events over preceding days, in particular the gaps when the events did not occur. The gaps are measured for the clustered events only and can be used to create a description that is quite unique. Results suggest that seismic events can in fact be traced using this key and subsequently recognised again, if the same conditions reoccur. They also suggest that force direction may be more important than magnitude, for this type of earthquake. Greek and USA datasets have been looked at and the prediction accuracy can be 70% or better. The author therefore suggests that this is an interesting method that deserves attention.

Research into improving the functionality and capacities of wearable technology has surged as a result of its fast progress. The functioning of wearable technology is largely dependent on antenna design, which provides wireless connectivity and communication. This study of the literature searches many online sources for pertinent research on the various antenna designs for wearable technology. The findings verified that the materials vary based on the design being employed. An analysis was conducted on the gain, frequency, materials, and sizes. The review excels at synthesizing research and literature despite its restricted resources.

AbstraIncorporating knowledge of indigenous forage legumes or associated nutritional attributes in cultivated pastures has the potential to improve grazing conditions, rangeland conditions, and cattle productivity. Climate change and other site-specific factors such as land sizes and other grazing management practices play a significant role in food security, job creation, and environmental health. Several research results have reported that the utilization of forage legumes in most farming systems has proved to increase herbage yield and soil fertility. The major aim of this review is to elucidate the potential benefits of intercropping indigenous forage legumes such as cowpea (Vigna unguiculacta L.Walp) and Dolichols (Lablab purpureaus) intercropped with Chloris gayana, this is to assesses the principal advantages, productivity, and overall performance of forage legumes grown in conjunction with grasses. Moreover, this review seeks to provide insights into the optimal management practices for intercropping forage legumes with grasses. The promising feature of intercropping South African pastoral systems must target the ability of forage legumes in terms of performance and utilization of agro-symbiotic relationships of N2 fixation symbiotic relationship in pastures. Moreover, this review aims also to address this knowledge gap by assessing the effects of defoliation frequency on the biomass production of selected forage legumes when intercropped with Chloris gayana in different growing seasons. By examining how varying defoliation frequencies influence biomass production, this review aimed to provide practical recommendations for optimizing forage management practices and promoting sustainable forage production systems. Through this investigation, we can gain insights into the complex dynamics between the defoliation frequency, intercropping systems, and biomass production.

The earthquake alert of the early warning systems is based on the delay that the S waves have in reference to the P waves and on the interpretation of the P waves’ specific parameters. One of the most used parameters for estimating the moment magnitude of an earthquake is the characteristic period measured in the first 3 seconds of the appearance of the P wave. The typical method determines the characteristic period in the time domain, based on the velocity wave and the displacement wave. In the present work, we present a method for estimating the frequency of the characteristic period. This method includes zero padding of the P wave sequence, conversion of the extended sequence from the time domain to the frequency domain, the identification of local frequency maxima and the calculation of the weighted average of the frequency based on the identified maxima. Tests conducted on synthetic signals, as well as standard deviation evaluation tests for simultaneous recordings on several stations, reveal better performance to the usual method.

This study explores the relationship between mental and physical therapeutic through three dimensions: man-environment relationships; a sense of place and symbolic landscapes. The study used a combination of qualitative and quantitative research methods. Local residents living in the coastal area of Xinglin Bay are the research objects. Quantitative data analysis revealed that the frequency of residents' visits was an important variable affecting their physical and treatment perceptions. In addition, the significance is higher for females than for males. The text analysis shows that the environment, especially the ecological restoration of water quality and migratory birds, is of great significance to the identity of local residents. Daily activities contribute to a sense of place and are what make the coast a place of therapeutic landscape function.

Modifiable THz spectral shapes are important tools that facilitate the comprehensive study of phonon dynamics in condensed matter systems. The generation of narrow bandwidth THz spectra with tunable center frequency which are suitable THz forms needed to achieve such objectives are currently less studied from the table top laser-induced plasma emitters’ perspective. This experimental research is aimed at developing a robust two-color laser induced plasma set-up comprising of a temporal pulse stretcher and an Optical Parametric Amplifier that generates chirped and wavelength tunable pulses respectively. By focusing and independently controlling the ω and 2ω arms of the chirped pulses resulting after the interaction with a β-BBO crystal, I aim to generate narrow bandwidth THz signal (from plasma) scalable at MV/cm intensity and tunable in a wide THz spectral range, in addition to varying the frequency ratio mix.

The vast rise in the number of Internet-connected devices necessitates a more accessible spectrum. As a result, Cognitive Radio was already proposed as a solution to the problem of restricted spectrum resources by utilizing available spectrum which is assigned to primary users. This method allows the secondary user to utilize the spectrum whenever the primary user is not using it, and it does so without intruding with the primary user. Whenever the secondary user detects the spectrum, it faced some issues, such as complexity in sensing leading to a lack of noise value, and the primary user is hidden to all secondary users. In order to tackle these challenges, an adaptive threshold matched filter detector and a cooperative matched filter detector are utilized in this paper to detect the spectrum. The probability of detection (Pd), probability of miss detection (Pm), and probability of false alarm (Pf) are the metrics used to assess sensing accuracy. To simulate suggested detectors, the MATLAB R2020a software was utilized. In comparison to earlier studies, the simulation conclusions reveal that the detection process starts with lower SNR values.

A The present investigation was undertaken in foothill regions of Uttarakhand from July-2016 up to December-2018. A total of thirty four different sites ranging from the roadside areas, grasslands to forests were studied and Mushroom fruiting bodies were collected. A total of One Hundred sixty six fruiting counts were obtained and 68 mushroom genera belonging to 15 orders and 43 families were identified. During collection visits mushroom were apparent from organic debris of diversified habitats ranging from humid soil; grassland; leaf litter; living tree trunk; dead wood log of forest zone. Maximum fruiting bodies (75%) were obtained between July to September and minimum i.e. 6% between November – February. Among the collected mushroom Stereum rugosum, Crepidotus variabilis, Laccaria laccata, Schizophyllum commune, Ganoderma applantum, Cantharellus cibarius were more prevalent. Out of all collected mushroom sample the frequency of Mushroom belonging to order Agaricales was 45.18% followed by Polyporales i.e., 27.7%. The collected mushroom were cultured on PDA medium and their mycelial forms were preserved for further studies.

There is an increasing need for quantitative rockfall hazard and risk assessment that requires a precise definition of the terms and concepts used for this particular type of landslide. This paper suggests to use terms that appear to be the more logic and explicit as possible, and describes methods to derive some of the main hazard and risk descriptors. The terms and concepts presented concern the rockfall process (failure, propagation, fragmentation, modelling) and the hazard and risk descriptors, distinguishing the cases of localized hazards and diffused hazards. For a localized hazard, the failure probability of the considered rock compartment in a given period of time has to be assessed and the probability for a given element at risk to be impacted with a given energy must be derived combining the failure probability, the propagation probability and the exposure of the element. For a diffuse hazard that is characterized by a failure frequency, the number of rockfalls reaching the element at risk per unit of time and with a given energy (reach frequency) can be derived. However, when the element at risk is not replaced or repaired, the probability that it is impacted by at least one rockfall must be considered.

Qualitative and quantitative values estimation is a crucial aspect of social data science and plays a vital role in social and psychological research. Numerous methods of personal values measurement such as Schwartz Value Survey (SVS) and its re-modified versions have been proposed and invented, but many are challenged with one or more limitations. In this article, an alternative approach in a new paradigm of values measurement called Kabiru’s Value Survey (KVS) was proposed to measure the relative degree of importance or significance attached to particular value-actions of an individual(s) in a given population over a period. The methodological innovations in KVS unlike other existing methods of human value measurement include the use of habitually reported practices associated with a particular value-action in place of judging the series of Schwartz hypothetical statements, the use of multiple dependent variables rather than a single coded hypothetical statement. In terms of data analysis, a new approach of multivariate compression is introduced which merges the chain of multiple dependent variables into one coded scale. Psychometric result interpretation is also another innovative aspect of KVS methodology. Finally, the proposed methodology however solved some of the criticized limitations of the other methods of human value measurement.

We report an all-optical radio-frequency (RF) spectrum analyzer with a bandwidth greater than 5 terahertz (THz), based on a 50-cm long spiral waveguide in a CMOS-compatible high-index doped silica platform. By carefully mapping out the dispersion profile of the waveguides for different thicknesses, we identify the optimal design to achieve near zero dispersion in the C-band. To demonstrate the capability of the RF spectrum analyzer, we measure the optical output of a femtosecond fiber laser with an ultrafast optical RF spectrum in the terahertz regime.

This paper studied the solar PV frequency control in the U.S. Eastern Interconnection (EI) and Texas Interconnection (ERCOT) systems. The studied frequency control approaches include droop frequency control, inertia control, and droop-inertia-combined frequency control. The control effects of different frequency controls of PV in the EI and ERCOT are studied using actual high PV penetration interconnection grid models to provide suggestions to the future revision of future PV frequency control standards.

Approximately 300 different types of blood groups are identified so far, the ABO and Rh antigens are still the clinically most significant and genetically most polymorphic of all human blood group systems to date. A total of 200 unrelated individuals from Uttar Pradesh were studied for the phenotype and allele frequency distribution of ABO and Rh (D) blood groups. In total 200 samples analyzed, phenotype B blood type has the highest frequency 36.5% (n=73), followed by O (34.5%; n=69), A (20.5%; n=41) and AB (8.5%; n=17). The O, A and B frequencies were 0.5849, 0.1571 and 0.2580 respectively. The overall phenotypic frequencies of ABO blood groups were B>O>A>AB. The variation in phenotypic frequencies between male and female might be due to small sample size of male sample. The allelic frequency of Rh-negative was 0.2.

Methods of path integrals are used to develop multi-factor probabilities of bid-ask variables for use in high-frequency trading (HFT). Adaptive Simulated Annealing (ASA) is used to fit the nonlinear forms so developed to a day of BitMEX tick data. Maxima algebraic code is used to develop the path integral codes into C codes, and sampling code is used for the fitting process. After these fits, the resultant C code is very fast and useful for forecasting upcoming ask, bid, midprice, etc., when narrow and wide windows of incoming data are used. A bonus is the availability of canonical momenta indicators (CMI) useful to forecast direction and strengths of these variables.

We propose a probabilistic graphical model for discriminative substrate characterization, to support geological and biological habitat mapping in aquatic environments. The model, called a fully connected conditional random field (CRF), is demonstrated using multispectral and monospectral acoustic backscatter from heterogeneous seafloors in Patricia Bay, British Columbia, and Bedford Basin, Nova Scotia. Unlike previously proposed discriminative machine learning algorithms, the CRF model considers both the relative backscatter magnitudes of different substrates and their relative proximities. The model therefore combines the statistical flexibility of a machine learning algorithm with an inherently spatial treatment of the substrate. The CRF model predicts substrates such that nearby locations with similar backscattering characteristics are likely to be in the same substrate class. The degree of proximity and allowable backscatter similarity are controlled by parameters that are learned from the data. CRF model results were evaluated against a popular generative model known as a Gaussian Mixture model that doesn't include spatial dependencies, only covariance between substrate backscattering response over different frequencies. Both models are used in conjunction with sparse bed observations/samples in a supervised classification. A detailed accuracy assessment, including a leave-one-out cross-validation analysis, was performed using both models. Using multispectral backscatter, the GMM model trained on 50% of the bed observations resulted in a 75% and 89% average accuracies in Patricia Bay and Bedford Basin, respectively. The same metrics for the CRF model were 78% and 95%. Further, the CRF model resulted in a 91% mean cross-validation accuracy across four substrate classes at Patricia Bay, and a 99.5% mean accuracy across three substrate classes at Bedford Basin, which suggest that the CRF model generalizes extremely well to new data. This analysis also showed that the CRF model was much less sensitive to the specific number and locations of bed observations than the generative model, owing to its ability to incorporate spatial autocorrelation in substrates. The CRF approach therefore may prove to be a powerful `spatially aware' alternative to other discriminative classifiers.

Background: Variations in several clopidogrel-pharmacogenes have been linked to clopidogrel response variability and clinical outcomes. We aimed to determine the frequency distribution of major polymorphisms on CYP2C19, PON1, ABCB1 and P2RY12 pharmacogenes in Puerto Ricans. Methods: This was a cross-sectional, population-based study of 200 unrelated “Guthrie” cards specimens from newborns registered in the Puerto Rican Newborn Screening program (PRNSP) between 2004 and 2014. Taqman® SNP assay techniques were used for genotyping. Results: Minor Allele Frequencies (MAF) were 46% for PON1 (rs662), 41% for ABCB1 (rs1045642), 14% for CYP2C19*17, 13% for CYP2C19*2, 12% for P2RY12-H2 and 0.3% for CYP2C19*4. No carriers of the CYP2C19*3 variants were detected. All alleles and genotype proportions were found to be in Hardy-Weinberg equilibrium (HWE). Overall, there were no significant differences between MAFs of these variants in Puerto Ricans and the general population (n=453) of the 1,000 Genome project, except for the Yoruba in Ibadan from Nigeria (YRI, West-African ancestry; p<0.05). As expected, the prevalence of these markers in Puerto Ricans most resembled those in the 181 subjects from reference populations of the Americas. Conclusions: These prevalence data provide a necessary groundwork for future clinical studies of clopidogrel pharmacogenetics in Caribbean Hispanics.

Evaluation of the effect of a high frequency acceleration device on clear aligner exchange intervals and treatment time required to achieve prescribed tooth movements. Sixteen subjects with similar Class I malocclusions, 5mm or less crowding, and treated with Invisalign were divided into two groups. Group 1 (experimental; N=8) underwent aligner treatment in conjunction with daily use of the high frequency acceleration device and exchanged aligners every 5 days. Group 2 (controls; N=8) underwent aligner treatment without use of the device and exchanged aligners every 14 days according to the manufacturer's recommended interval. All subjects were treated by one investigator, and results were evaluated by both; total number of aligners used, and number of refinements required, prior to final Vivera retention scan. A significant decrease in both treatment time, and number of aligners required to complete treatment was observed by experimental subjects as compared to controls. In addition, no refinements were required by experimental subjects, whereas 6 of 8 of the control subjects required 1 or more refinements. Use of the high frequency acceleration device in conjunction with Invisalign treatment resulted in more predictable tooth movement and a significant decrease in the length of treatment.

The aim of this paper is to apply all the existing pyranometric method, to estimate the sunshine duration from the global solar irradiation, in order to find in their original form the most suitable method for a tropical site. Then, in a second step, one of these methods will be optimized to well fit tropical sites. Five methods in the literature (Step Algorithm, Carpentras Algorithm, Slob &amp; Monna Algorithm, Slob &amp; Monna 2 Algorithm, and Linear Algorithm) were applied with eleven years of global and diffuse solar radiation data. As a result, in their original form, the Step Algorithm is on the first rank. But in the second step, after improving its main coefficients, the Carpentras Algorithm was found to be the best algorithm for tropical site in the southern hemisphere.

Radiative budget is one of the key factors influencing climate change. The aim of this study is to analyze radiative regime in Moscow using the MSU-RAD(BSRN) instrumentation complex and to estimate radiative effects of the main atmospheric factors during the 2021-2023 period. Due to variations in aerosol content, the loss of global shortwave irradiance (Q) varies from 37 to 186 W/m2 (or about 18-22%) at different solar elevations with a significant decrease in direct irradiance and increase in diffuse irradiance due to multiple scattering. In winter, we observed the increase in Q of about 45 W/m2 (or 9%) at h=30° due to high surface albedo, smaller aerosol and water vapor content. At the same time, net shortwave irradiance (Bsh) demonstrates a significant decrease due to prevailing effects of snow albedo. A nonlinear dependence of Q and Bsh cloud transmittance on relative sunshine duration (Sd) is observed. Mean changes in Q against the 1955-2020 period are characterized by negative anomalies (-22%) in winter and positive anomalies in summer (+3%) due to the changes in cloudiness, reflected in Sd variations. This is in line with global tendencies in long-term changes of shortwave irradiance in moderate climate in Europe during the last years.

Ambient vibration energy is widely being harnessed as a source of electrical energy to drive low-power devices. The vibration energy harvester (VEH) of interest employs an electromagnetic transduction mechanism, whereby ambient mechanical vibration is converted to electrical energy. The limitations affecting the performance of VEHs, with an electromagnetic transduction structure, include its operational bandwidth as well as the enclosure-size constraint. In this study, an analysis and design of a nonlinear VEH system is conducted, using the Output Frequency Response Function (OFRF) representations of the actual system model. However, the OFRF representations are determined from the Generalised Associated Linear Equation (GALE) decompositions of the system of interest. The effect of both nonlinear damping and stiffness characteristics, to respectively extend the average power and operational bandwidth of the VEH device, is demonstrated.

Considering the widespread issue of distracted eating, our study explores how cognitive dis-traction influences the sensory perception of food-related odors among individuals with varying weight statuses. We used the Tetris game to mimic the dynamic nature of real-life cognitive dis-traction. Participants, categorized into a lean and an overweight/obese group based on their body mass index (BMI), rated odor intensity and pleasantness under low and high distraction condi-tions. Respiratory movements were monitored to ensure accurate assessment of sensory percep-tion. No significant effects of distraction on odor intensity ratings were established. However, our findings reveal a significant reduction in odor pleasantness under high cognitive load, more pronounced in lean participants compared to those with overweight. Moreover, we observe an interaction between sex/gender and cognitive distraction effects in odor pleasantness perception. The differential effects of distraction across weight status groups and sex/gender are discussed in the context of hedonic motivations and compensatory mechanisms at play. This study sheds light into the mechanisms of distracted eating from the sensory perspective, that can pave the way for more personalized and effective strategies for promoting healthier eating habits in a world dominated by distractions.

Previous studies on the water-energy nexus mainly focused on the calculation and comparison of resource consumption at the national or regional level, lacking interprovincial sector-sector transfer analysis. In this study, the intensity of water and energy consumption of various sectors in China were calculated, the key nodes and paths of resource networks were identified, and countermeasures for resource conservation were proposed from the new perspective of the “dual saving” and “bidirectional saving” of water and energy. The results showed that the metallurgical industry (Me) in Jiangsu and the chemical industry (Ch) in Hebei and Jiangsu had high node strength in the water and energy network and were key sectors in China with “dual saving” effects of water and energy. The construction industry, Ch, Me in Jiangsu, electricity and hot water production and supply industry in Beijing, and Me in Hebei had high node strength in the water-related energy network and energy-related water network, significantly supporting the “bidirectional saving” effect of water and energy in China. The electrical equipment industry (El) in Jiangsu→El in Zhejiang, El in Zhejiang→El in Shanghai frequently appeared in key paths, which could effectively reduce the resource consumption of the entire network.

For 80 years high-intensity focused ultrasound (HIFU) has been a significant area for medical research. It is a non-invasive procedure which causes cell death in a highly localised area at a defined distance from the transducer. Since 2000, the clinical indications have broadened considerable as the technology has improved. This review looks back at the history of HIFU and the current clinical indications.

In the present work, a study has been carried out on the contamination of heavy metals in urban dust deposited on the roads of the city of Cartagena (Spain), in order to know the content of metals such as Ni, Zn, Pb, Cd, Cr and Cu. Likewise, the possible relationship of the concentration of heavy metals with the color of the sample, level of magnetism and traffic density was studied. Contamination was evaluated using several indices such as contamination factor (CF), enrichment factor (EF), geoacumulation index (Igeo), pollutant load index (PLI) and ecological risk index (RI). A total of 88 samples were taken in the urban area of Cartagena, and the metals were determined by acid digestion and measured by inductively coupled plasma mass spectrometry. The concentration of heavy metals in urban dust from Cartagena was Zn (672 mg/kg) &gt; Cu (248.9 mg/kg) &gt; Pb (227 mg/kg) &gt; Cr (82.7 mg/kg) &gt; Ni (47.7 mg/kg) &gt; Cd (4.1 mg/kg). Contamination levels were high in Pb, Zn, Cd and Cu, according to environmental indices. A correlation was found between magnetism and metal concentration, which was repeated for all metals except Cd. Dark-colored samples contained higher metal concentrations than light-colored samples. Meanwhile, streets with medium and low traffic intensity were found to have higher concentrations of heavy metals. This study's objective was to identify pollution hotspots caused by heavy metals in dust in the urban ecosystem of Cartagena city.

. Shrub patches influence soil fertility and vegetation, impacting species composition and diversity. The Eastern Qilian Mountains' unique context provides insights into alpine ecosystems' response to environmental challenges. This study aimed to evaluate the physical characteristics and soil nutrient contents of shrub patches for four different shrub species. Four alpine shrub species (Salix oritrepha, Spiraea alpina, Rhododendron capitatum, and Potentilla fruticose) were studied, assessing their patch characteristics and soil nutrients at different depths within three patch microsites. Soil samples were collected and analyzed for organic matter, nitrogen, phosphorus, and potassium content. Statistical analyses were conducted to evaluate differences among shrub species and locations within the shrub patches. Our results showed that the shrub species exhibited variations in patch characteristics and soil nutrient distribution. Soil nutrient content varied by depth and location within the shrub patches, with higher concentrations at the center. The relative interaction intensity (RII) showed nutrient aggregation or dispersion trends. The study highlighted the complex interactions between shrub characteristics and soil nutrients, emphasizing their influence on nutrient cycling, vegetation dynamics, and soil properties. These findings contribute to our understanding of alpine ecosystem dynamics and inform conservation and management strategies.

Type 1 diabetes (T1D) is associated with hyperglycaemia-induced hypoxia and inflammation. The study assessed the effects of a single high-intensity interval exercise (HIIE) on glycaemia (BG) and serum level of pro-inflammatory cytokines and an essential mediator of adaptive response to hypoxia in T1D patients. The macronutrients intake was also evaluated. Nine patients suffering from T1D for about 12 years and nine healthy individuals (CG) were enrolled and completed one session of HIIE at the intensity of 120% lactate threshold and duration of 4 x 5 min intermittent with 5 min rest after each bout of exercise. Capillary and venous blood was withdrawn at rest, immediately after and at the 24 h post-HIIE for analysis of BG, hypoxia-inducible factor alpha (HIF-1α), tumour necrosis factor alpha (TNF-α) and vascular-endothelial growth factor (VEGF). Pre-exercise BG was significantly higher in the T1D compared to the CG (p = 0.043). HIIE led to a significant decline in T1D patients’ BG (p = 0.027) and to a tendency for a lower BG at 24-h post-HIIE vs pre-HIIE. HIF-1α was significantly elevated in the T1D compared to CG and there was a trend for HIF-1α to decline, and VEGF, TNF-α to increase in response to HIIE in the T1D group. Both groups consumed higher and lower than recommended amounts of protein and fat, respectively. In T1D group, a tendency for a higher digestible carbohydrate intake and more frequent hyperglycaemic episodes on the day after HIIE were observed. HIIE was effective in reducing T1D patients’ glycaemia and improving the short-term glycaemic control. HIIE has the potential to improve adaptive response to hypoxia by elevating the serum level of VEGF. Patients’ diet and level of physical activity should be screened on a regular basis, and they should be educated on the glycaemic effects of digestible carbohydrates.

Although mountain areas account for approximately one fifth of the terrestrial surface, there has been less research focused on fire in these areas compared to lowlands. Mountain fires have distinct behavior due to dynamic winds interacting with the terrain, which can influence the fireline intensity and propagation. For the sake of fire safety of fire crews, it is essential to know how difficult to control the fire is in the mountain regions, with fireline intensity providing a useful indicator of risk and suppressibility. We studied one of the major disasters, wildfire, in Australia in such a highland by using the Great Pine Tier Fire, which occurred 15^th January in 2019, ending up burning approximately 511.86km². Weather and fire intensity at pseudo weather stations located at key points of fire progression were analyzed by wind vector maps and numerical weather model vertical sounding (NWMVS). Fire propagation was then simulated in Prototype 2, a fire simulator capable of detecting the potential for lateral fire channeling (LFC), and simulating fireline intensity using Australian vegetation sub-models. We found that the synoptic wind appeared to be modified by the interaction with the terrain in windward and the fire intensified the most in its leeward. In practice, the fire moved out of the valley axis and up its sidehill by following the wind which had been modified by local vertex of the curved valley axis before reaching this location.

Background: Low-level (LLLT) and high-intensity laser therapy (HILT) can be beneficial additions to knee osteoarthritis (KOA) rehabilitation exercises; however, it is still being determined which modality is more effective. Aim: To compare the effects of LLLT and HILT as adjuncts to rehabilitation exercise (LL+EX and HL+EX) on clinical outcomes in KOA. Methods: Thirty-four adults with mild to moderate KOA were randomly allocated to either LL+EX (n = 17) or HL+EX (n = 17) groups. All participants underwent their designated laser treatment combined with rehabilitation exercises weekly for twelve consecutive weeks. The Knee Injury and Osteoarthritis Outcome Score (KOOS), Numerical Pain Rating Scale (NPRS), active knee flexion, and Timed Up-and-Go test (TUG) were assessed at baseline and immediately post-intervention. Results: Post-intervention, both groups significantly improved their KOOS, NPRS, active knee flexion, and TUG scores compared to baseline (p &lt; 0.01). The mean difference of change in KOOS, NPRS, and active knee flexion scores for the HL+EX group surpassed the minimal clinically important difference threshold. In contrast, the LL+EX group only demonstrated clinical significance in NPRS scores. Conclusions: Incorporating HILT as an adjunct to usual KOA rehabilitation led to significantly higher improvements in pain, physical function, and knee-related disability compared to LLLT.

Knee osteoarthritis (OA) is the most common joint disease worldwide. Exercise therapy has been identified as a first-line treatment option in patients suffering from knee OA. High-intensity interval training (HIIT) is an innovative exercise modality with potential in improving various disease-related outcomes. The purpose of this review is to explore the impact of HIIT on knee OA symptoms and physical functioning. A comprehensive search of scientific electronic databases was conducted to identify the articles on the effects of HIIT on knee OA. Thirteen studies were included in this review. Nine compared the effects of HIIT with those of low-intensity training, moderate-intensity continuous training, or a control group. Three evaluated the effects of HIIT alone. Eight reported a decrease in knee OA symptoms, and eight reported an increase in physical functioning. HIIT was shown to improve knee OA symptoms and physical functioning, but also aerobic capacity, muscle strength, and quality of life with minimal or no adverse events. However, compared to other exercise modalities, no clear superiority of HIIT was found. HIIT is a promising exercise strategy in patients with knee OA: anyway, the actual quality of evidence remains very low, and more high-quality studies are needed to confirm these promising outcomes.

Atrophy quantification is fundamental for understanding brain development and diagnosing and monitoring brain diseases. FSL-SIENA is a well-known fully-automated method that has been widely used in brain magnetic resonance imaging studies. However, intensity variations arising during image acquisition that may compromise evaluation, analysis and even diagnosis. In this work, we study whether intensity standardisation can improve longitudinal atrophy quantification. We considered seven methods comprising z-score, fuzzy c-means, Gaussian mixture model, kernel density, histogram matching, white stripe, and removal of artificial voxel effects by linear regression (RAVEL). We used a total of 330 scans from two publicly-available datasets, ADNI and OASIS. In scan-rescan assessments, that measures robustness to subtle imaging variations, intensity standardisation did not compromise the robustness of FSL-SIENA significantly (p>0.1). In power analysis assessments, that measures the ability to discern between two groups of subjects, three methods led to consistent improvements in both datasets with respect to the original: fuzzy c-means, Gaussian mixture model, and kernel density estimation. Reduction in sample size using these three methods ranged from 17% to 95%. The performance of the other four methods was affected by spatial normalisation, skull stripping errors, presence of periventricular white matter hyperintensities, or tissue proportion variations over time. Our work evinces the relevance of appropriate intensity standardisation in longitudinal cerebral atrophy assessments using FSL-SIENA.

The assessment of the number of people exposed to natural hazards, especially in countries with strong urban growth, is difficult to be updated at the same rate as land use develops. This paper presents a remote sensing based procedure for quick updating the assessment of the population exposed to natural hazards. A relationship between satellite nightlights intensity and urbanization density from global available cartography is first assessed when all data are available. This can be used to extrapolate urbanization data at different time steps, updating exposure each time new nightlights intensity maps are available. As reliability test for the proposed methodology, the number of people exposed to riverine flood in Italy is assessed, deriving a probabilistic relationship between DMSP nightlights intensity and urbanization density from GUF database for the year 2011. People exposed to riverine flood are assessed crossing the population distributed on the derived urbanization density with flood hazard zones provided by ISPRA. The validation on reliable exposures derived from ISTAT data shows good agreement. The possibility to update exposure maps with higher refresh rate makes this approach particularly suitable for applications in developing countries, where exposure may change at sub-yearly scale.

The feasibility of a hurricane initialization framework based on the GSI-4DEnVar data assimilation system for the HWRF model is evaluated in this study. The system considers the temporal evolution of error covariances via the use of four-dimensional ensemble perturbations that are provided by high-resolution, self-consistent HWRF ensemble forecasts. It is different from the configuration of the GSI-3DEnVar data assimilation system, similar to that used in the operational HWRF, which employs background error covariances provided by coarser-resolution global ensembles from the NCEP GFS ensemble Kalman filtering data assimilation system. Data assimilation and numerical simulation experiments for Hurricanes Joaquin (2015), Patricia (2015), and Matthew (2016) are conducted during their intensity changes. The impacts of two initialization frameworks on the HWRF analyses and forecasts are compared. It is found that GSI-4DEnVar leads to a reduction in track, MSLP, and MSW forecast errors in all of the HWRF simulations, compared with the GSI-3DEnVar initialization framework. Further diagnoses with Hurricane Joaquin indicate that GSI-4DEnVar can significantly alleviate the imbalances in the initial conditions and enhance the performance of the data assimilation and subsequent hurricane intensity and precipitation forecasts.

Recently, light traps using light-emitting diode (LED) lights have been applied to monitor or control insect pests. The oriental armyworm, Mythimna separata Walker, is an important insect pest that has caused damage to several cereal crops, including corn, wheat and rice. The present study aims to seek out a sensitive wavelength causing high phototactic response in M. separata. The study evaluated the phototactic responses of M. separata moths to several LED lights of different wavelengths and luminance intensities under laboratory condition. Results showed that green (520 nm) LED light resulted in significant phototactic response of M. separata moths compared to LED lights of other wavelengths. Additionally, the highest attraction rate of the moths to green LED light appeared in luminance intensity group of 200 lux compared to the other intensities groups. Experiments under optimum conditions based on the above experiments revealed that the green LED light exhibited the strongest attraction rate (64.44%) among all experimental groups. An experiment performed in a net cage also showed that green LED light resulted in the highest phototactic response of M. separata moths, 1.7 times more than a commercial black light used as control. These findings clearly demonstrate that M. separata moths have a high sensitivity to the green LED light. Therefore, a light trap equipped with green LED light could be useful for monitoring and controlling M. separata moths.

Plants grown under fluctuating light impact plant developments compared with those grown under non-fluctuating light conditions. However, our knowledge on the underlying regulatory mechanisms is still quite limited, particularly from the transcriptional perspective. In order to investigate the influence of different light intensity distributions on tomato plant development, we designed three fluctuating light intensity distributions with the non-fluctuating light intensity as control and compared the transcriptional differences after five weeks of treatment. We found plant height and aerial/root weight were significantly reduced under all fluctuating light treatments. Transcriptome analysis revealed that the number of up and down regulated genes had a distinct distribution pattern between different treatments and control. The largest difference between the numbers of down and up regulated genes was found between treatment 1 and 3, reaching to a total of 416 genes. The number and type of the top 20 enriched pathways differed between treatments and control. The largest number of genes enriched was involved in the biosynthesis of secondary metabolites. These results provide insights into the transcriptional regulations of tomato under different light intensity distributions.

Various sudden shifts in financial market conditions over the past decades have demonstrated the significant impact of market structural breaks on firms' credit behavior. To characterize such effect quantitatively, we develop a continuous-time modulated Markov model for firms' credit rating transitions with the possibility of market structural breaks. The model takes a semi-parametric multiplicative regression form, in which the effects of firms' observable covariates and macroeconomic variables are represented parametrically and nonparametrically, respectively, and the frailty effects of unobserved firm-specific and market-wide variables are incorporated via the integration form of the model assumption. We further develop a mixtured-estimating-equation approach to make inference on the effect of market variations, baseline intensities of all firms' credit rating transitions, and rating transition intensities for each individual firm. We then use the developed model and inference procedure to analyze the monthly credit rating of U.S. firms from January 1986 to December 2012, and study the effect of market structural breaks on firms' credit rating transitions.

This article proposes a measurement solution designed to monitor instantaneous frequency in power systems. It uses a data acquisition module and a GPS receiver for time stamping. A program in Python takes care of receiving the data, calculating the frequency, and finally transferring the measurement results to a database. The frequency is calculated with two different methods, which are compared in the article. The stored data is visualized using the Grafana platform, thus demonstrating its potential for comparing scientific data. The system as a whole constitutes an efficient low cost solution as a data acquisition system.

We investigated the sleep-wake rhythm of nursery school children with the aim of supporting their health and balanced mental/physical development. We analyzed 4881 children from infant to 6 years of age, using 2-week sleep tables recorded by their guardians. The table contains sleep onset times, wake times, nighttime/daytime sleep duration, and the differences in these between weekdays and weekends. The total sleep decrement of children with age is due to a decrease in daytime sleep only, and nighttime sleep duration remains almost unchanged at about 10 hours, and is therefore called the nighttime basic sleep duration (NBSD). While sleep onset time stabilizes at around 9:30 pm by the age of 2, wake-up times to be before 7 am, resulted in weekdays sleep insufficiency. This lack of sleep is compensated by long naps on weekdays and by catching up sleep on weekends morning, which may be the background to future social-jet-lag. Guardians are encouraged to know their children's exact NBSD and set an ap-propriate bedtime to maintain it on weekdays, which prevent sleep dept and form a daily rhythm of waking up at the same time both on weekdays/weekends. These conditions are believed to maintain balance in mental/physical development and school-social-adaptation.

Historical analysis of Australian bushfire data spanning 170 years addresses whether the strength of recent fire events has been exacerbated by human-induced climate change. The question of “cause” looks at the characteristics of a wider range of natural hazards. Fire characteristics are compared with earthquake hazard characteristics: (1) energy – termed “magnitude”; (2) severity – termed “intensity”; and (3) resultant damage to people and structures – termed “impact”.Published global, Northern and Southern hemisphere temperature data are shown to vary consistently in phase over 170 years, but vary in amplitude with statistical significance. CO₂ levels north and south of the Equator have tracked quite consistently. Thus, Southern Hemisphere bushfire magnitude and intensity is compared with the Southern Hemisphere climate record, rather than a global data set.28 major bushfires and associated droughts since 1850 show neither apparent drought extent, nor area burned, nor bushfire intensity, correlates with changes in Southern Hemisphere climate. Average rainfall from 1900 shows a wetter, rather than drier trend. Cyclone energy shows no significant trend with climate. Planet-wide “greening”, through CO₂ fertilisation, is an insignificant contributor to bushfire magnitude. Combustion theory shows recorded “global warming” could have had no significant influence on bushfire magnitude or intensity. Any increase in Australian bushfire impact, as judged by lives lost, similarly, shows no correlation with bushfire magnitude, nor indeed, any observed Southern Hemisphere global warming.Thus, bushfire magnitude seems much more likely driven by fuel load and any anomalous bushfire intensity is likely driven by anomalous ground level fuel load. The evidence suggests that any CO₂ emissions reduction will have no impact on future bushfire “severity.

Using different frequency group period phase synchronization, a precise frequency detecting technology is presented. On the basis of the phase comparison for different frequencies, a high-accuracy frequency measuring can be achieved by quantization of phase comparison results and analysis of quantization results. Using the phase coincidence points between comparison signals as the counter’s open and close signals, the time interval between the same phase coincidence points is a group period. Via the detection and analysis of the phase coincidence points, the ±1-word counting error can be eliminated, and measuring speed is also improved. By using FPGA technology, the measuring device can be simplified, and the development cost can be reduced. Testing results indicate that the frequency measuring accuracy with 10−13/s level can be achieved. The technology is greater than the common frequency measuring technology in more ways than one, such as power consumption, device volume, measuring rate, etc., so it plays an important role in Beidou satellite positioning, precise timing, high-precision time frequency transfer and comparison, scientific metrology and other fields.

Keywords: Linear differential arrays; beam steering; frequency-invariant beamforming.

Whey protein was pretreated with multi-frequency ultrasound in mono, dual, and tri-frequency modes. The effect of multi-frequency ultrasound pretreatment on the hardness, chemical forces, and microstructure of acid-induced whey protein gel was investigated. Whey protein gels pretreated with dual and tri-frequency ultrasound showed higher hardness (p3.35 mm) in those samples were resisted to gastric digestion. Moreover, the tri-frequency ultrasound pretreatment of whey protein gel released the least free amino group during gastric digestion. In contrast, whey protein gel with the mono-frequency ultrasound pretreatment released the highest amount of free amino acid group during intestinal digestion. Findings from this study suggested that gel hardness and network density could modulate the digestion behaviors of protein gels.

The ANSYS 2024R1 student edition was used to create a finite element model of a basketball rim and backboard. This finite element model included the use of steel for the rim and its mount, a tempered glass backboard, and an aluminum frame behind the backboard. After a mesh was created, fixed support boundary conditions were applied to the four corners of the aluminum frame. The subsequently calculated mode shapes and frequencies were compared to empirical modal analysis previously done at the United States Military Academy at West Point, New York. Four mode shapes and frequencies agreed rather well between the theoretical finite element analysis and previously published empirical modal analysis, specifically where the rim was vibrating in the vertical direction, which was the direction that the accelerometer was aligned for modal analysis. However, three mode shapes missed by the empirical modal analysis were found where the vibration of the rim was confined to the horizontal plane, which was orthogonal to the orientation of our accelerometer.

The manuscript presents the applicability of the Gumbel distribution in the frequency analysis of extreme events in hydrology. The advantages and disadvantages of using the distribution are highlighted, as well as recommendations regarding its proper use. A literature review was also carried out regarding the methods of estimating the parameters of the Gumbel distribution. Thus, for the verification of the methods, case studies are presented regarding the determination of the maximum annual flows and precipitations using nine methods for parameter estimation. The influence of the observed data lengths on the estimation of the statistical indicators, the parameters and the quantiles corresponding to the field of low annual exceedance probabilities (p <1%) is also highlighted. The results are compared to those obtained with the Generalized Extreme Value distribution, respectively the Burr and the Wakeby distributions with parameters estimated using the L-moments. The results highlight and reaffirm the statistical, mathematical and hydrological recommendation regarding the avoidance of using the Gumbel distribution in Flood Frequency Analysis and its use with reservations in the case of maximum precipitation, especially when the statistical indicators of the analyzed data are not close to the characteristic ones and unique to the distribution.

Numerous experimental and theoretical studies undertaken to determine the effective-stress coefficient for seismic velocities in rocks stem from the importance of this geomechanical parameter both for monitoring changes in rock saturation and pore pressure distribution in connection with reservoir production, and for overpressure prediction in reservoirs and formations from seismic data. The present work pursues a task to determine, in the framework of a low-frequency laboratory study, the dependence of the elastic moduli of n-decane saturated sandstone on the relationship between pore and confining pressures. The study was conducted on a sandstone sample with high quartz and notable clay content in the quasi-static regime, when the 100 ml tank filled with n-decane was directly connected to the pore space of the sample. The measurements were carried out at a seismic frequency of 2 Hz and strains, controlled by semiconductor strain gauges, not exceeding 10-6. The study was performed using a forced-oscillation laboratory apparatus utilizing stress-strain relationship. The dynamic elastic moduli have been measured in two sets of experiments: at constant pore pressures of 0, 1 and 5 MPa and differential pressure (defined as a difference between confining and pore pressures) varied from 3 to 19 MPa; and at а constant confining pressure of 20 MPa and pore pressure varied from 1 to 17 MP. It was shown that the elastic moduli obtained in the measurements are in good agreement with the Gassmann moduli calculated for the range of differential pressures used in our experiments, which corresponds to the effective-stress coefficient equal to unity.

Predicting and evaluating the vitality level of public spaces of urban design is crucial before new construction and renewal, especially for developing countries, to avoid failures like "ghost neighborhood" and reduce resource waste. However, existing assessment methods for the urban vitality are either static and ignore changes in the time dimension, or rely on historical big data and are unable to predict unbuilt projects. This study combines previous methods and crowds’ characteristics observation in public space, puts forward the crowd-frequency hypothesis and constructs an algorithm, and establishes a time-dimensional urban vitality dynamic prediction model. Taking the Rundle Mall neighborhood in Adelaide, Australia, as an example, the effec-tiveness of the prediction model was proved through on-site observation sampling comparative verification method. In addition, the decision tree model was used to conduct machine learning on the case data, and a set of algorithm programs were obtained that can directly input some basic information to obtain the urban vitality level (high-medium-low) in a certain period. It can be used as a tool to support the design and decision-making processes of urban planners and government officials, providing a low-cost way to achieve sustainable urban vitality construction of late-developing cities directly.

We are currently investigating the ultrasound imaging of a sensor consisting of a randomized encoding mask attached to a single lead zirconate titanate (PZT) oscillator for use in a puncture microscope. The proposed model was performed using a finite element method (FEM) simulator. To increase the number of measurements required by a single element system, the transducer was rotated at different angles. The image was constructed by solving a linear equation of the image model. In a previous study, the image resolution was improved by extracting phase information. In this study, we propose a strategy by integrating the weighted frequency subbands compound and a super resolution method (SCM) to improve the resolution in range and lateral resolution. We also evaluated the image performance by applying different methods to improve the image quality. The results show that better image resolution and speckle suppression were obtained by applying the proposed method.

Six mode shapes, including bending and torsion, were documented for five different basketball rims and backboards at the United States Military Academy, West Point, New York, USA. The frequency and damping ratio of each mode shape were also determined. The empirical process began with the time-domain excitation and response of each rim-backboard system. The impulse of excitation came from an impact hammer separately applied to sequentially, to each node. The sinusoidal response was gathered from an accelerometer at a fixed location, node 1. Each time-domain excitation-response was then converted to a frequency domain Bode plot for each node by a B&K 2034 Signal Analyzer, giving transfer functions of output/input versus frequency. Structural Measurements System (SMS) Software was used to fit mode shapes to the Bode plots. Each of the six mode shapes were fitted to the Bode plots of each node at a specific modal frequency. Each of the six mode shapes were a function of the locations of the nodes, and the Bode plot gathered at each node. The first and second modes were critical for showing that the Energy Rebound Testing Device statistically correlated with the energy transferred to the rim and backboard. A known perturbation mass was selectively attached to the rim, to help isolate the dynamic masses and spring rates for the rim and backboard, to ascertain the kinetic energy transferred to the rim had a 95.67% inverse correlation with rim stiffness.

Dietary fiber has been associated with health benefits, therefore, the availability of validated tools to assess food consumption associated with high-fiber foods would allow the quantification of the intake of this functional nutrient, the identification of risk groups and target populations, and the development of public policies and/or programs aimed at improving the health of the population. In this study, a fiber intake short food frequency questionnaire (FFQ) was translated into Spanish and its content validity was determined by a group of experts, to subsequently conduct a pilot test including 198 subjects aged 36+12.5 years, residing in Chile (46 men and 150 women), with the purpose of quantifying dietary fiber intake. The global assessment of the FFQ revealed a validity coefficient of 0.98+0.02; after the application of the pilot, mean dietary fiber intake in adult Chilean residents was of 13 g per day, with similar results to those found in the National Food Consumption Survey 2010 (12.5 g per day in men, and 11.5 g in women). The FFQ is a quick and valid tool to classify people on the basis of their habitual dietary fiber intake.

Classical numerical methods for solving ordinary differential equations often produce less accurate results when applied to problems with oscillatory or periodic behaviour. To adapt them for such problems, they are usually modified using the exponential fitting technique. This adaptation allows for the construction of new methods from their classical counterparts. The new methods are usually more accurate, efficient and suitable for handling the oscillatory or periodic behaviour of the problem. In this work, we construct a two-parameter exponentially-fitted Taylor method suitable for solving oscillatory or periodic problems that possess two frequencies. The construction algorithm is based on a proposed six-step flowchart discussed by authors in related literature. Two standard test problems were used to illustrate the accuracy and performance of the proposed method.

This study proposed a spatially and temporally improving methodology adopting the Regional Frequency Analysis with L-moments approach to estimate rainfall quantiles from 22787 grids of radar rainfall in Taiwan for a 24-hour duration. Due to limited radar coverage in the eastern region, significant discordant grids were found in the coastal area of the eastern region. A K-means cluster analysis using scaled at-site characteristics was used to group the QPESUMS grids in Taiwan into 22 clusters/sub-regions based on their characteristics. Spatially, homogeneous subregions with QPESUMS data produce more detailed homogeneous subregions with clear and continuous boundaries, especially in the mountain range area where the number of rain stations is still very limited. According to the results of z-values and L-moment ratio diagrams, the Wakeby (WAK), Generalized Extreme Value (GEV), and Generalized Pareto (GPA) distributions of rainfall extremes fitted well for the majority of subregions. The Wakeby distribution was the dominant best-fitted distribution, especially in the central and eastern regions. The east of the northern part and southern part of Taiwan had the highest extreme rainfall for each return period. Both areas were frequently struck by typhoons. By using grid-based (at-site) as the basis for assessing regional frequency analysis, the results show that the regional approach in determining extreme rainfall is very suitable for large-scale applications and even better for smaller scales such as watershed areas. The spatial investigation was performed by establishing regions of interest in small subregions across the northern part. It showed that regionalization was correct and consistent.

The increasing penetration of renewable energy sources in power grids highlights the role of battery energy stor- age systems (BESSs) in enhancing the stability and reliability of electricity. A key challenge with the renewables’, specially the BESSs, integration into the power system is the lack of proper dynamic model for stability analysis. Moreover, a proper control design for the power system is a complicated issue due to its complexity and inter-connectivity. Thus, the application of decentralized control to improve the stability of a large- scale power system is inevitable, especially in distributed energy sources (DERs). This paper presents an optimal distributed hybrid control design for the interconnected systems to suppress the effects of small disturbances in the power system employing utility-scale batteries based on existing battery models. The results show that i) the smart scheduling of the batteries’ output reduces the inter-area oscillations and improves the stability of the power systems; ii) the hybrid model of the battery is more user-friendly compared to the Western electricity coordinating council (WECC) model in power system analysis.

This paper proposes a forecast-centric adaptive learning model that engages with the past studies on the order book and high-frequency data, with applications to hypothesis testing. In line with the past literature, we produce brackets of summaries of statistics from the high-frequency bid and ask data in the CSI 300 Index Futures market and aim to forecast the one-step-ahead prices. Traditional time series issues, e.g. ARIMA order selection, stationarity, together with potential financial applications are covered in the exploratory data analysis, which pave paths to the adaptive learning model. By designing and running the learning model, we found it to perform well compared to the top fixed models, and some could improve the forecasting accuracy by being more stable and resilient to non-stationarity. Applications to hypothesis testing are shown with a rolling window, and further potential applications to finance and statistics are outlined.

We show broadband sum-frequency generation (SFG) in the Green-Yellow-Orange-Red spectral range using bismuth triborate, BiB3O6 crystal (BIBO) as nonlinear material. We perform a noncollinear phase-matching configuration within BIBO crystal using the remaining light behind the second harmonic generation stage and the infrared idler of an optical parametric amplifier (OPA). The obtained mixing radiation of ultrafast light sources to generate femtosecond pulses across 520.5 to 742.5 nm region is observed. SFG spectrum from single-pass cross-correlation intensity over such visible range is showed. The SFG wavelengths as a function of tunable wavelength idler OPA agrees with the expectations of parametric conversion condition and open the door to practical multi-beam or multi-color sum-frequency generators.

Background: Actually, resonance frequency analysis (RFA) is the most extended method for measuring implant stability. The implant stability quotient (ISQ) is the measure obtained by the different RFA devices, however, inter- and intra- rater reliability and validity of some devices remains unknown. Methods: Thirty implants were placed in 3 different pig mandibles. ISQ was measured axial and parallel with Osstell® Beacon, Penguin® and MegaISQ® by 2 different operators and one operator performed a test-retest. Intraclass correlation coefficient was calculated to assess the intra- and inter-rater reliability. Pearson correlation coefficient was used to assess the validity. Results: The higher inter- and intra- rater reliability was obtained by Penguin® when measuring axial. The highest ISQ values were obtained using Penguin® in an axial measurement; the lowest, using the MegaISQ® in an axial measurement. The highest correlation values with the other devices were obtained by MegaISQ® measuring axially. Conclusion: Penguin® had a good reliability for measuring ISQ both inter- and intra- rater. Osstell® had good validity for measuring ISQ both axial and parallel and MegaISQ® had the best validity for measuring ISQ axial.

We report a broadband radio frequency (RF) channelizer with up to 92 channels using a coherent microcomb source. A soliton crystal microcomb, generated by a 49 GHz micro-ring resonator (MRR), is used as a multi-wavelength source. Due to its ultra-low comb spacing, up to 92 wavelengths are available in the C band, yielding a broad operation bandwidth. Another high-Q MRR is employed as a passive optical periodic filter to slice the RF spectrum with a high resolution of 121.4 MHz. We experimentally achieve an instantaneous RF operation bandwidth of 8.08 GHz and verify RF channelization up to 17.55 GHz via thermal tuning. Our approach is a significant step towards the monolithically integrated photonic RF receivers with reduced complexity, size, and unprecedented performance, which is important for wide RF applications ranging from broadband analog signal processing to digital-compatible signal detection.

The exact etiology of myopia remains elusive. The author proposes the particle property of photon in living tissue and the photon-electron theory in living tissue, if the frequency of the photon exceeds the threshold, the photon has enough energy to strike the electron away and forms a hole of a diameter in photon diameter scale in living tissue include the eye. Longer time of high-frequency electromagnetic radiation will cause more holes and a larger radius of holes. The visual light which passes through the radiated hole in the eye cannot be refracted on the macula, this is myopia symptom of blurred vision, shortening the distance of the eye and the object will include more visual light into cornea and lens, this is myopia another symptom of nearsightedness. The particle property of photon causes elongation of the eye and the macular holes.Blue light and X-ray are two kinds of high-frequency electromagnetic radiation which can shot holes in eye and cause myopia.

This paper proposes a novel deterministic methodology for estimating the optimal sampling frequency (SF) of water quality monitoring systems. The proposed methodology is based on employing two-dimensional contaminant transport simulation models to determine the minimum SF considering all the potential changes in the boundary conditions of a water body. A two-dimensional contaminant transport simulation model (RMA4) was implemented to estimate the distribution patterns of the total dissolved solids (TDS) within the Al-Hammar Marsh in the southern part of Iraq for 30 cases of potential boundary conditions. Using geographical information system (GIS) tools, a spatiotemporal analysis approach was applied to the results of the RMA4 model to determine the minimum SF of the monitoring stations with an accuracy level of detectable change in TDS concentration (ALC) of 5%, 10% and 15%. The proposed methodology specified a minimum and maximum SF for each monitoring station (MS) that ranged between 12 and 33 times per year, respectively. Additionally, increasing the ALC to 10% and 15% increase the minimum SF for some MSs by approximately 18% and 21%, respectively. However, the proposed methodology includes all the potential values and cases of boundary conditions, which increases the certainty of monitoring the system and the efficiency of the SF schedule. Moreover, the proposed methodology can be effectively applied to all types of surface water resources.

For the elimination of radio-frequency interference (RFI) in a passive microwave radiometer, the threshold level is generally calculated from the mean value and standard deviation. However, a serious problem that can arise is an error in the retrieved brightness temperature from a higher threshold level owing to the presence of RFI. In this paper, we propose a method to detect and mitigate RFI contamination using the threshold level from statistical criteria based on a spectrogram technique. Mean and skewness spectrograms are created from a brightness temperature spectrogram by shifting the 2-D window to discriminate the form of the symmetric distribution as a natural thermal emission signal. From the remaining bins of the mean spectrogram eliminated by RFI-flagged bins in the skewness spectrogram for data captured at 0.1-s intervals, two distribution sides are identically created from the left side of the distribution by changing the standard position of the distribution. Simultaneously, kurtosis calculations from these bins for each symmetric distribution are repeatedly performed to determine the retrieved brightness temperature corresponding to the closest kurtosis value of three. The performance is evaluated using experimental data, and the error in the retrieved brightness temperature is observed to be less than approximately 3 K from a window with a size of 100 × 100 time-frequency bins according to the RFI levels and cases.

Evaluation of the effects of a high-frequency acceleration (HFA) device on patient pain response to orthodontic forces. A multi-centered trial investigating pain sensitivity to orthodontic forces on 75 subjects at 4 study centers. Subjects underwent clear aligner treatment, with or without adjunctive HFA and documented their pain intensity using the validated NRS10 numeric rating scale. In-Office and At-Home ratings were measured separately for each subject for immediate and extended effect evaluations. Use of HFA devices in conjunction with clear aligner orthodontic treatment demonstrated significant reduction in subjects’ recorded pain ratings vs controls within 5 minutes of aligner exchange, (p = 0.006) and significant reduction in recorded pain ratings vs controls over a 7-day period following aligner exchange (p = 0.018). A 99.6% daily compliance rate with at home use of the HFA device was recorded for all subjects in the study. HFA significantly reduces pain attributed to orthodontic force. HFA delivers clinically significant immediate pain relief, and clinically significant extended pain relief over the 7 days following adjustment.

Introduction The prevalence of adolescent electronic cigarette (e-cigarette) use has increased in most countries. This study determines the relation between the frequency of e-cigarette use and the frequency and intensity of cigarette smoking. Furthermore, it evaluates the association between the reasons for e-cigarette use and the frequency of its use. Materials and Methods Participants were 68,043 middle and high school students aged 13–18 years from the 2015 Korean Youth Risk Behavior Web-Based Survey. Of the 68,043 participants, we analyzed 6,655 adolescents with an experience of e-cigarette use. Results The prevalence of ever using and current (past 30 days) use of e-cigarettes was 10.1% and 3.9%, respectively. Of the ever e-cigarette users, approximately 40% used e-cigarettes for ≥1/month and 8.1% used e-cigarettes daily. Daily e-cigarettes users were 10 times greater among daily cigarette smokers than among cigarette users for <1/month (18.1% vs. 1.8%) and 16 times more prevalent among those smoking ≥20 cigarettes/day than among those smoking <1 cigarette/month (38.9% vs. 2.4%). The most common reason for e-cigarette use was curiosity (22.9%), followed by less harmful than conventional cigarettes (18.9%), smoking cessation (13.1%), and indoor use (10.7%). Curiosity was the most common reason among less frequent e-cigarette users; however, smoking cessation and indoor use were the most common reasons among more frequent users. Conclusions Results showed a positive relation between frequency or intensity of conventional cigarette smoking and frequency of e-cigarette use among Korean adolescents, and frequency of e-cigarette use differed according to the reason for the use of e-cigarettes.

As the development of low-altitude economies and aerial countermeasures continues, the safety of unmanned aerial vehicles becomes increasingly critical, making the emitter identification in remote sensing practices more essential. Effective recognition of Radio Frequency (RF) signal attributes is a prerequisite for identifying emitters. However, due to the diverse wireless communication environments, RF signals often face challenges from complex and time-varying wireless channel conditions. These challenges lead to difficulties in data collection and annotation, as well as disparities in data distribution across different communication scenarios. To address this issue, this paper proposes a Progressive Maximum Similarity-based Unsupervised Domain Adaptation (PMS-UDA) method for RF signal attribute recognition. Initially, we introduce a noise perturbation consistency optimization method to enhance the robustness of the PMS-UDA method under low signal-to-noise conditions. Subsequently, a progressive label alignment training method is proposed, combining sample-level maximum correlation with distribution-level maximum similarity optimization techniques to enhance the similarity of cross-domain features. Finally, domain adversarial optimization method is employed to extract domain-independent features, reducing the impact of channel scenario. Experimental results demonstrate that the PMS-UDA method achieves superior recognition performance in automatic modulation recognition and RF fingerprint identification tasks, as well as cross both ground-to-ground and air-to-ground scenarios, compared to baseline methods.

Disruptions in power quality have a negative impact on many energy consumers. These include lighting, where interference manifests itself, among others, in the form of light flickering. The article presents phenomena accompanying the operation of modern light sources against the background of exemplary results of studies on the flicker of conventional light sources, such as incandescent or fluorescent lamps. To assess the effects of these phenomena, it is necessary to use measures other than those traditionally used. The results of measurements carried out in accordance with different recommendations take into account both power supply disturbances and the properties of modern light sources.

The marathon sport events and those who participate in these have grown over the last years reflecting notably an augmentation of women and master runners participation. The aim of the present narrative review was to briefly present the results of studies on anthropometric, physiological and training characteristics, as well as predictors of performance, in marathon runners. It was observed that performance was better in runners with small body weight, body mass index, body fat percentage, and rate of endomorphy. With regards to physiology, an increased maximal oxygen uptake, anaerobic threshold, and improved running economy could result in faster race time. The training variables that could predict performance involved weekly training volume (distance) and intensity (running speed), as well as history of training (years). A combination of these three broad categories of characteristics may offer an approximate estimation of the race speed considering that other aspects (e.g., nutrition, biomechanic and motivation) influence race performance, too. In summary, the findings of the present study provided an overview of anthropometric, physiological and training characteristics associated with marathon race time; thus, an optimization of any of these characteristics would be expected to improve race time.

The purpose of this study was to establish the association between total and segmental body composition (BC) variables and anaerobic performance and to create optimal models that best predict such performance in CrossFit® (CF) athletes. Fifty athletes, 25 males and 25 females (age: 33.26 ± 6.81 years; body mass: 72.57 ± 12.17 kg; height: 169.55 ± 8.71 cm; BMI: 25.06 ± 2.31 kg·m−2) were recruited to participate and underwent BC analysis using dual-energy X-ray absorptiometry (DXA) and an all-out laboratory test on a cycle ergometer (Wingate) to determine their anaerobic performance. The results show a significant correlation between BC values and performance, ranging from moderate (r = -0.34, p = 0.015) to near-perfect (r = 0.96, p &lt; 0.01). Furthermore, the created performance prediction models exhibited predictive capacities ranging from 19% (p = 0.017) to 93% (p &lt; 0.001). All prediction models were created using total or segmental lean mass variables, excluding others. BC and performance variables found significant differences between males and females. The findings demonstrate that BC variables are crucial indicators of anaerobic performance in CF athletes. Professionals responsible for athlete performance should use this information to monitor athletes and design training programs.

Event data loggers are frequently used to record the date and time of tip events in tipping-bucket rain gauges. The HOBO® pendant event data logger is one such commercially-available device commonly used for this purpose. It can record the contact closure of a TBGR reed switch at a maximum timing resolution of 1 second, tied to the timing of the logger clock, which is set each time the logger is launched. These event loggers are ideal for the routine recording of rainfall. This paper addresses the issue of whether they can also be relied upon when estimating short-term intensities, for which they were not designed. New experiments show that for a series of switch closures at fixed intervals other than exact multiples of 1 s, the HOBO® logger fails to record evenly-spaced tip events. Thus, for example, with pulses at fixed 2.75 s intervals, the logger records some events as occurring at 2 s intervals, and others at 3 s intervals. The duration between logged events is correct only when the mean is calculated for a long series of logged events. In natural rainfall, tip events can occur at any time, and inter-tip times, from which intensity can be estimated, will generally not be an integral number of seconds. Consequently, particularly in intense rain, the logger behaviour just described can lead to erroneous estimates of the rainfall rate estimated from the duration of individual inter-tip times. Possible solutions are discussed.

In this study, different configurations based on linear fiber lasers were proposed and experimentally demonstrated to measure the concentration of paracetamol liquid solutions in a range of 52.61 to 201.33 g/kg. The optical gain was provided by a commercial bidirectional Erbium-Doped Fiber Amplifier (EDFA) and the linear cavity was obtained using two commercial Fiber Bragg Gratings (FBGs). The main difference of each configuration was the coupling ratio of the optical coupler used to extract the system signal. The sensing head corresponded to a Single-Mode Fiber (SMF) tip that worked as an intensity sensor. The results reveal that, despite the optical coupler used (50:50, 60:40, 70:30 or 80:20), all the configurations reached the laser condition, however, the concentration sensing was only possible using a laser drive current near to the threshold value. The configurations using a 70:30 and an 80:20 optical coupler allowed to perform paracetamol concentration measurements with a higher sensitivity of (-3.00±0.24) pW/(g/kg). In terms of resolution, the highest value obtained was 1.75 g/kg, when it was extracted 20% of the output power to the linear cavity fiber laser configuration.

The aeroelastic response of lightweight low-speed aircraft with slender wings under extreme flow turbulence intensity is not well-understood. Experiments on a commmercial unmanned aerial vehicle (UAV) with a 3-meter wingspan and aspect ratio of 13.6 were performed in a large open-return wind tunnel with extreme flow turbulence intensity of T∞≈10%. The structural dynamics of the wing in the bending mode and the flow beneath the wing to capture the effect of aileron deflection was measured using laser displacement sensors and tomographic particle image velocimetry (PIV) techniques. The unsteady lift produced by the wing was also measured using a high-capacity load cell at an angle of attack, α of 2 degrees for three freestream velocities U∞ of 13.4 m/s, 17.9 m/s, and 26.8 m/s representing the UAV’s stall through cruise speed. It was found that high flow turbulence intensity with large integral length scales relative to the wing chord plays a dominant role in the large unsteady lift and wing displacements measured. The power spectral density (PSD) of wing structural vibration shows that flow shedding from the wing and the integral length scales have a significant impact on the overall power inherent in the bending vibration of the wing. Computation of vorticity iso-surfaces in the flow measurement volume surrounding the aileron reveal a striking observation; aileron deflection, δa of 10∘becomes less effective in producing additional spanwise vorticity, which is proportional to circulation and lift, at U∞ of 26.8 m/s because the freestream already has elevated levels of vorticity. A paradigm shift in design is suggested for light aircraft structures with slender wings operating in highly turbulent flow, which is to employ multiple control surfaces in order to respond to this flow and mitigate large bending or torsion displacements and the probability of structural failure.

Obesity and physical activity have opposing effects on cardiorespiratory fitness. This study aimed to investigate the impact of obesity measured by various anthropometric indicators and physical activity level on oxygen uptake and fat oxidation during moderate-intensity aerobic exercise in adults. Forty-eight individuals were recruited. Various anthropometric indicators (i.e., body mass index (BMI), waist circumference (WC), waist-to-hip ratio (WHR), and waist-to-height ratio (WHtR)) were measured. Physical activity was assessed using the International Physical Activity Questionnaire (a short version). Total oxygen uptake (VO2tot) and fat oxidation were recorded during 30-minute aerobic exercise at moderate intensity. There were no differences in oxygen uptake and fat oxidation between obese and non-obese groups. Based on obesity and physical activity, VO2tot was significantly different among groups classified by WHR. Inactive obesity had significantly lower VO2tot 28.1% compared to active obesity and 29.2 % compared to active non-obesity. The inactive obesity had a 3.8%, 27.4%, and 4.3% lower fat oxidation than the active non-obesity, as classified by WC, WHR, and WHtR, respectively. However, the differences were not statistically significant. We conclude that active obesity, as measured by WHR, exhibited higher oxygen uptake compared to inactive obesity. Moreover, inactive obesity showed poorer oxygen uptake than active non-obesity.

In the realm of power delivery to end-users, transformers are indispensable, with their malfunctions leading to substantial economic, safety, and environmental repercussions. The need for persistent surveillance is accentuated for in-situ oil-filled transformers, given the potential degradation of oil and the emergence of related ageing by-products. As the focus tilts towards online detection methodologies for transformer oil ageing, bypassing challenges associated with traditional offline methods such as sample contamination and misinterpretation, fiber optic sensors are gaining trac-tion due to their compact nature, cost-effectiveness, and resilience to electromagnetic disturbances typical in high-voltage environments. This work delves into the sensitivity analysis of intensi-ty-modulated plastic optical fiber sensors. The investigation encompasses key determinants such as the influence of optical source wavelengths, noise response dynamics, ramifications of varying sensing lengths, and repeatability assessments. Findings underscore that elongating the sensing length detrimentally affects both the linearity response and repeatability, largely attributed to the diminished resistance to external noise. Additionally, the choice of the optical source wavelength proved to be a critical variable in assessing sensor sensitivity.

The extent of single and multi-cropping systems in any region, and potential changes to it, have consequences on food and resource use raising important policy questions. However, addressing these questions is limited by a lack of reliable data on multi-cropping practices at a high spatial resolution, especially in areas with high crop diversity. In this paper, we describe a relatively low-cost and scalable method to identify double cropping at the field-scale using satellite (Landsat) imagery. The process combines machine learning methods with expert labeling. We demonstrate the process by measuring double cropping extent in a portion of Washington State in the Pacific Northwest United States--- a region with significant production of more than 60 distinct types of crops including hay, fruits, vegetables, and grains in irrigated settings. Our results indicate that the current state-of-the-art methods for identifying cropping intensity---that apply rule-based thresholds on vegetation indices---do not work well in regions with high-crop-diversity. Our deep learning model was able to capture the diverse nuances and achieve a high accuracy (99\% overall accuracy and 0.92 Kappa coefficient). Our expert labeling process worked well and has potential as a relatively low-cost, scalable approach for remote sensing applications. The product developed here is valuable to inform several policy questions related to food production and resource use.

Debris flows have generated major disasters worldwide due to their great destructive capacity, which is associated with their high energy levels and short response times. To achieve an adequate risk management of these events, it is necessary to define as accurately as possible the different hazard levels to which the territory is exposed. This article develops a new methodology to estimate this hazard based on the hydrodynamic characteristics of the flow and the granulometry of the sediments that can be mobilized by the flow. The hydrodynamic characteristics of the flow are determined through a mathematical modeling that considers the rheology of non-Newtonian flows and the different volumes of sediments that could be transported during events corresponding to different return periods. The proposed methodology was implemented in the Jamundí River basin (Colombia). The results obtained indicate that in the upper part of this basin there is a low hazard level, while in the lower part of the basin approximately 15% of the affected territory has a medium hazard level and the remaining 85% has a low hazard level. The methodology developed is simple to implement but technically rigorous since it considers all relevant aspects in the generation of debris flows.

This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

Many applications in agriculture as well as other related fields including natural resources, environment, health, and sustainability, depend on recent and reliable cropland maps. Cropland extent and intensity plays a critical input variable for the study of crop production and food security around the world. However, generating such variables manually is difficult, expensive, and time consuming. In this work, we discuss a cost effective, fast, and simple machine learning based approach to provide reliable cropland mapping model using satellite imagery. The study includes four test regions namely; Iran, Mozambique, Sri-Lanka, and Sudan where Sentinel-2 satellite imagery were obtained with assigned NDVI scores. The solution presented in this paper discusses a complete pipeline including data collection, time series reconstruction , and cropland extent and crop intensity mapping using machine learning models. The approach proposed managed to achieve high accuracy results ranging between 0.92 to 0.98 across the four test regions at hand.

The aim of this study was to evaluate the intensity of the annual sexual behavior (SB) of Boer bucks under tropical conditions in southern Mexico. For one year, 16 extensively grazing males were evaluated for SB individually with estrogenized goats. From the beginning of the experiment and every 30 days, body weight (BW), body condition (BC), testicular circumference (TC), odor intensity (OI) and SB (nudging, ano-genital sniffing, flehmen, mounting attempts, mounts with intromission, and self-urination) were recorded. The bucks showed a more intense SB during the months of November to May than during the months of June to October (p < 0.05). Greater frequency was found for nudging, ano-genital sniffing, mounting attempts, and self-urination in the months of November to May (p < 0.001). BW was lower during the months of January to August than in the months of September to December (p < 0.05). On the other hand, TC increased from October to December (p < 0.05). Similarly, the OI in males varied over time (time effect; p < 0.001). In fact, an increased odor was found from October to December. The conclusions were that breed male goats from the tropics of Guerrero have a more intense SB during the months of November to May, which corresponds to the time of the year when forage availability is the greatest.